I really liked my Maytag Bravo X washer. Until, at less than 2 years old, it started having issues. It all of a sudden starting sticking in the spin mode, then it wouldnt turn off even though the cycle was complete. I have to pull the plug out of the machine it to stop from continuously running. I was charged $104 to have a certified tech come out for 15 minutes and recalibrate it and it worked for another month. It started having that same problem again and now, I have learned I need a new control board, which costs over $200, plus labor, over $60. The Maytag service rep I spoke with was very pleasant when she told me she spoke with her supervisor and told me there was nothing they can. So now I dont like my pretty new machine at all, and have to decide if I should stick almost $300 into getting it fixed again, or buy a new washer, NOT A MAYTAG! As I voiced my complaint on the Maytag website I saw that there were many of the same complaints about the faulty control board and am wondering what does it take to get a recall?

It is actually an older model Maytag set that I bought used 4.5 yrs ago. I am very impressed how its held up and how fresh our clothes are still. I have always loved Maytag and will buy again if needed.

Absolutely the worst washer we have ever had. Clothes come out smelling and look like they havent been washed. I should have bought a cheap washer, I bet my clothes would have been cleaner. The machine makes you think it is the best ever made by the looks and the price. Im sorry I ever wanted my money.

Purchased washer in Jan 2013. Average usage is 1 load per week. Last week the washer started leaking from the rear left side. A service call discovered that the bleach dispenser was filling up with water and overflowing. Bleach dispenser?? I never use it! Seems that the new bleach dispenser hose line has a relief valve whereas the original part did not. Internet research has confirmed that this problem is very common with this make and model. However, a call to Maytag requesting what compensation, if any, would be available resulted in a response that basically was too bad... so sad... cant do anything for you! Seriously? An apparent common, known problem and all they can say is we understand your problem. Needless to say that will definitely be the last lonely repairman Maytag that this household will purchase.

We bought a Bravos model in May 2010. Two years later, the machine started making noise during the final spin cycle. We finally called a repairman who came today and informed us it was a bearing in the outer drum. The cost for the part (the drum assembly) was $290, not to mention the cost for labor. Since we only got the original warranty, the service center at Maytag refused to help with the repair. We, as others who have had problems with Maytag, bought the washer because of Maytags reputation. This is why we have to buy extended service warranties. Companies make trash! What happened to the days when an appliance lasted longer than 10 years? Why cant we buy a good sturdy appliance without superficial bells and whistles? We have no idea if any other brand is better, but we will not buy another Maytag.

Maytag Centennial - It came with the house. I think its a line made special for rent-to-own kind of places. I cannot stand the washer. It will not take fabric softener unless its in the ball and if you use extra rinse you dont get to use fab softener at all. (I like liquid fab softener on some things). Why it doesnt have a dispenser is beyond me. And the bleach dispenser is poorly designed, too close to the tub and splashes every time. Ive had this six months and would get rid of it in a heartbeat if I could afford to. Plus it snags towels. The washer is crap. And its a Maytag. I wish it would break so I could justify buying one that has some decent features like fab soft dispenser, bleach dispenser that doesnt splash, drum that doesnt snag.

Friends, Romans, Countrymen, At first I was skeptical and I once thought that I was the only one whose wife complained about the terrible soap stains and un-rinsed clothes. And finally my rinse and spin cycle stopped spinning and rinsing! However, after reading several reviews and complaints about the famous Bravo X He washer by Maytag and taking into consideration that there are over 650 complaints, making mine # 651. I now find I have lost all skeptical-ability and feel that we all may be comrades in this venture of purchasing the new trademark of the trade-mark Maytag. As almost all of us say our previous experience with Maytag was great. My parents had a Maytag since I was knee-high to a grasshopper and we were a family of eight. First we had the one with the rubber rollers, that was a work of mechanical genius. I even remember getting my arm caught in the rollers. Then my dad bought the spin dry model and that lasted a good 20 years. When I say the Bravo X at Sears it looked like the state of the art washer. However, and unfortunately I will have to agree with all of you. It is a piece of scrap metal and Maytag will not recall or recognize their mistake and make good on a recall or something. The least they should do is give us an old machine that does wash and spin to replace the new one that is less than 2 years old and does not work. I sure hope this letter does not fall on blind eyes. I think we may even have a collective lawsuit.Sincerely Yours;Mr. Lost All Skeptability!

Zero should be a choice on overall experience. I purchased a Maytag Bravo 300 from Lowes in February of 2011. Last week I was doing a load of laundry and the washer stopped in mid-cycle, and it gave an alarm and error code ld. I checked out the manual and it said there was a problem with the drain line. I check the drain line and it was fine, so I called Maytag to have a service man take a look at it. Before he even looked at the washer, he said it was probably the pump, and it is not covered under warranty. And he said that it would cost $140. He obviously sees this all the time. He explained that the pump is too small for the unit and it does not allow anything to go through the pump. Please make sure anyone who may be considering buying one of these units knows right up front that they are going to have issues with the pump, even if a small pebble gets caught in the pump.

DB7749SAM1 Maytag Stainless Steel Dishwasher worked great for 14 months then lights went crazy. My last machine was 30 years old before its motor died. I should have fixed it. Maytag needs to step up and fix this. I will make sure everyone knows from here on out, social media is a wonderful thing. I have not even used it that much - still looks brand new and this is unbelievable. I have seen so many bad reviews now on how Maytag has built poorly designed appliances and then to add insult to injury they will not fix their mistakes.

I purchased a new Maytag from Home Depot. It was delivered and installed by them on 7/20/12. Today is 9/18/12. It is less than 2 months old and the tub is starting to shred around the upper rim. I called to get it repaired. What a nightmare. First I tried to understand a Filipino woman through a bad connection. She advised me to call a different customer service number, 1-800-688-9900. I talked to Crystal. She called up information on me using my phone number. She asked for the serial number as she had the model number available from the online registration I completed on 7/20/12. I told her I do not have that and asked where it was located. I also told her that I was unable to get it at this time as I am handicapped. She advised me that I had to show my repairman the receipt or I would have to pay a $60 service charge. I get nervous about throwing good money after bad. So I then asked why. If the serial number is so important, why is it not a required info when you register online? She had no answer. I asked to speak to her supervisor. I waited 4 minutes. Enna finally came on the line. She gave conflicting info about my online registration. She said I was not registered online (if not, how did Crystal have all my other info including my model number? Why did Crystal tell me I had registered without the serial number?). Enna told me that the repairman could key in the serial number when he gets to my house and if my washer was under warranty, I would not be charged. Again I asked why, if the serial number is so critical to the process and with all the info they seem to have on me (name, address, phone number, model number, place of purchase, date of delivery, etc.), why is the location of this very critical number is not in the owners manual? Why do they allow you to register without it online and why dont they track sales and delivery by serial number? She was unable to address these issues. I asked to speak to her supervisor. She told me she would give me her supervisors name and number (Kim, **) but she would not give me a last name or contact information. She told me that she was the highest level that I was allowed to speak with.Bottom line, my Maytag is falling apart, getting through the red tape to get it fixed under warranty is silly. Maytag ignores its own concept of tracking by serial number and does not support the use of serial number by telling you where it is located on an appliance or requiring it to register online. Calling customer service is a joke! I was mad when my new $800 washer started to fall apart. Now I am just sad with the way we allow manufacturers to treat us. Mad about the way we allow them to operate in the United States. They create junk or junk parts overseas, products fall apart over here, calls for repair get routed around the world, and then they create more red tape and call it customer service. I made one bad choice. Hopefully, you are reading this and can avoid your own.

This is a Maytag Neptune MAH8700AWW. This machine has been repaired a couple of times already and it has a will of its own. When it goes into that fast spin cycle that will kicks in and it starts moving. I wonder if someday its going to attack me. So, last Friday night we put a load in and it went into that fast spin cycle. It was making a noise like an elephant in labor so I looked in the laundry room.... Clouds of smoke were billowing out of the top of the machine. Our house will filling up with washing machine smoke! My husband stopped it, but I think it was a gnats hair close to bursting into flames. He looked into the front of the machine when the smoke dissipated and the entire gasket was in shreds. No more Maytag. Never. Im done.

Maytag Dishwasher MDB7749SBW3 - Control panel problem just like everyone else describes. Bought in Nov 2014... how disappointing!! My husband is sure he can fix it if I buy the part. I went online to order the control panel, and of course because Im in Canada I cant ship the part directly from the website, I have to call the Canadian Sears Part Dept., its about $200! As I came across all these reviews I am even contemplating if I should waste our time and money trying to fix this thing... Maytag never again!!!

Purchased a Maytag Bravo. One of the worse purchases weve ever made. First the much of the clothes does not get submerged. 2nd the clothes comes out extremely wrinkled. Called the Maytag people and they explained that Im putting too much clothing in the washer. I explained Im only filling the washer half way. They explained it should be filled only a quarter of the way. What??? Do not purchase this machine.

My husband and I purchased this Maytag bravo washer in May 2014. It is not even three years old and the bearings went out. Call the repair man and it would cost over $300 to have it fixed. I paid a lot of money for this washer, expected it to last more than less than a little than three years and I think its terrible. Its loud, water was leaking all over the floor, its just a terrible terrible washer. Maytags reputation is not as good as it used to be. Model number mvwx5008wq and ser number. C41430792. If you are planning on buying a washer do not choose Maytag!

I purchased Model #MHW563HW Frond loading automatic washer a little over 1 year. The options are not for me. The quick wash is way too short 20 minutes, all the rest of the options are 51 minutes to 2 hours & 57 minutes! If you wanted to add some extra minutes to the Quick wash you are out of luck. Normal wash is 55 minutes but can last much longer, it takes forever for this machine to balance which adds time to the process.I had an LG front washer before this one and when the clothes came out they were almost dry, not this washer, they are very wet. Then there is the horrible odor that comes after you use it, Ive tried drying every area making sure there isnt a drop in it. Still the stench is unbearable. Yes it has a Clean Washer with Affresh option which takes an additional 128 minutes and you have to do it at least once a week! Thats a LOT of wasted energy. That just doesnt sound efficient to me, washing the washer. Why??? This washer had great reviews which I read, not one mentioning these issues.

Bought a Maytag Bravos XL washing machine because I thought it was a dependable brand. We have had it 14 months and the lid (upper left corner) will not stay connected. I called Maytag and the rep states to me Is it broken in the upper left corner and I replied yes. He continued he is just the parts guy, but every bravos has the same problem. I asked for the replacement part ($302), but he said the part is on back order for 60 days. He continued that maybe I should buy two because it will happen again. I only paid $700 for the washer, but it should never break down after 14 months. I highly recommend a different brand.

I purchased a Maytag Bravos 5 months ago. I had trouble at first with unbalanced loads. The repair man came to look at it twice. One thing that can unbalance your loads is if small pieces of laundry such as a sock gets outside the basket. Sometimes the basket has to be taken all the way out because small pieces can be lodged under the basket. This happens when you fill the machine too full and those small pieces float to the top.The suspension on my machine ended up needing to be replaced. I have read lots of reviews about soap rings in the clothes. That happens from using too much soap. Make sure you are using HE detergent for one. I cut way back on my soap and my laundry gets clean and no problems with residual soap on my clothes. I was very unhappy with my machine at first but now I absolutely love it!

Washer needs new transmission at only 3 years old! Maytags 10 year part replacement doesnt cover it. The company actually asked why I didnt purchase extended warranty, I thought I didnt need one. Bad bearings, it doesnt wash the clothes clean, $400 to fix it. Needless to say Im buying a new washer and it will not be a Maytag, worthless piece of scrap!

We purchased our Maytag through Sears. We wanted a very basic machine, and thats what we found at Sears, yay! Fast forward eight years and it suddenly quit agitating. We tried fixing it ourselves by replacing a plastic gear part, which, later on our appliance technician said was totally logical, but it still wouldnt work. We got our appliance repairman out here and he took it into the shop and fixed the problem, which turned out to be part of the motor or something like that. The thing that bothers me the most is that he asked if we had bought a refurbished washer, but we hadnt, it was brand new. He gave us a part that was swapped out that wasnt made for the machine and also said the safety guard for the cord was missing. This keeps it from pulling out of the machine in case it gets jerked. I feel deceived and just wanted to vent because there really isnt anything I can do about it now. Buyer beware, yes, but I know we have to be our own technician sleuths to be sure were getting what we paid for?

Purchased washing machine, with insurance that was offered to me 9/17/10. May 2013, control panel went. June 2013, dial switch went. July 2014 washer motor drive & belt drive had to be replaced. August 2015 is broke again. Will never buy Maytag again.

We got Maytag 2000 series front load washer just over a year ago. The bearings in the drum are already worn out. I will never buy a Maytag again.

I bought this large capacity top loading wash machine about 22 years ago and it has yet to fail me. It had never needed any repairs and cleans my clothes wonderfully. The brands reputation is well earned. Great washer!

I have ALWAYS bought MAYTAG since the 1970s. But MAYTAG is no more. Whirlpool bought them out. I have an HE (first mistake)... HE... will go away just like low flow toilets did!!! You cannot wash clothes in 4 of water. I bought a top loading Brazos XL for $1100 (second mistake)... Have had it just over a year! I should have returned it but did not. Huge mistake (#3)... Repairman told me to get rid of it as fast as I can. Will eat me up in repairs. Now needs repair again for another NEW issue... The fill sensor does not tell the machine to load the proper amount of water. Now I cannot clean washer, tried three times last night. I am beyond upset. Repairman said buy GE! You can bet it will NOT be High Efficiency!!!!!

Maytag Washer over 3 years old. Often problematic not functioning smoothly! Maytag invented this defective machine to intentionally rob the customer with all the probs that comes with it - poor design & quality, & not logistically programmed! Even aftercare/customer service SUCKS!!! Now, sensor spinning option is no longer working, drum not operational. No more Maytag!!!

I purchased a Maytag Epic Z Front Load Washer less than 5 years ago, and there is only 1 person in my household. I replaced a part that the technician said was bad for $300 and that didnt work, so they replaced another part for another$ 200. Then, when that didnt work, Whirlpool deemed my washer irreparable, and they will not stand behind their product. This is totally unacceptable, and I will never buy another Whirlpool product. I will also tell others that they do not stand behind their product. If this was a 20 year old product, I would understand but it is not typical for something like this to happen.

This machine (Top-Loading High Efficiency MVWB755DWO) does not clean, it only leaves soap and moldy residue on clothes. The Whirlpool company refuses to assist even though it was delivered less than a year ago. So much for warranties! Wrinkles clothes, wrings incorrectly and does not give you freedom to manage independent of technological controls.

From day one I didnt like how this machine restricted how I can wash my clothing. There is no water volume controller. It is all automatic, which sounded fine in the store, but once I used it I quickly realized it is horrible. I can not add extra laundry or detergent in at the last minute because it says not to open the lid at all once you start the load. The settings are very glitchy. They do not seem consistent. There is a knob for level of soil on the clothing which doesnt seem to do anything at all. Ive had it now for four years and it has only gotten worse. Now I can only use one setting Hand Wash. Try doing a teenage boys clothes in Hand Wash and youll find out quickly that nothing gets clean that way. Oh, and all of the sudden the spin cycles are not working, they spin when they want to but they rarely get rid of the dirty water. Spinning in dirty water does not get clothes clean either. This machine is horrible, hands down, the worst washing machine I have ever owned.

We have only had this Maytag Washer for 3 1/2 years and the bearings went out. There is just my husband and I in the household and we are retired. We only use the washer once or twice a week. The repairman said the whole tub (inner/outer) would also have to be replaced. We paid $1,126.03 for the machine and it will cost $700 to repair it. Needless to say we will not repair it but will buy another washer. We have always been satisfied with Maytag appliances until now. We probably will not buy another Maytag appliance due to this event.

The machine had automatic fill which did not allow enough water to rinse the clothes properly. I had to run another cycle to rinse the clothes. The machine was also extremely loud. When I had a warranty repairman come out concerning these two item as it was brand new, I was told I should have researched better. I gave it away after 3 months.

Under class action suit in 8/2005, Maytag repaired my Neptune washer by replacing motor conversion kit. 6 yrs later the washer is having same problems as had originally; we asked Maytag just to replace the motor drive again ($190.00 part). They refuse, although this motor drive had identical life span to the one they replaced. It seems the replacement part was not new and improved, it only lasted as long as the original. Only now, we are past the class action suit deadline by years.

I purchased this product at an authorized Maytag dealer sixteen months ago (Maytag front-Loading washer, model MHWE55OWW1) for approximately $1,500. The main bearing and drum are now shot. Maytag has acknowledged that it is likely defective. Notwithstanding their conclusion, Maytag has chosen not to offer a repair or replacement. The conclusion is simply that Maytag does not make a very good product, and any prospective purchasers can expect that they will not get any customer support for their products.

July 2011, I bought a top loader Maytag washer from Best Buy. In October, after I had the washer just a little over 3 months, it quit working. Dead. I called Best Buy that said they only stand behind a product for 3 months and since mine was about 3 months and 2 weeks old, I had to contact Maytag to fix it. When I contacted Maytag, it took them 3 long, angry, upsetting phone calls before they finally made an appointment for someone to come look at it the next week. I was without a washer for 9 days and when the man came, he said it was too new for parts. He would order a new latch (apparently, he thought it was not latched and so would not run), but it would take a while to get it in. Hed call me. 3 weeks later it and he showed up. He said apparently, the latches were bad because the new one didnt work either. He would order one more and if it didnt work, he would have to order a new back panel and it could take a few months, instead of weeks, for it to come in. The second new latch finally came in and the washer still did not work! However, he reprogrammed its computer to accept the new part and it finally worked. By now, it was the end of January 2012! My new washer I had paid for in 3 payments had been broken down longer than it had run! Best Buy said basically, you buy it, its your problem. Maytag said basically the same thing. They were hateful and it took over 10 phone calls to get anything done! I was not reimbursed for any laundromat usage, gas or phone minutes, of course! I was treated like I was expecting something that I had no right to have, a working product. Once I bought the product, it was my problem and not theirs. The end. I will never buy another Maytag product!

The washer we bought has a leaking drain pump after 3 years. When I called, they initially told me the part has been flagged as a potential quality issue. When I was passed to the next level to deal with it, they stuck to the you only have a 1 year warranty policy. There are numerous websites indicating this has been an issue for these brands. Simply put, they dont stand behind their products.

The Neptune Front Load Washing Machine I purchased in December of 2007 started sounding like a jet taking off, about three months ago. The noise has become unbearable. The repair person said that the whole drum needs to be replaced and it is not worth fixing. Are you kidding me? This was an expensive washing machine and now we have to get a new one? We cannot afford to get a new washing machine. We need an explanation of why this would happen and from the other complaints I have read on the Maytag website, we are not the only ones. This is the second time something has happened to this washer, the first time, it was under warranty (only a few months into the purchase and the pump was bad and was replaced). What is the company doing to help people with this faulty machine?

We’ve had our Maytag washing machine for 29 years, and it’s still going strong! We’ve only had it repaired once in all those years. It’s a top loading washing machine. It has a suds saver, and a gentle cycle, too.The agitator’s in the middle of the barrel. Although it’s an old machine & not as energy efficient as the new ones are, we’re planning to keep this one for a while. Too bad newer machines are expensive and aren’t built to last!

I have had this machine for 15 years and never spent a penny on any maintenance, I love it. Some things are worth it and it still has a stylish look and cleans great. The only thing I would change is if it didn't have any the middle washer paddle so it would have more space like the newer models.

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.

I have a new HE (high efficiency) washer. It takes getting used to as its a definite change from the old agitating system but I think I like it. It doesnt make much in the way of suds but everything still comes out really clean. The wash cycle is much longer than my old washer but it uses a lot less water.

The digital display on our Maytag Washer model MVWB765FW, bought 3/22/2017, failed overnight (whilst the machine was not operating) after 3 1/2 years. A reputable firm came out and diagnosed the problem, their report concluded that the Control Board had failed and needed replacing: they provided a verbal quote of $525 [ ! ] to do that. The machine cost $600 and based on the expected life for washers (per Consumer Reports) of ten years would have a maximum residual value of $420 based on straight-line depreciation. The retailer from whom we bought the washer told us that he had contacted Maytag and asked them what they were prepared to do about this failure: a week later and absolutely no response from the manufacturer. Apparently Maytag has no concern for their customers or their own reputation. We made the mistake of buying this machine based on Maytag’s reputation and a ten year warranty which appears to cover only parts unlikely to fail! NO MORE MAYTAGS FOR US.

I bought the Maytag MVWX700XL1 (Bravos X) model in 2012 from Home Depot. I paid over $800 for this washer. I knew I was in trouble when I found dry spots on clothes after the washing completed. I started using the Bulky cycle. So much for saving water. It has not been overused, its only two of us. Today the spin cycle sounds like a train. The washing cycle has stopped working completely. Im very dissatisfied with this washer.

Purchased a Bravo set 5 years ago. Paid $730. For the washer. 4 repairs in 5 years. It is now has a bearing out and that will cost $450. MAYTAG used to be the best... buyer beware!

Worst washing machine I have ever owned. Read all the other reviews and concur with them. We get pin sized holes all the time. Brand new shirts yesterday and they have black stains all over them - not the first time either. Inside of stainless steel tub looks clean. Where do the black marks come from? Last Maytag I will ever buy!!

Purchased this washer from Saginaw, Michigan location in 2007. Started sounding like it was going to come through the wall of the laundry room so I contacted repair service. Told bearing was bad and that cost of repair would be $1,000.00 - literally laughed at repairman. I find it difficult to believe that a washer is built to last 7 years after paying so much for it.... My years of purchasing solely from Maytag have thus ended.

Washer is noisy and water does not saturate clothes on normal wash. Have to use sheet setting for small or large load. Washer changes gears and it is so loud and clanks like something is falling apart.

Maytag MVW823OHC SLATE washing machine, $1050 plus warranty $169.95 on 05/27/21 not delivered until 06/25/21, error code on 09/19/21. It is 11/03/21, machine is not working and no part available. Sad.

Purchased new Maytag washing machine July 17, 2011. Have had several problems with it over the past three years. Most of the time it would not complete a load of laundry and would get stuck before the drain and spin cycle. Last week, the spin cycle became extremely loud. Had a repair person come out and was told the motor bearings were bad. Estimated repair cost $700. Purchased this unit new for $569.00. Called Maytag, was told that 10-year warranty on drive motor and wash basket did NOT include the bearings. Asked if they could help out with repair cost, was told no. Will never purchase another Maytag product again as they do not stand behind their products. Household has 4 people in it so use of this machine was light to medium.

I bought the bravo 2 1/2 years ago. It started making loud banging noises during the cycle. I constantly had to rebalance my load. Then it stopped spinning at the end of the cycle or it would leave clothes wet. We had a repairman in and he told us that it would cost at least 600.00 for a new computer. Plus labor. Wow!!! I think a washing machine should last longer than that. Maytag should have a recall on this machine as I have read so many complaints about it.

Maytag Centennial washer - Bought this washer brand new and after the first 2 months started having issues. The washer took FOREVER to fill and to complete a basic load took literally an hour or more. Then within the next 7 months it stopped spinning out the final spin cycle. Spin light would flash as would lid lock but wouldn’t spin the water so I had to manually unplug the machine then plug in out cycle on drain and spin and that worked 50 percent of the time. Repairman came out and said could be a number of issues but he said honestly it would cost me a lot less to just go buy a new washer! This is INSANE! I grew up with the Maytag repairman commercials and thought Maytag was still top of the line but LEMME TELL YA, IT AINT! The Centennial is a total piece of crap so PLEASE don’t purchase this machine as I can promise you will NOT be satisfied! MAYTAG, STEP UP YOUR GAME BECAUSE YOU SUCK.

Very disappointed with Maytag Bravos XL, four year old unit with bearings going out. Quoted $400 + for repair. With two in the house, wash demands are normal. Quality is questionable to have bearings & seal going out in four years. Also you cannot buy the bolt which holds the Washer Motor Rotor Cover on without buying the whole $130 assembly. Daughter has Whirlpool brand with same problem. Seems to me this is a problem Maytag/Whirlpool should address. My old unit (that I wish I still had), worked for 25 years. Would not recommend these machines.

It is nice to know that there are other people out there that have the same problem with the Maytag washers cabinet inside and outside rusting. Our rusting is around the bleach area rim and on the outer seam of the washer. Our washer is now 4 years old. We started having the rusting problems in 2011. We called Maytag and of course. They are sorry for our problem but cant do anything about it. They made it sound like we were the only ones having this problem. We need to stand strong and continue to complain about this problem until Maytag takes responsibility for their poor quality washers. Anyone out there looking to purchase a washer. Do your homework. Buyer beware of Maytag washing machines!!!!

I have a Maytag washing machine for close to 20 years, so when it was time to replace it, I bought another Maytag: the Bravos. I read reviews, and most negative ones complained that it used too little water, twisted clothes, and was noisy. But I wanted an HE and can tolerate noise just fine. What I cannot tolerate is the fact that -- less than 2 years after purchase -- the control panel is malfunctioning, and it will cost $500 to repair. Id rather buy a new washing machine than throw good money after bad on this one. Bye-bye, Maytag.

I bought this machine a year and a half ago. The entire drum and spin motor need to be replaced. Maytags warranty only lasted 1 year. I bought it at Home Depot, and also purchased the extended 5 year warranty. The extended warranty is as bad as the washing machine. I am now just 2 days shy of 4 weeks of trying to deal with both parties. Ive had to take my laundry in to have it done. The cost of the laundry, the cost of the machine, and the cost of the warranty is more than $200 more than what Home Depots Extended Protection Plan is willing to reimburse/refund. Home Depot does as much as Maytag when it comes to standing behind what they sell. An $800 washing machine only good for 18 months, really???

This machine does a great job at cleaning clothes. The clothes are always great in color, and removal of removable spots. The cycles are not too long and the machine is not noisy. Machine is nice looking and water cycles can be normal or large.

Maytag Neptune Washer Drum Bearings have once again failed. Last time, I replace the whole drum via diy, cost was about $160 for the part. Now I see that outer drum is $500 +/-. I just may only replace the Seals & Bearings this time OR just part this thing out and buy a real machine without the Maytag name.

I bought this washing machine 2 years ago or so. We have always bought Maytag. My mother still has hers she bought over 25 years ago and it still looks and works great. So my wife wanted a new washing machine so I said were going to get another Maytag. Boy did I screw up. What a piece of ** junk. Sounds like its grinding gears all the time, so loud. I close the door in the wash room and I can still hear my investment on a Maytag grinding my nerves because I spent so much on a product of a brand Maytag that I thought would be around for a while. Do not buy a Maytag.

I inherited the Maytag Bravo washing machine when I got married... should have stuck with my LG! The Bravo does not clean clothes properly, I have to wash fewer items in each wash and wash them on the power cycle! Wasting time, water, and electricity! Will be purchasing a different brand!

It sounds like an old threshing machine... I have to close the laundry door it is so loud. People cant believe its a new machine. So saving water is the big deal we hear so much about...but water is the main cleaning agent and it hardly covers the clothes even on a full load coverage. Do not use bleach in the machine unless the load contains ONLY WHITES. It just destroyed a new pink top as it spurts out the bleach without any controls. It does not get whites or clothes clean and just twists the clothes to the point everything you wear has to be ironed. There is not one good thing I can say about this pair of appliances except BUYER BEWARE~ I wish I had read the reviews... Buy the old...tried and true.

Bought this because it’s American made. It seems to be very glitchy. If you don’t use the detergent drawer it always flashes low detergent. The quick wash leaves soap on clothes. It acts up and leaves clothes too wet. No buzzer to tell you when it’s done. Have to hold button for 3 seconds to start. You can’t just hit button and walk away. Then wait for it to sense the load first to make sure it starts. Very expensive model.

I purchased a 5 Maytag appliances in the last year. Stupidest thing I have ever done. The clothes washer being the worst. Front Load, model # MHW3505FW1. Last night I threw 5 small, lighter weight things in the washer on normal cycle, med temp, max extract... like usual. An hour and thirty-eight minutes later (normal cycle time), I opened it to find most things never even got wet. One scarf was still folded in fourth - the way I put it in! I called service even though I know there is nothing wrong with the washer, other than being so poorly designed, it cant get clothes wet with a damn tub and a hose. After I told her the problem, she puts me on hold, comes back to tell me she researched this everywhere and she found that this is a symptom of a NEW washer! Its SOO efficient that you cant even tell it was wet! Bull. Most of the items were brand new and you could see the original creases and smell the new smell. They CLEARLY were never wet. They wanted to set up an appointment for servicing, so now I have to be here for them to tell me nothing its not broken. I will never buy another Maytag again.

Had the washer for less than 3 months just a week before the 90 warranty was up and it stopped spinning. Called service dept. What a joke for this company that keep yessing you. Took a week before someone came out. Said washer needed a new motherboard and they would only cover it once but there seems to be a ongoing issue with their motherboard. Had to wait over 2 1/2 weeks before they would have one in stock. The tech installed it however now when it spins seems she left the top loose.

I have always bought Maytag products, but I will never buy another one again. This washer is the worse. It never has gotten the clothes clean and it is so loud. It has gotten worse. I called someone out to look at it and now am being told that the bearing is going out. We havent had the washer for two years. The cost to repair is going to cost us $574.00. That is crazy. We are going to let it go out and buy another washer, but NOT a Maytag. I will do my research before buying a new washer.

I purchased this washer... the Maytag Bravos. It is the worst clothes washing experience. I only use one cycle as the other cycles do not provide enough water to wet the clothes. It is a large capacity top loader. DONT DO IT!

Because it is the high efficiency model, need to leave the lid open so interior will dry and not smell musty. Also, recommend using a washer cleaner such as Affresh or Tide tablet every now and then. But works great!

I sold my 20 year old Maytag set and upgraded to this Maytag Bravos washer. This machine takes almost 1 hour to do a load and they come out dirty. Only way to get clean is to set on bulky sheet which uses twice as much water as old machine. This unit should have never been put on the market.

Maytag Centennial Washer - Bought washer because of brand name and was that a mistake! This is the Loudest, noisiest, banging clanking washing machine I have ever heard. Every time I do a load of laundry the washer moves a foot from the wall and I have to continually move it back. Needless to say I hover over it all the time when I do laundry. It isnt even 2 years old and we are going to go buy a new machine, AFTER looking at reviews!!!

The worst washer I have ever purchased. Clothes DO NOT come out clean, smell musty after washing. Have even decreased the amount of clothing per wash. Cant use bulk load function: throws LF Code - Bad water valve. I will NEVER buy or suggest anyone buy this piece of JUNK! Then to top it off you have to constantly chase the machine around due to wash load becoming unbalanced. Now today have to contend with a burnt smell...

Fifteen months after purchase of the top load washer, we have had to call in repair. The lid lock and sensor have went out on the machine and the repair costs are equal to the purchase of the machine. Whether the consumer has an extended warranty or not, this is unreasonable. So hear this Maytag, the CONSUMERS will invest elsewhere when delivered cheap merchandise like this even if it is Made in the USA as you wish to tout in order to bait the consumer for their money instead of providing superior quality American products. This consumer is sending this machine out the door.

Dont buy their washers. Plain and simple. Will never ever buy Maytag again. This washing machine is garbage and I paid a lot of money for it. 3 months out and it had to have the entire circuit board replaced. I was assured that this was the issue. It has never cleaned our clothing, in fact, they come out twice as dirty and with soap. Weve used the Affresh, weve put as little as 1 tablespoon of detergent, weve triple washed several loads and still ended up having to wash them by hand in the tub. Changing the circuit board did nothing. Weve tried setting it to max fill (which it does) and everything still comes out the same. Its not the water, its not the water hook ups (previous washer worked great but was old, should have kept it). This is the worse product that Ive spent almost a thousand dollars on. Its a paperweight. On top of this, it twists your clothes into a mass. I expect companies to be honest about their products and provide what I paid for. How many times does this washer have to be fixed before you will call it a bad design? Im having to literally do all my laundry by hand for the last 8 months. I want my money back so I can buy a good quality product that works. I could have bought a $300.00 washer that would have done better then this. You want more proof, go read their Facebook replies to all their posts. Its all complaints about their washing machines. It would be nice for once to see a company fess up and say they made a design error. But that wont happen. Their money is more important.

We bought a Maytag Bravo washer and after less than 6 months of use, it stopped working with an F51 or 53 error (cant remember which because its been a month now). After looking online, it seems that almost everyone who buys this gets this error and has to have a part replaced! And Whirlpool hasnt recalled the faulty part even though everything Ive read says it should be a recall.Its now taken over a month to get a repair person in to fix it. From the time we called Maytag, to the referral to the service person, to the service appointment, to waiting over 2 weeks for the part to come in, its been over a month with no washer. This is unacceptable Maytag! The repair company is finally showing up tomorrow only after 3 left messages from us.Either build a better washer or stock your replacement parts with the local repair companies and you should be reimbursing your customers whove spent a lot of money at the laundromat after spending between $700 and $900 on your washing machines.

I purchased a Maytag made by Whirlpool in China about two years ago. The timer went out about nine months later. It went out again about 3 months after that and I paid to replace two sensors in addition. The washer still stops during a cycle at various times; it might be pausing or spinning or filling. When it finishes washing, sometimes it refills and leaves everything wet. I purchased from Deweys in San Clemente and they have tried to service but this is a real lemon. I will never buy anything again made by Whirlpool. I will research and find out what companies have been bought by them so as to avoid this. I note online that there are several hundred complaint problems about Whirlpool so they had to buy a company with a good reputation and ruin their product.

I have always heard Maytag was one of the best so after replacing too many washers to count in 15 years, like Whirlpool and Kenmore, I decided to spend more for quality. I figured pay a few hundred more once rather than spending $400 for a cheaper one that only lasts 3 or 4 years. That choice seemed environmentally responsible and financially as well. However, I couldnt have been more wrong. In 2016 I purchased the Maytag Centennial top loader for $500. I really loved the size of the tub and the way it looked. I can fit a large comforter in it with plenty of room leftover. I also have no interest in a front loader after reading reviews. So I thought this was going to be great! Well it hasnt been. It has broken 3 times. The circuit board twice and now the bearings are going out in the motor. I fixed it the first two times but now Im done. Im done with Maytag, Aka Whirlpool. I think it will be a Speed Queen for me now. Im hoping it wont be a dud also because they are pricey! It actually scares me to spend that kind of money. I have really lost my faith in most companies nowadays. Customer service and quality has gone out the window. I think about how much this impacts the environment! Its terrible that appliances only last a few years before they end up in the landfill.

I purchased the Maytag Neptune set in 2004 and was not informed there was a class action lawsuit and was never notified. When washer quit working, I called Maytag who sold me a $300 service contract. They came out and said they couldnt fix the washer and I needed to buy a new one. I paid a fortune for this piece of junk and now have to spend another $700 to get a new washer. I will never buy Maytag again. How can they get away with selling washers that are on recall and involved in a lawsuit?

We bought the Bravo XL set 11 months ago and the washer leaks all over the place.. Called Maytag and had the repairman show up. Upon arrival he told us these were the worst machines to buy and would never recommend to anyone. He also said that business has been great due to all of this.. He checked the washer and said the water pressure was too high and lowered it. He couldnt find anything wrong with it. After he left I started a load and sure enough it was the same. Called him right back and he said to call Maytag because he was going to another repair job. I called Maytag again and they said to call the repair guy.. Never again will we ever buy Maytag.

I wish I had seen these reviews before purchasing this machine. The plastic tub cracked and leaked all over laundry floor after only 30 loads. Part is unavailable. We will have to wait 3-6 weeks for a repair. Manufacturer will not agree to providing a new machine. Machine is only 3 months old.

Never had a better washing machine, highly recommend this product: MVWC425BW. Saved plenty on water usage, no rust and no service issues after 6 months.

Bought the Maytag MDSH969AWS1 in Dec. 2010, and it quit after 4 and 1/2 years. Ironically, replaced a perfectly good 20 year old GE model that ran great for this piece of junk. I tried to diagnose the problem: the washer fills, but when the cycle is supposed to start it just hums. Then you have to drain it. So I think the problem is the motor or capacitor. The parts are stupidly overpriced, and Im not even sure if that is the problem. It could also be the electronics board (Ive heard of the problems with these on this brand). So instead of risking wasted time and parts Im junking this, er, piece of junk. The stainless steel door was rusting on the bottom too. American made crap! Bought a fancy Samsung to replace it, and will NEVER buy Maytag again. Im old enough to recall the lonely Maytag repairman -- Itd give him a swift kick in the rear for being associated with such a shoddy brand. Maytag, its the Dodge-Jeep of appliances.

In 2011, we purchased this Maytag Centennial MVWC200XW1 washer. It will not complete the cycle when it goes into rinse and spin, will not empty water and once the cycle starts, it sounds like someone is inside with a hammer banging on the basket. Clothes come out with a powder residue on them and several pieces have had holes. Called Maytag and was told there was no service available in our area. I will never purchase another Maytag product. Used by two adults a couple of times a week, this machine should be trashed. I have to hand-wring our laundry as we cannot afford to replace at this point. My last washer was a GE and I had it for over 20 years, we replaced it because we moved into a new home thinking Maytag was the best out there. I checked for a recall because there are so many complaints on other sites but found none. We purchased from Home Depot and of course, they are no help.

Since day one, no matter the size of the load or how careful I place the clothes or what level or water, washer vibrates and moves around the floor. I have had service out twice to recheck level but it still vibrates. Worst washer ever. I should have spent the money to repair my 20-year-old Kenmore.

We purchased a Maytag Bravos Automatic Washer 6/28/09. The interior enamel around the bleach dispenser started rusting about six months ago and it’s getting worse. Our white clothes are getting rust stains on them. Otherwise the machine works well, but what a huge flaw. We will buy a new machine, but not a Maytag.

I had another Maytag washer. It lasted 21 months. BB got me the BravosXL to replace it. I have had it 6 years. It is a piece of junk. Goes out of balance all the time. We are 2 ladies and don’t have heavy clothes to wash. I am washing now. I have put It through a wash cycle. The soap is still on the clothes. I am on my THIRD rinse cycle and there is still soap on the clothes. And I used less soap. Never again MAYTAG.

Buy this washer! It has the best features! No matter what the setting, your clothes will come out as dirty as you put them in, only with even more odor! I just cannot believe how many different settings they managed to program into this washer, each one delivering the same miserable results. I am so happy that I spent so much money on a washing machine, that in some cases, doesnt even get my clothes wet. Truly amazing technology!

Theres nothing at all good about this machine. It is impossible to work with. Ive hated it since the day I got it. Dont buy it, ever, ever, ever. You cant put additional items in once its started, you cant adjust a load thats uneven and get it to complete a cycle, it takes forever to do one wash and it often rinses multiple times and theres no way to stop it. I HATE THIS MACHINE. HATE IT. LIKE ITS A PERSON. HATE. Is that clear enough?

Im not sure that the guys who designed this unit ever actually tested it. During the wash cycle, if you have something like a fitted sheet it will actually stuff all of the surrounding wash items into the sheet until it forms one huge, round ball. Then it gets really interesting because the vicious spin cycle sends the machine marching around the laundry room and this happens even if the wash has not balled up. I now try to evenly distribute the wash within the tub prior to starting the wash cycle but it doesnt work. So now I grab a cup of coffee and newspaper and sit with my washer throughout the entire spin cycle to make sure that the hoses dont tear out of the wall.

The door is worthless. I am the only washing machine user in my home and am gentle with my appliances. However over normal use, the washers door has cracked and has had to be replaced twice since it was purchased from Home Depot.

I have owned my Maytag washer for approximately five years. Ive always used the recommended detergent and religiously used the tabs to clean the machine when it was required. I have never abused the machine by overloading it, using too much detergent, etc. It is now coming up with an LF code. There is no one in this area who does repairs and if I do find someone Im sure theyll want some exorbitant amount to come all the way out to the boonies to give an estimate and the repairs Im sure will be hefty. I take very good care of all my appliances and expected this machine to last much longer.

I hoped the Maytag Maxima would compare to my old Maytag Neptune and it didnt even come close. Very disappointed. Doesnt fill with enough water to even WET the towels and doesnt rinse any of the soap out of the clothes. Been using it since 12/2015. Hate the Maxima. I looked for the brand (Maytag Neptune) which I couldnt find. Settled on the Maytag Maxima which is a complete bust. The Maxima doesnt fill with enough water so Ive had to add water to both the wash and rinse cycles. It has also become very noisy. The repairman has already stated that there is nothing he can do about the lack of water since the amount of water is set in the factory and cannot be changed. The Maytag Maxima is a complete bust for me! Its a front-loader that has me adding water (at least 2 gallons) to every load no matter how small. Wish Id bought a GE top-loader that Ive seen advertised.

My Maytag Bravos washer is 6 years old. I had to have the motor replaced about 2 years ago. Now, it gets stuck on uL on every spin cycle. I had a technician come, and was told its just cheaper to replace the machine at this point. What happened to the Maytag man of old, the one who never has any work to do because the machines are built so well?!

I bought a Maytag Bravos from Home Depot back for around $1000 in Nov. 07. After 3 yrs, the whole tub assembly had to be replaced but I had bought a warranty so that was taken care of but it was out of service for about 2 months while I waited for parts. Now every time I use it, I get the OL on the control panel and it wont spin without getting out of control and stopping. Washers in the past have lasted me at least 15 yrs and cost less than half that much. I will never buy another Maytag ever. This is what happens when companies merge and quality is no longer important. I think the stock market ruins companies. Im currently looking for the best quality, large capacity washer on the market. I will pay more for quality but thats what I thought last time.

Maytag top load 300 series washer - This is the worst washer I have owned! It does not wash items- especially sheets - without getting totally tangled up and twisted! I wish I had my old one back that lasted 20+ years. I will NEVER buy another.

I have owned this washer for three years and the smell in the entire area of my home is getting unbearable. I have used vinegar, clorox, and washer cleaner and I always leave the door open when the washer is not in use. My other complaint is that even a small amount of bleach cannot be used on clothes without causing bleach stains because it runs directly on the clothes before enough water is in the washer. The receptacle for softener also does not dispense the softener properly. I am very disappointed in this machine.

Maytag Bravos XL: I purchased mine Nov. 9 2017. I so wish I had never bought this machine! It leaves soap residue and dog hair on my clothes and bedding. I have to wash everything 2-4 times. It’s beyond disappointing. My husband and I agree our clothes looked better dirty, BEFORE we “washed” them in this machine.

I love my Maytag washing machine. It have different settings for the wash, also a size load for your washing, and I love the rain cycle. You could do single runs with Downy or extra runs which is great. Especially great if you’re doing blankets and towels you need that extra rains. Great reliable machine. Highly recommended.

Bought this Maytag Bravos Washer online from Lowe’s in the holiday season of December 2017 because my previous Maytag HE washer broke after 17 years. I have had nothing but issues with this washer right from the start. The clothes do not come clean as I find myself putting them through the wash cycle two or three times to have them washed and come somewhat clean. The clothes come out soaking wet that I have to put them through the rinse and spin cycle at least one or two more times. I called Lowe’s to complain about this washer and they said they only have a 30 day return policy and they would be happy to call for service for me. I told them it didn’t work from the start but they didn’t care. So now, sadly, I have a repairman coming this week to fix my new washer, And hopefully he can fix it that I can use it and it can properly wash clothes. I wish I would have her read the reviews on Consumer Affairs about this washer before purchasing this Maytag. Not happy with Maytag. I would have never bought it and bought a different brand. Codes appear on the face of the washer better. Nowhere in the manual that I had to personally download myself because it didn’t come with one. And oh did I mention that I need a step ladder to reach into the bottom of the tub? This washer should come yellow because it is definitely a lemon!

It doesnt agitate enough to move clothes around. Doesnt put enough water in tub, even on deep fill just barely gets to the top of clothes. Washed a shirt 3 times by myself to get dried mud off of it. 3 time it was washed bumy its self. Clothes do not to get as clean as they did in the old style washers that had good agitation and the agitator that was bigger than whats in these new ones. And water. Need water. We arent trying to dry clean. And even thats done with a liquid that totally covers clothes and moves around better than this garbage I have right now... Looking for an old washer to replace this one... HATE HATE HATE THIS WASHER.

I live alone and bought this unit for long life. After a few short not-used-much years, my washer sounded like a 747 was landing in my laundry room. I am a maintenance person, so I did a bit of troubleshooting and narrowed it down to the bearings installed in plastic on the outer tub that failed. My cost was $600.00 to $750.00, parts alone. It still worked, just very noisy on high spin.I emailed Maytag (now Whirlpool) and was phoned by Lee Ann. I told her I had all Maytag appliances in my home and was laid off and that if after the use this washer has had and it will cost this much if I do the work, I was not impressed with this company. She apologized and told me she will issue me an extended warranty for $299.00 that will cover it. I told her that without a job, I cannot make a decision so fast. She gave me the next business day to decide. I concluded it was cheaper than the part, so I called her back. I was scheduled for a repair, and the man opened the front and looked at it and said it was an outer tub bearing. He went to his laptop in his truck and returned to tell me that they would not authorize that expense and that all they would authorize was $350.00. He put the front of the washer on, then as if he forgot something, took it back off and reached way in the back and did something. Then, he reinstalled the front. I was livid! They charged me $299.00 for a warranty and would not repair! So I called back and was hung up on. Next, I called my credit card and disputed the charge. I tried to use the washer, and it made funny sounds and then filled up my home with smoke and stopped working. I called Maytag again, and he denied the repairman would tell me how much they would authorize to repair it and told me good news that they would issue a $174.00 check. I gave $299.00, and a few days later, they give me $174.00? This is why Whirlpool is destined to fail. I will never buy again, and I will wash in my laundry tub first! This is exactly why imports will rule! So Whirlpool, you got me for the last time!

I have a top loader Maytag washing machine, Model MVWB835DW4, bought in 11/2019. Five months of light use, the lid cracked. Received a replacement and four months later the lid once again cracked in the exact same spot. Requested replacement parts under warranty and I was told that a service tech must install the lid. Due to health and safety concerns related to Covid, we are not take any chances letting people into our home. My wife and I are 70 years old and are at high risk. Maytags response was they would not send parts under warranty to me and a service tech must install the parts. If I dont let them in by 11/2/2020 (the end of the warranty period) then I would have to pay for the parts. Maytag has the very worse customer service in the industry.

We bought a Maytag Centennial Washer in 2011. 6 months ago the control board went bad. Maytag has an exorbitant replacement price! I went to Ebay and bought a NEW board for 1/7th of the price Maytag wanted. The old board was marked revision B. The new board is revision F! That indicates to me that the board was defective when it was new and they have made 5 attempts since then to fix it! No recalls however. Now the motor is shot. I found out the motor from Australia is also inferior! So this 5 year 3 month old POS Maytag is going to the dump! We will shop for something made outside the US. No not a Samsung. I think there should be a class action suit against Maytag.

I bought a Maytag Centennial Commercial washer, 3.8 cubic feet, Model # MVWC425BW on September 17, 2014. My clothes were never clean and barely wet. The machine took almost 2 hours to do a load of clothes and they werent even clean! I bought the 3-year extended warranty through Lowe’s. Three years and 8 days later the machine stopped working. Serviceman came out and told me the washer was fatally wounded. He said the transmission failed. He also told me the replacement part would be $400.00 and that it wasnt worth it. He said these machines are junk and Maytag has had all kinds of issues with them. So Maytag knows these machines fail and yet do nothing for their consumers. Maytag, you will only ride on your name for so long; consumers are catching on. Maybe back in my Moms day you were the go-to brand but Im afraid that ship has sailed. Ive always gone with Maytag but now I question that choice. I came on Consumer Affairs page to see what brand I could buy other than Maytag. Seems Kenmore gets high marks.

Love, love this washer. Does an amazing job cleaning colors, whites, and bulky bedding. If you like Tide Pods or other liquid pacs, this might not be the washer for you as they tend to end up inside the gasket. Powder-filled pacs are no problem however.

I purchased a Maytag Front-Loading Washing machine. It was purchased on 11/30/15. Approximately this January, 2017 the spin cycle stopped getting all the water out of the laundry. Towels came out wet, shirts came out wet and I tried washing a small bathroom rug that came out of the washer dripping with water. My husband called Maytag to tell them about this issue. They told him I didnt know how to load the washer machine. Wow, I have only been using washing machines for 45 years and now I dont know how to load a machine. Then they said they will send him a video to watch on how to load a washing machine. I watched it. I wasnt doing anything incorrectly. (Maybe someone should send them a video on how to build a proper washing machine.) I previously had a Maytag Neptune machine that lasted twenty years until there was a class action suit against the machine. The clothes came out fine from that machine. I just purchased an Electrolux front loader that works beautifully. Now I have a Maytag machine that is nothing but a piece of junk in my opinion. It cost $824.21. I will never buy a Maytag machine EVER. MHW7100DW.