I have the same problem Judy had last week. I have a 36 inch under counter oven. I use it all the time. I have had it for about 10yrs. In the last year the computer has been replaced 3 time. The first time it cost me $600.00. 6wks later it was replaced for free. Now the oven is having the same problem. I hope Dacor makes me as happy as Judy.

Two years ago, we redid our total kitchen at considerable expense. All of the appliances we replaced were made by Dacor. They included: 1) a 36-inch refrigerator model EF 36/wf; 2) a dual wall oven, model EO230SCH; 3) a gas cook top, Model RGC304; 4) a dishwasher, ModelEDWH24S and; 5) a range hood, ModelEH3012SCH. The problems started within a two months of installation. The refrigerator stopped running due to a relay failure and a compressor problem; both were replaced by Dacor at no cost to us. It was inconvenient but not costly. A short time later, the lower wall oven stopped working as well as the lights in both ovens. This required the replacement of the main control panel (control circuit board). Dacor paid to have it repaired. The clock does not keep accurate time and gains about an hour a day. We decided to leave it well enough alone and did not have it fixed. After the one-year warranty expired, the lower oven quit again. This time, it had to be removed from the wall and an exhaust fan in the lower oven was defective and had to be replaced. Dacor’s initial response was it was out of warranty, so it was up to me to cover repairs. They eventually agreed to supply the part (about $90) but we had to spend several hundred dollars to install. Now, the lower oven takes an extremely long time to heat up, and again we decided to leave it well enough alone. Recently, there was a loud flash in the vent hood; one of the bulbs apparently burned out. My wife tried to turn off the lights in the hood but the light switch apparently blew when the light went and could not turn them off. After a couple of burned fingers and a melted bulb removal tool, I managed to get the other bulb out. A call to Dacor got the usual out of warranty response. I called the local Dacor authorized service rep. He looked at the problem ($95) and said he would have to call Dacor. After he talked to Dacor, they called me and said they would send a replacement control board but would not pay for the service calls. The service company said the next service call would be $195. One light bulb burned out: cost $290. I suspect that every hood unit that Dacor made with this control board is also defective. We have had to replace the halogen bulbs with great regularity. We have halogen bulbs in our boat that have lasted at least 15 years. There was another complaint on this board that had a similar problem with the vent hood. He decided to fix it himself. He is an Electrical Engineer his comments are worth reading and speak to the inadequate design of this unit. It is a shame that the Dacor appliances appear to be near the bottom in terms of reliability. Consumer Reports that their gas cook tops appear to be the least reliable. It looks like I have something to look forward to. Needless to say, I cannot recommend Dacor to anyone. In fact, I would recommend that they not purchase any Dacor product that does not have a full multi-year warranty.

Oh how I wish I never bought a Dacor! It has been nothing but problems. I figured I bought a lemon but after reading other reviews its just not a good product with not very good customer service either. I have had repairs every year, and even after repairs it still isnt functioning as it should. The first problem I had was the whole glass window blew out during baking, which seems to me is a huge liability. The company said that shouldnt happen but is out of warranty and would give me a discount on the glass. I thought that was better than nothing but then 6 months later the relay went out, then baking temps were all over the place in the oven so they said I needed a new motherboard and they said both ovens needed it. So those were repaired. Oh ya and the light in the bigger oven hasnt worked past the first year even after having the light changed and some electrical stuff done on it. Then I had the bulbs changed due to irregular oven temps. The temps are still all over the place to this day.The back right corner gets too dark. The front left doesnt brown and is a lower temp. Now Im having problems with the oven turning off during baking and when using broil in the small oven it causes the large ovens probe alarm to go on and offer at least for an hour. Dacor didnt help me with anything past the glass and its only been 7 months since the new motherboards were put in. I cant afford to buy a new oven at this time and so I only use the small oven mainly since the larger has so many problems. Do yourself a favor and never buy a Dacor!

DCT305SNGH - I have owned this stove for about 3 years already. From the very beginning it has been trouble. The lights that turn on when a burner is on broke immediately. The place where the gas comes out and ignites is black and hard to clean. The grates are rusty, the finish has come off. The indicator knobs dont reflect what is happening in other words if it is on the lowest setting you dont have any indicator marking. It is hard to clean and scratches very easily. I have had the service person out about 5 times until they decided to send me many new parts. These arent any better. It is just a bad product. Basically the warranty is useless if you keep calling for the same issue. They say, This is the last time we will fix this issue. Sadly I always heard this was a great company and I waited 7 years to save up for this stove and boom rotten appliance.

Bought the DACOR WALL OVEN in late 2019. Top burner is over heating and burns everything, caused a fire in the oven. Can not even get any response from customer service. Warranty not worth the paper it is printed on. Stay away from DACOR.

Follow-up to March 31 posting: In 2001, we installed two Dacor wall ovens and a gas (converted to propane) cook top. The cook top has been problem free and the brushed stainless steel surface still looks like new. Both ovens however, at that time, were problematic during the two year-warranty period. Knowledgeable service people were hard to come by in our region. After numerous service calls, Dacor replaced one of my wall ovens at or around the three-year mark (outside of the warranty period). That particular unit had only one minor issue since then and Dacor replaced the appropriate part free of charge. The other original unit has been problematic since the beginning. The latest problem being the internal light going on/off for no reason and then a lack of response to light button on the front control panel.Long story short, I posted my frustration here on March 31 and was contacted by a Dacor rep within two days. He asked me for detailed info on the problem and located the unit in their files. Some of the past repairs were known to Dacor, but others were not since we just did them ourselves. I was asked to send a detailed description of the current issue along with pictures, which I did. Based on Dacors analysis or the pictures and the exhibited problem, they sent me, free of charge, a control panel membrane, a door gasket and a set of door hinges. We installed these items and the unit is now in full working order.In looking back over the past years of problems with this particular unit, its clear to me the issues all stemmed from an original broken door hinge. It was compounded by the fact that the service and repair folks at the time considered the door gap to be within tolerance and we did not discover the broken hinge until the door glass shattered and we needed to replace it, which required removing the door. Anyway, at this stage in the game, I am very pleased with Dacors response. It is my impression that they are trying much, much harder to stand behind their products. So, while just a short time ago I would have never considered another Dacor product, when the time comes, they would still be on my list of considered vendors because when these ovens work, they work great.

I have a Dacor MORS130SS oven that I purchased in July of 2008. After 6 months the first membrane panel failed, one year later the second membrane failed. One year later the third membrane failed. Im on the fourth membrane and now my fine Dacor is burning things!! I can set the temp to 350 and it shows 350 on the display but the lower element never shuts off and whatever I cook gets burned. I bought this oven thinking it might be my last considering the supposed quality of Dacor. I know for sure it wont be my last oven!! I sell appliances and I never recommend Dacor ovens because of all the continued problems. Ive never used the self clean feature since being told by a Dacor tech trainer that he didnt recommend using self clean because it would cause the oven to age faster. Wonder how long it would have lasted if I did use self clean? Sure wish Dacor would contact me for a testimonial!

Dacors wall oven wont heat up after I used Self Clean feature. Dacor said there is a reset button behind exhaust frame on oven (close to door latch). I called when I could not find red button and was told it was hard to find and they did not know exactly where it was located. Maybe I should call repairman. Any suggestions? Has anyone else had problems after cleaning oven? PS: My 5 year extended insurance expired Nov 11.

This will be the third service call on my Dacor Built-in Refrigerator with the freezer making icicles and the fan making a loud noise. On top of that, I have two light bulbs in the freezer that went out from the ordeal. From my review of the complaints here on Consumer Affairs, I see Im not the only one with this issue. This is a yearly problem, and I hope Dacor would step up and resolve this for me since it truly is a poor design issue and no fault of mine.

Would highly recommend not spending the money on Dacor. We spent big money on our kitchen hoping for years of trouble free service. We can no longer get parts for our Dacor gas stove/electric oven. The burners click for 2 minutes when you start them. We have gone thru 5 circuit boards. NO LONGER AVAILABLE. The oven light goes on and off by itself. Etc. Etc.

Dacor ERD30S06CHLP 30 Inch Epicure Series Freestanding Dual-Fuel - I am so dissatisfied with this product. We bought the first range in 2003 and were so excited to use it. We chose Dacor over Wolf. From the beginning we had issues with the oven. It cooked very unevenly and the door never closed properly. We had a service call and they basically told us that we got a lemon. They offered us a new range for $3.5K. We thought we got a lemon so we agreed and paid for a new one for $3.5k. We also purchased the extended warranty for $2.2K.0 This one was even worse.One time I opened the oven and it burned my eyelashes. I wrote and complained with a video of the explosion and had to pay for the service call. I wrote a review in the website and they deleted it. We now own a range that we have paid over $10K that bakes unevenly, electric element does not work in oven and have minor explosions from time to time with a door that does not close. We have a few friends who have asked us about our range and we always recommend against it. We are looking for a new range. I would not recommend this range. I thought we got a lemon. But it seems thats just the product.

I remodeled my kitchen about four years ago with all Dacor appliances. It was the biggest mistake I have ever made. I have since replaced the refrigerator after only two years. After spending over $1000 in repair calls and parts, I purchased a new refrigerator as the freezer motor went out and had water all over my floor countless times even after new parts were installed. The ovens also have been replaced (12 months ago) as the lower heating element went out and had the upper and lower ovens go out with panel failures. I was so stupid to install the 30-inch dishwasher, as well. It also went out after 18 months with a motherboard failure. The upper rack glider also fell apart. Having the 30- inch dishwasher, I would have had to have a carpenter come in and make adjustments to my new cabinets. So I found another 30-inch Dacor dishwasher at an appliance store in Memphis, had it shipped to me and installed. It has been 10 months and I am now having the same problem I had with the previous Dacor dishwasher. It never ends! With the only option left but to have the cabinet remodeled, I will be purchasing a third dishwasher 10 months later. The only good that came out of this is the cooktop is still working (as of this date). All I can say is, if it says Dacor, dont purchase the product! This company shouldnt even be in business! What is even more pathetic is, when you call the Customer Service number, their representatives have such a I could care less attitude. It is a waste of time to even attempt to seek a solution to your problem. I guess they feel that since they have your money now, its the consumers problem, not theirs.GE Profile products are far superior and a lot less money. It goes to show an expensive price tag doesnt mean the product is superior.

We are in the process of remodeling our house including an entire new kitchen that we cant wait to finish to invite people over and show. HOWEVER, the cook top already has a light burned and finally the cover of it ended up falling as I was wiping down the stove (very softly by the way because I like to treat my appliances really nice). We have had this stove for less than a year I havent even made the last payment and it is already with a light burned out. REALLY? My husband spent countless hours researching the best appliances and decided to get this one and to come to find out that it is not good it is a complete disappointment. I am sooo upset. DO NOT BUY THIS BRAND!!! Save yourself the hassle that we are now going to go through trying to get a hold of someone on the phone and see what they will do if anything. I bought it from AJ Madison.

I purchased a Dacor range/oven combination in 2005 for a total kitchen remodel. I chose Dacor for its name and reputation for quality. The first problem was that the digital clock was running very fast; that occurred in October 2005 and was covered by the warranty. The next problem was that the downdraft would not stop going up and down. I had to turn off the breaker switch of that function until the repairman could fix it. The next problem I consider as a design flaw and not an oven malfunction. Both oven lights were burned out by June 2010 and needed replacing. The light bulb cover for my model is behind a grid for the oven racks which must be removed before the light can be accessed. It’s not a 5-minute job. The next problem was in September 2010 when the oven broiler refused to work. Another service call was needed to replace the oven broiler ignitor. The next problem was in June 2011, when the oven rack, which slides into cavities built into the rear wall of the oven, refused to release. It required another repair call. The repairman had to pull the oven out away from the wall and work to release the rack. As a result, I do not use that rack. Theres no one who uses the oven besides me; I have no kids in the house. The oven has never been misused or abused. The next problem was in November 2012, when the self cleaning feature refused to work; another repair call was needed. All of the above cost me $1,250. When I contacted Dacor about the myriad of problems/issues, I got a written reply that said every situation is reviewed on a case by case basis; in most out of warranty cases, Dacor would sell me the part I needed at a reduced price. I responded that would necessitate two service calls (one to diagnose, one to fix) and an inoperable oven for however long it would take to get the part and then reschedule the repairman. In almost all of the above, my repairman (Dacor authorized repairman) had the parts on his truck. I cant be waiting weeks without a functioning oven. Based on all of the above, my oven would have been out of order for many weeks. I wrote Dacor again, thinking the CEO needs to know about all these problems. I asked my contact to forward my correspondence to the CEO for review/comment. Instead, I got a reply from the customer service supervisor who stated in part on his 1/3/13 email, There tends to be a disproportionate amount of negative postings on-line”. Really? Most companies pay attention to complaints or compliments about their product or service. If someone takes the time to communicate, then the company owes its shareholders the duty to listen when there are repeated complaints about their product. Will I buy Dacor again? Never.

I contacted James ** at Dacor. His attitude was excellent and he resolved my problem (deteriorating dishwasher racks) beyond my expectations. He was compassionate and understanding every step of the way. James followed through on his promises in a swift and efficient manner. I would recommend Dacor and James ** to anyone. He is an asset to Dacor and should be recognized for his professionalism.

I wrote yesterday, perhaps a little too hastily that our motherboard was dead on our Dacor stove. The repairman came today and fixed it by removing it from the front of the stove and unplugging two plugs and plugging them back in. Everything works fine now and we are vastly relieved. The repairman commented that most people are very happy with their Dacor appliances and he doesnt repair them very often.Total relief. Also hope this doesnt happen again because though extremely simple to repair, it would become very tiresome to remove the motherboard and fiddle with the sophisticated circuitry if we had to do it ourselves. I wasnt watching real closely what the guy did and dont know if I could do it myself.

Our new ranch has three Dacor microwaves, only one of which has had a few months of use. The others have very limited use. To this point weve not had problems, but given the opportunity to redo the purchases wed go with a popular brand, i.e., LG, GE, Panasonic. They are more flexible, parts are available, and all three combined would probably cost less than one of these. In fairness, I personally feel the same about our other high end appliances, Wolf, Viking, Sub-Zero and Asko. None beats our former appliances. Maybe its just about show.

We have a Dacor Epicure 36 six burner range. It has been a regular source of trouble since it was installed as part of a kitchen remodel in 2006. The igniter for the broiler went out 18-24 months after we got the oven. A year or so after that the weld that holds the bottom oven rack bracket to the oven itself popped loose making it impossible to use the lowest rack position in the oven. Last year the circuit board that controls, among other things, turning the bottom oven element on stopped working. Not only is the board itself quite expensive, but it is buried deep under the top of the stove taking lots of expensive hours of repair time to remove and replace. And now the burner igniters have begun to over spark (e.g., continue to click long after the burner has been lit, burners sparking that have not been turned on). The repairman tells me that is a different circuit board so we could be heading to another $500 or so in repair bills or perhaps a trip to the dump and a much cheaper replacement range. We have had other Dacor equipment (cooktop, wall oven, warming drawer) and have not had a problem with any of them. But given our experience with the Epicure I cant imagine ever buying another.

We purchased the modernist collections 48” range, refrigerator and freezer, oven and microwave combo and dishwasher with a kitchen remodel 9 months ago. We had one issue with the dishwasher which was resolved, then another when is stopped mid-cycle. Repairman came out and was told we needed a new panel. Found out it was back-ordered. Well, it’s now been FOUR month without a dishwasher. We have contacted customer service and asked for other options and were told there was nothing they could do! When following up we have left messages and had our calls not returned, as has our service company. I have waited on the phone 3 times 30 minutes to talk to someone, because they won’t call back. We’ve asked to talk to a supervisor, and was told our information would be forwarded... 2 days later, no call. This is by far the WORST service I have ever had for ANY type of product.

We purchased a home with a 5 year old Dacor Discovery IQ Double Wall Oven. Model Number DYO230S. Great looking and it has a very sophisticated and functionally rich digital control system. Problem is the digital control system does not work. The stove has a mind of its own and will just shut off for 24 to 48 hours and return to function randomly. Shutting the power off and turning it back on has no effect. Dacor (Now Samsung) has been completely un-helpful. Bottom line response - tough. Product is no longer produced, replacement parts no longer in stock - maybe there is a part on eBay ** Honest that is the answer. I have called parts companies who also complain about Dacor (now Samsung). No luck. So we will now need to purchase a replacement product for anywhere from 4,000 to 10,000 dollars. To replace a 5 year old - 8,000 product. It will definitely not be a Dacor or Samsung product. And I will do my best to put similar reviews on the internet where ever I can.Just to add some balance - 21 years ago we custom built a home and purchased two Dacor ovens. Both were great. 21 years of flawless operation. When we saw this oven as we went through the home purchase process we were delighted. What a disappointment. Also - before the oven started to go wacky on us we needed to replace the bulbs (2) in the oven light fixture. Initially I contacted Dacor parts and had a very pleasant experience ordering the two replacements. However nothing came to our home. Called again and found that Dacor had been sold to Samsung and the price of the bulbs had doubled or more. No exaggeration. Stay away from Dacor and Samsung.

48 in. Range - Wish I had read reviews first would NEVER have purchased Dacor. Paid almost 11,000.00 for a range so many issues they replaced it. New range came with 7 defects. It has been over a month and nothing has been done about it. Everyone keeps passing the buck and I am sitting with an high end expensive product and no help from Dacor. I am being very patient but also very frustrated at this point.

When I pay top-dollars for a supposedly high-end product, I would expect performance and durability. That is not the case with Dacor. This manufacturer charges top-dollars for their appliances but their products do not live up to expectations. I purchased a Dacor gas cooktop range, and within a year several blue-indicator lights on the knobs (which indicate the gas is on) failed. At that time it was covered under warranty, and even then it was a hassle to get the repair technician to come out and take the range out to get to the electronic parts. After replacing two of the lights, the other lights failed as well, and then the replaced lights eventually went out. Now, only one out of the five lights work. After a year, the appliance is no longer under warranty, and it is too expensive to get it serviced. Its not only a cosmetic issue, but a safety one as well.Were in the market for a single wall-oven, and I considered a Dacor for its clean and stylish design. However, after reading the reviews about Dacor, Im veering away from this company. Sadly, as much as I want to support a Made in America company, the pride of workmanship and customer service doesnt live up to this companys branding.

Over ten years of using my Dacor oven, I have spent $1595 in repair bills to keep it going. It cost $1875 originally and I would have purchased a more reliable brand if I had known how much trouble the oven would cause me.

I have had nothing but trouble with a wall oven I bought in 2010. Basically just bad electronics. I finally replaced the oven in 2014 and had to get another Dacor to fit the opening. The new unit still does not heat evenly and is consistently off by about 50 degrees. Customer service is not helpful at all. Local repair shops cant really fix issues. Terrible company. Cant figure out how they stay in business.

We remodeled our kitchen because my wife is a chef. So we thought a full suite of Dacor products was just what she needed. What a mistake! Our $6000 36-inch dual-fuel range had problems from the start. We had to replace the control panel, heating element, convection fan, and door seal. Finally, the liner split and the range became unrepairable. We made the mistake of purchasing a simpler, gas-only range because Dacor offered a modest discount. This $7000 range lasted four months before a failure in the wiring harness made it unrepairable!! We bought a Miele replacement. We have had performance issues with our Dacor warming drawer and microwave. DO NOT BUY ANYTHING DACOR!!!

I was very upset when I tried to get service on my Dacor range. I made a complaint to ConsumerAffairs.com and was subsequently contacted by James ** of Dacor Customer Service. He offered a telephone number to support a local appliance repairman and arranged for me to get my parts at a special pricing. This worked out great and my range is now fixed. I am a happy Dacor Range owner now. It was just too bad that I had to make a complaint on the internet before I got help. I hope this incident will encourage increased cooperation from Dacor in the future.

As I have read in most of the reviews, we have also experienced the control panel on our 30 inch dual range cracking over the years. We were told not to replace it because it would continue to happen. Ok, lived with that... Now something new has started to happen, the plastic handle on the oven door and surrounding area has started to melt. It got so bad after a self clean that it is collapsing. Now there isn’t much of a seal at all when the door closes. The stove isn’t brand new, but this has to be a fire hazard, and consequently, now the oven will not even turn on. I’ve reached out to Dacor with no response yet. I’m done with this company!

Purchased home with installed Dacor double oven. Oven wouldnt reach set temperature, so replaced control board. Doable, but a real hassle to remove oven from wall opening and label, disconnect, and reconnect 20-something wires. Two years later, the clock cannot take the correct time and oven timers do not work. Only fix: replacing the $300 control board again. I cannot recommend that anyone purchase these appliances as the control boards simply do not work for more than a couple of years.

I purchased a Dacor Renaissance range for our new home. What a waste of money. Though I have not had any major problems with the performance of the range yet, besides uneven baking, the design is not user-friendly. To begin with, the gas burners share a grate. So when cleaning, you have to remove the whole grate on one side. The controls for the burners & griddle are very hard to see & I have to bend over to see which burner Im turning on. The oven racks are a joke. The two glide racks are very bulky with sharp edges. It is difficult to change the heights or to remove them for cleaning purposes. Though there are three racks included, it is impossible to bake with all three in the oven.I have a GE Monogram that I had purchased two years ago for another home, and I love it The Renaissance & Monogram are similar in price, but I unfortunately, listened to the sales person & let them talk me into the Renaissance. I realized my mistake in buying a Dacor immediately & contacted the appliance store. Even though the Renaissance had not been used, they would only give me a token amount of money towards trading it in for a Monogram. So, I am stuck with a range that causes me to swear under my breath every time I use it. Dacor could learn a lot from GE.

We have a new (one year old) home with Dacor appliances. The microwave oven went on the blink the first month but was repaired by a factory approved repairman. Something to do with the computer. Now the double oven will not hold a temperature. We set the oven at 420 and it only goes to 360 even though the readout shows 420. We just decided to skip the repair process and bought a new Wolf oven. This is our second Dacor within the past two years and both have had the same problem. Dont waste your money.

We purchased this unit 7 years ago, just a family of two with visiting grandchildren. Unit came, had a crooked door and a bent latch, which we had serviced and supposedly corrected. When self cleaning the latch still made grinding noises. Over a year ago the oven stopped working period. A December service call said needs a new latch, sensor and display -we are now in 4 figures($). Oven operates for month and a half. January 2019 Service call now new door latch, relay board and main wire harness 4 figures again double! Oven stops working yesterday (June). Service call today new latch, motherboard and something else and another 4 figure repair cost. Same repair parts same problem! Patience is a virtue, but repair costs are sinful! Next step, Boat Anchor! Problem from the beginning and still a problem now.

I own a complete Dacor Kitchen, with many appliances. They are the highlights of my Home. Great features: fast induction cooktop with an efficient silent hood, versatile refrigerator, reliable oven, and of course the always dependable dishwasher. This is My Dacor Kitchen!

Our dacor appliances are 8 years old. Four or five times a year we need to have the technician to come by to fix something in our kitchen, dishwasher, built in fan for our stove top or refrigerator. These items are high price items-- should not have so many problems.

I have been getting the run around from Dacor regarding a part that I paid $700 to fix an interior light that comes on and off like a strobe light. After the local service company installed the part, recommended as the fix by Dacor, the issue returned. I contacted the technician again and that is when the run around started by Dacor. I was told to contact the customer service line and tell my story which I did, only to be told that the Range is too old and they dont stand behind the warranty nor service anymore. They said beyond 5 years they dont do anything for the customer.I paid $8000 for this range back in 2005 and it has worked just great until this recent issue. If I had known that there was no service nor any parts for the fix I would have just dismantled the interior light. But why did they recommend the part I did purchase to begin with? Are they just trying to increase revenues by advising customers to buy parts that wont work? DO NOT BUY DACOR PRODUCTS UNLESS YOU WANT TO BE ON THE HOOK FOR REPAIRS AFTER ONLY 5 YEARS! This company has rude customer service agents and they do not stand behind their name!

This is a follow-up to my prior comments on the 30 Dacor wall oven. After posting the prior complaint, a Dacor customer service representative emailed me immediately the following day asking for details on the problem. The Dacor rep immediately called my repairman, notified me that they were working on a solution, and then followed up with a solution that exceeded my expectations. We are very satisfied with the outcome and should have called Dacor directly at the onset. Thank you Dacor!

I bought the refrigerator less than a year for over $4,000 and the vegetable drawer chipped. When I called Dacor, I was told that it was a cosmetic issue and was given a number to call and order the part. For a refrigerator less than a year and costing that much, I thought it should fall under its warranty. Another issue is the ice maker. It wont dispense ice and I have to always pull the ice bin and put it back in. The Dacor customer service said that its because air gets into the ice bin when I dispense ice and thats the solution. Once again, for such an expensive refrigerator under 1 year old, I would think customer service would be more customer oriented. Never again!

I purchased the Dacor panel ready refrigerator and freezer column 15 months ago. The refrigerator stopped cooling -- in 15 months! These were 8k each!!! It had now been over 2 months without a working refrigerator and no end in sight. I will never ever purchase one of their products again! They replaced the compressor and 3 days later it stopped cooling again. What a joke! DO NOT BUY DACOR!

We purchased this oven February 2009. On 6/7/11, we had to replace the touch pad assembly. On 12/16/13, we again had to replace the touch pad assembly with a cost of repair to this point of over $900.00. The over cost $2,395.00 when purchased. On 3/16/14, while on convection/bake the oven switched over to broil. On 3/20/14, a repairman came to the house. The condition did not replicate but the repairman, in conversation with Dacor, determined that the fix, if this should happen again, would require the replacement of the relay board and ERC control at a cost of $700.00. On 3/27/14, while on convection/bake, the oven switched over to broil. I called Dacor and was forced to leave a message.

The wall oven’s glass was damaged by a guest. Customer service at Dacor was exceptional. Within a day of advising Dacor’s customer service, I received a call from the service man and the replacement was installed the very next day. The service man was considerate by calling first and coming exactly when he said he would. He was very professional as he replaced the glass in a matter of minutes. I would choose Dacor again.

We did a total kitchen remodel and purchased Dacor appliances. Big mistake. Had to spend 500 on refrigerator repair (model EF36BNDFSS). Oven is off 25 degrees on temperature. The glass top for burners was defective. Would never purchase Dacor. Microwave front trim keeps coming off as well.

This is the second time I have purchased these appliances and unfortunately each one has been a great disappointment. I have spent enough in repair bills to almost purchase a warming drawer. Each one shuts down when the self clean button is turned on, and then I have to call a repairman out to recalibrate the oven to work each time I try to use the self clean. I was told by the last repairman that the life of the oven is greatly shortened if you the self clean mode. If this is the case, either fix it or take out this mode. After I had the oven about a year the oven door glass blew out, and this had to be replaced. The temperature in the oven is very unreliable in different areas of the oven and browns more on one side than the other... For the high end cost of these ovens, I would just as soon have a basic oven that works and does not go out every few months. What a waste of money I consider Dacor to be, and will never recommend it to anyone I know. I am in the personal shopping business and have my own company, but will tell my clients to be very aware of the high cost/low performance of Dacor products... On a scale of 1 to 10, Dacor gets a 1.

I first bought the low-end Dacor dual fuel range and overhead microwave oven. Within the time frame of 3 years, repairs to the stove cost over $2,500. The stove cost $1,800. Ever single piece of plastic on the stove cracked and had to be replaced multiple times. The microwaves handle cracked 6 times, twice in one week. The overhead trim, which is about 30 by 6 and heavy, fell off and hit me in the head while I was frying bacon. If it had hit the pan of hot grease, I would have been burned. I contacted Dacor and got the brush off. I contacted Fight Back with David Horowitz about the problem. Dacor called me back, bowing and scraping, and we came to an agreement that they would take back the stove and microwave and put the full cost towards an upgrade to their high end model. I am sure you think I was stupid but the stove cooked beautifully and I thought a stove with no plastic trim pieces would solve the problem. Wrong! The microwave control panel has gone out twice, each repair costing around $350. The handle broke 4 times but that was covered under warranty. The front control panel has died 3 times (another $350 each time). The broiler dies each time the self-clean is used and that has been fixed 3 or 4 times. Some computer board on the top of the stove has died (another $400). The enamel lining inside has cracked, crazed, chipped off and rusted. Now, the front control panel has died and so has the one on the microwave. Times are very tough for us now and I cant afford to get them fixed. I noticed that the front panel trim on the top of the microwave is starting to pop out again (plastic fatigue). Hopefully, it will fall off again while I am cooking and hit me in the head and knock some sense into me. If it does happen, I will take them to court.

I was and, I repeat, was a loyal Dacor customer. I gutted and rebuilt a kitchen 9 years ago and purchased a Dacor stovetop, oven and microwave. I remodeled my new house 5 years ago and again purchased Dacor stovetop, oven and microwave. Consumer reports provided favorable reviews of the appliances I purchased below.First red alert: The oven Model MORS130S and Microwave Model DCM 24S LED did not match. The microwave was green; oven was blue. The brochure was in black and white so there was no way of knowing that aesthetically they were a mismatch ... it was very sloppy(!) and very deceptive by Dacor. I mean when I waited weeks for my appliance order and the oven is already installed with a big fat ugly LED screen, what was I supposed to do, yank it out and start all over again? This was disappointing!Next, I was simmering chili on the stovetop (5 burner, gas) and, lo and behold, 18 flames started exiting through the turn knobs resulting in a meltdown. The gas was leaking through the tubes underneath the stovetop. I just happened to check the chili while I was gardening to watch the house almost burn down and btw, it was difficult to put out the flames because the natural gas was leaking under the unit. Seriously! I called customer service and they got hopping right out to fix the issue. This scared the heck out of me. It is negligent to have a product like that on the market.After about 13 months into the life of the Model MORS130S oven, the touch panel failed emitting a CO1 error message. I was told it was $140 to fix it and that the panel was defective, great quality there, Dacor. And the added joy to the CO1 error message is that the unit beeps intermittently all day and all night long unless the power to the oven is killed. Joy... now another issue - Model MORS130S oven LED lights are burning out. Seriously, what else will there be? Now its $175 for LED panel and another $100 to install by an authorized Dacor service man.So I called Dacor back again today because the LED light out was annoying me. They offered nothing. To be fair, my appliances are out of warranty but seriously, Dacor nearly burned my house down. They should be winning me back as a customer if they really cared about their customers and having long term repeat business. Never again, Dacor, never!

After 4 months our microwave exploded when we tried to bake 2 potatoes. Dacor has reviewed the situation and acknowledged the product was defective. 10 weeks later they keep saying the replacement is on the way but no one knows where it is. Dont buy dacor products.

I purchased a DACOR Discovery IQ Range one year ago Model # DYRP36DS/NG from an online authorized DACOR retailer. Here is a synopsis of the events Ive had with the range over the past 12 months: I took delivery of the Range in January of 2016 at my home under construction. I moved into the home in April 2016 which is when the Range was fist installed. In May I began to have problems with the unit, it would shut down during preheating, then reboot itself, sometimes it would just reboot itself randomly. I called DACOR customer support who told me that I needed to download the latest software version, which I did. Shortly thereafter, the Range again would shut down during cooking and go into a reboot cycle.I called DACOR again, they sent out a local service company. In June the technician came out and upgraded and re-installed the software. The problem continued, I contacted DACOR AGAIN, got the run around, etc... Escalated the problem. DACOR then determined the problem was in the internal circuit board which they arranged to shipped to local service company. The service company came out again, replaced the internal circuit board and attempted to upgrade the eProm, which didnt work. The Range was in a constant state of rebooting itself over and over and over again. The Technician left. Said nothing more he could do. I had to shut the power off so the unit would stop rebooting itself.I called DACOR AGAIN, I got a complete run around, they refused to do anything more. I finally was able to reach the V.P. of Customer Service. After a few conversations and investigation into the issues. She determined that the unit needed a new front controller panel. The panel was shipped to the local service company. The service company came out again and replaced the front controller panel. Its now November. Over Christmas, the unit began to shut off the oven randomly during cooking cycles, for no apparent reason. Over New Years, the oven was shutting off, flashing an error code and reboot! I called DACOR last week. They refuse to help because now it is out of warranty.Ive contacted the online retailer. Ive left messages at DACOR for the Service Manager and the V.P. of Service. NO RESPONSE. So this is how DACOR deals with servicing their high end appliances, keep trying to pretend to fix the lemon appliance until the anniversary date, and then they dont have to deal with their $9,000 piece of garbage high end range any longer. The consumer gets screwed and DACOR doesnt care in the least! DO NOT BUY an appliance from DACOR.

We purchased our range (Dacor Dual Fuel Range RSD30) in about 1997 thinking we had a good investment. We have replaced the bezel 5 times (the area that encloses the control area). Today the door glass has cracked. Whooppee! Merry Christmas! Each time I called about the bezel, I was told that they had a design flaw. The last time we had to replace the bezel and also pay for installation ourselves. We decided if this happened again, we would get rid of it. Well, it will be sooner than later as the oven glass has cracked. Needless to say, we are not return customers.

We bought this oven and had it installed a month ago. Id love to love it, but unfortunately I dont even like it. Immediately after installation I noticed the touchpad for the bottom oven didnt work. I called Dacor and spent quite a bit of time while someone did the standard is the power on run through. I was told someone would have to call me back in the morning, at 9 am. The next day at 10 am having not heard a word, I called back. I was given the option to be called back (you wont lose your place, and our first rep...) Great! Nope. Four hours later still nothing. I called back again. Someone answered quickly and after a short call arranged for a service person to come out in a few days.Fast forward a few days and the serviceman arrives. Hes clearly never seen this kind of oven. He calls Dacor and talks to their troubleshooting department. They decide the motherboard is bad and reorder. Well, its been 10 days. *crickets*. There is no sense of urgency... In fact nobody even seems to care that my $7500.00 oven doesnt work and the microwave literally cant even pop popcorn. I would expect the company to rush delivery of the part. If need be replace the whole oven and figure out what is wrong with the motherboard on your own time. What I didnt expect is for literally everyone involved in the process of choosing and buying the appliance to not be able to find a solution. I give my new oven 1 star out of 10, because it looks nice. Id rather have an oven that doesnt have a smart feature and actually works. FAIL Dacor.

We had our whole kitchen renovated and purchased Dacor appliances through Caplans Appliances. We purchased the appliances in the summer of 2019 and they were shipped shortly after. Since our kitchen was still under construction the appliances sat in our home. They were installed the second week of November. Two months ago, I woke up to a sucking noise from the dishwasher. The dishwasher had a code of LC. We removed the custom kick plate to realize that there was water damage. Dacor has been contacted on numerous occasions regarding this and the dishwasher continues to leak. We have had 5 service calls to house and the problem persists. The seal has been replaced twice in a 2 week period. The repair company HARGTA gives us a window and does not show up at that time causing me to sit around all day waiting for them and then some days having to cancel work. Dacor customer service continues to say the Regional Tech Manager will be the one to provide the resolution and we have not heard from them yet. The reviews on here clearly indicate that the dishwasher leaks. We are risking damaging our floors which were put in at the same of our renovation. Looking for a resolution ASAP. To those considering Dacor appliances do your research.

Replaced main board on top of oven because of oven light turning itself off and on endlessly. Cost was near 400 dollars with service call. Now, 2 years later, F1 beeping nonstop, and we have to turn power off to stop it. Last night, the beeping started at 3 am! I would never buy another Dacor oven. The Dacor microwave has never been able to pop popcorn. Now the carousel is failing to rotate. The only thing positive about Dacor is the styling.

I called customer service to ask general directions on how to remove the top of my oven range. The person answering the phone (01/23/2017 at 4:25 PM) would not let me talk to anyone in service. I asked him why, and are you ready for this? He said we cant talk to customer service for our own security.. No kidding. The idiot went on to try and tell me it was for my protection! After arguing further, I asked him to again connect me with a technician. He puts me on hold and comes back and says The technician said to call a service provider - unbelievable. I will NEVER buy a DACOR product again! What morons think they can sustain a business with this approach to service!

We bought 3 very expensive Dacor appliances when we built our home 12 years ago. They have been a total disappointment. The microwave was replaced after just a couple of years when it just stopped working properly - including needing to stop it by opening the door! The wall ovens have needed many minor repairs which have amounted to several hundred dollars after labor charges. I see on this post others have had to repair the hinges! Ours have been replaced twice! The broiler came loose and was hanging on one side. The internal light also goes on and off by itself - sometimes in quick succession. At times, it stays on and cannot be turned off by the light button but by banging the front of the oven! Ridiculous! The cooktop cooks very unevenly. It goes from simmer to boiling over. The ceramic material did not hold up very well either. It is supposed to clean easy. But there are spills that have left permanent stains and we will be replacing that as well. We have also had Customer Service tell us items have been discontinued so we have no choice but to replace these appliances since replacement parts cannot be purchased any longer. This is a warning to anyone considering Dacor - DONT WASTE YOUR MONEY! There are far better appliances out there!

I moved into a house that already had a Dacor unit in place. Within months, I discovered that I owned an oven that could be fixed by throwing the circuit breaker. Then, I learned about invisible hands that turned the 325 degree convection oven to a 500 degree broiler. The final act was having all three glass panes shatter and the control panel cracking as punishment for assuming that the oven cleaner on an expensive gourmet stove would function according to manufacturing standards. The repairman ordered replacement parts. He spoke with someone who was off shore so forget about Dacor being all American made. The wrong parts were sent. He has reordered. Meanwhile, I have been without an oven for two months. If this goes on, I am going to Home Depot and buying a Hotpoint or GE. It is the same price as replacement glass panels and the control panel.

My Dacor Preference 30 double wall oven (model PCD227R) was installed on 5-14-2004. On 12-31-2007, I replaced the upper oven high limit switch for cost $146.56. On 5-19-2010, I reset the lower oven high limit switch for cost $95.00. On 8-27-11, I replaced main control panel (Bezel Assembly), whose parts cost $271.10. On 12-14-2011, I replaced the main relay board for $214.02. On 1-16-2012, I replaced main relay board again, and it is under warranty. On 2-3-12, I replaced upper oven temperature sensor for $32.09. I am awaiting authorized Dacor service technician to calibrate both ovens.

Updated on 01/25/2021: After my review in December of 2020 I have continued to fight for a resolution with Dacor. Dacor appeared to be unable to resolve the issue and sent the issue to parent company Samsung. Samsung set up an appointment for repair then cancelled it saying parts were not available and that they would authorize a refund. I supplied the invoice and filled out all necessary documentation, including my banking information so they could wire the money. Today, a Samsung representative called and said I needed to talk to Dacor to finish the process, even though I was told everything was approved.I called Dacor and to no ones surprise they said this would have to be approved and only one person can make that decision and they are hard to get in touch with. Oh, and by the way, 10 days ago the second oven failed. Yes, the large oven that did not work when I purchased the unit. It was repaired in September and has already failed again. I now have a double oven Dacor range and neither works. This week begins my 10th week of fighting with Dacor for them to honor my warranty (again the unit was installed in August 2020) or refund the purchase price. At this point the range has been out of commission half the time I have owned it. I strongly suggest you heed the warnings here on this site. I wish I had listened.Original Review: On August 3, 2020 I purchased a 48 Dacor Gas Range. It was installed a couple of weeks later and the large oven did not work. It took better than a week for Dacors authorized service company to come out and diagnose the problem. The parts took another week to be shipped and then another week to have the repair made. It was a defective thermostat that was preventing the oven from igniting.Fast forward to November 24. In preparing for a big Thanksgiving, we turned on the small oven, only to find that it did not turn on. It had the exact symptom as the large over and would not ignite. I reached out by email to the agent at Dacor who had worked with me before, only to receive the below response: Thank you for contacting Dacor – We are no longer able to provide support by e-mail. Please contact us at U.S. Toll free: 833-353-5483 we are happy to provide personal support.Now begins the worst customer service experience of my lifetime. After opening a case, I have now talked with a dozen different agents and have yet to receive a resolution to my problem - a range that cost over $7,000 that did not work out of the box and has now failed again in a three-month period. I have spent hours on the phone and on hold and was eventually directed to Samsung on December 9 because Dacor could not get the parts. Samsung promised to refund the purchase price of the product is the parts did not come available by December 16.December 16 rolled around and now Dacor is saying that Samsung made the promise, but that they are different companies. Remember, Dacor directed me to Samsung and Samsung does own Dacor. I have been told that the parts for my oven are no longer available. After continuing to push the issue I am told that it is now in management review but that it may take 2 weeks for a decision on my case. It has now been nearly a month since I opened the case and I appear no closer to reaching a resolution on my failed Dacor range. I have asked to speak with a manager, but I keep being told this is not possible right now.I do believe that Dacor is in breach of their warranty. I have been more than reasonable in allowing them to remedy the situation. Since this was installed just over four months ago, it has been out of service in one of the two ovens for a total of 7 weeks. For anyone considering the purchase of a Dacor appliance, I strongly caution you to read the reviews on this site and other sites. If you are lucky and get an appliance that works and never fails, you might be happy. If you ever have to invoke your warranty you will hate your life. I regret that I did not heed the warnings. It is truly unbelievable to me that in 2020, any company can stay in business when they display such disregard for their customers. Be warned.

I recently upgraded my kitchen and had always heard that Dacor has been a reliable high end brand for kitchen appliances. Their refrigerators have a lot of space, and everything can be easily organized. All the appliances work as intended, and they also all look great. The stainless steel Dacor uses to make these appliances look smooth and clean, making it one of the most beautiful kitchen appliances I have ever owned. If you want a functioning kitchen with appliances that always look nice and shiny, then I would highly recommend Dacor.

I purchased my Dacor Epicure Range 8 years ago when I remodeled my kitchen. My other appliances were made by GE and Bosch. Ive had to service my GE appliances a couple of times in the last 8 years, but it is the Dacor that has given me the most grief and it was the most expensive appliance purchased. It has never been reliable with regard to convection baking. Initially I thought it was my inexperience with a convection oven. I read everything I could get my hands on and kept trying...after talking with a friend who does quite a bit of baking I realized its not me, its my oven. Then the real problems started. First it was the broiler/ignitor, next it was the membrane in the keypad. Two months later it was the relay board and this time it was the broiler/ignitor....Again! Started calling Dacor when the relay board went out because at this point I had spent $1,000 on repairs....after I had paid $4,000 for the range itself. For the last two repairs Dacor has paid for the parts, while I paid for the service call and labor. This has reduced the cost of my last two repairs by about 50%, which is very helpful. However, Im still very disappointed in the product. I spend a good deal of time in my kitchen and do quite a bit of baking, cooking, and canning. I thought that if I spent more money and bought a high-end appliance, it would serve me well. At the rate that Im going, I will need to purchase another range, unless I want to keep throwing money into repairs on this one, which I dont. I will not ever purchase (or recommend) another Dacor product again.

In 2013 we remodel our kitchen. I need a 30" stove and Dacor seem the right fit. I had problem with the igniter burning on that stove and some metal warp as well. They replaced the stove in 2015. I smell gas every time I turn oven on. Last Thanksgiving 2019 the stove stop working. I was told the igniter had burned out and had it replaced. I had repairman come twice because of smell and end January 2020 the stove stop working again. The repairman told me that a jet burner assembly was never installed this is why I smell gas after it is turn on. ** They said they will order the part. It's back order So I contact Dacor. First they told me it's back order then give me a supplier. If it was never installed in the unit shouldn't Dacor take care of it and soon.

Add me to the Dacor hate list. The $4300 oven installed in 2000 is now a whopping $6400. My motherboard #2 is broken and the glass on the door cracked which to me is a safety issue. This is a two adult, no kid household so figure. We use the oven about 7 times a year. My Dacor rangetop and hydraulic exhaust have both required service as well.

I purchased a Dacor refrigerator. I needed to order filters. I called Dacor and ordered paying $178 plus a $29 2nd day shipping. They sent the wrong filters. The invoice is right. Outside box is right but inside were two Whirlpool filters. I called and asked them to send return label to ship back and to send the right filters. Deidra, the manager in customer service, said No, you must return those filters and yes, you were sent the wrong filters. They will come back into our warehouse and we will then send out your new filters. I said I paid 2nd day because I needed them now. She suggested me paying for two more. Whatever. I told her to send return label and I will order somewhere else. I wish I would have seen 226 consumer complaints before ever ordering anything from them.

I have an older cooktop. Yes it is 15 years going strong but I have ran into a few issues where I know the repairs would be pricey but especially the parts. After talking to a few representatives, they truly want to help you. Nothing is free and I don’t expect it to be, but I am glad they they helped me get my cooktop back to functioning again. I hope someone finds this helpful before reading or writing bad reviews.

This is a follow-up to my initial complaint, which was posted on November 28, 2011, and an updated posting on December 27, concerning problems with our Dacor range. What we learned was that the local appliance shop that services Dacor quit working on Dacor appliances, so we were left with no repair company. We were contacted by the customer service representative from Dacor, who has been very diligent in working with us to find a solution.Yesterday, the Dacor regional service supervisor from Washington came to Casper to work on our oven, which is now totally functional. Pretty amazing customer service! He did share with us Dacors challenges in getting qualified local service companies, especially in smaller towns. I applaud Dacor for going the extra mile (1,000+ miles, to be more accurate) for us.

First six month, dishwasher rusted on the inside. Dacor gave us a less expensive in its place. First year, microwave was repaired five times. Microwave has a piece of wood to hold the door in place. Wall Oven, the broiler never work. Present, range oven does not work at all. We have a repairman that is trying to get parts. Present, refrigeration control panel does not work, need repair. These appliances were to be a our luxury kitchen, but turn into a nightmare. Do not buy this appliance, you are wasting your money.

We remodeled our home and purchased Dacor appliances for our kitchen. Range, love it, Microwave, 30 Double oven and warming drawer (promotional give away). The ovens from the beginning do not function well. To warm up the ovens I have to wait 45-50 minutes and it buzzes. It is at temperature but then when I look at thermometer we are close to 75 degrees below. It recycles temperature every 75 degrees too. We had many repairs to the original unit to the point the repair person recommended that Dacor replace the unit. They did, another disaster. First they dropped the old unit while removing it chipping my granite, destroying my drawer panel and then left an absolute mess. The second unit has the same warm up issues, holding temperatures and oh wait, fans ran for hours after they were turned off. Broiling amazing. Baking and convection, a joke.The last repair person told me to open the oven and turn the cookies to have them cook evenly. And do the same when cooking with Convection. :/ I am currently looking for a reliable double oven that I can use and feel good about the food I serve (to be cooked). Dacor basically said that they cannot help me anymore because we went out of warranty last year and sent a repair person to basically say it is acceptable. Obviously for someone who does not cook, just sayin.

We bought our house in 2010 and our Dacor stove was supposedly newer. When I went to clean it, I found loose screws in the bottom. Apparently, the convection element is loosing its screws and washers. Ive had this appliance fixed once already when the cooktop kept clicking. The black plastic around the controls cracked mysteriously. It takes 3 hours longer to cook a turkey than it should. This is a strange stove, which supposedly cost a lot. I wonder if a convection part missing two screws should be used?

We had our range oven for less than a year and the front electric panel cracked, there is no stress to this area. I called the company and they admitted the entire panel was defaulty and had a recall. They did replace it. Within 5 months the new one cracked in the same place. This time they stated the unit was out of warranty. I told them the same type of recalled panel was installed. They said I could buy a new one. Ha! Since then many more cracks. I will never buy anything made with the Decor brand nor do I recommend them! Happy shopping.

I built my home in 2003 and installed a Dacor 30 wall oven. After several years of poor performance, we started to get an error message. Dacor suggested replacing a board for $300. That didnt work so they had me replace another $300 board. That didnt work so they told me I needed a new front panel and it would run about $1,000. That board is on back order and they dont have a replacement date. Thinking that its bad business to sink $1600 into a troubled product that has terrible reviews on the internet. We found out that once you go with Dacor, you need to stay with Dacor due to an unusual, nonstandard size.Thinking that Dacor has improved their product we ordered a brand new $3,000 Dacor RO130 30 wall oven. It arrived promptly and I removed the defective $3,000 oven and put in the brand new $3,000 Dacor RO130 oven. What I got was a dead brick. The Dacor customer service has been awful, and will not allow me to talk to anyone in their technical side. The oven is getting power. Dacor customer service wouldnt help me unless I could prove that the unit was getting power. So I had to get an electrician in to prove that I had properly wired the 4 cords that came off the original defective Dacor wall oven. Get service help? No chance. I live 100 miles from Seattle and no one wants to work on Dacor. So here I sit with a $3,000 brick. No service and Dacor has no clue on how they will service this wonderful $3,000 RO130 30 wall oven that is an out of box failure. I dont see how a company that has this bad of a product, two generations of defective ovens, bad customer service, reluctance from the repair community to work on their products will be in business much longer. If you are considering Dacor appliances, consider the problems that I am having. The nonstandard size of their ovens will lock you into future purchases to replace their products that dont last 10 years.

Dacor Fuel Range broken door - My Dacor is by now 13 years old. I see from other reviews that the problems I have with my range have not been addressed in newer models--the same problems exist. When I received my Dacor, there was a crack in the front, above the door. It was small, and Id just had a baby so I let it go. I noticed that the door did not close either, and because I did not address it within a year, Im out of luck. But youd think that making an oven with a door that closes snug would be a top priority. It only closes properly when in cleaning mode. My oven window became brown and I cannot clean it. Its a shame that these things are messed up because the convection seems to work wonderful and the oven is fairly attractive. If the door closed all the way. Im getting ready to consider a new oven. Wont be a Dacor.

The range cost over $7,000. In the first 2 years multiple malfunctions in the mother board, the convection oven functions, and had to hire a local company to repair. The Dacor company did not care. Called them multiple times, wrote them and received no assistance or response. Repairs cost $$$$ to fix each time something broke.

I bought a Dacor dual-fuel range in 2002 for my new house. Within 18 months, the control panel on the front had shorted, causing the stove to emit a continuous beeping. I got this repaired, and was advised that I should not use liquid cleaners on the stove! Two years later, the same thing happened again. Finally, about 4 years ago, another fault developed in the 3rd control panel, the circuit controlling the oven lights will not respond to touch, and the oven lights switch on and off continuously. Not prepared to pay for yet another control panel replacement, I switched off the power to the stove at the main fuse box. I have continued to use the gas cooktop only, lighting it with an ignition wand. The Dacor stove is only part-functional due to what is obviously a severe design fault in the front touch control panel, which causes the panel to short. I switch on the power to the unit twice a year to use the oven at Thanksgiving and Christmas for large roasts. This stove was a very expensive mistake. Luckily, I have a second (Wolf) oven in my kitchen, which I use instead for everyday cooking.

Dacor Worst Oven Ever. Major kitchen remodel in 2005. Designer recommended Dacor for great styling and the fact that it was a 36 inch oven. Before the kitchen was even finished the control panel had to be replaced. Since 2005 our local repair shop has had to replace the circuit board 9 times. Same issue every time with not heating and board found every time to be burned out! Dacor replaced the first few boards free but we had to cover the labor. To date more than 5,000 in repairs. Dacor would not replace the oven and had terrible customer service. Its down for the 12th time and its headed to the junkyard this time. I cant see spending another dime on this lemon. Dont ever buy a Dacor!

Warning! Do not buy Dacor appliances! We have had our appliances for three years now and all of them have had something wrong with them. Oven circuit panel went and had to be replaced! Dishwasher arm and seal broke and dishwasher leaks! Refrigerator freezer compressor went! Hood range switch broke and had to be replaced! Dacor is the worst appliances I have ever bought! Buyer beware!

As a contractor, we were fortunate enough to build our dream home which was completed in 2005. After much research and many show room visits, we purchased Dacor appliances for our kitchen. As the saying goes, if I knew then what I know now. Our biggest (note I said biggest, not only) issue is with our ESC130 oven. If you own this oven, do not, repeat, do not, use the self-cleaning mechanism. I have had this repaired once and then replaced once (along with a relay board). I seldom use this because I know when I do the lock mechanism will continue to cycle until it is replaced. This means, while I can still use my oven, I have to time when I open the door based on when the lock is cycling in the unlock position. I must also turn the oven off at the circuit breaker or listen to the continuous warning beep that the lock is cycling (as if I didnt know).After repairing this feature once, I next choose to have the mechanism replaced and Dacor offered me a discount on the parts (the oven was and still is out of warranty) at a cost of more than $500.00. This is on top of what I had already paid to have it repaired just 18 months earlier. I feared using this feature again as I didnt want a repeat performance. After cooking macaroni and cheese yesterday, I felt I really needed to clean the oven and made the mistake of using the self-cleaning feature of the oven. I dont know why I was surprised when the locking mechanism refused to stop cycling.I contacted Dacor today only to speak with the rudest customer service representative I have ever encountered, Steven. No last name. He is the only Steven who works there. He refused to listen to me, spoke over me when I did try to talk, and did not allow me to speak with anyone else. There are no supervisors available on Fridays and he could not transfer me anywhere. I left a message for someone else to call me (they did not). I called back later that afternoon and was given the name of a supervisor, Nhi. She was not available and I spoke with another customer service representative. I learned that Dacor is aware they have a problem with this locking mechanism and are trying to correct it. This got my hopes up, thinking that the company would now do the right thing and replace this mechanism at not cost to me, or at least at no cost for the parts. Not so. Even though Dacor knows there is an issue with this mechanism and they are supposedly trying to correct it, all they can offer me is a discount on parts. Really? Wow! A discount for a part that you know doesnt work properly and probably wont work properly because they are still working on the problem? I just really dont know what to say. Is this supposed to make me happy as a customer? Would prospective customers want to buy a Dacor product knowing that Dacor is more than happy to sell me a known defective product at a discounted price and they should expect the same? It is probably needless to say that I would urge all prospective Dacor owners to not waste their money on any Dacor product as they do not care about their customers. I will certainly be doing my part to warn others and hope this serves to warn others as well. Dacor has a lot to learn in terms of building even what could be called a good product and standing behind what they sell as well as becoming a customer service oriented company.

We purchased our home brand new in August 2006. The house was built and the appliances installed (but never used) in 2003. One of the things that sold us on the house was the kitchen being comprised of all high-end Dacor appliances (double convection oven, cooktop, dishwasher, and built-in microwave). Our excitement quickly turned to frustration. The first problems began with the dishwasher, which after several attempts at repair (circuit board) was begrudgingly replaced by Dacor, with “begrudgingly” being the key word. I have always found Dacor customer service to be rude and dismissive - with the only way that I ever received a satisfactory outcome, being via threats of contacting the BBB and Missouri Attorney General.About a year after receiving the replacement dishwasher, the internal racks began rusting badly. Once again, I called customer service who originally wanted to sell me new racks at a discount. Only after another persistent round of explaining that high-end dishwasher racks should be made from a material that doesnt rust, complaining and threatening, did I receive new racks free of charge. I was also informed that they had changed rack manufacturers and that would eliminate the rusting problem. Wrong. It has now been another couple of years, and the new racks are rusted worse than the previous ones. That is just the dishwasher.Our Dacor microwave display began slowly losing its LED display about 2 years ago. Lately, the microwave interior lining is beginning to disintegrate and rust through. One of the burners on our gas cooktop makes a constant popping noise when lit. The top half of our double convection oven no longer heats beyond 250 degrees. I realize that our appliances are now significantly beyond their warranty period, so I am no longer even attempting a resolution through Dacor. I will most likely ride these appliances into their graves and replace them with another brand. I am writing this mainly to alert others about my experiences with what I believe to be Dacors total lack of quality at a premium price. In my opinion, Dacor is all style and no substance.

Dacor came through! They sent me, at no charge,a replacement part. This new part is supposed to fix the issue of ice cycles in the freezer. Its a new drainage system that actually heats the water in the pan so it does not freeze up causing the water to back up. I am hopeful that this will permanently fix the issue! But props to Dacor for stepping up to the plate to fix this! Thanks, guys!

Updated on 09/08/2019: Received a long apology from Dacor regarding their complete inability to service our range stating they would make it right. After sending them all my contact info privately at their request, we have heard nothing. My husband drove to Houston to their showroom, met with Dacor rep out of California, still nothing. Note there are only a few suggested repair services on their website which none cover our area. Avoid Appliance Genius. They wanted $ 500 just to drive 50 minutes travel cost. So here we sit, broiler in main oven out, lighters do not work, and the control screen is blank. Yes, Dacor was great until something broke.Original Review: Our Dacor range was great until it started needing repair. First the broiler went out in the main oven. Then some of the lighters quit working. When we called for repair, every place we called said they would no longer service Dacor because they were unable to get parts. For over a year we have gone back and forth with Dacor state office. They finally sent a “tech” from a video repair store. Really. He charged us $170 to drive to us. Then said he couldn’t get the brass rings off the burners, sorry. Called Dacor again and they said if we found anyone to let them know!!! Yesterday, the the touch panel burned out. I’m done. Dacor does not stand behind their products. I have documented all conversations. Do not buy Dacor.

Im reading all these reviews and my story mirrors them all... I have actually contacted a lawyer and am considering either a lawsuit or going to small claims court because, at this point, its cheaper than continuing with repairs every other year. Has no one else considered a lawsuit under your states lemon law? Appliances are usually covered. I purchased the MORD230 wall oven in 2008... It was purchased as a second oven to my 6-burner Wolfe to cook a turkey or roast during the holidays. It has been used no more than 24 times... I have gone through 2 control panels and am now having glitches with the third. After doing a self clean recently the whole heating element blew - it will not heat at all. I am able to enter the temp but the oven just runs and runs and never heats. I have called Dacor furious for how many times this thing has broken in relation to how many its been used... They have offered parts at a reduced rate but I am not sinking another dollar in this oven on labor and parts only for it to break again. I asked for my money back and told them to come and get the piece of garbage they sold me. Do yourself a favor and buy a Wolfe... It works beautifully... My only problem was the cast iron grates rusted a bit recently... I called their customer service and was on the phone for no more than 5 minutes and they overnighted me a whole new set no questions asked! Dacor customer service has been a nightmare - so much back and forth... I tell everyone I know... DO NOT buy Dacor!!!

We purchased a under counter Dacor oven. The timer started given problems, tried contacting Dacor. The rude customer service advisor first talked to me like a police interrogation, then said sorry cant help. A joke of company with cheaply designed products. Never again.

My Decor Epicurian oven and range has been a nightmare from day one. I have had the oven for about 8 years and had it repaired so many times I have lost count and had spent at least $2000 on repairs. We have experienced motherboard burn out, membrane failure, temperature control malfunctions, error messages that cause incessant beeping. Nearly all of the problems that have been described in this list of complaints, I have had the problems themselves multiple times! Now, I am panicking a bit because I decided to use the self clean function on my oven this morning and now, I have read some sad malfunction stories following the use of this feature. I am so torn about whether I should just cancel the cleaning process. I do not want to risk having the oven malfunction again, but the thing really needs to be cleaned.

I emailed Dacor for information about how to get my range fixed and was amazed. My questions were answered complete with numbers for model and needed replacement parts along with contact information for local service folks. Amazingly good service. Bravo, Tori **! Give that woman a raise!

We have a dual fuel Dacor oven purchased in 2001. We have the manual. For some reason, after cancelling a timer, the oven locked at :4. The owners manual was no help. The Dacor website was no help. We turned off the circuit breaker then turned it on again and finally, the oven worked.

We got a Dacor oven and microwave wall mounted Unit 7 model DMT 2420S when we remodeled our kitchen. I have had problems with the microwave with sparking on and off. I have stopped using it as I am worried about a fire.

My Dacor (3 years old) oven top burners igniters dont stop after being turned on, although they are burning. Ive tried drying them for many hours and applying rubbing alcohol. The front ones do this all the time when we turn them on. When we turn the left front burner on, the front right ones igniter does it along with the left! The back ones do it occasionally, so are still usable. Apparently this is a common problem with Dacor units. Why havent they fixed it? Weve had them fix the electronic panel at huge expense, and are not going to call them again. When the back burners stop working, well get another unit. Ive had gas stoves for 30 years and have never experienced anything like this poor quality. Its amazing that they are still in business.

We were out of state from December 21, 2014 to January 2, 2015. The condition of the refrigerator was discovered at about 9:30 PM on Saturday, January 2nd. Upon opening the door the Dairy Compartment Cover fell to the floor. We could immediately see the damage but did not know the source. As a result, the unit was turned off. The owners manual was consulted along with a review of the Dacor website. The office was closed on the weekend so Monday was the earliest we could obtain names of Dacor authorized repair agents in the Phoenix area. A authorized Dacor repair technician stated the light switch or light circuit in the board failed. The interior light bulbs located at the top of the refrigeration side of the unit remained on when the refrigerator door was closed. The heat generated by the continuously lit bulbs led to the melting and charring of the plastic light fixture. The light socket melted, the wiring harness melted into the socket assembly, light switch, and control panel. The heat was intense enough to warp the Dairy Compartment clear plastic cover, some of the adjustable door bins, and the interior door liners. Also, all food containers made from plastic such as salad dressing bottles, mustard, ketchup and mayonnaise, etc. were disfigured. Of course all the contents from both the refrigerator and freezer had to be disposed.Before leaving on an extended trip we had been following the instructions preparing for a vacation listed on page 19 of the owners manual. On our departure date the food that would not have lasted more than two weeks was removed from the refrigerator. The ice bin was emptied and the wire shut off arm was raised to the OFF (O) position. Note, page 19 does not mention to set the Sabbath mode when leaving for a short or long vacation. We were fortunate that the damage was contained within the refrigerator.

I purchased a 48 Dacor Epicure stove in October 2010. We moved into our home in November just in time for Thanksgiving. We remodeled the kitchen and the stove is the focal point. When I heated the two ovens, the pre-heat mode stayed on but the ovens went to 600 degrees plus. My oven thermometers only read to 600. That happens every time and the fans stay on for hours. After many service calls, we have determined that the oven is going into a cleaning mode every time and is wired backwards. Dacor is ignoring me.

We had a ongoing problem with a wall oven that was purchased in 2006. The most recent complaint was a oven glide rack that was not working. After complaining about it to one of their staff, they listened to our frustration and are sending us a new rack at no charge. My hats off to the great people at Dacor. Thanks for your understanding. Al

Dacor refuses to take responsibility for defects in their products. Our wall oven required two cooling fan motors and two relay boards over a relatively short period of time. In addition, all of the sensors had to be hard wired when the oven stopped working, and our service technician was informed by Dacor that moisture tended to get into the sensors on these ovens. We spent nearly $1500 on these repairs. Reaching a customer care representative at Dacor can take upwards of 20 minutes. Phone calls are not returned. Customers are left to pay the cost of defects in Dacor products.

My wife and I purchased a new Dacor dishwasher, new Dacor range and new Dacor microwave oven. Unfortunately, the dishwasher never worked and were now going through the process of getting the unit repaired. A repair technician was sent out and discovered a new CPU was needed. Then once the CPU was installed, a new circulatory pump was needed. And finally, once the circulatory pump can in, the unit still doesnt work. Weve had the technician in four separate times (installation, tech inspection, CPU install, and circulatory install) and each visit is approximately one week between visits. Yes, were now going on four weeks without a dishwasher that we paid for. Beyond that, someone needs to be home each time they visit. So now Im without a dishwasher for four weeks and I have to take four days off of work so a technician cannot fix my dishwasher. When I called Dacor customer service and asked for a temporary unit until mine is fixed, they simply stated we dont do that. Dacor may be a premium appliance manufacturer but they do not have a premium customer service department. So buyer beware, if your unit has any problems Dacor will not rush, hurry or try to accommodate you. Im sure the unit will eventually get fixed but after a month of waiting, I believe Ive earned the right to warn others about Dacors business practices. We purchased the unit from Pacific Sales in Corona, CA. When we asked Pacific Sales for assistance they said it was a Dacor issue and refused to assist us. These two businesses will no longer receive my patronage.

I recently complained about my Dacor dishwasher that would stop running during the cycle because of a faulty circuit board and touch pad. The repair would have cost me $500.00 to replace the entire touch pad and circuit board and the Customer Service department was not in the least helpful or concerned. After making the complaint on this site, I received an email the next day from James who was very nice and asked for the model, serial number of my dishwasher and who was the repair company I used. I emailed the information back to him and after verifying my information, he informed me that the parts would be shipped to my house at no cost and I would only have to pay for the service call! Now that was great service from a company who is trying to make good for a bad item in their appliance line. My repair person told me that Dacor is now using a different manufacturer for their dishwasher so hopefully it will be a better product.

We have a 2 year old 36 inch, Model EF361WF refrigerator. Water began pooling at the base every 2-3 days. Called Dacor Customer Service Team. Pitiful response and horrible customer service. Had to call private technician who was very surprised that a so-called higher end appliance was not factory-fitted with a P trap. He sees the problem often with cheaper models. Dacor has let us down twice. Buyer beware: sub-standard products matched with sub-standard customer service. Dacor will never get our business again and we would recommend all potential purchasers to consider other brands.

This week Dacor installed my 2nd replacement gas range. I remodeled my kitchen 3 years ago and chose Dacor because I had a great experience with their appliances in the past, had their oven and stove in my kitchen for 15+ years and never had a problem. With the first new range, the oven started to automatically shut off due to excess heat escape, so the safety feature would kick in and shut the system down, in addition the knobs would become very hot even when the over was used briefly, 12-15 minutes. I was very impressed and happy with the customer service through Dacor, they immediately gave me a brand new over. Exactly another year, the new oven had the same problem, door begins to not hinge properly and heat begins escape, knobs get dangerously hot.This week Dacor very kindly, replaced my appliance with the new Dacor Renaissance 36. I used the oven for 12 minutes on 400 and the entire exterior is dangerously hot. I do not have any children, however, if I did I would be terrified that they could seriously injure themselves. The exterior of an oven should not become hot like this. Has anyone else had this issue with Dacor? I feel they have been very responsive with regards to customer service however I want an appliance that is safe.

Purchased a Dacor Epicure ER36DSCH/NG RANGE and oven in 2007. Sad story, it never worked properly since day 1. Initially a gas burner did not light, they came and repaired it. Subsequently the door lock failed in the lock position - had that repaired. The door lock failed the next year again, this time thanksgiving, ruined the dinner. They fixed it but the following year the lower burner element failed at Thanksgiving. All my relatives know not to purchase a Dacor product. Problem is I am stuck with this boat anchor. The oven door motor has failed 3 more times and thankfully the service man showed me how to change it. Today we tried to bake some apple pies and found the oven temperature set at 450 was only 350 (bought an oven thermometer). This explains why it always takes so long to bake things. A complete piece of **, never ever buy one.

Epicure Range, wall oven, microwave and fridge - When remodeling our kitchen in 2010, an appliance salesperson gave us a good deal on the entire set. We spent $20k on the Dacor appliances. BIG MISTAKE! Do not ever buy anything Dacor. We have issues with every single one. Where do I start? The ovens have gone out three times now and I have had to replace the main panel, now it will not heat at all. The refrigerator 42 built-in is a big piece of crap! We have had it serviced 4-times for everything. The entire fridge freezes over due to a design flaw. The fan in the freezer completely ices over. The ice door broke. The crushed ice broke. The plastic door for the butter broke. The shelves broke.The microwave has had issues and has had to be fixed. The oven temps were wrong. Fixed those myself thanks to YouTube. When talking to the service guy he said that these are cheap appliances with the Dacor badge, so you have to spend big bucks to buy them and big bucks to repair! Do yourself a favor and if you are thinking of Dacor run! I contacted Dacor and they are even worse to deal with. They did not care that their appliances are very unreliable. Never received a return call, email, or even a letter.

I owned a 36 Dual Fuel Epicure range that required at least an annual repair for the same thing. The control pad (the pad with the buttons that controls the oven and light) would fry. This would cause the oven light to come on and off like a strobe light. Luckily, I purchased an extended warranty from the vendor, as each time this was replaced it was $750+ to repair. When I complained to Dacor on their support line, the representative actually told me that I was running the oven too hot!About 6 months ago, I sold the house and left the very expensive range behind. It was problematic from day one. Other repairs included replacing the ignitors. After a year of use, the insulation on the door came loose and was hanging in plain view through the window on the door. Every repairman that came to service the range said the same thing.... that they repair a lot of Dacors. When it worked, it was a great range. If you do buy a Dacor, do yourself a favor, buy the extended warranty. You will need it and it will pay for itself.

Dangerous condition! I purchased a Dacor 36 dual fuel range 5 years ago. I reported the issue to Dacor via email with no response from customer service. I believe the no response was an attempt by Dacor to distance themselves from their responsibility for this potentially dangerous condition. Specifics: When pre-heating the oven in convection/bake mode, if the oven door is opened before reaching the set pre-heat temperature, a ball of flame will explode up from the opened door. The ball of flame is basketball sized and has singed eyebrows and hair on several occasions. To reiterate - it is a ball of flame, not super-heated air that is the problem. As a result, after non-response from Dacor, we called a decor qualified repair technician who diagnosed the problem as a bad igniter. The igniter was replaced and the problem still exists. I fear that a small child may be severely burned by the engineering design fault.

Purchased a Dacor DT0227B wall oven. The first oven arrived damaged; the control panel was completely off the unit. We ordered a replacement oven which arrived today. Upon turning on the power, error codes C76 and C77 appeared on the control panel display. The installers phoned your service people who instructed them to remove the front panel and look for a loose wire. When they removed the front panel, the entire control board was just hanging free, not secured in place with any screws (it appeared that this was an assembly error). They found a wire hanging, secured it in place, reattached the control panel and applied power. At this time the error codes were no longer displayed and they were able to set the time. When they attempted to start up an oven cycle to test the unit, the Start/Continue button on the membrane keypad was not responding. Another call to your service team determined that the control panel would need to be replaced. 2 ovens within 2 weeks arrived DEAD! The quality is beyond unacceptable. I sent an e-mail to the CEO of the company before I posted this. I received a response from a QA guy. Any manufacturing company that thinks Quality is the responsibility of QA is working with a 1950s mindset!! Dacor is pitiful and will certainly not last as a company with this kind of quality and customer service!!

I purchased a Dacor range hood 3 years ago. I had an intermittent problem from the start, as one of the two lights would intermittently go off. Replacing the bulbs didnt fix it. As one light worked perfectly, it became a tolerable issue. Finally, I was having other electrical work done in our home & I asked my electrician to look at it two weeks ago. He figured out that it was a defective lamp housing that incorrectly held the lamp bulb. Dacor shipped me a replacement lamp housing for me at no charge. I installed it this last weekend and it is running fine. Thanks, Dacor!

Dacor Distinctive Series Range model DR30D - One week after the appliance warranty expired, the oven stopped heating. The repair man replaced the circuit board. We still got a code 33 when we try to get the oven to heat to 400 degrees. Called customer service, they said to flip the breaker to the unit off for a few minutes. Seemed to help but we do not use the oven much, as we also have a Meile microwave/oven that we love and use that more. Then I cleaned the oven using only the ovens program. That locked down all of the gas cook top knobs. I called the repair service, it snowed on the Saturday of the appointment. They cancelled. I did not check the stove on Sunday. On Monday the repair service walks in and simply turns it on, no problem. VERY FISHY!!! I have heard the manufacture can control it by computer chips. This appears to be very true. Now the stove does not heat past 250 degrees. After speaking to a few people it appears this is a very common issues. Dacor is a lemon. Do not waste your time and money.

I have owned a Dacor Convection microwave for a few years and is so far the best Ive ever owned. It works great every time, has great preset features and also has a great stainless steel look. Great Product.

I purchased Dacor Brand cooktop, oven, microwave and dishwasher. The dishwasher quit working after four weeks. Price tag for the dishwasher 2,800. Three weeks later Pacific Sales in Corona will not take the dishwasher back and replace with a new one. Dacor is struggling to provide a service tech in my area to look at the machine and honor the warranty. In the mean time I am shelling out money for Dawn dishwashing liquid and washing the dishes by hand. Complete JOKE. If you want a brand that will not stand behind their product... purchase Dacor. Want a salesperson who will talk up a brand but the Store washes their hands of the transaction after payment, shop Pacific Sales in Corona Ca.

We have an 11 year old Dacor double oven with convection on top. The relay board malfunctioned and there are no parts to repair this. All Dacor would tell us is that they dont carry the parts anymore. Evidently, they are not required by law beyond about 8 years and that appears to be all they do. Our appliance repair person even contacted a company that rebuilds electronics and they cant get parts for this board. It is unbelievable considering what we paid for the oven. So we now have to replace it. Dacor offered us a discount on a new one. Not good enough. I cant imagine putting another Dacor product in. Two appliance service people have told me that Dacor has this reputation and they would not put them in their own houses.