48 in. Range - Wish I had read reviews first would NEVER have purchased Dacor. Paid almost 11,000.00 for a range so many issues they replaced it. New range came with 7 defects. It has been over a month and nothing has been done about it. Everyone keeps passing the buck and I am sitting with an high end expensive product and no help from Dacor. I am being very patient but also very frustrated at this point.

We built a new home in 2004. All appliances were Dacor. Since then, the oven has had to be repaired 4 times; the microwave had to be replaced; the cooktop has had two repairs and now will not light automatically; and the patio barbeque completely burned up and some of the parts melted. I did report that to the company and to the US Product Safety Commission. We have not abused any of these appliances and have followed the manufacturer recommendations all of the time. Dacor charges top dollar for their appliances, but they are not as good as cheaper brands. If you try to contact Dacor, they have a well-so-what attitude.

Purchased Dacor Renaissance wall oven in July 2015, Model RNO130S. After less than a year and a half, the cooking temperature began to fail. For instance, set to bake at 425 degrees, the oven would appear to heat properly, but tried and true recipes would be pasty and uncooked at the expected time. I inserted an oven thermometer inside to test and found an erratic pattern of oven heating up properly to 425 but then sometimes dropping back to about 350 during cook time and refusing to ever reach 425 again. ABT repairman adjusted temperature calibration but refused to troubleshoot any further. Just ruined another dinner. Thanks Dacor and ABT for your unreliable product and poor service.

I rarely write reviews but when I found your site, I decided it was time to vent. I bought a 36 dual fuel, convection Epicure range in 1999. It was not a cheap oven and I was excited at the possibilities of having a 16,000 BTU broiler and large oven cavity to work with. Lets just say that excitement quickly wore off. Almost immediately after the range went out of warranty, the ignitors went bad and we also had to replace the control panel ($400 in repairs was a lot back then). After that, we continued to have ignitor problems and replaced them again. Finally, I just stopped doing it and lit them with my aim and flame. I never allow my children to cook on the stove because I am afraid they will be burned. Most recently, my broiler element, relay board and again more ignitor problems ($1,200 in repairs). Not to mention, the repairman had a terrible time trying to access all the areas and was at my house for 4 hours trying to do so. When the initial problems happened, I emailed, phoned, left message, etc. to no avail with customer service (I use that term loosely). This company is the worst. I have told everyone I know never to buy a Dacor anything. Next time, Ill buy a Wolf.

The ovens needs a new latch kit and a mew control panel every year. It has been repaired 15 times. So many issues but those are the most consistent problem areas. Dacor should have replaced our range the first year. Even the repairman says everyone has had the same issues. For what I have paid in repairs I could have bought a new range.

I submitted a review regarding a repair on this same refrigerator Dacor EF42BDCBSS back on 10/29/12 and 10/31/12. We now have another repair bill in the amount of $486.42 for a drain pan kit and defrost thermostat. I tried to contact Dacor by phone and email to talk about the situation, but have not received a response. I would highly recommend that you think twice about buying a Dacor brand refrigerator.

As an add-on to my original review, I had a a service call to address the LC error code. The service company reconnected my unit, turned it on, ran a couple tests, and declared there was no issue. We ran the dishwasher 1 cycle and it worked just fine. Tried to run it again later that day, and the LC code was back again. To resolve the issue, I worked with the company I bought my appliances through to replace the Dacor dishwasher with a Bosch. That happened today, so it is too early to tell say how the Bosch works, but it is more solidly built, has more capacity and the door fully opens with the panel installed.Dacor did reach out to me to try to resolve this issue, so kudos to their customer support, but the issues were just too many. And as I stated in my original review, love the Dacor range top, double oven and refrigerator.

The oven I purchased is the Dacor double oven, model number - ECD230SCH, I purchased extended warranty on the ovens. This was purchased when I bought the ovens. I have renewed this and still have a warranty for 2 more years. I cannot get anyone to do the repair on this oven. My location is at the Sardis Lake. I cannot get anyone out to service. I do not know if you have any thing to do with this. I have had an oven out since June 2013. Please help, Dacor should have service reps in this area. I am in Sardis Ms.

Have had an on-going issue trying to replace an oven door....since early December 2020. Have gotten a continuous run around regarding status of new door and shipment of same. Friendly Customer Service Reps do nothing to solve this issue. The oven door is designed not to be repairable or user friendly. Poor support and steady excuses have created another DIS-SATISFIED CUSTOMER!! AVOID DACOR!!

I have had my 30 inch Dacor Dual Fuel Range since 2002. In the past month, the oven door seems to be falling apart. I had to replace the oven door handle after the handle cracked in the spots on the right hand side where the screws go in. When I tried to screw the new handle in, I noticed that the front panel on the door is lifting away from the door. It is more separated on the right hand side which leads me to believe that it is the reason that the handle cracked on that side. As a result, the handle cannot be properly installed. The only way this can be repaired is to call someone in to do it and it will either have to be glued together or the whole door would need replacing. Reading these forums, Im worried that my oven problems are just beginning and I dont want to start sinking money into this oven. I purchased a Dacor as I believed it was a high quality product and that it would be worth the money and last a long time. This type of problem should not be occurring. I do not consider 10 years a long time for a product like this. My sister has had her Jenn Air oven for almost 20 years and it has no signs of wearing out.

I did a kitchen remodel in 2008 and was convinced by the sales guy at Home Expo to go w/ the Dacor over the Wolf. I bought the dual-fuel 36... Within 2 years I had serious problems. The oven, when not on Convection Roast or Con Bake, just using Bake will consistently turn itself off... Ive ruined many a meals, usually big ones: Turkey, Prime Rib(long cook time items). This was by far my most expensive investment in my kitchen and by far my biggest disappointment. I have called Dacor in the past and was told they could refer me local repair people, I was on my own for fixing it. Again, huge disappointment.

DONT recommend model #MOH130. We were so impressed with the options that this oven came with. Sadly, with all the bells and whistles also came a ton of repairs. After the 4th repair, our service rep said the relay board needed to be switched out. (Half of the service men who came to my house seemed to be grasping at straws trying to come up with an explanation why the temperature was fluctuating, or why it took so long to heat up, etc.) Then I get to wait 2 weeks for a part to be ordered/arrived and re-schedule service. Last week got code U22 - oven wont even turn on. This oven is only 6 years old. NO THANKS - NEVER AGAIN will I buy anything from this company.

Follow-up to March 31 posting: In 2001, we installed two Dacor wall ovens and a gas (converted to propane) cook top. The cook top has been problem free and the brushed stainless steel surface still looks like new. Both ovens however, at that time, were problematic during the two year-warranty period. Knowledgeable service people were hard to come by in our region. After numerous service calls, Dacor replaced one of my wall ovens at or around the three-year mark (outside of the warranty period). That particular unit had only one minor issue since then and Dacor replaced the appropriate part free of charge. The other original unit has been problematic since the beginning. The latest problem being the internal light going on/off for no reason and then a lack of response to light button on the front control panel.Long story short, I posted my frustration here on March 31 and was contacted by a Dacor rep within two days. He asked me for detailed info on the problem and located the unit in their files. Some of the past repairs were known to Dacor, but others were not since we just did them ourselves. I was asked to send a detailed description of the current issue along with pictures, which I did. Based on Dacors analysis or the pictures and the exhibited problem, they sent me, free of charge, a control panel membrane, a door gasket and a set of door hinges. We installed these items and the unit is now in full working order.In looking back over the past years of problems with this particular unit, its clear to me the issues all stemmed from an original broken door hinge. It was compounded by the fact that the service and repair folks at the time considered the door gap to be within tolerance and we did not discover the broken hinge until the door glass shattered and we needed to replace it, which required removing the door. Anyway, at this stage in the game, I am very pleased with Dacors response. It is my impression that they are trying much, much harder to stand behind their products. So, while just a short time ago I would have never considered another Dacor product, when the time comes, they would still be on my list of considered vendors because when these ovens work, they work great.

Bought expensive refrigerator in Miami. And because I live in Miami 2 months in year use and tern in refrigerator only for 2 months. Every year have problems for thousands dollars. Company keep changing parts. I keep paying. Same problem every year. Big mistake to buy Dacor appliances. Regret very much and angry. People who fixing they know nothing. Only money. Very not happy. Looks like new. Today will throw on the garbage.

Arrived in good condition and so far works perfectly. Delivery was delayed by one day because of the incompetence of my local mail service. I bought this microwave, as others have described, to replace a 13 year old Dacor that had not really died but had lost the electronic screen. We put magic marker numbers on the display screen where the numbers had been 5 years ago and kept using all the functions. I decided to replace as, without the display screen, I could not do anything semi sophisticated with this microwave but its motor and microwave capacity was still going strong. This model fits perfectly into the previous 24/27 trim kit. Unfortunately our other trim kit is white to match our old microwave. Decor only has stainless steel now. And the new trim kit for this microwave is flat without the vent slats (plus costs over $300!). From the placement in our cabinet, I think the vented slats are really important to dissipate heat and am puzzled by the change in design by Dacor. The slats are a little tedious to clean but as a TV is above the microwave and an oven below I want the heat to have a better place to go. Ebay has the old trim kit in stainless steel but so far the expense seems excessive for just the outside piece. The internal support bracket for the new microwave is exactly the same as for the previous model so the only part of the trim kit needed for my microwave is the outside frame. This newer model works very similarly to the older version. I am delighted Dacor still makes this microwave to fit my space 13 to 15 years later.

We purchased Dacor appliances twice, (double ovens, warming drawer and gas cooktop), after our first flood, and then again, after we flooded from Hurricane Harvey. (Dacors customer service was excellent in helping us replace all our appliances when we were going through such a horrific disaster because the vendor we purchased our appliance from the first time, wasnt in business anymore.) We were very satisfied with our appliances the first time we remodeled, that we purchased them again, and have not had any problems. The ovens heat up quicker than other high-end ovens and the range top cooks evenly and looks beautiful. I would purchase again, but hopefully, I wont have to.

Dacor dual fuel 30 inch range - First of all the look of the dacor is second to none in my opinion. The digital screen with blue lighting makes this a truly elegant part of any kitchen..... when it works. The range top itself worked flawlessly for me and the main burner was always more than enough. The problem with the range lies in the electronics. The unit has been in my home for over a year and has worked for less than a month total. An error code appeared when ever the oven gets hot. C33, C1, 0000, 1111, C11. Ive seen it all. I have had the main board replaced twice and my local repairman is on first name basis with even my dogs at this point. The final straw for me was when the oven door glass shattered while cooking and when dacor was contacted they said that happens. Im think Ill try Viking.....

Purchased a Dacor Epicure ER36DSCH/NG RANGE and oven in 2007. Sad story, it never worked properly since day 1. Initially a gas burner did not light, they came and repaired it. Subsequently the door lock failed in the lock position - had that repaired. The door lock failed the next year again, this time thanksgiving, ruined the dinner. They fixed it but the following year the lower burner element failed at Thanksgiving. All my relatives know not to purchase a Dacor product. Problem is I am stuck with this boat anchor. The oven door motor has failed 3 more times and thankfully the service man showed me how to change it. Today we tried to bake some apple pies and found the oven temperature set at 450 was only 350 (bought an oven thermometer). This explains why it always takes so long to bake things. A complete piece of **, never ever buy one.

I bought my Dacor epicure 36 duel fuel range in 1998. First stove: oven door did not close, spark modulator out. They tried to fix it but failed. They sent me a new stove. #2 stove: same problem with spark modulator. Couldnt use any burner without the constant clicking. Oven didnt bake evenly. Complained. Stove: #3: same problems. Dacor sent me a letter to grade them on their stoves and service. I blasted them. They called me and ask if I wanted my money back or another stove. Stupidly I took the stove. This was 5 years since the original purchase. Ive had this stove #4 for 13 years. Door is and always has been unable to close. I use a stick to close it. Now the relay board is out. Frankly I so love the looks of the stove and I cant afford to get a new one. Original was 5200. Now they are 6700 and I would probably have the same problems. So I am going to try and fix this stove myself. I will never buy Dacor anything ever again, even if I could afford it. When they offer your money back, take it. The service was responsive although didnt solve the problem through 4 stoves. I would gather from that, the design is bad. My mother has a old 1940 gas stove that still works. Gas stoves should not be that complicated.

We remodeled our kitchen in the fall of 2009 and decided to purchase what we thought were higher end Dacor appliances (stove top, oven and microwave). Well, what a mistake that turned out to be. Considering the price we paid for the appliances, you would not expect problems from all 3. Perhaps a problem with 1 appliance, but problems with all 3 suggest a real quality problem. My first indication should have been when I called and asked how to change the green LED on the microwave to blue to match the nice blue LEDs on the oven mounted right below. I was told that someone else makes the microwave and Dacor just puts their name, and that I should just turn off the LED on the microwave. I dont know if that is true, but that is what I was told.Now when using the microwave/convection feature, the oven makes a noise (sounds like a fan motor) for the first 3-5 minutes then eventually quiets down. A daily reminder of the mistake we made purchasing Dacor. Then those nice blue LEDs on the oven started failing making it impossible to read the clock, timer or temp. Luckily, the oven still works; you just cannot read the LED any longer. This is a constant reminder of the mistake we made buying Dacor as we see the LED every time we walk into the kitchen.Finally, we have the solid surface electric cooktop. Although it works fine, the black paint on the metal trim around the stove top is wearing off. Now, we have some shiny metal and some black trim. This is just an annoyance and honestly, we probably would not have even complained about it. However, with the other problems we have had with Dacor, it just adds to our overall disappointment with Dacor. If I knew then what I know now, I would be a lot happier because I would have GE appliances and not these overpriced low quality Dacor appliances.

Im on my second Dacor 36 range! I absolutely love this product. The large grates on the cooktop allow me to have multiple things going at the same time and the size of the oven is amazing. The oven takes a full commercial sheet which allows me to cook 3 or 4 dozen cookies at a time! Dacors convection system is undeniably the best in class. I can roast garlic and bake a cake at the same time with zero flavor transfer! My turkey at Thanksgiving is so amazing Martha Stewart would adopt me if she could see it! It truly makes the kitchen the heart of the home, not only is it aesthetically pleasing but it is the center of all things yummy at our house!

Warning! Do not buy Dacor appliances! We have had our appliances for three years now and all of them have had something wrong with them. Oven circuit panel went and had to be replaced! Dishwasher arm and seal broke and dishwasher leaks! Refrigerator freezer compressor went! Hood range switch broke and had to be replaced! Dacor is the worst appliances I have ever bought! Buyer beware!

My Dacor oven (DO130S, S/N V-A-10160044) is less than 18 months old. While it was in use, it popped, sparked, tripped the circuit breaker, and died. I called customer service, and voiced my concern on safety due to potential electrical defect. Steven, the customer service person advised me that this oven is no longer in warranty, and to call a repair service. I reiterated the concern for product safety. He placed me on hold, and the call was dropped. I called again, and Mike answered. I repeated the same info, and he was not willing to listen to any concerns. He hung up on me. This experience does reflect on published Dacors commitment to customer service, or product safety.

Dacor Fuel Range broken door - My Dacor is by now 13 years old. I see from other reviews that the problems I have with my range have not been addressed in newer models--the same problems exist. When I received my Dacor, there was a crack in the front, above the door. It was small, and Id just had a baby so I let it go. I noticed that the door did not close either, and because I did not address it within a year, Im out of luck. But youd think that making an oven with a door that closes snug would be a top priority. It only closes properly when in cleaning mode. My oven window became brown and I cannot clean it. Its a shame that these things are messed up because the convection seems to work wonderful and the oven is fairly attractive. If the door closed all the way. Im getting ready to consider a new oven. Wont be a Dacor.

My Decor Epicurian oven and range has been a nightmare from day one. I have had the oven for about 8 years and had it repaired so many times I have lost count and had spent at least $2000 on repairs. We have experienced motherboard burn out, membrane failure, temperature control malfunctions, error messages that cause incessant beeping. Nearly all of the problems that have been described in this list of complaints, I have had the problems themselves multiple times! Now, I am panicking a bit because I decided to use the self clean function on my oven this morning and now, I have read some sad malfunction stories following the use of this feature. I am so torn about whether I should just cancel the cleaning process. I do not want to risk having the oven malfunction again, but the thing really needs to be cleaned.

I purchased a DACOR Discovery IQ Range one year ago Model # DYRP36DS/NG from an online authorized DACOR retailer. Here is a synopsis of the events Ive had with the range over the past 12 months: I took delivery of the Range in January of 2016 at my home under construction. I moved into the home in April 2016 which is when the Range was fist installed. In May I began to have problems with the unit, it would shut down during preheating, then reboot itself, sometimes it would just reboot itself randomly. I called DACOR customer support who told me that I needed to download the latest software version, which I did. Shortly thereafter, the Range again would shut down during cooking and go into a reboot cycle.I called DACOR again, they sent out a local service company. In June the technician came out and upgraded and re-installed the software. The problem continued, I contacted DACOR AGAIN, got the run around, etc... Escalated the problem. DACOR then determined the problem was in the internal circuit board which they arranged to shipped to local service company. The service company came out again, replaced the internal circuit board and attempted to upgrade the eProm, which didnt work. The Range was in a constant state of rebooting itself over and over and over again. The Technician left. Said nothing more he could do. I had to shut the power off so the unit would stop rebooting itself.I called DACOR AGAIN, I got a complete run around, they refused to do anything more. I finally was able to reach the V.P. of Customer Service. After a few conversations and investigation into the issues. She determined that the unit needed a new front controller panel. The panel was shipped to the local service company. The service company came out again and replaced the front controller panel. Its now November. Over Christmas, the unit began to shut off the oven randomly during cooking cycles, for no apparent reason. Over New Years, the oven was shutting off, flashing an error code and reboot! I called DACOR last week. They refuse to help because now it is out of warranty.Ive contacted the online retailer. Ive left messages at DACOR for the Service Manager and the V.P. of Service. NO RESPONSE. So this is how DACOR deals with servicing their high end appliances, keep trying to pretend to fix the lemon appliance until the anniversary date, and then they dont have to deal with their $9,000 piece of garbage high end range any longer. The consumer gets screwed and DACOR doesnt care in the least! DO NOT BUY an appliance from DACOR.

We replaced a Dacor with this new upgraded Dacor. I accidentally started a fire in the last one...my fault not the units. Ours fits very snuggly into the wall which was the primary reason we went for the Dacor brand. Other than having to take off the little rubber pads/feet, it slid right in and we were back in business.

Got a great online deal on Dacor LP gas range. Was new but had dinged side panel according to store. Couldnt see the ding in photos and it would be hidden against cabinets anyway. Range is finally delivered and is new as advertised. Works great for a few days but then the oven wont hold temperature and then wont light. This is when the nightmare begins. Samsung now owns Dacor and getting to the right people to make a warranty claim is insanely difficult. After making the repair claim we get notified that there is no warranty coverage for service as this was not a new unit. Pardon me but we have the sales receipt showing that it is with full factory warranty. They finally agree to accommodate us and then repeatedly cancel repair tickets. After many calls to fix this, they now tell us that no service center will come to repair the range! They offered a refund minus some sort of discount based on a stove being used for a period of time. Oven stopped working a week into having it and they want to DISCOUNT a refund! Made BBB complaint and their response was they would have someone reach out to the customer. Today they did that and we are still at no resolution. Told them they have 3 options, fix the range, replace the range or refund us completely and I will make arrangements to fix the oven. They say there are no ranges in inventory to replace this one with with. No one inside the US will call or reach out to fix this fiasco and we are left with someone that is not allowed to make decisions that speaks english as a second language. Sad thing is that its a basic range that at first seemed to be a great design and would be great to have in our kitchen. Its now endless headaches because Dacor refuses to step up and remedy a defective oven part with a service call from someone that would require likely higher pay than their network providers.

Don’t purchase Dacor appliance - it’s been worst purchase experience ever and I am extremely disappointed. After six months since I purchased the Dacor built-in refrigerator, Dacor couldn’t even ship the proper installation parts and my refrigerator is still not working. Problems:1. Their high end $11K Dacor built-in refrigerator cannot even be installed. Wasted five months communicating with both Dacor and the retailer AppliancesConnection. After five months they were still able to ship the proper missing installation parts. Over the past five months, I talked to six different team members in Dacor customer support team, escalated to customer support lead and also talked to their regional technical manager, none of them is able to solve my problem and ship the right installation parts.a) Their process is extremely messy. Their customer support team had no idea about installation requirement of the refrigerator. And the request from their customer support team is declined by their internal Parts department again and again, only to find out installation parts should’ve shipped by the retailer. This is extremely confusing now and no one in the team seems to understand the right process.b) After Dacor acquired by Samsung, their manufacturing process is very messy and parts are extremely confusing. There’s one version of required installation parts in Dacor manual and one version of Samsung parts in the Parts guide, and no one in the team seems to understand the difference and how to map from one to another (they insist on sending me Samsung parts instead, claiming they’re compatible). I am now the expert myself to understand all their parts and able to identify many problems in their manual.2. As a high end brand, Dacor doesn’t seem to care about their customer at all. As a customer who did kitchen remodeling and had no refrigerator to use for five months, no one in the team seems to care about their brand or their customers. With this huge gap in the process, no one thinks about the problem from their customer’s perspective or shared empathy with me. Dacor as a brand is really bad and I am extremely disappointed in both their product and services.

Purchased a Dacor freezer. Freezer does not come with outer panel. Understandably, because you can choose to put your own custom panel on or order one from Dacor. Found out Dacor was bought by Samsung, a few years ago. So I decided to order a Stainless steel door from Dacor. One of Dacors reps suggested I order from J@J international. I placed order and two days later they called back saying they cannot ship door to me UPS nor FedEx will ship it. They refunded my money, so I reordered from someone else. Got ss panel toe kick and handle. Opened box only to find out no hardware, brackets ss trim for sides screws and so forth. I assumed mounting hardware would be with door. So began the part search for parts. Come to find out Samsung changed Dacors part #s. Vendors who sell the parts could not come up with parts or told me not available. Reliable parts agent told me this. I was told they should have come with freezer. Meanwhile called back Dacor to someone who specializes in dealing with these issues. She took over 45 minutes of my time giving me the impression she was gonna resolve the issue. She finally said we have the parts and inferred that I must have not talked to reliable parts. I assured her I did. She continued to refute what I told her. I have been right at two months trying to get freezer door installed. I called an Appliance dealer in Salisbury Md. to get assistance. He told me when Samsung bought Dacor he dropped line. I now see why. It has been the worst experience I have had with a company that has absolutely done nothing but appear to be concerned and say they are sorry but do nothing. It looks like it will be another 750.00 to get a couple little trims and brackets and a few screws. If I had it to do over I would never have gone down this road. This has been a two month old nightmare that is still going on. Best advice I can give is steer clear of Dacor/Samsung. Was going to buy matching column refrigerator. Not now.

We have a Dacor gas range RSD30R that we bought to upgrade our kitchen in 2002. We have had several issues with the range to date. The first issue we had with the range was the auto lock for the oven cleaning cycle that failed in 2007. It was not covered under warranty and cost $88. The second item to fail were the oven door springs. They also failed in 2007 and covered under warranty. They failed again in 2017 and had to be replaced for a second time. The springs are too weak to hold the weight of the heavy door. $68-$78 for the springs. The springs could easily be changed out as the brackets are still good but they only come as complete units. The last item to fail were the ignitors. Only one ignitor failed out of the four but as the spark module ignites all burners every time any one is turned on, premature failure could be expected as all ignitors light every time. This time the part is no longer available from Dacor. Dacor does not support any products they build after 7-8 years. Parts will no longer be available. I would not recommend Dacor Appliances to anyone as the manufacturer does not support their own products very long. I purchased Dacor to buy American and I regret it now. In contrast every product that Miele made even 20+ years ago, parts are still available directly from Miele and other suppliers as well.

In 2001, I bought a Dacor dual range stove. I paid over $2000. My problem is that there is a defect in the product; when you use the self-cleaning, the outside of the stove cracks up. Dacor has replaced this three times and each time it cracks again. I spoke with them about a year ago and because I didnt continue the warranty, they wouldnt replace it. I carry a home warranty.My stove looks like it came from the junkyard. I understand them not repairing a physical problem with the stove but the outside is crumbling because of a defect in their product. If you dont clean the oven, then you get an error and the only way to get it off is to clean but all that dose causes the outside to crack up more. It pains me to think of buying a new range when I thought I had done my homework, when I choose Dacor. I hope this isnt too late, but it pains me to think after another cleaning I may be forced to buy another stove.

I have a induction Dacor stovetop. Its stopped working and blinks an error code. Called customer service who didnt know what the code meant. I was told my model was 2015 which the rep said was old. It was installed in 2017. All they would offer was cheaper replacement parts if I paid for someone to come and figure out what the problem was and install the parts. I was told the replacement parts were not cheap though. I was told that because were the second owner of the house they couldnt fix it under warranty (even though it should be covered under warranty) because they couldnt say how it was used before (commercially or residentially). Give me a break!It gives me almost no confidence in getting this thing fixed. Warranty is a joke and customer service is terrible. So far I had to leave a voicemail for the reps next level who will call me back after the weekend. Im waiting to see what (if anything) they will do but from the first rep. I dont have a lot of confidence in their products.

We have had problems with the igniter switch which clicks when I have a large pan or pot on the stove. My husband has tried cleaning the igniter tip with a brush as well as the removable ring but we still have that problem. We also have a Dacor microwave that seems to blow a door fuse pretty often that has to be replaced.

I have had nothing but trouble with a wall oven I bought in 2010. Basically just bad electronics. I finally replaced the oven in 2014 and had to get another Dacor to fit the opening. The new unit still does not heat evenly and is consistently off by about 50 degrees. Customer service is not helpful at all. Local repair shops cant really fix issues. Terrible company. Cant figure out how they stay in business.

I spent a lot of money buying a Dacor double wall oven because it was supposed to be top of the line and dependable. Now, the circuit board needs to be replaced and the oven is just 5 years old! This seems absolutely ridiculous for an oven this young to have such a major problem! I am very upset about all the money I am going to have to spend to fix it. Ive never, ever had any oven problems with other brands like this in my life. We remodeled our kitchen and I thought I was getting something better and now I realize that this brand is not living up to my expectations at all! I am using an authorized Dacor repair company and they told me that they are seeing lots of problems with this brand. I do not recommend this oven to anyone.

Our Dacor oven is 2 years old and the oven door stopped closing all the way, rending it inoperable. The company is now owned by Samsung. I tried to schedule a service call to repair/replace the door hinges. This should be a simple process. However, because I purchased the oven through a designer and Dacor dealer, I had to track down the order verification to demonstrate that I am the original owner of the oven (this is in addition to providing a copy of the receipt or proof of purchase). It took several days to resolve this issue with my designer and rep who sold me the oven. Then, I scheduled the service call on the phone only to receive an email hours later advising me that the service call had been cancelled. No explanation was provided. After rescheduling the service call several times only to have each call cancelled, something finally worked with Samsungs tracking system and the service call actually took place.Dacor is the Mercedes of ovens and I expect a service call to be a little more expensive. However, other providers of luxury products facilitate the product support to minimize customer aggravation. Samsung needs to work on its product support and customer service. I would not purchase a Dacor product again since there are several other manufacturers that provide comparable luxury kitchen appliances with much strong customer support.

I bought DCM24S DACOR 1.5 CU CONVECTION MICROWAVE-SS and after few months of using this product its banded on the back wall of the microwave that supposedly resulted from improper turntable placement which caused the turntable tray to make contact with the back of the oven. The quality of the product is very poorly, dont buy Dacor product!

Im reading all these reviews and my story mirrors them all... I have actually contacted a lawyer and am considering either a lawsuit or going to small claims court because, at this point, its cheaper than continuing with repairs every other year. Has no one else considered a lawsuit under your states lemon law? Appliances are usually covered. I purchased the MORD230 wall oven in 2008... It was purchased as a second oven to my 6-burner Wolfe to cook a turkey or roast during the holidays. It has been used no more than 24 times... I have gone through 2 control panels and am now having glitches with the third. After doing a self clean recently the whole heating element blew - it will not heat at all. I am able to enter the temp but the oven just runs and runs and never heats. I have called Dacor furious for how many times this thing has broken in relation to how many its been used... They have offered parts at a reduced rate but I am not sinking another dollar in this oven on labor and parts only for it to break again. I asked for my money back and told them to come and get the piece of garbage they sold me. Do yourself a favor and buy a Wolfe... It works beautifully... My only problem was the cast iron grates rusted a bit recently... I called their customer service and was on the phone for no more than 5 minutes and they overnighted me a whole new set no questions asked! Dacor customer service has been a nightmare - so much back and forth... I tell everyone I know... DO NOT buy Dacor!!!

We purchased this oven/cooktop was installed in February 2020. I have been unhappy with the performance of the smaller oven from the beginning. It takes 20 minutes to pre-heat, a loud fan starts to run partway during the pre-heating process and then warm air starts to flow out the bottom. Plus, it is not either holding the correct temperature or not reaching it completely, nothing I cook in there is done in a appropriate amount of time. Baking a small potato takes an hour and a half at 375, brownies take almost twice the approximate baking time. My attempts to contact them have been less than satisfactory. I wrote for a second time over two weeks ago providing a copy of the invoice and have still heard nothing. I am quite disappointed with this product & company.

Our Dacor wall oven (model MOH 1305) is the subject of my concern. Purchased with confidence in Dacor’s advertising in 2008. The oven has had multiple visits by a Dacor authorized repair company who along with a Dacor technician determined that the oven needed a relay board replacement. This relay board has been replaced twice and has failed after installation both times. The relay board provided by Dacor appears to be the problem. Each repair/service call costs approximately $300.00 with no guarantee that the next relay board will work. Our conversations with Dacor give us no satisfaction. Dacor now tells us that our “superior product” of 11 years is just too old. Additionally, they tell us that Dacor products are “superior products” that are designed to last somewhere between 10 to 15 years. There is no excuse for Dacor since the replacement relay boards they are sending us seem to be defective. Their excuse that we have an “old” oven is wrong since the problem is with their defective replacement parts. Beware consumers when thinking about purchasing Dacor products.

I am very, very pleased to report that I was contacted by Dacor a day after I posted my review which addressed a second failed relay board in 7 years. A really helpful Customer Service Representative called me (not emailed) to discuss the issue in great detail. Within a matter of days, a local repair service had received the new part from Dacor and scheduled an appointment with me to come out and replace the defective part. Dacor covered both the part and the labor. Im really sorry that the oven needed a second major repair but I will say that Im impressed with Dacors resolution of this issue!

Two years ago, we redid our total kitchen at considerable expense. All of the appliances we replaced were made by Dacor. They included: 1) a 36-inch refrigerator model EF 36/wf; 2) a dual wall oven, model EO230SCH; 3) a gas cook top, Model RGC304; 4) a dishwasher, ModelEDWH24S and; 5) a range hood, ModelEH3012SCH. The problems started within a two months of installation. The refrigerator stopped running due to a relay failure and a compressor problem; both were replaced by Dacor at no cost to us. It was inconvenient but not costly. A short time later, the lower wall oven stopped working as well as the lights in both ovens. This required the replacement of the main control panel (control circuit board). Dacor paid to have it repaired. The clock does not keep accurate time and gains about an hour a day. We decided to leave it well enough alone and did not have it fixed. After the one-year warranty expired, the lower oven quit again. This time, it had to be removed from the wall and an exhaust fan in the lower oven was defective and had to be replaced. Dacor’s initial response was it was out of warranty, so it was up to me to cover repairs. They eventually agreed to supply the part (about $90) but we had to spend several hundred dollars to install. Now, the lower oven takes an extremely long time to heat up, and again we decided to leave it well enough alone. Recently, there was a loud flash in the vent hood; one of the bulbs apparently burned out. My wife tried to turn off the lights in the hood but the light switch apparently blew when the light went and could not turn them off. After a couple of burned fingers and a melted bulb removal tool, I managed to get the other bulb out. A call to Dacor got the usual out of warranty response. I called the local Dacor authorized service rep. He looked at the problem ($95) and said he would have to call Dacor. After he talked to Dacor, they called me and said they would send a replacement control board but would not pay for the service calls. The service company said the next service call would be $195. One light bulb burned out: cost $290. I suspect that every hood unit that Dacor made with this control board is also defective. We have had to replace the halogen bulbs with great regularity. We have halogen bulbs in our boat that have lasted at least 15 years. There was another complaint on this board that had a similar problem with the vent hood. He decided to fix it himself. He is an Electrical Engineer his comments are worth reading and speak to the inadequate design of this unit. It is a shame that the Dacor appliances appear to be near the bottom in terms of reliability. Consumer Reports that their gas cook tops appear to be the least reliable. It looks like I have something to look forward to. Needless to say, I cannot recommend Dacor to anyone. In fact, I would recommend that they not purchase any Dacor product that does not have a full multi-year warranty.

We used a new Dacor range vent only to have it go on and off. We called Dacor and they referred us to Desert Tech in La Quinta. The owner came out and said we needed a new unit for $775. We said just unplug it. He charged us $275 even though it took him less than 30 minutes. Stay away from Dacor AND Desert Tech!

I have owned a Dacor microwave for about seven years and is so far the best microwave Ive ever owned. It works great every time, has great preset features and also has a great sophisticated look. I would recommend Dacor appliances based on my experience with this microwave.

We purchased a complete kitchen with Dacor Modernist stainless steel look. It has been a complete disaster since install day. The first week the Dishwasher flooded my kitchen causing water damage to my brand new kitchen cabinets. There was a seal issue. My ice machine has been worked on 6 or more times. They have replace every part in it and still doesnt make ice or if it does it freezes in to one big block of ice. My microwave combo oven just broke again today with same error code as last time. They had to replace both motherboard in the oven and microwave. Tomorrow they are coming because my dishwasher never completes a cycle. It shuts off at 16 min left. I have been asking for replacement units or better yet take it all back...I would not recommend Dacor espcially how much we paid... over 30,000.

I purchased my Dacor Epicure Range 8 years ago when I remodeled my kitchen. My other appliances were made by GE and Bosch. Ive had to service my GE appliances a couple of times in the last 8 years, but it is the Dacor that has given me the most grief and it was the most expensive appliance purchased. It has never been reliable with regard to convection baking. Initially I thought it was my inexperience with a convection oven. I read everything I could get my hands on and kept trying...after talking with a friend who does quite a bit of baking I realized its not me, its my oven. Then the real problems started. First it was the broiler/ignitor, next it was the membrane in the keypad. Two months later it was the relay board and this time it was the broiler/ignitor....Again! Started calling Dacor when the relay board went out because at this point I had spent $1,000 on repairs....after I had paid $4,000 for the range itself. For the last two repairs Dacor has paid for the parts, while I paid for the service call and labor. This has reduced the cost of my last two repairs by about 50%, which is very helpful. However, Im still very disappointed in the product. I spend a good deal of time in my kitchen and do quite a bit of baking, cooking, and canning. I thought that if I spent more money and bought a high-end appliance, it would serve me well. At the rate that Im going, I will need to purchase another range, unless I want to keep throwing money into repairs on this one, which I dont. I will not ever purchase (or recommend) another Dacor product again.

This range was installed in January 2003. The door on the larger oven was replaced soon after because it would not close tightly and still doesnt with the new door. I have always thought that the oven temperature is lower than it should be but have been told twice that it is accurate, tell that to the turkey. The heating element on the large oven was replaced 2 years ago. Four of the burners dont light and have to be lit manually, this has been going on for 10 years. The relay board has burned out and now has to be replaced, $800.00 fix. The technician just left and could not replace it, he couldnt access the tight spot that it was in and wanted to cut the barrier panel to get access to it. He decided not to do the job and told me to call Dacor to get another repair service, which I just did. I was prompted to write this after reading other reviews and remarks. I hope this helps someone out there to buy a different brand.

Wow! I wish I had read this website before we built our house 3 years ago. I have a 5 burner Dacor cook-top that has been nothing but trouble since day one! I have 5 different appliance brands in my kitchen and the Dacor is the only one that has caused continuous problems. I was so mad at the repair man today I hung up on him (poor guy, I see now Dacor is the problem). The cook-top has exploded three times. ow when I say exploded, I am not joking at all. I mean the explosion blew the cook-top up and burners off, blew the cabinet doors underneath open, flames shot out and the house shook. One of the times, my one year old son was standing next to it. I was so upset I ran into the other room with him and sat on the floor and we both cried. It was terrifying! I have had a repair man here 6 times over the last 5-ish weeks (Yes, I didnt have a stove over Thanksgiving and I was the host; its not looking good for Christmas either and we have 4 kids). They have replaced, cleaned and fixed everything possible. They then pointed the finger numerous times at the propane company (which they now have determined it is not a propane problem for sure). Today the repair company called me (by the way, they have been constant contact with their Decor rep Rob about the problems) and said they are done. My expensive 3 year old cook top is not repairable. They have exhausted every possibility. They have been here 6 times and the propane company three times. I have a hole in my granite counter top cut specifically for the cook-top and am told that every cook-top is a different size so I do not know what I am going to do. I called Dacor today and asked to speak to someone who could help me to no avail. I then asked for someone (anyone) to call me back today. You guessed it. Theres been no call back. This is getting really old. How many weeks does this need to go on (dont answer that)? Another problem that I have just lived with is that the stove continually clicks for quite a while after you are cooking. I was told to clean it a certain way. I did that and it didnt work. The repair man did it; it didnt work. The repair man said something was loose inside and tightened it. It still didnt work. I guess I could live with the click. It is the explosions that I need fixed.

Updated on 02/23/2021: Its been several weeks since I first posted. The only reply that Ive received was an email via this site that requested information from me on my claims. The info was provided the same day. A week has gone by since I provide the information and I have yet to hear back from Dacor. Not even a were looking into your issue. What I did receive was a notice from Samsung (who has acquired Dacor) telling me that one of my service tickets has been cancelled. I dutifully called the listed number to get more information... only to be told that the Samsung customer service rep could not help me and that I needed to call Dacor. Ive tried to approach this matter with humor up to this point but I am out of patience. Given the price I paid for these products, I expected a premium customer experience... the experience I have received has been abysmal.Original Review: I did not think that a customer experience could be this AWFUL or that a vendor could seem to care less than Dacor cares about resolving my issues. After 5 months, the exhaust downdraft that we purchased still does not work and Dacor either does not respond or - when I can get someone on the phone - I get any number of standard excuses (parts shortages, Covid, port backlogs are delaying deliveries, the integration with Samsung, etc, etc). I am also missing basic parts such as shelves(!) that should have been installed during the original installation. The retail partner (Specialty Appliance) does not seem to have anymore luck in getting answers.

I purchased my Dacor Distinctive #DT0127 wall oven in 2015 and have been very pleased with the product to date. However after running a self-clean cycle the oven does not work which was a surprise given the fact that I had previously done self-cleans before without any problems. I immediately contacted Dacor customer service who were amazing! The CSR that I spoke with kindly extended my warranty until 2018 even though I had not registered my oven with them upon purchasing it. He also arranged a service call for me that would be covered under the extended warranty. I am very impressed with the companys attention to service as I really love my oven. Even though I experienced this issue I would still recommend this product.

Dispenser spits out ice cubes onto wood floor everyday. Told it is design issue and nothing can be done. We have to constantly check the chute is empty after used but we can be nowhere near the fridge for hours and hear ice pop out onto floor. My grandson has tripped and fell and me also. Im more concerned for safety than anything. Also our hickory wood floor is concern.

When my husband and I built our home 11 years ago, I splurged and got a Dacor ERD36 36 dual fuel range. During the process of our build, our builder dropped my range during the installation. Dacor was very quick to send out a servicer to make sure the performance of the range was not compromised. The only thing that needed to be replaced was a bent bullnose in the front and the kickplate. I have had one service call in 11 years, which was last year after a brownout in my neighborhood caused my clock and oven setting to go crazy. It had nothing to do with function and had nothing to do with shoddy manufacturing. I just got it fixed and continue to use my range every day. I am looking to expand my island because I need another oven and I am very excited to add a Dacor oven to my home with zero hesitation. I am looking at a DO130S. I would buy Dacor over and over again!

The problem started with our refrigerator unit when it was still in the first year of a 2-year warranty. We have had over 9 service calls for various problems; we had to replace the circuit board, switch and the pan twice. The warranty runs out soon. After five unanswered calls to the customer service number, we were finally able to get through; not that it made a difference. Their response was, “We apologize, but there is nothing we can do?” Sound familiar? Dacor refuses to extend the warranty even though the problems seem to be bad design, parts and customer service. Dacor says when (not if) you need another repair, well work with you. Yipee! We get to work with them some more and pay for the privilege. Dont make the same mistake we did. We will never buy a Dacor product again.

Our dacor appliances are 8 years old. Four or five times a year we need to have the technician to come by to fix something in our kitchen, dishwasher, built in fan for our stove top or refrigerator. These items are high price items-- should not have so many problems.

We acquired a $7,500 Dacor refrigerator when we bought a house this year. The fridge was only 5 years old. First of all it made horrendous noise when operating. Secondly the ice maker didnt work. Thirdly the freezer cooling unit died last week. How can a $7,500 refrigerator be designed so badly? I found out through Dacors authorized service company that it was quite likely the freezer could be fixed with a $400 part and some $250 in labor. The technician hinted that this problem was quite common with Dacor refrigerators. I contacted Dacor and suggested that their Internet reviews were terrible and they should help defray the costs of their premature failed unit. I was thinking that for a 5 year old product they should reimburse 50-75% of the total cost to repair. They said they would give me a 25% discount on the retail value of the parts only. In other words - I would be on the hook for at least $600 of the estimated $700 fix. This was a slap in the face. They dont seem to realize that their companys future business is only built on satisfied customers. I cant believe such expensive equipment can be so poorly designed and supported. Mercedes Benz... they are not. Lest anyone think that I am a frothing upset complaining consumer - I will tell you that I am currently retired, and formerly CEO of a $200 million public software company. I know something about building a business and I know something about focusing on customer satisfaction. I would urge anyone reading this review to stay away from all Dacor products. The Company has shown itself to be undeserving of any American consumers business!

I have the same problem Judy had last week. I have a 36 inch under counter oven. I use it all the time. I have had it for about 10yrs. In the last year the computer has been replaced 3 time. The first time it cost me $600.00. 6wks later it was replaced for free. Now the oven is having the same problem. I hope Dacor makes me as happy as Judy.

We bought the Dacor Wall Oven (ECS136SCH) in 2006 during a complete kitchen remodel. In 2009, the relay board was replaced twice. The first time, it was over $500 to replace. The second time, it was covered under the parts warranty when a terminal was bad. Now, I need another relay board and a new element which will cost over $700 to replace. For an oven that was originally over $3000, this is not acceptable, but what other choice do I have? The technician told me that Dacor has the worst mark up for replacement parts. I thought I had done my research and found that Dacor had a good product. I guess I was wrong.

My Dacor wall oven does not heat. It is 6 years old and barely used. The technician is waiting for Dacor to get back to them to fix the problem. The technician has done everything they can and it has been four months and Dacor is not responding to fix the issue as its a Dacor problem not a technician problem. (Its a control interface issue, the relay board communicating with machine is not working properly.) I have done my own investigation and they do not reply to customer service e-mails, there is no phone number to talk to someone who could help, just a receptionist who says after 7 years we dont fix Dacor. Again, my oven is 6 years old. I would not purchase this high end product or any product from Dacor ever again.

We purchased a Dacor wall oven when we renovated our kitchen in 2010. After five service calls, a replaced circuit board and broiler element, they found a broken wire which must have happened during clean cycle. I have been without an oven for two months and would not recommend buying a Dacor oven because I think it has a faulty design. The issue is still ongoing.

We purchased a Dacor induction range 5 years ago which cost $5000 plus installation parts and service costs totalling $10000. Two days ago, an error code showed up indicating that the generator needs replacement. I contacted Dacor who states that the part is discontinued but that I could contact a refurbishing company (Corecentric) to send my generator to for possible repair. A service technician would have to remove the generator, I would send the part to Corecentric, then IF they can repair it, the tech needs to reinstall it. There are no service providers that Dacor referred me to that will service a refurbished part. Even if I wanted to try, I as an owner, cannot remove it myself because Dacor does not provide the service manual to do so. I spoke to Dacor multiple times about this problem and management stated that since the product is so out of warranty that they cannot offer any other repair option, compensation, or replacement even if the part is deemed unrepairable by Corecentric. When you pay $10000 for a product I expect it to last more than five years and that a reputable company would stand by their product and service. Essentially, Dacor inferred that we are out of $10000 because a part that POSSIBLY can be refurbished for $215 plus service costs, cant get serviced and Dacor takes no further responsibility. I have heard stories from appliance providers and service providers that since Dacor joined Samsung, that their customer service is poor and products have become inferior.

In 2010 we purchased a new Dacor Epicure Stainless Steel 42 refrigerator/freezer. Weve had to replace the freezer heating element (twice) because it fails and then the freezer ices up causing the system to stop cooling. This past week the fan began making a noise and so we had repairmen come out (yet again). Technician confirmed that the pan motor (fan in freezer) has failed. NO PART is available... I couldnt believe that parts wouldnt be available for a $10,000 high-end refrigerator that was purchased new only ten years old. I called Dacor directly and asked them how long they make parts available after they retire a model.The Dacor representative told me that they make parts available for 7 years. 7 YEAR PART AVAILABILITY ON AN APPLIANCE THAT SHOULD LAST 15-20 YEARS??? RUN AWAY FROM DACOR. Obviously customer service is low on their priority list. We will be replacing our gorgeous $10,000 ten-year old Dacor refrigerator/freezer (now a boat anchor) with Sub-Zero. Not too much more money than Dacor but they continue to make parts available for twenty years following model retirement. That is the kind of company that I want to do business with.

I could have written every one of these negative reviews. Ive had all the same issues with my Dacor Epicure oven. Faulty computer panel, failed motor in the downdraft fan, oven not maintaining temperature (meaning NOTHING cooks correctly in this oven), burned out lower element and discolored interior. And let me add that the interior oven fan stays on for about half an hour after you turn off the oven. What purpose could that possibly serve???? Suffice it to say that this is a poorly made product by a company that has no desire for repeat customers. I am currently working with customer service to try to get my oven working for Thanksgiving, but I just dont have much hope after reading all of these similar issues. Clearly, they manufacture a sub-standard product and sell it at premium prices. Nice business model, for a while.

We had misfortune of owning whole suite of Dacor appliances for about two years now -- Cooktop, oven, microwave, and hood. The Ovens motor burnt out after few months of operation - This was covered and repaired by Dacor. Now Cooktop - Dacor Distinctive DRT366S/NG - just exploded with fire when we were cooking one night. This was very scary and dangerous situation. Dacor acknowledges that there was issue with this particular unit but they will not look at it or help us fix it. If you pay 5 times the price of a regular cooktop you would think that a company would have integrity to look into cases like fire and explosion to make sure these things not happen in the future but when they even refuse to look at the issue that tells you that they do not care. Imagine if GM/Ford told their customers that manufacturing faults are not covered anymore since the cars are out of warranty. This has been worst experience ever and we will never ever buy or recommend buying Dacor appliances.

I have a Dacor 27 inch wall (model EOR) oven which I bought 2 years ago, along with a micro and a warming drawer. Since then, the control panel has been replaced twice. Both times because, after using the timer mode, the beeper would come on at all hours of the day and night. In both instances, I had to cut the power to the oven until the replacement part arrived. I am presently waiting for the third panel to arrive. Today I needed to bake something, so I turned the power to the oven back on. Now it will only function at 350 degrees and only in the bake mode. No other numbers can be put in and nothing happens when I select convection. So far Dacor has absorbed the cost of the parts and repairs, but that does not mitigate the hassle of having to wait upwards of 2 months for a part each time this happens.

We have a Dacor Epicure 36 six burner range. It has been a regular source of trouble since it was installed as part of a kitchen remodel in 2006. The igniter for the broiler went out 18-24 months after we got the oven. A year or so after that the weld that holds the bottom oven rack bracket to the oven itself popped loose making it impossible to use the lowest rack position in the oven. Last year the circuit board that controls, among other things, turning the bottom oven element on stopped working. Not only is the board itself quite expensive, but it is buried deep under the top of the stove taking lots of expensive hours of repair time to remove and replace. And now the burner igniters have begun to over spark (e.g., continue to click long after the burner has been lit, burners sparking that have not been turned on). The repairman tells me that is a different circuit board so we could be heading to another $500 or so in repair bills or perhaps a trip to the dump and a much cheaper replacement range. We have had other Dacor equipment (cooktop, wall oven, warming drawer) and have not had a problem with any of them. But given our experience with the Epicure I cant imagine ever buying another.

This will be the third service call on my Dacor Built-in Refrigerator with the freezer making icicles and the fan making a loud noise. On top of that, I have two light bulbs in the freezer that went out from the ordeal. From my review of the complaints here on Consumer Affairs, I see Im not the only one with this issue. This is a yearly problem, and I hope Dacor would step up and resolve this for me since it truly is a poor design issue and no fault of mine.

We purchased a Dacor oven stove top. It is about 10 yrs old now. 3 years ago we had a problem with the ignitor and had it repaired and paid over $200.00 for the repair. 3 Years later we are experiencing a similar problem with the ignitors clicking on and not turning off. I have called for repairs on this but expect this will cost me some more money. I have been online and have seen similar complaints leading to believe that this is a common problem and I would avoid purchasing Dacor ignitor products for the stove top, until resolved.

We moved into our home in 2012 and have had nothing but problems with our Dacor refrigerator (Dacor Model EF48DCBSS). Our issue is the drain pan heater AGAIN. This problem is, water that collects in the drain pan freezes and eventually builds up to a point where the fan motor starts hitting it, sounding like a helicopter landing in your kitchen! Weve had this problem repaired THREE times by TWO DIFFERENT repair companies to the tune of $1000. Both repair technicians said it was a design flaw and this problem would continue to happen regardless of how many icing kits were replaced. So a $7000 refrigerator will cost us $1000 a year to keep running?!?!?! After much research, its apparent we are not alone with this problem. We also had a Dacor microwave just STOP working (model #DMT2420S). It was only 8 years old. Our Dacor oven range (model #ER48DSCH) has two ovens and only one side retains the heat. The main side gets to about 300 degrees and then the temperature starts dropping. Here is the breakdown of costs for our so called high end appliances. Dual Fuel Range - $10000, refrigerator - $7000 (annual repairs of $1000), microwave - $500 (had to purchase new microwave $600). PLEASE LEARN FROM OUR MISTAKE AND DO NOT PURCHASE DACOR APPLIANCES. We have a refrigerator/freezer that we bought from Sears SIXTEEN years ago for $500. Still works like a charm! And thank God we have it, because it has had to be our backup for our $7000 Dacor.

We purchased a Dacor Epicure dual fuel range when we built our house 7 years ago. It was the most expensive appliance we bought and we wish we hadnt. We have had no problems with the stove top, but the oven, specifically the broiler unit has been a consistent problem. We rarely use the broiler and use the oven perhaps 2 or 3 times a month. Yet, the igniter had to be replaced in March of 2008 and again, in June of 2010. In January of 2011, the broil gas valve was changed and now in September, the broiler is again not working. I cant see pouring any more money into this appliance and will sell as soon as I find a buyer willing to take a chance on it. We have been greatly disappointed in this product.

This is an update on my posting regarding our ER36DSCH/NG posted Dec 30, 2013. A Dacor representative has been in contact with us and has offered to install a new oven control which they think will resolve our problem. We are absolutely thrilled and quite surprised that they are footing the entire expense. Now this is what I call good customer service! Thank you Dacor.

I would never buy another Dacor product. The microwave totally crashed and now the oven will not heat. I have had contact in the past regarding repairs and they are outrageous. I plan to replace both items rather than paying unreasonable costs. Very unhappy.

Updated on 05/12/2020: I wrote a review of our Dacor kitchen and gave the company a review of 2 stars because the cooktop, ovens, and hood blower all have failed at some point. The real issue is that the company doesnt support products after sale to quote them they do their best... The other problem is this site, it allows companies to claim they are or have resolved issues, without a response or comment from the customer about what the Companies Resolution entailed. Sending me an e-mail that says sorry the thousands of dollars you invested in our products only bought you up to 7 years of replacement parts, isnt what most people would call a Resolution. After months of working with the retailer and Dacor the e-mail below is what they consider a Resolution:Subject: Dacor customer service **Hello Mr. **, We would first like to thank you for staying a Dacor customer for as long as you have and would like to apologized for the inconvenience. As a manufacture we are constantly innovating products and at some point parts and units do become obsolete. Dacor does provide parts for as long as we possibly can. Once the appliance becomes obsolete we are only required to hold parts for up to 7 years. We again thank you for being a Dacor customer. Be safe during this pandemic. Have a great day. DENISE ** | Customer Service RepresentativeO: (833) 353-5483 x** F: (626) 403-3130Original Review: We built a new home in 2003 and purchased Dacor Preference appliances. Including a 6 burner cooktop, double 30 inch wall ovens, warming drawer, a microwave, and large hood with a remote blower. All the appliances are stainless. We enjoy home cooked meals and prepared at least one meal a day. Our kitchen is a work place not a show place. So these are my feelings after 16 years of use.The Cooktop has plastic knobs and a rubber gasket under each burner and piezo electric igniters. All of these items have failed over the years. I replaced the burners some years ago because when the gasket fails the burners sputter and liquid spills leak into the bottom of the cooktop. Replacement burners fixed the problem for a while but the burner design makes this a point of failure. Additionally, the burners were expensive so were back to sputtering burners and disassembly for cleaning. One of the plastic rings under the flame control knobs broke, weve ordered a new ring ($26) a couple of months ago but Dacor cant give us an estimated delivery date. For the past few years the Piezo electric starters only light half the burners, (they spark but the burners dont light) not a big deal but these are high end appliances, using a match to light the burners is definitely 1950s.The 30 inch double ovens are a great size for bakers like us. The Convection feature is great. However, the first time we ran the self cleaning cycle on the upper oven the door handle on the bottom oven bubbled and melted. The real issue with ovens today, is that Dacor has stopped making replacement parts including the electric heating elements. So even though we spent nearly $3,200 for these ovens, Dacor no longer supports them.The Microwave never worked correctly and we replaced it almost immediately. At that time Dacor used relabeled Sharp microwaves. Finally, Im not a fan of cooking smells in the house. So, we purchased 48 inch hood with a 10 inch inline blower. This week it failed. The motor hums but the fan doesnt turn. So replacement parts? Nope. If you decide to purchase Dacor be aware that the company doesnt provide support for their products in the long term.

Purchased Dacor Induction Range w Convection Oven RR30NIS-C in October 2013 and LOVE this range. Accidentally broke the glass on the induction cooktop with falling object mid-March 2020. Only the glass is broken, and all other electronics, induction burners, oven, etc are functioning fine. Called Dacor support to acquire part number for a glass top for repair - obtained part number #701751 superseded by #702285, BUT was informed that the part had been discontinued and is no longer being manufactured or kept in stock. No other advice was given other than to discard the entire $6000 range. Multiple phone calls with service.I asked for a listing of third party part distributors and was referred to four distributors on the Dacor public website and given no other info. I called all web-based third-party distributors I could find in USA and Canada to see if anyone had the part in stock, with no luck. I contacted two technicians to see if they would be able to obtain the part through their channels, with no luck. I am an engineer, so I spent some time pouring over technical manuals trying to find a solution to replace the entire induction range cooktop assembly (top part of the range) with a later model, and although its possible, Dacor would not provide the ability to purchase an RNR30NI range cooktop assembly that could be fit into the existing housing on top of the range. The convection oven is completely fine, and I cannot believe that Dacor has given me no other option but to pitch a six-year-old $6000 range because they stopped manufacturing one fragile part made of glass. I would imagine that many consumers may be in the same position as I, as these cooktops are breakable, and accidents happen. I have reached out to Dacor support desk numerous times without resolution, and I am at my wits end with a $6000 boat anchor in my kitchen. What a waste of money! Poorly done Dacor!I would like Dacor to provide me with some sort of solution whether it be the part required to fix my induction cooktop, or a replacement Induction Range with convection oven, or reimbursement of the purchase price so I can obtain a replacement on my own. If I am not able to find a solution to repair my range, I will never buy from Dacor again! Dacor will discontinue easily broken parts without warning! You may spend thousands of dollars and not be able to repair your appliance after warranty expires!

I purchased entire kitchen of Dacor appliances - $30,000. The 48 refrigerator required 9 service calls to stop freeze up. Wall oven – the digital panel went bad. Stove top exhaust – the circuit is melting. The dishwasher had 17 service calls over 2 years - mid way they replaced the unit because they could not stop it from leaking and damaging our wood floors. The most recent service call was yesterday, 12/20/2011. After waiting since November, it is again not working. Does anyone else understand that spending $1700 on a dishwasher should allow you to use the dishwasher? I called the customer service and was told We are discussing the situation and will get back to you. Are you going to come wash dishes with me over Christmas when we have 25 guests? Were you there on Thanksgiving? If I hadnt been stupid enough to buy all Dacor appliances, I would throw it in the dumpster and buy a GE from Home Depot.

I have owned a Dacor Convection microwave for a few years and is so far the best Ive ever owned. It works great every time, has great preset features and also has a great stainless steel look. Great Product.

Our initial dishwasher had many problems. After several service calls, we called Dacor to identify the issue and see if there was anything they could do for us. We received a brand new dishwasher (even better than the initial one) for a nominal cost. We would like to thank Dacor for their excellent service and attention. Its not always the issue, but the resolution that makes the difference.

We purchased the modernist collections 48” range, refrigerator and freezer, oven and microwave combo and dishwasher with a kitchen remodel 9 months ago. We had one issue with the dishwasher which was resolved, then another when is stopped mid-cycle. Repairman came out and was told we needed a new panel. Found out it was back-ordered. Well, it’s now been FOUR month without a dishwasher. We have contacted customer service and asked for other options and were told there was nothing they could do! When following up we have left messages and had our calls not returned, as has our service company. I have waited on the phone 3 times 30 minutes to talk to someone, because they won’t call back. We’ve asked to talk to a supervisor, and was told our information would be forwarded... 2 days later, no call. This is by far the WORST service I have ever had for ANY type of product.

Ive had the pleasure of owning a PGR30S range from Dacor for the past 20 years now, I must say it has past all my expectations on performing in the kitchen. This unit cooks everything amazingly well... Thank you Dacor for such a great range.

We bought our house in 2010 and our Dacor stove was supposedly newer. When I went to clean it, I found loose screws in the bottom. Apparently, the convection element is loosing its screws and washers. Ive had this appliance fixed once already when the cooktop kept clicking. The black plastic around the controls cracked mysteriously. It takes 3 hours longer to cook a turkey than it should. This is a strange stove, which supposedly cost a lot. I wonder if a convection part missing two screws should be used?

I purchased my Dacor range in 07. After running the self clean cycle today, my oven wont heat up using convection or regular bake. Keep in mind, I had the entire electronic guts of the oven replaced in March 2011, 6 months ago after the same full failure. I paid $6,500 for this appliance. I wish I had my old GE oven back. This piece of equipment is only 4 years old. My husband and I dont use the oven often. What a huge disappointment! I will likely spend the next few days on the phone with customer service.

I completely gutted my kitchen on 2/22/92, and purchased a Dacor CPD230R double oven. Whenever I used the self-cleaning function the next day, F0 would appear. I would have to get a repairman to come to my house. This cost me a fortune. For one year, I just used the bottom oven. I finally called Dacor, and complained. I wrote a letter to Mr. **, and wanted satisfaction.They decided that I could purchase a new, better oven for $1,480.00. This was 1998, so in 6 years, I spent $3,680.00 for 2 ovens. After 5 years, I started having the same problems. Every time I used the self-cleaning function, F0 would appear. I just totaled my bills for the new, better oven, and I have spent $963.00 and it would be more, but I figured out, if I pressed cancel and held it, the F0 would disappear. So every time I used the oven, that is what I did. This would last for 8 months. The oven completely shut down, and I could not use the top or bottom. I just had a repairman here, and he said i need a new membrane assembly, and latch. They were supposed to call me with an estimate. They just called, and said the part is no longer available. This is upsetting. Reading the reviews, I see I am not alone in my dissatisfaction with the Dacor oven. Now, I will be redoing my kitchen.

I have 2 single ovens side by side and have a cooktop and ventilation system - my experience with the cooktop and vent (2000) was so good that I did not hesitate to buy Dacor MorS130S ovens. They were installed in my new kitchen in September of 2012. I had my cooktop and ventilation system reinstalled. My daughter accidentally cleaned the oven without taking out the GlideRacks (which are hard to take out). We oiled them, etc., like the manual says if they are accidentally left in - they will not glide at all and now I am being told $300 each to replace excluding the cost of the service call. This is ridiculous. What kind of design is so poor that racks would get in this condition? I had Bosch ovens before and their warranty was wonderful and I, luckily, bought a Miele dishwasher which has a 10-year warranty. I would not buy Dacor again because of the warranty and because of this problem. I am beyond disappointed as I love my cooktop etc. I feel that Dacor should at least pay for part of these GlideRacks.

I went to put something in the cabinet at the top of my built-in wall oven and noticed the cabinet door was warm. Then, I noticed the heat was coming from the top of the oven at the control panel. I am afraid of a fire breaking out in the cabinet now. The oven is less than a year old. We just remodeled our kitchen and installed the ovens in May 2012 and this is just June.

Add me to the Dacor hate list. The $4300 oven installed in 2000 is now a whopping $6400. My motherboard #2 is broken and the glass on the door cracked which to me is a safety issue. This is a two adult, no kid household so figure. We use the oven about 7 times a year. My Dacor rangetop and hydraulic exhaust have both required service as well.

DCT305SNGH - I have owned this stove for about 3 years already. From the very beginning it has been trouble. The lights that turn on when a burner is on broke immediately. The place where the gas comes out and ignites is black and hard to clean. The grates are rusty, the finish has come off. The indicator knobs dont reflect what is happening in other words if it is on the lowest setting you dont have any indicator marking. It is hard to clean and scratches very easily. I have had the service person out about 5 times until they decided to send me many new parts. These arent any better. It is just a bad product. Basically the warranty is useless if you keep calling for the same issue. They say, This is the last time we will fix this issue. Sadly I always heard this was a great company and I waited 7 years to save up for this stove and boom rotten appliance.

We purchased a Dacor Oven model # ECS 136544 in 2009. Within two years, the relay board and thermostat in addition to an LED bulb required replacement. A year later, the broiler heating element and the second LED light required replacement. Dacors response (800-793-0093) was read your explicit warranty and the implied warranty under Section 2-314 of the Uniform Commercial Code isnt applicable. The total expense for repairs is over $1,000. Did we get a lemon, or are Dacor ovens prone to failure? Should we have been thinking Wolf?

Replacement light for the oven - I could not find anyone that carries the halogen bulbs for my oven and called Dacor parts line. The bulbs come in a package of two. They were $79.95. I was told I should have called two months ago, that they were $29.95. So would I buy another Dacor Appliance? I think not.

We purchased a Dacor 30 Heritage Gas range and installed it in early Oct 2020. Within a day a gas leak from the back of the range was identified by our gas contractor. Dacor repaired it quickly (12 hours). I was impressed (though concerned it already had an issue). In December 2020 I noticed that the oven indicator light was not coming on. I contacted customer service and despite indicating that there was a problem, was simply told what the light was for. Then, in February 2021 (under 5 months after installation) the oven stopped working. The service technician indicated it was an electrical issue and the gas would not ignite. It has now been over two weeks and we still do not have it repaired nor any indication of when it will be repaired. We spent $5200 on this range. I do not recommend Dacor.

Warning: Warning, safety hazzard for all, adults and children. Recommendation: The knobs should be set on the top of the stove, not the front where children can reach. Control knobs should click when fire and gas is turned off, and highest flame setting should be at the end of the turn just like a clock. I inherited this range as new owner of the house. Today I used the high flame option of the gas stove. When I was done with cooking, I turned off the gas according to the knob position, front of the turn. Later I discovered the range was not exactly off. It was still hot but no flame could be seen.I checked by sight the control knob position, it was set incorrectly in off. Then I touched it and realized the knob actually has a bit more to go to the end, slightly before the off position. Therefore it continues to release gas with unobservable flame. This knob does not click when user turns it to the off position. It is just a silent knob with an inaccurate cue of a heavier black line for off and on indication. Besides, high flame setting comes at the beginning of the turn of the knob rather than the end, it is counter intuitive to our mind of increase heat by turning the knob further on, like our clock. Oven racks are hard to put back after cleaning. Once a rack almost tumble out while food was sitting on it.

Very pleased to say Dacor replaced our oven with a new one! I havent thoroughly tested it all out yet, as it was replaced the day before we left for a trip. But so far the top oven seems to be working properly. Need to use the bottom oven yet to check it is working properly.

I was and, I repeat, was a loyal Dacor customer. I gutted and rebuilt a kitchen 9 years ago and purchased a Dacor stovetop, oven and microwave. I remodeled my new house 5 years ago and again purchased Dacor stovetop, oven and microwave. Consumer reports provided favorable reviews of the appliances I purchased below.First red alert: The oven Model MORS130S and Microwave Model DCM 24S LED did not match. The microwave was green; oven was blue. The brochure was in black and white so there was no way of knowing that aesthetically they were a mismatch ... it was very sloppy(!) and very deceptive by Dacor. I mean when I waited weeks for my appliance order and the oven is already installed with a big fat ugly LED screen, what was I supposed to do, yank it out and start all over again? This was disappointing!Next, I was simmering chili on the stovetop (5 burner, gas) and, lo and behold, 18 flames started exiting through the turn knobs resulting in a meltdown. The gas was leaking through the tubes underneath the stovetop. I just happened to check the chili while I was gardening to watch the house almost burn down and btw, it was difficult to put out the flames because the natural gas was leaking under the unit. Seriously! I called customer service and they got hopping right out to fix the issue. This scared the heck out of me. It is negligent to have a product like that on the market.After about 13 months into the life of the Model MORS130S oven, the touch panel failed emitting a CO1 error message. I was told it was $140 to fix it and that the panel was defective, great quality there, Dacor. And the added joy to the CO1 error message is that the unit beeps intermittently all day and all night long unless the power to the oven is killed. Joy... now another issue - Model MORS130S oven LED lights are burning out. Seriously, what else will there be? Now its $175 for LED panel and another $100 to install by an authorized Dacor service man.So I called Dacor back again today because the LED light out was annoying me. They offered nothing. To be fair, my appliances are out of warranty but seriously, Dacor nearly burned my house down. They should be winning me back as a customer if they really cared about their customers and having long term repeat business. Never again, Dacor, never!

The functions are useful and so far everything works the way it supposed to. No real complaints. Convection and baking features are really useful when it is a small thing to start an oven. Easy to operate. Everyday cleaning is easy as well.

Talked into spending $4700 on a wall oven on the recommendation of an appliance retailer. My concern was even baking and reliability. Was told I would be very happy as Dacor was best on the market. Well long story short, it never cooked evenly and after 8 years quit working. Had to lug the heavy oven to the city to an approved service provider. They thought it was the relay board (told the brains of the oven). Service provider changed several things (sensors, board and whatever else). Nothing solved problem. Phoned me and said I was looking at minimum $2000 and up. He threw oven in garbage. We didn’t even send the gas money to bring the dud home.Thought it should last longer than 8 years. I phoned Dacor. They wanted to know exactly what the problem and diagnosis was so I told them to phone the Service Provider. Said they would but I had to email copy of receipt which I did. A couple of months gone by and never heard a thing and they are not responding to my emails. DO NOT RECOMMEND DACOR.

We had problems with it all the time. The front plastic cracked and ended up causing the oven not to work. We have spent (over the past 9 years) about $1,000 on repairs. Now, we just had it fixed and our new clock that was installed into the oven is running fast. After just being fixed, it takes 20 minutes to heat up to 400. Honestly, it always has been that way. We’re not happy with it at all. We bought a Sears brand oven for our church, and it works great, and the cost was only a third of what we paid for the Dacor oven. The Sears brand bakes just as good as the Dacor (when it works). I think it was a waste of money to buy this Dacor oven.

I purchased a Dacor Refrigerator about 4 years ago and have had nothing but constant problems with it over the years. Finally they agreed to send me a new refrigerator, and now after five months I am having a major problem with it, and have been trying for 3 hours to get a warranty authorization from them so I can have a repair man come out and stop a major leak that is now leaking into the condo below me. I am so disgusted with their products and their service that I really would never advise anyone purchasing a Dacor product. If I could I would buy another brand then be done with it, but this was a $9,000.00 refrigerator - CAN YOU IMAGINE THAT???

We renovated our kitchen and as part of this had installed the new Dacor Modernist Fridge and Freezer columns at a VERY hefty price tag. We were going to get a subzero and changed our minds when we saw these products - the styling, design and function looked so much better than Sub-Zero, despite the higher price tag. Well, fast forward about 8 months and we dont have a functioning fridge. It stopped cooling out of nowhere. We had to throw everything away. After FINALLY getting a repair person to the house, they told me that it was because the fridge had run out of gas (freon or whatever the coolant is thats used). When asked how that happened they said they didnt know, but that they couldnt repair it as they needed a part from Dacor. A WEEK later, they finally got the part and came back to repair the fridge. 4-5 hours later it still was not repaired and they said they needed another part. Its been almost two weeks since then and the part has still not arrived. We had a BlueStar range installed when redoing the kitchen and when we had a problem with that, they overnighted the part, so that they could fix it right away. This is not the case here - the customer service has been absolutely horrendous and Ferguson Appliances (where I bought the fridge from) has been at their wits end with this (I cant say enough about how wonderful Ferguson has been to deal with). This has been a nightmare. Now the repair place wont even schedule a repair date because they dont want to lose the time again in case the part doesnt show up again... DO NOT BUY THIS FRIDGE. I should have known better not to buy a Samsung (yes, Samsung bought Dacor a few years ago and these products are glorified Samsung units).

My dishwasher - I used to totally rinse my dishes before putting them in to the dishwasher. No more, not necessary. Does a fantastic job. My refrigerator is amazing. Very roomy, love the individual crispers that keep my veggies perfect and my lunch meats and cheeses perfect. Also, love, love the bottom drawer freezer. Easy to access ice and frozen items. My range is amazing. I love to cook with gas and bake with electric. I bake a lot and this oven is a dream. The green clean feature is long overdue with ovens. Not harsh and cleans beautifully. Bottom line – I’m totally a Dacor fan.

I have an older cooktop. Yes it is 15 years going strong but I have ran into a few issues where I know the repairs would be pricey but especially the parts. After talking to a few representatives, they truly want to help you. Nothing is free and I don’t expect it to be, but I am glad they they helped me get my cooktop back to functioning again. I hope someone finds this helpful before reading or writing bad reviews.

Wish Id known Dacor issues when buying my oven. (Primarily for style - yes, assumed it would function as stated; high end brand). Thank goodness I DID NOT BUY other Dacor appliances. My 30-inch Dacor oven/cooktop burners work but finish started coming off quickly. Above range microwave handle broke within a year. MAIN PROBLEM: OVEN DOOR either wasnt properly installed because it doesnt close flush with unit or its hinges have loosened over the years. Although oven eventually heats, it takes forever. After examining door hinges closely, looks like oven has become unhinged - as have I. No loose parts seen. Recommendations? Other than STEER CLEAR OF DACOR.