We remodeled our kitchen in 2006. I spent a fortune on a Dacor dual fuel gas cooktop with electric oven/convection oven. My Dacor problems seem so normal I mostly deal with it. My 2 biggest complaints are the glass oven door is not airtight, it is darkened between glass, very hard to monitor my baking. And the temp gauge has always been off by 15-25 degrees. I use an in oven temp gauge, which has been calibrated so I know it works. If anyone is planning on a Dacor, you will get the best looking range. It just wont work.

We bought our new Dacor CPS 130S wall oven when we built a new house in 04. First we had to replace the lower heating element. Now the touchpad (Dacor part # 13290S) is malfunctioning. The + button will not respond to touch. Called Dacor and was told that the needed part number was discontinued in 2009. I double-checked with a distribution center in San Antonio, TX, who confirmed that the part is no longer available. They referred me back to Dacor on the chance that Dacor would have one somewhere. Dacors suggested solution was that we need to buy an updated completely new oven, which would cost us several more thousand dollars. So here we sit with a perfectly good oven minus a touchpad to control it correctly. So much for buying reliable, U.S. made products and receiving good service. I thought there existed a federal law that mandates a company must make parts available for 10 years if they discontinue the product?

When I pay top-dollars for a supposedly high-end product, I would expect performance and durability. That is not the case with Dacor. This manufacturer charges top-dollars for their appliances but their products do not live up to expectations. I purchased a Dacor gas cooktop range, and within a year several blue-indicator lights on the knobs (which indicate the gas is on) failed. At that time it was covered under warranty, and even then it was a hassle to get the repair technician to come out and take the range out to get to the electronic parts. After replacing two of the lights, the other lights failed as well, and then the replaced lights eventually went out. Now, only one out of the five lights work. After a year, the appliance is no longer under warranty, and it is too expensive to get it serviced. Its not only a cosmetic issue, but a safety one as well.Were in the market for a single wall-oven, and I considered a Dacor for its clean and stylish design. However, after reading the reviews about Dacor, Im veering away from this company. Sadly, as much as I want to support a Made in America company, the pride of workmanship and customer service doesnt live up to this companys branding.

About a month ago then again 2 weeks ago, I would hear a beep (not while I was cooking) from the stove. I went over and all elements had turned themselves on at HIGH. The only way I could turn them off is to repeatedly push and hold the child safety button. Very scary! If I had left a pot or pan on the range top, who knows what would have happened. It did it occasionally with 1 burner twice more. Yesterday, the range top started cycling every 90 seconds, on then off, then on, then off. I shut it off at the circuit breaker twice thinking this is a way to reset electronics sometimes. Once for 2 minutes then again overnight.I tried cooking on it this morning: on and off and on and off again. It is shut off at the circuit breaker awaiting repairs. I am a renter so am spared the repair bill but not being able to cook (of course it happened on Easter weekend!!) is a major pain. It is 10 years old this week the landlord told me, but I used to cook on a stove that was 60 years old and it worked like a champ.

We have a Dacor gas range RSD30R that we bought to upgrade our kitchen in 2002. We have had several issues with the range to date. The first issue we had with the range was the auto lock for the oven cleaning cycle that failed in 2007. It was not covered under warranty and cost $88. The second item to fail were the oven door springs. They also failed in 2007 and covered under warranty. They failed again in 2017 and had to be replaced for a second time. The springs are too weak to hold the weight of the heavy door. $68-$78 for the springs. The springs could easily be changed out as the brackets are still good but they only come as complete units. The last item to fail were the ignitors. Only one ignitor failed out of the four but as the spark module ignites all burners every time any one is turned on, premature failure could be expected as all ignitors light every time. This time the part is no longer available from Dacor. Dacor does not support any products they build after 7-8 years. Parts will no longer be available. I would not recommend Dacor Appliances to anyone as the manufacturer does not support their own products very long. I purchased Dacor to buy American and I regret it now. In contrast every product that Miele made even 20+ years ago, parts are still available directly from Miele and other suppliers as well.

We chose DACOR (8-burner double oven top of the line ERD60S06CH/LP) in 2006, new construction because we disliked the signature blue interior of another luxury brand. Last October I detected a gas leak from one of the burners. The authorized repair company was contacted, and the entire unit - all 8 burners and both ovens were out of commission while we waited for the replacement part. Six weeks later the repair guy returned with the wrong part. We had to wait an additional month for the repair guy to return. Apparently, not important that people might want to cook and bake before the Holidays! After the new valve was replaced the oven light began to turn on when any of the gas valves on the defective side was turned on. I write this review 8 months into the problem. I can fix for $700 by ordering a new control panel. I wish I had read these reviews earlier. I overheard the tech say that there was electrical interference and that the wires need to be insulated to stop the oven light from turning on and off. I am so FED up with both the Dacor California head office not caring and the horrible authorized service company. I will take this unit apart myself and fix it. DACOR IS GARBAGE. Go with Sub-Zero, Miele and forget this Brand. DACOR: Dont Accept Crap Or Rubbish! Made in America? Shame on you. No problems with 4 Sub-Zero fridges, or 4 Miele dishwasher the same age.

I rarely write reviews but when I found your site, I decided it was time to vent. I bought a 36 dual fuel, convection Epicure range in 1999. It was not a cheap oven and I was excited at the possibilities of having a 16,000 BTU broiler and large oven cavity to work with. Lets just say that excitement quickly wore off. Almost immediately after the range went out of warranty, the ignitors went bad and we also had to replace the control panel ($400 in repairs was a lot back then). After that, we continued to have ignitor problems and replaced them again. Finally, I just stopped doing it and lit them with my aim and flame. I never allow my children to cook on the stove because I am afraid they will be burned. Most recently, my broiler element, relay board and again more ignitor problems ($1,200 in repairs). Not to mention, the repairman had a terrible time trying to access all the areas and was at my house for 4 hours trying to do so. When the initial problems happened, I emailed, phoned, left message, etc. to no avail with customer service (I use that term loosely). This company is the worst. I have told everyone I know never to buy a Dacor anything. Next time, Ill buy a Wolf.

We have a 2 year old 36 inch, Model EF361WF refrigerator. Water began pooling at the base every 2-3 days. Called Dacor Customer Service Team. Pitiful response and horrible customer service. Had to call private technician who was very surprised that a so-called higher end appliance was not factory-fitted with a P trap. He sees the problem often with cheaper models. Dacor has let us down twice. Buyer beware: sub-standard products matched with sub-standard customer service. Dacor will never get our business again and we would recommend all potential purchasers to consider other brands.

We purchased a Dacor gas range in 2005 for $2000. In a short time the plastic trim around the knobs cracked, and the glass in the oven door had not maintained its seal. I contacted Dacor several times and was told to take a picture and send it to them, then they could decide a course of action. The course of action was that I would pay for materials and labor. I decided not to do that, and eventually I will replace the range with another brand, never a Dacor!

We purchased this high end Dacor range (Dacor Renaissance ER30G) new in 2011 from the Appliance Loft here in Cincinnati. It was dropped off and installed and would not operate right out of the box. A repair was made and everything worked (unless you count the indicator lights on the knobs, they all went out after approx 14 months). This past November the oven went dead. A1 appliance came out: Determined new control board needed, ordered and installed. Thanksgiving Day, oven dead. A1 comes back, reset the High Temp Fuse. Oven dead 4 days later, A1 returns with a new HTF. Dec 22, Oven dead. As soon as The holiday is over we will call another repair shop and start looking at replacing this unreliable piece of eye candy. Open comment to Dacors design engineers, quality control engineers and management. You should be totally ashamed about this product youve designed. You are supposed to represent the best in American design and quality and this falls below that of low end appliances out of China. See you in small claims court.

I purchased the 30" All Gas Heritage Range, the Convection OTR, and the Counter Depth Refrigerator! I am obsessed with all of these gorgeous Dacor appliances! From the brass caps on the range, to the chilled water pitcher in the door of the refrigerator...Dacor has thought of it all! I have enjoyed cooking more and would recommend these products if you are wanting to update your kitchen appliances!

I have owned a Dacor dual fuel 6-burner range for several years. I paid approximately $5,000 for the product. It has proven to be totally unsatisfactory. The gas burners click and make noise whenever you try to turn the burners down to a low temperature. The cook top is very hard to clean. The range is a constant problem. It smells bad, does not heat up promptly, and the broiler feature is always a problem. A gas oven is supposed to heat to and keep a constant temperature - the Dacor does not. The broiler will not cook food evenly or well. The door to the oven will not close properly and is constantly partially open. The hinges do not seem to work properly.Most importantly, I have tried on many occasions to get Dacor to do something about the defective product. They have been totally non-responsive. When I did finally get somebody to come and look at it, they spent about 2 hours cleaning it, accused me of using the wrong cleaner on the cooktop, and presented me with a bill for $800. I asked if they would just give me my money back and take the defective product with them. DONT BUY DACOR.

The functions are useful and so far everything works the way it supposed to. No real complaints. Convection and baking features are really useful when it is a small thing to start an oven. Easy to operate. Everyday cleaning is easy as well.

I purchased a Dacor double wall oven in May 2011 at a reduced price from a secondary market. Due to cosmetic defects, it wasnt sold by an authorized Dacor dealer. I bought it at what I thought was a fair price, considering the cosmetic defects. When our home was completed in November 2011, we installed the oven but found the oven would not heat up to the set temperature. I was told by the company I bought it from that it would be eligible to be covered under the manufacturers warranty. I called Dacor and was told that since I didnt buy it from an authorized dealer, they would not cover it under their warranty even though I had it under one year. Since I had to give Dacor the serial number when I called it in, they now have a permanent record to that end. I have had no oven because I cannot pay to have it repaired.

I called the customer service number regarding my double oven. It just randomly beeps and now turns off. No error code displayed. It has done this on and off since 2003. Now it is happening all the time. I called customer service and they seemed to act like it is my fault and I need a new touch pad. I inquired and this is a recurring problem with this model. I could not get a straight answer from the person I was talking to. He just told me that if the repairman says I need a new touch pad, then I need to get one. Well I have been doing some research and this is a problem that seems to be haunting more people than I. We own a Dacor gas cooktop that has had to have a switch repaired. We own a microwave that has had two new circuit boards and now a beeping oven that gives no error code and turns off by itself. My advice, do not buy Dacor appliances.

We have a Dacor Epicure 36 six burner range. It has been a regular source of trouble since it was installed as part of a kitchen remodel in 2006. The igniter for the broiler went out 18-24 months after we got the oven. A year or so after that the weld that holds the bottom oven rack bracket to the oven itself popped loose making it impossible to use the lowest rack position in the oven. Last year the circuit board that controls, among other things, turning the bottom oven element on stopped working. Not only is the board itself quite expensive, but it is buried deep under the top of the stove taking lots of expensive hours of repair time to remove and replace. And now the burner igniters have begun to over spark (e.g., continue to click long after the burner has been lit, burners sparking that have not been turned on). The repairman tells me that is a different circuit board so we could be heading to another $500 or so in repair bills or perhaps a trip to the dump and a much cheaper replacement range. We have had other Dacor equipment (cooktop, wall oven, warming drawer) and have not had a problem with any of them. But given our experience with the Epicure I cant imagine ever buying another.

I replaced my Thermador Wall ovens with Dacor because the size and I would have to do less retro-fitting of my cabinetry, this was a grave mistake. Here are the issues with Dacor.1. The high heat sensor trips and you need to call a service professional to have it reset. This gets very expensive. I have tripped mine three times, once baking a cake at 350 degrees, once during self-cleaning and another during normal cooking. The Dacor Service Help said this was a common problem because the heat sensor is located near to the touch panel.2. The oven vents from the bottom of the unit into the room heating my kitchen.3. The glass window does not seal so I have stains in-between the panes of glass. Not very attractive to stare at large drip stains.4. It takes an exceptionally long time to pre-heat oven and convection mode even longer.5. The temperature cycles through and does not maintain its cooking temperature causing underdone results and longer cooking times. This is especially challenging when cooking roasts and large turkeys because they may take up to an hour longer than expected.Overall, I do not recommend this product.

The Discovery Model 30 electric wall oven - After 6 years, the oven failed. The fan motor went out and at the same time, we were advised by a very reputable appliance repair recommended by Dacor that we need to also replace the computer or brain. Total cost of repair: $1150 with a warranty of one year.

I wish I had read all these reviews of Dacor products before being duped into paying for a high end wall oven. As many others have mentioned, the electronic panel design is faulty. I paid $1000 to have it replaced once. Now it is broken again and the alarm beeps constantly. The reply from their service rep was that they havent had any recalls of this product (in other words, no ones house has burned down yet). He also admits that he wouldnt buy a Dacor oven unless he had money to burn. Well, my money has already burned and so have I.

I submitted a review regarding a repair on this same refrigerator Dacor EF42BDCBSS back on 10/29/12 and 10/31/12. We now have another repair bill in the amount of $486.42 for a drain pan kit and defrost thermostat. I tried to contact Dacor by phone and email to talk about the situation, but have not received a response. I would highly recommend that you think twice about buying a Dacor brand refrigerator.

I built my home in 2003 and installed a Dacor 30 wall oven. After several years of poor performance, we started to get an error message. Dacor suggested replacing a board for $300. That didnt work so they had me replace another $300 board. That didnt work so they told me I needed a new front panel and it would run about $1,000. That board is on back order and they dont have a replacement date. Thinking that its bad business to sink $1600 into a troubled product that has terrible reviews on the internet. We found out that once you go with Dacor, you need to stay with Dacor due to an unusual, nonstandard size.Thinking that Dacor has improved their product we ordered a brand new $3,000 Dacor RO130 30 wall oven. It arrived promptly and I removed the defective $3,000 oven and put in the brand new $3,000 Dacor RO130 oven. What I got was a dead brick. The Dacor customer service has been awful, and will not allow me to talk to anyone in their technical side. The oven is getting power. Dacor customer service wouldnt help me unless I could prove that the unit was getting power. So I had to get an electrician in to prove that I had properly wired the 4 cords that came off the original defective Dacor wall oven. Get service help? No chance. I live 100 miles from Seattle and no one wants to work on Dacor. So here I sit with a $3,000 brick. No service and Dacor has no clue on how they will service this wonderful $3,000 RO130 30 wall oven that is an out of box failure. I dont see how a company that has this bad of a product, two generations of defective ovens, bad customer service, reluctance from the repair community to work on their products will be in business much longer. If you are considering Dacor appliances, consider the problems that I am having. The nonstandard size of their ovens will lock you into future purchases to replace their products that dont last 10 years.

DONT recommend model #MOH130. We were so impressed with the options that this oven came with. Sadly, with all the bells and whistles also came a ton of repairs. After the 4th repair, our service rep said the relay board needed to be switched out. (Half of the service men who came to my house seemed to be grasping at straws trying to come up with an explanation why the temperature was fluctuating, or why it took so long to heat up, etc.) Then I get to wait 2 weeks for a part to be ordered/arrived and re-schedule service. Last week got code U22 - oven wont even turn on. This oven is only 6 years old. NO THANKS - NEVER AGAIN will I buy anything from this company.

Perfect size burners and small oven. Cooks food perfectly about 25° less than you think. Great grill on top. Easy to clean.

We purchased a Dacor dual fuel oven range in 2008 in conjunction with an extensive kitchen remodel. It was beautiful and expensive. It has had innumerable problems. 2008: One of the igniters broke requiring replacement. 2014: oven stopped working, required new relay board. June 2020: Relay board again broke, oven stopped working. December 2020: Oven stopped working, heating element broke. These were serious problems each resulting in 1-2 months without an oven as the parts had to be special ordered. We have not had an oven since December 2020 (it is now March 2021). We are waiting for a replacement part. In addition, minor problems included a broken indicator light and burner grating. Dacor customer service was only moderately helpful, referring us to local repair companies that had difficulty obtaining parts. Dacor has told us that this should last decades but we are seriously considering replacing it after 12 years because it is very unreliable. I would not recommend a Dacor based on our experience.

We have had our Dacor since 2006 and this range, the most expensive appliance we have ever owned, simply doesnt maintain the proper oven temperature. We have owned several far less expensive ranges and their ovens, much more basic designs, do what an oven is supposed to do maintain a temperature! We cook or try to quite a lot but working with this stove is like baking over an open fire while camping. This supposedly gourmet, fancy, convection oven that supposedly can bake cookies and meat at the same time is a total fail. We have had the service people out repeatedly to no avail. I am convinced we could change the circuit boards repeatedly and it wouldnt make a difference because it is a faulty design. This product should not be on the market or this company and their poor service in business. DO NOT BUY THEIR RANGES! Unless you dont cook and all you will do is look at it. We are thinking about retaining an attorney to file a class action suit. We could buy a low cost oven that works several times over for what we have paid in repair bills.

We purchased the Model MOH130S in 2006 from a very reputable distributor of high-end appliances. In 2009 we required a service call to deal with temperature control. The oven was out by more than 40 degrees Fahrenheit. This resulted in a relay board, item 101559, to be replaced. Dacor was nice enough to cover the cost of the board, but not the cost of the $152.00 service call. In 2013, guess what? Relay board, this time out by more than 50 degrees, item # 101559 required replacement again only this time it was not covered and cost of $628.00. Here we are, 2016 waiting for the service provider again as temperature is out by over 60 degrees. Roasts, Turkeys, Chickens and everything else have been dying slow deaths in this unit and are awaiting yet another bill to deal with temperature control. Dacor will do nothing until another $150 service call confirms the problem. Hmmm! What to do?

Dacor dual fuel 30 inch range - First of all the look of the dacor is second to none in my opinion. The digital screen with blue lighting makes this a truly elegant part of any kitchen..... when it works. The range top itself worked flawlessly for me and the main burner was always more than enough. The problem with the range lies in the electronics. The unit has been in my home for over a year and has worked for less than a month total. An error code appeared when ever the oven gets hot. C33, C1, 0000, 1111, C11. Ive seen it all. I have had the main board replaced twice and my local repairman is on first name basis with even my dogs at this point. The final straw for me was when the oven door glass shattered while cooking and when dacor was contacted they said that happens. Im think Ill try Viking.....

Arrived in good condition and so far works perfectly. Delivery was delayed by one day because of the incompetence of my local mail service. I bought this microwave, as others have described, to replace a 13 year old Dacor that had not really died but had lost the electronic screen. We put magic marker numbers on the display screen where the numbers had been 5 years ago and kept using all the functions. I decided to replace as, without the display screen, I could not do anything semi sophisticated with this microwave but its motor and microwave capacity was still going strong. This model fits perfectly into the previous 24/27 trim kit. Unfortunately our other trim kit is white to match our old microwave. Decor only has stainless steel now. And the new trim kit for this microwave is flat without the vent slats (plus costs over $300!). From the placement in our cabinet, I think the vented slats are really important to dissipate heat and am puzzled by the change in design by Dacor. The slats are a little tedious to clean but as a TV is above the microwave and an oven below I want the heat to have a better place to go. Ebay has the old trim kit in stainless steel but so far the expense seems excessive for just the outside piece. The internal support bracket for the new microwave is exactly the same as for the previous model so the only part of the trim kit needed for my microwave is the outside frame. This newer model works very similarly to the older version. I am delighted Dacor still makes this microwave to fit my space 13 to 15 years later.

We purchased our range (Dacor Dual Fuel Range RSD30) in about 1997 thinking we had a good investment. We have replaced the bezel 5 times (the area that encloses the control area). Today the door glass has cracked. Whooppee! Merry Christmas! Each time I called about the bezel, I was told that they had a design flaw. The last time we had to replace the bezel and also pay for installation ourselves. We decided if this happened again, we would get rid of it. Well, it will be sooner than later as the oven glass has cracked. Needless to say, we are not return customers.

My Dacor Preference 30 double wall oven (model PCD227R) was installed on 5-14-2004. On 12-31-2007, I replaced the upper oven high limit switch for cost $146.56. On 5-19-2010, I reset the lower oven high limit switch for cost $95.00. On 8-27-11, I replaced main control panel (Bezel Assembly), whose parts cost $271.10. On 12-14-2011, I replaced the main relay board for $214.02. On 1-16-2012, I replaced main relay board again, and it is under warranty. On 2-3-12, I replaced upper oven temperature sensor for $32.09. I am awaiting authorized Dacor service technician to calibrate both ovens.

Like many of you on this site, when we remodeled our kitchen in 2000, I researched and decided to shell out the extra money for the highly recommended and higher priced Dacor everything. We got a double oven, glass 30 cooktop and an exhaust fan. 12+ years later, I wish I had bought GE! My ovens have had so many problems I cant even count. Basically, the temperature doesnt hold correctly. I have used oven thermometers and my husbands fancy gauge to check temp. I had a whole transformer and control panel changed out in hopes that it would correct the problem, but it didnt. I think it has something to do with the self-cleaning. I think it gets so hot that it fries the controller. I never use the broiler so its not like I left the door open and wasnt supposed to. This afternoon I set the oven to preheat to 350. I set my little cakes inside that I was making with my grandson. About 5 minutes later, it smelled like something was burning so I checked the little cakes. They were already charring on top and then I noticed that the top element was fiery red, basically on broil! What the heck?! This is ridiculous! Im not going to spend another $500 for another repair! I am waiting to see what the repairman says.On another note, my stovetop cracked twice! The last time, Dacor was nice enough to sell one to me at cost and my husband was able to install it. It didnt match the old one and I was told by Dacor that they dont make them anymore and that is made by a third party supplier now. The old one had a textured finish and this one is just very shiny and scratches so easily! I hate it. We also had a retractable exhaust fan put in because the stovetop is in an island. Every time I turn it on, my basement smells like whatever is cooking. Now the buttons dont work anymore. That is unless I jab them so hard with a sharp object that it finally makes enough contact to work! This is another part that we got at cost that my husband had to crawl around and repair that still doesnt work.So, all three Dacor appliances we bought have turned out to be very disappointing purchases. Dacor should stand behind their products better, offer longer warranties or better yet, build better products! I would never recommend these products to anyone!

We are in the process of remodeling our house including an entire new kitchen that we cant wait to finish to invite people over and show. HOWEVER, the cook top already has a light burned and finally the cover of it ended up falling as I was wiping down the stove (very softly by the way because I like to treat my appliances really nice). We have had this stove for less than a year I havent even made the last payment and it is already with a light burned out. REALLY? My husband spent countless hours researching the best appliances and decided to get this one and to come to find out that it is not good it is a complete disappointment. I am sooo upset. DO NOT BUY THIS BRAND!!! Save yourself the hassle that we are now going to go through trying to get a hold of someone on the phone and see what they will do if anything. I bought it from AJ Madison.

We own 3 Dacor appliances, gas cooktop, microwave & built in oven. From the day of installation of wall oven there was a problem. Without going into detail suffice to say it was repaired 3 times within several months, under warranty. We were having issues with our microwave not working consistently, after several service visits, not under warranty, we now are told it will cost over $600 for the part. We are now looking for another brand of microwave instead of fixing the Dacor. On a side note the rings for our Dacor gas cooktop never come clean no matter how hard you try. The material used are definitely inferior. We have another property with all KitchenAid and have been happy with the performance. Our fridge & dishwasher are KitchenAid and I regret not getting the same brand for our other appliances. If I could give a minus star for Dacor I most certainly would do so.

Our 30in Dacor double ovens are approximately 12 years old. I feel they operate adequately. However, not better than our much lower end appliances we previously owned. My main complaint is the self cleaning function. My old ovens self cleaning worked much better! With our Dacor ovens one must take out the racks and clean them by hand. This is very difficult and time consuming. I used the 3 hr option to clean my oven that was moderately dirty, mainly from cooking a prime rib over the holidays. After the 3 hr cleaning the oven was still very dirty with splatters and grease. Im now cleaning my oven again with a second 3 hr cleaning cycle. I know at the end of this second cycle I will need to do a lot more cleaning by hand! I hope Dacor has improved their inadequate self cleaning feature. If it hasnt been improved, I really cant recommend Dacor ovens.

Add me to the Dacor hate list. The $4300 oven installed in 2000 is now a whopping $6400. My motherboard #2 is broken and the glass on the door cracked which to me is a safety issue. This is a two adult, no kid household so figure. We use the oven about 7 times a year. My Dacor rangetop and hydraulic exhaust have both required service as well.

I purchased my Dacor Epicure Range 8 years ago when I remodeled my kitchen. My other appliances were made by GE and Bosch. Ive had to service my GE appliances a couple of times in the last 8 years, but it is the Dacor that has given me the most grief and it was the most expensive appliance purchased. It has never been reliable with regard to convection baking. Initially I thought it was my inexperience with a convection oven. I read everything I could get my hands on and kept trying...after talking with a friend who does quite a bit of baking I realized its not me, its my oven. Then the real problems started. First it was the broiler/ignitor, next it was the membrane in the keypad. Two months later it was the relay board and this time it was the broiler/ignitor....Again! Started calling Dacor when the relay board went out because at this point I had spent $1,000 on repairs....after I had paid $4,000 for the range itself. For the last two repairs Dacor has paid for the parts, while I paid for the service call and labor. This has reduced the cost of my last two repairs by about 50%, which is very helpful. However, Im still very disappointed in the product. I spend a good deal of time in my kitchen and do quite a bit of baking, cooking, and canning. I thought that if I spent more money and bought a high-end appliance, it would serve me well. At the rate that Im going, I will need to purchase another range, unless I want to keep throwing money into repairs on this one, which I dont. I will not ever purchase (or recommend) another Dacor product again.

We have owned our dual-fuel Dacor stove for about four years. We purchased this stove because we needed a down-vent - this is how our kitchen was already configured. We had only the Dacor or Jenn-Air stoves as choices and went with the Dacor. I have been thoroughly pleased. Everything works consistently including the self-cleaning feature. Prior to this stove, we had a Thermador which was expensive and NEVER worked consistently. One feature or another was always on the brink. The Dacor is such a relief. And good looking, too.

We purchased a under counter Dacor oven. The timer started given problems, tried contacting Dacor. The rude customer service advisor first talked to me like a police interrogation, then said sorry cant help. A joke of company with cheaply designed products. Never again.

As a contractor, we were fortunate enough to build our dream home which was completed in 2005. After much research and many show room visits, we purchased Dacor appliances for our kitchen. As the saying goes, if I knew then what I know now. Our biggest (note I said biggest, not only) issue is with our ESC130 oven. If you own this oven, do not, repeat, do not, use the self-cleaning mechanism. I have had this repaired once and then replaced once (along with a relay board). I seldom use this because I know when I do the lock mechanism will continue to cycle until it is replaced. This means, while I can still use my oven, I have to time when I open the door based on when the lock is cycling in the unlock position. I must also turn the oven off at the circuit breaker or listen to the continuous warning beep that the lock is cycling (as if I didnt know).After repairing this feature once, I next choose to have the mechanism replaced and Dacor offered me a discount on the parts (the oven was and still is out of warranty) at a cost of more than $500.00. This is on top of what I had already paid to have it repaired just 18 months earlier. I feared using this feature again as I didnt want a repeat performance. After cooking macaroni and cheese yesterday, I felt I really needed to clean the oven and made the mistake of using the self-cleaning feature of the oven. I dont know why I was surprised when the locking mechanism refused to stop cycling.I contacted Dacor today only to speak with the rudest customer service representative I have ever encountered, Steven. No last name. He is the only Steven who works there. He refused to listen to me, spoke over me when I did try to talk, and did not allow me to speak with anyone else. There are no supervisors available on Fridays and he could not transfer me anywhere. I left a message for someone else to call me (they did not). I called back later that afternoon and was given the name of a supervisor, Nhi. She was not available and I spoke with another customer service representative. I learned that Dacor is aware they have a problem with this locking mechanism and are trying to correct it. This got my hopes up, thinking that the company would now do the right thing and replace this mechanism at not cost to me, or at least at no cost for the parts. Not so. Even though Dacor knows there is an issue with this mechanism and they are supposedly trying to correct it, all they can offer me is a discount on parts. Really? Wow! A discount for a part that you know doesnt work properly and probably wont work properly because they are still working on the problem? I just really dont know what to say. Is this supposed to make me happy as a customer? Would prospective customers want to buy a Dacor product knowing that Dacor is more than happy to sell me a known defective product at a discounted price and they should expect the same? It is probably needless to say that I would urge all prospective Dacor owners to not waste their money on any Dacor product as they do not care about their customers. I will certainly be doing my part to warn others and hope this serves to warn others as well. Dacor has a lot to learn in terms of building even what could be called a good product and standing behind what they sell as well as becoming a customer service oriented company.

We purchased this oven February 2009. On 6/7/11, we had to replace the touch pad assembly. On 12/16/13, we again had to replace the touch pad assembly with a cost of repair to this point of over $900.00. The over cost $2,395.00 when purchased. On 3/16/14, while on convection/bake the oven switched over to broil. On 3/20/14, a repairman came to the house. The condition did not replicate but the repairman, in conversation with Dacor, determined that the fix, if this should happen again, would require the replacement of the relay board and ERC control at a cost of $700.00. On 3/27/14, while on convection/bake, the oven switched over to broil. I called Dacor and was forced to leave a message.

We got a Dacor oven and microwave wall mounted Unit 7 model DMT 2420S when we remodeled our kitchen. I have had problems with the microwave with sparking on and off. I have stopped using it as I am worried about a fire.

As I have read in most of the reviews, we have also experienced the control panel on our 30 inch dual range cracking over the years. We were told not to replace it because it would continue to happen. Ok, lived with that... Now something new has started to happen, the plastic handle on the oven door and surrounding area has started to melt. It got so bad after a self clean that it is collapsing. Now there isn’t much of a seal at all when the door closes. The stove isn’t brand new, but this has to be a fire hazard, and consequently, now the oven will not even turn on. I’ve reached out to Dacor with no response yet. I’m done with this company!

Weve had these appliances for 15 years. The cooktop has worked well. However, it could be improved with a lower lever for heating on its small burners, allowing it to simmer water rather than boil. The Dacor exhaust we purchased is one of those type that pop up out of the counter. It works but leaves much to be desired. When it runs, it pulls so much air the flame goes out on the burners. It is still not efficient at getting rid of cooking smells or smoke either, but that is simply a problem with all of this design so I cant fault Dacor. We have the biggest problem with the double oven. There are three main issues: 1) Whenever we run the self cleaning function, it pops the heat safety switch inside the oven housing so I need to take it apart to fix it. Hence we work to keep it clean so we never use the cleaning cycle. 2) The oven door gaskets prevent to door from closing and sealing all the way. The door tilts out app. ¾ because of this. We were told by the service guy who came to fix problem 1 above that this is the way the doors are(!). Our bottom one also tilts out but not as much. Ive dealt with this for 14 years! 3) We have to sand the burner electrodes on the cooktop to ensure they spark to light the burners at least 2-4 times per year. Not sure if that is normal or not.

Purchased a Dacor freezer. Freezer does not come with outer panel. Understandably, because you can choose to put your own custom panel on or order one from Dacor. Found out Dacor was bought by Samsung, a few years ago. So I decided to order a Stainless steel door from Dacor. One of Dacors reps suggested I order from J@J international. I placed order and two days later they called back saying they cannot ship door to me UPS nor FedEx will ship it. They refunded my money, so I reordered from someone else. Got ss panel toe kick and handle. Opened box only to find out no hardware, brackets ss trim for sides screws and so forth. I assumed mounting hardware would be with door. So began the part search for parts. Come to find out Samsung changed Dacors part #s. Vendors who sell the parts could not come up with parts or told me not available. Reliable parts agent told me this. I was told they should have come with freezer. Meanwhile called back Dacor to someone who specializes in dealing with these issues. She took over 45 minutes of my time giving me the impression she was gonna resolve the issue. She finally said we have the parts and inferred that I must have not talked to reliable parts. I assured her I did. She continued to refute what I told her. I have been right at two months trying to get freezer door installed. I called an Appliance dealer in Salisbury Md. to get assistance. He told me when Samsung bought Dacor he dropped line. I now see why. It has been the worst experience I have had with a company that has absolutely done nothing but appear to be concerned and say they are sorry but do nothing. It looks like it will be another 750.00 to get a couple little trims and brackets and a few screws. If I had it to do over I would never have gone down this road. This has been a two month old nightmare that is still going on. Best advice I can give is steer clear of Dacor/Samsung. Was going to buy matching column refrigerator. Not now.

We have a new (one year old) home with Dacor appliances. The microwave oven went on the blink the first month but was repaired by a factory approved repairman. Something to do with the computer. Now the double oven will not hold a temperature. We set the oven at 420 and it only goes to 360 even though the readout shows 420. We just decided to skip the repair process and bought a new Wolf oven. This is our second Dacor within the past two years and both have had the same problem. Dont waste your money.

I am amazed by the sleek look and design of the new Modernist refrigeration Dacor has to offer. The built in column pairing is my favorite with all stainless steel interior, tempered glass, and LED lighting that WOWs anyone who opens the door. The water dispenser is flush against the interior wall of the refrigerator and the freezer can offer two ice makers, one for regular ice and one for your high end cocktail drinks. These units are PURE LUXURY and HIGHLY RECOMMENDED!

Replacement light for the oven - I could not find anyone that carries the halogen bulbs for my oven and called Dacor parts line. The bulbs come in a package of two. They were $79.95. I was told I should have called two months ago, that they were $29.95. So would I buy another Dacor Appliance? I think not.

I bought a Dacor Epicure 48 range in 2003. It has never worked correctly. I read many other complaints on this same range. I had the burners replaced and I still have to light them with a match each time I turn them on. The oven temperatures were never correct. Nothing bakes properly even following their directions. It bakes very uneven. The hinges are sprung/broken (as the doors are too heavy for the lightweight hinge they use). I have had numerous service calls over the years and still not a good oven or repair. I too am very disappointed in the fact that this product is a lemon and they will not replace it.

Updated on 02/23/2021: Its been several weeks since I first posted. The only reply that Ive received was an email via this site that requested information from me on my claims. The info was provided the same day. A week has gone by since I provide the information and I have yet to hear back from Dacor. Not even a were looking into your issue. What I did receive was a notice from Samsung (who has acquired Dacor) telling me that one of my service tickets has been cancelled. I dutifully called the listed number to get more information... only to be told that the Samsung customer service rep could not help me and that I needed to call Dacor. Ive tried to approach this matter with humor up to this point but I am out of patience. Given the price I paid for these products, I expected a premium customer experience... the experience I have received has been abysmal.Original Review: I did not think that a customer experience could be this AWFUL or that a vendor could seem to care less than Dacor cares about resolving my issues. After 5 months, the exhaust downdraft that we purchased still does not work and Dacor either does not respond or - when I can get someone on the phone - I get any number of standard excuses (parts shortages, Covid, port backlogs are delaying deliveries, the integration with Samsung, etc, etc). I am also missing basic parts such as shelves(!) that should have been installed during the original installation. The retail partner (Specialty Appliance) does not seem to have anymore luck in getting answers.

My Dacor Double oven is less than 5 years old. Lately, the broil function has stopped working well on both ovens. I contacted the ONLY authorized Dacor repair center - Home Appliance Repair GTA (HARGTA) and told them my broiler wasnt working well. Their repair technician came to my house, took both double oven doors off in order to give me the assessment – that my upper broil function was not working well. In fact, both upper and lower do not work well but thats a side issue. In the process, the technician broke or did not properly reinstall my double oven door. I called and he returned and again, removed BOTH oven doors. Now, my upper door is working well but my lower door has no hinge and falls hard and heavy. This is extremely dangerous. I have left multiple messages with HARGTA and they are not getting back to me. Ive even contacted DACOR which is only in the US and they havent gotten back to me either. I purchased a Dacor oven to get a quality appliance and excellent after care service. It appears that both the appliance and the aftercare service do not live up to their reputations. P.S. The quote to repair 1 broiler is $750 after less than 5 years of use. That will equal 1/4 of the oven cost in less than 5 years.

Purchased Dacor Induction Range w Convection Oven RR30NIS-C in October 2013 and LOVE this range. Accidentally broke the glass on the induction cooktop with falling object mid-March 2020. Only the glass is broken, and all other electronics, induction burners, oven, etc are functioning fine. Called Dacor support to acquire part number for a glass top for repair - obtained part number #701751 superseded by #702285, BUT was informed that the part had been discontinued and is no longer being manufactured or kept in stock. No other advice was given other than to discard the entire $6000 range. Multiple phone calls with service.I asked for a listing of third party part distributors and was referred to four distributors on the Dacor public website and given no other info. I called all web-based third-party distributors I could find in USA and Canada to see if anyone had the part in stock, with no luck. I contacted two technicians to see if they would be able to obtain the part through their channels, with no luck. I am an engineer, so I spent some time pouring over technical manuals trying to find a solution to replace the entire induction range cooktop assembly (top part of the range) with a later model, and although its possible, Dacor would not provide the ability to purchase an RNR30NI range cooktop assembly that could be fit into the existing housing on top of the range. The convection oven is completely fine, and I cannot believe that Dacor has given me no other option but to pitch a six-year-old $6000 range because they stopped manufacturing one fragile part made of glass. I would imagine that many consumers may be in the same position as I, as these cooktops are breakable, and accidents happen. I have reached out to Dacor support desk numerous times without resolution, and I am at my wits end with a $6000 boat anchor in my kitchen. What a waste of money! Poorly done Dacor!I would like Dacor to provide me with some sort of solution whether it be the part required to fix my induction cooktop, or a replacement Induction Range with convection oven, or reimbursement of the purchase price so I can obtain a replacement on my own. If I am not able to find a solution to repair my range, I will never buy from Dacor again! Dacor will discontinue easily broken parts without warning! You may spend thousands of dollars and not be able to repair your appliance after warranty expires!

In September 2009 we did a complete remodel of our kitchen. Replaced everything but the refrigerator, with DACOR appliances. Within a few months we had problems with the dishwasher and finally replaced it with a GE in 2012. About that same time we had problems with the Dacor Epicure 30 Single Oven Model EO130SCH control panel and had to have the repairman out to work on the relay/computer board. At Christmas 2015 I had trouble baking, the temperature wasnt accurate and have had the repairman again. He says that the computer board is fried (his term). Ive tried calling Customer Service with no success. Ive e-mailed them with same results. The appliance repairman has told me that he cant find the part. All the distributors that hes called have been told that the part is on back order. Ive been without an oven for over two months now with no fix in sight. Have been told that IF we find the part it will probably run around $500.00. These are appliances that are only six years old and have had gentle use by senior citizens. Anyone reading this - PLEASE DONT BUY DACOR! Youll be sorry as I am.

We were incredibly disappointed, not only with the range but with the customer service from Dacor. We purchased this range in January 2016 and here we are in July with what is basically a pan holder sitting uselessly in our kitchen. Problems started immediately. The first time I used the oven, it locked with the cooking food inside. It turned out that the thermostats on both ovens were so out of whack that the oven temperature reached self-cleaning mode levels so the ovens locked with the food inside! We had both thermostats replaced twice and still had the same problem. Eventually, the thermostats were calibrated, but still within a range. In addition, the switch for the convection oven just stopped working. After 6 months of trying to deal with this problem, we will be returning the range and replacing it with a different brand. At no point did Dacor offer to exchange the range, they simply kept sending a repair person.

Updated on 11/29/2018: Further to my recent review of my Dacor wall oven, I went to a high-end appliance store yesterday to research replacements for my microwave, oven, warming drawer installation (so, yay, I get to spend $13,000-plus to replace items I have had for only eight years). I cannot verify the accuracy of this, but the salesman explained the problem. For a period of time, Dacor and Viking used the same third-party supplier for their relay boards. Unbeknownst to the companies, the supplier substituted a part that was later discovered to be defective. Unfortunately, all replacement relay boards contain this part, so the problem will recur repeatedly, as many on this site have discovered.As bad as the cost of periodically replacing the board is, the unreliability of the oven is worse. As happened last time, mine works OK sometimes, burns everything other times, and struggles to get to the desired temperature other times. And because the behaviour is unpredictable, it cannot be reliably recreated when a repairman visits. I have had one email from Dacor and I responded with the information requested, then nothing. I suspect that they know they cannot fix the issue in a permanent way, so theyre just hoping all of us with this defective part will just go away. It looks like newer models that look like mine are still available, but I refuse to pay $5,000 on the off-chance that it has a better relay board. I am looking at Miele replacements.Original Review: I have had two Dacor wall oven, microwave, warming drawer installations. The first one was only a couple of years old when we moved, and Id had to replace the microwave, but I put it down to a power surge in the house after an outage. I have now had the same set in my new house since 2010. I have had to replace the microwave again, but not because of a power surge. It just stopped working. The oven has been a complete nightmare. The probe broke and although I had it repaired, it never worked properly, but the worse problem is that I am about to have to replace the electronic board for the SECOND TIME. When the problem occurs, the oven heats up to the setting but the element just stays on. I all but ruined an expensive cut of meat on the weekend – with company coming, no less – and just had to throw out a batch of muffins. I am considering tearing out the whole installation and getting another brand that doesnt destroy my food. It would probably be cheaper than having to fix the oven every year or two and replace the microwave periodically. These appliances are garbage.

I have a Dacor cooktop, single wall oven, warming drawer, and dishwasher that I installed in my kitchen in 1992. That is 20 years ago. I have never had a problem or needed a repair on any of the appliances. They have worked perfectly. I hate reading about all the problems people are having with their Dacor appliances as I am about to do a major kitchen remodel and plan to go with Dacor again.

Lemon appliances. The dishwasher breaks every 6 month. The gas range top breaks every 6 month. The Microwave breaks every 6 month. Awful products!!!

October 2013 we had the Dacor model# EORD230SCH installed. It broke just in time for Thanksgiving! After several attempts of repairs, Dacor replaced this oven model# EORD230SCH with the next newer model at no cost. Not more than one month later the replacement oven doesnt work. Service is painfully slow. We had a 03 year warranty on the original purchase and the clock keeps ticking from the date of the initial installation. WE have asked for and been denied by Dacor, to reinstate the 03 year warranty once the unit is actually working. We bought this unit, spent extra money, thinking we were buying quality. So, two ovens in less than one year, doesnt equate to a quality product to me. Keep getting the standard answer about the warranty - no added time will be assigned.

I bought a Dacor appliance package for a new custom home which costs over $30K+. Every single piece of appliance is defective. I am OK as long as Dacor can fix or address the issues but it takes them several visits, put the appliance out of order and fixing it does not happen any earlier than 8-10 Weeks. Imagine you living with a fridge, microwave, range and oven for 10+ weeks. The column freezer stops making ice. I call for service and tech informs the lever was jam and he fixed it. Wait 48 hours.After 48 hours still no ice. Another call and after a wait of 3 weeks another visit and diagnose need new part. Wait for part 4+ weeks and another 3+ weeks for replacement. Fridge does not cool and maintains temp 45 degree+. Service tech showed up 3 times and promised it is fixed. Have thrown out thousands of dollars worth food. To date I dont have it fixed. Waiting for a part, tech not available scheduling issues etc. To date I have been out of fridge (8/12/2021) 9 weeks from I made the first call. Currently I have a tech scheduled for 9/1/21.This is not the end. Microwave will run normally and wont heat the food. After several phone call and waiting they figured the door pin was not connecting properly and need parts to fix. After 10+ MONTHS it looks like it is fixed. The range control panel is hanging from underneath and no one seems to care to fix it. Every time I call they tell me its normal. I believe Dacor has not QA/QC in place prior to shipping the appliances to customer. Worst experience ever. If you need more details do not hesitate to call me on **. I hope you run away from Dacor. Dont even consider this option. I have a track of all phone call and email and timeline with Dacor service. I am planning to file a lawsuit and recoup some of the costs and losses.

We did a total kitchen remodel and purchased Dacor appliances. Big mistake. Had to spend 500 on refrigerator repair (model EF36BNDFSS). Oven is off 25 degrees on temperature. The glass top for burners was defective. Would never purchase Dacor. Microwave front trim keeps coming off as well.

Dacor Distinctive Series Range model DR30D - One week after the appliance warranty expired, the oven stopped heating. The repair man replaced the circuit board. We still got a code 33 when we try to get the oven to heat to 400 degrees. Called customer service, they said to flip the breaker to the unit off for a few minutes. Seemed to help but we do not use the oven much, as we also have a Meile microwave/oven that we love and use that more. Then I cleaned the oven using only the ovens program. That locked down all of the gas cook top knobs. I called the repair service, it snowed on the Saturday of the appointment. They cancelled. I did not check the stove on Sunday. On Monday the repair service walks in and simply turns it on, no problem. VERY FISHY!!! I have heard the manufacture can control it by computer chips. This appears to be very true. Now the stove does not heat past 250 degrees. After speaking to a few people it appears this is a very common issues. Dacor is a lemon. Do not waste your time and money.

Thank you for your attention. Since my post, a resolution has been reached and Dacor will be replacing my range with a new one. That is much more representative of the pride and reputation of Dacor. The executives were very responsive. Perhaps front line agents are not empowered to make these decisions, however, in my case, the escalation brought the matter into the right hands. Happy with the direction towards the final outcome, not the 4-month process that discounted the reputation and my perception.

I spent a lot of money buying a Dacor double wall oven because it was supposed to be top of the line and dependable. Now, the circuit board needs to be replaced and the oven is just 5 years old! This seems absolutely ridiculous for an oven this young to have such a major problem! I am very upset about all the money I am going to have to spend to fix it. Ive never, ever had any oven problems with other brands like this in my life. We remodeled our kitchen and I thought I was getting something better and now I realize that this brand is not living up to my expectations at all! I am using an authorized Dacor repair company and they told me that they are seeing lots of problems with this brand. I do not recommend this oven to anyone.

Stylish products with amazing performance. Originally, I wasnt very familiar with Dacors luxury appliances. However, I saw some of their new products and decided to take plunge. Glad I did! I bought a 36 French Door refrigerator for the house and I love the features and performance of this fridge. The fresh zone adjustable drawer can go colder than the standard refrigerator compartment, so I keep it at just below freezing for my beer and champagne. Makes ice super quickly and I feel that the produce also lasts longer. Overall, very happy with this purchase and when I do a full kitchen remodel, I will be considering their cooking products as well.

We did a complete kitchen remodel 2 years ago. My husband talked me into purchasing american made over the Bosch products that I preferred. This has been a horrible experience. The dishwasher does not clean. I was told to prime the water and purchase the higher end platinum packs. That did not work, then it was add lemi shine. That has not worked. The water never completely drains, ugh old water. A service tech could not tell me where the rinse aid indicator light was and insisted mine did not come with one! Microwave does not heat in an adequate time. All listed times I have to double time if not more. I was told to put a Rubbermaid container over the food product to insulate the waves... ha! Oven does not regulate heat. when I go to increase the heat during stated recipe, the screen always say 50 even though I would have it at 375. I was told it always will revert back to 350, really. I had all Kenmore appliances prior to the Dacor and never had a problem... Do not buy, I wish I hadnt. We are filing this with BBB and headed to small claims court.. This should be fun. I hope Dacor sees this.

We had problems with it all the time. The front plastic cracked and ended up causing the oven not to work. We have spent (over the past 9 years) about $1,000 on repairs. Now, we just had it fixed and our new clock that was installed into the oven is running fast. After just being fixed, it takes 20 minutes to heat up to 400. Honestly, it always has been that way. We’re not happy with it at all. We bought a Sears brand oven for our church, and it works great, and the cost was only a third of what we paid for the Dacor oven. The Sears brand bakes just as good as the Dacor (when it works). I think it was a waste of money to buy this Dacor oven.

Dacor EO227SCH - double wall oven. Installed all Dacor appliances when we did a kitchen renovation in 2008. Stove top, Micro Wave and Warming Drawer each have been excellent. Ovens have been a nightmare. Dacor would not honor warranty 7 days after it expired. Had no less than a dozen service calls in first 3 years. Ovens conveniently have problems around holidays. Example: lower oven quit working two days before this Thanksgiving - last week! Paid a high price to get Dacor and have paid thousands and spent countless hours on service calls since. Am totally dissatisfied with Dacor products and the companys refusal to stand behind its product. I tell everyone who is contemplating Dacor not to. Did it today with a couple who signed a contract for a $1M home in N Atlanta. Builder specified Dacor and I strongly advised against it. Homebuilder is now looking at other options.

We purchased a DACOR double wall oven (MOH2275) in April 2012. We are waiting for service to arrive for the fourth time since we purchased the oven. I find this unacceptable. We have had 2 other ovens in the last 30 years and they did not need any service. In general I have found appliances to be of such reliability that I dont get extended warranties. DACOR gave a 3 year warranty on this oven and now I know why. Hopefully this service will fix it for a long period of time.On the positive side, the oven really works well. It is so well insulated that we feel very little heat coming off it. One serious flaw its overall operation is the reheating of the oven. If I bake something at 350 degrees and then want to reset the over to 450 degrees, the oven does not go into preheat mode and does not let you know when you reach the required temperature. I am hopeful this will last awhile and not have to be replaced for what we paid for it.

Replaced main board on top of oven because of oven light turning itself off and on endlessly. Cost was near 400 dollars with service call. Now, 2 years later, F1 beeping nonstop, and we have to turn power off to stop it. Last night, the beeping started at 3 am! I would never buy another Dacor oven. The Dacor microwave has never been able to pop popcorn. Now the carousel is failing to rotate. The only thing positive about Dacor is the styling.

After 4 months our microwave exploded when we tried to bake 2 potatoes. Dacor has reviewed the situation and acknowledged the product was defective. 10 weeks later they keep saying the replacement is on the way but no one knows where it is. Dont buy dacor products.

We purchased a Dacor wall oven when we renovated our kitchen in 2010. After five service calls, a replaced circuit board and broiler element, they found a broken wire which must have happened during clean cycle. I have been without an oven for two months and would not recommend buying a Dacor oven because I think it has a faulty design. The issue is still ongoing.

We purchased a Dacor 30 Heritage Gas range and installed it in early Oct 2020. Within a day a gas leak from the back of the range was identified by our gas contractor. Dacor repaired it quickly (12 hours). I was impressed (though concerned it already had an issue). In December 2020 I noticed that the oven indicator light was not coming on. I contacted customer service and despite indicating that there was a problem, was simply told what the light was for. Then, in February 2021 (under 5 months after installation) the oven stopped working. The service technician indicated it was an electrical issue and the gas would not ignite. It has now been over two weeks and we still do not have it repaired nor any indication of when it will be repaired. We spent $5200 on this range. I do not recommend Dacor.

We purchased a home with brand new Dacor appliances. Within 1 year, the relay board had to be replaced. One year later, the relay board has to be replaced again. Its $600 each time for parts and labor... The part alone costs $500. The company does not warranty the relay board. At this point, we should have purchased a new wall oven. They claim these are superior appliances. Our gas stove top works well, but the wall oven and refrigerator have been nothing but problematic. We will never purchase this brand again.

I moved into a house that already had a Dacor unit in place. Within months, I discovered that I owned an oven that could be fixed by throwing the circuit breaker. Then, I learned about invisible hands that turned the 325 degree convection oven to a 500 degree broiler. The final act was having all three glass panes shatter and the control panel cracking as punishment for assuming that the oven cleaner on an expensive gourmet stove would function according to manufacturing standards. The repairman ordered replacement parts. He spoke with someone who was off shore so forget about Dacor being all American made. The wrong parts were sent. He has reordered. Meanwhile, I have been without an oven for two months. If this goes on, I am going to Home Depot and buying a Hotpoint or GE. It is the same price as replacement glass panels and the control panel.

I purchased a Dacor Double Oven 5 years ago. It is a beautiful design, but unfortunately a piece of junk. Over the 5 years I have had the oven, I have had service technicians repair the oven on 7 different occasions. Unfortunately, my oven is not out of warranty and has failed once again. Today was my 8th attempt at service and the service technician could not get the oven working. I have called Dacor, pleading with them to stand behind their product and to replace this useless piece of equipment. I continue to get L22 error codes, and the main circuit board had been replaced twice. After persistently calling Dacor’s customer service, they finally said they would sell me a new oven at a discounted price to the tune of $4800 plus tax, shipping and installation. I ask myself, why would I want to buy another piece of junk? If Dacor wont stand behind their products, perhaps someone should initiate a class action suit against them.

We were out of state from December 21, 2014 to January 2, 2015. The condition of the refrigerator was discovered at about 9:30 PM on Saturday, January 2nd. Upon opening the door the Dairy Compartment Cover fell to the floor. We could immediately see the damage but did not know the source. As a result, the unit was turned off. The owners manual was consulted along with a review of the Dacor website. The office was closed on the weekend so Monday was the earliest we could obtain names of Dacor authorized repair agents in the Phoenix area. A authorized Dacor repair technician stated the light switch or light circuit in the board failed. The interior light bulbs located at the top of the refrigeration side of the unit remained on when the refrigerator door was closed. The heat generated by the continuously lit bulbs led to the melting and charring of the plastic light fixture. The light socket melted, the wiring harness melted into the socket assembly, light switch, and control panel. The heat was intense enough to warp the Dairy Compartment clear plastic cover, some of the adjustable door bins, and the interior door liners. Also, all food containers made from plastic such as salad dressing bottles, mustard, ketchup and mayonnaise, etc. were disfigured. Of course all the contents from both the refrigerator and freezer had to be disposed.Before leaving on an extended trip we had been following the instructions preparing for a vacation listed on page 19 of the owners manual. On our departure date the food that would not have lasted more than two weeks was removed from the refrigerator. The ice bin was emptied and the wire shut off arm was raised to the OFF (O) position. Note, page 19 does not mention to set the Sabbath mode when leaving for a short or long vacation. We were fortunate that the damage was contained within the refrigerator.

We built a new home in 2004. All appliances were Dacor. Since then, the oven has had to be repaired 4 times; the microwave had to be replaced; the cooktop has had two repairs and now will not light automatically; and the patio barbeque completely burned up and some of the parts melted. I did report that to the company and to the US Product Safety Commission. We have not abused any of these appliances and have followed the manufacturer recommendations all of the time. Dacor charges top dollar for their appliances, but they are not as good as cheaper brands. If you try to contact Dacor, they have a well-so-what attitude.

We purchased this unit 7 years ago, just a family of two with visiting grandchildren. Unit came, had a crooked door and a bent latch, which we had serviced and supposedly corrected. When self cleaning the latch still made grinding noises. Over a year ago the oven stopped working period. A December service call said needs a new latch, sensor and display -we are now in 4 figures($). Oven operates for month and a half. January 2019 Service call now new door latch, relay board and main wire harness 4 figures again double! Oven stops working yesterday (June). Service call today new latch, motherboard and something else and another 4 figure repair cost. Same repair parts same problem! Patience is a virtue, but repair costs are sinful! Next step, Boat Anchor! Problem from the beginning and still a problem now.

Wish Id known Dacor issues when buying my oven. (Primarily for style - yes, assumed it would function as stated; high end brand). Thank goodness I DID NOT BUY other Dacor appliances. My 30-inch Dacor oven/cooktop burners work but finish started coming off quickly. Above range microwave handle broke within a year. MAIN PROBLEM: OVEN DOOR either wasnt properly installed because it doesnt close flush with unit or its hinges have loosened over the years. Although oven eventually heats, it takes forever. After examining door hinges closely, looks like oven has become unhinged - as have I. No loose parts seen. Recommendations? Other than STEER CLEAR OF DACOR.

We purchased a home with a 5 year old Dacor Discovery IQ Double Wall Oven. Model Number DYO230S. Great looking and it has a very sophisticated and functionally rich digital control system. Problem is the digital control system does not work. The stove has a mind of its own and will just shut off for 24 to 48 hours and return to function randomly. Shutting the power off and turning it back on has no effect. Dacor (Now Samsung) has been completely un-helpful. Bottom line response - tough. Product is no longer produced, replacement parts no longer in stock - maybe there is a part on eBay ** Honest that is the answer. I have called parts companies who also complain about Dacor (now Samsung). No luck. So we will now need to purchase a replacement product for anywhere from 4,000 to 10,000 dollars. To replace a 5 year old - 8,000 product. It will definitely not be a Dacor or Samsung product. And I will do my best to put similar reviews on the internet where ever I can.Just to add some balance - 21 years ago we custom built a home and purchased two Dacor ovens. Both were great. 21 years of flawless operation. When we saw this oven as we went through the home purchase process we were delighted. What a disappointment. Also - before the oven started to go wacky on us we needed to replace the bulbs (2) in the oven light fixture. Initially I contacted Dacor parts and had a very pleasant experience ordering the two replacements. However nothing came to our home. Called again and found that Dacor had been sold to Samsung and the price of the bulbs had doubled or more. No exaggeration. Stay away from Dacor and Samsung.

When the beverage center was initially installed 5 or so years ago, I went to put wine bottles in the wine drawers and surprisingly, the shelves are too shallow to properly hold some of the bottles especially tall Riesling bottles. I contacted Dacor to get some response to the poor design and got no response. Now the unit wont chill and I have just paid a repairman $162 to tell me it is not repairable because the unit has a leak in the refrigeration system and it is within a foamed in area of the system. So after only 5 years, I am replacing my wine fridge, not what I would have expected from a brand that touts itself as being high end. I am very dissatisfied with Dacor and certainly will not be purchasing anything of that brand again.

We bought a 36 inch Dacor range with oven last year, around September, when we moved in to our new house. We tried to turn the oven on Thanksgiving day for 10 people, but it would not work. We called for service, and they replaced the circuit board. The repairman turned the oven on, and it worked fine. We never used the oven, just the burners on top, because we have a second smaller oven, we like to use for every day cooking. Then came Christmas day, and we were having 30 people over, so we went to turn on the Dacor oven, but to our horror, it did not work again. We have owned this oven for a little over a year, and have tried to use it only twice. In that time, both on holidays, with a lot of people to feed. This time, when I called for service, they told me I will be charged $198, because when they tried to get Dacor to drop that charge, they said no. We are very disappointed in Dacor for not caring more about the customer.

Dacor double oven range turns off by itself while baking - Disappointed in Dacor, especially today. Thanksgiving 2016: baking turkey. Sill baking turkey. I dont know when the oven decided to switch off this time, but I have an uncooked turkey and guests waiting. The oven has done this before, but because it was new I thought it was user error. Nope, the damn oven mysteriously turns off on its own. Incredibly irritated with Dacor. The range hood we also purchased is a joke. We remodeled our kitchen 1 year ago and wanted quality appliances. Bad move. Save your money, folks. Save your money.UPDATED ON 03/10/2017: Dacor sent a company out to fix the broken new oven. Oven still cannot hold its temperature (It takes FOREVER to heat then loses its heat while still showing a high temp). This time I have a recording on what happens when the oven automatically switches off. Disappointing when we spent nearly $10,000 in Dacor appliances for a kitchen remodel. DACOR, please have a rep contact me!!! Still waiting to hear back!!!

I am thrilled with this stove. I have always had a vertical double oven so this is a first for me. Really pretty in my kitchen. Almost like a piece of furniture. Can’t wait to start cooking!!

We did a complete kitchen remodel in 2007. I wanted top of the line appliances, and I liked the look of Dacor. I spent over $10,000 on a refrigerator, oversize dishwasher, microwave oven and a warming oven... (I know). Within 16 months, everything started to fall apart. Of course it was over the one year’s mark so there was no replacing of the units on the manufacturers part. I have since replaced the motherboard on the dishwasher twice... total of 3K in repairs! I cant replace the dishwasher because it was oversized and we built our cabinets around it and no other company sell an oversized dishwasher. I have replaced the microwave oven with another one that looks just like it because for some reason it fried. The refrigerator constantly rattles and my husband and I are at our wits end because of it. The only thing that hasnt fell apart yet is the warming oven. Probably because we dont use it. I wouldnt recommend it to anyone. Its a total waste of money. Next time Im buying Kenmore. My old Kenmore is sitting out in the garage being a good and faithful second fridge.

We have enjoyed our Dacor oven for a number of years but cannot recommend this brand due to high cost and frequency of repairs. The relay board, at $400 a pop parts cost only, has had to be replaced twice within 5 years. The oven door hinges failed in normal use so that the door would not close tightly and had to be replaced. The halogen oven lights fail frequently requiring replacement. Parts cost is only part of the issue. The inconvenience of not being able to use the oven for extended periods of time and high appliance repair labor costs are significant. All in all, a very good oven but reliability and frequency of expensive repairs lead us to not recommend Dacor ovens.

The first F1 Error needed a new membrane repair for $470.00, after 4 years of service. Now, the same F1 error after the new membrane is only 13 and 1/2 months in service and it is now out of warranty. Customer service people are rude and unhelpful but when pressed, they said they might be willing to help after a service tech, which I have to pay for, diagnoses the problem.Even the Sears store people advise their customers not to buy Dacor products and that is sad because it is one of only 2 American made options. Dacor needs to step up their product engineering, commitment to quality and get rid of the rude phone people in Customer No Service. This is not the end of this experience but the only reason I am not junking the stove is because a comparable replacement is another 3000 bucks from another vendor which I cannot afford at this time.The irony of this is that the company clearly knows they have problems but when I asked if the replacement parts had been improved so the problems wont persist, I was told that no changes or modifications to the electronic brains had been made. How stupid is that! They are just asking for more problems with the parts they send you to fix what does not work.

We purchased a Dacor Epicure dual fuel range when we built our house 7 years ago. It was the most expensive appliance we bought and we wish we hadnt. We have had no problems with the stove top, but the oven, specifically the broiler unit has been a consistent problem. We rarely use the broiler and use the oven perhaps 2 or 3 times a month. Yet, the igniter had to be replaced in March of 2008 and again, in June of 2010. In January of 2011, the broil gas valve was changed and now in September, the broiler is again not working. I cant see pouring any more money into this appliance and will sell as soon as I find a buyer willing to take a chance on it. We have been greatly disappointed in this product.

We bought this oven and had it installed a month ago. Id love to love it, but unfortunately I dont even like it. Immediately after installation I noticed the touchpad for the bottom oven didnt work. I called Dacor and spent quite a bit of time while someone did the standard is the power on run through. I was told someone would have to call me back in the morning, at 9 am. The next day at 10 am having not heard a word, I called back. I was given the option to be called back (you wont lose your place, and our first rep...) Great! Nope. Four hours later still nothing. I called back again. Someone answered quickly and after a short call arranged for a service person to come out in a few days.Fast forward a few days and the serviceman arrives. Hes clearly never seen this kind of oven. He calls Dacor and talks to their troubleshooting department. They decide the motherboard is bad and reorder. Well, its been 10 days. *crickets*. There is no sense of urgency... In fact nobody even seems to care that my $7500.00 oven doesnt work and the microwave literally cant even pop popcorn. I would expect the company to rush delivery of the part. If need be replace the whole oven and figure out what is wrong with the motherboard on your own time. What I didnt expect is for literally everyone involved in the process of choosing and buying the appliance to not be able to find a solution. I give my new oven 1 star out of 10, because it looks nice. Id rather have an oven that doesnt have a smart feature and actually works. FAIL Dacor.

Dacor Double Oven Model D0230 - I have had my oven since November 2011. I purchased an extended warranty at the time of buying the oven. Right after it was installed, I called and said they needed to come and adjust the temperature control. It was off at least 50 degrees. It never held the correct temperature. Since July, we have had to replace 2 relay boards, two other parts that should take care of erratic temperature. Then I noticed the gasket was turning black in the corner and my glass pack in the window was steaming up and not clearing. The extended warranty would not cover the glass replacement and I was charged $126. They said it was cosmetic, but this was so bad that I couldnt see through half the glass. The steam stained the glass and you could not clean it, because it was inside two pieces of glass. Do not buy a Dacor oven. In 38 months I have so many repairs that I have lost track.

I purchase a home with a Dacor double oven. Unfortunately the oven begins transmitting multiple beeps and the touch panel will sometimes read off after beeping a while. I contacted the staff at Dacor requesting a service manual. They refused to send me a service manual and stated that only authorized technicians can service their equipment. Its obvious they used google or a local phone book and sent me contacts of appliance repair shops in my area.When I called, they had never heard of Dacor let alone be factory authorized. I called Appliance repair shops up to 50 miles away to find there were no Dacor Dealers. I found one 70 miles away but it was too far to send a technician. If I remove my oven from the wall and take it there they would attempt to look at it. I had to reverse engineer the thing to find that my touch panel has gone bad and now I cannot find a used one. I want to recommend that anyone considering an appliance DO NOT PURCHASE A DACOR! If you are looking for high end stick to SubZero / Wolf. Oddly enough I see that there hasnt been any reviews for the past 5 years. Maybe it appears people have stopped buying Dacor appliances.

I have had my 30 inch Dacor Dual Fuel Range since 2002. In the past month, the oven door seems to be falling apart. I had to replace the oven door handle after the handle cracked in the spots on the right hand side where the screws go in. When I tried to screw the new handle in, I noticed that the front panel on the door is lifting away from the door. It is more separated on the right hand side which leads me to believe that it is the reason that the handle cracked on that side. As a result, the handle cannot be properly installed. The only way this can be repaired is to call someone in to do it and it will either have to be glued together or the whole door would need replacing. Reading these forums, Im worried that my oven problems are just beginning and I dont want to start sinking money into this oven. I purchased a Dacor as I believed it was a high quality product and that it would be worth the money and last a long time. This type of problem should not be occurring. I do not consider 10 years a long time for a product like this. My sister has had her Jenn Air oven for almost 20 years and it has no signs of wearing out.

We remodeled our kitchen because my wife is a chef. So we thought a full suite of Dacor products was just what she needed. What a mistake! Our $6000 36-inch dual-fuel range had problems from the start. We had to replace the control panel, heating element, convection fan, and door seal. Finally, the liner split and the range became unrepairable. We made the mistake of purchasing a simpler, gas-only range because Dacor offered a modest discount. This $7000 range lasted four months before a failure in the wiring harness made it unrepairable!! We bought a Miele replacement. We have had performance issues with our Dacor warming drawer and microwave. DO NOT BUY ANYTHING DACOR!!!

I have owned a Dacor Convection microwave for a few years and is so far the best Ive ever owned. It works great every time, has great preset features and also has a great stainless steel look. Great Product.

Dacor Epicure Dual Fuel Range and Microwave - Where to begin? Perhaps at the end is best. Dacor appliances are shoddy, unreliable, outrageously expensive to repair and there is no customer support. That about covers it. We bought the above noted pair during our kitchen renovations 8 years ago. We thought that Dacor was a premium brand that would give us long trouble free service. How wrong we were! The only thing Premium about them is the price. 4 years ago, the microwave door refused to latch. Thanks to YouTube, I found out how to remove the door backing and found that the plastic part that comprised the latch was broken. Dacor was contacted - they no longer had the part. Try the open market I was told. I managed to jury rig a repair by using a wooden shim. 3 years ago, the range packed it in. Another repair - this time I was told it was the circuit board that had failed and which was replaced to the tune of $700 and I was cautioned that the second circuit board was not working very well - the interior light would not illuminate and the blue lights indicating a lit burner didnt work, and I should change it too. The smaller circuit board was costed out at $400. Last week, the door latch motor failed and the range began to beep incessantly. Now the oven cannot be used and repair costs quoted over the phone were in the 1000$ range. Thats it for us. Dacor is junk and belongs where its headed - the junkyard. Dont buy Dacor. Live and learn I guess.

We purchased a Dacor built-in refrigerator in 2011. After just 5 years the warning beeper came on. We learned that the main control panel - built by Whirlpool - was defective. We then learned that Dacor did not have any replacement part for this model. Our only alternative was the purchase a new refrigerator. Amazing!! Dacor reluctantly gave us a partial credit for a new (KitchenAid) model. However at the end of the day we are out of pocket over $2000 because Dacor built and sold a defective refrigerator with no ability to fix the problem. Very unsatisfactory handling of this situation.

Dacor came through! They sent me, at no charge,a replacement part. This new part is supposed to fix the issue of ice cycles in the freezer. Its a new drainage system that actually heats the water in the pan so it does not freeze up causing the water to back up. I am hopeful that this will permanently fix the issue! But props to Dacor for stepping up to the plate to fix this! Thanks, guys!

Im reading all these reviews and my story mirrors them all... I have actually contacted a lawyer and am considering either a lawsuit or going to small claims court because, at this point, its cheaper than continuing with repairs every other year. Has no one else considered a lawsuit under your states lemon law? Appliances are usually covered. I purchased the MORD230 wall oven in 2008... It was purchased as a second oven to my 6-burner Wolfe to cook a turkey or roast during the holidays. It has been used no more than 24 times... I have gone through 2 control panels and am now having glitches with the third. After doing a self clean recently the whole heating element blew - it will not heat at all. I am able to enter the temp but the oven just runs and runs and never heats. I have called Dacor furious for how many times this thing has broken in relation to how many its been used... They have offered parts at a reduced rate but I am not sinking another dollar in this oven on labor and parts only for it to break again. I asked for my money back and told them to come and get the piece of garbage they sold me. Do yourself a favor and buy a Wolfe... It works beautifully... My only problem was the cast iron grates rusted a bit recently... I called their customer service and was on the phone for no more than 5 minutes and they overnighted me a whole new set no questions asked! Dacor customer service has been a nightmare - so much back and forth... I tell everyone I know... DO NOT buy Dacor!!!

Our Dacor oven is 2 years old and the oven door stopped closing all the way, rending it inoperable. The company is now owned by Samsung. I tried to schedule a service call to repair/replace the door hinges. This should be a simple process. However, because I purchased the oven through a designer and Dacor dealer, I had to track down the order verification to demonstrate that I am the original owner of the oven (this is in addition to providing a copy of the receipt or proof of purchase). It took several days to resolve this issue with my designer and rep who sold me the oven. Then, I scheduled the service call on the phone only to receive an email hours later advising me that the service call had been cancelled. No explanation was provided. After rescheduling the service call several times only to have each call cancelled, something finally worked with Samsungs tracking system and the service call actually took place.Dacor is the Mercedes of ovens and I expect a service call to be a little more expensive. However, other providers of luxury products facilitate the product support to minimize customer aggravation. Samsung needs to work on its product support and customer service. I would not purchase a Dacor product again since there are several other manufacturers that provide comparable luxury kitchen appliances with much strong customer support.

We purchased the modernist collections 48” range, refrigerator and freezer, oven and microwave combo and dishwasher with a kitchen remodel 9 months ago. We had one issue with the dishwasher which was resolved, then another when is stopped mid-cycle. Repairman came out and was told we needed a new panel. Found out it was back-ordered. Well, it’s now been FOUR month without a dishwasher. We have contacted customer service and asked for other options and were told there was nothing they could do! When following up we have left messages and had our calls not returned, as has our service company. I have waited on the phone 3 times 30 minutes to talk to someone, because they won’t call back. We’ve asked to talk to a supervisor, and was told our information would be forwarded... 2 days later, no call. This is by far the WORST service I have ever had for ANY type of product.

We purchased the Dacor modernist Refrigerator, after waiting several weeks to get it installed we noticed the water dispenser did not function properly, we contacted the retailer whom we purchased the appliance from and after several back and forth emails to verify our proof of purchase they put us in touch with a repair technician. After a few days they came to our home to review the issue and noted that this was a known design issue with the refrigerator and that our house water pressure maybe too high and they would have to come back out and install a special valve to fix the issue. Later they called and said Dacor will not acknowledge this as their issue and to call a plumber. After spending over $20k on Dacor appliances I would have thought their white glove VIP customer service would be better. Buy Viking!