Warning! Do not buy Dacor appliances! We have had our appliances for three years now and all of them have had something wrong with them. Oven circuit panel went and had to be replaced! Dishwasher arm and seal broke and dishwasher leaks! Refrigerator freezer compressor went! Hood range switch broke and had to be replaced! Dacor is the worst appliances I have ever bought! Buyer beware!

Purchased a Dacor DT0227B wall oven. The first oven arrived damaged; the control panel was completely off the unit. We ordered a replacement oven which arrived today. Upon turning on the power, error codes C76 and C77 appeared on the control panel display. The installers phoned your service people who instructed them to remove the front panel and look for a loose wire. When they removed the front panel, the entire control board was just hanging free, not secured in place with any screws (it appeared that this was an assembly error). They found a wire hanging, secured it in place, reattached the control panel and applied power. At this time the error codes were no longer displayed and they were able to set the time. When they attempted to start up an oven cycle to test the unit, the Start/Continue button on the membrane keypad was not responding. Another call to your service team determined that the control panel would need to be replaced. 2 ovens within 2 weeks arrived DEAD! The quality is beyond unacceptable. I sent an e-mail to the CEO of the company before I posted this. I received a response from a QA guy. Any manufacturing company that thinks Quality is the responsibility of QA is working with a 1950s mindset!! Dacor is pitiful and will certainly not last as a company with this kind of quality and customer service!!

I purchased my first Dacor appliances in 1991, built a second house in 2005 and again purchased Dacor double ovens and a cooktop. Loved them! Remodeled my current home and again purchased the double ovens and a cooktop. The double oven, DTO230FS, which was installed in November 2015, 4 years ago, stopped working. I was roasting asparagus and we smelled what seemed to be burning plastic. The oven is used about 4 times a month, I have never used the self cleaning feature therefore it is surprising that it broke. The repairman said that the relay board was bad and will need to order the part. He estimates that it will be $600 to fix it. Sad that I need to incur the repair cost of an oven that is only 4 years old.

Purchased a Dacor Epicure ER36DSCH/NG RANGE and oven in 2007. Sad story, it never worked properly since day 1. Initially a gas burner did not light, they came and repaired it. Subsequently the door lock failed in the lock position - had that repaired. The door lock failed the next year again, this time thanksgiving, ruined the dinner. They fixed it but the following year the lower burner element failed at Thanksgiving. All my relatives know not to purchase a Dacor product. Problem is I am stuck with this boat anchor. The oven door motor has failed 3 more times and thankfully the service man showed me how to change it. Today we tried to bake some apple pies and found the oven temperature set at 450 was only 350 (bought an oven thermometer). This explains why it always takes so long to bake things. A complete piece of **, never ever buy one.

I remodeled a kitchen in a high end house and so wanted nice appliances. I had KitchenAid (which Id had a lot of issues with) for about 16 years. (Since I built the house - the fridge was rebuilt 3 times.) While looking for which appliances to use we were at an open house and a chef was cooking and giving a talk on the Dacor ovens in it. So... I reviewed a lot, liked what I read, and chose Dacor. I love them, the cook quality, the features, all of it. BUT my double oven had issues from the start. An annoyance at first with the built in Android but I didnt complain a lot. Move forward 1.5 years and the Android tablet built into it would freeze and not restart without throwing a jumper on fuse box. I called Dacor and they gave me a number of options, disable the Android because of a known issue and get $500 back, or - return the oven for full credit and theyd pay to have it removed (1.5 years later... cmon thats pretty awesome), or - pay $500 and move to the newest higher end model with steam cooking. Wow, talk about stand by your product! Ive never seen this before with an appliance manufacturer/vendor. Certainly wasnt my experience with KitchenAid. Anyway Im an advocate even though I had a problem and thought they deserved credit here.

I replaced my Thermador Wall ovens with Dacor because the size and I would have to do less retro-fitting of my cabinetry, this was a grave mistake. Here are the issues with Dacor.1. The high heat sensor trips and you need to call a service professional to have it reset. This gets very expensive. I have tripped mine three times, once baking a cake at 350 degrees, once during self-cleaning and another during normal cooking. The Dacor Service Help said this was a common problem because the heat sensor is located near to the touch panel.2. The oven vents from the bottom of the unit into the room heating my kitchen.3. The glass window does not seal so I have stains in-between the panes of glass. Not very attractive to stare at large drip stains.4. It takes an exceptionally long time to pre-heat oven and convection mode even longer.5. The temperature cycles through and does not maintain its cooking temperature causing underdone results and longer cooking times. This is especially challenging when cooking roasts and large turkeys because they may take up to an hour longer than expected.Overall, I do not recommend this product.

We purchased a Dacor wall oven when we renovated our kitchen in 2010. After five service calls, a replaced circuit board and broiler element, they found a broken wire which must have happened during clean cycle. I have been without an oven for two months and would not recommend buying a Dacor oven because I think it has a faulty design. The issue is still ongoing.

Dacor double oven range turns off by itself while baking - Disappointed in Dacor, especially today. Thanksgiving 2016: baking turkey. Sill baking turkey. I dont know when the oven decided to switch off this time, but I have an uncooked turkey and guests waiting. The oven has done this before, but because it was new I thought it was user error. Nope, the damn oven mysteriously turns off on its own. Incredibly irritated with Dacor. The range hood we also purchased is a joke. We remodeled our kitchen 1 year ago and wanted quality appliances. Bad move. Save your money, folks. Save your money.UPDATED ON 03/10/2017: Dacor sent a company out to fix the broken new oven. Oven still cannot hold its temperature (It takes FOREVER to heat then loses its heat while still showing a high temp). This time I have a recording on what happens when the oven automatically switches off. Disappointing when we spent nearly $10,000 in Dacor appliances for a kitchen remodel. DACOR, please have a rep contact me!!! Still waiting to hear back!!!

We had problems with it all the time. The front plastic cracked and ended up causing the oven not to work. We have spent (over the past 9 years) about $1,000 on repairs. Now, we just had it fixed and our new clock that was installed into the oven is running fast. After just being fixed, it takes 20 minutes to heat up to 400. Honestly, it always has been that way. We’re not happy with it at all. We bought a Sears brand oven for our church, and it works great, and the cost was only a third of what we paid for the Dacor oven. The Sears brand bakes just as good as the Dacor (when it works). I think it was a waste of money to buy this Dacor oven.

I purchased all Dacor appliances when our home was built 3 years ago. The Refrigerator has been serviced 2 times already and now requires manual defrosting every month to keep it functioning. Now the double ovens broken! These appliances are expensive and a total nightmare...never buy them!

Dacor Double Oven Model D0230 - I have had my oven since November 2011. I purchased an extended warranty at the time of buying the oven. Right after it was installed, I called and said they needed to come and adjust the temperature control. It was off at least 50 degrees. It never held the correct temperature. Since July, we have had to replace 2 relay boards, two other parts that should take care of erratic temperature. Then I noticed the gasket was turning black in the corner and my glass pack in the window was steaming up and not clearing. The extended warranty would not cover the glass replacement and I was charged $126. They said it was cosmetic, but this was so bad that I couldnt see through half the glass. The steam stained the glass and you could not clean it, because it was inside two pieces of glass. Do not buy a Dacor oven. In 38 months I have so many repairs that I have lost track.

Dacor Worst Oven Ever. Major kitchen remodel in 2005. Designer recommended Dacor for great styling and the fact that it was a 36 inch oven. Before the kitchen was even finished the control panel had to be replaced. Since 2005 our local repair shop has had to replace the circuit board 9 times. Same issue every time with not heating and board found every time to be burned out! Dacor replaced the first few boards free but we had to cover the labor. To date more than 5,000 in repairs. Dacor would not replace the oven and had terrible customer service. Its down for the 12th time and its headed to the junkyard this time. I cant see spending another dime on this lemon. Dont ever buy a Dacor!

My Epicure dishwasher is being replaced after 4 years of use. The racks are rusted. It leaks. And the spray arms are broken in two. The dishes need to be completely washed before putting in dishwasher. Do not purchase Dacor dishwasher.

First six month, dishwasher rusted on the inside. Dacor gave us a less expensive in its place. First year, microwave was repaired five times. Microwave has a piece of wood to hold the door in place. Wall Oven, the broiler never work. Present, range oven does not work at all. We have a repairman that is trying to get parts. Present, refrigeration control panel does not work, need repair. These appliances were to be a our luxury kitchen, but turn into a nightmare. Do not buy this appliance, you are wasting your money.

Dacor range - After I posted my comments on August 8th, I was contacted by Dacor customer service immediately and the new part was sent to me free of charge. I do have to pay the labor, but the part was what was expensive before. They did give me an explanation as to why this was happening - the hinges on the door wear out and the door doesnt shut properly so that heat escapes. Should this be happening with a stove that was this expensive? I dont think so, but I am happy with the customer service I received from Dacor this time.

I purchased my Dacor range in 07. After running the self clean cycle today, my oven wont heat up using convection or regular bake. Keep in mind, I had the entire electronic guts of the oven replaced in March 2011, 6 months ago after the same full failure. I paid $6,500 for this appliance. I wish I had my old GE oven back. This piece of equipment is only 4 years old. My husband and I dont use the oven often. What a huge disappointment! I will likely spend the next few days on the phone with customer service.

We just purchased our home in March of this year. The previous homeowner purchased a Dacor oven; it is electric & propane. She purchased the appliance after a complete home renovation in 2008. They lived in the home. After 1 year, they moved out and had it on the market. We purchased the home in 2012. As soon as we moved in, we noticed the oven was not working. We called an appliance repairman - $564.00 service call and part for a new relay switch. It was great; the oven worked. Not even a day later, an F1 error. We called them back out thinking they must have done something incorrectly. They then said we needed a new control panel. We did not have an additional $400.00. We just moved, so he said you could still use the oven. We did. We would use it and flip the breaker off so we did not have to hear the annoying beeping sound. Then I came home and bam - no display, no oven. We called a different Dacor certified appliance guy thinking the first company was just taking us for a ride and it was their fault. $572.00 later, we got a new control panel, but guess what, the technician did not even make it to his truck before beep, beep, F1. He came back in and then said we needed to replace the display screen - an additional $217.00 with no labor charge. We told the man to shove it. I had every plan of taking the oven to our back tank and using it for target practice. But in good business practice, since this company already invested $572.00, we could not ask them to eat the money, so we allowed a third fix of the oven. While the technician was here, the oven made a horrible loud sound and shot out flames. He insisted maybe it was due to it sitting for a week without use. He left. I never noticed this flame before when the oven worked despite the F1 beeping. Now it’s hit and miss. Some days it will shoot out a flame once until it reaches 200+ degrees and then you can hear the fan kick in. Some days, twice, I have had it happen 3 times. If my children were to open the door during this event, I am sure they would be seriously burned. At first I was thinking maybe it is normal for this oven to shoot out flames during preheat mode since after $1300.00 repairs maybe it is just not functioning correctly. But if it were a normal function of the product, to me it would do it every time consistently and not three times, or two times on some occasions. I hate to admit this but I am almost fearful of using my oven. I currently have a pie to put in for dinner and I’m thinking its 3:09 pm; I could set the oven to preheat while I run to get my kids from school so if it decides to blow up, I am not home and that is pretty sad. The last repairman we had come out said in his personal opinion, he wouldn’t have repaired the oven, because they are known for issues, and he would have gone to Lowes and spent $300.00 on any off brand stove first. We have considered that, but this stove is extra-wide and the cabinetry is built around it. So for us to purchase an oven to slide right back in it would be another $1300.00-$2000.00. We have issues with the burners not always wanting to light. I almost caught on fire lighting one because it shot out flames when it decided to finally ignite. Sometimes it just clicks. Currently, I am down to two burners when just two days ago all six were working just fine. Over Thanksgiving, it took no kidding 1-hour to cook brown and serve rolls because the oven did not reach the set temperature. We stuck my husband’s bbq thermometer to see. It was 256 degrees, not the desired 350 degrees. Does this stove have warranty? We have no clue as the previous homeowner purchased the stove. She claims to have spent $5,000.00 on this stove or more during their purchase. We do not have warranty on our home so for each repair, it is out of pocket for us, and currently we really are thinking any knock off brand at Lowes would be a better product than a Dacor oven and less of a safety hazard for our family.

Reports that this microwave was not powerful enough because it’s “only” 1100 watts are a head scratcher. It performs as well as and is as sturdy as our previous DMW2420S that lasted 16 years!

When I completely remodeled my kitchen 6 years ago, I actually went AGAINST the advice of my appliance dealer and kitchen designer and insisted on buying the Dacor 30 double convection wall oven. Id been longing for Dacor ovens for years and though they gently tried to steer me towards Miele or Electrolux, I dug in my heels. Ive regretted ever since. Since first use, my electronic display has not been without an error message. Every time I go to turn on the oven, theres a message telling me to clean the convection fan filter. I called Dacor and they told me to ignore it! It was a mistaken message. Still, I cleaned them repeatedly to no avail. The main electronic circuit board on the oven has gone out three times. They paid for it the first time because it was under warranty. The second time they sold me the part at a discount but I had to pay for the service call. Total cost to me: $480. The third time, I had to pay for everything myself. Total cost to me: $870. They told me its because I broiled with the door open. I have NEVER broiled with the door open! The inside lights go on and off randomly. The temperature probe has NEVER worked properly. Last week, I was preheating the oven to bake some cookies and an alarm went off giving me a cooling fan error message. The oven turned off and I cant get it to turn back on. I called Dacor customer service twice so far and the first time they told me they would research the issue and call me back. They NEVER CALLED. I called again and they told me they could ship me the part and I could pay for the service call. The lower oven is currently working so I havent done anything yet, but the oven originally cost me well over $5,000. I have put another $1,300 into it. Im not about to spend another $500-$600 on this complete waste of money. Bottom Line: Dacor sells junk for exorbitant prices and refuses to stand behind their products. I was an idiot to fall for the Only True Convection Oven in the market line. Im buying a Miele or a GE to replace.

I completed a 7-month total remodel of our kitchen and family room, which were connected in November 2007. The kitchen remodel cost $18,000 for various Dacor appliances including the Millenia series of wall oven MOV130S; warming drawer MWDV30; and 42 island hood DHI42130. The remaining includes the huge 30 Epicure dishwasher ED30SCP, 36 cooktop EG366SCH, and beverage center EF24LBCSS. All have the beautiful copper accent package and make for highly attractive appliances. We constantly receive accolades for them. If only they werent absolute garbage functionally and reliability-wise. Others have remarked how the ignitors on the cooktop continually spark, even after the light off. After contacting Dacor and waiting 2 weeks for the repair, for which Dacor sent the wrong part and caused another 2-week delay, the repairman had to rip off the front accent lip of the cooktop to reach the base which significantly dented the front lip. The ignitor worked like a champ for 2 days, then click, click, click - constant ignitions. So I cleaned around the ignitor tip with 409, dried it and it worked flawlessly. Thanks Dacor for your own product ignorance and my now dented cooktop. It has worked well since and is a sound product, so far. If only my luck held out.Next, the wall oven. Very beautiful and my control panel has held out (fingers faithlessly crossed). The oven isnt calibrated though, so follow cooking directions at your own risk. This oven will burn your food if you set the temp and timer to the recommended settings. I have to take off 25-50 degrees and 5-10 minutes of requested cook time or I will smoke any meal. After 2 years of use, I decided to use the cleaning cycle - following the directions to the letter. Forty five minutes into the cycle and kaboo! The front window shattered. Dacor says $700+ for glass replacement; I say send me the part and Ill do it. I got the discounted part for $68; spent 3 hours cleaning and reassembling with care; and the window has held, but I havent tried the cleaning cycle since. Why roll the dice again?Ah, now my fave garbage Dacor appliance - the interminable dishwasher. Truly engineered by the diabolical. I just completed my fourth major repair after 5 years of use. First, the drain valve failed after a few months of use causing flood and was replaced under warranty. Then the door seal failed (more flooding) and was also repaired and replaced under warranty. The dishwasher stinks, by the way, as the unit cannot evaporate effectively during drying cycle due to ridiculously poor rear venting design. So I have to leave the door wide open for hours after use to facilitate drying and stench reduction. The control panel/circuit board has fried twice now in the last 3 years - it just starts erratically beeping and refuses to take input, even with a power reset. Both technicians stated the design and quality of the board is third world, which likely is exactly where Dacor outsourced the garbage.The island hood and warming drawer have worked well, and the beverage center has been reliable but maddeningly causes back left cans of soda to freeze and explode occasionally; even with the set temperature raised to now 45 degrees. Fun to clean up after coming home from a long trip. My expectations are so laughingly low now for these Dacor products that I dont bat an eye with the frozen soda muck this fridge occasionally produces. Customer service though has been helpful and thankfully, American. They have replaced both circuit boards for free well out of warranty. I have only appreciation and great sympathy for the customer service folks who Ive spoken with. I love my kitchen, but hate the appliances in it. Never again Dacor. Never again.

Dacor customer service contacted me and worked with me and the appliance repair company to get the proper parts to fix the oven. Everything is fine! We once again really love our Dacor wall oven.

We purchased this oven February 2009. On 6/7/11, we had to replace the touch pad assembly. On 12/16/13, we again had to replace the touch pad assembly with a cost of repair to this point of over $900.00. The over cost $2,395.00 when purchased. On 3/16/14, while on convection/bake the oven switched over to broil. On 3/20/14, a repairman came to the house. The condition did not replicate but the repairman, in conversation with Dacor, determined that the fix, if this should happen again, would require the replacement of the relay board and ERC control at a cost of $700.00. On 3/27/14, while on convection/bake, the oven switched over to broil. I called Dacor and was forced to leave a message.

I have owned a Dacor Convection microwave for a few years and is so far the best Ive ever owned. It works great every time, has great preset features and also has a great stainless steel look. Great Product.

I bought my Dacor epicure 36 duel fuel range in 1998. First stove: oven door did not close, spark modulator out. They tried to fix it but failed. They sent me a new stove. #2 stove: same problem with spark modulator. Couldnt use any burner without the constant clicking. Oven didnt bake evenly. Complained. Stove: #3: same problems. Dacor sent me a letter to grade them on their stoves and service. I blasted them. They called me and ask if I wanted my money back or another stove. Stupidly I took the stove. This was 5 years since the original purchase. Ive had this stove #4 for 13 years. Door is and always has been unable to close. I use a stick to close it. Now the relay board is out. Frankly I so love the looks of the stove and I cant afford to get a new one. Original was 5200. Now they are 6700 and I would probably have the same problems. So I am going to try and fix this stove myself. I will never buy Dacor anything ever again, even if I could afford it. When they offer your money back, take it. The service was responsive although didnt solve the problem through 4 stoves. I would gather from that, the design is bad. My mother has a old 1940 gas stove that still works. Gas stoves should not be that complicated.

ZERO STARS if I could but DISAPPOINTED - if I had to use one word to describe our experience with Dacor with not only our $8K+ 42 Built In Refrigerator that is sitting at 70+ degrees in the freezer and fridge sections but SO DISAPPOINTED with their poor customer service and lack of concern resolution tools for their team to even try to help.They are supposed to have high end luxury products. With that, anyone would expect to have a luxury customer experience. However, our family has been WITHOUT a working unit since January 6th. That is less than a month from when we had it installed but almost a month from today. We followed the proper protocols to get it repaired. Took almost two weeks to even get a technician. Once we did, he confirmed it needed to be replaced. We got approval and now learned we have wait another 2-3 weeks to get a separate decision to be made.Requested if there is any way to escalate our concerns but cant even talk to a supervisor for another 24-48 hours... Apparently they will call when it is convenient to them. Dacor - have some empathy for your customers! Imagine paying for a high end product to have no working fridge or freezer for a family of 6. Not sure how this is an acceptable practice. POOR QUALITY, UNTRUSTWORTHY, DOES NOT CARE ABOUT THEIR CUSTOMERS.

My Dacor Preference 30 double wall oven (model PCD227R) was installed on 5-14-2004. On 12-31-2007, I replaced the upper oven high limit switch for cost $146.56. On 5-19-2010, I reset the lower oven high limit switch for cost $95.00. On 8-27-11, I replaced main control panel (Bezel Assembly), whose parts cost $271.10. On 12-14-2011, I replaced the main relay board for $214.02. On 1-16-2012, I replaced main relay board again, and it is under warranty. On 2-3-12, I replaced upper oven temperature sensor for $32.09. I am awaiting authorized Dacor service technician to calibrate both ovens.

I own a complete Dacor Kitchen, with many appliances. They are the highlights of my Home. Great features: fast induction cooktop with an efficient silent hood, versatile refrigerator, reliable oven, and of course the always dependable dishwasher. This is My Dacor Kitchen!

We placed the new Dacor appliances that we’ve purchased in our second home in Big Bear Lake, California. The fact is we were in our second home approximately 10 times in the first two years. We had trouble with our Dacor dishwasher from the beginning. When you close the door, it wouldnt engage unless you close the door a number of times. It became progressively worse to the point where we brought out another repairperson - this time a certified Dacor repairperson. He got the washer going for a few minutes, only to not being able to complete a full cycle. We received an initial $89.95 bill, and during another contact we would have to pay an additional $400-plus for a motherboard and labor. We contacted Dacor, along with the contractor, a number of times. We had the history of this dishwasher which is causing problems.Dacor would not make it good, even though we spent more than $10,000 on other Dacor kitchen products. It simply doesnt make sense to me to not fix a sub-par dishwasher to keep a customer happy. Now, we are angry and will go on a number of sites to advertise our plight. We will install a new Bosch dishwasher as we have no confidence in Dacor and even less in their customer relations division.

We purchased a Dacor wall oven to replace a GE oven that was outdated. We thought we were getting a premium appliance, but after less than a year and just before the holidays it quit with a code on the control panel we couldnt find in the owners manual. We had a serviceman out and the cost of the part and the service call was more than we paid for the oven! It now sits there, useless and a reminder to never buy Dacor anything!

For the second time in 7 years our Dacor ERD 48 Range has failed us. Just in time for our New Years Day dinner. Neither of the two ovens will heat. We are now encountering the exact same problem. We spent $1000 the first time replacing the board. We cannot afford to do it twice.

The wall oven’s glass was damaged by a guest. Customer service at Dacor was exceptional. Within a day of advising Dacor’s customer service, I received a call from the service man and the replacement was installed the very next day. The service man was considerate by calling first and coming exactly when he said he would. He was very professional as he replaced the glass in a matter of minutes. I would choose Dacor again.

I purchased a 48 Dacor Epicure stove in October 2010. We moved into our home in November just in time for Thanksgiving. We remodeled the kitchen and the stove is the focal point. When I heated the two ovens, the pre-heat mode stayed on but the ovens went to 600 degrees plus. My oven thermometers only read to 600. That happens every time and the fans stay on for hours. After many service calls, we have determined that the oven is going into a cleaning mode every time and is wired backwards. Dacor is ignoring me.

This is a follow-up to my prior comments on the 30 Dacor wall oven. After posting the prior complaint, a Dacor customer service representative emailed me immediately the following day asking for details on the problem. The Dacor rep immediately called my repairman, notified me that they were working on a solution, and then followed up with a solution that exceeded my expectations. We are very satisfied with the outcome and should have called Dacor directly at the onset. Thank you Dacor!

I bought a 30 Dacor Double Oven (EO230SCH), 36 cooktop, warming drawer and matching convection microwave. Well over $10k. The microwave has been replaced as it died early within the first year while cooking popcorn - nearly started a fire in the kitchen... However the cooktop igniter died at 4 years and now the wall oven is on its third control board in years 3, 4 and 5. Nothing is under warranty and they want nothing to do with me now. The replacement oven controls cost ~$400 each plus installation. So after all this expense, I have invested $1,200 more in replacement parts and the cooktop needs an aim & flame to light. Total crap. Im going to replace all of this and will never go back to Dacor. I took the time to write this so that others will not waste their time with what I have to assume is the worst quality in the industry. Please dont waste your money.

We have an 11 year old Dacor double oven with convection on top. The relay board malfunctioned and there are no parts to repair this. All Dacor would tell us is that they dont carry the parts anymore. Evidently, they are not required by law beyond about 8 years and that appears to be all they do. Our appliance repair person even contacted a company that rebuilds electronics and they cant get parts for this board. It is unbelievable considering what we paid for the oven. So we now have to replace it. Dacor offered us a discount on a new one. Not good enough. I cant imagine putting another Dacor product in. Two appliance service people have told me that Dacor has this reputation and they would not put them in their own houses.

Our new ranch has three Dacor microwaves, only one of which has had a few months of use. The others have very limited use. To this point weve not had problems, but given the opportunity to redo the purchases wed go with a popular brand, i.e., LG, GE, Panasonic. They are more flexible, parts are available, and all three combined would probably cost less than one of these. In fairness, I personally feel the same about our other high end appliances, Wolf, Viking, Sub-Zero and Asko. None beats our former appliances. Maybe its just about show.

This is our second Dacor wall oven. It is approximately 6 yrs old. December 22/14, I was cooking a Christmas turkey as per usual, and I noticed an odd smell about 40 mins. into cooking. Checking the turkey, the temp. was at 500 degrees and on broil. I burned holes in my oven mitts on the roaster taking it out. Even though I set the temp. at 325 convection roast, it reset itself to 500 broil. Nothing works except the clock. Called repair guy after the holidays. Said it is a control panel behind the keypad area. Ordered the part. Been waiting 4 months now for this part. Now, no Easter dinner either. After reading these complaints, I am worried that this part replacement may not be the end of it.

We purchased a Dacor oven stove top. It is about 10 yrs old now. 3 years ago we had a problem with the ignitor and had it repaired and paid over $200.00 for the repair. 3 Years later we are experiencing a similar problem with the ignitors clicking on and not turning off. I have called for repairs on this but expect this will cost me some more money. I have been online and have seen similar complaints leading to believe that this is a common problem and I would avoid purchasing Dacor ignitor products for the stove top, until resolved.

I have been very disappointed in the reliability of our Dacor refrigerator, model EF42BDCBSS, purchased in 2007. The first circuit board went out in 2008 within 6 months of the initial purchase. A replacement part could not be located. It was still under warranty so they replaced the whole unit. In 2010, we had to have another repair to regulate the temperature of the freezer. Last week (October 2012), the circuit board went out again! Even though the unit itself is less than five years old, it is no longer under warranty. Dacor goes by the original installation date. I contacted Dacor and spoke with LS who basically stated that all they could offer was a discount on the part. This repair is costing us over $650, not including the loss of food. We paid to have the part second day. When we called back the next day to get a tracking number for the shipment of the part, we were told by another representative that the part had not shipped because it was out of stock in the default warehouse. He was able to locate it in another warehouse and get it shipped the same day. I called LS back and she stated that she never promised when it would ship, but when it did, it would go second day. I would not expect this type of repair cost and attitude on a refrigerator that was over $9,000 when new. Now, I am concerned with the liability of our range and microwave, which are of the same Dacor brand. The main reason I took the time to write this email is to make retailers aware of the situation and ask that you seriously look at the reputation of the Dacor appliance line and decide if you really want to promote this product to your customers. Dacor could care less about their customers and/or reputation.

I was a bit anxious when I purchased my Dacor range because I really didn’t know how it would perform. A year later and I couldn’t be happier. I love my Dacor 30” range. It has been one of the best purchases ever.

I bought DCM24S DACOR 1.5 CU CONVECTION MICROWAVE-SS and after few months of using this product its banded on the back wall of the microwave that supposedly resulted from improper turntable placement which caused the turntable tray to make contact with the back of the oven. The quality of the product is very poorly, dont buy Dacor product!

The ovens needs a new latch kit and a mew control panel every year. It has been repaired 15 times. So many issues but those are the most consistent problem areas. Dacor should have replaced our range the first year. Even the repairman says everyone has had the same issues. For what I have paid in repairs I could have bought a new range.

Over ten years of using my Dacor oven, I have spent $1595 in repair bills to keep it going. It cost $1875 originally and I would have purchased a more reliable brand if I had known how much trouble the oven would cause me.

We purchased this range after remodeling our kitchen. We opted for the Dacor because of the deep oven that the other high end ovens did not have. I am an avid baker so this was a plus. After a year and half the oven stopped working, it was not getting hot. Thankfully is was still under warranty and it was repaired. The technician determined it was the oven control thermostat that was not working. Fast forward two years and again the same problem, along with the right front burner now also not working. And wouldnt you know it, the warranty is expired. Another technician came out again and stated to fixed the two problems it would be approx $250.00 just for labor and not including parts. CRAZY INSANE!!! If we would have known all the problems and we would have purchased either a Wolf, a Thermador or even a Monogram. How can so many issues and problems be happening with an range that is only 4 years old? Especially one that costs over $6000. It has to be a lemon or poorly manufactured. Ive contacted Dacor and was told they need to review my file to make a determination on what they want to do. REALLY, you dont need to be a rocket scientist to know there is a problem. Theres lemon laws for cars, why not appliances????

Dacor appliances were installed in a new home I purchased. The refrigerator has been out of service every single year since purchasing the home. So far, two thermistors, one power supply board, one drip pan heater and one ice maker. Every time the unit fails, I have to wait several days for the authorized service provider to come to the house. That will then result in the need to secure a part that will require anywhere from three days to three weeks before the unit can be placed back into service. As you might guess, perishables dont last that long, so every event results in the loss of hundreds of dollars of food. After yet another extended outage experience, I called Dacor to find out what they might propose to make sure my refrigerator actually performs in a reliable manner (apparently I didnt get the fridge with that feature). The short version of the story is that they not only failed to ever apologize for the fact that their product doesnt work, they insisted I produce detailed documentation covering the last four years of service before they would consider taking any action. Shame on me for not keeping all the invoices from the two service companies. After numerous exchanges, an offer to pay for the part associated with the last repair, not the labor, was the best they could do. Apparently, $250 is too much for Dacor to invest in a customer who has paid several thousand dollars in repair bills and lost hundreds of dollars of food for a unit that is four years old. This is a company who obviously cannot design a product that works consistently and cant provide after sales support in an effective manner.

Our Dacor wall oven (model MOH 1305) is the subject of my concern. Purchased with confidence in Dacor’s advertising in 2008. The oven has had multiple visits by a Dacor authorized repair company who along with a Dacor technician determined that the oven needed a relay board replacement. This relay board has been replaced twice and has failed after installation both times. The relay board provided by Dacor appears to be the problem. Each repair/service call costs approximately $300.00 with no guarantee that the next relay board will work. Our conversations with Dacor give us no satisfaction. Dacor now tells us that our “superior product” of 11 years is just too old. Additionally, they tell us that Dacor products are “superior products” that are designed to last somewhere between 10 to 15 years. There is no excuse for Dacor since the replacement relay boards they are sending us seem to be defective. Their excuse that we have an “old” oven is wrong since the problem is with their defective replacement parts. Beware consumers when thinking about purchasing Dacor products.

The Discovery Model 30 electric wall oven - After 6 years, the oven failed. The fan motor went out and at the same time, we were advised by a very reputable appliance repair recommended by Dacor that we need to also replace the computer or brain. Total cost of repair: $1150 with a warranty of one year.

I called the customer service number regarding my double oven. It just randomly beeps and now turns off. No error code displayed. It has done this on and off since 2003. Now it is happening all the time. I called customer service and they seemed to act like it is my fault and I need a new touch pad. I inquired and this is a recurring problem with this model. I could not get a straight answer from the person I was talking to. He just told me that if the repairman says I need a new touch pad, then I need to get one. Well I have been doing some research and this is a problem that seems to be haunting more people than I. We own a Dacor gas cooktop that has had to have a switch repaired. We own a microwave that has had two new circuit boards and now a beeping oven that gives no error code and turns off by itself. My advice, do not buy Dacor appliances.

We have had problems with the igniter switch which clicks when I have a large pan or pot on the stove. My husband has tried cleaning the igniter tip with a brush as well as the removable ring but we still have that problem. We also have a Dacor microwave that seems to blow a door fuse pretty often that has to be replaced.

The oven temperatures fluctuate while baking. The company was at first responsive. They replaced the oven controller and the temperature sensor. This did not fix the problem. When I called and left messages, there was no call back or response. Very poor customer service.

We purchased this high end Dacor range (Dacor Renaissance ER30G) new in 2011 from the Appliance Loft here in Cincinnati. It was dropped off and installed and would not operate right out of the box. A repair was made and everything worked (unless you count the indicator lights on the knobs, they all went out after approx 14 months). This past November the oven went dead. A1 appliance came out: Determined new control board needed, ordered and installed. Thanksgiving Day, oven dead. A1 comes back, reset the High Temp Fuse. Oven dead 4 days later, A1 returns with a new HTF. Dec 22, Oven dead. As soon as The holiday is over we will call another repair shop and start looking at replacing this unreliable piece of eye candy. Open comment to Dacors design engineers, quality control engineers and management. You should be totally ashamed about this product youve designed. You are supposed to represent the best in American design and quality and this falls below that of low end appliances out of China. See you in small claims court.

I am writing to complain about our Dacor dual fuel stove that we purchased in 1998 when we built our house. Initially things went well, and I enjoyed baking in the oven and the convenience of the gas stove top when we had power issues. But then the honeymoon ended, and the problems started. After completing our first self clean cycle, we started getting the F1 code, and noticed cracks in the front on the stove. Our repair guy came out, took a look, and then informed me that Dacor had had numerous problems, and were not so good about living up to their warranty. He was right, Dacor felt in no way that they should help resolve our problem. With 4 kids, you cant just go without a stove, so we paid for the parts and repair. I figured it was just a one time thing, but I was wrong. We are now again looking at replacing the same part just 3 years later again with cracks and the F1 code. Dacor should be ashamed. Do the math. If they walk away from responsibility on all of these faulty products that average $5,000 a piece, shouldnt they have the money to pay for the fixes or maybe hire better engineers? They need to be held accountable for this mess. I need my oven back on!!!! And after the money we have paid for repairs, light bulbs, and parts...... the rest of the care should be free and on them.

We did a complete kitchen remodel 2 years ago. My husband talked me into purchasing american made over the Bosch products that I preferred. This has been a horrible experience. The dishwasher does not clean. I was told to prime the water and purchase the higher end platinum packs. That did not work, then it was add lemi shine. That has not worked. The water never completely drains, ugh old water. A service tech could not tell me where the rinse aid indicator light was and insisted mine did not come with one! Microwave does not heat in an adequate time. All listed times I have to double time if not more. I was told to put a Rubbermaid container over the food product to insulate the waves... ha! Oven does not regulate heat. when I go to increase the heat during stated recipe, the screen always say 50 even though I would have it at 375. I was told it always will revert back to 350, really. I had all Kenmore appliances prior to the Dacor and never had a problem... Do not buy, I wish I hadnt. We are filing this with BBB and headed to small claims court.. This should be fun. I hope Dacor sees this.

Arrived in good condition and so far works perfectly. Delivery was delayed by one day because of the incompetence of my local mail service. I bought this microwave, as others have described, to replace a 13 year old Dacor that had not really died but had lost the electronic screen. We put magic marker numbers on the display screen where the numbers had been 5 years ago and kept using all the functions. I decided to replace as, without the display screen, I could not do anything semi sophisticated with this microwave but its motor and microwave capacity was still going strong. This model fits perfectly into the previous 24/27 trim kit. Unfortunately our other trim kit is white to match our old microwave. Decor only has stainless steel now. And the new trim kit for this microwave is flat without the vent slats (plus costs over $300!). From the placement in our cabinet, I think the vented slats are really important to dissipate heat and am puzzled by the change in design by Dacor. The slats are a little tedious to clean but as a TV is above the microwave and an oven below I want the heat to have a better place to go. Ebay has the old trim kit in stainless steel but so far the expense seems excessive for just the outside piece. The internal support bracket for the new microwave is exactly the same as for the previous model so the only part of the trim kit needed for my microwave is the outside frame. This newer model works very similarly to the older version. I am delighted Dacor still makes this microwave to fit my space 13 to 15 years later.

I have had nothing but trouble with a wall oven I bought in 2010. Basically just bad electronics. I finally replaced the oven in 2014 and had to get another Dacor to fit the opening. The new unit still does not heat evenly and is consistently off by about 50 degrees. Customer service is not helpful at all. Local repair shops cant really fix issues. Terrible company. Cant figure out how they stay in business.

I have had my 30 inch Dacor Dual Fuel Range since 2002. In the past month, the oven door seems to be falling apart. I had to replace the oven door handle after the handle cracked in the spots on the right hand side where the screws go in. When I tried to screw the new handle in, I noticed that the front panel on the door is lifting away from the door. It is more separated on the right hand side which leads me to believe that it is the reason that the handle cracked on that side. As a result, the handle cannot be properly installed. The only way this can be repaired is to call someone in to do it and it will either have to be glued together or the whole door would need replacing. Reading these forums, Im worried that my oven problems are just beginning and I dont want to start sinking money into this oven. I purchased a Dacor as I believed it was a high quality product and that it would be worth the money and last a long time. This type of problem should not be occurring. I do not consider 10 years a long time for a product like this. My sister has had her Jenn Air oven for almost 20 years and it has no signs of wearing out.

Oh how I wish I never bought a Dacor! It has been nothing but problems. I figured I bought a lemon but after reading other reviews its just not a good product with not very good customer service either. I have had repairs every year, and even after repairs it still isnt functioning as it should. The first problem I had was the whole glass window blew out during baking, which seems to me is a huge liability. The company said that shouldnt happen but is out of warranty and would give me a discount on the glass. I thought that was better than nothing but then 6 months later the relay went out, then baking temps were all over the place in the oven so they said I needed a new motherboard and they said both ovens needed it. So those were repaired. Oh ya and the light in the bigger oven hasnt worked past the first year even after having the light changed and some electrical stuff done on it. Then I had the bulbs changed due to irregular oven temps. The temps are still all over the place to this day.The back right corner gets too dark. The front left doesnt brown and is a lower temp. Now Im having problems with the oven turning off during baking and when using broil in the small oven it causes the large ovens probe alarm to go on and offer at least for an hour. Dacor didnt help me with anything past the glass and its only been 7 months since the new motherboards were put in. I cant afford to buy a new oven at this time and so I only use the small oven mainly since the larger has so many problems. Do yourself a favor and never buy a Dacor!

I will NEVER buy Dacor EVER again. We built a house and after looking at other high-end appliance makers and upon my mothers strong recommendation, we installed all Dacor appliances in our new kitchen. My mother based her recommendation of Dacor appliances due to what she explained as their excellent customer service. HA!! Less than 3 years after installing our pricey Dacor Epicure over-sized dishwasher it has rusted racks -- top and bottom! After experiencing a very painful, drawn-out and EXPENSIVE process of getting our racks replaced, I am not confident AT ALL that our frustrations with this dishwasher are over yet. The new retrofit slides on the top rack are so lightweight I cant imagine they will effectively operate for years to come. I have difficulty closing my dishwasher properly now and have to check each time I run it for leaks on the floor. Ive given up on my Dacor dishwasher and have resigned myself to eventually replacing it. NEVER buy Dacor!

I have an Dacor column fridge and after 18 mths (under warrant), its not cooling. Its been 3 weeks, 2 repair visits and Im still out of fridge. Repair person said this is a known issue. If this is the case, Dacor should be proactive and reaching out to consumers under warranty to get this fixed instead of waiting for complaints. Interior trim kit is not included in purchase price which is ridiculous for the price of this fridge. Would not recommend!

When I pay top-dollars for a supposedly high-end product, I would expect performance and durability. That is not the case with Dacor. This manufacturer charges top-dollars for their appliances but their products do not live up to expectations. I purchased a Dacor gas cooktop range, and within a year several blue-indicator lights on the knobs (which indicate the gas is on) failed. At that time it was covered under warranty, and even then it was a hassle to get the repair technician to come out and take the range out to get to the electronic parts. After replacing two of the lights, the other lights failed as well, and then the replaced lights eventually went out. Now, only one out of the five lights work. After a year, the appliance is no longer under warranty, and it is too expensive to get it serviced. Its not only a cosmetic issue, but a safety one as well.Were in the market for a single wall-oven, and I considered a Dacor for its clean and stylish design. However, after reading the reviews about Dacor, Im veering away from this company. Sadly, as much as I want to support a Made in America company, the pride of workmanship and customer service doesnt live up to this companys branding.

I have a 4 year old Dacor Renaissance 36 in gas range. The thermostat is broken, the self-clean cycle doesnt work due to a broken lock and the oven indicator light stopped working about 2 years ago. Pros: It is an attractive oven with the knobs that light up blue when on and the burners all work fine but that is it! The technician told me ALL parts I need are on backorder due to Dacor being bought out by Samsung 2 years ago and COVID related delays. He also told me there is no ETA on those parts and said it could be an unknown amount of months. So now I dont have an oven for an unknown amount of time. This is unacceptable. I was sharing my frustrations with a friend who recommended I post this on Dacor Applicances Facebook page. He thought I would get an immediate helpful response. So I did. It was taken down not more than 3 minutes after it was posted! They never even reached out. Pretty poor company service. I will never buy Dacor anything again. Even when the oven was working ok - it never kept good heat and the self-clean cycle never cleaned well - there was lots of grease residue left behind. This is a poor quality company all around. Believe the negative reviews. If I could give negative stars, I would.

DONT recommend model #MOH130. We were so impressed with the options that this oven came with. Sadly, with all the bells and whistles also came a ton of repairs. After the 4th repair, our service rep said the relay board needed to be switched out. (Half of the service men who came to my house seemed to be grasping at straws trying to come up with an explanation why the temperature was fluctuating, or why it took so long to heat up, etc.) Then I get to wait 2 weeks for a part to be ordered/arrived and re-schedule service. Last week got code U22 - oven wont even turn on. This oven is only 6 years old. NO THANKS - NEVER AGAIN will I buy anything from this company.

This range has never cooked anything well, overlooked and undercooked. Several technician visits, board replaced, thermostat replaced, starts error messages and clicking all on its own. Recently the cooktop has exploded with a big BOOM 3 times. We finally turned off the gas and Im cooking outside with the camping stove and BBQ. I am so upset about the explosions that I am shaking. Today it exploded while all knobs were OFF. Im thinking about getting an attorney. IF my house caught on fire my insurance would not pay unless I do everything in my power to mitigate damages. No gas should work, but I would like to be able to cook in my beautiful kitchen with my granddaughter. Help!

We bought 3 very expensive Dacor appliances when we built our home 12 years ago. They have been a total disappointment. The microwave was replaced after just a couple of years when it just stopped working properly - including needing to stop it by opening the door! The wall ovens have needed many minor repairs which have amounted to several hundred dollars after labor charges. I see on this post others have had to repair the hinges! Ours have been replaced twice! The broiler came loose and was hanging on one side. The internal light also goes on and off by itself - sometimes in quick succession. At times, it stays on and cannot be turned off by the light button but by banging the front of the oven! Ridiculous! The cooktop cooks very unevenly. It goes from simmer to boiling over. The ceramic material did not hold up very well either. It is supposed to clean easy. But there are spills that have left permanent stains and we will be replacing that as well. We have also had Customer Service tell us items have been discontinued so we have no choice but to replace these appliances since replacement parts cannot be purchased any longer. This is a warning to anyone considering Dacor - DONT WASTE YOUR MONEY! There are far better appliances out there!

We had our whole kitchen renovated and purchased Dacor appliances through Caplans Appliances. We purchased the appliances in the summer of 2019 and they were shipped shortly after. Since our kitchen was still under construction the appliances sat in our home. They were installed the second week of November. Two months ago, I woke up to a sucking noise from the dishwasher. The dishwasher had a code of LC. We removed the custom kick plate to realize that there was water damage. Dacor has been contacted on numerous occasions regarding this and the dishwasher continues to leak. We have had 5 service calls to house and the problem persists. The seal has been replaced twice in a 2 week period. The repair company HARGTA gives us a window and does not show up at that time causing me to sit around all day waiting for them and then some days having to cancel work. Dacor customer service continues to say the Regional Tech Manager will be the one to provide the resolution and we have not heard from them yet. The reviews on here clearly indicate that the dishwasher leaks. We are risking damaging our floors which were put in at the same of our renovation. Looking for a resolution ASAP. To those considering Dacor appliances do your research.

We bought a whole new kitchen's worth of Dacor appliances - the Modernist line. It's too soon to review their performance, but so far they work well and look fabulous. Most importantly, I had an issue registering my appliances for warranty. I sent an email and not only did they resolve all my issues, registered everything for me, they also notified me I was eligible for an extended free warranty program, and they set it all up for me without any effort on my part. I wouldn't have even known if they hadn't done it for me. So far, I'd say that they have stellar customer service. When researching online before making the choice to go with Dacor, I had trouble finding information and reviews. I wanted to make sure and share my good experience since all too often people only share when they have had a negative one. I hope this is helpful to someone looking to buy!

Front bevel of my first rsd30 range purchased in California in 1999 cracked within nine months. Dacor said it was a defect in the design and would fix it for free. I sold the house in 2001 but the range was still not fixed. I moved to Nevada and bought a new rsd30 range and same thing happened within six months. It took a year to get it fixed at their expense. This bevel also cracked again for the second time in March 2011. Their response to this was to offer me a new bevel for $180 and I would have to pay for the installation. I declined the offer. The bevel is still cracked at this time. At the same time, I bought a PMOR30 over the range microwave and the front handle broke at least four times. And finally, the whole thing broke down and was not repairable. In Aug. 2008, I contacted Dacor and they agreed to replace it with a new DMT2420 over the counter microwave for half the price ($390). Last week, this one blew up on me. Sparks were coming out through the side and a big hole in the removable shield and burn damage to the wall of the unit. I do not believe this unit is repairable. I contacted Michael at Dacor. He apologized and said that theres nothing they can do about it as it is out of warranty but they will look into it. What I want at this point is my money back that I paid for ($390) and for them to pick up the unit and get it out of my house. I will never buy another Dacor product again.

Our dacor appliances are 8 years old. Four or five times a year we need to have the technician to come by to fix something in our kitchen, dishwasher, built in fan for our stove top or refrigerator. These items are high price items-- should not have so many problems.

This is a follow-up to my initial complaint, which was posted on November 28, 2011, and an updated posting on December 27, concerning problems with our Dacor range. What we learned was that the local appliance shop that services Dacor quit working on Dacor appliances, so we were left with no repair company. We were contacted by the customer service representative from Dacor, who has been very diligent in working with us to find a solution.Yesterday, the Dacor regional service supervisor from Washington came to Casper to work on our oven, which is now totally functional. Pretty amazing customer service! He did share with us Dacors challenges in getting qualified local service companies, especially in smaller towns. I applaud Dacor for going the extra mile (1,000+ miles, to be more accurate) for us.

Talked into spending $4700 on a wall oven on the recommendation of an appliance retailer. My concern was even baking and reliability. Was told I would be very happy as Dacor was best on the market. Well long story short, it never cooked evenly and after 8 years quit working. Had to lug the heavy oven to the city to an approved service provider. They thought it was the relay board (told the brains of the oven). Service provider changed several things (sensors, board and whatever else). Nothing solved problem. Phoned me and said I was looking at minimum $2000 and up. He threw oven in garbage. We didn’t even send the gas money to bring the dud home.Thought it should last longer than 8 years. I phoned Dacor. They wanted to know exactly what the problem and diagnosis was so I told them to phone the Service Provider. Said they would but I had to email copy of receipt which I did. A couple of months gone by and never heard a thing and they are not responding to my emails. DO NOT RECOMMEND DACOR.

We thought we bought a quality product when we remodeled our kitchen two years ago and put in a $3000 30 inch wall oven from Dacor through their dealer Friedman’s in Knoxville. We had heard for years that their products were top notch and high-quality. I find it interesting that the oven has a self-cleaning function. However Dacor Technical advised me that if you use the self-cleaning function you will create too much heat and destroy the motherboard. Wonderful input after the fact. The oven now does not keep a correct temperature and we are advised that our oven is two years old and out of warranty and we should not have used the self clean function. Really? Why is the button even there. Do not under any circumstances purchase any Dacor product. I feel comfortable in saying Samsung will add absolutely nothing to the quality or service. The lack of customer care and concern is beyond reproach. One star rating is way too generous. How do you just walk away from your products. We used our clean function exactly once and nobody ever said it was a self destruct button.

Dacor representative has been helpful in responding to my complaint and has sent new oven racks which I greatly appreciate. I was able to send them pictures of the damaged racks. I want to clarify that the warranty that was sold to me by an upscale appliance center was NOT a Dacor extended warranty and I believe that this caused my issues to slip thru the cracks. Nothing can be done about the interior that seems to have a film of sorts on it, short of replacing, but I am grateful that Dacor customer service went out of the way to correct the problem with the racks.

In 2013 we remodel our kitchen. I need a 30" stove and Dacor seem the right fit. I had problem with the igniter burning on that stove and some metal warp as well. They replaced the stove in 2015. I smell gas every time I turn oven on. Last Thanksgiving 2019 the stove stop working. I was told the igniter had burned out and had it replaced. I had repairman come twice because of smell and end January 2020 the stove stop working again. The repairman told me that a jet burner assembly was never installed this is why I smell gas after it is turn on. ** They said they will order the part. It's back order So I contact Dacor. First they told me it's back order then give me a supplier. If it was never installed in the unit shouldn't Dacor take care of it and soon.

I have a Dacor refrigerator that cools poorly and needs servicing. Refrigerator manufacture date March 2017. When I acquired the refrigerator I signed up for the Dacor standard warranty (1 year) and the Promotional additional 2-year Dacor standard warranty advertised as 3-For-Free warranty. I contacted Dacor customer support by phone today. After an hour on hold, they said that they would have to check with their supervisor. 2 hours later I received a call back saying that its only a 2-year warranty. Their website where I registered my product (warranty.dacor.com/member) clearly indicates that my refrigerator is still under warranty. When I confronted them with this, their answer was anyone can register anything on the website and it proves nothing. In other words, registering your product offers you absolutely no protection.I provided their supervisor all documentation requested, (including proof of title of ownership of my house!), and they still repeatedly stated its only a 2 year warranty. When asked where they are getting this information, they simply said thats what we have in our system. I asked to speak to a supervisor, but they said none were available. I left a message with the supervisor, but none ever returned my call.Dacor continues to offer their 3-For Free warranty to this very day. As a busy physician, I keep good records and pay attention to detail. Dacor has been to my home previously without incident. I am extremely disappointed in what appears to be the companys blatant attempt to deny warranty coverage despite ample documentation that its still covered. I would caution folks that their 3 year for Free warranty is simply not true based on my personal experience today. I will no longer be purchasing any Dacor products because of this, and will relay my story to anyone interested in purchasing Dacor products.

We renovated our kitchen and as part of this had installed the new Dacor Modernist Fridge and Freezer columns at a VERY hefty price tag. We were going to get a subzero and changed our minds when we saw these products - the styling, design and function looked so much better than Sub-Zero, despite the higher price tag. Well, fast forward about 8 months and we dont have a functioning fridge. It stopped cooling out of nowhere. We had to throw everything away. After FINALLY getting a repair person to the house, they told me that it was because the fridge had run out of gas (freon or whatever the coolant is thats used). When asked how that happened they said they didnt know, but that they couldnt repair it as they needed a part from Dacor. A WEEK later, they finally got the part and came back to repair the fridge. 4-5 hours later it still was not repaired and they said they needed another part. Its been almost two weeks since then and the part has still not arrived. We had a BlueStar range installed when redoing the kitchen and when we had a problem with that, they overnighted the part, so that they could fix it right away. This is not the case here - the customer service has been absolutely horrendous and Ferguson Appliances (where I bought the fridge from) has been at their wits end with this (I cant say enough about how wonderful Ferguson has been to deal with). This has been a nightmare. Now the repair place wont even schedule a repair date because they dont want to lose the time again in case the part doesnt show up again... DO NOT BUY THIS FRIDGE. I should have known better not to buy a Samsung (yes, Samsung bought Dacor a few years ago and these products are glorified Samsung units).

We remodeled our kitchen in 2016. We chose Dacor 30” range. The gas oven has been a disaster. After less than a year, it wouldn’t heat. They replaced it, same problem. Replaced the igniter and valve, same problem. Now they will do nothing and say we’re on our own. Problems with hood and fridge too. Stay away from Dacor at all costs!

We purchased a Dacor gas range in 2005 for $2000. In a short time the plastic trim around the knobs cracked, and the glass in the oven door had not maintained its seal. I contacted Dacor several times and was told to take a picture and send it to them, then they could decide a course of action. The course of action was that I would pay for materials and labor. I decided not to do that, and eventually I will replace the range with another brand, never a Dacor!

As a contractor, we were fortunate enough to build our dream home which was completed in 2005. After much research and many show room visits, we purchased Dacor appliances for our kitchen. As the saying goes, if I knew then what I know now. Our biggest (note I said biggest, not only) issue is with our ESC130 oven. If you own this oven, do not, repeat, do not, use the self-cleaning mechanism. I have had this repaired once and then replaced once (along with a relay board). I seldom use this because I know when I do the lock mechanism will continue to cycle until it is replaced. This means, while I can still use my oven, I have to time when I open the door based on when the lock is cycling in the unlock position. I must also turn the oven off at the circuit breaker or listen to the continuous warning beep that the lock is cycling (as if I didnt know).After repairing this feature once, I next choose to have the mechanism replaced and Dacor offered me a discount on the parts (the oven was and still is out of warranty) at a cost of more than $500.00. This is on top of what I had already paid to have it repaired just 18 months earlier. I feared using this feature again as I didnt want a repeat performance. After cooking macaroni and cheese yesterday, I felt I really needed to clean the oven and made the mistake of using the self-cleaning feature of the oven. I dont know why I was surprised when the locking mechanism refused to stop cycling.I contacted Dacor today only to speak with the rudest customer service representative I have ever encountered, Steven. No last name. He is the only Steven who works there. He refused to listen to me, spoke over me when I did try to talk, and did not allow me to speak with anyone else. There are no supervisors available on Fridays and he could not transfer me anywhere. I left a message for someone else to call me (they did not). I called back later that afternoon and was given the name of a supervisor, Nhi. She was not available and I spoke with another customer service representative. I learned that Dacor is aware they have a problem with this locking mechanism and are trying to correct it. This got my hopes up, thinking that the company would now do the right thing and replace this mechanism at not cost to me, or at least at no cost for the parts. Not so. Even though Dacor knows there is an issue with this mechanism and they are supposedly trying to correct it, all they can offer me is a discount on parts. Really? Wow! A discount for a part that you know doesnt work properly and probably wont work properly because they are still working on the problem? I just really dont know what to say. Is this supposed to make me happy as a customer? Would prospective customers want to buy a Dacor product knowing that Dacor is more than happy to sell me a known defective product at a discounted price and they should expect the same? It is probably needless to say that I would urge all prospective Dacor owners to not waste their money on any Dacor product as they do not care about their customers. I will certainly be doing my part to warn others and hope this serves to warn others as well. Dacor has a lot to learn in terms of building even what could be called a good product and standing behind what they sell as well as becoming a customer service oriented company.

I bought a Dacor Epicure 48 range in 2003. It has never worked correctly. I read many other complaints on this same range. I had the burners replaced and I still have to light them with a match each time I turn them on. The oven temperatures were never correct. Nothing bakes properly even following their directions. It bakes very uneven. The hinges are sprung/broken (as the doors are too heavy for the lightweight hinge they use). I have had numerous service calls over the years and still not a good oven or repair. I too am very disappointed in the fact that this product is a lemon and they will not replace it.

I purchased most Dacor appliances when I built my home in 2015. Their induction cook top and dishwasher kept breaking down one by one. The first time the repair service was done well. Early 2019, their cooktop broken down again and I still have the half broken cook top for almost 4 month now. We have been emailing back and forth, firstly Dacor promised to mail me the parts, but then a different customer rep reached out saying I have to take the broken parts out and mail it back to them before they can send me the replacement parts. That means I would have to live without a cook top for a while. There is even no estimation when I will have it fixed!! Dacor dont value their customer and Im comfortable to say it is the worst product quality and service I have experienced in my lifetime. Never recommend it to anyone!!

I would never buy another Dacor product. The microwave totally crashed and now the oven will not heat. I have had contact in the past regarding repairs and they are outrageous. I plan to replace both items rather than paying unreasonable costs. Very unhappy.

If anyone else has this experience with Dacor ovens, we need to have a class action suit against Dacor! While baking Christmas cookies this week with my grandchildren, my ovens stopped working and started beeping. The error code was F3. I was able to get a technician rather quickly who diagnosed the problem as a failure of the control board which affected both ovens. The replacement part was discontinued from production in 2011. My ovens are 12 years old and cost over $4,000 at the time. What a pickle I was in a week before family coming for Christmas dinner!The technician said my only recourse was to send the control board to a refurbisher and he did not know when the board would be fixed - all for a whopping costs of over $600.00! I find it unacceptable that Dacor discontinues a control board and forces the consumer to either buy new ovens or pay the cost of a refurbished part that I hope will work. After spending thousands of dollars, how does this happen? What can be done so the consumers who purchase appliances with good intentions are protected from manufacturers that dont stand behind their products? DACOR I NEED ANSWERS!!

The glass plate in the bottom of the oven has been a disaster from day one. Anything that drops on it leaves a white mark that is impossible to remove. It finally became so discolored that I had to have it replaced; over$100 for glass and factory-trained repairman charged $285 to install, a ten-minute job. I wish someone had told me of the problems before I spent over $5,000 on a range which should be useable, not just pretty to look at which also doesnt happen when the oven is all stained. Burners are tinny and dont begin to compare with the Thermador I have in my other home. I will never purchase another Dacor product.

I have own my range for about 2 years and for the most part it is used every day. I love the simmer burner and how strong the rest of the burners are. My food always cooks well both on the stove top and in the oven... I love this range.

I purchased a DACOR Discovery IQ Range one year ago Model # DYRP36DS/NG from an online authorized DACOR retailer. Here is a synopsis of the events Ive had with the range over the past 12 months: I took delivery of the Range in January of 2016 at my home under construction. I moved into the home in April 2016 which is when the Range was fist installed. In May I began to have problems with the unit, it would shut down during preheating, then reboot itself, sometimes it would just reboot itself randomly. I called DACOR customer support who told me that I needed to download the latest software version, which I did. Shortly thereafter, the Range again would shut down during cooking and go into a reboot cycle.I called DACOR again, they sent out a local service company. In June the technician came out and upgraded and re-installed the software. The problem continued, I contacted DACOR AGAIN, got the run around, etc... Escalated the problem. DACOR then determined the problem was in the internal circuit board which they arranged to shipped to local service company. The service company came out again, replaced the internal circuit board and attempted to upgrade the eProm, which didnt work. The Range was in a constant state of rebooting itself over and over and over again. The Technician left. Said nothing more he could do. I had to shut the power off so the unit would stop rebooting itself.I called DACOR AGAIN, I got a complete run around, they refused to do anything more. I finally was able to reach the V.P. of Customer Service. After a few conversations and investigation into the issues. She determined that the unit needed a new front controller panel. The panel was shipped to the local service company. The service company came out again and replaced the front controller panel. Its now November. Over Christmas, the unit began to shut off the oven randomly during cooking cycles, for no apparent reason. Over New Years, the oven was shutting off, flashing an error code and reboot! I called DACOR last week. They refuse to help because now it is out of warranty.Ive contacted the online retailer. Ive left messages at DACOR for the Service Manager and the V.P. of Service. NO RESPONSE. So this is how DACOR deals with servicing their high end appliances, keep trying to pretend to fix the lemon appliance until the anniversary date, and then they dont have to deal with their $9,000 piece of garbage high end range any longer. The consumer gets screwed and DACOR doesnt care in the least! DO NOT BUY an appliance from DACOR.

I have a Dacor MORS130SS oven that I purchased in July of 2008. After 6 months the first membrane panel failed, one year later the second membrane failed. One year later the third membrane failed. Im on the fourth membrane and now my fine Dacor is burning things!! I can set the temp to 350 and it shows 350 on the display but the lower element never shuts off and whatever I cook gets burned. I bought this oven thinking it might be my last considering the supposed quality of Dacor. I know for sure it wont be my last oven!! I sell appliances and I never recommend Dacor ovens because of all the continued problems. Ive never used the self clean feature since being told by a Dacor tech trainer that he didnt recommend using self clean because it would cause the oven to age faster. Wonder how long it would have lasted if I did use self clean? Sure wish Dacor would contact me for a testimonial!

Previously, I submitted a complaint here and I would now like to amend it. The problem(s) that I experienced with my 8 years old Dacor 30-inch wall oven was what I described in my earlier post (July 9, 2012). But after posting here, I was contacted by a Dacor representative not once, but several follow-ups to ensure that the problem was resolved to my satisfaction. It was and Im now very impressed with Dacors customer support. To be fair, I should have contacted Dacor with my problem before blasting their product here.It has been a good oven for 8 years and given their support that Ive recently experienced, Id be more inclined to purchase Dacor products in the future as it appears theyre willing to stand behind what they sell. Im really glad this issue was resolved because I was about to throw in the towel and buy something else, but couldnt find anything else that looked near as good as my Dacor and had glowing product performance reviews.

I purchased a Dacor Black Dual Fuel Range (RSD30B) in 2001 which was installed during a kitchen remodel. We moved back into the house on 12/24/01. We hardly ever use the oven because my husband barbeques every night. In less than 5 years, a piece of the plastic front control panel fell off. In early 2008 the self cleaning function broke (error F2). I called Dacor and they referred me to a repair service. It was going to cost almost $500 to repair so, given that we use the oven so little, I decided not to spend the money on an oven that was falling apart. Now within the last two years the plastic control panel is cracked across the front and more pieces are starting to fall off. Now the clock and the timer have stopped working. I called Dacor again today and was told that the seals and hinges on the oven are probably bad, which is contributing to the problem. The customer service person was rude and unhelpful. He said it was not unusual for a ten year old oven to break. He gave me contact information for a parts dealer and two repair services. I bought this oven believing it was a high quality and I expected them to stand behind their product. What can you do to help me?

Our initial dishwasher had many problems. After several service calls, we called Dacor to identify the issue and see if there was anything they could do for us. We received a brand new dishwasher (even better than the initial one) for a nominal cost. We would like to thank Dacor for their excellent service and attention. Its not always the issue, but the resolution that makes the difference.

We purchased this oven/cooktop was installed in February 2020. I have been unhappy with the performance of the smaller oven from the beginning. It takes 20 minutes to pre-heat, a loud fan starts to run partway during the pre-heating process and then warm air starts to flow out the bottom. Plus, it is not either holding the correct temperature or not reaching it completely, nothing I cook in there is done in a appropriate amount of time. Baking a small potato takes an hour and a half at 375, brownies take almost twice the approximate baking time. My attempts to contact them have been less than satisfactory. I wrote for a second time over two weeks ago providing a copy of the invoice and have still heard nothing. I am quite disappointed with this product & company.

2017 purchased 36” range. First year- self cleaning overheated, replaced part. That was in 1 years warranty. But now: only 3 years barely: (I dont even cook much). Oven turns off by itself if I open the door. Oven does not turn off when I am done cooking. If I cook 450f pops warning of temp overheat. Called ABT service (this is where Dacor said) it cost $219 for a service guy to call dacor and to give me answer: I think it is android board. I have to buy a board. Plus per Dacor this board will not have wifi. So there is no Discovery- paid extra for extras I can not have...

Bought expensive refrigerator in Miami. And because I live in Miami 2 months in year use and tern in refrigerator only for 2 months. Every year have problems for thousands dollars. Company keep changing parts. I keep paying. Same problem every year. Big mistake to buy Dacor appliances. Regret very much and angry. People who fixing they know nothing. Only money. Very not happy. Looks like new. Today will throw on the garbage.

The Dacor gas range/ oven and wall oven were here when we bought our house in 2010. I would never buy any Dacor product again. I will have to look for a replacement for the gas cooktop range. The Dacor gas cooktop is OK except that EVERY time you turn on a burner, one or two of other igniters start clicking and wont stop until you find which one it is (not always the same) and turn it on and off. Please heed this and all the other warnings from the choir. DO NOT BUY DACOR!It is all very expensive junk. The oven temperatures fluctuate while baking. The oven range unit is out of warranty. So our home warranty AHS covered it but they kept sending out the same grubby slob who never fixed the problem but did charge us for the $75.00 service fee. They replaced the oven controller and the temperature sensor. This did not fix the problem. We have a full size oven that we cannot use! Then F1 beeping nonstop, and we have to turn power off to stop it. Now, out of the blue the downdraft fan just started extending and retracting over and over again with no way to stop it without going back to the electrical panel and flipping the breaker that it is wired into. That leaves us with no kitchen and no bathroom plugs! I hung up after 35 minutes on hold. I was just trying to find a certified technician in Bend, OR. Piss Poor Products and Very poor customer service.

Our refrigerator is 5 years old and has had a problem with icing up in the freezer area, resulting in a loud noise from the freezer fan. We originally called Dacor for service but they could not get to it for 2 weeks. An appliance repairman installed a new heater for the defroster. This only worked a short time and happened twice with a cost of over $1000. A couple of months ago, it happened again, and we were able to get a hold of ** at Dacor customer service. She knew exactly what was causing the problem. She ordered the parts and directed a factory-approved repairman to install over $800 in parts and we are confident the issue is resolved. Thank you, Dacor, for standing behind your products.

The problem started with our refrigerator unit when it was still in the first year of a 2-year warranty. We have had over 9 service calls for various problems; we had to replace the circuit board, switch and the pan twice. The warranty runs out soon. After five unanswered calls to the customer service number, we were finally able to get through; not that it made a difference. Their response was, “We apologize, but there is nothing we can do?” Sound familiar? Dacor refuses to extend the warranty even though the problems seem to be bad design, parts and customer service. Dacor says when (not if) you need another repair, well work with you. Yipee! We get to work with them some more and pay for the privilege. Dont make the same mistake we did. We will never buy a Dacor product again.

I purchased a single wall oven in 2008 and 30 days out of warranty, the oven broke. Service required two service calls to fix the door magnets. A third visit was required as the oven codes shut down the unit. The last two service calls have been with the cooling fan. Now that the fan was replaced, the relay board needs replacement, too. I have spent $650 in service alone, which is separate from the cost of parts. There’s no help from customer service; in fact, the rep was downright rude. I will never purchase this brand again and I have told anyone who will listen not to purchase.

48 in. Range - Wish I had read reviews first would NEVER have purchased Dacor. Paid almost 11,000.00 for a range so many issues they replaced it. New range came with 7 defects. It has been over a month and nothing has been done about it. Everyone keeps passing the buck and I am sitting with an high end expensive product and no help from Dacor. I am being very patient but also very frustrated at this point.

I contacted James ** at Dacor. His attitude was excellent and he resolved my problem (deteriorating dishwasher racks) beyond my expectations. He was compassionate and understanding every step of the way. James followed through on his promises in a swift and efficient manner. I would recommend Dacor and James ** to anyone. He is an asset to Dacor and should be recognized for his professionalism.

I submitted a review regarding a repair on this same refrigerator Dacor EF42BDCBSS back on 10/29/12 and 10/31/12. We now have another repair bill in the amount of $486.42 for a drain pan kit and defrost thermostat. I tried to contact Dacor by phone and email to talk about the situation, but have not received a response. I would highly recommend that you think twice about buying a Dacor brand refrigerator.

I have owned a Dacor microwave for about seven years and is so far the best microwave Ive ever owned. It works great every time, has great preset features and also has a great sophisticated look. I would recommend Dacor appliances based on my experience with this microwave.