We purchased a Dacor induction range 5 years ago which cost $5000 plus installation parts and service costs totalling $10000. Two days ago, an error code showed up indicating that the generator needs replacement. I contacted Dacor who states that the part is discontinued but that I could contact a refurbishing company (Corecentric) to send my generator to for possible repair. A service technician would have to remove the generator, I would send the part to Corecentric, then IF they can repair it, the tech needs to reinstall it. There are no service providers that Dacor referred me to that will service a refurbished part. Even if I wanted to try, I as an owner, cannot remove it myself because Dacor does not provide the service manual to do so. I spoke to Dacor multiple times about this problem and management stated that since the product is so out of warranty that they cannot offer any other repair option, compensation, or replacement even if the part is deemed unrepairable by Corecentric. When you pay $10000 for a product I expect it to last more than five years and that a reputable company would stand by their product and service. Essentially, Dacor inferred that we are out of $10000 because a part that POSSIBLY can be refurbished for $215 plus service costs, cant get serviced and Dacor takes no further responsibility. I have heard stories from appliance providers and service providers that since Dacor joined Samsung, that their customer service is poor and products have become inferior.

I have 2 single ovens side by side and have a cooktop and ventilation system - my experience with the cooktop and vent (2000) was so good that I did not hesitate to buy Dacor MorS130S ovens. They were installed in my new kitchen in September of 2012. I had my cooktop and ventilation system reinstalled. My daughter accidentally cleaned the oven without taking out the GlideRacks (which are hard to take out). We oiled them, etc., like the manual says if they are accidentally left in - they will not glide at all and now I am being told $300 each to replace excluding the cost of the service call. This is ridiculous. What kind of design is so poor that racks would get in this condition? I had Bosch ovens before and their warranty was wonderful and I, luckily, bought a Miele dishwasher which has a 10-year warranty. I would not buy Dacor again because of the warranty and because of this problem. I am beyond disappointed as I love my cooktop etc. I feel that Dacor should at least pay for part of these GlideRacks.

In 2013 we remodel our kitchen. I need a 30" stove and Dacor seem the right fit. I had problem with the igniter burning on that stove and some metal warp as well. They replaced the stove in 2015. I smell gas every time I turn oven on. Last Thanksgiving 2019 the stove stop working. I was told the igniter had burned out and had it replaced. I had repairman come twice because of smell and end January 2020 the stove stop working again. The repairman told me that a jet burner assembly was never installed this is why I smell gas after it is turn on. ** They said they will order the part. It's back order So I contact Dacor. First they told me it's back order then give me a supplier. If it was never installed in the unit shouldn't Dacor take care of it and soon.

Ive had this range for two years and am replacing the control panel for the second time. 1st time during product warranty and second time out of warranty. The range is beautiful but apparently the electronics are bad. And to add insult to injury Dacor doesnt stock replacements but has them assembled when needed. Estimated wait time for a new panel is 3 weeks; so no oven for 3 weeks and now not a lot of faith that the new board will be any better than the last one.

We bought the Dacor Wall Oven (ECS136SCH) in 2006 during a complete kitchen remodel. In 2009, the relay board was replaced twice. The first time, it was over $500 to replace. The second time, it was covered under the parts warranty when a terminal was bad. Now, I need another relay board and a new element which will cost over $700 to replace. For an oven that was originally over $3000, this is not acceptable, but what other choice do I have? The technician told me that Dacor has the worst mark up for replacement parts. I thought I had done my research and found that Dacor had a good product. I guess I was wrong.

I did a kitchen remodel in 2008 and was convinced by the sales guy at Home Expo to go w/ the Dacor over the Wolf. I bought the dual-fuel 36... Within 2 years I had serious problems. The oven, when not on Convection Roast or Con Bake, just using Bake will consistently turn itself off... Ive ruined many a meals, usually big ones: Turkey, Prime Rib(long cook time items). This was by far my most expensive investment in my kitchen and by far my biggest disappointment. I have called Dacor in the past and was told they could refer me local repair people, I was on my own for fixing it. Again, huge disappointment.

I recently complained about my Dacor dishwasher that would stop running during the cycle because of a faulty circuit board and touch pad. The repair would have cost me $500.00 to replace the entire touch pad and circuit board and the Customer Service department was not in the least helpful or concerned. After making the complaint on this site, I received an email the next day from James who was very nice and asked for the model, serial number of my dishwasher and who was the repair company I used. I emailed the information back to him and after verifying my information, he informed me that the parts would be shipped to my house at no cost and I would only have to pay for the service call! Now that was great service from a company who is trying to make good for a bad item in their appliance line. My repair person told me that Dacor is now using a different manufacturer for their dishwasher so hopefully it will be a better product.

We purchased this high end Dacor range (Dacor Renaissance ER30G) new in 2011 from the Appliance Loft here in Cincinnati. It was dropped off and installed and would not operate right out of the box. A repair was made and everything worked (unless you count the indicator lights on the knobs, they all went out after approx 14 months). This past November the oven went dead. A1 appliance came out: Determined new control board needed, ordered and installed. Thanksgiving Day, oven dead. A1 comes back, reset the High Temp Fuse. Oven dead 4 days later, A1 returns with a new HTF. Dec 22, Oven dead. As soon as The holiday is over we will call another repair shop and start looking at replacing this unreliable piece of eye candy. Open comment to Dacors design engineers, quality control engineers and management. You should be totally ashamed about this product youve designed. You are supposed to represent the best in American design and quality and this falls below that of low end appliances out of China. See you in small claims court.

Replaced a prior pro style range product with 36" all gas Dacor range and couldn't be happier. The styling is outstanding and the cooking performance is far superior to prior range. Simmer burners are amazing and convection roast is absolutely outstanding. Great product and experience!

The functions are useful and so far everything works the way it supposed to. No real complaints. Convection and baking features are really useful when it is a small thing to start an oven. Easy to operate. Everyday cleaning is easy as well.

I have a Dacor MORS130SS oven that I purchased in July of 2008. After 6 months the first membrane panel failed, one year later the second membrane failed. One year later the third membrane failed. Im on the fourth membrane and now my fine Dacor is burning things!! I can set the temp to 350 and it shows 350 on the display but the lower element never shuts off and whatever I cook gets burned. I bought this oven thinking it might be my last considering the supposed quality of Dacor. I know for sure it wont be my last oven!! I sell appliances and I never recommend Dacor ovens because of all the continued problems. Ive never used the self clean feature since being told by a Dacor tech trainer that he didnt recommend using self clean because it would cause the oven to age faster. Wonder how long it would have lasted if I did use self clean? Sure wish Dacor would contact me for a testimonial!

We purchased a Dacor wall oven to replace a GE oven that was outdated. We thought we were getting a premium appliance, but after less than a year and just before the holidays it quit with a code on the control panel we couldnt find in the owners manual. We had a serviceman out and the cost of the part and the service call was more than we paid for the oven! It now sits there, useless and a reminder to never buy Dacor anything!

I bought a 30 Dacor Double Oven (EO230SCH), 36 cooktop, warming drawer and matching convection microwave. Well over $10k. The microwave has been replaced as it died early within the first year while cooking popcorn - nearly started a fire in the kitchen... However the cooktop igniter died at 4 years and now the wall oven is on its third control board in years 3, 4 and 5. Nothing is under warranty and they want nothing to do with me now. The replacement oven controls cost ~$400 each plus installation. So after all this expense, I have invested $1,200 more in replacement parts and the cooktop needs an aim & flame to light. Total crap. Im going to replace all of this and will never go back to Dacor. I took the time to write this so that others will not waste their time with what I have to assume is the worst quality in the industry. Please dont waste your money.

We have owned our dual-fuel Dacor stove for about four years. We purchased this stove because we needed a down-vent - this is how our kitchen was already configured. We had only the Dacor or Jenn-Air stoves as choices and went with the Dacor. I have been thoroughly pleased. Everything works consistently including the self-cleaning feature. Prior to this stove, we had a Thermador which was expensive and NEVER worked consistently. One feature or another was always on the brink. The Dacor is such a relief. And good looking, too.

I, too, purchased a 30 Heritage gas range in Nov 2018. The first time I ran the cleaning cycle (2 weeks ago), the oven heating went out. After time consuming attempts to reach the warranty dept, finally got a call back. Sent the required information and was told the warranty servicer would contact me within 48 hours. After not receiving such call, I reached out via email again to Dacor and was told to contact the servicer directly. Well, I just did that, and was told they refuse to service me because DACOR IS NOT PAYING THEM! How is that for a luxury appliance company making millions off of its customers and not paying its service companies? A very clear breach of contract since my warranty is active until November 2021. I have never in my life had such an experience, with the LG, KitchenAid ranges I have owned. Never even have needed one ounce of service in their life. So now I await a response from posts on Dacor FB page and voicemail I left, hoping for service. What a colossal waste of money. Buyer beware!

Replaced main board on top of oven because of oven light turning itself off and on endlessly. Cost was near 400 dollars with service call. Now, 2 years later, F1 beeping nonstop, and we have to turn power off to stop it. Last night, the beeping started at 3 am! I would never buy another Dacor oven. The Dacor microwave has never been able to pop popcorn. Now the carousel is failing to rotate. The only thing positive about Dacor is the styling.

We did a complete kitchen remodel 2 years ago. My husband talked me into purchasing american made over the Bosch products that I preferred. This has been a horrible experience. The dishwasher does not clean. I was told to prime the water and purchase the higher end platinum packs. That did not work, then it was add lemi shine. That has not worked. The water never completely drains, ugh old water. A service tech could not tell me where the rinse aid indicator light was and insisted mine did not come with one! Microwave does not heat in an adequate time. All listed times I have to double time if not more. I was told to put a Rubbermaid container over the food product to insulate the waves... ha! Oven does not regulate heat. when I go to increase the heat during stated recipe, the screen always say 50 even though I would have it at 375. I was told it always will revert back to 350, really. I had all Kenmore appliances prior to the Dacor and never had a problem... Do not buy, I wish I hadnt. We are filing this with BBB and headed to small claims court.. This should be fun. I hope Dacor sees this.

There is not enough space to write about the problems with Dacor ovens. Just do not EVER buy any of their appliances. FOUR breakdowns, excessive cost to repair, cheaply made electronics, etc., makes me wish Id never heard of Dacor or Trial Appliances, who recommended them.

First six month, dishwasher rusted on the inside. Dacor gave us a less expensive in its place. First year, microwave was repaired five times. Microwave has a piece of wood to hold the door in place. Wall Oven, the broiler never work. Present, range oven does not work at all. We have a repairman that is trying to get parts. Present, refrigeration control panel does not work, need repair. These appliances were to be a our luxury kitchen, but turn into a nightmare. Do not buy this appliance, you are wasting your money.

After remodeling our kitchen, we purchased a professional line Dacor stand alone gas range/oven. Within a year, the heating element needed to be replaced. Subsequently, the control panel almost caught fire and needed replacement, following a second heating element. The oven is not reliable and has cost us over $600 in repairs, labor and parts. The Dacor company is not willing to recognize that this oven is a lemon, even though their rep admitted that the number of repairs seem to exceed the average number. The company refuses to pay for a tech to come in to examine why this range continue to have electrical problems. It is not working again, and the customer service rep wants us to pay out more money to have their tech diagnose the problem and pay the cost of repairs and labor, while they will cover the cost of the parts. I am done paying out more money on a defective appliance. I could have purchased two new less expensive (and more reliable) ovens by now.

This posting is in response to my original post regarding the Drain Pan heater issue in our Dacor refrigerator. My refrigerator was repaired on 10/16/2012 at no charge to me. My refrigerator is out of warranty, but Dacor stepped up and repaired the issue. The customer service I received was second to none, and I would like to thank James ** for that. Great customer service instills confidence in your product! Thank you!

I own a complete Dacor Kitchen, with many appliances. They are the highlights of my Home. Great features: fast induction cooktop with an efficient silent hood, versatile refrigerator, reliable oven, and of course the always dependable dishwasher. This is My Dacor Kitchen!

I just had an appliance repair company come out to let me know what is wrong with my Dacor Stove door, since it wont close. He said the hinges are needing to be replaced. He said that he replaces these hinges on Dacor stoves ALL THE TIME and that the company really needs to file a recall on these hinges and/or reimburse consumers who have these installed. He said these should not go bad like they do. That this is poor manufacturing on Dacors part and they are not being held accountable. I agree 100%. It is going to cost me with labor and parts almost $ 400.00 to replace these hinges that should not go bad with the age of the stove. Thanks.

I was a bit anxious when I purchased my Dacor range because I really didn’t know how it would perform. A year later and I couldn’t be happier. I love my Dacor 30” range. It has been one of the best purchases ever.

The enamel on the bottom of the top oven has blistered and the metal beneath is exposed. If the oven is heated, there is a chemical smell. This is such a dangerous situation that the ovens (double) are being removed as I write and will be replaced with a different and more reliable brand.

We remodeled our kitchen in 2006. I spent a fortune on a Dacor dual fuel gas cooktop with electric oven/convection oven. My Dacor problems seem so normal I mostly deal with it. My 2 biggest complaints are the glass oven door is not airtight, it is darkened between glass, very hard to monitor my baking. And the temp gauge has always been off by 15-25 degrees. I use an in oven temp gauge, which has been calibrated so I know it works. If anyone is planning on a Dacor, you will get the best looking range. It just wont work.

I wish we had seen these reviews before we spent 6k on an oven and cooktop. Ordered cooktop and oven in November. Custom color over to match cabinets, still have not received oven (were at the 8 week maximum wait time already). Cooktop appeared fine when we received, but when we went to install, noticed something rattling inside. Looking through vent, noticed several broken interior pieces moving around. Contacted Dacor 3 weeks ago for a replacement or repair, and still nothing. They made us go through dealer, and last week told dealer we refused service. Ridiculous! Now they are telling dealer they cant find a servicer nearby. Am considering declining payment through credit card company for their lack of follow through and service, and let them come get their unit.

DCT305SNGH - I have owned this stove for about 3 years already. From the very beginning it has been trouble. The lights that turn on when a burner is on broke immediately. The place where the gas comes out and ignites is black and hard to clean. The grates are rusty, the finish has come off. The indicator knobs dont reflect what is happening in other words if it is on the lowest setting you dont have any indicator marking. It is hard to clean and scratches very easily. I have had the service person out about 5 times until they decided to send me many new parts. These arent any better. It is just a bad product. Basically the warranty is useless if you keep calling for the same issue. They say, This is the last time we will fix this issue. Sadly I always heard this was a great company and I waited 7 years to save up for this stove and boom rotten appliance.

I purchased a Dacor Double Oven 5 years ago. It is a beautiful design, but unfortunately a piece of junk. Over the 5 years I have had the oven, I have had service technicians repair the oven on 7 different occasions. Unfortunately, my oven is not out of warranty and has failed once again. Today was my 8th attempt at service and the service technician could not get the oven working. I have called Dacor, pleading with them to stand behind their product and to replace this useless piece of equipment. I continue to get L22 error codes, and the main circuit board had been replaced twice. After persistently calling Dacor’s customer service, they finally said they would sell me a new oven at a discounted price to the tune of $4800 plus tax, shipping and installation. I ask myself, why would I want to buy another piece of junk? If Dacor wont stand behind their products, perhaps someone should initiate a class action suit against them.

Wish Id known Dacor issues when buying my oven. (Primarily for style - yes, assumed it would function as stated; high end brand). Thank goodness I DID NOT BUY other Dacor appliances. My 30-inch Dacor oven/cooktop burners work but finish started coming off quickly. Above range microwave handle broke within a year. MAIN PROBLEM: OVEN DOOR either wasnt properly installed because it doesnt close flush with unit or its hinges have loosened over the years. Although oven eventually heats, it takes forever. After examining door hinges closely, looks like oven has become unhinged - as have I. No loose parts seen. Recommendations? Other than STEER CLEAR OF DACOR.

Purchased a Dacor freezer. Freezer does not come with outer panel. Understandably, because you can choose to put your own custom panel on or order one from Dacor. Found out Dacor was bought by Samsung, a few years ago. So I decided to order a Stainless steel door from Dacor. One of Dacors reps suggested I order from J@J international. I placed order and two days later they called back saying they cannot ship door to me UPS nor FedEx will ship it. They refunded my money, so I reordered from someone else. Got ss panel toe kick and handle. Opened box only to find out no hardware, brackets ss trim for sides screws and so forth. I assumed mounting hardware would be with door. So began the part search for parts. Come to find out Samsung changed Dacors part #s. Vendors who sell the parts could not come up with parts or told me not available. Reliable parts agent told me this. I was told they should have come with freezer. Meanwhile called back Dacor to someone who specializes in dealing with these issues. She took over 45 minutes of my time giving me the impression she was gonna resolve the issue. She finally said we have the parts and inferred that I must have not talked to reliable parts. I assured her I did. She continued to refute what I told her. I have been right at two months trying to get freezer door installed. I called an Appliance dealer in Salisbury Md. to get assistance. He told me when Samsung bought Dacor he dropped line. I now see why. It has been the worst experience I have had with a company that has absolutely done nothing but appear to be concerned and say they are sorry but do nothing. It looks like it will be another 750.00 to get a couple little trims and brackets and a few screws. If I had it to do over I would never have gone down this road. This has been a two month old nightmare that is still going on. Best advice I can give is steer clear of Dacor/Samsung. Was going to buy matching column refrigerator. Not now.

I purchased a DACOR Discovery IQ Range one year ago Model # DYRP36DS/NG from an online authorized DACOR retailer. Here is a synopsis of the events Ive had with the range over the past 12 months: I took delivery of the Range in January of 2016 at my home under construction. I moved into the home in April 2016 which is when the Range was fist installed. In May I began to have problems with the unit, it would shut down during preheating, then reboot itself, sometimes it would just reboot itself randomly. I called DACOR customer support who told me that I needed to download the latest software version, which I did. Shortly thereafter, the Range again would shut down during cooking and go into a reboot cycle.I called DACOR again, they sent out a local service company. In June the technician came out and upgraded and re-installed the software. The problem continued, I contacted DACOR AGAIN, got the run around, etc... Escalated the problem. DACOR then determined the problem was in the internal circuit board which they arranged to shipped to local service company. The service company came out again, replaced the internal circuit board and attempted to upgrade the eProm, which didnt work. The Range was in a constant state of rebooting itself over and over and over again. The Technician left. Said nothing more he could do. I had to shut the power off so the unit would stop rebooting itself.I called DACOR AGAIN, I got a complete run around, they refused to do anything more. I finally was able to reach the V.P. of Customer Service. After a few conversations and investigation into the issues. She determined that the unit needed a new front controller panel. The panel was shipped to the local service company. The service company came out again and replaced the front controller panel. Its now November. Over Christmas, the unit began to shut off the oven randomly during cooking cycles, for no apparent reason. Over New Years, the oven was shutting off, flashing an error code and reboot! I called DACOR last week. They refuse to help because now it is out of warranty.Ive contacted the online retailer. Ive left messages at DACOR for the Service Manager and the V.P. of Service. NO RESPONSE. So this is how DACOR deals with servicing their high end appliances, keep trying to pretend to fix the lemon appliance until the anniversary date, and then they dont have to deal with their $9,000 piece of garbage high end range any longer. The consumer gets screwed and DACOR doesnt care in the least! DO NOT BUY an appliance from DACOR.

Front bevel of my first rsd30 range purchased in California in 1999 cracked within nine months. Dacor said it was a defect in the design and would fix it for free. I sold the house in 2001 but the range was still not fixed. I moved to Nevada and bought a new rsd30 range and same thing happened within six months. It took a year to get it fixed at their expense. This bevel also cracked again for the second time in March 2011. Their response to this was to offer me a new bevel for $180 and I would have to pay for the installation. I declined the offer. The bevel is still cracked at this time. At the same time, I bought a PMOR30 over the range microwave and the front handle broke at least four times. And finally, the whole thing broke down and was not repairable. In Aug. 2008, I contacted Dacor and they agreed to replace it with a new DMT2420 over the counter microwave for half the price ($390). Last week, this one blew up on me. Sparks were coming out through the side and a big hole in the removable shield and burn damage to the wall of the unit. I do not believe this unit is repairable. I contacted Michael at Dacor. He apologized and said that theres nothing they can do about it as it is out of warranty but they will look into it. What I want at this point is my money back that I paid for ($390) and for them to pick up the unit and get it out of my house. I will never buy another Dacor product again.

We remodeled our kitchen in 2002 and chose the Dacor 36 dual-fuel range. I was preparing a pork roast for a dinner party with the oven on Bake. The roast was just not coming up to temperature, though the display indicated that the oven was at the temperature I set. I wound up slicing the roast and cooking it on the griddle; my hungry guests were getting restless. Then I tracked the oven heat for an entire day with an oven thermometer. The oven would come up to temperature and then cool off. I sent these numbers to Dacor and asked customer service for an explanation. Believe it or not, the conversation was--Dacor: The temperature is going down because the fan is coming on. Youre not supposed to use the Bake setting, but only the Convection Bake or Pure Convection. Me: Why is the Bake button there, then? Dacor: Were taking it out in the next production run. (This hasnt happened. My sister-in-law bought a Dacor last year before I could warn her and the button is still there.) Also, after using the self-clean one time, I noticed a crack on the inside of the oven door, starting in the corner of the window. The inside of the window is now permanently spotted with baked-on grease. Now my oven does not work at all. The repairman says that the circuit board needs to be replaced, and if Im lucky, it will work for a couple of years. The repair will cost around $700 including labor. The repairman told me that some repairmen in our area will not even work on Dacors because there are so many problems. Im considering replacing the stove... a very expensive mistake. Beware of Dacor products.

I called the customer service number regarding my double oven. It just randomly beeps and now turns off. No error code displayed. It has done this on and off since 2003. Now it is happening all the time. I called customer service and they seemed to act like it is my fault and I need a new touch pad. I inquired and this is a recurring problem with this model. I could not get a straight answer from the person I was talking to. He just told me that if the repairman says I need a new touch pad, then I need to get one. Well I have been doing some research and this is a problem that seems to be haunting more people than I. We own a Dacor gas cooktop that has had to have a switch repaired. We own a microwave that has had two new circuit boards and now a beeping oven that gives no error code and turns off by itself. My advice, do not buy Dacor appliances.

We had our whole kitchen renovated and purchased Dacor appliances through Caplans Appliances. We purchased the appliances in the summer of 2019 and they were shipped shortly after. Since our kitchen was still under construction the appliances sat in our home. They were installed the second week of November. Two months ago, I woke up to a sucking noise from the dishwasher. The dishwasher had a code of LC. We removed the custom kick plate to realize that there was water damage. Dacor has been contacted on numerous occasions regarding this and the dishwasher continues to leak. We have had 5 service calls to house and the problem persists. The seal has been replaced twice in a 2 week period. The repair company HARGTA gives us a window and does not show up at that time causing me to sit around all day waiting for them and then some days having to cancel work. Dacor customer service continues to say the Regional Tech Manager will be the one to provide the resolution and we have not heard from them yet. The reviews on here clearly indicate that the dishwasher leaks. We are risking damaging our floors which were put in at the same of our renovation. Looking for a resolution ASAP. To those considering Dacor appliances do your research.

I have a induction Dacor stovetop. Its stopped working and blinks an error code. Called customer service who didnt know what the code meant. I was told my model was 2015 which the rep said was old. It was installed in 2017. All they would offer was cheaper replacement parts if I paid for someone to come and figure out what the problem was and install the parts. I was told the replacement parts were not cheap though. I was told that because were the second owner of the house they couldnt fix it under warranty (even though it should be covered under warranty) because they couldnt say how it was used before (commercially or residentially). Give me a break!It gives me almost no confidence in getting this thing fixed. Warranty is a joke and customer service is terrible. So far I had to leave a voicemail for the reps next level who will call me back after the weekend. Im waiting to see what (if anything) they will do but from the first rep. I dont have a lot of confidence in their products.

Years ago I purchased the Dacor Double Oven over a Thermador because the Thermador had a ridiculously long pre-heat time. The Dacor has performed reasonably well as a oven particularly in convection-bake mode. But over time, components started failing and repair parts were hard to find, unavailable or ridiculously overpriced. I am an an engineer with DIY skills honed from years working with high tech food manufacturing equipment and controls including ovens. In recent years, I have needed to replace a relay board, the main control board, hinges two times, and most recently the hinge receptacles. I have also replaced an inner panel on a door assembly. Just think what such repairs would have cost for an average consumer. I understand the parts can fail, but Dacor has shown little regard for consumers in my opinion. They have done very little to maintain an inventory of repair parts. Basically their message is that the part is now obsolete and unavailable. Thats some answer when the price of a new double oven is multiple thousands. Recently, the hinges on my upper oven failed again. As they failed, their failure caused increased wear on the hinge receptacles. Soon the receptacles failed as well. I was able to find hinges at a ridiculously high price but the receptacles were unavailable anywhere. I contacted a several parts suppliers who told me that they had no idea when the parts would be available. Moreover at least two of the suppliers mentioned that they had a backlog of orders for the receptacles - one had a backlog of over thirty. Yikes!. At that point I contacted Dacor customer service and asked what could I do to get the part. Answer: The part is unavailable and we have no estimate on when it will be available. I tried to escalate my request and got nowhere. Finally after many hours of online searching, I found one set of the hinge receptacles at a price 4X last years price. Lastly as I replaced the receptacles today, I realized that the mounting screws only hold one portion of the U shaped mount. If the screws were longer, the receptacle would be less prone to twisting and wear. Be aware that Dacor was sold to Samsung a few years back. Based on my experience, I could never recommend Dacor. Caveat Emptor!

When I bought my house, the previous owners told me that theyd been having problems with the Dacor oven. They had purchased a replacement burner and prepaid the Dacor authorized service technician to install it for us. We have worked for three years now to get Dacors authorized service representative to install the part for which he has already been paid, and have been using a toaster oven to prepare meals for a family of four the entire time. The oven will heat to 135 degrees, then either shut off completely or immediately switch to broiling mode and burn whatever is inside it. When I called Dacor to see if they could help with the service issue since the technician was authorized by them, they told me it was my problem, not theirs. Although if the product they manufactured wasnt faulty in the first place, it wouldnt be anyones problem!

This is a follow-up comment from my last post dated June 21st 2011. My local appliance company, where I purchased this oven, seems to have helped with their recent fix. I was able to bake a white cake, following the box directions, that was not burned on one side and raw on the other; it was okay. With fall arriving, I will be back in my kitchen and will be using my oven. I will keep you posted. I still would not recommend this oven to anyone, and will not purchase any future Dacor products.

I have a Dacor cooktop, single wall oven, warming drawer, and dishwasher that I installed in my kitchen in 1992. That is 20 years ago. I have never had a problem or needed a repair on any of the appliances. They have worked perfectly. I hate reading about all the problems people are having with their Dacor appliances as I am about to do a major kitchen remodel and plan to go with Dacor again.

We remodeled our kitchen in the fall of 2009 and decided to purchase what we thought were higher end Dacor appliances (stove top, oven and microwave). Well, what a mistake that turned out to be. Considering the price we paid for the appliances, you would not expect problems from all 3. Perhaps a problem with 1 appliance, but problems with all 3 suggest a real quality problem. My first indication should have been when I called and asked how to change the green LED on the microwave to blue to match the nice blue LEDs on the oven mounted right below. I was told that someone else makes the microwave and Dacor just puts their name, and that I should just turn off the LED on the microwave. I dont know if that is true, but that is what I was told.Now when using the microwave/convection feature, the oven makes a noise (sounds like a fan motor) for the first 3-5 minutes then eventually quiets down. A daily reminder of the mistake we made purchasing Dacor. Then those nice blue LEDs on the oven started failing making it impossible to read the clock, timer or temp. Luckily, the oven still works; you just cannot read the LED any longer. This is a constant reminder of the mistake we made buying Dacor as we see the LED every time we walk into the kitchen.Finally, we have the solid surface electric cooktop. Although it works fine, the black paint on the metal trim around the stove top is wearing off. Now, we have some shiny metal and some black trim. This is just an annoyance and honestly, we probably would not have even complained about it. However, with the other problems we have had with Dacor, it just adds to our overall disappointment with Dacor. If I knew then what I know now, I would be a lot happier because I would have GE appliances and not these overpriced low quality Dacor appliances.

We moved in our new home in June 2019. We had purchased 2 Dacor dishwashers, 2 ovens, a gas cooktop and a microwave. All the appliances are beautiful. That said, both of our dishwashers leaked so bad we had to stop using them as they were damaging our wood cabinets and floor. Dacor sent service persons out after multiple calls and replaced the seals, but they still leaked. Our cabinet company that sold the Dacor appliances stepped up and replaced them both with Bosch dishwashers.Our Dacor Refrigerator went out in mid February and will not cool anymore. After 2 hours on the phone with a Dacor representative, we finally were able to schedule a service person to come out a week later (Dacor has very few support companies so dont plan on anything happening too soon when there is a problem). Was not able to repair the fridge and said it could be another two weeks to get the part and return. That said our service person is a great guy and cares, but has to rely and wait on Dacor for responses and parts.Our ovens take twice as long to cook as any other oven we have ever had. We are asking them to look into that as well. Overall, very disappointed. We understand having problems, but expect Dacor customer service would be much better and support their own field service persons and clients or at least act like they care. Not looking forward to calling them back to see why we need to be without a fridge for 3-4 weeks total....

As a contractor, we were fortunate enough to build our dream home which was completed in 2005. After much research and many show room visits, we purchased Dacor appliances for our kitchen. As the saying goes, if I knew then what I know now. Our biggest (note I said biggest, not only) issue is with our ESC130 oven. If you own this oven, do not, repeat, do not, use the self-cleaning mechanism. I have had this repaired once and then replaced once (along with a relay board). I seldom use this because I know when I do the lock mechanism will continue to cycle until it is replaced. This means, while I can still use my oven, I have to time when I open the door based on when the lock is cycling in the unlock position. I must also turn the oven off at the circuit breaker or listen to the continuous warning beep that the lock is cycling (as if I didnt know).After repairing this feature once, I next choose to have the mechanism replaced and Dacor offered me a discount on the parts (the oven was and still is out of warranty) at a cost of more than $500.00. This is on top of what I had already paid to have it repaired just 18 months earlier. I feared using this feature again as I didnt want a repeat performance. After cooking macaroni and cheese yesterday, I felt I really needed to clean the oven and made the mistake of using the self-cleaning feature of the oven. I dont know why I was surprised when the locking mechanism refused to stop cycling.I contacted Dacor today only to speak with the rudest customer service representative I have ever encountered, Steven. No last name. He is the only Steven who works there. He refused to listen to me, spoke over me when I did try to talk, and did not allow me to speak with anyone else. There are no supervisors available on Fridays and he could not transfer me anywhere. I left a message for someone else to call me (they did not). I called back later that afternoon and was given the name of a supervisor, Nhi. She was not available and I spoke with another customer service representative. I learned that Dacor is aware they have a problem with this locking mechanism and are trying to correct it. This got my hopes up, thinking that the company would now do the right thing and replace this mechanism at not cost to me, or at least at no cost for the parts. Not so. Even though Dacor knows there is an issue with this mechanism and they are supposedly trying to correct it, all they can offer me is a discount on parts. Really? Wow! A discount for a part that you know doesnt work properly and probably wont work properly because they are still working on the problem? I just really dont know what to say. Is this supposed to make me happy as a customer? Would prospective customers want to buy a Dacor product knowing that Dacor is more than happy to sell me a known defective product at a discounted price and they should expect the same? It is probably needless to say that I would urge all prospective Dacor owners to not waste their money on any Dacor product as they do not care about their customers. I will certainly be doing my part to warn others and hope this serves to warn others as well. Dacor has a lot to learn in terms of building even what could be called a good product and standing behind what they sell as well as becoming a customer service oriented company.

We chose DACOR (8-burner double oven top of the line ERD60S06CH/LP) in 2006, new construction because we disliked the signature blue interior of another luxury brand. Last October I detected a gas leak from one of the burners. The authorized repair company was contacted, and the entire unit - all 8 burners and both ovens were out of commission while we waited for the replacement part. Six weeks later the repair guy returned with the wrong part. We had to wait an additional month for the repair guy to return. Apparently, not important that people might want to cook and bake before the Holidays! After the new valve was replaced the oven light began to turn on when any of the gas valves on the defective side was turned on. I write this review 8 months into the problem. I can fix for $700 by ordering a new control panel. I wish I had read these reviews earlier. I overheard the tech say that there was electrical interference and that the wires need to be insulated to stop the oven light from turning on and off. I am so FED up with both the Dacor California head office not caring and the horrible authorized service company. I will take this unit apart myself and fix it. DACOR IS GARBAGE. Go with Sub-Zero, Miele and forget this Brand. DACOR: Dont Accept Crap Or Rubbish! Made in America? Shame on you. No problems with 4 Sub-Zero fridges, or 4 Miele dishwasher the same age.

I owned a 36 Dual Fuel Epicure range that required at least an annual repair for the same thing. The control pad (the pad with the buttons that controls the oven and light) would fry. This would cause the oven light to come on and off like a strobe light. Luckily, I purchased an extended warranty from the vendor, as each time this was replaced it was $750+ to repair. When I complained to Dacor on their support line, the representative actually told me that I was running the oven too hot!About 6 months ago, I sold the house and left the very expensive range behind. It was problematic from day one. Other repairs included replacing the ignitors. After a year of use, the insulation on the door came loose and was hanging in plain view through the window on the door. Every repairman that came to service the range said the same thing.... that they repair a lot of Dacors. When it worked, it was a great range. If you do buy a Dacor, do yourself a favor, buy the extended warranty. You will need it and it will pay for itself.

I have own my range for about 2 years and for the most part it is used every day. I love the simmer burner and how strong the rest of the burners are. My food always cooks well both on the stove top and in the oven... I love this range.

I have owned a Dacor dual fuel 6-burner range for several years. I paid approximately $5,000 for the product. It has proven to be totally unsatisfactory. The gas burners click and make noise whenever you try to turn the burners down to a low temperature. The cook top is very hard to clean. The range is a constant problem. It smells bad, does not heat up promptly, and the broiler feature is always a problem. A gas oven is supposed to heat to and keep a constant temperature - the Dacor does not. The broiler will not cook food evenly or well. The door to the oven will not close properly and is constantly partially open. The hinges do not seem to work properly.Most importantly, I have tried on many occasions to get Dacor to do something about the defective product. They have been totally non-responsive. When I did finally get somebody to come and look at it, they spent about 2 hours cleaning it, accused me of using the wrong cleaner on the cooktop, and presented me with a bill for $800. I asked if they would just give me my money back and take the defective product with them. DONT BUY DACOR.

I purchased a 30 Dacor dual fuel range and matching hood in 2004. I paid $4009 for the range and $948 for the hood. The range and hood have been nothing but problems. I wrote to Dacor in April 2009 detailing the problems with the range with service history dating back to 2006. Problems include overheating when cleaning which is a safety risk, replacement of cooling fan, ignitor assay, part # 92309 membrane, and replacement of relay board in 2007, 2009 and again December of 2011. I attempted to purchase a Dacor extended service agreement in January 2009 but was declined due to the ranges past history and its age. I recently found this site which indicates that other consumers have had similar problems with Dacor products. Dacor has lost me as a customer as I will never buy another Dacor product! I have been disappointed and frustrated with their lack of response and support. I finally purchased a GE service contract which has helped absorb some of the cost of ongoing repairs. The overhead lighting has long since gone out in the hood. I was told the hood needs to be disassembled to replace the lights. Dacor should step up and support its products. When most people put out $4000 for a range, they expect to get a quality product that will last 15-20 years. With Dacor, this has definitely not been the case!

Dacor 48 dual fuel range - Only 3 years ago, we purchased a Dacor range that is beautiful and worked great for 2 1/2 years. During the last six months, I had the led lights go out on some of my cooktop knobs and my oven has started not baking evenly, much as described in a previous post (half of your cookies can be burnt and the other half dough). A serviceman has been out twice and I have been made to feel that basically, I dont know how to use this oven or dont know how to cook. Funny that has only been in the last 6 months. I cooked great with the range for 2 1/2 years and have 20 years of cooking experience, but obviously, I dont know what Im talking about. To replace a led light bulb, I had to purchase a $300 control board part (that Dacor did discount) plus a $100 labor. It ended up being a $250 light bulb fix that has exploded to a potentially additional $600 problem. When taking off the range lid to replace the lights, I am now told that 3-4 burners have to be completely replaced and this again is my fault somehow because the metals fuse together and that is known by Dacor to happen, but my service tech said its because I dont clean my range well enough. This still makes no sense. And to fix the oven problem, it might be the control board? Lets throw my money at it and see? All guessing, the serviceman, Dacor, etc.! So now Im stuck with a parts bill of over $1,000 (Dacor did discount this to about $300) plus $200+ in labor, another guess. This just seems ridiculous to change a light bulb and guess at an oven fix for a 3-year old range that cost as much as a car! Im so irate over the whole issue! What a mistake Dacor was.

Updated on 05/12/2020: I wrote a review of our Dacor kitchen and gave the company a review of 2 stars because the cooktop, ovens, and hood blower all have failed at some point. The real issue is that the company doesnt support products after sale to quote them they do their best... The other problem is this site, it allows companies to claim they are or have resolved issues, without a response or comment from the customer about what the Companies Resolution entailed. Sending me an e-mail that says sorry the thousands of dollars you invested in our products only bought you up to 7 years of replacement parts, isnt what most people would call a Resolution. After months of working with the retailer and Dacor the e-mail below is what they consider a Resolution:Subject: Dacor customer service **Hello Mr. **, We would first like to thank you for staying a Dacor customer for as long as you have and would like to apologized for the inconvenience. As a manufacture we are constantly innovating products and at some point parts and units do become obsolete. Dacor does provide parts for as long as we possibly can. Once the appliance becomes obsolete we are only required to hold parts for up to 7 years. We again thank you for being a Dacor customer. Be safe during this pandemic. Have a great day. DENISE ** | Customer Service RepresentativeO: (833) 353-5483 x** F: (626) 403-3130Original Review: We built a new home in 2003 and purchased Dacor Preference appliances. Including a 6 burner cooktop, double 30 inch wall ovens, warming drawer, a microwave, and large hood with a remote blower. All the appliances are stainless. We enjoy home cooked meals and prepared at least one meal a day. Our kitchen is a work place not a show place. So these are my feelings after 16 years of use.The Cooktop has plastic knobs and a rubber gasket under each burner and piezo electric igniters. All of these items have failed over the years. I replaced the burners some years ago because when the gasket fails the burners sputter and liquid spills leak into the bottom of the cooktop. Replacement burners fixed the problem for a while but the burner design makes this a point of failure. Additionally, the burners were expensive so were back to sputtering burners and disassembly for cleaning. One of the plastic rings under the flame control knobs broke, weve ordered a new ring ($26) a couple of months ago but Dacor cant give us an estimated delivery date. For the past few years the Piezo electric starters only light half the burners, (they spark but the burners dont light) not a big deal but these are high end appliances, using a match to light the burners is definitely 1950s.The 30 inch double ovens are a great size for bakers like us. The Convection feature is great. However, the first time we ran the self cleaning cycle on the upper oven the door handle on the bottom oven bubbled and melted. The real issue with ovens today, is that Dacor has stopped making replacement parts including the electric heating elements. So even though we spent nearly $3,200 for these ovens, Dacor no longer supports them.The Microwave never worked correctly and we replaced it almost immediately. At that time Dacor used relabeled Sharp microwaves. Finally, Im not a fan of cooking smells in the house. So, we purchased 48 inch hood with a 10 inch inline blower. This week it failed. The motor hums but the fan doesnt turn. So replacement parts? Nope. If you decide to purchase Dacor be aware that the company doesnt provide support for their products in the long term.

Dacor 27 electric double oven unreliability. Almost from first use the Dacor electric double oven has been plagued with problems including but not limited to door not locking when self cleaning, not self cleaning, door not unlocking upon completion of self cleaning, and filter issues. Since purchased in 2013 the top oven has been used between 75 and 100 times; the bottom oven less than 25 times. Yesterday the oven died. First error message U43 relay board. Second U60 cooling fan. Worse when the control board responsive/froze circuit breakers were needed to turn oven off.Repair estimate is $1600 plus tax. I intend to replace the overpriced and unreliable Dacor with a Kitchen Aide at approximately 13 the price based on customer and Consumer Reports reviews plus a new one year guarantee. I do not recommend the Dacor double oven if you are a serious cook and/or frequent user. Brand name and styling are less important than product reliability and useful life especially when you can purchase the former for two-thirds less money.

Two years ago, we redid our total kitchen at considerable expense. All of the appliances we replaced were made by Dacor. They included: 1) a 36-inch refrigerator model EF 36/wf; 2) a dual wall oven, model EO230SCH; 3) a gas cook top, Model RGC304; 4) a dishwasher, ModelEDWH24S and; 5) a range hood, ModelEH3012SCH. The problems started within a two months of installation. The refrigerator stopped running due to a relay failure and a compressor problem; both were replaced by Dacor at no cost to us. It was inconvenient but not costly. A short time later, the lower wall oven stopped working as well as the lights in both ovens. This required the replacement of the main control panel (control circuit board). Dacor paid to have it repaired. The clock does not keep accurate time and gains about an hour a day. We decided to leave it well enough alone and did not have it fixed. After the one-year warranty expired, the lower oven quit again. This time, it had to be removed from the wall and an exhaust fan in the lower oven was defective and had to be replaced. Dacor’s initial response was it was out of warranty, so it was up to me to cover repairs. They eventually agreed to supply the part (about $90) but we had to spend several hundred dollars to install. Now, the lower oven takes an extremely long time to heat up, and again we decided to leave it well enough alone. Recently, there was a loud flash in the vent hood; one of the bulbs apparently burned out. My wife tried to turn off the lights in the hood but the light switch apparently blew when the light went and could not turn them off. After a couple of burned fingers and a melted bulb removal tool, I managed to get the other bulb out. A call to Dacor got the usual out of warranty response. I called the local Dacor authorized service rep. He looked at the problem ($95) and said he would have to call Dacor. After he talked to Dacor, they called me and said they would send a replacement control board but would not pay for the service calls. The service company said the next service call would be $195. One light bulb burned out: cost $290. I suspect that every hood unit that Dacor made with this control board is also defective. We have had to replace the halogen bulbs with great regularity. We have halogen bulbs in our boat that have lasted at least 15 years. There was another complaint on this board that had a similar problem with the vent hood. He decided to fix it himself. He is an Electrical Engineer his comments are worth reading and speak to the inadequate design of this unit. It is a shame that the Dacor appliances appear to be near the bottom in terms of reliability. Consumer Reports that their gas cook tops appear to be the least reliable. It looks like I have something to look forward to. Needless to say, I cannot recommend Dacor to anyone. In fact, I would recommend that they not purchase any Dacor product that does not have a full multi-year warranty.

I bought a Dacor dual-fuel range in 2002 for my new house. Within 18 months, the control panel on the front had shorted, causing the stove to emit a continuous beeping. I got this repaired, and was advised that I should not use liquid cleaners on the stove! Two years later, the same thing happened again. Finally, about 4 years ago, another fault developed in the 3rd control panel, the circuit controlling the oven lights will not respond to touch, and the oven lights switch on and off continuously. Not prepared to pay for yet another control panel replacement, I switched off the power to the stove at the main fuse box. I have continued to use the gas cooktop only, lighting it with an ignition wand. The Dacor stove is only part-functional due to what is obviously a severe design fault in the front touch control panel, which causes the panel to short. I switch on the power to the unit twice a year to use the oven at Thanksgiving and Christmas for large roasts. This stove was a very expensive mistake. Luckily, I have a second (Wolf) oven in my kitchen, which I use instead for everyday cooking.

We purchased a complete kitchen with Dacor Modernist stainless steel look. It has been a complete disaster since install day. The first week the Dishwasher flooded my kitchen causing water damage to my brand new kitchen cabinets. There was a seal issue. My ice machine has been worked on 6 or more times. They have replace every part in it and still doesnt make ice or if it does it freezes in to one big block of ice. My microwave combo oven just broke again today with same error code as last time. They had to replace both motherboard in the oven and microwave. Tomorrow they are coming because my dishwasher never completes a cycle. It shuts off at 16 min left. I have been asking for replacement units or better yet take it all back...I would not recommend Dacor espcially how much we paid... over 30,000.

I have owned a Dacor Convection microwave for a few years and is so far the best Ive ever owned. It works great every time, has great preset features and also has a great stainless steel look. Great Product.

We purchased our home brand new in August 2006. The house was built and the appliances installed (but never used) in 2003. One of the things that sold us on the house was the kitchen being comprised of all high-end Dacor appliances (double convection oven, cooktop, dishwasher, and built-in microwave). Our excitement quickly turned to frustration. The first problems began with the dishwasher, which after several attempts at repair (circuit board) was begrudgingly replaced by Dacor, with “begrudgingly” being the key word. I have always found Dacor customer service to be rude and dismissive - with the only way that I ever received a satisfactory outcome, being via threats of contacting the BBB and Missouri Attorney General.About a year after receiving the replacement dishwasher, the internal racks began rusting badly. Once again, I called customer service who originally wanted to sell me new racks at a discount. Only after another persistent round of explaining that high-end dishwasher racks should be made from a material that doesnt rust, complaining and threatening, did I receive new racks free of charge. I was also informed that they had changed rack manufacturers and that would eliminate the rusting problem. Wrong. It has now been another couple of years, and the new racks are rusted worse than the previous ones. That is just the dishwasher.Our Dacor microwave display began slowly losing its LED display about 2 years ago. Lately, the microwave interior lining is beginning to disintegrate and rust through. One of the burners on our gas cooktop makes a constant popping noise when lit. The top half of our double convection oven no longer heats beyond 250 degrees. I realize that our appliances are now significantly beyond their warranty period, so I am no longer even attempting a resolution through Dacor. I will most likely ride these appliances into their graves and replace them with another brand. I am writing this mainly to alert others about my experiences with what I believe to be Dacors total lack of quality at a premium price. In my opinion, Dacor is all style and no substance.

We purchased this oven February 2009. On 6/7/11, we had to replace the touch pad assembly. On 12/16/13, we again had to replace the touch pad assembly with a cost of repair to this point of over $900.00. The over cost $2,395.00 when purchased. On 3/16/14, while on convection/bake the oven switched over to broil. On 3/20/14, a repairman came to the house. The condition did not replicate but the repairman, in conversation with Dacor, determined that the fix, if this should happen again, would require the replacement of the relay board and ERC control at a cost of $700.00. On 3/27/14, while on convection/bake, the oven switched over to broil. I called Dacor and was forced to leave a message.

We purchased a under counter Dacor oven. The timer started given problems, tried contacting Dacor. The rude customer service advisor first talked to me like a police interrogation, then said sorry cant help. A joke of company with cheaply designed products. Never again.

Don’t purchase Dacor appliance - it’s been worst purchase experience ever and I am extremely disappointed. After six months since I purchased the Dacor built-in refrigerator, Dacor couldn’t even ship the proper installation parts and my refrigerator is still not working. Problems:1. Their high end $11K Dacor built-in refrigerator cannot even be installed. Wasted five months communicating with both Dacor and the retailer AppliancesConnection. After five months they were still able to ship the proper missing installation parts. Over the past five months, I talked to six different team members in Dacor customer support team, escalated to customer support lead and also talked to their regional technical manager, none of them is able to solve my problem and ship the right installation parts.a) Their process is extremely messy. Their customer support team had no idea about installation requirement of the refrigerator. And the request from their customer support team is declined by their internal Parts department again and again, only to find out installation parts should’ve shipped by the retailer. This is extremely confusing now and no one in the team seems to understand the right process.b) After Dacor acquired by Samsung, their manufacturing process is very messy and parts are extremely confusing. There’s one version of required installation parts in Dacor manual and one version of Samsung parts in the Parts guide, and no one in the team seems to understand the difference and how to map from one to another (they insist on sending me Samsung parts instead, claiming they’re compatible). I am now the expert myself to understand all their parts and able to identify many problems in their manual.2. As a high end brand, Dacor doesn’t seem to care about their customer at all. As a customer who did kitchen remodeling and had no refrigerator to use for five months, no one in the team seems to care about their brand or their customers. With this huge gap in the process, no one thinks about the problem from their customer’s perspective or shared empathy with me. Dacor as a brand is really bad and I am extremely disappointed in both their product and services.

We placed the new Dacor appliances that we’ve purchased in our second home in Big Bear Lake, California. The fact is we were in our second home approximately 10 times in the first two years. We had trouble with our Dacor dishwasher from the beginning. When you close the door, it wouldnt engage unless you close the door a number of times. It became progressively worse to the point where we brought out another repairperson - this time a certified Dacor repairperson. He got the washer going for a few minutes, only to not being able to complete a full cycle. We received an initial $89.95 bill, and during another contact we would have to pay an additional $400-plus for a motherboard and labor. We contacted Dacor, along with the contractor, a number of times. We had the history of this dishwasher which is causing problems.Dacor would not make it good, even though we spent more than $10,000 on other Dacor kitchen products. It simply doesnt make sense to me to not fix a sub-par dishwasher to keep a customer happy. Now, we are angry and will go on a number of sites to advertise our plight. We will install a new Bosch dishwasher as we have no confidence in Dacor and even less in their customer relations division.

I purchased a single wall oven in 2008 and 30 days out of warranty, the oven broke. Service required two service calls to fix the door magnets. A third visit was required as the oven codes shut down the unit. The last two service calls have been with the cooling fan. Now that the fan was replaced, the relay board needs replacement, too. I have spent $650 in service alone, which is separate from the cost of parts. There’s no help from customer service; in fact, the rep was downright rude. I will never purchase this brand again and I have told anyone who will listen not to purchase.

In September 2009 we did a complete remodel of our kitchen. Replaced everything but the refrigerator, with DACOR appliances. Within a few months we had problems with the dishwasher and finally replaced it with a GE in 2012. About that same time we had problems with the Dacor Epicure 30 Single Oven Model EO130SCH control panel and had to have the repairman out to work on the relay/computer board. At Christmas 2015 I had trouble baking, the temperature wasnt accurate and have had the repairman again. He says that the computer board is fried (his term). Ive tried calling Customer Service with no success. Ive e-mailed them with same results. The appliance repairman has told me that he cant find the part. All the distributors that hes called have been told that the part is on back order. Ive been without an oven for over two months now with no fix in sight. Have been told that IF we find the part it will probably run around $500.00. These are appliances that are only six years old and have had gentle use by senior citizens. Anyone reading this - PLEASE DONT BUY DACOR! Youll be sorry as I am.

I was and, I repeat, was a loyal Dacor customer. I gutted and rebuilt a kitchen 9 years ago and purchased a Dacor stovetop, oven and microwave. I remodeled my new house 5 years ago and again purchased Dacor stovetop, oven and microwave. Consumer reports provided favorable reviews of the appliances I purchased below.First red alert: The oven Model MORS130S and Microwave Model DCM 24S LED did not match. The microwave was green; oven was blue. The brochure was in black and white so there was no way of knowing that aesthetically they were a mismatch ... it was very sloppy(!) and very deceptive by Dacor. I mean when I waited weeks for my appliance order and the oven is already installed with a big fat ugly LED screen, what was I supposed to do, yank it out and start all over again? This was disappointing!Next, I was simmering chili on the stovetop (5 burner, gas) and, lo and behold, 18 flames started exiting through the turn knobs resulting in a meltdown. The gas was leaking through the tubes underneath the stovetop. I just happened to check the chili while I was gardening to watch the house almost burn down and btw, it was difficult to put out the flames because the natural gas was leaking under the unit. Seriously! I called customer service and they got hopping right out to fix the issue. This scared the heck out of me. It is negligent to have a product like that on the market.After about 13 months into the life of the Model MORS130S oven, the touch panel failed emitting a CO1 error message. I was told it was $140 to fix it and that the panel was defective, great quality there, Dacor. And the added joy to the CO1 error message is that the unit beeps intermittently all day and all night long unless the power to the oven is killed. Joy... now another issue - Model MORS130S oven LED lights are burning out. Seriously, what else will there be? Now its $175 for LED panel and another $100 to install by an authorized Dacor service man.So I called Dacor back again today because the LED light out was annoying me. They offered nothing. To be fair, my appliances are out of warranty but seriously, Dacor nearly burned my house down. They should be winning me back as a customer if they really cared about their customers and having long term repeat business. Never again, Dacor, never!

We were incredibly disappointed, not only with the range but with the customer service from Dacor. We purchased this range in January 2016 and here we are in July with what is basically a pan holder sitting uselessly in our kitchen. Problems started immediately. The first time I used the oven, it locked with the cooking food inside. It turned out that the thermostats on both ovens were so out of whack that the oven temperature reached self-cleaning mode levels so the ovens locked with the food inside! We had both thermostats replaced twice and still had the same problem. Eventually, the thermostats were calibrated, but still within a range. In addition, the switch for the convection oven just stopped working. After 6 months of trying to deal with this problem, we will be returning the range and replacing it with a different brand. At no point did Dacor offer to exchange the range, they simply kept sending a repair person.

We purchased this unit 7 years ago, just a family of two with visiting grandchildren. Unit came, had a crooked door and a bent latch, which we had serviced and supposedly corrected. When self cleaning the latch still made grinding noises. Over a year ago the oven stopped working period. A December service call said needs a new latch, sensor and display -we are now in 4 figures($). Oven operates for month and a half. January 2019 Service call now new door latch, relay board and main wire harness 4 figures again double! Oven stops working yesterday (June). Service call today new latch, motherboard and something else and another 4 figure repair cost. Same repair parts same problem! Patience is a virtue, but repair costs are sinful! Next step, Boat Anchor! Problem from the beginning and still a problem now.

We remodeled our home and purchased Dacor appliances for our kitchen. Range, love it, Microwave, 30 Double oven and warming drawer (promotional give away). The ovens from the beginning do not function well. To warm up the ovens I have to wait 45-50 minutes and it buzzes. It is at temperature but then when I look at thermometer we are close to 75 degrees below. It recycles temperature every 75 degrees too. We had many repairs to the original unit to the point the repair person recommended that Dacor replace the unit. They did, another disaster. First they dropped the old unit while removing it chipping my granite, destroying my drawer panel and then left an absolute mess. The second unit has the same warm up issues, holding temperatures and oh wait, fans ran for hours after they were turned off. Broiling amazing. Baking and convection, a joke.The last repair person told me to open the oven and turn the cookies to have them cook evenly. And do the same when cooking with Convection. :/ I am currently looking for a reliable double oven that I can use and feel good about the food I serve (to be cooked). Dacor basically said that they cannot help me anymore because we went out of warranty last year and sent a repair person to basically say it is acceptable. Obviously for someone who does not cook, just sayin.

Purchased Dacor Induction Range w Convection Oven RR30NIS-C in October 2013 and LOVE this range. Accidentally broke the glass on the induction cooktop with falling object mid-March 2020. Only the glass is broken, and all other electronics, induction burners, oven, etc are functioning fine. Called Dacor support to acquire part number for a glass top for repair - obtained part number #701751 superseded by #702285, BUT was informed that the part had been discontinued and is no longer being manufactured or kept in stock. No other advice was given other than to discard the entire $6000 range. Multiple phone calls with service.I asked for a listing of third party part distributors and was referred to four distributors on the Dacor public website and given no other info. I called all web-based third-party distributors I could find in USA and Canada to see if anyone had the part in stock, with no luck. I contacted two technicians to see if they would be able to obtain the part through their channels, with no luck. I am an engineer, so I spent some time pouring over technical manuals trying to find a solution to replace the entire induction range cooktop assembly (top part of the range) with a later model, and although its possible, Dacor would not provide the ability to purchase an RNR30NI range cooktop assembly that could be fit into the existing housing on top of the range. The convection oven is completely fine, and I cannot believe that Dacor has given me no other option but to pitch a six-year-old $6000 range because they stopped manufacturing one fragile part made of glass. I would imagine that many consumers may be in the same position as I, as these cooktops are breakable, and accidents happen. I have reached out to Dacor support desk numerous times without resolution, and I am at my wits end with a $6000 boat anchor in my kitchen. What a waste of money! Poorly done Dacor!I would like Dacor to provide me with some sort of solution whether it be the part required to fix my induction cooktop, or a replacement Induction Range with convection oven, or reimbursement of the purchase price so I can obtain a replacement on my own. If I am not able to find a solution to repair my range, I will never buy from Dacor again! Dacor will discontinue easily broken parts without warning! You may spend thousands of dollars and not be able to repair your appliance after warranty expires!

If anyone else has this experience with Dacor ovens, we need to have a class action suit against Dacor! While baking Christmas cookies this week with my grandchildren, my ovens stopped working and started beeping. The error code was F3. I was able to get a technician rather quickly who diagnosed the problem as a failure of the control board which affected both ovens. The replacement part was discontinued from production in 2011. My ovens are 12 years old and cost over $4,000 at the time. What a pickle I was in a week before family coming for Christmas dinner!The technician said my only recourse was to send the control board to a refurbisher and he did not know when the board would be fixed - all for a whopping costs of over $600.00! I find it unacceptable that Dacor discontinues a control board and forces the consumer to either buy new ovens or pay the cost of a refurbished part that I hope will work. After spending thousands of dollars, how does this happen? What can be done so the consumers who purchase appliances with good intentions are protected from manufacturers that dont stand behind their products? DACOR I NEED ANSWERS!!

We have had our Dacor since 2006 and this range, the most expensive appliance we have ever owned, simply doesnt maintain the proper oven temperature. We have owned several far less expensive ranges and their ovens, much more basic designs, do what an oven is supposed to do maintain a temperature! We cook or try to quite a lot but working with this stove is like baking over an open fire while camping. This supposedly gourmet, fancy, convection oven that supposedly can bake cookies and meat at the same time is a total fail. We have had the service people out repeatedly to no avail. I am convinced we could change the circuit boards repeatedly and it wouldnt make a difference because it is a faulty design. This product should not be on the market or this company and their poor service in business. DO NOT BUY THEIR RANGES! Unless you dont cook and all you will do is look at it. We are thinking about retaining an attorney to file a class action suit. We could buy a low cost oven that works several times over for what we have paid in repair bills.

We bought a 36 inch Dacor range with oven last year, around September, when we moved in to our new house. We tried to turn the oven on Thanksgiving day for 10 people, but it would not work. We called for service, and they replaced the circuit board. The repairman turned the oven on, and it worked fine. We never used the oven, just the burners on top, because we have a second smaller oven, we like to use for every day cooking. Then came Christmas day, and we were having 30 people over, so we went to turn on the Dacor oven, but to our horror, it did not work again. We have owned this oven for a little over a year, and have tried to use it only twice. In that time, both on holidays, with a lot of people to feed. This time, when I called for service, they told me I will be charged $198, because when they tried to get Dacor to drop that charge, they said no. We are very disappointed in Dacor for not caring more about the customer.

Warning: Warning, safety hazzard for all, adults and children. Recommendation: The knobs should be set on the top of the stove, not the front where children can reach. Control knobs should click when fire and gas is turned off, and highest flame setting should be at the end of the turn just like a clock. I inherited this range as new owner of the house. Today I used the high flame option of the gas stove. When I was done with cooking, I turned off the gas according to the knob position, front of the turn. Later I discovered the range was not exactly off. It was still hot but no flame could be seen.I checked by sight the control knob position, it was set incorrectly in off. Then I touched it and realized the knob actually has a bit more to go to the end, slightly before the off position. Therefore it continues to release gas with unobservable flame. This knob does not click when user turns it to the off position. It is just a silent knob with an inaccurate cue of a heavier black line for off and on indication. Besides, high flame setting comes at the beginning of the turn of the knob rather than the end, it is counter intuitive to our mind of increase heat by turning the knob further on, like our clock. Oven racks are hard to put back after cleaning. Once a rack almost tumble out while food was sitting on it.

We purchased a very expensive Dacor double convection oven about 15 years ago. This was based on recommendations from friends who do a lot of cooking like we do, and the mistaken thought that this US company would be more inclined to support any future problem. We now have a problem with the control panel. Dacors only response is that they do not make the part anymore and cannot help us remedy the problem. They even had the nerve to say that they would give us 10% off a new one. Except for the annoying buzzer sound, the stove works well. Buying a new one is a financial burden we never expected or want to accept. We are telling all of our friends to stay away from this manufacturer. I wish I did not have to give Dacor any stars.

We remodeled, added a very upscale kitchen in 2003, and chose Dacor appliances, 36 inch dual fuel stove, 30 inch wall oven, microwave, and a 30 inch dishwasher, well over $25000 worth. NONE of the appliances has worked properly, but the dishwasher has taken the cake. I have lost count on how many times I was in contact with the customer service. The digital board went bad, the error msgs kept coming for years! The racks/baskets rusted after just a couple of years! After numerous encounters with anybody I could get a hold of they were finally replaced, but not the right racks because they do not fit, falls off the side every time I use this dishwasher. I cannot tell you how frustrating this has been! I was eventually told that I could not complain anymore because I was out of warranty and they would not respond anymore! I am stuck with this $3000+ dishwasher that I cannot afford to replace, because I would have to rebuild that area of counter cabs in the kitchen! The service has been horrible. This was the most costly mistake purchase I have ever made.

Our 30in Dacor double ovens are approximately 12 years old. I feel they operate adequately. However, not better than our much lower end appliances we previously owned. My main complaint is the self cleaning function. My old ovens self cleaning worked much better! With our Dacor ovens one must take out the racks and clean them by hand. This is very difficult and time consuming. I used the 3 hr option to clean my oven that was moderately dirty, mainly from cooking a prime rib over the holidays. After the 3 hr cleaning the oven was still very dirty with splatters and grease. Im now cleaning my oven again with a second 3 hr cleaning cycle. I know at the end of this second cycle I will need to do a lot more cleaning by hand! I hope Dacor has improved their inadequate self cleaning feature. If it hasnt been improved, I really cant recommend Dacor ovens.

I would never buy another Dacor product. The microwave totally crashed and now the oven will not heat. I have had contact in the past regarding repairs and they are outrageous. I plan to replace both items rather than paying unreasonable costs. Very unhappy.

Bought to replace 15 year old same model and I'm hoping I will get another 15 years out of this one as well!!! Great price and delivery!

I have an older cooktop. Yes it is 15 years going strong but I have ran into a few issues where I know the repairs would be pricey but especially the parts. After talking to a few representatives, they truly want to help you. Nothing is free and I don’t expect it to be, but I am glad they they helped me get my cooktop back to functioning again. I hope someone finds this helpful before reading or writing bad reviews.

I have the same problem Judy had last week. I have a 36 inch under counter oven. I use it all the time. I have had it for about 10yrs. In the last year the computer has been replaced 3 time. The first time it cost me $600.00. 6wks later it was replaced for free. Now the oven is having the same problem. I hope Dacor makes me as happy as Judy.

We bought our house in 2010 and our Dacor stove was supposedly newer. When I went to clean it, I found loose screws in the bottom. Apparently, the convection element is loosing its screws and washers. Ive had this appliance fixed once already when the cooktop kept clicking. The black plastic around the controls cracked mysteriously. It takes 3 hours longer to cook a turkey than it should. This is a strange stove, which supposedly cost a lot. I wonder if a convection part missing two screws should be used?

My Decor Epicurian oven and range has been a nightmare from day one. I have had the oven for about 8 years and had it repaired so many times I have lost count and had spent at least $2000 on repairs. We have experienced motherboard burn out, membrane failure, temperature control malfunctions, error messages that cause incessant beeping. Nearly all of the problems that have been described in this list of complaints, I have had the problems themselves multiple times! Now, I am panicking a bit because I decided to use the self clean function on my oven this morning and now, I have read some sad malfunction stories following the use of this feature. I am so torn about whether I should just cancel the cleaning process. I do not want to risk having the oven malfunction again, but the thing really needs to be cleaned.

This will be the third service call on my Dacor Built-in Refrigerator with the freezer making icicles and the fan making a loud noise. On top of that, I have two light bulbs in the freezer that went out from the ordeal. From my review of the complaints here on Consumer Affairs, I see Im not the only one with this issue. This is a yearly problem, and I hope Dacor would step up and resolve this for me since it truly is a poor design issue and no fault of mine.

Our initial dishwasher had many problems. After several service calls, we called Dacor to identify the issue and see if there was anything they could do for us. We received a brand new dishwasher (even better than the initial one) for a nominal cost. We would like to thank Dacor for their excellent service and attention. Its not always the issue, but the resolution that makes the difference.

I paid over $6000.00 for a Dacor EF48BNDBSS refrigerator and have had nothing but problems with this item and the other Dacor item (dishwasher) that I bought when I had a new kitchen built for my new life of retirement. The first refrigerator that was delivered did not work when it was installed and was returned immediately. I had to wait for Dacor to send another one and I have had to pay several service calls each time since that point. I am disgusted that I paid over $10,000 on two appliances from Dacor and neither of them has ever worked even at a low grade basic level. Both of my items have been discontinued and Dacor reimbursed me for half of what I paid for the dishwasher, which did not even cover all of the repair calls that I had paid for ongoing service. At that dealing, I got tired of paying for repair calls for the refrigerator due to excessive icing in the freezer; supposedly there was a quick fix right after I had the unit installed and it did not fix the issue. Now, there is another quick fix that Dacor suggests and that will cost me $800. Really? I dont think so. In fact, I have researched this issue and have found that this quick fix does not solve the problem either. In addition, I have called Dacor numerous times about the refrigerator door not sealing and the refrigerator making all kinds of strange noises. They told me it was the seal, so I had the seal replaced and that was not the issue. Then I paid $235.00 for a service call to look at the seal and he said that this refrigerator has known problems for hinge issues and he attempted to fix the hinge and left and the problem continued. Between the hinge issues, the constant icing issues in the freezer and the food icing over as well along with the trays and inner shelving of the freezer, the refrigerator sealing and the hinges working, and the constant crazy noises that the refrigerator makes, I am ready to file a lawsuit for a lemon of a product. This is the second product that has recall issues and multiple problems. I am sure that with my documentation, a judge would have no problem agreeing that I have paid way too much and put in way too much time and energy into getting a decent appliance into my kitchen. I would never recommend Dacor to anyone. I am dissatisfied and refuse to pay another penny for service calls on these appliances that were installed in 08/2012. At this point, my refrigerator is unplugged and unusable and I am using a small refrigerator that I bought at Costco for $300.00 thirteen years ago that has never had one problem.

I have the Dacor 30 all gas range in my house and it is the best. The grates take up the whole top surface of the stove area, so I have a ton of room to cook on. Basically, I can fit 4 giant pots on the stove at the same time, so Im ready anytime a chili cookout might break out. This is also super convenient during tamale season and soup season because I can put up to 4 giant stockpots on the stove simultaneously. In the event that I spill, its easy to remove the grates and give the surface a nice wipe up. As far as the oven, I totally rule the holiday season because I can fit up to 3 full size 18x36 catering sheets in at the same time, so basically, I can cook 4 dozen or more cookies in one shot, leaving me tons more time with family and friends than if I was baking 1 sheet at a time. Thank you Dacor!

We just purchased our home in March of this year. The previous homeowner purchased a Dacor oven; it is electric & propane. She purchased the appliance after a complete home renovation in 2008. They lived in the home. After 1 year, they moved out and had it on the market. We purchased the home in 2012. As soon as we moved in, we noticed the oven was not working. We called an appliance repairman - $564.00 service call and part for a new relay switch. It was great; the oven worked. Not even a day later, an F1 error. We called them back out thinking they must have done something incorrectly. They then said we needed a new control panel. We did not have an additional $400.00. We just moved, so he said you could still use the oven. We did. We would use it and flip the breaker off so we did not have to hear the annoying beeping sound. Then I came home and bam - no display, no oven. We called a different Dacor certified appliance guy thinking the first company was just taking us for a ride and it was their fault. $572.00 later, we got a new control panel, but guess what, the technician did not even make it to his truck before beep, beep, F1. He came back in and then said we needed to replace the display screen - an additional $217.00 with no labor charge. We told the man to shove it. I had every plan of taking the oven to our back tank and using it for target practice. But in good business practice, since this company already invested $572.00, we could not ask them to eat the money, so we allowed a third fix of the oven. While the technician was here, the oven made a horrible loud sound and shot out flames. He insisted maybe it was due to it sitting for a week without use. He left. I never noticed this flame before when the oven worked despite the F1 beeping. Now it’s hit and miss. Some days it will shoot out a flame once until it reaches 200+ degrees and then you can hear the fan kick in. Some days, twice, I have had it happen 3 times. If my children were to open the door during this event, I am sure they would be seriously burned. At first I was thinking maybe it is normal for this oven to shoot out flames during preheat mode since after $1300.00 repairs maybe it is just not functioning correctly. But if it were a normal function of the product, to me it would do it every time consistently and not three times, or two times on some occasions. I hate to admit this but I am almost fearful of using my oven. I currently have a pie to put in for dinner and I’m thinking its 3:09 pm; I could set the oven to preheat while I run to get my kids from school so if it decides to blow up, I am not home and that is pretty sad. The last repairman we had come out said in his personal opinion, he wouldn’t have repaired the oven, because they are known for issues, and he would have gone to Lowes and spent $300.00 on any off brand stove first. We have considered that, but this stove is extra-wide and the cabinetry is built around it. So for us to purchase an oven to slide right back in it would be another $1300.00-$2000.00. We have issues with the burners not always wanting to light. I almost caught on fire lighting one because it shot out flames when it decided to finally ignite. Sometimes it just clicks. Currently, I am down to two burners when just two days ago all six were working just fine. Over Thanksgiving, it took no kidding 1-hour to cook brown and serve rolls because the oven did not reach the set temperature. We stuck my husband’s bbq thermometer to see. It was 256 degrees, not the desired 350 degrees. Does this stove have warranty? We have no clue as the previous homeowner purchased the stove. She claims to have spent $5,000.00 on this stove or more during their purchase. We do not have warranty on our home so for each repair, it is out of pocket for us, and currently we really are thinking any knock off brand at Lowes would be a better product than a Dacor oven and less of a safety hazard for our family.

Purchased Dacor Renaissance wall oven in July 2015, Model RNO130S. After less than a year and a half, the cooking temperature began to fail. For instance, set to bake at 425 degrees, the oven would appear to heat properly, but tried and true recipes would be pasty and uncooked at the expected time. I inserted an oven thermometer inside to test and found an erratic pattern of oven heating up properly to 425 but then sometimes dropping back to about 350 during cook time and refusing to ever reach 425 again. ABT repairman adjusted temperature calibration but refused to troubleshoot any further. Just ruined another dinner. Thanks Dacor and ABT for your unreliable product and poor service.

When we recently remodeled our kitchen, we replaced our Dacor double ovens that we had had for 15 years. These were great ovens and not one problem with fairly heavy use, so we bought the Dacor Modernist double ovens. The ovens are usable, but they are the worst engineered product I have ever experienced. First, there is no clock on the stove because as I was told the clock would etch the screen if it was on 24 hours a day. Second, the sound the timer makes is so soft, even on the loudest setting, cannot be heard in any room but the kitchen, so I paid a premium price to carry a timer with me, so I know when my oven is done baking. Third, if I turn the oven light on, the timer either stops completely, or it resets to the original time. Fourth, the oven buzzes when it is cooking. Fifth the user manual is useless and there is no video or online information on how to use this oven that is not user friendly.Finally, I have talked to Dacor and have had the repair person here, but he knew nothing about this oven. I am sorry every time that I use this oven that I did not buy my other choice, which was the Woof double ovens, but we thought this would be wonderful product, like the wonderful product that our previous ovens were. We also thought Dacor was a family company, but is now owned by Samsung. What a disappoint these ovens have been. The engineering for this product is a disgrace for any company and I no longer see the Modernist products advertised and it may be because it is such a poorly designed product. I never met a computer that I did not love, but this is not the electronic wonder that was advertised when we bought the ovens.

For the second time in 7 years our Dacor ERD 48 Range has failed us. Just in time for our New Years Day dinner. Neither of the two ovens will heat. We are now encountering the exact same problem. We spent $1000 the first time replacing the board. We cannot afford to do it twice.

We thought we bought a quality product when we remodeled our kitchen two years ago and put in a $3000 30 inch wall oven from Dacor through their dealer Friedman’s in Knoxville. We had heard for years that their products were top notch and high-quality. I find it interesting that the oven has a self-cleaning function. However Dacor Technical advised me that if you use the self-cleaning function you will create too much heat and destroy the motherboard. Wonderful input after the fact. The oven now does not keep a correct temperature and we are advised that our oven is two years old and out of warranty and we should not have used the self clean function. Really? Why is the button even there. Do not under any circumstances purchase any Dacor product. I feel comfortable in saying Samsung will add absolutely nothing to the quality or service. The lack of customer care and concern is beyond reproach. One star rating is way too generous. How do you just walk away from your products. We used our clean function exactly once and nobody ever said it was a self destruct button.

We did a full reno on our house starting in 2018. With a brand new kitchen we felt higher end appliances would help finish it off nicely. We settled on Dacor from our appliance dealer due to the look a past history of great reviews. Had we known that the original Dacor no longer existed and it was now Samsung with Dacor nameplate we never would have bought them. We have had 15+ service calls for the fridge and oven. Oven didnt work from day one and required multiple board changes. The interior is not level so you cant bake a cake and the racks are impossible to remove without bending the rails. It just failed again last night just as the warranty expired. The call center is in the Caribbean so dont expect any help from customer service. The ice maker with the fridge is a continual problem so we had to buy an $100 ice maker that now sits on our counter full time. These appliances have a high end price tag but are not high end!

Dacor dual fuel 30 inch range - First of all the look of the dacor is second to none in my opinion. The digital screen with blue lighting makes this a truly elegant part of any kitchen..... when it works. The range top itself worked flawlessly for me and the main burner was always more than enough. The problem with the range lies in the electronics. The unit has been in my home for over a year and has worked for less than a month total. An error code appeared when ever the oven gets hot. C33, C1, 0000, 1111, C11. Ive seen it all. I have had the main board replaced twice and my local repairman is on first name basis with even my dogs at this point. The final straw for me was when the oven door glass shattered while cooking and when dacor was contacted they said that happens. Im think Ill try Viking.....

As I have read in most of the reviews, we have also experienced the control panel on our 30 inch dual range cracking over the years. We were told not to replace it because it would continue to happen. Ok, lived with that... Now something new has started to happen, the plastic handle on the oven door and surrounding area has started to melt. It got so bad after a self clean that it is collapsing. Now there isn’t much of a seal at all when the door closes. The stove isn’t brand new, but this has to be a fire hazard, and consequently, now the oven will not even turn on. I’ve reached out to Dacor with no response yet. I’m done with this company!

2017 purchased 36” range. First year- self cleaning overheated, replaced part. That was in 1 years warranty. But now: only 3 years barely: (I dont even cook much). Oven turns off by itself if I open the door. Oven does not turn off when I am done cooking. If I cook 450f pops warning of temp overheat. Called ABT service (this is where Dacor said) it cost $219 for a service guy to call dacor and to give me answer: I think it is android board. I have to buy a board. Plus per Dacor this board will not have wifi. So there is no Discovery- paid extra for extras I can not have...

I have a Dacor refrigerator that cools poorly and needs servicing. Refrigerator manufacture date March 2017. When I acquired the refrigerator I signed up for the Dacor standard warranty (1 year) and the Promotional additional 2-year Dacor standard warranty advertised as 3-For-Free warranty. I contacted Dacor customer support by phone today. After an hour on hold, they said that they would have to check with their supervisor. 2 hours later I received a call back saying that its only a 2-year warranty. Their website where I registered my product (warranty.dacor.com/member) clearly indicates that my refrigerator is still under warranty. When I confronted them with this, their answer was anyone can register anything on the website and it proves nothing. In other words, registering your product offers you absolutely no protection.I provided their supervisor all documentation requested, (including proof of title of ownership of my house!), and they still repeatedly stated its only a 2 year warranty. When asked where they are getting this information, they simply said thats what we have in our system. I asked to speak to a supervisor, but they said none were available. I left a message with the supervisor, but none ever returned my call.Dacor continues to offer their 3-For Free warranty to this very day. As a busy physician, I keep good records and pay attention to detail. Dacor has been to my home previously without incident. I am extremely disappointed in what appears to be the companys blatant attempt to deny warranty coverage despite ample documentation that its still covered. I would caution folks that their 3 year for Free warranty is simply not true based on my personal experience today. I will no longer be purchasing any Dacor products because of this, and will relay my story to anyone interested in purchasing Dacor products.

We have a 2 year old 36 inch, Model EF361WF refrigerator. Water began pooling at the base every 2-3 days. Called Dacor Customer Service Team. Pitiful response and horrible customer service. Had to call private technician who was very surprised that a so-called higher end appliance was not factory-fitted with a P trap. He sees the problem often with cheaper models. Dacor has let us down twice. Buyer beware: sub-standard products matched with sub-standard customer service. Dacor will never get our business again and we would recommend all potential purchasers to consider other brands.

We built a home in 2006 and installed all Dacor appliances. I would never ever purchase these products again. My gas cooktop was the top of the line product from Dacor and I have had nothing but problems with it for 5 years now. I have spent over $1000 fixing the large burner that continues to have leaks with the seal to the point where the flames come out the bottom of the burner. Most of the other burners click when lit even though they are clean and away from a draft. I have had 2 Dacor approved repair companies out and they both recommended against Dacor. In addition, the finish on the cooktop has soaked in my heavy duty cooking juices and foods and the stains will not come out. Apparently, this is due to the new finish they used so that the metal can withstand the high temperatures. If this company were an auto mfg., they would have had to do recalls and face potential class action suits. I would prefer to be cooking on a camp stove rather than my Dacor. When I contacted Dacor, they offered parts at a reduced rate which still cost a fortune. When I asked about replacement, they said they would sell to me at a discounted rate which was still $2400. Bad product, bad company. My cooktop is still giving me issues. it is embarrassing to cook with friends around because of the problems.

We have a Dacor Epicure 36 six burner range. It has been a regular source of trouble since it was installed as part of a kitchen remodel in 2006. The igniter for the broiler went out 18-24 months after we got the oven. A year or so after that the weld that holds the bottom oven rack bracket to the oven itself popped loose making it impossible to use the lowest rack position in the oven. Last year the circuit board that controls, among other things, turning the bottom oven element on stopped working. Not only is the board itself quite expensive, but it is buried deep under the top of the stove taking lots of expensive hours of repair time to remove and replace. And now the burner igniters have begun to over spark (e.g., continue to click long after the burner has been lit, burners sparking that have not been turned on). The repairman tells me that is a different circuit board so we could be heading to another $500 or so in repair bills or perhaps a trip to the dump and a much cheaper replacement range. We have had other Dacor equipment (cooktop, wall oven, warming drawer) and have not had a problem with any of them. But given our experience with the Epicure I cant imagine ever buying another.

After less than a year after installation the oven continues to operate poorly. Its been recalibrate twice and a new control board installed. Did I mention the board had burned components? It still does not operate properly. Its at least 25 degrees off. Everything takes way longer to cook than it should. Thanksgiving was 2 hours late. Christmas was the same. Entertaining during the holidays, embarrassing. Now Dacor wants pictures to prove to truly see how poorly the oven is operating. I thought I bought a quality product but I was wrong. This is just following suit with the Dacor refrigerator I purchased and was replace months later.

My wall oven spontaneously heating to 800, will be fixed! Thank you, James of Dacor for contacting me again and for arranging for my wall oven to be repaired at no cost. When our oven is in top working order, we love the convection option and we love the internal temperature probe. The people at Dacor offer the friendliest service I have ever encountered and I thank you so much for that.