Dacor double oven range turns off by itself while baking - Disappointed in Dacor, especially today. Thanksgiving 2016: baking turkey. Sill baking turkey. I dont know when the oven decided to switch off this time, but I have an uncooked turkey and guests waiting. The oven has done this before, but because it was new I thought it was user error. Nope, the damn oven mysteriously turns off on its own. Incredibly irritated with Dacor. The range hood we also purchased is a joke. We remodeled our kitchen 1 year ago and wanted quality appliances. Bad move. Save your money, folks. Save your money.UPDATED ON 03/10/2017: Dacor sent a company out to fix the broken new oven. Oven still cannot hold its temperature (It takes FOREVER to heat then loses its heat while still showing a high temp). This time I have a recording on what happens when the oven automatically switches off. Disappointing when we spent nearly $10,000 in Dacor appliances for a kitchen remodel. DACOR, please have a rep contact me!!! Still waiting to hear back!!!

I will NEVER buy Dacor EVER again. We built a house and after looking at other high-end appliance makers and upon my mothers strong recommendation, we installed all Dacor appliances in our new kitchen. My mother based her recommendation of Dacor appliances due to what she explained as their excellent customer service. HA!! Less than 3 years after installing our pricey Dacor Epicure over-sized dishwasher it has rusted racks -- top and bottom! After experiencing a very painful, drawn-out and EXPENSIVE process of getting our racks replaced, I am not confident AT ALL that our frustrations with this dishwasher are over yet. The new retrofit slides on the top rack are so lightweight I cant imagine they will effectively operate for years to come. I have difficulty closing my dishwasher properly now and have to check each time I run it for leaks on the floor. Ive given up on my Dacor dishwasher and have resigned myself to eventually replacing it. NEVER buy Dacor!

Years ago I purchased the Dacor Double Oven over a Thermador because the Thermador had a ridiculously long pre-heat time. The Dacor has performed reasonably well as a oven particularly in convection-bake mode. But over time, components started failing and repair parts were hard to find, unavailable or ridiculously overpriced. I am an an engineer with DIY skills honed from years working with high tech food manufacturing equipment and controls including ovens. In recent years, I have needed to replace a relay board, the main control board, hinges two times, and most recently the hinge receptacles. I have also replaced an inner panel on a door assembly. Just think what such repairs would have cost for an average consumer. I understand the parts can fail, but Dacor has shown little regard for consumers in my opinion. They have done very little to maintain an inventory of repair parts. Basically their message is that the part is now obsolete and unavailable. Thats some answer when the price of a new double oven is multiple thousands. Recently, the hinges on my upper oven failed again. As they failed, their failure caused increased wear on the hinge receptacles. Soon the receptacles failed as well. I was able to find hinges at a ridiculously high price but the receptacles were unavailable anywhere. I contacted a several parts suppliers who told me that they had no idea when the parts would be available. Moreover at least two of the suppliers mentioned that they had a backlog of orders for the receptacles - one had a backlog of over thirty. Yikes!. At that point I contacted Dacor customer service and asked what could I do to get the part. Answer: The part is unavailable and we have no estimate on when it will be available. I tried to escalate my request and got nowhere. Finally after many hours of online searching, I found one set of the hinge receptacles at a price 4X last years price. Lastly as I replaced the receptacles today, I realized that the mounting screws only hold one portion of the U shaped mount. If the screws were longer, the receptacle would be less prone to twisting and wear. Be aware that Dacor was sold to Samsung a few years back. Based on my experience, I could never recommend Dacor. Caveat Emptor!

This fridge is great. We visit warehouse stores for groceries and everything fits perfectly. The shelves can move for tall items or more bulky ones. The freezer is large and can fit so many different items. My 2 other favorite things are the fresh drawer and auto refill water pitcher. The fresh drawer temp can be adjusted and can fit anything from wine to a cake to cheeses and meats. And an auto fill pitcher keeps the water super cold and you never have to worry about someone forgetting to fill it back up.

We had a ongoing problem with a wall oven that was purchased in 2006. The most recent complaint was a oven glide rack that was not working. After complaining about it to one of their staff, they listened to our frustration and are sending us a new rack at no charge. My hats off to the great people at Dacor. Thanks for your understanding. Al

My wall oven spontaneously heating to 800, will be fixed! Thank you, James of Dacor for contacting me again and for arranging for my wall oven to be repaired at no cost. When our oven is in top working order, we love the convection option and we love the internal temperature probe. The people at Dacor offer the friendliest service I have ever encountered and I thank you so much for that.

Our refrigerator is 5 years old and has had a problem with icing up in the freezer area, resulting in a loud noise from the freezer fan. We originally called Dacor for service but they could not get to it for 2 weeks. An appliance repairman installed a new heater for the defroster. This only worked a short time and happened twice with a cost of over $1000. A couple of months ago, it happened again, and we were able to get a hold of ** at Dacor customer service. She knew exactly what was causing the problem. She ordered the parts and directed a factory-approved repairman to install over $800 in parts and we are confident the issue is resolved. Thank you, Dacor, for standing behind your products.

From the beginning, August 1997, 17 years ago, I was not able to use my oven after self-cleaning. The problem was never resolved after countless service calls totaling over $1500. Aside from the cost, I was inconvenienced every time I cleaned my oven, as I was not able to use it until it was serviced, about a two week wait. I contacted Dacor early on and they reluctantly agreed to extend my warranty for a year. They did nothing beyond that, and my oven still shuts down after self-cleaning, which I hesitate to do at all, until it is beyond needing cleaning! The circuit board was replaced and recently the cooling fan was changed, but....no luck. Buying a new oven is not an alternative, as the oven performs well in every other way and I simply cannot afford one. I cannot believe a company of such status is not interested in satisfying its customers.

As a contractor, we were fortunate enough to build our dream home which was completed in 2005. After much research and many show room visits, we purchased Dacor appliances for our kitchen. As the saying goes, if I knew then what I know now. Our biggest (note I said biggest, not only) issue is with our ESC130 oven. If you own this oven, do not, repeat, do not, use the self-cleaning mechanism. I have had this repaired once and then replaced once (along with a relay board). I seldom use this because I know when I do the lock mechanism will continue to cycle until it is replaced. This means, while I can still use my oven, I have to time when I open the door based on when the lock is cycling in the unlock position. I must also turn the oven off at the circuit breaker or listen to the continuous warning beep that the lock is cycling (as if I didnt know).After repairing this feature once, I next choose to have the mechanism replaced and Dacor offered me a discount on the parts (the oven was and still is out of warranty) at a cost of more than $500.00. This is on top of what I had already paid to have it repaired just 18 months earlier. I feared using this feature again as I didnt want a repeat performance. After cooking macaroni and cheese yesterday, I felt I really needed to clean the oven and made the mistake of using the self-cleaning feature of the oven. I dont know why I was surprised when the locking mechanism refused to stop cycling.I contacted Dacor today only to speak with the rudest customer service representative I have ever encountered, Steven. No last name. He is the only Steven who works there. He refused to listen to me, spoke over me when I did try to talk, and did not allow me to speak with anyone else. There are no supervisors available on Fridays and he could not transfer me anywhere. I left a message for someone else to call me (they did not). I called back later that afternoon and was given the name of a supervisor, Nhi. She was not available and I spoke with another customer service representative. I learned that Dacor is aware they have a problem with this locking mechanism and are trying to correct it. This got my hopes up, thinking that the company would now do the right thing and replace this mechanism at not cost to me, or at least at no cost for the parts. Not so. Even though Dacor knows there is an issue with this mechanism and they are supposedly trying to correct it, all they can offer me is a discount on parts. Really? Wow! A discount for a part that you know doesnt work properly and probably wont work properly because they are still working on the problem? I just really dont know what to say. Is this supposed to make me happy as a customer? Would prospective customers want to buy a Dacor product knowing that Dacor is more than happy to sell me a known defective product at a discounted price and they should expect the same? It is probably needless to say that I would urge all prospective Dacor owners to not waste their money on any Dacor product as they do not care about their customers. I will certainly be doing my part to warn others and hope this serves to warn others as well. Dacor has a lot to learn in terms of building even what could be called a good product and standing behind what they sell as well as becoming a customer service oriented company.

We purchased a Dacor dual fuel oven range in 2008 in conjunction with an extensive kitchen remodel. It was beautiful and expensive. It has had innumerable problems. 2008: One of the igniters broke requiring replacement. 2014: oven stopped working, required new relay board. June 2020: Relay board again broke, oven stopped working. December 2020: Oven stopped working, heating element broke. These were serious problems each resulting in 1-2 months without an oven as the parts had to be special ordered. We have not had an oven since December 2020 (it is now March 2021). We are waiting for a replacement part. In addition, minor problems included a broken indicator light and burner grating. Dacor customer service was only moderately helpful, referring us to local repair companies that had difficulty obtaining parts. Dacor has told us that this should last decades but we are seriously considering replacing it after 12 years because it is very unreliable. I would not recommend a Dacor based on our experience.

I bought my Dacor epicure 36 duel fuel range in 1998. First stove: oven door did not close, spark modulator out. They tried to fix it but failed. They sent me a new stove. #2 stove: same problem with spark modulator. Couldnt use any burner without the constant clicking. Oven didnt bake evenly. Complained. Stove: #3: same problems. Dacor sent me a letter to grade them on their stoves and service. I blasted them. They called me and ask if I wanted my money back or another stove. Stupidly I took the stove. This was 5 years since the original purchase. Ive had this stove #4 for 13 years. Door is and always has been unable to close. I use a stick to close it. Now the relay board is out. Frankly I so love the looks of the stove and I cant afford to get a new one. Original was 5200. Now they are 6700 and I would probably have the same problems. So I am going to try and fix this stove myself. I will never buy Dacor anything ever again, even if I could afford it. When they offer your money back, take it. The service was responsive although didnt solve the problem through 4 stoves. I would gather from that, the design is bad. My mother has a old 1940 gas stove that still works. Gas stoves should not be that complicated.

I have own my range for about 2 years and for the most part it is used every day. I love the simmer burner and how strong the rest of the burners are. My food always cooks well both on the stove top and in the oven... I love this range.

We purchased our home brand new in August 2006. The house was built and the appliances installed (but never used) in 2003. One of the things that sold us on the house was the kitchen being comprised of all high-end Dacor appliances (double convection oven, cooktop, dishwasher, and built-in microwave). Our excitement quickly turned to frustration. The first problems began with the dishwasher, which after several attempts at repair (circuit board) was begrudgingly replaced by Dacor, with “begrudgingly” being the key word. I have always found Dacor customer service to be rude and dismissive - with the only way that I ever received a satisfactory outcome, being via threats of contacting the BBB and Missouri Attorney General.About a year after receiving the replacement dishwasher, the internal racks began rusting badly. Once again, I called customer service who originally wanted to sell me new racks at a discount. Only after another persistent round of explaining that high-end dishwasher racks should be made from a material that doesnt rust, complaining and threatening, did I receive new racks free of charge. I was also informed that they had changed rack manufacturers and that would eliminate the rusting problem. Wrong. It has now been another couple of years, and the new racks are rusted worse than the previous ones. That is just the dishwasher.Our Dacor microwave display began slowly losing its LED display about 2 years ago. Lately, the microwave interior lining is beginning to disintegrate and rust through. One of the burners on our gas cooktop makes a constant popping noise when lit. The top half of our double convection oven no longer heats beyond 250 degrees. I realize that our appliances are now significantly beyond their warranty period, so I am no longer even attempting a resolution through Dacor. I will most likely ride these appliances into their graves and replace them with another brand. I am writing this mainly to alert others about my experiences with what I believe to be Dacors total lack of quality at a premium price. In my opinion, Dacor is all style and no substance.

Arrived in good condition and so far works perfectly. Delivery was delayed by one day because of the incompetence of my local mail service. I bought this microwave, as others have described, to replace a 13 year old Dacor that had not really died but had lost the electronic screen. We put magic marker numbers on the display screen where the numbers had been 5 years ago and kept using all the functions. I decided to replace as, without the display screen, I could not do anything semi sophisticated with this microwave but its motor and microwave capacity was still going strong. This model fits perfectly into the previous 24/27 trim kit. Unfortunately our other trim kit is white to match our old microwave. Decor only has stainless steel now. And the new trim kit for this microwave is flat without the vent slats (plus costs over $300!). From the placement in our cabinet, I think the vented slats are really important to dissipate heat and am puzzled by the change in design by Dacor. The slats are a little tedious to clean but as a TV is above the microwave and an oven below I want the heat to have a better place to go. Ebay has the old trim kit in stainless steel but so far the expense seems excessive for just the outside piece. The internal support bracket for the new microwave is exactly the same as for the previous model so the only part of the trim kit needed for my microwave is the outside frame. This newer model works very similarly to the older version. I am delighted Dacor still makes this microwave to fit my space 13 to 15 years later.

This range has never cooked anything well, overlooked and undercooked. Several technician visits, board replaced, thermostat replaced, starts error messages and clicking all on its own. Recently the cooktop has exploded with a big BOOM 3 times. We finally turned off the gas and Im cooking outside with the camping stove and BBQ. I am so upset about the explosions that I am shaking. Today it exploded while all knobs were OFF. Im thinking about getting an attorney. IF my house caught on fire my insurance would not pay unless I do everything in my power to mitigate damages. No gas should work, but I would like to be able to cook in my beautiful kitchen with my granddaughter. Help!

We purchased a Dacor 30 Heritage Gas range and installed it in early Oct 2020. Within a day a gas leak from the back of the range was identified by our gas contractor. Dacor repaired it quickly (12 hours). I was impressed (though concerned it already had an issue). In December 2020 I noticed that the oven indicator light was not coming on. I contacted customer service and despite indicating that there was a problem, was simply told what the light was for. Then, in February 2021 (under 5 months after installation) the oven stopped working. The service technician indicated it was an electrical issue and the gas would not ignite. It has now been over two weeks and we still do not have it repaired nor any indication of when it will be repaired. We spent $5200 on this range. I do not recommend Dacor.

I have the same problem Judy had last week. I have a 36 inch under counter oven. I use it all the time. I have had it for about 10yrs. In the last year the computer has been replaced 3 time. The first time it cost me $600.00. 6wks later it was replaced for free. Now the oven is having the same problem. I hope Dacor makes me as happy as Judy.

Purchased home with installed Dacor double oven. Oven wouldnt reach set temperature, so replaced control board. Doable, but a real hassle to remove oven from wall opening and label, disconnect, and reconnect 20-something wires. Two years later, the clock cannot take the correct time and oven timers do not work. Only fix: replacing the $300 control board again. I cannot recommend that anyone purchase these appliances as the control boards simply do not work for more than a couple of years.

We purchased a home with a 5 year old Dacor Discovery IQ Double Wall Oven. Model Number DYO230S. Great looking and it has a very sophisticated and functionally rich digital control system. Problem is the digital control system does not work. The stove has a mind of its own and will just shut off for 24 to 48 hours and return to function randomly. Shutting the power off and turning it back on has no effect. Dacor (Now Samsung) has been completely un-helpful. Bottom line response - tough. Product is no longer produced, replacement parts no longer in stock - maybe there is a part on eBay ** Honest that is the answer. I have called parts companies who also complain about Dacor (now Samsung). No luck. So we will now need to purchase a replacement product for anywhere from 4,000 to 10,000 dollars. To replace a 5 year old - 8,000 product. It will definitely not be a Dacor or Samsung product. And I will do my best to put similar reviews on the internet where ever I can.Just to add some balance - 21 years ago we custom built a home and purchased two Dacor ovens. Both were great. 21 years of flawless operation. When we saw this oven as we went through the home purchase process we were delighted. What a disappointment. Also - before the oven started to go wacky on us we needed to replace the bulbs (2) in the oven light fixture. Initially I contacted Dacor parts and had a very pleasant experience ordering the two replacements. However nothing came to our home. Called again and found that Dacor had been sold to Samsung and the price of the bulbs had doubled or more. No exaggeration. Stay away from Dacor and Samsung.

My Decor Epicurian oven and range has been a nightmare from day one. I have had the oven for about 8 years and had it repaired so many times I have lost count and had spent at least $2000 on repairs. We have experienced motherboard burn out, membrane failure, temperature control malfunctions, error messages that cause incessant beeping. Nearly all of the problems that have been described in this list of complaints, I have had the problems themselves multiple times! Now, I am panicking a bit because I decided to use the self clean function on my oven this morning and now, I have read some sad malfunction stories following the use of this feature. I am so torn about whether I should just cancel the cleaning process. I do not want to risk having the oven malfunction again, but the thing really needs to be cleaned.

I purchased all Dacor appliances when our home was built 3 years ago. The Refrigerator has been serviced 2 times already and now requires manual defrosting every month to keep it functioning. Now the double ovens broken! These appliances are expensive and a total nightmare...never buy them!

I have had nothing but trouble with a wall oven I bought in 2010. Basically just bad electronics. I finally replaced the oven in 2014 and had to get another Dacor to fit the opening. The new unit still does not heat evenly and is consistently off by about 50 degrees. Customer service is not helpful at all. Local repair shops cant really fix issues. Terrible company. Cant figure out how they stay in business.

We have a Dacor gas range RSD30R that we bought to upgrade our kitchen in 2002. We have had several issues with the range to date. The first issue we had with the range was the auto lock for the oven cleaning cycle that failed in 2007. It was not covered under warranty and cost $88. The second item to fail were the oven door springs. They also failed in 2007 and covered under warranty. They failed again in 2017 and had to be replaced for a second time. The springs are too weak to hold the weight of the heavy door. $68-$78 for the springs. The springs could easily be changed out as the brackets are still good but they only come as complete units. The last item to fail were the ignitors. Only one ignitor failed out of the four but as the spark module ignites all burners every time any one is turned on, premature failure could be expected as all ignitors light every time. This time the part is no longer available from Dacor. Dacor does not support any products they build after 7-8 years. Parts will no longer be available. I would not recommend Dacor Appliances to anyone as the manufacturer does not support their own products very long. I purchased Dacor to buy American and I regret it now. In contrast every product that Miele made even 20+ years ago, parts are still available directly from Miele and other suppliers as well.

My husband and I built our home and moved in November 2002. We purchased a Dacor Double Oven, Dacor 5-Burner Electric Cooktop and a Dacor Microwave. After the second year of living in our home, we started having problems with our double ovens. It would start beeping at different times. Sometimes it would last a few times to off and on for days. Then it would stop beeping and not return for a year. Now the beeping has started again and now it is displaying off. It wont come on. We have turned the breaker off and back on because sometimes that would reset it but not this time. Now before I could call anyone out to look at it, my 5 burner electric oven is dead. I called Metro in Tulsa, OK which is where we purchased them and they gave us the name of a repair person in our town. He came out and told us that we needed new boards for both appliances and charged us $50.00 a piece just for the evaluation. Now one week later, he is calling us and telling us that our 5 burner electric oven is discontinued! I dont want to have to purchase a new oven! I will also say that on my microwave, where the time is displayed it is blank across one line. I didnt even ask to have it look at. Please help!

We thought we bought a quality product when we remodeled our kitchen two years ago and put in a $3000 30 inch wall oven from Dacor through their dealer Friedman’s in Knoxville. We had heard for years that their products were top notch and high-quality. I find it interesting that the oven has a self-cleaning function. However Dacor Technical advised me that if you use the self-cleaning function you will create too much heat and destroy the motherboard. Wonderful input after the fact. The oven now does not keep a correct temperature and we are advised that our oven is two years old and out of warranty and we should not have used the self clean function. Really? Why is the button even there. Do not under any circumstances purchase any Dacor product. I feel comfortable in saying Samsung will add absolutely nothing to the quality or service. The lack of customer care and concern is beyond reproach. One star rating is way too generous. How do you just walk away from your products. We used our clean function exactly once and nobody ever said it was a self destruct button.

We bought our house in 2010 and our Dacor stove was supposedly newer. When I went to clean it, I found loose screws in the bottom. Apparently, the convection element is loosing its screws and washers. Ive had this appliance fixed once already when the cooktop kept clicking. The black plastic around the controls cracked mysteriously. It takes 3 hours longer to cook a turkey than it should. This is a strange stove, which supposedly cost a lot. I wonder if a convection part missing two screws should be used?

Updated on 05/12/2020: I wrote a review of our Dacor kitchen and gave the company a review of 2 stars because the cooktop, ovens, and hood blower all have failed at some point. The real issue is that the company doesnt support products after sale to quote them they do their best... The other problem is this site, it allows companies to claim they are or have resolved issues, without a response or comment from the customer about what the Companies Resolution entailed. Sending me an e-mail that says sorry the thousands of dollars you invested in our products only bought you up to 7 years of replacement parts, isnt what most people would call a Resolution. After months of working with the retailer and Dacor the e-mail below is what they consider a Resolution:Subject: Dacor customer service **Hello Mr. **, We would first like to thank you for staying a Dacor customer for as long as you have and would like to apologized for the inconvenience. As a manufacture we are constantly innovating products and at some point parts and units do become obsolete. Dacor does provide parts for as long as we possibly can. Once the appliance becomes obsolete we are only required to hold parts for up to 7 years. We again thank you for being a Dacor customer. Be safe during this pandemic. Have a great day. DENISE ** | Customer Service RepresentativeO: (833) 353-5483 x** F: (626) 403-3130Original Review: We built a new home in 2003 and purchased Dacor Preference appliances. Including a 6 burner cooktop, double 30 inch wall ovens, warming drawer, a microwave, and large hood with a remote blower. All the appliances are stainless. We enjoy home cooked meals and prepared at least one meal a day. Our kitchen is a work place not a show place. So these are my feelings after 16 years of use.The Cooktop has plastic knobs and a rubber gasket under each burner and piezo electric igniters. All of these items have failed over the years. I replaced the burners some years ago because when the gasket fails the burners sputter and liquid spills leak into the bottom of the cooktop. Replacement burners fixed the problem for a while but the burner design makes this a point of failure. Additionally, the burners were expensive so were back to sputtering burners and disassembly for cleaning. One of the plastic rings under the flame control knobs broke, weve ordered a new ring ($26) a couple of months ago but Dacor cant give us an estimated delivery date. For the past few years the Piezo electric starters only light half the burners, (they spark but the burners dont light) not a big deal but these are high end appliances, using a match to light the burners is definitely 1950s.The 30 inch double ovens are a great size for bakers like us. The Convection feature is great. However, the first time we ran the self cleaning cycle on the upper oven the door handle on the bottom oven bubbled and melted. The real issue with ovens today, is that Dacor has stopped making replacement parts including the electric heating elements. So even though we spent nearly $3,200 for these ovens, Dacor no longer supports them.The Microwave never worked correctly and we replaced it almost immediately. At that time Dacor used relabeled Sharp microwaves. Finally, Im not a fan of cooking smells in the house. So, we purchased 48 inch hood with a 10 inch inline blower. This week it failed. The motor hums but the fan doesnt turn. So replacement parts? Nope. If you decide to purchase Dacor be aware that the company doesnt provide support for their products in the long term.

We installed 2 Dacor wall ovens, a 5-burner cooktop, and a downdraft fan in 2000. The convection ovens bake perfectly and have performed without fail. After 7 to 8 years of daily use, we did have to replace the door hinge on the oven I use most often. We are in a rural area so the repairs are accomplished through Sears. The replacement parts arrived in a timely manner and the oven has worked perfectly since. The cooktop is easy to clean and the heat is even. The downdraft fan is effective and easy to clean. I would be confident to recommend Dacor products.

We purchased a Dacor Double Wall Oven in late November of 2019. I liked the oven and it functioned well until October of 2020 when the oven quit working due to a control panel issue. We were told the part was on back order. I continued to check with Dacor customer service and was continually told the same thing -- it was on back order. Never once did they call me to give me an update.In December of 2020 when I called I was told there was an update. The part was no longer on back order it was no longer in production, they no longer make the part. They would review the file to see if they were going to give me credit for the oven or get me a new oven. I contacted them again today and was told it was still under review and it could take them another couple of weeks to decide what to do. I asked to speak with a supervisor but was told that there was not one available. The person I spoke with today said that she would call me next week to give me an update. I appreciate her concern but that does not get me closer to a working oven. I would not recommend Dacor to anyone, customer service is terrible.

Oh how I wish I never bought a Dacor! It has been nothing but problems. I figured I bought a lemon but after reading other reviews its just not a good product with not very good customer service either. I have had repairs every year, and even after repairs it still isnt functioning as it should. The first problem I had was the whole glass window blew out during baking, which seems to me is a huge liability. The company said that shouldnt happen but is out of warranty and would give me a discount on the glass. I thought that was better than nothing but then 6 months later the relay went out, then baking temps were all over the place in the oven so they said I needed a new motherboard and they said both ovens needed it. So those were repaired. Oh ya and the light in the bigger oven hasnt worked past the first year even after having the light changed and some electrical stuff done on it. Then I had the bulbs changed due to irregular oven temps. The temps are still all over the place to this day.The back right corner gets too dark. The front left doesnt brown and is a lower temp. Now Im having problems with the oven turning off during baking and when using broil in the small oven it causes the large ovens probe alarm to go on and offer at least for an hour. Dacor didnt help me with anything past the glass and its only been 7 months since the new motherboards were put in. I cant afford to buy a new oven at this time and so I only use the small oven mainly since the larger has so many problems. Do yourself a favor and never buy a Dacor!

We purchased a Dacor Epicure dual fuel range when we built our house 7 years ago. It was the most expensive appliance we bought and we wish we hadnt. We have had no problems with the stove top, but the oven, specifically the broiler unit has been a consistent problem. We rarely use the broiler and use the oven perhaps 2 or 3 times a month. Yet, the igniter had to be replaced in March of 2008 and again, in June of 2010. In January of 2011, the broil gas valve was changed and now in September, the broiler is again not working. I cant see pouring any more money into this appliance and will sell as soon as I find a buyer willing to take a chance on it. We have been greatly disappointed in this product.

I went to put something in the cabinet at the top of my built-in wall oven and noticed the cabinet door was warm. Then, I noticed the heat was coming from the top of the oven at the control panel. I am afraid of a fire breaking out in the cabinet now. The oven is less than a year old. We just remodeled our kitchen and installed the ovens in May 2012 and this is just June.

I purchased my Dacor range in 07. After running the self clean cycle today, my oven wont heat up using convection or regular bake. Keep in mind, I had the entire electronic guts of the oven replaced in March 2011, 6 months ago after the same full failure. I paid $6,500 for this appliance. I wish I had my old GE oven back. This piece of equipment is only 4 years old. My husband and I dont use the oven often. What a huge disappointment! I will likely spend the next few days on the phone with customer service.

I purchased a column, panel ready fridge and freezer. There was a promotion for 10% rebate, which took me 3 months of emails to obtain and they only issued a partial rebate even though I supplied them with proof of purchase. The service was dismal. The app for the cameras and interface with the appliance hasnt worked the whole time I have had the units. They look pretty and work ok as far as cooling, but for the price they charge they should provide exceptional customer service and being that Samsung owns them you would think that the app would function.

This is our second Dacor wall oven. It is approximately 6 yrs old. December 22/14, I was cooking a Christmas turkey as per usual, and I noticed an odd smell about 40 mins. into cooking. Checking the turkey, the temp. was at 500 degrees and on broil. I burned holes in my oven mitts on the roaster taking it out. Even though I set the temp. at 325 convection roast, it reset itself to 500 broil. Nothing works except the clock. Called repair guy after the holidays. Said it is a control panel behind the keypad area. Ordered the part. Been waiting 4 months now for this part. Now, no Easter dinner either. After reading these complaints, I am worried that this part replacement may not be the end of it.

Our new ranch has three Dacor microwaves, only one of which has had a few months of use. The others have very limited use. To this point weve not had problems, but given the opportunity to redo the purchases wed go with a popular brand, i.e., LG, GE, Panasonic. They are more flexible, parts are available, and all three combined would probably cost less than one of these. In fairness, I personally feel the same about our other high end appliances, Wolf, Viking, Sub-Zero and Asko. None beats our former appliances. Maybe its just about show.

I purchased a Dacor Black Dual Fuel Range (RSD30B) in 2001 which was installed during a kitchen remodel. We moved back into the house on 12/24/01. We hardly ever use the oven because my husband barbeques every night. In less than 5 years, a piece of the plastic front control panel fell off. In early 2008 the self cleaning function broke (error F2). I called Dacor and they referred me to a repair service. It was going to cost almost $500 to repair so, given that we use the oven so little, I decided not to spend the money on an oven that was falling apart. Now within the last two years the plastic control panel is cracked across the front and more pieces are starting to fall off. Now the clock and the timer have stopped working. I called Dacor again today and was told that the seals and hinges on the oven are probably bad, which is contributing to the problem. The customer service person was rude and unhelpful. He said it was not unusual for a ten year old oven to break. He gave me contact information for a parts dealer and two repair services. I bought this oven believing it was a high quality and I expected them to stand behind their product. What can you do to help me?

I purchased a DACOR PGR-30S LP in 2002. It has had a number of problems due to poor design that required replacing the control panel as well as other parts. However, it has recently developed a gas leak and thus is no longer usable. To fix the gas leak, you must take off the top burners to get to the leak and make a repair. UNFORTUNATELY, DACOR has to make room for new parts and no longer makes the O-Rings required. Yes, apparently a $10 O-Ring takes too much room seven years after I bought my range. So, in 2009, DACOR discontinued making the O-Rings and now I have a very expensive paperweight that I have to take to the dump so that I dont blow up my house. I wouldnt ever buy a DACOR again. The customer service it terrible and they cant even be bothered to carry simple repair parts. Buy a Wolf or some other high end stove because DACOR is literally a piece of junk!

I bought a Dacor dual-fuel range in 2002 for my new house. Within 18 months, the control panel on the front had shorted, causing the stove to emit a continuous beeping. I got this repaired, and was advised that I should not use liquid cleaners on the stove! Two years later, the same thing happened again. Finally, about 4 years ago, another fault developed in the 3rd control panel, the circuit controlling the oven lights will not respond to touch, and the oven lights switch on and off continuously. Not prepared to pay for yet another control panel replacement, I switched off the power to the stove at the main fuse box. I have continued to use the gas cooktop only, lighting it with an ignition wand. The Dacor stove is only part-functional due to what is obviously a severe design fault in the front touch control panel, which causes the panel to short. I switch on the power to the unit twice a year to use the oven at Thanksgiving and Christmas for large roasts. This stove was a very expensive mistake. Luckily, I have a second (Wolf) oven in my kitchen, which I use instead for everyday cooking.

Dacor dual fuel 30 inch range - First of all the look of the dacor is second to none in my opinion. The digital screen with blue lighting makes this a truly elegant part of any kitchen..... when it works. The range top itself worked flawlessly for me and the main burner was always more than enough. The problem with the range lies in the electronics. The unit has been in my home for over a year and has worked for less than a month total. An error code appeared when ever the oven gets hot. C33, C1, 0000, 1111, C11. Ive seen it all. I have had the main board replaced twice and my local repairman is on first name basis with even my dogs at this point. The final straw for me was when the oven door glass shattered while cooking and when dacor was contacted they said that happens. Im think Ill try Viking.....

Warning: Warning, safety hazzard for all, adults and children. Recommendation: The knobs should be set on the top of the stove, not the front where children can reach. Control knobs should click when fire and gas is turned off, and highest flame setting should be at the end of the turn just like a clock. I inherited this range as new owner of the house. Today I used the high flame option of the gas stove. When I was done with cooking, I turned off the gas according to the knob position, front of the turn. Later I discovered the range was not exactly off. It was still hot but no flame could be seen.I checked by sight the control knob position, it was set incorrectly in off. Then I touched it and realized the knob actually has a bit more to go to the end, slightly before the off position. Therefore it continues to release gas with unobservable flame. This knob does not click when user turns it to the off position. It is just a silent knob with an inaccurate cue of a heavier black line for off and on indication. Besides, high flame setting comes at the beginning of the turn of the knob rather than the end, it is counter intuitive to our mind of increase heat by turning the knob further on, like our clock. Oven racks are hard to put back after cleaning. Once a rack almost tumble out while food was sitting on it.

DCT305SNGH - I have owned this stove for about 3 years already. From the very beginning it has been trouble. The lights that turn on when a burner is on broke immediately. The place where the gas comes out and ignites is black and hard to clean. The grates are rusty, the finish has come off. The indicator knobs dont reflect what is happening in other words if it is on the lowest setting you dont have any indicator marking. It is hard to clean and scratches very easily. I have had the service person out about 5 times until they decided to send me many new parts. These arent any better. It is just a bad product. Basically the warranty is useless if you keep calling for the same issue. They say, This is the last time we will fix this issue. Sadly I always heard this was a great company and I waited 7 years to save up for this stove and boom rotten appliance.

In 2008 I had the luxury of choosing kitchen appliances for our new home. I looked at them all and felt Dacor was the best choice. Choosing Dacor for our kitchen was the worst mistake I have made in kitchen appliances in any house in which I have lived (and there have been quite a few). The oven (48 dual fuel range) didnt work from day one. There was a problem with the temperature control. The oven would not shut off when it reached the desired temperature. Disappointing, but I told myself that sometimes things can go wrong and it should be an easy fix. Well, many service calls later and several re-wires of the unit, along with the installation of many new parts, the range still does not perform as well as the worst oven I have ever had.There is a tool that comes with the range that is used for taking the top off the unit to access the wires. My range was taken apart so many times that the tool wore out and had to be replaced. The front piece of the range no longer fits flush with the rest of the range. On one of our last service calls, I was told by the serviceman that Dacor said that under no circumstances would they consider replacement of my obviously faulty, beyond repair range. Eventually I got tired of repeated service calls. Sometimes servicemen would come out and say they didnt know how to fix it and leave. I would not expect such poor customer service from an entry level company. From a company touting themselves as a manufacturer of top of the line products, I would expect a greater desire to stand behind their products.The oven still does not work well. On convection bake, I must turn cookie sheets around or I will have doughy cookies on the same sheet as burned cookies. And forget using the convection setting to bake 2 sheets of cookies at once - it takes longer than baking them separately. I wish I could attach a picture! I also chose a Dacor microwave and refrigerator. One of the salesmen I spoke with about refrigerators said to make sure the unit we select did not have air transfer between the refrigerator and freezer, and the Dacor model did not do this. Well, when my 48 side-by-side arrived, it had the air transfer. I was disappointed but chose to live with it. Of greater concern to me is the noise the unit makes at times - sometimes loud enough I can hear it in other rooms of the house. I have not bothered to call for service. Im not interested in another fight to get Dacor to stand behind their poor quality overpriced products.At this point, I have no expectation of Dacor standing behind their products. I just want to share my experience with others who may be in the same situation I was - designing their dream kitchen - and save them the regret and continual disappointment in their Dacor products.

Don’t purchase Dacor appliance - it’s been worst purchase experience ever and I am extremely disappointed. After six months since I purchased the Dacor built-in refrigerator, Dacor couldn’t even ship the proper installation parts and my refrigerator is still not working. Problems:1. Their high end $11K Dacor built-in refrigerator cannot even be installed. Wasted five months communicating with both Dacor and the retailer AppliancesConnection. After five months they were still able to ship the proper missing installation parts. Over the past five months, I talked to six different team members in Dacor customer support team, escalated to customer support lead and also talked to their regional technical manager, none of them is able to solve my problem and ship the right installation parts.a) Their process is extremely messy. Their customer support team had no idea about installation requirement of the refrigerator. And the request from their customer support team is declined by their internal Parts department again and again, only to find out installation parts should’ve shipped by the retailer. This is extremely confusing now and no one in the team seems to understand the right process.b) After Dacor acquired by Samsung, their manufacturing process is very messy and parts are extremely confusing. There’s one version of required installation parts in Dacor manual and one version of Samsung parts in the Parts guide, and no one in the team seems to understand the difference and how to map from one to another (they insist on sending me Samsung parts instead, claiming they’re compatible). I am now the expert myself to understand all their parts and able to identify many problems in their manual.2. As a high end brand, Dacor doesn’t seem to care about their customer at all. As a customer who did kitchen remodeling and had no refrigerator to use for five months, no one in the team seems to care about their brand or their customers. With this huge gap in the process, no one thinks about the problem from their customer’s perspective or shared empathy with me. Dacor as a brand is really bad and I am extremely disappointed in both their product and services.

Dacor 27 electric double oven unreliability. Almost from first use the Dacor electric double oven has been plagued with problems including but not limited to door not locking when self cleaning, not self cleaning, door not unlocking upon completion of self cleaning, and filter issues. Since purchased in 2013 the top oven has been used between 75 and 100 times; the bottom oven less than 25 times. Yesterday the oven died. First error message U43 relay board. Second U60 cooling fan. Worse when the control board responsive/froze circuit breakers were needed to turn oven off.Repair estimate is $1600 plus tax. I intend to replace the overpriced and unreliable Dacor with a Kitchen Aide at approximately 13 the price based on customer and Consumer Reports reviews plus a new one year guarantee. I do not recommend the Dacor double oven if you are a serious cook and/or frequent user. Brand name and styling are less important than product reliability and useful life especially when you can purchase the former for two-thirds less money.

Bought the DACOR WALL OVEN in late 2019. Top burner is over heating and burns everything, caused a fire in the oven. Can not even get any response from customer service. Warranty not worth the paper it is printed on. Stay away from DACOR.

We purchased a Dacor built-in refrigerator in 2011. After just 5 years the warning beeper came on. We learned that the main control panel - built by Whirlpool - was defective. We then learned that Dacor did not have any replacement part for this model. Our only alternative was the purchase a new refrigerator. Amazing!! Dacor reluctantly gave us a partial credit for a new (KitchenAid) model. However at the end of the day we are out of pocket over $2000 because Dacor built and sold a defective refrigerator with no ability to fix the problem. Very unsatisfactory handling of this situation.

About 3 years ago, I spent almost $5,000 on a Dacor double oven. We had it less than 3 months when the motherboard had to be replaced. About 3 months ago, I started to get various error codes and a continuous beeping. An authorized Dacor service repairman has replaced the motherboard three times. He was on the phone each time with Dacor, however we still get the error codes and Dacor has told the service repairman that they are stumped and dont know how to fix it.Here I am, having a beautiful expensive oven to look at but was unable to cook a turkey for my family yesterday! It seems that there is a major error in this oven, and I am stuck with a huge repair bill and an oven that does not work. I can only hope that Dacor will step up to the plate and come up with a solution or replace the oven which obviously is a lemon.

We purchased a complete kitchen with Dacor Modernist stainless steel look. It has been a complete disaster since install day. The first week the Dishwasher flooded my kitchen causing water damage to my brand new kitchen cabinets. There was a seal issue. My ice machine has been worked on 6 or more times. They have replace every part in it and still doesnt make ice or if it does it freezes in to one big block of ice. My microwave combo oven just broke again today with same error code as last time. They had to replace both motherboard in the oven and microwave. Tomorrow they are coming because my dishwasher never completes a cycle. It shuts off at 16 min left. I have been asking for replacement units or better yet take it all back...I would not recommend Dacor espcially how much we paid... over 30,000.

We were out of state from December 21, 2014 to January 2, 2015. The condition of the refrigerator was discovered at about 9:30 PM on Saturday, January 2nd. Upon opening the door the Dairy Compartment Cover fell to the floor. We could immediately see the damage but did not know the source. As a result, the unit was turned off. The owners manual was consulted along with a review of the Dacor website. The office was closed on the weekend so Monday was the earliest we could obtain names of Dacor authorized repair agents in the Phoenix area. A authorized Dacor repair technician stated the light switch or light circuit in the board failed. The interior light bulbs located at the top of the refrigeration side of the unit remained on when the refrigerator door was closed. The heat generated by the continuously lit bulbs led to the melting and charring of the plastic light fixture. The light socket melted, the wiring harness melted into the socket assembly, light switch, and control panel. The heat was intense enough to warp the Dairy Compartment clear plastic cover, some of the adjustable door bins, and the interior door liners. Also, all food containers made from plastic such as salad dressing bottles, mustard, ketchup and mayonnaise, etc. were disfigured. Of course all the contents from both the refrigerator and freezer had to be disposed.Before leaving on an extended trip we had been following the instructions preparing for a vacation listed on page 19 of the owners manual. On our departure date the food that would not have lasted more than two weeks was removed from the refrigerator. The ice bin was emptied and the wire shut off arm was raised to the OFF (O) position. Note, page 19 does not mention to set the Sabbath mode when leaving for a short or long vacation. We were fortunate that the damage was contained within the refrigerator.

I had an issue with the wall oven light on my Dacor Preference double oven. To make a long story short, after contacting Dacor directly, they made sure that the unit was fixed by providing the part directly to me and confirming that the local repair company would be willing to install it. The oven is 8 years old and in the end, what I spent seemed reasonable to get a fully functioning oven (membrane switch). They were prompt, personal and courteous in their response to me. I came away feeling that Dacor takes pride in their history and their products! They also cleared up some misconceptions that I had regarding the status of their company. Although it was frustrating to have an appliance not work properly, I feel that the customer service Dacor provides makes their company one worth sticking with. That makes a big difference in todays impersonal world.

We just purchased our home in March of this year. The previous homeowner purchased a Dacor oven; it is electric & propane. She purchased the appliance after a complete home renovation in 2008. They lived in the home. After 1 year, they moved out and had it on the market. We purchased the home in 2012. As soon as we moved in, we noticed the oven was not working. We called an appliance repairman - $564.00 service call and part for a new relay switch. It was great; the oven worked. Not even a day later, an F1 error. We called them back out thinking they must have done something incorrectly. They then said we needed a new control panel. We did not have an additional $400.00. We just moved, so he said you could still use the oven. We did. We would use it and flip the breaker off so we did not have to hear the annoying beeping sound. Then I came home and bam - no display, no oven. We called a different Dacor certified appliance guy thinking the first company was just taking us for a ride and it was their fault. $572.00 later, we got a new control panel, but guess what, the technician did not even make it to his truck before beep, beep, F1. He came back in and then said we needed to replace the display screen - an additional $217.00 with no labor charge. We told the man to shove it. I had every plan of taking the oven to our back tank and using it for target practice. But in good business practice, since this company already invested $572.00, we could not ask them to eat the money, so we allowed a third fix of the oven. While the technician was here, the oven made a horrible loud sound and shot out flames. He insisted maybe it was due to it sitting for a week without use. He left. I never noticed this flame before when the oven worked despite the F1 beeping. Now it’s hit and miss. Some days it will shoot out a flame once until it reaches 200+ degrees and then you can hear the fan kick in. Some days, twice, I have had it happen 3 times. If my children were to open the door during this event, I am sure they would be seriously burned. At first I was thinking maybe it is normal for this oven to shoot out flames during preheat mode since after $1300.00 repairs maybe it is just not functioning correctly. But if it were a normal function of the product, to me it would do it every time consistently and not three times, or two times on some occasions. I hate to admit this but I am almost fearful of using my oven. I currently have a pie to put in for dinner and I’m thinking its 3:09 pm; I could set the oven to preheat while I run to get my kids from school so if it decides to blow up, I am not home and that is pretty sad. The last repairman we had come out said in his personal opinion, he wouldn’t have repaired the oven, because they are known for issues, and he would have gone to Lowes and spent $300.00 on any off brand stove first. We have considered that, but this stove is extra-wide and the cabinetry is built around it. So for us to purchase an oven to slide right back in it would be another $1300.00-$2000.00. We have issues with the burners not always wanting to light. I almost caught on fire lighting one because it shot out flames when it decided to finally ignite. Sometimes it just clicks. Currently, I am down to two burners when just two days ago all six were working just fine. Over Thanksgiving, it took no kidding 1-hour to cook brown and serve rolls because the oven did not reach the set temperature. We stuck my husband’s bbq thermometer to see. It was 256 degrees, not the desired 350 degrees. Does this stove have warranty? We have no clue as the previous homeowner purchased the stove. She claims to have spent $5,000.00 on this stove or more during their purchase. We do not have warranty on our home so for each repair, it is out of pocket for us, and currently we really are thinking any knock off brand at Lowes would be a better product than a Dacor oven and less of a safety hazard for our family.

Most of my life, Ive always bought pretty low end appliances, and theyve always worked pretty well. When we remodelled our kitchen, we decided to go with a high end Dacor stove, and its been nothing but trouble. After just a few weeks, the igniters started to fire constantly on some burners. It was still under warranty, but it was very hard to find someone to honor the warranty. We got that fixed, then the oven light started to come on and off randomly. After our experience with the first problem, we just disconnected the light and let it go. A few months later, the bottom shelf jammed, and there was no way to collapse it to fit in the oven. This product is total junk. Dont buy it!

I purchased my 30 range and was so excited! Well no longer. First the wrong range was delivered. I had to wait another three weeks for the correct one. My oven can not cook at all. Temp fluctuates by 100 degrees. Going on my third service call and still not working. It very unfair, I have to take time off work to wait for repair person, then nothing is fixed. I wish I could return this lemon. But after reading other reviews I am not alone. Why is this company not accountable for ripping hard working people off. I love cooking. Its my passion. My Kenmore Elite was half the price and far more superior.

I purchase a home with a Dacor double oven. Unfortunately the oven begins transmitting multiple beeps and the touch panel will sometimes read off after beeping a while. I contacted the staff at Dacor requesting a service manual. They refused to send me a service manual and stated that only authorized technicians can service their equipment. Its obvious they used google or a local phone book and sent me contacts of appliance repair shops in my area.When I called, they had never heard of Dacor let alone be factory authorized. I called Appliance repair shops up to 50 miles away to find there were no Dacor Dealers. I found one 70 miles away but it was too far to send a technician. If I remove my oven from the wall and take it there they would attempt to look at it. I had to reverse engineer the thing to find that my touch panel has gone bad and now I cannot find a used one. I want to recommend that anyone considering an appliance DO NOT PURCHASE A DACOR! If you are looking for high end stick to SubZero / Wolf. Oddly enough I see that there hasnt been any reviews for the past 5 years. Maybe it appears people have stopped buying Dacor appliances.

My Epicure dishwasher is being replaced after 4 years of use. The racks are rusted. It leaks. And the spray arms are broken in two. The dishes need to be completely washed before putting in dishwasher. Do not purchase Dacor dishwasher.

In 2013 we remodel our kitchen. I need a 30" stove and Dacor seem the right fit. I had problem with the igniter burning on that stove and some metal warp as well. They replaced the stove in 2015. I smell gas every time I turn oven on. Last Thanksgiving 2019 the stove stop working. I was told the igniter had burned out and had it replaced. I had repairman come twice because of smell and end January 2020 the stove stop working again. The repairman told me that a jet burner assembly was never installed this is why I smell gas after it is turn on. ** They said they will order the part. It's back order So I contact Dacor. First they told me it's back order then give me a supplier. If it was never installed in the unit shouldn't Dacor take care of it and soon.

Dacor refuses to take responsibility for defects in their products. Our wall oven required two cooling fan motors and two relay boards over a relatively short period of time. In addition, all of the sensors had to be hard wired when the oven stopped working, and our service technician was informed by Dacor that moisture tended to get into the sensors on these ovens. We spent nearly $1500 on these repairs. Reaching a customer care representative at Dacor can take upwards of 20 minutes. Phone calls are not returned. Customers are left to pay the cost of defects in Dacor products.

After purchasing what I thought would be ovens of a lifetime I could not be more disappointed, frustrated and angry at a company in my buying history! Since November of 2014 and longer I have been fighting for service or answers or at least honesty! The ovens have never worked properly, they do not keep temperature. The oven temperature drops 60 to 75 degrees while cooking over a couple hours. The control board was replaced. Still the ovens never worked. If you like to cook and cook for the bed and breakfast, which is why you bought an oven like this, you will have your ovens on for a couples hours preparing any multi-dish meal! I was treated rudely on the phone during routine troubleshooting and was never allowed to speak to a manager. Dacor for months or so later is buying back my ovens minus a restocking fee, on ovens that dont work, $1200!

I replaced my Thermador Wall ovens with Dacor because the size and I would have to do less retro-fitting of my cabinetry, this was a grave mistake. Here are the issues with Dacor.1. The high heat sensor trips and you need to call a service professional to have it reset. This gets very expensive. I have tripped mine three times, once baking a cake at 350 degrees, once during self-cleaning and another during normal cooking. The Dacor Service Help said this was a common problem because the heat sensor is located near to the touch panel.2. The oven vents from the bottom of the unit into the room heating my kitchen.3. The glass window does not seal so I have stains in-between the panes of glass. Not very attractive to stare at large drip stains.4. It takes an exceptionally long time to pre-heat oven and convection mode even longer.5. The temperature cycles through and does not maintain its cooking temperature causing underdone results and longer cooking times. This is especially challenging when cooking roasts and large turkeys because they may take up to an hour longer than expected.Overall, I do not recommend this product.

When I pay top-dollars for a supposedly high-end product, I would expect performance and durability. That is not the case with Dacor. This manufacturer charges top-dollars for their appliances but their products do not live up to expectations. I purchased a Dacor gas cooktop range, and within a year several blue-indicator lights on the knobs (which indicate the gas is on) failed. At that time it was covered under warranty, and even then it was a hassle to get the repair technician to come out and take the range out to get to the electronic parts. After replacing two of the lights, the other lights failed as well, and then the replaced lights eventually went out. Now, only one out of the five lights work. After a year, the appliance is no longer under warranty, and it is too expensive to get it serviced. Its not only a cosmetic issue, but a safety one as well.Were in the market for a single wall-oven, and I considered a Dacor for its clean and stylish design. However, after reading the reviews about Dacor, Im veering away from this company. Sadly, as much as I want to support a Made in America company, the pride of workmanship and customer service doesnt live up to this companys branding.

We purchased our fridge for $9,249 in September of 2016. By the beginning February of 2019 the fridge stopped working completely, I called Dacor who sent out a technician to determine the problem. The technician said the compressor had failed and needed to be replaced. A week later we found out that Dacor no longer makes the particular compressor I need. I have now been living without a fridge for 3 weeks and Dacor doesn’t seem to care at all. We have 3 children and are currently living out of a cooler with ice. I call them and email them every day begging them for a resolution. They are a avoiding me. I believe they owe me a new fridge and they don’t want to do it. We saved long and hard for our expensive appliances and it’s absolutely heartbreaking to have this useless fridge stop working after 2 years, and Dacor seems to not care.

Dacor Double Oven Model D0230 - I have had my oven since November 2011. I purchased an extended warranty at the time of buying the oven. Right after it was installed, I called and said they needed to come and adjust the temperature control. It was off at least 50 degrees. It never held the correct temperature. Since July, we have had to replace 2 relay boards, two other parts that should take care of erratic temperature. Then I noticed the gasket was turning black in the corner and my glass pack in the window was steaming up and not clearing. The extended warranty would not cover the glass replacement and I was charged $126. They said it was cosmetic, but this was so bad that I couldnt see through half the glass. The steam stained the glass and you could not clean it, because it was inside two pieces of glass. Do not buy a Dacor oven. In 38 months I have so many repairs that I have lost track.

This week Dacor installed my 2nd replacement gas range. I remodeled my kitchen 3 years ago and chose Dacor because I had a great experience with their appliances in the past, had their oven and stove in my kitchen for 15+ years and never had a problem. With the first new range, the oven started to automatically shut off due to excess heat escape, so the safety feature would kick in and shut the system down, in addition the knobs would become very hot even when the over was used briefly, 12-15 minutes. I was very impressed and happy with the customer service through Dacor, they immediately gave me a brand new over. Exactly another year, the new oven had the same problem, door begins to not hinge properly and heat begins escape, knobs get dangerously hot.This week Dacor very kindly, replaced my appliance with the new Dacor Renaissance 36. I used the oven for 12 minutes on 400 and the entire exterior is dangerously hot. I do not have any children, however, if I did I would be terrified that they could seriously injure themselves. The exterior of an oven should not become hot like this. Has anyone else had this issue with Dacor? I feel they have been very responsive with regards to customer service however I want an appliance that is safe.

Replaced a prior pro style range product with 36" all gas Dacor range and couldn't be happier. The styling is outstanding and the cooking performance is far superior to prior range. Simmer burners are amazing and convection roast is absolutely outstanding. Great product and experience!

I could have written every one of these negative reviews. Ive had all the same issues with my Dacor Epicure oven. Faulty computer panel, failed motor in the downdraft fan, oven not maintaining temperature (meaning NOTHING cooks correctly in this oven), burned out lower element and discolored interior. And let me add that the interior oven fan stays on for about half an hour after you turn off the oven. What purpose could that possibly serve???? Suffice it to say that this is a poorly made product by a company that has no desire for repeat customers. I am currently working with customer service to try to get my oven working for Thanksgiving, but I just dont have much hope after reading all of these similar issues. Clearly, they manufacture a sub-standard product and sell it at premium prices. Nice business model, for a while.

The Discovery Model 30 electric wall oven - After 6 years, the oven failed. The fan motor went out and at the same time, we were advised by a very reputable appliance repair recommended by Dacor that we need to also replace the computer or brain. Total cost of repair: $1150 with a warranty of one year.

I completed a 7-month total remodel of our kitchen and family room, which were connected in November 2007. The kitchen remodel cost $18,000 for various Dacor appliances including the Millenia series of wall oven MOV130S; warming drawer MWDV30; and 42 island hood DHI42130. The remaining includes the huge 30 Epicure dishwasher ED30SCP, 36 cooktop EG366SCH, and beverage center EF24LBCSS. All have the beautiful copper accent package and make for highly attractive appliances. We constantly receive accolades for them. If only they werent absolute garbage functionally and reliability-wise. Others have remarked how the ignitors on the cooktop continually spark, even after the light off. After contacting Dacor and waiting 2 weeks for the repair, for which Dacor sent the wrong part and caused another 2-week delay, the repairman had to rip off the front accent lip of the cooktop to reach the base which significantly dented the front lip. The ignitor worked like a champ for 2 days, then click, click, click - constant ignitions. So I cleaned around the ignitor tip with 409, dried it and it worked flawlessly. Thanks Dacor for your own product ignorance and my now dented cooktop. It has worked well since and is a sound product, so far. If only my luck held out.Next, the wall oven. Very beautiful and my control panel has held out (fingers faithlessly crossed). The oven isnt calibrated though, so follow cooking directions at your own risk. This oven will burn your food if you set the temp and timer to the recommended settings. I have to take off 25-50 degrees and 5-10 minutes of requested cook time or I will smoke any meal. After 2 years of use, I decided to use the cleaning cycle - following the directions to the letter. Forty five minutes into the cycle and kaboo! The front window shattered. Dacor says $700+ for glass replacement; I say send me the part and Ill do it. I got the discounted part for $68; spent 3 hours cleaning and reassembling with care; and the window has held, but I havent tried the cleaning cycle since. Why roll the dice again?Ah, now my fave garbage Dacor appliance - the interminable dishwasher. Truly engineered by the diabolical. I just completed my fourth major repair after 5 years of use. First, the drain valve failed after a few months of use causing flood and was replaced under warranty. Then the door seal failed (more flooding) and was also repaired and replaced under warranty. The dishwasher stinks, by the way, as the unit cannot evaporate effectively during drying cycle due to ridiculously poor rear venting design. So I have to leave the door wide open for hours after use to facilitate drying and stench reduction. The control panel/circuit board has fried twice now in the last 3 years - it just starts erratically beeping and refuses to take input, even with a power reset. Both technicians stated the design and quality of the board is third world, which likely is exactly where Dacor outsourced the garbage.The island hood and warming drawer have worked well, and the beverage center has been reliable but maddeningly causes back left cans of soda to freeze and explode occasionally; even with the set temperature raised to now 45 degrees. Fun to clean up after coming home from a long trip. My expectations are so laughingly low now for these Dacor products that I dont bat an eye with the frozen soda muck this fridge occasionally produces. Customer service though has been helpful and thankfully, American. They have replaced both circuit boards for free well out of warranty. I have only appreciation and great sympathy for the customer service folks who Ive spoken with. I love my kitchen, but hate the appliances in it. Never again Dacor. Never again.

Warning! Do not buy Dacor appliances! We have had our appliances for three years now and all of them have had something wrong with them. Oven circuit panel went and had to be replaced! Dishwasher arm and seal broke and dishwasher leaks! Refrigerator freezer compressor went! Hood range switch broke and had to be replaced! Dacor is the worst appliances I have ever bought! Buyer beware!

In 2008, I purchased my dream home and had the opportunity to build my kitchen from scratch. At the time, I shopped Viking, Sub-Zero, Wolf, and Dacor. I made an appointment to tour the Dacor showroom and was blown away by the aesthetics and advertised performance of their line. I made the decision to fill my kitchen with Dacor products: dishwasher (ED24SCH), dual range (ER48DSCH), range hood (EH4818SCH), fridge, and microwave (DMT2420). To date, the fridge is the only appliance that has not malfunctioned. Within the first month, the microwave blew a fuse (covered by warranty). Within the first 6 months, the dishwashers motherboard blew (also covered by warranty).Since the 1-year warranties have expired, the range hoods electrical unit malfunctioned and ceased working properly ($400-plus in repair). The motherboard on the dishwasher has gone out twice ($1200-plus). The dishwasher rack has completely rusted and the wheels have fallen off ($800 to replace). The lights on my oven dial is out and the glass bottom inside the oven that covers the heating element has cracked (nothing has been spilled or dropped). In fact, I only use that side for Thanksgiving. I am extremely bummed (to say the least) and I feel that the products that I was sold do not live up to the quality level that they advertise. Additionally, the replacement parts are obscenely expensive, and at this time it makes more sense to replace the units rather than dump more money into a pit.

I purchased the Dacor panel ready refrigerator and freezer column 15 months ago. The refrigerator stopped cooling -- in 15 months! These were 8k each!!! It had now been over 2 months without a working refrigerator and no end in sight. I will never ever purchase one of their products again! They replaced the compressor and 3 days later it stopped cooling again. What a joke! DO NOT BUY DACOR!

I have a Dacor 27 inch wall (model EOR) oven which I bought 2 years ago, along with a micro and a warming drawer. Since then, the control panel has been replaced twice. Both times because, after using the timer mode, the beeper would come on at all hours of the day and night. In both instances, I had to cut the power to the oven until the replacement part arrived. I am presently waiting for the third panel to arrive. Today I needed to bake something, so I turned the power to the oven back on. Now it will only function at 350 degrees and only in the bake mode. No other numbers can be put in and nothing happens when I select convection. So far Dacor has absorbed the cost of the parts and repairs, but that does not mitigate the hassle of having to wait upwards of 2 months for a part each time this happens.

Updated on 01/25/2021: After my review in December of 2020 I have continued to fight for a resolution with Dacor. Dacor appeared to be unable to resolve the issue and sent the issue to parent company Samsung. Samsung set up an appointment for repair then cancelled it saying parts were not available and that they would authorize a refund. I supplied the invoice and filled out all necessary documentation, including my banking information so they could wire the money. Today, a Samsung representative called and said I needed to talk to Dacor to finish the process, even though I was told everything was approved.I called Dacor and to no ones surprise they said this would have to be approved and only one person can make that decision and they are hard to get in touch with. Oh, and by the way, 10 days ago the second oven failed. Yes, the large oven that did not work when I purchased the unit. It was repaired in September and has already failed again. I now have a double oven Dacor range and neither works. This week begins my 10th week of fighting with Dacor for them to honor my warranty (again the unit was installed in August 2020) or refund the purchase price. At this point the range has been out of commission half the time I have owned it. I strongly suggest you heed the warnings here on this site. I wish I had listened.Original Review: On August 3, 2020 I purchased a 48 Dacor Gas Range. It was installed a couple of weeks later and the large oven did not work. It took better than a week for Dacors authorized service company to come out and diagnose the problem. The parts took another week to be shipped and then another week to have the repair made. It was a defective thermostat that was preventing the oven from igniting.Fast forward to November 24. In preparing for a big Thanksgiving, we turned on the small oven, only to find that it did not turn on. It had the exact symptom as the large over and would not ignite. I reached out by email to the agent at Dacor who had worked with me before, only to receive the below response: Thank you for contacting Dacor – We are no longer able to provide support by e-mail. Please contact us at U.S. Toll free: 833-353-5483 we are happy to provide personal support.Now begins the worst customer service experience of my lifetime. After opening a case, I have now talked with a dozen different agents and have yet to receive a resolution to my problem - a range that cost over $7,000 that did not work out of the box and has now failed again in a three-month period. I have spent hours on the phone and on hold and was eventually directed to Samsung on December 9 because Dacor could not get the parts. Samsung promised to refund the purchase price of the product is the parts did not come available by December 16.December 16 rolled around and now Dacor is saying that Samsung made the promise, but that they are different companies. Remember, Dacor directed me to Samsung and Samsung does own Dacor. I have been told that the parts for my oven are no longer available. After continuing to push the issue I am told that it is now in management review but that it may take 2 weeks for a decision on my case. It has now been nearly a month since I opened the case and I appear no closer to reaching a resolution on my failed Dacor range. I have asked to speak with a manager, but I keep being told this is not possible right now.I do believe that Dacor is in breach of their warranty. I have been more than reasonable in allowing them to remedy the situation. Since this was installed just over four months ago, it has been out of service in one of the two ovens for a total of 7 weeks. For anyone considering the purchase of a Dacor appliance, I strongly caution you to read the reviews on this site and other sites. If you are lucky and get an appliance that works and never fails, you might be happy. If you ever have to invoke your warranty you will hate your life. I regret that I did not heed the warnings. It is truly unbelievable to me that in 2020, any company can stay in business when they display such disregard for their customers. Be warned.

We purchased this oven/cooktop was installed in February 2020. I have been unhappy with the performance of the smaller oven from the beginning. It takes 20 minutes to pre-heat, a loud fan starts to run partway during the pre-heating process and then warm air starts to flow out the bottom. Plus, it is not either holding the correct temperature or not reaching it completely, nothing I cook in there is done in a appropriate amount of time. Baking a small potato takes an hour and a half at 375, brownies take almost twice the approximate baking time. My attempts to contact them have been less than satisfactory. I wrote for a second time over two weeks ago providing a copy of the invoice and have still heard nothing. I am quite disappointed with this product & company.

DONT recommend model #MOH130. We were so impressed with the options that this oven came with. Sadly, with all the bells and whistles also came a ton of repairs. After the 4th repair, our service rep said the relay board needed to be switched out. (Half of the service men who came to my house seemed to be grasping at straws trying to come up with an explanation why the temperature was fluctuating, or why it took so long to heat up, etc.) Then I get to wait 2 weeks for a part to be ordered/arrived and re-schedule service. Last week got code U22 - oven wont even turn on. This oven is only 6 years old. NO THANKS - NEVER AGAIN will I buy anything from this company.

The ovens needs a new latch kit and a mew control panel every year. It has been repaired 15 times. So many issues but those are the most consistent problem areas. Dacor should have replaced our range the first year. Even the repairman says everyone has had the same issues. For what I have paid in repairs I could have bought a new range.

I have an older cooktop. Yes it is 15 years going strong but I have ran into a few issues where I know the repairs would be pricey but especially the parts. After talking to a few representatives, they truly want to help you. Nothing is free and I don’t expect it to be, but I am glad they they helped me get my cooktop back to functioning again. I hope someone finds this helpful before reading or writing bad reviews.

When my husband and I built our home 11 years ago, I splurged and got a Dacor ERD36 36 dual fuel range. During the process of our build, our builder dropped my range during the installation. Dacor was very quick to send out a servicer to make sure the performance of the range was not compromised. The only thing that needed to be replaced was a bent bullnose in the front and the kickplate. I have had one service call in 11 years, which was last year after a brownout in my neighborhood caused my clock and oven setting to go crazy. It had nothing to do with function and had nothing to do with shoddy manufacturing. I just got it fixed and continue to use my range every day. I am looking to expand my island because I need another oven and I am very excited to add a Dacor oven to my home with zero hesitation. I am looking at a DO130S. I would buy Dacor over and over again!

Dacor 48 dual fuel range - Only 3 years ago, we purchased a Dacor range that is beautiful and worked great for 2 1/2 years. During the last six months, I had the led lights go out on some of my cooktop knobs and my oven has started not baking evenly, much as described in a previous post (half of your cookies can be burnt and the other half dough). A serviceman has been out twice and I have been made to feel that basically, I dont know how to use this oven or dont know how to cook. Funny that has only been in the last 6 months. I cooked great with the range for 2 1/2 years and have 20 years of cooking experience, but obviously, I dont know what Im talking about. To replace a led light bulb, I had to purchase a $300 control board part (that Dacor did discount) plus a $100 labor. It ended up being a $250 light bulb fix that has exploded to a potentially additional $600 problem. When taking off the range lid to replace the lights, I am now told that 3-4 burners have to be completely replaced and this again is my fault somehow because the metals fuse together and that is known by Dacor to happen, but my service tech said its because I dont clean my range well enough. This still makes no sense. And to fix the oven problem, it might be the control board? Lets throw my money at it and see? All guessing, the serviceman, Dacor, etc.! So now Im stuck with a parts bill of over $1,000 (Dacor did discount this to about $300) plus $200+ in labor, another guess. This just seems ridiculous to change a light bulb and guess at an oven fix for a 3-year old range that cost as much as a car! Im so irate over the whole issue! What a mistake Dacor was.

I wish I had read all these reviews of Dacor products before being duped into paying for a high end wall oven. As many others have mentioned, the electronic panel design is faulty. I paid $1000 to have it replaced once. Now it is broken again and the alarm beeps constantly. The reply from their service rep was that they havent had any recalls of this product (in other words, no ones house has burned down yet). He also admits that he wouldnt buy a Dacor oven unless he had money to burn. Well, my money has already burned and so have I.

My Dacor Preference 30 double wall oven (model PCD227R) was installed on 5-14-2004. On 12-31-2007, I replaced the upper oven high limit switch for cost $146.56. On 5-19-2010, I reset the lower oven high limit switch for cost $95.00. On 8-27-11, I replaced main control panel (Bezel Assembly), whose parts cost $271.10. On 12-14-2011, I replaced the main relay board for $214.02. On 1-16-2012, I replaced main relay board again, and it is under warranty. On 2-3-12, I replaced upper oven temperature sensor for $32.09. I am awaiting authorized Dacor service technician to calibrate both ovens.

I purchased a Dacor range hood 3 years ago. I had an intermittent problem from the start, as one of the two lights would intermittently go off. Replacing the bulbs didnt fix it. As one light worked perfectly, it became a tolerable issue. Finally, I was having other electrical work done in our home & I asked my electrician to look at it two weeks ago. He figured out that it was a defective lamp housing that incorrectly held the lamp bulb. Dacor shipped me a replacement lamp housing for me at no charge. I installed it this last weekend and it is running fine. Thanks, Dacor!

We bought the Dacor Wall Oven (ECS136SCH) in 2006 during a complete kitchen remodel. In 2009, the relay board was replaced twice. The first time, it was over $500 to replace. The second time, it was covered under the parts warranty when a terminal was bad. Now, I need another relay board and a new element which will cost over $700 to replace. For an oven that was originally over $3000, this is not acceptable, but what other choice do I have? The technician told me that Dacor has the worst mark up for replacement parts. I thought I had done my research and found that Dacor had a good product. I guess I was wrong.

ZERO STARS if I could but DISAPPOINTED - if I had to use one word to describe our experience with Dacor with not only our $8K+ 42 Built In Refrigerator that is sitting at 70+ degrees in the freezer and fridge sections but SO DISAPPOINTED with their poor customer service and lack of concern resolution tools for their team to even try to help.They are supposed to have high end luxury products. With that, anyone would expect to have a luxury customer experience. However, our family has been WITHOUT a working unit since January 6th. That is less than a month from when we had it installed but almost a month from today. We followed the proper protocols to get it repaired. Took almost two weeks to even get a technician. Once we did, he confirmed it needed to be replaced. We got approval and now learned we have wait another 2-3 weeks to get a separate decision to be made.Requested if there is any way to escalate our concerns but cant even talk to a supervisor for another 24-48 hours... Apparently they will call when it is convenient to them. Dacor - have some empathy for your customers! Imagine paying for a high end product to have no working fridge or freezer for a family of 6. Not sure how this is an acceptable practice. POOR QUALITY, UNTRUSTWORTHY, DOES NOT CARE ABOUT THEIR CUSTOMERS.

I purchased my first Dacor appliances in 1991, built a second house in 2005 and again purchased Dacor double ovens and a cooktop. Loved them! Remodeled my current home and again purchased the double ovens and a cooktop. The double oven, DTO230FS, which was installed in November 2015, 4 years ago, stopped working. I was roasting asparagus and we smelled what seemed to be burning plastic. The oven is used about 4 times a month, I have never used the self cleaning feature therefore it is surprising that it broke. The repairman said that the relay board was bad and will need to order the part. He estimates that it will be $600 to fix it. Sad that I need to incur the repair cost of an oven that is only 4 years old.

We moved in our new home in June 2019. We had purchased 2 Dacor dishwashers, 2 ovens, a gas cooktop and a microwave. All the appliances are beautiful. That said, both of our dishwashers leaked so bad we had to stop using them as they were damaging our wood cabinets and floor. Dacor sent service persons out after multiple calls and replaced the seals, but they still leaked. Our cabinet company that sold the Dacor appliances stepped up and replaced them both with Bosch dishwashers.Our Dacor Refrigerator went out in mid February and will not cool anymore. After 2 hours on the phone with a Dacor representative, we finally were able to schedule a service person to come out a week later (Dacor has very few support companies so dont plan on anything happening too soon when there is a problem). Was not able to repair the fridge and said it could be another two weeks to get the part and return. That said our service person is a great guy and cares, but has to rely and wait on Dacor for responses and parts.Our ovens take twice as long to cook as any other oven we have ever had. We are asking them to look into that as well. Overall, very disappointed. We understand having problems, but expect Dacor customer service would be much better and support their own field service persons and clients or at least act like they care. Not looking forward to calling them back to see why we need to be without a fridge for 3-4 weeks total....

We purchased our range (Dacor Dual Fuel Range RSD30) in about 1997 thinking we had a good investment. We have replaced the bezel 5 times (the area that encloses the control area). Today the door glass has cracked. Whooppee! Merry Christmas! Each time I called about the bezel, I was told that they had a design flaw. The last time we had to replace the bezel and also pay for installation ourselves. We decided if this happened again, we would get rid of it. Well, it will be sooner than later as the oven glass has cracked. Needless to say, we are not return customers.

We purchased this unit 7 years ago, just a family of two with visiting grandchildren. Unit came, had a crooked door and a bent latch, which we had serviced and supposedly corrected. When self cleaning the latch still made grinding noises. Over a year ago the oven stopped working period. A December service call said needs a new latch, sensor and display -we are now in 4 figures($). Oven operates for month and a half. January 2019 Service call now new door latch, relay board and main wire harness 4 figures again double! Oven stops working yesterday (June). Service call today new latch, motherboard and something else and another 4 figure repair cost. Same repair parts same problem! Patience is a virtue, but repair costs are sinful! Next step, Boat Anchor! Problem from the beginning and still a problem now.

We have a new (one year old) home with Dacor appliances. The microwave oven went on the blink the first month but was repaired by a factory approved repairman. Something to do with the computer. Now the double oven will not hold a temperature. We set the oven at 420 and it only goes to 360 even though the readout shows 420. We just decided to skip the repair process and bought a new Wolf oven. This is our second Dacor within the past two years and both have had the same problem. Dont waste your money.

I just had an appliance repair company come out to let me know what is wrong with my Dacor Stove door, since it wont close. He said the hinges are needing to be replaced. He said that he replaces these hinges on Dacor stoves ALL THE TIME and that the company really needs to file a recall on these hinges and/or reimburse consumers who have these installed. He said these should not go bad like they do. That this is poor manufacturing on Dacors part and they are not being held accountable. I agree 100%. It is going to cost me with labor and parts almost $ 400.00 to replace these hinges that should not go bad with the age of the stove. Thanks.

Worst oven Ive ever purchased by far. Pay big bucks and get junk. About 2 times per month, the oven will not heat up. I cant count the amount of wasted food and dinners out, because it does not seem to ignite, only warm up to about 100 degrees. I contact the appliance repair company and it works when they come out, so they dont do anything. I will never, ever buy another appliance from this brand.

We bought a whole new kitchen's worth of Dacor appliances - the Modernist line. It's too soon to review their performance, but so far they work well and look fabulous. Most importantly, I had an issue registering my appliances for warranty. I sent an email and not only did they resolve all my issues, registered everything for me, they also notified me I was eligible for an extended free warranty program, and they set it all up for me without any effort on my part. I wouldn't have even known if they hadn't done it for me. So far, I'd say that they have stellar customer service. When researching online before making the choice to go with Dacor, I had trouble finding information and reviews. I wanted to make sure and share my good experience since all too often people only share when they have had a negative one. I hope this is helpful to someone looking to buy!

The first F1 Error needed a new membrane repair for $470.00, after 4 years of service. Now, the same F1 error after the new membrane is only 13 and 1/2 months in service and it is now out of warranty. Customer service people are rude and unhelpful but when pressed, they said they might be willing to help after a service tech, which I have to pay for, diagnoses the problem.Even the Sears store people advise their customers not to buy Dacor products and that is sad because it is one of only 2 American made options. Dacor needs to step up their product engineering, commitment to quality and get rid of the rude phone people in Customer No Service. This is not the end of this experience but the only reason I am not junking the stove is because a comparable replacement is another 3000 bucks from another vendor which I cannot afford at this time.The irony of this is that the company clearly knows they have problems but when I asked if the replacement parts had been improved so the problems wont persist, I was told that no changes or modifications to the electronic brains had been made. How stupid is that! They are just asking for more problems with the parts they send you to fix what does not work.

Dacors wall oven wont heat up after I used Self Clean feature. Dacor said there is a reset button behind exhaust frame on oven (close to door latch). I called when I could not find red button and was told it was hard to find and they did not know exactly where it was located. Maybe I should call repairman. Any suggestions? Has anyone else had problems after cleaning oven? PS: My 5 year extended insurance expired Nov 11.

Bought expensive refrigerator in Miami. And because I live in Miami 2 months in year use and tern in refrigerator only for 2 months. Every year have problems for thousands dollars. Company keep changing parts. I keep paying. Same problem every year. Big mistake to buy Dacor appliances. Regret very much and angry. People who fixing they know nothing. Only money. Very not happy. Looks like new. Today will throw on the garbage.

Dacor ERD30S06CHLP 30 Inch Epicure Series Freestanding Dual-Fuel - I am so dissatisfied with this product. We bought the first range in 2003 and were so excited to use it. We chose Dacor over Wolf. From the beginning we had issues with the oven. It cooked very unevenly and the door never closed properly. We had a service call and they basically told us that we got a lemon. They offered us a new range for $3.5K. We thought we got a lemon so we agreed and paid for a new one for $3.5k. We also purchased the extended warranty for $2.2K.0 This one was even worse.One time I opened the oven and it burned my eyelashes. I wrote and complained with a video of the explosion and had to pay for the service call. I wrote a review in the website and they deleted it. We now own a range that we have paid over $10K that bakes unevenly, electric element does not work in oven and have minor explosions from time to time with a door that does not close. We have a few friends who have asked us about our range and we always recommend against it. We are looking for a new range. I would not recommend this range. I thought we got a lemon. But it seems thats just the product.

After 4 months our microwave exploded when we tried to bake 2 potatoes. Dacor has reviewed the situation and acknowledged the product was defective. 10 weeks later they keep saying the replacement is on the way but no one knows where it is. Dont buy dacor products.

I recently upgraded my kitchen and had always heard that Dacor has been a reliable high end brand for kitchen appliances. Their refrigerators have a lot of space, and everything can be easily organized. All the appliances work as intended, and they also all look great. The stainless steel Dacor uses to make these appliances look smooth and clean, making it one of the most beautiful kitchen appliances I have ever owned. If you want a functioning kitchen with appliances that always look nice and shiny, then I would highly recommend Dacor.

We used a new Dacor range vent only to have it go on and off. We called Dacor and they referred us to Desert Tech in La Quinta. The owner came out and said we needed a new unit for $775. We said just unplug it. He charged us $275 even though it took him less than 30 minutes. Stay away from Dacor AND Desert Tech!

I purchased a 30 Dacor dual fuel range and matching hood in 2004. I paid $4009 for the range and $948 for the hood. The range and hood have been nothing but problems. I wrote to Dacor in April 2009 detailing the problems with the range with service history dating back to 2006. Problems include overheating when cleaning which is a safety risk, replacement of cooling fan, ignitor assay, part # 92309 membrane, and replacement of relay board in 2007, 2009 and again December of 2011. I attempted to purchase a Dacor extended service agreement in January 2009 but was declined due to the ranges past history and its age. I recently found this site which indicates that other consumers have had similar problems with Dacor products. Dacor has lost me as a customer as I will never buy another Dacor product! I have been disappointed and frustrated with their lack of response and support. I finally purchased a GE service contract which has helped absorb some of the cost of ongoing repairs. The overhead lighting has long since gone out in the hood. I was told the hood needs to be disassembled to replace the lights. Dacor should step up and support its products. When most people put out $4000 for a range, they expect to get a quality product that will last 15-20 years. With Dacor, this has definitely not been the case!