Weve had these appliances for 15 years. The cooktop has worked well. However, it could be improved with a lower lever for heating on its small burners, allowing it to simmer water rather than boil. The Dacor exhaust we purchased is one of those type that pop up out of the counter. It works but leaves much to be desired. When it runs, it pulls so much air the flame goes out on the burners. It is still not efficient at getting rid of cooking smells or smoke either, but that is simply a problem with all of this design so I cant fault Dacor. We have the biggest problem with the double oven. There are three main issues: 1) Whenever we run the self cleaning function, it pops the heat safety switch inside the oven housing so I need to take it apart to fix it. Hence we work to keep it clean so we never use the cleaning cycle. 2) The oven door gaskets prevent to door from closing and sealing all the way. The door tilts out app. ¾ because of this. We were told by the service guy who came to fix problem 1 above that this is the way the doors are(!). Our bottom one also tilts out but not as much. Ive dealt with this for 14 years! 3) We have to sand the burner electrodes on the cooktop to ensure they spark to light the burners at least 2-4 times per year. Not sure if that is normal or not.

I purchased my 30 range and was so excited! Well no longer. First the wrong range was delivered. I had to wait another three weeks for the correct one. My oven can not cook at all. Temp fluctuates by 100 degrees. Going on my third service call and still not working. It very unfair, I have to take time off work to wait for repair person, then nothing is fixed. I wish I could return this lemon. But after reading other reviews I am not alone. Why is this company not accountable for ripping hard working people off. I love cooking. Its my passion. My Kenmore Elite was half the price and far more superior.

We purchased this range after remodeling our kitchen. We opted for the Dacor because of the deep oven that the other high end ovens did not have. I am an avid baker so this was a plus. After a year and half the oven stopped working, it was not getting hot. Thankfully is was still under warranty and it was repaired. The technician determined it was the oven control thermostat that was not working. Fast forward two years and again the same problem, along with the right front burner now also not working. And wouldnt you know it, the warranty is expired. Another technician came out again and stated to fixed the two problems it would be approx $250.00 just for labor and not including parts. CRAZY INSANE!!! If we would have known all the problems and we would have purchased either a Wolf, a Thermador or even a Monogram. How can so many issues and problems be happening with an range that is only 4 years old? Especially one that costs over $6000. It has to be a lemon or poorly manufactured. Ive contacted Dacor and was told they need to review my file to make a determination on what they want to do. REALLY, you dont need to be a rocket scientist to know there is a problem. Theres lemon laws for cars, why not appliances????

I purchased a Dacor range/oven combination in 2005 for a total kitchen remodel. I chose Dacor for its name and reputation for quality. The first problem was that the digital clock was running very fast; that occurred in October 2005 and was covered by the warranty. The next problem was that the downdraft would not stop going up and down. I had to turn off the breaker switch of that function until the repairman could fix it. The next problem I consider as a design flaw and not an oven malfunction. Both oven lights were burned out by June 2010 and needed replacing. The light bulb cover for my model is behind a grid for the oven racks which must be removed before the light can be accessed. It’s not a 5-minute job. The next problem was in September 2010 when the oven broiler refused to work. Another service call was needed to replace the oven broiler ignitor. The next problem was in June 2011, when the oven rack, which slides into cavities built into the rear wall of the oven, refused to release. It required another repair call. The repairman had to pull the oven out away from the wall and work to release the rack. As a result, I do not use that rack. Theres no one who uses the oven besides me; I have no kids in the house. The oven has never been misused or abused. The next problem was in November 2012, when the self cleaning feature refused to work; another repair call was needed. All of the above cost me $1,250. When I contacted Dacor about the myriad of problems/issues, I got a written reply that said every situation is reviewed on a case by case basis; in most out of warranty cases, Dacor would sell me the part I needed at a reduced price. I responded that would necessitate two service calls (one to diagnose, one to fix) and an inoperable oven for however long it would take to get the part and then reschedule the repairman. In almost all of the above, my repairman (Dacor authorized repairman) had the parts on his truck. I cant be waiting weeks without a functioning oven. Based on all of the above, my oven would have been out of order for many weeks. I wrote Dacor again, thinking the CEO needs to know about all these problems. I asked my contact to forward my correspondence to the CEO for review/comment. Instead, I got a reply from the customer service supervisor who stated in part on his 1/3/13 email, There tends to be a disproportionate amount of negative postings on-line”. Really? Most companies pay attention to complaints or compliments about their product or service. If someone takes the time to communicate, then the company owes its shareholders the duty to listen when there are repeated complaints about their product. Will I buy Dacor again? Never.

I own a complete Dacor Kitchen, with many appliances. They are the highlights of my Home. Great features: fast induction cooktop with an efficient silent hood, versatile refrigerator, reliable oven, and of course the always dependable dishwasher. This is My Dacor Kitchen!

We did a complete kitchen remodel 2 years ago. My husband talked me into purchasing american made over the Bosch products that I preferred. This has been a horrible experience. The dishwasher does not clean. I was told to prime the water and purchase the higher end platinum packs. That did not work, then it was add lemi shine. That has not worked. The water never completely drains, ugh old water. A service tech could not tell me where the rinse aid indicator light was and insisted mine did not come with one! Microwave does not heat in an adequate time. All listed times I have to double time if not more. I was told to put a Rubbermaid container over the food product to insulate the waves... ha! Oven does not regulate heat. when I go to increase the heat during stated recipe, the screen always say 50 even though I would have it at 375. I was told it always will revert back to 350, really. I had all Kenmore appliances prior to the Dacor and never had a problem... Do not buy, I wish I hadnt. We are filing this with BBB and headed to small claims court.. This should be fun. I hope Dacor sees this.

We installed 2 Dacor wall ovens, a 5-burner cooktop, and a downdraft fan in 2000. The convection ovens bake perfectly and have performed without fail. After 7 to 8 years of daily use, we did have to replace the door hinge on the oven I use most often. We are in a rural area so the repairs are accomplished through Sears. The replacement parts arrived in a timely manner and the oven has worked perfectly since. The cooktop is easy to clean and the heat is even. The downdraft fan is effective and easy to clean. I would be confident to recommend Dacor products.

Updated on 11/29/2018: Further to my recent review of my Dacor wall oven, I went to a high-end appliance store yesterday to research replacements for my microwave, oven, warming drawer installation (so, yay, I get to spend $13,000-plus to replace items I have had for only eight years). I cannot verify the accuracy of this, but the salesman explained the problem. For a period of time, Dacor and Viking used the same third-party supplier for their relay boards. Unbeknownst to the companies, the supplier substituted a part that was later discovered to be defective. Unfortunately, all replacement relay boards contain this part, so the problem will recur repeatedly, as many on this site have discovered.As bad as the cost of periodically replacing the board is, the unreliability of the oven is worse. As happened last time, mine works OK sometimes, burns everything other times, and struggles to get to the desired temperature other times. And because the behaviour is unpredictable, it cannot be reliably recreated when a repairman visits. I have had one email from Dacor and I responded with the information requested, then nothing. I suspect that they know they cannot fix the issue in a permanent way, so theyre just hoping all of us with this defective part will just go away. It looks like newer models that look like mine are still available, but I refuse to pay $5,000 on the off-chance that it has a better relay board. I am looking at Miele replacements.Original Review: I have had two Dacor wall oven, microwave, warming drawer installations. The first one was only a couple of years old when we moved, and Id had to replace the microwave, but I put it down to a power surge in the house after an outage. I have now had the same set in my new house since 2010. I have had to replace the microwave again, but not because of a power surge. It just stopped working. The oven has been a complete nightmare. The probe broke and although I had it repaired, it never worked properly, but the worse problem is that I am about to have to replace the electronic board for the SECOND TIME. When the problem occurs, the oven heats up to the setting but the element just stays on. I all but ruined an expensive cut of meat on the weekend – with company coming, no less – and just had to throw out a batch of muffins. I am considering tearing out the whole installation and getting another brand that doesnt destroy my food. It would probably be cheaper than having to fix the oven every year or two and replace the microwave periodically. These appliances are garbage.

We remodeled our kitchen in 2001 and bought a Dacor Epicure 30 dual fuel range. The gas cooktop has never been a problem, unlike the oven which has been a problem from the first week with unpredictable temperature variations. Multiple holiday meals have seen the extended family waiting for dinner for two hours because the oven decided to be cool that day. The advice from Dacor: preheat your oven for several hours before you need it or my favorite from a repairman: you must be slamming your oven door. Not helpful. Several expensive repairs later (over $2100) and one fire in the oven now it wont turn on at all. We are going to try one last time to repair it and then we are done. I do not recommend Dacor to anyone - too expensive to have such terrible quality and service.

I have a 4 year old Dacor Renaissance 36 in gas range. The thermostat is broken, the self-clean cycle doesnt work due to a broken lock and the oven indicator light stopped working about 2 years ago. Pros: It is an attractive oven with the knobs that light up blue when on and the burners all work fine but that is it! The technician told me ALL parts I need are on backorder due to Dacor being bought out by Samsung 2 years ago and COVID related delays. He also told me there is no ETA on those parts and said it could be an unknown amount of months. So now I dont have an oven for an unknown amount of time. This is unacceptable. I was sharing my frustrations with a friend who recommended I post this on Dacor Applicances Facebook page. He thought I would get an immediate helpful response. So I did. It was taken down not more than 3 minutes after it was posted! They never even reached out. Pretty poor company service. I will never buy Dacor anything again. Even when the oven was working ok - it never kept good heat and the self-clean cycle never cleaned well - there was lots of grease residue left behind. This is a poor quality company all around. Believe the negative reviews. If I could give negative stars, I would.

We remodeled our kitchen in 2016. We chose Dacor 30” range. The gas oven has been a disaster. After less than a year, it wouldn’t heat. They replaced it, same problem. Replaced the igniter and valve, same problem. Now they will do nothing and say we’re on our own. Problems with hood and fridge too. Stay away from Dacor at all costs!

We purchased Dacor appliances twice, (double ovens, warming drawer and gas cooktop), after our first flood, and then again, after we flooded from Hurricane Harvey. (Dacors customer service was excellent in helping us replace all our appliances when we were going through such a horrific disaster because the vendor we purchased our appliance from the first time, wasnt in business anymore.) We were very satisfied with our appliances the first time we remodeled, that we purchased them again, and have not had any problems. The ovens heat up quicker than other high-end ovens and the range top cooks evenly and looks beautiful. I would purchase again, but hopefully, I wont have to.

The Dacor dishwasher had problems engaging and activating the cycle. We finally had enough and purchased a Bosch dishwasher even though the rest of our kitchen is Dacor. The new Dacor was $1600+ and the reviews on all their dishwashers since 2007 are one out of five stars. Dacor knows there is a problem and wont rectify it with the consumer. An amiable young man called from Dacor. He stated he would help me on any future problem with the other appliances. Why irritate the ** out of Dacor consumers when your company has had a history of irate consumers, specifically regarding the dishwasher. This certainly doesnt increase sales and only angers the base.

We bought the Dacor Wall Oven (ECS136SCH) in 2006 during a complete kitchen remodel. In 2009, the relay board was replaced twice. The first time, it was over $500 to replace. The second time, it was covered under the parts warranty when a terminal was bad. Now, I need another relay board and a new element which will cost over $700 to replace. For an oven that was originally over $3000, this is not acceptable, but what other choice do I have? The technician told me that Dacor has the worst mark up for replacement parts. I thought I had done my research and found that Dacor had a good product. I guess I was wrong.

Ive had the pleasure of owning a PGR30S range from Dacor for the past 20 years now, I must say it has past all my expectations on performing in the kitchen. This unit cooks everything amazingly well... Thank you Dacor for such a great range.

I owned a 36 Dual Fuel Epicure range that required at least an annual repair for the same thing. The control pad (the pad with the buttons that controls the oven and light) would fry. This would cause the oven light to come on and off like a strobe light. Luckily, I purchased an extended warranty from the vendor, as each time this was replaced it was $750+ to repair. When I complained to Dacor on their support line, the representative actually told me that I was running the oven too hot!About 6 months ago, I sold the house and left the very expensive range behind. It was problematic from day one. Other repairs included replacing the ignitors. After a year of use, the insulation on the door came loose and was hanging in plain view through the window on the door. Every repairman that came to service the range said the same thing.... that they repair a lot of Dacors. When it worked, it was a great range. If you do buy a Dacor, do yourself a favor, buy the extended warranty. You will need it and it will pay for itself.

I have the Dacor 30 all gas range in my house and it is the best. The grates take up the whole top surface of the stove area, so I have a ton of room to cook on. Basically, I can fit 4 giant pots on the stove at the same time, so Im ready anytime a chili cookout might break out. This is also super convenient during tamale season and soup season because I can put up to 4 giant stockpots on the stove simultaneously. In the event that I spill, its easy to remove the grates and give the surface a nice wipe up. As far as the oven, I totally rule the holiday season because I can fit up to 3 full size 18x36 catering sheets in at the same time, so basically, I can cook 4 dozen or more cookies in one shot, leaving me tons more time with family and friends than if I was baking 1 sheet at a time. Thank you Dacor!

We bought our Dacor 30” gas range in September of last year. We were tired of cheap stoves that lasted 5 years before they needed to be relegated to a landfill. We thought it was an investment that would provide us with a reliable appliance and worst case scenario, better warranty repair service than Home Depot or other big box store.After 15 months, the igniter for the oven stopped working. We tried the 800 number on the warranty registration website and no one there could bring up our registration, even though I could see it on the website. They gave me an email address to contact the people who could look it up and I heard nothing for two days. I called the 800 number again and they transferred me to another number and they finally found our warranty registration and issued a ticket for the repair.The company they use for warranty work in Toronto, is Home Appliance Repair GTA and they are absolutely horrible. They said they ordered the part on November 27, but they did not actually order it until December 6th. Dacor then sent the wrong part! I demanded that they send the proper part overnight and on December 13th they called and left a voicemail saying that the part would be here by today at the latest.It did not arrive and this evening I emailed them again and their response was that the part would be here on December 19th. How does it take a week in this day and age to deliver anything? I don’t believe that I will even have a functional oven for Christmas this year. I have already given up on any baking getting done. I will never buy a Dacor product again. I actually really love my stove, but I am beyond disappointed with their warranty service and customer care.

I called the customer service number regarding my double oven. It just randomly beeps and now turns off. No error code displayed. It has done this on and off since 2003. Now it is happening all the time. I called customer service and they seemed to act like it is my fault and I need a new touch pad. I inquired and this is a recurring problem with this model. I could not get a straight answer from the person I was talking to. He just told me that if the repairman says I need a new touch pad, then I need to get one. Well I have been doing some research and this is a problem that seems to be haunting more people than I. We own a Dacor gas cooktop that has had to have a switch repaired. We own a microwave that has had two new circuit boards and now a beeping oven that gives no error code and turns off by itself. My advice, do not buy Dacor appliances.

First six month, dishwasher rusted on the inside. Dacor gave us a less expensive in its place. First year, microwave was repaired five times. Microwave has a piece of wood to hold the door in place. Wall Oven, the broiler never work. Present, range oven does not work at all. We have a repairman that is trying to get parts. Present, refrigeration control panel does not work, need repair. These appliances were to be a our luxury kitchen, but turn into a nightmare. Do not buy this appliance, you are wasting your money.

When my husband and I built our home 11 years ago, I splurged and got a Dacor ERD36 36 dual fuel range. During the process of our build, our builder dropped my range during the installation. Dacor was very quick to send out a servicer to make sure the performance of the range was not compromised. The only thing that needed to be replaced was a bent bullnose in the front and the kickplate. I have had one service call in 11 years, which was last year after a brownout in my neighborhood caused my clock and oven setting to go crazy. It had nothing to do with function and had nothing to do with shoddy manufacturing. I just got it fixed and continue to use my range every day. I am looking to expand my island because I need another oven and I am very excited to add a Dacor oven to my home with zero hesitation. I am looking at a DO130S. I would buy Dacor over and over again!

We purchased this high end Dacor range (Dacor Renaissance ER30G) new in 2011 from the Appliance Loft here in Cincinnati. It was dropped off and installed and would not operate right out of the box. A repair was made and everything worked (unless you count the indicator lights on the knobs, they all went out after approx 14 months). This past November the oven went dead. A1 appliance came out: Determined new control board needed, ordered and installed. Thanksgiving Day, oven dead. A1 comes back, reset the High Temp Fuse. Oven dead 4 days later, A1 returns with a new HTF. Dec 22, Oven dead. As soon as The holiday is over we will call another repair shop and start looking at replacing this unreliable piece of eye candy. Open comment to Dacors design engineers, quality control engineers and management. You should be totally ashamed about this product youve designed. You are supposed to represent the best in American design and quality and this falls below that of low end appliances out of China. See you in small claims court.

Dispenser spits out ice cubes onto wood floor everyday. Told it is design issue and nothing can be done. We have to constantly check the chute is empty after used but we can be nowhere near the fridge for hours and hear ice pop out onto floor. My grandson has tripped and fell and me also. Im more concerned for safety than anything. Also our hickory wood floor is concern.

Dacor Distinctive Series Range model DR30D - One week after the appliance warranty expired, the oven stopped heating. The repair man replaced the circuit board. We still got a code 33 when we try to get the oven to heat to 400 degrees. Called customer service, they said to flip the breaker to the unit off for a few minutes. Seemed to help but we do not use the oven much, as we also have a Meile microwave/oven that we love and use that more. Then I cleaned the oven using only the ovens program. That locked down all of the gas cook top knobs. I called the repair service, it snowed on the Saturday of the appointment. They cancelled. I did not check the stove on Sunday. On Monday the repair service walks in and simply turns it on, no problem. VERY FISHY!!! I have heard the manufacture can control it by computer chips. This appears to be very true. Now the stove does not heat past 250 degrees. After speaking to a few people it appears this is a very common issues. Dacor is a lemon. Do not waste your time and money.

Purchased Dacor Induction Range w Convection Oven RR30NIS-C in October 2013 and LOVE this range. Accidentally broke the glass on the induction cooktop with falling object mid-March 2020. Only the glass is broken, and all other electronics, induction burners, oven, etc are functioning fine. Called Dacor support to acquire part number for a glass top for repair - obtained part number #701751 superseded by #702285, BUT was informed that the part had been discontinued and is no longer being manufactured or kept in stock. No other advice was given other than to discard the entire $6000 range. Multiple phone calls with service.I asked for a listing of third party part distributors and was referred to four distributors on the Dacor public website and given no other info. I called all web-based third-party distributors I could find in USA and Canada to see if anyone had the part in stock, with no luck. I contacted two technicians to see if they would be able to obtain the part through their channels, with no luck. I am an engineer, so I spent some time pouring over technical manuals trying to find a solution to replace the entire induction range cooktop assembly (top part of the range) with a later model, and although its possible, Dacor would not provide the ability to purchase an RNR30NI range cooktop assembly that could be fit into the existing housing on top of the range. The convection oven is completely fine, and I cannot believe that Dacor has given me no other option but to pitch a six-year-old $6000 range because they stopped manufacturing one fragile part made of glass. I would imagine that many consumers may be in the same position as I, as these cooktops are breakable, and accidents happen. I have reached out to Dacor support desk numerous times without resolution, and I am at my wits end with a $6000 boat anchor in my kitchen. What a waste of money! Poorly done Dacor!I would like Dacor to provide me with some sort of solution whether it be the part required to fix my induction cooktop, or a replacement Induction Range with convection oven, or reimbursement of the purchase price so I can obtain a replacement on my own. If I am not able to find a solution to repair my range, I will never buy from Dacor again! Dacor will discontinue easily broken parts without warning! You may spend thousands of dollars and not be able to repair your appliance after warranty expires!

I purchased my Dacor range in 07. After running the self clean cycle today, my oven wont heat up using convection or regular bake. Keep in mind, I had the entire electronic guts of the oven replaced in March 2011, 6 months ago after the same full failure. I paid $6,500 for this appliance. I wish I had my old GE oven back. This piece of equipment is only 4 years old. My husband and I dont use the oven often. What a huge disappointment! I will likely spend the next few days on the phone with customer service.

I am having issues with my Dacor oven and have tried to contact customer service since Monday 01/04/16. I was on hold for 27 mins and finally left my number for a callback. I have called every day and leave my number for a callback, no response. Today Thursday I sent a message and the response was that someone will call within 2 days. Great customer service. Buyer beware.

Arrived in good condition and so far works perfectly. Delivery was delayed by one day because of the incompetence of my local mail service. I bought this microwave, as others have described, to replace a 13 year old Dacor that had not really died but had lost the electronic screen. We put magic marker numbers on the display screen where the numbers had been 5 years ago and kept using all the functions. I decided to replace as, without the display screen, I could not do anything semi sophisticated with this microwave but its motor and microwave capacity was still going strong. This model fits perfectly into the previous 24/27 trim kit. Unfortunately our other trim kit is white to match our old microwave. Decor only has stainless steel now. And the new trim kit for this microwave is flat without the vent slats (plus costs over $300!). From the placement in our cabinet, I think the vented slats are really important to dissipate heat and am puzzled by the change in design by Dacor. The slats are a little tedious to clean but as a TV is above the microwave and an oven below I want the heat to have a better place to go. Ebay has the old trim kit in stainless steel but so far the expense seems excessive for just the outside piece. The internal support bracket for the new microwave is exactly the same as for the previous model so the only part of the trim kit needed for my microwave is the outside frame. This newer model works very similarly to the older version. I am delighted Dacor still makes this microwave to fit my space 13 to 15 years later.

Unfortunately, the screw broke in two that held our Dacor refrigerator door on and much to our dismay, the door fell off. Dacor was prompt and courteous in sending a replacement lower refrigerator door hinge to the service company and covered the full cost of labor even though they initially said the refrigerator was out of warranty (two years old). Our experience was positive with James who gave timely and a customer-focused response. He also called to follow-up after the repair to make sure we were happy which I appreciated. I hated that the door broke but was very pleased with the repair and the fact that I did not have to pay.

We got a U43 relay error on our Dacor oven of 4 years. When we finally add up the cost to replace the part, it will exceed $500 and Dacors only response is, Sorry, it is out of warranty. Of course I do not understand why a relay board on an oven would short out after a few years. Not happy and would not recommend the manufacturer.

Previously, I submitted a complaint here and I would now like to amend it. The problem(s) that I experienced with my 8 years old Dacor 30-inch wall oven was what I described in my earlier post (July 9, 2012). But after posting here, I was contacted by a Dacor representative not once, but several follow-ups to ensure that the problem was resolved to my satisfaction. It was and Im now very impressed with Dacors customer support. To be fair, I should have contacted Dacor with my problem before blasting their product here.It has been a good oven for 8 years and given their support that Ive recently experienced, Id be more inclined to purchase Dacor products in the future as it appears theyre willing to stand behind what they sell. Im really glad this issue was resolved because I was about to throw in the towel and buy something else, but couldnt find anything else that looked near as good as my Dacor and had glowing product performance reviews.

We purchased a Dacor gas range in 2005 for $2000. In a short time the plastic trim around the knobs cracked, and the glass in the oven door had not maintained its seal. I contacted Dacor several times and was told to take a picture and send it to them, then they could decide a course of action. The course of action was that I would pay for materials and labor. I decided not to do that, and eventually I will replace the range with another brand, never a Dacor!

We were out of state from December 21, 2014 to January 2, 2015. The condition of the refrigerator was discovered at about 9:30 PM on Saturday, January 2nd. Upon opening the door the Dairy Compartment Cover fell to the floor. We could immediately see the damage but did not know the source. As a result, the unit was turned off. The owners manual was consulted along with a review of the Dacor website. The office was closed on the weekend so Monday was the earliest we could obtain names of Dacor authorized repair agents in the Phoenix area. A authorized Dacor repair technician stated the light switch or light circuit in the board failed. The interior light bulbs located at the top of the refrigeration side of the unit remained on when the refrigerator door was closed. The heat generated by the continuously lit bulbs led to the melting and charring of the plastic light fixture. The light socket melted, the wiring harness melted into the socket assembly, light switch, and control panel. The heat was intense enough to warp the Dairy Compartment clear plastic cover, some of the adjustable door bins, and the interior door liners. Also, all food containers made from plastic such as salad dressing bottles, mustard, ketchup and mayonnaise, etc. were disfigured. Of course all the contents from both the refrigerator and freezer had to be disposed.Before leaving on an extended trip we had been following the instructions preparing for a vacation listed on page 19 of the owners manual. On our departure date the food that would not have lasted more than two weeks was removed from the refrigerator. The ice bin was emptied and the wire shut off arm was raised to the OFF (O) position. Note, page 19 does not mention to set the Sabbath mode when leaving for a short or long vacation. We were fortunate that the damage was contained within the refrigerator.

We purchased a Dacor wall oven when we renovated our kitchen in 2010. After five service calls, a replaced circuit board and broiler element, they found a broken wire which must have happened during clean cycle. I have been without an oven for two months and would not recommend buying a Dacor oven because I think it has a faulty design. The issue is still ongoing.

Talked into spending $4700 on a wall oven on the recommendation of an appliance retailer. My concern was even baking and reliability. Was told I would be very happy as Dacor was best on the market. Well long story short, it never cooked evenly and after 8 years quit working. Had to lug the heavy oven to the city to an approved service provider. They thought it was the relay board (told the brains of the oven). Service provider changed several things (sensors, board and whatever else). Nothing solved problem. Phoned me and said I was looking at minimum $2000 and up. He threw oven in garbage. We didn’t even send the gas money to bring the dud home.Thought it should last longer than 8 years. I phoned Dacor. They wanted to know exactly what the problem and diagnosis was so I told them to phone the Service Provider. Said they would but I had to email copy of receipt which I did. A couple of months gone by and never heard a thing and they are not responding to my emails. DO NOT RECOMMEND DACOR.

We purchased a DACOR double wall oven (MOH2275) in April 2012. We are waiting for service to arrive for the fourth time since we purchased the oven. I find this unacceptable. We have had 2 other ovens in the last 30 years and they did not need any service. In general I have found appliances to be of such reliability that I dont get extended warranties. DACOR gave a 3 year warranty on this oven and now I know why. Hopefully this service will fix it for a long period of time.On the positive side, the oven really works well. It is so well insulated that we feel very little heat coming off it. One serious flaw its overall operation is the reheating of the oven. If I bake something at 350 degrees and then want to reset the over to 450 degrees, the oven does not go into preheat mode and does not let you know when you reach the required temperature. I am hopeful this will last awhile and not have to be replaced for what we paid for it.

Perfect size burners and small oven. Cooks food perfectly about 25° less than you think. Great grill on top. Easy to clean.

I moved into a house that already had a Dacor unit in place. Within months, I discovered that I owned an oven that could be fixed by throwing the circuit breaker. Then, I learned about invisible hands that turned the 325 degree convection oven to a 500 degree broiler. The final act was having all three glass panes shatter and the control panel cracking as punishment for assuming that the oven cleaner on an expensive gourmet stove would function according to manufacturing standards. The repairman ordered replacement parts. He spoke with someone who was off shore so forget about Dacor being all American made. The wrong parts were sent. He has reordered. Meanwhile, I have been without an oven for two months. If this goes on, I am going to Home Depot and buying a Hotpoint or GE. It is the same price as replacement glass panels and the control panel.

We have a Dacor Epicure 36 six burner range. It has been a regular source of trouble since it was installed as part of a kitchen remodel in 2006. The igniter for the broiler went out 18-24 months after we got the oven. A year or so after that the weld that holds the bottom oven rack bracket to the oven itself popped loose making it impossible to use the lowest rack position in the oven. Last year the circuit board that controls, among other things, turning the bottom oven element on stopped working. Not only is the board itself quite expensive, but it is buried deep under the top of the stove taking lots of expensive hours of repair time to remove and replace. And now the burner igniters have begun to over spark (e.g., continue to click long after the burner has been lit, burners sparking that have not been turned on). The repairman tells me that is a different circuit board so we could be heading to another $500 or so in repair bills or perhaps a trip to the dump and a much cheaper replacement range. We have had other Dacor equipment (cooktop, wall oven, warming drawer) and have not had a problem with any of them. But given our experience with the Epicure I cant imagine ever buying another.

We moved into our home in July 2012 and have had nothing but problems from our Dacor refrigerator which was manufactured and installed in this home in 2007. The appliance repair company has been to our home approximately five times in the five weeks since we moved in. Initially, the problem was with a leak in the cooling system which took the technicians about 16 hours over three visits and $1,400 to sort out. Currently, we have been without a visit from the techs in two weeks (our longest stretch since moving in) and the refrigerator is leaking from the ice dispenser and making a motorized noise so loud. Initially, I thought a motorcycle had pulled into my kitchen. Needless to say, the technicians are on their way back.

I purchased a single wall oven in 2008 and 30 days out of warranty, the oven broke. Service required two service calls to fix the door magnets. A third visit was required as the oven codes shut down the unit. The last two service calls have been with the cooling fan. Now that the fan was replaced, the relay board needs replacement, too. I have spent $650 in service alone, which is separate from the cost of parts. There’s no help from customer service; in fact, the rep was downright rude. I will never purchase this brand again and I have told anyone who will listen not to purchase.

We equipped a luxury kitchen with Dacor appliances. Had to replace the 60 inch dual fuel range after 8 years - use the same brand simply to match. Big mistake. Several repairs already. Also installed two under the counter warming drawers - nothing but problems and repair expense. Now we need a small $25 part - a cooling fan with motor that is faulty. Was informed the part is no longer available - customer service told me well, it is 10 years old. Really? We now have to rebuild part of the kitchen cabinetry and spend several thousand to replace two warming drawers? They also said the company was too small to keep parts available for a long period of time. Unbelievable! I will never buy Dacor appliances again.

We have a Dacor gas range RSD30R that we bought to upgrade our kitchen in 2002. We have had several issues with the range to date. The first issue we had with the range was the auto lock for the oven cleaning cycle that failed in 2007. It was not covered under warranty and cost $88. The second item to fail were the oven door springs. They also failed in 2007 and covered under warranty. They failed again in 2017 and had to be replaced for a second time. The springs are too weak to hold the weight of the heavy door. $68-$78 for the springs. The springs could easily be changed out as the brackets are still good but they only come as complete units. The last item to fail were the ignitors. Only one ignitor failed out of the four but as the spark module ignites all burners every time any one is turned on, premature failure could be expected as all ignitors light every time. This time the part is no longer available from Dacor. Dacor does not support any products they build after 7-8 years. Parts will no longer be available. I would not recommend Dacor Appliances to anyone as the manufacturer does not support their own products very long. I purchased Dacor to buy American and I regret it now. In contrast every product that Miele made even 20+ years ago, parts are still available directly from Miele and other suppliers as well.

Like many of you on this site, when we remodeled our kitchen in 2000, I researched and decided to shell out the extra money for the highly recommended and higher priced Dacor everything. We got a double oven, glass 30 cooktop and an exhaust fan. 12+ years later, I wish I had bought GE! My ovens have had so many problems I cant even count. Basically, the temperature doesnt hold correctly. I have used oven thermometers and my husbands fancy gauge to check temp. I had a whole transformer and control panel changed out in hopes that it would correct the problem, but it didnt. I think it has something to do with the self-cleaning. I think it gets so hot that it fries the controller. I never use the broiler so its not like I left the door open and wasnt supposed to. This afternoon I set the oven to preheat to 350. I set my little cakes inside that I was making with my grandson. About 5 minutes later, it smelled like something was burning so I checked the little cakes. They were already charring on top and then I noticed that the top element was fiery red, basically on broil! What the heck?! This is ridiculous! Im not going to spend another $500 for another repair! I am waiting to see what the repairman says.On another note, my stovetop cracked twice! The last time, Dacor was nice enough to sell one to me at cost and my husband was able to install it. It didnt match the old one and I was told by Dacor that they dont make them anymore and that is made by a third party supplier now. The old one had a textured finish and this one is just very shiny and scratches so easily! I hate it. We also had a retractable exhaust fan put in because the stovetop is in an island. Every time I turn it on, my basement smells like whatever is cooking. Now the buttons dont work anymore. That is unless I jab them so hard with a sharp object that it finally makes enough contact to work! This is another part that we got at cost that my husband had to crawl around and repair that still doesnt work.So, all three Dacor appliances we bought have turned out to be very disappointing purchases. Dacor should stand behind their products better, offer longer warranties or better yet, build better products! I would never recommend these products to anyone!

Two years ago, we redid our total kitchen at considerable expense. All of the appliances we replaced were made by Dacor. They included: 1) a 36-inch refrigerator model EF 36/wf; 2) a dual wall oven, model EO230SCH; 3) a gas cook top, Model RGC304; 4) a dishwasher, ModelEDWH24S and; 5) a range hood, ModelEH3012SCH. The problems started within a two months of installation. The refrigerator stopped running due to a relay failure and a compressor problem; both were replaced by Dacor at no cost to us. It was inconvenient but not costly. A short time later, the lower wall oven stopped working as well as the lights in both ovens. This required the replacement of the main control panel (control circuit board). Dacor paid to have it repaired. The clock does not keep accurate time and gains about an hour a day. We decided to leave it well enough alone and did not have it fixed. After the one-year warranty expired, the lower oven quit again. This time, it had to be removed from the wall and an exhaust fan in the lower oven was defective and had to be replaced. Dacor’s initial response was it was out of warranty, so it was up to me to cover repairs. They eventually agreed to supply the part (about $90) but we had to spend several hundred dollars to install. Now, the lower oven takes an extremely long time to heat up, and again we decided to leave it well enough alone. Recently, there was a loud flash in the vent hood; one of the bulbs apparently burned out. My wife tried to turn off the lights in the hood but the light switch apparently blew when the light went and could not turn them off. After a couple of burned fingers and a melted bulb removal tool, I managed to get the other bulb out. A call to Dacor got the usual out of warranty response. I called the local Dacor authorized service rep. He looked at the problem ($95) and said he would have to call Dacor. After he talked to Dacor, they called me and said they would send a replacement control board but would not pay for the service calls. The service company said the next service call would be $195. One light bulb burned out: cost $290. I suspect that every hood unit that Dacor made with this control board is also defective. We have had to replace the halogen bulbs with great regularity. We have halogen bulbs in our boat that have lasted at least 15 years. There was another complaint on this board that had a similar problem with the vent hood. He decided to fix it himself. He is an Electrical Engineer his comments are worth reading and speak to the inadequate design of this unit. It is a shame that the Dacor appliances appear to be near the bottom in terms of reliability. Consumer Reports that their gas cook tops appear to be the least reliable. It looks like I have something to look forward to. Needless to say, I cannot recommend Dacor to anyone. In fact, I would recommend that they not purchase any Dacor product that does not have a full multi-year warranty.

We purchased a under counter Dacor oven. The timer started given problems, tried contacting Dacor. The rude customer service advisor first talked to me like a police interrogation, then said sorry cant help. A joke of company with cheaply designed products. Never again.

Dacor refuses to take responsibility for defects in their products. Our wall oven required two cooling fan motors and two relay boards over a relatively short period of time. In addition, all of the sensors had to be hard wired when the oven stopped working, and our service technician was informed by Dacor that moisture tended to get into the sensors on these ovens. We spent nearly $1500 on these repairs. Reaching a customer care representative at Dacor can take upwards of 20 minutes. Phone calls are not returned. Customers are left to pay the cost of defects in Dacor products.

I paid over $6000.00 for a Dacor EF48BNDBSS refrigerator and have had nothing but problems with this item and the other Dacor item (dishwasher) that I bought when I had a new kitchen built for my new life of retirement. The first refrigerator that was delivered did not work when it was installed and was returned immediately. I had to wait for Dacor to send another one and I have had to pay several service calls each time since that point. I am disgusted that I paid over $10,000 on two appliances from Dacor and neither of them has ever worked even at a low grade basic level. Both of my items have been discontinued and Dacor reimbursed me for half of what I paid for the dishwasher, which did not even cover all of the repair calls that I had paid for ongoing service. At that dealing, I got tired of paying for repair calls for the refrigerator due to excessive icing in the freezer; supposedly there was a quick fix right after I had the unit installed and it did not fix the issue. Now, there is another quick fix that Dacor suggests and that will cost me $800. Really? I dont think so. In fact, I have researched this issue and have found that this quick fix does not solve the problem either. In addition, I have called Dacor numerous times about the refrigerator door not sealing and the refrigerator making all kinds of strange noises. They told me it was the seal, so I had the seal replaced and that was not the issue. Then I paid $235.00 for a service call to look at the seal and he said that this refrigerator has known problems for hinge issues and he attempted to fix the hinge and left and the problem continued. Between the hinge issues, the constant icing issues in the freezer and the food icing over as well along with the trays and inner shelving of the freezer, the refrigerator sealing and the hinges working, and the constant crazy noises that the refrigerator makes, I am ready to file a lawsuit for a lemon of a product. This is the second product that has recall issues and multiple problems. I am sure that with my documentation, a judge would have no problem agreeing that I have paid way too much and put in way too much time and energy into getting a decent appliance into my kitchen. I would never recommend Dacor to anyone. I am dissatisfied and refuse to pay another penny for service calls on these appliances that were installed in 08/2012. At this point, my refrigerator is unplugged and unusable and I am using a small refrigerator that I bought at Costco for $300.00 thirteen years ago that has never had one problem.

Dacor ERD30s06BK/LP - thought reputation was good. Quality seemed outstanding. Like: Appearance; Dislike: Performance, Reliability, Serviceability, Quality of parts, Availability of parts. In a word: Dont buy a Dacor! Ive learned that if you have a repair person/organization you can depend on ask them to suggest the best appliance based on their repair experience and their ability to obtain parts. Dacor has already replaced range once. Oven interior cracked when self-clean was used. Stovetop burner ignitors frequently continue to spark after flame is established. Stovetop burners will sometimes extinguish when flame is low. This experience showed me that just because an appliance is expensive, it doesnt mean good performance or high quality. Because of the cost of replacement we have lived with the Dacor until the next major repair is not possible because of lack of available of parts or cost.

This range was installed in January 2003. The door on the larger oven was replaced soon after because it would not close tightly and still doesnt with the new door. I have always thought that the oven temperature is lower than it should be but have been told twice that it is accurate, tell that to the turkey. The heating element on the large oven was replaced 2 years ago. Four of the burners dont light and have to be lit manually, this has been going on for 10 years. The relay board has burned out and now has to be replaced, $800.00 fix. The technician just left and could not replace it, he couldnt access the tight spot that it was in and wanted to cut the barrier panel to get access to it. He decided not to do the job and told me to call Dacor to get another repair service, which I just did. I was prompted to write this after reading other reviews and remarks. I hope this helps someone out there to buy a different brand.

We placed the new Dacor appliances that we’ve purchased in our second home in Big Bear Lake, California. The fact is we were in our second home approximately 10 times in the first two years. We had trouble with our Dacor dishwasher from the beginning. When you close the door, it wouldnt engage unless you close the door a number of times. It became progressively worse to the point where we brought out another repairperson - this time a certified Dacor repairperson. He got the washer going for a few minutes, only to not being able to complete a full cycle. We received an initial $89.95 bill, and during another contact we would have to pay an additional $400-plus for a motherboard and labor. We contacted Dacor, along with the contractor, a number of times. We had the history of this dishwasher which is causing problems.Dacor would not make it good, even though we spent more than $10,000 on other Dacor kitchen products. It simply doesnt make sense to me to not fix a sub-par dishwasher to keep a customer happy. Now, we are angry and will go on a number of sites to advertise our plight. We will install a new Bosch dishwasher as we have no confidence in Dacor and even less in their customer relations division.

DCT305SNGH - I have owned this stove for about 3 years already. From the very beginning it has been trouble. The lights that turn on when a burner is on broke immediately. The place where the gas comes out and ignites is black and hard to clean. The grates are rusty, the finish has come off. The indicator knobs dont reflect what is happening in other words if it is on the lowest setting you dont have any indicator marking. It is hard to clean and scratches very easily. I have had the service person out about 5 times until they decided to send me many new parts. These arent any better. It is just a bad product. Basically the warranty is useless if you keep calling for the same issue. They say, This is the last time we will fix this issue. Sadly I always heard this was a great company and I waited 7 years to save up for this stove and boom rotten appliance.

Eight months ago I renovated my whole kitchen with all Dacor appliances, cooktop double wall oven, refrigerator and dishwasher and I could not be more pleased. I wanted to wait a few months before I wrote this review in order to make my review more accurate. I love the modern design of all the appliances. The refrigerator is nice and roomy and the cooktop has been very reliable. Dacor products cost a bit more but they are well worth the extra money!

After purchasing what I thought would be ovens of a lifetime I could not be more disappointed, frustrated and angry at a company in my buying history! Since November of 2014 and longer I have been fighting for service or answers or at least honesty! The ovens have never worked properly, they do not keep temperature. The oven temperature drops 60 to 75 degrees while cooking over a couple hours. The control board was replaced. Still the ovens never worked. If you like to cook and cook for the bed and breakfast, which is why you bought an oven like this, you will have your ovens on for a couples hours preparing any multi-dish meal! I was treated rudely on the phone during routine troubleshooting and was never allowed to speak to a manager. Dacor for months or so later is buying back my ovens minus a restocking fee, on ovens that dont work, $1200!

As an add-on to my original review, I had a a service call to address the LC error code. The service company reconnected my unit, turned it on, ran a couple tests, and declared there was no issue. We ran the dishwasher 1 cycle and it worked just fine. Tried to run it again later that day, and the LC code was back again. To resolve the issue, I worked with the company I bought my appliances through to replace the Dacor dishwasher with a Bosch. That happened today, so it is too early to tell say how the Bosch works, but it is more solidly built, has more capacity and the door fully opens with the panel installed.Dacor did reach out to me to try to resolve this issue, so kudos to their customer support, but the issues were just too many. And as I stated in my original review, love the Dacor range top, double oven and refrigerator.

This week Dacor installed my 2nd replacement gas range. I remodeled my kitchen 3 years ago and chose Dacor because I had a great experience with their appliances in the past, had their oven and stove in my kitchen for 15+ years and never had a problem. With the first new range, the oven started to automatically shut off due to excess heat escape, so the safety feature would kick in and shut the system down, in addition the knobs would become very hot even when the over was used briefly, 12-15 minutes. I was very impressed and happy with the customer service through Dacor, they immediately gave me a brand new over. Exactly another year, the new oven had the same problem, door begins to not hinge properly and heat begins escape, knobs get dangerously hot.This week Dacor very kindly, replaced my appliance with the new Dacor Renaissance 36. I used the oven for 12 minutes on 400 and the entire exterior is dangerously hot. I do not have any children, however, if I did I would be terrified that they could seriously injure themselves. The exterior of an oven should not become hot like this. Has anyone else had this issue with Dacor? I feel they have been very responsive with regards to customer service however I want an appliance that is safe.

Dacor 48 dual fuel range - Only 3 years ago, we purchased a Dacor range that is beautiful and worked great for 2 1/2 years. During the last six months, I had the led lights go out on some of my cooktop knobs and my oven has started not baking evenly, much as described in a previous post (half of your cookies can be burnt and the other half dough). A serviceman has been out twice and I have been made to feel that basically, I dont know how to use this oven or dont know how to cook. Funny that has only been in the last 6 months. I cooked great with the range for 2 1/2 years and have 20 years of cooking experience, but obviously, I dont know what Im talking about. To replace a led light bulb, I had to purchase a $300 control board part (that Dacor did discount) plus a $100 labor. It ended up being a $250 light bulb fix that has exploded to a potentially additional $600 problem. When taking off the range lid to replace the lights, I am now told that 3-4 burners have to be completely replaced and this again is my fault somehow because the metals fuse together and that is known by Dacor to happen, but my service tech said its because I dont clean my range well enough. This still makes no sense. And to fix the oven problem, it might be the control board? Lets throw my money at it and see? All guessing, the serviceman, Dacor, etc.! So now Im stuck with a parts bill of over $1,000 (Dacor did discount this to about $300) plus $200+ in labor, another guess. This just seems ridiculous to change a light bulb and guess at an oven fix for a 3-year old range that cost as much as a car! Im so irate over the whole issue! What a mistake Dacor was.

We have had our Dacor since 2006 and this range, the most expensive appliance we have ever owned, simply doesnt maintain the proper oven temperature. We have owned several far less expensive ranges and their ovens, much more basic designs, do what an oven is supposed to do maintain a temperature! We cook or try to quite a lot but working with this stove is like baking over an open fire while camping. This supposedly gourmet, fancy, convection oven that supposedly can bake cookies and meat at the same time is a total fail. We have had the service people out repeatedly to no avail. I am convinced we could change the circuit boards repeatedly and it wouldnt make a difference because it is a faulty design. This product should not be on the market or this company and their poor service in business. DO NOT BUY THEIR RANGES! Unless you dont cook and all you will do is look at it. We are thinking about retaining an attorney to file a class action suit. We could buy a low cost oven that works several times over for what we have paid in repair bills.

We remodeled our kitchen in the fall of 2009 and decided to purchase what we thought were higher end Dacor appliances (stove top, oven and microwave). Well, what a mistake that turned out to be. Considering the price we paid for the appliances, you would not expect problems from all 3. Perhaps a problem with 1 appliance, but problems with all 3 suggest a real quality problem. My first indication should have been when I called and asked how to change the green LED on the microwave to blue to match the nice blue LEDs on the oven mounted right below. I was told that someone else makes the microwave and Dacor just puts their name, and that I should just turn off the LED on the microwave. I dont know if that is true, but that is what I was told.Now when using the microwave/convection feature, the oven makes a noise (sounds like a fan motor) for the first 3-5 minutes then eventually quiets down. A daily reminder of the mistake we made purchasing Dacor. Then those nice blue LEDs on the oven started failing making it impossible to read the clock, timer or temp. Luckily, the oven still works; you just cannot read the LED any longer. This is a constant reminder of the mistake we made buying Dacor as we see the LED every time we walk into the kitchen.Finally, we have the solid surface electric cooktop. Although it works fine, the black paint on the metal trim around the stove top is wearing off. Now, we have some shiny metal and some black trim. This is just an annoyance and honestly, we probably would not have even complained about it. However, with the other problems we have had with Dacor, it just adds to our overall disappointment with Dacor. If I knew then what I know now, I would be a lot happier because I would have GE appliances and not these overpriced low quality Dacor appliances.

I could have written every one of these negative reviews. Ive had all the same issues with my Dacor Epicure oven. Faulty computer panel, failed motor in the downdraft fan, oven not maintaining temperature (meaning NOTHING cooks correctly in this oven), burned out lower element and discolored interior. And let me add that the interior oven fan stays on for about half an hour after you turn off the oven. What purpose could that possibly serve???? Suffice it to say that this is a poorly made product by a company that has no desire for repeat customers. I am currently working with customer service to try to get my oven working for Thanksgiving, but I just dont have much hope after reading all of these similar issues. Clearly, they manufacture a sub-standard product and sell it at premium prices. Nice business model, for a while.

Our new ranch has three Dacor microwaves, only one of which has had a few months of use. The others have very limited use. To this point weve not had problems, but given the opportunity to redo the purchases wed go with a popular brand, i.e., LG, GE, Panasonic. They are more flexible, parts are available, and all three combined would probably cost less than one of these. In fairness, I personally feel the same about our other high end appliances, Wolf, Viking, Sub-Zero and Asko. None beats our former appliances. Maybe its just about show.

Im planning a kitchen remodel and stumbled on this site. I have a Dacor dual fuel range (stove wont light, oven wont hold temp), hood (light wont stay on consistently), microwave (replace once, okay now), wall oven (panel out) and warming drawer. Only the warming drawer is working correctly. I live in rural Kansas and I cant get anyone to do repairs. I really like the design but... its time to move on to a new brand!

We have an 11 year old Dacor double oven with convection on top. The relay board malfunctioned and there are no parts to repair this. All Dacor would tell us is that they dont carry the parts anymore. Evidently, they are not required by law beyond about 8 years and that appears to be all they do. Our appliance repair person even contacted a company that rebuilds electronics and they cant get parts for this board. It is unbelievable considering what we paid for the oven. So we now have to replace it. Dacor offered us a discount on a new one. Not good enough. I cant imagine putting another Dacor product in. Two appliance service people have told me that Dacor has this reputation and they would not put them in their own houses.

I purchase a home with a Dacor double oven. Unfortunately the oven begins transmitting multiple beeps and the touch panel will sometimes read off after beeping a while. I contacted the staff at Dacor requesting a service manual. They refused to send me a service manual and stated that only authorized technicians can service their equipment. Its obvious they used google or a local phone book and sent me contacts of appliance repair shops in my area.When I called, they had never heard of Dacor let alone be factory authorized. I called Appliance repair shops up to 50 miles away to find there were no Dacor Dealers. I found one 70 miles away but it was too far to send a technician. If I remove my oven from the wall and take it there they would attempt to look at it. I had to reverse engineer the thing to find that my touch panel has gone bad and now I cannot find a used one. I want to recommend that anyone considering an appliance DO NOT PURCHASE A DACOR! If you are looking for high end stick to SubZero / Wolf. Oddly enough I see that there hasnt been any reviews for the past 5 years. Maybe it appears people have stopped buying Dacor appliances.

I bought a Dacor appliance package for a new custom home which costs over $30K+. Every single piece of appliance is defective. I am OK as long as Dacor can fix or address the issues but it takes them several visits, put the appliance out of order and fixing it does not happen any earlier than 8-10 Weeks. Imagine you living with a fridge, microwave, range and oven for 10+ weeks. The column freezer stops making ice. I call for service and tech informs the lever was jam and he fixed it. Wait 48 hours.After 48 hours still no ice. Another call and after a wait of 3 weeks another visit and diagnose need new part. Wait for part 4+ weeks and another 3+ weeks for replacement. Fridge does not cool and maintains temp 45 degree+. Service tech showed up 3 times and promised it is fixed. Have thrown out thousands of dollars worth food. To date I dont have it fixed. Waiting for a part, tech not available scheduling issues etc. To date I have been out of fridge (8/12/2021) 9 weeks from I made the first call. Currently I have a tech scheduled for 9/1/21.This is not the end. Microwave will run normally and wont heat the food. After several phone call and waiting they figured the door pin was not connecting properly and need parts to fix. After 10+ MONTHS it looks like it is fixed. The range control panel is hanging from underneath and no one seems to care to fix it. Every time I call they tell me its normal. I believe Dacor has not QA/QC in place prior to shipping the appliances to customer. Worst experience ever. If you need more details do not hesitate to call me on **. I hope you run away from Dacor. Dont even consider this option. I have a track of all phone call and email and timeline with Dacor service. I am planning to file a lawsuit and recoup some of the costs and losses.

I was a bit anxious when I purchased my Dacor range because I really didn’t know how it would perform. A year later and I couldn’t be happier. I love my Dacor 30” range. It has been one of the best purchases ever.

I purchased my Dacor wall oven in 2008 and have nothing but problems. I have had two computers replaced for over $1000 each and other boards replaced. Problems started just after the manufacturers warranty ended. I consistently get a U60 fan error message, no matter what Im cooking and no matter what cooking cycle Im on. It works for about 15 to 20 minutes and then stops and there is no way to restart or reset it.

Don’t purchase Dacor appliance - it’s been worst purchase experience ever and I am extremely disappointed. After six months since I purchased the Dacor built-in refrigerator, Dacor couldn’t even ship the proper installation parts and my refrigerator is still not working. Problems:1. Their high end $11K Dacor built-in refrigerator cannot even be installed. Wasted five months communicating with both Dacor and the retailer AppliancesConnection. After five months they were still able to ship the proper missing installation parts. Over the past five months, I talked to six different team members in Dacor customer support team, escalated to customer support lead and also talked to their regional technical manager, none of them is able to solve my problem and ship the right installation parts.a) Their process is extremely messy. Their customer support team had no idea about installation requirement of the refrigerator. And the request from their customer support team is declined by their internal Parts department again and again, only to find out installation parts should’ve shipped by the retailer. This is extremely confusing now and no one in the team seems to understand the right process.b) After Dacor acquired by Samsung, their manufacturing process is very messy and parts are extremely confusing. There’s one version of required installation parts in Dacor manual and one version of Samsung parts in the Parts guide, and no one in the team seems to understand the difference and how to map from one to another (they insist on sending me Samsung parts instead, claiming they’re compatible). I am now the expert myself to understand all their parts and able to identify many problems in their manual.2. As a high end brand, Dacor doesn’t seem to care about their customer at all. As a customer who did kitchen remodeling and had no refrigerator to use for five months, no one in the team seems to care about their brand or their customers. With this huge gap in the process, no one thinks about the problem from their customer’s perspective or shared empathy with me. Dacor as a brand is really bad and I am extremely disappointed in both their product and services.

Purchased a house with Dacor 2 Built in 30refrigerators that suppose to be under additional 1 year warranty after 2 year initial warranty expires, Both units were registered online and still showing being under warranty and the company refuse to take care of the issue. This is not how you treat customers and it tells that it does not matter if you buy $8000 refrigerator, you as a customer does not really matter. I am in the process of building another house right now and I was considering spending over $40,000 on Dacor appliances and that will definitely not happen since the company refuses to honor the warranty that is still active over broken door spring. What a shame!

We bought a whole new kitchen's worth of Dacor appliances - the Modernist line. It's too soon to review their performance, but so far they work well and look fabulous. Most importantly, I had an issue registering my appliances for warranty. I sent an email and not only did they resolve all my issues, registered everything for me, they also notified me I was eligible for an extended free warranty program, and they set it all up for me without any effort on my part. I wouldn't have even known if they hadn't done it for me. So far, I'd say that they have stellar customer service. When researching online before making the choice to go with Dacor, I had trouble finding information and reviews. I wanted to make sure and share my good experience since all too often people only share when they have had a negative one. I hope this is helpful to someone looking to buy!

Oh how I wish I never bought a Dacor! It has been nothing but problems. I figured I bought a lemon but after reading other reviews its just not a good product with not very good customer service either. I have had repairs every year, and even after repairs it still isnt functioning as it should. The first problem I had was the whole glass window blew out during baking, which seems to me is a huge liability. The company said that shouldnt happen but is out of warranty and would give me a discount on the glass. I thought that was better than nothing but then 6 months later the relay went out, then baking temps were all over the place in the oven so they said I needed a new motherboard and they said both ovens needed it. So those were repaired. Oh ya and the light in the bigger oven hasnt worked past the first year even after having the light changed and some electrical stuff done on it. Then I had the bulbs changed due to irregular oven temps. The temps are still all over the place to this day.The back right corner gets too dark. The front left doesnt brown and is a lower temp. Now Im having problems with the oven turning off during baking and when using broil in the small oven it causes the large ovens probe alarm to go on and offer at least for an hour. Dacor didnt help me with anything past the glass and its only been 7 months since the new motherboards were put in. I cant afford to buy a new oven at this time and so I only use the small oven mainly since the larger has so many problems. Do yourself a favor and never buy a Dacor!

This range has never cooked anything well, overlooked and undercooked. Several technician visits, board replaced, thermostat replaced, starts error messages and clicking all on its own. Recently the cooktop has exploded with a big BOOM 3 times. We finally turned off the gas and Im cooking outside with the camping stove and BBQ. I am so upset about the explosions that I am shaking. Today it exploded while all knobs were OFF. Im thinking about getting an attorney. IF my house caught on fire my insurance would not pay unless I do everything in my power to mitigate damages. No gas should work, but I would like to be able to cook in my beautiful kitchen with my granddaughter. Help!

Bought the DACOR WALL OVEN in late 2019. Top burner is over heating and burns everything, caused a fire in the oven. Can not even get any response from customer service. Warranty not worth the paper it is printed on. Stay away from DACOR.

My wall oven spontaneously heating to 800, will be fixed! Thank you, James of Dacor for contacting me again and for arranging for my wall oven to be repaired at no cost. When our oven is in top working order, we love the convection option and we love the internal temperature probe. The people at Dacor offer the friendliest service I have ever encountered and I thank you so much for that.

For the second time in 7 years our Dacor ERD 48 Range has failed us. Just in time for our New Years Day dinner. Neither of the two ovens will heat. We are now encountering the exact same problem. We spent $1000 the first time replacing the board. We cannot afford to do it twice.

When we recently remodeled our kitchen, we replaced our Dacor double ovens that we had had for 15 years. These were great ovens and not one problem with fairly heavy use, so we bought the Dacor Modernist double ovens. The ovens are usable, but they are the worst engineered product I have ever experienced. First, there is no clock on the stove because as I was told the clock would etch the screen if it was on 24 hours a day. Second, the sound the timer makes is so soft, even on the loudest setting, cannot be heard in any room but the kitchen, so I paid a premium price to carry a timer with me, so I know when my oven is done baking. Third, if I turn the oven light on, the timer either stops completely, or it resets to the original time. Fourth, the oven buzzes when it is cooking. Fifth the user manual is useless and there is no video or online information on how to use this oven that is not user friendly.Finally, I have talked to Dacor and have had the repair person here, but he knew nothing about this oven. I am sorry every time that I use this oven that I did not buy my other choice, which was the Woof double ovens, but we thought this would be wonderful product, like the wonderful product that our previous ovens were. We also thought Dacor was a family company, but is now owned by Samsung. What a disappoint these ovens have been. The engineering for this product is a disgrace for any company and I no longer see the Modernist products advertised and it may be because it is such a poorly designed product. I never met a computer that I did not love, but this is not the electronic wonder that was advertised when we bought the ovens.

Epicure Range, wall oven, microwave and fridge - When remodeling our kitchen in 2010, an appliance salesperson gave us a good deal on the entire set. We spent $20k on the Dacor appliances. BIG MISTAKE! Do not ever buy anything Dacor. We have issues with every single one. Where do I start? The ovens have gone out three times now and I have had to replace the main panel, now it will not heat at all. The refrigerator 42 built-in is a big piece of crap! We have had it serviced 4-times for everything. The entire fridge freezes over due to a design flaw. The fan in the freezer completely ices over. The ice door broke. The crushed ice broke. The plastic door for the butter broke. The shelves broke.The microwave has had issues and has had to be fixed. The oven temps were wrong. Fixed those myself thanks to YouTube. When talking to the service guy he said that these are cheap appliances with the Dacor badge, so you have to spend big bucks to buy them and big bucks to repair! Do yourself a favor and if you are thinking of Dacor run! I contacted Dacor and they are even worse to deal with. They did not care that their appliances are very unreliable. Never received a return call, email, or even a letter.

My wife and I purchased a new Dacor dishwasher, new Dacor range and new Dacor microwave oven. Unfortunately, the dishwasher never worked and were now going through the process of getting the unit repaired. A repair technician was sent out and discovered a new CPU was needed. Then once the CPU was installed, a new circulatory pump was needed. And finally, once the circulatory pump can in, the unit still doesnt work. Weve had the technician in four separate times (installation, tech inspection, CPU install, and circulatory install) and each visit is approximately one week between visits. Yes, were now going on four weeks without a dishwasher that we paid for. Beyond that, someone needs to be home each time they visit. So now Im without a dishwasher for four weeks and I have to take four days off of work so a technician cannot fix my dishwasher. When I called Dacor customer service and asked for a temporary unit until mine is fixed, they simply stated we dont do that. Dacor may be a premium appliance manufacturer but they do not have a premium customer service department. So buyer beware, if your unit has any problems Dacor will not rush, hurry or try to accommodate you. Im sure the unit will eventually get fixed but after a month of waiting, I believe Ive earned the right to warn others about Dacors business practices. We purchased the unit from Pacific Sales in Corona, CA. When we asked Pacific Sales for assistance they said it was a Dacor issue and refused to assist us. These two businesses will no longer receive my patronage.

We purchased a Dacor dual fuel oven range in 2008 in conjunction with an extensive kitchen remodel. It was beautiful and expensive. It has had innumerable problems. 2008: One of the igniters broke requiring replacement. 2014: oven stopped working, required new relay board. June 2020: Relay board again broke, oven stopped working. December 2020: Oven stopped working, heating element broke. These were serious problems each resulting in 1-2 months without an oven as the parts had to be special ordered. We have not had an oven since December 2020 (it is now March 2021). We are waiting for a replacement part. In addition, minor problems included a broken indicator light and burner grating. Dacor customer service was only moderately helpful, referring us to local repair companies that had difficulty obtaining parts. Dacor has told us that this should last decades but we are seriously considering replacing it after 12 years because it is very unreliable. I would not recommend a Dacor based on our experience.

I contacted James ** at Dacor. His attitude was excellent and he resolved my problem (deteriorating dishwasher racks) beyond my expectations. He was compassionate and understanding every step of the way. James followed through on his promises in a swift and efficient manner. I would recommend Dacor and James ** to anyone. He is an asset to Dacor and should be recognized for his professionalism.

It give the peace of mind, knowing that having a Dacor cooktop (RGC365) I have one less thing to worry about it. Food is always on time, and my wall oven is so simple to use and clean. Like I said one less thing to worry about it. I been a Dacor customer for over 12 years. There is no need to look any farther. My next kitchen will be a Dacor Set.

I got a fridge, a wall oven, a cooktop, dishwasher, wine dispenser and now I am picking up a wine cooler to compliment my wine dispenser. I like a variety of wines and I need a lot of storage space. I plan to buy more wine coolers. Being the top cat of me crew I need a image and style to keep up. Capiche. Ciao.

The oven I purchased is the Dacor double oven, model number - ECD230SCH, I purchased extended warranty on the ovens. This was purchased when I bought the ovens. I have renewed this and still have a warranty for 2 more years. I cannot get anyone to do the repair on this oven. My location is at the Sardis Lake. I cannot get anyone out to service. I do not know if you have any thing to do with this. I have had an oven out since June 2013. Please help, Dacor should have service reps in this area. I am in Sardis Ms.

As a contractor, we were fortunate enough to build our dream home which was completed in 2005. After much research and many show room visits, we purchased Dacor appliances for our kitchen. As the saying goes, if I knew then what I know now. Our biggest (note I said biggest, not only) issue is with our ESC130 oven. If you own this oven, do not, repeat, do not, use the self-cleaning mechanism. I have had this repaired once and then replaced once (along with a relay board). I seldom use this because I know when I do the lock mechanism will continue to cycle until it is replaced. This means, while I can still use my oven, I have to time when I open the door based on when the lock is cycling in the unlock position. I must also turn the oven off at the circuit breaker or listen to the continuous warning beep that the lock is cycling (as if I didnt know).After repairing this feature once, I next choose to have the mechanism replaced and Dacor offered me a discount on the parts (the oven was and still is out of warranty) at a cost of more than $500.00. This is on top of what I had already paid to have it repaired just 18 months earlier. I feared using this feature again as I didnt want a repeat performance. After cooking macaroni and cheese yesterday, I felt I really needed to clean the oven and made the mistake of using the self-cleaning feature of the oven. I dont know why I was surprised when the locking mechanism refused to stop cycling.I contacted Dacor today only to speak with the rudest customer service representative I have ever encountered, Steven. No last name. He is the only Steven who works there. He refused to listen to me, spoke over me when I did try to talk, and did not allow me to speak with anyone else. There are no supervisors available on Fridays and he could not transfer me anywhere. I left a message for someone else to call me (they did not). I called back later that afternoon and was given the name of a supervisor, Nhi. She was not available and I spoke with another customer service representative. I learned that Dacor is aware they have a problem with this locking mechanism and are trying to correct it. This got my hopes up, thinking that the company would now do the right thing and replace this mechanism at not cost to me, or at least at no cost for the parts. Not so. Even though Dacor knows there is an issue with this mechanism and they are supposedly trying to correct it, all they can offer me is a discount on parts. Really? Wow! A discount for a part that you know doesnt work properly and probably wont work properly because they are still working on the problem? I just really dont know what to say. Is this supposed to make me happy as a customer? Would prospective customers want to buy a Dacor product knowing that Dacor is more than happy to sell me a known defective product at a discounted price and they should expect the same? It is probably needless to say that I would urge all prospective Dacor owners to not waste their money on any Dacor product as they do not care about their customers. I will certainly be doing my part to warn others and hope this serves to warn others as well. Dacor has a lot to learn in terms of building even what could be called a good product and standing behind what they sell as well as becoming a customer service oriented company.

I bought DCM24S DACOR 1.5 CU CONVECTION MICROWAVE-SS and after few months of using this product its banded on the back wall of the microwave that supposedly resulted from improper turntable placement which caused the turntable tray to make contact with the back of the oven. The quality of the product is very poorly, dont buy Dacor product!

Dacor Fuel Range broken door - My Dacor is by now 13 years old. I see from other reviews that the problems I have with my range have not been addressed in newer models--the same problems exist. When I received my Dacor, there was a crack in the front, above the door. It was small, and Id just had a baby so I let it go. I noticed that the door did not close either, and because I did not address it within a year, Im out of luck. But youd think that making an oven with a door that closes snug would be a top priority. It only closes properly when in cleaning mode. My oven window became brown and I cannot clean it. Its a shame that these things are messed up because the convection seems to work wonderful and the oven is fairly attractive. If the door closed all the way. Im getting ready to consider a new oven. Wont be a Dacor.

We purchased a Dacor Epicure dual fuel range when we built our house 7 years ago. It was the most expensive appliance we bought and we wish we hadnt. We have had no problems with the stove top, but the oven, specifically the broiler unit has been a consistent problem. We rarely use the broiler and use the oven perhaps 2 or 3 times a month. Yet, the igniter had to be replaced in March of 2008 and again, in June of 2010. In January of 2011, the broil gas valve was changed and now in September, the broiler is again not working. I cant see pouring any more money into this appliance and will sell as soon as I find a buyer willing to take a chance on it. We have been greatly disappointed in this product.

We remodeled our home and purchased Dacor appliances for our kitchen. Range, love it, Microwave, 30 Double oven and warming drawer (promotional give away). The ovens from the beginning do not function well. To warm up the ovens I have to wait 45-50 minutes and it buzzes. It is at temperature but then when I look at thermometer we are close to 75 degrees below. It recycles temperature every 75 degrees too. We had many repairs to the original unit to the point the repair person recommended that Dacor replace the unit. They did, another disaster. First they dropped the old unit while removing it chipping my granite, destroying my drawer panel and then left an absolute mess. The second unit has the same warm up issues, holding temperatures and oh wait, fans ran for hours after they were turned off. Broiling amazing. Baking and convection, a joke.The last repair person told me to open the oven and turn the cookies to have them cook evenly. And do the same when cooking with Convection. :/ I am currently looking for a reliable double oven that I can use and feel good about the food I serve (to be cooked). Dacor basically said that they cannot help me anymore because we went out of warranty last year and sent a repair person to basically say it is acceptable. Obviously for someone who does not cook, just sayin.

I went to put something in the cabinet at the top of my built-in wall oven and noticed the cabinet door was warm. Then, I noticed the heat was coming from the top of the oven at the control panel. I am afraid of a fire breaking out in the cabinet now. The oven is less than a year old. We just remodeled our kitchen and installed the ovens in May 2012 and this is just June.

We used a new Dacor range vent only to have it go on and off. We called Dacor and they referred us to Desert Tech in La Quinta. The owner came out and said we needed a new unit for $775. We said just unplug it. He charged us $275 even though it took him less than 30 minutes. Stay away from Dacor AND Desert Tech!

We purchased a Dacor wall oven to replace a GE oven that was outdated. We thought we were getting a premium appliance, but after less than a year and just before the holidays it quit with a code on the control panel we couldnt find in the owners manual. We had a serviceman out and the cost of the part and the service call was more than we paid for the oven! It now sits there, useless and a reminder to never buy Dacor anything!

I just had an appliance repair company come out to let me know what is wrong with my Dacor Stove door, since it wont close. He said the hinges are needing to be replaced. He said that he replaces these hinges on Dacor stoves ALL THE TIME and that the company really needs to file a recall on these hinges and/or reimburse consumers who have these installed. He said these should not go bad like they do. That this is poor manufacturing on Dacors part and they are not being held accountable. I agree 100%. It is going to cost me with labor and parts almost $ 400.00 to replace these hinges that should not go bad with the age of the stove. Thanks.

We purchased a Dacor oven stove top. It is about 10 yrs old now. 3 years ago we had a problem with the ignitor and had it repaired and paid over $200.00 for the repair. 3 Years later we are experiencing a similar problem with the ignitors clicking on and not turning off. I have called for repairs on this but expect this will cost me some more money. I have been online and have seen similar complaints leading to believe that this is a common problem and I would avoid purchasing Dacor ignitor products for the stove top, until resolved.

When I completely remodeled my kitchen 6 years ago, I actually went AGAINST the advice of my appliance dealer and kitchen designer and insisted on buying the Dacor 30 double convection wall oven. Id been longing for Dacor ovens for years and though they gently tried to steer me towards Miele or Electrolux, I dug in my heels. Ive regretted ever since. Since first use, my electronic display has not been without an error message. Every time I go to turn on the oven, theres a message telling me to clean the convection fan filter. I called Dacor and they told me to ignore it! It was a mistaken message. Still, I cleaned them repeatedly to no avail. The main electronic circuit board on the oven has gone out three times. They paid for it the first time because it was under warranty. The second time they sold me the part at a discount but I had to pay for the service call. Total cost to me: $480. The third time, I had to pay for everything myself. Total cost to me: $870. They told me its because I broiled with the door open. I have NEVER broiled with the door open! The inside lights go on and off randomly. The temperature probe has NEVER worked properly. Last week, I was preheating the oven to bake some cookies and an alarm went off giving me a cooling fan error message. The oven turned off and I cant get it to turn back on. I called Dacor customer service twice so far and the first time they told me they would research the issue and call me back. They NEVER CALLED. I called again and they told me they could ship me the part and I could pay for the service call. The lower oven is currently working so I havent done anything yet, but the oven originally cost me well over $5,000. I have put another $1,300 into it. Im not about to spend another $500-$600 on this complete waste of money. Bottom Line: Dacor sells junk for exorbitant prices and refuses to stand behind their products. I was an idiot to fall for the Only True Convection Oven in the market line. Im buying a Miele or a GE to replace.

I had an issue with the wall oven light on my Dacor Preference double oven. To make a long story short, after contacting Dacor directly, they made sure that the unit was fixed by providing the part directly to me and confirming that the local repair company would be willing to install it. The oven is 8 years old and in the end, what I spent seemed reasonable to get a fully functioning oven (membrane switch). They were prompt, personal and courteous in their response to me. I came away feeling that Dacor takes pride in their history and their products! They also cleared up some misconceptions that I had regarding the status of their company. Although it was frustrating to have an appliance not work properly, I feel that the customer service Dacor provides makes their company one worth sticking with. That makes a big difference in todays impersonal world.

Updated on 05/12/2020: I wrote a review of our Dacor kitchen and gave the company a review of 2 stars because the cooktop, ovens, and hood blower all have failed at some point. The real issue is that the company doesnt support products after sale to quote them they do their best... The other problem is this site, it allows companies to claim they are or have resolved issues, without a response or comment from the customer about what the Companies Resolution entailed. Sending me an e-mail that says sorry the thousands of dollars you invested in our products only bought you up to 7 years of replacement parts, isnt what most people would call a Resolution. After months of working with the retailer and Dacor the e-mail below is what they consider a Resolution:Subject: Dacor customer service **Hello Mr. **, We would first like to thank you for staying a Dacor customer for as long as you have and would like to apologized for the inconvenience. As a manufacture we are constantly innovating products and at some point parts and units do become obsolete. Dacor does provide parts for as long as we possibly can. Once the appliance becomes obsolete we are only required to hold parts for up to 7 years. We again thank you for being a Dacor customer. Be safe during this pandemic. Have a great day. DENISE ** | Customer Service RepresentativeO: (833) 353-5483 x** F: (626) 403-3130Original Review: We built a new home in 2003 and purchased Dacor Preference appliances. Including a 6 burner cooktop, double 30 inch wall ovens, warming drawer, a microwave, and large hood with a remote blower. All the appliances are stainless. We enjoy home cooked meals and prepared at least one meal a day. Our kitchen is a work place not a show place. So these are my feelings after 16 years of use.The Cooktop has plastic knobs and a rubber gasket under each burner and piezo electric igniters. All of these items have failed over the years. I replaced the burners some years ago because when the gasket fails the burners sputter and liquid spills leak into the bottom of the cooktop. Replacement burners fixed the problem for a while but the burner design makes this a point of failure. Additionally, the burners were expensive so were back to sputtering burners and disassembly for cleaning. One of the plastic rings under the flame control knobs broke, weve ordered a new ring ($26) a couple of months ago but Dacor cant give us an estimated delivery date. For the past few years the Piezo electric starters only light half the burners, (they spark but the burners dont light) not a big deal but these are high end appliances, using a match to light the burners is definitely 1950s.The 30 inch double ovens are a great size for bakers like us. The Convection feature is great. However, the first time we ran the self cleaning cycle on the upper oven the door handle on the bottom oven bubbled and melted. The real issue with ovens today, is that Dacor has stopped making replacement parts including the electric heating elements. So even though we spent nearly $3,200 for these ovens, Dacor no longer supports them.The Microwave never worked correctly and we replaced it almost immediately. At that time Dacor used relabeled Sharp microwaves. Finally, Im not a fan of cooking smells in the house. So, we purchased 48 inch hood with a 10 inch inline blower. This week it failed. The motor hums but the fan doesnt turn. So replacement parts? Nope. If you decide to purchase Dacor be aware that the company doesnt provide support for their products in the long term.

This is our second Dacor wall oven. It is approximately 6 yrs old. December 22/14, I was cooking a Christmas turkey as per usual, and I noticed an odd smell about 40 mins. into cooking. Checking the turkey, the temp. was at 500 degrees and on broil. I burned holes in my oven mitts on the roaster taking it out. Even though I set the temp. at 325 convection roast, it reset itself to 500 broil. Nothing works except the clock. Called repair guy after the holidays. Said it is a control panel behind the keypad area. Ordered the part. Been waiting 4 months now for this part. Now, no Easter dinner either. After reading these complaints, I am worried that this part replacement may not be the end of it.

We remodeled our kitchen and decided to use the range as the focal point of the room. The decision to go with a Dacor ER36DSCH dual fuel range over comparable Wolf and Viking models as well as a Dacor heating drawer was made, a decision I have regretted since. Our unit keeps blowing the baking element ($200) which routinely fails at the most inopportune times. To date I have replaced four and the Mrs. recently informed me that the oven is once again not heating properly. Thankfully, I am competent enough to diagnosis and repair it myself and did a thorough operational inspection and cleaning which revealed the broil element ($180) had also gone bad this time. My wife hates this oven and unfortunately it sits right smack in the middle of our beautiful kitchen to remind us of the bad decision we made. In fact, we are now at the point where we are considering replacing it and sending it to a scrap yard where it belongs. Avoid this brand or it will cost you.

I spent a lot of money buying a Dacor double wall oven because it was supposed to be top of the line and dependable. Now, the circuit board needs to be replaced and the oven is just 5 years old! This seems absolutely ridiculous for an oven this young to have such a major problem! I am very upset about all the money I am going to have to spend to fix it. Ive never, ever had any oven problems with other brands like this in my life. We remodeled our kitchen and I thought I was getting something better and now I realize that this brand is not living up to my expectations at all! I am using an authorized Dacor repair company and they told me that they are seeing lots of problems with this brand. I do not recommend this oven to anyone.

I built my home in 2003 and installed a Dacor 30 wall oven. After several years of poor performance, we started to get an error message. Dacor suggested replacing a board for $300. That didnt work so they had me replace another $300 board. That didnt work so they told me I needed a new front panel and it would run about $1,000. That board is on back order and they dont have a replacement date. Thinking that its bad business to sink $1600 into a troubled product that has terrible reviews on the internet. We found out that once you go with Dacor, you need to stay with Dacor due to an unusual, nonstandard size.Thinking that Dacor has improved their product we ordered a brand new $3,000 Dacor RO130 30 wall oven. It arrived promptly and I removed the defective $3,000 oven and put in the brand new $3,000 Dacor RO130 oven. What I got was a dead brick. The Dacor customer service has been awful, and will not allow me to talk to anyone in their technical side. The oven is getting power. Dacor customer service wouldnt help me unless I could prove that the unit was getting power. So I had to get an electrician in to prove that I had properly wired the 4 cords that came off the original defective Dacor wall oven. Get service help? No chance. I live 100 miles from Seattle and no one wants to work on Dacor. So here I sit with a $3,000 brick. No service and Dacor has no clue on how they will service this wonderful $3,000 RO130 30 wall oven that is an out of box failure. I dont see how a company that has this bad of a product, two generations of defective ovens, bad customer service, reluctance from the repair community to work on their products will be in business much longer. If you are considering Dacor appliances, consider the problems that I am having. The nonstandard size of their ovens will lock you into future purchases to replace their products that dont last 10 years.