In 2010 we purchased a new Dacor Epicure Stainless Steel 42 refrigerator/freezer. Weve had to replace the freezer heating element (twice) because it fails and then the freezer ices up causing the system to stop cooling. This past week the fan began making a noise and so we had repairmen come out (yet again). Technician confirmed that the pan motor (fan in freezer) has failed. NO PART is available... I couldnt believe that parts wouldnt be available for a $10,000 high-end refrigerator that was purchased new only ten years old. I called Dacor directly and asked them how long they make parts available after they retire a model.The Dacor representative told me that they make parts available for 7 years. 7 YEAR PART AVAILABILITY ON AN APPLIANCE THAT SHOULD LAST 15-20 YEARS??? RUN AWAY FROM DACOR. Obviously customer service is low on their priority list. We will be replacing our gorgeous $10,000 ten-year old Dacor refrigerator/freezer (now a boat anchor) with Sub-Zero. Not too much more money than Dacor but they continue to make parts available for twenty years following model retirement. That is the kind of company that I want to do business with.

I purchased my Dacor Epicure Range 8 years ago when I remodeled my kitchen. My other appliances were made by GE and Bosch. Ive had to service my GE appliances a couple of times in the last 8 years, but it is the Dacor that has given me the most grief and it was the most expensive appliance purchased. It has never been reliable with regard to convection baking. Initially I thought it was my inexperience with a convection oven. I read everything I could get my hands on and kept trying...after talking with a friend who does quite a bit of baking I realized its not me, its my oven. Then the real problems started. First it was the broiler/ignitor, next it was the membrane in the keypad. Two months later it was the relay board and this time it was the broiler/ignitor....Again! Started calling Dacor when the relay board went out because at this point I had spent $1,000 on repairs....after I had paid $4,000 for the range itself. For the last two repairs Dacor has paid for the parts, while I paid for the service call and labor. This has reduced the cost of my last two repairs by about 50%, which is very helpful. However, Im still very disappointed in the product. I spend a good deal of time in my kitchen and do quite a bit of baking, cooking, and canning. I thought that if I spent more money and bought a high-end appliance, it would serve me well. At the rate that Im going, I will need to purchase another range, unless I want to keep throwing money into repairs on this one, which I dont. I will not ever purchase (or recommend) another Dacor product again.

Less than two years ago, we purchased a Dacor classic wall oven from a local high end appliance store in Durham, NC. Within a few months, the electronics started getting glitchy; the oven started beeping in the middle of the night. I turned off the beep, but other problems started popping up. I baked a pie which was half raw on one side and overcooked on the other side -- not exactly what you would expect from a nearly $5000 oven. Recently, the display has been blinking in codes and the oven has been turning itself off. When I tried to call customer service, I was repeatedly put on hold for 30 minutes after which the system disconnected me. When I finally spoke to a person, she was very rude. This is a horrible company, a horrible product and I deeply regret that the salesperson at the store talked me into buying this awful oven. I am extremely unhappy.

We love our Dacor 36 refrigerator. We have owned it for 6 years and never had a problem with it. Our friends and family have also complimented the look and style. We are happy with our purchase and would recommend Dacor products to anyone.

I completely gutted my kitchen on 2/22/92, and purchased a Dacor CPD230R double oven. Whenever I used the self-cleaning function the next day, F0 would appear. I would have to get a repairman to come to my house. This cost me a fortune. For one year, I just used the bottom oven. I finally called Dacor, and complained. I wrote a letter to Mr. **, and wanted satisfaction.They decided that I could purchase a new, better oven for $1,480.00. This was 1998, so in 6 years, I spent $3,680.00 for 2 ovens. After 5 years, I started having the same problems. Every time I used the self-cleaning function, F0 would appear. I just totaled my bills for the new, better oven, and I have spent $963.00 and it would be more, but I figured out, if I pressed cancel and held it, the F0 would disappear. So every time I used the oven, that is what I did. This would last for 8 months. The oven completely shut down, and I could not use the top or bottom. I just had a repairman here, and he said i need a new membrane assembly, and latch. They were supposed to call me with an estimate. They just called, and said the part is no longer available. This is upsetting. Reading the reviews, I see I am not alone in my dissatisfaction with the Dacor oven. Now, I will be redoing my kitchen.

I purchased the Dacor panel ready refrigerator and freezer column 15 months ago. The refrigerator stopped cooling -- in 15 months! These were 8k each!!! It had now been over 2 months without a working refrigerator and no end in sight. I will never ever purchase one of their products again! They replaced the compressor and 3 days later it stopped cooling again. What a joke! DO NOT BUY DACOR!

I completed a 7-month total remodel of our kitchen and family room, which were connected in November 2007. The kitchen remodel cost $18,000 for various Dacor appliances including the Millenia series of wall oven MOV130S; warming drawer MWDV30; and 42 island hood DHI42130. The remaining includes the huge 30 Epicure dishwasher ED30SCP, 36 cooktop EG366SCH, and beverage center EF24LBCSS. All have the beautiful copper accent package and make for highly attractive appliances. We constantly receive accolades for them. If only they werent absolute garbage functionally and reliability-wise. Others have remarked how the ignitors on the cooktop continually spark, even after the light off. After contacting Dacor and waiting 2 weeks for the repair, for which Dacor sent the wrong part and caused another 2-week delay, the repairman had to rip off the front accent lip of the cooktop to reach the base which significantly dented the front lip. The ignitor worked like a champ for 2 days, then click, click, click - constant ignitions. So I cleaned around the ignitor tip with 409, dried it and it worked flawlessly. Thanks Dacor for your own product ignorance and my now dented cooktop. It has worked well since and is a sound product, so far. If only my luck held out.Next, the wall oven. Very beautiful and my control panel has held out (fingers faithlessly crossed). The oven isnt calibrated though, so follow cooking directions at your own risk. This oven will burn your food if you set the temp and timer to the recommended settings. I have to take off 25-50 degrees and 5-10 minutes of requested cook time or I will smoke any meal. After 2 years of use, I decided to use the cleaning cycle - following the directions to the letter. Forty five minutes into the cycle and kaboo! The front window shattered. Dacor says $700+ for glass replacement; I say send me the part and Ill do it. I got the discounted part for $68; spent 3 hours cleaning and reassembling with care; and the window has held, but I havent tried the cleaning cycle since. Why roll the dice again?Ah, now my fave garbage Dacor appliance - the interminable dishwasher. Truly engineered by the diabolical. I just completed my fourth major repair after 5 years of use. First, the drain valve failed after a few months of use causing flood and was replaced under warranty. Then the door seal failed (more flooding) and was also repaired and replaced under warranty. The dishwasher stinks, by the way, as the unit cannot evaporate effectively during drying cycle due to ridiculously poor rear venting design. So I have to leave the door wide open for hours after use to facilitate drying and stench reduction. The control panel/circuit board has fried twice now in the last 3 years - it just starts erratically beeping and refuses to take input, even with a power reset. Both technicians stated the design and quality of the board is third world, which likely is exactly where Dacor outsourced the garbage.The island hood and warming drawer have worked well, and the beverage center has been reliable but maddeningly causes back left cans of soda to freeze and explode occasionally; even with the set temperature raised to now 45 degrees. Fun to clean up after coming home from a long trip. My expectations are so laughingly low now for these Dacor products that I dont bat an eye with the frozen soda muck this fridge occasionally produces. Customer service though has been helpful and thankfully, American. They have replaced both circuit boards for free well out of warranty. I have only appreciation and great sympathy for the customer service folks who Ive spoken with. I love my kitchen, but hate the appliances in it. Never again Dacor. Never again.

Arrived in good condition and so far works perfectly. Delivery was delayed by one day because of the incompetence of my local mail service. I bought this microwave, as others have described, to replace a 13 year old Dacor that had not really died but had lost the electronic screen. We put magic marker numbers on the display screen where the numbers had been 5 years ago and kept using all the functions. I decided to replace as, without the display screen, I could not do anything semi sophisticated with this microwave but its motor and microwave capacity was still going strong. This model fits perfectly into the previous 24/27 trim kit. Unfortunately our other trim kit is white to match our old microwave. Decor only has stainless steel now. And the new trim kit for this microwave is flat without the vent slats (plus costs over $300!). From the placement in our cabinet, I think the vented slats are really important to dissipate heat and am puzzled by the change in design by Dacor. The slats are a little tedious to clean but as a TV is above the microwave and an oven below I want the heat to have a better place to go. Ebay has the old trim kit in stainless steel but so far the expense seems excessive for just the outside piece. The internal support bracket for the new microwave is exactly the same as for the previous model so the only part of the trim kit needed for my microwave is the outside frame. This newer model works very similarly to the older version. I am delighted Dacor still makes this microwave to fit my space 13 to 15 years later.

Talked into spending $4700 on a wall oven on the recommendation of an appliance retailer. My concern was even baking and reliability. Was told I would be very happy as Dacor was best on the market. Well long story short, it never cooked evenly and after 8 years quit working. Had to lug the heavy oven to the city to an approved service provider. They thought it was the relay board (told the brains of the oven). Service provider changed several things (sensors, board and whatever else). Nothing solved problem. Phoned me and said I was looking at minimum $2000 and up. He threw oven in garbage. We didn’t even send the gas money to bring the dud home.Thought it should last longer than 8 years. I phoned Dacor. They wanted to know exactly what the problem and diagnosis was so I told them to phone the Service Provider. Said they would but I had to email copy of receipt which I did. A couple of months gone by and never heard a thing and they are not responding to my emails. DO NOT RECOMMEND DACOR.

We are in the process of remodeling our house including an entire new kitchen that we cant wait to finish to invite people over and show. HOWEVER, the cook top already has a light burned and finally the cover of it ended up falling as I was wiping down the stove (very softly by the way because I like to treat my appliances really nice). We have had this stove for less than a year I havent even made the last payment and it is already with a light burned out. REALLY? My husband spent countless hours researching the best appliances and decided to get this one and to come to find out that it is not good it is a complete disappointment. I am sooo upset. DO NOT BUY THIS BRAND!!! Save yourself the hassle that we are now going to go through trying to get a hold of someone on the phone and see what they will do if anything. I bought it from AJ Madison.

2017 purchased 36” range. First year- self cleaning overheated, replaced part. That was in 1 years warranty. But now: only 3 years barely: (I dont even cook much). Oven turns off by itself if I open the door. Oven does not turn off when I am done cooking. If I cook 450f pops warning of temp overheat. Called ABT service (this is where Dacor said) it cost $219 for a service guy to call dacor and to give me answer: I think it is android board. I have to buy a board. Plus per Dacor this board will not have wifi. So there is no Discovery- paid extra for extras I can not have...

Our refrigerator is 5 years old and has had a problem with icing up in the freezer area, resulting in a loud noise from the freezer fan. We originally called Dacor for service but they could not get to it for 2 weeks. An appliance repairman installed a new heater for the defroster. This only worked a short time and happened twice with a cost of over $1000. A couple of months ago, it happened again, and we were able to get a hold of ** at Dacor customer service. She knew exactly what was causing the problem. She ordered the parts and directed a factory-approved repairman to install over $800 in parts and we are confident the issue is resolved. Thank you, Dacor, for standing behind your products.

Bought the DACOR WALL OVEN in late 2019. Top burner is over heating and burns everything, caused a fire in the oven. Can not even get any response from customer service. Warranty not worth the paper it is printed on. Stay away from DACOR.

I recently upgraded my kitchen and had always heard that Dacor has been a reliable high end brand for kitchen appliances. Their refrigerators have a lot of space, and everything can be easily organized. All the appliances work as intended, and they also all look great. The stainless steel Dacor uses to make these appliances look smooth and clean, making it one of the most beautiful kitchen appliances I have ever owned. If you want a functioning kitchen with appliances that always look nice and shiny, then I would highly recommend Dacor.

The range cost over $7,000. In the first 2 years multiple malfunctions in the mother board, the convection oven functions, and had to hire a local company to repair. The Dacor company did not care. Called them multiple times, wrote them and received no assistance or response. Repairs cost $$$$ to fix each time something broke.

My Dacor wall oven does not heat. It is 6 years old and barely used. The technician is waiting for Dacor to get back to them to fix the problem. The technician has done everything they can and it has been four months and Dacor is not responding to fix the issue as its a Dacor problem not a technician problem. (Its a control interface issue, the relay board communicating with machine is not working properly.) I have done my own investigation and they do not reply to customer service e-mails, there is no phone number to talk to someone who could help, just a receptionist who says after 7 years we dont fix Dacor. Again, my oven is 6 years old. I would not purchase this high end product or any product from Dacor ever again.

We used a new Dacor range vent only to have it go on and off. We called Dacor and they referred us to Desert Tech in La Quinta. The owner came out and said we needed a new unit for $775. We said just unplug it. He charged us $275 even though it took him less than 30 minutes. Stay away from Dacor AND Desert Tech!

The electronics on the first two induction burners failed within six months which was covered under warranty. The second two went three weeks after the warranty and we had to argue with Dacor to cover them otherwise it is a $1400 repair job. From day one whenever you open the oven door the controls and heat shut off. Sometimes it turns back on when you close the door. As for the downdraft, it worked fine until 10 weeks ago when while closing, the cover lip hit a wooden spoon that had been lying flat near the edge. There is no safety feature and the motor continued to try and close the fan. The unit would not respond and would not re-open. The spoon had to be broken to get it out. If this was a childs finger you would have had to call 911. We now have a repair bill of over $350 and are still waiting for 2 months for Dacor to send a part. We will never buy this brand again.

We bought our new Dacor CPS 130S wall oven when we built a new house in 04. First we had to replace the lower heating element. Now the touchpad (Dacor part # 13290S) is malfunctioning. The + button will not respond to touch. Called Dacor and was told that the needed part number was discontinued in 2009. I double-checked with a distribution center in San Antonio, TX, who confirmed that the part is no longer available. They referred me back to Dacor on the chance that Dacor would have one somewhere. Dacors suggested solution was that we need to buy an updated completely new oven, which would cost us several more thousand dollars. So here we sit with a perfectly good oven minus a touchpad to control it correctly. So much for buying reliable, U.S. made products and receiving good service. I thought there existed a federal law that mandates a company must make parts available for 10 years if they discontinue the product?

DCT305SNGH - I have owned this stove for about 3 years already. From the very beginning it has been trouble. The lights that turn on when a burner is on broke immediately. The place where the gas comes out and ignites is black and hard to clean. The grates are rusty, the finish has come off. The indicator knobs dont reflect what is happening in other words if it is on the lowest setting you dont have any indicator marking. It is hard to clean and scratches very easily. I have had the service person out about 5 times until they decided to send me many new parts. These arent any better. It is just a bad product. Basically the warranty is useless if you keep calling for the same issue. They say, This is the last time we will fix this issue. Sadly I always heard this was a great company and I waited 7 years to save up for this stove and boom rotten appliance.

As I have read in most of the reviews, we have also experienced the control panel on our 30 inch dual range cracking over the years. We were told not to replace it because it would continue to happen. Ok, lived with that... Now something new has started to happen, the plastic handle on the oven door and surrounding area has started to melt. It got so bad after a self clean that it is collapsing. Now there isn’t much of a seal at all when the door closes. The stove isn’t brand new, but this has to be a fire hazard, and consequently, now the oven will not even turn on. I’ve reached out to Dacor with no response yet. I’m done with this company!

Would highly recommend not spending the money on Dacor. We spent big money on our kitchen hoping for years of trouble free service. We can no longer get parts for our Dacor gas stove/electric oven. The burners click for 2 minutes when you start them. We have gone thru 5 circuit boards. NO LONGER AVAILABLE. The oven light goes on and off by itself. Etc. Etc.

I called the customer service number regarding my double oven. It just randomly beeps and now turns off. No error code displayed. It has done this on and off since 2003. Now it is happening all the time. I called customer service and they seemed to act like it is my fault and I need a new touch pad. I inquired and this is a recurring problem with this model. I could not get a straight answer from the person I was talking to. He just told me that if the repairman says I need a new touch pad, then I need to get one. Well I have been doing some research and this is a problem that seems to be haunting more people than I. We own a Dacor gas cooktop that has had to have a switch repaired. We own a microwave that has had two new circuit boards and now a beeping oven that gives no error code and turns off by itself. My advice, do not buy Dacor appliances.

I have a Dacor refrigerator that cools poorly and needs servicing. Refrigerator manufacture date March 2017. When I acquired the refrigerator I signed up for the Dacor standard warranty (1 year) and the Promotional additional 2-year Dacor standard warranty advertised as 3-For-Free warranty. I contacted Dacor customer support by phone today. After an hour on hold, they said that they would have to check with their supervisor. 2 hours later I received a call back saying that its only a 2-year warranty. Their website where I registered my product (warranty.dacor.com/member) clearly indicates that my refrigerator is still under warranty. When I confronted them with this, their answer was anyone can register anything on the website and it proves nothing. In other words, registering your product offers you absolutely no protection.I provided their supervisor all documentation requested, (including proof of title of ownership of my house!), and they still repeatedly stated its only a 2 year warranty. When asked where they are getting this information, they simply said thats what we have in our system. I asked to speak to a supervisor, but they said none were available. I left a message with the supervisor, but none ever returned my call.Dacor continues to offer their 3-For Free warranty to this very day. As a busy physician, I keep good records and pay attention to detail. Dacor has been to my home previously without incident. I am extremely disappointed in what appears to be the companys blatant attempt to deny warranty coverage despite ample documentation that its still covered. I would caution folks that their 3 year for Free warranty is simply not true based on my personal experience today. I will no longer be purchasing any Dacor products because of this, and will relay my story to anyone interested in purchasing Dacor products.

We have a Dacor Epicure 36 six burner range. It has been a regular source of trouble since it was installed as part of a kitchen remodel in 2006. The igniter for the broiler went out 18-24 months after we got the oven. A year or so after that the weld that holds the bottom oven rack bracket to the oven itself popped loose making it impossible to use the lowest rack position in the oven. Last year the circuit board that controls, among other things, turning the bottom oven element on stopped working. Not only is the board itself quite expensive, but it is buried deep under the top of the stove taking lots of expensive hours of repair time to remove and replace. And now the burner igniters have begun to over spark (e.g., continue to click long after the burner has been lit, burners sparking that have not been turned on). The repairman tells me that is a different circuit board so we could be heading to another $500 or so in repair bills or perhaps a trip to the dump and a much cheaper replacement range. We have had other Dacor equipment (cooktop, wall oven, warming drawer) and have not had a problem with any of them. But given our experience with the Epicure I cant imagine ever buying another.

I built my home in 2003 and installed a Dacor 30 wall oven. After several years of poor performance, we started to get an error message. Dacor suggested replacing a board for $300. That didnt work so they had me replace another $300 board. That didnt work so they told me I needed a new front panel and it would run about $1,000. That board is on back order and they dont have a replacement date. Thinking that its bad business to sink $1600 into a troubled product that has terrible reviews on the internet. We found out that once you go with Dacor, you need to stay with Dacor due to an unusual, nonstandard size.Thinking that Dacor has improved their product we ordered a brand new $3,000 Dacor RO130 30 wall oven. It arrived promptly and I removed the defective $3,000 oven and put in the brand new $3,000 Dacor RO130 oven. What I got was a dead brick. The Dacor customer service has been awful, and will not allow me to talk to anyone in their technical side. The oven is getting power. Dacor customer service wouldnt help me unless I could prove that the unit was getting power. So I had to get an electrician in to prove that I had properly wired the 4 cords that came off the original defective Dacor wall oven. Get service help? No chance. I live 100 miles from Seattle and no one wants to work on Dacor. So here I sit with a $3,000 brick. No service and Dacor has no clue on how they will service this wonderful $3,000 RO130 30 wall oven that is an out of box failure. I dont see how a company that has this bad of a product, two generations of defective ovens, bad customer service, reluctance from the repair community to work on their products will be in business much longer. If you are considering Dacor appliances, consider the problems that I am having. The nonstandard size of their ovens will lock you into future purchases to replace their products that dont last 10 years.

We have a 2 year old 36 inch, Model EF361WF refrigerator. Water began pooling at the base every 2-3 days. Called Dacor Customer Service Team. Pitiful response and horrible customer service. Had to call private technician who was very surprised that a so-called higher end appliance was not factory-fitted with a P trap. He sees the problem often with cheaper models. Dacor has let us down twice. Buyer beware: sub-standard products matched with sub-standard customer service. Dacor will never get our business again and we would recommend all potential purchasers to consider other brands.

We purchased a Dacor wall oven when we renovated our kitchen in 2010. After five service calls, a replaced circuit board and broiler element, they found a broken wire which must have happened during clean cycle. I have been without an oven for two months and would not recommend buying a Dacor oven because I think it has a faulty design. The issue is still ongoing.

I went to put something in the cabinet at the top of my built-in wall oven and noticed the cabinet door was warm. Then, I noticed the heat was coming from the top of the oven at the control panel. I am afraid of a fire breaking out in the cabinet now. The oven is less than a year old. We just remodeled our kitchen and installed the ovens in May 2012 and this is just June.

The functions are useful and so far everything works the way it supposed to. No real complaints. Convection and baking features are really useful when it is a small thing to start an oven. Easy to operate. Everyday cleaning is easy as well.

Motherboard on my favor wall oven has been replaced twice. Repairman said not use the self-cleaning feature as that will cause too high of heat and melt the components. Seriously, Dacor? We spend this kind of money and have these type of repair issues constantly. Just glad I finally was told what might help resolve this - I’m ready for a new oven because of all these problems.

Purchased a Dacor freezer. Freezer does not come with outer panel. Understandably, because you can choose to put your own custom panel on or order one from Dacor. Found out Dacor was bought by Samsung, a few years ago. So I decided to order a Stainless steel door from Dacor. One of Dacors reps suggested I order from J@J international. I placed order and two days later they called back saying they cannot ship door to me UPS nor FedEx will ship it. They refunded my money, so I reordered from someone else. Got ss panel toe kick and handle. Opened box only to find out no hardware, brackets ss trim for sides screws and so forth. I assumed mounting hardware would be with door. So began the part search for parts. Come to find out Samsung changed Dacors part #s. Vendors who sell the parts could not come up with parts or told me not available. Reliable parts agent told me this. I was told they should have come with freezer. Meanwhile called back Dacor to someone who specializes in dealing with these issues. She took over 45 minutes of my time giving me the impression she was gonna resolve the issue. She finally said we have the parts and inferred that I must have not talked to reliable parts. I assured her I did. She continued to refute what I told her. I have been right at two months trying to get freezer door installed. I called an Appliance dealer in Salisbury Md. to get assistance. He told me when Samsung bought Dacor he dropped line. I now see why. It has been the worst experience I have had with a company that has absolutely done nothing but appear to be concerned and say they are sorry but do nothing. It looks like it will be another 750.00 to get a couple little trims and brackets and a few screws. If I had it to do over I would never have gone down this road. This has been a two month old nightmare that is still going on. Best advice I can give is steer clear of Dacor/Samsung. Was going to buy matching column refrigerator. Not now.

We moved in our new home in June 2019. We had purchased 2 Dacor dishwashers, 2 ovens, a gas cooktop and a microwave. All the appliances are beautiful. That said, both of our dishwashers leaked so bad we had to stop using them as they were damaging our wood cabinets and floor. Dacor sent service persons out after multiple calls and replaced the seals, but they still leaked. Our cabinet company that sold the Dacor appliances stepped up and replaced them both with Bosch dishwashers.Our Dacor Refrigerator went out in mid February and will not cool anymore. After 2 hours on the phone with a Dacor representative, we finally were able to schedule a service person to come out a week later (Dacor has very few support companies so dont plan on anything happening too soon when there is a problem). Was not able to repair the fridge and said it could be another two weeks to get the part and return. That said our service person is a great guy and cares, but has to rely and wait on Dacor for responses and parts.Our ovens take twice as long to cook as any other oven we have ever had. We are asking them to look into that as well. Overall, very disappointed. We understand having problems, but expect Dacor customer service would be much better and support their own field service persons and clients or at least act like they care. Not looking forward to calling them back to see why we need to be without a fridge for 3-4 weeks total....

I first bought the low-end Dacor dual fuel range and overhead microwave oven. Within the time frame of 3 years, repairs to the stove cost over $2,500. The stove cost $1,800. Ever single piece of plastic on the stove cracked and had to be replaced multiple times. The microwaves handle cracked 6 times, twice in one week. The overhead trim, which is about 30 by 6 and heavy, fell off and hit me in the head while I was frying bacon. If it had hit the pan of hot grease, I would have been burned. I contacted Dacor and got the brush off. I contacted Fight Back with David Horowitz about the problem. Dacor called me back, bowing and scraping, and we came to an agreement that they would take back the stove and microwave and put the full cost towards an upgrade to their high end model. I am sure you think I was stupid but the stove cooked beautifully and I thought a stove with no plastic trim pieces would solve the problem. Wrong! The microwave control panel has gone out twice, each repair costing around $350. The handle broke 4 times but that was covered under warranty. The front control panel has died 3 times (another $350 each time). The broiler dies each time the self-clean is used and that has been fixed 3 or 4 times. Some computer board on the top of the stove has died (another $400). The enamel lining inside has cracked, crazed, chipped off and rusted. Now, the front control panel has died and so has the one on the microwave. Times are very tough for us now and I cant afford to get them fixed. I noticed that the front panel trim on the top of the microwave is starting to pop out again (plastic fatigue). Hopefully, it will fall off again while I am cooking and hit me in the head and knock some sense into me. If it does happen, I will take them to court.

Liked the look of Dacor oven and fit in with remodel. Relay board replaced year after warranty - $600. Then after 8 years of light use (have Thermador home pro stove), another circuit board failed, part no longer manufactured. Oven now worthless and headed for landfill. Outrageous! Large national appliance retailer says Dacor not reliable. Daughter had major problems with Dacor fridge. Have purchased Kitchenaid replacement on recommendation of same retailer. Built to not last...shame on you, Dacor.

Dacor refuses to take responsibility for defects in their products. Our wall oven required two cooling fan motors and two relay boards over a relatively short period of time. In addition, all of the sensors had to be hard wired when the oven stopped working, and our service technician was informed by Dacor that moisture tended to get into the sensors on these ovens. We spent nearly $1500 on these repairs. Reaching a customer care representative at Dacor can take upwards of 20 minutes. Phone calls are not returned. Customers are left to pay the cost of defects in Dacor products.

We bought a whole new kitchen's worth of Dacor appliances - the Modernist line. It's too soon to review their performance, but so far they work well and look fabulous. Most importantly, I had an issue registering my appliances for warranty. I sent an email and not only did they resolve all my issues, registered everything for me, they also notified me I was eligible for an extended free warranty program, and they set it all up for me without any effort on my part. I wouldn't have even known if they hadn't done it for me. So far, I'd say that they have stellar customer service. When researching online before making the choice to go with Dacor, I had trouble finding information and reviews. I wanted to make sure and share my good experience since all too often people only share when they have had a negative one. I hope this is helpful to someone looking to buy!

As an add-on to my original review, I had a a service call to address the LC error code. The service company reconnected my unit, turned it on, ran a couple tests, and declared there was no issue. We ran the dishwasher 1 cycle and it worked just fine. Tried to run it again later that day, and the LC code was back again. To resolve the issue, I worked with the company I bought my appliances through to replace the Dacor dishwasher with a Bosch. That happened today, so it is too early to tell say how the Bosch works, but it is more solidly built, has more capacity and the door fully opens with the panel installed.Dacor did reach out to me to try to resolve this issue, so kudos to their customer support, but the issues were just too many. And as I stated in my original review, love the Dacor range top, double oven and refrigerator.

Updated on 06/14/2021: We placed a review about a month ago about a defective range. The company contacted us, took some information, but we have not heard from them since. It seems they just wanted an appearance of willingness to help but do not intend to help. After spending almost $4000 on a stove you would think it would last more than a few years before the motherboard malfunctioned. Dacor has provided no help. Very poor customer service and an extreme disappointment.Original Review: We bought our Dacor range for 3800$ in 2017. The self clean function did not work due to a defective locking mechanism. We had that repaired. Starting in 2019, the bake cycle was not heating up to set temperature. We followed recalibrate instructions. Then, the temperature went over the desired setting. I’ve tried adjusting baking times to deal with the problem. Convection bake started having temperatures above the set temperature.Several months ago we called for repair. The service technician tested the sensor and said it was fine. He stated that it was the motherboard which would cost $1200 to replace with parts and labor. That’s a lot of money to put into a high end stove that cost $3800 to begin with and is only 3 years old! We’ve had Frigidaire stoves that lasted 15+ years. This continues to be a problem. Unfortunately, we may have to replace this stove with Viking or Wolf. This is totally unacceptable considering the initial cost of the stove and the fact that Dacor markets their products to be long lasting and reliable. Never will I buy Dacor products again.

Purchased a Dacor DT0227B wall oven. The first oven arrived damaged; the control panel was completely off the unit. We ordered a replacement oven which arrived today. Upon turning on the power, error codes C76 and C77 appeared on the control panel display. The installers phoned your service people who instructed them to remove the front panel and look for a loose wire. When they removed the front panel, the entire control board was just hanging free, not secured in place with any screws (it appeared that this was an assembly error). They found a wire hanging, secured it in place, reattached the control panel and applied power. At this time the error codes were no longer displayed and they were able to set the time. When they attempted to start up an oven cycle to test the unit, the Start/Continue button on the membrane keypad was not responding. Another call to your service team determined that the control panel would need to be replaced. 2 ovens within 2 weeks arrived DEAD! The quality is beyond unacceptable. I sent an e-mail to the CEO of the company before I posted this. I received a response from a QA guy. Any manufacturing company that thinks Quality is the responsibility of QA is working with a 1950s mindset!! Dacor is pitiful and will certainly not last as a company with this kind of quality and customer service!!

We did a full reno on our house starting in 2018. With a brand new kitchen we felt higher end appliances would help finish it off nicely. We settled on Dacor from our appliance dealer due to the look a past history of great reviews. Had we known that the original Dacor no longer existed and it was now Samsung with Dacor nameplate we never would have bought them. We have had 15+ service calls for the fridge and oven. Oven didnt work from day one and required multiple board changes. The interior is not level so you cant bake a cake and the racks are impossible to remove without bending the rails. It just failed again last night just as the warranty expired. The call center is in the Caribbean so dont expect any help from customer service. The ice maker with the fridge is a continual problem so we had to buy an $100 ice maker that now sits on our counter full time. These appliances have a high end price tag but are not high end!

Dacor Distinctive Series Range model DR30D - One week after the appliance warranty expired, the oven stopped heating. The repair man replaced the circuit board. We still got a code 33 when we try to get the oven to heat to 400 degrees. Called customer service, they said to flip the breaker to the unit off for a few minutes. Seemed to help but we do not use the oven much, as we also have a Meile microwave/oven that we love and use that more. Then I cleaned the oven using only the ovens program. That locked down all of the gas cook top knobs. I called the repair service, it snowed on the Saturday of the appointment. They cancelled. I did not check the stove on Sunday. On Monday the repair service walks in and simply turns it on, no problem. VERY FISHY!!! I have heard the manufacture can control it by computer chips. This appears to be very true. Now the stove does not heat past 250 degrees. After speaking to a few people it appears this is a very common issues. Dacor is a lemon. Do not waste your time and money.

Purchased Dacor Renaissance wall oven in July 2015, Model RNO130S. After less than a year and a half, the cooking temperature began to fail. For instance, set to bake at 425 degrees, the oven would appear to heat properly, but tried and true recipes would be pasty and uncooked at the expected time. I inserted an oven thermometer inside to test and found an erratic pattern of oven heating up properly to 425 but then sometimes dropping back to about 350 during cook time and refusing to ever reach 425 again. ABT repairman adjusted temperature calibration but refused to troubleshoot any further. Just ruined another dinner. Thanks Dacor and ABT for your unreliable product and poor service.

The problem started with our refrigerator unit when it was still in the first year of a 2-year warranty. We have had over 9 service calls for various problems; we had to replace the circuit board, switch and the pan twice. The warranty runs out soon. After five unanswered calls to the customer service number, we were finally able to get through; not that it made a difference. Their response was, “We apologize, but there is nothing we can do?” Sound familiar? Dacor refuses to extend the warranty even though the problems seem to be bad design, parts and customer service. Dacor says when (not if) you need another repair, well work with you. Yipee! We get to work with them some more and pay for the privilege. Dont make the same mistake we did. We will never buy a Dacor product again.

Dacor Epicure Dual Fuel Range and Microwave - Where to begin? Perhaps at the end is best. Dacor appliances are shoddy, unreliable, outrageously expensive to repair and there is no customer support. That about covers it. We bought the above noted pair during our kitchen renovations 8 years ago. We thought that Dacor was a premium brand that would give us long trouble free service. How wrong we were! The only thing Premium about them is the price. 4 years ago, the microwave door refused to latch. Thanks to YouTube, I found out how to remove the door backing and found that the plastic part that comprised the latch was broken. Dacor was contacted - they no longer had the part. Try the open market I was told. I managed to jury rig a repair by using a wooden shim. 3 years ago, the range packed it in. Another repair - this time I was told it was the circuit board that had failed and which was replaced to the tune of $700 and I was cautioned that the second circuit board was not working very well - the interior light would not illuminate and the blue lights indicating a lit burner didnt work, and I should change it too. The smaller circuit board was costed out at $400. Last week, the door latch motor failed and the range began to beep incessantly. Now the oven cannot be used and repair costs quoted over the phone were in the 1000$ range. Thats it for us. Dacor is junk and belongs where its headed - the junkyard. Dont buy Dacor. Live and learn I guess.

I purchased my Dacor Distinctive #DT0127 wall oven in 2015 and have been very pleased with the product to date. However after running a self-clean cycle the oven does not work which was a surprise given the fact that I had previously done self-cleans before without any problems. I immediately contacted Dacor customer service who were amazing! The CSR that I spoke with kindly extended my warranty until 2018 even though I had not registered my oven with them upon purchasing it. He also arranged a service call for me that would be covered under the extended warranty. I am very impressed with the companys attention to service as I really love my oven. Even though I experienced this issue I would still recommend this product.

Warning: Warning, safety hazzard for all, adults and children. Recommendation: The knobs should be set on the top of the stove, not the front where children can reach. Control knobs should click when fire and gas is turned off, and highest flame setting should be at the end of the turn just like a clock. I inherited this range as new owner of the house. Today I used the high flame option of the gas stove. When I was done with cooking, I turned off the gas according to the knob position, front of the turn. Later I discovered the range was not exactly off. It was still hot but no flame could be seen.I checked by sight the control knob position, it was set incorrectly in off. Then I touched it and realized the knob actually has a bit more to go to the end, slightly before the off position. Therefore it continues to release gas with unobservable flame. This knob does not click when user turns it to the off position. It is just a silent knob with an inaccurate cue of a heavier black line for off and on indication. Besides, high flame setting comes at the beginning of the turn of the knob rather than the end, it is counter intuitive to our mind of increase heat by turning the knob further on, like our clock. Oven racks are hard to put back after cleaning. Once a rack almost tumble out while food was sitting on it.

Dont waste your $$ move on to another MFG. I have owned this dishwasher for some time it never worked anywhere near what I paid for it. The glides fell out of the racks. It never finishes a cycle. I have spent $350 for repairs three times and it is still way less than satisfactory. Move on, try a Maytag, Bosch or Miele. Also parts are astronomical and you will need them. If you are thinking about buying this brand google it and read on. We all have the same opinion of the Dacor Dishwasher thumbs down.

Dangerous condition! I purchased a Dacor 36 dual fuel range 5 years ago. I reported the issue to Dacor via email with no response from customer service. I believe the no response was an attempt by Dacor to distance themselves from their responsibility for this potentially dangerous condition. Specifics: When pre-heating the oven in convection/bake mode, if the oven door is opened before reaching the set pre-heat temperature, a ball of flame will explode up from the opened door. The ball of flame is basketball sized and has singed eyebrows and hair on several occasions. To reiterate - it is a ball of flame, not super-heated air that is the problem. As a result, after non-response from Dacor, we called a decor qualified repair technician who diagnosed the problem as a bad igniter. The igniter was replaced and the problem still exists. I fear that a small child may be severely burned by the engineering design fault.

I have own my range for about 2 years and for the most part it is used every day. I love the simmer burner and how strong the rest of the burners are. My food always cooks well both on the stove top and in the oven... I love this range.

We have a new (one year old) home with Dacor appliances. The microwave oven went on the blink the first month but was repaired by a factory approved repairman. Something to do with the computer. Now the double oven will not hold a temperature. We set the oven at 420 and it only goes to 360 even though the readout shows 420. We just decided to skip the repair process and bought a new Wolf oven. This is our second Dacor within the past two years and both have had the same problem. Dont waste your money.

We purchased a complete kitchen with Dacor Modernist stainless steel look. It has been a complete disaster since install day. The first week the Dishwasher flooded my kitchen causing water damage to my brand new kitchen cabinets. There was a seal issue. My ice machine has been worked on 6 or more times. They have replace every part in it and still doesnt make ice or if it does it freezes in to one big block of ice. My microwave combo oven just broke again today with same error code as last time. They had to replace both motherboard in the oven and microwave. Tomorrow they are coming because my dishwasher never completes a cycle. It shuts off at 16 min left. I have been asking for replacement units or better yet take it all back...I would not recommend Dacor espcially how much we paid... over 30,000.

Dacor customer service contacted me and worked with me and the appliance repair company to get the proper parts to fix the oven. Everything is fine! We once again really love our Dacor wall oven.

We purchased the Dacor modernist Refrigerator, after waiting several weeks to get it installed we noticed the water dispenser did not function properly, we contacted the retailer whom we purchased the appliance from and after several back and forth emails to verify our proof of purchase they put us in touch with a repair technician. After a few days they came to our home to review the issue and noted that this was a known design issue with the refrigerator and that our house water pressure maybe too high and they would have to come back out and install a special valve to fix the issue. Later they called and said Dacor will not acknowledge this as their issue and to call a plumber. After spending over $20k on Dacor appliances I would have thought their white glove VIP customer service would be better. Buy Viking!

I purchased a Dacor range hood 3 years ago. I had an intermittent problem from the start, as one of the two lights would intermittently go off. Replacing the bulbs didnt fix it. As one light worked perfectly, it became a tolerable issue. Finally, I was having other electrical work done in our home & I asked my electrician to look at it two weeks ago. He figured out that it was a defective lamp housing that incorrectly held the lamp bulb. Dacor shipped me a replacement lamp housing for me at no charge. I installed it this last weekend and it is running fine. Thanks, Dacor!

This is our second Dacor wall oven. It is approximately 6 yrs old. December 22/14, I was cooking a Christmas turkey as per usual, and I noticed an odd smell about 40 mins. into cooking. Checking the turkey, the temp. was at 500 degrees and on broil. I burned holes in my oven mitts on the roaster taking it out. Even though I set the temp. at 325 convection roast, it reset itself to 500 broil. Nothing works except the clock. Called repair guy after the holidays. Said it is a control panel behind the keypad area. Ordered the part. Been waiting 4 months now for this part. Now, no Easter dinner either. After reading these complaints, I am worried that this part replacement may not be the end of it.

My Dacor Preference 30 double wall oven (model PCD227R) was installed on 5-14-2004. On 12-31-2007, I replaced the upper oven high limit switch for cost $146.56. On 5-19-2010, I reset the lower oven high limit switch for cost $95.00. On 8-27-11, I replaced main control panel (Bezel Assembly), whose parts cost $271.10. On 12-14-2011, I replaced the main relay board for $214.02. On 1-16-2012, I replaced main relay board again, and it is under warranty. On 2-3-12, I replaced upper oven temperature sensor for $32.09. I am awaiting authorized Dacor service technician to calibrate both ovens.

We did a major remodel in 2006 and were talked into Dacor Appliances by the kitchen planner. Big Mistake! The first time we tried to do the wall oven self-cleaning, the circuit board blew out. Since it was just past warranty and no one near us in West Virginia would work on it, I found a board online for $200.00 and replaced it. It has never heated evenly and now it wont heat past 350 F and maintain temp. The Dacor range hood sounds like a jet plane and the variable speed switch wont reduce rate. The bulbs burned out and after buying two online for $30 each, I removed the decorative housing and use a more standard $10 bulb. The Dacor gas cooktop is OK except that EVERY time you turn on a burner, one or two of other igniters start clicking and wont stop until you find which one it is (not always the same) and turn it on and off. Please heed this and all the other warnings from the choir. DO NOT BUY DACOR! It is all very expensive junk! I only gave it 1 star because there was no way to rate Dacor a zero!

We purchased a Dacor Epicure dual fuel range when we built our house 7 years ago. It was the most expensive appliance we bought and we wish we hadnt. We have had no problems with the stove top, but the oven, specifically the broiler unit has been a consistent problem. We rarely use the broiler and use the oven perhaps 2 or 3 times a month. Yet, the igniter had to be replaced in March of 2008 and again, in June of 2010. In January of 2011, the broil gas valve was changed and now in September, the broiler is again not working. I cant see pouring any more money into this appliance and will sell as soon as I find a buyer willing to take a chance on it. We have been greatly disappointed in this product.

We purchased a under counter Dacor oven. The timer started given problems, tried contacting Dacor. The rude customer service advisor first talked to me like a police interrogation, then said sorry cant help. A joke of company with cheaply designed products. Never again.

Updated on 05/12/2020: I wrote a review of our Dacor kitchen and gave the company a review of 2 stars because the cooktop, ovens, and hood blower all have failed at some point. The real issue is that the company doesnt support products after sale to quote them they do their best... The other problem is this site, it allows companies to claim they are or have resolved issues, without a response or comment from the customer about what the Companies Resolution entailed. Sending me an e-mail that says sorry the thousands of dollars you invested in our products only bought you up to 7 years of replacement parts, isnt what most people would call a Resolution. After months of working with the retailer and Dacor the e-mail below is what they consider a Resolution:Subject: Dacor customer service **Hello Mr. **, We would first like to thank you for staying a Dacor customer for as long as you have and would like to apologized for the inconvenience. As a manufacture we are constantly innovating products and at some point parts and units do become obsolete. Dacor does provide parts for as long as we possibly can. Once the appliance becomes obsolete we are only required to hold parts for up to 7 years. We again thank you for being a Dacor customer. Be safe during this pandemic. Have a great day. DENISE ** | Customer Service RepresentativeO: (833) 353-5483 x** F: (626) 403-3130Original Review: We built a new home in 2003 and purchased Dacor Preference appliances. Including a 6 burner cooktop, double 30 inch wall ovens, warming drawer, a microwave, and large hood with a remote blower. All the appliances are stainless. We enjoy home cooked meals and prepared at least one meal a day. Our kitchen is a work place not a show place. So these are my feelings after 16 years of use.The Cooktop has plastic knobs and a rubber gasket under each burner and piezo electric igniters. All of these items have failed over the years. I replaced the burners some years ago because when the gasket fails the burners sputter and liquid spills leak into the bottom of the cooktop. Replacement burners fixed the problem for a while but the burner design makes this a point of failure. Additionally, the burners were expensive so were back to sputtering burners and disassembly for cleaning. One of the plastic rings under the flame control knobs broke, weve ordered a new ring ($26) a couple of months ago but Dacor cant give us an estimated delivery date. For the past few years the Piezo electric starters only light half the burners, (they spark but the burners dont light) not a big deal but these are high end appliances, using a match to light the burners is definitely 1950s.The 30 inch double ovens are a great size for bakers like us. The Convection feature is great. However, the first time we ran the self cleaning cycle on the upper oven the door handle on the bottom oven bubbled and melted. The real issue with ovens today, is that Dacor has stopped making replacement parts including the electric heating elements. So even though we spent nearly $3,200 for these ovens, Dacor no longer supports them.The Microwave never worked correctly and we replaced it almost immediately. At that time Dacor used relabeled Sharp microwaves. Finally, Im not a fan of cooking smells in the house. So, we purchased 48 inch hood with a 10 inch inline blower. This week it failed. The motor hums but the fan doesnt turn. So replacement parts? Nope. If you decide to purchase Dacor be aware that the company doesnt provide support for their products in the long term.

I have an Dacor column fridge and after 18 mths (under warrant), its not cooling. Its been 3 weeks, 2 repair visits and Im still out of fridge. Repair person said this is a known issue. If this is the case, Dacor should be proactive and reaching out to consumers under warranty to get this fixed instead of waiting for complaints. Interior trim kit is not included in purchase price which is ridiculous for the price of this fridge. Would not recommend!

We had a ongoing problem with a wall oven that was purchased in 2006. The most recent complaint was a oven glide rack that was not working. After complaining about it to one of their staff, they listened to our frustration and are sending us a new rack at no charge. My hats off to the great people at Dacor. Thanks for your understanding. Al

Purchased Dacor Induction Range w Convection Oven RR30NIS-C in October 2013 and LOVE this range. Accidentally broke the glass on the induction cooktop with falling object mid-March 2020. Only the glass is broken, and all other electronics, induction burners, oven, etc are functioning fine. Called Dacor support to acquire part number for a glass top for repair - obtained part number #701751 superseded by #702285, BUT was informed that the part had been discontinued and is no longer being manufactured or kept in stock. No other advice was given other than to discard the entire $6000 range. Multiple phone calls with service.I asked for a listing of third party part distributors and was referred to four distributors on the Dacor public website and given no other info. I called all web-based third-party distributors I could find in USA and Canada to see if anyone had the part in stock, with no luck. I contacted two technicians to see if they would be able to obtain the part through their channels, with no luck. I am an engineer, so I spent some time pouring over technical manuals trying to find a solution to replace the entire induction range cooktop assembly (top part of the range) with a later model, and although its possible, Dacor would not provide the ability to purchase an RNR30NI range cooktop assembly that could be fit into the existing housing on top of the range. The convection oven is completely fine, and I cannot believe that Dacor has given me no other option but to pitch a six-year-old $6000 range because they stopped manufacturing one fragile part made of glass. I would imagine that many consumers may be in the same position as I, as these cooktops are breakable, and accidents happen. I have reached out to Dacor support desk numerous times without resolution, and I am at my wits end with a $6000 boat anchor in my kitchen. What a waste of money! Poorly done Dacor!I would like Dacor to provide me with some sort of solution whether it be the part required to fix my induction cooktop, or a replacement Induction Range with convection oven, or reimbursement of the purchase price so I can obtain a replacement on my own. If I am not able to find a solution to repair my range, I will never buy from Dacor again! Dacor will discontinue easily broken parts without warning! You may spend thousands of dollars and not be able to repair your appliance after warranty expires!

The wall oven’s glass was damaged by a guest. Customer service at Dacor was exceptional. Within a day of advising Dacor’s customer service, I received a call from the service man and the replacement was installed the very next day. The service man was considerate by calling first and coming exactly when he said he would. He was very professional as he replaced the glass in a matter of minutes. I would choose Dacor again.

We have a dual fuel Dacor oven purchased in 2001. We have the manual. For some reason, after cancelling a timer, the oven locked at :4. The owners manual was no help. The Dacor website was no help. We turned off the circuit breaker then turned it on again and finally, the oven worked.

We have had our Dacor since 2006 and this range, the most expensive appliance we have ever owned, simply doesnt maintain the proper oven temperature. We have owned several far less expensive ranges and their ovens, much more basic designs, do what an oven is supposed to do maintain a temperature! We cook or try to quite a lot but working with this stove is like baking over an open fire while camping. This supposedly gourmet, fancy, convection oven that supposedly can bake cookies and meat at the same time is a total fail. We have had the service people out repeatedly to no avail. I am convinced we could change the circuit boards repeatedly and it wouldnt make a difference because it is a faulty design. This product should not be on the market or this company and their poor service in business. DO NOT BUY THEIR RANGES! Unless you dont cook and all you will do is look at it. We are thinking about retaining an attorney to file a class action suit. We could buy a low cost oven that works several times over for what we have paid in repair bills.

I recently complained about my Dacor dishwasher that would stop running during the cycle because of a faulty circuit board and touch pad. The repair would have cost me $500.00 to replace the entire touch pad and circuit board and the Customer Service department was not in the least helpful or concerned. After making the complaint on this site, I received an email the next day from James who was very nice and asked for the model, serial number of my dishwasher and who was the repair company I used. I emailed the information back to him and after verifying my information, he informed me that the parts would be shipped to my house at no cost and I would only have to pay for the service call! Now that was great service from a company who is trying to make good for a bad item in their appliance line. My repair person told me that Dacor is now using a different manufacturer for their dishwasher so hopefully it will be a better product.

I purchased my 30 range and was so excited! Well no longer. First the wrong range was delivered. I had to wait another three weeks for the correct one. My oven can not cook at all. Temp fluctuates by 100 degrees. Going on my third service call and still not working. It very unfair, I have to take time off work to wait for repair person, then nothing is fixed. I wish I could return this lemon. But after reading other reviews I am not alone. Why is this company not accountable for ripping hard working people off. I love cooking. Its my passion. My Kenmore Elite was half the price and far more superior.

Im on my second Dacor 36 range! I absolutely love this product. The large grates on the cooktop allow me to have multiple things going at the same time and the size of the oven is amazing. The oven takes a full commercial sheet which allows me to cook 3 or 4 dozen cookies at a time! Dacors convection system is undeniably the best in class. I can roast garlic and bake a cake at the same time with zero flavor transfer! My turkey at Thanksgiving is so amazing Martha Stewart would adopt me if she could see it! It truly makes the kitchen the heart of the home, not only is it aesthetically pleasing but it is the center of all things yummy at our house!

Dacor double oven range turns off by itself while baking - Disappointed in Dacor, especially today. Thanksgiving 2016: baking turkey. Sill baking turkey. I dont know when the oven decided to switch off this time, but I have an uncooked turkey and guests waiting. The oven has done this before, but because it was new I thought it was user error. Nope, the damn oven mysteriously turns off on its own. Incredibly irritated with Dacor. The range hood we also purchased is a joke. We remodeled our kitchen 1 year ago and wanted quality appliances. Bad move. Save your money, folks. Save your money.UPDATED ON 03/10/2017: Dacor sent a company out to fix the broken new oven. Oven still cannot hold its temperature (It takes FOREVER to heat then loses its heat while still showing a high temp). This time I have a recording on what happens when the oven automatically switches off. Disappointing when we spent nearly $10,000 in Dacor appliances for a kitchen remodel. DACOR, please have a rep contact me!!! Still waiting to hear back!!!

Do not buy a Dacor appliance unless youre okay with replacing parts for the oven in less than 2 years. The control electronic part was replace then less than a year later the user interface had to be replaced. Less than a year after the user interface was replaced, the oven completely stopped working. After calling the same repair guy to come fix it, they informed me that the company no longer sells the control interface. When I called the company, the only options they gave me were to send the part to a third party refurbish company and have them fix it. That means I would have to call the service repair company for the FOURTH time to have them remove the part, I would need to send it away to get fixed and call them back to put it back in. Dacor didnt even offer to pay for any of this. The customer service rep offered to give me a discount on a new unit. Are you kidding me?!? Please do yourself a favor and dont buy anything from this company. They dont back up their products and its clear they dont care about their reputation. Its a waste of money to be spend on high end appliances that are poorly made. Spend less from a different company thats been around for a long time. At least if a part goes, youll have reassurance they will have that part handy. A terrible company. I hope they go belly up soon so they can stop selling overly priced kitchen appliances to people.

My Decor Epicurian oven and range has been a nightmare from day one. I have had the oven for about 8 years and had it repaired so many times I have lost count and had spent at least $2000 on repairs. We have experienced motherboard burn out, membrane failure, temperature control malfunctions, error messages that cause incessant beeping. Nearly all of the problems that have been described in this list of complaints, I have had the problems themselves multiple times! Now, I am panicking a bit because I decided to use the self clean function on my oven this morning and now, I have read some sad malfunction stories following the use of this feature. I am so torn about whether I should just cancel the cleaning process. I do not want to risk having the oven malfunction again, but the thing really needs to be cleaned.

One year ago I completely changed out all appliances in my kitchen. My favorite of the four appliances is the range. We have enjoyed all kinds of new cooking techniques. As my wife put it, I did not realize how crappy my previous range was. Gourmet cooking is what Dacor is founded on and we could not be happier with the performance. Our favorite feature on the refrigerator is the in door water pitcher. Fresh cook water that can be taken to the table and refilled upon placing it back in the refrigerator. And the combi-microwave is an incredible second oven. All products have performed as advertised and promoted, and with a three year warranty whats not to love? Thanks Dacor for making amazing beautiful appliances.

Purchased a Dacor Epicure ER36DSCH/NG RANGE and oven in 2007. Sad story, it never worked properly since day 1. Initially a gas burner did not light, they came and repaired it. Subsequently the door lock failed in the lock position - had that repaired. The door lock failed the next year again, this time thanksgiving, ruined the dinner. They fixed it but the following year the lower burner element failed at Thanksgiving. All my relatives know not to purchase a Dacor product. Problem is I am stuck with this boat anchor. The oven door motor has failed 3 more times and thankfully the service man showed me how to change it. Today we tried to bake some apple pies and found the oven temperature set at 450 was only 350 (bought an oven thermometer). This explains why it always takes so long to bake things. A complete piece of **, never ever buy one.

Years ago I purchased the Dacor Double Oven over a Thermador because the Thermador had a ridiculously long pre-heat time. The Dacor has performed reasonably well as a oven particularly in convection-bake mode. But over time, components started failing and repair parts were hard to find, unavailable or ridiculously overpriced. I am an an engineer with DIY skills honed from years working with high tech food manufacturing equipment and controls including ovens. In recent years, I have needed to replace a relay board, the main control board, hinges two times, and most recently the hinge receptacles. I have also replaced an inner panel on a door assembly. Just think what such repairs would have cost for an average consumer. I understand the parts can fail, but Dacor has shown little regard for consumers in my opinion. They have done very little to maintain an inventory of repair parts. Basically their message is that the part is now obsolete and unavailable. Thats some answer when the price of a new double oven is multiple thousands. Recently, the hinges on my upper oven failed again. As they failed, their failure caused increased wear on the hinge receptacles. Soon the receptacles failed as well. I was able to find hinges at a ridiculously high price but the receptacles were unavailable anywhere. I contacted a several parts suppliers who told me that they had no idea when the parts would be available. Moreover at least two of the suppliers mentioned that they had a backlog of orders for the receptacles - one had a backlog of over thirty. Yikes!. At that point I contacted Dacor customer service and asked what could I do to get the part. Answer: The part is unavailable and we have no estimate on when it will be available. I tried to escalate my request and got nowhere. Finally after many hours of online searching, I found one set of the hinge receptacles at a price 4X last years price. Lastly as I replaced the receptacles today, I realized that the mounting screws only hold one portion of the U shaped mount. If the screws were longer, the receptacle would be less prone to twisting and wear. Be aware that Dacor was sold to Samsung a few years back. Based on my experience, I could never recommend Dacor. Caveat Emptor!

I own a complete Dacor Kitchen, with many appliances. They are the highlights of my Home. Great features: fast induction cooktop with an efficient silent hood, versatile refrigerator, reliable oven, and of course the always dependable dishwasher. This is My Dacor Kitchen!

This will be the third service call on my Dacor Built-in Refrigerator with the freezer making icicles and the fan making a loud noise. On top of that, I have two light bulbs in the freezer that went out from the ordeal. From my review of the complaints here on Consumer Affairs, I see Im not the only one with this issue. This is a yearly problem, and I hope Dacor would step up and resolve this for me since it truly is a poor design issue and no fault of mine.

Updated on 11/29/2018: Further to my recent review of my Dacor wall oven, I went to a high-end appliance store yesterday to research replacements for my microwave, oven, warming drawer installation (so, yay, I get to spend $13,000-plus to replace items I have had for only eight years). I cannot verify the accuracy of this, but the salesman explained the problem. For a period of time, Dacor and Viking used the same third-party supplier for their relay boards. Unbeknownst to the companies, the supplier substituted a part that was later discovered to be defective. Unfortunately, all replacement relay boards contain this part, so the problem will recur repeatedly, as many on this site have discovered.As bad as the cost of periodically replacing the board is, the unreliability of the oven is worse. As happened last time, mine works OK sometimes, burns everything other times, and struggles to get to the desired temperature other times. And because the behaviour is unpredictable, it cannot be reliably recreated when a repairman visits. I have had one email from Dacor and I responded with the information requested, then nothing. I suspect that they know they cannot fix the issue in a permanent way, so theyre just hoping all of us with this defective part will just go away. It looks like newer models that look like mine are still available, but I refuse to pay $5,000 on the off-chance that it has a better relay board. I am looking at Miele replacements.Original Review: I have had two Dacor wall oven, microwave, warming drawer installations. The first one was only a couple of years old when we moved, and Id had to replace the microwave, but I put it down to a power surge in the house after an outage. I have now had the same set in my new house since 2010. I have had to replace the microwave again, but not because of a power surge. It just stopped working. The oven has been a complete nightmare. The probe broke and although I had it repaired, it never worked properly, but the worse problem is that I am about to have to replace the electronic board for the SECOND TIME. When the problem occurs, the oven heats up to the setting but the element just stays on. I all but ruined an expensive cut of meat on the weekend – with company coming, no less – and just had to throw out a batch of muffins. I am considering tearing out the whole installation and getting another brand that doesnt destroy my food. It would probably be cheaper than having to fix the oven every year or two and replace the microwave periodically. These appliances are garbage.

We moved into our home in 2012 and have had nothing but problems with our Dacor refrigerator (Dacor Model EF48DCBSS). Our issue is the drain pan heater AGAIN. This problem is, water that collects in the drain pan freezes and eventually builds up to a point where the fan motor starts hitting it, sounding like a helicopter landing in your kitchen! Weve had this problem repaired THREE times by TWO DIFFERENT repair companies to the tune of $1000. Both repair technicians said it was a design flaw and this problem would continue to happen regardless of how many icing kits were replaced. So a $7000 refrigerator will cost us $1000 a year to keep running?!?!?! After much research, its apparent we are not alone with this problem. We also had a Dacor microwave just STOP working (model #DMT2420S). It was only 8 years old. Our Dacor oven range (model #ER48DSCH) has two ovens and only one side retains the heat. The main side gets to about 300 degrees and then the temperature starts dropping. Here is the breakdown of costs for our so called high end appliances. Dual Fuel Range - $10000, refrigerator - $7000 (annual repairs of $1000), microwave - $500 (had to purchase new microwave $600). PLEASE LEARN FROM OUR MISTAKE AND DO NOT PURCHASE DACOR APPLIANCES. We have a refrigerator/freezer that we bought from Sears SIXTEEN years ago for $500. Still works like a charm! And thank God we have it, because it has had to be our backup for our $7000 Dacor.

My Epicure dishwasher is being replaced after 4 years of use. The racks are rusted. It leaks. And the spray arms are broken in two. The dishes need to be completely washed before putting in dishwasher. Do not purchase Dacor dishwasher.

We remodeled our home and purchased Dacor appliances for our kitchen. Range, love it, Microwave, 30 Double oven and warming drawer (promotional give away). The ovens from the beginning do not function well. To warm up the ovens I have to wait 45-50 minutes and it buzzes. It is at temperature but then when I look at thermometer we are close to 75 degrees below. It recycles temperature every 75 degrees too. We had many repairs to the original unit to the point the repair person recommended that Dacor replace the unit. They did, another disaster. First they dropped the old unit while removing it chipping my granite, destroying my drawer panel and then left an absolute mess. The second unit has the same warm up issues, holding temperatures and oh wait, fans ran for hours after they were turned off. Broiling amazing. Baking and convection, a joke.The last repair person told me to open the oven and turn the cookies to have them cook evenly. And do the same when cooking with Convection. :/ I am currently looking for a reliable double oven that I can use and feel good about the food I serve (to be cooked). Dacor basically said that they cannot help me anymore because we went out of warranty last year and sent a repair person to basically say it is acceptable. Obviously for someone who does not cook, just sayin.

I purchased a Dacor Refrigerator about 4 years ago and have had nothing but constant problems with it over the years. Finally they agreed to send me a new refrigerator, and now after five months I am having a major problem with it, and have been trying for 3 hours to get a warranty authorization from them so I can have a repair man come out and stop a major leak that is now leaking into the condo below me. I am so disgusted with their products and their service that I really would never advise anyone purchasing a Dacor product. If I could I would buy another brand then be done with it, but this was a $9,000.00 refrigerator - CAN YOU IMAGINE THAT???

I have an older cooktop. Yes it is 15 years going strong but I have ran into a few issues where I know the repairs would be pricey but especially the parts. After talking to a few representatives, they truly want to help you. Nothing is free and I don’t expect it to be, but I am glad they they helped me get my cooktop back to functioning again. I hope someone finds this helpful before reading or writing bad reviews.

We purchased a Dacor gas range in 2005 for $2000. In a short time the plastic trim around the knobs cracked, and the glass in the oven door had not maintained its seal. I contacted Dacor several times and was told to take a picture and send it to them, then they could decide a course of action. The course of action was that I would pay for materials and labor. I decided not to do that, and eventually I will replace the range with another brand, never a Dacor!

This is a follow-up comment from my last post dated June 21st 2011. My local appliance company, where I purchased this oven, seems to have helped with their recent fix. I was able to bake a white cake, following the box directions, that was not burned on one side and raw on the other; it was okay. With fall arriving, I will be back in my kitchen and will be using my oven. I will keep you posted. I still would not recommend this oven to anyone, and will not purchase any future Dacor products.

We purchased our range (Dacor Dual Fuel Range RSD30) in about 1997 thinking we had a good investment. We have replaced the bezel 5 times (the area that encloses the control area). Today the door glass has cracked. Whooppee! Merry Christmas! Each time I called about the bezel, I was told that they had a design flaw. The last time we had to replace the bezel and also pay for installation ourselves. We decided if this happened again, we would get rid of it. Well, it will be sooner than later as the oven glass has cracked. Needless to say, we are not return customers.

I am writing to complain about our Dacor dual fuel stove that we purchased in 1998 when we built our house. Initially things went well, and I enjoyed baking in the oven and the convenience of the gas stove top when we had power issues. But then the honeymoon ended, and the problems started. After completing our first self clean cycle, we started getting the F1 code, and noticed cracks in the front on the stove. Our repair guy came out, took a look, and then informed me that Dacor had had numerous problems, and were not so good about living up to their warranty. He was right, Dacor felt in no way that they should help resolve our problem. With 4 kids, you cant just go without a stove, so we paid for the parts and repair. I figured it was just a one time thing, but I was wrong. We are now again looking at replacing the same part just 3 years later again with cracks and the F1 code. Dacor should be ashamed. Do the math. If they walk away from responsibility on all of these faulty products that average $5,000 a piece, shouldnt they have the money to pay for the fixes or maybe hire better engineers? They need to be held accountable for this mess. I need my oven back on!!!! And after the money we have paid for repairs, light bulbs, and parts...... the rest of the care should be free and on them.

After less than a year after installation the oven continues to operate poorly. Its been recalibrate twice and a new control board installed. Did I mention the board had burned components? It still does not operate properly. Its at least 25 degrees off. Everything takes way longer to cook than it should. Thanksgiving was 2 hours late. Christmas was the same. Entertaining during the holidays, embarrassing. Now Dacor wants pictures to prove to truly see how poorly the oven is operating. I thought I bought a quality product but I was wrong. This is just following suit with the Dacor refrigerator I purchased and was replace months later.

Dacor range - After I posted my comments on August 8th, I was contacted by Dacor customer service immediately and the new part was sent to me free of charge. I do have to pay the labor, but the part was what was expensive before. They did give me an explanation as to why this was happening - the hinges on the door wear out and the door doesnt shut properly so that heat escapes. Should this be happening with a stove that was this expensive? I dont think so, but I am happy with the customer service I received from Dacor this time.

Dacor Worst Oven Ever. Major kitchen remodel in 2005. Designer recommended Dacor for great styling and the fact that it was a 36 inch oven. Before the kitchen was even finished the control panel had to be replaced. Since 2005 our local repair shop has had to replace the circuit board 9 times. Same issue every time with not heating and board found every time to be burned out! Dacor replaced the first few boards free but we had to cover the labor. To date more than 5,000 in repairs. Dacor would not replace the oven and had terrible customer service. Its down for the 12th time and its headed to the junkyard this time. I cant see spending another dime on this lemon. Dont ever buy a Dacor!

Front bevel of my first rsd30 range purchased in California in 1999 cracked within nine months. Dacor said it was a defect in the design and would fix it for free. I sold the house in 2001 but the range was still not fixed. I moved to Nevada and bought a new rsd30 range and same thing happened within six months. It took a year to get it fixed at their expense. This bevel also cracked again for the second time in March 2011. Their response to this was to offer me a new bevel for $180 and I would have to pay for the installation. I declined the offer. The bevel is still cracked at this time. At the same time, I bought a PMOR30 over the range microwave and the front handle broke at least four times. And finally, the whole thing broke down and was not repairable. In Aug. 2008, I contacted Dacor and they agreed to replace it with a new DMT2420 over the counter microwave for half the price ($390). Last week, this one blew up on me. Sparks were coming out through the side and a big hole in the removable shield and burn damage to the wall of the unit. I do not believe this unit is repairable. I contacted Michael at Dacor. He apologized and said that theres nothing they can do about it as it is out of warranty but they will look into it. What I want at this point is my money back that I paid for ($390) and for them to pick up the unit and get it out of my house. I will never buy another Dacor product again.

The Dacor ‘duel fuel’ ranger was $5,500, We have propone, and Dacor’s set up is for natural gas, so all the pots and pans got lots of dark residual. I wrote and called them many times, to no avail. Terrible customer service. Then the F1 error keeps beeping, non-stop. What a piece of junk. Non-stop issues. No service whatsoever from the manufacturer.

We remodeled our kitchen in 2016. We chose Dacor 30” range. The gas oven has been a disaster. After less than a year, it wouldn’t heat. They replaced it, same problem. Replaced the igniter and valve, same problem. Now they will do nothing and say we’re on our own. Problems with hood and fridge too. Stay away from Dacor at all costs!

Epicure Range, wall oven, microwave and fridge - When remodeling our kitchen in 2010, an appliance salesperson gave us a good deal on the entire set. We spent $20k on the Dacor appliances. BIG MISTAKE! Do not ever buy anything Dacor. We have issues with every single one. Where do I start? The ovens have gone out three times now and I have had to replace the main panel, now it will not heat at all. The refrigerator 42 built-in is a big piece of crap! We have had it serviced 4-times for everything. The entire fridge freezes over due to a design flaw. The fan in the freezer completely ices over. The ice door broke. The crushed ice broke. The plastic door for the butter broke. The shelves broke.The microwave has had issues and has had to be fixed. The oven temps were wrong. Fixed those myself thanks to YouTube. When talking to the service guy he said that these are cheap appliances with the Dacor badge, so you have to spend big bucks to buy them and big bucks to repair! Do yourself a favor and if you are thinking of Dacor run! I contacted Dacor and they are even worse to deal with. They did not care that their appliances are very unreliable. Never received a return call, email, or even a letter.

Don’t purchase Dacor appliance - it’s been worst purchase experience ever and I am extremely disappointed. After six months since I purchased the Dacor built-in refrigerator, Dacor couldn’t even ship the proper installation parts and my refrigerator is still not working. Problems:1. Their high end $11K Dacor built-in refrigerator cannot even be installed. Wasted five months communicating with both Dacor and the retailer AppliancesConnection. After five months they were still able to ship the proper missing installation parts. Over the past five months, I talked to six different team members in Dacor customer support team, escalated to customer support lead and also talked to their regional technical manager, none of them is able to solve my problem and ship the right installation parts.a) Their process is extremely messy. Their customer support team had no idea about installation requirement of the refrigerator. And the request from their customer support team is declined by their internal Parts department again and again, only to find out installation parts should’ve shipped by the retailer. This is extremely confusing now and no one in the team seems to understand the right process.b) After Dacor acquired by Samsung, their manufacturing process is very messy and parts are extremely confusing. There’s one version of required installation parts in Dacor manual and one version of Samsung parts in the Parts guide, and no one in the team seems to understand the difference and how to map from one to another (they insist on sending me Samsung parts instead, claiming they’re compatible). I am now the expert myself to understand all their parts and able to identify many problems in their manual.2. As a high end brand, Dacor doesn’t seem to care about their customer at all. As a customer who did kitchen remodeling and had no refrigerator to use for five months, no one in the team seems to care about their brand or their customers. With this huge gap in the process, no one thinks about the problem from their customer’s perspective or shared empathy with me. Dacor as a brand is really bad and I am extremely disappointed in both their product and services.

We purchased our fridge for $9,249 in September of 2016. By the beginning February of 2019 the fridge stopped working completely, I called Dacor who sent out a technician to determine the problem. The technician said the compressor had failed and needed to be replaced. A week later we found out that Dacor no longer makes the particular compressor I need. I have now been living without a fridge for 3 weeks and Dacor doesn’t seem to care at all. We have 3 children and are currently living out of a cooler with ice. I call them and email them every day begging them for a resolution. They are a avoiding me. I believe they owe me a new fridge and they don’t want to do it. We saved long and hard for our expensive appliances and it’s absolutely heartbreaking to have this useless fridge stop working after 2 years, and Dacor seems to not care.

I contacted James ** at Dacor. His attitude was excellent and he resolved my problem (deteriorating dishwasher racks) beyond my expectations. He was compassionate and understanding every step of the way. James followed through on his promises in a swift and efficient manner. I would recommend Dacor and James ** to anyone. He is an asset to Dacor and should be recognized for his professionalism.

I am very, very pleased to report that I was contacted by Dacor a day after I posted my review which addressed a second failed relay board in 7 years. A really helpful Customer Service Representative called me (not emailed) to discuss the issue in great detail. Within a matter of days, a local repair service had received the new part from Dacor and scheduled an appointment with me to come out and replace the defective part. Dacor covered both the part and the labor. Im really sorry that the oven needed a second major repair but I will say that Im impressed with Dacors resolution of this issue!

I was and, I repeat, was a loyal Dacor customer. I gutted and rebuilt a kitchen 9 years ago and purchased a Dacor stovetop, oven and microwave. I remodeled my new house 5 years ago and again purchased Dacor stovetop, oven and microwave. Consumer reports provided favorable reviews of the appliances I purchased below.First red alert: The oven Model MORS130S and Microwave Model DCM 24S LED did not match. The microwave was green; oven was blue. The brochure was in black and white so there was no way of knowing that aesthetically they were a mismatch ... it was very sloppy(!) and very deceptive by Dacor. I mean when I waited weeks for my appliance order and the oven is already installed with a big fat ugly LED screen, what was I supposed to do, yank it out and start all over again? This was disappointing!Next, I was simmering chili on the stovetop (5 burner, gas) and, lo and behold, 18 flames started exiting through the turn knobs resulting in a meltdown. The gas was leaking through the tubes underneath the stovetop. I just happened to check the chili while I was gardening to watch the house almost burn down and btw, it was difficult to put out the flames because the natural gas was leaking under the unit. Seriously! I called customer service and they got hopping right out to fix the issue. This scared the heck out of me. It is negligent to have a product like that on the market.After about 13 months into the life of the Model MORS130S oven, the touch panel failed emitting a CO1 error message. I was told it was $140 to fix it and that the panel was defective, great quality there, Dacor. And the added joy to the CO1 error message is that the unit beeps intermittently all day and all night long unless the power to the oven is killed. Joy... now another issue - Model MORS130S oven LED lights are burning out. Seriously, what else will there be? Now its $175 for LED panel and another $100 to install by an authorized Dacor service man.So I called Dacor back again today because the LED light out was annoying me. They offered nothing. To be fair, my appliances are out of warranty but seriously, Dacor nearly burned my house down. They should be winning me back as a customer if they really cared about their customers and having long term repeat business. Never again, Dacor, never!