As an add-on to my original review, I had a a service call to address the LC error code. The service company reconnected my unit, turned it on, ran a couple tests, and declared there was no issue. We ran the dishwasher 1 cycle and it worked just fine. Tried to run it again later that day, and the LC code was back again. To resolve the issue, I worked with the company I bought my appliances through to replace the Dacor dishwasher with a Bosch. That happened today, so it is too early to tell say how the Bosch works, but it is more solidly built, has more capacity and the door fully opens with the panel installed.Dacor did reach out to me to try to resolve this issue, so kudos to their customer support, but the issues were just too many. And as I stated in my original review, love the Dacor range top, double oven and refrigerator.

We remodeled our kitchen because my wife is a chef. So we thought a full suite of Dacor products was just what she needed. What a mistake! Our $6000 36-inch dual-fuel range had problems from the start. We had to replace the control panel, heating element, convection fan, and door seal. Finally, the liner split and the range became unrepairable. We made the mistake of purchasing a simpler, gas-only range because Dacor offered a modest discount. This $7000 range lasted four months before a failure in the wiring harness made it unrepairable!! We bought a Miele replacement. We have had performance issues with our Dacor warming drawer and microwave. DO NOT BUY ANYTHING DACOR!!!

I have 2 single ovens side by side and have a cooktop and ventilation system - my experience with the cooktop and vent (2000) was so good that I did not hesitate to buy Dacor MorS130S ovens. They were installed in my new kitchen in September of 2012. I had my cooktop and ventilation system reinstalled. My daughter accidentally cleaned the oven without taking out the GlideRacks (which are hard to take out). We oiled them, etc., like the manual says if they are accidentally left in - they will not glide at all and now I am being told $300 each to replace excluding the cost of the service call. This is ridiculous. What kind of design is so poor that racks would get in this condition? I had Bosch ovens before and their warranty was wonderful and I, luckily, bought a Miele dishwasher which has a 10-year warranty. I would not buy Dacor again because of the warranty and because of this problem. I am beyond disappointed as I love my cooktop etc. I feel that Dacor should at least pay for part of these GlideRacks.

We purchased a Dacor dual fuel oven range in 2008 in conjunction with an extensive kitchen remodel. It was beautiful and expensive. It has had innumerable problems. 2008: One of the igniters broke requiring replacement. 2014: oven stopped working, required new relay board. June 2020: Relay board again broke, oven stopped working. December 2020: Oven stopped working, heating element broke. These were serious problems each resulting in 1-2 months without an oven as the parts had to be special ordered. We have not had an oven since December 2020 (it is now March 2021). We are waiting for a replacement part. In addition, minor problems included a broken indicator light and burner grating. Dacor customer service was only moderately helpful, referring us to local repair companies that had difficulty obtaining parts. Dacor has told us that this should last decades but we are seriously considering replacing it after 12 years because it is very unreliable. I would not recommend a Dacor based on our experience.

When the beverage center was initially installed 5 or so years ago, I went to put wine bottles in the wine drawers and surprisingly, the shelves are too shallow to properly hold some of the bottles especially tall Riesling bottles. I contacted Dacor to get some response to the poor design and got no response. Now the unit wont chill and I have just paid a repairman $162 to tell me it is not repairable because the unit has a leak in the refrigeration system and it is within a foamed in area of the system. So after only 5 years, I am replacing my wine fridge, not what I would have expected from a brand that touts itself as being high end. I am very dissatisfied with Dacor and certainly will not be purchasing anything of that brand again.

I emailed Dacor for information about how to get my range fixed and was amazed. My questions were answered complete with numbers for model and needed replacement parts along with contact information for local service folks. Amazingly good service. Bravo, Tori **! Give that woman a raise!

I own a complete Dacor Kitchen, with many appliances. They are the highlights of my Home. Great features: fast induction cooktop with an efficient silent hood, versatile refrigerator, reliable oven, and of course the always dependable dishwasher. This is My Dacor Kitchen!

Purchased Dacor Renaissance wall oven in July 2015, Model RNO130S. After less than a year and a half, the cooking temperature began to fail. For instance, set to bake at 425 degrees, the oven would appear to heat properly, but tried and true recipes would be pasty and uncooked at the expected time. I inserted an oven thermometer inside to test and found an erratic pattern of oven heating up properly to 425 but then sometimes dropping back to about 350 during cook time and refusing to ever reach 425 again. ABT repairman adjusted temperature calibration but refused to troubleshoot any further. Just ruined another dinner. Thanks Dacor and ABT for your unreliable product and poor service.

I completed a 7-month total remodel of our kitchen and family room, which were connected in November 2007. The kitchen remodel cost $18,000 for various Dacor appliances including the Millenia series of wall oven MOV130S; warming drawer MWDV30; and 42 island hood DHI42130. The remaining includes the huge 30 Epicure dishwasher ED30SCP, 36 cooktop EG366SCH, and beverage center EF24LBCSS. All have the beautiful copper accent package and make for highly attractive appliances. We constantly receive accolades for them. If only they werent absolute garbage functionally and reliability-wise. Others have remarked how the ignitors on the cooktop continually spark, even after the light off. After contacting Dacor and waiting 2 weeks for the repair, for which Dacor sent the wrong part and caused another 2-week delay, the repairman had to rip off the front accent lip of the cooktop to reach the base which significantly dented the front lip. The ignitor worked like a champ for 2 days, then click, click, click - constant ignitions. So I cleaned around the ignitor tip with 409, dried it and it worked flawlessly. Thanks Dacor for your own product ignorance and my now dented cooktop. It has worked well since and is a sound product, so far. If only my luck held out.Next, the wall oven. Very beautiful and my control panel has held out (fingers faithlessly crossed). The oven isnt calibrated though, so follow cooking directions at your own risk. This oven will burn your food if you set the temp and timer to the recommended settings. I have to take off 25-50 degrees and 5-10 minutes of requested cook time or I will smoke any meal. After 2 years of use, I decided to use the cleaning cycle - following the directions to the letter. Forty five minutes into the cycle and kaboo! The front window shattered. Dacor says $700+ for glass replacement; I say send me the part and Ill do it. I got the discounted part for $68; spent 3 hours cleaning and reassembling with care; and the window has held, but I havent tried the cleaning cycle since. Why roll the dice again?Ah, now my fave garbage Dacor appliance - the interminable dishwasher. Truly engineered by the diabolical. I just completed my fourth major repair after 5 years of use. First, the drain valve failed after a few months of use causing flood and was replaced under warranty. Then the door seal failed (more flooding) and was also repaired and replaced under warranty. The dishwasher stinks, by the way, as the unit cannot evaporate effectively during drying cycle due to ridiculously poor rear venting design. So I have to leave the door wide open for hours after use to facilitate drying and stench reduction. The control panel/circuit board has fried twice now in the last 3 years - it just starts erratically beeping and refuses to take input, even with a power reset. Both technicians stated the design and quality of the board is third world, which likely is exactly where Dacor outsourced the garbage.The island hood and warming drawer have worked well, and the beverage center has been reliable but maddeningly causes back left cans of soda to freeze and explode occasionally; even with the set temperature raised to now 45 degrees. Fun to clean up after coming home from a long trip. My expectations are so laughingly low now for these Dacor products that I dont bat an eye with the frozen soda muck this fridge occasionally produces. Customer service though has been helpful and thankfully, American. They have replaced both circuit boards for free well out of warranty. I have only appreciation and great sympathy for the customer service folks who Ive spoken with. I love my kitchen, but hate the appliances in it. Never again Dacor. Never again.

We remodeled our kitchen in the fall of 2009 and decided to purchase what we thought were higher end Dacor appliances (stove top, oven and microwave). Well, what a mistake that turned out to be. Considering the price we paid for the appliances, you would not expect problems from all 3. Perhaps a problem with 1 appliance, but problems with all 3 suggest a real quality problem. My first indication should have been when I called and asked how to change the green LED on the microwave to blue to match the nice blue LEDs on the oven mounted right below. I was told that someone else makes the microwave and Dacor just puts their name, and that I should just turn off the LED on the microwave. I dont know if that is true, but that is what I was told.Now when using the microwave/convection feature, the oven makes a noise (sounds like a fan motor) for the first 3-5 minutes then eventually quiets down. A daily reminder of the mistake we made purchasing Dacor. Then those nice blue LEDs on the oven started failing making it impossible to read the clock, timer or temp. Luckily, the oven still works; you just cannot read the LED any longer. This is a constant reminder of the mistake we made buying Dacor as we see the LED every time we walk into the kitchen.Finally, we have the solid surface electric cooktop. Although it works fine, the black paint on the metal trim around the stove top is wearing off. Now, we have some shiny metal and some black trim. This is just an annoyance and honestly, we probably would not have even complained about it. However, with the other problems we have had with Dacor, it just adds to our overall disappointment with Dacor. If I knew then what I know now, I would be a lot happier because I would have GE appliances and not these overpriced low quality Dacor appliances.

We purchased a Dacor built-in refrigerator in 2011. After just 5 years the warning beeper came on. We learned that the main control panel - built by Whirlpool - was defective. We then learned that Dacor did not have any replacement part for this model. Our only alternative was the purchase a new refrigerator. Amazing!! Dacor reluctantly gave us a partial credit for a new (KitchenAid) model. However at the end of the day we are out of pocket over $2000 because Dacor built and sold a defective refrigerator with no ability to fix the problem. Very unsatisfactory handling of this situation.

I purchased a Dacor double wall oven in May 2011 at a reduced price from a secondary market. Due to cosmetic defects, it wasnt sold by an authorized Dacor dealer. I bought it at what I thought was a fair price, considering the cosmetic defects. When our home was completed in November 2011, we installed the oven but found the oven would not heat up to the set temperature. I was told by the company I bought it from that it would be eligible to be covered under the manufacturers warranty. I called Dacor and was told that since I didnt buy it from an authorized dealer, they would not cover it under their warranty even though I had it under one year. Since I had to give Dacor the serial number when I called it in, they now have a permanent record to that end. I have had no oven because I cannot pay to have it repaired.

We moved into our home in July 2012 and have had nothing but problems from our Dacor refrigerator which was manufactured and installed in this home in 2007. The appliance repair company has been to our home approximately five times in the five weeks since we moved in. Initially, the problem was with a leak in the cooling system which took the technicians about 16 hours over three visits and $1,400 to sort out. Currently, we have been without a visit from the techs in two weeks (our longest stretch since moving in) and the refrigerator is leaking from the ice dispenser and making a motorized noise so loud. Initially, I thought a motorcycle had pulled into my kitchen. Needless to say, the technicians are on their way back.

I have an Dacor column fridge and after 18 mths (under warrant), its not cooling. Its been 3 weeks, 2 repair visits and Im still out of fridge. Repair person said this is a known issue. If this is the case, Dacor should be proactive and reaching out to consumers under warranty to get this fixed instead of waiting for complaints. Interior trim kit is not included in purchase price which is ridiculous for the price of this fridge. Would not recommend!

My wife and spend $12k on a new Dacor range/oven 15 years ago. The range works well, the LED lights on the gas knobs needed changed once in a while, the oven door wouldn’t close properly and the heat in the oven wasn’t distributed evenly. All that we could live with. Then the oven died. The repair technician ordered the part. Samsung don’t make it anymore. We are now left with no oven. So we have spent $800 a year on a Dacor range that now doesn’t work. Thanks Dacor… or Samsung?

We had our whole kitchen renovated and purchased Dacor appliances through Caplans Appliances. We purchased the appliances in the summer of 2019 and they were shipped shortly after. Since our kitchen was still under construction the appliances sat in our home. They were installed the second week of November. Two months ago, I woke up to a sucking noise from the dishwasher. The dishwasher had a code of LC. We removed the custom kick plate to realize that there was water damage. Dacor has been contacted on numerous occasions regarding this and the dishwasher continues to leak. We have had 5 service calls to house and the problem persists. The seal has been replaced twice in a 2 week period. The repair company HARGTA gives us a window and does not show up at that time causing me to sit around all day waiting for them and then some days having to cancel work. Dacor customer service continues to say the Regional Tech Manager will be the one to provide the resolution and we have not heard from them yet. The reviews on here clearly indicate that the dishwasher leaks. We are risking damaging our floors which were put in at the same of our renovation. Looking for a resolution ASAP. To those considering Dacor appliances do your research.

48 in. Range - Wish I had read reviews first would NEVER have purchased Dacor. Paid almost 11,000.00 for a range so many issues they replaced it. New range came with 7 defects. It has been over a month and nothing has been done about it. Everyone keeps passing the buck and I am sitting with an high end expensive product and no help from Dacor. I am being very patient but also very frustrated at this point.

Add me to the Dacor hate list. The $4300 oven installed in 2000 is now a whopping $6400. My motherboard #2 is broken and the glass on the door cracked which to me is a safety issue. This is a two adult, no kid household so figure. We use the oven about 7 times a year. My Dacor rangetop and hydraulic exhaust have both required service as well.

I wrote yesterday, perhaps a little too hastily that our motherboard was dead on our Dacor stove. The repairman came today and fixed it by removing it from the front of the stove and unplugging two plugs and plugging them back in. Everything works fine now and we are vastly relieved. The repairman commented that most people are very happy with their Dacor appliances and he doesnt repair them very often.Total relief. Also hope this doesnt happen again because though extremely simple to repair, it would become very tiresome to remove the motherboard and fiddle with the sophisticated circuitry if we had to do it ourselves. I wasnt watching real closely what the guy did and dont know if I could do it myself.

We did a complete kitchen remodel in 2007. I wanted top of the line appliances, and I liked the look of Dacor. I spent over $10,000 on a refrigerator, oversize dishwasher, microwave oven and a warming oven... (I know). Within 16 months, everything started to fall apart. Of course it was over the one year’s mark so there was no replacing of the units on the manufacturers part. I have since replaced the motherboard on the dishwasher twice... total of 3K in repairs! I cant replace the dishwasher because it was oversized and we built our cabinets around it and no other company sell an oversized dishwasher. I have replaced the microwave oven with another one that looks just like it because for some reason it fried. The refrigerator constantly rattles and my husband and I are at our wits end because of it. The only thing that hasnt fell apart yet is the warming oven. Probably because we dont use it. I wouldnt recommend it to anyone. Its a total waste of money. Next time Im buying Kenmore. My old Kenmore is sitting out in the garage being a good and faithful second fridge.

We chose DACOR (8-burner double oven top of the line ERD60S06CH/LP) in 2006, new construction because we disliked the signature blue interior of another luxury brand. Last October I detected a gas leak from one of the burners. The authorized repair company was contacted, and the entire unit - all 8 burners and both ovens were out of commission while we waited for the replacement part. Six weeks later the repair guy returned with the wrong part. We had to wait an additional month for the repair guy to return. Apparently, not important that people might want to cook and bake before the Holidays! After the new valve was replaced the oven light began to turn on when any of the gas valves on the defective side was turned on. I write this review 8 months into the problem. I can fix for $700 by ordering a new control panel. I wish I had read these reviews earlier. I overheard the tech say that there was electrical interference and that the wires need to be insulated to stop the oven light from turning on and off. I am so FED up with both the Dacor California head office not caring and the horrible authorized service company. I will take this unit apart myself and fix it. DACOR IS GARBAGE. Go with Sub-Zero, Miele and forget this Brand. DACOR: Dont Accept Crap Or Rubbish! Made in America? Shame on you. No problems with 4 Sub-Zero fridges, or 4 Miele dishwasher the same age.

We purchased a home with brand new Dacor appliances. Within 1 year, the relay board had to be replaced. One year later, the relay board has to be replaced again. Its $600 each time for parts and labor... The part alone costs $500. The company does not warranty the relay board. At this point, we should have purchased a new wall oven. They claim these are superior appliances. Our gas stove top works well, but the wall oven and refrigerator have been nothing but problematic. We will never purchase this brand again.

Front bevel of my first rsd30 range purchased in California in 1999 cracked within nine months. Dacor said it was a defect in the design and would fix it for free. I sold the house in 2001 but the range was still not fixed. I moved to Nevada and bought a new rsd30 range and same thing happened within six months. It took a year to get it fixed at their expense. This bevel also cracked again for the second time in March 2011. Their response to this was to offer me a new bevel for $180 and I would have to pay for the installation. I declined the offer. The bevel is still cracked at this time. At the same time, I bought a PMOR30 over the range microwave and the front handle broke at least four times. And finally, the whole thing broke down and was not repairable. In Aug. 2008, I contacted Dacor and they agreed to replace it with a new DMT2420 over the counter microwave for half the price ($390). Last week, this one blew up on me. Sparks were coming out through the side and a big hole in the removable shield and burn damage to the wall of the unit. I do not believe this unit is repairable. I contacted Michael at Dacor. He apologized and said that theres nothing they can do about it as it is out of warranty but they will look into it. What I want at this point is my money back that I paid for ($390) and for them to pick up the unit and get it out of my house. I will never buy another Dacor product again.

We purchased this high end Dacor range (Dacor Renaissance ER30G) new in 2011 from the Appliance Loft here in Cincinnati. It was dropped off and installed and would not operate right out of the box. A repair was made and everything worked (unless you count the indicator lights on the knobs, they all went out after approx 14 months). This past November the oven went dead. A1 appliance came out: Determined new control board needed, ordered and installed. Thanksgiving Day, oven dead. A1 comes back, reset the High Temp Fuse. Oven dead 4 days later, A1 returns with a new HTF. Dec 22, Oven dead. As soon as The holiday is over we will call another repair shop and start looking at replacing this unreliable piece of eye candy. Open comment to Dacors design engineers, quality control engineers and management. You should be totally ashamed about this product youve designed. You are supposed to represent the best in American design and quality and this falls below that of low end appliances out of China. See you in small claims court.

After purchasing what I thought would be ovens of a lifetime I could not be more disappointed, frustrated and angry at a company in my buying history! Since November of 2014 and longer I have been fighting for service or answers or at least honesty! The ovens have never worked properly, they do not keep temperature. The oven temperature drops 60 to 75 degrees while cooking over a couple hours. The control board was replaced. Still the ovens never worked. If you like to cook and cook for the bed and breakfast, which is why you bought an oven like this, you will have your ovens on for a couples hours preparing any multi-dish meal! I was treated rudely on the phone during routine troubleshooting and was never allowed to speak to a manager. Dacor for months or so later is buying back my ovens minus a restocking fee, on ovens that dont work, $1200!

I purchased the Dacor panel ready refrigerator and freezer column 15 months ago. The refrigerator stopped cooling -- in 15 months! These were 8k each!!! It had now been over 2 months without a working refrigerator and no end in sight. I will never ever purchase one of their products again! They replaced the compressor and 3 days later it stopped cooling again. What a joke! DO NOT BUY DACOR!

Purchased Dacor Induction Range w Convection Oven RR30NIS-C in October 2013 and LOVE this range. Accidentally broke the glass on the induction cooktop with falling object mid-March 2020. Only the glass is broken, and all other electronics, induction burners, oven, etc are functioning fine. Called Dacor support to acquire part number for a glass top for repair - obtained part number #701751 superseded by #702285, BUT was informed that the part had been discontinued and is no longer being manufactured or kept in stock. No other advice was given other than to discard the entire $6000 range. Multiple phone calls with service.I asked for a listing of third party part distributors and was referred to four distributors on the Dacor public website and given no other info. I called all web-based third-party distributors I could find in USA and Canada to see if anyone had the part in stock, with no luck. I contacted two technicians to see if they would be able to obtain the part through their channels, with no luck. I am an engineer, so I spent some time pouring over technical manuals trying to find a solution to replace the entire induction range cooktop assembly (top part of the range) with a later model, and although its possible, Dacor would not provide the ability to purchase an RNR30NI range cooktop assembly that could be fit into the existing housing on top of the range. The convection oven is completely fine, and I cannot believe that Dacor has given me no other option but to pitch a six-year-old $6000 range because they stopped manufacturing one fragile part made of glass. I would imagine that many consumers may be in the same position as I, as these cooktops are breakable, and accidents happen. I have reached out to Dacor support desk numerous times without resolution, and I am at my wits end with a $6000 boat anchor in my kitchen. What a waste of money! Poorly done Dacor!I would like Dacor to provide me with some sort of solution whether it be the part required to fix my induction cooktop, or a replacement Induction Range with convection oven, or reimbursement of the purchase price so I can obtain a replacement on my own. If I am not able to find a solution to repair my range, I will never buy from Dacor again! Dacor will discontinue easily broken parts without warning! You may spend thousands of dollars and not be able to repair your appliance after warranty expires!

I purchased this upgrade to my kitchen renovation. The stainless steel stove has a great look, but that is all it has. This is my third repair (with much difficulty). The same problem - the bake ignitor goes bad and sends gas smells throughout the kitchen. On Christmas day, after preheating the oven, I opened the oven door and the inside was one large flame. The heat was intense and my right arm got hot from the heat. I immediately closed the oven and cancelled the bake setting. When I called Dacor the following morning, I thought I was talking with a robot. No emotions, no sense of caring. They must be programmed. I got no satisfaction. I said, Do you understand? My stove went on fire and on Christmas day. My family was not sure if they should leave my house. I am extremely disappointed with Dacor.

I am having issues with my Dacor oven and have tried to contact customer service since Monday 01/04/16. I was on hold for 27 mins and finally left my number for a callback. I have called every day and leave my number for a callback, no response. Today Thursday I sent a message and the response was that someone will call within 2 days. Great customer service. Buyer beware.

We got a Dacor oven and microwave wall mounted Unit 7 model DMT 2420S when we remodeled our kitchen. I have had problems with the microwave with sparking on and off. I have stopped using it as I am worried about a fire.

We bought this oven and had it installed a month ago. Id love to love it, but unfortunately I dont even like it. Immediately after installation I noticed the touchpad for the bottom oven didnt work. I called Dacor and spent quite a bit of time while someone did the standard is the power on run through. I was told someone would have to call me back in the morning, at 9 am. The next day at 10 am having not heard a word, I called back. I was given the option to be called back (you wont lose your place, and our first rep...) Great! Nope. Four hours later still nothing. I called back again. Someone answered quickly and after a short call arranged for a service person to come out in a few days.Fast forward a few days and the serviceman arrives. Hes clearly never seen this kind of oven. He calls Dacor and talks to their troubleshooting department. They decide the motherboard is bad and reorder. Well, its been 10 days. *crickets*. There is no sense of urgency... In fact nobody even seems to care that my $7500.00 oven doesnt work and the microwave literally cant even pop popcorn. I would expect the company to rush delivery of the part. If need be replace the whole oven and figure out what is wrong with the motherboard on your own time. What I didnt expect is for literally everyone involved in the process of choosing and buying the appliance to not be able to find a solution. I give my new oven 1 star out of 10, because it looks nice. Id rather have an oven that doesnt have a smart feature and actually works. FAIL Dacor.

My Dacor Double oven is less than 5 years old. Lately, the broil function has stopped working well on both ovens. I contacted the ONLY authorized Dacor repair center - Home Appliance Repair GTA (HARGTA) and told them my broiler wasnt working well. Their repair technician came to my house, took both double oven doors off in order to give me the assessment – that my upper broil function was not working well. In fact, both upper and lower do not work well but thats a side issue. In the process, the technician broke or did not properly reinstall my double oven door. I called and he returned and again, removed BOTH oven doors. Now, my upper door is working well but my lower door has no hinge and falls hard and heavy. This is extremely dangerous. I have left multiple messages with HARGTA and they are not getting back to me. Ive even contacted DACOR which is only in the US and they havent gotten back to me either. I purchased a Dacor oven to get a quality appliance and excellent after care service. It appears that both the appliance and the aftercare service do not live up to their reputations. P.S. The quote to repair 1 broiler is $750 after less than 5 years of use. That will equal 1/4 of the oven cost in less than 5 years.

We bought a 36 inch Dacor range with oven last year, around September, when we moved in to our new house. We tried to turn the oven on Thanksgiving day for 10 people, but it would not work. We called for service, and they replaced the circuit board. The repairman turned the oven on, and it worked fine. We never used the oven, just the burners on top, because we have a second smaller oven, we like to use for every day cooking. Then came Christmas day, and we were having 30 people over, so we went to turn on the Dacor oven, but to our horror, it did not work again. We have owned this oven for a little over a year, and have tried to use it only twice. In that time, both on holidays, with a lot of people to feed. This time, when I called for service, they told me I will be charged $198, because when they tried to get Dacor to drop that charge, they said no. We are very disappointed in Dacor for not caring more about the customer.

I have had nothing but trouble with a wall oven I bought in 2010. Basically just bad electronics. I finally replaced the oven in 2014 and had to get another Dacor to fit the opening. The new unit still does not heat evenly and is consistently off by about 50 degrees. Customer service is not helpful at all. Local repair shops cant really fix issues. Terrible company. Cant figure out how they stay in business.

Epicure Range, wall oven, microwave and fridge - When remodeling our kitchen in 2010, an appliance salesperson gave us a good deal on the entire set. We spent $20k on the Dacor appliances. BIG MISTAKE! Do not ever buy anything Dacor. We have issues with every single one. Where do I start? The ovens have gone out three times now and I have had to replace the main panel, now it will not heat at all. The refrigerator 42 built-in is a big piece of crap! We have had it serviced 4-times for everything. The entire fridge freezes over due to a design flaw. The fan in the freezer completely ices over. The ice door broke. The crushed ice broke. The plastic door for the butter broke. The shelves broke.The microwave has had issues and has had to be fixed. The oven temps were wrong. Fixed those myself thanks to YouTube. When talking to the service guy he said that these are cheap appliances with the Dacor badge, so you have to spend big bucks to buy them and big bucks to repair! Do yourself a favor and if you are thinking of Dacor run! I contacted Dacor and they are even worse to deal with. They did not care that their appliances are very unreliable. Never received a return call, email, or even a letter.

In 2013 we remodel our kitchen. I need a 30" stove and Dacor seem the right fit. I had problem with the igniter burning on that stove and some metal warp as well. They replaced the stove in 2015. I smell gas every time I turn oven on. Last Thanksgiving 2019 the stove stop working. I was told the igniter had burned out and had it replaced. I had repairman come twice because of smell and end January 2020 the stove stop working again. The repairman told me that a jet burner assembly was never installed this is why I smell gas after it is turn on. ** They said they will order the part. It's back order So I contact Dacor. First they told me it's back order then give me a supplier. If it was never installed in the unit shouldn't Dacor take care of it and soon.

The oven I purchased is the Dacor double oven, model number - ECD230SCH, I purchased extended warranty on the ovens. This was purchased when I bought the ovens. I have renewed this and still have a warranty for 2 more years. I cannot get anyone to do the repair on this oven. My location is at the Sardis Lake. I cannot get anyone out to service. I do not know if you have any thing to do with this. I have had an oven out since June 2013. Please help, Dacor should have service reps in this area. I am in Sardis Ms.

I am writing to complain about our Dacor dual fuel stove that we purchased in 1998 when we built our house. Initially things went well, and I enjoyed baking in the oven and the convenience of the gas stove top when we had power issues. But then the honeymoon ended, and the problems started. After completing our first self clean cycle, we started getting the F1 code, and noticed cracks in the front on the stove. Our repair guy came out, took a look, and then informed me that Dacor had had numerous problems, and were not so good about living up to their warranty. He was right, Dacor felt in no way that they should help resolve our problem. With 4 kids, you cant just go without a stove, so we paid for the parts and repair. I figured it was just a one time thing, but I was wrong. We are now again looking at replacing the same part just 3 years later again with cracks and the F1 code. Dacor should be ashamed. Do the math. If they walk away from responsibility on all of these faulty products that average $5,000 a piece, shouldnt they have the money to pay for the fixes or maybe hire better engineers? They need to be held accountable for this mess. I need my oven back on!!!! And after the money we have paid for repairs, light bulbs, and parts...... the rest of the care should be free and on them.

I bought a Dacor dual-fuel range in 2002 for my new house. Within 18 months, the control panel on the front had shorted, causing the stove to emit a continuous beeping. I got this repaired, and was advised that I should not use liquid cleaners on the stove! Two years later, the same thing happened again. Finally, about 4 years ago, another fault developed in the 3rd control panel, the circuit controlling the oven lights will not respond to touch, and the oven lights switch on and off continuously. Not prepared to pay for yet another control panel replacement, I switched off the power to the stove at the main fuse box. I have continued to use the gas cooktop only, lighting it with an ignition wand. The Dacor stove is only part-functional due to what is obviously a severe design fault in the front touch control panel, which causes the panel to short. I switch on the power to the unit twice a year to use the oven at Thanksgiving and Christmas for large roasts. This stove was a very expensive mistake. Luckily, I have a second (Wolf) oven in my kitchen, which I use instead for everyday cooking.

I remodeled a kitchen in a high end house and so wanted nice appliances. I had KitchenAid (which Id had a lot of issues with) for about 16 years. (Since I built the house - the fridge was rebuilt 3 times.) While looking for which appliances to use we were at an open house and a chef was cooking and giving a talk on the Dacor ovens in it. So... I reviewed a lot, liked what I read, and chose Dacor. I love them, the cook quality, the features, all of it. BUT my double oven had issues from the start. An annoyance at first with the built in Android but I didnt complain a lot. Move forward 1.5 years and the Android tablet built into it would freeze and not restart without throwing a jumper on fuse box. I called Dacor and they gave me a number of options, disable the Android because of a known issue and get $500 back, or - return the oven for full credit and theyd pay to have it removed (1.5 years later... cmon thats pretty awesome), or - pay $500 and move to the newest higher end model with steam cooking. Wow, talk about stand by your product! Ive never seen this before with an appliance manufacturer/vendor. Certainly wasnt my experience with KitchenAid. Anyway Im an advocate even though I had a problem and thought they deserved credit here.

I bought a 30 Dacor Double Oven (EO230SCH), 36 cooktop, warming drawer and matching convection microwave. Well over $10k. The microwave has been replaced as it died early within the first year while cooking popcorn - nearly started a fire in the kitchen... However the cooktop igniter died at 4 years and now the wall oven is on its third control board in years 3, 4 and 5. Nothing is under warranty and they want nothing to do with me now. The replacement oven controls cost ~$400 each plus installation. So after all this expense, I have invested $1,200 more in replacement parts and the cooktop needs an aim & flame to light. Total crap. Im going to replace all of this and will never go back to Dacor. I took the time to write this so that others will not waste their time with what I have to assume is the worst quality in the industry. Please dont waste your money.

First six month, dishwasher rusted on the inside. Dacor gave us a less expensive in its place. First year, microwave was repaired five times. Microwave has a piece of wood to hold the door in place. Wall Oven, the broiler never work. Present, range oven does not work at all. We have a repairman that is trying to get parts. Present, refrigeration control panel does not work, need repair. These appliances were to be a our luxury kitchen, but turn into a nightmare. Do not buy this appliance, you are wasting your money.

I, too, purchased a 30 Heritage gas range in Nov 2018. The first time I ran the cleaning cycle (2 weeks ago), the oven heating went out. After time consuming attempts to reach the warranty dept, finally got a call back. Sent the required information and was told the warranty servicer would contact me within 48 hours. After not receiving such call, I reached out via email again to Dacor and was told to contact the servicer directly. Well, I just did that, and was told they refuse to service me because DACOR IS NOT PAYING THEM! How is that for a luxury appliance company making millions off of its customers and not paying its service companies? A very clear breach of contract since my warranty is active until November 2021. I have never in my life had such an experience, with the LG, KitchenAid ranges I have owned. Never even have needed one ounce of service in their life. So now I await a response from posts on Dacor FB page and voicemail I left, hoping for service. What a colossal waste of money. Buyer beware!

Liked the look of Dacor oven and fit in with remodel. Relay board replaced year after warranty - $600. Then after 8 years of light use (have Thermador home pro stove), another circuit board failed, part no longer manufactured. Oven now worthless and headed for landfill. Outrageous! Large national appliance retailer says Dacor not reliable. Daughter had major problems with Dacor fridge. Have purchased Kitchenaid replacement on recommendation of same retailer. Built to not last...shame on you, Dacor.

When our installer removed the packing material, he saw that the oven glass was shattered. Dacor said they would fix it, but wouldnt tell me how. I had to call the local repair shop to see what parts were being shipped. Only the glass! Not even the whole door. The idea that they would take apart and reassemble a brand new oven and consider that acceptable service makes me angry. This is supposed to be a high end company. I responded that this was unacceptable since the oven had obviously been dropped (shatter pattern spreads from the lower right corner of the glass) and might be a safety hazard. No response yet. Ill update this if/when I get a response.

Dacor EO227SCH - double wall oven. Installed all Dacor appliances when we did a kitchen renovation in 2008. Stove top, Micro Wave and Warming Drawer each have been excellent. Ovens have been a nightmare. Dacor would not honor warranty 7 days after it expired. Had no less than a dozen service calls in first 3 years. Ovens conveniently have problems around holidays. Example: lower oven quit working two days before this Thanksgiving - last week! Paid a high price to get Dacor and have paid thousands and spent countless hours on service calls since. Am totally dissatisfied with Dacor products and the companys refusal to stand behind its product. I tell everyone who is contemplating Dacor not to. Did it today with a couple who signed a contract for a $1M home in N Atlanta. Builder specified Dacor and I strongly advised against it. Homebuilder is now looking at other options.

I have a Dacor 27 inch wall (model EOR) oven which I bought 2 years ago, along with a micro and a warming drawer. Since then, the control panel has been replaced twice. Both times because, after using the timer mode, the beeper would come on at all hours of the day and night. In both instances, I had to cut the power to the oven until the replacement part arrived. I am presently waiting for the third panel to arrive. Today I needed to bake something, so I turned the power to the oven back on. Now it will only function at 350 degrees and only in the bake mode. No other numbers can be put in and nothing happens when I select convection. So far Dacor has absorbed the cost of the parts and repairs, but that does not mitigate the hassle of having to wait upwards of 2 months for a part each time this happens.

I just had an appliance repair company come out to let me know what is wrong with my Dacor Stove door, since it wont close. He said the hinges are needing to be replaced. He said that he replaces these hinges on Dacor stoves ALL THE TIME and that the company really needs to file a recall on these hinges and/or reimburse consumers who have these installed. He said these should not go bad like they do. That this is poor manufacturing on Dacors part and they are not being held accountable. I agree 100%. It is going to cost me with labor and parts almost $ 400.00 to replace these hinges that should not go bad with the age of the stove. Thanks.

Thank you for your attention. Since my post, a resolution has been reached and Dacor will be replacing my range with a new one. That is much more representative of the pride and reputation of Dacor. The executives were very responsive. Perhaps front line agents are not empowered to make these decisions, however, in my case, the escalation brought the matter into the right hands. Happy with the direction towards the final outcome, not the 4-month process that discounted the reputation and my perception.

I rarely write reviews but when I found your site, I decided it was time to vent. I bought a 36 dual fuel, convection Epicure range in 1999. It was not a cheap oven and I was excited at the possibilities of having a 16,000 BTU broiler and large oven cavity to work with. Lets just say that excitement quickly wore off. Almost immediately after the range went out of warranty, the ignitors went bad and we also had to replace the control panel ($400 in repairs was a lot back then). After that, we continued to have ignitor problems and replaced them again. Finally, I just stopped doing it and lit them with my aim and flame. I never allow my children to cook on the stove because I am afraid they will be burned. Most recently, my broiler element, relay board and again more ignitor problems ($1,200 in repairs). Not to mention, the repairman had a terrible time trying to access all the areas and was at my house for 4 hours trying to do so. When the initial problems happened, I emailed, phoned, left message, etc. to no avail with customer service (I use that term loosely). This company is the worst. I have told everyone I know never to buy a Dacor anything. Next time, Ill buy a Wolf.

We had our range oven for less than a year and the front electric panel cracked, there is no stress to this area. I called the company and they admitted the entire panel was defaulty and had a recall. They did replace it. Within 5 months the new one cracked in the same place. This time they stated the unit was out of warranty. I told them the same type of recalled panel was installed. They said I could buy a new one. Ha! Since then many more cracks. I will never buy anything made with the Decor brand nor do I recommend them! Happy shopping.

I have been very disappointed in the reliability of our Dacor refrigerator, model EF42BDCBSS, purchased in 2007. The first circuit board went out in 2008 within 6 months of the initial purchase. A replacement part could not be located. It was still under warranty so they replaced the whole unit. In 2010, we had to have another repair to regulate the temperature of the freezer. Last week (October 2012), the circuit board went out again! Even though the unit itself is less than five years old, it is no longer under warranty. Dacor goes by the original installation date. I contacted Dacor and spoke with LS who basically stated that all they could offer was a discount on the part. This repair is costing us over $650, not including the loss of food. We paid to have the part second day. When we called back the next day to get a tracking number for the shipment of the part, we were told by another representative that the part had not shipped because it was out of stock in the default warehouse. He was able to locate it in another warehouse and get it shipped the same day. I called LS back and she stated that she never promised when it would ship, but when it did, it would go second day. I would not expect this type of repair cost and attitude on a refrigerator that was over $9,000 when new. Now, I am concerned with the liability of our range and microwave, which are of the same Dacor brand. The main reason I took the time to write this email is to make retailers aware of the situation and ask that you seriously look at the reputation of the Dacor appliance line and decide if you really want to promote this product to your customers. Dacor could care less about their customers and/or reputation.

The glass plate in the bottom of the oven has been a disaster from day one. Anything that drops on it leaves a white mark that is impossible to remove. It finally became so discolored that I had to have it replaced; over$100 for glass and factory-trained repairman charged $285 to install, a ten-minute job. I wish someone had told me of the problems before I spent over $5,000 on a range which should be useable, not just pretty to look at which also doesnt happen when the oven is all stained. Burners are tinny and dont begin to compare with the Thermador I have in my other home. I will never purchase another Dacor product.

I have an older cooktop. Yes it is 15 years going strong but I have ran into a few issues where I know the repairs would be pricey but especially the parts. After talking to a few representatives, they truly want to help you. Nothing is free and I don’t expect it to be, but I am glad they they helped me get my cooktop back to functioning again. I hope someone finds this helpful before reading or writing bad reviews.

I have been getting the run around from Dacor regarding a part that I paid $700 to fix an interior light that comes on and off like a strobe light. After the local service company installed the part, recommended as the fix by Dacor, the issue returned. I contacted the technician again and that is when the run around started by Dacor. I was told to contact the customer service line and tell my story which I did, only to be told that the Range is too old and they dont stand behind the warranty nor service anymore. They said beyond 5 years they dont do anything for the customer.I paid $8000 for this range back in 2005 and it has worked just great until this recent issue. If I had known that there was no service nor any parts for the fix I would have just dismantled the interior light. But why did they recommend the part I did purchase to begin with? Are they just trying to increase revenues by advising customers to buy parts that wont work? DO NOT BUY DACOR PRODUCTS UNLESS YOU WANT TO BE ON THE HOOK FOR REPAIRS AFTER ONLY 5 YEARS! This company has rude customer service agents and they do not stand behind their name!

In 2001, I bought a Dacor dual range stove. I paid over $2000. My problem is that there is a defect in the product; when you use the self-cleaning, the outside of the stove cracks up. Dacor has replaced this three times and each time it cracks again. I spoke with them about a year ago and because I didnt continue the warranty, they wouldnt replace it. I carry a home warranty.My stove looks like it came from the junkyard. I understand them not repairing a physical problem with the stove but the outside is crumbling because of a defect in their product. If you dont clean the oven, then you get an error and the only way to get it off is to clean but all that dose causes the outside to crack up more. It pains me to think of buying a new range when I thought I had done my homework, when I choose Dacor. I hope this isnt too late, but it pains me to think after another cleaning I may be forced to buy another stove.

Like many of you on this site, when we remodeled our kitchen in 2000, I researched and decided to shell out the extra money for the highly recommended and higher priced Dacor everything. We got a double oven, glass 30 cooktop and an exhaust fan. 12+ years later, I wish I had bought GE! My ovens have had so many problems I cant even count. Basically, the temperature doesnt hold correctly. I have used oven thermometers and my husbands fancy gauge to check temp. I had a whole transformer and control panel changed out in hopes that it would correct the problem, but it didnt. I think it has something to do with the self-cleaning. I think it gets so hot that it fries the controller. I never use the broiler so its not like I left the door open and wasnt supposed to. This afternoon I set the oven to preheat to 350. I set my little cakes inside that I was making with my grandson. About 5 minutes later, it smelled like something was burning so I checked the little cakes. They were already charring on top and then I noticed that the top element was fiery red, basically on broil! What the heck?! This is ridiculous! Im not going to spend another $500 for another repair! I am waiting to see what the repairman says.On another note, my stovetop cracked twice! The last time, Dacor was nice enough to sell one to me at cost and my husband was able to install it. It didnt match the old one and I was told by Dacor that they dont make them anymore and that is made by a third party supplier now. The old one had a textured finish and this one is just very shiny and scratches so easily! I hate it. We also had a retractable exhaust fan put in because the stovetop is in an island. Every time I turn it on, my basement smells like whatever is cooking. Now the buttons dont work anymore. That is unless I jab them so hard with a sharp object that it finally makes enough contact to work! This is another part that we got at cost that my husband had to crawl around and repair that still doesnt work.So, all three Dacor appliances we bought have turned out to be very disappointing purchases. Dacor should stand behind their products better, offer longer warranties or better yet, build better products! I would never recommend these products to anyone!

We installed 2 Dacor wall ovens, a 5-burner cooktop, and a downdraft fan in 2000. The convection ovens bake perfectly and have performed without fail. After 7 to 8 years of daily use, we did have to replace the door hinge on the oven I use most often. We are in a rural area so the repairs are accomplished through Sears. The replacement parts arrived in a timely manner and the oven has worked perfectly since. The cooktop is easy to clean and the heat is even. The downdraft fan is effective and easy to clean. I would be confident to recommend Dacor products.

We purchased a Dacor Epicure dual fuel range when we built our house 7 years ago. It was the most expensive appliance we bought and we wish we hadnt. We have had no problems with the stove top, but the oven, specifically the broiler unit has been a consistent problem. We rarely use the broiler and use the oven perhaps 2 or 3 times a month. Yet, the igniter had to be replaced in March of 2008 and again, in June of 2010. In January of 2011, the broil gas valve was changed and now in September, the broiler is again not working. I cant see pouring any more money into this appliance and will sell as soon as I find a buyer willing to take a chance on it. We have been greatly disappointed in this product.

Very pleased to say Dacor replaced our oven with a new one! I havent thoroughly tested it all out yet, as it was replaced the day before we left for a trip. But so far the top oven seems to be working properly. Need to use the bottom oven yet to check it is working properly.

We built a new home in 2004. All appliances were Dacor. Since then, the oven has had to be repaired 4 times; the microwave had to be replaced; the cooktop has had two repairs and now will not light automatically; and the patio barbeque completely burned up and some of the parts melted. I did report that to the company and to the US Product Safety Commission. We have not abused any of these appliances and have followed the manufacturer recommendations all of the time. Dacor charges top dollar for their appliances, but they are not as good as cheaper brands. If you try to contact Dacor, they have a well-so-what attitude.

We bought our house in 2010 and our Dacor stove was supposedly newer. When I went to clean it, I found loose screws in the bottom. Apparently, the convection element is loosing its screws and washers. Ive had this appliance fixed once already when the cooktop kept clicking. The black plastic around the controls cracked mysteriously. It takes 3 hours longer to cook a turkey than it should. This is a strange stove, which supposedly cost a lot. I wonder if a convection part missing two screws should be used?

We purchased our home brand new in August 2006. The house was built and the appliances installed (but never used) in 2003. One of the things that sold us on the house was the kitchen being comprised of all high-end Dacor appliances (double convection oven, cooktop, dishwasher, and built-in microwave). Our excitement quickly turned to frustration. The first problems began with the dishwasher, which after several attempts at repair (circuit board) was begrudgingly replaced by Dacor, with “begrudgingly” being the key word. I have always found Dacor customer service to be rude and dismissive - with the only way that I ever received a satisfactory outcome, being via threats of contacting the BBB and Missouri Attorney General.About a year after receiving the replacement dishwasher, the internal racks began rusting badly. Once again, I called customer service who originally wanted to sell me new racks at a discount. Only after another persistent round of explaining that high-end dishwasher racks should be made from a material that doesnt rust, complaining and threatening, did I receive new racks free of charge. I was also informed that they had changed rack manufacturers and that would eliminate the rusting problem. Wrong. It has now been another couple of years, and the new racks are rusted worse than the previous ones. That is just the dishwasher.Our Dacor microwave display began slowly losing its LED display about 2 years ago. Lately, the microwave interior lining is beginning to disintegrate and rust through. One of the burners on our gas cooktop makes a constant popping noise when lit. The top half of our double convection oven no longer heats beyond 250 degrees. I realize that our appliances are now significantly beyond their warranty period, so I am no longer even attempting a resolution through Dacor. I will most likely ride these appliances into their graves and replace them with another brand. I am writing this mainly to alert others about my experiences with what I believe to be Dacors total lack of quality at a premium price. In my opinion, Dacor is all style and no substance.

We just purchased our home in March of this year. The previous homeowner purchased a Dacor oven; it is electric & propane. She purchased the appliance after a complete home renovation in 2008. They lived in the home. After 1 year, they moved out and had it on the market. We purchased the home in 2012. As soon as we moved in, we noticed the oven was not working. We called an appliance repairman - $564.00 service call and part for a new relay switch. It was great; the oven worked. Not even a day later, an F1 error. We called them back out thinking they must have done something incorrectly. They then said we needed a new control panel. We did not have an additional $400.00. We just moved, so he said you could still use the oven. We did. We would use it and flip the breaker off so we did not have to hear the annoying beeping sound. Then I came home and bam - no display, no oven. We called a different Dacor certified appliance guy thinking the first company was just taking us for a ride and it was their fault. $572.00 later, we got a new control panel, but guess what, the technician did not even make it to his truck before beep, beep, F1. He came back in and then said we needed to replace the display screen - an additional $217.00 with no labor charge. We told the man to shove it. I had every plan of taking the oven to our back tank and using it for target practice. But in good business practice, since this company already invested $572.00, we could not ask them to eat the money, so we allowed a third fix of the oven. While the technician was here, the oven made a horrible loud sound and shot out flames. He insisted maybe it was due to it sitting for a week without use. He left. I never noticed this flame before when the oven worked despite the F1 beeping. Now it’s hit and miss. Some days it will shoot out a flame once until it reaches 200+ degrees and then you can hear the fan kick in. Some days, twice, I have had it happen 3 times. If my children were to open the door during this event, I am sure they would be seriously burned. At first I was thinking maybe it is normal for this oven to shoot out flames during preheat mode since after $1300.00 repairs maybe it is just not functioning correctly. But if it were a normal function of the product, to me it would do it every time consistently and not three times, or two times on some occasions. I hate to admit this but I am almost fearful of using my oven. I currently have a pie to put in for dinner and I’m thinking its 3:09 pm; I could set the oven to preheat while I run to get my kids from school so if it decides to blow up, I am not home and that is pretty sad. The last repairman we had come out said in his personal opinion, he wouldn’t have repaired the oven, because they are known for issues, and he would have gone to Lowes and spent $300.00 on any off brand stove first. We have considered that, but this stove is extra-wide and the cabinetry is built around it. So for us to purchase an oven to slide right back in it would be another $1300.00-$2000.00. We have issues with the burners not always wanting to light. I almost caught on fire lighting one because it shot out flames when it decided to finally ignite. Sometimes it just clicks. Currently, I am down to two burners when just two days ago all six were working just fine. Over Thanksgiving, it took no kidding 1-hour to cook brown and serve rolls because the oven did not reach the set temperature. We stuck my husband’s bbq thermometer to see. It was 256 degrees, not the desired 350 degrees. Does this stove have warranty? We have no clue as the previous homeowner purchased the stove. She claims to have spent $5,000.00 on this stove or more during their purchase. We do not have warranty on our home so for each repair, it is out of pocket for us, and currently we really are thinking any knock off brand at Lowes would be a better product than a Dacor oven and less of a safety hazard for our family.

We have 3 Dacor appliances that we purchased new when we remodeled our kitchen a few years ago. Our cooktop’s igniter continually clicks even when it is not in the light position. This only happens on the front 2 burners (the back 3 are fine). We have cleaned the unit and cleaned the igniters over and over. We have had 2 authorized Dacor service companies and another company look at our unit. Two said no fix exists; the other replaced a part after talking to Dacor and that did not fix it. When I called Dacor, they noted to get another service company and call them when they are here. I am concerned that this again will not work and I will have to pay another service fee.When they were here I asked them to replace a light in our double oven, but they noted they would have to remove the oven from the wall to do that and it would be costly, to which I said no thanks. Is it true that the oven has to be removed to replace a light? Another issue is that our double wall oven’s upper unit only gets warm to about 200 degrees. Another issue is that the microwave door open button does not move the door, we have to push it and pull the door open by hand. I have turned to Dacor service and to our local service techs and we are at our wits’ end. Any help here?

We purchased the Model MOH130S in 2006 from a very reputable distributor of high-end appliances. In 2009 we required a service call to deal with temperature control. The oven was out by more than 40 degrees Fahrenheit. This resulted in a relay board, item 101559, to be replaced. Dacor was nice enough to cover the cost of the board, but not the cost of the $152.00 service call. In 2013, guess what? Relay board, this time out by more than 50 degrees, item # 101559 required replacement again only this time it was not covered and cost of $628.00. Here we are, 2016 waiting for the service provider again as temperature is out by over 60 degrees. Roasts, Turkeys, Chickens and everything else have been dying slow deaths in this unit and are awaiting yet another bill to deal with temperature control. Dacor will do nothing until another $150 service call confirms the problem. Hmmm! What to do?

We purchased a Dacor 30 Heritage Gas range and installed it in early Oct 2020. Within a day a gas leak from the back of the range was identified by our gas contractor. Dacor repaired it quickly (12 hours). I was impressed (though concerned it already had an issue). In December 2020 I noticed that the oven indicator light was not coming on. I contacted customer service and despite indicating that there was a problem, was simply told what the light was for. Then, in February 2021 (under 5 months after installation) the oven stopped working. The service technician indicated it was an electrical issue and the gas would not ignite. It has now been over two weeks and we still do not have it repaired nor any indication of when it will be repaired. We spent $5200 on this range. I do not recommend Dacor.

I purchased a Dacor range hood 3 years ago. I had an intermittent problem from the start, as one of the two lights would intermittently go off. Replacing the bulbs didnt fix it. As one light worked perfectly, it became a tolerable issue. Finally, I was having other electrical work done in our home & I asked my electrician to look at it two weeks ago. He figured out that it was a defective lamp housing that incorrectly held the lamp bulb. Dacor shipped me a replacement lamp housing for me at no charge. I installed it this last weekend and it is running fine. Thanks, Dacor!

Wow! I wish I had read this website before we built our house 3 years ago. I have a 5 burner Dacor cook-top that has been nothing but trouble since day one! I have 5 different appliance brands in my kitchen and the Dacor is the only one that has caused continuous problems. I was so mad at the repair man today I hung up on him (poor guy, I see now Dacor is the problem). The cook-top has exploded three times. ow when I say exploded, I am not joking at all. I mean the explosion blew the cook-top up and burners off, blew the cabinet doors underneath open, flames shot out and the house shook. One of the times, my one year old son was standing next to it. I was so upset I ran into the other room with him and sat on the floor and we both cried. It was terrifying! I have had a repair man here 6 times over the last 5-ish weeks (Yes, I didnt have a stove over Thanksgiving and I was the host; its not looking good for Christmas either and we have 4 kids). They have replaced, cleaned and fixed everything possible. They then pointed the finger numerous times at the propane company (which they now have determined it is not a propane problem for sure). Today the repair company called me (by the way, they have been constant contact with their Decor rep Rob about the problems) and said they are done. My expensive 3 year old cook top is not repairable. They have exhausted every possibility. They have been here 6 times and the propane company three times. I have a hole in my granite counter top cut specifically for the cook-top and am told that every cook-top is a different size so I do not know what I am going to do. I called Dacor today and asked to speak to someone who could help me to no avail. I then asked for someone (anyone) to call me back today. You guessed it. Theres been no call back. This is getting really old. How many weeks does this need to go on (dont answer that)? Another problem that I have just lived with is that the stove continually clicks for quite a while after you are cooking. I was told to clean it a certain way. I did that and it didnt work. The repair man did it; it didnt work. The repair man said something was loose inside and tightened it. It still didnt work. I guess I could live with the click. It is the explosions that I need fixed.

Five years ago we built a new house with a big open kitchen for entertaining and family. I like to cook. After talking to a kitchen designer and high end appliance dealer in San Antonio, TX, we decided to go 100% Dacor for the kitchen. What a nightmare! The oven was replaced within the first three months. Since then we have had two relay boards replaced (one within warranty, one not) and one thermostat replaced. When the oven is working, I like it very much. But it is a lot of trouble to get it fixed. The refrigerator defrosting until has gone out three times as well (once in warranty, twice not). Today the unit is not cooling at all. It is hard enough to find someone to service these units outside the big cities, so when we do find someone it takes days for them to get here to diagnose; days to receive parts; and days more to fix. I will never buy another Dacor product! I will say this, the Dacor headquarters have tried to help and even gave discounts on parts, but 5-year appliances should never have these many issues. Our last kitchen was 100% KitchenAid and we never had one problem with anything for 6 years!

We did a full reno on our house starting in 2018. With a brand new kitchen we felt higher end appliances would help finish it off nicely. We settled on Dacor from our appliance dealer due to the look a past history of great reviews. Had we known that the original Dacor no longer existed and it was now Samsung with Dacor nameplate we never would have bought them. We have had 15+ service calls for the fridge and oven. Oven didnt work from day one and required multiple board changes. The interior is not level so you cant bake a cake and the racks are impossible to remove without bending the rails. It just failed again last night just as the warranty expired. The call center is in the Caribbean so dont expect any help from customer service. The ice maker with the fridge is a continual problem so we had to buy an $100 ice maker that now sits on our counter full time. These appliances have a high end price tag but are not high end!

Motherboard on my favor wall oven has been replaced twice. Repairman said not use the self-cleaning feature as that will cause too high of heat and melt the components. Seriously, Dacor? We spend this kind of money and have these type of repair issues constantly. Just glad I finally was told what might help resolve this - I’m ready for a new oven because of all these problems.

I was a bit anxious when I purchased my Dacor range because I really didn’t know how it would perform. A year later and I couldn’t be happier. I love my Dacor 30” range. It has been one of the best purchases ever.

We purchased this unit 7 years ago, just a family of two with visiting grandchildren. Unit came, had a crooked door and a bent latch, which we had serviced and supposedly corrected. When self cleaning the latch still made grinding noises. Over a year ago the oven stopped working period. A December service call said needs a new latch, sensor and display -we are now in 4 figures($). Oven operates for month and a half. January 2019 Service call now new door latch, relay board and main wire harness 4 figures again double! Oven stops working yesterday (June). Service call today new latch, motherboard and something else and another 4 figure repair cost. Same repair parts same problem! Patience is a virtue, but repair costs are sinful! Next step, Boat Anchor! Problem from the beginning and still a problem now.

From the beginning, August 1997, 17 years ago, I was not able to use my oven after self-cleaning. The problem was never resolved after countless service calls totaling over $1500. Aside from the cost, I was inconvenienced every time I cleaned my oven, as I was not able to use it until it was serviced, about a two week wait. I contacted Dacor early on and they reluctantly agreed to extend my warranty for a year. They did nothing beyond that, and my oven still shuts down after self-cleaning, which I hesitate to do at all, until it is beyond needing cleaning! The circuit board was replaced and recently the cooling fan was changed, but....no luck. Buying a new oven is not an alternative, as the oven performs well in every other way and I simply cannot afford one. I cannot believe a company of such status is not interested in satisfying its customers.

Bought to replace 15 year old same model and I'm hoping I will get another 15 years out of this one as well!!! Great price and delivery!

Purchased Dacor Wall Oven EO130SCH in 2011. Rarely used, so never used the self cleaning function. Occasionally wipe with microfiber cloth, eco-friendly cleaners like vinegar and Bon Ami and elbow grease. First problem in 2017 when the oven would not heat up, just before I had guests coming to stay with us. Dacor repair personnel could not make it out for a few weeks, so repaired the issue myself by resetting the thermostat with some creativity and effort. Next problem in 2018 with a U43 relay board error. Can use it for a while if turn off the power to the fuse box for a while, but in 2019 it also started making a clicking noise, and basically not functioning right before I needed it for a party. Cant replace the relay board (which costs more than $300 for the part itself) without pulling out the oven. But why is the relay board failing so quickly? Is there a fan cooling issue? Have talked to Dacor. Poorly designed, poor quality. I would never recommend Dacor.

I purchased a Dacor Double Oven 5 years ago. It is a beautiful design, but unfortunately a piece of junk. Over the 5 years I have had the oven, I have had service technicians repair the oven on 7 different occasions. Unfortunately, my oven is not out of warranty and has failed once again. Today was my 8th attempt at service and the service technician could not get the oven working. I have called Dacor, pleading with them to stand behind their product and to replace this useless piece of equipment. I continue to get L22 error codes, and the main circuit board had been replaced twice. After persistently calling Dacor’s customer service, they finally said they would sell me a new oven at a discounted price to the tune of $4800 plus tax, shipping and installation. I ask myself, why would I want to buy another piece of junk? If Dacor wont stand behind their products, perhaps someone should initiate a class action suit against them.

We remodeled our kitchen in 2002 and chose the Dacor 36 dual-fuel range. I was preparing a pork roast for a dinner party with the oven on Bake. The roast was just not coming up to temperature, though the display indicated that the oven was at the temperature I set. I wound up slicing the roast and cooking it on the griddle; my hungry guests were getting restless. Then I tracked the oven heat for an entire day with an oven thermometer. The oven would come up to temperature and then cool off. I sent these numbers to Dacor and asked customer service for an explanation. Believe it or not, the conversation was--Dacor: The temperature is going down because the fan is coming on. Youre not supposed to use the Bake setting, but only the Convection Bake or Pure Convection. Me: Why is the Bake button there, then? Dacor: Were taking it out in the next production run. (This hasnt happened. My sister-in-law bought a Dacor last year before I could warn her and the button is still there.) Also, after using the self-clean one time, I noticed a crack on the inside of the oven door, starting in the corner of the window. The inside of the window is now permanently spotted with baked-on grease. Now my oven does not work at all. The repairman says that the circuit board needs to be replaced, and if Im lucky, it will work for a couple of years. The repair will cost around $700 including labor. The repairman told me that some repairmen in our area will not even work on Dacors because there are so many problems. Im considering replacing the stove... a very expensive mistake. Beware of Dacor products.

We got a U43 relay error on our Dacor oven of 4 years. When we finally add up the cost to replace the part, it will exceed $500 and Dacors only response is, Sorry, it is out of warranty. Of course I do not understand why a relay board on an oven would short out after a few years. Not happy and would not recommend the manufacturer.

We purchased a Dacor Epicure Range for approximately $10,000 and have had one repair after another because the burners leak gas, endangering our family. Weve spent almost $3,000 on repairs and the repairman has told us that hes never seen such a pervasive gas leak. To manage the cost of repairs, weve literally turned the gas and stove off for periods of time to cook on other appliances. While I love the design of the stove and specifically selected it over Wolf and other high end brands, I now wish I had gone with another brand. I have reached out to Dacor about this but they have not been willing to stand behind their product.

We love our Dacor 36 refrigerator. We have owned it for 6 years and never had a problem with it. Our friends and family have also complimented the look and style. We are happy with our purchase and would recommend Dacor products to anyone.

Warning: Warning, safety hazzard for all, adults and children. Recommendation: The knobs should be set on the top of the stove, not the front where children can reach. Control knobs should click when fire and gas is turned off, and highest flame setting should be at the end of the turn just like a clock. I inherited this range as new owner of the house. Today I used the high flame option of the gas stove. When I was done with cooking, I turned off the gas according to the knob position, front of the turn. Later I discovered the range was not exactly off. It was still hot but no flame could be seen.I checked by sight the control knob position, it was set incorrectly in off. Then I touched it and realized the knob actually has a bit more to go to the end, slightly before the off position. Therefore it continues to release gas with unobservable flame. This knob does not click when user turns it to the off position. It is just a silent knob with an inaccurate cue of a heavier black line for off and on indication. Besides, high flame setting comes at the beginning of the turn of the knob rather than the end, it is counter intuitive to our mind of increase heat by turning the knob further on, like our clock. Oven racks are hard to put back after cleaning. Once a rack almost tumble out while food was sitting on it.

I have a Dacor MORS130SS oven that I purchased in July of 2008. After 6 months the first membrane panel failed, one year later the second membrane failed. One year later the third membrane failed. Im on the fourth membrane and now my fine Dacor is burning things!! I can set the temp to 350 and it shows 350 on the display but the lower element never shuts off and whatever I cook gets burned. I bought this oven thinking it might be my last considering the supposed quality of Dacor. I know for sure it wont be my last oven!! I sell appliances and I never recommend Dacor ovens because of all the continued problems. Ive never used the self clean feature since being told by a Dacor tech trainer that he didnt recommend using self clean because it would cause the oven to age faster. Wonder how long it would have lasted if I did use self clean? Sure wish Dacor would contact me for a testimonial!

Our new ranch has three Dacor microwaves, only one of which has had a few months of use. The others have very limited use. To this point weve not had problems, but given the opportunity to redo the purchases wed go with a popular brand, i.e., LG, GE, Panasonic. They are more flexible, parts are available, and all three combined would probably cost less than one of these. In fairness, I personally feel the same about our other high end appliances, Wolf, Viking, Sub-Zero and Asko. None beats our former appliances. Maybe its just about show.

I bought this beautiful range and choose Dacor but when we used the Green Clean on it the enamel pealed off a spot on the bottom of the oven a 2x4 inch patch. Now Dacor say that this is cosmetic and will not honor their warranty. I have been calling them daily because they do not call me. Their service sucks.

We bought our Dacor 30” gas range in September of last year. We were tired of cheap stoves that lasted 5 years before they needed to be relegated to a landfill. We thought it was an investment that would provide us with a reliable appliance and worst case scenario, better warranty repair service than Home Depot or other big box store.After 15 months, the igniter for the oven stopped working. We tried the 800 number on the warranty registration website and no one there could bring up our registration, even though I could see it on the website. They gave me an email address to contact the people who could look it up and I heard nothing for two days. I called the 800 number again and they transferred me to another number and they finally found our warranty registration and issued a ticket for the repair.The company they use for warranty work in Toronto, is Home Appliance Repair GTA and they are absolutely horrible. They said they ordered the part on November 27, but they did not actually order it until December 6th. Dacor then sent the wrong part! I demanded that they send the proper part overnight and on December 13th they called and left a voicemail saying that the part would be here by today at the latest.It did not arrive and this evening I emailed them again and their response was that the part would be here on December 19th. How does it take a week in this day and age to deliver anything? I don’t believe that I will even have a functional oven for Christmas this year. I have already given up on any baking getting done. I will never buy a Dacor product again. I actually really love my stove, but I am beyond disappointed with their warranty service and customer care.

We purchased a Dacor Oven model # ECS 136544 in 2009. Within two years, the relay board and thermostat in addition to an LED bulb required replacement. A year later, the broiler heating element and the second LED light required replacement. Dacors response (800-793-0093) was read your explicit warranty and the implied warranty under Section 2-314 of the Uniform Commercial Code isnt applicable. The total expense for repairs is over $1,000. Did we get a lemon, or are Dacor ovens prone to failure? Should we have been thinking Wolf?

Our Dacor wall oven (model MOH 1305) is the subject of my concern. Purchased with confidence in Dacor’s advertising in 2008. The oven has had multiple visits by a Dacor authorized repair company who along with a Dacor technician determined that the oven needed a relay board replacement. This relay board has been replaced twice and has failed after installation both times. The relay board provided by Dacor appears to be the problem. Each repair/service call costs approximately $300.00 with no guarantee that the next relay board will work. Our conversations with Dacor give us no satisfaction. Dacor now tells us that our “superior product” of 11 years is just too old. Additionally, they tell us that Dacor products are “superior products” that are designed to last somewhere between 10 to 15 years. There is no excuse for Dacor since the replacement relay boards they are sending us seem to be defective. Their excuse that we have an “old” oven is wrong since the problem is with their defective replacement parts. Beware consumers when thinking about purchasing Dacor products.

We purchased this range after remodeling our kitchen. We opted for the Dacor because of the deep oven that the other high end ovens did not have. I am an avid baker so this was a plus. After a year and half the oven stopped working, it was not getting hot. Thankfully is was still under warranty and it was repaired. The technician determined it was the oven control thermostat that was not working. Fast forward two years and again the same problem, along with the right front burner now also not working. And wouldnt you know it, the warranty is expired. Another technician came out again and stated to fixed the two problems it would be approx $250.00 just for labor and not including parts. CRAZY INSANE!!! If we would have known all the problems and we would have purchased either a Wolf, a Thermador or even a Monogram. How can so many issues and problems be happening with an range that is only 4 years old? Especially one that costs over $6000. It has to be a lemon or poorly manufactured. Ive contacted Dacor and was told they need to review my file to make a determination on what they want to do. REALLY, you dont need to be a rocket scientist to know there is a problem. Theres lemon laws for cars, why not appliances????

The first F1 Error needed a new membrane repair for $470.00, after 4 years of service. Now, the same F1 error after the new membrane is only 13 and 1/2 months in service and it is now out of warranty. Customer service people are rude and unhelpful but when pressed, they said they might be willing to help after a service tech, which I have to pay for, diagnoses the problem.Even the Sears store people advise their customers not to buy Dacor products and that is sad because it is one of only 2 American made options. Dacor needs to step up their product engineering, commitment to quality and get rid of the rude phone people in Customer No Service. This is not the end of this experience but the only reason I am not junking the stove is because a comparable replacement is another 3000 bucks from another vendor which I cannot afford at this time.The irony of this is that the company clearly knows they have problems but when I asked if the replacement parts had been improved so the problems wont persist, I was told that no changes or modifications to the electronic brains had been made. How stupid is that! They are just asking for more problems with the parts they send you to fix what does not work.

I replaced my Thermador Wall ovens with Dacor because the size and I would have to do less retro-fitting of my cabinetry, this was a grave mistake. Here are the issues with Dacor.1. The high heat sensor trips and you need to call a service professional to have it reset. This gets very expensive. I have tripped mine three times, once baking a cake at 350 degrees, once during self-cleaning and another during normal cooking. The Dacor Service Help said this was a common problem because the heat sensor is located near to the touch panel.2. The oven vents from the bottom of the unit into the room heating my kitchen.3. The glass window does not seal so I have stains in-between the panes of glass. Not very attractive to stare at large drip stains.4. It takes an exceptionally long time to pre-heat oven and convection mode even longer.5. The temperature cycles through and does not maintain its cooking temperature causing underdone results and longer cooking times. This is especially challenging when cooking roasts and large turkeys because they may take up to an hour longer than expected.Overall, I do not recommend this product.

The electronics on the first two induction burners failed within six months which was covered under warranty. The second two went three weeks after the warranty and we had to argue with Dacor to cover them otherwise it is a $1400 repair job. From day one whenever you open the oven door the controls and heat shut off. Sometimes it turns back on when you close the door. As for the downdraft, it worked fine until 10 weeks ago when while closing, the cover lip hit a wooden spoon that had been lying flat near the edge. There is no safety feature and the motor continued to try and close the fan. The unit would not respond and would not re-open. The spoon had to be broken to get it out. If this was a childs finger you would have had to call 911. We now have a repair bill of over $350 and are still waiting for 2 months for Dacor to send a part. We will never buy this brand again.

We remodeled our kitchen in 2007 and bought the High-end Dacor side by side fridge and oven set. The fridge has been down FIVE times in 8 years and we have replaced elements, etc on the stove at 5 years. Horribly built and product support has been near non-existent, even during warranty period. I would not recommend this product line to anyone. If it was just one appliance or the other OR if the product support was there, I would not be as upset! We spent over $15,000 and have had nothing but headaches and lost $s on repairs and food that was thrown away.

Updated on 09/08/2019: Received a long apology from Dacor regarding their complete inability to service our range stating they would make it right. After sending them all my contact info privately at their request, we have heard nothing. My husband drove to Houston to their showroom, met with Dacor rep out of California, still nothing. Note there are only a few suggested repair services on their website which none cover our area. Avoid Appliance Genius. They wanted $ 500 just to drive 50 minutes travel cost. So here we sit, broiler in main oven out, lighters do not work, and the control screen is blank. Yes, Dacor was great until something broke.Original Review: Our Dacor range was great until it started needing repair. First the broiler went out in the main oven. Then some of the lighters quit working. When we called for repair, every place we called said they would no longer service Dacor because they were unable to get parts. For over a year we have gone back and forth with Dacor state office. They finally sent a “tech” from a video repair store. Really. He charged us $170 to drive to us. Then said he couldn’t get the brass rings off the burners, sorry. Called Dacor again and they said if we found anyone to let them know!!! Yesterday, the the touch panel burned out. I’m done. Dacor does not stand behind their products. I have documented all conversations. Do not buy Dacor.

I moved into a house that already had a Dacor unit in place. Within months, I discovered that I owned an oven that could be fixed by throwing the circuit breaker. Then, I learned about invisible hands that turned the 325 degree convection oven to a 500 degree broiler. The final act was having all three glass panes shatter and the control panel cracking as punishment for assuming that the oven cleaner on an expensive gourmet stove would function according to manufacturing standards. The repairman ordered replacement parts. He spoke with someone who was off shore so forget about Dacor being all American made. The wrong parts were sent. He has reordered. Meanwhile, I have been without an oven for two months. If this goes on, I am going to Home Depot and buying a Hotpoint or GE. It is the same price as replacement glass panels and the control panel.

Our Dacor oven is 2 years old and the oven door stopped closing all the way, rending it inoperable. The company is now owned by Samsung. I tried to schedule a service call to repair/replace the door hinges. This should be a simple process. However, because I purchased the oven through a designer and Dacor dealer, I had to track down the order verification to demonstrate that I am the original owner of the oven (this is in addition to providing a copy of the receipt or proof of purchase). It took several days to resolve this issue with my designer and rep who sold me the oven. Then, I scheduled the service call on the phone only to receive an email hours later advising me that the service call had been cancelled. No explanation was provided. After rescheduling the service call several times only to have each call cancelled, something finally worked with Samsungs tracking system and the service call actually took place.Dacor is the Mercedes of ovens and I expect a service call to be a little more expensive. However, other providers of luxury products facilitate the product support to minimize customer aggravation. Samsung needs to work on its product support and customer service. I would not purchase a Dacor product again since there are several other manufacturers that provide comparable luxury kitchen appliances with much strong customer support.

Weve had these appliances for 15 years. The cooktop has worked well. However, it could be improved with a lower lever for heating on its small burners, allowing it to simmer water rather than boil. The Dacor exhaust we purchased is one of those type that pop up out of the counter. It works but leaves much to be desired. When it runs, it pulls so much air the flame goes out on the burners. It is still not efficient at getting rid of cooking smells or smoke either, but that is simply a problem with all of this design so I cant fault Dacor. We have the biggest problem with the double oven. There are three main issues: 1) Whenever we run the self cleaning function, it pops the heat safety switch inside the oven housing so I need to take it apart to fix it. Hence we work to keep it clean so we never use the cleaning cycle. 2) The oven door gaskets prevent to door from closing and sealing all the way. The door tilts out app. ¾ because of this. We were told by the service guy who came to fix problem 1 above that this is the way the doors are(!). Our bottom one also tilts out but not as much. Ive dealt with this for 14 years! 3) We have to sand the burner electrodes on the cooktop to ensure they spark to light the burners at least 2-4 times per year. Not sure if that is normal or not.

This is the second time I have purchased these appliances and unfortunately each one has been a great disappointment. I have spent enough in repair bills to almost purchase a warming drawer. Each one shuts down when the self clean button is turned on, and then I have to call a repairman out to recalibrate the oven to work each time I try to use the self clean. I was told by the last repairman that the life of the oven is greatly shortened if you the self clean mode. If this is the case, either fix it or take out this mode. After I had the oven about a year the oven door glass blew out, and this had to be replaced. The temperature in the oven is very unreliable in different areas of the oven and browns more on one side than the other... For the high end cost of these ovens, I would just as soon have a basic oven that works and does not go out every few months. What a waste of money I consider Dacor to be, and will never recommend it to anyone I know. I am in the personal shopping business and have my own company, but will tell my clients to be very aware of the high cost/low performance of Dacor products... On a scale of 1 to 10, Dacor gets a 1.

We are in the process of remodeling our house including an entire new kitchen that we cant wait to finish to invite people over and show. HOWEVER, the cook top already has a light burned and finally the cover of it ended up falling as I was wiping down the stove (very softly by the way because I like to treat my appliances really nice). We have had this stove for less than a year I havent even made the last payment and it is already with a light burned out. REALLY? My husband spent countless hours researching the best appliances and decided to get this one and to come to find out that it is not good it is a complete disappointment. I am sooo upset. DO NOT BUY THIS BRAND!!! Save yourself the hassle that we are now going to go through trying to get a hold of someone on the phone and see what they will do if anything. I bought it from AJ Madison.