Appliance Types


Appliance Brands


Article Categories


More Articles


GE Appliances
GE Appliances

GE Appliance Error Codes

GE Appliances is your home for the best kitchen appliances, home products, parts and accessories, and support.


Dishwasher Error Codes

CODE: number + H  
PROBLEM: The dishwasher is in Delay Start mode.  
FIX: For more information on this feature, please view: Dishwasher Delay Start Option. 

CODE: C1  
PROBLEM: The pump out during drain has exceeded 2 minutes.  
FIX: Clean the air gap. Replace or reposition the hose. Run the disposer to clean it out. 


CODE: C2  
PROBLEM: The total pump out cycle exceeds 7 minutes.  
FIX: Press RESET to stop the beep. 

CODE: C3  
PROBLEM: The dishwasher will not drain  
FIX: Disconnect the power at the circuit breaker for about 30 seconds and then reset the dishwasher. 

CODE: C4  
PROBLEM: Machine filled twice after a power failure. Float switch stuck or failed. Clogged drain or sump. FIX: Touch start and then cancel/reset. Tap on the float cover to un-stick the float. This is the plastic cover that looks like an upside down cup in the front left corner of the floor of the dishwasher. Also, check the sump area in the back bottom of the tub for debris. It looks like an upside down silverware basket and can become clogged. 

CODE: C5  
PROBLEM: The pump out time is too short.  
FIX: Make sure that the water supply is turned on. Try the same cycle again. Tap on the float cover to un-stick the float. This is the plastic cover that looks like an upside down cup in the front left corner of the floor of the dishwasher. 

CODE: C6  
PROBLEM: Water temperature is too low.  
FIX: Water temperature coming into the dishwasher should be at least 120 degrees F. Run the faucet adjacent to the dishwasher prior to starting the dishwasher to purge any cold water from the line. Adjust the water heater temperature. Don't use the washing machine or take showers when using the dishwasher. Use options on the dishwasher to cause the machine to run longer and thus add more heat. 

CODE: C7  
PROBLEM: The dishwasher's water temperature sensor circuit has become inoperative.  
FIX: Disconnect the power at the circuit breaker for about 30 seconds and then reset the dishwasher. 

CODE: C8  
PROBLEM: This display indicates that the detergent cup is blocked from opening fully.  
FIX: Remove obstruction (i.e. silverware, pan). Relatch door and wait 30 seconds for cup to open. Dishwasher Soap Cup Did Not Open 

CODE: PF code  
PROBLEM: Indicates that there has been a power failure to dishwasher.  
FIX: Simply select the desired cycle and options, press the Start pad and the dishwasher will function normally. 

CODE: Cup Open  
PROBLEM: The detergent cup has not been closed. It's a reminder to add detergent and latch the cup closed.  
FIX: When the problem occurs, the cycle will not start, but you can override by pressing the start pad again without opening the door. 

CODE: LEAK DETECTED  
PROBLEM: Possible leak is detected.  
FIX: The cycle will be cancelled on models with leak detection. 

CODE: H2O  
PROBLEM: Indicates a low water situation  
FIX: If H2O only appears during 1-Hour Wash, schedule service. Feel free to run any other cycle until that update is done. If H2O appears during other wash cycles (AutoSense, Heavy, Normal or Light), then double-check that the inlet water hose is not kinked. 

CODE: PrS  
PROBLEM: Indicates the pressure sensor is sending an invalid signal to control. Cannot start cycle or it will cancel.  
FIX: Most likely this is a harness or sensor issue. 


Dryer Error Codes

CODE: 000 
PROBLEM: No errors 
FIX: No problem was detected. No fault codes are stored in the memory.

CODE: 001 or 003 
PROBLEM: The inlet thermistor (temperature sensor) is defective 
FIX: The inlet thermistor on the side of the inlet air duct inside the dryer measures the temperature of heated air entering the dryer drum. Unplug the dryer and reconnect any loose wires on the inlet thermistor. Replace the wire harness if damaged. If the wires are okay, replace the inlet thermistor. 

CODE: 002 or 004 
PROBLEM: The outlet thermistor (temperature sensor) is defective 
FIX: The outlet thermistor on the blower housing behind the fan measures the temperature of heated air leaving the dryer drum. Unplug the dryer and reconnect any loose wires on the outlet thermistor. Replace the wire harness if damaged. If the wires are okay, replace the outlet thermistor. 

CODE: 005 
PROBLEM: The main control board is defective 
FIX: Unplug the dryer for 3 minutes to reset the main control board. Replace the main control board if the code returns when you restore power. 

CODE: 006 
PROBLEM: Stuck button on the control panel 
FIX: Push each button on the control panel to free the stuck button. If the code doesn't clear, unplug the dryer and replace any damaged control panel components. If the control panel components are okay, replace the main control board. 

CODE: 007 
PROBLEM: Power supply is mis-wired 
FIX: The Line 2 (L2) and Neutral (N) are reversed. Correct the power cord wiring connections on the terminal block, following the installation instructions. 

CODE: 008 or 00d 
PROBLEM: Door switch not opening; 5 cycles ran without the door switch opening 
FIX: Unplug the dryer and reconnect any loose wires on the door switch. Replace the wire harness if damaged. If the wires are okay, replace the door switch. 

CODE: 009 
PROBLEM: Drive motor problem 
FIX: If the drive motor won't run, unplug the dryer and reconnect any loose wires on the drive motor. Replace the wire harness if damaged.


Microwave Error Codes

CODE: F1  
PROBLEM: Open Thermal Sensor, due to excessive heat in microwave cavity 

CODE: F2  
PROBLEM: Shorted thermal sensor 

CODE: F3  
PROBLEM: Shorted touch pad panel 

CODE: F4  
PROBLEM: Open humidity sensor 

CODE: F5  
PROBLEM: Shorted humidity sensor 

CODE: F6  
PROBLEM: Shorted temperature probe 

CODE: F10  
PROBLEM: Shorted touch screen 

CODE: Probe  
PROBLEM: Open temperature probe or the probe is not plugged in during a temp cook function. Make sure probe is firmly inserted into the wall of microwave and the food item. 

CODE: 888, 8888 or PF  
PROBLEM: It is possible to see this display upon initial installation or after power was restored due to a power failure. This display can be cancelled and normal operation resumed by touching the CLEAR pad. The clock can be reset on models so equipped. 

CODE: 18 power watch code  
PROBLEM: Indication of an issue with the electronic control in the microwave. 
 


Range Error Codes

CODE: F0 
PROBLEM: Clear/Off key error 
FIX: Unplug the range for 3 minutes to reset the electronic control board and then restore power. If the code returns, replace the glass touch control panel. If the problem continues, replace the electronic control board. 

CODE: F1 or FF 
PROBLEM: Defective electronic control board 
FIX: Unplug the range for 3 minutes to reset the electronic control board and then restore power. If the code returns, replace the electronic control board. 

CODE: F2 
PROBLEM: Oven over-temperature 
FIX: If the oven overheated, the electronic control board likely has a stuck relay; replace the electronic control board. If the oven is at room temperature, the oven temperature sensor could be defective. 

CODE: F3 
PROBLEM: Oven temperature sensor is defective (electrically open) 
FIX: Unplug the range, disconnect the oven temperature sensor and check the resistance of the oven temperature sensor using a volt/ohm meter. The oven temperature sensor should measure around 1100 ohms at room temperature. 

CODE: F4 
PROBLEM: Oven temperature sensor is defective (electrically shorted) 
FIX: Unplug the range, disconnect the oven temperature sensor and check the resistance of the oven temperature sensor using a volt/ohm meter. The oven temperature sensor should measure around 1100 ohms at room temperature. 

CODE: F5 or F6 
PROBLEM: Gas lockout valve failure 
FIX: Unplug the range and check the gas lockout valve wiring. Reconnect any loose wires. Replace the wire harness if damaged. If the wiring is okay, replace the gas lockout valve. 

CODE: F9 or FC 
PROBLEM: Oven door lock failure 
FIX: Unplug the range and secure any loose connections in the wire harness between the oven door lock assembly and the electronic control board. Replace the wire harness if damaged. Check the oven door lock assembly and replace it if damaged. 

CODE: FD 
PROBLEM: Defective meat probe 
FIX: Unplug the meat probe (allow the oven to cool before unplugging the meat probe). If the FD code disappears once the meat probe is unplugged, then replace the meat probe because it's defective.


Refrigerator Error Codes

CODE: FF  
PROBLEM: Check frozen food for thawing because the temperature is rising too high. 

CODE: PF  
PROBLEM: The power to the refrigerator has been interrupted. 

CODE: CI  
PROBLEM: Check the icemaker for proper operation. 

CODE: dE  
PROBLEM: The defrost system has not operated properly in the last 24 hours. 

CODE: CC  
PROBLEM: Check the temperature controls because the temperature for the refrigerator is incorrect.


Washer Error Codes

CODE: 1 flash 
PROBLEM: Motor failure 
FIX: Unplug the washer and replace the drive motor. 

CODE: 2 flashes 
PROBLEM: Slipping drive belt or loose hub nut on the spin basket 
FIX: Unplug the washer and replace the drive belt if loose or damaged. If the drive belt is okay, tighten the hub nut on the spin basket. Replace the drive motor if the drive belt and hub nut are okay. 

CODE: 3 flashes 
PROBLEM: Defective inverter control 
FIX: Replace the drive motor; the inverter control is part of the drive motor and isn't sold separately. 

CODE: 4 flashes 
PROBLEM: Mode shifter circuit failed 
FIX: The mode shifter is a component on the drive shaft assembly. Reconnect the wire harness between the inverter control and the mode shifter if loose or disconnected. Replace the drive shaft assembly if the mode shifter is defective; the mode shifter is part of the drive shaft assembly and isn't sold separately 

CODE: 5 flashes 
PROBLEM: Motor failure 
FIX: Unplug the washer and replace the drive motor. 

CODE: 6 flashes 
PROBLEM: Locked rotor on the drive motor 
FIX: Replace any drive system components that prevent the drive motor from rotating. If drive systems components are okay, replace the drive motor. 

CODE: 7 flashes 
PROBLEM: Lid didn't open for 4 consecutive cycles 
FIX: The inverter control expects to see the lid switch open after every cycle. When 4 cycles are completed without the lid switch opening, the inverter control assumes that the lid switch is defective. Unplug the washer and repair or replace the lid switch wire harness. If the wire harness is okay, replace the lid switch. 

CODE: 8 flashes 
PROBLEM: Motor overheated 
FIX: Reduce the load of laundry if the washer is overloaded. Replace any drive system components that prevent the drive motor from rotating freely. If drive systems components are okay, replace the drive motor. 

CODE: 9 flashes 
PROBLEM: Motor brake mechanism is defective 
FIX: Unplug the washer and replace the drive motor. 
 


Water Heater Error Codes

CODE: FA 
PROBLEM: Compressor discharge temperature not rising 
FIX: The T4 sensor (compressor outlet temperature sensor) must detect at least a 20-degree temperature rise during the first 30 minutes of run time. Disconnect the power or unplug the water heater and check T4 sensor mounting, wiring and ohm resistance. 

CODE: FB 
PROBLEM: Compressor discharge temperature not stable 
FIX: The T4 sensor (compressor outlet temperature) must be greater than 120 degrees Fahrenheit after 30 minutes of run time. Disconnect power or unplug the water heater and check T4 sensor mounting, wiring and ohm resistance. 

CODE: FC 
PROBLEM: Evaporator frosted over 
FIX: The T3a sensor (evaporator inlet temperature) must be greater than 20 degrees Fahrenheit after 30 minutes of run time. Disconnect power or unplug the water heater and check T3a sensor mounting, wiring and ohm resistance. 

CODE: FD 
PROBLEM: Super heat is too low 
FIX: Disconnect power or unplug the water heater and then check temperature sensors T3a, T3b and T5 mounting, wiring and the ohm resistance of each sensor. Check and clean the filter. 

CODE: FE 
PROBLEM: Discharge temperature above the limit 
FIX: The compressor discharge temperature exceeded 240 degrees Fahrenheit. Verify that T4 sensor (compressor outlet temperature sensor) measures approximately 188k-2k ohms after 30 minutes of run time. Disconnect power or unplug the water heater and then check T4 sensor mounting, wiring and ohm resistance. 

CODE: F2 
PROBLEM: Tank temperature sensor failure 
FIX: The control checks the T2 tank sensor temperature before the compressor starts and it must be 30-u2013170 degrees Fahrenheit. Disconnect power or unplug the water heater and then check T2 sensor mounting, wiring and ohm resistance. 

CODE: F3 
PROBLEM: Compressor failure 
FIX: The control energized the compressor but the current sensor does not detect any current flow. Disconnect power or unplug the water heater and then check the compressor, relay and wiring. 

CODE: F4 
PROBLEM: Fan failure 
FIX: Disconnect power or unplug the water heater and then check the evaporator for a loose or broken wire connection. If fan motor wiring connections are okay, replace the evaporator fan motor. If the F4 code returns after replacing the evaporator fan, replace the power control board (PCB). 

CODE: F5 
PROBLEM: T3a sensor failure 
FIX: Before the compressor starts, the control checks that T3a, T3b and T5 sensors are all within 15 degrees Fahrenheit of each other. Disconnect power or unplug the water heater and then check T3a sensor mounting, wiring and resistance. 

CODE: F6 
PROBLEM: T3b sensor failure 
FIX: Disconnect power or unplug the water heater and then check the T3b (evaporator sensor) sensor mounting, wiring and the ohm resistance of the sensors. 

CODE: F7 
PROBLEM: T4 sensor failure 
FIX: Disconnect power or unplug the water heater and then check the T4 (compressor outlet sensor) mounting, wiring and ohm resistance of the T4 sensor. The ohm resistance of T4 sensor should measure approximately 55k ohms at 77 degrees Fahrenheit. 

CODE: F8 
PROBLEM: T5 sensor failure 
FIX: Disconnect power or unplug the water heater and then check the T5 (ambient temperature sensor) mounting, wiring and ohm resistance. The ohm resistance should measure approximately 10k ohms at 77 degrees Fahrenheit. If the sensor is okay, replace the power control board (PCB). 

CODE: F9 
PROBLEM: Lower heating element failure 
FIX: Disconnect power or unplug the water heater and then check the lower heating element and wiring. Check the wiring and connections on the power control board (PCB) and lower heating element. 

CODE: F10 
PROBLEM: Upper heating element failure 
FIX: Disconnect power or unplug the water heater and then check the upper heating element and wiring. Check the wiring and connections on the power control board (PCB). Disconnect and measure the heating element for ohm resistance using a multimeter.



GE Appliance Error Codes

GE appliance fault codes

GE appliance diagnostic codes

GE appliance error symbols

GE appliance common faults


Product Reviews:

I love the way the dishwasher is so quiet and cleans the dishes well. Howev
I love the way the dishwasher is so quiet and cleans the dishes well. However, they are ALWAYS WET. A repairman came and told me that I could not expect the dishes to be dry on the light cycle with the POWER DRY. He told me I have to wash on the normal cycle. I did that and they are still wet. He came back out again and basically had no viable explanation. I have to have a dish towel in hand to dry the dishes as they come out of the dishwasher. I paid a lot of money for what I consider the piece of junk that is sitting in my kitchen. I will never again buy a GE PRODUCT.
Published: June 5, 2017
ANN of Murfreesboro, TN
Source: consumeraffairs.com

Almost immediately after purchasing the GE microwave we started having prob
Almost immediately after purchasing the GE microwave we started having problems with the circuit board. It is now totally on the blink after only 4 years. This was a high price appliance. Sometimes when setting the timer on 30 seconds, the microwave would still be running and after looking at the timer it would still have 4 or more minutes left to cook. This is a FIRE HAZARD! We have lost food from timer malfunctions. This is a product I would be afraid to purchase. I am wondering why cant there be recalls on these cheaply built defective microwaves since you read of the same malfunctions over and over. GOODBYE GE!
Published: July 23, 2015
Jeff of Savannah, GA
Source: consumeraffairs.com

On 05/04/2014, our GE microwave over the stove unit burst into flames. My w
On 05/04/2014, our GE microwave over the stove unit burst into flames. My wife was sitting in our family room and heard the microwave fan start (spontaneously). Then she observed flames reflected in the kitchen window. When she went to the kitchen, she observed the interior of the microwave was aflame. The fire was extinguished with a spray bottle of water. The burning items appeared to be insulation. The fan from the microwave was with the burning insulation on the rotating plate.
Published: May 5, 2014
Dave of Milwaukie, OR
Source: consumeraffairs.com

I bought a GE microwave in June 2011. Paint started peeling off the inside
I bought a GE microwave in June 2011. Paint started peeling off the inside top soon after purchase. Now, all the paint is gone and GE doesnt care and Walmart wont replace it. So today, I bought a Panasonic. Maybe it will last. Its fifty dollars cheaper, too.
Published: July 25, 2012
Brenda of Frost, tx
Source: consumeraffairs.com

It doesn’t do the best job of cleaning without rinsing first. Start butto
It doesn’t do the best job of cleaning without rinsing first. Start button is difficult to operate and plastic membrane worn through. Both shelves began rusting within a few years. But no mechanical/electronic issues ever.
Published: February 23, 2021
Michael of Phoenixville, Pennsylvania
Source: consumeraffairs.com

I purchased a GE Smart water heater and installed in October 2004. I have n
I purchased a GE Smart water heater and installed in October 2004. I have not had any issue or problem. 50 gallon natural gas unit for 5 people. 40,000 BTU I am looking to replace before there is a problem and will certainly look at GE again, but these more recent reviews are a concern. The trouble is, these websites attract those who are dissatisfied and may give a biased view of a product.
Published: November 11, 2016
GEO of Gurnee, IL
Source: consumeraffairs.com

I have just purchased a new GE dishwasher because mine just broke after 35
I have just purchased a new GE dishwasher because mine just broke after 35 long years of excellent service. I am so completely satisfied with your GE products, and I would like to tell you also that the double oven stoves are still working well.
Published: June 14, 2013
Lottie of Clearwater, FL
Source: consumeraffairs.com

The dishwasher is new and looks great. However the dishes are not getting c
The dishwasher is new and looks great. However the dishes are not getting clean. After washing with a 200+ minute wash cycle utensils are still dirty and food particles are left on plates and bowls. This is occurring even with a good rinse prior to placing them into the dishwasher. I clean out the food particles filter after every two loads, makes no difference. Also the water bottle jets are a nice idea but water bottles are too tall to fit even with the third rack removed. I am very displeased with my purchase. This was not an inexpensive model.
Published: January 20, 2019
Elizabeth of Oak Ridge, NJ
Source: consumeraffairs.com

Our dishwasher has gotten very warm mid-cycle and now trips the breaker in
Our dishwasher has gotten very warm mid-cycle and now trips the breaker in the house each time we run the cycle. The problem became evident in April 2012. We have called in a GE repair person to fix it and they said it was a heating issue and not repairable. We have not used it since, but have not replaced it with a new one yet. In August, we read about the recall of a similar model number manufactured within same time frame. Our machine model is PDW7300J03WW, the recalled model is PDW7. Our machines serial # is **. Strangely, the serial number is not listed in the recall, even though symptoms are exactly the same!We have called GE Consumer Affairs at 1-800-386-1215 four times, the most recent today, 9/14/2012. Each time we call, we are left on hold for 59 minutes only to be disconnected automatically! I am sending a registered letter to GE CA with a copy of this link and intend to contact my local news if I do not receive sufficient response within the week. Does GE need to see an actual fire report from my fire department or worse in order to get their attention to replace the unit? It is disgraceful and extremely dangerous.
Published: September 14, 2012
Marisa of Yonkers, NY
Source: consumeraffairs.com

In early 2017, we bought all of our GE Profile appliances including the dis
In early 2017, we bought all of our GE Profile appliances including the dishwasher through our builder as part of building a new home. Love the slate exterior. Love the whisper quiet of the appliance. I do NOT like the way it cleans my dishes. Most of the time, the soap isnt even distributed. The soap compartment is opened but most of the soap is still there. Ive followed the instructions on loading to ensure my dishes arent blocking the water that is supposed to spray up and help distribute soap. Even though I select the dry function, my dishes are sopping wet when the cycle is finished. We have to catch the end of cycle and crack the dishwasher open to let the steam escape in order to cut down on the wet. Even then, we still have to dry dishes to put them up. We have a water softener and have verified its working so I know thats not causing these issues. I would not recommend this dishwasher.
Published: January 21, 2020
Vicky of Spring Branch, TX
Source: consumeraffairs.com

I had the same issue as an earlier post regarding my GE microwave. One day
I had the same issue as an earlier post regarding my GE microwave. One day the the screen said keyboard shorted, later that day the microwave began turning on by itself. I called GE and they said this is the first they have heard of it. Clearly this has happened before. GE needs to step up and take care of this issue before someones house burns down due to this issue.
Published: August 1, 2011
Kevin of West Hartford, CT
Source: consumeraffairs.com

I had a problem with my GE Profile Dishwasher that I had for several years
I had a problem with my GE Profile Dishwasher that I had for several years and I had it on factory warranty. However, the last time they came to repair, they did not have parts available to fix anymore. So, they recommended new one. I worked with Consumer dept and made arrangements to replace with one they recommended at $500+. After several efforts to get it delivered, it was and we began using. It is not a Profile like my old one and it does not have the additional washing, rinsing and drying cycles as the Profile. It is a flat out bottom line washer. No, sani clean etc.. We have used the machine about 4 times and each time we have to rewash several of the dishes and especially the silverware. This is the most disgusting piece of equipment I have ever used. My home is loaded with GE products from years ago, mostly the Profile series and I have been delighted with the products and service. This machine is a disaster. I cannot believe that GE has this on the market or maybe this is a machine they use to satisfy customers who may threaten to use someone elses. It was not free, as I say it cost over $500. The stores and onlines advertise better machines on sale for less. I have GE stock which I will sell. They are going down on Quality. Consequences: Stuck with poor machine that does not do job that I paid good money for. Really, GE, get yourself together. Product Model:GDF510PSD1SS.
Published: December 5, 2013
Robert of West Roxbury, MA
Source: consumeraffairs.com

Its been a decent dishwasher. Usually residue left on something. Even with
Its been a decent dishwasher. Usually residue left on something. Even with rinsing. And weve tried all brands of detergent. Rinse, China, speed cycle, normal, pots/pans and anti-bacteria cycles. 9 hour delay and extra hot wash and heat dry settings. It works for our family. A load every 2 days or so. Its almond/bone colour. The hoses are flimsy. They seem like they could leak at any moment. Not sure Id buy another GE.
Published: February 24, 2016
Craig of Kingston, ON
Source: consumeraffairs.com

We have enjoyed this dishwasher for over 25 years. Over 25 years ago my hus
We have enjoyed this dishwasher for over 25 years. Over 25 years ago my husband gave me a portable dishwasher for Christmas. About 15 years ago we turned it into a built in. It doesnt look great, some rust and lost 2 of the prongs but it is still doing a great job.
Published: December 8, 2016
Mary of Renss., NY
Source: consumeraffairs.com

I purchased a GE Microwave Oven model # JES1139WL03 in late May of 2010. In
I purchased a GE Microwave Oven model # JES1139WL03 in late May of 2010. In early July, the paint started coming off the inside of the door when I wiped it with a damp dishcloth. I called Lowes, where I had purchased it, but was told that their warranty was only 30 days. I called GEs Consumer Support line and was told that for $65, I could ship the microwave to a repair center who would determine whether the machine could be repainted or would need to be replaced. I was told that either would require me to pay for it, since the machine still worked and peeling paint was not considered to be a warranty item. I guess if it catches fire, then they might warranty it.
Published: September 30, 2012
Mary of Coden, AL
Source: consumeraffairs.com

My GE dishwasher came with my new Miller & Smith house. Its 2 years old
My GE dishwasher came with my new Miller & Smith house. Its 2 years old. The bottom tray is rusting in several spots and you cant open the door while in operation to add an extra dish. When you open the door the dishwasher should pause while you add the dish, but this one continues working as if the door was closed and water sprays everywhere. I understand the one year warranty (they must know their products do not last long). Their support line tells me my options are to get it repaired ($99.95 for a tech to come and diagnose, then additional charges for parts and labor to install the parts on the next visit). The bottom tray is ~$125. I found their customer service rude, unsympathetic, and bothered by my questions. I was also told to go their website and review the rebate offers on a new dishwasher. I wanted to understand that program better, but the customer service agent did seemed uninterested to help me.I was quite surprised in getting this poor quality product and poor service from GE. Im not going to bother with repairs, because the cost at least $300, so I will opt to put that money in a different brand. I was considering giving GE another chance and taking them up on their rebate offer, but after reading all these other reviews, I certainly will not. The time I spent writing this will very likely have no impact on making GE change, but maybe put a tiny dent in their reputation and they will get one less sale from me.
Published: December 27, 2014
Al of Ashburn, VA
Source: consumeraffairs.com

I replaced a GE JEM25 microwave when the Magnetron gave up with a PEM31DWW
I replaced a GE JEM25 microwave when the Magnetron gave up with a PEM31DWW unit. Within 14 months the paint on the ceiling of the oven started flaking off. Contacted GE and they offered to sell me another oven for $166. After reading all the negative reviews on this site, I dont think I will ever buy another GE product.
Published: February 21, 2014
Rob of South Lake Tahoe, CA
Source: consumeraffairs.com

I purchased a GE Profile Microwave 2 1/2 years ago and now it is shooting s
I purchased a GE Profile Microwave 2 1/2 years ago and now it is shooting sparks out the back and making a loud noise. I have to admit that the microwave did work well and my mom even bought the same one because it was good. I never bought a GE appliance before because I was told they have a bad reputation. I thought the Profile Series would be better. Wrong!
Published: May 9, 2012
Stephanie of Center Valley, PA
Source: consumeraffairs.com

Wife started using the microwave. Within a minute she smelled something bur
Wife started using the microwave. Within a minute she smelled something burning. She opened the door and a flame shot out. Thankfully she remained at the microwave as it was running. Could have been catastrophic if the microwave continued to run for another minute. There is a charred 2 inch section at a circular piece in the inside top of the microwave.
Published: December 25, 2019
Raymond of Ridgewood, NY
Source: consumeraffairs.com

I purchased this product in June 2011 for a summer weekend getaway home. I
I purchased this product in June 2011 for a summer weekend getaway home. I used it 5 times during that summer. The following summer I didnt use it at all. Summer 2013, I used it and everything seemed fine. That night I heard something and the microwave turned on by itself! Thank goodness I was at the house. I cannot believe this unit has not been recalled yet, as I see other consumers are complaining about the same thing. I keep the unit unplugged all the time. What recourse do I have as a consumer? I have my bill of sale and paid good money for this unit.
Published: July 5, 2016
Gloria of Wantagh, NY
Source: consumeraffairs.com

I received a recall on my original wall oven with microwave unit, and was o
I received a recall on my original wall oven with microwave unit, and was only going to receive financial help from GE, if I replaced it with the same unit model JTP90. The unit was only 3 years old at the time. I purchased the new model, which cost $1,200.00, and received a check from GE for $600.00 for the recall, which is already a rip off in my opinion. I had the new unit for 14 months, when the microwave stopped working completely, with no power whatsoever. I thought it had blown a fuse. I took it to the repair center, and they tell me the diode, capacitor, and fuse have all failed. $200 later, it can be fixed, but they have no idea why all three went out at the same time. I, however, do know, GE just makes junk! I will never purchase another GE appliance. Just a side note, my 3 year old dishwasher was also recalled, and it was $600 to replace it with the same model. They sent me a check for $300. It sounds like GE has a good thing going. Make a piece of junk and recall it a few years later, and only give the customer half of the cost to replace it, and only if they buy another GE product! Wow!
Published: March 9, 2012
Sharmie of Adin, CA
Source: consumeraffairs.com

I have a 3 and a half year old GE Cafe Dishwasher which I paid over $1400 f
I have a 3 and a half year old GE Cafe Dishwasher which I paid over $1400 for and yesterday, when I ran it, I had a couple of cups melted when I opened it. This morning, I opened it to remove the remaining dishes. I closed the door to it and left for work. I did not run it again, just emptied it. My husband came home about an hour after I left to a house filled with smoke and the smell of melted plastic. He opened the dishwasher and found everything inside melted. The spinners, the silverware holder and all the plastic rack dividers were totally melted.Apparently, the heating element stuck on and overheated it. If he hadnt come home when he did, I believe our home would have caught fire. He said the whole kitchen was much hotter than the rest of the house. The service repair man said it cant be fixed because it got so hot it melted the seals in the motor. It was not a wiring problem with the house. It was a problem with the dishwasher itself. So now, I am out $1400 plus a house full of very toxic smelling smoke.
Published: May 8, 2012
Christy of Amarillo, TX
Source: consumeraffairs.com

GE Model JVM1540LM5CS - Fire inside microwave while making popcorn. Top cen
GE Model JVM1540LM5CS - Fire inside microwave while making popcorn. Top center piece, inside microwave, caught on fire. Was able to quickly contain the fire to the circular plastic cover which I removed. Called GE customer relations for service. The service technician that came to repair our microwave said he had just come from a customer with the same problem. Sounds like GE should take a close look at the plastic piece that catches fire and see about replacing it with one that wont burn.
Published: December 4, 2013
Jack of St. Augustine, FL
Source: consumeraffairs.com

My dishwasher is doing the same thing as the recalled models. The GE Cafe m
My dishwasher is doing the same thing as the recalled models. The GE Cafe model is not included in the recall. The dishwasher front, which is stainless steel, becomes so hot it burns to the touch and stays that way for hours. Burning smell in the kitchen! Cafe models need to be added to the recall!
Published: August 9, 2012
Patricia of Cobb Island, MD
Source: consumeraffairs.com

Purchased my first GE dishwasher 3 -4 years ago, it died, one month before
Purchased my first GE dishwasher 3 -4 years ago, it died, one month before the warranty ran out, they sent a repairman at no charge, acted like he did not know what he was doing, mumbled something about a part and left saying they would return with a part 2 weeks later he comes back and says that they cannot fix it and they sent me a replacement dishwasher free of charge, 13 months later and it died, So I bought a more expensive GE dishwasher thinking it would last, wrong, 15 months later and its dead, went to parts select and troubleshooted it, ordered all parts recommended to fix the issue and its still dead, these parts cost me 300, so I contacted GE to see what they had to say, no help at all except to only charge me for 50% of parts, I have to pay for house call and labor and installation, gee what a deal NOT bottom line, GE dishwashers are junk, dont buy them.
Published: October 28, 2019
Jeannette of Charlotte, NC
Source: consumeraffairs.com

Microwave and convection oven together...perfect for heating food or baking
Microwave and convection oven together...perfect for heating food or baking. Very easy to operate. G.E.profile. Mounts over the stove with an exhaust fan and lights. Also has a rotating plate in it to heat evenly.
Published: July 13, 2019
Harold of Yantis, TX
Source: consumeraffairs.com

My microwave is a GE, model JE 1040 made in 1998, which they probably dont
My microwave is a GE, model JE 1040 made in 1998, which they probably dont make anymore. I use it several times a week, mostly to heat up leftovers and water. Also pre-packaged microwavable meals, such as breakfasts and biscuits. I have cooked different kinds of meat and other items in it many times and am completely satisfied with it. I would be lost without it.
Published: December 14, 2015
Howard of Vermillion, SD
Source: consumeraffairs.com

Run, dont walk, toward any dishwasher other than a GE. Problems with the di
Run, dont walk, toward any dishwasher other than a GE. Problems with the dishwasher within one year - black residue on my dishes that felt and smeared like grease. Calls to GE repair resulted in the worst customer service I have ever experienced. One call returned at 4:00 am. After two visits, a lecture about how to load a dishwasher, I gave up. The effort of making calls for visits, taking time off work, rude repair technicians and being told it was not grease, I now have a dishwasher a few years old that is falling apart. Screws are now coming loose and the buttons are sticking.
Published: July 21, 2014
Toni of Lake Forest Park, WA
Source: consumeraffairs.com

I purchased my machine in 2019. The only concern I have with this machine i
I purchased my machine in 2019. The only concern I have with this machine is that I’m never sure of the amount of water that fills the tub with some features that I’m not used to. The tub on this machine enables me to wash very large loads including my queen size quilt. After washing, my clothes are practically dried which cuts down on my electric bill for the dryer. The drain and spin feature allows for a drier finish. Everything else is good. As long as you’re using the right soap the clothes are the cleanest.
Published: May 19, 2020
Cheryl of New York, NY
Source: consumeraffairs.com

I purchased a GE microwave and had 3 different problem with it. They sent a
I purchased a GE microwave and had 3 different problem with it. They sent a service man out and he could not fix the problems. Now GE said they are closing the case even though they know I do not feel the problem has been fix. My other GE microwave, I really liked until it stopped working around 8 yrs old. This one is a piece of junk. It is an over the stove microwave so I cannot just take it back to the store. I would say GE has really gone downhill over the yrs. This will be the last GE product I ever buy.
Published: November 23, 2015
Fern of Missoula, MT
Source: consumeraffairs.com

I love the GE. I bought a GE dual fuel range about 3 years ago when my 6 yr
I love the GE. I bought a GE dual fuel range about 3 years ago when my 6 yr old Frigidaire stove caught fire. Always wanted to cook with gas but have electric oven and broiler. It's also easy to clean the cooktop unlike older gas stoves. Love the big fast boiler eye.
Published: August 26, 2017
Marty of Durham, NC
Source: consumeraffairs.com

Periodically my GE Profile Dishwasher will not clean well. On every occasio
Periodically my GE Profile Dishwasher will not clean well. On every occasion it is due to clogging of spray ports on the upper and/or lower spray arms. Removing the blockages is nigh-on impossible as it is often not possible to extract the blockage from the outside and its not at all possible to flush the blockage back down the arm to extract it at the centre. All that is required is a bit of forethought and the creation of some access to the arm. I was frankly surprised to not be able to find a replacement arm as the suggested solution to this problem, the additional part revenue being part of GEs the business model. There are a number of other design issues with the assembly at the bottom that make me think it was done by an intern and nobody checked her work at the end of summer break before it went into production.
Published: September 2, 2015
Rupert of Richmond, BC
Source: consumeraffairs.com

We have a GE Advantium Microwave. It is our second model (we moved and left
We have a GE Advantium Microwave. It is our second model (we moved and left the first one behind). It is spacious, has an intuitive menu system, cooks extremely well, also includes a convection oven feature that we use to great advantage. The nicest microwave weve ever used (and weve used plenty of them).
Published: December 14, 2015
Fred of Louisville, KY
Source: consumeraffairs.com

GE continually shows us why they are failing as a company. In just this las
GE continually shows us why they are failing as a company. In just this last year I have replaced a less than 5 year old GE microwave, three separates parts to my GE monogram refrigerator, and now this one and a half year old dishwasher. The only appliance that GE makes that hasnt broken is the stove/oven that is over 10 years old and shows no signs of weakening.I purchased the upgraded stainless steel model that contained all the bells and whistles. It lasted 1 year and 3 months before the entire control panel stopped working. We utilized the dishwasher about once a week or once every two weeks in a two person household. Hardly a rough environment for a 700$ appliance. The repair costs was quoted for 99$ just to have GE look at it. The control panel was 140$, plus additional labor. This amounts to over 280$ to repair a year old product. I advise buying LG or Bosch.
Published: June 16, 2019
Bryan of Atlanta, GA
Source: consumeraffairs.com

We purchased a manufactured home that had brand new, GE appliances in it. W
We purchased a manufactured home that had brand new, GE appliances in it. We have been in the home for almost two years, but the dishwasher has never worked well, at ALL, even when it was brand new. We called GE and they sent a local appliance repairman to our house. He said that there was nothing wrong with the dishwasher. They are just junk. Amen! I have tried running the water in the sink until it is hot before the dishwasher fills up, we have tried using a citrus additive that is supposed to help it clean better, we have tried several different kinds of soap, NOTHING works. It never gets the dishes clean, there is always residue and food left at the bottom of the dishwasher, and it runs for hours on end. I cant wait until I can get rid of this pile of junk and purchase a Whirlpool or anything else. I will never purchase GE appliances, EVER!!!!
Published: February 27, 2015
Virginia of Dillon, MT
Source: consumeraffairs.com

GE DE68 00307A microwave was bought in June of 2011. Last weekend, August 2
GE DE68 00307A microwave was bought in June of 2011. Last weekend, August 25, I was heating water and the microwave started smoking and then failed. The entire apartment was filled with chemical smelling smoke. I have a parrot and had to get her out immediately as this type of smoke is highly toxic. I had to keep her out all night long.
Published: August 29, 2012
Gretchen of Minneapolis, MN
Source: consumeraffairs.com

I cant remember the exact date of purchase for my GE Spacemaker microwave o
I cant remember the exact date of purchase for my GE Spacemaker microwave oven. I have a receipt somewhere, but I have receipts for repair dated 2002. It is for a door seal gasket for the microwave. A model JVM60 GE Spacemaker installed over the range.The microwave worked perfectly for several years. Then one day, when I pressed the start button, I noticed a small fire inside the window above the control panel where the time is displayed. I called repair man; I was told that it was the circuit board, and GE was not able to send repair spare part. Since then the microwave is only good for displaying the time, and storing my everyday pan. I do remember paying $400.00 for this microwave because I purchased it at my employment. It would seem to me a company making a $400.00 appliance would be backed by a circuit board, which they know would go bad in a short time. Thats why they only had a one year warranty guarantee.To show you the difference in a microwave appliance, I purchased a small counter top microwave in 1997; it still works like a charm, and I use it every day. From the negative reviews I read on these Spacemaker microwaves, I firmly believe there should be some compensation to us consumers for the money spent, plus the hazards we experienced. If that is not agreed, then all of us consumers should file a class action suit against GE.
Published: July 22, 2011
Shirley of Alpine, CA
Source: consumeraffairs.com

I purchased a jes1451dn1bb microwave 16 months ago and I just noticed the e
I purchased a jes1451dn1bb microwave 16 months ago and I just noticed the enamel coating on the top of the unit is chipping. GE has been unhelpful, saying it is outside the warranty and I need to mail the cord and sticker inside it to have a rebate issued. Since I use my microwave daily, I cannot wait until it is processed to buy a new unit. Not only did the product endanger us with exposing our food to paint emissions, the company has been unhelpful. I highly recommend buying another companys product and do your research!
Published: November 15, 2011
Tracy of Shaker Heights, OH
Source: consumeraffairs.com

July 4th, 2010 - GE Profile Dishwasher, Model: PDW9200N00BB, Dishwasher had
July 4th, 2010 - GE Profile Dishwasher, Model: PDW9200N00BB, Dishwasher had been humming after cycle was over for a little while, this night I walk into the kitchen late and find it full of smoke. Circuit board has a hole burned though it and wiring harness is melted. Never tripped any safety, could close the door and it would come right back on, smoke and all. This model was not on the recall list but I called GE anyway. After describing the fire they send someone out, then they send a new dishwasher out and install it. I assume they wanted the old one to look over or just to get rid of it. New washer installed the end of July 2010, new model number PDWT500R10BB. Today is 2012-02-02 and the new machine would not stop at end of cycle (Got down to 1 minute and stay there for at least 20 minutes before we turned it off). This machine is now making the continuous hum after the cycle stops that the old one did before it caught on fire.Called GE, they said they could maybe go half on parts and service until they checked where I was located. (Wichita, KS. Area population 500,000+) They said that they didnt send factory techs to my area and I would need to contact a local repair service. I pointed out that they had a factory guy for when my machine was on fire and they said it was just a malfunction now, so they could not. No half on the price for repair either at this point. This is a $1100 to $1200 dishwasher with, as near as I can tell from complaints online, a history of going up in flames. I understand things break etc, but when you continue to put out products like this and then refuse to remedy the problem, I and anyone who will listened to me will never own anything GE again.
Published: February 2, 2012
Gregg of Wichita, KS
Source: consumeraffairs.com

GE Microwave Model JES1655DR1BB - I have had many microwaves over many year
GE Microwave Model JES1655DR1BB - I have had many microwaves over many years but never had one malfunction as bad as this one. I am only glad that it happened with me rather than my wife or child. Or, if I had left the room while it was on. Immediately after turning the unit on, it started making loud electrical arcing noises and flashing light. I had just placed a microwave safe glass dish inside. I removed that and tested again with nothing inside. Same thing happened. I next thoroughly cleaned the unit. Tried again. Same thing happened. I had paid a little more for this unit than the usual believing it would be worth it. It clearly was not.
Published: June 15, 2014
Greg of Dexter, ME
Source: consumeraffairs.com

Not very satisfied with the functionality. Turntable does not work or has e
Not very satisfied with the functionality. Turntable does not work or has ever worked. Time features and power adjustments are not very intuitive. I would not recommend this brand, I believe there are other brands out there are much better for the same price range.
Published: January 17, 2017
Joseph of Escondido, CA
Source: consumeraffairs.com

We have never had a problem with the microwave. Most of our use has been he
We have never had a problem with the microwave. Most of our use has been heating things up. There has been a few times that our granddaughter made something else. It is lightweight. Easy to clean. Not too large or small. Fits what we use it for perfectly. Doesnt take up much room. It heats perfectly. It has been a really good microwave.
Published: July 6, 2019
Natalie of Palm Bay, Florida
Source: consumeraffairs.com

I bought a GE Profile dishwasher 3 years ago. After two weeks it was broken
I bought a GE Profile dishwasher 3 years ago. After two weeks it was broken. I called Mabe Appliances and they sent out a tech. He told me it was broken. When I called Mabe back the service people told me to read the manual...yes really. Finally after a lot arguing they replaced it. About a day after the 1 year warranty expired all but one of the cycles stopped working. I have to take it apart every 3 months to clean out the water output as its clogged and the water doesnt have any pressure and therefore does not clean the dishes. I got up this morning and the dishwasher was still running but there were no lights on the front of the unit. I turned it on around 8pm so it was running for 11 hours. When I opened the door it was apparent it had been stuck in the wash cycle the whole time. It is now completely dead. Nothing works. No lights. WHAT a piece of JUNK. How can GE put their name this crap? STAY AWAY FROM GE APPLIANCES. Spend a little more and get a Samsung or LG or Bosch.
Published: June 13, 2015
Bob of Mississauga, ON
Source: consumeraffairs.com

My 3 year old $600 GE micro caught on fire with nothing it. I set the timer
My 3 year old $600 GE micro caught on fire with nothing it. I set the timer on my top of the line GE microwave for a reminder. Nothing in the micro, cooking nothing! When I came back it was on fire! Melted the inside. If I would not of been there it would of burnt my house down! The only way to shut it off and put out the fire was to turn off the power to it. The next day as soon as I turned the power on my GE microwave started on fire again!!! This must be happing to many people and needs to be addressed by GE! This company needs to be held accountable for burning houses down!
Published: August 1, 2018
Bryan of Mountlake Terrace, WA
Source: consumeraffairs.com

Dishwasher has been running 3 hours and it still has not finished. It is th
Dishwasher has been running 3 hours and it still has not finished. It is the loudest dish washer I have ever owned and this is the 5th house I have owned. To top it off I just paid $270.00 for a GE professional to come to our house to troubleshoot our problems and it fix the issues. Guess what, problem not fixed and GE has my hard earned money. Thanks, GE.
Published: February 2, 2012
Frank of Cypress, TX
Source: consumeraffairs.com

My microwave on the inside paint start peeling off. I have this appliance 2
My microwave on the inside paint start peeling off. I have this appliance 2 years, it has slowly been peeling since that time and now it has completely peeled and rusted on the inside. This WAS a gift. The outside looks great, the inside is so bad. The serial # is LT914637B model JES1451DN1BB manufactured in 2010, Made in Malaysia. Be Louisville ky 40225. Does the united States make anything except make us pay taxes. This is a piece of mess. The last 2 years my husband he suffered with LLC. Now I got to deal with this. Poor workmanship. I want GE to give me my money for the MW or total replace it. Rate 0.
Published: June 25, 2014
sam of Jax, FL
Source: consumeraffairs.com

We built a new home in 8/19. Much to our dismay, the builder only offered G
We built a new home in 8/19. Much to our dismay, the builder only offered GE appliances. We had a bad experience with a GE appliance in the past so we went with the most expensive offered, the Profile series. Nine months into our new home, the microwave push button to open the door broke (with food stuck inside). I was only able to schedule an appointment through an automated system. Days later, repairman breaks door trying to get food out. Parts were ordered and new date was set for one week later. Day before that appointment, I got a call canceling my appointment due to the part being on backorder. The entire call took 57 minutes. New appointment was set for an additional week. Again, appointment canceled and part was ordered from third party. Third appointment was a repeat yet again (but without a call and with repairman showing up). The rep did say she would send $70 for us to buy a small microwave while waiting. We are now at three weeks without our microwave being fixed and I have spent HOURS on hold trying to get to a resolution. Last representative asked why I even made an appointment if I didnt have the parts. What!! They have scheduled the appointments. I asked to talk to a supervisor but then was told it would be 24-48 hours before someone could call me back. The rep said this is the timeframe they quote for a callback but she didnt know when anyone would actually call. No idea how much longer we will have to wait-it seems we are at their mercy. When buying new appliances in the future, we will ask who services their warranty! Either way, we will never buy GE appliances again.
Published: June 16, 2020
Donna of Round Rock, TX
Source: consumeraffairs.com

I have owned my dishwasher for 5 years. Monthly, I use dishwasher magic to
I have owned my dishwasher for 5 years. Monthly, I use dishwasher magic to clean the inside, removing lime, minerals, rust and grease. The lower rack, under the silverware rack is completely rusted. I have used and owned dishwashers for over 35 years and not once has one rusted like this. Poor quality for the racks! I feel it should be replaced free of charge.
Published: February 29, 2012
Jody of Sioux Falls, SD
Source: consumeraffairs.com

Have been using dishwasher (PDWT380VOOSS) since May 2013. Dishes do not com
Have been using dishwasher (PDWT380VOOSS) since May 2013. Dishes do not come clean and I rewash by hand... have followed all suggestions by consumer relations, service technician and manual…cant afford to replace appliance…GE willing to replace at an aggressive discount because the appliance is working as it was designed to…disappointed in performance of a profile appliance.
Published: October 19, 2013
M of Yardley, PA
Source: consumeraffairs.com

The microwave is over the stove with a vent. It is about an 1100 w microwav
The microwave is over the stove with a vent. It is about an 1100 w microwave. I just have to eat out a little bit more time here are the ones that are bigger. The price was right there and that I would’ve bought something else.
Published: July 13, 2019
Frederick of Hey, Florida
Source: consumeraffairs.com

Built our house and had new GE Appliances. Oven is a GE Profile and the com
Built our house and had new GE Appliances. Oven is a GE Profile and the computer panel went out twice in the first 2 yrs. The profile microwave model PEB 7226 SF1SS IS NOW ONLY 3yrs old and not functioning. We rarely use the microwave. Will never buy GE anything in the future.
Published: June 22, 2017
Holly of La Vernia, TX
Source: consumeraffairs.com

I am writing this more as an educational notice for consumers of the G.E./R
I am writing this more as an educational notice for consumers of the G.E./Rheem gas water heaters to aid in uninterrupted service and understanding of the water heater. Installation locations: If you have installed your unit outside, all though in the owner’s manual, it states that G.E./Rheem says to never install the unit outside. People that live in warm climates do have their unit installed as such, but in a metal enclosure, of which to the city codes are fine, but again not by the G.E./Rheem standards. So being as this is accepted by city codes, people do and will continue to install water heater outside in enclosures.
Published: March 11, 2015
M. of Burbank, CA
Source: consumeraffairs.com

I rarely use it. I know to avoid too close to the signals produced in the m
I rarely use it. I know to avoid too close to the signals produced in the microwave and use it only about once a month.
Published: December 14, 2015
Marvin of St. Joseph, Michigan
Source: consumeraffairs.com

Clean neat appearance over stove. Fast consistent heating. Easy heating opt
Clean neat appearance over stove. Fast consistent heating. Easy heating options. Turntable on or off. Also, love the stove top light. Cost a bit more than I thought it would, but not much more than others.
Published: July 19, 2019
Wayne of Rocky Mount, North Carolina Area, NC
Source: consumeraffairs.com

28 Inch Front Load Washer with 4.9 cu. ft. Capacity, 13 Wash Cycles, 1250 R
28 Inch Front Load Washer with 4.9 cu. ft. Capacity, 13 Wash Cycles, 1250 RPM, Steam Cycle, Steam Assist, Time Saver Option, Sanitize Cycle, Energy Star in White. Overall this machine is top of the line. Purchasing a home appliance is like purchasing a vehicle. I took my time and reviewed and compared before purchasing. About 3 months. I had just purchased a home and so you want an appliance that is going to last. It has a 10 year warranty. It has 3 color options. It's cosmetically attractive. It also is elevated which is a smart choice for a basement machine in case you have issues with water in your basement.
Published: May 23, 2020
Jennifer of Warren, MI
Source: consumeraffairs.com

Have owned, installed, and repaired many dishwashers throughout the years a
Have owned, installed, and repaired many dishwashers throughout the years at various houses. This GE unit is by far worst dishwasher that I have ever had the displeasure to install and operate, and it replaces a Kitchen Aid unit that started a fire, see **. Specifically the GE unit had the control panel break off due to misalignment, requiring repair, the drain bulkhead fitting was poorly designed and caused a leak, requiring repair, the water solenoid valve failed in the 2nd year, and finally the door does not lock closed without significant care and attention to alignment and requires many attempts to lock closed for the start of cycle. This is the worst and I cant wait to pull it out and replace it.
Published: March 12, 2020
Luke of Norristown, Pennsylvania
Source: consumeraffairs.com

Since 2010, our 2006 GE 1.1 cu. ft. countertop microwave oven model # JES11
Since 2010, our 2006 GE 1.1 cu. ft. countertop microwave oven model # JES1136WL has had power failure problems. It began in our previous home and now in our next home. All of a sudden, Id check the panel and it would say PF, which means power failure. So, Id reset the clock and there it is, ready for the next usage. Over a year later, in our new home, as of yesterday, it will start and immediately cut off. Now, weve been using this microwave in the same plug since May and now its October. So, what happened? Today, Im looking for the users manual and have located it online. But it appears that the PDF GE has for it, the Adobe document, has a problem. So, Im going to check it on my laptop, as this is my PC. Thank God we only paid under $100 for it. On some of these consumer complaint stories, the person paid a great deal for theirs.
Published: October 17, 2011
Carolyn of Columbus, OH
Source: consumeraffairs.com

Dont buy one. I bought two last year. The first one completely died before
Dont buy one. I bought two last year. The first one completely died before the 60 days were up. I took it back to Sams club and bought another. The tag inside says it was made February 2011, so its only a year and a half old. Under the carousel, the paint is peeling big time. I wrote GE repeatedly, asking if it was still ok to use it. After ignoring me for quite some time, I got this reply. In the notice, they told me to get Sams club to replace the defective and apparently unusable product they are selling knowing it is defective. I love the part where you cant cook something with too much liquid in it. Who does that when they microwave?Heres what they said: Thank you for contacting GE regarding your microwaves and the paint peeling issue. I did some research on it and found that it a common issue among all brands. Excessive heating of un-covered liquids can create a high amount of condensation that the inside paint is not meant to withstand. Minor chips to the coating on the microwaves interior cavity will not affect the products performance. However, if the coating is actively flaking or peeling anywhere inside the oven cavity (including under the turntable), discontinue the use of the microwave and replace it. GE does not have an approved method of repair, and the microwave is not repairable. Please return to Sams club for an exchange, if you are still within the one year warranty. If Sams is refusing to accept the return, contact the Sams Club Support Team at 1-877-885-2787. GE will then reimburse Sams club.
Published: July 20, 2012
J of Garden City, KS
Source: consumeraffairs.com

Ive had a GE Dishwasher for over 6 years and it works great. The issue is e
Ive had a GE Dishwasher for over 6 years and it works great. The issue is every 2 years or so, the plastic over the metal rods that make up the plate racks wear away and rust the underlying metal. The first time GE charged me about 200.00 for the racks, where the dishwasher only cost 250.00. The second time they replaced for free and now this third time, GE is being absolutely absurd not replacing these racks. My concern for mine is the health issues arising from having rusted parts in the washer. I believe this to be a manufacturers defect and could be happening in 1000s of these dishwashers. Metal should not go into water!!! GE should gladly replace my racks but theyre giving me a major problem, like take our offer or dont bother us. Please see the attached pictures and hopefully this doesnt happen to your dishwashers.
Published: June 5, 2014
robert of Miami, FL
Source: consumeraffairs.com

I thought there were food particles between the glass plate and the ring. W
I thought there were food particles between the glass plate and the ring. When I took out the plate, I saw that the paint had bubbled and was peeling off the bottom of the microwave. Extremely unhappy with this. Ive had hand-me-down off brand microwaves that lasted much long than this GE and with NO PROBLEMS until they just rolled over and died. I have all GE appliances in my kitchen and have to say that Ill never buy GE again. Electric stove is a problem, dishwasher a problem. Refrigerator was a problem (when it was new! it was fixed and thankfully is still running well).
Published: July 30, 2014
Jackie of Somerset, NJ
Source: consumeraffairs.com

From these posts, Ive seen people saying that they couldnt trust GE America
From these posts, Ive seen people saying that they couldnt trust GE American-made anymore. Our microwave oven was made in Malaysia, but GEs home office appears to be in Louisville, Kentucky. Our problem: peeling paint on the door and upper part of our 2009 GE #JES1451DN1WW oven. As a cancer survivor of 8 years, my antenna goes up with any defaults such as this. On a common sense scale this should never be happening. I was very sad to see no recalls on these items Ive been reading about and am frankly scared to use this microwave. Shame on you, GE.
Published: November 24, 2012
Dianne of Washington, Nc, NC
Source: consumeraffairs.com

I purchased a GE dishwasher on March 15th 2018... The first dishwasher I re
I purchased a GE dishwasher on March 15th 2018... The first dishwasher I received on March 23rd was obviously broken. The dishwasher setting piece was completely broken off and the sides were dented and looked like it had been dropped. Ok. The delivery guys immediately called it in and reordered another one for me. A week later the second dishwasher came, it looked fine from the outside so I signed for it. Once I opened it I saw that the top rack was missing wheels and the second shelf wasnt even connected to the dishwasher. I called and a week later they came and got it and left a new one. I asked the delivery guys to unpackage it and look inside. Immediately the top arm cycle fell off and the HE symbol at the bottom popped out. They assured me that was normal... When the install guy arrived a week later he said he thought everything looked ok. He ran a cycle, then left. Before he was out of my driveway the cycle arm/water sprayer fell off and water sprayed everywhere... I brought the piece into Home Depot and they told me it was broken (duh) and they would order a new one. NO. This was going to be the fourth time I will be taking off work to deal with this dishwasher! GE is absolutely gone down. The products being produced are either being sabotaged by the employees from the Ohio plant, who are all losing their jobs because the plant is about to get shut down and is going to be moved to Mexico or GE is absolutely horrible at business, design and producing quality appliances.Regardless, I will NEVER purchase a GE product again and would never recommend to anyone to purchase a GE appliance! I am going to get a refund and insist compensation and inconvenience fees! I had to take off work 4 Times, had to cancel plumbers 3 times (still was charged). I lost money from my work, time from life and a month without a dishwasher. Also, a month with a broken one sitting in my living room because they wouldnt come get the 2nd and 3rd broken dishwashers until a I ordered another one and had that one delivered before they got the broke one(s) out of my house. I had broken dishwashers sitting in my living room for a month. Easter was quite embarrassing with an appliance next to the table to say the least. DO NOT PURCHASE GE APPLIANCES!!!
Published: April 13, 2018
OLIVIA of Huntsville, AL
Source: consumeraffairs.com

Ive had my microwave for 12 years. Ive never had any problems with the micr
Ive had my microwave for 12 years. Ive never had any problems with the microwave since its purchase and very pleased. I dont plan on replacing until the microwave would stop operating or not pleasing in the kitchen.
Published: December 14, 2015
Phillip of Keedysville, MD
Source: consumeraffairs.com

While the microwave works fine, as far as microwaves go; it does heat uneve
While the microwave works fine, as far as microwaves go; it does heat unevenly but eventually gets the job done, the interior is cracked and shows signs of rust and deterioration. I dont remember ever seeing this on in previously owned microwaves. I would only use it for basic heating and reheating.
Published: December 27, 2020
T of Basking Ridge, NJ
Source: consumeraffairs.com

I had to place a new order for a trim kit for my new microwave oven since t
I had to place a new order for a trim kit for my new microwave oven since the original one did not fit. I was told it would be 5 days when I placed the order, then it was backordered for 5 days, then 7 more days and now 3 more days. When will I receive the product that I have paid for 3 weeks ago?
Published: March 12, 2015
Wiley of Mckinney, TX
Source: consumeraffairs.com

I bought this dishwasher GLDT690TBB-00 on 05/12. Its not even 2 yrs old. I
I bought this dishwasher GLDT690TBB-00 on 05/12. Its not even 2 yrs old. I had some minor complaints about how hard it was to fit bowls, how the utensil rack wasnt easily accessible, how long the cycles took, how it had to be vented right after a cycle to keep clean dishes from smelling musty... But I was willing to put up with that. I spent about $700 new. The dishes did come out clean, if I stacked them properly. I only used it when full, about 2x/week, as I am an aging widow & live alone. It stopped functioning a few days ago. Control panel lit up, a little water came in, but no action with spray, etc. Called a local repair company today. They say the control panel is shorted out, and that in turn burned out the motor. The repair cost would have been $524.61. REALLY? Not doing that! Very disgusted. Ill never buy GE again. Last KitchenAid lasted 12 yrs, but as all the repair guys say: They dont make em like they used to! Too many bells & whistles. All I require is clean dishes, and for the appliance to do its job.
Published: April 15, 2014
Eunice of Douglasville, GA
Source: consumeraffairs.com

The microwave is small enough for 1 person and yet big enough for a family
The microwave is small enough for 1 person and yet big enough for a family of 4. I feel it cleans up pretty easily also, inside and out. This is also a stainless steel on the outside, that makes it easy to clean.
Published: July 10, 2019
Joann of Iowa City, IA
Source: consumeraffairs.com

The jvm3160 series has a known defect in the door interlock electrical syst
The jvm3160 series has a known defect in the door interlock electrical system that blows the unit fuse if the door is opened while the mw oven is operating. This usually occurs after the warranty expires. Cost to repair can exceed the original cost of the unit. Mine failed in warranty but it took them 10 weeks to fix it. The reason it took so long is that GEs repair protocol calls replacing the whole door (which has NO electrical parts in it) instead of replacing just the latch assembly because the labor cost to replace the latch itself exceeds the cost of a complete door assembly. Door assemblies were on back-order because of the high failure rate.
Published: May 24, 2019
Doug of Granada Hills, CA
Source: consumeraffairs.com

GE profile microwave magnetron burned out after 2 years. Part is supposed t
GE profile microwave magnetron burned out after 2 years. Part is supposed to be under warranty, but repair is not. There are no service centers in my area. GE wont just send me the part, or let me send them my old part.
Published: July 29, 2011
Steve of Bayfield, CO
Source: consumeraffairs.com

Purchased a GE profile dishwasher two years ago. It stopped draining. After
Purchased a GE profile dishwasher two years ago. It stopped draining. After 4 service calls and $400 we had to buy a new dishwasher. Basically I threw $1000 down the drain. My recommendation is do not buy a GE dishwasher!!!
Published: February 8, 2019
Elizabeth of Duxbury, MA
Source: consumeraffairs.com

My GE Profile Dishwasher was serviced 2 years ago for a faulty electronic c
My GE Profile Dishwasher was serviced 2 years ago for a faulty electronic control pad. It made starting the dishwasher a complete gamble, you never knew when it would actually turn on. I paid a couple hundred dollars to fix this problem 2 years ago and of course it has stopped working once again. So frustrating! GE decides to replace one bad part for another bad part. I then asked for the service call to be covered since it was obviously the same problem but they refused. So, GE am I to keep paying $89 for service fees so that you can keep replacing one faulty part for another? STAND BY YOUR PRODUCT!
Published: February 19, 2015
Vincent of Clayton, NC
Source: consumeraffairs.com

Purchased this dishwasher March of 2015. We have had at least five service
Purchased this dishwasher March of 2015. We have had at least five service calls because it does not clean the dishes. Glasses with just water in them when they went in the dishwasher come out dirtier than they went in. Residue is worse on the glasses, but other dishes are not getting completely cleaned. Forget it if something is stuck on, if you dont prewash, you are washing them again. GE has replaced numerous pieces, blamed our water was too hard until they found out we had a water softener and water system and then blamed that instead. We have changed soaps (five different brands), tried every setting in multiple ways, turned off the water system and just had the water softener run, turned everything off and nothing improves the quality of the clean. GE has even refused to pay the service technicians that they GE sent out to repair the dishwasher. Now we cant get anyone to come look at it because they are afraid they wont get paid. We have had three dishwashers prior to this one and have never had an issue with the dishes coming clean. We have maintained that there is not enough water pressure to rinse the dishes, but they are adamant this is not the case. Regardless, the dishes are still not coming clean. All we want is for it to be fixed, replaced or our money refunded. GE customer service is terrible.
Published: March 3, 2016
Susan of Wenona, IL
Source: consumeraffairs.com

GE over the range microwave Model hvm1750DM1 WW - It’s just about 2 years
GE over the range microwave Model hvm1750DM1 WW - It’s just about 2 years old. It started making a grinding noise, then quit. No more GE for me.
Published: June 9, 2013
Barb of Chandler, AZ
Source: consumeraffairs.com

Their service department is absolutely terrible. The motherboard went out a
Their service department is absolutely terrible. The motherboard went out after only 8 months of use. They never notified the appliance repair company that the part was back ordered (I had to follow-up on that) and every step of the way I kept being told someone will follow-up in 2-3 business days. No one ever followed up with me, I had to call to check on the status of my claim EVERY time. The request for a replacement dishwasher after two weeks was denied because the part was going to be available in another week, but then I wouldnt receive the part for a minimum of another week after that. When I asked to speak to a superior she refused and told me no one was available. After demanding to speak to one I was told they would contact me in ANOTHER 2-3 business days (well see if that ever happens). This is (still going on) an absolutely awful service experience. I dont care that the dishwasher broke, I care that theyve handled it so poorly.
Published: June 27, 2018
Melanie of Bakersfield, CA
Source: consumeraffairs.com

My GE microwave is the Advantium version which’s heats to a 1000 degrees.
My GE microwave is the Advantium version which’s heats to a 1000 degrees. In fact, today the 4th of July I will be using it instead of the BBQ. I have baked, broiled, heated and other things in this unit. This is my 2nd one over the years and I enjoy it immensely.
Published: July 15, 2019
Bernard of San Dimas, CA
Source: consumeraffairs.com

We have had this microwave GE JVM1631wb007 (2003) for a number of years ins
We have had this microwave GE JVM1631wb007 (2003) for a number of years installed above our stove. It was given to us by my husbands son so we did not have it registered with GE as owning it. However, I just sent an email to GE today asking for help as I find absolutely nothing on the internet about a scorched outside microwave door. We have had no issues with it whatsoever - until now. When we returned home from a one week vacation this past Sunday evening, we came home to a scorched OUTSIDE door on this microwave! The inside is fine. The two people who came into the house while we were gone said they did not use it but it is DEFINITELY scorched around the entire area on the outside around the screen area. I refuse to use it although my husband (who is an appliance repairman but does NOT work on microwaves) says its fine to use. Its not only hideous, it LOOKS unsafe to use. Im scared its going to catch on fire but my husband says dont worry and go ahead and use it! Im attaching a pic of it... Anyone else heard of this? Its not like we dont have the money to replace it. Im NOT going to touch the thing... You cant tell him anything. He thinks its fine. I need PROOF that this is dangerous to convince him... Please help before the house burns down!
Published: May 28, 2016
Gina of Olathe, KS
Source: consumeraffairs.com

Generally ok, but the entire wash cycles take way too long. Certainly much
Generally ok, but the entire wash cycles take way too long. Certainly much longer than the older models. I guess thats more or less the case with most dishwashers today. It makes me hesitant to use the dishwasher when I consider all the energy it takes to function. I would prefer having a setting for speedier rinse/wash of just a few dishes.
Published: March 12, 2020
Wesley of Coppell, TX
Source: consumeraffairs.com

GE microwave model JES1344ES. This is a stainless steel with black accent 1
GE microwave model JES1344ES. This is a stainless steel with black accent 1.34 cubic foot microwave oven. It looks great. The micro is heavy for its size. The stainless steel is brushed and low luster finish. The door handle is chrome as is some of the other accent pieces. The push button panel is easy to read and has a large knob for making manual time adjustments. The light inside is very bright. There is a rotating platter in the oven compartment that is not knocked off of its guide rollers very easy. The push button panel is a glossy black material that is easy to attract fingerprints. The preset times that are programmed in the microwave is the only part of the product that could be an issue. For example the popcorn button when used has burnt all of the different brands of microwave popcorn that we have tried. It is set about 30 seconds too long. There is no way to adjust the preset time that I can figure out. We set the time with the large knob manually and the popcorn comes out just fine. The preset times for the Auto Defrost are also a bit off. They are not long enough. We also have a Subzero freezer set at minus 20 degrees Fahrenheit so that may be too cold for the defrost presets. Overall the microwave is great except for the preset times that Ive mentioned. We use it daily and have done so for five years. It still looks excellent inside and out.
Published: December 14, 2015
Joseph of Wyandotte, MI
Source: consumeraffairs.com

This GE Model JNM1541 is a 1500 watt, under counter microwave with quite a
This GE Model JNM1541 is a 1500 watt, under counter microwave with quite a few features. It has plenty of cooking power and has not failed in its nearly 5 years of use. I have never used the included metal shelf.
Published: July 21, 2019
Warren of Pleasanton, CA
Source: consumeraffairs.com

GE Model PDW9280J10SS Fire - Many GE Profile dishwashers have been recalled
GE Model PDW9280J10SS Fire - Many GE Profile dishwashers have been recalled during the same time frame as the model we purchased, but it is not listed as one of the recall models. Just as many other complaints, ours started to smoke out of the top of the front door and filled our house with smoke. Thank God we were there to shut it off. The next day I opened up the front door to see what had been burning and it had holes burnt in front and back of the main circuit box (for lack of better name), one burn mark right where the main wire harness plugs in and burnt right through it. This is the same description many others have written. There is a problem with all of these Profile dishwashers purchased between 2006 and 2009 (ours 2007). If we had not been home, who knows what would have happened?
Published: January 6, 2013
Kevin of Seattle, WA
Source: consumeraffairs.com

Our washing machine has been with us for almost ten years and I really love
Our washing machine has been with us for almost ten years and I really love the features which make it look modern and easy to dump in a load when we're running late for something. It has been having problems recently but it still runs okay, with only a few hiccups but for a little over ten years, that's pretty good!
Published: May 24, 2020
Rowan of Baltimore, MD
Source: consumeraffairs.com

In 2008 I redid the entire kitchen and purchased all GE Profile stainless s
In 2008 I redid the entire kitchen and purchased all GE Profile stainless steel appliances thinking I was purchasing quality items. Well, it didnt take long before the dishwasher broke but it was fixed for free by GE under a recall. However, now the refrigerator has begun to leak under the right corner of the ice/water dispenser located on exterior of freezer door and the microwave touchpad has also failed as I need to press below the actual keys for it to work half the time. When I spoke with GE customer service they basically told me there was nothing they could do with the refrigerator, I would have to call a repairman and have it looked at or pay their $100 diagnosis fee.The microwave they told me had issues with that particular touchpad and had it broken within first 5 years they would have repaired it for free under their recall program. But since its 7 1/2 years old I would have to buy the touchpad which normally only lasts for 6 months to 1 year or buy a new GE microwave and they would offer a rebate. Im so unhappy with their customer service and poor reliability of their products that Ive passed on each offer as I dont want to contribute another penny to a company that in my opinion is unethical and has horrible reliability. 3 out of 4 of my fancy GE Profile stainless appliances have broken! Thats a 75% failure rate! No thanks, Ill buy elsewhere. No wonder they cant sell their appliance business and why the stock hasnt moved in years... Wake Up GE, do whats right for your customers!
Published: February 19, 2016
Carlos of Miami, FL
Source: consumeraffairs.com

June 18, 2018 GE Spacesaver Microwave in use when there was a loud pop, hea
June 18, 2018 GE Spacesaver Microwave in use when there was a loud pop, heavy smoke boiled out of the unit and strong smells of wires burning was noted. On fixed income now what do I do? Understand my microwave has been reviewed by ConsumerAffairs for the same issue in the past. Whatever became of their investigation?
Published: June 19, 2018
Tanya of Granite Falls, NC
Source: consumeraffairs.com

Our microwave is of poor quality. Unit failed completely after a couple of
Our microwave is of poor quality. Unit failed completely after a couple of years in use, like many GE products. This GE unit had a large rotating platter and easy controls, but it just stopped operating one day. Nothing could get it going again, so we replaced it with a Samsung microwave which appears to function well (only a year into use, so no way to know yet) although platter is smaller and controls not as convenient.
Published: January 22, 2017
Norman of Silver Spring, Maryland
Source: consumeraffairs.com

We bought a new house with GE microwave, oven and dishwasher. Our fridge do
We bought a new house with GE microwave, oven and dishwasher. Our fridge doesnt give any water anymore and our touch screen microwave stopped responding to any touch. When I called customer service to come see, they want to charge $80 just to tell you whats the problem. GE has the worst appliances. I will not recommend it. I will go with Whirlpool brand.
Published: December 9, 2012
John of Cary, NC
Source: consumeraffairs.com

We bought this microwave (GE DE68-00307A) brand new 2 years ago and the pai
We bought this microwave (GE DE68-00307A) brand new 2 years ago and the paint is peeling off everywhere!!!! I keep my microwaves extremely clean, and this was not due to wear and tear by any means. I would say it started after about a year and a half of having it. I have showed multiple people and I cannot believe this is not on a recall list. This is extremely dangerous and could cause many issues. I am hoping someone can do something about this manufacturer and this product. This alone will make me never buy a GE product again.
Published: July 17, 2014
Kelly of Murfreesboro, TN
Source: consumeraffairs.com

I bought GE OTR microwave in December. It is exactly one month old now. My
I bought GE OTR microwave in December. It is exactly one month old now. My model no. is: 9195SVC. It looks good, but I find the fan very noisy, even when it is at low. My range hood which we had in the kitchen prior to this microwave was very quiet at low and only a bit noisy at high. I do not know if the noise is because I have steel exhaust pipes vented out. Rest is O.K. but given that others have reported problems in 1-2 months, I am still nervous.I bought this product at Sears with an extended warranty, which is some relief. However, when I was shopping for this at Home Depot, the salesperson told me these microwaves last only 4-5 years. One good thing about Sears extended warranty is that if it is not used over the five years, they refund the warranty payment (with taxes) in the form of a gift card and they were also cheaper than Home Depot.
Published: January 17, 2015
Ather of Halifax, NS
Source: consumeraffairs.com

We bought a brand new GE dishwasher from our local hardware store on Black
We bought a brand new GE dishwasher from our local hardware store on Black Friday. It was $600 dishwasher on sale. It was installed on December 5th, it broke on December 6th, and we had a repair man come out to take a look at it. To be fair, the local hardware store did ask if we wanted to replace (2 week wait time) or repair (2 day wait time) it. Since it was a bolt that was severed (by opening the door to the machine, mind you), we figured it would be an easy fix. The first technician who visited said, Yeah, its broken. I have to order a new bolt and then come back out in a week to fix it. And oh, by the way, Ill have to drill a new hole for it too. Thats when I called GE customer service to request a new product. But since my 48 hour window had passed, and we opted to have it fixed, it was keep it or ask our local hardware store to replace it at their expense. I bit the bullet and just had it repaired. Now, less than 2 months later, the technician has been at our house three times. He’s soon to have a fourth visit because we need a new dispense modulator. After speaking with customer service several more times, and with a not very nice lady in the Chairmans office, I still have a defective product. Oh, did I mention that Im paid hourly and have now taken off 13 hours? So what’s the use of that $600 dishwasher that we bought? Its been out of commission for more than 2 weeks, in less than 2 months, and has now cost us $900. Thanks, GE! We’re so glad to see you stand behind your product.
Published: February 5, 2013
Miranda of Cranberry Twp, PA
Source: consumeraffairs.com

We recently purchased three GE Profile stainless steel appliances for our n
We recently purchased three GE Profile stainless steel appliances for our new home. The total was somewhere around $3500. Within two weeks our $1000 dishwasher would not work. It took FOUR service calls and THREE weeks for it to finally be repaired. Now our $2000 oven (traditional/convection) has stopped working and the oven light will not go off without us tripping the breaker. Service tech not available for 5 days. I am expecting the new micro to go out any day now. All of these appliances are less than two months old. We had GE builder grade appliances in our previous home that are still running strong after 16 years. That is the reason we went with GE again. However, after the above mentioned issues with our new GE appliances, I encourage anybody who reads this to NEVER, EVER BUY ANY GE PRODUCTS AGAIN.
Published: July 12, 2016
Christy of Mckinney, TX
Source: consumeraffairs.com

We wrote to GE regarding the issue with the dishwasher and, after some phon
We wrote to GE regarding the issue with the dishwasher and, after some phone tag, a certified GE engineer came to the house, diagnosed the problem and ordered all the replacement parts. This morning, they came by to install and essentially rebuild the entire system with the exception of the stainless steel. Overall, we are very happy with the outcome. With all the negative issues GE experiences online with regard to the Cafe Series, I give them a solid 8 for responsiveness and taking care of the situation. Perhaps ours is a rarity, but if you approach them logically and with facts, they seem willing to work with the consumer. Heres hoping the system cleans better now too!
Published: February 26, 2013
Tom of Norwood, NJ
Source: consumeraffairs.com

Ive had this stainless steel GE Dishwasher model GDF645SMONES with the cont
Ive had this stainless steel GE Dishwasher model GDF645SMONES with the controls in the front for nearly a year. The dishwasher constantly comes on with the slightest accidental touch. However the buttons that control the cycle settings are extremely difficult to operate to cancel the lock or delay hours features. I have to literally bang on the buttons to get a response. My thumbs are now sore from the constant pushing to cancel that lock and delay features that came on accidentally. Once locked, good luck in canceling anything. Im so disgusted with this $600 dishwasher. Complaints to GE and the so-called warranty company that turned out to be one and the same, have fallen on deaf ears from the day I got it. Do yourself a huge favor, do NOT buy this dishwasher. Customer service is awful.
Published: February 5, 2021
Ameedah of Gwynn Oak, MD
Source: consumeraffairs.com

One of the most disgusting situations I have ever been in. I purchased a b
One of the most disgusting situations I have ever been in. I purchased a brand new home with all new GE appliances. I have since learned that a technician was sent out twice prior to our walk-through because the superintendent noticed the dishwasher wasnt working properly. I registered all my appliances online. The first time I used the dishwasher, it flooded the kitchen floor, causing the builder to have to repair baseboard and drywall. A technician came out and repaired it. I used it an additional two times and each time I did, it flooded my kitchen and a repairman came out. After the second time, I contacted GE customer care to open a case. The third time, I requested a new dishwasher and the customer care agent, Stephanie, stated that my new dishwasher was a discontinued model and so she suggested one that was a slight upgrade. I agreed to this change and she informed it would take approximately 24 hours to have it approved. I have since talked to seven different people at GE customer care. This was started when a company called Barlows Distributing showed up unannounced at my front door approximately hours after my discussion with GE. They said they were here to install my dishwasher. I was rather shocked, said the timing was impressive, and let them in the door. After they had drained the water standing in the then current dishwasher, they started to put in a replacement. I looked at the box and realized they were placing the same model in. I told them that was unacceptable, because according to GE, I was being approved for a different dishwasher. I then told the tech to stop installing it and called GE. GE had no idea where this dishwasher had come from. Then an unavailable number showed up on my cell phone and when I answered it, the woman spoke my first name and started talking about my dishwasher, stating the builder had ordered a new one. I asked her who she was twice and she would only tell me GE customer care and not her name. I have since learned her name was Julianna. She said that I had to take this dishwasher or I wouldnt have one at all. I took this as a threat. After spending countless hours on the phone with GE opening a case and discussing the issues, picking out an acceptable replacement, I was then told the builder made this decision. Not only was I thrown from person to person over a discontinued model, I was threatened, and further was told by the superintendent of construction that once the dishwasher was installed and we closed on the house, I had to handle all problems through GE. I own the dishwasher, not the builder. I registered the warranty, and I handled it through the proper channels. I feel I need an explicit apology from GE. One of their arms doesnt know what the other arm is doing. During this entire time, I had little use of my right hand and seven fractured vertebrae (for which I am permanently disabled) and had to physically wash 10 boxes of dishes that had been packed up due to our move and stand while doing it. GE has caused me property damage, stress, and severe physical pain, yet threatens me and yanks me from person to person.This is my house, my dishwasher, and this matter should have been handled directly with me, instead of inviting someone into my house that I had no connection to or knowledge of. The really sad thing is that I just purchased and had installed a $6500 water softener and reverse osmosis system for the whole house, manufactured by guess who...GE.
Published: August 16, 2011
Linda of Buckeye, AZ
Source: consumeraffairs.com

My ancient GE Profile Spacemaker II Sensor microwave, the successor to its
My ancient GE Profile Spacemaker II Sensor microwave, the successor to its predecessor, is consistent, great performance, reliable. I chose this model because I was happy with its performance. But it could be less chunky. I would like to remodel my compact kitchen, and a sleek newbie non-chunky GE Microwave Oven would be awesome!!! :)
Published: January 25, 2017
Rhoda of New York City, NY
Source: consumeraffairs.com

I owned a previous GE dishwasher 4 years ago and would give it excellent ra
I owned a previous GE dishwasher 4 years ago and would give it excellent ratings. I bought a newer top of the line version when I purchased a new home. It simply fails to clean dishes. Wet food that any dishwasher would remove, remained on the dishes. The drying cycle never dried the dishes. We have to hand wash the dishes now and have stopped using the dishwasher after 3 days of ownership because of health hazard. I called Lowes about this within days of the install. Lowes sent out the installer who claimed the machine was installed properly. Then Lowes scheduled a GE repairman to come to the home. We waited all day for him to arrive for a morning appointment. He never came. Lowes stepped up and is replacing the dishwasher with a non-GE product. I would not touch a GE product again given the lack of service and commitment to their product. I feel confident with Lowes, but not with GE - their ethics from engineering, manufacturing and servicing are very suspect with us.
Published: September 21, 2012
Steven of Reno, NV
Source: consumeraffairs.com

GE profile microwave TOUCH SCREEN pvm2070sm4ss - Almost new. Used properly.
GE profile microwave TOUCH SCREEN pvm2070sm4ss - Almost new. Used properly. Touch screen failure. TOUCH SCREEN does not function properly making it almost impossible to use the microwave. This Common Problem should be a RECALL.........
Published: November 2, 2014
joe of Keyport, NJ
Source: consumeraffairs.com

We purchased a new GE dishwasher from The Brick, after three washes it leak
We purchased a new GE dishwasher from The Brick, after three washes it leaked all over our new hardwood floors. I called The Brick and they said it was GEs problem. I called GE and they sent out a repairman who told us it was a broken seal on the pump and that this dishwasher is discontinued and he cant get the part. So, that would mean GE would have to replace our washer with a new one! We went back to The Brick and told them we did not want the GE washer and wanted to replace it with another brand as we were within the thirty day guarantee. No apology or well pay for the damage to your floor (floor is warped underneath) and guess what Im still waiting for a call back from GE!! Dont buy anything made by GE. You will regret it! As well, I will not be shopping at The Brick anymore.
Published: August 17, 2015
Teri of St Catharines, ON
Source: consumeraffairs.com

Ive been battling this dishwasher since it arrived 9 years-ago. It was a wa
Ive been battling this dishwasher since it arrived 9 years-ago. It was a warranty replacement we were stuck with from GE. Plus, we paid $300. We could never get it to clean dishes, no matter how we loaded it or what we used, so we gave up and hand washed dishes for years. This year, I am committed to getting the dishwasher working because of hand eczema. I took it apart and cleaned the sprayer arms, filter & wiped it down completely. I also ran a dishwasher cleaner through it. I finally got it to clean dishes, but only if they are thoroughly rinsed first and on the Pots/Pans setting. After a month, it stopped cleaning my dishes again. I took apart the dishwasher again, and cleaned everything. Now, glasses on the upper rack in the back are not all getting clean. I never overload it. Im convinced that GE Dishwashers are just junk. Someday, Id love to find a dishwasher that actually works. :-( Frustrated!!!
Published: August 13, 2019
Linda of Cogan Station, PA
Source: consumeraffairs.com

Today I heated some spaghetti sauce in my microwave and it splashed, so I w
Today I heated some spaghetti sauce in my microwave and it splashed, so I wiped it out. My microwave is built in and was pretty new and in the house when we bought it 4 years ago. It is in the base counter so I have to reach down to clean it. l havent had a problem with it but when I wiped the inside top I felt bumps and when I looked at the cloth to see what was on it, there was paint on it. That has never happened before so I of course looked and there is a fair amount of peeling paint in one spot. I have had microwave ovens for many years. Never had this problem with any other brand. What is that?? Can it be fixed? Is it dangerous???
Published: August 29, 2016
Peggy of Tacoma, WA
Source: consumeraffairs.com

Have a six-year-old GE Tall Tub Café dishwasher (model#GHDT168V00SS) I pur
Have a six-year-old GE Tall Tub Café dishwasher (model#GHDT168V00SS) I purchased at Home Depot in Denver. Also purchased a 5 Year Extended Warranty that I assumed was through GEs Extended Warranty Opportunity. The dishwasher suddenly began leaking and ruined our hardwood floors (I know, wood floors in kitchen not good; tell that to the builder). I called GEs customer care number and basically talked to a scripted robot. You dont have a warranty through GE, its a third-part insurer such as Assurant, I was told. Not worth repairing, and the warranty expired a few months ago. I know parts wear out, but for heavens sake, cant they build a dishwasher that doesnt leak from the bottom, underneath the unit, where water will seep unbeknownst to people, eventually destroying the floor? Guess not. So, no more GE appliances EVER. PERIOD! Switched to Samsung, LG and Maytag. Now, gotta spend a couple grand ($2K+) to repair the hardwood floor.
Published: March 16, 2019
Ted of Denver, CO
Source: consumeraffairs.com

2 year old GE ADORA dishwasher - I am so disturbed tonight after seeing wha
2 year old GE ADORA dishwasher - I am so disturbed tonight after seeing what happened to the protection rubber that is on the exterior of my dishwasher. I decided to buy a new dishwasher because the bottom tray would not stop when pulled out at the correct stopping point. Today I got my new dishwasher installed and when the installers pulled the old one out I was shocked to see that the protectant that I would assume was placed to protect my house was melted all over my wall behind the dishwasher. WOW. Talk about a MAJOR fire hazard. Thank God my house didnt catch on fire because of this faulty equipment. Check out my pictures and you will see the pile of protectant that was under, on my wall, and behind the dishwasher once it was pulled out. Sincerely concerned.
Published: July 1, 2015
Brandy of Castle Rock, CO
Source: consumeraffairs.com

Visa MasterCard

Site Secured By The Website Guardian
TOP