Appliance Types


Appliance Brands


Article Categories


More Articles


GE Appliances
GE Appliances

GE Appliance Repair

GE Appliances is your home for the best kitchen appliances, home products, parts and accessories, and support.


Dishwasher Repair

For the home, kitchen and beyond, GE manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of GE appliance repair from experienced professionals, your local Appliance Helper can help.

GE Dishwasher not cleaning 
Water Inlet Valve. The water inlet valve opens to allow water to enter the dishwasher. If the valve is clogged or defective, the dishwasher won’t get enough water to clean dishes properly. If the water inlet valve is clogged, replace it. Do not attempt to clean the water inlet valve—cleaning the valve could make it more likely to fail. 

GE Dishwasher not draining 
Drain Impeller. The drain impeller pushes water through the drain hose and into the garbage disposer or drain line. If the impeller is broken, replace it. 

GE Dishwasher buttons not working 
Touchpad. First, confirm that the dishwasher display is working. If the display is still working, try pressing some of the touchpad buttons. If some of the buttons respond correctly but others don’t, it is likely that the touchpad is at fault. (Some manufacturers sell the touchpad separately from the control panel. Other manufacturers require that you purchase the touchpad and control panel together. If you cannot replace the touchpad individually, replace the touchpad and control panel.) 

GE Dishwasher lights flashing or blinking 
Heating Element. The heating element heats up the water to operating temperature. If the water doesn’t reach the proper temperature after a set amount of time, a light on the control panel might start flashing. To determine if the heating element has burned out, use a multimeter to test it for continuity. If the heating element does not have continuity, replace it. 

GE Dishwasher leaking 
Water Inlet Valve. The water inlet valve opens to allow water to enter the dishwasher. If the water inlet valve is stuck open, the dishwasher will continue to fill with water until the dishwasher leaks or overflows. If the water inlet valve is at fault, replace it. Water inlet valves are not repairable—if the valve is defective, you must replace it. 

GE Dishwasher leaking from motor area 
Impeller and Seal Kit. First, try to determine the source of the leak. If the water is leaking from the motor shaft area, the motor shaft seal is likely defective. If the seal is defective, replace it. (Some manufacturers sell the seal independently of the impeller. Other manufacturers require that you purchase the impeller and seal together. Still other manufacturers require that you purchase the entire pump and motor assembly instead of the impeller and seal. It is usually more cost effective to replace the impeller and seal kit rather than the pump and motor assembly.) 

GE Dishwasher won't start 
Door Switch. The door switch prevents the dishwasher from running while the door is open. If the door switch is defective, the switch will prevent the dishwasher from running even when the door is closed. To determine if the door switch is at fault, use a multimeter to test the switch for continuity. If the switch does not have continuity, replace it. 

GE Dishwasher won't latch 
Door Hinge. If the door hinges are damaged, the door won’t be able to latch properly. Inspect the door hinges for damage. If a hinge is bent or broken, replace it. 

GE Dishwasher dispenser not dispensing soap 
Bi-Metal. The bi-metal actuator is a metal loop which acts as a latch for the dispenser door. As electricity is applied to the bi-metal, it deforms and bends away from the latch, releasing it. If the bi-metal is burned out, it won’t release the dispenser door. To determine if the bi-metal has burned out, use a multimeter to test it for continuity. If the bi-metal does not have continuity, replace it. In addition, make sure that the dishwasher is getting enough water. If the water level is too low, the wash motor may not draw enough current through the bimetal, causing the bimetal not to bend enough to work properly. 


Dryer Repair

For the home, kitchen and beyond, GE manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of GE appliance repair from experienced professionals, your local Appliance Helper can help.

GE Dryer Won't Start 
Thermal Fuse. The thermal fuse is a safety device designed to protect the dryer from overheating. The fuse is located on the blower housing or at the dryer’s heat source such as the heating element on electric dryers or at the burner on gas models. The fuse should be closed for continuity meaning it has a continuous electrical path through it when good. If overheated the fuse will have no continuity meaning the electrical path is broken and the fuse has blown. A multimeter can be used to test it for continuity. Be aware that a blown thermal fuse is an indication of a restricted exhaust vent from the dryer to the outside. Always check the dryer venting when replacing a blown thermal fuse. 

GE Dryer stopped spinning 
Drive Belt. The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley. Over time, the belt can break from normal use. If the belt is broken, the dryer won’t turn. To quickly determine if the belt is broken, reach into the dryer and turn the drum by hand. If the drum spins very easily, the belt is likely broken. Next, inspect the belt to confirm that it is broken. If the belt is broken, replace it. 

GE Dryer drum not turning 
Drive Belt. The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley. Over time, the belt can break from normal use. If the belt is broken, the dryer won’t turn. To quickly determine if the belt is broken, reach into the dryer and turn the drum by hand. If the drum spins very easily, the belt is likely broken. Next, inspect the belt to confirm that it is broken. If the belt is broken, replace it. 

GE Dryer takes too long 
Air Flow Problem. If the vent is clogged or partially clogged, it will restrict the airflow through the dryer, substantially increasing the drying time. To ensure proper dryer performance, you should clean your dryer’s venting system at least once per year. 

GE Dryer overheating 
Heating Element. The heating element warms the air before the air enters the dryer drum. If the element is partially shorted out, it may produce heat continuously, even if the dryer has reached the proper temperature. When this happens, the dryer gets too hot. To determine if the heating element is at fault, use a multimeter to test each terminal for continuity to the case. If the heating element has continuity to the case, it is shorted out. If the heating element is shorted out, replace it. 

GE Dryer won't stop 
Air Flow Problem. If the vent is clogged or partially clogged, it will restrict the airflow through the dryer, substantially increasing the drying time. To ensure proper dryer performance, you should clean your dryer’s venting system at least once per year. 

GE Dryer not heating 
Thermal Fuse. The thermal fuse is a safety device designed to protect the dryer from overheating. The fuse is located on the blower housing or at the dryer’s heat source such as the heating element on electric dryers or at the burner on gas models. The fuse should be closed for continuity meaning it has a continuous electrical path through it when good. If overheated the fuse will have no continuity meaning the electrical path is broken and the fuse has blown. A multimeter can be used to test it for continuity. Be aware that a blown thermal fuse is an indication of a restricted exhaust vent from the dryer to the outside. Always check the dryer venting when replacing a blown thermal fuse.  

GE Dryer tripping breaker 
The Circuit Breaker is Weak. Over time, circuit breakers can weaken. If the circuit breaker is weak, it may trip too often, even if the amperage draw is below the limit. If you have already checked all of the potentially defective dryer components, consider having an electrician replace the circuit breaker. 

GE Dryer makes noise 
Drive Belt. The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor. Over time, the drive belt can become frayed or otherwise damaged. If the drive belt is frayed or damaged, the dryer will be noisy as it turns. Inspect the drive belt for signs of wear. If the drive belt is worn, replace it. 


Microwave Repair

For the home, kitchen and beyond, GE manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of GE appliance repair from experienced professionals, your local Appliance Helper can help.

GE Microwave not heating 
Diode. The diode converts the A/C power output of the transformer to D/C, doubling the voltage to nearly 5,000 volts. This high voltage powers the magnetron to heat the food. If the diode burns out, the magnetron won’t receive enough voltage to operate, preventing the microwave from heating. When the diode fails, it is often visibly burned out. Inspect the diode and if the diode is burned out, replace it. If inspecting the diode proves inconclusive, test it with a multimeter that uses a 9-volt battery or put a 9-volt battery in series with the diode. When the leads are reversed, the diode should only have continuity in one direction. (Warning: The microwave oven can store a lethal amount of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the high running voltage and the potential for electric shock, it is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the diode.) 

GE Microwave not working 
Line Fuse. If too much current passes through the microwave circuitry, the line fuse will blow. If the line fuse blows, the microwave won’t start. To determine if the line fuse is at fault, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it. In addition, you should investigate and resolve the problem that caused the fuse to blow. If you don’t resolve the underlying issue, the new fuse will blow too. (Caution: The microwave oven can store thousands of volts of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the potential for electric shock, it is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the line fuse.) 

GE Microwave light bulb not working 
Light Bulb. The light bulb itself might be burned out. Replace the light bulb before replacing any of the parts associated with the light bulb 

GE Microwave shuts off after a few seconds 
Door Switch. A door switch might be failing intermittently. Check each of the door switches for signs of overheating, arcing, or burning. If you don’t see any obvious signs of failure, use a multimeter to test each switch for continuity. If any of the switches is visibly damaged or only has intermittent continuity, replace it. 

GE Microwave turntable not turning 
Turntable Motor. Use a multimeter to test the motor for continuity. If the turntable motor does not have continuity, replace it. 

GE Microwave buttons not working 
Touchpad. To determine if the touchpad is defective, try pressing each of the buttons on the control panel. If some of the buttons respond correctly while others don’t, replace the touchpad. 

GE Microwave display not working 
Main Control Board. If the display goes out partially, the display board is more commonly at fault. If the display isn’t working at all, either the main control board or the display board could be at fault. 

GE Microwave turns on by itself 
Main Control Board. First, make sure that the touchpad is working properly. If the touchpad is working properly, the main control board is likely at fault. If the control board is defective, replace it. 

GE Microwave is sparking or arcing 
Waveguide Cover. The waveguide cover might be damaged and shorting out. Try removing the waveguide cover and see if the problem resolves. If the waveguide cover is burnt or will not stay in place, replace it. 


Range Repair

For the home, kitchen and beyond, GE manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of GE appliance repair from experienced professionals, your local Appliance Helper can help.

GE Oven not heating 
Igniter. The igniter is the most commonly defective part for an oven not heating. The igniter has two main functions. First, the igniter draws electrical current through the oven safety valve to open it. Second, the igniter gets hot enough to glow and ignite the gas in the oven burner. If the igniter gets weak, it will fail to open the safety valve correctly. If the valve does not open, the oven will not heat. To determine if the igniter is defective, observe the igniter when the oven is on. If the igniter glows for more than 90 seconds without igniting the gas flame, this indicates that the igniter is too weak to open the valve. If the igniter is weak, replace it. If the igniter does not glow at all, use a multimeter to test the igniter for continuity. If the igniter does not have continuity, replace it. 

GE Oven doesn't bake evenly 
Bake Element. If the bake element is burned out, the oven will only be heated by the broil element. This will cause the oven to heat unevenly. When the bake element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element is not heating. Often, if the element has burned out, it will be visibly damaged. Inspect the bake element for holes or blisters. To determine if the bake element has burned out, use a multimeter to test the element for continuity. If the bake element does not have continuity, replace it. 

GE Oven broiler not working 
Broil Element. The broiler element may have burned out. When the broil element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element is not heating. Often, if the element has burned out, it will be visibly damaged. Inspect the broil element for holes or blisters. To determine if the broil element has burned out, use a multimeter to test the element for continuity. If the broil element does not have continuity, replace it. 

GE Stove heating element not working 
Surface Element Board. The surface element board has relays that regulate the power supply to the burners. If one or more of the relays fails, the surface element won’t work. If two or more burners fail at the same time, this indicates that the surface element board is likely at fault. If only one surface element won’t work, use a multimeter to test the element for continuity. If the surface element has continuity, the surface element board might be defective. 

GE Stove burner won't light 
Spark Module. The spark modules provides power to each surface burner spark electrode. If the burner is produces a weak spark, or if the burner sparks intermittently, the spark module might be defective. Before replacing the spark module, first check the spark electrode and the spark wire. If the spark electrode and spark wire are not at fault, the spark module is likely defective. If the spark module is defective, replace it. 

GE Oven temperature not accurate 
Bake Element. When the bake element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element is not heating. Often, if the heating element has burned out, it will be visibly damaged. Inspect the heating element for holes or blisters. To determine if the bake element has burned out, use a multimeter to test the element for continuity. If the bake element does not have continuity, replace it. 

GE Oven light is out 
Light Assembly. If the oven light is out, the entire light assembly may need to be replaced. Often the light assembly components are not sold separately. 

GE Oven won't turn on 
Bake Element. When the bake element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element is not heating. Often, if the heating element has burned out, it will be visibly damaged. Inspect the heating element for holes or blisters. To determine if the bake element has burned out, use a multimeter to test the element for continuity. If the bake element does not have continuity, replace it. 

GE Oven not self-cleaning 
Door Lock Motor and Switch Assembly. During the oven's self-cleaning cycle, the door lock switch activates the door lock motor to prevent the oven door from being opened. If the door lock motor and switch assembly is defective, the oven door will not unlock once the self-cleaning cycle is complete. On most ovens, you can open the oven door by removing certain screws or panels. Check your owner's manual for further instructions. 


Refrigerator Repair

For the home, kitchen and beyond, GE manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of GE appliance repair from experienced professionals, your local Appliance Helper can help.

My GE Refrigerator is Not Cooling 
Condenser Coils are Dirty. The condenser coils are usually located under the refrigerator. They dissipate heat as refrigerant passes through them. If the condenser coils are dirty, they won’t dissipate the heat effectively. As debris builds up on the coils, the refrigerator becomes less efficient, causing the refrigerator to work harder to cool down. If the coils are significantly dirty, the refrigerator will not be able to maintain the proper temperature. Check the condenser coils to determine if they are dirty—if the condenser coils are dirty, clean them. 

GE Refrigerator water dispenser not working 
Water Tube in Door is Frozen. To determine if the water supply tube is frozen, disconnect the tube at the bottom of the door and blow air through it. If air does not pass through, this indicates that the water supply tube is frozen. If the water supply tube is frozen, thaw it out. In addition, ensure that the freezer is kept at the proper temperature. The freezer temperature should be kept from 0-10 degrees Fahrenheit. If the freezer is too cold, the water line may freeze. 

Why is my GE Refrigerator Not Making Ice? 
Freezer Temperature is Above 10 Degrees F (-12C). If the freezer temperature is above 10 degrees Fahrenheit (-12C), the ice maker will not produce ice cubes efficiently. The freezer temperature should be set between 0 and 5 degrees Fahrenheit (-18 to -15C) for the ice maker to work properly. If the freezer temperature is too high, ensure that the condenser coils are clear of debris and the condenser fan is working properly. In addition, check to see if frost has accumulated on the evaporator coils. If the evaporator coils are frosted over, part of the defrost system has likely failed. 

GE Refrigerator ice dispenser not working 
Dispenser Control Board. The dispenser control board governs most of the functions of the dispenser system. If the control board is faulty, it may stop supplying power to the entire dispenser system. If only one dispenser part is not working, test each of the dispenser components before testing the control board. It is more likely that a single part has failed. If the entire dispenser system is not working, the control board is more likely to be at fault. 

GE Refrigerator not defrosting 
Defrost Control Board. The defrost control board determines how often to run the defrost cycle. If the board fails, the refrigerator will not go into the defrost cycle. Before replacing the defrost control board, first test the defrost heater and defrost thermostat. If the defrost heater and defrost thermostat are working properly, the defrost control board is likely defective. 

GE Refrigerator is noisy or loud 
Fan Blade. If the refrigerator is noisy or loud, especially when one of the doors are opened, either the evaporator or condenser fan blade may be at fault. First, check out the evaporator fan blade in the freezer behind the back panel. Try turning it by hand. If the fan blade does not turn freely, check to see if the blade is rubbing against something or if something is caught in the blade. Additionally, check the condenser fan blade in the back underside of the refrigerator to determine if it has any obstructions. 

GE Refrigerator defrost drain clogged 
Clogged or Freezing Defrost Drain. The defrost drain might be clogged or frozen. If the defrost drain is frozen, the water will overflow the drain trough and drip down to the bottom of the compartment. If the defrost drain is frozen, thaw it out and ensure that the drain is clear of debris. 

GE Refrigerator freezer is cold but refrigerator is warm 
The Evaporator Coils are Frosted Over. The defrost heater assembly turns on a few times throughout the day to melt away any frost that may have accumulated on the evaporator coils. If the defrost heater assembly is defective, frost will continue to accumulate on the evaporator coils, and the coils will become plugged with frost. If the evaporator coils are frosted over, the airflow through the coils will be restricted, causing the refrigerator not to cool. Check the evaporator coils to determine if they are frosted over. If the evaporator coils are frosted over, test each component of the defrost system. 

Why is My GE Refrigerator Leaking Water? 
Clogged or Freezing Defrost Drain. If the defrost drain is frozen, the water will overflow the drain trough and drip down to the bottom of the compartment. This water can eventually leak onto the floor. Check the defrost drain to determine if it is clogged or frozen. If the defrost drain is frozen, thaw the ice. In addition, flush the drain with hot water to ensure that it is clear of debris. 


Washer Repair

For the home, kitchen and beyond, GE manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of GE appliance repair from experienced professionals, your local Appliance Helper can help.

GE Washer won't spin 
Lid Switch Assembly. The lid switch assembly prevents the washer from spinning when the lid is open. If the lid switch assembly fails, the washer will not spin. To determine if the lid switch assembly is defective, use a multimeter to test the lid switch for continuity. If the lid switch does not have continuity, replace it. 

GE Washer is making loud noise 
Bearing. The tub bearing is mounted in the middle of the outer tub. The tub bearing helps to keep the inner tub spinning smoothly. Replacing the tub bearing is a very involved repair and will require disassembling most of the washer. If the tub bearing is defective, we recommend replacing both the outer tub and bearing. 

GE Washer won't agitate 
Agitator Repair Kit. If the washer won't agitate, replacing the agitator repair kit may solve the problem. The kit contains the agitator components that are most likely to wear out and/or fail. If any of the parts are worn out, stripped, or damaged, replace the kit. 

GE Washer won't drain 
Drain Pump. Sometimes, small objects or articles of clothing can get caught in the drain pump. To determine if anything is blocking the drain pump, remove the drain pump and check the pump for obstructions. If the drain pump is clear of obstructions, but is still noisy during the drain cycle, replace the drain pump. 

GE Washer vibrating or shaking 
Shock Absorber. One or more of the shock absorbers might be broken or worn out. The shock absorbers dampen the vibration of the washer tub. If one or more of the shock absorbers are worn out, the washer will vibrate or shake. Sometimes, when a washer is moved to another location, the shock absorbers can separate. Check the shock absorbers to ensure that they are positioned correctly, and inspect them for damage and wear. If one or more of the shock absorbers are broken or worn out, we recommend replacing all of the shock absorbers as a preventative measure. 

GE Washer fills slowly or will not fill at all 
Water Inlet Valve. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the wash may fill slowly or not fill at all. The water inlet valve requires sufficient water pressure to function properly. First, check the water pressure to determine that it is adequate. If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve. 

GE Washer leaking water 
Drain Pump. The drain pump pumps water out the drain hose. If the drain pump is cracked or damaged, or if the bearings are worn out, the drain pump may leak water. The drain pump is not repairable—if the pump is leaking water, replace it. 

GE Washer won't start 
Timer. The timer is frequently misdiagnosed—before replacing the timer, first check all of the more commonly defective parts. To determine if the timer is defective, consult your washer’s wiring diagram and use a multimeter to test the timer for continuity. 

GE Washer won't spin or agitate 
Drive Belt. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. 


Water Heater Repair

For the home, kitchen and beyond, GE manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of GE appliance repair from experienced professionals, your local Appliance Helper can help.

Water heater not heating 
Some gas water heaters have a thermocouple. The thermocouple detects the pilot flame. If the thermocouple does not detect a flame, it will prevent the gas valve from opening. 

Water heater leaking 
The temperature and pressure relief valve opens to stabilize temperature or pressure of the water heater if the temperature or pressure exceeds the proper level. The temperature and pressure relief valve opens at a set temperature. This temperature is indicated on the water heater. If the temperature and pressure relief valve leaks even though it has not reached the indicated relief temperature, replace it. 

Water heater not lighting 
Some water heaters use an igniter to ignite the gas. If the igniter fails, the burner will not light. To determine if the igniter is defective, first make sure the igniter is getting voltage. If the igniter is getting voltage, but it doesn’t glow, this indicates that the igniter is defective and should be replaced. 

Water heater too hot 
The thermostat determines the maximum water temperature setting. If the thermostat is defective, the water temperature may not be set at the proper level. To determine if the thermostat is defective, assess hot water temperature from the nearest faucet. If the water temperature is hotter than the selected thermostat setting, this indicates that the thermostat is defective. If the thermostat is defective, replace the gas valve and thermostat assembly. We recommend a set temperature of 120 degrees or fewer to prevent the risk of scalding.



GE Appliance Repair

GE appliance service

GE appliance help

GE appliance assistance

GE appliance maintenance


Product Reviews:

Bought brand new GE Profile DW PDT845SSJSS as part of four appliance packag
Bought brand new GE Profile DW PDT845SSJSS as part of four appliance package to be installed as part of kitchen renovation. Bought in April 2018, renovation delayed until August 2018, install of appliances October 2018, installer by contractor plumber- excellent seasoned experienced installer. Never used DW until moving things into new kitchen. Washed dishes off in DW before placing in cabinets. After 3rd cycle- DW stopped working stating leak detected - contact GE. Are you kidding me? Brand new appliance! We had original installer come out- no leak- no visible water- we went to placed we purchased DW from - local place - Ray’s Appliances- asked for replacement DW. Was told we would have to pay for installation of 2nd DW at 225 charge. Are you kidding me? GE guy came out and did something to DW to fix it but said problem could return... Serious??? Well -DW worked for a few cycles- now displays leak detected again! Called GE and coming out 12/2. Ridiculous- I want a NEW DW with free installation! I’m paying @971 bucks for something that didn’t work from the outset!!!
Published: November 23, 2018
Donna of Lafayette Hill, PA
Source: consumeraffairs.com

Weve had our new over the stove microwave (GE Profile Microwave Oven PVM217
Weve had our new over the stove microwave (GE Profile Microwave Oven PVM2170SR1SS) just over one year and the oven light went out. The owners manual has no information about how to replace the light. I called GE customer assistance office and they said it requires a technician to come to the house to replace the bulb. A service call would cost around $95 minimum. This is a ridiculous requirement to make consumers do a service call for an oven light. The owners manual does show how to replace the charcoal air filter, if you use one, by removing the plastic cover across the top of the oven with the door open. Guess what? I removed the two screws holding the plastic cover and sure enough, there was also the access to the cover to access the oven light. You just remove the one screw and the small cover plate can be removed! Be sure to turn off the power to the oven before removing the small 50w Halogen G8 light bulb (Home Depot $5.00). My complaint about GE is that they do not give the homeowner information about replacing this oven light, but instead require you to pay for a service call. The irony is that the owners manual tells you how to access the filter by removing the plastic grill and thats how you also access the panel to replace the oven light bulb. They also tell you how to replace the light bulb that provides light to your range, so it cant be a safety issue about replacing light bulbs. Requiring the consumer to request a service call for $95 just to replace the oven light, when GE could have easily put the procedure in the owners manual, is a real consumer ripoff!
Published: February 3, 2013
Thomas of Mclean, VA
Source: consumeraffairs.com

I wish I could rate this dishwasher ZERO stars. I bought my first GE cafe s
I wish I could rate this dishwasher ZERO stars. I bought my first GE cafe series approximately 6 months ago and after the first week, there were three separate, unrelated problems. I called GE repair and the serviceman came out and said he fixed all the problems. He did not. I contacted the store where I bought it, and after contacted GE directly was able to get a brand new one. After two months, problems started again. Once again the repairman came out. Long story short - 2 months, and three sick days later (on my part) dishwasher is still not cleaning dishes thoroughly. I contacted GE several more times and they sent me some dishwasher cleaner and offered me a discount on a new GE dishwasher.... I will never purchase another GE anything and advise everyone else to do the same!
Published: September 30, 2015
Jessica of Jefferson, MA
Source: consumeraffairs.com

Im very pleased with this microwave. Size appearance and price were right o
Im very pleased with this microwave. Size appearance and price were right on point. This has a built in turntable with presets that actually work! It is an easy to find product and available thru quite a few retailers.
Published: July 13, 2019
Terry of Vancouver, WA
Source: consumeraffairs.com

Our Spacemaker microwave, which was installed over the stove August 2008, s
Our Spacemaker microwave, which was installed over the stove August 2008, suddenly stopped heating food. My husband called GE, and their phone advisor advised us the microwave was under warranty. She said her computer screen showed our product registration, and she also saw we owned three other GE products. Fast forward, the GE repairman came and said the microwave repair cost would be around $400. The heating part wasnt under warranty nor was the labor. Mind you, the entire microwave (new) was under $400. We called the GE service center, and they refused to honor what their representative had told us. The most they offered was 50% off. I dont accept the premise that a new appliance should only last four years. I will replace my unusable microwave with a competitor’s brand and will pledge never to purchase a GE appliance again. I will also sell my GE stock, for I now understand why its going nowhere.
Published: September 21, 2012
Diane of Hillsborough, NJ
Source: consumeraffairs.com

I guess my GE Profile dishwasher is a lemon. Sounds like it from all the ot
I guess my GE Profile dishwasher is a lemon. Sounds like it from all the other reviews. Same deal - purchased it in July of 2016 and by October 2016 it went out. Technician that was sent told me it was the electric and I needed to have an electrician fix the fuse. Electrician came out and said it had electric, that it was the dishwasher that failed. Next technician fixed it and said the electronic panels get confused. Three days off of work. December, 2016 the dishwasher failed again. Had no dishwasher throughout the holidays. They scheduled service technician and then cancelled because the one technician they had was out sick.Today, January 9th, they called to let us know they were on the way, but never called the number they were supposed to, so now we are totally taken off the schedule. Ive been on hold and disconnected three times and now have been on hold for one hour and 6 minutes. DONT BUY GE APPLIANCES - Terrible service and crappy appliances that dont work. This is really sickening since I have ALWAYS used GE appliances.
Published: January 9, 2017
Peggy of Cold Spring, KY
Source: consumeraffairs.com

GE Model PDW9280J10SS Fire - Many GE Profile dishwashers have been recalled
GE Model PDW9280J10SS Fire - Many GE Profile dishwashers have been recalled during the same time frame as the model we purchased, but it is not listed as one of the recall models. Just as many other complaints, ours started to smoke out of the top of the front door and filled our house with smoke. Thank God we were there to shut it off. The next day I opened up the front door to see what had been burning and it had holes burnt in front and back of the main circuit box (for lack of better name), one burn mark right where the main wire harness plugs in and burnt right through it. This is the same description many others have written. There is a problem with all of these Profile dishwashers purchased between 2006 and 2009 (ours 2007). If we had not been home, who knows what would have happened?
Published: January 6, 2013
Kevin of Seattle, WA
Source: consumeraffairs.com

Its a over the range model & came with a house purchase. It’s worked
Its a over the range model & came with a house purchase. It’s worked flawlessly for over 5 years now - even after being left with no air conditioning in FL for months on end. The only thing I could think to make it better is making it easier to choose longer length cook times. Button for half min & dial for all the rest can be irritating for your 16 min food.
Published: July 12, 2019
M of Lakeland, FL
Source: consumeraffairs.com

We moved in to our home in 2006 and it had a GE Monogram Microwave built in
We moved in to our home in 2006 and it had a GE Monogram Microwave built in. The microwave died and I purchased a similar GE Monogram microwave to match our kitchen in 2014. That microwave died exactly 17 months later. Fortunately, we had a home warranty program as we are selling our home. I figured that this saved me the effort to complain to GE about their product... Wrong. The Home Warranty program sent a repairman who said we can order a part. A few days later I received a call that they would replace the microwave. OK... I checked online as well as with a local retailer to see which model is the replacement model, and trim kit. Today (about 10 days after I first called for service) they delivered the new GE Monogram microwave and installed it. Fortunately, I asked to test it and we tried to boil a cup of water. The contents in the oven being cooked were not visible. Either the light was too dim or the shading on the door was too dark. I have never seen a Microwave where you could not view what is inside. I called GE Customer Service while the installers were there and they refused to allow me to keep it until a replacement was delivered. They had to deinstall it, re-install my old (non working unit) and take the new one back. I called GE with my homeowners claim info and they sent me back to the Homeowner Warranty company to start the claim all over. Ridiculous.Instead of a replacement they offered me a cash value which was 60% of what I paid the retailers. When I asked why that amount? They only provide the value based on what the Warranty company gets the products/services for (wholesale cost). Net: If I used the money to buy another product it would cost me out-of-pocket for replacement. I am hoping the new unit to be delivered in the next 3 days works better. Otherwise, GE has a significant design flaw that doesnt allow you to view what is cooking in the Microwave. If thats the case, why have a window at all? Fyi - My Panasonic Microwave in our basement is working fine.... and has for years.
Published: March 9, 2016
Gary of Basking Ridge, NJ
Source: consumeraffairs.com

We bought a GE dishwasher after owning a KitchenAid. The GE is quieter, was
We bought a GE dishwasher after owning a KitchenAid. The GE is quieter, washes better, takes longer, but it doesnt really matter. I use Quantum tablets and everything is always clean when we are done.
Published: January 22, 2018
John of Mechanicsburg, PA
Source: consumeraffairs.com

My GE dishwasher is very quiet. It is a decent dishwasher and have had no p
My GE dishwasher is very quiet. It is a decent dishwasher and have had no problems with it in 14 years. I do sometimes have a problem getting it to reset to start at the beginning of the cycle, but it finally does. Other than that, it is fine.
Published: January 15, 2018
Marsha of Cape Coral, FL
Source: consumeraffairs.com

After having my Cafe Stovetop for about a year and a half, there was a elec
After having my Cafe Stovetop for about a year and a half, there was a electrical component malfunction. During this, smoke came out of the stovetop and it smelled of electrical burning. I sent a complaint to GE since several components were damaged. Knowing that the warranty was only for 1 year, there would be nothing they could do except sell me the parts.
Published: January 23, 2019
Deanna of Ellijay, GA
Source: consumeraffairs.com

Purchased the cafe dishwasher in March. We are now on our second one as the
Purchased the cafe dishwasher in March. We are now on our second one as the first did not work and now this one does not work. It worked fine for the first couple of months and now it’s doing the same thing as the first one. Pump is on the fritz apparently. Truly disappointed. We owned the cafe dishwasher at our last house and loved it so we made sure that we purchased the same one when we bought our new house.
Published: November 15, 2020
Darcy of Norwich, ON
Source: consumeraffairs.com

My microwave is less than a yr old and has been serviced 2 times. It is not
My microwave is less than a yr old and has been serviced 2 times. It is not working right still and before it broke last time it would not turn off at all, would keep cooking with the door open! I have 4 small children and the 2 older kids use the microwave. I called GE and talked to customer service about replacing it. The lady said no and that they will repair it (again) but not replace it! Well it broke the 1st time before it was 6 mo old! This microwave is a lemon and they should make it right! It is a health hazard! This is a large microwave and was almost $200! Please someone listen to me, I need HELP!
Published: February 3, 2014
trina of Anderson, MO
Source: consumeraffairs.com

I purchased a new Modular home. It came equipped with all GE appliances bac
I purchased a new Modular home. It came equipped with all GE appliances back in August of 2006. The dishwasher has recently been burning the basket prongs off, as apparently the coils are over heating! I had called GE about the danger of it being another recall. They informed me there would be an $89 service call. I dont have this kind of money; I am a senior citizen on Social Security. How can they charge me for a potential fire hazard?
Published: August 15, 2012
lORAINE of Williamstown, NJ
Source: consumeraffairs.com

We remodeled our kitchen and bought full line of GE café appliances which
We remodeled our kitchen and bought full line of GE café appliances which we have not been happy. Microwave screen cracked in the first three months; refrigerator is at max cooling but still does not cool or freeze enough; dishwasher has never cleaned well and marks my dishes with gray streaks and its control panel quit working and had to be replaced. They said that it was my soap, water etc., even though it never happened with previous dishwasher. All this in the first ten months of ownership of a couple with no family at home. Servicemen were nice and polite but their products are crummy. Dont buy them.
Published: September 1, 2011
Mary of New Berlin, WI
Source: consumeraffairs.com

Three nights ago, I loaded my GE Profile Dishwasher, model # PDW9880L00SS a
Three nights ago, I loaded my GE Profile Dishwasher, model # PDW9880L00SS and began the wash cycle. The wash cycle completed and I went off to bed leaving it on the dry cycle. The next morning I smelled a burning smell but did not know where it was coming from in my home. A few hours later, my husband began searching all of the appliances in our home to see what the burning smell was. When he opened the dishwasher smoke came out of it and everything in it was completely burned. Apparently the drying mechanism never turned off after the wash cycle or it turned itself back on only on the dry cycle. I dont know. But I know one thing for sure, we are lucky that my husband was home because I left and if he wasnt there, Im positive that the dishwasher would have caught on fire causing severe damage to our home. I will never purchase a GE appliance again. Note, I also have problems with my GE refrigerator and my GE Profile microwave and our dryer. Weve had to replace the dryer and the microwave and weve repaired the refrigerator. I have a repair person coming out to see if the dishwasher is repairable, but I dont think it will be. This is terrible.
Published: February 2, 2012
T of Rancho Cucamonga, CA
Source: consumeraffairs.com

GE Dishwasher model #GDF610PSJ5SS stopped working (would not even turn on)
GE Dishwasher model #GDF610PSJ5SS stopped working (would not even turn on) a little over 3 months. Because it was purchased over a year ago for a spec home we purchased, GE would not honor the warranty even though we had only purchased the home 3 months prior. Repair, if possible, most likely would be more than buying a new one. Recommend avoiding GE products. This is our 5th home, never had problem with other brands in previous homes!
Published: August 13, 2019
Jeanne of Saint Marys, GA
Source: consumeraffairs.com

I remodeled my house 5 years ago and went with the GE Profile appliances in
I remodeled my house 5 years ago and went with the GE Profile appliances in my kitchen. Last week I had run the dish washer cycle and noticed the soap had not dissolved and the dishes didnt seem to be clean so I ran the cycle again. I started it at about 8 pm and we went to bed not thinking any more about it. About 1 am I awoke to a horrible plastic burning smell. I checked through the whole house and could not find where it was coming from until I entered the kitchen. As I entered the room my eyes started streaming from the burn. I opened the dishwasher and smoke starting bellowing out of it. Not just smoke but a toxic smoke filled the room. The inside of the dishwasher was so hot and everything plastic inside was melted. The bottom drawer and parts of the dishwasher were also melted. The silverware tray full of silverware was all melted together. This all occurred in a matter of 5 hours. Had I not woke up when I did, who knows if we would have woke up.The house was full of toxic smoke that did not trigger the smoke detectors. We just went ahead and purchased a new dishwasher and had it installed yesterday. This morning my husband decided to do a little research on this product and found there was a recall last year. I contacted GE and found that our model was not part of the recall because it has a stainless steel interior, only the plastic interiors are part of the recall. I also found out that had we called them and had them send out a certified GE technician look at it, they would replace it. Too late it has already been replaced and sent to the recycle center. I did take pictures and have record of the model and serial number which doesnt matter. I just want to get it out there that this product is also dangerous and a fire hazard. This product could have easily caused a fire in my home. I also wish I would have done more research before we replaced it. Our new dishwasher is a GE Profile...
Published: August 7, 2013
Karen of Murray, UT
Source: consumeraffairs.com

We purchased 3 GE Profile Appliances when we remodeled our kitchen. It turn
We purchased 3 GE Profile Appliances when we remodeled our kitchen. It turns out that they are junk. The microwave and the refrigerator have had to be repaired several times and the dishwasher went downhill very fast and we had to replace it as it was not cleaning the dishes correctly. We now are living with a microwave that has peeling paint that I hope is not damaging our health that they would not do anything about. And a refrigerator that was repaired today at the cost of almost $400 and it still is not cooling down. So now I have to wait 48 hours for another service call. Dont buy GE unless you want Junk!
Published: September 9, 2015
Sharon of Cape May Court House, NJ
Source: consumeraffairs.com

I have had 2 Profile dishwashers in the past 3 months. I have not been able
I have had 2 Profile dishwashers in the past 3 months. I have not been able to use either one. First one had a cracked tub and the replacement would not run. I tried for hours to contact GE customer service and was placed on hold for almost an hour before they closed for the day. Not only is this washer a piece of garbage, GE customer service is terrible. Do not and I will say this again do not but this product.
Published: September 16, 2020
John of Montesano, WA
Source: consumeraffairs.com

I bought GE dishwasher model #GDF570SGJOCC from a local appliance dealer in
I bought GE dishwasher model #GDF570SGJOCC from a local appliance dealer in April, 2017. The machine cost about $600, and $150 to install. Today I learned the circuit board is caput and it will cost $600 to replace it. I will never again buy a GE product-- 2 years of service and it needs to be replaced.
Published: September 21, 2019
Dale of Madison, WI
Source: consumeraffairs.com

We bought a new GE microwave oven in 2007. It failed in 2018 after much, mu
We bought a new GE microwave oven in 2007. It failed in 2018 after much, much use. We replaced it with a Whirlpool which failed in one week. Lowe’s let us return it and we bought another GE like our original and we are very happy with it.
Published: January 4, 2021
Thurman of Camden, SC
Source: consumeraffairs.com

I have a microwave that has a rack inside which gives you options other tha
I have a microwave that has a rack inside which gives you options other than using the rotating plate inside. Overall it works quite well. I did not purchase this microwave, it came with the apartment. Not sure if I would purchase this brand if I were to buy it for my own home.
Published: December 14, 2015
Cynthia of Jamaica, NY
Source: consumeraffairs.com

Our GE microwave, manufactured in 2012, has been running fine, but the door
Our GE microwave, manufactured in 2012, has been running fine, but the door handle has cracked on the bottom. Imagine my shock when I found the cheapest price for a PLASTIC handle was well over $100. How can this be?
Published: December 22, 2017
Robert of Haines City, FL
Source: consumeraffairs.com

I own a GE Model #JNM1731DM1CC that came with my condo, in March of 2008. A
I own a GE Model #JNM1731DM1CC that came with my condo, in March of 2008. After two weeks, the tray was spinning, and nothing was heating up. They came, and replaced something, and it worked again. It is now November of 2011, and the ** thing doesnt go off. When the timer stops, and you open the door, the table turns, and the microwave is on, letting rays come right out at you. I have to unplug it after every use, so that I dont expose myself to rays coming from the microwave. I spoke with several appliance repair shops, and they told me that it is probably the circuit board, and that to repair it would run at least $200. I am so disgusted with GE. I also have a stove that practically blew up, when the door shattered, after only having it for six months. They had to come and replace the whole glass front. I doubt very much, if they will help me, because it took at least 12 calls to get them to replace the glass door, with the glass all over the place, and inside the oven, four days before Easter dinner at my house.
Published: November 17, 2011
Hilda of Easton, PA
Source: consumeraffairs.com

Dishwasher is very loud. Even on the longest setting, it doesnt get the dis
Dishwasher is very loud. Even on the longest setting, it doesnt get the dishes clean. The rack system, both top and bottom, isnt set up to handle a lot of items. Very poor quality and design.
Published: January 19, 2018
Debra of Milwaukee, WI
Source: consumeraffairs.com

Not very satisfied with the functionality. Turntable does not work or has e
Not very satisfied with the functionality. Turntable does not work or has ever worked. Time features and power adjustments are not very intuitive. I would not recommend this brand, I believe there are other brands out there are much better for the same price range.
Published: January 17, 2017
Joseph of Escondido, CA
Source: consumeraffairs.com

My husband ran our 4-year old GE stainless steel dishwasher (PDW8980N00SS)
My husband ran our 4-year old GE stainless steel dishwasher (PDW8980N00SS) at 9 pm, 2/4/13. At 11 pm, he emptied and put away the dishes. At midnight, we went to bed. At 4:50 am on 2/5/13, we were awakened by a burning smell and discovered the heating element of the dishwasher either turned back on or never turned off. We were unable to touch the granite counter, the front of the dishwasher, and both wooden cabinets on either side of the dishwasher were very warm. The spinning arms and other plastic parts were melted. The only way it could be turned off was to unplug it from the outlet in the cabinet. We were leaving for the airport at 7:30 am on 2/5/13, so needless to say, we would have lost our home if this occurred a couple of hours later. The Assurant tech said it was repairable and ordered a part, which would take at least a week. Assurant customer service had us call GE. When we stated we didnt want the faulty dishwasher repaired, but wanted a new dishwasher, the best the GE customer service rep could offer us was 38-40% off several new different Profile dishwashers. After reading page after page of bad reviews, most of which detail either one or multiple fires from different GE dishwashers, we dont even want another GE dishwasher in our home. We already needed the smart soap dispenser replaced, since it clogs periodically and doesnt wash dishes very well. We also have a countertop GE Profile microwave, and the turntable motor has gone out 3 times so far. Weve purchased the replacement motors ourselves since it isnt under Assurant insurance. Not sure what the resolution will be on the dishwasher, but wed be happy if GE would give us at least $500 toward a different brand dishwasher. I know well never ever buy another GE appliance after this. We wouldnt sleep at night or ever want to go out of the house without unplugging another GE dishwasher, so dont want one.
Published: March 1, 2013
Teresa of Wood Dale, IL
Source: consumeraffairs.com

We purchased our Adora over-the-stove microwave oven from Home Depot. The A
We purchased our Adora over-the-stove microwave oven from Home Depot. The Adora brand is made exclusively for Home Depot and were sold on its special functions and value. Well now, 3 years later, this exclusive models glass fogs up when we use it. There are only 2 of us living at home. We use it maybe 4 or 5 times a day. A microwaves typical lifetime is 9 to 10 years. Also, by the way, when we turn on the fan to highest, it sounds like an express train hurtling through our kitchen. Our dog had a heart attack and died the first day we operated it. No he didnt. We dont even have a dog. But you get the picture.
Published: July 11, 2020
Neil of Louisville, KY
Source: consumeraffairs.com

I purchased a GE microwave from Best Buy about a year ago. Every time I wip
I purchased a GE microwave from Best Buy about a year ago. Every time I wipe it clean, white paint chips come off the inside. This cannot be safe for me or my children. I did contact the company and they were of no help at all. They said that because I heat up liquids in the microwave, this will happen. Duh! I would not recommend purchasing a GE product of any kind (oven, fridge, etc). Their customer service is awful and their products do not last.
Published: March 26, 2013
Margaret of East Aurora, NY
Source: consumeraffairs.com

While the microwave works fine, as far as microwaves go; it does heat uneve
While the microwave works fine, as far as microwaves go; it does heat unevenly but eventually gets the job done, the interior is cracked and shows signs of rust and deterioration. I dont remember ever seeing this on in previously owned microwaves. I would only use it for basic heating and reheating.
Published: December 27, 2020
T of Basking Ridge, NJ
Source: consumeraffairs.com

GE profile microwave convection - over the gas range. Oven temperature does
GE profile microwave convection - over the gas range. Oven temperature does not heat up more than the 370 degree, even if its set to maximum (450 degree). I purchased 4 ovens in the past year, all have the same defect.
Published: May 28, 2014
jacob of Monroe, NY
Source: consumeraffairs.com

I purchased this GE Profile dishwasher last June, I paid $1,499.00 for it a
I purchased this GE Profile dishwasher last June, I paid $1,499.00 for it and have had three (3) service calls. The first one said the water is not hot enough, the second one said run the water in sink and get hot before you use the dishwasher. The tech was here again this morning and called in to tech services and was told put plates on the right side of the rack only and the dishes will get clean. Are they kidding me? I called the 800 number for customer service and was told by Dominic (rep in customer service) that they would replace the dishwasher and allow me a 40% discount on a new one because this one is working as designed. It is my understanding that the dishwasher should wash dishes, so that tells me it is not working as designed. I want a new dishwasher, preferably one that washes the dishes and not one that I have to pay an additional 60%. Are you kidding me? This is not right. I have read the reviews on this dishwasher and it seems everyone who purchased the dishwasher I have are having the same problems and it is not working as designed. Please let me know asap when the replacement dishwasher will be delivered. I will not pay an additional 60% for another. It is not right that you would keep making excuses until warranty runs out. I notified you of this problem one month after I purchased it and I have lived with this problem for almost one year and now you tell me that you will give me a discount on a new one. I have already paid for a new dishwasher and that is what I expect in return. Thank you. I expect to hear from you soon.
Published: May 17, 2012
Glenn of Powder springs, ga
Source: consumeraffairs.com

We had a GE microwave that my parents got when I was in elementary school t
We had a GE microwave that my parents got when I was in elementary school that lasted us through graduation (when I got it), and it then lasted me another 6 or 7 years after that. It was a great microwave, so we went with GE for our next one. What a mistake that was. The new one died completely less than a year after we got it (less than a year after its manufacture date at that!). The one after, one of the same make and model, lasted 3 years to the month after its manufacture date. Sorry GE, but I just do not have any interest in spending so much for so short a lifespan on your products, and its a damn shame that your quality has suffered so badly that you have lost a once-loyal customer of your brand.
Published: November 2, 2015
Shawn of Las Cruces, NM
Source: consumeraffairs.com

Has anyone experienced a plastic burning smell when the dishes are drying?
Has anyone experienced a plastic burning smell when the dishes are drying? My dishwasher is 3 years old and I wash on Light cycle which is suppose to be 45 minutes long but goes for 85 minutes. Company said to turn off circuit breaker and turn back on and it should be fine, it isnt. Last two times I used the dishwasher it wouldnt completely shut down so I had to do it manually and before I did this I could smell a plastic burning smell but there was nothing on the elements. I called for a service call but they were shut down for 4 days.
Published: October 18, 2016
Nancy of Toronto, ON
Source: consumeraffairs.com

We bought 3 GE Profile appliances in 2005 when we renovated our kitchen. We
We bought 3 GE Profile appliances in 2005 when we renovated our kitchen. We have not had much problem with the gas oven/range/stove. We have, however, had nothing but problems with the microwave (which I submitted a separate review for) and the dishwasher. Recently, a friend made some suggestions regarding the dishwasher. I then went online and watched some tutorials on troubleshooting my dishwasher problems. I tried all the new suggestions and the dishwasher worked OK the one or two times after that and then back to all the old problems: 1. We have to scour every dish until its nearly clean before loading (even though the instructions specifically stated no pre-rinsing necessary). 2. I am not sure the soap cup opens. The soap is always left caked in the cup resulting in running the dishwasher twice. We have tried all kinds of various soaps and they all do the same thing. The eco-friendly soaps are the worst. We strive to be eco-friendly, but how can we be if we are using the harshest soaps possible AND running our dishwasher twice?! Not to mention the pre-rinse scour and running water until it is 120 degrees prior to running.3. The dishwasher also leaks and is very noisy.I have read some other reviews on this product and realize our dishes are not always dry at the end. This is a non-issue for me. I dont care so much if the dishes are dry. I do prefer for them to be clean. Dishes are a task I do not prefer to do. It would be nice to have a functioning helper. I am grateful the thing hasnt caught on fire. I saw that this dishwasher currently sells for $800-$1,500. I cannot believe it. I wouldnt spend $100 on this piece of junk.
Published: June 12, 2013
C & F of Berlin, NJ
Source: consumeraffairs.com

Bought a PDT845SSJ2SS in June. Two months later, it has a leak. Good news,
Bought a PDT845SSJ2SS in June. Two months later, it has a leak. Good news, has a leak detector which shuts down the machine. Bad news is that it leaks and the leak detector worked! Called GE. We dont have an authorized service technician in your area. We will get back to you within 3-5 days. Three days later, after I had raised rain with my appliance dealer, he arranged for a local dealer to come look at the machine. Scheduled that appointment - it was Friday, and We only come to your area on Tuesdays and Thursdays. Next Tuesday is booked, so we will try for Friday. Then, someone from an organization called Platinum Services calls and says GE has assigned the ticket to them. Shes going to try to schedule a diagnostic appointment in the next 7-10 BUSINESS days. Told her to forget it (found out she was calling from Lowes and had to find a technician before she could schedule.) End of week 1. Following week, someone else from GE calls and asks if I was cancelling my service request. In the course of the conversation, she asks to confirm the model GE RANGE that I have. Kinda lost it on her... On Thursday serviceman from local dealer comes. Turns on the dishwasher - it leaks exactly where I had said it would. Need to order a part and GE will not expedite. End of week 2. Next week - crickets. Nothing, Nada, mushroom mode (in the dark and being fed BS). Called my appliance dealer today and told him to come pick up the dishwasher - says he cannot do that. I explained, “I will forfeit the money I paid - I dont want a dishwasher that leaks in the first two months of use.” He tell me GE released the part yesterday...whatever THAT means and he HOPES repairman will come next Tuesday to repair. So, I have had a new GE dishwasher for 3 months and it has only worked for 2. Be aware! I assume partial responsibility for this goat rope - I faithfully refer to Consumer Reports when purchasing appliances and electronics. I suggest you do the same... you will find GE listed AFTER BOSCH, KITCHENAID, KENMORE and others. Also, realize the GE brand is now a CHINESE company. Caveat Emptor!
Published: September 12, 2018
James of Ridgeway, SC
Source: consumeraffairs.com

My GE dishwasher was installed the first week of October, 2019. After 3 loa
My GE dishwasher was installed the first week of October, 2019. After 3 loads, the unit was no longer functioning properly. I called GE to set up a service appointment to get them to come look at the dishwasher. It ended up taking 3 different technicians, ordering 3 different parts, at 3 different appointments before the problem was fixed (or so I thought). By the time I was able to use my dishwasher again, it was already the end of December and my 30 day return window expired. It is now mid January and I am already having the same problem as before and having to go through the whole process again. Because the year warranty is only for repairs, they will not just replace the unit, and instead I will have to continue dealing with this nightmare. Obviously, I will just be replacing my unit on my own after this.... And it will not be with GE!
Published: January 14, 2020
Peyton of Maysville, MO
Source: consumeraffairs.com

We recently purchased three GE Profile stainless steel appliances for our n
We recently purchased three GE Profile stainless steel appliances for our new home. The total was somewhere around $3500. Within two weeks our $1000 dishwasher would not work. It took FOUR service calls and THREE weeks for it to finally be repaired. Now our $2000 oven (traditional/convection) has stopped working and the oven light will not go off without us tripping the breaker. Service tech not available for 5 days. I am expecting the new micro to go out any day now. All of these appliances are less than two months old. We had GE builder grade appliances in our previous home that are still running strong after 16 years. That is the reason we went with GE again. However, after the above mentioned issues with our new GE appliances, I encourage anybody who reads this to NEVER, EVER BUY ANY GE PRODUCTS AGAIN.
Published: July 12, 2016
Christy of Mckinney, TX
Source: consumeraffairs.com

Had it over 12 yrs. Never a problem. It’s a wall mount microwave. Easy to
Had it over 12 yrs. Never a problem. It’s a wall mount microwave. Easy to clean stainless steel. A bit of a pain to clean the stainless steel inside of microwave. Would recommend the microwave to people looking for one.
Published: July 8, 2019
Joyce of Winnipeg, Canada
Source: consumeraffairs.com

I bough a GE microwave oven, model JVM1740SM1SS, less than 2 years ago. The
I bough a GE microwave oven, model JVM1740SM1SS, less than 2 years ago. The keypad says that it is shorted out and needs service. It turns on randomly. I unplugged it and plugged it back in, and it will either say, service needed, keypad shorted out or press clock.GE has so many complaints about there microwaves, some that are very serious. They still claim that there are no problems with them. They have to know there are problems, but do not want to issue a recall and take a financial lose. Its only a matter of time, before something so serious happens that it will be a bigger financial lose than a recall.
Published: November 14, 2011
R.T. of Upper Marlboro, MD
Source: consumeraffairs.com

My dishwasher broke within warranty in April 2014. The warranty expired on
My dishwasher broke within warranty in April 2014. The warranty expired on April 29th, 2014. Every 2 weeks another part was ordered to the tune of 10 parts and 8 visits (unpaid work days for me). I have been in touch with consumer relations about this and I was told that this would go on forever until their techs deemed the dishwasher as unrepairable but as long as it is repairable, they will not exchange the machine. And now they are telling me (October) that I could have had another service provider fix it but I would have to pay for it because NOW it is out of warranty. I cant wait until I replace my GE refrigerator and my GE microwave because those are the last GE products that I will ever buy. I went out last month and bought another brand as I will never buy GE again. GE protocol I am told is what determines all that happened. I suggest you do the same. I am writing a long letter to GE just to get it off my chest. Nothing will be done because its another corporation all about the money!!!!
Published: October 8, 2014
rox of Corpus Christi, TX
Source: consumeraffairs.com

My GE dishwasher has clean all my dishes. Not leaving a run or mist on no d
My GE dishwasher has clean all my dishes. Not leaving a run or mist on no dish. I can set the time on when I want my dishes washed. The programming is out of this world! The cost is a great easy and inexpensive cost. My wife was very happy with the purchase. The buttons are not too big. Its very digital timing.
Published: March 19, 2020
Darnell of Hammond, IN
Source: consumeraffairs.com

Clean neat appearance over stove. Fast consistent heating. Easy heating opt
Clean neat appearance over stove. Fast consistent heating. Easy heating options. Turntable on or off. Also, love the stove top light. Cost a bit more than I thought it would, but not much more than others.
Published: July 19, 2019
Wayne of Rocky Mount, North Carolina Area, NC
Source: consumeraffairs.com

One needs to be a contortionist to replace the under light bulbs on this mi
One needs to be a contortionist to replace the under light bulbs on this microwave. It is a TERRIBLE design. Why werent the sockets placed so that the prong holes could be visible? One has to do a back-bend over the stove top and then the socket holes are still not visible. DO NOT BUY THIS MICROWAVE. DONT BUY THE STOVE EITHER. IT IS DANGEROUS. THE KNOBS TURN EASILY AND OPEN THE GAS.
Published: March 4, 2015
Martin of Chicago, IL
Source: consumeraffairs.com

I wish I had found this complaint section before I purchased my microwave.
I wish I had found this complaint section before I purchased my microwave. Bought model HVM1750DP1CC in May of 2010. Now, 3 years later, all of a sudden theres no power to the unit. The wall outlet is fine. There were no storms around here when it went out. It just seemed to fry itself! The repair/troubleshooting instructions tell you to get a licensed technician to check this and check that because of the voltage. They give you a flowchart to troubleshoot it yourself, but no pictures to go with the diagram. Sure I can check the fuses, if I knew where they are!GE - NEVER AGAIN FOR ME. Wish we still had good-valued products Made in the USA. This one is made in Malaysia. NOT WORTH IT. Time to sell the GE stock too. Their products suck and class action suits will probably follow. Kris is Pissed!
Published: May 27, 2013
K. of Shelton, CT
Source: consumeraffairs.com

I purchased a microwave in Oct 2010. It went blank and nothing works. I che
I purchased a microwave in Oct 2010. It went blank and nothing works. I checked to see if its receiving power. The power is okay. I purchased the microwave, fridge and stove at the same time. I always had confidence in GE products. Microwave should have lasted longer than less than 2 years. I didnt purchase extended warranty because of GEs reputation. Very dissatisfied customer.
Published: September 17, 2012
Ronald of Louisville, OH
Source: consumeraffairs.com

Emptying out the dishwasher I purchased in October 2016 is a cause for rage
Emptying out the dishwasher I purchased in October 2016 is a cause for rage these days. Dishes, glasses, silverware, etc...come out of any wash cycle dirtier than they went in, though I have tried everything I can think of to see if anything at all can make it better. I purchased the dishwasher from BEST BUY. Little did I know, they dont take anything back after 15 days of purchase. They promptly referred me to GE. In turn GE reps said that their warranty only covers REPAIRS for the first year. In short, sucker me who spent near to $600, is stuck with a VERY BAD product from the moment I paid for it. And there is nothing I can do about it!!! GE IS CLEARLY SCAMMING ITS TRUSTING CUSTOMERS!!! I have been robbed!!!
Published: January 11, 2017
Claudia of Santa Rosa, CA
Source: consumeraffairs.com

The GE MICROWAVE MODEL JVM6175EF1ES was manufactured in August 2015. I purc
The GE MICROWAVE MODEL JVM6175EF1ES was manufactured in August 2015. I purchased it in November of 2015, brand new from Home Depot. It was not installed until April 2016. So less than 2 years after installation it malfunctioned. (The unit brand new only has a 1 year warranty). The parts the tech replaced have a 5 year warranty. That demonstrates to me that GE does not have a lot of faith in their appliances. Aside from that I paid $375 for the repair, thats almost the price of a new microwave. But I paid since it made more sense to have a 5 year warranty on the parts instead of a 1 year with a brand new unit. I WILL NOT be buying GE products in the future due to this product defect.
Published: March 16, 2018
Michael of Davie, FL
Source: consumeraffairs.com

Worst dishwasher ever. No matter all tried it just does NOT get all off dis
Worst dishwasher ever. No matter all tried it just does NOT get all off dishes. Have to hand wash too! IS just not made to do the job. Just relying on GE reputation of the past! Made a mistake believing General Electric hype advertising. SAD.
Published: May 21, 2020
Larry of Edmond, OK
Source: consumeraffairs.com

GE Microwave was making intermittent buzzing noise 1 month after purchase.
GE Microwave was making intermittent buzzing noise 1 month after purchase. Called GE & they said they could send a tech out to check it but if they didnt find anything I would be charged a service call. I stated it would only do it once in a while so was concerned it wouldnt do it when tech was here & I would be charged so I passed on the tech. Microwave continued to make noise periodically but seemed to get less as time went on. 1 year & 10 months later it started to sound like it was arcing & shut off. Again it was periodic. Called GE. They sent a tech out & it only shut off but no arcing sound or intermittent starting & stopping. Tech stated it probably was door micro switch, but when GE called me back they said he stated it probably was circuit board. Whatever the cause it is still what I would call arcing & going off & on.GE stated They could give me a discount on a new microwave which amounted to cost of $100.00 more than I paid for it in the first place.
Published: January 13, 2014
Curt of Cave Creek, AZ
Source: consumeraffairs.com

The GE microwave that was installed in our new home (2018) stopped working
The GE microwave that was installed in our new home (2018) stopped working in June 2020, after the nuclear reactor “blew up”. Which could have been a dangerous situation. I was told by Assurant Insurance Company that it was no longer covered by the 1 year insurance policy, and if I purchased a new policy for $241.00, they would repair it or replace it. After they discovered it was not repairable, they denied the ”replace it” part and reimbursed the money for the policy. GE agreed to sell me a new microwave at a discounted price, which I agreed to. The replacement microwave was delivered damaged, in October 2020. After many calls and waiting hours on hold, service came out and said it was “not repairable“. Again, phone calls to GE Customer Relations and reexplaining the problem, I was told they did not have a microwave in stock to replace it. However, after further searching, one was found, and would be delivered. On 10/23/20, I received a phone call from the freight company that the microwave was being delivered the following day, but they had the wrong address! it was a previous address. Where that address came from is a mystery as we never had GE appliances delivered to that address. The freight company was not authorized to change the address in the system, so another call to GE. I am still waiting for a new microwave! I can’t even begin to count the number of times I have called GE, waited on hold or call-back, waited for service, and been told I have the wrong case number. I have all new GE Profile appliances, all have had service for problems. I will NEVER buy another GE appliance. Their service department and Customer Relations department is disorganized and incompetent. GE appliance are not quality products.
Published: October 26, 2020
Scott of Ocean View, DE
Source: consumeraffairs.com

I have a built-in GE microwave. It is easy to use and best of all very easy
I have a built-in GE microwave. It is easy to use and best of all very easy to clean. It is brand new and stainless steel. Looks nice on the wall above the built-in GE oven. I can easily reach it. Some built-in microwaves are too high.
Published: July 10, 2019
Arlene of Bellevue, WA
Source: consumeraffairs.com

I purchased a GE Spacemaker microwave in Jan. 2001. Shortly thereafter, the
I purchased a GE Spacemaker microwave in Jan. 2001. Shortly thereafter, the frame around the door cracked, becoming worse until in Oct 2006 I complained to GE. They sent a $75 credit towards another GE. I purchased another GE in Oct 2006. After a while, the handle became loose. Today, the handle broke off at the base where it attaches to the door, rendering the oven unusable. I dont have kids. This appliance was not abused. I see in looking through the comments that other consumers have had similar problems which would suggest a product defect. My next microwave will not be a GE.
Published: July 10, 2012
Linda of Columbus, NJ
Source: consumeraffairs.com

Have owned, installed, and repaired many dishwashers throughout the years a
Have owned, installed, and repaired many dishwashers throughout the years at various houses. This GE unit is by far worst dishwasher that I have ever had the displeasure to install and operate, and it replaces a Kitchen Aid unit that started a fire, see **. Specifically the GE unit had the control panel break off due to misalignment, requiring repair, the drain bulkhead fitting was poorly designed and caused a leak, requiring repair, the water solenoid valve failed in the 2nd year, and finally the door does not lock closed without significant care and attention to alignment and requires many attempts to lock closed for the start of cycle. This is the worst and I cant wait to pull it out and replace it.
Published: March 12, 2020
Luke of Norristown, Pennsylvania
Source: consumeraffairs.com

I have a GE dishwasher installed by our builder. It is 6 yrs. old and for 6
I have a GE dishwasher installed by our builder. It is 6 yrs. old and for 6 yrs. it has been a problem. I already had it serviced in last years recall and now I get another notice. It is located close to our TV viewing area. and is so noisy. I hate to run it when we are watching TV. I would never buy another GE. We are also having problem with our GE double oven. I ruined several holiday dinners before realizing the temperature was 75 degrees where it should be. A replacement part is almost a $1,000. I would never ever buy another GE appliance.
Published: February 2, 2013
Mary of Wadsworth, IL
Source: consumeraffairs.com

Dishwasher lasted just little over a year when it broke down first time. Po
Dishwasher lasted just little over a year when it broke down first time. Power switch made out soft plastic jammed up. Next cheaply made door close switch cracked. Part prices are average price. Because poor quality, I predict replacing this within 3-5 years.
Published: February 18, 2021
Peter of Hillsboro, Oregon
Source: consumeraffairs.com

We purchased a new GE dishwasher from The Brick, after three washes it leak
We purchased a new GE dishwasher from The Brick, after three washes it leaked all over our new hardwood floors. I called The Brick and they said it was GEs problem. I called GE and they sent out a repairman who told us it was a broken seal on the pump and that this dishwasher is discontinued and he cant get the part. So, that would mean GE would have to replace our washer with a new one! We went back to The Brick and told them we did not want the GE washer and wanted to replace it with another brand as we were within the thirty day guarantee. No apology or well pay for the damage to your floor (floor is warped underneath) and guess what Im still waiting for a call back from GE!! Dont buy anything made by GE. You will regret it! As well, I will not be shopping at The Brick anymore.
Published: August 17, 2015
Teri of St Catharines, ON
Source: consumeraffairs.com

My 5 years old over the range GE Microwave Oven in my old house had a keypa
My 5 years old over the range GE Microwave Oven in my old house had a keypad malfunction. I replaced that oven with a different brand. This time, my 2 years old GE profile microwave in my new house has the same keypad shorted like other users posted. I was hesitating to buy this brand at the time. But the look and match with other appliances, plus the good deal from vendor, I gave it another try. I made a terrible mistake. No more GE appliances for me.
Published: August 23, 2011
Joseph of Oklahoma City, OK
Source: consumeraffairs.com

I bought a microwave Model JVM316RF3SS on 6/12/16 from Best Buy. Here is th
I bought a microwave Model JVM316RF3SS on 6/12/16 from Best Buy. Here is the serial number GG242212A. This thing is tripping the circuit breaker, it is intermittent. I had been buying GE for the house because the stuff would last or they would stand behind their products. Looks like times have changed, I called yesterday to the customer service and the only thing I was offered was a song and dance. If you are to consider buying a GE product, think about it again. This microwave is only a year and a half, to have a tech service guy come out and look at it, it is was priced out at $97-108 for a visit and then parts and time will be added in additional to this visit price.They have priced this repair out to be cheaper to just replace it. My washer is making excessive pump motor bearing noise during the high spin cycle, this is two years old. Looks like GE is building crap. My background is a mechanical technician for over thirty years, building products that are to be used in the household should be built to last not become a disposable item like a cigarette lighter. Good job GE for joining the other substandard products being built. Must be outsourcing this to a foreign country like everything else. With the model and serial number GE you can call me if you have ANY questions.
Published: January 6, 2018
Roger of Downers Grove, IL
Source: consumeraffairs.com

Our GE Dishwasher is about 22 months old and is now not starting. GEs custo
Our GE Dishwasher is about 22 months old and is now not starting. GEs customer care is a joke. All they want to do is send a repair person with a $110 fee just to come and the person making the appointment refused to tell what the labor rate would apply once they got there. They offered zero help as far as troubleshooting. I called a local repairman and was told he has had many similar issues with newer GE Dishwashers. We are throwing parts at the problem now trying to get it running. He also said repair assistance or troubleshooting from GE is very poor. Really not pleased having a less than 2 yr old major appliance not working. GE means JUNK to me.
Published: April 24, 2019
Dave of Clarkston, MI
Source: consumeraffairs.com

Purchased an entire kitchen suite of GE appliances. Almost instantly the fr
Purchased an entire kitchen suite of GE appliances. Almost instantly the fridge started making loud noises which the repairman told me was normal. LOUD AND OBNOXIOUS. I wear earplugs in my house to avoid the noise! Secondly, the dishwasher started leaking and the warranty company is refusing to honor the warranty so Ive been hand washing dishes since August! They also refuse to refund the extended warranty fee. Currently filing a protest with consumer fraud. STAY AWAY FROM GE, isnt that a shame! THEIR PRODUCTS ARE JUNK!
Published: January 24, 2019
Bobbi of Arvada, CO
Source: consumeraffairs.com

We have a full size counter top GE microwave. It is about 3 years old and t
We have a full size counter top GE microwave. It is about 3 years old and there have been no problems. Our last microwave was also a GE and it lasted about 15 years before it started to suffer from occasional electrical arcing inside, while in use. We simply stopped using it and after reviewing all models, chose to buy another GE and it has been great. We have an over the range micro at our summer home - a Frigidaire and not as good. Our research shows it will likely fail long before the GE.
Published: December 14, 2015
Doug of Brampton, ON
Source: consumeraffairs.com

Unit is only 7 years old and not greatly used (only two adults who dont use
Unit is only 7 years old and not greatly used (only two adults who dont use it much)… Purchased as part of package including GE refrigerator, range and dishwasher (already got rid of refrigerator, as parts kept breaking and unit had other chronic problems). I turned the microwave on to make popcorn - it immediately made a terrible noise and filled with smoke with an electrical smell. Unplugged the unit and contacted GE Repair. When I described what happened, I was transferred immediately to their safety unit because of the nature of the problem. A GE technician arrived today and almost immediately diagnosed the problem: a metal component that directs the waves of the microwave generation tube had burned out, and by federal regulation, he claimed, cannot be repaired - the whole appliance must be trashed and replaced. Once again, I have experienced GEs poorly engineered products that appear to be designed to fail in a relatively short time. Can you spell planned obsolescence? (No photo provided, as there is no external visual damage).
Published: September 13, 2013
Anthony of West Bloomfield, MI
Source: consumeraffairs.com

Our Profile over-the-range microwave failed after 2 years. (Warranty was fo
Our Profile over-the-range microwave failed after 2 years. (Warranty was for one year!) One day it suddenly died. The repairman ($100) said repeated twisting of the wire from the oven to the door (which contains all the electronics) is inevitable with opening and closing. The wire often breaks within its insulation: a bad design fault. No question of replacing the wire; we would have to order a new door, for nearly $400 plus $200 for installation, which requires 2 service technicians. This is more than the cost of a new OTR microwave. He advised us to get one with the controls beside, not in the door. Unfortunately GE is the only company that makes a microwave in the same colour as our range.
Published: August 25, 2020
John of St Thomas, ON
Source: consumeraffairs.com

All GE kitchen appliances delivered on time, but the dishwasher has been a
All GE kitchen appliances delivered on time, but the dishwasher has been a nightmare. Started leaking right away, called GE and they couldnt come back out for 3 whole days after installing it, which ended up being a work day - so had to miss work to wait all day when he didnt come until 5 pm. Tried to make us pay for the service - we havent even used the dishwasher and they think we are going to pay them to come out fix their mistake, also under a 1 year warranty. Tech guy came out ran some computer test - didnt even look at the dishwasher or underneath. Test was good, we asked him to stay a few extra minutes and he said thats not his job. Leaked again. GE argued that we didnt get it installed by them, which was a lie. Same tech guy came out again, on a workday Again so missed work - finally figured out what was wrong, ordered the part. The part wasnt coming in for another week. So we Waited Another week without a dishwasher.When that day came We again missed work because they said between 1-5 and didnt even show up. GE tried to say the part wasnt in but we were holding the part when we asked where they were. Infuriating at that point already missed so much work days and GE employees couldnt even do their job. GE rescheduled the appointment without even telling us. Had to wait another week until they finally came out and fixed the dishwasher. Now almost a month after they delivered the appliances, I received a charge and didnt not even email to let us know we were being charged. Horrible experience with GE and will never ever buy from them again.
Published: October 27, 2017
E. of Louisville, KY
Source: consumeraffairs.com

Im very upset with my self for not doing the proper research on this produc
Im very upset with my self for not doing the proper research on this product. I cant imagine a dishwasher being worse than this one. From day one, it never cleaned; half the dishes are always dirty. Some soaps work better than others. Still dirty dishes. We paid nearly $1000 for this machine, and once again, it has backed up. I will do my research next time. Their service department tried to tell me it was because it needed to be cleaned. GE never again! I have a busy family, and there is nothing more frustrating than having a dishwasher and not being able to use it.
Published: March 7, 2012
Susan of Innisfil, ON
Source: consumeraffairs.com

We bought a GE cafe series microwave (model/serial number: pnm919sf1ss/gd23
We bought a GE cafe series microwave (model/serial number: pnm919sf1ss/gd235771b) and 4 months later it ceased to function. We just had a remodel and for the first time had an expensive, over the oven microwave and were very excited. Unfortunately, unlike the 2 cheap microwaves weve purchased in the last 36 years, this one we had used for 3 months total, developed problems. The motor seemed to surge and then it would go off. Half an hour later it came back on but would only work for about 5 minutes at a time. I called GE and they arranged for a local company to come take a look. They insisted on a 4 hour window and fortunately my husband is retired so he could be there. The repairman came and didnt have a clue as to what was wrong. He called his boss who talked him through diagnostics. After an hour he left, saying hed be back in a week with some new parts. Again we had to wait the 4 hour window. He came in and we were on pins and needles hoping he wouldnt scratch our cabinets as he took the unit down. He replaced the microwave component and when he left it worked. Two days later it again died. I called the repair people and they told me I had to call GE to get permission for another attempt at repair. I called GE and they said I had to call customer service to file a report. They told me I had to make an appointment for a technician to come out to see if the microwave could be repaired. Really??? The technician would try to repair it again or decide it couldnt be repaired and needed to be replaced. Like we have nothing better to do than wait for these repair people who have no clue as to how to repair the microwave. Every time they take down the microwave they risk ruining our cabinets. It was so unhelpful. I am really disappointed in GE customer service. We had to go out and buy a microwave to use while we were waiting for the repair. They obviously dont care that we cant use their expensive product. Our replacement microwave was $40 from Walmart and works beautifully. We finally complained to our WONDERFUL contractor who originally purchased the microwave for us and he is replacing it with a new one. He was appalled by GEs treatment. He takes note of appliances that are crap so he can warn customers. I thought I was buying from a reputable company and thinking we were getting a great and special product. Too bad.
Published: January 29, 2015
marilyn of Davis, CA
Source: consumeraffairs.com

I purchased a stainless steel GE dishwasher for $508.68 since I remodeled m
I purchased a stainless steel GE dishwasher for $508.68 since I remodeled my kitchen October 2016, I contacted GE in March 2017 because the stainless steel on the dishwasher door started to have rust spots, they sent a technician to look at it, they told me that they cannot replace it because the aesthetic warranty is only good for 30 days. They authorized the technician to replace the door, however I have the same issue with the new door, and also the dishwasher stopped working. I contacted them again. The technician was able to fix the dishwasher, but as far as the stains on the door they told me thats an aesthetic issue. They cant do anything about it. I called the consumer relations department. I spoke with CIARA GE case # **. They offered me a small discount and I have to come up with $400.00 to buy a new dishwasher.I feel that a good business should always stand behind its products. The dishwasher obviously is defective, they sold me an appliance that supposed to be stainless steel but its something else, the right thing for GE to do is to exchange the defective product for the right one. I am very frustrated that in less than a year I have to spend over $900.00 for a dishwasher. I am great customer for GE, I remodeled my kitchen, I purchased a GE refrigerator, cooktop, oven, kitchen hood, microwave and dishwasher, I think I deserve better than a small discount for a defective product.
Published: December 4, 2017
Suzette of Sunrise, FL
Source: consumeraffairs.com

We sent the rebate form in, and they denied our claim. It was for a dishwas
We sent the rebate form in, and they denied our claim. It was for a dishwasher that was recalled. We had to buy another one and only received $100 for the rebate after having to spend $500 on a dishwasher, but the rebate was denied! Unbelievable. We have written GE and the FTC with no response.
Published: March 27, 2013
Kristen of Mission Viejo, CA
Source: consumeraffairs.com

The door handle broke on GE Advantium microwave. My complaint is that the p
The door handle broke on GE Advantium microwave. My complaint is that the plastic handle costs $103.00 just for the part. That is ridiculous! The unit is 6 years old so I dont expect it to be free. I just dont understand how they can justify that much.
Published: September 12, 2011
Phil of Gainesville, GA
Source: consumeraffairs.com

After about 5 months of owning the unit (GE dishwasher model GDT580SGFBB),
After about 5 months of owning the unit (GE dishwasher model GDT580SGFBB), the door latch sensor became defective and discontinued the wash cycle up to 6 times every use. I contacted the GE warranty department. Their consumer relations advocates treated me as subhuman. I never felt like a valued customer, my concerns and my time were never a priority. Instead I became a part of their research and development program while beta testing a defective product.After 6 months of futile repairs requiring multiple technician visits I was exasperated. I had submitted 4 separate warranty claims that often were mysteriously closed without my knowledge. I finally contacted the original retailer, Home Depot, and shared my experience. They catered to me even though it was well past the 90-day store policy. They gave me a credit for the purchase price so I could choose a replacement. Since I dont want to touch another GE appliance with a 10-ft pole, I chose another brand. Shortly thereafter I received a call from GEs Escalated Issues department offering to replace the unit. Evidently that lit a fire under them. But it was too late, my patience with GE has been exhausted. If this is the way GE wants to run their business, then it will be a fast-track way to dig their own grave.
Published: March 1, 2015
John of Bend, OR
Source: consumeraffairs.com

I thought there were food particles between the glass plate and the ring. W
I thought there were food particles between the glass plate and the ring. When I took out the plate, I saw that the paint had bubbled and was peeling off the bottom of the microwave. Extremely unhappy with this. Ive had hand-me-down off brand microwaves that lasted much long than this GE and with NO PROBLEMS until they just rolled over and died. I have all GE appliances in my kitchen and have to say that Ill never buy GE again. Electric stove is a problem, dishwasher a problem. Refrigerator was a problem (when it was new! it was fixed and thankfully is still running well).
Published: July 30, 2014
Jackie of Somerset, NJ
Source: consumeraffairs.com

A GE water heater was installed in our new home in 1962. As of today, Novem
A GE water heater was installed in our new home in 1962. As of today, November 2, 2014, we are pleased to let you know it is still in excellent working condition 52 years later... Way to go GE... The only update we changed lower element twice in 52 years!!!
Published: November 3, 2015
Larry of Concord, NC
Source: consumeraffairs.com

Last fall, we updated our kitchen counters to quartz, and the Jenn-Air to a
Last fall, we updated our kitchen counters to quartz, and the Jenn-Air to a GE induction cooktop. While it is indeed pricey, the joy of cooking is not overstated here. The quick heat up, the ease of controlling the heat more precisely, and the easy clean up makes this unit well worth it. I love it!
Published: November 14, 2017
BARBARA of Reston, VA
Source: consumeraffairs.com

We bought a brand new GE dishwasher from our local hardware store on Black
We bought a brand new GE dishwasher from our local hardware store on Black Friday. It was $600 dishwasher on sale. It was installed on December 5th, it broke on December 6th, and we had a repair man come out to take a look at it. To be fair, the local hardware store did ask if we wanted to replace (2 week wait time) or repair (2 day wait time) it. Since it was a bolt that was severed (by opening the door to the machine, mind you), we figured it would be an easy fix. The first technician who visited said, Yeah, its broken. I have to order a new bolt and then come back out in a week to fix it. And oh, by the way, Ill have to drill a new hole for it too. Thats when I called GE customer service to request a new product. But since my 48 hour window had passed, and we opted to have it fixed, it was keep it or ask our local hardware store to replace it at their expense. I bit the bullet and just had it repaired. Now, less than 2 months later, the technician has been at our house three times. He’s soon to have a fourth visit because we need a new dispense modulator. After speaking with customer service several more times, and with a not very nice lady in the Chairmans office, I still have a defective product. Oh, did I mention that Im paid hourly and have now taken off 13 hours? So what’s the use of that $600 dishwasher that we bought? Its been out of commission for more than 2 weeks, in less than 2 months, and has now cost us $900. Thanks, GE! We’re so glad to see you stand behind your product.
Published: February 5, 2013
Miranda of Cranberry Twp, PA
Source: consumeraffairs.com

I bought a brand new house and it came with the set of GE profile appliance
I bought a brand new house and it came with the set of GE profile appliances in 10/2009. In November of this year, it came on for one minute on its own and then popped and indicated a circuit board failure. The inside of the microwave was extremely hot and there was obviously an electrical short. This could have burned down my house! My fiance replaced the circuit board at a cost of $125. I negotiated from the service department that supplied all my builders appliances. This week it happened again. This time, there was a cup of coffee in the microwave and it boiled in the minute before the microwave fried itself! I cant believe that GE still has this product on the market! Any product on the market! I have to replace this because I cant sleep thinking its going to catch my house on fire. Are there no ethics anywhere?
Published: March 21, 2012
Jo of ., OK
Source: consumeraffairs.com

The microwave oven that I’ve been using works real well and it’s not th
The microwave oven that I’ve been using works real well and it’s not that expensive. It’s also a convection oven at the same time. The only reason I didn’t give it a 5 is, I rarely give that high # to anything with rare exceptions.
Published: July 11, 2019
Eveline of Liberty Hill, Texas
Source: consumeraffairs.com

My GE over the range Microwave has broken about 4 times in a years time. My
My GE over the range Microwave has broken about 4 times in a years time. My warranty company American Home Shield (AHS) has decided that instead of replacing this piece of garbage, its somehow worth it to keep on fixing it, which is apparently their MO for all their customers but I digress. After the latest breakdown (microwave lost power completely), I was referred by AHS to GE Appliance repair. Thus began the nightmare. The tech that showed up was incompetent at best. He showed up, looked at me, made a grouchy face and proceeded to walk in the kitchen with an attitude like he was doing us this massive favor. He opened the microwave door, closed it, opened his computer and ordered 10 (yes 10) different part. Again, he literally just opened and closed the door - did not disassemble to see what part was actually messed up. No diagnosis done of any kind. He scheduled to come out the week after that - didnt show up because I missed his phone call. Btw, I called him back pretty immediately and he didnt pick up. After being on hold for about 35 mins (which is clearly the GE standard hold time), they tell me the guy has left the area and they need to reschedule me for a week later. The day before the 2nd appointment, they called to reconfirm and then the morning of, I called, stayed on the standard 35-40 min hold and reconfirmed he was still coming and was told he was on his way. Well, the appointment time came and went and he failed to show up YET again so I called to ask wtf happened. They said he didnt come because I canceled the appointment thru an automated call. This time the idiot didnt call me like they always do. I asked for proof of this alleged automated call that was placed to me and they said no call record exist and so while it seemed like a system glitch, the tech already left the area and theyd need to reschedule it. I told them, No, thank you. Got a local repair company to come out the very next day. Turns out, out of the 10 parts that idiot tech had ordered, only 4 had arrived while the invoice still showed 10 being shipped. Let me clarify this: All these issues stem from GEs entire company: From manufacturing crappy products to HR hiring incompetent techs to customer service being absolutely nightmarish to supply chain not sending parts that are being ordered. And if you can somehow get their alleged consumer advocate department on the phone after a 40 min hold time, they dont give a crap either. All these employees MUST hate GE to drive customers away as far as possible. I own a business and I will never ever EVER buy GE again.
Published: December 2, 2016
Azher of Bensalem, PA
Source: consumeraffairs.com

My life partner/bf moved into a semi flipped 10 yr old home. Every single a
My life partner/bf moved into a semi flipped 10 yr old home. Every single appliance required to be replaced, everything from refrigerator, stove/oven, to dishwasher. We researched every appliance we purchased, a lot of time and effort along with reviews from various reputable reviewers, pointed us to the GE GDT DISHWASHER. Who can go wrong with three tier washing amongst jetted water bottle washers?After a 1 1/2 yrs in the top spinner completely separated from its housing. We googled the problem, GE said it was a faulty design, yet no recall. The door lock began to fail, googled the repair fix, another fault design, yet again no recall. Upper plastic door trim broke in half, solution, replace the entire console. Guess what? My solution here on out is to not buy GE products. If two years is all you get with a GE product, I am out! Done with your products that once lasted 10 to 15 years. The fact that have to research another DISHWASHER, absolutely pisses me off. I dare you GE to win me back!
Published: June 28, 2017
Janna of Maricopa, AZ
Source: consumeraffairs.com

GE Stainless Steel Profile Dishwasher - My dishwasher is about 5 years old.
GE Stainless Steel Profile Dishwasher - My dishwasher is about 5 years old. Two years ago, we noticed that the gaskets, both around the tub and on the bottom of the door, were becoming gummy and rippling. We were hoping to make it another couple of years before buying a new dishwasher, but a couple of week ago, the top arm fell off because the gasket was so degraded. We ordered the appropriate parts and were only able to replace the top-arm gasket and the tub gasket. We had to call an authorized GE repairman, specifically RC Appliance in Sparks, NV. When he tried to get the gasket out, his hands turned black from the rubber. After about an hour of trying to get the new gasket installed, he had to use his pliers to crimp the gasket in place leaving large dents along the bottom edge of the door. He said the factory had crimped the old gasket in place at the factory from the other side. I am extremely unhappy about the workmanship and the fact that the gaskets did not last a reasonable time. I dont want to seek an attorney, but would rather GE contact me to discuss what must be done.
Published: March 13, 2013
Vicki of Sparks, NV
Source: consumeraffairs.com

I rarely use it. I know to avoid too close to the signals produced in the m
I rarely use it. I know to avoid too close to the signals produced in the microwave and use it only about once a month.
Published: December 14, 2015
Marvin of St. Joseph, Michigan
Source: consumeraffairs.com

Very heavy to mount above a stove, not enough watts. The model I have is 90
Very heavy to mount above a stove, not enough watts. The model I have is 900 watts, too many options for cooking different foods, not many parts are available to make a repair on any of the GE microwaves, I would not recommend purchasing a GE.
Published: July 17, 2019
Raymond of Washington, Pennsylvania
Source: consumeraffairs.com

GE profile microwave magnetron burned out after 2 years. Part is supposed t
GE profile microwave magnetron burned out after 2 years. Part is supposed to be under warranty, but repair is not. There are no service centers in my area. GE wont just send me the part, or let me send them my old part.
Published: July 29, 2011
Steve of Bayfield, CO
Source: consumeraffairs.com

We had to replace our dishwasher a few months ago and we got a GE Dishwashe
We had to replace our dishwasher a few months ago and we got a GE Dishwasher and we could not be happier. This unit cleans so much better and seems to take a lot less time to do a full load. I would recommend GE to my family and friends.
Published: February 11, 2021
Andy of Salisbury, MD
Source: consumeraffairs.com

While using GE dishwasher there is feeling of easiness with less efforts. E
While using GE dishwasher there is feeling of easiness with less efforts. Even kids can use at home while alone to keep their utensils clean. To learn clean habit from home is good for kids to be a gentlemen in society.
Published: March 10, 2020
Bs of New Delhi, New Delhi
Source: consumeraffairs.com

From these posts, Ive seen people saying that they couldnt trust GE America
From these posts, Ive seen people saying that they couldnt trust GE American-made anymore. Our microwave oven was made in Malaysia, but GEs home office appears to be in Louisville, Kentucky. Our problem: peeling paint on the door and upper part of our 2009 GE #JES1451DN1WW oven. As a cancer survivor of 8 years, my antenna goes up with any defaults such as this. On a common sense scale this should never be happening. I was very sad to see no recalls on these items Ive been reading about and am frankly scared to use this microwave. Shame on you, GE.
Published: November 24, 2012
Dianne of Washington, Nc, NC
Source: consumeraffairs.com

We purchased a complete kitchen of Profile appliances. Everything is fine e
We purchased a complete kitchen of Profile appliances. Everything is fine except dishwasher! The first one didnt clean food and left scum on everything... The company sent service several times replacing many parts.... finally gave us a new one... It still doesnt clean. It will not remove peanut butter, avocado, and my teacups are perpetually stained dark brown. My old dishwasher, Kenmore, left my dishes sparkling... no matter what was on them, plus I didnt have to run my kitchen sink to get hot water first! I will not use GE in my next house which will be built in about 3-4 years.
Published: May 18, 2014
Celeste of Ozark, MO
Source: consumeraffairs.com

GE dishwasher caught fire - not part of recall. I arrived home for lunch to
GE dishwasher caught fire - not part of recall. I arrived home for lunch to find smoke alarm going off and kitchen hot and hazy. Determined it was dishwasher and opened to thick black smoke pouring out. Heat so extreme cups/dishes and racks and spinning thing on bottom had melted and adhered to elements, each other and bottom. Parts of the dishwasher itself are warped (steel!). Granite countertops too hot to touch and wood cabinetry surrounding it darkened. Dont know the extent of that damage yet. Thank GOD I came home for lunch- I normally do not. I truly believe our house would have been on fire.
Published: October 11, 2016
Anthony of Destin, FL
Source: consumeraffairs.com

The microwave has done its job for the last 15 years and is still going str
The microwave has done its job for the last 15 years and is still going strong. It isnt perfect, but it serves me well. The microwave is fine, but I am no longer a fan of GE products. The design of their stove makes it difficult to clean. I had to pick their dishwasher because it was the only one with the right dimensions. It does a terrible job cleaning the dishes.
Published: January 16, 2017
Beverly of Douglaston, New York
Source: consumeraffairs.com

I replaced a GE JEM25 microwave when the Magnetron gave up with a PEM31DWW
I replaced a GE JEM25 microwave when the Magnetron gave up with a PEM31DWW unit. Within 14 months the paint on the ceiling of the oven started flaking off. Contacted GE and they offered to sell me another oven for $166. After reading all the negative reviews on this site, I dont think I will ever buy another GE product.
Published: February 21, 2014
Rob of South Lake Tahoe, CA
Source: consumeraffairs.com

GE microwaves are crap. In fact its not restricted to microwaves. Its their
GE microwaves are crap. In fact its not restricted to microwaves. Its their ENTIRE line of appliances. They team up with other grade e or f manufacturers for appliances (ie: LG, Samsung) and ANY GE appliance is almost guaranteed to fail prematurely. I see all these comments bucking Malaysia and in all reality the fact remains that Malaysia makes damn good stuff (think SONY). But it is the COMPANIES that build the products and how much theyre getting paid that factors quality. No doubt that GE is using the bottom dweller rejected off the assembly line parts to build their units. Most are Chinese garbage. China also builds some very reliable products but as the saying goes dumb American will buy anything. They save the best for them and sell us the crap.It is the lowest grade of those already should have been scrapped at the factory parts that GE passes off as quality and they do a good job at showing it. A cheap 30 dollar China made Emerson microwave made by Daewoo (Korean company that actually is decent) lasts longer and takes a hell of a beating compared to the overpriced rejected junk we call GE. The GE ac units are another classic example of pure garbage. Sadly the older GE works forever. That should sum it up. Why didnt the GE executives while visiting Thomas Edisons grave make every effort to step away from his grave and not stand upon it? Because Thomas Edison would pull them under.
Published: October 29, 2013
Geoffrey of Breckenridge, MN
Source: consumeraffairs.com

My dishwasher is very quiet and effective in its use. I am very pleased wit
My dishwasher is very quiet and effective in its use. I am very pleased with my unit as I saves water and power when in use. It also cleans very well and smells good as it drains completely. General Electric is very reliable and outstanding company and is made in the USA.
Published: March 8, 2020
Keith of Miami, FL
Source: consumeraffairs.com

Model # JVM1752SP2SS - I have had my microwave for 5 years. Last night, my
Model # JVM1752SP2SS - I have had my microwave for 5 years. Last night, my husband and I started smelling burning rubber. That lasted about 20-25 minutes. Then my husband heard a strange sound coming from the kitchen. When he went to investigate, he found our microwave on fire.
Published: August 7, 2018
Shelly of Davison, MI
Source: consumeraffairs.com

I like microwaves to a point. If my wife puts my dinner the refrigerator an
I like microwaves to a point. If my wife puts my dinner the refrigerator and I take it out and put it into the microwave if the dinner has let’s say pork chops, mashed potatoes, peas everything gets cooked except the mashed potatoes. They’re always cold and sometimes the peas will pop. There’s never a good medium for all foods at once and if you have any bread or biscuits you have to take it out after 15 seconds. The same goes with turkey cranberry stuffing and other things that go on the plate at Thanksgiving. Some stuff gets very hot. Some stuff stays cold.
Published: July 3, 2019
Charled of Rockville, MD
Source: consumeraffairs.com

Two years ago, after owning a GE JVM1490 microwave-convection oven (over th
Two years ago, after owning a GE JVM1490 microwave-convection oven (over the stove) for three years, the door handle broke.Let me clarify that I worked for GE first as an engineer, later as manager, for 20 years including 6 in Major Appliances. I am ashamed of what I am reading how GE is treating customers today.I am perfectly capable of replacing the handle myself if I am provided the complete and correct assembly drawings and/or instructions. GE refused to provide me anything when I requested them. The scant drawings and instructions I found online are insufficient. As a matter of fact, the design is so poor that removing the internal bezel, which you must do to reach the handle fasteners, forces you to break the mounting tabs, requiring replacement of this part plus the handle. This was confirmed by the parts store I visited.However, even after removing the bezel, neither I nor another ex-GE appliance engineer could figure out the access to the fasteners. I have glued the handle three times using epoxy and Cyanoacrylate (super glue), but it has broken off a fourth time. I will figure out a way of fixing it before I pay GE close to $100 for both the handle and bezel. And if I replace the appliance, you can be sure it will not be GE.GE should be ashamed of the poor design and deplorable customer service they are giving now. How things have changed!My suggestion is that all with this problem post name and phone number of GE customer service personnel they spoke with.
Published: August 26, 2011
Eduardo of Orlando, FL
Source: consumeraffairs.com

Now out of warranty, my 4-year-old microwave (sadly, the top oven of a doub
Now out of warranty, my 4-year-old microwave (sadly, the top oven of a double wall oven), has been flaking and peeling paint. It is totally unsafe and unusable.
Published: April 1, 2013
Sydney of Ca, ca
Source: consumeraffairs.com

Dishwasher is 3 months old and today is the first time it has worked! GE ha
Dishwasher is 3 months old and today is the first time it has worked! GE has sent repair techs 3 times and finally today the unit was temporarily repaired with electrical tape attached to the brand new door latch. The door latch is cheap plastic and has a manufacturer design defect of being too small to properly engage the unit when the door closes, thus not allowing the cycles to start just a series of beeps. No other manufacturer uses a cheap plastic door latch designed like this but GE! Piece of crap, dont buy it!
Published: November 18, 2017
Brilliant of Euharlee, GA
Source: consumeraffairs.com

We have a GE profile dishwasher for about 14 months. I just found out last
We have a GE profile dishwasher for about 14 months. I just found out last week that its out of warranty and that the 2 circuit boards inside are bad so the tech came out and didnt have a replacement board on his truck saying they never have problems with this dishwasher so hell order this part and be shipped to my house. He would install it on the following Thursday so Im sitting here waiting for service. I finally called to find out that GE decided that it is going to be repaired on Friday. I did not know this of course so I asked for a supervisor. I was put on hold with no answers, finally hung up in disgust.
Published: February 23, 2012
Theo of Philadelphia, pa
Source: consumeraffairs.com

Visa MasterCard

Site Secured By The Website Guardian
TOP