If you're looking for help fixing your Hisense Television, look no further! Our comprehensive Hisense Television error code guide will explain common issues, provide tips, and show you how to read your model's error codes.

CODE: Red Light Blinks 2 Times
Hisense TV red light blinks 2 times is an error indicating that the TV hardware is malfunctioning. This error code signifies an issue in the TV’s circuit because of an incorrect voltage supply on the main chip. 
In some cases, defective TV’s backlight, degradation in power supply, and severe internal damage are some of the major reasons for flashing red light 2 times. Now, let’s get to the troubleshooting steps for this Hisense tv power light blinking code: 
Solutions:
First, turn off your TV.
Unplug the TV’s power code from the wall outlet.
Do a power cycle on your Hisense TV. Leave the TV unplugged for about 30 seconds.
After that while, plug the tv’s cord back into a different outlet.
Then, reset your TV into factory default settings.
To troubleshoot the bad power supply, you may need to inspect the TV’s back panel and check out the mainboard. There may be a bad capacitor that is the culprit. Contact a professional if there is still red light flashing after power cycling.

CODE: Red Light Blinks 3 Times
Hisense TV red light blinks 3 times is a direct indication of the damage to the TV’s internal circuit board. Most likely, there may have been blown capacitors in the mainboard.
Also, because of overvoltage or overcurrent supply, burnt-out lamps in the panel lead to the same error code. Anyway, follow the below instructions to fix the TV’s error code based on the number of 3 times.
Solutions:
A hard reset is an effective fix in the case of any type of blinking code on Hisense TV. So, start by power cycling your TV.
Unplug the TV and leave the TV disconnected from the power source for about 30-40 seconds. 
Meanwhile, press and hold the power button for a little while and then turn back on the TV again.
You will need to examine the TV’s motherboard if even now, you are experiencing the blinking code. 
Disconnect the back panel and check out the lamp first.
Ensure well-working capacitors on the mainboard. 
Replace the bad lamps if there have an incorrect voltage supply.
Or, it will be better to replace the entire strip to fix the issue.

CODE: Red Light Blinks 5 Times
Hisense TV red light flashing 5 times happens due to a faulty cable connection. Also, if there have sort of glitch on the HDMI cable connection or an issue with the power supply occurs, there appears the same blinking code. Sometimes, the TV gets an issue with the power board, or there may have a fault with your backlight LEDs behind this error code.
Solutions:
As usual, start troubleshooting by doing a power cycle on your TV.
Press and hold down the minus volume (-) button and menu button simultaneously. 
If that doesn’t prove well, inspect the power board.
Replace the bad capacitors.
Examine the backlight LED test using a flashlight. Replace the defective backlight.
Finally, check out all the cable connections and ports.
Replace the faulty HDMI cables.

CODE: Red Light Blinks 6 Times
If you are struggling with the red light blinking 6 times on your Hisense TV, be sure your TV has detected some system error. There have been some major reasons for this blinking error. Note down the following causes first before moving to the troubleshooting steps:
TV is getting overheating
Blocked TV vents by debris
Outdated software
Glitches on mainboard or inverter boards
Burnt LED Strip inside panel
Defective power board
Fault IR sensor
Solutions:
First, restart your TV.
It will be better to do a power cycle on your TV in order to give relaxation to its functions.
Disconnect your TV from the power strip or surge protector.
Connect the TV directly to the wall outlet.
Remove all the connected devices with the TV.
Clean out the TV vents and ensure block-free vents.
Factory reset your TV.
Update the TV’s firmware with the latest version.
If still there have same blinking code, check the motherboard and IR sensor.
Replace the faulty IR sensor and motherboard.

CODE: Red Light Blinks 7 Times
Hisense TV red light blinks 7 times in an error indication of a faulty circuit stage inside of the TV. In most cases, this error code occurs due to a defective inverter board or LED backlight. Sometimes, TV gets overheated and blows out the capacitors. Then, the TV flashes red light 7 times.
Solutions:
Test the backlight of the TV first.
Replace the defective backlight.
Remove the back panel of the TV and check out the capacitors.
If you notice a domed or swollen top on the capacitors, be sure it is the culprit. Replace the bad capacitors.
Besides all these, ensure that you are using a well-working remote control.

CODE: Red Light Blinks 8 Times
Hisense tv red light blinking 8 times is the fault indication of a hardware fault. Some other responsive factors are a bad power supply board, a faulty circuit section, and hitches on the fluent power supply on the mainboard.
Also, unstable cable connections and faulty wiring connections are highly responsible for this blink code. Don’t worry. We are providing all the corrective approaches to fix this major issue on your Hisense TV.
Solutions:
First, unplug your TV from the power source connection.
Do a hard reset on your TV by unplugging it for about 1 hour.
Meanwhile, press the power button for about 60 seconds.
After hard resetting, check out all the wiring and cable connections of the cable.
Replace the cracked or defective cables.
If needed, you will have to inspect the mainboard and verify the capacitor condition.

CODE: Red Light Blinks 10 Times
Hisense TV red light blinking 10 times is an error indication of an incorrect voltage supply into the TV. Sometimes, the red light starts flashing when the screen comes on. Anyway, a defective power board is one of the major reasons for this blink.
Sometimes, clogged ventilation and defective or loose cable connections lead to the same system error. Like other blinking codes, this issue can also be resolved by following some straightforward methods:
Solutions:
First, make sure you have unplugged your TV.
Now, check out the ventilation system of your TV. Clean out all the vents to ensure air circulation fluently.
Also, ensure a stable installation of the TV.
Disconnect all the cables and reconnect them firmly and in proper working order.
Remove all connected devices.
Don’t miss the TV ports and all should be properly cleaned.
While unplugging, press the power button for about 20 seconds.
Leave the TV unplugged for about 1 hour. This will do a power reset on your TV.

SOURCE: electrofixs.com

Related Error Code Pages:
Hisense Television Error Codes, Hisense Refrigerator Error Codes, Hisense Range Error Codes, Hisense Dishwasher Error Codes,

Related Troubleshooting Pages:
Hisense Television Troubleshooting, Hisense Refrigerator Troubleshooting, Hisense Range Troubleshooting, Hisense Dishwasher Troubleshooting,

Related Repair Pages:
Hisense Television Repairs, Hisense Refrigerator Repairs, Hisense Range Repairs, Hisense Dishwasher Repairs,

Related Parts Pages:
Hisense Television Parts, Hisense Refrigerator Parts, Hisense Range Parts, Hisense Dishwasher Parts,

Related Price Pages:
Hisense Television Prices, Hisense Refrigerator Prices, Hisense Range Prices, Hisense Dishwasher Prices,

Related Pages: