Appliance Types


Appliance Brands


Article Categories


More Articles


KitchenAid Appliances
KitchenAid Appliances

KitchenAid Appliance Error Codes

KitchenAid and millions of fellow Makers are here with challenges, ideas, inspiration, and motivation.


Dishwasher Error Codes

CODE: 1-1 or F1E1 
PROBLEM: Stuck relay on the electronic control board 
FIX: Shut off power to the dishwasher for 5 minutes. If the code resumes when you restore power, check the wiring connected to the control board for damage and repair any broken wires. Measure the resistance through all components connected to the control board using the tech sheet as a guide. You can find the tech sheet behind the bottom front toe panel of the dishwasher. 

CODE: 1-2 or F1E2 
PROBLEM: Damaged or corrupted memory on control board. Incompatible software components inside microprocessor., 
FIX: Shut off power to the dishwasher for 5 minutes. If the code resumes when you restore power, replace the electronic control board. 

CODE: 2-1 or F2E1 
PROBLEM: Stuck button on the user interface control 
FIX: Check all buttons on the user interface control for a response. If one or more of the buttons don't work, unplug the dishwasher to disconnect electrical power and disconnect the user interface control wire harness. Reassemble the door with the user interface wire harness disconnected, but don't close the door. Plug in the dishwasher and wait at least 7 seconds for the electronic control board to power up completely. Then close the door. 

CODE: 2-2 or F2E2 
PROBLEM: User interface control can't communicate with electronic control board 
FIX: Shut off power to the dishwasher. Check the wiring between the user interface control and the electronic control board. If the wires and connections are okay, replace the user interface control board. If the problem persists, replace the electronic control board. 

CODE: 3-1 or F3E1 
PROBLEM: Thermistor/OWI sensor failure (The thermistor is the water temperature sensor, the OWI sensor is the Optical Water Indicator that detects the amount of debris in the water.) 
FIX: Unplug the dishwasher to disconnect electrical power and then check the wiring between the electronic control board and the thermistor/OWI sensor. Repair or replace the wire harness if broken. If you find the wiring undamaged, replace the thermistor/OWI sensor. 

CODE: 3-2 or F3E2 
PROBLEM: Shorted thermistor/OWI sensor 
FIX: Unplug the dishwasher to disconnect electrical power and then check the wiring between the electronic control board and the thermistor/OWI sensor. Repair or replace the wire harness if broken. If you find the wiring undamaged, replace the thermistor/OWI sensor. 

CODE: 3-3 or F3E3 
PROBLEM: OWI failed to calibrate or the drain hose check valve failed, allowing dirty water to backflow into the dishwasher 
FIX: Disconnect the dishwasher drain hose connection from the air gap or the garbage disposal if you have no air gap. Pour water through the drain hose to see if water backs up into the dishwasher tub. If so, replace the portion of the drain hose that connects to the drain pump because the check valve in that hose failed. If water doesn't back up into the dishwasher through the drain hose, reconnect the hose and run the Service Diagnostics Test according to the instructions in the tech sheet. 

CODE: 4-4 or F4E4 
PROBLEM: Communication error between the electronic control board and the circulation pump motor 
FIX: Unplug the dishwasher to disconnect electrical power. Check the circulation pump wire harness and reconnect any loose wires or replace the wire harness if damaged. If the wiring connections are okay, replace the circulation pump and motor assembly. If the problem continues, replace the electronic control board. 

CODE: 5-1 or F5E1 
PROBLEM: Door switch failure 
FIX: This code appears if you don't close the door within 4 seconds of pressing the Start/Resume button, or if the door latch assembly is broken. When starting a cycle, close the door within 4 seconds after pressing Start/Resume. If you can't start the cycle and the code continues, then the door switch could be defective. Unplug the dishwasher to disconnect electrical power. 

CODE: 5-2 or F5E2 
PROBLEM: Control detects door not opening 
FIX: The electronic control board expects to see the door open between cycles or the dishwasher won't start the next time you try to start a new cycle. If you didn't open the door between cycles, cancel the cycle. Open and shut the door, and then start a new cycle. If the cycle still won't start, then the door switch could be defective. Unplug the dishwasher, then plug it back in to simulate the door opening. If the cycle starts, replace the door latch assembly because the door switch isn't detecting the door opening. 

CODE: 6-1 or F6E1 
PROBLEM: Won't fill 
FIX: Check for an item stuck under the overfill float and remove it. If the overfill float sticks in the "up" position the dishwasher won't fill. Unplug the dishwasher to disconnect electrical power and shut the water supply valve. Disconnect the water supply line from the water inlet valve and check the water inlet valve screen for clogs. Replace the water valve if you find the screen clogged because debris from the clog can get into the valve body, causing the valve to stick open and possibly flood your kitchen. 

CODE: 6-2 or F6E2 
PROBLEM: Water inlet valve failure 
FIX: Unplug the dishwasher to disconnect electrical power. Remove the bottom front access panel and toe panel. Check the wire harness connections on the water inlet valve. Reconnect any loose wires. Replace the wire harness if damaged. If the wire harness connections are okay, check the resistance of the water inlet valve using a multimeter. 

CODE: 6-3 or F6E3 
PROBLEM: Suds or air are in the water pump 
FIX: Check for sudsy water. If you see excessive suds, try to drain the dishwasher by cancelling the cycle. The drain pump will run for 3 minutes. If the drain pump can't drain the sudsy water, drain the water by hand or use a wet/dry shop vacuum to remove the water. Check the detergent dispenser and replace if it's damaged. Use only dishwasher detergent in the dishwasher. Using regular dish soap in the dishwasher causes excessive suds. If you don't see excessive suds, check the water fill level in the tub because low water level causes air in the pump. 

CODE: 6-4 or F6E4 
PROBLEM: The float switch is open 
FIX: Check the overfill float switch to see if it's stuck or if an item is stuck under it. Check if the inlet water fill valve is properly shutting off the water supply when the dishwasher is off. 

CODE: 6-6 or F6E6 
PROBLEM: Incoming water is too cold 
FIX: Use an accurate thermometer to check the water temperature. If it's lower than 110 degrees F, check your water heater. water heater. If the water temperature is normal (110 to 120 degrees F), replace the thermistor/OWI or the electronic control board. Refer to the tech sheet for your dishwasher for a diagnostic test for the thermistor. 

CODE: 7-1 or F7E1 
PROBLEM: Heating element doesn't work 
FIX: Shut off power to the dishwasher. Inspect the heating element and replace it if it's visibly damaged. If not, check the wiring to the heating element. If the wiring is intact, replace the heating element. 

CODE: 7-2 or F7E2 
PROBLEM: Heating element won't shut off 
FIX: Shut off power to the dishwasher for 5 minutes. If the code resumes when you restore power, replace the electronic control board. 

CODE: 8-1 or F8E1 
PROBLEM: Slow drain 
FIX: Shut off power to the dishwasher and then shut off water. Check the drain path for an obstruction. If the drain path is clear, check the wiring on the drain pump. If the wiring is intact, replace the drain pump. 

CODE: 8-2 or F8E2 
PROBLEM: Drain pump electrical problem 
FIX: Shut off power to the dishwasher and then shut off water. Check the wiring on the drain pump. If the wiring is intact, replace the drain pump. 

CODE: 9-1 or F9E1 
PROBLEM: Electronic control board can't detect the position of the diverter disc 
FIX: The diverter motor positions the disc that directs the water through the lower spray arm or the upper spray arm. The diverter motor also monitors the position of the diverter disc and sends position signals to the electronic control board. Unplug the dishwasher to disconnect power and check the wiring going to the diverter motor. Reconnect any loose wires or replace the wire harness if damaged. 

CODE: 9-2 or F9E2 
PROBLEM: Diverter motor is stuck on 
FIX: The diverter relay on the electronic control board is defective. Unplug the dishwasher to disconnect electrical power and replace the electronic control board. 

CODE: 9-3 or F9E3 
PROBLEM: Diverter disc is missing 
FIX: Remove the dishracks and the lower spray arm. Pull out the TurboZone manifold and the feed tube. Remove the pump outlet and check the diverter disc. Replace the disc if it's broken or missing. 

CODE: 9-4 or F9E4 
PROBLEM: Lower spray arm error 
FIX: Check for obstructions blocking the lower spray arm from turning. Shut off power to the dishwasher and check the wiring connections on the lower spray arm motor. If the wiring is intact, replace the lower spray arm motor. 

CODE: 10-1 or FAE1 
PROBLEM: Detergent dispenser failure 
FIX: Unplug the dishwasher to disconnect electrical power. Remove the outer door panel and check the wiring connections between the electronic control board and the detergent dispenser. Reconnect any loose wires or replace the wire harness if damaged. If the wiring is intact, replace the detergent dispenser. 

CODE: 10-2 or FAE2 
PROBLEM: Vent wax motor electrical problem 
FIX: Shut off power to the dishwasher. Check the wiring in the vent wax motor circuit. If the wiring is intact, replace the vent wax motor. 

CODE: 10-3 or FAE3 
PROBLEM: Drying fan failure 
FIX: Unplug the dishwasher to disconnect electrical power. Check the wiring between the electronic control board and the drying fan. Reconnect any loose wires or replace the wire harness if damaged. If the wiring is intact, replace the drying fan. 
 


Microwave Error Codes

CODE: F1-E3 / F1-E4 
PROBLEM: Control Board Failure - Replace control board (clock). 
 
CODE: F2-E0 / F2-E1 
PROBLEM: Touch Pad (Keypad) Not Connected - Check connection between touch pad and control board (clock). 
 
CODE: F2-E3 
PROBLEM: Touch Pad (Keypad) Shorted or Key Held Down Too Long - Select 'cancel' and observe for 60 seconds. If error reappears, replace touch pad, or touch and pad and control board (clock) if all one assembly.


Range Error Codes

CODE: F1-E0  
PROBLEM: EEPROM Communication Error  
FIX: Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). 

CODE:F1-E1  
PROBLEM: EEPROM Checksum Error  
FIX: Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). 

CODE:F1-E2  
PROBLEM: UL A/D Error(s)  
FIX: Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). 

CODE:F1-E4  
PROBLEM: Model Id Error  
FIX: Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). 

CODE:F1-E5  
PROBLEM: Calibration Shifted  
FIX: Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). 

CODE:F1-E6  
PROBLEM: Latch Signal Mismatch Error  
FIX: Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). 

CODE:F1-E9  
PROBLEM: Stack Overflow  
FIX: Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). 

CODE:F1-E3  
PROBLEM: Wiring Harness Cavity Size Does Not Match Stored Value  
FIX: Check the jumpers in the harness to make sure they agree with the actual oven size. 

CODE:F2-E0  
PROBLEM: Shorted Touch Pad (Keypad)  
FIX: Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. 

CODE:F2-E1  
PROBLEM: Touch Pad Cable Unplugged  
FIX: Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. 

CODE:F2-E5  
PROBLEM: Cancel Key Line Open  
FIX: Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. 

CODE:F2-E6  
PROBLEM: Cancel Key Line Open  
FIX: Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. All F3-E Codes - Oven Temperature Sensor (RTD) or Warming Drawer Defect - Replace oven temperature sensor (RTD). 

CODE:F4-E1  
PROBLEM: Meat Probe Defect  
FIX: This error indicates a problem with either the probe, receptacle, or probe circuit. Check the probe for pinched wires and make sure there is no condensation or contamination on receptacle. If ok, replace probe. 

CODE:All F5-E Codes  
PROBLEM: Door Switch Defect  
FIX: This occurs when the door switches do not match. If door is latched, disconnect power from unit and check wires and connections. If damage is found, replace appropriate part. If connections are not damaged, reconnect power and hold down any key until the F5 error clears. Once the F2 code appears, select 'cancel' and observe for one minute for errors. If door is NOT latched, disconnect power from unit and check wires and connections. If damage is found, replace appropriate part. If connections are not damaged, measure door switch (door open = latch open) and latch switch (unlatch = switch open) and replace either if defective. If corrections are made during any step, power should be reconnected and the unit should be tested. Press and hold any key to clear the error code and F2 code should appear. Select 'cancel' and observe for one minute for errors. If error continues, disconnect power and replace control. 

CODE:F6-E0  
PROBLEM: Return Line Not Connected  
FIX: This error should appear within 60 seconds after power up to appliance. Replace control board (clock). 

CODE:F7-E1  
PROBLEM: Common Switch Wire Is Defective  
FIX: This error occurs when common wire to latch switch and door switch is shorted. Check all connections at control board and at the latch switch and door switch. If connections are ok, then check individual switches as outlined for the F5 error code. Note: Double ovens will have two of each switch and one common wire.


Refrigerator Error Codes

CODE: 1E 
PROBLEM: FZ Sensor Error 
FIX: The sensor is read as open or shorted. Check the wiring connections. 
 
CODE: 2E 
PROBLEM: R Sensor Error. 
FIX: The sensor is read as open or shorted. Check the wiring connections. 
 
CODE: 4E 
PROBLEM: FZ DEF Sensor Error. 
FIX: The sensor is read as open or shorted. Check the wiring connections. 
 
CODE: 5E 
PROBLEM: R DEF Sensor Error. 
FIX: The sensor is read as open or shorted. Check the wiring connections. 
  
CODE: 6E 
PROBLEM: Ambient Sensor Error. 
FIX: The sensor is read as open or shorted. Check the wiring connections. 
 
CODE: 7E 
PROBLEM: Flex Sensor Error. 
FIX: The sensor is read as open or shorted. Check the wiring connections. 
  
CODE: 13E 
PROBLEM: Humidity Sensor Error. 
FIX: The Humidity sensor is read as open or shorted. Check the wiring connections. 
 
CODE: 14E 
PROBLEM: IM Sensor Error. 
FIX: The sensor is read as open or shorted. Check the wiring connections. 
 
CODE: 15E 
PROBLEM: ICE RM Sensor Error. 
FIX: The sensor is read as open or shorted. Check the wiring connections. 
 
CODE: 21E 
PROBLEM: FZ Fan Error. 
FIX: The freezer fan motor is read as not connected or the fan has stopped. Check the wiring connections. 
 
CODE: 22E 
PROBLEM: R Fan Error. 
FIX: The Ref fan motor is read as not connected or the fan has stopped. Check the wiring connections. 
 
CODE: 23E 
PROBLEM: C Fan Error. 
FIX: The Comp. fan motor is read as not connected or the fan has stopped. Check the wiring connections. 
  
CODE: 24E 
PROBLEM: FZ Def Function Error. 
FIX: The freezer defrost heater is read as open or the heater has been heating continuously for more then 80 mins. 
 
CODE: 25E 
PROBLEM: R Def Function Error. 
FIX: The refrigerator defrost heater is read as open or the heater has been heating continuously for more then 80 mins. 
 
CODE: 39E 
PROBLEM: IM Function Error. 
FIX: The ice maker release heater reads as open circuit.



KitchenAid Appliance Error Codes

KitchenAid appliance fault codes

KitchenAid appliance diagnostic codes

KitchenAid appliance error symbols

KitchenAid appliance common faults


Product Reviews:

I am very disappointed in the Aqua clean feature on my KitchenAid range. It
I am very disappointed in the Aqua clean feature on my KitchenAid range. It simply does not remove the grease. I should have followed my instinct and not purchased it. I agree the smooth glass top scratches easily also, but I decided not to worry about that. On a positive note, the oven and burners cook nicely.
Published: January 13, 2019
Dana of Ridgecrest, CA
Source: consumeraffairs.com

I am grateful for the microwave I have. When you do not have a lot of money
I am grateful for the microwave I have. When you do not have a lot of money you tend to use things as long as possible. I have had this microwave for 8yrs, given to me used and it still works great (never burn my popcorn).
Published: January 18, 2017
Penny of Syracuse, New York
Source: consumeraffairs.com

We remodeled our house and purchased a KitchenAid microwave oven wall unit
We remodeled our house and purchased a KitchenAid microwave oven wall unit Model number KEMS308SSS05. We have owned this unit 2 years and 2 months. The microwave always had a loud sound when running and did not heat. Well we had the microwave serviced within months of purchase while under the manufacturers warranty, it started heating better. Recently the turntable stopped working. We had 5 service calls before it was fixed. The motor had to be replaced along with several electronic boards. Now the oven will not heat to set temp and does not hold its heat. The repair company is coming to fix next week. I will never buy a KitchenAid appliance again. This was my 1st experience with KitchenAid. We also have a high end Kitchen dishwasher which we had to replace plastic parts for the upper drawer. Very Poor Quality. Now I know why KitchenAid does not have a customer service line you can call.
Published: July 25, 2014
Gail of Omaha, NE
Source: consumeraffairs.com

We remodeled our kitchen in 2004, bought top of the line appliances. I have
We remodeled our kitchen in 2004, bought top of the line appliances. I have had nothing but bills with all of them, the dishwasher being the worst. We bought the appliances at Lowes with the 3-year warranty. Used the warranty and still am being out money for repair. So disappointed in what my husband and I thought was the best.
Published: June 21, 2013
Ramona of Boonville, IN
Source: consumeraffairs.com

We recently bought a used KitchenAid stainless steel stove. The control kno
We recently bought a used KitchenAid stainless steel stove. The control knobs are at the front of the oven and we discovered that they are easily turned on with even the slightest touch or bump. Unfortunately, when working in the kitchen, I did not notice that I had lightly touched the control knob which turned on the High setting. Within minutes the high setting ignited the oil in the pan on a front burner and flames were shooting up hitting the over-the-stove microwave oven. The flames covered the bottom edge of the microwave and the plastic edge melted.Luckily I was able to extinguish the fire, but my house has extensive smoke damage and could have completely gone up in flames. As well, the microwave oven is no longer useable. The stove knobs are a serious safety hazard as they can too easily be turned on with a light touch, a childs hand or even a dog sniffing the front of the stove. We are going to throw the stove out and never buy a KitchenAid appliance again.
Published: November 23, 2016
Patricia of North Vancouver, BC
Source: consumeraffairs.com

The control panel of my double wall ovens periodically puts out error codes
The control panel of my double wall ovens periodically puts out error codes and the only way to turn off the oven is by turning off the circuit breakers. Six months later, still no service. Multiple calls and run around by KitchenAid and the Extended Warranty company.
Published: July 21, 2014
Miriam of Toronto, ON
Source: consumeraffairs.com

I purchased microwave/hood combo in October 2010, installed November 2010.
I purchased microwave/hood combo in October 2010, installed November 2010. Unit no longer heats as of mid December 2011. I did not want microwave in the way for holidays so I contacted them in January. The second service call, I was informed element inside turntable had melted. After several more service calls, six all together, my unit has been on my dining room table for almost three months. Repeated calls to Whirlpool/KitchenAid have gotten me nowhere. I maintained that if part of the turntable melted, unit must be defective. I now have to pay $315 to get the unit replaced. They have no concern that I missed work on numerous occasions for failed service calls or that I paid for initial service call. If product is defective, it should be replaced without further cost to me.
Published: March 6, 2012
Patricia of Eastchester, NY
Source: consumeraffairs.com

Our 3 year old, $3100.00 refrigerator is leaking water from the bottom. Whe
Our 3 year old, $3100.00 refrigerator is leaking water from the bottom. When checking it further, I found a layer of ice that had formed under the freezer drawer. I removed it once last week and rearranged the frozen food to ensure adequate circulation of air around the entire freezer drawer. Well, this morning, once again, the water is on the floor and ice under the drawer. WHAT COULD BE CAUSING THIS PROBLEM? All kitchen appliances are KitchenAid and this is the only one with problems, so far.
Published: August 4, 2015
P. of Greeley, CO
Source: consumeraffairs.com

This is quick, easy, and short. I purchased a new KitchenAid side by side
This is quick, easy, and short. I purchased a new KitchenAid side by side in March of 2011. One month later, it stopped cooling. As a service tech, I had already tested and found that the start relay and overload were bad because the compressor was about to take a dump. I called for service which took about a week to arrange. When the service tech arrived, he replaced the relay and overload without testing the compressor. I asked him if that was common practice which I knew wasnt. He replied that it was a common problem and it wasnt necessary to test the compressor and everything should be fine. Little did he know about my abilities. Knowing KitchenAids reputation, I was fully prepared on how to deal with the situation and didnt want or need to have to go through what so many others had to do. Also knowing that the compressor only had a limited life of maybe a week before it quit completely, I first purchased a used old refrigerator for $50.00 to get me by just in case. In about 8 days, the problem with the original fridge returned now even worse. Then, I went to the same store I bought the original KitchenAid. I purchased the same unit on my credit card for over $2,600. Foreseeing what was impending doom for the original fridge, I moved it out of site and had the new one delivered. The next day, I canceled the credit card transaction for the new fridge and called the store to advise them to come and get the fridge. What they didnt know is I exchanged the old fridge with the new one and even switched the ID tags that have the serial number. The next day, the store came to get the fridge not knowing they got the old one broken back in exchange. Ironically, no one had a clue nor did they even check. So, I ended up with a working new refrigerator. And I didnt have to deal with poor service not only from the store, KitchenAid reps, or a service provider that doesnt have a clue on how to repair these products. In the end, I not only now have a good working and new refrigerator, but the old one I bought as a stand by for $50 was cleaned up and completely checked out, then sold for $150.00.
Published: October 21, 2011
Patrick of Buffalo, NY
Source: consumeraffairs.com

This refrigerator fit perfectly into our built-in space, and is great looki
This refrigerator fit perfectly into our built-in space, and is great looking and has all the latest features. The interior space of our side by side style fridge however, is a little cramped. Weve had excellent service and support on this brand.
Published: September 12, 2019
Alfred & Linda of Frisco, TX
Source: consumeraffairs.com

My Husband and I bought this stove 2 years ago for our rental unit, we neve
My Husband and I bought this stove 2 years ago for our rental unit, we never had any complaints from our tenants. But in January we moved in to the property and since then my mind has not been at peace. I have for little girls and we have had episodes were they pass by the stove and happen to bump into the stove and it will turn on the gas. I myself have leaned over the stove to get something and it will turn on, the sad part is we wont notice until we smell the gas. I tried buying some knob covers online but they did not fit due to an extra ring on each knob. So I called KitchenAid and explained the situation. I was expecting a solution, instead they sent some service guys who were very honest and said they couldnt do anything about it and that the company probably had no solution for this either. They recommended searching online for a piece that could cover all the knobs! Really? So if my house happens to blow up in the middle of the night its okay, or if my 3 year old turns on the stove and gets burnt then what? They need to recall these stoves or fix the knobs to be safer and harder to turn on.
Published: May 7, 2020
Robely of Salem, NH
Source: consumeraffairs.com

We purchased a Kitchen Aid gas stove-top in August 2010, for $1,323. Today,
We purchased a Kitchen Aid gas stove-top in August 2010, for $1,323. Today, I noticed that the knob for the fan was cracked in two places, because it is made out of cheap junk plastic. We barely ever used that fan. We bought a Kitchen Aid stove, based on their reputation, which apparently they no longer deserve. I asked them to replace the obviously defective piece, but they just copied and pasted a bunch of warranty paragraphs. So instead of replacing the knob for me, they would rather have me write reviews of their product. So here it is!
Published: January 16, 2012
Joanne of Barrington, NH
Source: consumeraffairs.com

The dishwasher has been repaired two times and is leaking again. I hate thi
The dishwasher has been repaired two times and is leaking again. I hate this dishwasher and almost from day one. I only had it a short time and it started to leak all over my wood floors. We had it fixed and again. We had to pay to repair the leak a second time and again water on my wood floors. Today, I came upstairs to find water all over the floors again! Plus, it hasnt really cleaned the dishes well in a long time. I am going out today and shop for a new dishwasher and will not even consider KitchenAid. And I had a KitchenAid stove for a very short time and had to go out and buy a GE because at Thanksgiving, the oven stopped working. Right now, I have a KA refrigerator and cannot wait to get rid of it. I will never buy anything KitchenAid. Ill try Bosch or stick with GE!
Published: July 1, 2012
Diana of Boalsburg, PA
Source: consumeraffairs.com

I purchased $12,000 in appliances a year ago during a remodel of my existin
I purchased $12,000 in appliances a year ago during a remodel of my existing kitchen. Since day one, the commercial gas stove has been a problem. I had more than five repairs and every time, it would start something new to go wrong. One afternoon, I thought I smelled smoke and when I turned around, the entire electronic portion of the stove was on fire. After extinguishing the fire, I called the distributor and was told Whirlpool will replace the stove immediately and we will cover the expense of the installation. That was seven weeks ago, no stove, so phone call from Whirlpool, no reciprocation for my patience. Yesterday, I was told that it is probably back-ordered. ** Whirlpool, my house could have burned down if I had not been there and yet seven weeks later, I am still waiting? Never again will I buy another Whirlpool product and especially KitchenAid. Im still without a stove in a $50K remodeling job. I have called an attorney so dont bother with a phone call.
Published: May 10, 2012
William of Fairborn, OH
Source: consumeraffairs.com

Bought a KitchenAid Dishwasher 15 months ago. Almost $900. Wife wanted it t
Bought a KitchenAid Dishwasher 15 months ago. Almost $900. Wife wanted it to match our KA fridge. I thought, for that kind of $$, the KA DW would clean better and last longer than my moms $300 Kenmore. But the KA has never cleaned well, even with top-line Cascade products. This week, it would start but not complete a cycle. Nothing in the manual about this. Called customer service. Took them 20 minutes to tell me they have no troubleshooting advice for this problem. My only option was to pay for a service call and the machine is just 3 months out of warranty! I told the lady that I would be writing many uncomplimentary reviews. Im convinced that KitchenAid is not worth the extra money. It is NOT a better product.
Published: October 12, 2013
David of Cupertino, CA
Source: consumeraffairs.com

3 years ago, performance KitchenAid dishwasher. This dishwasher has been a
3 years ago, performance KitchenAid dishwasher. This dishwasher has been a piece of crap since day one. Within one week of running the dishwasher at the motherboard had to be replaced. The plastic clips how did replace six times and still continue to break. The spraying arms on the top and bottom continually failed to work. We paid $1200--it is dishwasher that doesnt work. Will never buy a KitchenAid appliance again.
Published: March 12, 2015
Debbie of Colorado Springs,, CO
Source: consumeraffairs.com

I just got off the phone and as usual got nowhere with KitchenAid people in
I just got off the phone and as usual got nowhere with KitchenAid people including the manager. I too have had nothing but headaches with this piece of junk. As someone said, the top rack just collapsed downward on one side. We replaced the rack, and another part already; the junky plastic on the rack keeps breaking. The door for the soap doesnt open and it has been a better dish rack than dishwasher. I have washed dishes by hand more often than I was able to use this product. I am so disappointed that they, as a big company, couldnt send someone out for free for a change and try to back their name. They brag as you wait on the phone (which is forever), about how wonderful their service is. Well, the last visit cost over $100 to have a man run my dishwasher empty and tell me to use less soap and not packets. Now a manager told me to see if it works in the other types of washes. I asked how that would solve my problem. What am I supposed to do, switch from my one hour and compromise? I told him management is not his calling and he should consider another job. Never again will I buy KitchenAid which is a shame because my first one was great!
Published: July 8, 2013
Donna of Bethlehem, PA
Source: consumeraffairs.com

We purchased a stainless freezer at the bottom model in January of 2013 fro
We purchased a stainless freezer at the bottom model in January of 2013 from a local appliance store. Within a couple of months we had a freezer that stopped getting cold and lost all the food in it. A repairman came quickly and said it was working fine and it continued for a year. Then the freezer stopped working for a day, but came back on. In October of 2015 the freezer stopped completely. We have had a series of repairmen out and we still have no freezer. I have called KitchenAid and they said they would only fix and repair what is in the sealed unit, but that often the control panels fail and that they wont fix or replace the control panel. We paid top dollar for a fridge that lasted two years. There is no way I would ever buy a KitchenAid product again for any reason. This has been a nightmare. We were without a fridge during the hottest two months on record and now we are going into the holidays without a fridge/freezer. I would never recommend buying a KitchenAid appliance and would warn anyone to avoid this company.
Published: November 11, 2015
Kara of Oxnard, CA
Source: consumeraffairs.com

Same as thousands who have bought Kitchen Aid ovens, I bought a complete Ki
Same as thousands who have bought Kitchen Aid ovens, I bought a complete KitchenAid kitchen. I have the convection oven and convection microwave built in. Whenever we use the clean on the oven, it burns out the thermal fuse and KitchenAid gives no help. The model is KKUDS40FVSS and costs about $2000 of self-cleaning that doesnt clean. When they reply, they cover parts but not labor.
Published: January 1, 2012
Rick of Kindred, ND
Source: consumeraffairs.com

We purchased a KitchenAid refrigerator made by Whirlpool 3 yrs ago when we
We purchased a KitchenAid refrigerator made by Whirlpool 3 yrs ago when we remodeled our kitchen. Before it was even 2 yrs old we started having problems. In the last year we have had to have it repaired 4 times. Even the tech guy said they are a problem. I just wonder how you can sell a product that you know is a piece of crap. Buyer beware. Dont buy a Whirlpool product. I just wonder how many time do we have to go thru this before they make it right?
Published: May 17, 2018
Donna of San Diego, CA
Source: consumeraffairs.com

Our KitchenAid dishwasher broke down after eight months. They replaced the
Our KitchenAid dishwasher broke down after eight months. They replaced the water pump, which took three weeks. Two months later it broke down again. They replace a circuit board and water pump again, but still did not work. They again replaced the third water pump with no luck. The technician thinks it may be a wiring harness so now we are still without a dishwasher and are waiting for that part. By now I am asking for a new dishwasher from KitchenAid but they insist that my warranty only covers parts replacement and will continue to replace parts until they deem it necessary to replace. Dealing with customer service has been a very unpleasant experience. I have vowed that I will never buy another KitchenAid or Whirlpool or Frigidaire appliances again. We are now looking at replacing the dishwasher at our own cost.
Published: January 30, 2019
Daniel of Other
Source: consumeraffairs.com

Issue 1: Condensation inside the back wall of refrigerator and thus make th
Issue 1: Condensation inside the back wall of refrigerator and thus make the refrigerator more noisy. Noise level is higher than the normal, because the ice is surrounded by refrigerator fan, so when the fan runs it is louder. Issue 2 . Not making the ice. In spite of 6 visits by the technicians, the issues is not resolved so far.
Published: January 13, 2014
Obula of Portland, OR
Source: consumeraffairs.com

I purchased a complete house full of Kitchen Aid products about 8 years ago
I purchased a complete house full of Kitchen Aid products about 8 years ago, paying a little extra for a Brand I thought at the time was top of the line in terms of features and quality. Boy was I wrong, the following is a list of costly issues Ive encountered over what I think is an unacceptable product life span...some of the breakdowns occurred just outside of warranty, some continue: - Fridge Fan assembly replaced (overheating) - Fridge cheap plastics, many shelves easily damaged - Stove burner replacement, electric front panel malfunctioning - Dishwasher Circulation Motor seized - Dishwasher door closing mechanism malfunction - Clothes Washer control board failure- Clothes Dryer faulty ignitor (gas appliance)This is the list so far but Im expecting further issues down the road, I paid thousands of dollars for these appliances and expected them to last much longer...next time I will do my homework, that said...Im done with Whirlpool/KitchenAid.
Published: May 17, 2014
D of Embrun, ON
Source: consumeraffairs.com

Bought the Kitchen Aid Dishwasher Model KUD301XSS9 in July 2013. 13 months
Bought the Kitchen Aid Dishwasher Model KUD301XSS9 in July 2013. 13 months later, like many of these other reviews, had to replace the plastic tabs on the top rack on both sides. Of course, they were on back order (apparently a lot of replacements of those parts on the top rack). I went ahead and ordered two sets for each side, anticipating this will happen in another 12 months or so. The plastic does not appear to be able to stand up to the high temperatures generated by this dishwasher. Had I known that Kitchen Aid was owned by Whirlpool, who also owns Maytag, which, in my opinion, is absolutely the WORST appliance manufacturer since the beginning of time, I would not have bought one. The old slogan from the 1980s about the Maytag Repairman being lonely would not be applicable today... Apparently neither would the Kitchen Aid Dishwasher repairman. Heading over to GE the next time, at least They Bring Good Things to Life, and one of those Good Things will be in the form of a better dishwasher to my home. Now this model is not all bad. The good thing about this model is the same thing that probably cause the problem to begin with... it does dry very good. What KA needs to understand is no consumer wants to be replacing ANY part after only 13 months of service. From reading the reviews, I am not totally convinced they are able to grasp that concept.
Published: January 25, 2015
Robert of Plano, TX
Source: consumeraffairs.com

The valve that allows water to shut off in the dishwasher freezes open caus
The valve that allows water to shut off in the dishwasher freezes open causing the water to flow out of the front of door and flood your floor. The first time I was standing there and thought the door may not have closed. About 4 months later I was not there and it flood the kitchen, into the hall and living room. Called Sears. They sent a repair guy. He saw the water did not turn off even when you opened the door of the dishwasher, he said these valves have a problem and sometimes it is intermittent. Sears tested the valve and of course it worked, so they said the water damage was not from that. So lesson learned take a video. So where else did the water come from? Spent $800 for a turn off valve for dishwasher under sink and plumber said no leaks. Need this valve because I do not trust this dishwasher, will be looking at Bosch.
Published: April 14, 2017
Elizabeth of Escalon, CA
Source: consumeraffairs.com

I purchased a Kitchen Aid refrigerator (Model # KRMF706ESS01) that hasnt ev
I purchased a Kitchen Aid refrigerator (Model # KRMF706ESS01) that hasnt ever cooled in the refrigerator or freezer. KitchenAid sent a service tech who found no freon. Now KitchenAid refuses to do anything until they send a second company. They said the first company was not qualified to fix the problem even though they chose to send them. Now we are without a refrigerator for weeks. This is a brand new refrigerator that has never been used. KitchenAid has very poor quality service and products.
Published: July 29, 2016
Tanya of Christiansburg, VA
Source: consumeraffairs.com

The refrigerator works and does what it supposed to do, but the noise level
The refrigerator works and does what it supposed to do, but the noise level is intolerable. Their service said that there is nothing that can be done. It is noisy: 24/7.
Published: December 2, 2017
Fred of West Bloomfield, Michigan
Source: consumeraffairs.com

We purchased KitchenAid fridge, Model # KFIS29PBMS00 from Lowes in May of 2
We purchased KitchenAid fridge, Model # KFIS29PBMS00 from Lowes in May of 2015. We began having problems within 2 weeks of it being installed in our home. We had to have it serviced 7 times to finally get it repaired. It was finally repaired by the end of June. Subsequently, I had to keep throwing away food, taking off of work, etc. Now, 9 months later, it is working infrequently now. It started making a noise, like a lower sound like a leaf blower. Then, it started losing temperature. Main purpose of my writing a review... dont be fooled by KitchenAid supposedly being one of the top the line fridges/freezers at Lowes. At our old home, the fridge was there when we moved in and was still working perfectly when we left 10 1/2 years later. It was a GE.Result: I will never buy another Kitchen Aid or Whirlpool product. Although some of their products may be acceptable, the company has cost my family money through the loss of food and work and inconvenience for 9 months for a fridge that cost almost $2000! They should replace it because apparently it is a sub-standard product.
Published: February 4, 2016
Michelle of Lexington, SC
Source: consumeraffairs.com

Updated on 10/04/2020: When the compressor failed the digital read out disp
Updated on 10/04/2020: When the compressor failed the digital read out display also went. The compressor is covered by 5 year warranty, but not the digital display panel. They failed on the same day?? This is a top of their line unit. (Not cheap). They came out and gave me an estimate of $600 for new digital readout unit. I am at 6 weeks and counting without the fridge and no one can give me a date!Original Review: Appliance was 4 months off first year warranty when compressor failed causing electric control panel to need replacing. Although compressor is covered in second year I was charged for the service call and new control panel (over $600). This was a $2400 bar fridge. I expected better quality and service after purchasing $20,000 in KitchenAid appliances. Not sure this will ever be my brand in the future.
Published: August 31, 2020
Raymond of Victoria, BC
Source: consumeraffairs.com

To KitchenAid Dishwashers: Compliments and thanks! KitchenAid has stepped u
To KitchenAid Dishwashers: Compliments and thanks! KitchenAid has stepped up big time, so I want to update my November 7 negative review of dishwasher model # KDFE204EWH. This morning, we got a very nice phone call from KitchenAid’s customer care people. They will pay for the part replacement and the installation labor. In a happy coincidence, their local authorized service operation happens to be the same (first-rate) dealer we bought the dishwasher from, so I know the follow-through will be there. Two takeaways: At least one of the “squawking platforms” that we used for our complaining this past week did the trick, so complain widely! And It likely also helped that we promptly registered our purchase with KitchenAid, so they already had all the details.
Published: November 10, 2018
V. of Little Rock, AR
Source: consumeraffairs.com

As a retired chef I have preference for gas cooktop but electric oven. I bu
As a retired chef I have preference for gas cooktop but electric oven. I built a new home with floorplan that did not offer separate cooktop and wall oven so I was very pleased when I found a Kitchenaid dual fuel product offering gas cooktop and electric oven combination. I had past experience with KitchenAid and thought I was purchasing a quality product.Although the cooktop and oven function well, the so-called AquaLift self-cleaning feature is useless! I do not let my oven become heavily soiled but found my first use of this feature did nothing to clean the oven. Even worse, instructions indicate even if I was willing to use an oven cleaning product and elbow grease I am warned this will damage the oven surface. It appears there are currently class action suits on this topic. Wish I had known this before purchasing this expensive product.
Published: December 29, 2019
M. of Mesa, AZ
Source: consumeraffairs.com

Too many details to go over all. Fridge broke under warranty. Repair guy co
Too many details to go over all. Fridge broke under warranty. Repair guy couldnt fix. Replacement fridge left off truck for delivery. 2.5 months after initial call, still waiting for repaired or replaced $3199 refrigerator. DO NOT BUT KITCHENAID PRODUCTS.
Published: July 19, 2019
Patrick of West Bend, WI
Source: consumeraffairs.com

I have had this dishwasher for less than 2 years and have had the upper tra
I have had this dishwasher for less than 2 years and have had the upper track rack adjusters replace 3 or 4 times. Now they are broken again and the unit is out of warranty. I cant believe a dishwasher this expensive has cheap plastic parts that constantly break. Very frustrating! Its a weekend, so KitchenAid is not open and Ill have to wait til Monday to see if they will do anything for me.
Published: July 25, 2015
Greg of Catonsville, MD
Source: consumeraffairs.com

KitchenAid KUDS30IXBL - Horrible product, barely worked right from day one.
KitchenAid KUDS30IXBL - Horrible product, barely worked right from day one. Never cycles through properly. I would recommend buying another brand than Whirlpool corporation products. Use the internet to find other brands. Whirlpool now owns/manufactures Kenmore, Maytag, Magic Chef, KitchenAid, among others. They are ruining these once great brand names. Read reviews, dont put up with it, find alternatives (LG, Samsung, GE all are superior quality durability) until they do something about their horrible quality and poor customer service. NEVER AGAIN, Whirlpool corp. I will not buy your products. For $630 I paid for this dishwasher I would expect 10 years service. Why make stainless steel inside and racking when all the rest of the components are so cheap, shoddy, they function for less than 6 months under normal to light use?
Published: March 8, 2014
wILL of Upstate, NY
Source: consumeraffairs.com

If youre thinking of buying KitchenAid major appliances, read the letter I
If youre thinking of buying KitchenAid major appliances, read the letter I recently sent to KitchenAid below. I got a legalistic form response offering nothing, not even an apology. They even got my name wrong. Never again.I am writing about a series of problems I have had with several large KitchenAid appliances. I have never written a complaint letter before, but the coincidental problems with your products reminds me of the planned obsolescence complaints from 30 years ago about American made cars. I thought about just posting all of this on the internet, but thought I should give you a chance to respond first. Here is my story. On December 2, 2004, I bought three major KitchenAid appliances as a part of a high-end kitchen renovation. A built in refrigerator was the big ticket item, but I also bought a gas stove/electric range, and a silent dishwasher, all brushed silver. Together, the three items cost me $11,494.35.Everything worked fine until this past spring, but within six months, all three appliances have had major problems. The compressor on the refrigerator failed. You covered the parts, but I paid over $600 in labor. A hinge on the door of the dishwasher rusted out, and I replaced it for over $300. Currently, the washer motor on the dishwasher is screaming every time it runs. Ive been quoted a cost of about $500 to replace it. What about the stove? This past summer the small control board (near the dials) failed, and I had to replace that at a cost of over $400. Last week, the large control board misfired, turning the oven my 16-year old daughter was using to make cupcakes on to clean mode, locking the door, setting the cupcakes on fire, and sending plumes of smoke throughout the house. Luckily, I was home from work with an injury, and thought to flip the circuit breaker. The fire died after about an hour, and the door opened when I put the breaker back on. I just replaced the big control board at a cost of over $500.All told, Ive paid over $2,200 to repair very expensive appliances that are less than 10 years old, and I still have a screaming silent dishwasher. How do you explain this? Planned obsolescence? If so, you certainly have the timing down pat. So why am I writing? I am hoping you will do the right thing by me and in making appliances that last. What is the right thing to do for me? Cut me a check for $2,200? Fix my dishwasher for free? Give me all new appliances and install them? Send me a letter of apology? Im not sure. I will leave that to you. I do hope someone responds. It might be cathartic for me to post a bunch of nasty reviews on the internet, but I hope there is a more constructive alternative.
Published: November 26, 2012
Robert of Charlottesville, VA
Source: consumeraffairs.com

The thermal fuse has blown out several times over the last two years, and i
The thermal fuse has blown out several times over the last two years, and is costing money each time. KitchenAid could care less - they are raking in the money as exclusive supplier of the parts. We have other Whirlpool and KitchenAid products, and the process is always the same. Theres no help from the company, no cheap parts, and theres aggravation at a simple machine that is designed to break down. Our Whirlpool dishwasher is designed with too small of a draincock, and it constantly blocks up. I am a repairman, and I am tired of coming home and fixing these ** things. I went over to Maytag and Sub-Zero, and have not regretted it. I now tell all of my customers and friends to not use these products as they will constantly be fixing them because they are designed to fail.
Published: October 27, 2011
Robert of Winnipeg, MB
Source: consumeraffairs.com

I will never buy or recommend KitchenAid products again! We have a $10K bui
I will never buy or recommend KitchenAid products again! We have a $10K built-in KitchenAid refrigerator that is only 4 years old. It has not been working for a month! Every time (9 so far) their certified techs come it goes over temperature again a day or two later. As a result I have had to throw out thousands of dollars of food, over a hundred ounces of breast milk for my 3 month old, wasted days now dealing with Kitchen-Aid and waiting for repairs, and had to endure this beyond frustrating experience just trying to get my fridge working. They should stand behind their products and their warranties and if their certified repair people cannot fix the problem, they should replace the product. Also, their customer service does not care, is not helpful, and is sarcastic. I am done!!
Published: September 24, 2016
Lauren of San Diego, CA
Source: consumeraffairs.com

This microwave is dangerous--turns on by itself. I called government consum
This microwave is dangerous--turns on by itself. I called government consumer safety report. I was the first to submit a complaint to government site. More people need to call to get this recalled. KitchenAid wont do anything even though this is the second time it has happened. First time was fixed by them because it’s on first year. I decided to call government site of consumer safety products.
Published: January 20, 2012
Jason of Burlington, VT
Source: consumeraffairs.com

Purchased extended warranty from Sears. Replaced electronics once already.
Purchased extended warranty from Sears. Replaced electronics once already. Out of warranty and now cost of repair is approx $1500.00 for a $2000 range. Replaced burners once also as they were not running as hot as specified.
Published: April 19, 2014
Mark of Kapaau, HI
Source: consumeraffairs.com

Bought the Kitchen Aid French Door Counter Depth (Model KBFS20EVMS9) from L
Bought the Kitchen Aid French Door Counter Depth (Model KBFS20EVMS9) from Lowes in Feb. 2012, and the 4 year extended warranty. It just started leaking on the floor, had the drain tube replaced. Leaking stopped but freezer is STILL forming ice inside. And I have no water feature or ice cube maker so I dont understand what the deal is. Maybe just a shoddy product? Another service call is scheduled. I get a feeling this isnt the last of it. I may end up hiring two strong guys to haul it down to Benton Harbor Michigan and dump on their front doorstep.
Published: September 2, 2014
deb of Holland, MI
Source: consumeraffairs.com

Had a new KitchenAid dishwasher installed a little over 5 years ago. Notice
Had a new KitchenAid dishwasher installed a little over 5 years ago. Noticed about 6 months ago that the top racked dishes were not getting cleaned. Then about 2 months ago noticed the bottom rack is starting to rust out. Called KitchenAid customer service today 6/23/15, gave them the model number and was told that it was just over 5 years old and it only comes with a 5-year warranty and they would NOT do anything (including discount parts) to correct this. Needless to say I WOULD NEVER PURCHASE ANYTHING from this company again. I will be going out of my way to review this company whenever given a chance.
Published: June 23, 2015
TONY of Little River, SC
Source: consumeraffairs.com

Five years ago, we fully remodeled our kitchen with all KitchenAid applianc
Five years ago, we fully remodeled our kitchen with all KitchenAid appliances including ice maker, side-by-side refrigerator, cooktop and wall oven/microwave, all supposed to be the top of the line. We have had nothing but problems with everything except the icemaker. Junk! We have just replaced both refrigerators with Samsung and we are looking for a new oven and cooktop, both of which died this past weekend. Junk! My sister and a close friend have the exact story. KitchenAid is junk!
Published: January 2, 2013
Craig of Alabama, AL
Source: consumeraffairs.com

The oven is a 1 1/2 old, and the enamel is peeling away. I am afraid that K
The oven is a 1 1/2 old, and the enamel is peeling away. I am afraid that KitchenAid is not going to take responsibility in this, and apparently this has happen to other people. What action can I take??
Published: July 7, 2015
maria of Naples, FL
Source: consumeraffairs.com

I purchased an Architect Series II gas range in July 2009. The range is in
I purchased an Architect Series II gas range in July 2009. The range is in a home that is inhabited only part time and has not been used much. In fact, it has probably been used a total of twelve times in two years. The first time that I used the self-clean function, the digital control panel went blank and the oven door remained locked. This occurred after about 1.5 hours of the self-clean cycle. I have researched this issue and discovered that it is an exceedingly common defect. Although this is marketed as a self-clean oven, it can never be self-cleaned without the risk of damaging a fuse that controls the control panel. When I contacted KitchenAid, they acknowledged that this defect has been recognized and repaired, but that my model and serial number do not fall within the recognized group of defective products. My product is an Architect Series II gas range. The numbers associated with it are KGRS807SSS and XY0202920. I have attempted to get KitchenAid to address the problem, but, as described above, they claim that my product falls outside the range of those that are defective. My problem is purely coincidental, although there are many similar complaints regarding the same product listed here.
Published: November 22, 2011
Elizabeth of Sebastopol, CA
Source: consumeraffairs.com

My dishwasher was purchased in November 2012. After having the repairman ou
My dishwasher was purchased in November 2012. After having the repairman out several times to fix top rack and a few other things, now am unable to use top rack as the arm is no longer rotating and dishes are not clean in top rack and am only able now to wash dishes in bottom rack. The dealers repairman said he could nothing wrong the last time and charged me $50 even though it is still under warranty from dealer. I am so disappointed in this dishwasher to the point of tears and frustrated no one can tell me the problem. Am following all the guidelines, turned up water temp, use cleaner once a month, rinse aid, etc.
Published: July 9, 2014
Rhonda of Oakwood, IL
Source: consumeraffairs.com

I've owned my slide-in KitchenAid range for 13 years. In all these yea
I've owned my slide-in KitchenAid range for 13 years. In all these years I've had no problems whatsoever. I use it daily and it still looks like new. I'd highly recommend this product!
Published: February 5, 2017
Chris of Livingston, TX
Source: consumeraffairs.com

Kitchen Aid stainless steel build in microwave model KBMS1454. I do like th
Kitchen Aid stainless steel build in microwave model KBMS1454. I do like the door that opens down rather than swing out. Has a cool down fan that seems to run a long time, although I have never had a microwave with a cool down fan before. Cooks food evenly and quickly.
Published: December 14, 2015
Mark of Riverside, CA
Source: consumeraffairs.com

I installed a KitchenAid Dishwasher KUD101FL SS3, Type 577-0, during my rem
I installed a KitchenAid Dishwasher KUD101FL SS3, Type 577-0, during my remodel. I have to wash the dishes before I put them into the dishwasher or they leave dried food on them. The cable pulley broke and came crashing down on my leg. The door is very heavy. I was very fortunate that I was bruised rather than fractured. Also, there was a very loud clashing noise when the blade goes around. Now, I am not using it at all and must call a repair person. Of course, it is no longer under warranty. What a shame that I paid so much for a worthless appliance.
Published: November 6, 2011
Irene of Laguna Niguel, CA
Source: consumeraffairs.com

I purchased this dishwasher about 5 years old based on the BEST BUY rating
I purchased this dishwasher about 5 years old based on the BEST BUY rating from Consumer Reports. What a mistake. I have had at least 4 issues with the left side of the top rack coming off the rails or leaning which causes the dishwasher not to start. The first time it happening the dishwasher was under warranty and the service guy said that this happens often with this model. Why has KitchenAid not recalled this machine?
Published: May 19, 2016
Debbie of Centreville, VA
Source: consumeraffairs.com

The door of my stainless steel dishwasher looks horrible. Streaks down the
The door of my stainless steel dishwasher looks horrible. Streaks down the front and spots that wont wash off. My other appliances wash off with just soap and water. I can not get the dishwasher clean and it isnt even a year old. I am so disappointed.
Published: June 13, 2014
Deborah of Fortson, GA
Source: consumeraffairs.com

Our KitchenAid dishwasher was purchased about two and a half years ago. The
Our KitchenAid dishwasher was purchased about two and a half years ago. The model is KUDS301XSS1 for over $1000 from HH Gregg Appliances. One and a half years into its use, it had a repair for $215 for a $30 fuse. The rest was labor because nothing on the dish washer would operate. The compartments that hold the knives, forks and spoons in place are held up on the sides of the utensil tray by bread twiggies to keep them from constantly falling into the respective sections. If anyone is experiencing this problem, the twiggies have been working now for over a year. The bottom panel which is plastic is held to the metal frame with cheap plastic that breaks. It is now held on by, you guessed it, another bread twiggie. Last week, the roller on the upper rack broke off of the cheap plastic spindle that holds it to more plastic parts on the rack. Now it is engineered by an ingenious screw washer fed by a strong plastic tie through a small washer fed through the opening of the roller and twisted onto the plastic frame on the upper rack. This works as long as one doesnt force the rack open. One should note that the end stops on the rack are made up of more cheap plastic parts that are quite fragile and will probably break in time. The dishwasher does clean dishes and is silent, but the cheapness of all these parts leaves me with one opinion - KitchenAid and Whirlpool do not care about making a good appliance. The KitchenAid was a replacement for two previous Whirlpools that gave decent service. I sold appliances in the past and know that KitchenAid made by Hobart was quite a top of the line dishwasher. My advice now - not worth the purchase price, not worth buying so let buyer beware. Because of this atrocious record, the rest of the new appliances in our kitchen went to Frigidaire. I have read many other complaints from others on the internet about this fuse that keeps going out. My repairman left the instructions for replacement so I can do it myself.
Published: January 5, 2014
Ronald of Fort Mitchell, KY
Source: consumeraffairs.com

My KitchenAid model# KFEG500E does not hold the correct temperature for mor
My KitchenAid model# KFEG500E does not hold the correct temperature for more than 20 minutes before it drops 15 to 20 degrees. It is near impossible to bake anything and have it be done at the correct time. I am shocked that the KitchenAid brand is so inferior to what it once was. My old KitchenAid oven served my family for 36 years before it finally died. My KitchenAid dishwasher is still going after 37 years and hope it lasts a little longer as I hate to see how bad the new ones are. It sure will not be a KitchenAid!
Published: November 17, 2018
Jeanne of Charlotte, NC
Source: consumeraffairs.com

I had an issue with the icemaker (not making ice). I called KitchenAid and
I had an issue with the icemaker (not making ice). I called KitchenAid and technician came out. He stated he needed to order a part. We left for the weekend, came back and because the technician did not restart the refrigerator, we lost everything in the refrigerator and freezer. That was 3 months ago and icemaker is still not fixed.
Published: June 25, 2013
Janice of Corona, CA
Source: consumeraffairs.com

I purchased three appliances from KitchenAid - a dishwasher, gas range and
I purchased three appliances from KitchenAid - a dishwasher, gas range and a microwave. The microwave died and I had to buy another brand. The dishwasher had to have the panel replaced within a few months of use (fortunately under warranty then). The gas range KAID KSGA906PSS00 has had nothing but problems. The “Gas probe on” message problem is perennial even though I never use it. I have to reset the fuse switch off and mimic the probe as if I was cooking.The control panel died last year and I had to pay $303.45 to get it changed. Now a few months later, the oven does not shut off; I get the Cooking complete message which refuses to go away and I have to reset the fuse switch. Perennial problems - paid a hefty amount on this set of KitchenAid junk. Wish I had chosen another brand.
Published: May 24, 2013
Y of Brookline, MA
Source: consumeraffairs.com

I have two pairs of the dishwasher drawers with custom wood panels and one
I have two pairs of the dishwasher drawers with custom wood panels and one pair started to make loud whirring noises and then would beep incessantly, resulting in us turning off the breaker switch to get it to stop. Then, the bottom drawer stopped draining and held water in the tub all the time. The repair man quoted me over $900.00 for the repair. He suggested that I not repair it, and I agreed with him. Now, my second pair is making loud noises and I am afraid it is on its way to death as well. I am so disappointed in these dishwashers. I am going to start a Facebook group to see how may others have defective dish drawers.
Published: March 24, 2012
Lisa of La Canada, CA
Source: consumeraffairs.com

We purchased a Kitchenaid model KUDS301XBL4 dishwasher about 2 years ago. I
We purchased a Kitchenaid model KUDS301XBL4 dishwasher about 2 years ago. It appears that the plastic inside the tub is deteriorating and the pegs that hold the rollers for the top rack have broken. I have found this is a common complaint among Kitchenaid dishwasher owners. The parts cost for the repair is about $28 per side plus shipping costs. I did send an e-mail to Kitchenaid explaining the problem and asking them what their solution is regarding the defective parts. No reply at this time. I dont expect them to acknowledge defects or offer a solution based on other complaints I have read . So, I took to finding a solution myself.I examined the mechanism and figured out how it works and had an idea that if I could find the right nylon and stainless steel parts at my hardware store, I could re-install the rollers on a different spot on the sides of the rack. I found all the parts for the four rollers for a total of $7.89 and proceeded with installing them. I had to use a Dremel tool to cut the broken roller pegs off and sand a small plastic ridge flat. I drilled holes and assembled my parts and attached them successfully to each side of the rack (see picture). For each roller, I used a stainless steel screw, washer and lock nut along with a nylon finish washer and a nylon bushing. It works great!It is too bad that Kitchenaid wont stand behind their product, as evident in other, similar complaints. I am not an engineer, but I engineered a solution in one-hour that will last longer than the rest of the original plastic parts in the tub.
Published: November 24, 2013
Christopher of Pendleton, OR
Source: consumeraffairs.com

Purchased a KitchenAid Dishwasher model #KDFE204EWH2 and after 18 months ne
Purchased a KitchenAid Dishwasher model #KDFE204EWH2 and after 18 months needed to be repaired at the cost of $311. The Sump & Motor assembly unit needed to be replaced. I purchased a KitchenAid because my last KitchenAid dishwasher lasted for 25 years. Very unhappy with my new dishwasher.
Published: March 23, 2018
Holly of St Petersburg, FL
Source: consumeraffairs.com

We decided to purchase a Kitchen Aid dishwasher (KUDC10FXSS) to replace our
We decided to purchase a Kitchen Aid dishwasher (KUDC10FXSS) to replace our Whirlpool dishwasher in the spring of this year. We have had nothing but problems with it. I noticed that it was running through rinse aid very quickly and then completely shut down. We were told that it needed a new control board, which was then replaced. It took three weeks to get this part in because it was on back order. Less than a week later, the rinse aid began pouring out from the dispenser, so once again a repairman came out and told us that we must have a bad dispenser so that was replaced next. Even with the new dispenser, I am now having to add rinse aid every two weeks and have a terrible film on my glasses and dishes. I called the business where we bought it and they sent out the same repair guy, who told me that he doesnt know why its going through rinse aid so quickly and that he would research it for me. Well, its been three weeks and no word from him or the business which he works for. We asked to replace this dishwasher because we think its a lemon and we were told that unless we have three separate incidents with it, Kitchen Aid will not replace it. We are very frustrated and will not buy any Kitchen Aid products in the future!
Published: October 24, 2011
Ginny of Schwenksville, PA
Source: consumeraffairs.com

Just had the service man leave the house after determining that my 5-year-o
Just had the service man leave the house after determining that my 5-year-old built-in KitchenAid fridge was not working because of a malfunction in a now obsolete computer board. Only option is to wait weeks for a refurbished board which may or may not work and for how long, no one knows. Not very much choice as this fridge had custom panels made to match the kitchen cabinetry and the panels will not fit any other fridge. After reading the reviews on this site I see that this is a very common problem. I have always purchased KitchenAid - thought they were reliable and reasonably priced - no more. Clearly KitchenAid is a brand name which stands for nothing in the way of reliability and durability.
Published: August 29, 2013
Louise of Maple Ridge, BC
Source: consumeraffairs.com

I am a semi retired senior that saved to purchase my last (what I thought a
I am a semi retired senior that saved to purchase my last (what I thought at the time) kitchen range. I have owned KitchenAid ranges in the past and have been very pleased. There were two reasons I purchased this particular brand, it doesnt make any fan noises and for the self cleaning system. To my delight the stove is very quiet and allows an option to turn off all the normal beeping noises and the elements work well. That being said I have never been so disappointed with an oven cleaning system, it DOES NOT WORK AT ALL and yet the company continues to produce this system misleading the public. To me this is a criminal offense except I have no way to make them accountable. I am so disappointed with KitchenAid that they would associate themselves with such an inferior product. It is crucial for me to have a self clean oven and as one of thousands I am now stuck with a product I have come to hate in my kitchen. I am an avid cook and now find there are many products I am unwilling to cook as I have no way to clean my oven. I made wonderful Yorkshire puddings the other night and my husband spent two hours trying to clean the oven but the interior is so shoddy (not really a porcelain coating just some cheap material that cant withstand a proper cleaning and wont come clean with water being heated to 200F doesnt matter how many times you try). The first time after I used the self clean (I have only had the stove for 4 months and cleaned it 5 times) I sat down and cried, having spent so much money and having so much disappointment was a bit overwhelming. I called the place I bought it, they are really great, said the only thing they could do was to sell me a different stove at cost. I appreciated that but I now dont have the funds to do this or I would just to get rid of my stove. I have an extended warranty but this is not considered a warranty issue. I really have trouble with KitchenAid not standing behind their product but more so with a problem they know exists but keep producing, and as consumers we seem powerless to enforce change. As a side note, the oven wasnt hot enough and it does have an option to calibrate the temp. but even so because the oven is not well insulated or made of quality porcelain. During the cooking the temp. can drop as much as 50 degrees before it heats up again which can really affect the cooking process. So all around in general not very happy.
Published: November 8, 2018
Beth of Canada
Source: consumeraffairs.com

We contacted Whirlpool directly and they were amazing. We are getting a ne
We contacted Whirlpool directly and they were amazing. We are getting a new refrigerator. Deal with Whirlpool, not Kitchenaid.
Published: January 1, 1970
Leah of Hayden Lake, ID
Source: consumeraffairs.com

This fridge was over $3,000. It took 4 different repair calls to line up dr
This fridge was over $3,000. It took 4 different repair calls to line up drawers. For a few months it has been shutting itself off for several hours 2 or 3 times a week. 2 days ago it shut off and wont come back on. Light above water works. Lights inside dont. I bought 4 KitchenAid appliances at the same time 4 years ago. They do not care once the sale is made.
Published: October 20, 2019
Charlene of Clarksville, OH
Source: consumeraffairs.com

Bought a KitchenAid model # kffs20EYBL00 in 2012. This refrigerator has giv
Bought a KitchenAid model # kffs20EYBL00 in 2012. This refrigerator has given me nothing but grief since 2012. I bought an extended warranty on this refrigerator and glad I did, have had to use it numerous times. The back of the freezer will freeze up, makes this running noise that sounds like a motor is running and the upper refrigerator isnt as cold as it should be. They have had to repair this 5 times in 2012 to 2013. 2014 and 2015 probably 2 times and now 2016 we are getting repaired once again. I am very frustrated with this refrigerator. I not only have had issues with the freezer, but the shelving in this refrigerator is junk.I have had two shelves break so far. Its just junk! I dont recommend KitchenAid anymore. Maybe in the 80 and 90s this was a good brand but not any longer. Looking at buying a new one, hate too since this one cost me of $1600.00 and 4 yrs of grief. Stay away from KitchenAid and Whirlpool. They are made by same company from what I have been told by companies I am looking at for a new refrigerator!
Published: October 30, 2016
Tracy of Duncansville, PA
Source: consumeraffairs.com

I had my oven in the medium setting to clean, but was not in the kitchen at
I had my oven in the medium setting to clean, but was not in the kitchen at the moment when we heard a very loud noise that sounded like an explosion. Immediately thereafter, shattered glass was falling out everywhere it could come out of. Very frightening moment. Called KichenAid in the morning and explained everything. They will send someone out tomorrow and assess the situation. We just moved into this place six weeks ago. The day we moved here, the freezer was leaking and formed a sheet of ice on the bottom drawer. Here I was offered to buy one year of warranty and paid $320.00 for it. All appliances are KiitchenAid and were installed in September 2011. They are like new. I, of course, have no warranty on these appliances and think this is absolutely crazy that after short time for such expensive appliances, these things happen. I will report on how this explosion will be taken care of tomorrow!
Published: October 17, 2013
Stefanie of Glenview, IL
Source: consumeraffairs.com

We have had a French Door fridge by KitchenAid in March 2019. Today is the
We have had a French Door fridge by KitchenAid in March 2019. Today is the third service call on the freezer filling with frost, and the ice maker, which pours ice out at an unbelievable volume constantly. The ice maker has now been replaced twice, and the technician tried to blame me for its malfunctioning (because I love taking time off work to hang out with him, I guess?). The door has rust spots all over it (which he has used my baking soda and vinegar to attempt to clean), and he told me today that part of the motor sounds like its going to need to be replaced, too. Customer service is like a Kafka story...theres no way to replace what is clearly a defective item until its deemed unrepairable, but theres also no rule about how many repairs/replacements will deem something unrepairable. I just know my warranty will end up running out before they replace the item. Im so deeply disappointed because something like a brand new fridge doesnt make it into my life very often, and thinking that Ive wasted my money on a clunker that will continue now to waste my time & money is heartbreaking. I wish the company will take responsibility for their product and stand behind it when it doesnt work properly.
Published: January 24, 2020
Roxanne of Toronto, ON
Source: consumeraffairs.com

I have had to replace my top light in my refrigerator twice already. Well t
I have had to replace my top light in my refrigerator twice already. Well today I opened the refrigerator to clean and once again smelled a burning plastic smell. Yep, looked up and the lights had fallen again and was melting the plastic that covers the top light. This is a huge fire risk. Thank God I have caught it all three times now before it starts a fire. KitchenAid will be getting a call from me first thing in the morning. My parents always purchased KitchenAid products and I have up until this point. Guess its time to find a new family brand that will be safe to have in our home. I would not recommend a KitchenAid refrigerator to anyone at this present moment.
Published: August 18, 2013
Renee of Manassas, VA
Source: consumeraffairs.com

Our KitchenAid model KUDD01DSSS stainless steel dishwasher is a double draw
Our KitchenAid model KUDD01DSSS stainless steel dishwasher is a double drawer unit with plastic interior. It is very nice for my wife and I and small loads but probably not as useful for a family. It is a bit noisy and seems to run quite a long time. This is a 2006 model, so perhaps a newer model would be more efficient and address the noise issue. Overall, I have been satisfied with this dishwasher.
Published: January 8, 2016
Keith of Raleigh, North Carolina
Source: consumeraffairs.com

Our 18-year old KitchenAid refrigerator had been working just fine until th
Our 18-year old KitchenAid refrigerator had been working just fine until the ice maker failed. We had a new one installed. That one failed (actually never worked at all). Considering the age of the refrigerator, we decided to just replace it. We bought a new $2,500 KitchenAid side-by-side, water and ice in the door, refrigerator. Guess what? The ice maker did not work. I had a replacement put in. Also, it did not work. Four KitchenAid ice makers in around two months, is anyone at KitchenAid addressing this problem? Do you think just maybe there is a problem in manufacturing? If this problem cannot be resolved, the refrigerator goes back and I am buying another brand and will never buy another KitchenAid product again. Sadly, I was told that KitchenAid was top of the line. Heaven help us all if this is what is considered top of the line.
Published: May 16, 2012
Adele of Mattapoisett, MA
Source: consumeraffairs.com

Dishwasher is 2 years old and has had 11 wheels replaced on the top rack. U
Dishwasher is 2 years old and has had 11 wheels replaced on the top rack. Utensils always go through the holes in the utensil holder, often many while its running, and they get stuck and you cant even move the rack to try and get them out. Almost have to climb into the dishwasher to reach the ones at the back, which is of course after spending almost an hour trying to get all the other dishes out of the bottom rack with the top rack in the way. And forget about actually filling it, neither rack can hold any weight. The top one cant handle 5 glasses from dinner and 2-3 bowls without bending. Its not like anyone would expect a dishwasher to be able to handle the weight of I dont know... DISHES!!! If it was up to me I would leave it at the store front entrance. They can deal with this piece of **.
Published: August 3, 2015
S of Vancouver, BC
Source: consumeraffairs.com

KitchenAid dishwasher kud530fxss4 constant repair. Thermocouple went out, r
KitchenAid dishwasher kud530fxss4 constant repair. Thermocouple went out, repairman replaced. 6 month later out again. Replaced with modification recommends by manufacturer. 7 months later out again. Replaced again. Now circuit board fried. Appliance is not worth the price. I have had dishwashers costing half as much last years. Will never buy KitchenAid again. Dishwasher is 4 years old and going to the trash bin.
Published: December 27, 2016
Steven of Burleson, TX
Source: consumeraffairs.com

Operationally this is a nice-looking, relatively quiet, efficient machine w
Operationally this is a nice-looking, relatively quiet, efficient machine with multiple modes of operation. Where it falls from grace is the isolation of the top/hidden electronics from the moisture of a functioning dishwasher. The replacement by the owner is not out of the question, but most users wont do this. The main control board can be replaced by unplugging a socket after the front of the machine is removed. One other drawback is the spring and cord mechanism that balances the weight of the door, it can break more than once in a 20-year operating lifetime. On the good side this unit is still working after 20 years whereas many others are broken and replaced. The motor, pump and dish/silver racks are all working and in good condition. The inside and outside stainless is fully functional and easily cleaned.
Published: February 13, 2021
Chris of Point Roberts, WA
Source: consumeraffairs.com

Bought fridqe 5/30/13. First Geek squad guy was at our home in August due t
Bought fridqe 5/30/13. First Geek squad guy was at our home in August due to water dripping inside fridge. Geek squad was out at least 7 other times, replaced everything inside stove too (kept turning itself off). Bought extended warranty from Whirlpool, but not really whirlpool. Assurance is extended warranty company? Started sending AAA appliance out, theyve replaced everything inside at least once, some twice. Still doesnt make ice and leaks. They call whirlpool but apparently should be calling Assurance. AAA can’t fix it, told whirlpool it needs to be replaced. Assurance knows nothing about it? What a nightmare. Ill never buy whirlpool again. Just want what I paid for!!
Published: November 21, 2014
kevin of St Charles, MO
Source: consumeraffairs.com

KitchenAid 30 free standing gas range with double oven bought. Beautiful to
KitchenAid 30 free standing gas range with double oven bought. Beautiful to look at BUT! Have had less than a month and many problems. First gas leaks (they were repaired). My one time to use: baked an apple pie in bottom oven. Preheated to 450, baked pie for 15, then reduced to 350 for 45 minutes. During this time the vent blew so hard on top right burners, it got the top range very hot and impossible to use right burners (vent blew the flames... dangerous). Also top right side got extremely hot... not operating correctly at all. Now dealing with Whirlpool Corp Safety Dept to get them to take this range back... scares me to even think about using it... NOT using it... it is a lemon!!! They say must process/have evaluation by technician and then 3 to 4 weeks to process. BS!!! The order # is the no. with Whirlpool Corp Safety Dept. 553 Benson Road, Benson Harbor, Michigan 49022.
Published: October 5, 2017
Dorothy of Blue Ridge, GA
Source: consumeraffairs.com

I had both fridge and stove replaced as we threatened to take them to court
I had both fridge and stove replaced as we threatened to take them to court. Well, we should have asked for our money back. Our 9 year old KBRS22KMSS $3500 fridge died and though KAid will replace compressor, it will cost $500 in labor and will not guarantee it will fix issue. To top it all off, the service man snickered as he looked at our $5700 pro series oven as he was leaving and commented on how many issues they had and the parts are not available so off to the scrap yard. I will never buy KA, WHIRLPOOL, AMANA, MAYTAG OR JENNAIR products ever again.
Published: July 15, 2014
M of North York, ON
Source: consumeraffairs.com

We are extremely careful when we use these ovens. Regardless, we have repla
We are extremely careful when we use these ovens. Regardless, we have replaced the door hinges six times in the past two years and the blower fan once. If I clean the oven, the doors lock and remain locked when completely cool. This has happened numerous times, also. This is a high end appliance that is junk!
Published: April 9, 2014
Debbie of Aurora, CO
Source: consumeraffairs.com

I purchased an oven, built in microwave, downdraft stove, ice machine, dish
I purchased an oven, built in microwave, downdraft stove, ice machine, dishwasher and refrigerator. So far the oven has gone out when I cleaned it. It burned up. I had to threaten a lawsuit to get a repair person to fix it for free. The microwave has missing pieces of the time. It needs a new board. The ice machine is completely dead. My appliances are THREE years old. I have never ever seen such poor quality in my life. The very last time I will ever purchase KA.
Published: August 28, 2018
Jan of Bethany, OK
Source: consumeraffairs.com

We installed this KitchenAid (kbfs25ecms) fridge just two weeks. We find th
We installed this KitchenAid (kbfs25ecms) fridge just two weeks. We find that the door alarm was suddenly not function and the freezer temperature has problem as well. We try to book the appointment and email to them but their website always has error and no any customer service response to you. I never to check the consumer affairs website before, otherwise I will pay attention on this brand. Hope other customers dont reliance on the KitchenAid past images. Bless you all.
Published: April 15, 2015
Tommy of Markham, ON
Source: consumeraffairs.com

This dishwasher replaced an old Kenmore one, and the KitchenAid cleans so m
This dishwasher replaced an old Kenmore one, and the KitchenAid cleans so much better and is a lot quieter. I also like the styling with the sleek front and no huge buttons sticking up. Would highly recommend the Kitchenaid brand.
Published: March 20, 2020
Jenny of Middle River, MD
Source: consumeraffairs.com

KitchenAid Superba Electric Double Ovens - We recently purchased the above
KitchenAid Superba Electric Double Ovens - We recently purchased the above ovens. They have never worked correctly. There have been four or more service calls. They have replaced the sensors twice. They have replaced the mother boards twice. Each time, the serviceman is hopeful the repairs will work. They have not. Last night, the lasagna took 50% longer to cook as our guests waited. We discovered the oven was actually at 345 rather than the 400 it was set at. A call to KitchenAid was of no help. They said they had a record of only one service call and seemed very unresponsive. A bad product with worse service!
Published: May 1, 2012
Robert of San Antonio, TX
Source: consumeraffairs.com

Knobs break easily and are costly to replace. Approximately $30 dollars to
Knobs break easily and are costly to replace. Approximately $30 dollars to replace. Two have already broke. Thinking of replacing the stove even though it works well otherwise. I see that others have the same issue. KitchenAid how can you help us. The product in general is good but the knobs with steel overlay have plastic where it attaches to the stove panel and it is of substandard qualify.
Published: February 25, 2015
Andrea of Toronto, ON
Source: consumeraffairs.com

I have a KitchenAid build in refrigerator that is 9 years old, the board ne
I have a KitchenAid build in refrigerator that is 9 years old, the board needs replacement. I called Whirlpool (owns Kitchenaid) and after their service provider came in they diagnosed that the board needs to be replaced. Here is where the problem starts and the reason of of my 2 star review. They informed me that the part if not available, that they have no idea when it will be available, and that they can not provide a date or any other resolution. Basically what they told me is your 9 year old $8,000 product can stop working and we do not care if we produce the parts to service it anyone.Please do not buy any product from a company that cannot produce the parts to fix it after only 9 years. I know the time seems like a long life, but 9 years life for a $8K product is not a reasonable expectation. Last the customer service is very poor, representative refused to escalate, or provide any other resolution. They really do expect that I have to accept a no working refrigerator while I am waiting for some magical date to resolve the issue on a part that they do not produce anymore. I do not recommend the product. Companies should stand behind what they produce and provide the parts to service it (not for free I am happy to pay).
Published: March 23, 2021
Yannis of Palm Springs, CA
Source: consumeraffairs.com

Bought a complete line of KitchenAid products for a remodel job on my kitch
Bought a complete line of KitchenAid products for a remodel job on my kitchen a year ago. Purchased the products in April 2017 but did not install them until the first part of June. The KRSC503ESS side by side, counter depth refrigerator does not cool properly. In December 2017 I notice the refrigerator was warm and the bottom drawer was not going in all the way. There was an ice build up at the back of the refrigerator. Also, the freezer was not cooling properly. Call for service and they replace a fan motor and thermistor. The unit seem to be working fine until this week. Same problem. Pulled everything out and turned the refrigerator off for 24 hours to let it thaw out. Turned it back on and everything is working fine again. I personally feel there is a bad design in this unit. The bottom doors are against the cooling unit in the back of the refrigerator. I feel this will continue forever.I call for service again and now KitchenAid and the extended warranty company are saying its not their problem. The KitchenAid service said that I might be responsible for the service call if they come out and find it is not a warranty issue for them. Additionally, the ice maker makes loud noises when it dumps the ice in the ice container. It does wake me up at night. I thought KitchenAid was suppose to be the higher end of appliances, but boy, was I wrong. Hindsight being 20/20, I should have done my homework a lot more. Never again.
Published: May 5, 2018
Ken of Haslet, TX
Source: consumeraffairs.com

An unusual problem occurred with my 1999 refrigerator. A screw broke inside
An unusual problem occurred with my 1999 refrigerator. A screw broke inside one of the back wall brackets that hold the shelves. I called KitchenAid for an authorized factory dealer thinking their experience would know how to resolve the problem. KitchenAid informed me the cost to send someone would be $129 plus parts, and if the tech stated it could not be repaired, they would offer something towards the purchase of a new refrigerator. The tech was not able to get the broken screw out of the bracket. I called KitchenAid in his presence, and they refused to stand by their original statement. The tech called his employer, A&E Service Co. and was told to do the best he could. He claims he inserted another screw near the broken one and put tape across the top and bottom of the bracket to hold it. He said this is a temporary repair that might last 3 months and then I would have to buy a new refrigerator. A&E charged me $166.20. I complained stating that wasnt the quote I received, and the tech was not able to fix the problem. They said they will reimburse me $26. I feel because the refrigerator was not able to be repaired, I should be reimbursed the full amount (A&E Factory Service, 35 Melville Park Rd, Melville, NY 11747, tel.# 800-905-9605). The tech arrived on January 7. I spoke to KitchenAids repair department, customer service, and the sales department stating what I was initially told about partial compensation towards a new refrigerator. Each department refused based on the year of the appliance. This is a very unusual matter. The tech noticed only very light items are placed on the 2 shelves involved. He said he never saw anything like this in all his time as a repair person. He noted it wasnt weight that caused the bracket to separate from the back wall. Am I entitled to a full reimbursement from A&E since they could not fix the refrigerator and I will eventually have to buy a new one? Is KitchenAid responsible in any way?
Published: January 11, 2013
Elaine of New York, NY
Source: consumeraffairs.com

My 1-year-old electric steam oven (KEBU107SSS03) blew the inner glass on se
My 1-year-old electric steam oven (KEBU107SSS03) blew the inner glass on self-clean mode. This was the first time I ever used the self-clean mode. I followed the instructions in the manual on self-clean in detail. The mode was set to regular and time given was 3 hrs 30 min. After 1 hr., I heard a loud explosion. The inner glass was shattered. I now await what KitchenAid will do.
Published: December 27, 2012
Rajiv of Trinidad, OTHER
Source: consumeraffairs.com

After having a KitchenAid dishwasher that ran well for 11 years, we purchas
After having a KitchenAid dishwasher that ran well for 11 years, we purchased a KitchenAid dishwasher from Sears on 6/11. This was model KUDS30FSSX2. In November of 12, wheels came off the upper rack and soon after, the motor wouldnt start. It would hum and then not go further in cycle. We had a repairman look at it. He said the motor was bad and that KitchenAid would not replace it. We paid for a replacement (about $400). The wheels on the upper rack were replaced after we complained to Whirlpool. There was never one trip here. They had to call for parts which were sent in about a week. Now, the motor will again not start and we are waiting to get help again. We never talk to the same person twice. The reports above match our experience. This is the same experience we had many years ago with our SAAB auto. They of course are now out of business and their employees lost their jobs. Im sure the execs were well compensated. KitchenAid and their owner, Whirlpool, are headed for the same future. I feel sorry for the employees, but this is what will happen when quality and buyer satisfaction no longer counts. Needless to say, we will never purchase another KitchenAid product or a Whirlpool made product which are marketed under names like Kenmore, etc. Sears too has been no help.
Published: February 10, 2013
T John of Sherman Oaks, CA
Source: consumeraffairs.com

Kitchenaid ktrs19k - The inside of the freezer burnt to a crisp around the
Kitchenaid ktrs19k - The inside of the freezer burnt to a crisp around the light encasing. It melted the sides of the fridge and charred the side wall. This is very disturbing to know; this could have burnt down my house. Has anyone heard of this before? I, too, had a house full of KitchenAid and guess what? They have all been replaced. Now, the refrigerator is dead. NEVER AGAIN!
Published: July 8, 2013
Lea of Charlton, MA
Source: consumeraffairs.com

In a nutshell, the same part on my fridge (the thermistor assembly) has bro
In a nutshell, the same part on my fridge (the thermistor assembly) has broken down 5 times since I bought it (roughly every three months) causing the fridge to simultaneously ice over yet not keep the food cold. I have a warranty on it, and per CAs Lemon Law, they should have replaced the fridge by now. But every time I call, they keep coming up with reasons why that it doesnt qualify for a Lemon replacement. (This latest time was that the latest repair had the same claim number because it was technically within 90 days of the last time a technician came out. By this logic, they could give me the same claim number till the end of time and never replace the fridge).I can afford a new fridge, but at this point its a matter of principle. I have wasted thousands of dollars in food, not to mention days of my life dealing with this issue -- and have become convinced (based on my research of other consumer complaints) that this is an issue KitchenAid is aware of and that they have knowingly foisted a faulty product & loophole-ridden warranty onto their consumers and EXPECT us to give up when they give us the run-around. I have researched lawsuits against KitchenAid and their warranty company and have been contacted by lawyers who are interested in pursuing a class action lawsuit. If you are interested in getting more information/participating in a class action lawsuit against KitchenAid, please email me.
Published: May 30, 2017
Adele of Los Angeles, CA
Source: consumeraffairs.com

One year and two months after purchase the refrigerator needed a new compre
One year and two months after purchase the refrigerator needed a new compressor, evaporator, etc. It was not cooling the freezer drawer. Certified repair required two visits to diagnose and then make the replacements. We were treated very poorly by the tech. Who refused to state if the repair was successful only saying lets wait and see. Over two hundred dollars’ worth of food spoiled. Compressor runs non-stop. Not sure if problem was solved and concerned that more problems to come. Disappointing experience that was a huge inconvenience.
Published: September 23, 2014
Peter of Denver, CO
Source: consumeraffairs.com

For the second time the transistor/computer board has malfunctioned. We bou
For the second time the transistor/computer board has malfunctioned. We bought the appliance in set 2006. After two months we had a terrible leak due to a faulty stab fitting in the water line. In Feb 2010 the transistor blew and was replaced. It happened again and now we need to get a rebuilt one, not new because of the tsunami knocking out the plant that used to make the parts. Why would I trust the part? Also they say turnaround is 48 hours, we will see. If it werent for the custom wood panels I have on the fridge, I would switch to a new brand!
Published: February 28, 2014
Patricia of Cranbury, NJ
Source: consumeraffairs.com

Built In Side by Side Purchased 1999. In 2000 the ice dispenser started lea
Built In Side by Side Purchased 1999. In 2000 the ice dispenser started leaking water and the panel in the door discolored. Thank goodness it was fixed at no charge after threatening to sue. Forward to 2016 refrigerator quit working and it took numerous visits to replace a fan, in the freezer, charge with Freon, replace the compressor, forward to 2017 and the refrigerator needed a valve replaced but the valve was discontinued (door from freezer left slightly opened). July 2018 same fan in freezer went out and had to be replaced. One year warranty on fan. I have a side by side Whirlpool from the late 80s and it runs like a top no problems!!!
Published: July 18, 2018
Gaston of Breaslton, GA
Source: consumeraffairs.com

I have a french door refrigerator (Model KBFS22ECMS00 purchase date 1/27/15
I have a french door refrigerator (Model KBFS22ECMS00 purchase date 1/27/15) and gas range (Model KGRS202BSS-1 purchase date 1/19/15) that have issues. I called 2 weeks before Thanksgiving about the freezer not maintaining temperature (set at -6 degrees, maintaining 6-15 degrees) at time of call. Several days BEFORE Thanksgiving, the refrigerator started doing the same thing (set as low as possible, maintaining 45+ degrees). On the day of Thanksgiving, my oven refused to maintain set temperature. It would get to temperature then the igniter failed to ignite the gas and maintain the set temperature. No smell of gas in the house.November 30 when service techs arrived, it was discovered my condenser leaked all the oil out and the compressor had locked up. They had to order parts. Had a service date of 12/16 to repair the refrigerator and troubleshoot the issue with the oven. Was called the day before by Video Tech Services (the servicing company) to cancel my service appointment because one of the refrigerator parts was on backorder. Called KitchenAid/Whirlpool early last week and lo and behold, THEY had the part that was on backorder so I have no idea where the service company is getting their parts from. Parts were sent to the service company 2 day shipping so they SHOULD have received it last Friday (12/18)... At the latest.I called KitchenAid/Whirlpool again on the Tuesday (12/22) since I had not received a scheduling call from the service company. Interestingly enough, the servicing company received the backordered part on SATURDAY (12/19) but had since FAILED to call for a service appointment. Now mind you, this is going into a SECOND MAJOR HOLIDAY without appliances. The service company finally called 30-45 minutes AFTER my call to the manufacturer. I am now scheduled for a repair on January 15 because I refused to take another day off from work (11/30) to accommodate them. I had taken the day off on 12/16 as well. Both appliances 10 months old (actually the refrigerator was 9 months old (delivery date of 2/22)) before failing and 60+ days before repair? Through two MAJOR holidays???
Published: December 28, 2015
Gene of Upper Chichester, PA
Source: consumeraffairs.com

We purchased a combination oven & microwave/convection oven in 2008, th
We purchased a combination oven & microwave/convection oven in 2008, the microwave recently began to not heat food and drinks. We notified KitchenAid and were referred to a local repair who diagnosed the problem and said it would require a new magnetron and control board, with labor the cost would be $650+, we decided the cost of the repair was much less than a new oven and microwave and committed to the repair. Repair was made, microwave now functions/heats food and drinks at a fraction of the previous level. Had repairman return today to diagnose and repair again. He proceeded to do test as dictated by KitchenAids factory tech on the phone with him, fill vessel with 10oz. of water, check temperature, heat for 30 seconds and check again. The difference was +20 degrees hotter which is the lowest level of their benchmark for acceptable being acceptable.Bottom line is it still doesnt heat as it did before the $650+ repair. I then spoke with rep at Kitchenaid for an hour expressing my displeasure and asking for help, their answer’s sorry but its a 10-11 year old appliance and they dont perform as well when theyre that old is the final word from them. My question to her was why didnt anyone mention that before we committed to the repair, she was silent on that. Sooo, I will not advocate KitchenAid as a quality product again much less purchase another of their appliances. I will advise others to look elsewhere when shopping for appliances! I have also filed a dispute with my credit card company in an effort to recover some of the cost we incurred.
Published: August 3, 2019
Dale of Fair Oaks, CA
Source: consumeraffairs.com

We recently remodeled our kitchen and because our old appliances were Kitch
We recently remodeled our kitchen and because our old appliances were KitchenAid and we were happy with them we decided to go with the brand again. Such a mistake. Within a few months the finishes on the fridge and the dishwasher are discolored, spotty, and there is rust showing through on the fridge door in multiple places. The handle on the freezer door wont stay tight. The self cleaning oven is a joke. These are overpriced, poor quality appliances. We bought an extended warranty which is no help for these issues. In spite of the fact that I was calm and factual with the resolution specialist was sarcastic and condescending. Im kicking myself for not doing more research as there are a ton of negative reviews out there stating the same complaints. I will share this story with everyone I can to be sure this product isnt purchased.
Published: May 15, 2019
Jennifer of Vista, CA
Source: consumeraffairs.com

We bought a dual oven Kitchen Aid True Convection Oven with Induction cook
We bought a dual oven Kitchen Aid True Convection Oven with Induction cook top (Model YKFID500ESS). We started noticing blue flakes in the rag when cleaning the upper oven. Then 2 weeks after the warranty was up the surface started flake away in the front edge of the bottom surface of the upper oven. When we contacted Whirlpool they said this wasn’t a recorded problem from anyone else and they would not be covering it. They told me they would have just used touch up paint even if it was still under warranty. We luckily had bought an extended warranty and when they came out the tech said it was not repairable. The warranty company covered it under their lemon clause. We then ordered another identical range to replace it thinking it was a one of problem. I checked out the new range before I accepted it and found the same issue with the surface in the same location already bubbling. We would not accept the range and had it returned to the store. I now have to contact the store and look for another option because I will never buy another Kitchen Aid appliance. Whirlpool needs to come clean about this issue and everyone with this model needs to take a close look at their top ovens surface.
Published: September 2, 2018
Mark of Nanaimo, BC
Source: consumeraffairs.com

Im a commercial dishwasher repairman. My 10-month old dishwasher failed, de
Im a commercial dishwasher repairman. My 10-month old dishwasher failed, dead, no lights, nothing. I checked the power and performed troubleshooting steps, determined the problem was a bad control board. I called the folks who sold it to me. They did not have a control board in stock. I asked that they bring a board with them so they could fix it with one visit. They said no, they could not be sure the board was the problem. I was going to have to wait 5 days (including Saturday & Sunday) for them to show up between 1 and 4, and then have to go through another wait until they were able to get the part. I am not very fond of washing dishes by hand, so I called around and found a parts place that could have the part by the next day (Saturday). The part came in and I installed the part, which fixed the problem. I called the dealer and canceled the service call and asked if it was possible to get any credit on the part. They said no, but I could call KitchenAid. I called KitchenAid this morning. No luck, it did not matter that Id saved them two service calls. It did not matter that I had taken the risk for the cost of the part if my diagnosis had been incorrect (with electronic parts, once the box is open, you own it). After speaking with Shari and David (a supervisor), KitchenAids policy is inflexible. If a customer touches it, they dont warranty it. In addition, they refused to send someone out to inspect my work or to confirm the board was bad. Im very disappointed! Heck, if they had offered to split the cost of the part or even to give me credit towards my next KitchenAid Appliance, Id have been thrilled. Instead, I was left with a bitter taste in my mouth.
Published: August 27, 2012
Forrest of Hampton, VA
Source: consumeraffairs.com

Bought a brand new Kitchenaid dishwasher from local Home Depot store. It wa
Bought a brand new Kitchenaid dishwasher from local Home Depot store. It was rated five out of five very expensive took the salesperson at Home Depot. After first wash realized not drying dishes and was leaking soap from bottom of door. Serviceman ordered four parts. A week later while we were waiting for part as we were using it stopped and showed two errors and water inside the unit. They said it was pump and part was not available though manufacturer. I requested from Kitchenaid for replacement. They said the warranty is only good for repair not replacing it. So now after eight weeks w/o dishwasher we have to wait for another three to four.
Published: August 11, 2020
Hooshang of Albuquerque, NM
Source: consumeraffairs.com

Kitchenaid Dishwasher KUDS301XBL7 - The plastic rollers on the top and bott
Kitchenaid Dishwasher KUDS301XBL7 - The plastic rollers on the top and bottom are cheap and break a couple of years. We have replaced 3 out of 4 roller assemblies and anticipate the 4th to go soon. Also, the controls on the front are very touchy. If you lean against the counter and accidentally touch the dishwasher/control board, it will turn on or start cycling. This forces you to lock the panel, but that is not convenient. Dishwasher works well and have no problems with it.
Published: June 18, 2014
Mike of Webb City, MO
Source: consumeraffairs.com

I want compensation for my problem with dishwasher. The inconvenience and f
I want compensation for my problem with dishwasher. The inconvenience and frustration of having an appliance that I can not trust. KitchenAids answer is to buy an extended warranty. How is that going to help when I never know if the dishwasher will work from day to day? They have replaced two door switches under warranty and I am out of warranty and I have the problem again. Am I to live with this every year two or more repairs for the same problem? My repairman is ordering another door switch. His opinion is they have a problem with it and it will be an on going problem. They need to redesign the door switch and give us all some relief. Not make us pay for extended warranties. That doesnt make sense. Why should consumers purchase high end appliances and pay to keep them running? Does the extended warranty cover all the days I have no dishwasher when I am afraid to have a dinner party because it could fail again and cause me more inconvenience?
Published: July 30, 2013
Arlene of Mentor, OH
Source: consumeraffairs.com

In mid February I wrote a complaint about all the problems I had with my #
In mid February I wrote a complaint about all the problems I had with my # kfis29 French door fridge. I contacted whirlpool who makes the unit and told them that when I call kitchen aid they wouldn`t do nothing for me! After a week the place that sold the unit to me who had nothing to do with the problem also called whirlpool and told them the story. Guess what? He told me to come in and pick out a new fridge of equal value and that whirlpool corp. was giving me a full refund. So the store rep, told me that he had very little problems with GE and that if he did GE backed him 100% so I bought a GE French door, super quiet and they also threw in a 5-year extended warranty! PS DON`T GIVE UP! KEEP CALLING UNTIL THEY SATISFY YOU. WE PAID A LOT OF MONEY FOR THESE AND JUST WANT WHAT WE PAY FOR! THE STORE I USED WAS RICHMOND APPLIANCE, STATEN ISLAND NEW YORK! THEY’RE THE BEST FAMILY BUSINESS around.
Published: January 1, 1970
steve of Staten Island, NY
Source: consumeraffairs.com

Purchased Stainless Steel Kitchenaid (Whirlpool Corp) dishwasher 2015-07-29
Purchased Stainless Steel Kitchenaid (Whirlpool Corp) dishwasher 2015-07-29 at the Brick. Total cost including extended 5 yr Trans Global Warranty, delivery and taxes $1350.34. Starting in early 2020 the Dishwasher intermittently stopped dissolving soap which would fall to the bottom of the tub undissolved and stopped drying the dishes which we ignored until May 2020. Called Trans Global many times to solve this problem. They made 3 repairs that included 6 visits from their repair man because he comes with no repair parts and orders them after each visit. He made adjustments and even said he changed the control circuit board. Which did not solve the problem.I finally took a whole Saturday in Jan 2021 and figured out how to read the cryptic service sheet provided with the machine and got the control board to give me the error code readout (with help from Google). Error code 8-2 (8 LED flashes followed by 2 LED flashes) ....check wash pump! Sure enough the bushings that hold the water pump shaft are worn down causing the wash pump to draw high current and stall periodically. Simply put, bad material choice for the bushings by the designers! (Also the rubber tubing & seals and plastic parts of the dish racks are breaking down - also bad material choices). Or was this stainless steel dishwasher designed to fail at 5 years? So the cost in Canadian dollars from Whirlpool Corp. for the repair parts (as the unit is now out of extended warranty) is: 1. W10529163 Wash Pump - Motor $291.77 2. W10445975 Rubber Elbow and 2 Clamps 92.653. W10538166 Rubber Sealing Grommet 33.73Total cost (shipping not included) $418.15 You would think that if the designers made errors they would supply these parts at cost... maybe $75.00??? Basically the cost of repairing this machine is not a good investment as a new one can be purchased for $600. Right now we call this unit our $1350 towel rack! I recommend that people do not support Whirlpool Corp or any other brands associated with them with repeat purchases, I will not.I also wonder if Trans Global Warranty Corp. is complicit in not replacing the pump under warranty because they are well aware of the exorbitant cost of these parts. The sad thing is that this stainless dishwasher that should have lasted at least another 7 or 8 years will end up in the dump. Also I will need several trips to an appliance store to buy a new unit shipped all the way from Korea or Germany.
Published: January 10, 2021
Ron of Waterdown, ON
Source: consumeraffairs.com

Visa MasterCard

Site Secured By The Website Guardian
TOP