Appliance Types


Appliance Brands


Article Categories


More Articles


Beko Appliances
Beko Appliances

Beko Appliance Error Codes

Established in 1955 and sold in over 140 countries, Beko is recognized as the number one home appliance brand in the European market. Beko is proud to enrich the lives of consumers who are conscious about wellness, their family's health, and nutrition by providing energy-efficient appliances.


Dishwasher Error Codes

CODE: No lights lit 
PROBLEM: No power, or no fault detected. 
FIX: Check dishwasher is switched on. Check mains power. 

CODE: First light lit 
PROBLEM: Dishwasher not filling sufficiently before timeout. 
FIX: Why is My Dishwasher Not Filling With Water? 

CODE: Second light lit 
PROBLEM: Inlet valve or water sensor error. 
FIX: Check inlet valve. 

CODE: Third light lit 
PROBLEM: Water temperature sensor error. 
FIX: Check/replace water temperature sensor (NTC). Pouring boiling water into the sump may fix the issue temporarily. 

CODE: First and second lights lit 
PROBLEM: Heating element fault.


Dryer Error Codes

CODE: Er 01  
PROBLEM: The tumble dryer door has been opened while the machine is running 
FIX: Close the door. Do not open the door until the program is completed 

CODE: Er 02  
PROBLEM: Overflow switch error 
FIX: Check for water leakage. Check the overflow switch operation. Check wiring to overflow switch 

CODE: Er 03  
PROBLEM: Not used, idle 
FIX: Not used 

CODE: Er 04  
PROBLEM: Door temperature sensor (NTC) has exceeded 60ËšC 
FIX: The door sensor has exceeded a safe temperature, the compressor will stop for five minutes. Restart program after cool down. The front thermistor is defective or the control is recieving a false reading. Check wiring to thermistor. Replace the thermistor 

CODE: Er 05  
PROBLEM: Start/Pause/Cancel button pressed during program 
FIX: Restart program 

CODE: Er 06  
PROBLEM: Compressor temperature sensor (NTC) has exceeded safe limits 
FIX: The compressor sensor has exceeded a safe temperature, the compressor will stop for four minutes. Restart program after cool down. The compressor thermistor is defective or the control is receiving a false reading. Check wiring to thermistor. Replace the thermistor 

CODE: Er 07  
PROBLEM: Not used, idle 
FIX: Not used 

CODE: Er 08  
PROBLEM: Drying program has exceeded the maximum permitted time 
FIX: For cotton and synthetic programs the limit is 300 minutes. Restart the cycle after cool down and test again 

CODE: Er 09  
PROBLEM: Mains supply voltage too low, less than 165 Volts 
FIX: Correct mains supply voltage 

CODE: Er 10  
PROBLEM: Mains supply voltage too high, greater than 265 Volts 
FIX: Correct mains supply voltage 

CODE: Er 11  
PROBLEM: Compressor temperature sensor (NTC) has exceeded maximum permitted operation limits 
FIX: The compressor NTC can only operate with up to 40 instances of being over the maximum permitted temperature in a single program, if this limit is exceeded then this error code will be displayed anda cool down phase initiated.  Restart program after cool down . The compressor thermistor is defective or the control is receiving a false reading. Check wiring to thermistor. Replace the thermistor 

CODE: Er 12  
PROBLEM: Rotary error 
FIX: Check operation rotary control 

CODE: Er 13  
PROBLEM: Not used, idle 
FIX: Not used 

CODE: Er 14  
PROBLEM: Humidity Sensor has exceeded the maximum permitted time 
FIX: For cotton and synthetic programs the limit is 300 minutes. Restart the cycle after cool down and test again 

CODE: Er 15  
PROBLEM: Drum idle at the start of sensor drying programs 
FIX: Check operation of the drum. Check motor operation. Check drive belt 

CODE: Er 16  
PROBLEM: Door NTC or thermistor open circuit and the tumble dryer will halt 
FIX: The front door thermistor is defective or the control is not in contact with it. Check wiring. Replace the thermistor 

CODE: Er 17  
PROBLEM: Compressor NTC or thermistor open circuit and the tumble dryer will halt, program aborted 
FIX: The compressor thermistor is defective or the control is not in contact with it. Check wiring. Replace the thermistor 

CODE: Er 18  
PROBLEM: Door NTC or thermistor short circuit and the tumble dryer will halt 
FIX: The front door thermistor is defective or the control is not in contact with it. Check wiring. Replace the thermistor 

CODE: Er 19  
PROBLEM: Compressor NTC or thermistor short circuit and the tumble dryer will halt, program aborted 
FIX: The compressor thermistor is defective or the control is not in contact with it. Check wiring. Replace the thermistor 

CODE: Er 20  
PROBLEM: Rotary control turned while the dryer is in operation 
FIX: Restart program


Range Error Codes

No Error Codes For This Product At This Time.

Oven emits steam when in use 
- It is normal that steam escapes during operation. >>> This is not a fault. 

Product emits metal noises while heating and cooling. 
- When the metal parts are heated, they may expand and cause noise. >>> This is not a fault. 

Product does not operate. 
- The mains fuse is defective or has tripped. >>> Check fuses in the fuse box. If necessary, replace or reset them. 
- Product is not plugged into the (grounded) socket. >>> Check the plug connection. 

Oven light does not work. 
- Oven lamp is defective. >>> Replace oven lamp. 
- Power is cut. >>> Check if there is power. Check the fuses in the fuse box. If necessary, replace or reset the fuses. 

Oven does not heat. 
- Function and/or Temperature are not set. >>> Set the function and the temperature with the Function and/or Temperature knob/key. 
- In models equipped with a timer, the timer is not adjusted. >>> Adjust the time. (In products with microwave oven, timer contols only microwave oven.) 
- Power is cut. >>> Check if there is power. Check the fuses in the fuse box. If necessary, replace or reset the fuses. 

(In models with timer) Clock display is blinking or clock symbol is on.  
- A previous power outage has occured. >>> Adjust the time / Switch of the product and switch it on again.

What do I do if my Beko electric oven has stopped working? 
Ensure that the appliance has not been switched off at the mains power switch. Check to see if the fuse has been tripped or blown. If the clock on your oven is flashing, it must be reset before the oven can be used again. Please refer to the instruction manual for specific advice on how to do this. 

How do I replace the light in my Beko oven? 
Make sure the product is disconnected from the mains and has cooled down beforehand. Turn the glass cover counter-clockwise to remove it, wearing a rubber glove gives a better grip. Then unscrew the bulb and replace it. Reattach the glass cover. If in doubt, consult your product manual which will have instructions under: 'Replacing the Oven Lamp'. 

My oven timer shows "AUTO" or "A" in the display. 
This indicates that the oven has been set to automatically turn on and off at a specified time. You will need to reset it if you want to use the oven in manual mode. Take a look at the specific instructions in the user manual for your oven to find out how to do this. 

What is a fan oven? 
A fan assisted oven has a fan designed to circulate air around the oven. The fan distributes heat evenly around the oven to cook food more evenly, often in less time and at a lower temperature, giving you better results and the opportunity to batch cook. 

Why does the manual state to heat the appliance for 30 minutes before initial use? 
The purpose of heating the appliance 30 minutes before initial use, is to ensure that any production residues or layers will be burnt off and removed. 

How do I clean the inside of my Beko oven? 
If the inside of your oven has an enamelled interior, the most effective cleaning method is a damp cloth while the oven is still warm. Also, oven cleaning agents suitable for enamel can also be used if required. If your oven has catalytic liners, they should not be cleaned. To remove any built-up deposits simply remove all oven trays and set the temperature to 240°C for one hour. If you aren't sure what type of interior your oven has, please refer to your instruction manual. 

How does a self-cleaning oven work? 
A self-cleaning oven deep cleans itself at the touch of a button. Beko’s self-cleaning ovens are equipped with a pioneering in-built Pyrolytic self-cleaning feature which amplifies its internal temperature to 480°C! The oven is self-locking throughout the process and once it reaches maximum temperature, all grease, stains, marks, and burns are turned to dust – just wipe them away with a damp cloth. This Beko oven gives you the option of two self-cleaning programmes; one for heavily soiled interiors (runs for 120 minutes), and an Eco cycle (runs for 90 minutes) – which can save up to 25% in energy as well as effort. Our ovens also come with official recommendation from the Energy Saving Trust so not only will you be saving time and energy, you will be saving money as well. 

Overheating Issues 
If your Beko oven is always overheating, we can help! There could be a number of parts that could be causing this issue, but don't worry as we offer a range of replacements. 
A faulty Thermostat 
Your thermostat is responsible for regulating the heat inside your oven; but obviously, if this part is not functioning properly, then the heat inside your oven will not be regulated properly, causing it to over or under cook your meals. This can be a major issue, as you'll have to constantly check your meals whilst it's cooking to see when it is accurately cooked. Thankfully, we sell a selection of affordable oven thermostats that will rectify this issue, and will ensure your appliance is cooking your meals accurately once again. 
A faulty cooling fan 
Another part that could be related to your overheating issue, is your cooling fan. The role of this part is pretty self explanatory - it cools your oven cavity to prevent it from over heating. If this part stops working, then trying to keep your oven cavity cool will be a major issue! If your cooling fan has become faulty, you can purchase a replacement 

Prolonged Cooking Times 
Everyone wants their meals cooked instantly, so when your cooker is taking longer than usual to cook your meals, it can become really frustrating. Again, there could are a few parts related to this issue, but thankfully we have the replacements to resolve this issue. 
Underperforming oven element 
Your oven element is the cooker part that heats up and distributes the heat that allows you to cook your meals. And therefore, if it begins to start to become faulty and work insufficiently, you will notice that your cooker performance will diminish, and that cooking times would have increased. If your oven element is no longer performing as good as it used to, purchase a replacement today! 
Oven seal detaching 
Your oven seal is a strip of rubber that is attached to the trim of your oven door which protects the edge of your oven door as well helping your oven to retain the heat inside the cavity. If the seal begins to come away from your oven door, heat will be allowed to escape, resulting in your oven taking longer to heat up and cook your meals. To ensure your oven is retaining heat again, purchase a replacement from our range of oven door seals. 

Oven no longer igniting 
If your oven burner is having trouble igniting or the electrode is no longer sparking, your oven won't produce any heat which will result in your oven being unable to cook your meals. However, this problem can easily be resolved by purchasing one of our replacements. 
To view our entire range of Beko oven parts, please click here. If you are having any further problems with your Beko oven please do not hesitate to contact our customer service team - they' be more than happy to assist you to ensure your oven is fully functioning again.


Refrigerator Error Codes

CODE: E0  
PROBLEM: Freezer sensor failure 

CODE: E1  
PROBLEM: Freezer defrost sensor failure 

CODE: E3  
PROBLEM: Fridge sensor failure 

CODE: E4  
PROBLEM: Defrost heater failure 

CODE: E8  
PROBLEM: Ice sensor failure 

CODE: E9  
PROBLEM: Ice machine failure 

CODE: 
PROBLEM: Cooling fault. Refrigerant leakage, compressor malfunction, fan failure in the refrigerator, improper sensor operation, open long door time. 

CODE: 
PROBLEM: Heater fault. The heaters do not work or do not work at full capacity, the refrigerator sensor must be repaired. 

CODE: 
PROBLEM: The sensor circuit is open. One of the sensors is not installed in place, a defect in the wires, a bad contact on the connectors. 

CODE: 
PROBLEM: Sensor short-circuit. Malfunction of the sensor, defect of the wires connecting one of the 3 temperature sensors with the control board, poor contact in the connectors. 

CODE: 
PROBLEM: The button is pressed. Faulty buttons, dirty buttons. 

CODE: 
PROBLEM: Malfunction of the compressor. Compressor does not work, refrigerant leaks, blockage of the circulation system.


Washer Error Codes

CODE: E1 
PROBLEM: The is error code means there’s been an NTC error detected in the washing machine. This means there’s an issue with the thermistor wiring in the machine, you can check the thermistor to test the connection on Beko washing machines it should read 4700 ohms with a temperature of 25ËšC. 

CODE: E2 
PROBLEM: This error code means there is a problem with the heater, again this will most likely be a wiring issue and with the assistance of the instructions manual you might be able to correct it. However, I would advise calling in a professional. 

CODE: E3 
PROBLEM: This error code is again related to the heater in the washing machine, however, this means there is a constant stream of heat. You need to examine the control board relay for the heater but again this is something that should only be done by a professional. 

CODE: E4 
PROBLEM: This error code encompasses a few different potential problems, but they are all related to the fact that your washing machine won’t fill up with water. In some cases, this could be an easy issue to fix it may simply be an issue with the door causing a jam or it could be a more complex issue with the water valve or the wiring. 

CODE: E5 
PROBLEM: This error code means there is a drainage issue with the washing machine again this could be caused by a variety of issues from simple blocks in the pump filter, to more complex problems with the control board. So, if you’re unsure of how to proceed call in a professional to assist you. 

CODE: E6 
PROBLEM: This error code means there is a problem with the motor, you will probably notice the washing machine jumping of shaking during a wash cycle. Again, this could be caused by numerous issues but unlike some other error codes, this is something best left to a professional to fix. 

CODE: E7 
PROBLEM: This code means an issue with the level sensor has been detected, one common warning sign is the fact that the washing machine empties every time you try to start it up. Or in some cases it may not start a cycle at all, a technician will be needed to examine the sensor to diagnose the problem. 

CODE: E8 
PROBLEM: The codes covers a variety of issues but will usually be related to your washing machine not filling with water. Because this code encompasses an array of potential problems it requires numerous checks to diagnose, so it’s something that only a professional should carry out. 

CODE: E9 
PROBLEM: The E9 error code means there is a problem with the washing machine’s door lock. If you’re lucky it might be relatively simple to fix if it’s just a simple issue with the door however it could easily be a more complex task as well. So, if you’re unsure of what to do or can’t identify the problem call in a professional. 

CODE: E10 
PROBLEM: The code is again related to the door but this time it means the washing machine is detecting that the door is jammed in some way. This could again be an internal issue though, so it might not be simple to fix. 

CODE: E11 
PROBLEM: This code means the washing machine as detected a problem with the motor, due to its complexity this is something a technician will need to examine for you. 

CODE: E17 
PROBLEM: This code means there’s been an excessive amount of foam detected in the washing machine, thankfully this is a problem you can usually fix on your own by clearing the foam and running some rinse cycles to clear everything. This can happen due to poor-quality detergent or simply overloading your washing machine with too much during a wash cycle. 

CODE: E18 
PROBLEM: This final error code means an unbalanced washing load has been detected during a cycle, if your washing machine doesn’t spin then this can also cause the E18 error. Thankfully simply stopping the cycle, reloading and then restarting it should solve the issue.



Beko Appliance Error Codes

Beko appliance fault codes

Beko appliance diagnostic codes

Beko appliance error symbols

Beko appliance common faults


Product Reviews:

Surprise surprise it actually dries clothes! My previous fairly expensive d
Surprise surprise it actually dries clothes! My previous fairly expensive drier always left clothes a bit damp. This one is easy to use, loads of different settings, there is a light inside and has a child lock. Would definitely recommend!
Published: August 6, 2020
Claire F
Source: ao.com

Nice product. Works soo much better than the dishwasher it displaced. Littl
Nice product. Works soo much better than the dishwasher it displaced. Little like a Tardis. Same footprint as previous machine.
Published: September 8, 2020
Martin Doe
Source: ao.com

I am the proud owner of a new Beko Condenser tumble dryer, and I could not
I am the proud owner of a new Beko Condenser tumble dryer, and I could not be happier with my choice. Like Mary Poppins it is `Practically perfect in every way`.
Published: August 18, 2020
Marianne
Source: ao.com

I am a landlord with multiple properties. I currently have 4 beko washer/dr
I am a landlord with multiple properties. I currently have 4 beko washer/dryers and 3 beko fridges. The earliest one was purchased 7 years ago. Not one of these appliances has given any problems. Compared to hotpoint products, these white goods seem to be perfect.
Published: July 22, 2018
AKA
Source: trustpilot.com

Very happy with the wash cycles But! A packaging block under machine was no
Very happy with the wash cycles But! A packaging block under machine was not clearly visible and identification ribbon was not visible at all resulting in a call out service charge to us!!! Something BEKO needs rectify, a sorry we will pass onto our packaging dept is not good enough!!
Published: March 17, 2018
Linda S
Source: productreview.com.au

This dishwasher is fantastic, after moving into our new house and our old o
This dishwasher is fantastic, after moving into our new house and our old one flooding the new kitchen we needed one with high spec but within budget yet was able to get her quickly. This one is perfect for a family of 3 & room for entertaining too. The delivery crew were amazing too, they called to keep me up to date with when they would be here.
Published: September 5, 2020
Emily Brown
Source: ao.com

We have for about three years a beco washing machine and a dishwasher and a
We have for about three years a beco washing machine and a dishwasher and a condenser tumble dryer these are the best machines we have ever bought highly recommend these machines. We have had all sorts of makes but these machines are truly the best we have ever had I know it sounds to good to be true but they are think I might try a fridge next
Published: January 15, 2020
Steve Jackson
Source: trustpilot.com

This machine is great. Very quiet and very quick at drying everything. I di
This machine is great. Very quiet and very quick at drying everything. I didn't realise how bad/old our previous dryer had got till we used the new one. The sensor works very well.
Published: August 1, 2020
Matt
Source: ao.com

Ability to switch the "joker" area between fridge, for when you r
Ability to switch the "joker" area between fridge, for when you require extra cool space, and freezer, in case you need to expand your frozen food capacity.
Published: January 15, 2020
ROBERT
Source: bekoappliances.com

I wash everything in this washing machine from bedding, towels, dedicates,
I wash everything in this washing machine from bedding, towels, dedicates, cottons and synthetics. It gets used nearly every day and time and time again I have been happy with the way the clothes have been washed. I also love the timer and use that when I go out for a few hours and by the time I get home the washing has finished, ready for me to hang it one the line. I highly recommend this washing machine.
Published: February 17, 2018
Isaby Southport
Source: productreview.com.au

Saw a a concern as to not knowing the temperature of oven when on.... when
Saw a a concern as to not knowing the temperature of oven when on.... when the red light stops blinking you are at the dialed temperature.... Cheaper ovens you rely on a digital reading which is often wrong. Cranks up the heat
Published: January 15, 2020
Chef Boy Ar Dee EI, NY
Source: bekoappliances.com

Excellent Dishwasher, cheap as chips and surprisingly quite with plenty of
Excellent Dishwasher, cheap as chips and surprisingly quite with plenty of washing settings to choose from i had it up and running in minutes, top tip remember to buy salt LOL
Published: September 8, 2020
David O
Source: ao.com

I purchased this unit 4 months ago to replace my blue star range. Very happ
I purchased this unit 4 months ago to replace my blue star range. Very happy we went with Beko. Nice features such as LED control knobs which makes it easy to know when the cooktop is on. Oven heats up quickly and has constant temperature front to back. My only change would be a smooth griddle a accessory for the center burner.
Published: May 15, 2020
Pipet
Source: bekoappliances.com

I bought this machine almost a year ago to replace a Samsung front loader w
I bought this machine almost a year ago to replace a Samsung front loader which I'd used for over 5 years with no problems. I got an excellent deal from Appliances on Line $538 and free delivery. I like the extra fast spin speed 1400rpm and other features that weren't available on the Samsung, it is also much quieter than previous machines. If I could find a fault I would like a warning beep when it finishes washing and also when it starts, otherwise I can recommend it.
Published: November 17, 2017
Dajovic Melbourne
Source: productreview.com.au

I absolutely live my new range. It’s efficient and state of the art. Itâ€
I absolutely live my new range. It’s efficient and state of the art. It’s also easy to clean. The cooking is even and I’m just getting use to it’s high efficiency. I strongly recommend this appliance as I am very picky.
Published: August 15, 2018
Stem47 Madison New Jersey
Source: bekoappliances.com

Good value for money appliance - easy to use, no nonsense product ????
Good value for money appliance - easy to use, no nonsense product ????
Published: September 6, 2020
Mum of five children ??
Source: ao.com

Excellent customer service. Item well priced and works great. Just as descr
Excellent customer service. Item well priced and works great. Just as described Easy to use.
Published: September 7, 2020
Pen
Source: ao.com

After looking around for a condenser tumble dryer, went for this one, and I
After looking around for a condenser tumble dryer, went for this one, and I am glad I did. It’s simple, pretty quite and does it’s job. Recommend it to everyone.
Published: August 6, 2020
Richard
Source: ao.com

From gentle to outdoor winters muck , all loads handled well . Easy to ope
From gentle to outdoor winters muck , all loads handled well . Easy to operate and the price was very competitive . Attractive design , not bulky . I’d recommend this machine for singles or families , small or large loads. No problems handling pet hair . Not noisy.
Published: March 17, 2015
Shells Metropolitan Adelaide, SA
Source: productreview.com.au

Had my my fridge freezer nearly 5 years, not one single problem with it. Ne
Had my my fridge freezer nearly 5 years, not one single problem with it. Never needed even a draw for it!!
Published: May 17, 2018
Kayley guffogg
Source: trustpilot.com

Love this washing machine! Have only one small complaint when you have to p
Love this washing machine! Have only one small complaint when you have to push the START/PAUSE button, I have to push really hard to get machine to kick into gear and start. I have to use my thumb and really press hard for it to make sure that it starts. That is my only complaint. The machine has a lot of options for washing cycles which are great. I wash a range of clothing from sheets and other bedding to woolen winter long sleeve tee's and never have a problem as there are good settings to choose if you want a long or a short cycle. Delicate clothes are just fine in this washing machine. Only use half the amount of washing powder you normally use as this machine washes well.
Published: August 17, 2018
Sunshine Gippsland, VIC
Source: productreview.com.au

Very pleased with this product it’s a lovely dryer made up with it
Very pleased with this product it’s a lovely dryer made up with it
Published: August 17, 2020
Katie
Source: ao.com

Had this delivered about 1 month ago. The burners all worked well. Lot'
Had this delivered about 1 month ago. The burners all worked well. Lot's of BTU's which is important for me. However the oven door would not close properly. After a couple weeks of frustration, a BEKO certified tech came out and showed us that you just turn the oven to 'self clean' and the latch will move so that the oven door will close properly. Simple - but why not have that stated in the manual? Other than that the oven works very well. Temp seems accurate. Powerful too. It looks great and am happy with the purchase. Would recommend.
Published: August 15, 2020
JDJD from Minnesota USA
Source: bekoappliances.com

Love, love, love my new range! I love the pure simplicity and power to prod
Love, love, love my new range! I love the pure simplicity and power to produce wonderful meals. I love the accuracy of oven temperature and variety of choices. So simple to use! Visually completes my new kitchen.
Published: January 15, 2018
AlaskanFoodie Wasilla Alaska
Source: bekoappliances.com

Beko is the best appliances i ever used. They can't be compared to the
Beko is the best appliances i ever used. They can't be compared to the local company. I love Beko fridge freezer. Thank you Currys.
Published: December 1, 2018
Maryum Malik
Source: trustpilot.com

Visa MasterCard

Site Secured By The Website Guardian
TOP