Maytag Dryer stopped spinning.

Drive Belt.
The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley. Over time, the belt can break from normal use. If the belt is broken, the dryer won’t turn. To quickly determine if the belt is broken, reach into the dryer and turn the drum by hand. If the drum spins very easily, the belt is likely broken. Next, inspect the belt to confirm that it is broken. If the belt is broken, replace it.

Drum Roller.
One or more of the drum rollers might be worn out. Most dryers have two drum support rollers on the rear of the drum, and some dryers have two more rollers supporting the front of the drum. The rollers must spin freely to work properly. If the rollers don’t spin freely, the motor will get overloaded and the dryer will stop. If the drum rollers are worn out, the rollers may not spin freely. To determine if the support rollers are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not rotate freely, check the support rollers for wear. If one or more of the rollers don’t turn freely, we recommend replacing all of the rollers at the same time as a preventative measure. (The roller shaft can often be reused if it is in good condition. Clean the shaft thoroughly before installing the new rollers.)

Drum Support Roller & Axle.
One or more of the drum roller axles might be worn out. Most dryers have two drum support rollers on the rear of the drum, and some dryers have two more rollers supporting the front of the drum. The rollers must spin freely to work properly. If the drum roller axles are worn out, the rollers may not spin freely, causing the motor to overload and the dryer to stop. To determine if the drum roller axles are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not rotate freely, check the axles for wear. If the rollers spin freely without wobbling, the axles do not need to be replaced. If the roller wobbles and/or does not spin freely, we recommend replacing all of the axles and rollers as a preventative measure.

Drum Slide, Glide, or Pad.
If the dryer stops turning during the cycle, one or more of the drum glides (also called slides) might be worn out. The drum glides are small plastic pieces that support the front of the dryer drum. As the drum rotates, it slides on these plastic pieces. Over time, the drum glides wear out. If the drum glides are worn out, the drum can start binding and puts strain on the motor. If this happens, the motor shuts down, preventing the dryer from turning. To determine if the drum glides are worn out, inspect them for wear. If the glides are worn out, replace all of the glides as a set.

Drum Bearing.
The drum bearing supports the rear of the dryer drum. Over time, this bearing wears out. If the drum bearing is worn out, it might put too much strain on the motor, causing the dryer to stop mid-cycle. To determine if the drum bearing is at fault, remove the dryer belt and try turning the drum by hand. If the drum rotates freely, it is unlikely that the drum bearing is worn out. If the drum makes squealing or grinding sounds when turned and/or is hard to turn, check the drum bearing and replace it if necessary.

Drum Roller Axle.
One or more of the drum roller axles might be worn out. Most dryers have two drum support rollers on the rear of the drum, and some dryers have two more rollers supporting the front of the drum. The rollers must spin freely to work properly. If the roller axles are worn out, the rollers may not spin freely, causing the motor to overload and the dryer to stop. To determine if the drum roller axles are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not rotate freely, check the support rollers for wear. If the rollers spin freely without wobbling, the axles do not need to be replaced. If the roller wobbles and/or does not spin freely, we recommend replacing all of the axles and rollers as a preventative measure.

Maytag Dryer stopped spinning.

Drive Belt.
The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley. Over time, the belt can break from normal use. If the belt is broken, the dryer won’t turn. To quickly determine if the belt is broken, reach into the dryer and turn the drum by hand. If the drum spins very easily, the belt is likely broken. Next, inspect the belt to confirm that it is broken. If the belt is broken, replace it.

Drum Roller.
One or more of the drum rollers might be worn out. Most dryers have two drum support rollers on the rear of the drum, and some dryers have two more rollers supporting the front of the drum. The rollers must spin freely to work properly. If the rollers don’t spin freely, the motor will get overloaded and the dryer will stop. If the drum rollers are worn out, the rollers may not spin freely. To determine if the support rollers are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not rotate freely, check the support rollers for wear. If one or more of the rollers don’t turn freely, we recommend replacing all of the rollers at the same time as a preventative measure. (The roller shaft can often be reused if it is in good condition. Clean the shaft thoroughly before installing the new rollers.)

Drum Support Roller & Axle.
One or more of the drum roller axles might be worn out. Most dryers have two drum support rollers on the rear of the drum, and some dryers have two more rollers supporting the front of the drum. The rollers must spin freely to work properly. If the drum roller axles are worn out, the rollers may not spin freely, causing the motor to overload and the dryer to stop. To determine if the drum roller axles are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not rotate freely, check the axles for wear. If the rollers spin freely without wobbling, the axles do not need to be replaced. If the roller wobbles and/or does not spin freely, we recommend replacing all of the axles and rollers as a preventative measure.

Drum Slide, Glide, or Pad.
If the dryer stops turning during the cycle, one or more of the drum glides (also called slides) might be worn out. The drum glides are small plastic pieces that support the front of the dryer drum. As the drum rotates, it slides on these plastic pieces. Over time, the drum glides wear out. If the drum glides are worn out, the drum can start binding and puts strain on the motor. If this happens, the motor shuts down, preventing the dryer from turning. To determine if the drum glides are worn out, inspect them for wear. If the glides are worn out, replace all of the glides as a set.

Drum Bearing.
The drum bearing supports the rear of the dryer drum. Over time, this bearing wears out. If the drum bearing is worn out, it might put too much strain on the motor, causing the dryer to stop mid-cycle. To determine if the drum bearing is at fault, remove the dryer belt and try turning the drum by hand. If the drum rotates freely, it is unlikely that the drum bearing is worn out. If the drum makes squealing or grinding sounds when turned and/or is hard to turn, check the drum bearing and replace it if necessary.

Drum Roller Axle.
One or more of the drum roller axles might be worn out. Most dryers have two drum support rollers on the rear of the drum, and some dryers have two more rollers supporting the front of the drum. The rollers must spin freely to work properly. If the roller axles are worn out, the rollers may not spin freely, causing the motor to overload and the dryer to stop. To determine if the drum roller axles are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not rotate freely, check the support rollers for wear. If the rollers spin freely without wobbling, the axles do not need to be replaced. If the roller wobbles and/or does not spin freely, we recommend replacing all of the axles and rollers as a preventative measure.