At Monogram it's not just one detail, it's many. When you put them all together, you create appliances that look, feel and perform as if they were designed perfectly for you.

Dishwasher Repair

For the home, kitchen and beyond, Monogram manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of Monogram appliance repair from experienced professionals, your local Appliance Helper can help.

Monogram Dishwasher not cleaning 
The water inlet valve opens to allow water to enter the dishwasher. If the valve is clogged or defective, the dishwasher won’t get enough water to clean dishes properly. If the water inlet valve is clogged, replace it. Do not attempt to clean the water inlet valve—cleaning the valve could make it more likely to fail. 

Monogram Dishwasher not draining 
The drain impeller pushes water through the drain hose and into the garbage disposer or drain line. If the impeller is broken, replace it. 

Monogram Dishwasher buttons not working 
First, confirm that the dishwasher display is working. If the display is still working, try pressing some of the touchpad buttons. If some of the buttons respond correctly but others don’t, it is likely that the touchpad is at fault. (Some manufacturers sell the touchpad separately from the control panel. Other manufacturers require that you purchase the touchpad and control panel together. If you cannot replace the touchpad individually, replace the touchpad and control panel.) 

Monogram Dishwasher lights flashing or blinking 
The heating element heats up the water to operating temperature. If the water doesn’t reach the proper temperature after a set amount of time, a light on the control panel might start flashing. To determine if the heating element has burned out, use a multimeter to test it for continuity. If the heating element does not have continuity, replace it. 

Monogram Dishwasher leaking 
The water inlet valve opens to allow water to enter the dishwasher. If the water inlet valve is stuck open, the dishwasher will continue to fill with water until the dishwasher leaks or overflows. If the water inlet valve is at fault, replace it. Water inlet valves are not repairable—if the valve is defective, you must replace it. 

Monogram Dishwasher leaking from motor area 
First, try to determine the source of the leak. If the water is leaking from the motor shaft area, the motor shaft seal is likely defective. If the seal is defective, replace it. (Some manufacturers sell the seal independently of the impeller. Other manufacturers require that you purchase the impeller and seal together. Still other manufacturers require that you purchase the entire pump and motor assembly instead of the impeller and seal. It is usually more cost effective to replace the impeller and seal kit rather than the pump and motor assembly.) 

Monogram Dishwasher won't start 
The door switch prevents the dishwasher from running while the door is open. If the door switch is defective, the switch will prevent the dishwasher from running even when the door is closed. To determine if the door switch is at fault, use a multimeter to test the switch for continuity. If the switch does not have continuity, replace it. 

Monogram Dishwasher won't latch 
If the door hinges are damaged, the door won’t be able to latch properly. Inspect the door hinges for damage. If a hinge is bent or broken, replace it. 

Monogram Dishwasher dispenser not dispensing soap 
The bi-metal actuator is a metal loop which acts as a latch for the dispenser door. As electricity is applied to the bi-metal, it deforms and bends away from the latch, releasing it. If the bi-metal is burned out, it won’t release the dispenser door. To determine if the bi-metal has burned out, use a multimeter to test it for continuity. If the bi-metal does not have continuity, replace it. In addition, make sure that the dishwasher is getting enough water. If the water level is too low, the wash motor may not draw enough current through the bimetal, causing the bimetal not to bend enough to work properly. 

Microwave Repair

For the home, kitchen and beyond, Monogram manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of Monogram appliance repair from experienced professionals, your local Appliance Helper can help.

Monogram Microwave not heating 
The diode converts the A/C power output of the transformer to D/C, doubling the voltage to nearly 5,000 volts. This high voltage powers the magnetron to heat the food. If the diode burns out, the magnetron won’t receive enough voltage to operate, preventing the microwave from heating. When the diode fails, it is often visibly burned out. Inspect the diode and if the diode is burned out, replace it. If inspecting the diode proves inconclusive, test it with a multimeter that uses a 9-volt battery or put a 9-volt battery in series with the diode. When the leads are reversed, the diode should only have continuity in one direction. (Warning: The microwave oven can store a lethal amount of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the high running voltage and the potential for electric shock, it is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the diode.) 

Monogram Microwave not working 
If too much current passes through the microwave circuitry, the line fuse will blow. If the line fuse blows, the microwave won’t start. To determine if the line fuse is at fault, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it. In addition, you should investigate and resolve the problem that caused the fuse to blow. If you don’t resolve the underlying issue, the new fuse will blow too. (Caution: The microwave oven can store thousands of volts of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the potential for electric shock, it is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the line fuse.) 

Monogram Microwave light bulb not working 
The light bulb itself might be burned out. Replace the light bulb before replacing any of the parts associated with the light bulb 

Monogram Microwave shuts off after a few seconds 
A door switch might be failing intermittently. Check each of the door switches for signs of overheating, arcing, or burning. If you don’t see any obvious signs of failure, use a multimeter to test each switch for continuity. If any of the switches is visibly damaged or only has intermittent continuity, replace it. 

Monogram Microwave turntable not turning 
Use a multimeter to test the motor for continuity. If the turntable motor does not have continuity, replace it. 

Monogram Microwave buttons not working 
To determine if the touchpad is defective, try pressing each of the buttons on the control panel. If some of the buttons respond correctly while others don’t, replace the touchpad. 

Monogram Microwave display not working 
If the display goes out partially, the display board is more commonly at fault. If the display isn’t working at all, either the main control board or the display board could be at fault. 

Monogram Microwave turns on by itself 
First, make sure that the touchpad is working properly. If the touchpad is working properly, the main control board is likely at fault. If the control board is defective, replace it. 

Monogram Microwave is sparking or arcing 
The waveguide cover might be damaged and shorting out. Try removing the waveguide cover and see if the problem resolves. If the waveguide cover is burnt or will not stay in place, replace it.

Range Repair

For the home, kitchen and beyond, Monogram manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of Monogram appliance repair from experienced professionals, your local Appliance Helper can help.

Monogram Oven not heating 
The igniter is the most commonly defective part for an oven not heating. The igniter has two main functions. First, the igniter draws electrical current through the oven safety valve to open it. Second, the igniter gets hot enough to glow and ignite the gas in the oven burner. If the igniter gets weak, it will fail to open the safety valve correctly. If the valve does not open, the oven will not heat. To determine if the igniter is defective, observe the igniter when the oven is on. If the igniter glows for more than 90 seconds without igniting the gas flame, this indicates that the igniter is too weak to open the valve. If the igniter is weak, replace it. If the igniter does not glow at all, use a multimeter to test the igniter for continuity. If the igniter does not have continuity, replace it. 

Monogram Oven doesn't bake evenly 
If the bake element is burned out, the oven will only be heated by the broil element. This will cause the oven to heat unevenly. When the bake element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element is not heating. Often, if the element has burned out, it will be visibly damaged. Inspect the bake element for holes or blisters. To determine if the bake element has burned out, use a multimeter to test the element for continuity. If the bake element does not have continuity, replace it. 

Monogram Oven broiler not working 
The broiler element may have burned out. When the broil element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element is not heating. Often, if the element has burned out, it will be visibly damaged. Inspect the broil element for holes or blisters. To determine if the broil element has burned out, use a multimeter to test the element for continuity. If the broil element does not have continuity, replace it. 

Monogram Stove heating element not working 
The surface element board has relays that regulate the power supply to the burners. If one or more of the relays fails, the surface element won’t work. If two or more burners fail at the same time, this indicates that the surface element board is likely at fault. If only one surface element won’t work, use a multimeter to test the element for continuity. If the surface element has continuity, the surface element board might be defective. 

Monogram Stove burner won't light 
The spark modules provides power to each surface burner spark electrode. If the burner is produces a weak spark, or if the burner sparks intermittently, the spark module might be defective. Before replacing the spark module, first check the spark electrode and the spark wire. If the spark electrode and spark wire are not at fault, the spark module is likely defective. If the spark module is defective, replace it. 

Monogram Oven temperature not accurate 
When the bake element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element is not heating. Often, if the heating element has burned out, it will be visibly damaged. Inspect the heating element for holes or blisters. To determine if the bake element has burned out, use a multimeter to test the element for continuity. If the bake element does not have continuity, replace it. 

Monogram Oven light is out 
If the oven light is out, the entire light assembly may need to be replaced. Often the light assembly components are not sold separately. 

Monogram Oven won't turn on 
When the bake element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element is not heating. Often, if the heating element has burned out, it will be visibly damaged. Inspect the heating element for holes or blisters. To determine if the bake element has burned out, use a multimeter to test the element for continuity. If the bake element does not have continuity, replace it. 

Monogram Oven not self-cleaning 
During the oven's self-cleaning cycle, the door lock switch activates the door lock motor to prevent the oven door from being opened. If the door lock motor and switch assembly is defective, the oven door will not unlock once the self-cleaning cycle is complete. On most ovens, you can open the oven door by removing certain screws or panels. Check your owner's manual for further instructions.

Refrigerator Repair

For the home, kitchen and beyond, Monogram manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of Monogram appliance repair from experienced professionals, your local Appliance Helper can help.

My Monogram Refrigerator is Not Cooling 
The condenser coils are usually located under the refrigerator. They dissipate heat as refrigerant passes through them. If the condenser coils are dirty, they won’t dissipate the heat effectively. As debris builds up on the coils, the refrigerator becomes less efficient, causing the refrigerator to work harder to cool down. If the coils are significantly dirty, the refrigerator will not be able to maintain the proper temperature. Check the condenser coils to determine if they are dirty—if the condenser coils are dirty, clean them. 

Monogram Refrigerator water dispenser not working 
To determine if the water supply tube is frozen, disconnect the tube at the bottom of the door and blow air through it. If air does not pass through, this indicates that the water supply tube is frozen. If the water supply tube is frozen, thaw it out. In addition, ensure that the freezer is kept at the proper temperature. The freezer temperature should be kept from 0-10 degrees Fahrenheit. If the freezer is too cold, the water line may freeze. 

Why is my Monogram Refrigerator Not Making Ice? 
If the freezer temperature is above 10 degrees Fahrenheit (-12C), the ice maker will not produce ice cubes efficiently. The freezer temperature should be set between 0 and 5 degrees Fahrenheit (-18 to -15C) for the ice maker to work properly. If the freezer temperature is too high, ensure that the condenser coils are clear of debris and the condenser fan is working properly. In addition, check to see if frost has accumulated on the evaporator coils. If the evaporator coils are frosted over, part of the defrost system has likely failed. 

Monogram Refrigerator ice dispenser not working 
The dispenser control board governs most of the functions of the dispenser system. If the control board is faulty, it may stop supplying power to the entire dispenser system. If only one dispenser part is not working, test each of the dispenser components before testing the control board. It is more likely that a single part has failed. If the entire dispenser system is not working, the control board is more likely to be at fault. 

Monogram Refrigerator not defrosting 
The defrost control board determines how often to run the defrost cycle. If the board fails, the refrigerator will not go into the defrost cycle. Before replacing the defrost control board, first test the defrost heater and defrost thermostat. If the defrost heater and defrost thermostat are working properly, the defrost control board is likely defective. 

Monogram Refrigerator is noisy or loud 
If the refrigerator is noisy or loud, especially when one of the doors are opened, either the evaporator or condenser fan blade may be at fault. First, check out the evaporator fan blade in the freezer behind the back panel. Try turning it by hand. If the fan blade does not turn freely, check to see if the blade is rubbing against something or if something is caught in the blade. Additionally, check the condenser fan blade in the back underside of the refrigerator to determine if it has any obstructions. 

Monogram Refrigerator defrost drain clogged 
The defrost drain might be clogged or frozen. If the defrost drain is frozen, the water will overflow the drain trough and drip down to the bottom of the compartment. If the defrost drain is frozen, thaw it out and ensure that the drain is clear of debris. 

Monogram Refrigerator freezer is cold but refrigerator is warm 
The defrost heater assembly turns on a few times throughout the day to melt away any frost that may have accumulated on the evaporator coils. If the defrost heater assembly is defective, frost will continue to accumulate on the evaporator coils, and the coils will become plugged with frost. If the evaporator coils are frosted over, the airflow through the coils will be restricted, causing the refrigerator not to cool. Check the evaporator coils to determine if they are frosted over. If the evaporator coils are frosted over, test each component of the defrost system. 

Why is My Monogram Refrigerator Leaking Water? 
If the defrost drain is frozen, the water will overflow the drain trough and drip down to the bottom of the compartment. This water can eventually leak onto the floor. Check the defrost drain to determine if it is clogged or frozen. If the defrost drain is frozen, thaw the ice. In addition, flush the drain with hot water to ensure that it is clear of debris.