Appliance Types


Appliance Brands


Article Categories


More Articles


American Standard Furnace Troubleshooting
American Standard Furnace Troubleshooting

American Standard Furnace Troubleshooting

If you're looking for help fixing your American Standard Furnace, look no further! Our comprehensive American Standard Furnace Troubleshooting guide will explain common issues, provide tips, and show you how to read your model's error codes.

Not heating?  
Most likely, either the electrical system providing your furnace’s power has shorted or the power switch has blown. Try resetting your furnace’s circuit breaker. If it has blown, you will need to replace it. 
The furnace’s igniter might either be cracked or faulty. Check the part for cracks, if it is then replace the igniter. If it isn’t cracked, use a multimeter to test for continuity. 

Cycling irregularly?  
Your thermostat might be adjusting incorrectly, causing the furnace to cycle on and off too often. If your thermostat has an adjustable calibration scale, adjust the heat anticipator. If this does not stabilize the unit, you may have to replace the thermostat. 

Not blowing hot air?  
Your blower motor may have completely burnt out. If this doesn’t seem to be the case, then the connecting belt may have simply broken. Test to see if power is reaching the motor. If it does, but isn’t running, the motor has likely failed. If the motor runs but air doesn’t move, the connecting belt has probably broken. You’ll have to replace the belt. 

Blowing too much air?  
The control board regulates the amount of voltage that reaches each functioning part. If the relay that controls the blower motor has failed, it will continually send voltage to the motor. Replace the control board. 
The contact that controls the blower motor on your thermostat may be stuck closed, causing the blower motor to run continuously. Use a multimeter to check for continuity. If it appears the thermostat is the issue, replace it. 

Leaking water? 
Check the drain pipe. 

Starting and then stopping shortly after?  
Your furnace’s flame sensor monitors the burner, detecting whether a flame is present. If it is either defective or dirty, it will not be able to detect a flame. If dirty, clean the sensor using a fine abrasive pad. If faulty, replace the flame sensor.



Related Error Code Pages:
American Standard Air Conditioner Error Codes, American Standard Furnace Error Codes, American Standard Water Heater Error Codes, American Standard Heat Pump Error Codes,

Related Troubleshooting Pages:
American Standard Air Conditioner Troubleshooting, American Standard Furnace Troubleshooting, American Standard Water Heater Troubleshooting, American Standard Heat Pump Troubleshooting,

Related Repair Pages:
American Standard Air Conditioner Repairs, American Standard Furnace Repairs, American Standard Water Heater Repairs, American Standard Heat Pump Repairs,

Related Parts Pages:
American Standard Air Conditioner Parts, American Standard Furnace Parts, American Standard Water Heater Parts, American Standard Heat Pump Parts,

Related Price Pages:
American Standard Air Conditioner Prices, American Standard Furnace Prices, American Standard Water Heater Prices, American Standard Heat Pump Prices,

Related Pages:
furnace service and repair, furnace fix near me, furnace contractor replacement cost, furnace installation near me, local furnace services,


American Standard Furnace Troubleshooting

American Standard Furnace problems

American Standard Furnace broken

American Standard Furnace issue

American Standard Furnace difficulty


Product Reviews:

I had the six ultras 95 installed in my home two years ago by a certified i
I had the six ultras 95 installed in my home two years ago by a certified installer. It has been running amazingly since then. I have devoted myself to yearly servicing and maintenance. I also change the filters according to usage. I use a Nest thermostat to warn me when to change filters based on usage. I also constantly check the water lines for leaks. My advice to any owner of this product is to take maximum care.
Published: June 2, 2019
pickhvac.com Atlanta, GA
Source: pickhvac.com

About four years ago, I had a 91 % American Standard furnace installed in m
About four years ago, I had a 91 % American Standard furnace installed in my newly constructed home. As of today, I had never had it serviced yet it works as well as it did when I first purchased it. These furnaces are also quite popular in my neighborhood. As yet, I haven’t heard anyone complaining. I can’t express the joy of having a quiet, dependable and efficient furnace enough.
Published: October 2, 2019
pickhvac.com Phoenix, AZ
Source: pickhvac.com

By working smarter, not harder, American Standard furnaces are tailored to
By working smarter, not harder, American Standard furnaces are tailored to use just the right amount of energy for your home. Available in a wide array of options, the brand ensures that they have a potential furnace for almost every Canadian home, no matter the conditions or budget.
Published: November 2, 2019
furnaceprices.ca
Source: furnaceprices.ca

The American Standard furnace was installed in my house about three years a
The American Standard furnace was installed in my house about three years ago and runs without any problems whatsoever. It’s efficient, quiet and heats up well. I couldn’t ask for a better furnace.
Published: March 2, 2019
pickhvac.com Atlanta, GA
Source: pickhvac.com

I had my old American Standard furnace replaced a few months ago with a new
I had my old American Standard furnace replaced a few months ago with a newer model of the same brand. It was still working fine, and the only reason I had it replaced was because I knew that it was quite old. I found the serial number after it was removed and did a search, only to realize that it was more than thirty years old. Quite phenomenal! I hope that the newer model functions as well.
Published: September 2, 2019
pickhvac.com Edmonton
Source: pickhvac.com

Visa MasterCard

Site Secured By The Website Guardian
TOP