I loaded and ran the GE Profile dishwasher in the evening. Later that evening, putrid odor of undetermined origin was noted in the house. I searched throughout house to find the cause, but it was not located. The next morning, the dishwasher was found to be extremely hot on the outer surface (door) and countertop. The heated dry light was on along with the start button, which would not reset or turn off. The unit had to be disconnected by turning the electrical breaker off. All contents were either melted or had a strange brown film, along with broken tines and melted silverware rack in the dishwasher. Even the water dispenser in the bottom of the dishwasher was melted or broken. A GE service representative was called and his report stated: Unit was left on for too long and heat caused excessive damage to the product. Due to excessive damage, unit is non-repairable. He shared with me he had never seen this much damage done to a dishwasher. I spoke to GE consumer advocates twice and their solution is to provide me a discounted price on a new appliance and the email address for formal complaints. When I inquired about if there had been resolution to the cause of this problem because I wanted to make a formal complaint, I was told there is not a safety issue with the heating unit. I then spoke to a GE resource person in recall and she shared with me that it is a known issue of overheating and destroying contents, but it has not caused a fire. Igniting a fire is a justification for a recall - can we not be proactive? This department is working with me and ensured that in newer models this potential hazard does not exist. But other consumers who have purchased in this model (PDW9280N20SS) should be aware of the potential fire hazard. Everything was very hot inside and out. Consequences: the 3-year-old dishwasher (that I use about once per week) was totally ruined and I inhaled potentially toxic fumes for over 8 hours.

I love the GE. I bought a GE dual fuel range about 3 years ago when my 6 yr old Frigidaire stove caught fire. Always wanted to cook with gas but have electric oven and broiler. It's also easy to clean the cooktop unlike older gas stoves. Love the big fast boiler eye.

Microwave (GE 2.2 PROFILE) was manufactured in Oct 2015, I ordered in November 2015 and it was delivered January 2016. Installed in March 2016. Was making rattling sound like the case was loose or something. The other night I placed cup of water in microwave, turned on for 1minute and FLAMES shot out (on the inside) from the “squares” on the inside. Does it every time so unplugged. Contacted GE. Was told Out of warranty. Repair person can’t come for 2 weeks. Waiting for return call from customer support. I don’t think flames can be fixed!!

Called in for my washing machine and got service on my dishwasher??? With a bill of $207. A scam. Please take my advice and never call GE.

The way you put bowls in this model doesnt allow for cleaning them completely. You must wash the bowls AFTER cleaning them in dishwasher. Waste of time & money. Capacity smaller, noise louder. Not good value.

Purchase a GE microwave Jes1142sp2ss on December 2014 from BrandsMart. The paint on the bottom of the microwave is peeling off exposing the metal. I have never ever heard of this happening on a microwave. I will never buy another GE product.

I called the toll free number because of the concern I am having with your microwave, the paint is coming off the inside. So my concern is first why would it be coming off, is it a defect in the product or does it just happen? The person was helpful and seemed as if it was to be concerning. WELL IT IS to me. Could it make us sick, do I need to put it in the trash or what? Thanks for not helping me and not being concerned, but I am sure if it was you or family you would have had a different story to tell.

This dishwasher is less than 4 years old and the rack is rusting away. It seems like it happened overnight. I didnt notice anything and then all of a sudden the first is everywhere! The metal inside of the plastic is even disintegrating. It seems like it was rusting before the plastic coating came off. The only good thing I have to say about this dishwasher is that it is quiet. At 4 years old I dont think I should be having to replace both teams!

Unit is only 7 years old and not greatly used (only two adults who dont use it much)… Purchased as part of package including GE refrigerator, range and dishwasher (already got rid of refrigerator, as parts kept breaking and unit had other chronic problems). I turned the microwave on to make popcorn - it immediately made a terrible noise and filled with smoke with an electrical smell. Unplugged the unit and contacted GE Repair. When I described what happened, I was transferred immediately to their safety unit because of the nature of the problem. A GE technician arrived today and almost immediately diagnosed the problem: a metal component that directs the waves of the microwave generation tube had burned out, and by federal regulation, he claimed, cannot be repaired - the whole appliance must be trashed and replaced. Once again, I have experienced GEs poorly engineered products that appear to be designed to fail in a relatively short time. Can you spell planned obsolescence? (No photo provided, as there is no external visual damage).

A known GE microwave defect on this (GE JVM2070SK02 Microwave) models control panel has yet again resulted in our microwave not working and GE giving us the standby, pay for an appliance technician. I would like GE to own up and send a technician to replace the control panel and get it working since it’s a known issue.

GE above stove microwave (DVM1850DM1BB) stopped working and went completely dead after 1 year. Purchased a second GE microwave because it easily fit into the existing space. Sure enough, the second microwave stopped working and went complete dead a little over a year. I have always heard bad things about GE products, now I can confirm those negative comments about GE products are true.

GE Cafe Microwave CVM2072SM2SS - The touchpad stopped responding, like many other who have had this issue. GE would not give me a break on replacing the main and supporting circuit panel as suggested by the technician, so I had to pay out $500 on my own. After less than a year now the microwave wont heat. I liked the units looks and display but if it wont work, its useless.

My GE microwave oven died after 4 years. And my GE washer died after 5 years. Never ever buy a GE appliance. The market agrees, because their quality issues might be the reason the company has not been able to sell their appliance division for several years now.

Model GLD5660V00SS - seems to be an entry-level dishwasher compared to others I have used/had in the past. It is rather small inside - usually have to run it every day or every other day for just two of us. It is plastic inside and the wheels have already come off a couple of times even though Ive only been using it since July. Having said that, it does a decent job cleaning and is easy to load. The outside with the stainless panel is attractive and the controls are easy to use. It has a large, removable silverware bin that keeps silverware from nesting. However, the holes are not large enough for the knives to fit in properly. The tops are removable, so I can just put them in another section.

I purchased a this GE Model CDT845P2NS1 on Oct 2, 2019 and the unit was received Oct 23, 2019. I installed the unit approx. 4 days after receipt and dishwasher functioned well until November 10th, 2020 when the unit failed to pump out the water. I contacted GE Service (MabeService) and was advised that the unit was not under warranty and as such I should contact a GE Canada authorized service centre.After several attempts to get someone to come to our location at Sharbot Lake we got hold of Capital Appliance Repair in Ottawa. They were not able to send a technician until November 18th. After diagnosing the problem the technician advised we needed a main control board and would have to order one and then come back to do the install of the control board. It is now February 21st 3 months after the visit and I’m being told that the part is backordered and they have no idea when it will become available. I’m extremely unhappy when you spend over $7,000.00 for a GE CAFÉ gas stove, Microwave, Refrigerator and dishwasher to find out you cannot get parts in a timely manner. As a customer of GE Canada I have had no help is solving my problem. It is not acceptable to have a 1 year old dishwasher that has failed, much less waiting for repair that has taken over 90 days to get repaired. DO NOT BUY!

Have had my GE dishwasher for 15 years. Had initial problem with inner liner pulling away but got GE to replace unit. Has worked fine ever since. Nothing fancy just gets the dishes clean. Would have liked a bit more adjustability with the shelves.

We purchased this new 8 years ago however the problems started after about two and a half years of use. I called GE when the paint started peeling off of the door of the microwave. They asked me if I cooked salty foods. I cook bacon in the microwave. They told me my only option was to buy a new door and have it installed. It was $250 at the time. I did not have the money or desire to fool with it. I continued to use the microwave and it has continued to degrade. Now eight years later there is so much metal showing that we decided we must do something. It is unsightly and very difficult to clean because its rusting. Ive been expecting electrical arcs to occur and the microwave to catch on fire. It hasnt done that. It has continued to cook the food. The entire metal area on the door is without paint. There are other large areas of metal and rust inside on the bottom of the microwave. The entire vent panel is without paint and rusted. We also had to have the control panel replaced twice. It was covered once under the warranty and once it was not. We also had to replace the element in the oven which is used rarely. To replace the microwave and oven combination now would be $3,500. When I do replace it I will replace it with a different brand.

I know this commonplace complaint, like thousands before me, will head straight into the wind because the world just works in this way: technical support and repairs works as a profit center for a corporation. My GE Profile microwave abruptly failed out of warranty after years of use. The cause was due to a wire burning up inside that had not been loosely connected, said the GE technician, so this was an issue of inadequate quality--not bad enough to cause the microwave to fail quickly but enough to cause failure over time.After taking the microwave out of the built-in cabinet, it only took the technician about 5-8 seconds to find and diagnose the problem, several minutes to get the right part (a wire) from the truck, and a couple of minutes to fix it. The labor charge was $121 for about 7 minutes of repair work, to be liberal with time. (This charge is separate from the charge to come to our home and diagnose the problem.) This prorates to over $1,000/hour for a basic wiring change, which I think is exorbitant. I understand that the technician is a highly trained individual, but this is already reflected in the high labor rate.According to GE, the cost to replace the built-in microwave, which came with a matching stainless steel frame would be $550 if we wanted the new microwave to match the frame at least (but not necessarily the oven, stove, etc.). This is the kind of cost you dont think about when you buy a new home built with matching appliances--well, I didnt. Companies like GE can rationalize all they want about all the overhead associated with servicing a repair call. I can certainly grant them some leeway, but in the end, charging an extra 8 times more an already high labor rate given the time needed to fix the problem is simply price gouging a consumer who has no good recourse. (This is why I pretty much avoid repairing anything, except for my car. Its almost never worth it.)I recently had an experience with an experienced plumber charging an hourly rate of $150, prorated by and rounded up to half-hour increments of work, regardless of difficulty of work. Repairing an appliance should work the same way, and my GE bill would have been halved. Because of such profiteering, I will not consider purchasing a GE appliance in the future. I pray that this microwave doesnt break down again in the coming years due to some other problem. It would be a lot less expensive to just buy a non-matching portable microwave then for $100-$150 than to keep up appearances.To be fair, the woman who fielded my service call was courteous and empathetic. Because the microwave apparently had an electrical burning problem, she previously waived the diagnosis fee. Otherwise, my simple repair would have run several hundred dollars, more than the cost of the microwave. However, she was unwilling to reduce the labor charge, so based on how strongly I felt ripped off, I give GE a star rating overall.

The key pad says it is shorted out and needs service. It turns on randomly. I unplug it and plug it back in and it will either say service needed, keypad shorted out’ or press clock .I dont use it much for microwave cooking. It came with the house we just bought and it only worked for 3 weeks before it started this mess. I could deal with it if it didnt beep all the time.

I owned a previous GE dishwasher 4 years ago and would give it excellent ratings. I bought a newer top of the line version when I purchased a new home. It simply fails to clean dishes. Wet food that any dishwasher would remove, remained on the dishes. The drying cycle never dried the dishes. We have to hand wash the dishes now and have stopped using the dishwasher after 3 days of ownership because of health hazard. I called Lowes about this within days of the install. Lowes sent out the installer who claimed the machine was installed properly. Then Lowes scheduled a GE repairman to come to the home. We waited all day for him to arrive for a morning appointment. He never came. Lowes stepped up and is replacing the dishwasher with a non-GE product. I would not touch a GE product again given the lack of service and commitment to their product. I feel confident with Lowes, but not with GE - their ethics from engineering, manufacturing and servicing are very suspect with us.

Microwave performs wonderfully but it has peeling paint inside. I contacted GE about it and the only thing they said was, Well give you a coupon for money off another GE microwave. Why if I had money to buy another microwave would I purchase a GE and watch the paint peel off again. I am retired on a fixed income. New appliances dont come easy.

We have a GE built-in combination oven and microwave. The oven gets up to heat very quickly and bakes in less time than recipes call for baking. The microwave is an 1100 watt unit and performs equally well, and has for 29 years, Our cook top is a GE glass top unit, installed 11 years ago in a kitchen upgrade, performs equally well, though not quite as fast heating as our old gas unit but much cleaner and attractive. Have never required a service call on any of this equipment!

First Profile microwave/oven caught on fire. Was replaced. Front panel on Profile refrigerator not reacting to touch. Repairman said that this model had problems. Fixed it - cost over $100.00. Dishwasher (Profile series) not worth the cost of heating the water to run it. Cleaned dishes by hand. Stove top died - not reacting to touch. $90.00 for repairman to visit us, and another $60.00 to tell us what was wrong. A lot of money for inferior products.

My GE microwave is the Advantium version which’s heats to a 1000 degrees. In fact, today the 4th of July I will be using it instead of the BBQ. I have baked, broiled, heated and other things in this unit. This is my 2nd one over the years and I enjoy it immensely.

Touchpad for CVM2072SM2SS stopped working. This touchpad has been creating issues for the last couple of years. Few reconnection of wires got it working for the last few times and now it is completely broke. GE is not ready to help with fixing the issue. It wants to sell me another microwave CVM1750SHSS which seems to have similar issues (also the plastic handle for those microwaves seems to fall apart due to heat). In fact, the reviews for the whole range of GE Cafe series seems to be pretty bad. GE is not owning up the design issues. Too bad!

When we purchased our home it came with GE appliances which was covered under a one-year warranty. My microwave has been broken for nearly 3 months. It is almost impossible to get a service tech to come out immediately. GE customer service is the worst I have ever dealt with. They are unprofessional and unreliable. Most of all uneducated about their job. If I could return all of the items in my house that were made by GE back to the seller I would in a heartbeat. The Appliances are poorly made and the customer service is too difficult to deal with it. It’s not worth the money or the Headache... Stay away from GE appliances.

GE Profile Microwave JVM1850DMCC - For the third time in 5.5 years, Ive experienced a magnetron failure in a GE Profile Microwave. The first failure was fixed under warranty. The second was so bad, the microwave had to be replaced, but it was no longer under warranty. I should have heeded the warning and gone to another brand, but on 12/31/10, I paid over $500 to replace the microwave with a new GE Profile to match the existing appliances. Apparently this was a big mistake as the magnetron has failed yet again. The microwave is on its own separate 20A circuit, so that shouldnt be an issue. It would seem, however, based on the number of complaints I see on this site, there is something inherently wrong with the manufacture of these microwaves, or more specifically the magnetrons. Im extremely disgusted at this point.

As a landlord I have about 20 GE microwaves. I have had 8 handles break off in the last few years including the one in my house with me pulling the door open. Standing straight in front of it, just pulling regularly. Replacement plastic handles - just two pieces of injection molded plastic - selling from other companies for as little as $10 are $130.00. $130.00! There is a clear design defect here and the companys solution to it is to charge $130 for the plastic replacement part. Someone should go to jail. Literally. Please include me in the class action lawsuit.

Had 2 G.E. microwaves make a loud popping sound (like a boom) while turned off and then they started smoking like crazy. 1 model #JVM1630BB004/ serial#MA9713685. The previous microwave was just thrown away. I didnt realize there was a problem with these G.E. microwaves, so I dont have the other model/serial #s. These are a real danger.

June 18, 2018 GE Spacesaver Microwave in use when there was a loud pop, heavy smoke boiled out of the unit and strong smells of wires burning was noted. On fixed income now what do I do? Understand my microwave has been reviewed by ConsumerAffairs for the same issue in the past. Whatever became of their investigation?

A small black piece of plastic, which snapped into the back of the microwave handle has bent/shrunk, and popped off. My microwave is just a little over one year old. I called the GE 1-800 phone number for parts, and GE does not offer a replacement part for this, without buying a whole new replacement handle, which costs over $160.00.

Nothing happened...never has. It just wont wash dishes. I have to prewash every item that is put into this piece of garbage. I bought it new and have used it for 3 years. It remained in the box the first 5 years I owned it and it honestly did me as much good in the box as it has since we installed it. It makes a good rinser but wont even wash off a lemon seed left in the bottom of a glass. This is such a joke. I would never buy another GE product. The refrigerator I bought at the same time, a side-by-side, the entire front door froze solid within 2 years and we had to buy a new one. Your company stinks. This is a rip off of my money. Refrigerators and dishwashers are not cheap. Model GSDL122F02BB is the dishwasher.

After about 5 months of owning the unit (GE dishwasher model GDT580SGFBB), the door latch sensor became defective and discontinued the wash cycle up to 6 times every use. I contacted the GE warranty department. Their consumer relations advocates treated me as subhuman. I never felt like a valued customer, my concerns and my time were never a priority. Instead I became a part of their research and development program while beta testing a defective product.After 6 months of futile repairs requiring multiple technician visits I was exasperated. I had submitted 4 separate warranty claims that often were mysteriously closed without my knowledge. I finally contacted the original retailer, Home Depot, and shared my experience. They catered to me even though it was well past the 90-day store policy. They gave me a credit for the purchase price so I could choose a replacement. Since I dont want to touch another GE appliance with a 10-ft pole, I chose another brand. Shortly thereafter I received a call from GEs Escalated Issues department offering to replace the unit. Evidently that lit a fire under them. But it was too late, my patience with GE has been exhausted. If this is the way GE wants to run their business, then it will be a fast-track way to dig their own grave.

My GE dishwasher is just OK, I would say. It saves water and money. It is fairly efficient to load and pretty effective at washing on normal but many times I need to hand wash the big or hardened food off the dishes before loading, which feels like more work than should be necessary. Id rather not wash my dishes twice.

Purchased a GE over-the-range microwave worth about $400. About 2/1/2 yrs in it stopped working. Had a GE repairman come out to fix it. They charge $95 just to come out. I complained so they gave me 50% off parts and labor after the initial investment. It took him about ten minutes to pull out the defective part, a $10 thermostat which he replaced. Total cost: $162. Ive had GE products for years but the new ones are much more cheaply made IMHO. Made in Malaysia. In addition, the handle is breaking off as are plastic parts coming of the top of it. I guess Ill consider getting extended warranties from now on because these products are cheap. If Id had it longer, Id have bought a new one instead of fixing it.

Dishwasher has been running 3 hours and it still has not finished. It is the loudest dish washer I have ever owned and this is the 5th house I have owned. To top it off I just paid $270.00 for a GE professional to come to our house to troubleshoot our problems and it fix the issues. Guess what, problem not fixed and GE has my hard earned money. Thanks, GE.

My 4-month old dishwasher started to leak so I called GE to repair since it is still under warranty. Technician said there was a superfluous piece on the gasket which he removed. Dishwasher was fine for about 2 cycles when it started to leak again. As GE do not have a weekend service I had to take a second half day off work. Different technician said the gasket was not pushed in correctly and I should check it each time before running it. Shouldnt this be part of the design - a gasket that stays put?! Ran the dishwasher. Water all over the floor. The new floor that is getting ruined by this clearly faulty appliance.

G.E. Spacemaker over the stove microwave. This is my second microwave of this type in 14 years. The first one lasted only 5 years. Im satisfied with the product albeit the price tag is too high.

I have microwaved many types of food in mine! Remember, it’s not just for reheating leftovers! I have cooked fish, and chicken successfully. Those turned out juicy and tender. I follow directions from a microwave cookbook. It’s easy and clean up is a snap.

Its an older Hotpoint, and the layout is fairly roomy for a dishwasher of its size. The last apartment I was in had a comparably sized dishwasher that had too many shelving elements that got in the way of being able to just shove some dishes in there. Ive discovered with this dishwasher I need to stick to powdered detergent because the Hotpoint doesnt fully dissolve tablets. It does a fine job overall, though.

Its a over the range model & came with a house purchase. It’s worked flawlessly for over 5 years now - even after being left with no air conditioning in FL for months on end. The only thing I could think to make it better is making it easier to choose longer length cook times. Button for half min & dial for all the rest can be irritating for your 16 min food.

Our microwave came with the house so we didnt choose it. Ive had a bit of trouble with the rotating mechanism making knocking noises a few times which Ive been able to finesse by exploring troubleshooting online. Other than that its been dependable for 4 years.

My husband and I replaced all the appliances in our new home 4 years ago with GE Profile double oven, cooktop and built in microwave. All the appliances are of poor quality and do not cook the way we are accustomed to. But the microwave has had a particularly bad history. Within one year, it completely quit working and we had to replace several fuses and a board. Over the past couple of months, the keypad continually quits working and we have to climb up on a stool, unplug the microwave to reset it. Only then will it work for us to heat something. However, the keypad does not accurately reflect the task we are trying to use. I have had many microwaves over the years and I have NEVER had to repair one before. This particular brand of microwave was produced in Malaysia in July 2008. Very, very poor quality. No resolve from GE or from Sears where we bought it. I am done with GE and with SEARS.

I have a built in model that is now 9 yrs old and still operates as well as the day I bought it! I will definitely buy GE again. I have family members that have owned 2-3 microwaves to my one, that screams quality.

I just dont know how to start to show how disappointed and upset Im about this Microwave. I know GE is good brand but this Microwave must be the worst. I bought this microwave between July or August in 2016. Unfortunately, I lost the receipt. I bought a cash at Home Depot in my area, because I bought it cash Home Depot unable to find a record of but they remembered I did buy there between that time. I know bought that time because I bought my house in July 20116. This microwave started giving problems since June 2017. When I call GE they told me, they cant help because I dont a receipt, and they told from their record, this microwave was purchase in January 2015, they didnt want to believe that I purchased it in 2016.They charged over $100 to have a technician to come, he has to order a part that cost as well over $100, when the part comes another technician came. It was the wrong part. He had to order another part. The technician came back and Microwave work for only 1 or 2 months and stop working. Its been very stressful with this Microwave. This microwave was the most expensive, I bought over $500-600. Even though from your record you said I bought it in 2015, it still unfair, no one expect to buy something that expensive and break down that fast. I dont what to do. Im just so frustrated about the whole situation. This microwave cost me about $ 1,000 now from price to repair, and yet still not working. I wish someone reply to me and help me, if no one help I never wish to buy a GE product. So Sad GE, I need HELP.

I have a GE dishwasher installed by our builder. It is 6 yrs. old and for 6 yrs. it has been a problem. I already had it serviced in last years recall and now I get another notice. It is located close to our TV viewing area. and is so noisy. I hate to run it when we are watching TV. I would never buy another GE. We are also having problem with our GE double oven. I ruined several holiday dinners before realizing the temperature was 75 degrees where it should be. A replacement part is almost a $1,000. I would never ever buy another GE appliance.

I had a new house build and it came with all GE appliances. The dishwasher Model GDT530PSD255 was not drying the dishes and the run time could be as much as 3 hours. The service man was there with in week. He said the dishwasher was working properly. After running through the cycles he said its working just fine. I open the door and it was all wet and the silverware tray and the silverware was wet and some soap was still on the door. He said everybody complains about the same thing. High efficiency Dishwasher have long run cycles and most dont dry to well. The silverware trays hold water because the tray sides are flat (horizontal) and that holds about a half of cup of water. All they have to do is put them on a 45 degree angle and the water will run off. Apparently it worked well on paper and no one actually ran it through its cycle. Needless to say I hate this dishwasher and its almost at the point to do them by hand. A lot of time is spent drying off dishes and silverware.

First off: GE doesnt make some parts for this model anymore. The unit is large compared to many others; the upper tray provides adjustable height; one of the set of spikes in the upper tray rusted out because of inadequate plastic coating, and no replacement was available from GE; the control panel on the top edge of the door failed within warranty period and was replaced free; the holes in the rotating arms that spew water upwards onto the dishes must be cleaned with tweezers to remove bits of paper from labels. Those are all the negatives. The positives are that it is very quiet; a cycle takes about an hour; it cleans dishes well so long as they are not hidden from the water jets; pre-rinsing can help but is not necessary. I would buy it again.

The paint started peeling on the inside ceiling area of the microwave the end of the first year we bought it. I called GE and they claimed this was not harmful to the operation of the microwave. It was disgusting to have paint chips falling onto food we were cooking. Now almost all the paint is gone and there is some rust too. How can this be for cooking and what if some of the paint is accidentally ingested? If GE did not replace or offer to repair the problem. Stay away from GE microwaves is my advice.

GE microwave model JES1344ES. This is a stainless steel with black accent 1.34 cubic foot microwave oven. It looks great. The micro is heavy for its size. The stainless steel is brushed and low luster finish. The door handle is chrome as is some of the other accent pieces. The push button panel is easy to read and has a large knob for making manual time adjustments. The light inside is very bright. There is a rotating platter in the oven compartment that is not knocked off of its guide rollers very easy. The push button panel is a glossy black material that is easy to attract fingerprints. The preset times that are programmed in the microwave is the only part of the product that could be an issue. For example the popcorn button when used has burnt all of the different brands of microwave popcorn that we have tried. It is set about 30 seconds too long. There is no way to adjust the preset time that I can figure out. We set the time with the large knob manually and the popcorn comes out just fine. The preset times for the Auto Defrost are also a bit off. They are not long enough. We also have a Subzero freezer set at minus 20 degrees Fahrenheit so that may be too cold for the defrost presets. Overall the microwave is great except for the preset times that Ive mentioned. We use it daily and have done so for five years. It still looks excellent inside and out.

My GE Adora microwave is about 6 years old and for the last year it has had an issue with moisture in-between the glass front door. It was streaky and now I have cloudy blotches. Called GE repair and it would cost close to $90 just for service call not including parts/labor. Think twice before purchasing this microwave. Not a happy consumer.

I was heating up some Mexican food and smelled plastic burning and looked in the microwave and saw one plastic knobs that hold up the metal grill on fire. I blew it out. I have GE repairman come out to see if they could fix it, and he said that happens and they were not responsible for it. I told the repairman to get out of my house as GE has built a product that can burst into flames and will not address that they are at fault.

My experience with GE over range microwave oven (built in) as follows/ Unit Mod.JVM3160RF3SS. Ser.#GG248367A, this unit was produced April 2016. Review February 28, 2019, unit began to disconnect itself during normal use. This was done by way of throwing 15 amp breaker. New home with dedicated circuit = Yes. Online Problem shows indoor sensors interlocks not adjusted properly. Troubleshoot fee minimum $99 with parts estimate $250.00. We have been limping along for two months with frequent trips to basement resetting breaker, now the breaker trips when activated. Same thing happens on multiple circuits, via extension cord trial. Next step purchase NEW MICROWAVE that is not GE.

Dont buy one. I bought two last year. The first one completely died before the 60 days were up. I took it back to Sams club and bought another. The tag inside says it was made February 2011, so its only a year and a half old. Under the carousel, the paint is peeling big time. I wrote GE repeatedly, asking if it was still ok to use it. After ignoring me for quite some time, I got this reply. In the notice, they told me to get Sams club to replace the defective and apparently unusable product they are selling knowing it is defective. I love the part where you cant cook something with too much liquid in it. Who does that when they microwave?Heres what they said: Thank you for contacting GE regarding your microwaves and the paint peeling issue. I did some research on it and found that it a common issue among all brands. Excessive heating of un-covered liquids can create a high amount of condensation that the inside paint is not meant to withstand. Minor chips to the coating on the microwaves interior cavity will not affect the products performance. However, if the coating is actively flaking or peeling anywhere inside the oven cavity (including under the turntable), discontinue the use of the microwave and replace it. GE does not have an approved method of repair, and the microwave is not repairable. Please return to Sams club for an exchange, if you are still within the one year warranty. If Sams is refusing to accept the return, contact the Sams Club Support Team at 1-877-885-2787. GE will then reimburse Sams club.

We purchased this microwave in 2016. It worked fine for a few months then one day we go to use it and it would not start. It took pushing the start button 5 times for it to work and the express cook did not work. Then 2018 came and it was November 2018 and the microwave started to short out and started smoking. So we bought a new Panasonic microwave and so far so good. Would not tell anyone to buy a GE brand item ever again.

We bought a brand new GE kitchen. We put all GE in the new kitchen. The hood/microwave/convection oven broke in 9 months. We had service out, and they wanted the same amount we paid for it to repair it. My husband is an engineer and he got it to limp along. Then in September, it broke and cracked up. All the control panel cracked and broke. It does not work. We called GE. They said to get a replacement. We went to Sears and bought a similar unit as the original has been discontinued. We were assured of a credit towards the new one. A credit would not be issued. Gary ** has continually called my home but not my cell. He reached me today in school, a Special Ed behavioral unit, and started yelling at me over the phone. He said that I did not provide serial numbers. I have many times. He said there is no record of my complaint. I have called, emailed and written at least 3 times providing all information. We just want a credit for the original unit. We have provided sales slips, etc. Please help.

We bought all new GE Cafe kitchen appliances when we remodeled our kitchen 3 years ago. The first Cafe dishwasher needed repairs in the first 3 months, and was replaced within 10 months due to continuing problems. The replacement GE Cafe dishwasher was deemed non-repairable after 2.5 years. The unit has a design flaw and the bracket holding the top water sprayer broke. The extended warranty with Assurant will not cover the dishwasher because they say it is not a working part. We are trying to get GE Customer Care to help but after three weeks the message we are getting is they do not care at all.The front burner on the cooktop will not light. GE cannot get a replacement part so the cooktop was also deemed nonrepairable after only 3 year. Our Cafe refrigerator also has a design flaw. The refrigerator must be unplugged to reset the computer when the water filter is changed. If you dont the refrigerator does not recognize the filter and will not dispense water. Needless to say I will never buy GE again. It is sad to see what was a good company go down the tubes.

Bought a new GE dishwasher. Arm on top keeps falling off. Does not heat dry. Dishes do not come out clean. Had repair man out four times, still not fixed. GE junk, junk. Will never buy GE again.

My husband and I purchased a GE dishwasher model: P GDWF150V55ES, serial no: SZ768478B on October 20, 2012. The dishwasher never worked from day one. I have had so many hassles with the consumer relations department. They are the WORST EVER!!! I have been fighting this company for over a year. I have provided photographs of filthy dishes and utensils. They dont care. We are a middle class family and we have been ripped off by GE. I will NEVER purchase another item from GE and I recommend that nobody else does either. This has been a nightmare for us.

The new home that we purchased had the above named dishwasher (GDT655SSJSS). When I run the dishwasher there is a very high frequency whine throughout the cycle - the only time it stops is when it is changing cycles. I have contacted GE Customer service 3 times... The first time I was told to add a quart of water to the bottom of the dishwasher and that should fix the problem. Tried that - still high frequency whine. Second contact - no response. Third contact - today- called customer service after my negative appliance review was rejected by GE (buyer beware of all those positive reviews) and was told that this noise is normal. Totally Unacceptable - since the sound hurts my ears and causes a headache - I have to listen to 111 minutes of this noise (except when the washer pauses to change cycles). This is the very worst dishwasher I have ever owned and even though it is only 2 months old I will be replacing it - and it wont be a GE Dishwasher.

I have had my GE microwave for over 6 years and the paint is flaking off the inside of the microwave, causing a health and fire hazard. Paint chips in the food and bare metal exposed can cause arching which in turn can be a potential fire hazard. After researching online I have found that this is not a uncommon problem with GE microwaves. Some have had this issue after 1 year. I contacted GE and told them of the problem and that I felt this was a manufactures defect.GE does not feel that this is a defect problem but advised me not to use the microwave any longer. Their solution was to discard this microwave and purchase a new one. I paid almost $300.00 for the original one plus $20.00 for a mounting kit. I was told that GE would offer me a discount on a new one from $339.93 to $319.93 total. This is not much of a offer considering this should be a obvious manufacturers defect. By ordering another I will have the same problem again. GE needs to stand by their products and admit fault.

Dishwasher is 3 months old and today is the first time it has worked! GE has sent repair techs 3 times and finally today the unit was temporarily repaired with electrical tape attached to the brand new door latch. The door latch is cheap plastic and has a manufacturer design defect of being too small to properly engage the unit when the door closes, thus not allowing the cycles to start just a series of beeps. No other manufacturer uses a cheap plastic door latch designed like this but GE! Piece of crap, dont buy it!

I have had this microwave WES1130 for several years now and the paint began peeling before year two. Nearly all of the paint is now gone (fallen into my food). Also, I bought this microwave to replace a larger GE microwave that had failed after only 3 years. The 8-year-old GE fridge is humming loudly and leaks onto my floor, which has ruined the wooden floor and warped it. I will never again buy a GE product, and neither should you. They do not care at all about quality.

GE profile microwave magnetron burned out after 2 years. Part is supposed to be under warranty, but repair is not. There are no service centers in my area. GE wont just send me the part, or let me send them my old part.

Always works well, cooks great, could use a little more space. Had GE microwave in the past and it never let me down. Had this one for 2 years now and no problems with touchscreen, door hinges or settings. Owned Maytag before and had nothing but problems.

We purchased the suite of Cafe appliances. After one year of service, out of warranty of course, the touch pad on the microwave quite working. The touch pad on the dishwasher has several lights that do not work. These products are insanely inferior. If you are considering purchasing, I would buy anything but GE.

When the handle on my expensive replacement (GE Profile for GE Profile) microwave/convection oven peeled, we called our retailer (PC Richards is really good about service). A new door showed up and it, too, has a plastic handle. The difference is, this time its solid grey plastic as opposed to white plastic with silver paint. Seems to me that an expensive SS appliance should have an SS handle. Too heavy? Just use a tube of SS - not solid. Too hot if above burners? Didnt my last GE Profile micro/convection have a SS handle? I spoke with customer relations. The person was well trained not to say anything that might suggest she agreed with me. Since the issue is cosmetic and not functional, I have to consider the issue dealt with now that the door has been replaced. I told them I will do my best to publicize this issue and that I will never again purchase a GE appliance. I also called CEO Jeff Immelts office in Connecticut. I made it clear that my dissatisfaction has cost them a long time, loyal customer and that I would spread the word. I would appreciate if anyone agrees with GE that a SS handle would be too hot over stove burners.

GE had recalls on models 8500 and 8700 due to the motor catching fire but not my 8600 which is right in between. So besides it being the worst working dishwasher weve owned by not even cleaning well, the unit catches fire and almost burns my house down and GE wants to give me a credit toward buying another fire trap as opposed to replacing it because its 5 years old. I expect appliances to last more than 5 years and not catch on fire. No more GEs for me!

Have a GE dishwasher put into operation June 2016 (new home). In Oct 2016 we noticed a leak and a serviceman came out and identified a loose soap dispenser - tightened it. Next time we used it, leaked as before. Same serviceman came again, this time replaced both the main seal & spinning water distribution wand assembly. Again, the unit leaked and on Dec 14th same serviceman replaced the soap dispenser. Before he got too far down the road, we called as the unit again leaked. He blamed it on excessive soap suds - which he removed manually. Following his departure, we again experienced a leak. Same serviceman returned on Dec 15th. After review, he advised us the DW would be replaced and we should get a call within 48 hrs to arrange. On Dec 17th (still no followup from GE) the DW leaked again - we video this time. On Dec 19th called customer relations and after much discussion it was apparent GE has NO CLUE what the heck they are doing. ONE MORE repair trip was scheduled - this time they would replace the inside and outside panel! We are fortunate to be retired otherwise this repair process would have cost us about $2000 so far! How idiotic is GE?? How much have they spent to avoid replacing this unit? Believe me this is the LAST GE appliance we buy from them. Dont know how they stay in business. We are awaiting the panel repair guy as of this writing. Will update once this service has been completed.

We purchased a new home with a GE Profile dishwasher installed. Since the day we had it, we have never been satisfied with the cleanliness of the dishes. They frequently come out covered in food and must be rewashed. We now routinely prewash everything in the sink and we always use the cookware setting to wash everything. Despite this, we still have to re-run loads because they are not clean.I am convinced that there is a design error with our dishwasher, because the top dish shelf obstructs the door of the soap compartment and prevents it from fully opening. After a load has run, you can still see leftover soap dried and crusted in the soap container. If the dishwasher cannot even wash the soap out of the soap compartment, no wonder our dishes are not clean.

We had some oil spill in the oven, which proceeded to catch fire. It was a huge fire that burned for a while. But all it took was a little oven cleaner, and it looks like nothing ever happened! The coating and materials inside of the oven are completely fine. It also still works perfectly! I'm amazed. 10/10 stars.

I have had this GE microwave for over a year now and have not had a problem with it. It has a variety of settings and it doesnt quit if something causes a spark/feedback, like a tiny piece of foil. It has a spacious interior and a large turntable. Also, the light stays on while cooking and comes on when the door is opened allowing one to watch and check on the cooking process even in a dim night light environment. Mid-morning munchies without having to turn a bright light on. I have tried other GE products and was disappointed with their performance. This GE microwave has worked well and I have not had any problems with it.

First, as a new homeowner blessed with select builder-provided appliances, I never imagined I would be authoring this letter 4 months after closing on the new home. Your friggin’ microwave oven light mechanism truly sucks! I lost the two bulbs a week or so ago and purchased two more at the cost of approximately $10, even though a one-year warranty was stated. That was okay, as I was more interested in fixing the problem versus starting some long-range purchase interest. So, and this is the most aggravating aspect, I have the correct pins and life is ** good, and as I attempt to insert the first, the ** pin breaks off. Okay, so I reflect on the horrific engineering of the mechanism, and I softly” align the second of the two bulbs, and the ** pin breaks off again. ** is my predominant theme tonight. As well, believe me, I am going to inform Taylor-Morrison that their respective selection of your friggin’ lousy pieces of crap is corrupt and misguided. You suck, G.E.! I’m moving forward.

I wish I had seen this site first. I purchased a dishwasher. It didnt even make it 6 months. Took a month to fix and then 3 months later broke right before Thanksgiving. It is now Friday before Christmas still not fixed. GE is closed. The repairman and GE both lie and said it would be fixed before Christmas. Do not purchase anything GE. They do not stand behind their products. The products are poorly made and dont last. Ive had several dishwashers over the years. This is the first GE and it will be the last. You will have to wait over an hour for on hold to reach anyone and even then they just dont care. Save your money. Buy a didnt brand.

I bought the matching GE Microwave and Range four years ago. After three years of usage, the plastic on the handle melted and peeled, making it very uncomfortable to open the door. It was caused by heat from the GE range below. It took months to replace and cost almost $150.

Beware of GEs scam! My new house came with a GE microwave oven model JVM1630. It no longer heats food so I called GE repair. Heres basically what they told me: It is likely the magnetron tube and it is still under warranty, so no charge to replace it but I would have to pay $99.95 for the repairman to come to my home to diagnose the problem. If I decided I didnt want to repair the microwave, I was offered a $100 coupon toward a new one but it had to be a GE and it had to be bought on their website only. If I decided to go ahead with the repairs, the $99.95 would be deducted from the bill and I would only have to pay for additional parts and labor. I repeatedly asked for a ball-park labor charge so I could make an informed decision as to whether it was cost effective to have the repairman come out or just get a brand new one elsewhere. The person on the repair line hung up on me! I called back and I was told the same thing; that no one could tell me what the labor cost estimate might be. I asked to talk to a supervisor and same story. I didnt schedule a repair because I was taking a long trip and wouldnt be using the microwave anyway. When I returned from my trip, I called GE repair and again they wouldnt give me a ball park figure. Frustrated, I decided to have the repairman just come out and repair the darn thing and an appointment was scheduled for the next Monday. I had to rearrange a Monday day trip to Wednesday and set the repair appointment. On Monday, it was starting to get late in the afternoon, so I called to find out if the guy was on his way. A recording said my call was noted and I would be receiving a follow-up call. About 10 minutes later, Kim in dispatch called to tell me she had to reschedule the repairman to Wednesday. I explained I already had an appointment on Wednesday. which was already changed because it conflicted with the repairman coming to my home. She told me the repairman couldnt come because his truck wasnt safe to drive so that whole day was shot. The appointment was rescheduled for Wednesday and I had to again reschedule my other trip. When the guy finally showed up on Wednesday, he told me to put a glass of water in the microwave and start it. Ten seconds later, he declared it to be the magnetron tube. He was at my house about 10 minutes, just long enough to take my $99.95 credit card payment and to give me an estimate of $246.90 to repair the microwave which included the free magnetron tube, a $20 part plus tax and labor. The estimate had instructions on how to get the $100 coupon if I decided to buy a new GE microwave, which he said is what most people do. He didnt seem like he came prepared to repair the microwave at all. I was so frustrated and already out the $99.95, so I told him to go ahead and repair it. He said I should call repair to schedule him to come back to repair it! I told him to just repair it now and he said he didnt think he had a magnetron tube in his truck. I asked him if he would go to the truck and check! He did, and nope, no tube and he left.I think this is a great scam GE and maybe others have going. Its entrapment. They get you to accept a repairman to come to your home and charge you nearly $100 for it, but give you a coupon for $100 for a new one but it has to be a GE and can only be bought from their website where they can go as high as $500 or $600. By the way, I got on the website to find a replacement. My model had been discontinued and the only one in my price range was also a discontinued model. They charge $75 to come out to install it and another $30 to take away your old one. I called local appliance stores to see if I could unload my old microwave for parts and they all said the same thing: stay away from GE products.

Microwave counter top - On Oct. 15, 2010, I purchased JES1460 DNWW at Pacific Sales San Jose. Since then, two service calls on this microwave which replaced one that did not work. New sensor on service call 10-10-11. Today is 3-6-12, strong electrical smell practically knocks you out. I unplugged the unit. We always purchase GE appliances. No more, very poor quality. We are upset.

After a year and 1 day of use the microwave blew out and got in fire. Fortunately I was nearby and was able to extinguish the fire. I called the customer service that told me the warranty was over and all they can do is give me a discount on the purchase of another unit, and that I was on my own for the collateral damages due to the fire!

JVM1540 - We replaced the microwave that came with our home above the stove. When we took the old one out, the blower was not installed properly for ventless. We thought that had to be the reason it just stopped working. We felt sure it wasnt GEs fault as we have always trusted them for a quality product worth the price. WRONG! I cant help but wonder if Lowes knows they are selling a costly piece of junk! When our new one quit working, we replaced the fuse 3 times, now it says keyboard is shorted service required. And thanks to this site I am tossing this piece of junk without spending any more money. GE shame on you!

I have an above the range GE microwave oven, model no. JVM1750M1CC. It has been in service for about 9 years. About 6 months ago it stopped working with an F3 code. The code claims the control panel needs to be replaced. I found that the price of the control panel was over $100 and the service call was at least $100. A little shopping around and I found I can purchase a new oven for about the same price. As the control panel is located just above the largest burner where water is usually heated to a boil, it receives a lot of steam. I visited a local church second hand store and purchased a countertop microwave and used it while I found a good solution. I decided to let it dry out for a few days and lo and behold it worked again. Unfortunately it only worked for a few hours, sometimes a full day and then I needed to let it dry out some more. I purchased an extension cord with an on/off switch and hooked it up. Now I can stop the electricity without having to climb up on a chair to pull the plug. Once I was set up with the easy on/off switch I could easily reset it. After about a week of resetting, it got the message. It has been working properly for over two weeks now with no failures.

Very heavy to mount above a stove, not enough watts. The model I have is 900 watts, too many options for cooking different foods, not many parts are available to make a repair on any of the GE microwaves, I would not recommend purchasing a GE.

I purchased my GE profile microwave in 2010 when my kitchen was being redone. I picked it for its style and the GE reputation. So far after 9 years, I hope this wont jinx me, it has been a wise choice. I use it daily.

I purchased my GE Microwave about a year and a half ago. It has served me with flying colors till yesterday. To explain, I was boiling a small plastic pan of water for some rice. I have done this many times in the past. In the middle of the cooking cycle I heard a loud bang from the microwave. I stopped the cooking cycle and opened the door. To my surprise the glass turntable had shattered into several pieces. I cleaned out all the broken glass and tested the microwave. It seems to be working perfectly with the exception of the glass turntable. A new one was ordered. No further action is required. This is just an information for GE.

Updated on 06/28/2021: Nearly 8 months plus my mother waiting for dishwasher and now its the wrong one. Store where she bought it made a mistake. I didnt catch it till the dishwasher broke, She originally got the right machine but store marked it wrong on the invoice. Now on top of this the brand new dishwasher doesnt even work. It has a E4 code indicating a leak. Waiting over a week for serviceman. It always because of covid is the excuse for shabby service.Original review: I have never had such a problem in my life, first you have to phone then its either they put you on hold or transfer you to a voice mail. This is ok service until something serious happens then all of a sudden you dont get any call backs and stall tactics and simply dont listen. My mother bought expensive GE Profile dishwasher with 5 year bumper to bumper warranty that means nothing, I cant get through, tried to send form there no way to send it just a clear button??? Its supposed to be at least in contact within 48 hours to 72 hours. I have given them extra time due to Covid but I BEGINNING TO BELIEVE THAT IS JUST ANOTHER EXCUSE FOR THEIR TARDINESS. THE WARRANTY IS Excelsior guardian angel plan.

Bought a new GE microwave cafe series in May 2014. Within one month the handle which was not stainless steel started to peel and cut my wifes hand. GE sent a replacement new door for the unit that did not close. Then he had to transplant the handle from the new door to the old door. A month later the unit failed. A new replacement unit took 2 months to replace. It has worked 3-4 weeks and has also now totally failed. Our experience with GE CAFE microwave and GE service process is poor to miserable. I would not recommend this product or their service to anyone.

Microwave Model HVM1540LP1CS... This microwave was installed 6 years ago when I built my home. I live by myself and the microwave has only been used by me. I loved this microwave until suddenly it began to turn on by itself and I would often hear popping noises. I looked up reviews of this GE microwave and found that this is a frequent problem with GE microwaves. Fires were reported in a couple of reviews so I immediately unplugged mine, as a safety precaution. If this happens frequently with these microwaves, why isnt GE replacing the parts for the defective machines since they can be fire hazards?

The interior paint on the microwave is peeling causing there to be sparks in the interior of the microwave. The microwave interior paint is defective and should not have peeled. The microwave interior has metal showing which causes sparks.

We have a GE Profile Microwave (PNM1871SM3SS) that is only 3 years old and is reporting KEYPAD SHORTED - SERVICE MAY BE REQUIRED. We called GE service repair and told them the exact message. The service guy shows up and says all he has in his order is General other service needed and that he doesnt have the keypad panel. Gives us an estimate of $501 to repair it. Tells us a new one costs $400 and with a coupon he can give us it will be $100 less. We were charged $99 for this visit which basically lasted 10 minutes (way to go GE on making money off faulty devices you sell). The service-person also told us that the average life was 10 years for these, but this one crapped out in 3. He said if we get another GE microwave, it will fit right in there and that I can do it myself if I am handy but after reading all the reviews online, I am skeptical whether I should get a GE microwave again or not!

Good dishwasher for the price. Racks are well designed except utensil basket takes up lot of room. Given forks and knife rack at top, basket is not needed. Dishwasher flies at night.

I purchased the micro from Sears. This is the replacement for one that was provided by the builder. The G.E. now needs replacement. Will work for limited periods of time. I have used it more than my stove to cook chicken, beef and whole meals. I will be replacing it with a new G.E.. The current one has lasted more 10 years with very heavy use.

We were super excited to get this GE Profile Cafe dishwasher. Minus the brand, it was the exact design/style as the one my dad has which we love! First issue, dont have a name of a dish liquid if you cant use all of them. Cascade apparently makes different detergent styles for the smart dispense. Dishes were ridiculously dirty and the horrible thing is I couldnt find an answer why on GEs site, I had to go to a handyman site. That was about a month and a half ago. Today, I did the dishes and, of course, let it do its thing. I always have the heated dry on by the way. Well, dinner came and I grabbed some dishes out which were screaming hot and I had to use an oven mitt. I didnt think anything of it because sometimes Im a sissy about that. Well, its now 3 hrs later and I get up to the smell of burning plastic. My first thought was that the sippy cup straw fell on the heating unit. I did not, however, expect to open it and see the Tupperware melting, the silverware rack melting and the water bar to be melting to the heating unit and it being so hot that I have to use an oven mitt just to touch the freaking rack. Oh! And by the way, we bought this off Craigslist last year and it was brand new. It still had the casing around it from the store.

Bought a GE dishwasher that a service bulletin was generated by GE on a fault in their manufacturing. DD03-16 for reference. The door does not stay shut and continues to open. GE customer service suggested replacing hinges and brackets on the door. So I ordered the parts and changed them. It did not work. I called them back and they suggested purchasing and replacing additional parts. I called a local 3rd party and they provided the service bulletin and said that this is a problem in the design of these models. GE will not repair the problem. The cost has been shifted to me or they suggest buying a new dishwasher for only $150 over retail. They are hiding behind a warranty that expired, but the problem started at time zero when it was made. This is garbage and I have been without a working unit and continuing to argue with them over the repair or replacement cost. Call if you have this problem because they have identified it and have a solution that they will not tell you about.

We have had our GE dishwasher model GDT580SMF5ES for only 1 year and a half. As I was closing the door the hooks that attached the outer shell/panel to the door broke. Unfortunately we didnt purchase extended warranty so this will not be covered. We have had two technicians from our home insurance coming in but we are not sure yet if the policy will cover the repair. I just cannot believe this is happening as we have barely used this dishwasher as it is only my husband and myself. All I can say is dont buy GE.

Worst dishwasher ever. No matter all tried it just does NOT get all off dishes. Have to hand wash too! IS just not made to do the job. Just relying on GE reputation of the past! Made a mistake believing General Electric hype advertising. SAD.

I love the way the dishwasher is so quiet and cleans the dishes well. However, they are ALWAYS WET. A repairman came and told me that I could not expect the dishes to be dry on the light cycle with the POWER DRY. He told me I have to wash on the normal cycle. I did that and they are still wet. He came back out again and basically had no viable explanation. I have to have a dish towel in hand to dry the dishes as they come out of the dishwasher. I paid a lot of money for what I consider the piece of junk that is sitting in my kitchen. I will never again buy a GE PRODUCT.

Ive had an overall good experience with the dishwasher although sometimes I feel that you have to do too much prewashing and the dish wash cycle takes a really long time.

GE Triton XL dishwasher overheated for no reason and melted the inside components to the point they are scorched black. This dishwasher is worthless. There would have been a possible home fire if we were not at home at the time of incident.

I have been trying to get this dishwasher to work since April. I have had it serviced 2x and yesterday the board was replaced. Soon after the dishwasher started to say the same thing again. Press start and the cycle is paused and will start in 3-2-1. it does not start but repeats and beeps over and over. I have done everything in my power to get this rectified. It will run out of warranty in October and I havent been able to use it. As a consumer I am demanding a usable product that I spent my hard earned money on. Here is the model CDT875P4N2W2. I will go to any lengths to get some attention in this matter and I hope Consumer Affairs can contact GE Corporate for me.Dr. David ** Lewes Delaware

I purchased a dishwasher from GE 3 months ago and it broke, just stopped working. I called GE. After being on hold for an hour, they scheduled a repair call with At Bay Appliance, gave me a confirmation number and everything. AT BAY dispatch says they never received it and cannot schedule an appointment with me, I have to go through GE. I took the day off of work for this repair!I called GE again and was told to call Consumer Relations who apologized and scheduled a second call with AT BAY, apparently the only company who can repair in the SF Bay Area. Guess what? They say they never received the repair order and that I have to call GE. Again, I took a day off for this repair. What is this? Ive never experienced such poor service in my life.

Installed 07/06/2015 While I was asleep on 12/09/18 the oven appeared to start microwaving an empty oven on its own. When I came down 5 hours later the microwave had no power. I opened door and turntable had melted and glass had exploded. The ring under it was burnt and melted in one location. Top of cabinet on right side was hot. Then the internal circuit breaker restored itself and started some recovery process making odd noises sounded like the magnetron was trying to run since the top was getting hotter, after a minute the internal circuit breaker shut it down again. I then unplugged it. It appeared the magnetron started heating on its own and turntable did not rotate. All of the heat was concentrated at 12:00 edge of glass turntable. It also burnt the metal floor under that spot.