I bought my GE DISHWASHER many years ago. Only use once in a while because there are just 2 of us in the house and it takes too long to fill it, but when I do use it it work fine.

I purchased a this GE Model CDT845P2NS1 on Oct 2, 2019 and the unit was received Oct 23, 2019. I installed the unit approx. 4 days after receipt and dishwasher functioned well until November 10th, 2020 when the unit failed to pump out the water. I contacted GE Service (MabeService) and was advised that the unit was not under warranty and as such I should contact a GE Canada authorized service centre.After several attempts to get someone to come to our location at Sharbot Lake we got hold of Capital Appliance Repair in Ottawa. They were not able to send a technician until November 18th. After diagnosing the problem the technician advised we needed a main control board and would have to order one and then come back to do the install of the control board. It is now February 21st 3 months after the visit and I’m being told that the part is backordered and they have no idea when it will become available. I’m extremely unhappy when you spend over $7,000.00 for a GE CAFÉ gas stove, Microwave, Refrigerator and dishwasher to find out you cannot get parts in a timely manner. As a customer of GE Canada I have had no help is solving my problem. It is not acceptable to have a 1 year old dishwasher that has failed, much less waiting for repair that has taken over 90 days to get repaired. DO NOT BUY!

First impression was good but then went use it and found the basket was shallow. This was not a cheap one and was very quiet when running but multi loads have to be run. Overall the looks are good and the mechanics all are holding up fine. The smaller inside is the killer for me.

Periodically my GE Profile Dishwasher will not clean well. On every occasion it is due to clogging of spray ports on the upper and/or lower spray arms. Removing the blockages is nigh-on impossible as it is often not possible to extract the blockage from the outside and its not at all possible to flush the blockage back down the arm to extract it at the centre. All that is required is a bit of forethought and the creation of some access to the arm. I was frankly surprised to not be able to find a replacement arm as the suggested solution to this problem, the additional part revenue being part of GEs the business model. There are a number of other design issues with the assembly at the bottom that make me think it was done by an intern and nobody checked her work at the end of summer break before it went into production.

My GE Profile Dishwasher was serviced 2 years ago for a faulty electronic control pad. It made starting the dishwasher a complete gamble, you never knew when it would actually turn on. I paid a couple hundred dollars to fix this problem 2 years ago and of course it has stopped working once again. So frustrating! GE decides to replace one bad part for another bad part. I then asked for the service call to be covered since it was obviously the same problem but they refused. So, GE am I to keep paying $89 for service fees so that you can keep replacing one faulty part for another? STAND BY YOUR PRODUCT!

Our microwave is spacious, simple to use and dependable. This is about the fifth microwave I have had. The others only lasted about 6 months. My current microwave is about 5 years old, despite the fact that some of my previous ones were also GE.

Purchased a GE Profile (oven and microwave unit) for over $3000.00 seven years ago. The protective coating on the interior of the microwave completely wore off down to the metal under the wheels of the turntable. GE calls this minor chipping (which it is not), advises to stop using the product, and offers a $100.00 off a new GE unit because they cannot fix it. The product should be recalled, just like Honda did when their Pilots were peeling.

GE Dishwasher GDF520PGJBB - GE has the worst dish washer machines you can ever buy. In fact never buy a GE dishwasher in general. Maybe, GE makes good refrigerators but not dish washers. We bought this from Home Depot and after 6 months it collapsed: Pump broken, soap dispenser broken, panel doesnt work. We had before a Maytag and we used it for over 20 years without any issues. In addition, GE has the worst customer service you can imagine. They are robots, repeat the same thing with a very annoying tone, and are not able to solve a single issue. We were even harassed by GE manager Evan or Aven, useless man, from customer relation who enjoyed seeing how much frustrated we were. This was the only GE appliance we have in our house, and after this unpleasant experience with GE will NEVER buy any GE appliance, even if it was free. GE refused to fix our machine under the pretext that its not installed on Ply Wood. We didnt install the machine ourselves but professional technicians from Home Depot and they also refuse to put PlyWood under the machine as its not a requirement. They do it every day, but looks like GE have Lazy technicians.

I give it stars for value because an extra step is needed to set cooking time. Most microwaves do not require pressing a cook time key before selecting # of seconds. Other than that, microwave is first-rate and very dependable. We use it several times a day for 1.5 years now with no problems.

Microwave lasted 6 months, very light duty, burnt metal smell. Purchased from Walmart, they told us to contact GE. All GE could offer is a Good Will certificate which means, we have to go buy another GE microwave up to $155 in value. We pay taxes, shipping etc. Not really a customer-centric return policy for a lousy designed product made from cheap components in Asia. These microwaves are a piece of junk. This isnt the only complaint about this model of microwave. Others are experiencing the same problem all within the past 6 months. From March 2018 thru August. Stay away from these microwaves.

GE Model JVM1540LM5CS - Fire inside microwave while making popcorn. Top center piece, inside microwave, caught on fire. Was able to quickly contain the fire to the circular plastic cover which I removed. Called GE customer relations for service. The service technician that came to repair our microwave said he had just come from a customer with the same problem. Sounds like GE should take a close look at the plastic piece that catches fire and see about replacing it with one that wont burn.

Ive had an overall good experience with the dishwasher although sometimes I feel that you have to do too much prewashing and the dish wash cycle takes a really long time.

Soon after getting our new Cafe Microwave CVM2072SM3SS the control panel died. I called GE and power cycling got it going again. This is an over the stove microwave, so we were also told by GE not to use the right front burner without the fan on boost. The problem persisted from time to time and steadily got worse over our 5 years of ownership. Reading the internet this was a common problem known to GE but they took no action to contact owners. The panel is now dead and my only option, having tried the fixes on Youtube, is to invest money starting at $108 for an inspection or buy a new Microwave. My entire experience with this product has been a big disappointment as I also own a GE Cafe range, fridge, and dishwasher.

We purchased a GE Profile dishwasher because our old one was recalled for fire hazard and we were offered a rebate on a new one, and told there was no fix for the old one. On the new Profile dishwasher, the water inlet valve stuck open and flooded our home. Tech said we may as well have had a hose on full blast all night. Word to the wise, do not turn your dishwasher on and go to bed or leave the house! 7 1/2 hours later we woke to a completely flooded downstairs. When we were researching whether or not there were other complaints on that model dishwasher, we noticed there had been a recall for fire hazard ON THE NEW DISHWASHER! Since this is located right under our bed, we were fortunate though not happy about the flood! We have exceeded the 40K mark in damages and the assessments and estimates are still coming in. We will never own another GE product, though we recently purchased a stove with a double oven which is thus far wonderful. GE has also recently been purchased by Electrolux. We chose a Bosch for our new dishwasher.

We have a full size counter top GE microwave. It is about 3 years old and there have been no problems. Our last microwave was also a GE and it lasted about 15 years before it started to suffer from occasional electrical arcing inside, while in use. We simply stopped using it and after reviewing all models, chose to buy another GE and it has been great. We have an over the range micro at our summer home - a Frigidaire and not as good. Our research shows it will likely fail long before the GE.

I have had a few cheap microwaves but at this point in my life I wanted to buy a good quality microwave that would last. Well I bought a 200 dollar GE microwave in February. 3 months later it went out on me. I did hard and soft reset numerous times with no success. They offered me a discounted check to replace it and it would take 4-6s weeks to receive. Instead we returned to place of purchase and they gave us a floor model to replace it. All was well for 2 months when lo and behold this one started doing the same thing. No amount of resetting would make it run. It went out cooking corn on the cob. Why is this so hard to keep running? Their response this time was a goodwill rebate certificate to purchase only a GE microwave. Why in heavens name would I want another one? It only lasts a couple of months and who is to say the 3rd replacement will not be the same.

I was washing the inside of my microwave and noticed that paint was peeling off the top. It looked like paper. Reading the other comments on the same problem I knew it would do any good to contact GE. GE products have always been inferior to other brands in the market.

We purchased a GE dishwasher model GDF 510 in December 2012. We have had three service calls with a fourth one recommended. The first complaint was that dishes were not dry at the end of the cycle. After service calls to replace a faulty heater and install two computer upgrades, the silverware still is not dry. Finally after about 45 minutes into the cycle, it leaks onto the floor. GEs answer is to send another service technician. No thank you! They can have their dishwasher back.

I am rating my over the counter GE microwave model no. JVM3160RFSS. Ive had it for over 2 years and its still performing well. Pros: Solid feel, sturdy door mechanism, easy to clean interior, attractive design, fairly quiet, adequate lighting inside, reasonable price, fan works okay for moderate smoke, short reheating times for lighter fare, cooks frozen foods quickly. The integrity of the interior is good with no chipping or cracking. Cons: Fan is inadequate for heavy smoke if searing beef, hot and cold spots while reheating heavier foods such as mashed potatoes or casseroles, controls are hard to see in dim or moderate light. A suggestion to GE would be to make microwaves with optional backlit buttons to see at nighttime or in dim lighting. I like that GE manufactures most of their microwaves in the United States.

We bought a brand new GE kitchen. We put all GE in the new kitchen. The hood/microwave/convection oven broke in 9 months. We had service out, and they wanted the same amount we paid for it to repair it. My husband is an engineer and he got it to limp along. Then in September, it broke and cracked up. All the control panel cracked and broke. It does not work. We called GE. They said to get a replacement. We went to Sears and bought a similar unit as the original has been discontinued. We were assured of a credit towards the new one. A credit would not be issued. Gary ** has continually called my home but not my cell. He reached me today in school, a Special Ed behavioral unit, and started yelling at me over the phone. He said that I did not provide serial numbers. I have many times. He said there is no record of my complaint. I have called, emailed and written at least 3 times providing all information. We just want a credit for the original unit. We have provided sales slips, etc. Please help.

I purchased a full suite of GE Monogram Appliances about 5 years ago. All are fine except the microwave which was made in China. The back is rusting out, the inside is chipping at the door and moisture builds up in the door window. This progressive deterioration has taken place over the past 5 years. I paid $420 for the microwave plus $226 for the trim kit. Now, all GE wants to do is sell me a new unit and a new trim kit (will not fit old trim kit). I paid approximately $20,000 for the entire group. I bought GE because I trusted the name. Im stuck with GE if I want to match the remaining appliances. There are only two people living in this house so there is only minimal usage. To further complicate things, there is no serial number on the tag.

I was advised to replace the timer #WD21X10059. I replaced the timer and it still doesnt fill water. I purchased this 2000 Hallmark Park model and the seller said the dishwasher has never worked. The model #GSS1800Z01 does not add water when turned on. The water line has been checked and is OK. Is there a service bulletin on this unit?

We purchased our GE dishwasher in September 2014. In December 2014 the dishwasher started to make a loud grinding noise. I contacted GE and a repair man was sent promptly to do the repair. Upon arrival and looking at the dishwasher he advised me that it was the motor. He then stated that he would order the parts and also stated that he did not have the correct tool to remove the motor and has not had one since they have changed the manufacturing process. At this time I am still waiting for the parts and I have contacted GE numerous times to find that the parts were either on back order or had been shipped out. I am still waiting for the parts and the repairs to be done. The estimated date of the parts to arrive is January 29th. At that time I will have been without a dishwasher for a month that I have just purchased.

I purchased this dishwasher on April 2018 and from the beginning was not working well. I called a technician about 2 months ago, came with the computer and told me it is working fine, but my dishes are never well cleaned. Anyway on Nov 27, 2018 the water started coming out from my tiles and I didnt understand why? I kept drying and it kept dripping. I was so worried and called a handyman. He told me it is the dishwasher dripping water. All my cabinets, my tiles are wet inside. I have called and report it and today a technician was coming to repair it (which I will not accept.) I want a peace of mind. I need a new working dishwasher. Today, the technician was supposed to call me before arriving and I was 5 minutes away and left. Now, your customer service reps are telling me to wait till Tuesday. I am having guests and my house is a mess, I have the dishwasher in the middle of my kitchen, everything is stinking to humidity and all happens because of this BAD PRODUCT. I want this trash to be exchange as soon as possible.

I have a 2011 GE Model # JES1456BJ05 microwave and it has been gently used and kept clean. Upon cleaning today I noticed that the top of the inside is blistering and peeling off. Surely this is not safe as it could fall into food, plus they should make them to stand heat, after all this is why they are made for heating things. I called GE who informed me that there is no recall on them so I am pretty much stuck to go out to buy a new one with no help from them. I now read that this has happened to people before. Lesson learned never purchase a GE microwave as they do not stand behind their products when a manufacturing problem develops if you are the first one to call, and beware and ready to buy a new one every 2-3 years. This is all they are made to last!!!!!

I have a General Electric HVM1540DN1WW over the stove microwave that I have had. This month will be a year and a half. The oven stopped heating so being a DIY person, I pulled the oven out and took it to my workshop to see if it was something I could repair. Inside the front panel was a very helpful schematic of the whole oven. Using the troubleshooting step listed on the paper, I found that the Magnetron tube had gone out. So I went to my owners manual and found that the tube had a four-year warranty on it so I called General Electric consumer relations to have the part replaced. First I had to fight with them because they said it was only covered for a year. After about an hour and a half on the phone and giving her the publication number on the manual, she agreed that it was indeed covered for four years. So she said that she would replace the part and she would even send a technician out to install it at no charge. I was very happy at this point. She said that she would ship the part to me next day with UPS and the tech would be out the following day to replace it. So far so good, till the next day when the part did not arrive. I called back in to General Electric consumer relations and spoke with a man this time and he told me that she had canceled the order that is why I did not receive it, and he couldnt see why. So he looked at the comments she had made the day before and did see that she said she would replace it and send a tech. The tech was supposed to be here the next day and I had no part for him to install. The man said he would place the order and have it shipped to me by the next day no later than 10 a.m. and the tech would be here between 1 to 5 p.m. Great! Until the next day and again no part when they said it would be there. Again with the call only to find out that it was scheduled to arrive next day guaranteed by 7 p.m. The tech is supposed to be there with in the next few hours and I wouldnt have the part. I called Fed-Ex and sweet-talked the lady into getting a hold of her driver to see if she could get to me ASAP. Bingo, next thing you know I have the part, the tech calls and the part is replaced. Oh boy, the big gaping hole above my stove is finally going to be filled once again. (I promise I am coming to the end.) After reinstalling the oven, I found out that it was taking longer to heat than when I got it, and it has a brand new Magnetron in it.Again with the call to General Electric consumer relations to set up another tech to come out and check it out. So the following day, the same tech arrives and puts a cup of just barely cool water in it and puts it in for 30 seconds, pulls the water out and says it is working just like it is supposed to and leaves. Well, again I called General Electric consumer relations to let them know what has transpired, but this time I asked to speak with someone higher up the food chain. I then spoke to a lady and she said that she would set up another tech to come out and check it out, and if it resulted in the same way that she would replace the unit with a new one. The following day, the same tech calls me and said that the oven is working the best that it could so I should call back to consumer relations as he did and set it up for a new one to be sent in its place. So I called once again and was not able to speak with the same lady and the only thing she could do is send me a voucher for $250 laying around for a new oven, but I would have to purchase one and send the voucher in with the receipt to get a refund. I told her that I did not have a spare $250 dollars around to go buy a new oven and then wait for the refund to get to me. So I asked that she have the lady that said she would replace it to call me back to straighten this problem out. Finally the following week, the lady calls me back and said, This is the best that I can do, due to me voiding the warranty. I asked, What? She said that the tech that spoke with me said that because I had hard wired in the unit to the house wiring, it was receiving low voltage so she couldnt do any better than that. I told her that was the most asinine comment I have ever heard coming from a field tech and asked her whether he went to a school backyard Techs-r-Us. I asked if she would have the tech call me to explain. I also gave her some friendly advice that she should not use that comment to anyone else for fear of someone laughing at her. We agreed to have the voucher sent if that was the best she could do. I will not buy another GE appliance again! I have purposely not mentioned anyones name because it was the experience, not the person that I spoke with.

I purchased a new GE over the oven microwave to replace a 10-year old Spacemaker unit. After three weeks of use with no issues, the unit overheated excessively during a normal use. The heat was so intense that the pegs that hold the racks melted causing a severe burn on my sons thumb. I unplugged the unit fearing further injuries and/or fire. Are GE products manufactured poorly or did I get a lemon? Who knows? Anyone else have a similar issue? I am still waiting for GE to respond.

We purchased a new home with a GE Profile dishwasher installed. Since the day we had it, we have never been satisfied with the cleanliness of the dishes. They frequently come out covered in food and must be rewashed. We now routinely prewash everything in the sink and we always use the cookware setting to wash everything. Despite this, we still have to re-run loads because they are not clean.I am convinced that there is a design error with our dishwasher, because the top dish shelf obstructs the door of the soap compartment and prevents it from fully opening. After a load has run, you can still see leftover soap dried and crusted in the soap container. If the dishwasher cannot even wash the soap out of the soap compartment, no wonder our dishes are not clean.

My GE model JEB1095BB04 microwave/convection oven is 6 years old and the magnatron has failed twice. The first time, GE said they would replace the part free of charge, but I had to pay for the service call, which I did and it cost me $212.00. Now, the part has failed again, the second time in 2 years, and GE basically said you lose. A rep from GE told me that they only guarantee their products for 1 year. There is no doubt in my mind that all GE products are garbage and I would strongly discourage anyone from buying them. I will gladly take my GE microwave, smash it into pieces and replace it with a KitchenAid appliance, which is backed by a reputable company.

GE Profile GLD4408RBB: Bought this dishwasher at Home Depot 2010 for our FL condo. We visit there periodically, dont rent out. We have used this dishwasher probably 50 times since buying. It never wash dishes well, leaving residue and we do clean them first. Now it doesnt drain; seems like pump not working. Its only five years old and hardly used. Its not worth having a repairman for labor and cost of parts. Very disappointed with GE product and wont buy another one.

I do not remember what I paid for this microwave, but my budget was low, and the value I got is good for the money. Ive never had any trouble with this oven, and its 5 years old. Its a good size and cooks evenly.

My husband and I enjoyed our 1980s White GE Microwave and Stove/oven. But, after 15-20 years with the same appliances, we finally saved up for upgrades and purchased a new Stainless Steel (mid-range priced) GE Microwave and stove/Oven. I cannot begin to describe our disappointment. The Microwave is above our Stove/oven. Our old microwave had two powerful lights underneath it - one on each side. This microwave provides one small, weak light that does no good any time of day. Why would GE go from two great lights to one middle useless one? Also, the faint white numbers on the front keypad of the microwave are barely visible during the day - forget about seeing this when the light is not perfect. I foolishly assumed these numbers would be backlit on a black background. Onto the Stove/oven. The temperature is not accurate but that is something we can deal with. After the oven is pre-heated, the assigned temperature stays on the display pad - NOT the actual time. Who cares about the temperature you set the oven to - dont we all need to know when to check or take out our food? Our last oven always showed the time. We did not join the Stainless Steel bandwagon 10-15 years ago when others did - which we thought would be good for GE to get some kinks out. I Guess we should have waited 10 more. Proper lighting on your Microwave and The time on your stove/oven while cooking are not too much to ask for when we just dropped at least 2-thousand dollars!!!!!

About a year and a half ago, I bought a GE Profile dishwasher from a very reputable local dealer. Within 3 months, the digital control panel failed. Because it was still under warranty, the dealer replaced the panel. It failed again. This time they made other adjustments, it continued to fail. Finally GE suggested that the dealer replace the entire door panel, which they did. It took the repairman a couple of hours to do so. Still didnt work. Finally GE declared the machine non repairable and replaced it. Unfortunately the men who replaced the dishwasher didnt install quite correctly because it leaks. I keep a plastic container under the front left corner to collect the water every time the dishwasher runs.But the story doesnt end there. This machine and the first one both include a sensor that apparently check for objects that obstruct the spray arms. I dont know because theres nothing that tells me why the machine is beeping when I attempt to start it. I check the spray arms, move dishes, try to start it again and still get the beeper. I have done this over and over and over again and still it beeps. I have essentially emptied the dishwasher and it still beeps. When it does run, I have to use the boost temp. option and the longest cycle available to get dishes, and I mean dishes, even passably clean. Forget pots and pans, or casseroles. So, if you own a GE dishwasher, I hope that you have the old fashioned dishpan and dryer rack handy. Bottom line, it doesnt clean well, leaks, and beeps every single time I try to start it. Buy something else.

My dishwasher does an excellent job - its a bit slow, but it gets the job done reliably. It is probably slow only because its old and somewhat tired...It does a great job cleaning off remains on dishes, which is not always the case. It doesnt fail me.

Model JVM1740DP1BB - GE Microwave - complaining since November 2014. Great microwave UNTIL the inside ceiling bubbled and began to flake off in various locations. A service tech that visited our home advised us to call GE and advise them of a potentially hazardous situation. The GE rep offered to sell us a new microwave but only stated that we were out of warranty, although this is clearly a manufacturers defect! She proceeded to tell us the lining was perfectly safe but maybe we shouldnt operate it. I have written GE management to see if they will assist in replacing the defective unit; GE is the reason we purchased it to begin with (but it may be the reason never to purchase one again).

When we purchased our home it came with GE appliances which was covered under a one-year warranty. My microwave has been broken for nearly 3 months. It is almost impossible to get a service tech to come out immediately. GE customer service is the worst I have ever dealt with. They are unprofessional and unreliable. Most of all uneducated about their job. If I could return all of the items in my house that were made by GE back to the seller I would in a heartbeat. The Appliances are poorly made and the customer service is too difficult to deal with it. It’s not worth the money or the Headache... Stay away from GE appliances.

Dishwasher is 3 months old and today is the first time it has worked! GE has sent repair techs 3 times and finally today the unit was temporarily repaired with electrical tape attached to the brand new door latch. The door latch is cheap plastic and has a manufacturer design defect of being too small to properly engage the unit when the door closes, thus not allowing the cycles to start just a series of beeps. No other manufacturer uses a cheap plastic door latch designed like this but GE! Piece of crap, dont buy it!

In late March, we placed a service call under GEs one year warranty. The outcome - a gasket repair. Within a week or two, the door began to drip from both the right/left bottom. With having three teens, I figured someone opened the door and released some water. Well, that just wasnt the cause. Shortly over the next few days, the leak was consistent and I placed a service call to GE on 4/19. The customer representative offered, instead of a service call, to order some panels that fit it the bottom of the dishwasher. I stated clearly that our one year warranty was up on 4/25 and if this does not work, would GE address the issue with a service call? Answer was yes. Within a few weeks, I began to worry when I did not receive the panels. A call to GE was made; however, no documentation was noted of the call made on 4/19. However, GE stated the information might be in parts department, but regardless now, that call was made after one year warranty, extended warranty would fix the issue. Long story short, the extended warranty states problem initiated under GE and GE states the extended warranty is responsible because the call was made outside the one year warranty. I expressed that GE never fulfilled responsibility as GE did not even notify us that panels were not available for our unit. In the meantime, I am the one out of a working dishwasher. Now I know $539 may not be a lot to invest, but we feel the loss. The frustration and lack of responsibility to correct the repair is just beyond me. GE is responsible. Oh and did I share that lack of communication with GE is horrible? A promised call within 12-24 hours just doesnt happen. Again, I know most would say its not worth the frustration, but it makes me sad that GE and Assurant Warranty company can get away with what I know is wrong. Weve learned from this ordeal. No more GE products in our household.

Adora Microwave - door falling apart: This microwave is supposed to be installed above a range. The materials are not suited to this. The plastic door has disintegrated. We have got through 2 handles. I took the 2nd one off to replace it and the plastic that holds the glass in place just disintegrated onto the floor along with much other plastic parts. Why is the door plastic in the first place if they cannot make it from a heatproof material? Only 4 years old and we are going to have to junk it. When the first handle failed under warranty GE said that it was not covered as it is a plastic part! They finally covered it after a long conversation.

I purchased my GE Microwave about a year and a half ago. It has served me with flying colors till yesterday. To explain, I was boiling a small plastic pan of water for some rice. I have done this many times in the past. In the middle of the cooking cycle I heard a loud bang from the microwave. I stopped the cooking cycle and opened the door. To my surprise the glass turntable had shattered into several pieces. I cleaned out all the broken glass and tested the microwave. It seems to be working perfectly with the exception of the glass turntable. A new one was ordered. No further action is required. This is just an information for GE.

We got the GE cafe series appliances with our house. We just completed 16 months in our new house and the microwave stopped working. We had to call the GE cafe person to troubleshoot the problem. He charged us $80 (without even touching the microwave) and said we will have to spend $450 more to fix it. This is such a horrible customer experience. I had a $40 microwave in my old apartment which lasted for 4 years without a single problem. I am definitely not paying $450 for a useless microwave. But now I am worried about remaining appliances I have from GE. I understand that you would say you cant do anything as the appliances are not in warranty anymore. But if you really care about your customers, you should start looking into this and fix it. I am very very disappointed and I am not letting this go. I expect someone from GE to help us to get this fixed. Thanks for your patience to read this outburst of a disappointed customer.

My microwave was purchased 2.13, costing about $500. The panel shorts and I paid for one GE visit, $150. And it happened again. My friend was here and said hers does the same thing. She has a neighbor with the same problem. I researched online and learned quite a bit about this machine. I found out that the panel shorts when youre cooking under it, and steam/heat rises into the machine. Makes the panel short. Im now demanding that GE return $150 service fee that I paid before I found out that its a defective machine. And this machine has to be replaced with a model that allows cooking with vents on. If GE does not do the right thing, I will make it a life goal that no one buy their products. Mark my words. Im this angry because I called customer service this week and was told that theyll give me a new panel but I have to pay for the labor and no refund for the $150 and no replacement microwave. This was insulting. Shame on GE.

Needed to replace handle. Silver covering started to peel and actually got a splinter. Cheap plastic underneath covering. Called GE and while they did send out a replacement, I had to pay to have it installed. Instructions on internet were not helpful! Bill to replace was $142. Ouch. GE rep said they did not have prior complaints. I later Googled it and saw 1000 complaints!!!

June 18, 2018 GE Spacesaver Microwave in use when there was a loud pop, heavy smoke boiled out of the unit and strong smells of wires burning was noted. On fixed income now what do I do? Understand my microwave has been reviewed by ConsumerAffairs for the same issue in the past. Whatever became of their investigation?

Almost 2 years ago and right from the start this dishwasher did not clean. Numerous times they had people come out and supposedly fixed it. Ive had different suggestions as to what to do. 1. Turn on the hot water tap and make sure its hot. 2. Use various different cleaning solutions on top of the dishwasher soap. 3. Use loose detergent.4. Throw at the bottom of the washer.One of the arms keeps falling down. And the last time I was told I could return it and get a deal on a better machine. I am now left with hand washing every item that goes into it unless I want gritty glasses, dishes and silverware. I bought this at Home Depot. I will never buy any products such as this from them nor will I ever buy another GE product.

Seems to be a lot of wasted space in this GE dishwasher. If it had a 3rd rack then I would rate it higher. The back has additional sprayers, but the sides do NOT. I would think that having sprayers all the way around would help with sanitation.

The dishwasher is poor quality. Top is thin, top dish rack has trouble with tall glasses. Bottom rack doesnt slide in and out well. The power cord and water cords are too short. They are 2 ft shorter than our previous model dishwasher. Top was loose when delivered and had the wrong screw in one of the holes. The hose and cords are difficult to hook up because they are so short. We cant fit as many dishes in as our previous model of the same size and the unbiased reviewers are saying its washing quality is poor. We havent had it long and hate it. Home Depot wont take returns on portable dishwashers though. Out lots of money on this. This GE is thin plastic trash that costs lots of money with no return.

My microwave on the inside paint start peeling off. I have this appliance 2 years, it has slowly been peeling since that time and now it has completely peeled and rusted on the inside. This WAS a gift. The outside looks great, the inside is so bad. The serial # is LT914637B model JES1451DN1BB manufactured in 2010, Made in Malaysia. Be Louisville ky 40225. Does the united States make anything except make us pay taxes. This is a piece of mess. The last 2 years my husband he suffered with LLC. Now I got to deal with this. Poor workmanship. I want GE to give me my money for the MW or total replace it. Rate 0.

Absolutely silent! Several features and cycles such as crystal, normal, pots and pans and drying options such as air dry or heat dry. Standard size dishwasher. The key is in the loader. Stainless steel with no handle or anything plastic. Flush. Stainless interior as well. It did have a food disposal but to avoid smells since we start the dishwasher only twice a week, we rinsed off our dishes. Another important element we learned from the previous dishwasher is to use the heat dry if you want your load to be dry with as little puddles of water as possible.

My GE microwave oven died after 4 years. And my GE washer died after 5 years. Never ever buy a GE appliance. The market agrees, because their quality issues might be the reason the company has not been able to sell their appliance division for several years now.

Our GE dishwasher cost $1,000. Reasons for not buying GE. 1. DOES NOT CLEAN DISHES. 2. Latch doesnt catch. 3. Rubber strip comes out. 4. GE customer service is useless. 5. Interior valve broke. Everyone w/ this model has same problems.

Of course, I rinse my dishes, but Ive had few incidences of dishes coming out dirty. Hot start, start (long wash), short wash, rinse only and plate warmer. The interior is set up well with a good variety of spaces. I would say its a normal-sized household dishwasher, not compact, with approximately a 24 width, 24 depth and height. White with gray lettering; four buttons and one dial. Simple design that is easy to understand and operate. The run-time of this dishwasher is quite long, and it is very loud.

After only 4 hours of installation, the microwave turned on and the fan and light came on. It was not cooking anything. Inside of microwave was hot and I could smell a burnt electronics smell. I unplugged it, waited a few minutes, and when I plugged it in, it started up again. The LCD screen was scrambled, all lit up. Opening the door stopped the unit, but it started again when I plugged it in.

I live in a condominium building with approximately 105 units. We all had the same GE microwave installed in our units approximately five years ago (contractor-installed). I sent out a mass email to all of the owners to ask if they were having the same problems I was having my microwave, which was the touch panel will not accept commands. I received approximately 15 complaints from various homeowners with the same complaint.When I called GE to tell them the problem I was having with my microwave, they told me a technician would have to come out and diagnose the problem. The service call would be $99.95, and at that time the technician would let me know what the problem was and tell me the charge for the replacement part and labor cost. I told GE Customer Service that there were many people in my condo building who were having the same problem and I wanted to know why each homeowner should have to pay the initial $99.95 service call fee? The response was, That is our policy. To placate me, GE customer service said they would charge me the initial fee but I would receive a 25% discount for parts and labor.In the meantime, two or three other homeowners made service call appointments for their microwave oven with GE. One homeowner was given a fee for parts and labor, which would have been only slightly less than buying a new microwave and another homeowner was not given a labor cost. In both cases, the homeowners did not go forth with their repairs, because buying a new microwave was more cost effective.I want Consumer Affairs to know GE grossly mishandled this malfunction issue amongst a group of homeowners who own the same microwave. Secondly, I realize the microwave ovens are five years old, but GE should have some record regarding failing parts along with the life cycle of this product. Lastly, I want GE to be held accountable for not telling consumers a repair cost for certain issues. There should be a cost per hour, not cost per broken item.I kept records of all correspondence amongst the homeowners of my condominium building, so I will be of great assistance if you need further help from me. Product malfunction is a GE Profile Spacemaker 2.0 Model # JVM2070SK02.

I bought this Microwave JVM3160 on December 2016, after six month the handle door broke but it was replaced as part of the warranty. By January 2018 (no more Warranty) it began tripping the circuit breaker. I change the power source for a dedicate circuit only for the microwave 20 AMP. The microwave blew its own fuse. I replaced its fuse. Then it blew the 20 AMP circuit breaker. That was enough. This microwave went to the garbage after 1 year and 2 month of use.

My dishwasher is a GE Profile. It is as quiet as a Bosch we had in another home we had but it must cost half as much. We have it 8 years now- no problems. Never had a service call or anything wrong with it. It owes us nothing.

My GE Profile Spacesaver XL 1800 microwaves megatron went out. It is still under warranty, but GE refuses to send me the new megatron because they demand that their service company needs to install it. Estimate is $300 for installation. I had a local appliance repair shop look at it and they will install for $80. GE refuses to ship to them or me and state that their legal department has restricted sending to the customer or unauthorized repair shops. So I am being blackmailed for $300 in order to get the megatron replaced under warranty.

The GE repairman just left. It wasnt the coil that was flaking, it was the eco dish washing detergent I was using. The detergent wasnt dissolving, it was clogging up the jets and burning on the coil. What I was seeing was black burned detergent flakes. The repairman gave me citric acid to use to clean out the clogs (for free). He also didnt charge me for the visit, even though it was my fault. He also told me to get the water in my sink really hot before I start the dishwasher. I am very impressed with his service!

This updated version came with this house. I am very happy with my dishwasher, it is very quiet and is the top of the line. I love my refrigerator/freezer by the same company too.

We bought the GE dishwasher from Lowes 3 years ago and have had it serviced 3 times! The water pump went the first year and now the drain pump! Love the coloring Slate but very poor quality. Will not purchase GE products again.

I had to place a new order for a trim kit for my new microwave oven since the original one did not fit. I was told it would be 5 days when I placed the order, then it was backordered for 5 days, then 7 more days and now 3 more days. When will I receive the product that I have paid for 3 weeks ago?

Dishwasher lasted just little over a year when it broke down first time. Power switch made out soft plastic jammed up. Next cheaply made door close switch cracked. Part prices are average price. Because poor quality, I predict replacing this within 3-5 years.

Just purchased a home with GE Appliances. Dishwasher suddenly wont start and showing 1H code. Nothing in the user manual that explains what this means. Called customer support. After they requested unnecessary personal information (like email address, physical address, etc.), I was finally able to ask what this code meant. She went straight to, We are unable to provide that information over the phone. We have to send one of our service technicians out to your home. She refused to tell me what the code meant, and instantly wanted to charge me for tech visit. I hung up. Then I googled it, and found out right away that it meant the start was paused/delayed for 1 hour. I had hit the delay button by mistake. This was not specified in the manual under Delay Start, nor was customer support trained or willing to provide the answer to such a simple question. GE Support is just a Scam.

I wasted my whole day waiting for GE Technician to come. Nobody called me to let me know that they are not coming. I have to call them only for a Mr. ** to tell me that they had rescheduled the appointment for another one week without notifying me. Good job that GE APPLIANCES are doing. You remember the so called TOO BIG TO FAIL? It means, they can do whatever they want at whatever time or day they want. I dont have a vent in my house and that means I cant use the stove. Is this ridiculous or I am missing something here? Is it TOO BIG TO FAIL? Yes, I forgot that. I will be staying in a house with a new GE APPLIANCE that has not been working for the last one week and have to wait for another week. Mind you, this Appliance has been used only for barely a month. Is there anybody out there who is facing the same problem or its just me. If there is nobody going through the same experience, an excuse like there are no Technicians available to come to your place and do the job. If there is anybody out there who has trust in GE appliances like I did or even thinking of getting one. Be aware that you will be through what I am going through and there will be no technician available for another two weeks. Be ready to wait for they will reschedule your appointment without letting you know, why? Because theyre TOO BIG TO FAIL. What will you do? Wait until they decide to come, if theres a technician available. I just realized that GE means GO ELSEWHERE. Thanks GE for the good job.

I got a GE cafe two years ago, all the matching appliances. A few weeks ago, we heard beeping in the middle of the night. ow every night at two am we get a message on the panel with annoying beeping. This weekend, we went out of town and when we returned the microwave was and had been on for a very long time. It doesnt take a genius to figure out that our house could burnt to the ground while we were gone! Thank God it didnt! Not to mention. my dishwasher does not clean! It takes 3 runs to wash.

We have not had any issues with our microwave. It is relatively easy to operate (how difficult can it be, right?). Overall, we are pleased with our microwave. The microwave was already installed when we purchased our home, so I cannot speak to whether or not it is worth the price.

GE Stainless Steel Profile Dishwasher - My dishwasher is about 5 years old. Two years ago, we noticed that the gaskets, both around the tub and on the bottom of the door, were becoming gummy and rippling. We were hoping to make it another couple of years before buying a new dishwasher, but a couple of week ago, the top arm fell off because the gasket was so degraded. We ordered the appropriate parts and were only able to replace the top-arm gasket and the tub gasket. We had to call an authorized GE repairman, specifically RC Appliance in Sparks, NV. When he tried to get the gasket out, his hands turned black from the rubber. After about an hour of trying to get the new gasket installed, he had to use his pliers to crimp the gasket in place leaving large dents along the bottom edge of the door. He said the factory had crimped the old gasket in place at the factory from the other side. I am extremely unhappy about the workmanship and the fact that the gaskets did not last a reasonable time. I dont want to seek an attorney, but would rather GE contact me to discuss what must be done.

I owned this microwave for the last 5 years. Easy to installed, good appearance, stainless steel, easy to operate but fancy enough to prepare different meals to include the younger ones. Lighting very good and vent excellent.

GE Stainless steel dishwasher rust inside. Its more show than function. Size is great. GE stated in writing that this is normal for GE stainless steel appliances as GE stainless steel is not real stainless steel. Rust is not covered by GE warranty!

I called and emailed GE about a microwave that is in my summer home. Its probably been used a total of 15 hours. They suggested a tech. I asked how much and they told me about $95. I said it died, why not replace? They told me they will give a good discount, yada, yada. As I point out, now I have to install it again so whos going to pay for that? They keep stalling and Im still waiting. I also have over $8,000 in GE appliances. I guess I will not buy another. They do not stand behind their products.

We normally purchase LG appliances but this time we purchased a GE Profile induction range and GE Profile above range microwave oven. The relay went out on the microwave oven about six months after we got them. Their website for scheduling service is absolutely horrible and didn’t work multiple times and when I was finally able to schedule, it was two weeks out. I then called but was told I couldn’t get an earlier appointment. So we waited the two weeks, then they had to order the relay. GE waited until the part was delivered to us to schedule the return visit - over 2 1/2 weeks later! So at this point we are without our new microwave for over a month and a half. Moral of the story is never ever to tempted to buy from GE, LG appliances & cust service are great.

If you have a choice, run away from GE like the plague, because if you have to make a warranty claim, it may become a nightmare. I purchased a new home May of 2015, and my wife and I paid for the appliance upgrade to the GE Profile, which werent cheap. Less than 2 months I noticed that the microwave had a burn spot on the bottom of the door where it sits against the exterior of the microwave, the paint was burnt from the metal, and the rubber seal melted. I did not think too much of it because the microwave still worked and unless you opened it you did not see it, so it wasnt so much of an eye sore. Fast forward to January 2016, my wife informed me that the microwave stopped heating, and that she was going to put a ticket in to New Home Warranty, I informed her that we probably need to go to GE directly as I knew that is what they were going to say. So I called GE and put in a Service ticket. They informed me that it was going to be a little over a week before anyone would be available to come look at it, to which I was OK with. The repair guy finally came. I explained to him in detail what the issues were. He opened the microwave, closed it back, wrote some things on his computer, and told me that he ordered a part called the magnetron tube, which sounded like something from the transformers. He told me it would be a week before the part would be ordered, so I asked him if it wouldnt be easier for them to just replace the microwave. He told me that it is a warranty repair and they have to try and fix it first and if not, then they will. The evening before the repair guy was supposed to show up to change the door and the magnetron tube, I got a voicemail stating that the part will not be received until the evening of the repair, so they rescheduled me for 2 days later. GE just assumed that I would be available, because I probably sit at home all day waiting for service repairs. I called back the number to see what was going on. I was adamant that they replace the microwave, because by this time it was already 3 weeks without a microwave. And with small kids in the house it was very annoying to have to put a pot on the stove every time you needed to heat anything. After 45 minutes, I was still nowhere with them, so I ended up sticking with their new appointment window. I was leaving for work 2 days later when I noticed the repair guy at another home in the community. I thought to myself why couldnt he have done our repair the same day if he were already going to be in the neighborhood? About 45 minutes later my wife called me and told me that the repair guy showed up to repair the unit, that they were supposed to repair a day later, only to be told that the damage on the door was caused by arching, and that it will happen again so the microwave is non-repairable, so they will have to replace it. He told my wife that she will be receiving a call from the warehouse within 24 hours to schedule the replacement once the microwave is available, but she could call the warranty repair department to see if they could expedite it. After another 25 minutes on the phone going back and forth we were told that it will be about 7-10 business days before the microwave may be available. Now it is good to note that the warehouse where they stock the product is only 2 hours away from where I live. So by the count of it by the time we receive a new microwave, it would have been about 5 to 6 weeks from the initial call to get the issue taken care of.

I purchased the dishwasher in August. In September, two months later, it would not drain. GE sent a service tech out under warranty who found food particles stuck in the drain pump, removed them, put the dishwasher back together and went on his way. Since then, we have been basically rinsing the dishes clean before even putting them into the dishwasher as, obviously, this dishwasher cant handle much. I have also been keeping the drain filter screen spotless. Two months later, the drain is clogged again. GE sent a second tech out who said that the first tech should have repaired the dishwasher.The problem is that GE knows that the drain pump screen and the filter screens are inadequate and let food to pass through and block the pump. GE has redesigned the pump and the screens and filters and even added a filter to the design and we will get all these new parts installed for free and the dishwasher will then work as it should. Tech ordered the parts on 12/21. The service call was scheduled for tomorrow, 12/27. I got a call today from GE saying the parts had not been delivered. I know this because they are being shipped to my house and they have not arrived. GE called to reschedule the service call to January 6th, 2020--another week and a half away!!!! Clearly, this dishwasher is not working as it should and GE has a problem on their hands. I am now weighing my options as I sit on hold on GEs Customer Service line as I wait for someone to complain to. But as the dishwasher is still only a few months old, I am tempted to load it up and bring it back to the big box retailer from whom I purchased it and demand a refund. This is ridiculous!!!!

GE had recalls on models 8500 and 8700 due to the motor catching fire but not my 8600 which is right in between. So besides it being the worst working dishwasher weve owned by not even cleaning well, the unit catches fire and almost burns my house down and GE wants to give me a credit toward buying another fire trap as opposed to replacing it because its 5 years old. I expect appliances to last more than 5 years and not catch on fire. No more GEs for me!

I bought a GE over the range microwave, model #JVM1540DNBB and serial #TS903298B, on January 28, 2010. The keypad shorted out about the middle of July 2012. The microwave just comes on all by itself when nobody is around.

My 4-month old dishwasher started to leak so I called GE to repair since it is still under warranty. Technician said there was a superfluous piece on the gasket which he removed. Dishwasher was fine for about 2 cycles when it started to leak again. As GE do not have a weekend service I had to take a second half day off work. Different technician said the gasket was not pushed in correctly and I should check it each time before running it. Shouldnt this be part of the design - a gasket that stays put?! Ran the dishwasher. Water all over the floor. The new floor that is getting ruined by this clearly faulty appliance.

Purchased a microwave 5 weeks ago. When cooking it smells like something is burning. GE would only issue a goodwill certificate. Now Im forced to buy another GE product. After taking the cover off its clear that one of the connectors actually melted. It bubbled up and turned black. Because of this and the fact that other reviewers had the same problem. I dont want to buy another GE product. I dont think its unreasonable to get a refund since its only been 5 weeks. If I have purchased at a different store with a longer return policy I would be able to just bring it back to the store. Apparently the quality of GE products has gone down. I would not recommend.

I purchased a GE Cafe Over-the-Range Microwave along with a GE Range. It was delivered on Nov 2009. The control panel started acting up and quit working altogether in May 2011. I called GE and found that the replacement part and repair was almost as much as I paid for the microwave. After talking to several people and making my case, I was told they would give me a discount on replacing my unit. I was to look at microwaves and let them know which one I wanted. I have left several messages and no one at GE will return a call.

I purchased a stainless steel GE dishwasher for $508.68 since I remodeled my kitchen October 2016, I contacted GE in March 2017 because the stainless steel on the dishwasher door started to have rust spots, they sent a technician to look at it, they told me that they cannot replace it because the aesthetic warranty is only good for 30 days. They authorized the technician to replace the door, however I have the same issue with the new door, and also the dishwasher stopped working. I contacted them again. The technician was able to fix the dishwasher, but as far as the stains on the door they told me thats an aesthetic issue. They cant do anything about it. I called the consumer relations department. I spoke with CIARA GE case # **. They offered me a small discount and I have to come up with $400.00 to buy a new dishwasher.I feel that a good business should always stand behind its products. The dishwasher obviously is defective, they sold me an appliance that supposed to be stainless steel but its something else, the right thing for GE to do is to exchange the defective product for the right one. I am very frustrated that in less than a year I have to spend over $900.00 for a dishwasher. I am great customer for GE, I remodeled my kitchen, I purchased a GE refrigerator, cooktop, oven, kitchen hood, microwave and dishwasher, I think I deserve better than a small discount for a defective product.

Wife called me at work to tell me our house is filled with smoke. Our GE dishwasher caught on fire 20 mins after she did a load of dinner dishes. Thanks to my 10- and 4-year-old kids who were in the living room playing, when they smelled smoke, they quickly ran and got the fire extinguisher and yelled to my wife. They ran out of the house and called the FD. Their quick thinking prevented it from getting worse. While on the phone, I had her go and turn off the circuit breaker. We got lucky this time, someone was home...

This microwave is nearly 20 yrs old and is still working great. We replaced the handle but other than that it has been great. I would definitely recommend the GE brand as it has been very reliable. I give this product a great rating.

Beware of GEs scam! My new house came with a GE microwave oven model JVM1630. It no longer heats food so I called GE repair. Heres basically what they told me: It is likely the magnetron tube and it is still under warranty, so no charge to replace it but I would have to pay $99.95 for the repairman to come to my home to diagnose the problem. If I decided I didnt want to repair the microwave, I was offered a $100 coupon toward a new one but it had to be a GE and it had to be bought on their website only. If I decided to go ahead with the repairs, the $99.95 would be deducted from the bill and I would only have to pay for additional parts and labor. I repeatedly asked for a ball-park labor charge so I could make an informed decision as to whether it was cost effective to have the repairman come out or just get a brand new one elsewhere. The person on the repair line hung up on me! I called back and I was told the same thing; that no one could tell me what the labor cost estimate might be. I asked to talk to a supervisor and same story. I didnt schedule a repair because I was taking a long trip and wouldnt be using the microwave anyway. When I returned from my trip, I called GE repair and again they wouldnt give me a ball park figure. Frustrated, I decided to have the repairman just come out and repair the darn thing and an appointment was scheduled for the next Monday. I had to rearrange a Monday day trip to Wednesday and set the repair appointment. On Monday, it was starting to get late in the afternoon, so I called to find out if the guy was on his way. A recording said my call was noted and I would be receiving a follow-up call. About 10 minutes later, Kim in dispatch called to tell me she had to reschedule the repairman to Wednesday. I explained I already had an appointment on Wednesday. which was already changed because it conflicted with the repairman coming to my home. She told me the repairman couldnt come because his truck wasnt safe to drive so that whole day was shot. The appointment was rescheduled for Wednesday and I had to again reschedule my other trip. When the guy finally showed up on Wednesday, he told me to put a glass of water in the microwave and start it. Ten seconds later, he declared it to be the magnetron tube. He was at my house about 10 minutes, just long enough to take my $99.95 credit card payment and to give me an estimate of $246.90 to repair the microwave which included the free magnetron tube, a $20 part plus tax and labor. The estimate had instructions on how to get the $100 coupon if I decided to buy a new GE microwave, which he said is what most people do. He didnt seem like he came prepared to repair the microwave at all. I was so frustrated and already out the $99.95, so I told him to go ahead and repair it. He said I should call repair to schedule him to come back to repair it! I told him to just repair it now and he said he didnt think he had a magnetron tube in his truck. I asked him if he would go to the truck and check! He did, and nope, no tube and he left.I think this is a great scam GE and maybe others have going. Its entrapment. They get you to accept a repairman to come to your home and charge you nearly $100 for it, but give you a coupon for $100 for a new one but it has to be a GE and can only be bought from their website where they can go as high as $500 or $600. By the way, I got on the website to find a replacement. My model had been discontinued and the only one in my price range was also a discontinued model. They charge $75 to come out to install it and another $30 to take away your old one. I called local appliance stores to see if I could unload my old microwave for parts and they all said the same thing: stay away from GE products.

Purchased an entire line of GE appliances for kitchen after having prior (still working) appliances for 13 years. Have had at least 5 services calls and countless emails and phone calls for non functioning Dishwasher. Here is response from GE Manager: I have reviewed the pictures and no I would re-wash those 4 dishes if they came out of my dishwasher prior to using them with my family. Dried on fruit, starches and dairy are tough for any dishwasher to take off as the sugars in them act like glue. Again for these types of foods we would highly recommend more pre-washing to make sure that they are not left on the dishes after the dishwashing cycle. CAUTION: DO NOT BUY.

Purchased the Maytag MDB7749SBM stainless steel dishwasher in December 2013. The dishwasher and install totaled $700, which for that price and with Maytags past reputation, I wrongly assumed that the dishwasher would last a long time. In May 2016, slightly over 2 years, the dishwasher started having issues with the control panel. The control lock would randomly activate. I would have to reset the circuit breaker daily, leaving it off for around 10 minutes. Even with trying to go through all the steps to resolve the issue, resetting it from the circuit breaker, sequence on the control panel, the dishwasher wouldnt work. I called Maytag and after 40 minutes on hold, they finally answered. They wanted $89 for a service call and for the $143 part, plus labor. Might as well just replace it with another brand like GE, or Samsung.

In 2012 we purchased a GE microwave for around $500.00. It lasted with moderate use until 2017 at which point, it almost burned our house down due to malfunctions of internal parts. After many hours on the phone and several repair visits, GE agreed to replace it. The replacement lasted until March of 2020, at which point it started tripping our breaker. I took a half day off of work waiting on a repair technician. The technician came out and replaced a switch. Two hours after he left, the microwave stopped working. I called GE back and was given another repair appointment, again taking a half day off of work, I waited for the technician. He arrived and stated that the door of the microwave was causing it not to work and he ordered a new door.I called GE and was given another repair appointment. Again taking a half day off of work, I waited for the technician. He arrived and replaced the door. That evening, we noticed that the internal light would not shut off when we closed the microwave door. Two days later the microwave started producing a burning smell whenever we used it.I went out and purchased a $50.00 microwave from Walmart. This experience has been beyond what is reasonable for a customer to experience. I have received numerous automated emails from GEs consumer relations department from a GE consumer relations employee that is allegedly been responsible for my case. I have never actually spoken to this person even though I was advised numerous times that she would be calling me. As of this point, I plan on never purchasing another GE product nor can I in good conscience recommend to anybody that would inquire, purchasing a GE product. The customer service I received has been bad to say the least and the product even worse.

The arching of the metal rack caused smoldering in the microwave. I prepared a baked potato in the microwave. I smelled something burning. I assumed the potato was burning. I removed it, used the microwave again and smelled the burning again. Upon close examination, I removed the rake and that is where the burning and smoke is. The plastic hook/holder was melted and the side of the microwave was charred. I called GE and they said I should not have been using the rack with such a small amount of food. I have used this microwave almost daily for years - I never knew this. They said its safe. I dont believe it is. They told me to call repair. Im not satisfied.

First, as a new homeowner blessed with select builder-provided appliances, I never imagined I would be authoring this letter 4 months after closing on the new home. Your friggin’ microwave oven light mechanism truly sucks! I lost the two bulbs a week or so ago and purchased two more at the cost of approximately $10, even though a one-year warranty was stated. That was okay, as I was more interested in fixing the problem versus starting some long-range purchase interest. So, and this is the most aggravating aspect, I have the correct pins and life is ** good, and as I attempt to insert the first, the ** pin breaks off. Okay, so I reflect on the horrific engineering of the mechanism, and I softly” align the second of the two bulbs, and the ** pin breaks off again. ** is my predominant theme tonight. As well, believe me, I am going to inform Taylor-Morrison that their respective selection of your friggin’ lousy pieces of crap is corrupt and misguided. You suck, G.E.! I’m moving forward.

Within a year and a half of buying a new construction condo, the GE microwave fan stopped working (used the condo for no more than 30 days). I read all these complaints and am not surprised. My experience with Kitchen Aid appliances (refrigerator, microwave all junk) is no different than this. If I were to replace any of my appliances, I will not buy an American brand because they are all made in some other country with very poor quality control for very high profit and low quality goals. No choice for now, other than to get it repaired. At least, it provides employment, but what a way to create employment. I would never work for such companies.

We bought this dishwasher, with third rack and steel tub, after extensively reading reviews online. We went through Home Depot and had to wait a month for the dishwasher to be delivered. We have had it just over a month now and not only does it fail to get all of the dishes completely clean (even when run on heavy cycle) it NEVER dries even with the dry boost on. We never overload it or load it incorrectly and still there are dishes and utensils with food residue after its done running which takes hours. I predict it will rust out in about five years (planned obsolescence). The only feature Im happy with is that it is nearly silent. Not hearing it run helps to not remind me how much money we wasted.

The paint started peeling on the inside ceiling area of the microwave the end of the first year we bought it. I called GE and they claimed this was not harmful to the operation of the microwave. It was disgusting to have paint chips falling onto food we were cooking. Now almost all the paint is gone and there is some rust too. How can this be for cooking and what if some of the paint is accidentally ingested? If GE did not replace or offer to repair the problem. Stay away from GE microwaves is my advice.

GE microwave turns on by itself, creating a fire hazard. We could not figure out how our plastic plates melted, until we witnessed the GE microwave turning itself on by itself. Also filed a report with saferproducts.gov. It may have to take a death of a human to have this dangerous product recalled by GE. Great business plan, GE!

This review is related to the Monogram 2.2 Cu. Ft. Built-In Microwave Oven model #ZEB1227SLSS. The GE site: https://appliances.monogram.com/us/specs/ZEB1227SLSS indicates in two places that the built-in trim kit is included (and one place where it is listed as additional), yet GE has confirmed that in fact, the trim kit is an optional add-on with a $325 additional cost. Calls to GEs consumer line have been disappointing. Me: Your website says its included, and is in a section with other features that are in fact included but not additional fees; GE: We have confirmed that the trim kit costs extra. We have, in fact, purchased the oven and are awaiting its installation, and I have other experience with GE Monogram appliances so I expect this to operate well. But I cannot understand their reluctance to acknowledge this error on their site. Potential buyers, please beware of this issue.

I love the GE. I bought a GE dual fuel range about 3 years ago when my 6 yr old Frigidaire stove caught fire. Always wanted to cook with gas but have electric oven and broiler. It's also easy to clean the cooktop unlike older gas stoves. Love the big fast boiler eye.

Bought the new dishwasher in Dec. 2013. In November 2014 a month shy of warranty expire, the detergent dispenser did not release or partially released the detergent. GE sent out A&E Factory service to fix. First visit initiated the parts order which was a new computer board and a Cascade Series detergent dispenser. A month later the second visit to install parts, the A&E tech was at our home for 3 hours and it took that long to remove and replace detergent dispenser. The tech did not replace computer board stating it was not needed? A week later the detergent dispenser still did not release the detergent! Called back to set up another appointment which was at the earliest Jan 19th 2015. Meanwhile last Friday Jan. 9th 2015 the dishwasher started to smoke heavily causing smoke detector to go off at 9 p.m. at night. Thank goodness!! We were home so that I could disconnect the power. Third visit was 1/12/15 and was informed by Lead A&E tech that the board should have been replaced and that the tech that was sent out was a trainee and inexperienced to work on my dishwasher. He should of never worked on my dishwasher(!!) according to the Lead A&E tech. The Lead A&E tech also stated that my model has had a problem with the computer boards which is essentially the brain of the dishwasher. I am currently taking my fight back to GE since A&E Factory is a subcontractor to GE and is not authorized to replace appliances. I told GE that I want a new dishwasher that is not using the problem computer boards even if it is an upgrade. It is not our fault that they have work with A&E who send out inexperienced techs to work on complicated GE appliances. We want a dishwasher that we both feel safe to run while we are not home. Is that too much to ask for?

I purchased a slate dishwasher in Oct, 2014. After the third cycle the soap would not dispense (door would not open) or the soap dribbled out and remained running down the door. I had to run the cycle twice to get the dishes clean and for the soap to dissolve. I called the store at which it was purchased. A tech came out and replaced a part. Did not work. After the second time, when the tech said nothing was wrong, even though he saw the soap running down the front door, I called GE. They sent a tech from a different store. After the eighth repair I told them I wanted it replaced. They had already replaced the soap dispenser twice, the control board and even told me to move the baskets (ridiculous). They also suggested I run hot water before the cycle! They said if it was repairable they could not replace it.We went back and forth with this and they finally agreed to replace it. Got the new slate dishwasher in July, 2015. After two cycles I started having the exact same issues! I will not deal with GE or ever buy another of their appliances. I will tell everyone I know not to deal with this company. Quality is terrible and service was extremely frustrating, having to take off work numerous times and wait hours for the service person. In the end, it never worked!

My husband and I bought a GE dishwasher from Nebraska Furniture Mart in April 2011. We installed it in our new home in May 2011. It has never cleaned our dishes properly. Our dishes come out of the dishwasher with a film on them and do not look clean at all. I called GE in July. They sent out a repair person who proceeded to tell me that we were not cleaning our dishes well enough. The person also told me that our water wasnt hot enough, we didnt clean our dishwasher out often enough, etc. After I corrected everything, the repairman suggested our dishwasher still wasnt working properly. So, we called GE back. We have since had two additional repair men out. Neither one has been able to repair the dishwasher. The last repairman replaced a valve he thought might be broken. However, it is still working the same. I am absolutely disgusted with the experience I have had with GE.

I work as a service tech for a major insurance company. I am a master tech, and master electrician. The company that I work for owns an apartment complex which is used to house company executives whose offices are located at other sites, but often come to the Chattanooga Site to work short term. I was called to repair an old dishwasher in one of the apartments. Upon looking at the existing dishwasher, I decided to replace with a new one. I received a new GE model GDF 510 PGD 1WW dishwasher on November 8, 2013. As usual I unpackaged the appliance and examined the exterior. Finding no visible damage, and with the help of a master plumber, I removed the old dishwasher, and installed the new one. After all the connections were made, I opened the door, removed all the packaging from the dishwasher, and found the upper spray arm lying in disarray in the bottom of the machine. Assuming that this was the way that the machine was packaged, I installed the spray arm, plugged the machine up and started the machine as the operations manual instructed. The machine would not work. The power lamp would burn solid for a few seconds and start flashing. I tried to start the machine a number of times while reading the instructions, and while my partner read the instructions aloud, but with no results. Finally, I used a screwdriver to hold the door switch closed, pressed the start button and the unit started. The catch mounted on the door would not make the door switch, mounted on the machine body. We tried to adjust the switch and the catch, but with no success.The dishwasher did not show any signs of exterior shipping damage, but for some reason the upper spray arm was off and lying in the bottom of the unit, I found a small piece of broken plastic and a screw in the bottom of the machine, and the door switch would not make. Outside that I have no complaints. I am not sure where this machine was assembled, but it certainly was not equal to the machine that we removed. Thanks GE for making my job harder. I will have to find another dishwasher Monday and replace the damaged one, and perhaps send this one back, but the replacement will certainly be another brand.

Purchased my GE Profile series dishwasher several years ago and it has served me well over countless cycles. There have been a couple of occasions that it required repairs (water leaking) but had been done so under warranty conducted by an actual GE tech. When this unit finally reaches its usable service life I’m most likely to consider a GE unit again.

Wow, Donna from NJ, I could have written your dishwasher report! But since I didnt, I have never been so disappointed in an appliance purchase as my new GE dishwasher! Not only are some of the dishes & silverware coming out more dirty than they went in, it takes a ridiculously long time for a cycle. And if there are more than a couple of tablespoons of water on the door, it will pee out onto the floor when the door is closed! Not to mention that there is junk stuck to the floor just inside dishwasher, under the door, after the cycle has run! Yet the worst part is how dirty dishes are after even a Sani Wash cycle! Sometimes, the detergent lid is still closed. Sometimes its open, but the detergent is still there. Even then, dishes may be cleaner in appearance that time, than when the detergent is gone. A water glass, may have gritty stuff - not just detergent stuck and hiding down inside, or more obvious all over inside the glass. I have spent the past year experimenting with various things: detergents, amounts of detergents, arrangements of dishes, heat of water, pressure of water, rinsing dishes before cycle, etc. Glass and pottery normally fare better than plastics, but again the plastic may have started cleaner than they come out! The dealer has been out three times, finding nothing obvious the DW itself, nor anything I have done wrong. He has been told there is a kit that would fix the performance problem, but he cant purchase it, nor can his distributor. I have been told the length of cycle is because our government regulates the amount of water used. So my question is, then its okay to use more electricity?! Its totally embarrassing to serve someone a drink in a glass that is found not clean near the end of the drink! And I, too, have an old 12-years-dishwasher that still works! It was even a cheaper brand. I never had to think where pieces were arranged in that dishwasher. I just thought, in my newly built house, I should have new appliances!

Less than three years ago, I purchased a microwave oven wall unit to replace an existing unit. Due to the size of the built-in cabinet, I was limited in choices. The cost of the unit was $2400. A few months ago, the interior wall of the unit began rusting and the enamel is peeling. I contacted the customer service dept via e-mail on their site. I was asked to send pictures and then informed that I should stop using the unit immediately due to the danger of arcing. I was also told that because I did not purchase the extended warranty, the best that GE could offer me was a new unit for $800. I asked for names of warranty companies and was given one name and number but told there were others that also offered the same service. I called this company and they clearly told me that the peeling and chipping was a manufacturer’s defect and would not have been covered by an extended warranty had I purchased one from any company. Then I contacted the GE repair service center and spoke with them. The man who answered explained that this is a cosmetic problem and that there was no danger of the microwave arcing unless there was less food in the microwave than the size of the area that was chipping. I am very disappointed in the response of GE, the pressure placed on me to make a decision in 7 days or the offer would be withdrawn, and the fact that the service department and the consumer service (complaint) department gave me entirely different responses to the same information and problem. I will probably have my cabinet rebuilt to avoid having to replace this unit with another GE appliance. Who would pay $$1600 for the use of a microwave/oven unit for less than three years? Unfortunately, GE seems to be the only company that makes a unit that fits the existing cabinet in my kitchen. Disappointing to say the least.