Add me to the Dacor hate list. The $4300 oven installed in 2000 is now a whopping $6400. My motherboard #2 is broken and the glass on the door cracked which to me is a safety issue. This is a two adult, no kid household so figure. We use the oven about 7 times a year. My Dacor rangetop and hydraulic exhaust have both required service as well.

Liked the look of Dacor oven and fit in with remodel. Relay board replaced year after warranty - $600. Then after 8 years of light use (have Thermador home pro stove), another circuit board failed, part no longer manufactured. Oven now worthless and headed for landfill. Outrageous! Large national appliance retailer says Dacor not reliable. Daughter had major problems with Dacor fridge. Have purchased Kitchenaid replacement on recommendation of same retailer. Built to not last...shame on you, Dacor.

I went to put something in the cabinet at the top of my built-in wall oven and noticed the cabinet door was warm. Then, I noticed the heat was coming from the top of the oven at the control panel. I am afraid of a fire breaking out in the cabinet now. The oven is less than a year old. We just remodeled our kitchen and installed the ovens in May 2012 and this is just June.

We installed 2 Dacor wall ovens, a 5-burner cooktop, and a downdraft fan in 2000. The convection ovens bake perfectly and have performed without fail. After 7 to 8 years of daily use, we did have to replace the door hinge on the oven I use most often. We are in a rural area so the repairs are accomplished through Sears. The replacement parts arrived in a timely manner and the oven has worked perfectly since. The cooktop is easy to clean and the heat is even. The downdraft fan is effective and easy to clean. I would be confident to recommend Dacor products.

When I bought my house, the previous owners told me that theyd been having problems with the Dacor oven. They had purchased a replacement burner and prepaid the Dacor authorized service technician to install it for us. We have worked for three years now to get Dacors authorized service representative to install the part for which he has already been paid, and have been using a toaster oven to prepare meals for a family of four the entire time. The oven will heat to 135 degrees, then either shut off completely or immediately switch to broiling mode and burn whatever is inside it. When I called Dacor to see if they could help with the service issue since the technician was authorized by them, they told me it was my problem, not theirs. Although if the product they manufactured wasnt faulty in the first place, it wouldnt be anyones problem!

I bought this beautiful range and choose Dacor but when we used the Green Clean on it the enamel pealed off a spot on the bottom of the oven a 2x4 inch patch. Now Dacor say that this is cosmetic and will not honor their warranty. I have been calling them daily because they do not call me. Their service sucks.

This is a follow-up to my initial complaint, which was posted on November 28, 2011, and an updated posting on December 27, concerning problems with our Dacor range. What we learned was that the local appliance shop that services Dacor quit working on Dacor appliances, so we were left with no repair company. We were contacted by the customer service representative from Dacor, who has been very diligent in working with us to find a solution.Yesterday, the Dacor regional service supervisor from Washington came to Casper to work on our oven, which is now totally functional. Pretty amazing customer service! He did share with us Dacors challenges in getting qualified local service companies, especially in smaller towns. I applaud Dacor for going the extra mile (1,000+ miles, to be more accurate) for us.

I have 2 single ovens side by side and have a cooktop and ventilation system - my experience with the cooktop and vent (2000) was so good that I did not hesitate to buy Dacor MorS130S ovens. They were installed in my new kitchen in September of 2012. I had my cooktop and ventilation system reinstalled. My daughter accidentally cleaned the oven without taking out the GlideRacks (which are hard to take out). We oiled them, etc., like the manual says if they are accidentally left in - they will not glide at all and now I am being told $300 each to replace excluding the cost of the service call. This is ridiculous. What kind of design is so poor that racks would get in this condition? I had Bosch ovens before and their warranty was wonderful and I, luckily, bought a Miele dishwasher which has a 10-year warranty. I would not buy Dacor again because of the warranty and because of this problem. I am beyond disappointed as I love my cooktop etc. I feel that Dacor should at least pay for part of these GlideRacks.

The oven temperatures fluctuate while baking. The company was at first responsive. They replaced the oven controller and the temperature sensor. This did not fix the problem. When I called and left messages, there was no call back or response. Very poor customer service.

We got a U43 relay error on our Dacor oven of 4 years. When we finally add up the cost to replace the part, it will exceed $500 and Dacors only response is, Sorry, it is out of warranty. Of course I do not understand why a relay board on an oven would short out after a few years. Not happy and would not recommend the manufacturer.

We moved in our new home in June 2019. We had purchased 2 Dacor dishwashers, 2 ovens, a gas cooktop and a microwave. All the appliances are beautiful. That said, both of our dishwashers leaked so bad we had to stop using them as they were damaging our wood cabinets and floor. Dacor sent service persons out after multiple calls and replaced the seals, but they still leaked. Our cabinet company that sold the Dacor appliances stepped up and replaced them both with Bosch dishwashers.Our Dacor Refrigerator went out in mid February and will not cool anymore. After 2 hours on the phone with a Dacor representative, we finally were able to schedule a service person to come out a week later (Dacor has very few support companies so dont plan on anything happening too soon when there is a problem). Was not able to repair the fridge and said it could be another two weeks to get the part and return. That said our service person is a great guy and cares, but has to rely and wait on Dacor for responses and parts.Our ovens take twice as long to cook as any other oven we have ever had. We are asking them to look into that as well. Overall, very disappointed. We understand having problems, but expect Dacor customer service would be much better and support their own field service persons and clients or at least act like they care. Not looking forward to calling them back to see why we need to be without a fridge for 3-4 weeks total....

Dacor representative has been helpful in responding to my complaint and has sent new oven racks which I greatly appreciate. I was able to send them pictures of the damaged racks. I want to clarify that the warranty that was sold to me by an upscale appliance center was NOT a Dacor extended warranty and I believe that this caused my issues to slip thru the cracks. Nothing can be done about the interior that seems to have a film of sorts on it, short of replacing, but I am grateful that Dacor customer service went out of the way to correct the problem with the racks.

I purchased my Dacor Epicure Range 8 years ago when I remodeled my kitchen. My other appliances were made by GE and Bosch. Ive had to service my GE appliances a couple of times in the last 8 years, but it is the Dacor that has given me the most grief and it was the most expensive appliance purchased. It has never been reliable with regard to convection baking. Initially I thought it was my inexperience with a convection oven. I read everything I could get my hands on and kept trying...after talking with a friend who does quite a bit of baking I realized its not me, its my oven. Then the real problems started. First it was the broiler/ignitor, next it was the membrane in the keypad. Two months later it was the relay board and this time it was the broiler/ignitor....Again! Started calling Dacor when the relay board went out because at this point I had spent $1,000 on repairs....after I had paid $4,000 for the range itself. For the last two repairs Dacor has paid for the parts, while I paid for the service call and labor. This has reduced the cost of my last two repairs by about 50%, which is very helpful. However, Im still very disappointed in the product. I spend a good deal of time in my kitchen and do quite a bit of baking, cooking, and canning. I thought that if I spent more money and bought a high-end appliance, it would serve me well. At the rate that Im going, I will need to purchase another range, unless I want to keep throwing money into repairs on this one, which I dont. I will not ever purchase (or recommend) another Dacor product again.

Dacors wall oven wont heat up after I used Self Clean feature. Dacor said there is a reset button behind exhaust frame on oven (close to door latch). I called when I could not find red button and was told it was hard to find and they did not know exactly where it was located. Maybe I should call repairman. Any suggestions? Has anyone else had problems after cleaning oven? PS: My 5 year extended insurance expired Nov 11.

I purchased this upgrade to my kitchen renovation. The stainless steel stove has a great look, but that is all it has. This is my third repair (with much difficulty). The same problem - the bake ignitor goes bad and sends gas smells throughout the kitchen. On Christmas day, after preheating the oven, I opened the oven door and the inside was one large flame. The heat was intense and my right arm got hot from the heat. I immediately closed the oven and cancelled the bake setting. When I called Dacor the following morning, I thought I was talking with a robot. No emotions, no sense of caring. They must be programmed. I got no satisfaction. I said, Do you understand? My stove went on fire and on Christmas day. My family was not sure if they should leave my house. I am extremely disappointed with Dacor.

2017 purchased 36” range. First year- self cleaning overheated, replaced part. That was in 1 years warranty. But now: only 3 years barely: (I dont even cook much). Oven turns off by itself if I open the door. Oven does not turn off when I am done cooking. If I cook 450f pops warning of temp overheat. Called ABT service (this is where Dacor said) it cost $219 for a service guy to call dacor and to give me answer: I think it is android board. I have to buy a board. Plus per Dacor this board will not have wifi. So there is no Discovery- paid extra for extras I can not have...

We have owned our dual-fuel Dacor stove for about four years. We purchased this stove because we needed a down-vent - this is how our kitchen was already configured. We had only the Dacor or Jenn-Air stoves as choices and went with the Dacor. I have been thoroughly pleased. Everything works consistently including the self-cleaning feature. Prior to this stove, we had a Thermador which was expensive and NEVER worked consistently. One feature or another was always on the brink. The Dacor is such a relief. And good looking, too.

First six month, dishwasher rusted on the inside. Dacor gave us a less expensive in its place. First year, microwave was repaired five times. Microwave has a piece of wood to hold the door in place. Wall Oven, the broiler never work. Present, range oven does not work at all. We have a repairman that is trying to get parts. Present, refrigeration control panel does not work, need repair. These appliances were to be a our luxury kitchen, but turn into a nightmare. Do not buy this appliance, you are wasting your money.

As I have read in most of the reviews, we have also experienced the control panel on our 30 inch dual range cracking over the years. We were told not to replace it because it would continue to happen. Ok, lived with that... Now something new has started to happen, the plastic handle on the oven door and surrounding area has started to melt. It got so bad after a self clean that it is collapsing. Now there isn’t much of a seal at all when the door closes. The stove isn’t brand new, but this has to be a fire hazard, and consequently, now the oven will not even turn on. I’ve reached out to Dacor with no response yet. I’m done with this company!

Im planning a kitchen remodel and stumbled on this site. I have a Dacor dual fuel range (stove wont light, oven wont hold temp), hood (light wont stay on consistently), microwave (replace once, okay now), wall oven (panel out) and warming drawer. Only the warming drawer is working correctly. I live in rural Kansas and I cant get anyone to do repairs. I really like the design but... its time to move on to a new brand!

I purchased entire kitchen of Dacor appliances - $30,000. The 48 refrigerator required 9 service calls to stop freeze up. Wall oven – the digital panel went bad. Stove top exhaust – the circuit is melting. The dishwasher had 17 service calls over 2 years - mid way they replaced the unit because they could not stop it from leaking and damaging our wood floors. The most recent service call was yesterday, 12/20/2011. After waiting since November, it is again not working. Does anyone else understand that spending $1700 on a dishwasher should allow you to use the dishwasher? I called the customer service and was told We are discussing the situation and will get back to you. Are you going to come wash dishes with me over Christmas when we have 25 guests? Were you there on Thanksgiving? If I hadnt been stupid enough to buy all Dacor appliances, I would throw it in the dumpster and buy a GE from Home Depot.

Dacor customer service contacted me and worked with me and the appliance repair company to get the proper parts to fix the oven. Everything is fine! We once again really love our Dacor wall oven.

I am writing to complain about our Dacor dual fuel stove that we purchased in 1998 when we built our house. Initially things went well, and I enjoyed baking in the oven and the convenience of the gas stove top when we had power issues. But then the honeymoon ended, and the problems started. After completing our first self clean cycle, we started getting the F1 code, and noticed cracks in the front on the stove. Our repair guy came out, took a look, and then informed me that Dacor had had numerous problems, and were not so good about living up to their warranty. He was right, Dacor felt in no way that they should help resolve our problem. With 4 kids, you cant just go without a stove, so we paid for the parts and repair. I figured it was just a one time thing, but I was wrong. We are now again looking at replacing the same part just 3 years later again with cracks and the F1 code. Dacor should be ashamed. Do the math. If they walk away from responsibility on all of these faulty products that average $5,000 a piece, shouldnt they have the money to pay for the fixes or maybe hire better engineers? They need to be held accountable for this mess. I need my oven back on!!!! And after the money we have paid for repairs, light bulbs, and parts...... the rest of the care should be free and on them.

We have an 11 year old Dacor double oven with convection on top. The relay board malfunctioned and there are no parts to repair this. All Dacor would tell us is that they dont carry the parts anymore. Evidently, they are not required by law beyond about 8 years and that appears to be all they do. Our appliance repair person even contacted a company that rebuilds electronics and they cant get parts for this board. It is unbelievable considering what we paid for the oven. So we now have to replace it. Dacor offered us a discount on a new one. Not good enough. I cant imagine putting another Dacor product in. Two appliance service people have told me that Dacor has this reputation and they would not put them in their own houses.

I purchased a DACOR Discovery IQ Range one year ago Model # DYRP36DS/NG from an online authorized DACOR retailer. Here is a synopsis of the events Ive had with the range over the past 12 months: I took delivery of the Range in January of 2016 at my home under construction. I moved into the home in April 2016 which is when the Range was fist installed. In May I began to have problems with the unit, it would shut down during preheating, then reboot itself, sometimes it would just reboot itself randomly. I called DACOR customer support who told me that I needed to download the latest software version, which I did. Shortly thereafter, the Range again would shut down during cooking and go into a reboot cycle.I called DACOR again, they sent out a local service company. In June the technician came out and upgraded and re-installed the software. The problem continued, I contacted DACOR AGAIN, got the run around, etc... Escalated the problem. DACOR then determined the problem was in the internal circuit board which they arranged to shipped to local service company. The service company came out again, replaced the internal circuit board and attempted to upgrade the eProm, which didnt work. The Range was in a constant state of rebooting itself over and over and over again. The Technician left. Said nothing more he could do. I had to shut the power off so the unit would stop rebooting itself.I called DACOR AGAIN, I got a complete run around, they refused to do anything more. I finally was able to reach the V.P. of Customer Service. After a few conversations and investigation into the issues. She determined that the unit needed a new front controller panel. The panel was shipped to the local service company. The service company came out again and replaced the front controller panel. Its now November. Over Christmas, the unit began to shut off the oven randomly during cooking cycles, for no apparent reason. Over New Years, the oven was shutting off, flashing an error code and reboot! I called DACOR last week. They refuse to help because now it is out of warranty.Ive contacted the online retailer. Ive left messages at DACOR for the Service Manager and the V.P. of Service. NO RESPONSE. So this is how DACOR deals with servicing their high end appliances, keep trying to pretend to fix the lemon appliance until the anniversary date, and then they dont have to deal with their $9,000 piece of garbage high end range any longer. The consumer gets screwed and DACOR doesnt care in the least! DO NOT BUY an appliance from DACOR.

Have had an on-going issue trying to replace an oven door....since early December 2020. Have gotten a continuous run around regarding status of new door and shipment of same. Friendly Customer Service Reps do nothing to solve this issue. The oven door is designed not to be repairable or user friendly. Poor support and steady excuses have created another DIS-SATISFIED CUSTOMER!! AVOID DACOR!!

We built a home in 2006 and installed all Dacor appliances. I would never ever purchase these products again. My gas cooktop was the top of the line product from Dacor and I have had nothing but problems with it for 5 years now. I have spent over $1000 fixing the large burner that continues to have leaks with the seal to the point where the flames come out the bottom of the burner. Most of the other burners click when lit even though they are clean and away from a draft. I have had 2 Dacor approved repair companies out and they both recommended against Dacor. In addition, the finish on the cooktop has soaked in my heavy duty cooking juices and foods and the stains will not come out. Apparently, this is due to the new finish they used so that the metal can withstand the high temperatures. If this company were an auto mfg., they would have had to do recalls and face potential class action suits. I would prefer to be cooking on a camp stove rather than my Dacor. When I contacted Dacor, they offered parts at a reduced rate which still cost a fortune. When I asked about replacement, they said they would sell to me at a discounted rate which was still $2400. Bad product, bad company. My cooktop is still giving me issues. it is embarrassing to cook with friends around because of the problems.

Updated on 05/12/2020: I wrote a review of our Dacor kitchen and gave the company a review of 2 stars because the cooktop, ovens, and hood blower all have failed at some point. The real issue is that the company doesnt support products after sale to quote them they do their best... The other problem is this site, it allows companies to claim they are or have resolved issues, without a response or comment from the customer about what the Companies Resolution entailed. Sending me an e-mail that says sorry the thousands of dollars you invested in our products only bought you up to 7 years of replacement parts, isnt what most people would call a Resolution. After months of working with the retailer and Dacor the e-mail below is what they consider a Resolution:Subject: Dacor customer service **Hello Mr. **, We would first like to thank you for staying a Dacor customer for as long as you have and would like to apologized for the inconvenience. As a manufacture we are constantly innovating products and at some point parts and units do become obsolete. Dacor does provide parts for as long as we possibly can. Once the appliance becomes obsolete we are only required to hold parts for up to 7 years. We again thank you for being a Dacor customer. Be safe during this pandemic. Have a great day. DENISE ** | Customer Service RepresentativeO: (833) 353-5483 x** F: (626) 403-3130Original Review: We built a new home in 2003 and purchased Dacor Preference appliances. Including a 6 burner cooktop, double 30 inch wall ovens, warming drawer, a microwave, and large hood with a remote blower. All the appliances are stainless. We enjoy home cooked meals and prepared at least one meal a day. Our kitchen is a work place not a show place. So these are my feelings after 16 years of use.The Cooktop has plastic knobs and a rubber gasket under each burner and piezo electric igniters. All of these items have failed over the years. I replaced the burners some years ago because when the gasket fails the burners sputter and liquid spills leak into the bottom of the cooktop. Replacement burners fixed the problem for a while but the burner design makes this a point of failure. Additionally, the burners were expensive so were back to sputtering burners and disassembly for cleaning. One of the plastic rings under the flame control knobs broke, weve ordered a new ring ($26) a couple of months ago but Dacor cant give us an estimated delivery date. For the past few years the Piezo electric starters only light half the burners, (they spark but the burners dont light) not a big deal but these are high end appliances, using a match to light the burners is definitely 1950s.The 30 inch double ovens are a great size for bakers like us. The Convection feature is great. However, the first time we ran the self cleaning cycle on the upper oven the door handle on the bottom oven bubbled and melted. The real issue with ovens today, is that Dacor has stopped making replacement parts including the electric heating elements. So even though we spent nearly $3,200 for these ovens, Dacor no longer supports them.The Microwave never worked correctly and we replaced it almost immediately. At that time Dacor used relabeled Sharp microwaves. Finally, Im not a fan of cooking smells in the house. So, we purchased 48 inch hood with a 10 inch inline blower. This week it failed. The motor hums but the fan doesnt turn. So replacement parts? Nope. If you decide to purchase Dacor be aware that the company doesnt provide support for their products in the long term.

As a contractor, we were fortunate enough to build our dream home which was completed in 2005. After much research and many show room visits, we purchased Dacor appliances for our kitchen. As the saying goes, if I knew then what I know now. Our biggest (note I said biggest, not only) issue is with our ESC130 oven. If you own this oven, do not, repeat, do not, use the self-cleaning mechanism. I have had this repaired once and then replaced once (along with a relay board). I seldom use this because I know when I do the lock mechanism will continue to cycle until it is replaced. This means, while I can still use my oven, I have to time when I open the door based on when the lock is cycling in the unlock position. I must also turn the oven off at the circuit breaker or listen to the continuous warning beep that the lock is cycling (as if I didnt know).After repairing this feature once, I next choose to have the mechanism replaced and Dacor offered me a discount on the parts (the oven was and still is out of warranty) at a cost of more than $500.00. This is on top of what I had already paid to have it repaired just 18 months earlier. I feared using this feature again as I didnt want a repeat performance. After cooking macaroni and cheese yesterday, I felt I really needed to clean the oven and made the mistake of using the self-cleaning feature of the oven. I dont know why I was surprised when the locking mechanism refused to stop cycling.I contacted Dacor today only to speak with the rudest customer service representative I have ever encountered, Steven. No last name. He is the only Steven who works there. He refused to listen to me, spoke over me when I did try to talk, and did not allow me to speak with anyone else. There are no supervisors available on Fridays and he could not transfer me anywhere. I left a message for someone else to call me (they did not). I called back later that afternoon and was given the name of a supervisor, Nhi. She was not available and I spoke with another customer service representative. I learned that Dacor is aware they have a problem with this locking mechanism and are trying to correct it. This got my hopes up, thinking that the company would now do the right thing and replace this mechanism at not cost to me, or at least at no cost for the parts. Not so. Even though Dacor knows there is an issue with this mechanism and they are supposedly trying to correct it, all they can offer me is a discount on parts. Really? Wow! A discount for a part that you know doesnt work properly and probably wont work properly because they are still working on the problem? I just really dont know what to say. Is this supposed to make me happy as a customer? Would prospective customers want to buy a Dacor product knowing that Dacor is more than happy to sell me a known defective product at a discounted price and they should expect the same? It is probably needless to say that I would urge all prospective Dacor owners to not waste their money on any Dacor product as they do not care about their customers. I will certainly be doing my part to warn others and hope this serves to warn others as well. Dacor has a lot to learn in terms of building even what could be called a good product and standing behind what they sell as well as becoming a customer service oriented company.

Worst oven Ive ever purchased by far. Pay big bucks and get junk. About 2 times per month, the oven will not heat up. I cant count the amount of wasted food and dinners out, because it does not seem to ignite, only warm up to about 100 degrees. I contact the appliance repair company and it works when they come out, so they dont do anything. I will never, ever buy another appliance from this brand.

This is the second time I have purchased these appliances and unfortunately each one has been a great disappointment. I have spent enough in repair bills to almost purchase a warming drawer. Each one shuts down when the self clean button is turned on, and then I have to call a repairman out to recalibrate the oven to work each time I try to use the self clean. I was told by the last repairman that the life of the oven is greatly shortened if you the self clean mode. If this is the case, either fix it or take out this mode. After I had the oven about a year the oven door glass blew out, and this had to be replaced. The temperature in the oven is very unreliable in different areas of the oven and browns more on one side than the other... For the high end cost of these ovens, I would just as soon have a basic oven that works and does not go out every few months. What a waste of money I consider Dacor to be, and will never recommend it to anyone I know. I am in the personal shopping business and have my own company, but will tell my clients to be very aware of the high cost/low performance of Dacor products... On a scale of 1 to 10, Dacor gets a 1.

We are in the process of remodeling our house including an entire new kitchen that we cant wait to finish to invite people over and show. HOWEVER, the cook top already has a light burned and finally the cover of it ended up falling as I was wiping down the stove (very softly by the way because I like to treat my appliances really nice). We have had this stove for less than a year I havent even made the last payment and it is already with a light burned out. REALLY? My husband spent countless hours researching the best appliances and decided to get this one and to come to find out that it is not good it is a complete disappointment. I am sooo upset. DO NOT BUY THIS BRAND!!! Save yourself the hassle that we are now going to go through trying to get a hold of someone on the phone and see what they will do if anything. I bought it from AJ Madison.

We purchased this high end Dacor range (Dacor Renaissance ER30G) new in 2011 from the Appliance Loft here in Cincinnati. It was dropped off and installed and would not operate right out of the box. A repair was made and everything worked (unless you count the indicator lights on the knobs, they all went out after approx 14 months). This past November the oven went dead. A1 appliance came out: Determined new control board needed, ordered and installed. Thanksgiving Day, oven dead. A1 comes back, reset the High Temp Fuse. Oven dead 4 days later, A1 returns with a new HTF. Dec 22, Oven dead. As soon as The holiday is over we will call another repair shop and start looking at replacing this unreliable piece of eye candy. Open comment to Dacors design engineers, quality control engineers and management. You should be totally ashamed about this product youve designed. You are supposed to represent the best in American design and quality and this falls below that of low end appliances out of China. See you in small claims court.

We bought a new house a couple years ago, and the kitchen came with a suite of new Dacor appliances - range, fridge, and dishwasher. They are all terrible.The led indicator on the dishwasher is scrambled. The icemaker in the fridge clogs up into a solid block of ice. We had this fixed, which involved a new control board and some caulking, but the problem returned not long after. The knobs on the range feel like theyll snap off any time. The lights in the oven arent seated properly and they interfere with the oven racks. It takes forever to get up to temperature. And Im starting to think I have a gas leak. How can these products be so expensive and such utter garbage? Oh, but they have wifi!

This is a follow-up comment from my last post dated June 21st 2011. My local appliance company, where I purchased this oven, seems to have helped with their recent fix. I was able to bake a white cake, following the box directions, that was not burned on one side and raw on the other; it was okay. With fall arriving, I will be back in my kitchen and will be using my oven. I will keep you posted. I still would not recommend this oven to anyone, and will not purchase any future Dacor products.

I was a bit anxious when I purchased my Dacor range because I really didn’t know how it would perform. A year later and I couldn’t be happier. I love my Dacor 30” range. It has been one of the best purchases ever.

I purchased a DACOR PGR-30S LP in 2002. It has had a number of problems due to poor design that required replacing the control panel as well as other parts. However, it has recently developed a gas leak and thus is no longer usable. To fix the gas leak, you must take off the top burners to get to the leak and make a repair. UNFORTUNATELY, DACOR has to make room for new parts and no longer makes the O-Rings required. Yes, apparently a $10 O-Ring takes too much room seven years after I bought my range. So, in 2009, DACOR discontinued making the O-Rings and now I have a very expensive paperweight that I have to take to the dump so that I dont blow up my house. I wouldnt ever buy a DACOR again. The customer service it terrible and they cant even be bothered to carry simple repair parts. Buy a Wolf or some other high end stove because DACOR is literally a piece of junk!

If anyone else has this experience with Dacor ovens, we need to have a class action suit against Dacor! While baking Christmas cookies this week with my grandchildren, my ovens stopped working and started beeping. The error code was F3. I was able to get a technician rather quickly who diagnosed the problem as a failure of the control board which affected both ovens. The replacement part was discontinued from production in 2011. My ovens are 12 years old and cost over $4,000 at the time. What a pickle I was in a week before family coming for Christmas dinner!The technician said my only recourse was to send the control board to a refurbisher and he did not know when the board would be fixed - all for a whopping costs of over $600.00! I find it unacceptable that Dacor discontinues a control board and forces the consumer to either buy new ovens or pay the cost of a refurbished part that I hope will work. After spending thousands of dollars, how does this happen? What can be done so the consumers who purchase appliances with good intentions are protected from manufacturers that dont stand behind their products? DACOR I NEED ANSWERS!!

We equipped a luxury kitchen with Dacor appliances. Had to replace the 60 inch dual fuel range after 8 years - use the same brand simply to match. Big mistake. Several repairs already. Also installed two under the counter warming drawers - nothing but problems and repair expense. Now we need a small $25 part - a cooling fan with motor that is faulty. Was informed the part is no longer available - customer service told me well, it is 10 years old. Really? We now have to rebuild part of the kitchen cabinetry and spend several thousand to replace two warming drawers? They also said the company was too small to keep parts available for a long period of time. Unbelievable! I will never buy Dacor appliances again.

This week Dacor installed my 2nd replacement gas range. I remodeled my kitchen 3 years ago and chose Dacor because I had a great experience with their appliances in the past, had their oven and stove in my kitchen for 15+ years and never had a problem. With the first new range, the oven started to automatically shut off due to excess heat escape, so the safety feature would kick in and shut the system down, in addition the knobs would become very hot even when the over was used briefly, 12-15 minutes. I was very impressed and happy with the customer service through Dacor, they immediately gave me a brand new over. Exactly another year, the new oven had the same problem, door begins to not hinge properly and heat begins escape, knobs get dangerously hot.This week Dacor very kindly, replaced my appliance with the new Dacor Renaissance 36. I used the oven for 12 minutes on 400 and the entire exterior is dangerously hot. I do not have any children, however, if I did I would be terrified that they could seriously injure themselves. The exterior of an oven should not become hot like this. Has anyone else had this issue with Dacor? I feel they have been very responsive with regards to customer service however I want an appliance that is safe.

We thought we bought a quality product when we remodeled our kitchen two years ago and put in a $3000 30 inch wall oven from Dacor through their dealer Friedman’s in Knoxville. We had heard for years that their products were top notch and high-quality. I find it interesting that the oven has a self-cleaning function. However Dacor Technical advised me that if you use the self-cleaning function you will create too much heat and destroy the motherboard. Wonderful input after the fact. The oven now does not keep a correct temperature and we are advised that our oven is two years old and out of warranty and we should not have used the self clean function. Really? Why is the button even there. Do not under any circumstances purchase any Dacor product. I feel comfortable in saying Samsung will add absolutely nothing to the quality or service. The lack of customer care and concern is beyond reproach. One star rating is way too generous. How do you just walk away from your products. We used our clean function exactly once and nobody ever said it was a self destruct button.

I am having issues with my Dacor oven and have tried to contact customer service since Monday 01/04/16. I was on hold for 27 mins and finally left my number for a callback. I have called every day and leave my number for a callback, no response. Today Thursday I sent a message and the response was that someone will call within 2 days. Great customer service. Buyer beware.

Dacor Distinctive Series Range model DR30D - One week after the appliance warranty expired, the oven stopped heating. The repair man replaced the circuit board. We still got a code 33 when we try to get the oven to heat to 400 degrees. Called customer service, they said to flip the breaker to the unit off for a few minutes. Seemed to help but we do not use the oven much, as we also have a Meile microwave/oven that we love and use that more. Then I cleaned the oven using only the ovens program. That locked down all of the gas cook top knobs. I called the repair service, it snowed on the Saturday of the appointment. They cancelled. I did not check the stove on Sunday. On Monday the repair service walks in and simply turns it on, no problem. VERY FISHY!!! I have heard the manufacture can control it by computer chips. This appears to be very true. Now the stove does not heat past 250 degrees. After speaking to a few people it appears this is a very common issues. Dacor is a lemon. Do not waste your time and money.

This is an update on my posting regarding our ER36DSCH/NG posted Dec 30, 2013. A Dacor representative has been in contact with us and has offered to install a new oven control which they think will resolve our problem. We are absolutely thrilled and quite surprised that they are footing the entire expense. Now this is what I call good customer service! Thank you Dacor.

My wife and I purchased a new Dacor dishwasher, new Dacor range and new Dacor microwave oven. Unfortunately, the dishwasher never worked and were now going through the process of getting the unit repaired. A repair technician was sent out and discovered a new CPU was needed. Then once the CPU was installed, a new circulatory pump was needed. And finally, once the circulatory pump can in, the unit still doesnt work. Weve had the technician in four separate times (installation, tech inspection, CPU install, and circulatory install) and each visit is approximately one week between visits. Yes, were now going on four weeks without a dishwasher that we paid for. Beyond that, someone needs to be home each time they visit. So now Im without a dishwasher for four weeks and I have to take four days off of work so a technician cannot fix my dishwasher. When I called Dacor customer service and asked for a temporary unit until mine is fixed, they simply stated we dont do that. Dacor may be a premium appliance manufacturer but they do not have a premium customer service department. So buyer beware, if your unit has any problems Dacor will not rush, hurry or try to accommodate you. Im sure the unit will eventually get fixed but after a month of waiting, I believe Ive earned the right to warn others about Dacors business practices. We purchased the unit from Pacific Sales in Corona, CA. When we asked Pacific Sales for assistance they said it was a Dacor issue and refused to assist us. These two businesses will no longer receive my patronage.

I bought my Dacor epicure 36 duel fuel range in 1998. First stove: oven door did not close, spark modulator out. They tried to fix it but failed. They sent me a new stove. #2 stove: same problem with spark modulator. Couldnt use any burner without the constant clicking. Oven didnt bake evenly. Complained. Stove: #3: same problems. Dacor sent me a letter to grade them on their stoves and service. I blasted them. They called me and ask if I wanted my money back or another stove. Stupidly I took the stove. This was 5 years since the original purchase. Ive had this stove #4 for 13 years. Door is and always has been unable to close. I use a stick to close it. Now the relay board is out. Frankly I so love the looks of the stove and I cant afford to get a new one. Original was 5200. Now they are 6700 and I would probably have the same problems. So I am going to try and fix this stove myself. I will never buy Dacor anything ever again, even if I could afford it. When they offer your money back, take it. The service was responsive although didnt solve the problem through 4 stoves. I would gather from that, the design is bad. My mother has a old 1940 gas stove that still works. Gas stoves should not be that complicated.

We remodeled our kitchen and decided to use the range as the focal point of the room. The decision to go with a Dacor ER36DSCH dual fuel range over comparable Wolf and Viking models as well as a Dacor heating drawer was made, a decision I have regretted since. Our unit keeps blowing the baking element ($200) which routinely fails at the most inopportune times. To date I have replaced four and the Mrs. recently informed me that the oven is once again not heating properly. Thankfully, I am competent enough to diagnosis and repair it myself and did a thorough operational inspection and cleaning which revealed the broil element ($180) had also gone bad this time. My wife hates this oven and unfortunately it sits right smack in the middle of our beautiful kitchen to remind us of the bad decision we made. In fact, we are now at the point where we are considering replacing it and sending it to a scrap yard where it belongs. Avoid this brand or it will cost you.

In August of 2005, I purchased a Dacor pro range. In December 2005, the control panel began to blink and lose display. Dacor gave me names of 2 authorized repair people. After several visits by a repairman, I phoned Dacor and was told to call a repairman. They obviously didnt listen to me! The repairman spoke with Dacor representative who responded that the display needed to be ‘rebooted just like a computer.’ Several times a month, I must go to the electric control panel in my basement to turn the breaker switch off and on in an effort to ‘reboot’. In September 2010, the display panel went dark and could not be ‘rebooted’. I had to replace to control the membrane at a cost of $530.69 plus $169 for labor and a service call. On Thanksgiving 2010, the ‘new’ display panel which was obviously defective, stopped working. Once again, a new membrane had to be ordered and installed incurring another service and labor charge! I sent a letter to Dacor wanting reimbursement of labor/service on original defective membrane and was advised that they warranty their products, not the service! It is now November 16, 2011 and I still must continuously ‘reboot’ the control panel! However, I spoke to an authorized Dacor repairman who told me that Dacor has had many complaints such as mine and now have a devise which attaches to the power cord and filters out the ‘noise’ from other household items which disrupts the control panel on my oven! Is there a reason why Dacor is keeping this a secret? Do they not want to make their consumers happy? I cant wait to be rid off this appliance and all association with the Dacor company!

I am thrilled with this stove. I have always had a vertical double oven so this is a first for me. Really pretty in my kitchen. Almost like a piece of furniture. Can’t wait to start cooking!!

In 2008, I purchased my dream home and had the opportunity to build my kitchen from scratch. At the time, I shopped Viking, Sub-Zero, Wolf, and Dacor. I made an appointment to tour the Dacor showroom and was blown away by the aesthetics and advertised performance of their line. I made the decision to fill my kitchen with Dacor products: dishwasher (ED24SCH), dual range (ER48DSCH), range hood (EH4818SCH), fridge, and microwave (DMT2420). To date, the fridge is the only appliance that has not malfunctioned. Within the first month, the microwave blew a fuse (covered by warranty). Within the first 6 months, the dishwashers motherboard blew (also covered by warranty).Since the 1-year warranties have expired, the range hoods electrical unit malfunctioned and ceased working properly ($400-plus in repair). The motherboard on the dishwasher has gone out twice ($1200-plus). The dishwasher rack has completely rusted and the wheels have fallen off ($800 to replace). The lights on my oven dial is out and the glass bottom inside the oven that covers the heating element has cracked (nothing has been spilled or dropped). In fact, I only use that side for Thanksgiving. I am extremely bummed (to say the least) and I feel that the products that I was sold do not live up to the quality level that they advertise. Additionally, the replacement parts are obscenely expensive, and at this time it makes more sense to replace the units rather than dump more money into a pit.

From the beginning, August 1997, 17 years ago, I was not able to use my oven after self-cleaning. The problem was never resolved after countless service calls totaling over $1500. Aside from the cost, I was inconvenienced every time I cleaned my oven, as I was not able to use it until it was serviced, about a two week wait. I contacted Dacor early on and they reluctantly agreed to extend my warranty for a year. They did nothing beyond that, and my oven still shuts down after self-cleaning, which I hesitate to do at all, until it is beyond needing cleaning! The circuit board was replaced and recently the cooling fan was changed, but....no luck. Buying a new oven is not an alternative, as the oven performs well in every other way and I simply cannot afford one. I cannot believe a company of such status is not interested in satisfying its customers.

I purchased a 48 Dacor Epicure stove in October 2010. We moved into our home in November just in time for Thanksgiving. We remodeled the kitchen and the stove is the focal point. When I heated the two ovens, the pre-heat mode stayed on but the ovens went to 600 degrees plus. My oven thermometers only read to 600. That happens every time and the fans stay on for hours. After many service calls, we have determined that the oven is going into a cleaning mode every time and is wired backwards. Dacor is ignoring me.

Purchased a Dacor Epicure ER36DSCH/NG RANGE and oven in 2007. Sad story, it never worked properly since day 1. Initially a gas burner did not light, they came and repaired it. Subsequently the door lock failed in the lock position - had that repaired. The door lock failed the next year again, this time thanksgiving, ruined the dinner. They fixed it but the following year the lower burner element failed at Thanksgiving. All my relatives know not to purchase a Dacor product. Problem is I am stuck with this boat anchor. The oven door motor has failed 3 more times and thankfully the service man showed me how to change it. Today we tried to bake some apple pies and found the oven temperature set at 450 was only 350 (bought an oven thermometer). This explains why it always takes so long to bake things. A complete piece of **, never ever buy one.

I purchased a Dacor range hood 3 years ago. I had an intermittent problem from the start, as one of the two lights would intermittently go off. Replacing the bulbs didnt fix it. As one light worked perfectly, it became a tolerable issue. Finally, I was having other electrical work done in our home & I asked my electrician to look at it two weeks ago. He figured out that it was a defective lamp housing that incorrectly held the lamp bulb. Dacor shipped me a replacement lamp housing for me at no charge. I installed it this last weekend and it is running fine. Thanks, Dacor!

We have a Dacor gas range RSD30R that we bought to upgrade our kitchen in 2002. We have had several issues with the range to date. The first issue we had with the range was the auto lock for the oven cleaning cycle that failed in 2007. It was not covered under warranty and cost $88. The second item to fail were the oven door springs. They also failed in 2007 and covered under warranty. They failed again in 2017 and had to be replaced for a second time. The springs are too weak to hold the weight of the heavy door. $68-$78 for the springs. The springs could easily be changed out as the brackets are still good but they only come as complete units. The last item to fail were the ignitors. Only one ignitor failed out of the four but as the spark module ignites all burners every time any one is turned on, premature failure could be expected as all ignitors light every time. This time the part is no longer available from Dacor. Dacor does not support any products they build after 7-8 years. Parts will no longer be available. I would not recommend Dacor Appliances to anyone as the manufacturer does not support their own products very long. I purchased Dacor to buy American and I regret it now. In contrast every product that Miele made even 20+ years ago, parts are still available directly from Miele and other suppliers as well.

I remodeled a kitchen in a high end house and so wanted nice appliances. I had KitchenAid (which Id had a lot of issues with) for about 16 years. (Since I built the house - the fridge was rebuilt 3 times.) While looking for which appliances to use we were at an open house and a chef was cooking and giving a talk on the Dacor ovens in it. So... I reviewed a lot, liked what I read, and chose Dacor. I love them, the cook quality, the features, all of it. BUT my double oven had issues from the start. An annoyance at first with the built in Android but I didnt complain a lot. Move forward 1.5 years and the Android tablet built into it would freeze and not restart without throwing a jumper on fuse box. I called Dacor and they gave me a number of options, disable the Android because of a known issue and get $500 back, or - return the oven for full credit and theyd pay to have it removed (1.5 years later... cmon thats pretty awesome), or - pay $500 and move to the newest higher end model with steam cooking. Wow, talk about stand by your product! Ive never seen this before with an appliance manufacturer/vendor. Certainly wasnt my experience with KitchenAid. Anyway Im an advocate even though I had a problem and thought they deserved credit here.

The wall oven’s glass was damaged by a guest. Customer service at Dacor was exceptional. Within a day of advising Dacor’s customer service, I received a call from the service man and the replacement was installed the very next day. The service man was considerate by calling first and coming exactly when he said he would. He was very professional as he replaced the glass in a matter of minutes. I would choose Dacor again.

We have had our Dacor since 2006 and this range, the most expensive appliance we have ever owned, simply doesnt maintain the proper oven temperature. We have owned several far less expensive ranges and their ovens, much more basic designs, do what an oven is supposed to do maintain a temperature! We cook or try to quite a lot but working with this stove is like baking over an open fire while camping. This supposedly gourmet, fancy, convection oven that supposedly can bake cookies and meat at the same time is a total fail. We have had the service people out repeatedly to no avail. I am convinced we could change the circuit boards repeatedly and it wouldnt make a difference because it is a faulty design. This product should not be on the market or this company and their poor service in business. DO NOT BUY THEIR RANGES! Unless you dont cook and all you will do is look at it. We are thinking about retaining an attorney to file a class action suit. We could buy a low cost oven that works several times over for what we have paid in repair bills.

We have had problems with the igniter switch which clicks when I have a large pan or pot on the stove. My husband has tried cleaning the igniter tip with a brush as well as the removable ring but we still have that problem. We also have a Dacor microwave that seems to blow a door fuse pretty often that has to be replaced.

We remodeled our kitchen in the fall of 2009 and decided to purchase what we thought were higher end Dacor appliances (stove top, oven and microwave). Well, what a mistake that turned out to be. Considering the price we paid for the appliances, you would not expect problems from all 3. Perhaps a problem with 1 appliance, but problems with all 3 suggest a real quality problem. My first indication should have been when I called and asked how to change the green LED on the microwave to blue to match the nice blue LEDs on the oven mounted right below. I was told that someone else makes the microwave and Dacor just puts their name, and that I should just turn off the LED on the microwave. I dont know if that is true, but that is what I was told.Now when using the microwave/convection feature, the oven makes a noise (sounds like a fan motor) for the first 3-5 minutes then eventually quiets down. A daily reminder of the mistake we made purchasing Dacor. Then those nice blue LEDs on the oven started failing making it impossible to read the clock, timer or temp. Luckily, the oven still works; you just cannot read the LED any longer. This is a constant reminder of the mistake we made buying Dacor as we see the LED every time we walk into the kitchen.Finally, we have the solid surface electric cooktop. Although it works fine, the black paint on the metal trim around the stove top is wearing off. Now, we have some shiny metal and some black trim. This is just an annoyance and honestly, we probably would not have even complained about it. However, with the other problems we have had with Dacor, it just adds to our overall disappointment with Dacor. If I knew then what I know now, I would be a lot happier because I would have GE appliances and not these overpriced low quality Dacor appliances.

The Dacor gas range/ oven and wall oven were here when we bought our house in 2010. I would never buy any Dacor product again. I will have to look for a replacement for the gas cooktop range. The Dacor gas cooktop is OK except that EVERY time you turn on a burner, one or two of other igniters start clicking and wont stop until you find which one it is (not always the same) and turn it on and off. Please heed this and all the other warnings from the choir. DO NOT BUY DACOR!It is all very expensive junk. The oven temperatures fluctuate while baking. The oven range unit is out of warranty. So our home warranty AHS covered it but they kept sending out the same grubby slob who never fixed the problem but did charge us for the $75.00 service fee. They replaced the oven controller and the temperature sensor. This did not fix the problem. We have a full size oven that we cannot use! Then F1 beeping nonstop, and we have to turn power off to stop it. Now, out of the blue the downdraft fan just started extending and retracting over and over again with no way to stop it without going back to the electrical panel and flipping the breaker that it is wired into. That leaves us with no kitchen and no bathroom plugs! I hung up after 35 minutes on hold. I was just trying to find a certified technician in Bend, OR. Piss Poor Products and Very poor customer service.

We got a Dacor oven and microwave wall mounted Unit 7 model DMT 2420S when we remodeled our kitchen. I have had problems with the microwave with sparking on and off. I have stopped using it as I am worried about a fire.

We purchased the modernist collections 48” range, refrigerator and freezer, oven and microwave combo and dishwasher with a kitchen remodel 9 months ago. We had one issue with the dishwasher which was resolved, then another when is stopped mid-cycle. Repairman came out and was told we needed a new panel. Found out it was back-ordered. Well, it’s now been FOUR month without a dishwasher. We have contacted customer service and asked for other options and were told there was nothing they could do! When following up we have left messages and had our calls not returned, as has our service company. I have waited on the phone 3 times 30 minutes to talk to someone, because they won’t call back. We’ve asked to talk to a supervisor, and was told our information would be forwarded... 2 days later, no call. This is by far the WORST service I have ever had for ANY type of product.

I purchased my first Dacor appliances in 1991, built a second house in 2005 and again purchased Dacor double ovens and a cooktop. Loved them! Remodeled my current home and again purchased the double ovens and a cooktop. The double oven, DTO230FS, which was installed in November 2015, 4 years ago, stopped working. I was roasting asparagus and we smelled what seemed to be burning plastic. The oven is used about 4 times a month, I have never used the self cleaning feature therefore it is surprising that it broke. The repairman said that the relay board was bad and will need to order the part. He estimates that it will be $600 to fix it. Sad that I need to incur the repair cost of an oven that is only 4 years old.

Follow-up to March 31 posting: In 2001, we installed two Dacor wall ovens and a gas (converted to propane) cook top. The cook top has been problem free and the brushed stainless steel surface still looks like new. Both ovens however, at that time, were problematic during the two year-warranty period. Knowledgeable service people were hard to come by in our region. After numerous service calls, Dacor replaced one of my wall ovens at or around the three-year mark (outside of the warranty period). That particular unit had only one minor issue since then and Dacor replaced the appropriate part free of charge. The other original unit has been problematic since the beginning. The latest problem being the internal light going on/off for no reason and then a lack of response to light button on the front control panel.Long story short, I posted my frustration here on March 31 and was contacted by a Dacor rep within two days. He asked me for detailed info on the problem and located the unit in their files. Some of the past repairs were known to Dacor, but others were not since we just did them ourselves. I was asked to send a detailed description of the current issue along with pictures, which I did. Based on Dacors analysis or the pictures and the exhibited problem, they sent me, free of charge, a control panel membrane, a door gasket and a set of door hinges. We installed these items and the unit is now in full working order.In looking back over the past years of problems with this particular unit, its clear to me the issues all stemmed from an original broken door hinge. It was compounded by the fact that the service and repair folks at the time considered the door gap to be within tolerance and we did not discover the broken hinge until the door glass shattered and we needed to replace it, which required removing the door. Anyway, at this stage in the game, I am very pleased with Dacors response. It is my impression that they are trying much, much harder to stand behind their products. So, while just a short time ago I would have never considered another Dacor product, when the time comes, they would still be on my list of considered vendors because when these ovens work, they work great.

I purchased a single wall oven in 2008 and 30 days out of warranty, the oven broke. Service required two service calls to fix the door magnets. A third visit was required as the oven codes shut down the unit. The last two service calls have been with the cooling fan. Now that the fan was replaced, the relay board needs replacement, too. I have spent $650 in service alone, which is separate from the cost of parts. There’s no help from customer service; in fact, the rep was downright rude. I will never purchase this brand again and I have told anyone who will listen not to purchase.

We just purchased our home in March of this year. The previous homeowner purchased a Dacor oven; it is electric & propane. She purchased the appliance after a complete home renovation in 2008. They lived in the home. After 1 year, they moved out and had it on the market. We purchased the home in 2012. As soon as we moved in, we noticed the oven was not working. We called an appliance repairman - $564.00 service call and part for a new relay switch. It was great; the oven worked. Not even a day later, an F1 error. We called them back out thinking they must have done something incorrectly. They then said we needed a new control panel. We did not have an additional $400.00. We just moved, so he said you could still use the oven. We did. We would use it and flip the breaker off so we did not have to hear the annoying beeping sound. Then I came home and bam - no display, no oven. We called a different Dacor certified appliance guy thinking the first company was just taking us for a ride and it was their fault. $572.00 later, we got a new control panel, but guess what, the technician did not even make it to his truck before beep, beep, F1. He came back in and then said we needed to replace the display screen - an additional $217.00 with no labor charge. We told the man to shove it. I had every plan of taking the oven to our back tank and using it for target practice. But in good business practice, since this company already invested $572.00, we could not ask them to eat the money, so we allowed a third fix of the oven. While the technician was here, the oven made a horrible loud sound and shot out flames. He insisted maybe it was due to it sitting for a week without use. He left. I never noticed this flame before when the oven worked despite the F1 beeping. Now it’s hit and miss. Some days it will shoot out a flame once until it reaches 200+ degrees and then you can hear the fan kick in. Some days, twice, I have had it happen 3 times. If my children were to open the door during this event, I am sure they would be seriously burned. At first I was thinking maybe it is normal for this oven to shoot out flames during preheat mode since after $1300.00 repairs maybe it is just not functioning correctly. But if it were a normal function of the product, to me it would do it every time consistently and not three times, or two times on some occasions. I hate to admit this but I am almost fearful of using my oven. I currently have a pie to put in for dinner and I’m thinking its 3:09 pm; I could set the oven to preheat while I run to get my kids from school so if it decides to blow up, I am not home and that is pretty sad. The last repairman we had come out said in his personal opinion, he wouldn’t have repaired the oven, because they are known for issues, and he would have gone to Lowes and spent $300.00 on any off brand stove first. We have considered that, but this stove is extra-wide and the cabinetry is built around it. So for us to purchase an oven to slide right back in it would be another $1300.00-$2000.00. We have issues with the burners not always wanting to light. I almost caught on fire lighting one because it shot out flames when it decided to finally ignite. Sometimes it just clicks. Currently, I am down to two burners when just two days ago all six were working just fine. Over Thanksgiving, it took no kidding 1-hour to cook brown and serve rolls because the oven did not reach the set temperature. We stuck my husband’s bbq thermometer to see. It was 256 degrees, not the desired 350 degrees. Does this stove have warranty? We have no clue as the previous homeowner purchased the stove. She claims to have spent $5,000.00 on this stove or more during their purchase. We do not have warranty on our home so for each repair, it is out of pocket for us, and currently we really are thinking any knock off brand at Lowes would be a better product than a Dacor oven and less of a safety hazard for our family.

Dacor double oven range turns off by itself while baking - Disappointed in Dacor, especially today. Thanksgiving 2016: baking turkey. Sill baking turkey. I dont know when the oven decided to switch off this time, but I have an uncooked turkey and guests waiting. The oven has done this before, but because it was new I thought it was user error. Nope, the damn oven mysteriously turns off on its own. Incredibly irritated with Dacor. The range hood we also purchased is a joke. We remodeled our kitchen 1 year ago and wanted quality appliances. Bad move. Save your money, folks. Save your money.UPDATED ON 03/10/2017: Dacor sent a company out to fix the broken new oven. Oven still cannot hold its temperature (It takes FOREVER to heat then loses its heat while still showing a high temp). This time I have a recording on what happens when the oven automatically switches off. Disappointing when we spent nearly $10,000 in Dacor appliances for a kitchen remodel. DACOR, please have a rep contact me!!! Still waiting to hear back!!!

Dacor ERD30S06CHLP 30 Inch Epicure Series Freestanding Dual-Fuel - I am so dissatisfied with this product. We bought the first range in 2003 and were so excited to use it. We chose Dacor over Wolf. From the beginning we had issues with the oven. It cooked very unevenly and the door never closed properly. We had a service call and they basically told us that we got a lemon. They offered us a new range for $3.5K. We thought we got a lemon so we agreed and paid for a new one for $3.5k. We also purchased the extended warranty for $2.2K.0 This one was even worse.One time I opened the oven and it burned my eyelashes. I wrote and complained with a video of the explosion and had to pay for the service call. I wrote a review in the website and they deleted it. We now own a range that we have paid over $10K that bakes unevenly, electric element does not work in oven and have minor explosions from time to time with a door that does not close. We have a few friends who have asked us about our range and we always recommend against it. We are looking for a new range. I would not recommend this range. I thought we got a lemon. But it seems thats just the product.

Dangerous condition! I purchased a Dacor 36 dual fuel range 5 years ago. I reported the issue to Dacor via email with no response from customer service. I believe the no response was an attempt by Dacor to distance themselves from their responsibility for this potentially dangerous condition. Specifics: When pre-heating the oven in convection/bake mode, if the oven door is opened before reaching the set pre-heat temperature, a ball of flame will explode up from the opened door. The ball of flame is basketball sized and has singed eyebrows and hair on several occasions. To reiterate - it is a ball of flame, not super-heated air that is the problem. As a result, after non-response from Dacor, we called a decor qualified repair technician who diagnosed the problem as a bad igniter. The igniter was replaced and the problem still exists. I fear that a small child may be severely burned by the engineering design fault.

I was and, I repeat, was a loyal Dacor customer. I gutted and rebuilt a kitchen 9 years ago and purchased a Dacor stovetop, oven and microwave. I remodeled my new house 5 years ago and again purchased Dacor stovetop, oven and microwave. Consumer reports provided favorable reviews of the appliances I purchased below.First red alert: The oven Model MORS130S and Microwave Model DCM 24S LED did not match. The microwave was green; oven was blue. The brochure was in black and white so there was no way of knowing that aesthetically they were a mismatch ... it was very sloppy(!) and very deceptive by Dacor. I mean when I waited weeks for my appliance order and the oven is already installed with a big fat ugly LED screen, what was I supposed to do, yank it out and start all over again? This was disappointing!Next, I was simmering chili on the stovetop (5 burner, gas) and, lo and behold, 18 flames started exiting through the turn knobs resulting in a meltdown. The gas was leaking through the tubes underneath the stovetop. I just happened to check the chili while I was gardening to watch the house almost burn down and btw, it was difficult to put out the flames because the natural gas was leaking under the unit. Seriously! I called customer service and they got hopping right out to fix the issue. This scared the heck out of me. It is negligent to have a product like that on the market.After about 13 months into the life of the Model MORS130S oven, the touch panel failed emitting a CO1 error message. I was told it was $140 to fix it and that the panel was defective, great quality there, Dacor. And the added joy to the CO1 error message is that the unit beeps intermittently all day and all night long unless the power to the oven is killed. Joy... now another issue - Model MORS130S oven LED lights are burning out. Seriously, what else will there be? Now its $175 for LED panel and another $100 to install by an authorized Dacor service man.So I called Dacor back again today because the LED light out was annoying me. They offered nothing. To be fair, my appliances are out of warranty but seriously, Dacor nearly burned my house down. They should be winning me back as a customer if they really cared about their customers and having long term repeat business. Never again, Dacor, never!

I purchase a home with a Dacor double oven. Unfortunately the oven begins transmitting multiple beeps and the touch panel will sometimes read off after beeping a while. I contacted the staff at Dacor requesting a service manual. They refused to send me a service manual and stated that only authorized technicians can service their equipment. Its obvious they used google or a local phone book and sent me contacts of appliance repair shops in my area.When I called, they had never heard of Dacor let alone be factory authorized. I called Appliance repair shops up to 50 miles away to find there were no Dacor Dealers. I found one 70 miles away but it was too far to send a technician. If I remove my oven from the wall and take it there they would attempt to look at it. I had to reverse engineer the thing to find that my touch panel has gone bad and now I cannot find a used one. I want to recommend that anyone considering an appliance DO NOT PURCHASE A DACOR! If you are looking for high end stick to SubZero / Wolf. Oddly enough I see that there hasnt been any reviews for the past 5 years. Maybe it appears people have stopped buying Dacor appliances.

We bought our house in 2010 and our Dacor stove was supposedly newer. When I went to clean it, I found loose screws in the bottom. Apparently, the convection element is loosing its screws and washers. Ive had this appliance fixed once already when the cooktop kept clicking. The black plastic around the controls cracked mysteriously. It takes 3 hours longer to cook a turkey than it should. This is a strange stove, which supposedly cost a lot. I wonder if a convection part missing two screws should be used?

We bought our new Dacor CPS 130S wall oven when we built a new house in 04. First we had to replace the lower heating element. Now the touchpad (Dacor part # 13290S) is malfunctioning. The + button will not respond to touch. Called Dacor and was told that the needed part number was discontinued in 2009. I double-checked with a distribution center in San Antonio, TX, who confirmed that the part is no longer available. They referred me back to Dacor on the chance that Dacor would have one somewhere. Dacors suggested solution was that we need to buy an updated completely new oven, which would cost us several more thousand dollars. So here we sit with a perfectly good oven minus a touchpad to control it correctly. So much for buying reliable, U.S. made products and receiving good service. I thought there existed a federal law that mandates a company must make parts available for 10 years if they discontinue the product?

We have a dual fuel Dacor oven purchased in 2001. We have the manual. For some reason, after cancelling a timer, the oven locked at :4. The owners manual was no help. The Dacor website was no help. We turned off the circuit breaker then turned it on again and finally, the oven worked.

I have a induction Dacor stovetop. Its stopped working and blinks an error code. Called customer service who didnt know what the code meant. I was told my model was 2015 which the rep said was old. It was installed in 2017. All they would offer was cheaper replacement parts if I paid for someone to come and figure out what the problem was and install the parts. I was told the replacement parts were not cheap though. I was told that because were the second owner of the house they couldnt fix it under warranty (even though it should be covered under warranty) because they couldnt say how it was used before (commercially or residentially). Give me a break!It gives me almost no confidence in getting this thing fixed. Warranty is a joke and customer service is terrible. So far I had to leave a voicemail for the reps next level who will call me back after the weekend. Im waiting to see what (if anything) they will do but from the first rep. I dont have a lot of confidence in their products.

My Dacor oven (DO130S, S/N V-A-10160044) is less than 18 months old. While it was in use, it popped, sparked, tripped the circuit breaker, and died. I called customer service, and voiced my concern on safety due to potential electrical defect. Steven, the customer service person advised me that this oven is no longer in warranty, and to call a repair service. I reiterated the concern for product safety. He placed me on hold, and the call was dropped. I called again, and Mike answered. I repeated the same info, and he was not willing to listen to any concerns. He hung up on me. This experience does reflect on published Dacors commitment to customer service, or product safety.

I bought a Dacor Epicure 48 range in 2003. It has never worked correctly. I read many other complaints on this same range. I had the burners replaced and I still have to light them with a match each time I turn them on. The oven temperatures were never correct. Nothing bakes properly even following their directions. It bakes very uneven. The hinges are sprung/broken (as the doors are too heavy for the lightweight hinge they use). I have had numerous service calls over the years and still not a good oven or repair. I too am very disappointed in the fact that this product is a lemon and they will not replace it.

We had a ongoing problem with a wall oven that was purchased in 2006. The most recent complaint was a oven glide rack that was not working. After complaining about it to one of their staff, they listened to our frustration and are sending us a new rack at no charge. My hats off to the great people at Dacor. Thanks for your understanding. Al

The enamel on the bottom of the top oven has blistered and the metal beneath is exposed. If the oven is heated, there is a chemical smell. This is such a dangerous situation that the ovens (double) are being removed as I write and will be replaced with a different and more reliable brand.

DCT305SNGH - I have owned this stove for about 3 years already. From the very beginning it has been trouble. The lights that turn on when a burner is on broke immediately. The place where the gas comes out and ignites is black and hard to clean. The grates are rusty, the finish has come off. The indicator knobs dont reflect what is happening in other words if it is on the lowest setting you dont have any indicator marking. It is hard to clean and scratches very easily. I have had the service person out about 5 times until they decided to send me many new parts. These arent any better. It is just a bad product. Basically the warranty is useless if you keep calling for the same issue. They say, This is the last time we will fix this issue. Sadly I always heard this was a great company and I waited 7 years to save up for this stove and boom rotten appliance.

I have had my 30 inch Dacor Dual Fuel Range since 2002. In the past month, the oven door seems to be falling apart. I had to replace the oven door handle after the handle cracked in the spots on the right hand side where the screws go in. When I tried to screw the new handle in, I noticed that the front panel on the door is lifting away from the door. It is more separated on the right hand side which leads me to believe that it is the reason that the handle cracked on that side. As a result, the handle cannot be properly installed. The only way this can be repaired is to call someone in to do it and it will either have to be glued together or the whole door would need replacing. Reading these forums, Im worried that my oven problems are just beginning and I dont want to start sinking money into this oven. I purchased a Dacor as I believed it was a high quality product and that it would be worth the money and last a long time. This type of problem should not be occurring. I do not consider 10 years a long time for a product like this. My sister has had her Jenn Air oven for almost 20 years and it has no signs of wearing out.

I purchased my Dacor wall oven in 2008 and have nothing but problems. I have had two computers replaced for over $1000 each and other boards replaced. Problems started just after the manufacturers warranty ended. I consistently get a U60 fan error message, no matter what Im cooking and no matter what cooking cycle Im on. It works for about 15 to 20 minutes and then stops and there is no way to restart or reset it.

Ive had the 27 inch double wall oven for 10 yrs. When I purchased them they were 6000 dollars. With 3 years I started having a problem with the motherboard. It has been replaced 3 or 4 times. Ive lost count. The last time they said it was fixed for sure. Well today the same issue is occurring. Im done! Never buying another Dacor product again.

I have been calling every appliance repair company authorized by Dacor to repair mystery problem. No one knows how to fix the problem, even Dacor. Both ovens stop heating during long baking times. I cannot bake anything longer than one hour, temperature drops to 290 or lower. You think your turkey is cooking but 4 hours later, it is nice and raw! Company should offer to repair or recall all stoves with double ovens.

My husband and I built our home and moved in November 2002. We purchased a Dacor Double Oven, Dacor 5-Burner Electric Cooktop and a Dacor Microwave. After the second year of living in our home, we started having problems with our double ovens. It would start beeping at different times. Sometimes it would last a few times to off and on for days. Then it would stop beeping and not return for a year. Now the beeping has started again and now it is displaying off. It wont come on. We have turned the breaker off and back on because sometimes that would reset it but not this time. Now before I could call anyone out to look at it, my 5 burner electric oven is dead. I called Metro in Tulsa, OK which is where we purchased them and they gave us the name of a repair person in our town. He came out and told us that we needed new boards for both appliances and charged us $50.00 a piece just for the evaluation. Now one week later, he is calling us and telling us that our 5 burner electric oven is discontinued! I dont want to have to purchase a new oven! I will also say that on my microwave, where the time is displayed it is blank across one line. I didnt even ask to have it look at. Please help!

I built my home in 2003 and installed a Dacor 30 wall oven. After several years of poor performance, we started to get an error message. Dacor suggested replacing a board for $300. That didnt work so they had me replace another $300 board. That didnt work so they told me I needed a new front panel and it would run about $1,000. That board is on back order and they dont have a replacement date. Thinking that its bad business to sink $1600 into a troubled product that has terrible reviews on the internet. We found out that once you go with Dacor, you need to stay with Dacor due to an unusual, nonstandard size.Thinking that Dacor has improved their product we ordered a brand new $3,000 Dacor RO130 30 wall oven. It arrived promptly and I removed the defective $3,000 oven and put in the brand new $3,000 Dacor RO130 oven. What I got was a dead brick. The Dacor customer service has been awful, and will not allow me to talk to anyone in their technical side. The oven is getting power. Dacor customer service wouldnt help me unless I could prove that the unit was getting power. So I had to get an electrician in to prove that I had properly wired the 4 cords that came off the original defective Dacor wall oven. Get service help? No chance. I live 100 miles from Seattle and no one wants to work on Dacor. So here I sit with a $3,000 brick. No service and Dacor has no clue on how they will service this wonderful $3,000 RO130 30 wall oven that is an out of box failure. I dont see how a company that has this bad of a product, two generations of defective ovens, bad customer service, reluctance from the repair community to work on their products will be in business much longer. If you are considering Dacor appliances, consider the problems that I am having. The nonstandard size of their ovens will lock you into future purchases to replace their products that dont last 10 years.

Purchased Dacor Wall Oven EO130SCH in 2011. Rarely used, so never used the self cleaning function. Occasionally wipe with microfiber cloth, eco-friendly cleaners like vinegar and Bon Ami and elbow grease. First problem in 2017 when the oven would not heat up, just before I had guests coming to stay with us. Dacor repair personnel could not make it out for a few weeks, so repaired the issue myself by resetting the thermostat with some creativity and effort. Next problem in 2018 with a U43 relay board error. Can use it for a while if turn off the power to the fuse box for a while, but in 2019 it also started making a clicking noise, and basically not functioning right before I needed it for a party. Cant replace the relay board (which costs more than $300 for the part itself) without pulling out the oven. But why is the relay board failing so quickly? Is there a fan cooling issue? Have talked to Dacor. Poorly designed, poor quality. I would never recommend Dacor.

Purchased Dacor Renaissance wall oven in July 2015, Model RNO130S. After less than a year and a half, the cooking temperature began to fail. For instance, set to bake at 425 degrees, the oven would appear to heat properly, but tried and true recipes would be pasty and uncooked at the expected time. I inserted an oven thermometer inside to test and found an erratic pattern of oven heating up properly to 425 but then sometimes dropping back to about 350 during cook time and refusing to ever reach 425 again. ABT repairman adjusted temperature calibration but refused to troubleshoot any further. Just ruined another dinner. Thanks Dacor and ABT for your unreliable product and poor service.

Im reading all these reviews and my story mirrors them all... I have actually contacted a lawyer and am considering either a lawsuit or going to small claims court because, at this point, its cheaper than continuing with repairs every other year. Has no one else considered a lawsuit under your states lemon law? Appliances are usually covered. I purchased the MORD230 wall oven in 2008... It was purchased as a second oven to my 6-burner Wolfe to cook a turkey or roast during the holidays. It has been used no more than 24 times... I have gone through 2 control panels and am now having glitches with the third. After doing a self clean recently the whole heating element blew - it will not heat at all. I am able to enter the temp but the oven just runs and runs and never heats. I have called Dacor furious for how many times this thing has broken in relation to how many its been used... They have offered parts at a reduced rate but I am not sinking another dollar in this oven on labor and parts only for it to break again. I asked for my money back and told them to come and get the piece of garbage they sold me. Do yourself a favor and buy a Wolfe... It works beautifully... My only problem was the cast iron grates rusted a bit recently... I called their customer service and was on the phone for no more than 5 minutes and they overnighted me a whole new set no questions asked! Dacor customer service has been a nightmare - so much back and forth... I tell everyone I know... DO NOT buy Dacor!!!

We remodeled our kitchen 2 years ago but didnt upgrade our refrigerator because our old one was still working. My wife and I always wanted a Dacor refrigerator. We like their design. Our old refrigerator finally died after a little a year after our reno. We were sad but happy at the same time because we can finally go buy a Dacor fridge weve always wanted. We shopped around and compared Dacor, Sub-Zero, and Thermador just to make sure Dacor is for sure what we wanted. We chose Dacor and we couldnt be happier. Its been almost a year and we still love our Dacor fridge. Now we will just have to wait until our oven dies to get a matching Dacor one.

I would never buy another Dacor product. The microwave totally crashed and now the oven will not heat. I have had contact in the past regarding repairs and they are outrageous. I plan to replace both items rather than paying unreasonable costs. Very unhappy.

Purchased Dacor Induction Range w Convection Oven RR30NIS-C in October 2013 and LOVE this range. Accidentally broke the glass on the induction cooktop with falling object mid-March 2020. Only the glass is broken, and all other electronics, induction burners, oven, etc are functioning fine. Called Dacor support to acquire part number for a glass top for repair - obtained part number #701751 superseded by #702285, BUT was informed that the part had been discontinued and is no longer being manufactured or kept in stock. No other advice was given other than to discard the entire $6000 range. Multiple phone calls with service.I asked for a listing of third party part distributors and was referred to four distributors on the Dacor public website and given no other info. I called all web-based third-party distributors I could find in USA and Canada to see if anyone had the part in stock, with no luck. I contacted two technicians to see if they would be able to obtain the part through their channels, with no luck. I am an engineer, so I spent some time pouring over technical manuals trying to find a solution to replace the entire induction range cooktop assembly (top part of the range) with a later model, and although its possible, Dacor would not provide the ability to purchase an RNR30NI range cooktop assembly that could be fit into the existing housing on top of the range. The convection oven is completely fine, and I cannot believe that Dacor has given me no other option but to pitch a six-year-old $6000 range because they stopped manufacturing one fragile part made of glass. I would imagine that many consumers may be in the same position as I, as these cooktops are breakable, and accidents happen. I have reached out to Dacor support desk numerous times without resolution, and I am at my wits end with a $6000 boat anchor in my kitchen. What a waste of money! Poorly done Dacor!I would like Dacor to provide me with some sort of solution whether it be the part required to fix my induction cooktop, or a replacement Induction Range with convection oven, or reimbursement of the purchase price so I can obtain a replacement on my own. If I am not able to find a solution to repair my range, I will never buy from Dacor again! Dacor will discontinue easily broken parts without warning! You may spend thousands of dollars and not be able to repair your appliance after warranty expires!

Motherboard on my favor wall oven has been replaced twice. Repairman said not use the self-cleaning feature as that will cause too high of heat and melt the components. Seriously, Dacor? We spend this kind of money and have these type of repair issues constantly. Just glad I finally was told what might help resolve this - I’m ready for a new oven because of all these problems.

The oven I purchased is the Dacor double oven, model number - ECD230SCH, I purchased extended warranty on the ovens. This was purchased when I bought the ovens. I have renewed this and still have a warranty for 2 more years. I cannot get anyone to do the repair on this oven. My location is at the Sardis Lake. I cannot get anyone out to service. I do not know if you have any thing to do with this. I have had an oven out since June 2013. Please help, Dacor should have service reps in this area. I am in Sardis Ms.

I had an issue with the wall oven light on my Dacor Preference double oven. To make a long story short, after contacting Dacor directly, they made sure that the unit was fixed by providing the part directly to me and confirming that the local repair company would be willing to install it. The oven is 8 years old and in the end, what I spent seemed reasonable to get a fully functioning oven (membrane switch). They were prompt, personal and courteous in their response to me. I came away feeling that Dacor takes pride in their history and their products! They also cleared up some misconceptions that I had regarding the status of their company. Although it was frustrating to have an appliance not work properly, I feel that the customer service Dacor provides makes their company one worth sticking with. That makes a big difference in todays impersonal world.

We purchased a Dacor dual fuel oven range in 2008 in conjunction with an extensive kitchen remodel. It was beautiful and expensive. It has had innumerable problems. 2008: One of the igniters broke requiring replacement. 2014: oven stopped working, required new relay board. June 2020: Relay board again broke, oven stopped working. December 2020: Oven stopped working, heating element broke. These were serious problems each resulting in 1-2 months without an oven as the parts had to be special ordered. We have not had an oven since December 2020 (it is now March 2021). We are waiting for a replacement part. In addition, minor problems included a broken indicator light and burner grating. Dacor customer service was only moderately helpful, referring us to local repair companies that had difficulty obtaining parts. Dacor has told us that this should last decades but we are seriously considering replacing it after 12 years because it is very unreliable. I would not recommend a Dacor based on our experience.

We have enjoyed our Dacor oven for a number of years but cannot recommend this brand due to high cost and frequency of repairs. The relay board, at $400 a pop parts cost only, has had to be replaced twice within 5 years. The oven door hinges failed in normal use so that the door would not close tightly and had to be replaced. The halogen oven lights fail frequently requiring replacement. Parts cost is only part of the issue. The inconvenience of not being able to use the oven for extended periods of time and high appliance repair labor costs are significant. All in all, a very good oven but reliability and frequency of expensive repairs lead us to not recommend Dacor ovens.

We purchased our home brand new in August 2006. The house was built and the appliances installed (but never used) in 2003. One of the things that sold us on the house was the kitchen being comprised of all high-end Dacor appliances (double convection oven, cooktop, dishwasher, and built-in microwave). Our excitement quickly turned to frustration. The first problems began with the dishwasher, which after several attempts at repair (circuit board) was begrudgingly replaced by Dacor, with “begrudgingly” being the key word. I have always found Dacor customer service to be rude and dismissive - with the only way that I ever received a satisfactory outcome, being via threats of contacting the BBB and Missouri Attorney General.About a year after receiving the replacement dishwasher, the internal racks began rusting badly. Once again, I called customer service who originally wanted to sell me new racks at a discount. Only after another persistent round of explaining that high-end dishwasher racks should be made from a material that doesnt rust, complaining and threatening, did I receive new racks free of charge. I was also informed that they had changed rack manufacturers and that would eliminate the rusting problem. Wrong. It has now been another couple of years, and the new racks are rusted worse than the previous ones. That is just the dishwasher.Our Dacor microwave display began slowly losing its LED display about 2 years ago. Lately, the microwave interior lining is beginning to disintegrate and rust through. One of the burners on our gas cooktop makes a constant popping noise when lit. The top half of our double convection oven no longer heats beyond 250 degrees. I realize that our appliances are now significantly beyond their warranty period, so I am no longer even attempting a resolution through Dacor. I will most likely ride these appliances into their graves and replace them with another brand. I am writing this mainly to alert others about my experiences with what I believe to be Dacors total lack of quality at a premium price. In my opinion, Dacor is all style and no substance.

I purchased all Dacor products. First Dishwasher went out, had purchased warranty. Came out 6 times to fix it, filed complaint with Better Business Bureau. Finally got dishwasher replaced with a Kitchen Aid. Thank God for the BBB. They help people. Then my stand alone range with 6 burners had one of the burners go bad, the appliance co. fixed it. Then the oven relay board went defective. Had to order part over $400.00, no warranty. Then wall oven Relay Board went out, 2016. Paid over $460.00.Less than 12 months later relay board went out again. They said Sorry, no warranty. Ordered part said it was $500.00 + to replace. The appliance repair tech ordered wrong relay board. They called me today and now said its going to cost $650.00, no warranty. Do not buy Decor products. They are horrible. I feel I am being ripped off by Dacor and feeling untrusting of the Appliance Co. I may need to file another complaint with Better Business Bureau. Buyers beware!