Con la incorporación de esta instalación de 398,000 pies cuadrados en 2016, Flash Furniture ha podido aumentar en gran medida la amplitud de su oferta de productos. Ubicados estratégicamente para dar servicio a todo Estados Unidos, ambos almacenes son instalaciones de muelles cruzados de clase A de última generación con 96 puertas de muelle.

Calentador de patio a gas Códigos de error

Problem: The burner will not light.  
Possible Reason: The burner injector is clogged.  
Possible Solution: Clean the burner injector. 

Problem: The burner will not light.  
Possible Reason: There is low gas supply pressure.  
Possible Solution: Call your gas supplier. 

Problem: The burner flame goes off immediately after ignition. 
Possible Reason: There is low gas pressure.  
Possible Solution: Call your gas supplier. 

Problem: The ignition is delayed.  
Possible Reason: The main burner carryover ports are clogged. 
Possible Solution: Clean the main burner ports. 

Problem: The ignition is delayed.  
Possible Reason: There is low gas pressure.  
Possible Solution: Call your gas supplier. 

Problem: The combustion on the burner is inadequate. 
Possible Reason: There is not enough air.  
Possible Solution: Check the air passageways and burners for dirt and debris, and clean with compressed air. 

Problem: The burner flame is low.  
Possible Reason: The supply hose is bent or twisted.  
Possible Solution: Straighten the hose and perform a leak test. 

Problem: The burner flame is low.  
Possible Reason: There is blockage in the burner injector. 
Possible Solution: Clean or replace the burner injector. 

Problem: The emitter glows uneven.  
Possible Reason: There is blockage in the burner injector. 
Possible Solution: Clean or replace the burner injector. 

Problem: The emitter glows uneven.  
Possible Reason: The base is not on a level surface.  
Possible Solution: Place the heater on a level surface. 

Problem: The emitter glows uneven.  
Possible Reason: The gas pressure is low.  
Possible Solution: Replace the cylinder with a new cylinder. 

Problem: There is slight smoke and odor during initial operation. 
Possible Reason: This is residue from the manufacturing process. 
Possible Solution: This will stop after approximately 30 minutes of operation. 

Problem: There is thick black smoke.  
Possible Reason: There is blockage in the burner.  
Possible Solution: Turn off the heater and let it cool. Remove the blockage and clean the inside and outside of the burner. 

Problem: The heater produces a whistling noise when the burner is lit. 
Possible Reason: Air passageways are blocked.  
Possible Solution: Check the minimum installation clearances and air passageways for debris. 

Problem: The heater produces a whistling noise when the burner is lit. 
Possible Reason: There is air in the gas line.  
Possible Solution: Operate the burner until the air is completely purged. 

Problem: The heater produces a clicking noise just after the burner is lit or turned off. 
Possible Reason: The metal is expanding and contracting. 
Possible Solution: This is common with heaters. If noise is excessive, contact a qualified service person. 

Problem: There is a gas odor even when the control knob is in the OFF position. 
Possible Reason: There is a gas leak.  
Possible Solution: Locate and correct the leak immediately. 

Problem: There is a gas odor even when the control knob is in the OFF position. 
Possible Reason: The gas control is defective.  
Possible Solution: Replace the gas control. 

Problem: There is a gas odor during combustion. 
Possible Reason: There is foreign matter in the gas or on the burner ports. 
Possible Solution: Check the gas passageway and burner. 

Problem: There is a gas odor during combustion. 
Possible Reason: The heater is burning vapors from paint or impurities in the air. 
Possible Solution: Stop storing and using odor causing products near the heater. 

Problem: There is a gas odor during combustion. 
Possible Reason: There is gas leaking from the regulator and hose connection, the valve and pipe connections, and the pipes. 
Possible Solution: Locate and correct the leaks, or contact your gas supplier. 

Problem: There is carbon build-up.  
Possible Reason: There is dirt or film on the reflector and flame screen. 
Possible Solution: Clean the reflector and flame screen.