Si está buscando ayuda para arreglar su Dishwasher Hisense, ¡no busque más! Nuestra guía completa de códigos de error del Dishwasher Hisense explicará problemas comunes, brindará consejos y le mostrará cómo leer los códigos de error de su modelo.

CODE: FA 
PROBLEM: Aquastop Failure. If the Aquastop contact on the bottom tray of the appliance is closed for more than 30 seconds an Aquastop Failure will be detected. In an Aquastop condition, the Door will remain locked, and the Drain Pump will run constantly

CODE: F04 
PROBLEM: Too Long Heat Time. If the water temperature is not increasing over 35C during 40 minutes of the first heating step in the cycle the CCU will display this Error.

CODE: F05 
PROBLEM: Water Temperature Sensor Error. If during the water heating in the wash cycle, the water temperature sensor (NTC) value is out of range, the ''F/05'' error code will be displayed. Check the water NTC resistance or Check connections to the NTC and CCU.

CODE: F06 
PROBLEM: Drive Motor Tachometer Error. The control is unable to properly detect motor speed (several times) and the machine will shut down. If a failure occurs during high-speed spin the door will be unlocked after when the drum stops rotating.

CODE: F07 
PROBLEM: Motor Control Triac Error. The main control has detected a short circuit in the motor control triac. If a failure occurs during high-speed spin the door will be unlocked after the drum has stopped rotating. Check CCU by running Test Program.

CODE: F08 
PROBLEM: Heater Circuit Error. The main control has detected a heater circuit failure. These failure modes are checked before the cycle starts and after the spinning steps.

CODE: F12 
PROBLEM: Heater Circuit Error. The main control has detected a heater circuit failure. These failure modes are checked before the cycle starts and after the spinning steps.

CODE: F13 
PROBLEM: Door Open LED flashing after the cycle is started. If the CCU is not able to lock the Door of the washer after the program starts within 10 the Door Open LED will flash for 10.

CODE: F14 
PROBLEM: EEPROM Error. The Central Control Unit (CCU) receives its data from an EEPROM onboard the CCU. If there is an error reading this data it will cause this error.

CODE: F15 
PROBLEM: Drum Up Circuit Missing ( Only for TOPLOADERS with DRUM-UP Circuit). If the CCU is not detecting the Drum Up switch closing during Motor rotation this failure is displayed. This Error is detected ONLY during the Service Program.

CODE: F21 
PROBLEM: User Interface Error ( detected only with Smart user interfaces). If the communication between the user interface module and CCU is disturbed this Error is displayed. If the failure is displayed on the digits the display module is not able to ''talk'' to the CCU. If the failure is displayed on the status LED the CCU is not able to contact the Display module.

CODE: F23 
PROBLEM: Press switch Failure. If the CCU is detected during the wash cycle that the press switch contact for the wash level and the press switch level for the heater safety is ON simultaneously for 10'' this failure will be displayed.

CODE: F24 
PROBLEM: Overflow Failure. If the Overflow contact on the pressure switch is Closed for more than 60 seconds an Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly.

CODE: F26 
PROBLEM: Pump Driver Failure. If the CCU detects during the wash cycle that the triac of the pump is defective it will display this failure. Check the resistance of the press switch contacts.

CODE: F27 
PROBLEM: Reversing relay failure. If the CCU detects that the motor is possible to rotate only in one direction this failure is displayed. Check the CCU.

CODE: F28 
PROBLEM: Tapped Filed Failure. If the CCU is not able to switch ON the tapped field of the Motor this failure Code is displayed.

CODE: Fod 
PROBLEM: Some foam was detected During the Wash Cycle. If the CCU is not able to drain out the water after washing or not able to spin after several trials this alarm Code is displayed.

CODE: UnB 
PROBLEM: Unbalance Error. Cause: The load is too small. The appliance is tilted. Laundry is gathered to one side. Nondistributable things are put into the drum.

SOURCE: finderrorcode.com

Páginas de códigos de error relacionados:
Hisense Television Códigos de error, Hisense Refrigerador Códigos de error, Hisense Distancia Códigos de error, Hisense Lavaplatos Códigos de error,

Páginas de resolución de problemas relacionadas:
Hisense Television Solución de problemas, Hisense Refrigerador Solución de problemas, Hisense Distancia Solución de problemas, Hisense Lavaplatos Solución de problemas,

Páginas de reparación relacionadas:
Hisense Television Refacción, Hisense Refrigerador Refacción, Hisense Distancia Refacción, Hisense Lavaplatos Refacción,

Páginas de piezas relacionadas:
Hisense Television Partes, Hisense Refrigerador Partes, Hisense Distancia Partes, Hisense Lavaplatos Partes,

Páginas de precios relacionadas:
Hisense Television Precios, Hisense Refrigerador Precios, Hisense Distancia Precios, Hisense Lavaplatos Precios,