The original Sun Glo patio heater was designed in 1961 by Edwin Cowan, a leading U.S. infrared heating appliance engineer. A unique demand existed in California for decorative, yet practical, gas fired heaters. Cowan pioneered and developed the circular radiant heater concept primarily for use in country clubs, hotels and restaurants.

Calentador de patio a gas Reparar

For the home, kitchen and beyond, SunGlo manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of SunGlo appliance repair from experienced professionals, your local Appliance Helper can help.

Starting issues or reduced heat production
Outdoor furniture and fixtures accumulate dust, dirt, and debris. When these elements stack up on a patio heater’s gas or electric heating element, the heater may have starting issues or reduced heat production. If your patio heater has these issues, cleaning it could be all you need to do.
To clean the burner or heating elements, remove the emitter screen to expose the burner or element. Because these should be kept dry, use compressed air to blow off dust and dirt instead of a damp cloth. Reattach the screen.
To clean a gas burner’s individual ports, remove the emitter screen and take a pipe cleaner or straw brush to remove dirt and debris. Once clean, reattach the screen.

Gas heater doesn’t stay lit or heat production is reduced
A gas patio heater requires proper gas pressure to function properly. Without it, the pilot tube and burner may not receive enough gas to keep the heater lit, or the burner’s flame and heat production will be reduced. Low gas pressure is usually caused by broken, kinked, or otherwise damaged gas lines.
To fix damaged gas lines, first visually inspect all the heater’s gas lines, inside and out, that connects to the primary gas source. Kinked lines are easy to spot, but cracked or broken lines that produce leaks may be more difficult. You can use a leak detection spray to make leaks more visible.
Any damaged lines should be replaced. To do this, use a wrench to loosen and remove both ends of the gas line connections. Then connect both ends of the new gas line to the heater and tighten them with the wrench.

The burner goes out after a few minutes
The thermocouple of a gas patio heater is a safety component designed to prevent gas leaks when the pilot goes out. It’s a copper rod that sits next to the pilot tube on the other side of the spark igniter; it allows gas to flow through the pilot tube when it detects heat from the pilot light.
If the thermocouple is too far away from the pilot tube, it can’t detect the heat and will restrict the gas supply. Free-standing portable units are most prone to this malfunction because the thermocouple may be bumped or wiggle out of place while the heater is being moved.
To fix a thermocouple that’s too far from the pilot light, remove the emitter screen to expose the ignition housing. After locating the thermocouple, use pliers to gently squeeze the thermocouple and pilot tube closer together. Reattach the screen.

The propane igniter won’t fire up the heater
Many gas patio heaters are equipped with a spark igniter (a.k.a. sparker), a small electrode that ignites the pilot light to get things started. Over time, spark igniters fail. If you can successfully start the heater with a match or lighter, the igniter is probably the problem.
To test the spark igniter, use a screwdriver to remove the screws holding the screen around the main burner (a.k.a. emitter screen). This will expose the ignition assembly, which consists of the spark igniter, pilot tube, and thermocouple. Hold down the ignition switch to visually inspect for a spark. If no spark is detected, you may need to replace the igniter.
To replace the spark igniter, note that it is usually secured to the ignition assembly by a single retainer nut that can be removed with a wrench. On the other end, it’s usually linked to the ignition switch wiring with a push-in connector that can be easily pulled out by hand. Once you remove the old spark igniter, simply reverse the process to install the new one. 

SOURCE: https://www.familyhandyman.com/article/patio-heater-repair-tips/#patio-heater-troubleshooting