I bought a JVM3670SK05 a little under two years ago. It is an above the cooktop vent-a-hood microwave. I believed I was buying a quality unit. Now everything is working, but there’s no heat! Even the cheap units from Walmart work longer than this expensive piece of crap! Now I either have to spend enough to buy a new hood for cooktop and new microwave or pay the same price and buy parts in hope that they will not go out again. Not really feeling lucky with the GE product.

We purchased a GE Model JVM 3160DF3WW microwave oven in October 2016. The handle broke on this unit the first week after we bought it. It then worked fine for 10 months. In August 2017 it began throwing the circuit breaker erratically, then whenever it was turned on and has not worked for a full day since. It has been repaired by Appliance Solutions of Utah at least 6-7 times (by two different technicians) and still has not worked. At least $500 worth of new parts have been put into a $200 microwave by them. After numerous calls to GE, they have offered to send me a Goodwill Certificate for the amount of purchase after I buy another GE microwave. With our experience with this microwave (inoperable and unrepairable for 5 months) I dont intend to buy another GE microwave; especially considering the one available locally is the exact same model as the one we have, which was purchased, from Sears, for $191.42. Appliance Solutions of Utah has all the records of the NUMEROUS unsuccessful repair attempts made on the unit since August 2017. I requested a refund so that a different unit could be purchased. Over the course of the past 5 months I have talked to at least four different customer representatives, after multiple hours on hold. None could find any record of the previous discussions. GEs final suggested solution was to offer us a $100 Goodwill Certificate, the title in itself being ironic. So, after buying a microwave which was defective in the first place, spending $75 to have it installed, being without the use of the microwave for five months, and being told that, GE does not offer refunds, that is what the company feels they should do to rectify the situation. Setting aside an implied warranty of fitness, the fact that the repair agents sent out by GE could not repair the microwave after numerous attempts would seem sufficient grounds to fully refund the purchase price. That is the least a reputable company would be expected to have done. GEs position is that the store selling the microwave would be responsible for a refund; apparently ignoring the terms of the warranty. I this point, I am considering filing a complaint with the Better Business Bureau and a claim in small claims court for Breach of Warranty. Obviously, the microwave was never repaired per the terms of the warranty as it is still inoperable and has never worked since the initial report to GE. We will NEVER buy another GE product; Buyer beware!

From these posts, Ive seen people saying that they couldnt trust GE American-made anymore. Our microwave oven was made in Malaysia, but GEs home office appears to be in Louisville, Kentucky. Our problem: peeling paint on the door and upper part of our 2009 GE #JES1451DN1WW oven. As a cancer survivor of 8 years, my antenna goes up with any defaults such as this. On a common sense scale this should never be happening. I was very sad to see no recalls on these items Ive been reading about and am frankly scared to use this microwave. Shame on you, GE.

Microwave and convection oven together...perfect for heating food or baking. Very easy to operate. G.E.profile. Mounts over the stove with an exhaust fan and lights. Also has a rotating plate in it to heat evenly.

I have a new GE profile model PDWT380VSS - Two in fact. The first one kept breaking glasses in the top rack. GE technicians could not find an answer so they replaced the Dishwasher. Now six months later its doing it again. This replaced a perfectly good, older model as part of a remodel. Theyll be sending another tech who I suspect will not have an answer. Any thoughts on what could be causing this or a way around it or is it to be expected? The first GE profile I had for several years with no such issues.

Purchase a GE microwave Jes1142sp2ss on December 2014 from BrandsMart. The paint on the bottom of the microwave is peeling off exposing the metal. I have never ever heard of this happening on a microwave. I will never buy another GE product.

The GE microwave installed in my new home caught fire on its own. It is less than 3 years old. GE Consumer Relations Department refuses to replace it for free even when it caused a fire accident on its own. GE microwave failed in its safety standards. GE also has failed in its Consumer Relations. I will not trust GE brand again.

I have a built-in GE microwave. It is easy to use and best of all very easy to clean. It is brand new and stainless steel. Looks nice on the wall above the built-in GE oven. I can easily reach it. Some built-in microwaves are too high.

Hello to all reading this and considering purchasing a GE dishwasher or other appliance from them. Last June 27th we bought a new home which came with all GE appliances. In fact I have 2 of these dishwashers. Once in the basement (just for low usage) and another one in the kitchen. The first day the dishwasher in the kitchen did not work and they came out and replaced it. I have had 3 other service calls on this thing and now it does not clean. Six days before Thanksgiving. I called and the lady told me no service until November 30th is available. It does not work, the first time they came out it was for a leak, second time the pump was not working and the dishwasher was not draining and now it is not cleaning. It was almost as it was my fault. It is a dishwasher - you put the dishes in and then turn it on and they should come out clean. I should not have to rinse or do anything special to make it work. We spent over 1500 dollars on each of these dishwashers and now one if not working. I did not do anything other than turn it on and expect that it should clean.I was told that they would sell me another dishwasher at a discount. DO YOU REALLY THINK THAT I WOULD EVEN CONSIDER ANOTHER ONE?! A real company should replace this POS and give me another one for free and it has been 15 months and I have had 2 of them in my kitchen. I can tell you if you plan on purchasing look at KitchenAid they run forever without any problems. They also did a fantastic job of support (I had it for 6 years in one house with one repair, second house they never needed to come).

This is a work horse of a machine. I have been using it for 12+ years. Not my first choice, but it was here when I moved in. Still going strong. So why change now, when its doing its job. My first dishwasher choice would have been a Bosch, because they are so quiet.

We purchased a manufactured home that had brand new, GE appliances in it. We have been in the home for almost two years, but the dishwasher has never worked well, at ALL, even when it was brand new. We called GE and they sent a local appliance repairman to our house. He said that there was nothing wrong with the dishwasher. They are just junk. Amen! I have tried running the water in the sink until it is hot before the dishwasher fills up, we have tried using a citrus additive that is supposed to help it clean better, we have tried several different kinds of soap, NOTHING works. It never gets the dishes clean, there is always residue and food left at the bottom of the dishwasher, and it runs for hours on end. I cant wait until I can get rid of this pile of junk and purchase a Whirlpool or anything else. I will never purchase GE appliances, EVER!!!!

Had model JES1460DS3BB less than 2 years. I started to smell burning plastic when using it. Research tells me the wiring is burning up. Im sick and tired of GE appliances. Ever since my GE toaster caught on fire in 1969 Ive had bad luck with GE. I gave the company another chance when I bought this microwave. I will never buy another GE appliance - large or small.

I have an above range GE Microwave - it is not even 2 years old and it is done. I noticed the past few months it was not heating properly - it needed more time. This week it just blew out! NO more GE Microwaves. I have a refrigerator and I am wondering how long that will last. Thank you!

I purchased 5 new GE Appliances delivered June 1, 2014. Within the first 2 weeks, the dishwasher wouldnt drain and had the repairman out to fix it. Within the next 2 weeks, the door wouldnt stay closed and had the repairman come. He took the rubber off around the door so that the door would close and said he was not familiar with GE dishwashers and would go to showroom and look at it and come back. I said as long as I dont have a flood. He assured me that the water only fills up so far and would not leak. Within the next 2 weeks, I was downstairs and heard water running and it was pouring through the ceiling. I ran upstairs and very hot water was all over my kitchen and pouring through the floor into the basement. The unit malfunctioned and wouldnt shut off. I had to shut off the water to the DW and run to the electrical panel to shut off power. I then had to call insurance to get a restoration company to dry out and fix my house. I phoned Arkona Appliances to let them know and they gave me a toll free number to call for GE. The toll free number when you call you are on hold for at least an hour to talk to a receptionist which puts you on to someones voicemail. I was on hold for one hour the first time and one hour and eleven minutes the second time and begged to get a direct line for future calls. Reluctantly, the receptionist gave it to me. The technician had to come out and assess the dishwasher and said I needed a new dishwasher and sent the report in Friday, August 1. Because of the long weekend, I waited to call until Wednesday and they said they didnt receive the report. She asked me whether it was emailed or faxed - how would I know. Then she found the report and said I would get a new dishwasher Wednesday, Aug 13 or the 20th. Still havent heard anything. If received next week, it will have been 5 weeks from the time of the flood I have been washing dishes by hand. Awful customer service from retailer as well as GE. Problems dont go away they just get worse. Initially upset - NOW I AM FURIOUS!!!

Worst dishwasher ever. No matter all tried it just does NOT get all off dishes. Have to hand wash too! IS just not made to do the job. Just relying on GE reputation of the past! Made a mistake believing General Electric hype advertising. SAD.

Started at the front rack hook. My wife stopped the microwave immediately, luckily she was right in front of it when it happened. This is a serious condition that could destroy a kitchen or even the house. I will call GE Consumer hotline tomorrow.

I am rating my over the counter GE microwave model no. JVM3160RFSS. Ive had it for over 2 years and its still performing well. Pros: Solid feel, sturdy door mechanism, easy to clean interior, attractive design, fairly quiet, adequate lighting inside, reasonable price, fan works okay for moderate smoke, short reheating times for lighter fare, cooks frozen foods quickly. The integrity of the interior is good with no chipping or cracking. Cons: Fan is inadequate for heavy smoke if searing beef, hot and cold spots while reheating heavier foods such as mashed potatoes or casseroles, controls are hard to see in dim or moderate light. A suggestion to GE would be to make microwaves with optional backlit buttons to see at nighttime or in dim lighting. I like that GE manufactures most of their microwaves in the United States.

Two years less three weeks after we started using the dishwasher in our new home the plastic at the top of the door where all the buttons are cracked. So far it hasnt interfered with the way its working, but were on alert that it might not be too long. Ive owned dishwashers before, one for 32 years, one for 9 years. There is no acceptable reason for there to be a crack in less than 2 years. This, coupled with a refrigerator that had a broken drawer in 13 months, I will NEVER buy another GE product again!

I purchased a slate dishwasher in Oct, 2014. After the third cycle the soap would not dispense (door would not open) or the soap dribbled out and remained running down the door. I had to run the cycle twice to get the dishes clean and for the soap to dissolve. I called the store at which it was purchased. A tech came out and replaced a part. Did not work. After the second time, when the tech said nothing was wrong, even though he saw the soap running down the front door, I called GE. They sent a tech from a different store. After the eighth repair I told them I wanted it replaced. They had already replaced the soap dispenser twice, the control board and even told me to move the baskets (ridiculous). They also suggested I run hot water before the cycle! They said if it was repairable they could not replace it.We went back and forth with this and they finally agreed to replace it. Got the new slate dishwasher in July, 2015. After two cycles I started having the exact same issues! I will not deal with GE or ever buy another of their appliances. I will tell everyone I know not to deal with this company. Quality is terrible and service was extremely frustrating, having to take off work numerous times and wait hours for the service person. In the end, it never worked!

I wish I had found this complaint section before I purchased my microwave. Bought model HVM1750DP1CC in May of 2010. Now, 3 years later, all of a sudden theres no power to the unit. The wall outlet is fine. There were no storms around here when it went out. It just seemed to fry itself! The repair/troubleshooting instructions tell you to get a licensed technician to check this and check that because of the voltage. They give you a flowchart to troubleshoot it yourself, but no pictures to go with the diagram. Sure I can check the fuses, if I knew where they are!GE - NEVER AGAIN FOR ME. Wish we still had good-valued products Made in the USA. This one is made in Malaysia. NOT WORTH IT. Time to sell the GE stock too. Their products suck and class action suits will probably follow. Kris is Pissed!

I know this commonplace complaint, like thousands before me, will head straight into the wind because the world just works in this way: technical support and repairs works as a profit center for a corporation. My GE Profile microwave abruptly failed out of warranty after years of use. The cause was due to a wire burning up inside that had not been loosely connected, said the GE technician, so this was an issue of inadequate quality--not bad enough to cause the microwave to fail quickly but enough to cause failure over time.After taking the microwave out of the built-in cabinet, it only took the technician about 5-8 seconds to find and diagnose the problem, several minutes to get the right part (a wire) from the truck, and a couple of minutes to fix it. The labor charge was $121 for about 7 minutes of repair work, to be liberal with time. (This charge is separate from the charge to come to our home and diagnose the problem.) This prorates to over $1,000/hour for a basic wiring change, which I think is exorbitant. I understand that the technician is a highly trained individual, but this is already reflected in the high labor rate.According to GE, the cost to replace the built-in microwave, which came with a matching stainless steel frame would be $550 if we wanted the new microwave to match the frame at least (but not necessarily the oven, stove, etc.). This is the kind of cost you dont think about when you buy a new home built with matching appliances--well, I didnt. Companies like GE can rationalize all they want about all the overhead associated with servicing a repair call. I can certainly grant them some leeway, but in the end, charging an extra 8 times more an already high labor rate given the time needed to fix the problem is simply price gouging a consumer who has no good recourse. (This is why I pretty much avoid repairing anything, except for my car. Its almost never worth it.)I recently had an experience with an experienced plumber charging an hourly rate of $150, prorated by and rounded up to half-hour increments of work, regardless of difficulty of work. Repairing an appliance should work the same way, and my GE bill would have been halved. Because of such profiteering, I will not consider purchasing a GE appliance in the future. I pray that this microwave doesnt break down again in the coming years due to some other problem. It would be a lot less expensive to just buy a non-matching portable microwave then for $100-$150 than to keep up appearances.To be fair, the woman who fielded my service call was courteous and empathetic. Because the microwave apparently had an electrical burning problem, she previously waived the diagnosis fee. Otherwise, my simple repair would have run several hundred dollars, more than the cost of the microwave. However, she was unwilling to reduce the labor charge, so based on how strongly I felt ripped off, I give GE a star rating overall.

Outstanding value and deal the price for this unit was the best one I could find it’s small simple to used and fit in my kitcjechm area like hand in glove I purchase then as matching pair for 429 dollars each all I needed for my new home and they are not bad looking at all,simple set up and great functionalities for the money no complains so far they get the job dome nicely thanks Best Buy’s for sucke great deal and quick delivery

Bought a GE microwave and arranged to have it installed. Kept it in sealed box for 3 days until installer appointment. Opened box to find a crease (dent) in door. I phoned in to the GE warranty depot and they informed me that I only had 48 hours to report and as such was out of luck. They indicated that it is clearly stated in the Appliance Manual under the warranty section. Too bad that the Manual was in the sealed box. No warning on the outside of the box. On top of that the individual that I spoke to at the Warranty Depot was very rude. No more GE Appliances for me. Be forewarned.

Almost 2 years ago and right from the start this dishwasher did not clean. Numerous times they had people come out and supposedly fixed it. Ive had different suggestions as to what to do. 1. Turn on the hot water tap and make sure its hot. 2. Use various different cleaning solutions on top of the dishwasher soap. 3. Use loose detergent.4. Throw at the bottom of the washer.One of the arms keeps falling down. And the last time I was told I could return it and get a deal on a better machine. I am now left with hand washing every item that goes into it unless I want gritty glasses, dishes and silverware. I bought this at Home Depot. I will never buy any products such as this from them nor will I ever buy another GE product.

I purchased the model (PEM31SM1SS) GE Profile (Spacesaver oven) in November of 2008. Less than a year later, it overheated and failed. Since it was still under warranty, the repair was managed by the appliance vendor. The scorch mark on the rear wall of the oven was and is still there. During the past year, the paint on the interior roof began to bubble and peel. There is now a broad area of exposed metal and the paint around the interior door frame is also peeling. When I returned to my vendor, I was informed that several other customers had the same issue and was told to call GE. I also checked online and found many other complaints for the same thing.When contacted, GE offered me a $75 rebate voucher, applicable only if I buy another GE microwave. The current price for this model - the only one anywhere that fits the space - is $279. Even with the voucher, this is still a lot to pay for a product that has proved to be defective. GE does not appear to stand behind its products. It used to be a reliable company but given the issues Ive had with both this microwave and my expensive dishwasher, I will be looking elsewhere in the future.

Even though the dishwasher was bought 15 months ago, it was only used for the last past 5 months. There is no water fill up the washer. When I call GE for the service, the operator keeps saying that it is out of one-year warranty and I have to pay everything to fix it; I have proof that the product was in use under 5 months. The product clearly has a problem. I am not happy with their services and with the product.

In late March, we placed a service call under GEs one year warranty. The outcome - a gasket repair. Within a week or two, the door began to drip from both the right/left bottom. With having three teens, I figured someone opened the door and released some water. Well, that just wasnt the cause. Shortly over the next few days, the leak was consistent and I placed a service call to GE on 4/19. The customer representative offered, instead of a service call, to order some panels that fit it the bottom of the dishwasher. I stated clearly that our one year warranty was up on 4/25 and if this does not work, would GE address the issue with a service call? Answer was yes. Within a few weeks, I began to worry when I did not receive the panels. A call to GE was made; however, no documentation was noted of the call made on 4/19. However, GE stated the information might be in parts department, but regardless now, that call was made after one year warranty, extended warranty would fix the issue. Long story short, the extended warranty states problem initiated under GE and GE states the extended warranty is responsible because the call was made outside the one year warranty. I expressed that GE never fulfilled responsibility as GE did not even notify us that panels were not available for our unit. In the meantime, I am the one out of a working dishwasher. Now I know $539 may not be a lot to invest, but we feel the loss. The frustration and lack of responsibility to correct the repair is just beyond me. GE is responsible. Oh and did I share that lack of communication with GE is horrible? A promised call within 12-24 hours just doesnt happen. Again, I know most would say its not worth the frustration, but it makes me sad that GE and Assurant Warranty company can get away with what I know is wrong. Weve learned from this ordeal. No more GE products in our household.

This washer was easy to install myself, and has worked perfectly. Stainless steel insides. Very happy. You put a pod in, turn it on, cleans great. We do not even have to use heating element. Dishes dry quickly on their own. 24-inch wide. Bought to fit the new kitchen cabinets. Nice brushed stainless outside. Cleans easy with towel and hot water. Silverware container picks up to take to storage areas. No problems at all.

I bought a new house and within 2 years my GE dishwasher and now my GE microwave jvm1750sp1ss need replaced. Ive got a cheap $100 microwave in the basement thats worked for years. GE quality has apparently went downhill. NEVER again. Cannot believe appliances that cant even last 2 years.

My husband ran our 4-year old GE stainless steel dishwasher (PDW8980N00SS) at 9 pm, 2/4/13. At 11 pm, he emptied and put away the dishes. At midnight, we went to bed. At 4:50 am on 2/5/13, we were awakened by a burning smell and discovered the heating element of the dishwasher either turned back on or never turned off. We were unable to touch the granite counter, the front of the dishwasher, and both wooden cabinets on either side of the dishwasher were very warm. The spinning arms and other plastic parts were melted. The only way it could be turned off was to unplug it from the outlet in the cabinet. We were leaving for the airport at 7:30 am on 2/5/13, so needless to say, we would have lost our home if this occurred a couple of hours later. The Assurant tech said it was repairable and ordered a part, which would take at least a week. Assurant customer service had us call GE. When we stated we didnt want the faulty dishwasher repaired, but wanted a new dishwasher, the best the GE customer service rep could offer us was 38-40% off several new different Profile dishwashers. After reading page after page of bad reviews, most of which detail either one or multiple fires from different GE dishwashers, we dont even want another GE dishwasher in our home. We already needed the smart soap dispenser replaced, since it clogs periodically and doesnt wash dishes very well. We also have a countertop GE Profile microwave, and the turntable motor has gone out 3 times so far. Weve purchased the replacement motors ourselves since it isnt under Assurant insurance. Not sure what the resolution will be on the dishwasher, but wed be happy if GE would give us at least $500 toward a different brand dishwasher. I know well never ever buy another GE appliance after this. We wouldnt sleep at night or ever want to go out of the house without unplugging another GE dishwasher, so dont want one.

Microwave lasted 6 months, very light duty, burnt metal smell. Purchased from Walmart, they told us to contact GE. All GE could offer is a Good Will certificate which means, we have to go buy another GE microwave up to $155 in value. We pay taxes, shipping etc. Not really a customer-centric return policy for a lousy designed product made from cheap components in Asia. These microwaves are a piece of junk. This isnt the only complaint about this model of microwave. Others are experiencing the same problem all within the past 6 months. From March 2018 thru August. Stay away from these microwaves.

The way you put bowls in this model doesnt allow for cleaning them completely. You must wash the bowls AFTER cleaning them in dishwasher. Waste of time & money. Capacity smaller, noise louder. Not good value.

I received a recall on my original wall oven with microwave unit, and was only going to receive financial help from GE, if I replaced it with the same unit model JTP90. The unit was only 3 years old at the time. I purchased the new model, which cost $1,200.00, and received a check from GE for $600.00 for the recall, which is already a rip off in my opinion. I had the new unit for 14 months, when the microwave stopped working completely, with no power whatsoever. I thought it had blown a fuse. I took it to the repair center, and they tell me the diode, capacitor, and fuse have all failed. $200 later, it can be fixed, but they have no idea why all three went out at the same time. I, however, do know, GE just makes junk! I will never purchase another GE appliance. Just a side note, my 3 year old dishwasher was also recalled, and it was $600 to replace it with the same model. They sent me a check for $300. It sounds like GE has a good thing going. Make a piece of junk and recall it a few years later, and only give the customer half of the cost to replace it, and only if they buy another GE product! Wow!

This is one hell of a dish washing machine. You really need to think about getting in on this thing at the ground level. You put the dishes in dirty and they come clean! Holy**!

I bought a GE Adora dishwasher from Home Depot. There is nothing technically wrong with it - in other words - it is not malfunctioning. It is just that its normal operation is AWFUL, in my opinion. The PROS: it is very quiet. The CONS: it does not clean your dishes! And since this is the primary function of a dishwasher - I would say it is a complete failure. Originally, I had hard water, and I thought that was probably the issue. I purchased a whole home Kinetico system, which remove almost all particulates from the water, and makes bottled-water-quality drinking water. (On a side-note, I would TOTALLY recommend the Kinetico system!) But even after having the water issues fixed, the dishwasher has NEVER worked properly. I have used every type of dishwasher detergent, including Cascade Complete & Platinum, Finish Ultra & Quantum Powerball... and I have also added rinse agents etc. Basically - whatever state your dishes are in when you put them IN the dishwasher, they will only be slightly improved when you remove them. Even if you SOAK the dishes first, they come out with all kinds of residue. It does an especially horrible job on glassware, but silverware is also terrible. And I have to re-wash by hand every coffee cup that comes out. I truly loathe this machine, and will replace as soon as I do enough research about a better brand & model.

I was heating up some Mexican food and smelled plastic burning and looked in the microwave and saw one plastic knobs that hold up the metal grill on fire. I blew it out. I have GE repairman come out to see if they could fix it, and he said that happens and they were not responsible for it. I told the repairman to get out of my house as GE has built a product that can burst into flames and will not address that they are at fault.

GE microwave model JES1344ES. This is a stainless steel with black accent 1.34 cubic foot microwave oven. It looks great. The micro is heavy for its size. The stainless steel is brushed and low luster finish. The door handle is chrome as is some of the other accent pieces. The push button panel is easy to read and has a large knob for making manual time adjustments. The light inside is very bright. There is a rotating platter in the oven compartment that is not knocked off of its guide rollers very easy. The push button panel is a glossy black material that is easy to attract fingerprints. The preset times that are programmed in the microwave is the only part of the product that could be an issue. For example the popcorn button when used has burnt all of the different brands of microwave popcorn that we have tried. It is set about 30 seconds too long. There is no way to adjust the preset time that I can figure out. We set the time with the large knob manually and the popcorn comes out just fine. The preset times for the Auto Defrost are also a bit off. They are not long enough. We also have a Subzero freezer set at minus 20 degrees Fahrenheit so that may be too cold for the defrost presets. Overall the microwave is great except for the preset times that Ive mentioned. We use it daily and have done so for five years. It still looks excellent inside and out.

All I wanted to do was eat dinner with my husband and I wound up on the internet for an hour trying to figure out how to make our microwave work. There is some kind of thing that locks you out of using it. Very frustrating when you just want to eat dinner!! Nothing works and you have to google how do you unlock this piece of crap that you paid good money for and trusted the GE label. All we ever use is defrost food or time cook vegetables. If you want a complex computer, go for this thing. Otherwise, I suggest you go for a simpler microwave that you can depend on to work.

I purchased a full suite of GE Monogram Appliances about 5 years ago. All are fine except the microwave which was made in China. The back is rusting out, the inside is chipping at the door and moisture builds up in the door window. This progressive deterioration has taken place over the past 5 years. I paid $420 for the microwave plus $226 for the trim kit. Now, all GE wants to do is sell me a new unit and a new trim kit (will not fit old trim kit). I paid approximately $20,000 for the entire group. I bought GE because I trusted the name. Im stuck with GE if I want to match the remaining appliances. There are only two people living in this house so there is only minimal usage. To further complicate things, there is no serial number on the tag.

My GE microwave (Model: JVM1540SN1SS) that I bought new two years ago for $250.00 broke already. The table doesnt turn and nothing heats up even though the timer works. There are only two adults in the household using it, and we dont even use it very often. I find this pitiful service. My last microwave lasted about 15 years.

We bought a microwave oven (CVM1790SS2SS, ZA301193K) for our new house some 4.5 yers ago. The flimsy, but very shiny, metal cover on the door handle split and the resulting sharp, but hidden, edge cut my finger. We covered it up with scotch tape, and ordered a replacement for the handle. We paid GE $102 (other folk sell it for $76, as we later discovered). There were no useable installation instructions. Our extremely competent handyman could not figure out how to do it and called GE for help at 800 636-2005. He was rudely dismissed and was told to look for instructions on Youtube! He spent 2 hours to install the replacement part. The screws that came with it, were not quite right. Ill never buy another GE appliance in my life. The Item was ordered by Ellen ** (It was shipped on 1/17/2017).

So I was forewarned by my family of nightmare experiences they had with GE appliances over the course of the last 50 years of our family. I just bought a home with 2 GE dishwashers that are both under 5 years old, and both are malfunctioning terribly. The one has leaked from the bottom and created severe water damage, and the other will not drain. Just an affirmation of the bad experiences my family has had in the past. Cheaply made, and often the go to appliances installed in manufactured and new homes. Had a service technician come out after speaking with GE on the phone and they assured me it was cost free. After the technician came out and told me I was being billed $105 for the call, and it would cost an additional $255 to fix the washing machine. The tech was not very friendly or helpful, and his only concern was collecting the bill. Avoid these products!

We had to replace our dishwasher a few months ago and we got a GE Dishwasher and we could not be happier. This unit cleans so much better and seems to take a lot less time to do a full load. I would recommend GE to my family and friends.

Used the dishwasher for 1.5 years (it worked fine), but then the heated dry stopped working (only 1 year warranty). $500 for diagnosis and repair versus $700 for a new dishwasher. Guess I’ll be getting a different brand going forward.

I purchased a GE microwave about 5 yrs. ago. Got it on sales from Lowes. I love it. And it has been moved several times. And I have had no problems with it. It is easy to use and quite nice to look at. I would greatly recommend this product if youre looking to replace the one you have.

We sent the rebate form in, and they denied our claim. It was for a dishwasher that was recalled. We had to buy another one and only received $100 for the rebate after having to spend $500 on a dishwasher, but the rebate was denied! Unbelievable. We have written GE and the FTC with no response.

I was missing my wiring/ schematic diagram with my dishwasher and after spending hours on GE website to no avail I called the service center and was told they would send me an email that I would have to respond to and then they would email me a diagram in 8-10 business days. Email in 8-10 business days... WHAT!!!! I replaced the UI board after 2 1/2 years and the control board Fault code LED was blinking 7 times for a temperature sensor circuit has become inoperable. This is their fix; Disconnect the power at the circuit breaker for about 30 seconds and then reset the dishwasher. If the problem persists, contact service. No instructions on how to reset the dishwasher anywhere. American business at its best. Never GE again!

2 year old GE ADORA dishwasher - I am so disturbed tonight after seeing what happened to the protection rubber that is on the exterior of my dishwasher. I decided to buy a new dishwasher because the bottom tray would not stop when pulled out at the correct stopping point. Today I got my new dishwasher installed and when the installers pulled the old one out I was shocked to see that the protectant that I would assume was placed to protect my house was melted all over my wall behind the dishwasher. WOW. Talk about a MAJOR fire hazard. Thank God my house didnt catch on fire because of this faulty equipment. Check out my pictures and you will see the pile of protectant that was under, on my wall, and behind the dishwasher once it was pulled out. Sincerely concerned.

GE profile microwave TOUCH SCREEN pvm2070sm4ss - Almost new. Used properly. Touch screen failure. TOUCH SCREEN does not function properly making it almost impossible to use the microwave. This Common Problem should be a RECALL.........

Less than three years ago, I purchased a microwave oven wall unit to replace an existing unit. Due to the size of the built-in cabinet, I was limited in choices. The cost of the unit was $2400. A few months ago, the interior wall of the unit began rusting and the enamel is peeling. I contacted the customer service dept via e-mail on their site. I was asked to send pictures and then informed that I should stop using the unit immediately due to the danger of arcing. I was also told that because I did not purchase the extended warranty, the best that GE could offer me was a new unit for $800. I asked for names of warranty companies and was given one name and number but told there were others that also offered the same service. I called this company and they clearly told me that the peeling and chipping was a manufacturer’s defect and would not have been covered by an extended warranty had I purchased one from any company. Then I contacted the GE repair service center and spoke with them. The man who answered explained that this is a cosmetic problem and that there was no danger of the microwave arcing unless there was less food in the microwave than the size of the area that was chipping. I am very disappointed in the response of GE, the pressure placed on me to make a decision in 7 days or the offer would be withdrawn, and the fact that the service department and the consumer service (complaint) department gave me entirely different responses to the same information and problem. I will probably have my cabinet rebuilt to avoid having to replace this unit with another GE appliance. Who would pay $$1600 for the use of a microwave/oven unit for less than three years? Unfortunately, GE seems to be the only company that makes a unit that fits the existing cabinet in my kitchen. Disappointing to say the least.

Our over the range microwave oven is under warranty and broke twice. They refuse to replace it. It was fixed the first time but its broke again and the only service tech refuses to come to our home to service it anymore. Its been a nightmare and still not resolved. We will never purchase another GE Appliance ever again!

If you have a choice, run away from GE like the plague, because if you have to make a warranty claim, it may become a nightmare. I purchased a new home May of 2015, and my wife and I paid for the appliance upgrade to the GE Profile, which werent cheap. Less than 2 months I noticed that the microwave had a burn spot on the bottom of the door where it sits against the exterior of the microwave, the paint was burnt from the metal, and the rubber seal melted. I did not think too much of it because the microwave still worked and unless you opened it you did not see it, so it wasnt so much of an eye sore. Fast forward to January 2016, my wife informed me that the microwave stopped heating, and that she was going to put a ticket in to New Home Warranty, I informed her that we probably need to go to GE directly as I knew that is what they were going to say. So I called GE and put in a Service ticket. They informed me that it was going to be a little over a week before anyone would be available to come look at it, to which I was OK with. The repair guy finally came. I explained to him in detail what the issues were. He opened the microwave, closed it back, wrote some things on his computer, and told me that he ordered a part called the magnetron tube, which sounded like something from the transformers. He told me it would be a week before the part would be ordered, so I asked him if it wouldnt be easier for them to just replace the microwave. He told me that it is a warranty repair and they have to try and fix it first and if not, then they will. The evening before the repair guy was supposed to show up to change the door and the magnetron tube, I got a voicemail stating that the part will not be received until the evening of the repair, so they rescheduled me for 2 days later. GE just assumed that I would be available, because I probably sit at home all day waiting for service repairs. I called back the number to see what was going on. I was adamant that they replace the microwave, because by this time it was already 3 weeks without a microwave. And with small kids in the house it was very annoying to have to put a pot on the stove every time you needed to heat anything. After 45 minutes, I was still nowhere with them, so I ended up sticking with their new appointment window. I was leaving for work 2 days later when I noticed the repair guy at another home in the community. I thought to myself why couldnt he have done our repair the same day if he were already going to be in the neighborhood? About 45 minutes later my wife called me and told me that the repair guy showed up to repair the unit, that they were supposed to repair a day later, only to be told that the damage on the door was caused by arching, and that it will happen again so the microwave is non-repairable, so they will have to replace it. He told my wife that she will be receiving a call from the warehouse within 24 hours to schedule the replacement once the microwave is available, but she could call the warranty repair department to see if they could expedite it. After another 25 minutes on the phone going back and forth we were told that it will be about 7-10 business days before the microwave may be available. Now it is good to note that the warehouse where they stock the product is only 2 hours away from where I live. So by the count of it by the time we receive a new microwave, it would have been about 5 to 6 weeks from the initial call to get the issue taken care of.

GE profile microwave magnetron burned out after 2 years. Part is supposed to be under warranty, but repair is not. There are no service centers in my area. GE wont just send me the part, or let me send them my old part.

The key pad says it is shorted out and needs service. It turns on randomly. I unplug it and plug it back in and it will either say service needed, keypad shorted out’ or press clock .I dont use it much for microwave cooking. It came with the house we just bought and it only worked for 3 weeks before it started this mess. I could deal with it if it didnt beep all the time.

We recently purchased our second dishwasher in 16+ years (the other one (a Kenmore) is still running fabulously but staying with the sale of our former home - however I am tempted to swap it out with this new one from GE). This beautiful inside and out dishwasher has a couple main flaws that has me wanting my old dishwasher back. The buttons on the front are super sensitive, causing it to come on countless times a day as we get items out of cabinet above. This is not something we thought about. Our old one had the controls on the front but they were under plastic that you pushed... not actual buttons like this one.The second issue is minor. The rack on the bottom is set up very wide on one side and our dinner plates are smaller than some and they do not sit firmly in between the tines. The spacing is great for larger plates or serving items but not for medium size plates. We use a lot of bowls so the other side with closer together tines is always full. Like I said just a minor flaw. Lastly, the unit puts off a high-pitched sound during certain parts of the cycle. It is not really loud but it is bothersome if we are still in the kitchen when it is running.

We purchased the following from GE: GE Profile refrigerator, dishwasher, microwave, oven and cooktop in 2006 (six years ago). Last six weeks, the refrigerator, dishwasher and cooktop broke! We have insurance through Assurant on the products since it was recommended. We purchased the insurance for repairs and parts. Refrigerator - the motherboard (if you have other words for this) went out (4 weeks for a part). Now it is fixed. Dishwasher PDW8280NSS - This was the final answer from GE Consumer Affairs:I do apologize for this entire experience. I will be more than happy to contact you today between the time frame of 02:30-04:45 PM CST. Any additional questions you may have, you can contact me quickest by email. Again, I do apologize and I will contact you later today to discuss further options available to you. At this time, being the part is not available, the best option would be to offer a prorate on this dishwasher for you in order to have a functioning dishwasher in your home. I do appreciate your patience in handling this matter and will most certainly speak with you this afternoon. Thank you. Really, I have a case manager? The products must be really ** good if you need this as a department. Everyone should rethink buying GE products. Never again. I am campaigning against them! I cant get the part on a six-year-old high-end dishwasher. We live in the US, dont we? This should be a class action suit!

GE Profile microwave Model: PEB7226SF1SS came as part of the builder installation. In the first year had issues with the microwave not starting intermittently and had to call GE support who sent in a technician who had to work on the door alignment and the switch was the problem which said to have fixed. About 2.5 year from purchase the heating seemed to be irregular which we did not take much notice and then it stopped working completely. We called GE support and did get the usual routine of the product being out of warranty and have to pay for the technician. While scheduling they realized they did not have a their own service person in the vicinity and was advised to reach out to local service person.Local technician diagnosed that the magnetron has gone bad and advised most manufacturers have 10 years warranty on the magnetron as they are supposed to last for a long time and I should reach out to GE. Having reached out to GE support again to our surprise were advised that unlike most manufacturers this product did not have 10 year magnetron warranty. Customer service, part service and customer relations kept redirecting to each other. GE does not provide an option to sell the replacement magnetron to the customer and now want their authorized center to be engaged and paid again to have the part ordered and installed. Disappointed with GE product quality, their stand on warranty compared to their competition and their service which has given me run around and no solution. I have written to them asking for solution which they havent responded yet.

I recently purchased a GE Profile 1.9 microwave oven from Home Depot less than a year ago. Last week I went to remove something that I had cooked and went to close the door and it would not stay shut. I ended up getting some masking tape to try and tape it shut in order to keep the light from staying on and burning out until morning when I could get a better look at it, thinking that it had to be something small that could be taken care of without any problem. Hinge adjustment, something getting in the way that I couldnt see, etc, etc. Wrong! I have been over this door with a fine tooth comb and there is nothing that I can see that is preventing it from staying closed, not only that but according to everything that I have read, I am very lucky that I didnt get fried while trying to figure out if the latching mechanism was functioning correctly. I am not even going to go through the long drawn out process of dealing with GE over this due to the simple fact that I have been there done that with my dishwasher that showed up with the front panel dented a few years back from the factory and I ended up blaming the place that I had purchased it through instead of GE and have since found out by reading other complaints that this seems to be something that is not unusual when it comes to GE appliances. I spent over 1100.00 dollars on the dishwasher and they only replaced the panel instead of giving me a new one, and I have never been satisfied with the way that it operates, and it was a very long and drawn out process and I am just not willing to spend the time again on another one of their products. It is unfortunate that we have entered a time where customer satisfaction means nothing, and the days of caring about having repeat business from a satisfied customer are over. The prices continue to rise on the things that we have become to depend on and cant seem to live without, but the quality and workmanship have not only diminished but also present safety threats. I will never purchase another GE anything and I am looking forward to the day when we all have finally had enough of this and do something that makes these companies stand behind the products that they sell and quits ripping the consumer off. Its rampant across the board no matter what you buy, and there should be laws in place in order to keep it from happening. We have laws for everything else, why not have a couple that protect the consumer and their pocket books.

I wasted my whole day waiting for GE Technician to come. Nobody called me to let me know that they are not coming. I have to call them only for a Mr. ** to tell me that they had rescheduled the appointment for another one week without notifying me. Good job that GE APPLIANCES are doing. You remember the so called TOO BIG TO FAIL? It means, they can do whatever they want at whatever time or day they want. I dont have a vent in my house and that means I cant use the stove. Is this ridiculous or I am missing something here? Is it TOO BIG TO FAIL? Yes, I forgot that. I will be staying in a house with a new GE APPLIANCE that has not been working for the last one week and have to wait for another week. Mind you, this Appliance has been used only for barely a month. Is there anybody out there who is facing the same problem or its just me. If there is nobody going through the same experience, an excuse like there are no Technicians available to come to your place and do the job. If there is anybody out there who has trust in GE appliances like I did or even thinking of getting one. Be aware that you will be through what I am going through and there will be no technician available for another two weeks. Be ready to wait for they will reschedule your appointment without letting you know, why? Because theyre TOO BIG TO FAIL. What will you do? Wait until they decide to come, if theres a technician available. I just realized that GE means GO ELSEWHERE. Thanks GE for the good job.

Just two years old, the interior paint in my GE Microwave JES1072SHSS started to peel. I called customer service, then emailed, learned that the paint peeling posed no health problem, then, as a gesture of goodwill, given a $75 rebate. I foolishly bought yet the same microwave today (and will return it) as I read here on this site: not only is it unsafe to use a microwave with peeling paint, GE had a class action suit over this very issue and never took responsibility for the health risks to loyal consumers. So it gets returned this week. But PLEASE BEWARE. Gosh, I really bought the goodwill - hook, line and sinker! Then I read all the complaints here - about peeling paint.

The defect is in the Gas Control and Thermal Coupling, per my licensed plumber. GE tells me my water heater is still under warranty; therefore, I would like an authorization code to have it replaced by Home Depot where it was originally purchased. Home Depot tells me I need GE to give me the authorization code. BTW, your CS rep was very helpful. She is sending both items to me, but I prefer to have a replacement for the cost my plumber will charge to install parts in a questionable product. Thank you.

I bought this JVM1540SN1SS microwave just two years ago. From past five months, certain keys stopped working. Then today, it gives me error service may be required - keyboard shorted. Microwave is unusable at this point and out of warranty. But my previous microwaves worked for decade without any issues. This one broke in about 1.5 years. These microwaves are of bad quality. I think GE should recall these microwaves and get it fixed free of cost for consumers.

We purchased a GE Over-The-Range microwave, model LVM1750DM1BB in late 2008 and had nothing but problems with it, from paint peeling off on the inside to buttons which did not work, to burning smell, until it finally quit completely. Nothing worked, nada. This was not a cheap microwave and, added with installation expenses, was a major purchase. Even so, it would cost more to have it repaired than the original costs combined. This is criminal, a total rip-off!

I brought our brand new home just over 1 year and 8 months ago with all new GE appliances. One of the GE Smart Built-In Double Wall Ovens, the bottom one which we never use, but the inner glass shattered randomly, very dangerous and they want us to pay them $100 for the inspector visit and then more for the par and service $325 for the replacement, the GE is disagreeing they had a defect on installations. That is an experience that we never repurchase GE brands, my friend had the same issue. They replaced in their house this way without warranty, however they disagreeing our oven had the defect on installation, lesson learned, never never buy the GE again!

We bought 3 GE Profile appliances in 2005 when we renovated our kitchen. We have not had much problem with the gas oven/range/stove. We have, however, had nothing but problems with the microwave (which I submitted a separate review for) and the dishwasher. Recently, a friend made some suggestions regarding the dishwasher. I then went online and watched some tutorials on troubleshooting my dishwasher problems. I tried all the new suggestions and the dishwasher worked OK the one or two times after that and then back to all the old problems: 1. We have to scour every dish until its nearly clean before loading (even though the instructions specifically stated no pre-rinsing necessary). 2. I am not sure the soap cup opens. The soap is always left caked in the cup resulting in running the dishwasher twice. We have tried all kinds of various soaps and they all do the same thing. The eco-friendly soaps are the worst. We strive to be eco-friendly, but how can we be if we are using the harshest soaps possible AND running our dishwasher twice?! Not to mention the pre-rinse scour and running water until it is 120 degrees prior to running.3. The dishwasher also leaks and is very noisy.I have read some other reviews on this product and realize our dishes are not always dry at the end. This is a non-issue for me. I dont care so much if the dishes are dry. I do prefer for them to be clean. Dishes are a task I do not prefer to do. It would be nice to have a functioning helper. I am grateful the thing hasnt caught on fire. I saw that this dishwasher currently sells for $800-$1,500. I cannot believe it. I wouldnt spend $100 on this piece of junk.

I wish I had seen this site first. I purchased a dishwasher. It didnt even make it 6 months. Took a month to fix and then 3 months later broke right before Thanksgiving. It is now Friday before Christmas still not fixed. GE is closed. The repairman and GE both lie and said it would be fixed before Christmas. Do not purchase anything GE. They do not stand behind their products. The products are poorly made and dont last. Ive had several dishwashers over the years. This is the first GE and it will be the last. You will have to wait over an hour for on hold to reach anyone and even then they just dont care. Save your money. Buy a didnt brand.

Purchased new home and bought GE Monogram package. Within 6 months dishwasher started leaking bottom of door. After five repair service calls. (Thats 10 times waiting for service man or for parts to be stalled). The final repair killed the dishwasher dead and GE replaced it with a new Monogram dishwasher. I thought all was working fine but then this new dishwasher developed a leak underneath and the sensor shut it down completely. Service call made to GE and a GE service man came, only he couldnt get to the leak area because he couldnt pull the dishwasher out because the connecting water hose was being stretched so tight he said he couldnt disconnect it because he couldnt see behind the unit or the drawers to see where it was hung up. Plus he is not authorized to install or reinstall dishwashers. So I call GE repair and now have spoken to the most uncaring, dis concerned case manager handling my account. He tells me that this now a installation problem and that even though GE delivered the dishwasher and installed it that because these were outside venders they (GE) were not responsible for the installation and dont know if they used GE standards to install it. So because the GE service man couldnt move the dishwasher I now needed to get a plumber to disconnect the dishwasher, find out what the problem is with the installation, coordinate a service call date with GE service to then come out and put in the parts, then have a plumber back in to install the dishwasher again. GE will reimburse me up to $125 for the plumbers work and I have to submit the plumbers invoice. No guarantee that a leak will happen again, because the GE service man cant even run a test on the replacement parts because the dishwasher isnt hooked up to water and he cant do that because he isnt authorized by GE to install. Oh, the dishwashers warranty ended on 10/10/2015. My service call went in three days before it was to expire so service is covered for the leak (or so I have been told). But what will breakdown next with this appliance? I bought GEs top of the line package. I bought a MADE IN USA appliance and I can honestly say that this GE appliance turned out to be unreliable, unrepairable and their case managers uncaring. I will never ever, ever buy another GE appliance. I will never recommend any GE appliances to anyone ever. My KitchenAid lasted for 26 years without a service call. When I remodeled my kitchen I purchased a Bosch dishwasher. That pleasure was 13 years old when we sold our home. We have been in this new home for 1-1/2 years and now on my second dishwasher with a future of many service calls ahead and very bad taste for GE. If this leak problem is not fixed or another problem arises, I will yank this dishwasher out and buy another brand. A reliable one and definitely not a General Electric EVER! Since this GE Monogram package was purchased at P.C. Richards they will also be notified of my displeasure and I will continue my discourse of GE forever for their lack of product truthfulness and quality, plus consumer disregard.

About a year and a half ago, I bought a GE Profile dishwasher from a very reputable local dealer. Within 3 months, the digital control panel failed. Because it was still under warranty, the dealer replaced the panel. It failed again. This time they made other adjustments, it continued to fail. Finally GE suggested that the dealer replace the entire door panel, which they did. It took the repairman a couple of hours to do so. Still didnt work. Finally GE declared the machine non repairable and replaced it. Unfortunately the men who replaced the dishwasher didnt install quite correctly because it leaks. I keep a plastic container under the front left corner to collect the water every time the dishwasher runs.But the story doesnt end there. This machine and the first one both include a sensor that apparently check for objects that obstruct the spray arms. I dont know because theres nothing that tells me why the machine is beeping when I attempt to start it. I check the spray arms, move dishes, try to start it again and still get the beeper. I have done this over and over and over again and still it beeps. I have essentially emptied the dishwasher and it still beeps. When it does run, I have to use the boost temp. option and the longest cycle available to get dishes, and I mean dishes, even passably clean. Forget pots and pans, or casseroles. So, if you own a GE dishwasher, I hope that you have the old fashioned dishpan and dryer rack handy. Bottom line, it doesnt clean well, leaks, and beeps every single time I try to start it. Buy something else.

The microwave was purchased for above the stove. Its clean line and easy to use detail made it perfect for my little kitchen. Price was even better. Clearly, I would suggest checking value when shopping. Sometimes you pay more for another brand name and miss a real bargain.

Its a over the range model & came with a house purchase. It’s worked flawlessly for over 5 years now - even after being left with no air conditioning in FL for months on end. The only thing I could think to make it better is making it easier to choose longer length cook times. Button for half min & dial for all the rest can be irritating for your 16 min food.

Our GE Spacemaker XL microwave stopped working on 7/11/12. We purchased our house in January 2000 with the microwave included and have not had any problems with our microwave, until yesterday, when we woke up and tried to pop the kids breakfast in for a quick heat and it made a strange humming noise and you could smell plastic melting. All power was quickly turned off to the unit. Now to find a replacement for this built-in microwave is going to be a problem. The local technician stated the blower motor we need is no longer available. Thanks, GE, for at least 12 years of excellence. We are now looking for a similar replacement.

My dishwasher does an excellent job - its a bit slow, but it gets the job done reliably. It is probably slow only because its old and somewhat tired...It does a great job cleaning off remains on dishes, which is not always the case. It doesnt fail me.

A small black piece of plastic, which snapped into the back of the microwave handle has bent/shrunk, and popped off. My microwave is just a little over one year old. I called the GE 1-800 phone number for parts, and GE does not offer a replacement part for this, without buying a whole new replacement handle, which costs over $160.00.

Purchased the Maytag MDB7749SBM stainless steel dishwasher in December 2013. The dishwasher and install totaled $700, which for that price and with Maytags past reputation, I wrongly assumed that the dishwasher would last a long time. In May 2016, slightly over 2 years, the dishwasher started having issues with the control panel. The control lock would randomly activate. I would have to reset the circuit breaker daily, leaving it off for around 10 minutes. Even with trying to go through all the steps to resolve the issue, resetting it from the circuit breaker, sequence on the control panel, the dishwasher wouldnt work. I called Maytag and after 40 minutes on hold, they finally answered. They wanted $89 for a service call and for the $143 part, plus labor. Might as well just replace it with another brand like GE, or Samsung.

I purchased this dishwasher on April 2018 and from the beginning was not working well. I called a technician about 2 months ago, came with the computer and told me it is working fine, but my dishes are never well cleaned. Anyway on Nov 27, 2018 the water started coming out from my tiles and I didnt understand why? I kept drying and it kept dripping. I was so worried and called a handyman. He told me it is the dishwasher dripping water. All my cabinets, my tiles are wet inside. I have called and report it and today a technician was coming to repair it (which I will not accept.) I want a peace of mind. I need a new working dishwasher. Today, the technician was supposed to call me before arriving and I was 5 minutes away and left. Now, your customer service reps are telling me to wait till Tuesday. I am having guests and my house is a mess, I have the dishwasher in the middle of my kitchen, everything is stinking to humidity and all happens because of this BAD PRODUCT. I want this trash to be exchange as soon as possible.

RCA RMW953-White 0.9 cu. feet Microwave, 900-watts, 10-power levels, end cooking signal, glass turntable, 6-one-touch cooking menus, speed and weight defrost, cook by weight. Bubbles obscure text. I wanted a white microwave with a door handle, .9 and fairly powerful. I was glad to have found this microwave. But I dont know if the hole was there before, or my teenagers or I inadvertently put a small hole in the plastic covering over the control panel outside the microwave (NOT meant to be removed, I asked support) but now its become a larger hole as air got underneath. I cannot read the button text. I tried to cover it with scotch tape and thats not working.I searched and found out this is a common problem with GE microwaves. The buttons are very close to the bottom and therefore, countertop, so if you have a utensil or plate or something that sits near the microwave, it might nick the plastic coating. I called GE support (in India) and they said since its under warranty, I can return it. However Id have to pay shipping costs. Fortunately, I bought this at Wal-Mart (I hate to support this store but it was the only place I could find this style) and they have an excellent return policy and there is no charge for shipping. It was easy to call and request a shipping label within the generous warranty period. You might save yourself the trouble of a return or be very careful to not put a small hole in the plastic coating. Again, this is not protective coating for shipping, this is a permanent coating to protect the buttons.

We purchased several new GE appliances in August of 2016 as part of a kitchen renovation. We bought the GE Cafe series dishwasher CDT865SSJOSS. Within two weeks of use, the display stopped working. It took 3 weeks to get a technician out to fix display. Approximately 6 months later, we noticed the dishes were not as clean. Two months later the water stopped draining. Called a technician in, he diagnosed a broken pump. Parts would take 3 weeks and he would be out a week later. We are now over a month without a working dishwasher. He “fixes” the pump but says it isn’t draining great because your hose from your disposal is plugged (this hose drains to the same place as the dishwasher). Hire a guy to unplug the drain ($140). It isn’t plugged. The whole house is clear. Have to Shopvac out the stagnant water from the dishwasher that smells like a corpse. Call our plumber to check the lines ($500). He discovers that the technician pushed in the washer and busted a line. We now have water damage through our floor and into a bedroom below. He confirms that the plumbing is all clear and also finds that the technician never reattached the pan to the bottom so water was hitting the sensor and activating the shut off for a leak. Plumber fixes plumbing wrecked by technician, dries the sensor and attaches the pan. He advises that we run several cycles to flush out the stagnant water. If water still is not draining after several cycles, he advised that the new pump was faulty. Plumber leaves. We get 10 minutes into a cycle and the dishwasher stops for a leak again. I called GE hoping they would stand behind their product that we have now had for 2 years and have used less than a year. GE does not stand behind their products. The only thing they will do is send out a technician that you have to pay $100 for and they can’t guarantee that you won’t get the same technician who has come out 3 times and cost us more money due to his negligence. In May, we will be putting their terrible product out on our curb for city wide garbage collection. You no longer get what you pay for with GE. Do not buy their products!

I have a microwave that has a rack inside which gives you options other than using the rotating plate inside. Overall it works quite well. I did not purchase this microwave, it came with the apartment. Not sure if I would purchase this brand if I were to buy it for my own home.

I was sitting on my couch and I heard something running. I walked into the kitchen and saw my GE Profile microwave was running. At first I doubted myself and thought maybe I did something and then I cleared it out and went and sat back down. It did it again and again several more time. This is very scary. It was running like someone had set it and it was getting hot inside. Im not sure what else to do. The last time I had the same type of problem and just bought a replacement microwave and now this one is doing the same.

Beware of GEs scam! My new house came with a GE microwave oven model JVM1630. It no longer heats food so I called GE repair. Heres basically what they told me: It is likely the magnetron tube and it is still under warranty, so no charge to replace it but I would have to pay $99.95 for the repairman to come to my home to diagnose the problem. If I decided I didnt want to repair the microwave, I was offered a $100 coupon toward a new one but it had to be a GE and it had to be bought on their website only. If I decided to go ahead with the repairs, the $99.95 would be deducted from the bill and I would only have to pay for additional parts and labor. I repeatedly asked for a ball-park labor charge so I could make an informed decision as to whether it was cost effective to have the repairman come out or just get a brand new one elsewhere. The person on the repair line hung up on me! I called back and I was told the same thing; that no one could tell me what the labor cost estimate might be. I asked to talk to a supervisor and same story. I didnt schedule a repair because I was taking a long trip and wouldnt be using the microwave anyway. When I returned from my trip, I called GE repair and again they wouldnt give me a ball park figure. Frustrated, I decided to have the repairman just come out and repair the darn thing and an appointment was scheduled for the next Monday. I had to rearrange a Monday day trip to Wednesday and set the repair appointment. On Monday, it was starting to get late in the afternoon, so I called to find out if the guy was on his way. A recording said my call was noted and I would be receiving a follow-up call. About 10 minutes later, Kim in dispatch called to tell me she had to reschedule the repairman to Wednesday. I explained I already had an appointment on Wednesday. which was already changed because it conflicted with the repairman coming to my home. She told me the repairman couldnt come because his truck wasnt safe to drive so that whole day was shot. The appointment was rescheduled for Wednesday and I had to again reschedule my other trip. When the guy finally showed up on Wednesday, he told me to put a glass of water in the microwave and start it. Ten seconds later, he declared it to be the magnetron tube. He was at my house about 10 minutes, just long enough to take my $99.95 credit card payment and to give me an estimate of $246.90 to repair the microwave which included the free magnetron tube, a $20 part plus tax and labor. The estimate had instructions on how to get the $100 coupon if I decided to buy a new GE microwave, which he said is what most people do. He didnt seem like he came prepared to repair the microwave at all. I was so frustrated and already out the $99.95, so I told him to go ahead and repair it. He said I should call repair to schedule him to come back to repair it! I told him to just repair it now and he said he didnt think he had a magnetron tube in his truck. I asked him if he would go to the truck and check! He did, and nope, no tube and he left.I think this is a great scam GE and maybe others have going. Its entrapment. They get you to accept a repairman to come to your home and charge you nearly $100 for it, but give you a coupon for $100 for a new one but it has to be a GE and can only be bought from their website where they can go as high as $500 or $600. By the way, I got on the website to find a replacement. My model had been discontinued and the only one in my price range was also a discontinued model. They charge $75 to come out to install it and another $30 to take away your old one. I called local appliance stores to see if I could unload my old microwave for parts and they all said the same thing: stay away from GE products.

Have a GE over the range microwave oven, MODEL PVM1870DM3CC which started turning itself on for 6 minutes, repeatedly, WITHOUT being touched!

I purchased a Ge profile top of the line microwave installed over an electric oven. After 3 months the plastic handle came off and Ge replaced the entire door. This handle has now come off 3 times. The service tech said it has a plastic connector that weakens over a stove. It supposed to be mounted over a stove. This is just poor design and totally unacceptable for their top of the line microwave.

We purchased a GE JVM6175EFES microwave oven in 2014 and are now on our 4th unit. When cooking food, condensation forms and drips down the wall behind the microwave. GE replaced it with another, but it was a rebuilt unit which when operated caused sparks and smelled of something electronic burning inside. So another unit was ordered and delivered damaged. Now after a year, the 4th unit is once again causing condensation on the back wall. GE has no answer or explanation for this problem and really doesnt seem to care. This is just one of several problems weve had with GE appliances. We also had to go thru 3 refrigerators to get one that was not damaged from the factory. We will be trying to replace the microwave with a different model, but doubt if GE will work with us to get this resolved as their customer service has been no help at all. DO NOT BUY GE appliances.

Our General Electric Dishwasher does a very good job of cleaning and drying our dishes. It does these jobs very quickly and quietly. We have had it for about 5 years without any problems or repairs. I would recommend our dishwasher the General Electric Profile for home use. Several of our friends and neighbors recommended this dishwasher when we bought it.

Purchased an entire line of GE appliances for kitchen after having prior (still working) appliances for 13 years. Have had at least 5 services calls and countless emails and phone calls for non functioning Dishwasher. Here is response from GE Manager: I have reviewed the pictures and no I would re-wash those 4 dishes if they came out of my dishwasher prior to using them with my family. Dried on fruit, starches and dairy are tough for any dishwasher to take off as the sugars in them act like glue. Again for these types of foods we would highly recommend more pre-washing to make sure that they are not left on the dishes after the dishwashing cycle. CAUTION: DO NOT BUY.

I purchased a new Modular home. It came equipped with all GE appliances back in August of 2006. The dishwasher has recently been burning the basket prongs off, as apparently the coils are over heating! I had called GE about the danger of it being another recall. They informed me there would be an $89 service call. I dont have this kind of money; I am a senior citizen on Social Security. How can they charge me for a potential fire hazard?

I am now facing my 5th repair appt about my 2 year old microwave. I have spent nearly $300 on repairs to be told I can purchase a new one for 50% off. Well, $426 plus my $275 I have paid IS A NEW One! 20 hours of me having to be available for service. I did not know the life of this appliance was 2 years. GE complaint number **. This is an unacceptable resolution offered by GE!

Bought brand new GE Profile DW PDT845SSJSS as part of four appliance package to be installed as part of kitchen renovation. Bought in April 2018, renovation delayed until August 2018, install of appliances October 2018, installer by contractor plumber- excellent seasoned experienced installer. Never used DW until moving things into new kitchen. Washed dishes off in DW before placing in cabinets. After 3rd cycle- DW stopped working stating leak detected - contact GE. Are you kidding me? Brand new appliance! We had original installer come out- no leak- no visible water- we went to placed we purchased DW from - local place - Ray’s Appliances- asked for replacement DW. Was told we would have to pay for installation of 2nd DW at 225 charge. Are you kidding me? GE guy came out and did something to DW to fix it but said problem could return... Serious??? Well -DW worked for a few cycles- now displays leak detected again! Called GE and coming out 12/2. Ridiculous- I want a NEW DW with free installation! I’m paying @971 bucks for something that didn’t work from the outset!!!

Slow leak that caused E4 code to beep incessantly! Had a warranty repair person look at it... Turns out the new dishwasher has a faulty seam that in fact leaks! This is all fine until... one has to make numerous calls to the GE warranty line, which should be called a WARNING Line. The customer service rep was very rude and reprimanded us for not noticing the leak sooner, he seemed to not believe we had any issue... All because they could not find the service repair # that was submitted.Anyway, two weeks later we still wash our dishes and NO one has called us back from GE with any answers... SO FRUSTRATING! DO NOT BUY A GE PRODUCT whatever you do... This company has the worst customer service and warranty program. We make our daily call in hopes of being looked after one day... They keep telling us that a manager has to approve the replacement of this POC unit we spent $917 on!!! My business partner is about to purchase 20 GE dishwashers for his apartment block... I guarantee that his order will change after we chat this weekend! Thoroughly done with ALL GE products after this nightmare!

I bought the microwave in 2005. It is an above the stove type microwave, black color. It has been a great microwave for all of these years and still keeps going. I would buy a GE again. It has been a solid microwave and all parts but the turntable are still functioning after all of these years.

I bought this Microwave JVM3160 on December 2016, after six month the handle door broke but it was replaced as part of the warranty. By January 2018 (no more Warranty) it began tripping the circuit breaker. I change the power source for a dedicate circuit only for the microwave 20 AMP. The microwave blew its own fuse. I replaced its fuse. Then it blew the 20 AMP circuit breaker. That was enough. This microwave went to the garbage after 1 year and 2 month of use.

I have a GE dishwasher that shut itself off after three uses. It was rebooted by a repairman, and worked once. GE repairman called to let me know and I was originally scheduled for today but have been canceled. I’m taking the day off but for nothing. There’s no number to call. There’s no one to complain to. JCPenney is not standing by their merchandise because I did not buy an extended warranty. Originally purchased in November 2017. The machine was replaced by GE in December 2017. I have a dishwasher that I paid over $500 for and I’ve used it four times.

Have to rinse dishes clean before I put them in. Otherwise they will not get clean. Does as well as most other dishwashers- until you get into the very upper end ones. The racks are good size. The outside is nice looking.

No issues yet. But only had for 6 months so time will tell. Read a lot of negative reviews but none here. Bought in Nov ‘18 from Home Depot. Delivered and installed on time. Replaced 13 yr old GE appliances that were still working.

I love the way the dishwasher is so quiet and cleans the dishes well. However, they are ALWAYS WET. A repairman came and told me that I could not expect the dishes to be dry on the light cycle with the POWER DRY. He told me I have to wash on the normal cycle. I did that and they are still wet. He came back out again and basically had no viable explanation. I have to have a dish towel in hand to dry the dishes as they come out of the dishwasher. I paid a lot of money for what I consider the piece of junk that is sitting in my kitchen. I will never again buy a GE PRODUCT.

GE Triton XL dishwasher overheated for no reason and melted the inside components to the point they are scorched black. This dishwasher is worthless. There would have been a possible home fire if we were not at home at the time of incident.

I have had my fridge since 1984. It runs great and I have not had any problems with it. The freezer is on top and it keeps the food well frozen. I think the key to keeping food properly chilled and frozen is setting the temperature controls properly.

We purchased a complete kitchen of Profile appliances. Everything is fine except dishwasher! The first one didnt clean food and left scum on everything... The company sent service several times replacing many parts.... finally gave us a new one... It still doesnt clean. It will not remove peanut butter, avocado, and my teacups are perpetually stained dark brown. My old dishwasher, Kenmore, left my dishes sparkling... no matter what was on them, plus I didnt have to run my kitchen sink to get hot water first! I will not use GE in my next house which will be built in about 3-4 years.

Periodically my GE Profile Dishwasher will not clean well. On every occasion it is due to clogging of spray ports on the upper and/or lower spray arms. Removing the blockages is nigh-on impossible as it is often not possible to extract the blockage from the outside and its not at all possible to flush the blockage back down the arm to extract it at the centre. All that is required is a bit of forethought and the creation of some access to the arm. I was frankly surprised to not be able to find a replacement arm as the suggested solution to this problem, the additional part revenue being part of GEs the business model. There are a number of other design issues with the assembly at the bottom that make me think it was done by an intern and nobody checked her work at the end of summer break before it went into production.

I purchased a GE dishwasher model no. GLD6700N00CC, serial no. ** about 4 years ago. It just finished the wash, rinse and drying cycle when without warning, the front panel on the dishwasher started smoking and spewing fumes in my kitchen. The front door of the dishwasher and top of my counter were extremely hot. Luckily, I was home when it happened. Otherwise, I might have come home to a fire.