The protective lining inside the microwave is coming off in a number of areas and the metal is visible and rusted. Is it hazardous to use the oven which is otherwise working? I contacted the Consumer relations department of GE and was told that its not repairable and offered only $25 as rebate to buy another one from them or any other retail store. I visited a couple of merchants, online and in their store, shopping for a similar product and got a price range between $250-450 plus $110 installation fee for a similar OTC microwave oven. We have all other appliances at home from GE and this does not give a good confidence about the products from GE.

Have had dishwasher for 3 years and it quit working. Had appliance repair people out 3 times and they replaced every circuit board and harness in dishwasher as per GE and still doesnt work. GE own techncians dont even know how to fix it. So I am replacing it! No more GE appliances for me!

We bought the GE dishwasher from Lowes 3 years ago and have had it serviced 3 times! The water pump went the first year and now the drain pump! Love the coloring Slate but very poor quality. Will not purchase GE products again.

Even though the dishwasher was bought 15 months ago, it was only used for the last past 5 months. There is no water fill up the washer. When I call GE for the service, the operator keeps saying that it is out of one-year warranty and I have to pay everything to fix it; I have proof that the product was in use under 5 months. The product clearly has a problem. I am not happy with their services and with the product.

Our GE Microwave Oven/Convection Oven Combo (Model: PT970SRSS) is a little over 2 years old. The interior paint on the ceiling of the microwave oven is chipping and bare metal is exposed. In addition, the microwaves glass turntable frequently slips off its plastic tripod base. Circular scratch marks, which also expose the underlying metal are evident in the area which is located directly below the glass turntable. The circular scratches are a direct result of the glass turntable scraping against the paint. The GE repairman said chipped paint is not repairable and that paint should not ever chip in a microwave, let alone a relatively new microwave. After many calls back and forth to the GE Consumer Relations person, we were offered a new combo at a discounted rate of approximately $1,000. (We paid around $2,000 originally.) Im not satisfied with this offer. I strongly feel that consumers should NOT have to pay to replace a defective item. GE needs to pull these defective and dangerous products off the market! Take a lesson from GM!!!

Similar to another comment, we bought the entire suite. Dishwasher cycle screen gone after five uses. Oven temp needs adjusting. For the quality we were sold, this is extremely disappointing. Bought extended warranty, thank God, so will see if it was worth it.

GE Profile Microwave JVM1850DMCC - For the third time in 5.5 years, Ive experienced a magnetron failure in a GE Profile Microwave. The first failure was fixed under warranty. The second was so bad, the microwave had to be replaced, but it was no longer under warranty. I should have heeded the warning and gone to another brand, but on 12/31/10, I paid over $500 to replace the microwave with a new GE Profile to match the existing appliances. Apparently this was a big mistake as the magnetron has failed yet again. The microwave is on its own separate 20A circuit, so that shouldnt be an issue. It would seem, however, based on the number of complaints I see on this site, there is something inherently wrong with the manufacture of these microwaves, or more specifically the magnetrons. Im extremely disgusted at this point.

I own a GE counter-top sensor microwave oven model #JES1451, which was only 2 years old. At 3:00AM, I woke to a room full of smoke and a burning plastic smell. I immediately rushed to the source which was my microwave oven. It was going by itself and the panel read sensor error with smoke billowing out of it and flames erupting. Luckily, I had a fire extinguisher handy. I had never had any problems with this microwave prior to this experience. I cringe at the thought of what could have happened to my home and my family sleeping upstairs if I hadnt been nearby.

Our GE Dishwasher is about 22 months old and is now not starting. GEs customer care is a joke. All they want to do is send a repair person with a $110 fee just to come and the person making the appointment refused to tell what the labor rate would apply once they got there. They offered zero help as far as troubleshooting. I called a local repairman and was told he has had many similar issues with newer GE Dishwashers. We are throwing parts at the problem now trying to get it running. He also said repair assistance or troubleshooting from GE is very poor. Really not pleased having a less than 2 yr old major appliance not working. GE means JUNK to me.

We purchased a GE Profile dishwasher, model PDW9880J00ss, in July 2005, along with GE range, refrigerator and microwave oven. We have had nothing but trouble with them. Most currently, the power board did not shut off at the end of the cycle, overheated and melted the harness also. We were alerted when the odor of burnt plastic filled our home. It was fortunate that we were home and in the next room, or our house could have burned down.The dishwasher cannot be repaired. I will contact GE to see what, if anything they will do to compensate me, but I am not optimistic. I will never buy GL products again. I thought by buying top of the line products from a well-known manufacturer, I would have a quality product. I was totally wrong. Sometimes, you dont get what you pay for.

GE Microwave Model WES1450DN1BB 1.4 Cubic Ft 1100 Watt - This product is absolute garbage! This product was manufactured in June 2010 and I purchased it in approximately in May of 2011. So after 13 months of moderate use, the unit no longer functions properly. Needless to say, the product is out of warranty by about a month, so I pretty much now have nothing more than an overweight paperweight.I wont bore you with all the details, but for the most part, the touch pad stopped working and if left plugged in, the microwave will start on its own and run for up to a minute before beeping incessantly. If I unplug the unit and plug it back in, Ill receive a different error message, and so on. I wont waste my time contacting GE, because from what I hear, they really dont give a damn!When I was young, you could by an American-made product and expect it to last for many years. However, ever since greedy corporate America decided to ship all our jobs overseas in the name of profits, I have yet to find any imported products that are worth a damn. Instead of one good American product that would last a lifetime, I now have to purchase the same imported piece of ** many times over to get the same longevity. Maybe this is what GE wants?Needless to say, GE has now been placed on my Do Not Buy list. I guess I will now buy from another major manufacturer to see if their foreign-made garbage is any better!

First Profile microwave/oven caught on fire. Was replaced. Front panel on Profile refrigerator not reacting to touch. Repairman said that this model had problems. Fixed it - cost over $100.00. Dishwasher (Profile series) not worth the cost of heating the water to run it. Cleaned dishes by hand. Stove top died - not reacting to touch. $90.00 for repairman to visit us, and another $60.00 to tell us what was wrong. A lot of money for inferior products.

Paint is peeling on the top part of the oven. It could fall into food. This seems to be a common problem. Called GE. They said it could not be repaired and to stop using it. Buy a new one. What kind of product do they put out that cannot be repaired? Not very good in my estimation. Customer Service did not offer much assistance to replace it. Be warned. Don’t buy GE products.

I bought a GE dishwasher that has a plastic tub. The tub smells. I asked GE to replace it, they wont because they say it operates correctly. I cannot imagine why any manufacturer would use a product in a dishwasher that STINKS. The plastic even has a warning for California consumers, that its a cancer-causing substance. Im glad I dont live in California, so it will never cause cancer here....

Does not hold as many dishes, pots and pan as my previous dishwasher. In the bottom rack I cannot place plates and bowls side by side. Rack is too small and the gray interior is too dark. And the top rack does not hold the glasses in place, already had one break.

Needing some type of warning to indicate a clog or break down. Cycle: Pots & pans; heavy wash; normal wash; light wash; hot start; high temp. wash; heated dry; energy saver; cycle on: plate warmer; start delay (hrs) off, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1; Hot start plate; Pots & pans start; heavy/normal; high wash; heated dry off-rinse only. The color fits my kitchen arrangement. Needs to have a better warranty coverage. Needs a longer warranty on the basic coverage. Do away with extended coverage. Offer all parts and full labor for a longer time.

We moved into our home just over a year ago. We replaced all of the kitchen appliances; refrigerator, stove, microwave, and dishwasher with GE slate gray appliances. This was in November, 2014. On New Years eve (2016), the dishwasher flooded the kitchen. I removed the kick panel and saw water pouring from the pump. After the holiday, we finally got in touch with the appliance repair shop who handles GE warranty work in our area.They contacted GE on our behalf to see if GE would stand behind a product that was just over 1 month out of warranty. Bear in mind, this wasnt something simple like an indicator light burning out, this failure was catastrophic. GE basically told them (and us) to pound sand. We are a 2 person family. The dishwasher was used maybe twice a week during the year weve owned it. Amazing quality! Now Im looking forward to watching the rest of this stuff fall apart. It looks like the life span of the product and the warranty period are the same. How handy for GE. They must not have to depend on repeat business or take these negative reviews seriously.

My Profile dishwasher is not on the recall list, yet the heater element malfunctioned and did damage the entire inside racks and spin bar along with contents. GE told us to have their recommended repairman provide estimate. Repair guy estimated over $600 to fix. The unit was smoking hot which caused bubbling on the exterior and the dishes to show signs of burning. Well with estimate, GE is offering a discounted top of the line dishwasher for over $600. Pretty sure, I do not want another GE. Also, when I told the agent that I was afraid that if I had not been home, it may have initiated a fire, she said it would not have happened. Really?

Our microwave, model number JVM1750DP1BB, was manufactured May 2011. On Monday, Dec. 30, I was heating a bagel when the small plastic hook holding the rack caught fire. The interior of the microwave burned, but I was able to put it out before it spread too far. I shudder to think what might have happened it I had been in another room. Im irritated because I keep reading that this is a common problem. Im irritated because MY HOUSE COULD HAVE BURNED DOWN. Im irritated because it seems like GE isnt doing a great job at making it right. Ive attached a photo below, showing where the plastic pin burned. I can say that Im shopping for a new over-the-range micro, and it wont come from GE.

The microwave is large enough for a whole chicken and operates at both a high speed and good efficiency. Most items can be timed within minutes of properly prepared meals.

My husband and I enjoyed our 1980s White GE Microwave and Stove/oven. But, after 15-20 years with the same appliances, we finally saved up for upgrades and purchased a new Stainless Steel (mid-range priced) GE Microwave and stove/Oven. I cannot begin to describe our disappointment. The Microwave is above our Stove/oven. Our old microwave had two powerful lights underneath it - one on each side. This microwave provides one small, weak light that does no good any time of day. Why would GE go from two great lights to one middle useless one? Also, the faint white numbers on the front keypad of the microwave are barely visible during the day - forget about seeing this when the light is not perfect. I foolishly assumed these numbers would be backlit on a black background. Onto the Stove/oven. The temperature is not accurate but that is something we can deal with. After the oven is pre-heated, the assigned temperature stays on the display pad - NOT the actual time. Who cares about the temperature you set the oven to - dont we all need to know when to check or take out our food? Our last oven always showed the time. We did not join the Stainless Steel bandwagon 10-15 years ago when others did - which we thought would be good for GE to get some kinks out. I Guess we should have waited 10 more. Proper lighting on your Microwave and The time on your stove/oven while cooking are not too much to ask for when we just dropped at least 2-thousand dollars!!!!!

Have used GE dishwashers before - were good. However GE no longer makes them, its just a name - now made by MABE (part of HAIER), Mexican with Chinese ownership, and this new one arrived with a factory fault - cracked tub which leaked immediately. Cracked tub seam and leak found immediately by service tech GEs site referred. Good news is the leak detector worked! Bad news - is we didnt install it right away (old one still worked and pandemic...) so it was a year before we got to it (was partly a gift). So - now MFR Mabe is giving us the run around and so far not doing anything about the faulty dishwasher they mfd and shipped through Home Depot. Dont be fooled as we were - GE is not actually GE anymore and the mfr HAIER/MABE are doing nothing to correct a factory mfg fault.

So I was forewarned by my family of nightmare experiences they had with GE appliances over the course of the last 50 years of our family. I just bought a home with 2 GE dishwashers that are both under 5 years old, and both are malfunctioning terribly. The one has leaked from the bottom and created severe water damage, and the other will not drain. Just an affirmation of the bad experiences my family has had in the past. Cheaply made, and often the go to appliances installed in manufactured and new homes. Had a service technician come out after speaking with GE on the phone and they assured me it was cost free. After the technician came out and told me I was being billed $105 for the call, and it would cost an additional $255 to fix the washing machine. The tech was not very friendly or helpful, and his only concern was collecting the bill. Avoid these products!

I had nothing but problems since day 1. The dishwasher has never cleaned dishes properly. We have to pre-scrub. The soap dispenser does not operate properly. The keypad stopped working after only 2 years.

I purchased a microwave in Oct 2010. It went blank and nothing works. I checked to see if its receiving power. The power is okay. I purchased the microwave, fridge and stove at the same time. I always had confidence in GE products. Microwave should have lasted longer than less than 2 years. I didnt purchase extended warranty because of GEs reputation. Very dissatisfied customer.

I spoke to someone in the customer relations department after contacting GE cares. Our GE refrigerator purchased 16 months ago had malfunctioned. Within minutes of explaining the problem GE located my file in their system. They immediately extended the manufacturer warranty as a courtesy. I didn’t have an extended warranty but GE arranged to have the service technician come to my house to repair, what he discovered was a broken fan, in less than 24 hours at no cost. While the likelihood of a fairly new appliance needing repair is rare, the service technician did explain that repairs needed with GE appliances does keep him very busy. I am thankful for their CARE and saving my Thanksgiving turkey!

I give it stars for value because an extra step is needed to set cooking time. Most microwaves do not require pressing a cook time key before selecting # of seconds. Other than that, microwave is first-rate and very dependable. We use it several times a day for 1.5 years now with no problems.

First off: GE doesnt make some parts for this model anymore. The unit is large compared to many others; the upper tray provides adjustable height; one of the set of spikes in the upper tray rusted out because of inadequate plastic coating, and no replacement was available from GE; the control panel on the top edge of the door failed within warranty period and was replaced free; the holes in the rotating arms that spew water upwards onto the dishes must be cleaned with tweezers to remove bits of paper from labels. Those are all the negatives. The positives are that it is very quiet; a cycle takes about an hour; it cleans dishes well so long as they are not hidden from the water jets; pre-rinsing can help but is not necessary. I would buy it again.

Microwave counter top - On Oct. 15, 2010, I purchased JES1460 DNWW at Pacific Sales San Jose. Since then, two service calls on this microwave which replaced one that did not work. New sensor on service call 10-10-11. Today is 3-6-12, strong electrical smell practically knocks you out. I unplugged the unit. We always purchase GE appliances. No more, very poor quality. We are upset.

I have a built in model that is now 9 yrs old and still operates as well as the day I bought it! I will definitely buy GE again. I have family members that have owned 2-3 microwaves to my one, that screams quality.

4th service call for a piece of ** over the range microwave that keeps breaking. The service is a joke too. The sent some moron to come take a look at the microwave after I placed this latest service call. He came and without diagnosing, he ordered a few parts and scheduled a follow-up for today. He called this morning to reconfirm the appointment (which was already confirmed 2 times previously and this reconfirmation has never taken place previously) and I missed his call. When I called him back short whIle later, his voicemail directed me to call the 800 #. After a 35 min hold with them, they said since I didnt pick up the phone in the morning, the appointment was canceled. What???? It states nowhere that theyll call you to reconfirm an ALREADY SCHEDULED AND CONFIRMED appointment and that if you miss the call, they cancel the appointment. Next service call is a week from now, which makes it 3 weeks without a microwave. I hope they rot in hell.

I bought a microwave unit (HVM1540DP1BB) in August 2011. The warranty expired in 2012. But just a little over 1 and 1/2 months after the expiration, the unit would not power at all. The display did finally come on after a day with plug disconnected showing **, but if finally came to life. No more than a week later, the same thing happened. This time the unit does not come back to life, no reset. I had replaced in 2011 the original unit that the home builder had put in. That unit last eight years. GE makes terrible microwaves and I will not replace it this time with a GE.

The interior paint on the microwave is peeling causing there to be sparks in the interior of the microwave. The microwave interior paint is defective and should not have peeled. The microwave interior has metal showing which causes sparks.

My experience with GE over range microwave oven as follows/ Unit Mod.JVM3160DF3WWW. Ser.#GH260692A, this unit was purchased April 2017, February 2019, unit began to disconnect itself during normal use. This was done by way of throwing 15 amp breaker. No satisfaction from GE, NO extended warranty purchased, guilty as charged, contacted elect. tech. No idea of problem, #2 elect. problem in door sensors of which there are numerous, notice black residue on duel latch on door caused by door latch device rubbing on unit latch receiver cost to discover which sensor cause and replace one or all 250.00.We have been limping along for two months with frequent trips to basement resetting breaker (which we had replaced) next move, purchase NEW MICROWAVE. Let me be very direct if we wanted JUNK we would buy Asian made, THAT being said, there will be NO...General Electric products in this house. This is our second GE product BUST, 100.00 advertised by manufacturer. Never delivered! But hey we are just small time consumers. What might else we expect.

My less than a year old GE microwave stopped working last week. My AT&T phone service died so I had to make repair arrangements online. Guy was here this morning. My microwave’s main board is fried. It does not conform to Repair Guy’s published schematics. Repair Tech could not upload new data to it. Repair guy did order three new parts including a main board. GE told Repair Guy that mainboard delivery ETA UNKNOWN. After three hours here repair tech left and told me to call GE customer care. Believe it or not, two hours on telephone with GE. First you need to talk to a customer service rep that cannot help you. They then determine you need a Customer Advocate. Then they need to input data on your file for the Customer Advocate.Then they need to transfer you to that department. Then you have to get a case number assigned. Then you give someone all the serial numbers and model numbers again. Then the Customer Advocate (CA) takes the call. The CA does not speak English as you and I speak English. After the CA puts me on hold to verify the purchase, then the appointment, then the tech and then the order they actually speak to me. In my case, the mainboard part is not available on CA’s computer. The CA has to electronically contact the parts department to find out if the part is in this universe. If the part can be delivered to my Repair Guy in Jackson, GA within 14 BUSINESS days from the date of the inquiry I have to take the part and wait for repair.In the event the part cannot be delivered in 14 days CA will start a process to get me a new microwave. The parts department has up to 48 hours to respond to the CA. When asked what happens if no response occurs in 48 hours, I was told, That never happens. It is the Christmas Holiday and I anticipated guests. My husband is disabled and his meals are pre-made frozen so I will have to decompose them and heat them on the cooktop. GE could care less about those issues. So after waiting five days for repair I have no working microwave. Someone told me not to replace my GE with a GE, but I did not listen. It is December, holidays, no microwave is an aggravation that I thought paying for a GE product would alleviate. So, on January 2nd I might get an answer. Part possible or new appliance COULD be ordered and delivered by someone sometime.

I bough a GE microwave oven, model JVM1740SM1SS, less than 2 years ago. The keypad says that it is shorted out and needs service. It turns on randomly. I unplugged it and plugged it back in, and it will either say, service needed, keypad shorted out or press clock.GE has so many complaints about there microwaves, some that are very serious. They still claim that there are no problems with them. They have to know there are problems, but do not want to issue a recall and take a financial lose. Its only a matter of time, before something so serious happens that it will be a bigger financial lose than a recall.

I bought GE Profile appliances 5 years ago. The dishwasher motor needs a new one. It cost me $300.00 to fix and I ended up buying a new dishwasher, of course, no more GE. Six months ago, my GE profile fridge is not making ice. It cost me $300.00 to fix. Now, the freezer is not working right. I was told another $300+ to fix. I went out and bought a new fridge. Back to basic, Kenmore brand. GE profile is not inexpensive and only last 5 years, starting to break down. Please stay away from this company.

My microwave (model#JES1139BL03 and serial#901897B) is peeling around rolling fixture that holds glass tray. I wipe it with hot water and it continues to peel off. Its almost all gone. Ive only had it two (2) years. This cant be normal. Anyone else have this happen?

Have a GE dishwasher put into operation June 2016 (new home). In Oct 2016 we noticed a leak and a serviceman came out and identified a loose soap dispenser - tightened it. Next time we used it, leaked as before. Same serviceman came again, this time replaced both the main seal & spinning water distribution wand assembly. Again, the unit leaked and on Dec 14th same serviceman replaced the soap dispenser. Before he got too far down the road, we called as the unit again leaked. He blamed it on excessive soap suds - which he removed manually. Following his departure, we again experienced a leak. Same serviceman returned on Dec 15th. After review, he advised us the DW would be replaced and we should get a call within 48 hrs to arrange. On Dec 17th (still no followup from GE) the DW leaked again - we video this time. On Dec 19th called customer relations and after much discussion it was apparent GE has NO CLUE what the heck they are doing. ONE MORE repair trip was scheduled - this time they would replace the inside and outside panel! We are fortunate to be retired otherwise this repair process would have cost us about $2000 so far! How idiotic is GE?? How much have they spent to avoid replacing this unit? Believe me this is the LAST GE appliance we buy from them. Dont know how they stay in business. We are awaiting the panel repair guy as of this writing. Will update once this service has been completed.

Dishes on top shelf do not get clean, and Power Dry does not dry dishes. Technicians say nothing is wrong with the unit and customer service was a nightmare.

I purchased a this GE Model CDT845P2NS1 on Oct 2, 2019 and the unit was received Oct 23, 2019. I installed the unit approx. 4 days after receipt and dishwasher functioned well until November 10th, 2020 when the unit failed to pump out the water. I contacted GE Service (MabeService) and was advised that the unit was not under warranty and as such I should contact a GE Canada authorized service centre.After several attempts to get someone to come to our location at Sharbot Lake we got hold of Capital Appliance Repair in Ottawa. They were not able to send a technician until November 18th. After diagnosing the problem the technician advised we needed a main control board and would have to order one and then come back to do the install of the control board. It is now February 21st 3 months after the visit and I’m being told that the part is backordered and they have no idea when it will become available. I’m extremely unhappy when you spend over $7,000.00 for a GE CAFÉ gas stove, Microwave, Refrigerator and dishwasher to find out you cannot get parts in a timely manner. As a customer of GE Canada I have had no help is solving my problem. It is not acceptable to have a 1 year old dishwasher that has failed, much less waiting for repair that has taken over 90 days to get repaired. DO NOT BUY!

I purchased a full suite of GE Monogram Appliances about 5 years ago. All are fine except the microwave which was made in China. The back is rusting out, the inside is chipping at the door and moisture builds up in the door window. This progressive deterioration has taken place over the past 5 years. I paid $420 for the microwave plus $226 for the trim kit. Now, all GE wants to do is sell me a new unit and a new trim kit (will not fit old trim kit). I paid approximately $20,000 for the entire group. I bought GE because I trusted the name. Im stuck with GE if I want to match the remaining appliances. There are only two people living in this house so there is only minimal usage. To further complicate things, there is no serial number on the tag.

I have had 2 of GE microwaves, above the range models. Both the same model, but different years. One stainless finish and one almond. They are almost exactly the same. They are efficient, and I like the carousel for even cooking. But I would like it if the light bulbs under unit were easier to replace.

We just purchased a new home and moved in about a month ago. The builder would only put in GE appliances despite our protests. We had purchased another new home 2 years before with a new GE water softener and GE reverse osmosis system. In the 2 years we were there, we had service people over on multiple occasions because they never worked correctly. The common message from all the service people was that GE makes junk. Corporate designed garbage designed to last only as long as the warranty. Dealing with GE was always a nightmare with long waits and customer service that worked banker’s hours. In other words, GE does not stand behind its garbage.In any case, we just bought another new house and the signature series microwave (billed as the best they make) would start to run spontaneously and beep when nobody was near it. We had to shut off the power to it just to make sure our house did not burn down. We researched it on the web and determined the keypad was bad. We told them this when we called in the warranty. They took a week to send a technician who would only work banker’s hours and forced me to take a day off work. He gets here and tells me that he had just tested the microwave and learned the keypad was bad! Duh! He then proceeds to tell us that he did not bring a keypad and that he would have to order one that would be mailed to our house. We live on a new street which address is not recognized by FedEx so we told him he needed sent to himself. He refused. He assured us that we would get it. So, Friday 3:00 pm rolls around and no part shows up so we call to find out what is going on. Mind you, I have already scheduled Monday off work at this point. They tell me that the part is back ordered and that they have no idea when they can ship it. Additionally, they have a wrong address for our house. We tell them the correct one and they tell us their computer does not recognize it. She cannot tell us when the part will be available. We tell her that this is unacceptable and that if they cannot replace the part, they need to replace the microwave. She says that is not her department and we have to call their customer department on Monday which is open from 8 to 5 pm Eastern time! We live on the West coast!!! That means they are only open until 2:00 my time and I have a job where I cannot make calls during the day. I can’t do it at lunch because the hold times are over an hour!!! I guess I have to get up at 5 or take the day off.When I tell people in the know about this, they just laugh and say, “whaddya expect!?!, its a GE!”. We have been about a month with a brand-new microwave that has never worked and GE is impossible to reach and has not even ordered the part!!! We are toying with the idea of just replacing the piece of junk with a product manufactured by a reputable company like Samsung or LG from a box store who will honor returns and take the home builder to small claims court. In any case DO NOT BUY GE PRODUCTS!!! You have been warned. They make cheap junk that never works right and play games so they dont have to honor their warranties. This is a New York Corporation run by people who do not care about customers, honor, or integrity. They make backdoor deals with shady homebuilders to peddle their junk exclusively and you will have to replace it in two years. Learn from our mistake in buying GE. They bring junky crap to life. Garbage Electric is what they should go by.

We purchased the suite of Cafe appliances. After one year of service, out of warranty of course, the touch pad on the microwave quite working. The touch pad on the dishwasher has several lights that do not work. These products are insanely inferior. If you are considering purchasing, I would buy anything but GE.

SOLVED: PDW9980L00SS GE Profile Dishwasher not cleaning dishes. The rubberized sump of this dishwasher suffers from chemical deterioration. In our case the deterioration allowed waste water to bypass a check valve and return into the wash water. Dishes dont come out clean and the spray wands get plugged up with bits of waste. The solution is to replace the sump. If youre handy with tools its an easy DIY job which requires pulling out the dishwasher and turning it on its side for access to the sump. Lots of videos online re the process and for safety start by shutting off the circuit breaker for the dishwasher power. For our model the new sump part number WG01L00289 replaces the original WD18X10026. Dishes & glasses now sparkle. Hope this helps as there was lots of frustration on this end before replacing the sump seen in the photo.

While the microwave works fine, as far as microwaves go; it does heat unevenly but eventually gets the job done, the interior is cracked and shows signs of rust and deterioration. I dont remember ever seeing this on in previously owned microwaves. I would only use it for basic heating and reheating.

I am rating my over the counter GE microwave model no. JVM3160RFSS. Ive had it for over 2 years and its still performing well. Pros: Solid feel, sturdy door mechanism, easy to clean interior, attractive design, fairly quiet, adequate lighting inside, reasonable price, fan works okay for moderate smoke, short reheating times for lighter fare, cooks frozen foods quickly. The integrity of the interior is good with no chipping or cracking. Cons: Fan is inadequate for heavy smoke if searing beef, hot and cold spots while reheating heavier foods such as mashed potatoes or casseroles, controls are hard to see in dim or moderate light. A suggestion to GE would be to make microwaves with optional backlit buttons to see at nighttime or in dim lighting. I like that GE manufactures most of their microwaves in the United States.

Five years ago I purchased a brand-new condo w/ a GE Nautilus dishwasher installed. This machine has NEVER worked right. Issues: 1. The detergent cup that closes, consistently gets stuck shut, hence only half of the detergent gets dispensed and a second cycle is usually needed to get the dishes cleaner. 2. Dishes are never really clean. Theres always at least one dish that has something left over on it, but its usually multiple dishes. 3. Lower rack started rusting out after 3 years of very light use (used approx 3-4 times a month). Loud. Louder than my washing machine. 4. Replacement parts are ridiculously expensive. A new lower rack is approx $100. My condo also came with a GE refrigerator. It too is junk. Never again...

Its a GE microwave/Vent Hood. Inexpensive. We replaced our last one (which was the same one). Nothing special about it. It performs its purpose. The vent hood has a 2 level light and a 2 level vent function.

We have a GE SpaceMaker JVM 239BV 001 over the range microwave purchased about 10 years ago. Within one year of installation the handle snapped - just as numerous people here have stated. I went to our local replacement parts store and was shocked that it cost $30 for a new handle. The sales person said if I were you I would by the lifetime warranty for an extra $3 because you will be back, I sell lots of these.

GE jvm1750sp1ss microwave - bought in 2010, less than 4 years old has stopped working. Lights are on, but when we hit the start button we hear a small pop and nothing else. The clock does work counting down but nothing else. I happen to love this microwave, it was a gift for my wife. It now no longer works and cannot afford a new one. Option 1: replace parts myself for 150.00. Option 2: call a technician for 200.00 plus parts or option 3: do without. Option 4: wait to afford a new one. I guess all things grow old but we should have enough history on these items to post a life span. Well a story like this usually falls on deaf ears but if someone is reading, make the suggestion on the life span or make the parts affordable. Thank you.

My GE refrigerator is almost 30 years old. It's not a frost-free refrigerator, but frost build-up has not been a big problem. I usually defrost it twice a year. I have had no problems with it over the years, other than the light bulb burning out. I would certainly buy a GE refrigerator again.

I am writing this more as an educational notice for consumers of the G.E./Rheem gas water heaters to aid in uninterrupted service and understanding of the water heater. Installation locations: If you have installed your unit outside, all though in the owner’s manual, it states that G.E./Rheem says to never install the unit outside. People that live in warm climates do have their unit installed as such, but in a metal enclosure, of which to the city codes are fine, but again not by the G.E./Rheem standards. So being as this is accepted by city codes, people do and will continue to install water heater outside in enclosures.

We bought a GE dishwasher July of last year. In December it started to shut off some off minutes into the cycle. FOUR months this piece of junk has not been working. Three times someone has been here to say oh it should be working. They are sending someone out for a 4th time now. Should have already been replaced.

I bought a GE dishwasher 2 years ago. The control board went out so I had a repairman come to fix it. They had to order the board from GE directly and it took 1 month or more to get the part. Then it lasted one day! Now they are telling me it cant be fixed. Really??? I expect a dishwasher to last longer than 2 years. I also bought a GE microwave that only lasted 2 years. I replaced it with Whirlpool. GE is crap now and that use to be all I bought. Not anymore. I will never spend any money on GE appliances any more.

Ever since I bought this dishwasher in Jan 2014 it hasnt dried properly. Finally had a tech come out and he told me the water wasnt hot enough. How is it energy efficient if I have to raise the heat in my water heater to get the dishes to dry???? Very dissatisfied! My old dishwasher (with plastic lining) dried the dishes with no problem. I had it for 16 years before I had any problems with it. This new one is a problem from the first time I used it. No GE ever again!

I have had it with GE! Only 18 months after install, my beautiful, stainless, three-rack, GE, top-dollar dishwasher will not turn on. Repair attempts have been futile. Tech said not to expect more than seven years service out of new appliances. Were tossing this junk and buying CHEAP replacements going forward since all we have to choose from is throw away products. OEMs like GE should realize they are shooting themselves in the foot with their planned obsolescence business plan.

Purchase date 4/20/15; Model # GDT 580 SMF ES; Serial # VD776355; Dishwasher wasnt installed until the end of June upon completion of a complete kitchen renovation. Eight months later, on March 1, 2016, the dishwasher was leaking water all over the kitchen! I initiated a service call and the repair man replaced the seal and it has worked without leaking until April 13, 2016. AGAIN a very large amount of water poured out of the left side of the door. The repair man had to return 3 more times and finally didnt have a leak for almost another year. Now, June 1, 2017 my kitchen is once again flooded. This machine is garbage - Very expensive garbage. Dont waste your money! I had previously purchased from Sears and never had a water leak in a machine that was 20 years old.

This GE dishwasher is not designed to last. The exterior outlook is unfortunately poor. It is not water conservative, makes noise during the cycle, does not dry dishes very well which inevitably means a poor conductor of heat. I will not buy anything like this product again! I wish I can get something that is economical and energy efficient this time around. I have spent unnecessary amount of monies trying to get a good dishwasher that can serve the purpose over the years and still cannot get one. You guys need to do the needful by manufacturing good products that consumers like me can depend on. It is high time I get my moneys worth!

I have a GE microwave and was using the exhaust fan on it when it stopped working. I am getting the same message as other folks - KEYPAD SHORTED. I have barely used this product since it is in a vacation home. It looks brand new, but I am really disappointed in it. My cousin told me shes had problems with GE appliances and will never buy another.

Coincidence or not but after posting my review, threatening to get the attorney general involved, putting pressure on local GE distributor through the builder, we have received a replacement dishwasher. This is not a happy ending yet unfortunately.The installer who delivered the unit was filling in for someone who took a day off and was not familiar with complete process. He came to our house at 9am and left at 2:20pm after spending hours reading instructions and maps on how to put things together.The new unit works okay for now but does have a slow drip from the upper left corner. This has been an extremely frustrating battle and we are now more worried about what happens after the warranty runs out if problems continue.One option is to buy extended warranty and give GE more business, second is just to replace it with more reliable brand. I am giving GE two more stars for replacing the problem unit but we are still hurt from the entire process, especially after buying top of the line product. We truly feel that customer service people should have been more sensitive and understanding of the consumer instead of firing back. Their bad attitude really did not help and added more frustration.

GE microwave model JES1344ES. This is a stainless steel with black accent 1.34 cubic foot microwave oven. It looks great. The micro is heavy for its size. The stainless steel is brushed and low luster finish. The door handle is chrome as is some of the other accent pieces. The push button panel is easy to read and has a large knob for making manual time adjustments. The light inside is very bright. There is a rotating platter in the oven compartment that is not knocked off of its guide rollers very easy. The push button panel is a glossy black material that is easy to attract fingerprints. The preset times that are programmed in the microwave is the only part of the product that could be an issue. For example the popcorn button when used has burnt all of the different brands of microwave popcorn that we have tried. It is set about 30 seconds too long. There is no way to adjust the preset time that I can figure out. We set the time with the large knob manually and the popcorn comes out just fine. The preset times for the Auto Defrost are also a bit off. They are not long enough. We also have a Subzero freezer set at minus 20 degrees Fahrenheit so that may be too cold for the defrost presets. Overall the microwave is great except for the preset times that Ive mentioned. We use it daily and have done so for five years. It still looks excellent inside and out.

GE Microwave Model JES1139BLO3, Serial # VS904116B - The above model was purchased at Lowe’s in Ventura, CA about a year and a half ago. In that time, the white coating on the inside of the microwave has been deteriorating, beginning with the area under the turntable and extending out to the bottom and sides of the unit. I am concerned that our food will be contaminated by the particles that are coming off or that there will be a fire caused by the microwaves hitting on the uncoated metal. I do not plan to ever purchase another GE microwave.

Ive had my GE dishwasher for about 20 years. Any appliance that lasts that long deserves praise. It does make some noise but thats to be expected. Drying time is efficient and dishware and glassware come out spotless.

Microwave is a 2001 and works just fine. There are a couple of things that could be better and that’s the exhaust and the lighting outside of microwave. Possibly could be more energy efficient but are bigger models built that way?

I bought a Moffat washer and dryer, and the timer came out of place and burnt on the inside. The timer clips in and if push too hard it will fall out or break the clip. We have extended warranty on it and due the repairman came out twice. The warranty person said it cost more for the repairman than the dryer worth - theres no more warranty. I think the dryer should replace when the timer fell out of place. This dryer should be called back.

We bought our new home 4 years ago & bought upgraded GE Profile appliances. To date, the gas range has been serviced 3 times, the refrigerator too many times to remember & now my dishwasher pump has gone out. We found out the pump just cannot be replaced, but all hoses, etc. must be purchased as well. GE is CRAP & I will never even consider purchasing anything from this company again. Knowing it was bought out a few years ago by Whirlpool (I believe) but still remains under the GE label - consumers BEWARE.

Dont buy one. I bought two last year. The first one completely died before the 60 days were up. I took it back to Sams club and bought another. The tag inside says it was made February 2011, so its only a year and a half old. Under the carousel, the paint is peeling big time. I wrote GE repeatedly, asking if it was still ok to use it. After ignoring me for quite some time, I got this reply. In the notice, they told me to get Sams club to replace the defective and apparently unusable product they are selling knowing it is defective. I love the part where you cant cook something with too much liquid in it. Who does that when they microwave?Heres what they said: Thank you for contacting GE regarding your microwaves and the paint peeling issue. I did some research on it and found that it a common issue among all brands. Excessive heating of un-covered liquids can create a high amount of condensation that the inside paint is not meant to withstand. Minor chips to the coating on the microwaves interior cavity will not affect the products performance. However, if the coating is actively flaking or peeling anywhere inside the oven cavity (including under the turntable), discontinue the use of the microwave and replace it. GE does not have an approved method of repair, and the microwave is not repairable. Please return to Sams club for an exchange, if you are still within the one year warranty. If Sams is refusing to accept the return, contact the Sams Club Support Team at 1-877-885-2787. GE will then reimburse Sams club.

We have had our GE microwave for at least five years. We have moved multiple times and had the power go off but through it all, our GE microwave works just as good today as it did when we first bought.

Purchased GE Dishwasher, Model GDF540HGD488. Its two or three years old and is junk. Top rack rails failing apart, bottom rack sliding rails have melted. Bottom sprayer has melted and wont stay on, incoming water has it bouncing on the bottom of the machine. As the heat dry is in it smells like melting or burning plastic. Dishes are NEVER clean and need re-washing. GE will do nothing, warranty off. Repairman says its just the type it is. Replacing it this weekend with a new Maytag, no way I would ever consider buying another GE product. Worst Dishwasher I ever owned.

About two years ago I moved into my condo and as a housewarming gift my sister gave me money to buy a microwave oven. I bought a GE over the range microwave. Well it quit over two months ago - really disappointed. I bought the next one but now after reading all these similar experiences I am sorry I bought the same problem.

After a short four year history of not cleaning our dishes well, our four-year old GE Profile Quiet Power 6 QP6, model PDW9280N00SS, s/n-VM819634B, overheated and did not shut off and melted everything plastic inside. The house now has a horrible smell of burnt plastic. Ill start the process tomorrow of contacting the insurance company and looking to get this odor out of our home and a different brand of dishwasher into our home.

My microwave is a GE, model JE 1040 made in 1998, which they probably dont make anymore. I use it several times a week, mostly to heat up leftovers and water. Also pre-packaged microwavable meals, such as breakfasts and biscuits. I have cooked different kinds of meat and other items in it many times and am completely satisfied with it. I would be lost without it.

It is functional and does the work. We are impressed with the large drum which takes a good load. It runs smoothly but with some noise. However we do not mind this as the end product is what we wanted.

Purchased an entire line of GE appliances for kitchen after having prior (still working) appliances for 13 years. Have had at least 5 services calls and countless emails and phone calls for non functioning Dishwasher. Here is response from GE Manager: I have reviewed the pictures and no I would re-wash those 4 dishes if they came out of my dishwasher prior to using them with my family. Dried on fruit, starches and dairy are tough for any dishwasher to take off as the sugars in them act like glue. Again for these types of foods we would highly recommend more pre-washing to make sure that they are not left on the dishes after the dishwashing cycle. CAUTION: DO NOT BUY.

GE Stainless steel dishwasher rust inside. Its more show than function. Size is great. GE stated in writing that this is normal for GE stainless steel appliances as GE stainless steel is not real stainless steel. Rust is not covered by GE warranty!

My 4-month old dishwasher started to leak so I called GE to repair since it is still under warranty. Technician said there was a superfluous piece on the gasket which he removed. Dishwasher was fine for about 2 cycles when it started to leak again. As GE do not have a weekend service I had to take a second half day off work. Different technician said the gasket was not pushed in correctly and I should check it each time before running it. Shouldnt this be part of the design - a gasket that stays put?! Ran the dishwasher. Water all over the floor. The new floor that is getting ruined by this clearly faulty appliance.

Our Spacemaker microwave, which was installed over the stove August 2008, suddenly stopped heating food. My husband called GE, and their phone advisor advised us the microwave was under warranty. She said her computer screen showed our product registration, and she also saw we owned three other GE products. Fast forward, the GE repairman came and said the microwave repair cost would be around $400. The heating part wasnt under warranty nor was the labor. Mind you, the entire microwave (new) was under $400. We called the GE service center, and they refused to honor what their representative had told us. The most they offered was 50% off. I dont accept the premise that a new appliance should only last four years. I will replace my unusable microwave with a competitor’s brand and will pledge never to purchase a GE appliance again. I will also sell my GE stock, for I now understand why its going nowhere.

July 4th, 2010 - GE Profile Dishwasher, Model: PDW9200N00BB, Dishwasher had been humming after cycle was over for a little while, this night I walk into the kitchen late and find it full of smoke. Circuit board has a hole burned though it and wiring harness is melted. Never tripped any safety, could close the door and it would come right back on, smoke and all. This model was not on the recall list but I called GE anyway. After describing the fire they send someone out, then they send a new dishwasher out and install it. I assume they wanted the old one to look over or just to get rid of it. New washer installed the end of July 2010, new model number PDWT500R10BB. Today is 2012-02-02 and the new machine would not stop at end of cycle (Got down to 1 minute and stay there for at least 20 minutes before we turned it off). This machine is now making the continuous hum after the cycle stops that the old one did before it caught on fire.Called GE, they said they could maybe go half on parts and service until they checked where I was located. (Wichita, KS. Area population 500,000+) They said that they didnt send factory techs to my area and I would need to contact a local repair service. I pointed out that they had a factory guy for when my machine was on fire and they said it was just a malfunction now, so they could not. No half on the price for repair either at this point. This is a $1100 to $1200 dishwasher with, as near as I can tell from complaints online, a history of going up in flames. I understand things break etc, but when you continue to put out products like this and then refuse to remedy the problem, I and anyone who will listened to me will never own anything GE again.

Of course, I rinse my dishes, but Ive had few incidences of dishes coming out dirty. Hot start, start (long wash), short wash, rinse only and plate warmer. The interior is set up well with a good variety of spaces. I would say its a normal-sized household dishwasher, not compact, with approximately a 24 width, 24 depth and height. White with gray lettering; four buttons and one dial. Simple design that is easy to understand and operate. The run-time of this dishwasher is quite long, and it is very loud.

I work as a service tech for a major insurance company. I am a master tech, and master electrician. The company that I work for owns an apartment complex which is used to house company executives whose offices are located at other sites, but often come to the Chattanooga Site to work short term. I was called to repair an old dishwasher in one of the apartments. Upon looking at the existing dishwasher, I decided to replace with a new one. I received a new GE model GDF 510 PGD 1WW dishwasher on November 8, 2013. As usual I unpackaged the appliance and examined the exterior. Finding no visible damage, and with the help of a master plumber, I removed the old dishwasher, and installed the new one. After all the connections were made, I opened the door, removed all the packaging from the dishwasher, and found the upper spray arm lying in disarray in the bottom of the machine. Assuming that this was the way that the machine was packaged, I installed the spray arm, plugged the machine up and started the machine as the operations manual instructed. The machine would not work. The power lamp would burn solid for a few seconds and start flashing. I tried to start the machine a number of times while reading the instructions, and while my partner read the instructions aloud, but with no results. Finally, I used a screwdriver to hold the door switch closed, pressed the start button and the unit started. The catch mounted on the door would not make the door switch, mounted on the machine body. We tried to adjust the switch and the catch, but with no success.The dishwasher did not show any signs of exterior shipping damage, but for some reason the upper spray arm was off and lying in the bottom of the unit, I found a small piece of broken plastic and a screw in the bottom of the machine, and the door switch would not make. Outside that I have no complaints. I am not sure where this machine was assembled, but it certainly was not equal to the machine that we removed. Thanks GE for making my job harder. I will have to find another dishwasher Monday and replace the damaged one, and perhaps send this one back, but the replacement will certainly be another brand.

Generally ok, but the entire wash cycles take way too long. Certainly much longer than the older models. I guess thats more or less the case with most dishwashers today. It makes me hesitant to use the dishwasher when I consider all the energy it takes to function. I would prefer having a setting for speedier rinse/wash of just a few dishes.

Two years ago, after owning a GE JVM1490 microwave-convection oven (over the stove) for three years, the door handle broke.Let me clarify that I worked for GE first as an engineer, later as manager, for 20 years including 6 in Major Appliances. I am ashamed of what I am reading how GE is treating customers today.I am perfectly capable of replacing the handle myself if I am provided the complete and correct assembly drawings and/or instructions. GE refused to provide me anything when I requested them. The scant drawings and instructions I found online are insufficient. As a matter of fact, the design is so poor that removing the internal bezel, which you must do to reach the handle fasteners, forces you to break the mounting tabs, requiring replacement of this part plus the handle. This was confirmed by the parts store I visited.However, even after removing the bezel, neither I nor another ex-GE appliance engineer could figure out the access to the fasteners. I have glued the handle three times using epoxy and Cyanoacrylate (super glue), but it has broken off a fourth time. I will figure out a way of fixing it before I pay GE close to $100 for both the handle and bezel. And if I replace the appliance, you can be sure it will not be GE.GE should be ashamed of the poor design and deplorable customer service they are giving now. How things have changed!My suggestion is that all with this problem post name and phone number of GE customer service personnel they spoke with.

I purchased new home with new GE appliances. The dishwasher from day one has been a problem. It constantly leaves water droplets inside on top, sides and door of dishwasher as well as all plastics are covered in water after even using heated drying selection. I was told after 2 visits by GE repair that it functions as designed. We have water softener, use rinse agent and quality dishwashing detergent, and the water temperature is within acceptable range.

We purchased a GE dishwasher model GDF 510 in December 2012. We have had three service calls with a fourth one recommended. The first complaint was that dishes were not dry at the end of the cycle. After service calls to replace a faulty heater and install two computer upgrades, the silverware still is not dry. Finally after about 45 minutes into the cycle, it leaks onto the floor. GEs answer is to send another service technician. No thank you! They can have their dishwasher back.

I bought a GE over the range microwave, model #JVM1540DNBB and serial #TS903298B, on January 28, 2010. The keypad shorted out about the middle of July 2012. The microwave just comes on all by itself when nobody is around.

The GE over-the-range, model JVM316URFSS was installed in our new home by the builder. We have been in the house and used the microwave moderately for the past two years. Last night, out of nowhere, the microwave started running. I realized that it was actually heating when the glass turntable popped. I jumped up and opened the door to stop the heating. The turntable was broken. The interior was incredibly hot. Having read several reviews I realize that this is not an uncommon problem. I am going to buy a replacement but I am very concerned by the fact that GE is aware of this recallable situation and continue to allow this product to remain on the market. I will NOT purchase another GE because apparently they do not care. Our house could have burned down had we not be home.

This is a work horse of a machine. I have been using it for 12+ years. Not my first choice, but it was here when I moved in. Still going strong. So why change now, when its doing its job. My first dishwasher choice would have been a Bosch, because they are so quiet.

I bought countertop microwave on 7-2-10 in Panorama City, CA. We were moving to Houston so left it in its original box, but the new apartment had a built-in. I left it in box until May 25, 2011 when we moved into an empty house. I took out my new microwave and used it from 5/25/11 until 12/4/11. I baked a 5- minute sweet potato. Later, I went to reheat coffee and no clock, no nothing. I tried the microwave at different plugs, no response. Then I tried the toaster in the microwaves plug. The toaster was fine so its not the plug. A repairman at his business location said its probably the computer chip. For $95, he would install a new one which would last a lot longer. So now we have disposable GE microwaves.

I am happy with the size quality of service. Gets dishes clean. No spots, not loud thus all awesome job. Recommendations to all my friends. Im very satisfied with the machine.

Dishwasher has been running 3 hours and it still has not finished. It is the loudest dish washer I have ever owned and this is the 5th house I have owned. To top it off I just paid $270.00 for a GE professional to come to our house to troubleshoot our problems and it fix the issues. Guess what, problem not fixed and GE has my hard earned money. Thanks, GE.

Have to rinse dishes clean before I put them in. Otherwise they will not get clean. Does as well as most other dishwashers- until you get into the very upper end ones. The racks are good size. The outside is nice looking.

Purchased a GE 650 dishwasher which we quickly discovered has terrible racking for North American dishware. Also the control panel is overly complicated yet limited to use (always flashes settings even when not in use). Once you figure out how to load dishes into the very tight/ narrow tines they fall over and chip/break. When investigating the dishwashers by GE made in China/Taiwan etc all have same issue. The ones made in USA by GE have wider and longer tines. We have had MANY dishwashers over the 40 years and NEVER had one as bad as this.When calling GE customer service the senior rep was not willing to offer any customer satisfaction as nothing technically was wrong. At one point she stated we had made the purchase so live with it even though it was the wrong choice. We offered to pay for any cost difference, etc. When questioned about GEs interest in customer satisfaction she stated that was not a warranty issue. She was not concerned about a satisfied customer. With that, we will not be purchasing another GE product or its affiliates. What a waste of money.

The side panel of our built-in GE Profile microwave 1999 caught on fire when my daughter was using it. It had a faint glow behind the metal plate. Then, it became flames quite quickly. A flash and pop was the ultimate end before we turned it off during the test. It had been working fine until the fire. This is a definite safety issue. Now that I know the microwaves have been faulty, it makes me concerned about the GE Profile electric stovetop burner. I have noticed it gets extremely hot and doesnt seem to want to turn off!

Microwave oven 2008 - The food doesnt go around anymore. The glass insert does not turn. What can I do?

We bought this dishwasher, with third rack and steel tub, after extensively reading reviews online. We went through Home Depot and had to wait a month for the dishwasher to be delivered. We have had it just over a month now and not only does it fail to get all of the dishes completely clean (even when run on heavy cycle) it NEVER dries even with the dry boost on. We never overload it or load it incorrectly and still there are dishes and utensils with food residue after its done running which takes hours. I predict it will rust out in about five years (planned obsolescence). The only feature Im happy with is that it is nearly silent. Not hearing it run helps to not remind me how much money we wasted.

First of all, I wish I had seen this site over two years ago and I wouldnt have purchased a GE product. But, that is spilled milk. My two year old microwave, GE 1750 over the range, started running on its own. I disconnected it and called GE and asked if they had experienced any problems with their product and if this was a fire hazard, the nice young lady put me on hold and did research and stated that no reports of a fire hazard or running on its own. My husband encouraged me to do my own research and guess what? shocking, I was lied to! There are reported fires on the news and a law firm has a class action lawsuit against GE! I guess because this appliance wasnt in the nice young ladys moms house it wasnt of importance to inform me of the fire hazard? GE is off of my list of products I would buy!

Its an older Hotpoint, and the layout is fairly roomy for a dishwasher of its size. The last apartment I was in had a comparably sized dishwasher that had too many shelving elements that got in the way of being able to just shove some dishes in there. Ive discovered with this dishwasher I need to stick to powdered detergent because the Hotpoint doesnt fully dissolve tablets. It does a fine job overall, though.

I just wanted to make future purchasers aware of an issue I had with the oven light (GE over-the-range microwave model JVM1540DM5BB) underneath the microwave. It is much dimmer than my previous GE oven. I bought it from Lowes and after returning to the store to check a floor model, I discovered none of the models were plugged in so you cant check this out in the store. You only find out once the thing is installed. Lowes referred me to the manufacturer who then told me, after asking if my oven had 1 bulb or 2, the oven was working as designed. How they could definitively determine this over the phone was beyond me, but that was the extent of the assistance.