- A.O. Smith
- American Range
- American Standard
- American Water Heaters
- Bradford White
- John Wood
- Speed Queen
- State Water Heaters
- Stiebel Eltron
- Thor Kitchen
- Air Conditioners
- Appliance Care
- Drying Machines
- Stoves - Ranges
- Tips and Tricks
- Washing Machines
Luxaire Furnace Repairs
If you're looking for help fixing your Luxaire Furnace, look no further! Our comprehensive Luxaire Furnace repair guide will explain common issues, provide tips, and maybe show you how to repair your appliance.
Luxaire manufactures appliances that homeowners have come to trust. Even a trustworthy appliance requires occasional maintenance or repair, however. If you’re in need of Luxaire appliance repair from experienced professionals, your local Appliance Helper can help.
Luxaire Furnace not heating
The igniter gets very hot and glows bright orange to light the gas burner. If the igniter fails or cracks, the furnace won’t heat. To determine if the igniter is faulty, remove the igniter and inspect it for cracks. If the igniter is cracked, replace it. If the igniter is not cracked, use a multimeter to test the igniter for continuity. If the igniter does not have continuity, replace it.
Luxaire Furnace is noisy or loud
The blower wheel blows air out of the furnace and through the house. The blower wheel is attached to the blower motor shaft with a set screw. If the set screw is loose, the blower wheel will wobble on the motor shaft, and the wheel will be noisy as it turns. Check the set screw to ensure that it is properly tightened. Next, inspect the wheel for damage. If the blower wheel is damaged, replace it.
Luxaire Furnace starts then stops
The flame sensor monitors the burner to detect whether or not a flame is present. If the flame sensor is defective, it might fail to detect a flame. If the flame sensor does not detect a flame, the control board will shut off voltage to the gas valve to prevent the furnace from heating. Sometimes, if the flame sensor is dirty, it will fail to detect a flame. Try cleaning the flame sensor with a fine abrasive pad. If the furnace still doesn’t heat, replace the flame sensor.
Luxaire Furnace blower not running
The blower motor blows air through the return vent, past the heat exchanger, and into the home’s venting. First, make sure that power is getting to the motor. If power is getting to the blower motor, but the motor does not run, the motor may be burned out. If the blower motor is burned out, replace it. If the blower motor hums, check the blower fan to ensure that it spins freely. If the blower fan is unobstructed but does not spin freely, replace the blower motor.
Luxaire Furnace blower runs all the time
The control board has relays that regulate the voltage to each component in the furnace. If the relay that controls the blower motor fails while it is closed, it will send continuous voltage to the blower motor, causing the motor to run continuously. If the control board is at fault, replace it.
Related Price Pages:
Luxaire Furnace service
Luxaire Furnace help
Luxaire Furnace assistance
Luxaire Furnace maintenance
Our Luxaire is 21 years old. The only problem is the blower motor failed about the 15-year mark. Just had it inspected & still in excellent condition.
I just replaced a Luxaire after 16 years. Will admit I wasn't diligent about annual maintenance and didn't always change the filter on time, and even with that being the case, I did not have even one repair done to the furnace in the 16 years. Very satisfied!
I replaced a 17 year old system with the new 17 Seer Luxaire equipment. My old equipment was so loud indoors. This new furnace…unbelievably quiet! The outdoor equipment is just as quiet! I love the smooth and quiet sounds coming from them when they are in operating mode. Can't wait to see the savings on my utility bills!
The contractor and his associates were first rate. They did an excellent job and were very professional. They were there on time and completed the job just as they promised. They did not try to hard sell any products. They explained all the products thoroughly and allowed me to decide which furnace fit my needs. I would use them again and highly recommend them. The product I chose works great.
This furnace is so much more efficient than my old unit. It saved me at least 40% in heating fuel in just the first year. It heats quickly and my house has never been more comfortable. I would definitely buy this unit and use the same contractor again. The price was fair and the return on investment is great! Can't think of any downside to this furnace.