The electronics on the first two induction burners failed within six months which was covered under warranty. The second two went three weeks after the warranty and we had to argue with Dacor to cover them otherwise it is a $1400 repair job. From day one whenever you open the oven door the controls and heat shut off. Sometimes it turns back on when you close the door. As for the downdraft, it worked fine until 10 weeks ago when while closing, the cover lip hit a wooden spoon that had been lying flat near the edge. There is no safety feature and the motor continued to try and close the fan. The unit would not respond and would not re-open. The spoon had to be broken to get it out. If this was a childs finger you would have had to call 911. We now have a repair bill of over $350 and are still waiting for 2 months for Dacor to send a part. We will never buy this brand again.

Dont waste your $$ move on to another MFG. I have owned this dishwasher for some time it never worked anywhere near what I paid for it. The glides fell out of the racks. It never finishes a cycle. I have spent $350 for repairs three times and it is still way less than satisfactory. Move on, try a Maytag, Bosch or Miele. Also parts are astronomical and you will need them. If you are thinking about buying this brand google it and read on. We all have the same opinion of the Dacor Dishwasher thumbs down.

The glass plate in the bottom of the oven has been a disaster from day one. Anything that drops on it leaves a white mark that is impossible to remove. It finally became so discolored that I had to have it replaced; over$100 for glass and factory-trained repairman charged $285 to install, a ten-minute job. I wish someone had told me of the problems before I spent over $5,000 on a range which should be useable, not just pretty to look at which also doesnt happen when the oven is all stained. Burners are tinny and dont begin to compare with the Thermador I have in my other home. I will never purchase another Dacor product.

Would highly recommend not spending the money on Dacor. We spent big money on our kitchen hoping for years of trouble free service. We can no longer get parts for our Dacor gas stove/electric oven. The burners click for 2 minutes when you start them. We have gone thru 5 circuit boards. NO LONGER AVAILABLE. The oven light goes on and off by itself. Etc. Etc.

The first F1 Error needed a new membrane repair for $470.00, after 4 years of service. Now, the same F1 error after the new membrane is only 13 and 1/2 months in service and it is now out of warranty. Customer service people are rude and unhelpful but when pressed, they said they might be willing to help after a service tech, which I have to pay for, diagnoses the problem.Even the Sears store people advise their customers not to buy Dacor products and that is sad because it is one of only 2 American made options. Dacor needs to step up their product engineering, commitment to quality and get rid of the rude phone people in Customer No Service. This is not the end of this experience but the only reason I am not junking the stove is because a comparable replacement is another 3000 bucks from another vendor which I cannot afford at this time.The irony of this is that the company clearly knows they have problems but when I asked if the replacement parts had been improved so the problems wont persist, I was told that no changes or modifications to the electronic brains had been made. How stupid is that! They are just asking for more problems with the parts they send you to fix what does not work.

My Dacor Double oven is less than 5 years old. Lately, the broil function has stopped working well on both ovens. I contacted the ONLY authorized Dacor repair center - Home Appliance Repair GTA (HARGTA) and told them my broiler wasnt working well. Their repair technician came to my house, took both double oven doors off in order to give me the assessment – that my upper broil function was not working well. In fact, both upper and lower do not work well but thats a side issue. In the process, the technician broke or did not properly reinstall my double oven door. I called and he returned and again, removed BOTH oven doors. Now, my upper door is working well but my lower door has no hinge and falls hard and heavy. This is extremely dangerous. I have left multiple messages with HARGTA and they are not getting back to me. Ive even contacted DACOR which is only in the US and they havent gotten back to me either. I purchased a Dacor oven to get a quality appliance and excellent after care service. It appears that both the appliance and the aftercare service do not live up to their reputations. P.S. The quote to repair 1 broiler is $750 after less than 5 years of use. That will equal 1/4 of the oven cost in less than 5 years.

Regarding my previous complaint on 3/21/12, I had a Dacor fridge, model #EF42BDCBSS, installed in my brand new kitchen in March 2008 (Ive a kitchen full of Dacor). It subsequently had a problem with the drip pan in March 2009 and was fixed on warranty. Come March 2012, the fridge was again diagnosed with the same problem. The technician told me there had been a design problem, but after three re-designs, it was remedied and should have no further problems once the new part was installed. The bill, $658 and more than half, was for the part! Of course, I was livid because the fridge had been fixed in 2009 and was now off warranty.When I expressed myself originally, I was simply venting about the price of the repair without hope of a remedy. James at Dacor customer service called me promptly that next morning and left a message! We subsequently talked and he immediately got in touch with my local appliance service center. He not only worked out with them refunding my deposit for the part but also ordered two other parts that were necessary in order to fix the problem. The outcome? They fixed my fridge at no charge to me for parts or labor, and all I had to pay was the original trip and diagnosis charge. I cant begin to tell you how extremely happy and grateful I am about this. Thank you, James, for such terrific follow-through and thank you Dacor for being a top-notch business who stands behind your products!

I had an issue with the wall oven light on my Dacor Preference double oven. To make a long story short, after contacting Dacor directly, they made sure that the unit was fixed by providing the part directly to me and confirming that the local repair company would be willing to install it. The oven is 8 years old and in the end, what I spent seemed reasonable to get a fully functioning oven (membrane switch). They were prompt, personal and courteous in their response to me. I came away feeling that Dacor takes pride in their history and their products! They also cleared up some misconceptions that I had regarding the status of their company. Although it was frustrating to have an appliance not work properly, I feel that the customer service Dacor provides makes their company one worth sticking with. That makes a big difference in todays impersonal world.

Dacor range - After I posted my comments on August 8th, I was contacted by Dacor customer service immediately and the new part was sent to me free of charge. I do have to pay the labor, but the part was what was expensive before. They did give me an explanation as to why this was happening - the hinges on the door wear out and the door doesnt shut properly so that heat escapes. Should this be happening with a stove that was this expensive? I dont think so, but I am happy with the customer service I received from Dacor this time.

We built a new home in 2004. All appliances were Dacor. Since then, the oven has had to be repaired 4 times; the microwave had to be replaced; the cooktop has had two repairs and now will not light automatically; and the patio barbeque completely burned up and some of the parts melted. I did report that to the company and to the US Product Safety Commission. We have not abused any of these appliances and have followed the manufacturer recommendations all of the time. Dacor charges top dollar for their appliances, but they are not as good as cheaper brands. If you try to contact Dacor, they have a well-so-what attitude.

We got a U43 relay error on our Dacor oven of 4 years. When we finally add up the cost to replace the part, it will exceed $500 and Dacors only response is, Sorry, it is out of warranty. Of course I do not understand why a relay board on an oven would short out after a few years. Not happy and would not recommend the manufacturer.

My Dacor wall oven does not heat. It is 6 years old and barely used. The technician is waiting for Dacor to get back to them to fix the problem. The technician has done everything they can and it has been four months and Dacor is not responding to fix the issue as its a Dacor problem not a technician problem. (Its a control interface issue, the relay board communicating with machine is not working properly.) I have done my own investigation and they do not reply to customer service e-mails, there is no phone number to talk to someone who could help, just a receptionist who says after 7 years we dont fix Dacor. Again, my oven is 6 years old. I would not purchase this high end product or any product from Dacor ever again.

Purchased a Dacor DT0227B wall oven. The first oven arrived damaged; the control panel was completely off the unit. We ordered a replacement oven which arrived today. Upon turning on the power, error codes C76 and C77 appeared on the control panel display. The installers phoned your service people who instructed them to remove the front panel and look for a loose wire. When they removed the front panel, the entire control board was just hanging free, not secured in place with any screws (it appeared that this was an assembly error). They found a wire hanging, secured it in place, reattached the control panel and applied power. At this time the error codes were no longer displayed and they were able to set the time. When they attempted to start up an oven cycle to test the unit, the Start/Continue button on the membrane keypad was not responding. Another call to your service team determined that the control panel would need to be replaced. 2 ovens within 2 weeks arrived DEAD! The quality is beyond unacceptable. I sent an e-mail to the CEO of the company before I posted this. I received a response from a QA guy. Any manufacturing company that thinks Quality is the responsibility of QA is working with a 1950s mindset!! Dacor is pitiful and will certainly not last as a company with this kind of quality and customer service!!

My Epicure dishwasher is being replaced after 4 years of use. The racks are rusted. It leaks. And the spray arms are broken in two. The dishes need to be completely washed before putting in dishwasher. Do not purchase Dacor dishwasher.

I first bought the low-end Dacor dual fuel range and overhead microwave oven. Within the time frame of 3 years, repairs to the stove cost over $2,500. The stove cost $1,800. Ever single piece of plastic on the stove cracked and had to be replaced multiple times. The microwaves handle cracked 6 times, twice in one week. The overhead trim, which is about 30 by 6 and heavy, fell off and hit me in the head while I was frying bacon. If it had hit the pan of hot grease, I would have been burned. I contacted Dacor and got the brush off. I contacted Fight Back with David Horowitz about the problem. Dacor called me back, bowing and scraping, and we came to an agreement that they would take back the stove and microwave and put the full cost towards an upgrade to their high end model. I am sure you think I was stupid but the stove cooked beautifully and I thought a stove with no plastic trim pieces would solve the problem. Wrong! The microwave control panel has gone out twice, each repair costing around $350. The handle broke 4 times but that was covered under warranty. The front control panel has died 3 times (another $350 each time). The broiler dies each time the self-clean is used and that has been fixed 3 or 4 times. Some computer board on the top of the stove has died (another $400). The enamel lining inside has cracked, crazed, chipped off and rusted. Now, the front control panel has died and so has the one on the microwave. Times are very tough for us now and I cant afford to get them fixed. I noticed that the front panel trim on the top of the microwave is starting to pop out again (plastic fatigue). Hopefully, it will fall off again while I am cooking and hit me in the head and knock some sense into me. If it does happen, I will take them to court.

Purchased Dacor Induction Range w Convection Oven RR30NIS-C in October 2013 and LOVE this range. Accidentally broke the glass on the induction cooktop with falling object mid-March 2020. Only the glass is broken, and all other electronics, induction burners, oven, etc are functioning fine. Called Dacor support to acquire part number for a glass top for repair - obtained part number #701751 superseded by #702285, BUT was informed that the part had been discontinued and is no longer being manufactured or kept in stock. No other advice was given other than to discard the entire $6000 range. Multiple phone calls with service.I asked for a listing of third party part distributors and was referred to four distributors on the Dacor public website and given no other info. I called all web-based third-party distributors I could find in USA and Canada to see if anyone had the part in stock, with no luck. I contacted two technicians to see if they would be able to obtain the part through their channels, with no luck. I am an engineer, so I spent some time pouring over technical manuals trying to find a solution to replace the entire induction range cooktop assembly (top part of the range) with a later model, and although its possible, Dacor would not provide the ability to purchase an RNR30NI range cooktop assembly that could be fit into the existing housing on top of the range. The convection oven is completely fine, and I cannot believe that Dacor has given me no other option but to pitch a six-year-old $6000 range because they stopped manufacturing one fragile part made of glass. I would imagine that many consumers may be in the same position as I, as these cooktops are breakable, and accidents happen. I have reached out to Dacor support desk numerous times without resolution, and I am at my wits end with a $6000 boat anchor in my kitchen. What a waste of money! Poorly done Dacor!I would like Dacor to provide me with some sort of solution whether it be the part required to fix my induction cooktop, or a replacement Induction Range with convection oven, or reimbursement of the purchase price so I can obtain a replacement on my own. If I am not able to find a solution to repair my range, I will never buy from Dacor again! Dacor will discontinue easily broken parts without warning! You may spend thousands of dollars and not be able to repair your appliance after warranty expires!

We purchased this oven February 2009. On 6/7/11, we had to replace the touch pad assembly. On 12/16/13, we again had to replace the touch pad assembly with a cost of repair to this point of over $900.00. The over cost $2,395.00 when purchased. On 3/16/14, while on convection/bake the oven switched over to broil. On 3/20/14, a repairman came to the house. The condition did not replicate but the repairman, in conversation with Dacor, determined that the fix, if this should happen again, would require the replacement of the relay board and ERC control at a cost of $700.00. On 3/27/14, while on convection/bake, the oven switched over to broil. I called Dacor and was forced to leave a message.

My Decor Epicurian oven and range has been a nightmare from day one. I have had the oven for about 8 years and had it repaired so many times I have lost count and had spent at least $2000 on repairs. We have experienced motherboard burn out, membrane failure, temperature control malfunctions, error messages that cause incessant beeping. Nearly all of the problems that have been described in this list of complaints, I have had the problems themselves multiple times! Now, I am panicking a bit because I decided to use the self clean function on my oven this morning and now, I have read some sad malfunction stories following the use of this feature. I am so torn about whether I should just cancel the cleaning process. I do not want to risk having the oven malfunction again, but the thing really needs to be cleaned.

I wish I had read all these reviews of Dacor products before being duped into paying for a high end wall oven. As many others have mentioned, the electronic panel design is faulty. I paid $1000 to have it replaced once. Now it is broken again and the alarm beeps constantly. The reply from their service rep was that they havent had any recalls of this product (in other words, no ones house has burned down yet). He also admits that he wouldnt buy a Dacor oven unless he had money to burn. Well, my money has already burned and so have I.

Worst oven Ive ever purchased by far. Pay big bucks and get junk. About 2 times per month, the oven will not heat up. I cant count the amount of wasted food and dinners out, because it does not seem to ignite, only warm up to about 100 degrees. I contact the appliance repair company and it works when they come out, so they dont do anything. I will never, ever buy another appliance from this brand.

Follow-up to March 31 posting: In 2001, we installed two Dacor wall ovens and a gas (converted to propane) cook top. The cook top has been problem free and the brushed stainless steel surface still looks like new. Both ovens however, at that time, were problematic during the two year-warranty period. Knowledgeable service people were hard to come by in our region. After numerous service calls, Dacor replaced one of my wall ovens at or around the three-year mark (outside of the warranty period). That particular unit had only one minor issue since then and Dacor replaced the appropriate part free of charge. The other original unit has been problematic since the beginning. The latest problem being the internal light going on/off for no reason and then a lack of response to light button on the front control panel.Long story short, I posted my frustration here on March 31 and was contacted by a Dacor rep within two days. He asked me for detailed info on the problem and located the unit in their files. Some of the past repairs were known to Dacor, but others were not since we just did them ourselves. I was asked to send a detailed description of the current issue along with pictures, which I did. Based on Dacors analysis or the pictures and the exhibited problem, they sent me, free of charge, a control panel membrane, a door gasket and a set of door hinges. We installed these items and the unit is now in full working order.In looking back over the past years of problems with this particular unit, its clear to me the issues all stemmed from an original broken door hinge. It was compounded by the fact that the service and repair folks at the time considered the door gap to be within tolerance and we did not discover the broken hinge until the door glass shattered and we needed to replace it, which required removing the door. Anyway, at this stage in the game, I am very pleased with Dacors response. It is my impression that they are trying much, much harder to stand behind their products. So, while just a short time ago I would have never considered another Dacor product, when the time comes, they would still be on my list of considered vendors because when these ovens work, they work great.

I have an older cooktop. Yes it is 15 years going strong but I have ran into a few issues where I know the repairs would be pricey but especially the parts. After talking to a few representatives, they truly want to help you. Nothing is free and I don’t expect it to be, but I am glad they they helped me get my cooktop back to functioning again. I hope someone finds this helpful before reading or writing bad reviews.

We have an 11 year old Dacor double oven with convection on top. The relay board malfunctioned and there are no parts to repair this. All Dacor would tell us is that they dont carry the parts anymore. Evidently, they are not required by law beyond about 8 years and that appears to be all they do. Our appliance repair person even contacted a company that rebuilds electronics and they cant get parts for this board. It is unbelievable considering what we paid for the oven. So we now have to replace it. Dacor offered us a discount on a new one. Not good enough. I cant imagine putting another Dacor product in. Two appliance service people have told me that Dacor has this reputation and they would not put them in their own houses.

We purchased the Model MOH130S in 2006 from a very reputable distributor of high-end appliances. In 2009 we required a service call to deal with temperature control. The oven was out by more than 40 degrees Fahrenheit. This resulted in a relay board, item 101559, to be replaced. Dacor was nice enough to cover the cost of the board, but not the cost of the $152.00 service call. In 2013, guess what? Relay board, this time out by more than 50 degrees, item # 101559 required replacement again only this time it was not covered and cost of $628.00. Here we are, 2016 waiting for the service provider again as temperature is out by over 60 degrees. Roasts, Turkeys, Chickens and everything else have been dying slow deaths in this unit and are awaiting yet another bill to deal with temperature control. Dacor will do nothing until another $150 service call confirms the problem. Hmmm! What to do?

We remodeled our kitchen in 2006. I spent a fortune on a Dacor dual fuel gas cooktop with electric oven/convection oven. My Dacor problems seem so normal I mostly deal with it. My 2 biggest complaints are the glass oven door is not airtight, it is darkened between glass, very hard to monitor my baking. And the temp gauge has always been off by 15-25 degrees. I use an in oven temp gauge, which has been calibrated so I know it works. If anyone is planning on a Dacor, you will get the best looking range. It just wont work.

Dacor Distinctive Series Range model DR30D - One week after the appliance warranty expired, the oven stopped heating. The repair man replaced the circuit board. We still got a code 33 when we try to get the oven to heat to 400 degrees. Called customer service, they said to flip the breaker to the unit off for a few minutes. Seemed to help but we do not use the oven much, as we also have a Meile microwave/oven that we love and use that more. Then I cleaned the oven using only the ovens program. That locked down all of the gas cook top knobs. I called the repair service, it snowed on the Saturday of the appointment. They cancelled. I did not check the stove on Sunday. On Monday the repair service walks in and simply turns it on, no problem. VERY FISHY!!! I have heard the manufacture can control it by computer chips. This appears to be very true. Now the stove does not heat past 250 degrees. After speaking to a few people it appears this is a very common issues. Dacor is a lemon. Do not waste your time and money.

We purchased a DACOR double wall oven (MOH2275) in April 2012. We are waiting for service to arrive for the fourth time since we purchased the oven. I find this unacceptable. We have had 2 other ovens in the last 30 years and they did not need any service. In general I have found appliances to be of such reliability that I dont get extended warranties. DACOR gave a 3 year warranty on this oven and now I know why. Hopefully this service will fix it for a long period of time.On the positive side, the oven really works well. It is so well insulated that we feel very little heat coming off it. One serious flaw its overall operation is the reheating of the oven. If I bake something at 350 degrees and then want to reset the over to 450 degrees, the oven does not go into preheat mode and does not let you know when you reach the required temperature. I am hopeful this will last awhile and not have to be replaced for what we paid for it.

I purchased most Dacor appliances when I built my home in 2015. Their induction cook top and dishwasher kept breaking down one by one. The first time the repair service was done well. Early 2019, their cooktop broken down again and I still have the half broken cook top for almost 4 month now. We have been emailing back and forth, firstly Dacor promised to mail me the parts, but then a different customer rep reached out saying I have to take the broken parts out and mail it back to them before they can send me the replacement parts. That means I would have to live without a cook top for a while. There is even no estimation when I will have it fixed!! Dacor dont value their customer and Im comfortable to say it is the worst product quality and service I have experienced in my lifetime. Never recommend it to anyone!!

I purchased a Dacor Renaissance range for our new home. What a waste of money. Though I have not had any major problems with the performance of the range yet, besides uneven baking, the design is not user-friendly. To begin with, the gas burners share a grate. So when cleaning, you have to remove the whole grate on one side. The controls for the burners & griddle are very hard to see & I have to bend over to see which burner Im turning on. The oven racks are a joke. The two glide racks are very bulky with sharp edges. It is difficult to change the heights or to remove them for cleaning purposes. Though there are three racks included, it is impossible to bake with all three in the oven.I have a GE Monogram that I had purchased two years ago for another home, and I love it The Renaissance & Monogram are similar in price, but I unfortunately, listened to the sales person & let them talk me into the Renaissance. I realized my mistake in buying a Dacor immediately & contacted the appliance store. Even though the Renaissance had not been used, they would only give me a token amount of money towards trading it in for a Monogram. So, I am stuck with a range that causes me to swear under my breath every time I use it. Dacor could learn a lot from GE.

We have a new (one year old) home with Dacor appliances. The microwave oven went on the blink the first month but was repaired by a factory approved repairman. Something to do with the computer. Now the double oven will not hold a temperature. We set the oven at 420 and it only goes to 360 even though the readout shows 420. We just decided to skip the repair process and bought a new Wolf oven. This is our second Dacor within the past two years and both have had the same problem. Dont waste your money.

Dacor Double Oven Model D0230 - I have had my oven since November 2011. I purchased an extended warranty at the time of buying the oven. Right after it was installed, I called and said they needed to come and adjust the temperature control. It was off at least 50 degrees. It never held the correct temperature. Since July, we have had to replace 2 relay boards, two other parts that should take care of erratic temperature. Then I noticed the gasket was turning black in the corner and my glass pack in the window was steaming up and not clearing. The extended warranty would not cover the glass replacement and I was charged $126. They said it was cosmetic, but this was so bad that I couldnt see through half the glass. The steam stained the glass and you could not clean it, because it was inside two pieces of glass. Do not buy a Dacor oven. In 38 months I have so many repairs that I have lost track.

My Dacor Preference 30 double wall oven (model PCD227R) was installed on 5-14-2004. On 12-31-2007, I replaced the upper oven high limit switch for cost $146.56. On 5-19-2010, I reset the lower oven high limit switch for cost $95.00. On 8-27-11, I replaced main control panel (Bezel Assembly), whose parts cost $271.10. On 12-14-2011, I replaced the main relay board for $214.02. On 1-16-2012, I replaced main relay board again, and it is under warranty. On 2-3-12, I replaced upper oven temperature sensor for $32.09. I am awaiting authorized Dacor service technician to calibrate both ovens.

Thank you for your attention. Since my post, a resolution has been reached and Dacor will be replacing my range with a new one. That is much more representative of the pride and reputation of Dacor. The executives were very responsive. Perhaps front line agents are not empowered to make these decisions, however, in my case, the escalation brought the matter into the right hands. Happy with the direction towards the final outcome, not the 4-month process that discounted the reputation and my perception.

We remodeled our kitchen less than 5 years ago. As we have owned restaurants in the past, we wanted commercial quality appliances. I was looking at Sub-Zero and Viking or Wolf. Unfortunately I took my Home Center convince me to purchase A Dacor package. That was a mistake. Even though these appliances cost as much as the those brands, the quality is not even close. After spending $22,000 on appliances I have quickly discovered that these appliances are junk. First the microwave began to arc and nearly caught fire. Even when they installed my cooktop. I noticed that the burners in the middle were marked incorrectly and the blue LED indicating the burners are on was burnt out.After only a few years, now my ovens are not working. And right before Thanksgiving I am without ovens. My old ovens were almost 50 years old and worked fine. These $6000 plus ovens are not even 5 years old and are down. I am kicking myself for not going with my original plan. If you are considering Dacor, I would not recommend.

We bought a new house a couple years ago, and the kitchen came with a suite of new Dacor appliances - range, fridge, and dishwasher. They are all terrible.The led indicator on the dishwasher is scrambled. The icemaker in the fridge clogs up into a solid block of ice. We had this fixed, which involved a new control board and some caulking, but the problem returned not long after. The knobs on the range feel like theyll snap off any time. The lights in the oven arent seated properly and they interfere with the oven racks. It takes forever to get up to temperature. And Im starting to think I have a gas leak. How can these products be so expensive and such utter garbage? Oh, but they have wifi!

I purchased all Dacor products. First Dishwasher went out, had purchased warranty. Came out 6 times to fix it, filed complaint with Better Business Bureau. Finally got dishwasher replaced with a Kitchen Aid. Thank God for the BBB. They help people. Then my stand alone range with 6 burners had one of the burners go bad, the appliance co. fixed it. Then the oven relay board went defective. Had to order part over $400.00, no warranty. Then wall oven Relay Board went out, 2016. Paid over $460.00.Less than 12 months later relay board went out again. They said Sorry, no warranty. Ordered part said it was $500.00 + to replace. The appliance repair tech ordered wrong relay board. They called me today and now said its going to cost $650.00, no warranty. Do not buy Decor products. They are horrible. I feel I am being ripped off by Dacor and feeling untrusting of the Appliance Co. I may need to file another complaint with Better Business Bureau. Buyers beware!

I purchased the 30" All Gas Heritage Range, the Convection OTR, and the Counter Depth Refrigerator! I am obsessed with all of these gorgeous Dacor appliances! From the brass caps on the range, to the chilled water pitcher in the door of the refrigerator...Dacor has thought of it all! I have enjoyed cooking more and would recommend these products if you are wanting to update your kitchen appliances!

As a contractor, we were fortunate enough to build our dream home which was completed in 2005. After much research and many show room visits, we purchased Dacor appliances for our kitchen. As the saying goes, if I knew then what I know now. Our biggest (note I said biggest, not only) issue is with our ESC130 oven. If you own this oven, do not, repeat, do not, use the self-cleaning mechanism. I have had this repaired once and then replaced once (along with a relay board). I seldom use this because I know when I do the lock mechanism will continue to cycle until it is replaced. This means, while I can still use my oven, I have to time when I open the door based on when the lock is cycling in the unlock position. I must also turn the oven off at the circuit breaker or listen to the continuous warning beep that the lock is cycling (as if I didnt know).After repairing this feature once, I next choose to have the mechanism replaced and Dacor offered me a discount on the parts (the oven was and still is out of warranty) at a cost of more than $500.00. This is on top of what I had already paid to have it repaired just 18 months earlier. I feared using this feature again as I didnt want a repeat performance. After cooking macaroni and cheese yesterday, I felt I really needed to clean the oven and made the mistake of using the self-cleaning feature of the oven. I dont know why I was surprised when the locking mechanism refused to stop cycling.I contacted Dacor today only to speak with the rudest customer service representative I have ever encountered, Steven. No last name. He is the only Steven who works there. He refused to listen to me, spoke over me when I did try to talk, and did not allow me to speak with anyone else. There are no supervisors available on Fridays and he could not transfer me anywhere. I left a message for someone else to call me (they did not). I called back later that afternoon and was given the name of a supervisor, Nhi. She was not available and I spoke with another customer service representative. I learned that Dacor is aware they have a problem with this locking mechanism and are trying to correct it. This got my hopes up, thinking that the company would now do the right thing and replace this mechanism at not cost to me, or at least at no cost for the parts. Not so. Even though Dacor knows there is an issue with this mechanism and they are supposedly trying to correct it, all they can offer me is a discount on parts. Really? Wow! A discount for a part that you know doesnt work properly and probably wont work properly because they are still working on the problem? I just really dont know what to say. Is this supposed to make me happy as a customer? Would prospective customers want to buy a Dacor product knowing that Dacor is more than happy to sell me a known defective product at a discounted price and they should expect the same? It is probably needless to say that I would urge all prospective Dacor owners to not waste their money on any Dacor product as they do not care about their customers. I will certainly be doing my part to warn others and hope this serves to warn others as well. Dacor has a lot to learn in terms of building even what could be called a good product and standing behind what they sell as well as becoming a customer service oriented company.

It give the peace of mind, knowing that having a Dacor cooktop (RGC365) I have one less thing to worry about it. Food is always on time, and my wall oven is so simple to use and clean. Like I said one less thing to worry about it. I been a Dacor customer for over 12 years. There is no need to look any farther. My next kitchen will be a Dacor Set.

Most of my life, Ive always bought pretty low end appliances, and theyve always worked pretty well. When we remodelled our kitchen, we decided to go with a high end Dacor stove, and its been nothing but trouble. After just a few weeks, the igniters started to fire constantly on some burners. It was still under warranty, but it was very hard to find someone to honor the warranty. We got that fixed, then the oven light started to come on and off randomly. After our experience with the first problem, we just disconnected the light and let it go. A few months later, the bottom shelf jammed, and there was no way to collapse it to fit in the oven. This product is total junk. Dont buy it!

We moved into our newly built home in April 2012. I purchased the Dacor 30" microwave drawer to complement a 30" electric oven that is installed just above the microwave. I am very happy with my purchase, it is stylish and works well. The drawer is spacious, I can fit multiple food items in it and they all cook evenly. We use it daily and couldn't be happier with it. If I ever move, I will purchase this microwave drawer again.

I completely gutted my kitchen on 2/22/92, and purchased a Dacor CPD230R double oven. Whenever I used the self-cleaning function the next day, F0 would appear. I would have to get a repairman to come to my house. This cost me a fortune. For one year, I just used the bottom oven. I finally called Dacor, and complained. I wrote a letter to Mr. **, and wanted satisfaction.They decided that I could purchase a new, better oven for $1,480.00. This was 1998, so in 6 years, I spent $3,680.00 for 2 ovens. After 5 years, I started having the same problems. Every time I used the self-cleaning function, F0 would appear. I just totaled my bills for the new, better oven, and I have spent $963.00 and it would be more, but I figured out, if I pressed cancel and held it, the F0 would disappear. So every time I used the oven, that is what I did. This would last for 8 months. The oven completely shut down, and I could not use the top or bottom. I just had a repairman here, and he said i need a new membrane assembly, and latch. They were supposed to call me with an estimate. They just called, and said the part is no longer available. This is upsetting. Reading the reviews, I see I am not alone in my dissatisfaction with the Dacor oven. Now, I will be redoing my kitchen.

Motherboard on my favor wall oven has been replaced twice. Repairman said not use the self-cleaning feature as that will cause too high of heat and melt the components. Seriously, Dacor? We spend this kind of money and have these type of repair issues constantly. Just glad I finally was told what might help resolve this - I’m ready for a new oven because of all these problems.

We had a ongoing problem with a wall oven that was purchased in 2006. The most recent complaint was a oven glide rack that was not working. After complaining about it to one of their staff, they listened to our frustration and are sending us a new rack at no charge. My hats off to the great people at Dacor. Thanks for your understanding. Al

Front bevel of my first rsd30 range purchased in California in 1999 cracked within nine months. Dacor said it was a defect in the design and would fix it for free. I sold the house in 2001 but the range was still not fixed. I moved to Nevada and bought a new rsd30 range and same thing happened within six months. It took a year to get it fixed at their expense. This bevel also cracked again for the second time in March 2011. Their response to this was to offer me a new bevel for $180 and I would have to pay for the installation. I declined the offer. The bevel is still cracked at this time. At the same time, I bought a PMOR30 over the range microwave and the front handle broke at least four times. And finally, the whole thing broke down and was not repairable. In Aug. 2008, I contacted Dacor and they agreed to replace it with a new DMT2420 over the counter microwave for half the price ($390). Last week, this one blew up on me. Sparks were coming out through the side and a big hole in the removable shield and burn damage to the wall of the unit. I do not believe this unit is repairable. I contacted Michael at Dacor. He apologized and said that theres nothing they can do about it as it is out of warranty but they will look into it. What I want at this point is my money back that I paid for ($390) and for them to pick up the unit and get it out of my house. I will never buy another Dacor product again.

Our refrigerator is 5 years old and has had a problem with icing up in the freezer area, resulting in a loud noise from the freezer fan. We originally called Dacor for service but they could not get to it for 2 weeks. An appliance repairman installed a new heater for the defroster. This only worked a short time and happened twice with a cost of over $1000. A couple of months ago, it happened again, and we were able to get a hold of ** at Dacor customer service. She knew exactly what was causing the problem. She ordered the parts and directed a factory-approved repairman to install over $800 in parts and we are confident the issue is resolved. Thank you, Dacor, for standing behind your products.

About a month ago then again 2 weeks ago, I would hear a beep (not while I was cooking) from the stove. I went over and all elements had turned themselves on at HIGH. The only way I could turn them off is to repeatedly push and hold the child safety button. Very scary! If I had left a pot or pan on the range top, who knows what would have happened. It did it occasionally with 1 burner twice more. Yesterday, the range top started cycling every 90 seconds, on then off, then on, then off. I shut it off at the circuit breaker twice thinking this is a way to reset electronics sometimes. Once for 2 minutes then again overnight.I tried cooking on it this morning: on and off and on and off again. It is shut off at the circuit breaker awaiting repairs. I am a renter so am spared the repair bill but not being able to cook (of course it happened on Easter weekend!!) is a major pain. It is 10 years old this week the landlord told me, but I used to cook on a stove that was 60 years old and it worked like a champ.

We had our range oven for less than a year and the front electric panel cracked, there is no stress to this area. I called the company and they admitted the entire panel was defaulty and had a recall. They did replace it. Within 5 months the new one cracked in the same place. This time they stated the unit was out of warranty. I told them the same type of recalled panel was installed. They said I could buy a new one. Ha! Since then many more cracks. I will never buy anything made with the Decor brand nor do I recommend them! Happy shopping.

The enamel on the bottom of the top oven has blistered and the metal beneath is exposed. If the oven is heated, there is a chemical smell. This is such a dangerous situation that the ovens (double) are being removed as I write and will be replaced with a different and more reliable brand.

I paid over $6000.00 for a Dacor EF48BNDBSS refrigerator and have had nothing but problems with this item and the other Dacor item (dishwasher) that I bought when I had a new kitchen built for my new life of retirement. The first refrigerator that was delivered did not work when it was installed and was returned immediately. I had to wait for Dacor to send another one and I have had to pay several service calls each time since that point. I am disgusted that I paid over $10,000 on two appliances from Dacor and neither of them has ever worked even at a low grade basic level. Both of my items have been discontinued and Dacor reimbursed me for half of what I paid for the dishwasher, which did not even cover all of the repair calls that I had paid for ongoing service. At that dealing, I got tired of paying for repair calls for the refrigerator due to excessive icing in the freezer; supposedly there was a quick fix right after I had the unit installed and it did not fix the issue. Now, there is another quick fix that Dacor suggests and that will cost me $800. Really? I dont think so. In fact, I have researched this issue and have found that this quick fix does not solve the problem either. In addition, I have called Dacor numerous times about the refrigerator door not sealing and the refrigerator making all kinds of strange noises. They told me it was the seal, so I had the seal replaced and that was not the issue. Then I paid $235.00 for a service call to look at the seal and he said that this refrigerator has known problems for hinge issues and he attempted to fix the hinge and left and the problem continued. Between the hinge issues, the constant icing issues in the freezer and the food icing over as well along with the trays and inner shelving of the freezer, the refrigerator sealing and the hinges working, and the constant crazy noises that the refrigerator makes, I am ready to file a lawsuit for a lemon of a product. This is the second product that has recall issues and multiple problems. I am sure that with my documentation, a judge would have no problem agreeing that I have paid way too much and put in way too much time and energy into getting a decent appliance into my kitchen. I would never recommend Dacor to anyone. I am dissatisfied and refuse to pay another penny for service calls on these appliances that were installed in 08/2012. At this point, my refrigerator is unplugged and unusable and I am using a small refrigerator that I bought at Costco for $300.00 thirteen years ago that has never had one problem.

Im planning a kitchen remodel and stumbled on this site. I have a Dacor dual fuel range (stove wont light, oven wont hold temp), hood (light wont stay on consistently), microwave (replace once, okay now), wall oven (panel out) and warming drawer. Only the warming drawer is working correctly. I live in rural Kansas and I cant get anyone to do repairs. I really like the design but... its time to move on to a new brand!

I was very upset when I tried to get service on my Dacor range. I made a complaint to ConsumerAffairs.com and was subsequently contacted by James ** of Dacor Customer Service. He offered a telephone number to support a local appliance repairman and arranged for me to get my parts at a special pricing. This worked out great and my range is now fixed. I am a happy Dacor Range owner now. It was just too bad that I had to make a complaint on the internet before I got help. I hope this incident will encourage increased cooperation from Dacor in the future.

2017 purchased 36” range. First year- self cleaning overheated, replaced part. That was in 1 years warranty. But now: only 3 years barely: (I dont even cook much). Oven turns off by itself if I open the door. Oven does not turn off when I am done cooking. If I cook 450f pops warning of temp overheat. Called ABT service (this is where Dacor said) it cost $219 for a service guy to call dacor and to give me answer: I think it is android board. I have to buy a board. Plus per Dacor this board will not have wifi. So there is no Discovery- paid extra for extras I can not have...

I purchased a DACOR PGR-30S LP in 2002. It has had a number of problems due to poor design that required replacing the control panel as well as other parts. However, it has recently developed a gas leak and thus is no longer usable. To fix the gas leak, you must take off the top burners to get to the leak and make a repair. UNFORTUNATELY, DACOR has to make room for new parts and no longer makes the O-Rings required. Yes, apparently a $10 O-Ring takes too much room seven years after I bought my range. So, in 2009, DACOR discontinued making the O-Rings and now I have a very expensive paperweight that I have to take to the dump so that I dont blow up my house. I wouldnt ever buy a DACOR again. The customer service it terrible and they cant even be bothered to carry simple repair parts. Buy a Wolf or some other high end stove because DACOR is literally a piece of junk!

This week Dacor installed my 2nd replacement gas range. I remodeled my kitchen 3 years ago and chose Dacor because I had a great experience with their appliances in the past, had their oven and stove in my kitchen for 15+ years and never had a problem. With the first new range, the oven started to automatically shut off due to excess heat escape, so the safety feature would kick in and shut the system down, in addition the knobs would become very hot even when the over was used briefly, 12-15 minutes. I was very impressed and happy with the customer service through Dacor, they immediately gave me a brand new over. Exactly another year, the new oven had the same problem, door begins to not hinge properly and heat begins escape, knobs get dangerously hot.This week Dacor very kindly, replaced my appliance with the new Dacor Renaissance 36. I used the oven for 12 minutes on 400 and the entire exterior is dangerously hot. I do not have any children, however, if I did I would be terrified that they could seriously injure themselves. The exterior of an oven should not become hot like this. Has anyone else had this issue with Dacor? I feel they have been very responsive with regards to customer service however I want an appliance that is safe.

We purchased a under counter Dacor oven. The timer started given problems, tried contacting Dacor. The rude customer service advisor first talked to me like a police interrogation, then said sorry cant help. A joke of company with cheaply designed products. Never again.

I purchased a 30 Dacor dual fuel range and matching hood in 2004. I paid $4009 for the range and $948 for the hood. The range and hood have been nothing but problems. I wrote to Dacor in April 2009 detailing the problems with the range with service history dating back to 2006. Problems include overheating when cleaning which is a safety risk, replacement of cooling fan, ignitor assay, part # 92309 membrane, and replacement of relay board in 2007, 2009 and again December of 2011. I attempted to purchase a Dacor extended service agreement in January 2009 but was declined due to the ranges past history and its age. I recently found this site which indicates that other consumers have had similar problems with Dacor products. Dacor has lost me as a customer as I will never buy another Dacor product! I have been disappointed and frustrated with their lack of response and support. I finally purchased a GE service contract which has helped absorb some of the cost of ongoing repairs. The overhead lighting has long since gone out in the hood. I was told the hood needs to be disassembled to replace the lights. Dacor should step up and support its products. When most people put out $4000 for a range, they expect to get a quality product that will last 15-20 years. With Dacor, this has definitely not been the case!

Our 30in Dacor double ovens are approximately 12 years old. I feel they operate adequately. However, not better than our much lower end appliances we previously owned. My main complaint is the self cleaning function. My old ovens self cleaning worked much better! With our Dacor ovens one must take out the racks and clean them by hand. This is very difficult and time consuming. I used the 3 hr option to clean my oven that was moderately dirty, mainly from cooking a prime rib over the holidays. After the 3 hr cleaning the oven was still very dirty with splatters and grease. Im now cleaning my oven again with a second 3 hr cleaning cycle. I know at the end of this second cycle I will need to do a lot more cleaning by hand! I hope Dacor has improved their inadequate self cleaning feature. If it hasnt been improved, I really cant recommend Dacor ovens.

We thought we bought a quality product when we remodeled our kitchen two years ago and put in a $3000 30 inch wall oven from Dacor through their dealer Friedman’s in Knoxville. We had heard for years that their products were top notch and high-quality. I find it interesting that the oven has a self-cleaning function. However Dacor Technical advised me that if you use the self-cleaning function you will create too much heat and destroy the motherboard. Wonderful input after the fact. The oven now does not keep a correct temperature and we are advised that our oven is two years old and out of warranty and we should not have used the self clean function. Really? Why is the button even there. Do not under any circumstances purchase any Dacor product. I feel comfortable in saying Samsung will add absolutely nothing to the quality or service. The lack of customer care and concern is beyond reproach. One star rating is way too generous. How do you just walk away from your products. We used our clean function exactly once and nobody ever said it was a self destruct button.

I purchased a 48 Dacor Epicure stove in October 2010. We moved into our home in November just in time for Thanksgiving. We remodeled the kitchen and the stove is the focal point. When I heated the two ovens, the pre-heat mode stayed on but the ovens went to 600 degrees plus. My oven thermometers only read to 600. That happens every time and the fans stay on for hours. After many service calls, we have determined that the oven is going into a cleaning mode every time and is wired backwards. Dacor is ignoring me.

Updated on 11/29/2018: Further to my recent review of my Dacor wall oven, I went to a high-end appliance store yesterday to research replacements for my microwave, oven, warming drawer installation (so, yay, I get to spend $13,000-plus to replace items I have had for only eight years). I cannot verify the accuracy of this, but the salesman explained the problem. For a period of time, Dacor and Viking used the same third-party supplier for their relay boards. Unbeknownst to the companies, the supplier substituted a part that was later discovered to be defective. Unfortunately, all replacement relay boards contain this part, so the problem will recur repeatedly, as many on this site have discovered.As bad as the cost of periodically replacing the board is, the unreliability of the oven is worse. As happened last time, mine works OK sometimes, burns everything other times, and struggles to get to the desired temperature other times. And because the behaviour is unpredictable, it cannot be reliably recreated when a repairman visits. I have had one email from Dacor and I responded with the information requested, then nothing. I suspect that they know they cannot fix the issue in a permanent way, so theyre just hoping all of us with this defective part will just go away. It looks like newer models that look like mine are still available, but I refuse to pay $5,000 on the off-chance that it has a better relay board. I am looking at Miele replacements.Original Review: I have had two Dacor wall oven, microwave, warming drawer installations. The first one was only a couple of years old when we moved, and Id had to replace the microwave, but I put it down to a power surge in the house after an outage. I have now had the same set in my new house since 2010. I have had to replace the microwave again, but not because of a power surge. It just stopped working. The oven has been a complete nightmare. The probe broke and although I had it repaired, it never worked properly, but the worse problem is that I am about to have to replace the electronic board for the SECOND TIME. When the problem occurs, the oven heats up to the setting but the element just stays on. I all but ruined an expensive cut of meat on the weekend – with company coming, no less – and just had to throw out a batch of muffins. I am considering tearing out the whole installation and getting another brand that doesnt destroy my food. It would probably be cheaper than having to fix the oven every year or two and replace the microwave periodically. These appliances are garbage.

I have been very disappointed in the reliability of our Dacor refrigerator, model EF42BDCBSS, purchased in 2007. The first circuit board went out in 2008 within 6 months of the initial purchase. A replacement part could not be located. It was still under warranty so they replaced the whole unit. In 2010, we had to have another repair to regulate the temperature of the freezer. Last week (October 2012), the circuit board went out again! Even though the unit itself is less than five years old, it is no longer under warranty. Dacor goes by the original installation date. I contacted Dacor and spoke with LS who basically stated that all they could offer was a discount on the part. This repair is costing us over $650, not including the loss of food. We paid to have the part second day. When we called back the next day to get a tracking number for the shipment of the part, we were told by another representative that the part had not shipped because it was out of stock in the default warehouse. He was able to locate it in another warehouse and get it shipped the same day. I called LS back and she stated that she never promised when it would ship, but when it did, it would go second day. I would not expect this type of repair cost and attitude on a refrigerator that was over $9,000 when new. Now, I am concerned with the liability of our range and microwave, which are of the same Dacor brand. The main reason I took the time to write this email is to make retailers aware of the situation and ask that you seriously look at the reputation of the Dacor appliance line and decide if you really want to promote this product to your customers. Dacor could care less about their customers and/or reputation.

We moved in our new home in June 2019. We had purchased 2 Dacor dishwashers, 2 ovens, a gas cooktop and a microwave. All the appliances are beautiful. That said, both of our dishwashers leaked so bad we had to stop using them as they were damaging our wood cabinets and floor. Dacor sent service persons out after multiple calls and replaced the seals, but they still leaked. Our cabinet company that sold the Dacor appliances stepped up and replaced them both with Bosch dishwashers.Our Dacor Refrigerator went out in mid February and will not cool anymore. After 2 hours on the phone with a Dacor representative, we finally were able to schedule a service person to come out a week later (Dacor has very few support companies so dont plan on anything happening too soon when there is a problem). Was not able to repair the fridge and said it could be another two weeks to get the part and return. That said our service person is a great guy and cares, but has to rely and wait on Dacor for responses and parts.Our ovens take twice as long to cook as any other oven we have ever had. We are asking them to look into that as well. Overall, very disappointed. We understand having problems, but expect Dacor customer service would be much better and support their own field service persons and clients or at least act like they care. Not looking forward to calling them back to see why we need to be without a fridge for 3-4 weeks total....

This is my first DACOR product. Did not know too much about the brand. Did some research and read reviews online & decided to try a microwave in a drawer since I needed to save counter space. We use it all the time and so far it’s worked great. The color blends well in our kitchen even with the microwave being the only DACOR we have. DACOR customer service has been great and professional when I needed to register the unit. I would recommend the DACOR brand to anyone when they are looking for a premium appliance and anyone who comes to my home comments about how lovely it is. Thanks DACOR.

Ive had this range for two years and am replacing the control panel for the second time. 1st time during product warranty and second time out of warranty. The range is beautiful but apparently the electronics are bad. And to add insult to injury Dacor doesnt stock replacements but has them assembled when needed. Estimated wait time for a new panel is 3 weeks; so no oven for 3 weeks and now not a lot of faith that the new board will be any better than the last one.

We acquired a $7,500 Dacor refrigerator when we bought a house this year. The fridge was only 5 years old. First of all it made horrendous noise when operating. Secondly the ice maker didnt work. Thirdly the freezer cooling unit died last week. How can a $7,500 refrigerator be designed so badly? I found out through Dacors authorized service company that it was quite likely the freezer could be fixed with a $400 part and some $250 in labor. The technician hinted that this problem was quite common with Dacor refrigerators. I contacted Dacor and suggested that their Internet reviews were terrible and they should help defray the costs of their premature failed unit. I was thinking that for a 5 year old product they should reimburse 50-75% of the total cost to repair. They said they would give me a 25% discount on the retail value of the parts only. In other words - I would be on the hook for at least $600 of the estimated $700 fix. This was a slap in the face. They dont seem to realize that their companys future business is only built on satisfied customers. I cant believe such expensive equipment can be so poorly designed and supported. Mercedes Benz... they are not. Lest anyone think that I am a frothing upset complaining consumer - I will tell you that I am currently retired, and formerly CEO of a $200 million public software company. I know something about building a business and I know something about focusing on customer satisfaction. I would urge anyone reading this review to stay away from all Dacor products. The Company has shown itself to be undeserving of any American consumers business!

We bought a 36 inch Dacor range with oven last year, around September, when we moved in to our new house. We tried to turn the oven on Thanksgiving day for 10 people, but it would not work. We called for service, and they replaced the circuit board. The repairman turned the oven on, and it worked fine. We never used the oven, just the burners on top, because we have a second smaller oven, we like to use for every day cooking. Then came Christmas day, and we were having 30 people over, so we went to turn on the Dacor oven, but to our horror, it did not work again. We have owned this oven for a little over a year, and have tried to use it only twice. In that time, both on holidays, with a lot of people to feed. This time, when I called for service, they told me I will be charged $198, because when they tried to get Dacor to drop that charge, they said no. We are very disappointed in Dacor for not caring more about the customer.

I purchased my Dacor Epicure Range 8 years ago when I remodeled my kitchen. My other appliances were made by GE and Bosch. Ive had to service my GE appliances a couple of times in the last 8 years, but it is the Dacor that has given me the most grief and it was the most expensive appliance purchased. It has never been reliable with regard to convection baking. Initially I thought it was my inexperience with a convection oven. I read everything I could get my hands on and kept trying...after talking with a friend who does quite a bit of baking I realized its not me, its my oven. Then the real problems started. First it was the broiler/ignitor, next it was the membrane in the keypad. Two months later it was the relay board and this time it was the broiler/ignitor....Again! Started calling Dacor when the relay board went out because at this point I had spent $1,000 on repairs....after I had paid $4,000 for the range itself. For the last two repairs Dacor has paid for the parts, while I paid for the service call and labor. This has reduced the cost of my last two repairs by about 50%, which is very helpful. However, Im still very disappointed in the product. I spend a good deal of time in my kitchen and do quite a bit of baking, cooking, and canning. I thought that if I spent more money and bought a high-end appliance, it would serve me well. At the rate that Im going, I will need to purchase another range, unless I want to keep throwing money into repairs on this one, which I dont. I will not ever purchase (or recommend) another Dacor product again.

I bought DCM24S DACOR 1.5 CU CONVECTION MICROWAVE-SS and after few months of using this product its banded on the back wall of the microwave that supposedly resulted from improper turntable placement which caused the turntable tray to make contact with the back of the oven. The quality of the product is very poorly, dont buy Dacor product!

We moved into our home in 2012 and have had nothing but problems with our Dacor refrigerator (Dacor Model EF48DCBSS). Our issue is the drain pan heater AGAIN. This problem is, water that collects in the drain pan freezes and eventually builds up to a point where the fan motor starts hitting it, sounding like a helicopter landing in your kitchen! Weve had this problem repaired THREE times by TWO DIFFERENT repair companies to the tune of $1000. Both repair technicians said it was a design flaw and this problem would continue to happen regardless of how many icing kits were replaced. So a $7000 refrigerator will cost us $1000 a year to keep running?!?!?! After much research, its apparent we are not alone with this problem. We also had a Dacor microwave just STOP working (model #DMT2420S). It was only 8 years old. Our Dacor oven range (model #ER48DSCH) has two ovens and only one side retains the heat. The main side gets to about 300 degrees and then the temperature starts dropping. Here is the breakdown of costs for our so called high end appliances. Dual Fuel Range - $10000, refrigerator - $7000 (annual repairs of $1000), microwave - $500 (had to purchase new microwave $600). PLEASE LEARN FROM OUR MISTAKE AND DO NOT PURCHASE DACOR APPLIANCES. We have a refrigerator/freezer that we bought from Sears SIXTEEN years ago for $500. Still works like a charm! And thank God we have it, because it has had to be our backup for our $7000 Dacor.

Updated on 02/23/2021: Its been several weeks since I first posted. The only reply that Ive received was an email via this site that requested information from me on my claims. The info was provided the same day. A week has gone by since I provide the information and I have yet to hear back from Dacor. Not even a were looking into your issue. What I did receive was a notice from Samsung (who has acquired Dacor) telling me that one of my service tickets has been cancelled. I dutifully called the listed number to get more information... only to be told that the Samsung customer service rep could not help me and that I needed to call Dacor. Ive tried to approach this matter with humor up to this point but I am out of patience. Given the price I paid for these products, I expected a premium customer experience... the experience I have received has been abysmal.Original Review: I did not think that a customer experience could be this AWFUL or that a vendor could seem to care less than Dacor cares about resolving my issues. After 5 months, the exhaust downdraft that we purchased still does not work and Dacor either does not respond or - when I can get someone on the phone - I get any number of standard excuses (parts shortages, Covid, port backlogs are delaying deliveries, the integration with Samsung, etc, etc). I am also missing basic parts such as shelves(!) that should have been installed during the original installation. The retail partner (Specialty Appliance) does not seem to have anymore luck in getting answers.

When our installer removed the packing material, he saw that the oven glass was shattered. Dacor said they would fix it, but wouldnt tell me how. I had to call the local repair shop to see what parts were being shipped. Only the glass! Not even the whole door. The idea that they would take apart and reassemble a brand new oven and consider that acceptable service makes me angry. This is supposed to be a high end company. I responded that this was unacceptable since the oven had obviously been dropped (shatter pattern spreads from the lower right corner of the glass) and might be a safety hazard. No response yet. Ill update this if/when I get a response.

I own a complete Dacor Kitchen, with many appliances. They are the highlights of my Home. Great features: fast induction cooktop with an efficient silent hood, versatile refrigerator, reliable oven, and of course the always dependable dishwasher. This is My Dacor Kitchen!

Arrived in good condition and so far works perfectly. Delivery was delayed by one day because of the incompetence of my local mail service. I bought this microwave, as others have described, to replace a 13 year old Dacor that had not really died but had lost the electronic screen. We put magic marker numbers on the display screen where the numbers had been 5 years ago and kept using all the functions. I decided to replace as, without the display screen, I could not do anything semi sophisticated with this microwave but its motor and microwave capacity was still going strong. This model fits perfectly into the previous 24/27 trim kit. Unfortunately our other trim kit is white to match our old microwave. Decor only has stainless steel now. And the new trim kit for this microwave is flat without the vent slats (plus costs over $300!). From the placement in our cabinet, I think the vented slats are really important to dissipate heat and am puzzled by the change in design by Dacor. The slats are a little tedious to clean but as a TV is above the microwave and an oven below I want the heat to have a better place to go. Ebay has the old trim kit in stainless steel but so far the expense seems excessive for just the outside piece. The internal support bracket for the new microwave is exactly the same as for the previous model so the only part of the trim kit needed for my microwave is the outside frame. This newer model works very similarly to the older version. I am delighted Dacor still makes this microwave to fit my space 13 to 15 years later.

We purchased this unit 7 years ago, just a family of two with visiting grandchildren. Unit came, had a crooked door and a bent latch, which we had serviced and supposedly corrected. When self cleaning the latch still made grinding noises. Over a year ago the oven stopped working period. A December service call said needs a new latch, sensor and display -we are now in 4 figures($). Oven operates for month and a half. January 2019 Service call now new door latch, relay board and main wire harness 4 figures again double! Oven stops working yesterday (June). Service call today new latch, motherboard and something else and another 4 figure repair cost. Same repair parts same problem! Patience is a virtue, but repair costs are sinful! Next step, Boat Anchor! Problem from the beginning and still a problem now.

We purchased a Dacor Double Wall Oven in late November of 2019. I liked the oven and it functioned well until October of 2020 when the oven quit working due to a control panel issue. We were told the part was on back order. I continued to check with Dacor customer service and was continually told the same thing -- it was on back order. Never once did they call me to give me an update.In December of 2020 when I called I was told there was an update. The part was no longer on back order it was no longer in production, they no longer make the part. They would review the file to see if they were going to give me credit for the oven or get me a new oven. I contacted them again today and was told it was still under review and it could take them another couple of weeks to decide what to do. I asked to speak with a supervisor but was told that there was not one available. The person I spoke with today said that she would call me next week to give me an update. I appreciate her concern but that does not get me closer to a working oven. I would not recommend Dacor to anyone, customer service is terrible.

We bought 3 very expensive Dacor appliances when we built our home 12 years ago. They have been a total disappointment. The microwave was replaced after just a couple of years when it just stopped working properly - including needing to stop it by opening the door! The wall ovens have needed many minor repairs which have amounted to several hundred dollars after labor charges. I see on this post others have had to repair the hinges! Ours have been replaced twice! The broiler came loose and was hanging on one side. The internal light also goes on and off by itself - sometimes in quick succession. At times, it stays on and cannot be turned off by the light button but by banging the front of the oven! Ridiculous! The cooktop cooks very unevenly. It goes from simmer to boiling over. The ceramic material did not hold up very well either. It is supposed to clean easy. But there are spills that have left permanent stains and we will be replacing that as well. We have also had Customer Service tell us items have been discontinued so we have no choice but to replace these appliances since replacement parts cannot be purchased any longer. This is a warning to anyone considering Dacor - DONT WASTE YOUR MONEY! There are far better appliances out there!

Dispenser spits out ice cubes onto wood floor everyday. Told it is design issue and nothing can be done. We have to constantly check the chute is empty after used but we can be nowhere near the fridge for hours and hear ice pop out onto floor. My grandson has tripped and fell and me also. Im more concerned for safety than anything. Also our hickory wood floor is concern.

Dacor 48 dual fuel range - Only 3 years ago, we purchased a Dacor range that is beautiful and worked great for 2 1/2 years. During the last six months, I had the led lights go out on some of my cooktop knobs and my oven has started not baking evenly, much as described in a previous post (half of your cookies can be burnt and the other half dough). A serviceman has been out twice and I have been made to feel that basically, I dont know how to use this oven or dont know how to cook. Funny that has only been in the last 6 months. I cooked great with the range for 2 1/2 years and have 20 years of cooking experience, but obviously, I dont know what Im talking about. To replace a led light bulb, I had to purchase a $300 control board part (that Dacor did discount) plus a $100 labor. It ended up being a $250 light bulb fix that has exploded to a potentially additional $600 problem. When taking off the range lid to replace the lights, I am now told that 3-4 burners have to be completely replaced and this again is my fault somehow because the metals fuse together and that is known by Dacor to happen, but my service tech said its because I dont clean my range well enough. This still makes no sense. And to fix the oven problem, it might be the control board? Lets throw my money at it and see? All guessing, the serviceman, Dacor, etc.! So now Im stuck with a parts bill of over $1,000 (Dacor did discount this to about $300) plus $200+ in labor, another guess. This just seems ridiculous to change a light bulb and guess at an oven fix for a 3-year old range that cost as much as a car! Im so irate over the whole issue! What a mistake Dacor was.

I purchased my Dacor range in 07. After running the self clean cycle today, my oven wont heat up using convection or regular bake. Keep in mind, I had the entire electronic guts of the oven replaced in March 2011, 6 months ago after the same full failure. I paid $6,500 for this appliance. I wish I had my old GE oven back. This piece of equipment is only 4 years old. My husband and I dont use the oven often. What a huge disappointment! I will likely spend the next few days on the phone with customer service.

I built my home in 2003 and installed a Dacor 30 wall oven. After several years of poor performance, we started to get an error message. Dacor suggested replacing a board for $300. That didnt work so they had me replace another $300 board. That didnt work so they told me I needed a new front panel and it would run about $1,000. That board is on back order and they dont have a replacement date. Thinking that its bad business to sink $1600 into a troubled product that has terrible reviews on the internet. We found out that once you go with Dacor, you need to stay with Dacor due to an unusual, nonstandard size.Thinking that Dacor has improved their product we ordered a brand new $3,000 Dacor RO130 30 wall oven. It arrived promptly and I removed the defective $3,000 oven and put in the brand new $3,000 Dacor RO130 oven. What I got was a dead brick. The Dacor customer service has been awful, and will not allow me to talk to anyone in their technical side. The oven is getting power. Dacor customer service wouldnt help me unless I could prove that the unit was getting power. So I had to get an electrician in to prove that I had properly wired the 4 cords that came off the original defective Dacor wall oven. Get service help? No chance. I live 100 miles from Seattle and no one wants to work on Dacor. So here I sit with a $3,000 brick. No service and Dacor has no clue on how they will service this wonderful $3,000 RO130 30 wall oven that is an out of box failure. I dont see how a company that has this bad of a product, two generations of defective ovens, bad customer service, reluctance from the repair community to work on their products will be in business much longer. If you are considering Dacor appliances, consider the problems that I am having. The nonstandard size of their ovens will lock you into future purchases to replace their products that dont last 10 years.

Dacor refuses to take responsibility for defects in their products. Our wall oven required two cooling fan motors and two relay boards over a relatively short period of time. In addition, all of the sensors had to be hard wired when the oven stopped working, and our service technician was informed by Dacor that moisture tended to get into the sensors on these ovens. We spent nearly $1500 on these repairs. Reaching a customer care representative at Dacor can take upwards of 20 minutes. Phone calls are not returned. Customers are left to pay the cost of defects in Dacor products.

I would never buy another Dacor product. The microwave totally crashed and now the oven will not heat. I have had contact in the past regarding repairs and they are outrageous. I plan to replace both items rather than paying unreasonable costs. Very unhappy.

Dacor 27 electric double oven unreliability. Almost from first use the Dacor electric double oven has been plagued with problems including but not limited to door not locking when self cleaning, not self cleaning, door not unlocking upon completion of self cleaning, and filter issues. Since purchased in 2013 the top oven has been used between 75 and 100 times; the bottom oven less than 25 times. Yesterday the oven died. First error message U43 relay board. Second U60 cooling fan. Worse when the control board responsive/froze circuit breakers were needed to turn oven off.Repair estimate is $1600 plus tax. I intend to replace the overpriced and unreliable Dacor with a Kitchen Aide at approximately 13 the price based on customer and Consumer Reports reviews plus a new one year guarantee. I do not recommend the Dacor double oven if you are a serious cook and/or frequent user. Brand name and styling are less important than product reliability and useful life especially when you can purchase the former for two-thirds less money.

We purchased this high end Dacor range (Dacor Renaissance ER30G) new in 2011 from the Appliance Loft here in Cincinnati. It was dropped off and installed and would not operate right out of the box. A repair was made and everything worked (unless you count the indicator lights on the knobs, they all went out after approx 14 months). This past November the oven went dead. A1 appliance came out: Determined new control board needed, ordered and installed. Thanksgiving Day, oven dead. A1 comes back, reset the High Temp Fuse. Oven dead 4 days later, A1 returns with a new HTF. Dec 22, Oven dead. As soon as The holiday is over we will call another repair shop and start looking at replacing this unreliable piece of eye candy. Open comment to Dacors design engineers, quality control engineers and management. You should be totally ashamed about this product youve designed. You are supposed to represent the best in American design and quality and this falls below that of low end appliances out of China. See you in small claims court.

Bought to replace 15 year old same model and I'm hoping I will get another 15 years out of this one as well!!! Great price and delivery!

When we recently remodeled our kitchen, we replaced our Dacor double ovens that we had had for 15 years. These were great ovens and not one problem with fairly heavy use, so we bought the Dacor Modernist double ovens. The ovens are usable, but they are the worst engineered product I have ever experienced. First, there is no clock on the stove because as I was told the clock would etch the screen if it was on 24 hours a day. Second, the sound the timer makes is so soft, even on the loudest setting, cannot be heard in any room but the kitchen, so I paid a premium price to carry a timer with me, so I know when my oven is done baking. Third, if I turn the oven light on, the timer either stops completely, or it resets to the original time. Fourth, the oven buzzes when it is cooking. Fifth the user manual is useless and there is no video or online information on how to use this oven that is not user friendly.Finally, I have talked to Dacor and have had the repair person here, but he knew nothing about this oven. I am sorry every time that I use this oven that I did not buy my other choice, which was the Woof double ovens, but we thought this would be wonderful product, like the wonderful product that our previous ovens were. We also thought Dacor was a family company, but is now owned by Samsung. What a disappoint these ovens have been. The engineering for this product is a disgrace for any company and I no longer see the Modernist products advertised and it may be because it is such a poorly designed product. I never met a computer that I did not love, but this is not the electronic wonder that was advertised when we bought the ovens.

Got a great online deal on Dacor LP gas range. Was new but had dinged side panel according to store. Couldnt see the ding in photos and it would be hidden against cabinets anyway. Range is finally delivered and is new as advertised. Works great for a few days but then the oven wont hold temperature and then wont light. This is when the nightmare begins. Samsung now owns Dacor and getting to the right people to make a warranty claim is insanely difficult. After making the repair claim we get notified that there is no warranty coverage for service as this was not a new unit. Pardon me but we have the sales receipt showing that it is with full factory warranty. They finally agree to accommodate us and then repeatedly cancel repair tickets. After many calls to fix this, they now tell us that no service center will come to repair the range! They offered a refund minus some sort of discount based on a stove being used for a period of time. Oven stopped working a week into having it and they want to DISCOUNT a refund! Made BBB complaint and their response was they would have someone reach out to the customer. Today they did that and we are still at no resolution. Told them they have 3 options, fix the range, replace the range or refund us completely and I will make arrangements to fix the oven. They say there are no ranges in inventory to replace this one with with. No one inside the US will call or reach out to fix this fiasco and we are left with someone that is not allowed to make decisions that speaks english as a second language. Sad thing is that its a basic range that at first seemed to be a great design and would be great to have in our kitchen. Its now endless headaches because Dacor refuses to step up and remedy a defective oven part with a service call from someone that would require likely higher pay than their network providers.

Like many of you on this site, when we remodeled our kitchen in 2000, I researched and decided to shell out the extra money for the highly recommended and higher priced Dacor everything. We got a double oven, glass 30 cooktop and an exhaust fan. 12+ years later, I wish I had bought GE! My ovens have had so many problems I cant even count. Basically, the temperature doesnt hold correctly. I have used oven thermometers and my husbands fancy gauge to check temp. I had a whole transformer and control panel changed out in hopes that it would correct the problem, but it didnt. I think it has something to do with the self-cleaning. I think it gets so hot that it fries the controller. I never use the broiler so its not like I left the door open and wasnt supposed to. This afternoon I set the oven to preheat to 350. I set my little cakes inside that I was making with my grandson. About 5 minutes later, it smelled like something was burning so I checked the little cakes. They were already charring on top and then I noticed that the top element was fiery red, basically on broil! What the heck?! This is ridiculous! Im not going to spend another $500 for another repair! I am waiting to see what the repairman says.On another note, my stovetop cracked twice! The last time, Dacor was nice enough to sell one to me at cost and my husband was able to install it. It didnt match the old one and I was told by Dacor that they dont make them anymore and that is made by a third party supplier now. The old one had a textured finish and this one is just very shiny and scratches so easily! I hate it. We also had a retractable exhaust fan put in because the stovetop is in an island. Every time I turn it on, my basement smells like whatever is cooking. Now the buttons dont work anymore. That is unless I jab them so hard with a sharp object that it finally makes enough contact to work! This is another part that we got at cost that my husband had to crawl around and repair that still doesnt work.So, all three Dacor appliances we bought have turned out to be very disappointing purchases. Dacor should stand behind their products better, offer longer warranties or better yet, build better products! I would never recommend these products to anyone!

We replaced a Dacor with this new upgraded Dacor. I accidentally started a fire in the last one...my fault not the units. Ours fits very snuggly into the wall which was the primary reason we went for the Dacor brand. Other than having to take off the little rubber pads/feet, it slid right in and we were back in business.

I emailed Dacor for information about how to get my range fixed and was amazed. My questions were answered complete with numbers for model and needed replacement parts along with contact information for local service folks. Amazingly good service. Bravo, Tori **! Give that woman a raise!

Warning: Warning, safety hazzard for all, adults and children. Recommendation: The knobs should be set on the top of the stove, not the front where children can reach. Control knobs should click when fire and gas is turned off, and highest flame setting should be at the end of the turn just like a clock. I inherited this range as new owner of the house. Today I used the high flame option of the gas stove. When I was done with cooking, I turned off the gas according to the knob position, front of the turn. Later I discovered the range was not exactly off. It was still hot but no flame could be seen.I checked by sight the control knob position, it was set incorrectly in off. Then I touched it and realized the knob actually has a bit more to go to the end, slightly before the off position. Therefore it continues to release gas with unobservable flame. This knob does not click when user turns it to the off position. It is just a silent knob with an inaccurate cue of a heavier black line for off and on indication. Besides, high flame setting comes at the beginning of the turn of the knob rather than the end, it is counter intuitive to our mind of increase heat by turning the knob further on, like our clock. Oven racks are hard to put back after cleaning. Once a rack almost tumble out while food was sitting on it.

I have owned a Dacor dual fuel 6-burner range for several years. I paid approximately $5,000 for the product. It has proven to be totally unsatisfactory. The gas burners click and make noise whenever you try to turn the burners down to a low temperature. The cook top is very hard to clean. The range is a constant problem. It smells bad, does not heat up promptly, and the broiler feature is always a problem. A gas oven is supposed to heat to and keep a constant temperature - the Dacor does not. The broiler will not cook food evenly or well. The door to the oven will not close properly and is constantly partially open. The hinges do not seem to work properly.Most importantly, I have tried on many occasions to get Dacor to do something about the defective product. They have been totally non-responsive. When I did finally get somebody to come and look at it, they spent about 2 hours cleaning it, accused me of using the wrong cleaner on the cooktop, and presented me with a bill for $800. I asked if they would just give me my money back and take the defective product with them. DONT BUY DACOR.

Purchased Dacor Wall Oven EO130SCH in 2011. Rarely used, so never used the self cleaning function. Occasionally wipe with microfiber cloth, eco-friendly cleaners like vinegar and Bon Ami and elbow grease. First problem in 2017 when the oven would not heat up, just before I had guests coming to stay with us. Dacor repair personnel could not make it out for a few weeks, so repaired the issue myself by resetting the thermostat with some creativity and effort. Next problem in 2018 with a U43 relay board error. Can use it for a while if turn off the power to the fuse box for a while, but in 2019 it also started making a clicking noise, and basically not functioning right before I needed it for a party. Cant replace the relay board (which costs more than $300 for the part itself) without pulling out the oven. But why is the relay board failing so quickly? Is there a fan cooling issue? Have talked to Dacor. Poorly designed, poor quality. I would never recommend Dacor.

I bought a Dacor Epicure 48 range in 2003. It has never worked correctly. I read many other complaints on this same range. I had the burners replaced and I still have to light them with a match each time I turn them on. The oven temperatures were never correct. Nothing bakes properly even following their directions. It bakes very uneven. The hinges are sprung/broken (as the doors are too heavy for the lightweight hinge they use). I have had numerous service calls over the years and still not a good oven or repair. I too am very disappointed in the fact that this product is a lemon and they will not replace it.

We remodeled our kitchen and decided to use the range as the focal point of the room. The decision to go with a Dacor ER36DSCH dual fuel range over comparable Wolf and Viking models as well as a Dacor heating drawer was made, a decision I have regretted since. Our unit keeps blowing the baking element ($200) which routinely fails at the most inopportune times. To date I have replaced four and the Mrs. recently informed me that the oven is once again not heating properly. Thankfully, I am competent enough to diagnosis and repair it myself and did a thorough operational inspection and cleaning which revealed the broil element ($180) had also gone bad this time. My wife hates this oven and unfortunately it sits right smack in the middle of our beautiful kitchen to remind us of the bad decision we made. In fact, we are now at the point where we are considering replacing it and sending it to a scrap yard where it belongs. Avoid this brand or it will cost you.

I purchased this upgrade to my kitchen renovation. The stainless steel stove has a great look, but that is all it has. This is my third repair (with much difficulty). The same problem - the bake ignitor goes bad and sends gas smells throughout the kitchen. On Christmas day, after preheating the oven, I opened the oven door and the inside was one large flame. The heat was intense and my right arm got hot from the heat. I immediately closed the oven and cancelled the bake setting. When I called Dacor the following morning, I thought I was talking with a robot. No emotions, no sense of caring. They must be programmed. I got no satisfaction. I said, Do you understand? My stove went on fire and on Christmas day. My family was not sure if they should leave my house. I am extremely disappointed with Dacor.

We moved into our home in July 2012 and have had nothing but problems from our Dacor refrigerator which was manufactured and installed in this home in 2007. The appliance repair company has been to our home approximately five times in the five weeks since we moved in. Initially, the problem was with a leak in the cooling system which took the technicians about 16 hours over three visits and $1,400 to sort out. Currently, we have been without a visit from the techs in two weeks (our longest stretch since moving in) and the refrigerator is leaking from the ice dispenser and making a motorized noise so loud. Initially, I thought a motorcycle had pulled into my kitchen. Needless to say, the technicians are on their way back.

Updated on 05/11/2021: I wrote a review about my terrible Dacor stove, and I was amazed when I was notified within a couple of days that Dacor wanted to help resolve my issue. I was asked to provide some basic personal information, which I dutifully supplied. That was weeks ago and I havent heard a peep since, and I doubt I will. Clearly they do this just so they can mark these reviews as Resolution in progress to make it seem like theyre doing something to help. But as far as I can tell its nothing but a smokescreen. Dont be fooled by resolutions in progress.Original: Our Dacor stove is the worst stove I have ever owned or lived with in my 50+ years. Within 2 years after we bought it, the oven had stopped working twice and 2 of the 4 knobs broke. (Ive never had a knob break on any stove before.) Luckily an appliance repair person (not specific to Dacor) was able to get the oven working both times but told us replacement knobs were not available. We have tried generics but nothing fits. I have been juggling 2 knobs on 4 burners for more than 3 years now, and STILL Dacor has no replacements available. Six months ago we inquired again and were told they had a new model of knobs available that would fit, but we ordered them and they were on back order and never became available. Meanwhile Dacor had already processed our payment for them (which is illegal, I believe) so we had to deal with getting that refunded because our hope of the knobs ever being in stock was gone. This is also the loudest electric oven Ive ever owned. It sounds like convection is on every time you use it, whether or not its actually set on convection. That lasts for 20 minutes after you turn off the oven, too. Also, periodically the stove emits a loud BEEP and resets its computer for no apparent reason, sometimes when Im cooking (oh, you had a timer going? TOO BAD - who knows when it will be ready now!) and sometimes when the stove isnt even on at all (just thought you might like to reset the clock - AGAIN).Furthermore, the oven door has a special design with an open space at the base that allows dog hair to get sucked in from under the stove and collect between the 2 layers of glass. So we get to view our food through dirty HAIR. Apparently thats why the oven is so loud, because it takes a lot to suck up all that hair from under the stove. This can be cleaned, but you have to remove the door to get to it, which is not easy - I cant do it myself. Its so embarrassing when we have people over for dinner; I just hope nobody notices the hairball in the oven door. After reading through the other Dacor reviews I consider myself lucky to be able to cook at all. Buyer beware, dont EVER buy anything from this brand. Its total (expensive) crap and customer service is nonexistent.

I have had nothing but trouble with a wall oven I bought in 2010. Basically just bad electronics. I finally replaced the oven in 2014 and had to get another Dacor to fit the opening. The new unit still does not heat evenly and is consistently off by about 50 degrees. Customer service is not helpful at all. Local repair shops cant really fix issues. Terrible company. Cant figure out how they stay in business.