My Dacor wall oven does not heat. It is 6 years old and barely used. The technician is waiting for Dacor to get back to them to fix the problem. The technician has done everything they can and it has been four months and Dacor is not responding to fix the issue as its a Dacor problem not a technician problem. (Its a control interface issue, the relay board communicating with machine is not working properly.) I have done my own investigation and they do not reply to customer service e-mails, there is no phone number to talk to someone who could help, just a receptionist who says after 7 years we dont fix Dacor. Again, my oven is 6 years old. I would not purchase this high end product or any product from Dacor ever again.

We purchased a home with brand new Dacor appliances. Within 1 year, the relay board had to be replaced. One year later, the relay board has to be replaced again. Its $600 each time for parts and labor... The part alone costs $500. The company does not warranty the relay board. At this point, we should have purchased a new wall oven. They claim these are superior appliances. Our gas stove top works well, but the wall oven and refrigerator have been nothing but problematic. We will never purchase this brand again.

We have 3 Dacor appliances that we purchased new when we remodeled our kitchen a few years ago. Our cooktop’s igniter continually clicks even when it is not in the light position. This only happens on the front 2 burners (the back 3 are fine). We have cleaned the unit and cleaned the igniters over and over. We have had 2 authorized Dacor service companies and another company look at our unit. Two said no fix exists; the other replaced a part after talking to Dacor and that did not fix it. When I called Dacor, they noted to get another service company and call them when they are here. I am concerned that this again will not work and I will have to pay another service fee.When they were here I asked them to replace a light in our double oven, but they noted they would have to remove the oven from the wall to do that and it would be costly, to which I said no thanks. Is it true that the oven has to be removed to replace a light? Another issue is that our double wall oven’s upper unit only gets warm to about 200 degrees. Another issue is that the microwave door open button does not move the door, we have to push it and pull the door open by hand. I have turned to Dacor service and to our local service techs and we are at our wits’ end. Any help here?

After less than a year after installation the oven continues to operate poorly. Its been recalibrate twice and a new control board installed. Did I mention the board had burned components? It still does not operate properly. Its at least 25 degrees off. Everything takes way longer to cook than it should. Thanksgiving was 2 hours late. Christmas was the same. Entertaining during the holidays, embarrassing. Now Dacor wants pictures to prove to truly see how poorly the oven is operating. I thought I bought a quality product but I was wrong. This is just following suit with the Dacor refrigerator I purchased and was replace months later.

When I bought my house, the previous owners told me that theyd been having problems with the Dacor oven. They had purchased a replacement burner and prepaid the Dacor authorized service technician to install it for us. We have worked for three years now to get Dacors authorized service representative to install the part for which he has already been paid, and have been using a toaster oven to prepare meals for a family of four the entire time. The oven will heat to 135 degrees, then either shut off completely or immediately switch to broiling mode and burn whatever is inside it. When I called Dacor to see if they could help with the service issue since the technician was authorized by them, they told me it was my problem, not theirs. Although if the product they manufactured wasnt faulty in the first place, it wouldnt be anyones problem!

I purchased all Dacor appliances when our home was built 3 years ago. The Refrigerator has been serviced 2 times already and now requires manual defrosting every month to keep it functioning. Now the double ovens broken! These appliances are expensive and a total nightmare...never buy them!

We purchased this high end Dacor range (Dacor Renaissance ER30G) new in 2011 from the Appliance Loft here in Cincinnati. It was dropped off and installed and would not operate right out of the box. A repair was made and everything worked (unless you count the indicator lights on the knobs, they all went out after approx 14 months). This past November the oven went dead. A1 appliance came out: Determined new control board needed, ordered and installed. Thanksgiving Day, oven dead. A1 comes back, reset the High Temp Fuse. Oven dead 4 days later, A1 returns with a new HTF. Dec 22, Oven dead. As soon as The holiday is over we will call another repair shop and start looking at replacing this unreliable piece of eye candy. Open comment to Dacors design engineers, quality control engineers and management. You should be totally ashamed about this product youve designed. You are supposed to represent the best in American design and quality and this falls below that of low end appliances out of China. See you in small claims court.

I have been very disappointed in the reliability of our Dacor refrigerator, model EF42BDCBSS, purchased in 2007. The first circuit board went out in 2008 within 6 months of the initial purchase. A replacement part could not be located. It was still under warranty so they replaced the whole unit. In 2010, we had to have another repair to regulate the temperature of the freezer. Last week (October 2012), the circuit board went out again! Even though the unit itself is less than five years old, it is no longer under warranty. Dacor goes by the original installation date. I contacted Dacor and spoke with LS who basically stated that all they could offer was a discount on the part. This repair is costing us over $650, not including the loss of food. We paid to have the part second day. When we called back the next day to get a tracking number for the shipment of the part, we were told by another representative that the part had not shipped because it was out of stock in the default warehouse. He was able to locate it in another warehouse and get it shipped the same day. I called LS back and she stated that she never promised when it would ship, but when it did, it would go second day. I would not expect this type of repair cost and attitude on a refrigerator that was over $9,000 when new. Now, I am concerned with the liability of our range and microwave, which are of the same Dacor brand. The main reason I took the time to write this email is to make retailers aware of the situation and ask that you seriously look at the reputation of the Dacor appliance line and decide if you really want to promote this product to your customers. Dacor could care less about their customers and/or reputation.

We have an 11 year old Dacor double oven with convection on top. The relay board malfunctioned and there are no parts to repair this. All Dacor would tell us is that they dont carry the parts anymore. Evidently, they are not required by law beyond about 8 years and that appears to be all they do. Our appliance repair person even contacted a company that rebuilds electronics and they cant get parts for this board. It is unbelievable considering what we paid for the oven. So we now have to replace it. Dacor offered us a discount on a new one. Not good enough. I cant imagine putting another Dacor product in. Two appliance service people have told me that Dacor has this reputation and they would not put them in their own houses.

My Dacor oven (DO130S, S/N V-A-10160044) is less than 18 months old. While it was in use, it popped, sparked, tripped the circuit breaker, and died. I called customer service, and voiced my concern on safety due to potential electrical defect. Steven, the customer service person advised me that this oven is no longer in warranty, and to call a repair service. I reiterated the concern for product safety. He placed me on hold, and the call was dropped. I called again, and Mike answered. I repeated the same info, and he was not willing to listen to any concerns. He hung up on me. This experience does reflect on published Dacors commitment to customer service, or product safety.

We have had problems with the igniter switch which clicks when I have a large pan or pot on the stove. My husband has tried cleaning the igniter tip with a brush as well as the removable ring but we still have that problem. We also have a Dacor microwave that seems to blow a door fuse pretty often that has to be replaced.

Got a great online deal on Dacor LP gas range. Was new but had dinged side panel according to store. Couldnt see the ding in photos and it would be hidden against cabinets anyway. Range is finally delivered and is new as advertised. Works great for a few days but then the oven wont hold temperature and then wont light. This is when the nightmare begins. Samsung now owns Dacor and getting to the right people to make a warranty claim is insanely difficult. After making the repair claim we get notified that there is no warranty coverage for service as this was not a new unit. Pardon me but we have the sales receipt showing that it is with full factory warranty. They finally agree to accommodate us and then repeatedly cancel repair tickets. After many calls to fix this, they now tell us that no service center will come to repair the range! They offered a refund minus some sort of discount based on a stove being used for a period of time. Oven stopped working a week into having it and they want to DISCOUNT a refund! Made BBB complaint and their response was they would have someone reach out to the customer. Today they did that and we are still at no resolution. Told them they have 3 options, fix the range, replace the range or refund us completely and I will make arrangements to fix the oven. They say there are no ranges in inventory to replace this one with with. No one inside the US will call or reach out to fix this fiasco and we are left with someone that is not allowed to make decisions that speaks english as a second language. Sad thing is that its a basic range that at first seemed to be a great design and would be great to have in our kitchen. Its now endless headaches because Dacor refuses to step up and remedy a defective oven part with a service call from someone that would require likely higher pay than their network providers.

I have all Dacor Appliances in my kitchen and I am very disappointed and angry. The double wall oven has not worked since day one - cant roast a chicken or God forbid, I would want to roast a turkey for Thanksgiving. The ovens look great, but just wont cook anything. Raw on one side and burnt on the other. One time I roasted a 5lbs leg of lamb for 5 hours! It still wasnt cooked. Recently, my dishwasher has stopped working properly, stops midway through cycle, wont drain water and its just been a total waste of money. I will never recommend Dacor to anyone. Do not buy Dacor. I called customer service in the beginning, as we had problems from day one, but they were of no help so I gave up. I dont use my ovens anymore, they are just for display. Very, very shameful!

Oh how I wish I never bought a Dacor! It has been nothing but problems. I figured I bought a lemon but after reading other reviews its just not a good product with not very good customer service either. I have had repairs every year, and even after repairs it still isnt functioning as it should. The first problem I had was the whole glass window blew out during baking, which seems to me is a huge liability. The company said that shouldnt happen but is out of warranty and would give me a discount on the glass. I thought that was better than nothing but then 6 months later the relay went out, then baking temps were all over the place in the oven so they said I needed a new motherboard and they said both ovens needed it. So those were repaired. Oh ya and the light in the bigger oven hasnt worked past the first year even after having the light changed and some electrical stuff done on it. Then I had the bulbs changed due to irregular oven temps. The temps are still all over the place to this day.The back right corner gets too dark. The front left doesnt brown and is a lower temp. Now Im having problems with the oven turning off during baking and when using broil in the small oven it causes the large ovens probe alarm to go on and offer at least for an hour. Dacor didnt help me with anything past the glass and its only been 7 months since the new motherboards were put in. I cant afford to buy a new oven at this time and so I only use the small oven mainly since the larger has so many problems. Do yourself a favor and never buy a Dacor!

Eight months ago I renovated my whole kitchen with all Dacor appliances, cooktop double wall oven, refrigerator and dishwasher and I could not be more pleased. I wanted to wait a few months before I wrote this review in order to make my review more accurate. I love the modern design of all the appliances. The refrigerator is nice and roomy and the cooktop has been very reliable. Dacor products cost a bit more but they are well worth the extra money!

In September 2009 we did a complete remodel of our kitchen. Replaced everything but the refrigerator, with DACOR appliances. Within a few months we had problems with the dishwasher and finally replaced it with a GE in 2012. About that same time we had problems with the Dacor Epicure 30 Single Oven Model EO130SCH control panel and had to have the repairman out to work on the relay/computer board. At Christmas 2015 I had trouble baking, the temperature wasnt accurate and have had the repairman again. He says that the computer board is fried (his term). Ive tried calling Customer Service with no success. Ive e-mailed them with same results. The appliance repairman has told me that he cant find the part. All the distributors that hes called have been told that the part is on back order. Ive been without an oven for over two months now with no fix in sight. Have been told that IF we find the part it will probably run around $500.00. These are appliances that are only six years old and have had gentle use by senior citizens. Anyone reading this - PLEASE DONT BUY DACOR! Youll be sorry as I am.

I bought a 30 Dacor Double Oven (EO230SCH), 36 cooktop, warming drawer and matching convection microwave. Well over $10k. The microwave has been replaced as it died early within the first year while cooking popcorn - nearly started a fire in the kitchen... However the cooktop igniter died at 4 years and now the wall oven is on its third control board in years 3, 4 and 5. Nothing is under warranty and they want nothing to do with me now. The replacement oven controls cost ~$400 each plus installation. So after all this expense, I have invested $1,200 more in replacement parts and the cooktop needs an aim & flame to light. Total crap. Im going to replace all of this and will never go back to Dacor. I took the time to write this so that others will not waste their time with what I have to assume is the worst quality in the industry. Please dont waste your money.

I did a kitchen remodel in 2008 and was convinced by the sales guy at Home Expo to go w/ the Dacor over the Wolf. I bought the dual-fuel 36... Within 2 years I had serious problems. The oven, when not on Convection Roast or Con Bake, just using Bake will consistently turn itself off... Ive ruined many a meals, usually big ones: Turkey, Prime Rib(long cook time items). This was by far my most expensive investment in my kitchen and by far my biggest disappointment. I have called Dacor in the past and was told they could refer me local repair people, I was on my own for fixing it. Again, huge disappointment.

We bought a new house a couple years ago, and the kitchen came with a suite of new Dacor appliances - range, fridge, and dishwasher. They are all terrible.The led indicator on the dishwasher is scrambled. The icemaker in the fridge clogs up into a solid block of ice. We had this fixed, which involved a new control board and some caulking, but the problem returned not long after. The knobs on the range feel like theyll snap off any time. The lights in the oven arent seated properly and they interfere with the oven racks. It takes forever to get up to temperature. And Im starting to think I have a gas leak. How can these products be so expensive and such utter garbage? Oh, but they have wifi!

When my husband and I built our home 11 years ago, I splurged and got a Dacor ERD36 36 dual fuel range. During the process of our build, our builder dropped my range during the installation. Dacor was very quick to send out a servicer to make sure the performance of the range was not compromised. The only thing that needed to be replaced was a bent bullnose in the front and the kickplate. I have had one service call in 11 years, which was last year after a brownout in my neighborhood caused my clock and oven setting to go crazy. It had nothing to do with function and had nothing to do with shoddy manufacturing. I just got it fixed and continue to use my range every day. I am looking to expand my island because I need another oven and I am very excited to add a Dacor oven to my home with zero hesitation. I am looking at a DO130S. I would buy Dacor over and over again!

I built my home in 2003 and installed a Dacor 30 wall oven. After several years of poor performance, we started to get an error message. Dacor suggested replacing a board for $300. That didnt work so they had me replace another $300 board. That didnt work so they told me I needed a new front panel and it would run about $1,000. That board is on back order and they dont have a replacement date. Thinking that its bad business to sink $1600 into a troubled product that has terrible reviews on the internet. We found out that once you go with Dacor, you need to stay with Dacor due to an unusual, nonstandard size.Thinking that Dacor has improved their product we ordered a brand new $3,000 Dacor RO130 30 wall oven. It arrived promptly and I removed the defective $3,000 oven and put in the brand new $3,000 Dacor RO130 oven. What I got was a dead brick. The Dacor customer service has been awful, and will not allow me to talk to anyone in their technical side. The oven is getting power. Dacor customer service wouldnt help me unless I could prove that the unit was getting power. So I had to get an electrician in to prove that I had properly wired the 4 cords that came off the original defective Dacor wall oven. Get service help? No chance. I live 100 miles from Seattle and no one wants to work on Dacor. So here I sit with a $3,000 brick. No service and Dacor has no clue on how they will service this wonderful $3,000 RO130 30 wall oven that is an out of box failure. I dont see how a company that has this bad of a product, two generations of defective ovens, bad customer service, reluctance from the repair community to work on their products will be in business much longer. If you are considering Dacor appliances, consider the problems that I am having. The nonstandard size of their ovens will lock you into future purchases to replace their products that dont last 10 years.

Purchased home with installed Dacor double oven. Oven wouldnt reach set temperature, so replaced control board. Doable, but a real hassle to remove oven from wall opening and label, disconnect, and reconnect 20-something wires. Two years later, the clock cannot take the correct time and oven timers do not work. Only fix: replacing the $300 control board again. I cannot recommend that anyone purchase these appliances as the control boards simply do not work for more than a couple of years.

We did a major remodel in 2006 and were talked into Dacor Appliances by the kitchen planner. Big Mistake! The first time we tried to do the wall oven self-cleaning, the circuit board blew out. Since it was just past warranty and no one near us in West Virginia would work on it, I found a board online for $200.00 and replaced it. It has never heated evenly and now it wont heat past 350 F and maintain temp. The Dacor range hood sounds like a jet plane and the variable speed switch wont reduce rate. The bulbs burned out and after buying two online for $30 each, I removed the decorative housing and use a more standard $10 bulb. The Dacor gas cooktop is OK except that EVERY time you turn on a burner, one or two of other igniters start clicking and wont stop until you find which one it is (not always the same) and turn it on and off. Please heed this and all the other warnings from the choir. DO NOT BUY DACOR! It is all very expensive junk! I only gave it 1 star because there was no way to rate Dacor a zero!

One year ago I completely changed out all appliances in my kitchen. My favorite of the four appliances is the range. We have enjoyed all kinds of new cooking techniques. As my wife put it, I did not realize how crappy my previous range was. Gourmet cooking is what Dacor is founded on and we could not be happier with the performance. Our favorite feature on the refrigerator is the in door water pitcher. Fresh cook water that can be taken to the table and refilled upon placing it back in the refrigerator. And the combi-microwave is an incredible second oven. All products have performed as advertised and promoted, and with a three year warranty whats not to love? Thanks Dacor for making amazing beautiful appliances.

I wish we had seen these reviews before we spent 6k on an oven and cooktop. Ordered cooktop and oven in November. Custom color over to match cabinets, still have not received oven (were at the 8 week maximum wait time already). Cooktop appeared fine when we received, but when we went to install, noticed something rattling inside. Looking through vent, noticed several broken interior pieces moving around. Contacted Dacor 3 weeks ago for a replacement or repair, and still nothing. They made us go through dealer, and last week told dealer we refused service. Ridiculous! Now they are telling dealer they cant find a servicer nearby. Am considering declining payment through credit card company for their lack of follow through and service, and let them come get their unit.

We purchased the modernist collections 48” range, refrigerator and freezer, oven and microwave combo and dishwasher with a kitchen remodel 9 months ago. We had one issue with the dishwasher which was resolved, then another when is stopped mid-cycle. Repairman came out and was told we needed a new panel. Found out it was back-ordered. Well, it’s now been FOUR month without a dishwasher. We have contacted customer service and asked for other options and were told there was nothing they could do! When following up we have left messages and had our calls not returned, as has our service company. I have waited on the phone 3 times 30 minutes to talk to someone, because they won’t call back. We’ve asked to talk to a supervisor, and was told our information would be forwarded... 2 days later, no call. This is by far the WORST service I have ever had for ANY type of product.

The ovens needs a new latch kit and a mew control panel every year. It has been repaired 15 times. So many issues but those are the most consistent problem areas. Dacor should have replaced our range the first year. Even the repairman says everyone has had the same issues. For what I have paid in repairs I could have bought a new range.

I purchased entire kitchen of Dacor appliances - $30,000. The 48 refrigerator required 9 service calls to stop freeze up. Wall oven – the digital panel went bad. Stove top exhaust – the circuit is melting. The dishwasher had 17 service calls over 2 years - mid way they replaced the unit because they could not stop it from leaking and damaging our wood floors. The most recent service call was yesterday, 12/20/2011. After waiting since November, it is again not working. Does anyone else understand that spending $1700 on a dishwasher should allow you to use the dishwasher? I called the customer service and was told We are discussing the situation and will get back to you. Are you going to come wash dishes with me over Christmas when we have 25 guests? Were you there on Thanksgiving? If I hadnt been stupid enough to buy all Dacor appliances, I would throw it in the dumpster and buy a GE from Home Depot.

My oven would not work. Neither the broiler nor oven element would heat. The dealer from whom we purchased the range had gone out of business. So, I wrote to customer service on the Dacor site. Dacor customer service was back to me within 24 hours with a suggestion on what might be wrong. My husband followed the easy directions and my oven is now working! I am very happy with the prompt reply from Dacor customer service. They even provided a dedicated phone number if we had problems.

The Dacor (model ER36SCH/NG) burners work, but the oven & the broiler burners will not. The circuit boards were replaced twice 2 times, under warranty, but still fail. I have to un-plug, or turn off then on the breaker to reset the circuit board. Dacor states that they are aware of defective boards, but are working on new replacement boards (no board yet). Its going on now, for over 6 months. Is there any news? I am very frustrated!

We renovated our kitchen and as part of this had installed the new Dacor Modernist Fridge and Freezer columns at a VERY hefty price tag. We were going to get a subzero and changed our minds when we saw these products - the styling, design and function looked so much better than Sub-Zero, despite the higher price tag. Well, fast forward about 8 months and we dont have a functioning fridge. It stopped cooling out of nowhere. We had to throw everything away. After FINALLY getting a repair person to the house, they told me that it was because the fridge had run out of gas (freon or whatever the coolant is thats used). When asked how that happened they said they didnt know, but that they couldnt repair it as they needed a part from Dacor. A WEEK later, they finally got the part and came back to repair the fridge. 4-5 hours later it still was not repaired and they said they needed another part. Its been almost two weeks since then and the part has still not arrived. We had a BlueStar range installed when redoing the kitchen and when we had a problem with that, they overnighted the part, so that they could fix it right away. This is not the case here - the customer service has been absolutely horrendous and Ferguson Appliances (where I bought the fridge from) has been at their wits end with this (I cant say enough about how wonderful Ferguson has been to deal with). This has been a nightmare. Now the repair place wont even schedule a repair date because they dont want to lose the time again in case the part doesnt show up again... DO NOT BUY THIS FRIDGE. I should have known better not to buy a Samsung (yes, Samsung bought Dacor a few years ago and these products are glorified Samsung units).

We bought our new Dacor CPS 130S wall oven when we built a new house in 04. First we had to replace the lower heating element. Now the touchpad (Dacor part # 13290S) is malfunctioning. The + button will not respond to touch. Called Dacor and was told that the needed part number was discontinued in 2009. I double-checked with a distribution center in San Antonio, TX, who confirmed that the part is no longer available. They referred me back to Dacor on the chance that Dacor would have one somewhere. Dacors suggested solution was that we need to buy an updated completely new oven, which would cost us several more thousand dollars. So here we sit with a perfectly good oven minus a touchpad to control it correctly. So much for buying reliable, U.S. made products and receiving good service. I thought there existed a federal law that mandates a company must make parts available for 10 years if they discontinue the product?

When we recently remodeled our kitchen, we replaced our Dacor double ovens that we had had for 15 years. These were great ovens and not one problem with fairly heavy use, so we bought the Dacor Modernist double ovens. The ovens are usable, but they are the worst engineered product I have ever experienced. First, there is no clock on the stove because as I was told the clock would etch the screen if it was on 24 hours a day. Second, the sound the timer makes is so soft, even on the loudest setting, cannot be heard in any room but the kitchen, so I paid a premium price to carry a timer with me, so I know when my oven is done baking. Third, if I turn the oven light on, the timer either stops completely, or it resets to the original time. Fourth, the oven buzzes when it is cooking. Fifth the user manual is useless and there is no video or online information on how to use this oven that is not user friendly.Finally, I have talked to Dacor and have had the repair person here, but he knew nothing about this oven. I am sorry every time that I use this oven that I did not buy my other choice, which was the Woof double ovens, but we thought this would be wonderful product, like the wonderful product that our previous ovens were. We also thought Dacor was a family company, but is now owned by Samsung. What a disappoint these ovens have been. The engineering for this product is a disgrace for any company and I no longer see the Modernist products advertised and it may be because it is such a poorly designed product. I never met a computer that I did not love, but this is not the electronic wonder that was advertised when we bought the ovens.

I am thrilled with this stove. I have always had a vertical double oven so this is a first for me. Really pretty in my kitchen. Almost like a piece of furniture. Can’t wait to start cooking!!

We have enjoyed our Dacor oven for a number of years but cannot recommend this brand due to high cost and frequency of repairs. The relay board, at $400 a pop parts cost only, has had to be replaced twice within 5 years. The oven door hinges failed in normal use so that the door would not close tightly and had to be replaced. The halogen oven lights fail frequently requiring replacement. Parts cost is only part of the issue. The inconvenience of not being able to use the oven for extended periods of time and high appliance repair labor costs are significant. All in all, a very good oven but reliability and frequency of expensive repairs lead us to not recommend Dacor ovens.

Dacor Fuel Range broken door - My Dacor is by now 13 years old. I see from other reviews that the problems I have with my range have not been addressed in newer models--the same problems exist. When I received my Dacor, there was a crack in the front, above the door. It was small, and Id just had a baby so I let it go. I noticed that the door did not close either, and because I did not address it within a year, Im out of luck. But youd think that making an oven with a door that closes snug would be a top priority. It only closes properly when in cleaning mode. My oven window became brown and I cannot clean it. Its a shame that these things are messed up because the convection seems to work wonderful and the oven is fairly attractive. If the door closed all the way. Im getting ready to consider a new oven. Wont be a Dacor.

We remodeled our kitchen in the fall of 2009 and decided to purchase what we thought were higher end Dacor appliances (stove top, oven and microwave). Well, what a mistake that turned out to be. Considering the price we paid for the appliances, you would not expect problems from all 3. Perhaps a problem with 1 appliance, but problems with all 3 suggest a real quality problem. My first indication should have been when I called and asked how to change the green LED on the microwave to blue to match the nice blue LEDs on the oven mounted right below. I was told that someone else makes the microwave and Dacor just puts their name, and that I should just turn off the LED on the microwave. I dont know if that is true, but that is what I was told.Now when using the microwave/convection feature, the oven makes a noise (sounds like a fan motor) for the first 3-5 minutes then eventually quiets down. A daily reminder of the mistake we made purchasing Dacor. Then those nice blue LEDs on the oven started failing making it impossible to read the clock, timer or temp. Luckily, the oven still works; you just cannot read the LED any longer. This is a constant reminder of the mistake we made buying Dacor as we see the LED every time we walk into the kitchen.Finally, we have the solid surface electric cooktop. Although it works fine, the black paint on the metal trim around the stove top is wearing off. Now, we have some shiny metal and some black trim. This is just an annoyance and honestly, we probably would not have even complained about it. However, with the other problems we have had with Dacor, it just adds to our overall disappointment with Dacor. If I knew then what I know now, I would be a lot happier because I would have GE appliances and not these overpriced low quality Dacor appliances.

I called the customer service number regarding my double oven. It just randomly beeps and now turns off. No error code displayed. It has done this on and off since 2003. Now it is happening all the time. I called customer service and they seemed to act like it is my fault and I need a new touch pad. I inquired and this is a recurring problem with this model. I could not get a straight answer from the person I was talking to. He just told me that if the repairman says I need a new touch pad, then I need to get one. Well I have been doing some research and this is a problem that seems to be haunting more people than I. We own a Dacor gas cooktop that has had to have a switch repaired. We own a microwave that has had two new circuit boards and now a beeping oven that gives no error code and turns off by itself. My advice, do not buy Dacor appliances.

We bought 3 very expensive Dacor appliances when we built our home 12 years ago. They have been a total disappointment. The microwave was replaced after just a couple of years when it just stopped working properly - including needing to stop it by opening the door! The wall ovens have needed many minor repairs which have amounted to several hundred dollars after labor charges. I see on this post others have had to repair the hinges! Ours have been replaced twice! The broiler came loose and was hanging on one side. The internal light also goes on and off by itself - sometimes in quick succession. At times, it stays on and cannot be turned off by the light button but by banging the front of the oven! Ridiculous! The cooktop cooks very unevenly. It goes from simmer to boiling over. The ceramic material did not hold up very well either. It is supposed to clean easy. But there are spills that have left permanent stains and we will be replacing that as well. We have also had Customer Service tell us items have been discontinued so we have no choice but to replace these appliances since replacement parts cannot be purchased any longer. This is a warning to anyone considering Dacor - DONT WASTE YOUR MONEY! There are far better appliances out there!

We purchased a Dacor Double Wall Oven in late November of 2019. I liked the oven and it functioned well until October of 2020 when the oven quit working due to a control panel issue. We were told the part was on back order. I continued to check with Dacor customer service and was continually told the same thing -- it was on back order. Never once did they call me to give me an update.In December of 2020 when I called I was told there was an update. The part was no longer on back order it was no longer in production, they no longer make the part. They would review the file to see if they were going to give me credit for the oven or get me a new oven. I contacted them again today and was told it was still under review and it could take them another couple of weeks to decide what to do. I asked to speak with a supervisor but was told that there was not one available. The person I spoke with today said that she would call me next week to give me an update. I appreciate her concern but that does not get me closer to a working oven. I would not recommend Dacor to anyone, customer service is terrible.

Dacor Epicure Dual Fuel Range and Microwave - Where to begin? Perhaps at the end is best. Dacor appliances are shoddy, unreliable, outrageously expensive to repair and there is no customer support. That about covers it. We bought the above noted pair during our kitchen renovations 8 years ago. We thought that Dacor was a premium brand that would give us long trouble free service. How wrong we were! The only thing Premium about them is the price. 4 years ago, the microwave door refused to latch. Thanks to YouTube, I found out how to remove the door backing and found that the plastic part that comprised the latch was broken. Dacor was contacted - they no longer had the part. Try the open market I was told. I managed to jury rig a repair by using a wooden shim. 3 years ago, the range packed it in. Another repair - this time I was told it was the circuit board that had failed and which was replaced to the tune of $700 and I was cautioned that the second circuit board was not working very well - the interior light would not illuminate and the blue lights indicating a lit burner didnt work, and I should change it too. The smaller circuit board was costed out at $400. Last week, the door latch motor failed and the range began to beep incessantly. Now the oven cannot be used and repair costs quoted over the phone were in the 1000$ range. Thats it for us. Dacor is junk and belongs where its headed - the junkyard. Dont buy Dacor. Live and learn I guess.

I bought DCM24S DACOR 1.5 CU CONVECTION MICROWAVE-SS and after few months of using this product its banded on the back wall of the microwave that supposedly resulted from improper turntable placement which caused the turntable tray to make contact with the back of the oven. The quality of the product is very poorly, dont buy Dacor product!

Two years ago, we redid our total kitchen at considerable expense. All of the appliances we replaced were made by Dacor. They included: 1) a 36-inch refrigerator model EF 36/wf; 2) a dual wall oven, model EO230SCH; 3) a gas cook top, Model RGC304; 4) a dishwasher, ModelEDWH24S and; 5) a range hood, ModelEH3012SCH. The problems started within a two months of installation. The refrigerator stopped running due to a relay failure and a compressor problem; both were replaced by Dacor at no cost to us. It was inconvenient but not costly. A short time later, the lower wall oven stopped working as well as the lights in both ovens. This required the replacement of the main control panel (control circuit board). Dacor paid to have it repaired. The clock does not keep accurate time and gains about an hour a day. We decided to leave it well enough alone and did not have it fixed. After the one-year warranty expired, the lower oven quit again. This time, it had to be removed from the wall and an exhaust fan in the lower oven was defective and had to be replaced. Dacor’s initial response was it was out of warranty, so it was up to me to cover repairs. They eventually agreed to supply the part (about $90) but we had to spend several hundred dollars to install. Now, the lower oven takes an extremely long time to heat up, and again we decided to leave it well enough alone. Recently, there was a loud flash in the vent hood; one of the bulbs apparently burned out. My wife tried to turn off the lights in the hood but the light switch apparently blew when the light went and could not turn them off. After a couple of burned fingers and a melted bulb removal tool, I managed to get the other bulb out. A call to Dacor got the usual out of warranty response. I called the local Dacor authorized service rep. He looked at the problem ($95) and said he would have to call Dacor. After he talked to Dacor, they called me and said they would send a replacement control board but would not pay for the service calls. The service company said the next service call would be $195. One light bulb burned out: cost $290. I suspect that every hood unit that Dacor made with this control board is also defective. We have had to replace the halogen bulbs with great regularity. We have halogen bulbs in our boat that have lasted at least 15 years. There was another complaint on this board that had a similar problem with the vent hood. He decided to fix it himself. He is an Electrical Engineer his comments are worth reading and speak to the inadequate design of this unit. It is a shame that the Dacor appliances appear to be near the bottom in terms of reliability. Consumer Reports that their gas cook tops appear to be the least reliable. It looks like I have something to look forward to. Needless to say, I cannot recommend Dacor to anyone. In fact, I would recommend that they not purchase any Dacor product that does not have a full multi-year warranty.

I purchase a home with a Dacor double oven. Unfortunately the oven begins transmitting multiple beeps and the touch panel will sometimes read off after beeping a while. I contacted the staff at Dacor requesting a service manual. They refused to send me a service manual and stated that only authorized technicians can service their equipment. Its obvious they used google or a local phone book and sent me contacts of appliance repair shops in my area.When I called, they had never heard of Dacor let alone be factory authorized. I called Appliance repair shops up to 50 miles away to find there were no Dacor Dealers. I found one 70 miles away but it was too far to send a technician. If I remove my oven from the wall and take it there they would attempt to look at it. I had to reverse engineer the thing to find that my touch panel has gone bad and now I cannot find a used one. I want to recommend that anyone considering an appliance DO NOT PURCHASE A DACOR! If you are looking for high end stick to SubZero / Wolf. Oddly enough I see that there hasnt been any reviews for the past 5 years. Maybe it appears people have stopped buying Dacor appliances.

As an add-on to my original review, I had a a service call to address the LC error code. The service company reconnected my unit, turned it on, ran a couple tests, and declared there was no issue. We ran the dishwasher 1 cycle and it worked just fine. Tried to run it again later that day, and the LC code was back again. To resolve the issue, I worked with the company I bought my appliances through to replace the Dacor dishwasher with a Bosch. That happened today, so it is too early to tell say how the Bosch works, but it is more solidly built, has more capacity and the door fully opens with the panel installed.Dacor did reach out to me to try to resolve this issue, so kudos to their customer support, but the issues were just too many. And as I stated in my original review, love the Dacor range top, double oven and refrigerator.

DONT recommend model #MOH130. We were so impressed with the options that this oven came with. Sadly, with all the bells and whistles also came a ton of repairs. After the 4th repair, our service rep said the relay board needed to be switched out. (Half of the service men who came to my house seemed to be grasping at straws trying to come up with an explanation why the temperature was fluctuating, or why it took so long to heat up, etc.) Then I get to wait 2 weeks for a part to be ordered/arrived and re-schedule service. Last week got code U22 - oven wont even turn on. This oven is only 6 years old. NO THANKS - NEVER AGAIN will I buy anything from this company.

Ive had the 27 inch double wall oven for 10 yrs. When I purchased them they were 6000 dollars. With 3 years I started having a problem with the motherboard. It has been replaced 3 or 4 times. Ive lost count. The last time they said it was fixed for sure. Well today the same issue is occurring. Im done! Never buying another Dacor product again.

We remodeled our kitchen less than 5 years ago. As we have owned restaurants in the past, we wanted commercial quality appliances. I was looking at Sub-Zero and Viking or Wolf. Unfortunately I took my Home Center convince me to purchase A Dacor package. That was a mistake. Even though these appliances cost as much as the those brands, the quality is not even close. After spending $22,000 on appliances I have quickly discovered that these appliances are junk. First the microwave began to arc and nearly caught fire. Even when they installed my cooktop. I noticed that the burners in the middle were marked incorrectly and the blue LED indicating the burners are on was burnt out.After only a few years, now my ovens are not working. And right before Thanksgiving I am without ovens. My old ovens were almost 50 years old and worked fine. These $6000 plus ovens are not even 5 years old and are down. I am kicking myself for not going with my original plan. If you are considering Dacor, I would not recommend.

Most of my life, Ive always bought pretty low end appliances, and theyve always worked pretty well. When we remodelled our kitchen, we decided to go with a high end Dacor stove, and its been nothing but trouble. After just a few weeks, the igniters started to fire constantly on some burners. It was still under warranty, but it was very hard to find someone to honor the warranty. We got that fixed, then the oven light started to come on and off randomly. After our experience with the first problem, we just disconnected the light and let it go. A few months later, the bottom shelf jammed, and there was no way to collapse it to fit in the oven. This product is total junk. Dont buy it!

Years ago I purchased the Dacor Double Oven over a Thermador because the Thermador had a ridiculously long pre-heat time. The Dacor has performed reasonably well as a oven particularly in convection-bake mode. But over time, components started failing and repair parts were hard to find, unavailable or ridiculously overpriced. I am an an engineer with DIY skills honed from years working with high tech food manufacturing equipment and controls including ovens. In recent years, I have needed to replace a relay board, the main control board, hinges two times, and most recently the hinge receptacles. I have also replaced an inner panel on a door assembly. Just think what such repairs would have cost for an average consumer. I understand the parts can fail, but Dacor has shown little regard for consumers in my opinion. They have done very little to maintain an inventory of repair parts. Basically their message is that the part is now obsolete and unavailable. Thats some answer when the price of a new double oven is multiple thousands. Recently, the hinges on my upper oven failed again. As they failed, their failure caused increased wear on the hinge receptacles. Soon the receptacles failed as well. I was able to find hinges at a ridiculously high price but the receptacles were unavailable anywhere. I contacted a several parts suppliers who told me that they had no idea when the parts would be available. Moreover at least two of the suppliers mentioned that they had a backlog of orders for the receptacles - one had a backlog of over thirty. Yikes!. At that point I contacted Dacor customer service and asked what could I do to get the part. Answer: The part is unavailable and we have no estimate on when it will be available. I tried to escalate my request and got nowhere. Finally after many hours of online searching, I found one set of the hinge receptacles at a price 4X last years price. Lastly as I replaced the receptacles today, I realized that the mounting screws only hold one portion of the U shaped mount. If the screws were longer, the receptacle would be less prone to twisting and wear. Be aware that Dacor was sold to Samsung a few years back. Based on my experience, I could never recommend Dacor. Caveat Emptor!

I purchased my Dacor Epicure Range 8 years ago when I remodeled my kitchen. My other appliances were made by GE and Bosch. Ive had to service my GE appliances a couple of times in the last 8 years, but it is the Dacor that has given me the most grief and it was the most expensive appliance purchased. It has never been reliable with regard to convection baking. Initially I thought it was my inexperience with a convection oven. I read everything I could get my hands on and kept trying...after talking with a friend who does quite a bit of baking I realized its not me, its my oven. Then the real problems started. First it was the broiler/ignitor, next it was the membrane in the keypad. Two months later it was the relay board and this time it was the broiler/ignitor....Again! Started calling Dacor when the relay board went out because at this point I had spent $1,000 on repairs....after I had paid $4,000 for the range itself. For the last two repairs Dacor has paid for the parts, while I paid for the service call and labor. This has reduced the cost of my last two repairs by about 50%, which is very helpful. However, Im still very disappointed in the product. I spend a good deal of time in my kitchen and do quite a bit of baking, cooking, and canning. I thought that if I spent more money and bought a high-end appliance, it would serve me well. At the rate that Im going, I will need to purchase another range, unless I want to keep throwing money into repairs on this one, which I dont. I will not ever purchase (or recommend) another Dacor product again.

I purchased this upgrade to my kitchen renovation. The stainless steel stove has a great look, but that is all it has. This is my third repair (with much difficulty). The same problem - the bake ignitor goes bad and sends gas smells throughout the kitchen. On Christmas day, after preheating the oven, I opened the oven door and the inside was one large flame. The heat was intense and my right arm got hot from the heat. I immediately closed the oven and cancelled the bake setting. When I called Dacor the following morning, I thought I was talking with a robot. No emotions, no sense of caring. They must be programmed. I got no satisfaction. I said, Do you understand? My stove went on fire and on Christmas day. My family was not sure if they should leave my house. I am extremely disappointed with Dacor.

We used a new Dacor range vent only to have it go on and off. We called Dacor and they referred us to Desert Tech in La Quinta. The owner came out and said we needed a new unit for $775. We said just unplug it. He charged us $275 even though it took him less than 30 minutes. Stay away from Dacor AND Desert Tech!

I bought this beautiful range and choose Dacor but when we used the Green Clean on it the enamel pealed off a spot on the bottom of the oven a 2x4 inch patch. Now Dacor say that this is cosmetic and will not honor their warranty. I have been calling them daily because they do not call me. Their service sucks.

We purchased a Dacor gas range in 2005 for $2000. In a short time the plastic trim around the knobs cracked, and the glass in the oven door had not maintained its seal. I contacted Dacor several times and was told to take a picture and send it to them, then they could decide a course of action. The course of action was that I would pay for materials and labor. I decided not to do that, and eventually I will replace the range with another brand, never a Dacor!

Do not buy a Dacor appliance unless youre okay with replacing parts for the oven in less than 2 years. The control electronic part was replace then less than a year later the user interface had to be replaced. Less than a year after the user interface was replaced, the oven completely stopped working. After calling the same repair guy to come fix it, they informed me that the company no longer sells the control interface. When I called the company, the only options they gave me were to send the part to a third party refurbish company and have them fix it. That means I would have to call the service repair company for the FOURTH time to have them remove the part, I would need to send it away to get fixed and call them back to put it back in. Dacor didnt even offer to pay for any of this. The customer service rep offered to give me a discount on a new unit. Are you kidding me?!? Please do yourself a favor and dont buy anything from this company. They dont back up their products and its clear they dont care about their reputation. Its a waste of money to be spend on high end appliances that are poorly made. Spend less from a different company thats been around for a long time. At least if a part goes, youll have reassurance they will have that part handy. A terrible company. I hope they go belly up soon so they can stop selling overly priced kitchen appliances to people.

Dacor customer service contacted me and worked with me and the appliance repair company to get the proper parts to fix the oven. Everything is fine! We once again really love our Dacor wall oven.

As a contractor, we were fortunate enough to build our dream home which was completed in 2005. After much research and many show room visits, we purchased Dacor appliances for our kitchen. As the saying goes, if I knew then what I know now. Our biggest (note I said biggest, not only) issue is with our ESC130 oven. If you own this oven, do not, repeat, do not, use the self-cleaning mechanism. I have had this repaired once and then replaced once (along with a relay board). I seldom use this because I know when I do the lock mechanism will continue to cycle until it is replaced. This means, while I can still use my oven, I have to time when I open the door based on when the lock is cycling in the unlock position. I must also turn the oven off at the circuit breaker or listen to the continuous warning beep that the lock is cycling (as if I didnt know).After repairing this feature once, I next choose to have the mechanism replaced and Dacor offered me a discount on the parts (the oven was and still is out of warranty) at a cost of more than $500.00. This is on top of what I had already paid to have it repaired just 18 months earlier. I feared using this feature again as I didnt want a repeat performance. After cooking macaroni and cheese yesterday, I felt I really needed to clean the oven and made the mistake of using the self-cleaning feature of the oven. I dont know why I was surprised when the locking mechanism refused to stop cycling.I contacted Dacor today only to speak with the rudest customer service representative I have ever encountered, Steven. No last name. He is the only Steven who works there. He refused to listen to me, spoke over me when I did try to talk, and did not allow me to speak with anyone else. There are no supervisors available on Fridays and he could not transfer me anywhere. I left a message for someone else to call me (they did not). I called back later that afternoon and was given the name of a supervisor, Nhi. She was not available and I spoke with another customer service representative. I learned that Dacor is aware they have a problem with this locking mechanism and are trying to correct it. This got my hopes up, thinking that the company would now do the right thing and replace this mechanism at not cost to me, or at least at no cost for the parts. Not so. Even though Dacor knows there is an issue with this mechanism and they are supposedly trying to correct it, all they can offer me is a discount on parts. Really? Wow! A discount for a part that you know doesnt work properly and probably wont work properly because they are still working on the problem? I just really dont know what to say. Is this supposed to make me happy as a customer? Would prospective customers want to buy a Dacor product knowing that Dacor is more than happy to sell me a known defective product at a discounted price and they should expect the same? It is probably needless to say that I would urge all prospective Dacor owners to not waste their money on any Dacor product as they do not care about their customers. I will certainly be doing my part to warn others and hope this serves to warn others as well. Dacor has a lot to learn in terms of building even what could be called a good product and standing behind what they sell as well as becoming a customer service oriented company.

We purchased a Dacor Epicure dual fuel range when we built our house 7 years ago. It was the most expensive appliance we bought and we wish we hadnt. We have had no problems with the stove top, but the oven, specifically the broiler unit has been a consistent problem. We rarely use the broiler and use the oven perhaps 2 or 3 times a month. Yet, the igniter had to be replaced in March of 2008 and again, in June of 2010. In January of 2011, the broil gas valve was changed and now in September, the broiler is again not working. I cant see pouring any more money into this appliance and will sell as soon as I find a buyer willing to take a chance on it. We have been greatly disappointed in this product.

This range was installed in January 2003. The door on the larger oven was replaced soon after because it would not close tightly and still doesnt with the new door. I have always thought that the oven temperature is lower than it should be but have been told twice that it is accurate, tell that to the turkey. The heating element on the large oven was replaced 2 years ago. Four of the burners dont light and have to be lit manually, this has been going on for 10 years. The relay board has burned out and now has to be replaced, $800.00 fix. The technician just left and could not replace it, he couldnt access the tight spot that it was in and wanted to cut the barrier panel to get access to it. He decided not to do the job and told me to call Dacor to get another repair service, which I just did. I was prompted to write this after reading other reviews and remarks. I hope this helps someone out there to buy a different brand.

We bought our Dacor 30” gas range in September of last year. We were tired of cheap stoves that lasted 5 years before they needed to be relegated to a landfill. We thought it was an investment that would provide us with a reliable appliance and worst case scenario, better warranty repair service than Home Depot or other big box store.After 15 months, the igniter for the oven stopped working. We tried the 800 number on the warranty registration website and no one there could bring up our registration, even though I could see it on the website. They gave me an email address to contact the people who could look it up and I heard nothing for two days. I called the 800 number again and they transferred me to another number and they finally found our warranty registration and issued a ticket for the repair.The company they use for warranty work in Toronto, is Home Appliance Repair GTA and they are absolutely horrible. They said they ordered the part on November 27, but they did not actually order it until December 6th. Dacor then sent the wrong part! I demanded that they send the proper part overnight and on December 13th they called and left a voicemail saying that the part would be here by today at the latest.It did not arrive and this evening I emailed them again and their response was that the part would be here on December 19th. How does it take a week in this day and age to deliver anything? I don’t believe that I will even have a functional oven for Christmas this year. I have already given up on any baking getting done. I will never buy a Dacor product again. I actually really love my stove, but I am beyond disappointed with their warranty service and customer care.

I purchased my 30 range and was so excited! Well no longer. First the wrong range was delivered. I had to wait another three weeks for the correct one. My oven can not cook at all. Temp fluctuates by 100 degrees. Going on my third service call and still not working. It very unfair, I have to take time off work to wait for repair person, then nothing is fixed. I wish I could return this lemon. But after reading other reviews I am not alone. Why is this company not accountable for ripping hard working people off. I love cooking. Its my passion. My Kenmore Elite was half the price and far more superior.

About 3 years ago, I spent almost $5,000 on a Dacor double oven. We had it less than 3 months when the motherboard had to be replaced. About 3 months ago, I started to get various error codes and a continuous beeping. An authorized Dacor service repairman has replaced the motherboard three times. He was on the phone each time with Dacor, however we still get the error codes and Dacor has told the service repairman that they are stumped and dont know how to fix it.Here I am, having a beautiful expensive oven to look at but was unable to cook a turkey for my family yesterday! It seems that there is a major error in this oven, and I am stuck with a huge repair bill and an oven that does not work. I can only hope that Dacor will step up to the plate and come up with a solution or replace the oven which obviously is a lemon.

I have a Dacor MORS130SS oven that I purchased in July of 2008. After 6 months the first membrane panel failed, one year later the second membrane failed. One year later the third membrane failed. Im on the fourth membrane and now my fine Dacor is burning things!! I can set the temp to 350 and it shows 350 on the display but the lower element never shuts off and whatever I cook gets burned. I bought this oven thinking it might be my last considering the supposed quality of Dacor. I know for sure it wont be my last oven!! I sell appliances and I never recommend Dacor ovens because of all the continued problems. Ive never used the self clean feature since being told by a Dacor tech trainer that he didnt recommend using self clean because it would cause the oven to age faster. Wonder how long it would have lasted if I did use self clean? Sure wish Dacor would contact me for a testimonial!

Less than two years ago, we purchased a Dacor classic wall oven from a local high end appliance store in Durham, NC. Within a few months, the electronics started getting glitchy; the oven started beeping in the middle of the night. I turned off the beep, but other problems started popping up. I baked a pie which was half raw on one side and overcooked on the other side -- not exactly what you would expect from a nearly $5000 oven. Recently, the display has been blinking in codes and the oven has been turning itself off. When I tried to call customer service, I was repeatedly put on hold for 30 minutes after which the system disconnected me. When I finally spoke to a person, she was very rude. This is a horrible company, a horrible product and I deeply regret that the salesperson at the store talked me into buying this awful oven. I am extremely unhappy.

I was a bit anxious when I purchased my Dacor range because I really didn’t know how it would perform. A year later and I couldn’t be happier. I love my Dacor 30” range. It has been one of the best purchases ever.

We did a complete kitchen remodel in 2007. I wanted top of the line appliances, and I liked the look of Dacor. I spent over $10,000 on a refrigerator, oversize dishwasher, microwave oven and a warming oven... (I know). Within 16 months, everything started to fall apart. Of course it was over the one year’s mark so there was no replacing of the units on the manufacturers part. I have since replaced the motherboard on the dishwasher twice... total of 3K in repairs! I cant replace the dishwasher because it was oversized and we built our cabinets around it and no other company sell an oversized dishwasher. I have replaced the microwave oven with another one that looks just like it because for some reason it fried. The refrigerator constantly rattles and my husband and I are at our wits end because of it. The only thing that hasnt fell apart yet is the warming oven. Probably because we dont use it. I wouldnt recommend it to anyone. Its a total waste of money. Next time Im buying Kenmore. My old Kenmore is sitting out in the garage being a good and faithful second fridge.

We bought our house in 2010 and our Dacor stove was supposedly newer. When I went to clean it, I found loose screws in the bottom. Apparently, the convection element is loosing its screws and washers. Ive had this appliance fixed once already when the cooktop kept clicking. The black plastic around the controls cracked mysteriously. It takes 3 hours longer to cook a turkey than it should. This is a strange stove, which supposedly cost a lot. I wonder if a convection part missing two screws should be used?

Im reading all these reviews and my story mirrors them all... I have actually contacted a lawyer and am considering either a lawsuit or going to small claims court because, at this point, its cheaper than continuing with repairs every other year. Has no one else considered a lawsuit under your states lemon law? Appliances are usually covered. I purchased the MORD230 wall oven in 2008... It was purchased as a second oven to my 6-burner Wolfe to cook a turkey or roast during the holidays. It has been used no more than 24 times... I have gone through 2 control panels and am now having glitches with the third. After doing a self clean recently the whole heating element blew - it will not heat at all. I am able to enter the temp but the oven just runs and runs and never heats. I have called Dacor furious for how many times this thing has broken in relation to how many its been used... They have offered parts at a reduced rate but I am not sinking another dollar in this oven on labor and parts only for it to break again. I asked for my money back and told them to come and get the piece of garbage they sold me. Do yourself a favor and buy a Wolfe... It works beautifully... My only problem was the cast iron grates rusted a bit recently... I called their customer service and was on the phone for no more than 5 minutes and they overnighted me a whole new set no questions asked! Dacor customer service has been a nightmare - so much back and forth... I tell everyone I know... DO NOT buy Dacor!!!

Wow! I wish I had read this website before we built our house 3 years ago. I have a 5 burner Dacor cook-top that has been nothing but trouble since day one! I have 5 different appliance brands in my kitchen and the Dacor is the only one that has caused continuous problems. I was so mad at the repair man today I hung up on him (poor guy, I see now Dacor is the problem). The cook-top has exploded three times. ow when I say exploded, I am not joking at all. I mean the explosion blew the cook-top up and burners off, blew the cabinet doors underneath open, flames shot out and the house shook. One of the times, my one year old son was standing next to it. I was so upset I ran into the other room with him and sat on the floor and we both cried. It was terrifying! I have had a repair man here 6 times over the last 5-ish weeks (Yes, I didnt have a stove over Thanksgiving and I was the host; its not looking good for Christmas either and we have 4 kids). They have replaced, cleaned and fixed everything possible. They then pointed the finger numerous times at the propane company (which they now have determined it is not a propane problem for sure). Today the repair company called me (by the way, they have been constant contact with their Decor rep Rob about the problems) and said they are done. My expensive 3 year old cook top is not repairable. They have exhausted every possibility. They have been here 6 times and the propane company three times. I have a hole in my granite counter top cut specifically for the cook-top and am told that every cook-top is a different size so I do not know what I am going to do. I called Dacor today and asked to speak to someone who could help me to no avail. I then asked for someone (anyone) to call me back today. You guessed it. Theres been no call back. This is getting really old. How many weeks does this need to go on (dont answer that)? Another problem that I have just lived with is that the stove continually clicks for quite a while after you are cooking. I was told to clean it a certain way. I did that and it didnt work. The repair man did it; it didnt work. The repair man said something was loose inside and tightened it. It still didnt work. I guess I could live with the click. It is the explosions that I need fixed.

We remodeled our kitchen in 2001 and bought a Dacor Epicure 30 dual fuel range. The gas cooktop has never been a problem, unlike the oven which has been a problem from the first week with unpredictable temperature variations. Multiple holiday meals have seen the extended family waiting for dinner for two hours because the oven decided to be cool that day. The advice from Dacor: preheat your oven for several hours before you need it or my favorite from a repairman: you must be slamming your oven door. Not helpful. Several expensive repairs later (over $2100) and one fire in the oven now it wont turn on at all. We are going to try one last time to repair it and then we are done. I do not recommend Dacor to anyone - too expensive to have such terrible quality and service.

Over ten years of using my Dacor oven, I have spent $1595 in repair bills to keep it going. It cost $1875 originally and I would have purchased a more reliable brand if I had known how much trouble the oven would cause me.

Our Dacor oven is 2 years old and the oven door stopped closing all the way, rending it inoperable. The company is now owned by Samsung. I tried to schedule a service call to repair/replace the door hinges. This should be a simple process. However, because I purchased the oven through a designer and Dacor dealer, I had to track down the order verification to demonstrate that I am the original owner of the oven (this is in addition to providing a copy of the receipt or proof of purchase). It took several days to resolve this issue with my designer and rep who sold me the oven. Then, I scheduled the service call on the phone only to receive an email hours later advising me that the service call had been cancelled. No explanation was provided. After rescheduling the service call several times only to have each call cancelled, something finally worked with Samsungs tracking system and the service call actually took place.Dacor is the Mercedes of ovens and I expect a service call to be a little more expensive. However, other providers of luxury products facilitate the product support to minimize customer aggravation. Samsung needs to work on its product support and customer service. I would not purchase a Dacor product again since there are several other manufacturers that provide comparable luxury kitchen appliances with much strong customer support.

I am writing to complain about our Dacor dual fuel stove that we purchased in 1998 when we built our house. Initially things went well, and I enjoyed baking in the oven and the convenience of the gas stove top when we had power issues. But then the honeymoon ended, and the problems started. After completing our first self clean cycle, we started getting the F1 code, and noticed cracks in the front on the stove. Our repair guy came out, took a look, and then informed me that Dacor had had numerous problems, and were not so good about living up to their warranty. He was right, Dacor felt in no way that they should help resolve our problem. With 4 kids, you cant just go without a stove, so we paid for the parts and repair. I figured it was just a one time thing, but I was wrong. We are now again looking at replacing the same part just 3 years later again with cracks and the F1 code. Dacor should be ashamed. Do the math. If they walk away from responsibility on all of these faulty products that average $5,000 a piece, shouldnt they have the money to pay for the fixes or maybe hire better engineers? They need to be held accountable for this mess. I need my oven back on!!!! And after the money we have paid for repairs, light bulbs, and parts...... the rest of the care should be free and on them.

We remodeled our kitchen in 2006. I spent a fortune on a Dacor dual fuel gas cooktop with electric oven/convection oven. My Dacor problems seem so normal I mostly deal with it. My 2 biggest complaints are the glass oven door is not airtight, it is darkened between glass, very hard to monitor my baking. And the temp gauge has always been off by 15-25 degrees. I use an in oven temp gauge, which has been calibrated so I know it works. If anyone is planning on a Dacor, you will get the best looking range. It just wont work.

I purchased all Dacor products. First Dishwasher went out, had purchased warranty. Came out 6 times to fix it, filed complaint with Better Business Bureau. Finally got dishwasher replaced with a Kitchen Aid. Thank God for the BBB. They help people. Then my stand alone range with 6 burners had one of the burners go bad, the appliance co. fixed it. Then the oven relay board went defective. Had to order part over $400.00, no warranty. Then wall oven Relay Board went out, 2016. Paid over $460.00.Less than 12 months later relay board went out again. They said Sorry, no warranty. Ordered part said it was $500.00 + to replace. The appliance repair tech ordered wrong relay board. They called me today and now said its going to cost $650.00, no warranty. Do not buy Decor products. They are horrible. I feel I am being ripped off by Dacor and feeling untrusting of the Appliance Co. I may need to file another complaint with Better Business Bureau. Buyers beware!

I was and, I repeat, was a loyal Dacor customer. I gutted and rebuilt a kitchen 9 years ago and purchased a Dacor stovetop, oven and microwave. I remodeled my new house 5 years ago and again purchased Dacor stovetop, oven and microwave. Consumer reports provided favorable reviews of the appliances I purchased below.First red alert: The oven Model MORS130S and Microwave Model DCM 24S LED did not match. The microwave was green; oven was blue. The brochure was in black and white so there was no way of knowing that aesthetically they were a mismatch ... it was very sloppy(!) and very deceptive by Dacor. I mean when I waited weeks for my appliance order and the oven is already installed with a big fat ugly LED screen, what was I supposed to do, yank it out and start all over again? This was disappointing!Next, I was simmering chili on the stovetop (5 burner, gas) and, lo and behold, 18 flames started exiting through the turn knobs resulting in a meltdown. The gas was leaking through the tubes underneath the stovetop. I just happened to check the chili while I was gardening to watch the house almost burn down and btw, it was difficult to put out the flames because the natural gas was leaking under the unit. Seriously! I called customer service and they got hopping right out to fix the issue. This scared the heck out of me. It is negligent to have a product like that on the market.After about 13 months into the life of the Model MORS130S oven, the touch panel failed emitting a CO1 error message. I was told it was $140 to fix it and that the panel was defective, great quality there, Dacor. And the added joy to the CO1 error message is that the unit beeps intermittently all day and all night long unless the power to the oven is killed. Joy... now another issue - Model MORS130S oven LED lights are burning out. Seriously, what else will there be? Now its $175 for LED panel and another $100 to install by an authorized Dacor service man.So I called Dacor back again today because the LED light out was annoying me. They offered nothing. To be fair, my appliances are out of warranty but seriously, Dacor nearly burned my house down. They should be winning me back as a customer if they really cared about their customers and having long term repeat business. Never again, Dacor, never!

I have had my 30 inch Dacor Dual Fuel Range since 2002. In the past month, the oven door seems to be falling apart. I had to replace the oven door handle after the handle cracked in the spots on the right hand side where the screws go in. When I tried to screw the new handle in, I noticed that the front panel on the door is lifting away from the door. It is more separated on the right hand side which leads me to believe that it is the reason that the handle cracked on that side. As a result, the handle cannot be properly installed. The only way this can be repaired is to call someone in to do it and it will either have to be glued together or the whole door would need replacing. Reading these forums, Im worried that my oven problems are just beginning and I dont want to start sinking money into this oven. I purchased a Dacor as I believed it was a high quality product and that it would be worth the money and last a long time. This type of problem should not be occurring. I do not consider 10 years a long time for a product like this. My sister has had her Jenn Air oven for almost 20 years and it has no signs of wearing out.

I have the Dacor 30 all gas range in my house and it is the best. The grates take up the whole top surface of the stove area, so I have a ton of room to cook on. Basically, I can fit 4 giant pots on the stove at the same time, so Im ready anytime a chili cookout might break out. This is also super convenient during tamale season and soup season because I can put up to 4 giant stockpots on the stove simultaneously. In the event that I spill, its easy to remove the grates and give the surface a nice wipe up. As far as the oven, I totally rule the holiday season because I can fit up to 3 full size 18x36 catering sheets in at the same time, so basically, I can cook 4 dozen or more cookies in one shot, leaving me tons more time with family and friends than if I was baking 1 sheet at a time. Thank you Dacor!

This is a follow-up comment from my last post dated June 21st 2011. My local appliance company, where I purchased this oven, seems to have helped with their recent fix. I was able to bake a white cake, following the box directions, that was not burned on one side and raw on the other; it was okay. With fall arriving, I will be back in my kitchen and will be using my oven. I will keep you posted. I still would not recommend this oven to anyone, and will not purchase any future Dacor products.

I purchased a Dacor Renaissance range for our new home. What a waste of money. Though I have not had any major problems with the performance of the range yet, besides uneven baking, the design is not user-friendly. To begin with, the gas burners share a grate. So when cleaning, you have to remove the whole grate on one side. The controls for the burners & griddle are very hard to see & I have to bend over to see which burner Im turning on. The oven racks are a joke. The two glide racks are very bulky with sharp edges. It is difficult to change the heights or to remove them for cleaning purposes. Though there are three racks included, it is impossible to bake with all three in the oven.I have a GE Monogram that I had purchased two years ago for another home, and I love it The Renaissance & Monogram are similar in price, but I unfortunately, listened to the sales person & let them talk me into the Renaissance. I realized my mistake in buying a Dacor immediately & contacted the appliance store. Even though the Renaissance had not been used, they would only give me a token amount of money towards trading it in for a Monogram. So, I am stuck with a range that causes me to swear under my breath every time I use it. Dacor could learn a lot from GE.

Dacor range - After I posted my comments on August 8th, I was contacted by Dacor customer service immediately and the new part was sent to me free of charge. I do have to pay the labor, but the part was what was expensive before. They did give me an explanation as to why this was happening - the hinges on the door wear out and the door doesnt shut properly so that heat escapes. Should this be happening with a stove that was this expensive? I dont think so, but I am happy with the customer service I received from Dacor this time.

Warning: Warning, safety hazzard for all, adults and children. Recommendation: The knobs should be set on the top of the stove, not the front where children can reach. Control knobs should click when fire and gas is turned off, and highest flame setting should be at the end of the turn just like a clock. I inherited this range as new owner of the house. Today I used the high flame option of the gas stove. When I was done with cooking, I turned off the gas according to the knob position, front of the turn. Later I discovered the range was not exactly off. It was still hot but no flame could be seen.I checked by sight the control knob position, it was set incorrectly in off. Then I touched it and realized the knob actually has a bit more to go to the end, slightly before the off position. Therefore it continues to release gas with unobservable flame. This knob does not click when user turns it to the off position. It is just a silent knob with an inaccurate cue of a heavier black line for off and on indication. Besides, high flame setting comes at the beginning of the turn of the knob rather than the end, it is counter intuitive to our mind of increase heat by turning the knob further on, like our clock. Oven racks are hard to put back after cleaning. Once a rack almost tumble out while food was sitting on it.

I completed a 7-month total remodel of our kitchen and family room, which were connected in November 2007. The kitchen remodel cost $18,000 for various Dacor appliances including the Millenia series of wall oven MOV130S; warming drawer MWDV30; and 42 island hood DHI42130. The remaining includes the huge 30 Epicure dishwasher ED30SCP, 36 cooktop EG366SCH, and beverage center EF24LBCSS. All have the beautiful copper accent package and make for highly attractive appliances. We constantly receive accolades for them. If only they werent absolute garbage functionally and reliability-wise. Others have remarked how the ignitors on the cooktop continually spark, even after the light off. After contacting Dacor and waiting 2 weeks for the repair, for which Dacor sent the wrong part and caused another 2-week delay, the repairman had to rip off the front accent lip of the cooktop to reach the base which significantly dented the front lip. The ignitor worked like a champ for 2 days, then click, click, click - constant ignitions. So I cleaned around the ignitor tip with 409, dried it and it worked flawlessly. Thanks Dacor for your own product ignorance and my now dented cooktop. It has worked well since and is a sound product, so far. If only my luck held out.Next, the wall oven. Very beautiful and my control panel has held out (fingers faithlessly crossed). The oven isnt calibrated though, so follow cooking directions at your own risk. This oven will burn your food if you set the temp and timer to the recommended settings. I have to take off 25-50 degrees and 5-10 minutes of requested cook time or I will smoke any meal. After 2 years of use, I decided to use the cleaning cycle - following the directions to the letter. Forty five minutes into the cycle and kaboo! The front window shattered. Dacor says $700+ for glass replacement; I say send me the part and Ill do it. I got the discounted part for $68; spent 3 hours cleaning and reassembling with care; and the window has held, but I havent tried the cleaning cycle since. Why roll the dice again?Ah, now my fave garbage Dacor appliance - the interminable dishwasher. Truly engineered by the diabolical. I just completed my fourth major repair after 5 years of use. First, the drain valve failed after a few months of use causing flood and was replaced under warranty. Then the door seal failed (more flooding) and was also repaired and replaced under warranty. The dishwasher stinks, by the way, as the unit cannot evaporate effectively during drying cycle due to ridiculously poor rear venting design. So I have to leave the door wide open for hours after use to facilitate drying and stench reduction. The control panel/circuit board has fried twice now in the last 3 years - it just starts erratically beeping and refuses to take input, even with a power reset. Both technicians stated the design and quality of the board is third world, which likely is exactly where Dacor outsourced the garbage.The island hood and warming drawer have worked well, and the beverage center has been reliable but maddeningly causes back left cans of soda to freeze and explode occasionally; even with the set temperature raised to now 45 degrees. Fun to clean up after coming home from a long trip. My expectations are so laughingly low now for these Dacor products that I dont bat an eye with the frozen soda muck this fridge occasionally produces. Customer service though has been helpful and thankfully, American. They have replaced both circuit boards for free well out of warranty. I have only appreciation and great sympathy for the customer service folks who Ive spoken with. I love my kitchen, but hate the appliances in it. Never again Dacor. Never again.

Front bevel of my first rsd30 range purchased in California in 1999 cracked within nine months. Dacor said it was a defect in the design and would fix it for free. I sold the house in 2001 but the range was still not fixed. I moved to Nevada and bought a new rsd30 range and same thing happened within six months. It took a year to get it fixed at their expense. This bevel also cracked again for the second time in March 2011. Their response to this was to offer me a new bevel for $180 and I would have to pay for the installation. I declined the offer. The bevel is still cracked at this time. At the same time, I bought a PMOR30 over the range microwave and the front handle broke at least four times. And finally, the whole thing broke down and was not repairable. In Aug. 2008, I contacted Dacor and they agreed to replace it with a new DMT2420 over the counter microwave for half the price ($390). Last week, this one blew up on me. Sparks were coming out through the side and a big hole in the removable shield and burn damage to the wall of the unit. I do not believe this unit is repairable. I contacted Michael at Dacor. He apologized and said that theres nothing they can do about it as it is out of warranty but they will look into it. What I want at this point is my money back that I paid for ($390) and for them to pick up the unit and get it out of my house. I will never buy another Dacor product again.

We built a home in 2006 and installed all Dacor appliances. I would never ever purchase these products again. My gas cooktop was the top of the line product from Dacor and I have had nothing but problems with it for 5 years now. I have spent over $1000 fixing the large burner that continues to have leaks with the seal to the point where the flames come out the bottom of the burner. Most of the other burners click when lit even though they are clean and away from a draft. I have had 2 Dacor approved repair companies out and they both recommended against Dacor. In addition, the finish on the cooktop has soaked in my heavy duty cooking juices and foods and the stains will not come out. Apparently, this is due to the new finish they used so that the metal can withstand the high temperatures. If this company were an auto mfg., they would have had to do recalls and face potential class action suits. I would prefer to be cooking on a camp stove rather than my Dacor. When I contacted Dacor, they offered parts at a reduced rate which still cost a fortune. When I asked about replacement, they said they would sell to me at a discounted rate which was still $2400. Bad product, bad company. My cooktop is still giving me issues. it is embarrassing to cook with friends around because of the problems.

We purchased a DACOR double wall oven (MOH2275) in April 2012. We are waiting for service to arrive for the fourth time since we purchased the oven. I find this unacceptable. We have had 2 other ovens in the last 30 years and they did not need any service. In general I have found appliances to be of such reliability that I dont get extended warranties. DACOR gave a 3 year warranty on this oven and now I know why. Hopefully this service will fix it for a long period of time.On the positive side, the oven really works well. It is so well insulated that we feel very little heat coming off it. One serious flaw its overall operation is the reheating of the oven. If I bake something at 350 degrees and then want to reset the over to 450 degrees, the oven does not go into preheat mode and does not let you know when you reach the required temperature. I am hopeful this will last awhile and not have to be replaced for what we paid for it.

We purchased a Dacor induction range 5 years ago which cost $5000 plus installation parts and service costs totalling $10000. Two days ago, an error code showed up indicating that the generator needs replacement. I contacted Dacor who states that the part is discontinued but that I could contact a refurbishing company (Corecentric) to send my generator to for possible repair. A service technician would have to remove the generator, I would send the part to Corecentric, then IF they can repair it, the tech needs to reinstall it. There are no service providers that Dacor referred me to that will service a refurbished part. Even if I wanted to try, I as an owner, cannot remove it myself because Dacor does not provide the service manual to do so. I spoke to Dacor multiple times about this problem and management stated that since the product is so out of warranty that they cannot offer any other repair option, compensation, or replacement even if the part is deemed unrepairable by Corecentric. When you pay $10000 for a product I expect it to last more than five years and that a reputable company would stand by their product and service. Essentially, Dacor inferred that we are out of $10000 because a part that POSSIBLY can be refurbished for $215 plus service costs, cant get serviced and Dacor takes no further responsibility. I have heard stories from appliance providers and service providers that since Dacor joined Samsung, that their customer service is poor and products have become inferior.

The wall oven’s glass was damaged by a guest. Customer service at Dacor was exceptional. Within a day of advising Dacor’s customer service, I received a call from the service man and the replacement was installed the very next day. The service man was considerate by calling first and coming exactly when he said he would. He was very professional as he replaced the glass in a matter of minutes. I would choose Dacor again.

We purchased this unit 7 years ago, just a family of two with visiting grandchildren. Unit came, had a crooked door and a bent latch, which we had serviced and supposedly corrected. When self cleaning the latch still made grinding noises. Over a year ago the oven stopped working period. A December service call said needs a new latch, sensor and display -we are now in 4 figures($). Oven operates for month and a half. January 2019 Service call now new door latch, relay board and main wire harness 4 figures again double! Oven stops working yesterday (June). Service call today new latch, motherboard and something else and another 4 figure repair cost. Same repair parts same problem! Patience is a virtue, but repair costs are sinful! Next step, Boat Anchor! Problem from the beginning and still a problem now.

We have a dual fuel Dacor oven purchased in 2001. We have the manual. For some reason, after cancelling a timer, the oven locked at :4. The owners manual was no help. The Dacor website was no help. We turned off the circuit breaker then turned it on again and finally, the oven worked.

We had a ongoing problem with a wall oven that was purchased in 2006. The most recent complaint was a oven glide rack that was not working. After complaining about it to one of their staff, they listened to our frustration and are sending us a new rack at no charge. My hats off to the great people at Dacor. Thanks for your understanding. Al

I had a Thermador kitchen for more than 25 years and I was very happy with their products; I had a Thermador slide-in range with downdraft vent and a dishwasher and a KitchenAid refrigerator, but it was time to upgrade. Now, I upgraded my whole kitchen with all Dacor products and I am super happy, my 30 inch range top has extra wide grates which allows my wife to cook with extra large pans when she prepares food for donation, my updraft vent catches smoke and grease much better than my downdraft, my refrigeration is very nice looking with french door and middle refrigeration for my cold drinks and my dishwasher is very quiet. I invited a few friends home and they have admire my new kitchen. It has been more than months since I bought it and no problems.

Weve had these appliances for 15 years. The cooktop has worked well. However, it could be improved with a lower lever for heating on its small burners, allowing it to simmer water rather than boil. The Dacor exhaust we purchased is one of those type that pop up out of the counter. It works but leaves much to be desired. When it runs, it pulls so much air the flame goes out on the burners. It is still not efficient at getting rid of cooking smells or smoke either, but that is simply a problem with all of this design so I cant fault Dacor. We have the biggest problem with the double oven. There are three main issues: 1) Whenever we run the self cleaning function, it pops the heat safety switch inside the oven housing so I need to take it apart to fix it. Hence we work to keep it clean so we never use the cleaning cycle. 2) The oven door gaskets prevent to door from closing and sealing all the way. The door tilts out app. ¾ because of this. We were told by the service guy who came to fix problem 1 above that this is the way the doors are(!). Our bottom one also tilts out but not as much. Ive dealt with this for 14 years! 3) We have to sand the burner electrodes on the cooktop to ensure they spark to light the burners at least 2-4 times per year. Not sure if that is normal or not.

Dacor ERD30S06CHLP 30 Inch Epicure Series Freestanding Dual-Fuel - I am so dissatisfied with this product. We bought the first range in 2003 and were so excited to use it. We chose Dacor over Wolf. From the beginning we had issues with the oven. It cooked very unevenly and the door never closed properly. We had a service call and they basically told us that we got a lemon. They offered us a new range for $3.5K. We thought we got a lemon so we agreed and paid for a new one for $3.5k. We also purchased the extended warranty for $2.2K.0 This one was even worse.One time I opened the oven and it burned my eyelashes. I wrote and complained with a video of the explosion and had to pay for the service call. I wrote a review in the website and they deleted it. We now own a range that we have paid over $10K that bakes unevenly, electric element does not work in oven and have minor explosions from time to time with a door that does not close. We have a few friends who have asked us about our range and we always recommend against it. We are looking for a new range. I would not recommend this range. I thought we got a lemon. But it seems thats just the product.

We purchased a very expensive Dacor double convection oven about 15 years ago. This was based on recommendations from friends who do a lot of cooking like we do, and the mistaken thought that this US company would be more inclined to support any future problem. We now have a problem with the control panel. Dacors only response is that they do not make the part anymore and cannot help us remedy the problem. They even had the nerve to say that they would give us 10% off a new one. Except for the annoying buzzer sound, the stove works well. Buying a new one is a financial burden we never expected or want to accept. We are telling all of our friends to stay away from this manufacturer. I wish I did not have to give Dacor any stars.

I went to put something in the cabinet at the top of my built-in wall oven and noticed the cabinet door was warm. Then, I noticed the heat was coming from the top of the oven at the control panel. I am afraid of a fire breaking out in the cabinet now. The oven is less than a year old. We just remodeled our kitchen and installed the ovens in May 2012 and this is just June.

As I have read in most of the reviews, we have also experienced the control panel on our 30 inch dual range cracking over the years. We were told not to replace it because it would continue to happen. Ok, lived with that... Now something new has started to happen, the plastic handle on the oven door and surrounding area has started to melt. It got so bad after a self clean that it is collapsing. Now there isn’t much of a seal at all when the door closes. The stove isn’t brand new, but this has to be a fire hazard, and consequently, now the oven will not even turn on. I’ve reached out to Dacor with no response yet. I’m done with this company!

I spent a lot of money buying a Dacor double wall oven because it was supposed to be top of the line and dependable. Now, the circuit board needs to be replaced and the oven is just 5 years old! This seems absolutely ridiculous for an oven this young to have such a major problem! I am very upset about all the money I am going to have to spend to fix it. Ive never, ever had any oven problems with other brands like this in my life. We remodeled our kitchen and I thought I was getting something better and now I realize that this brand is not living up to my expectations at all! I am using an authorized Dacor repair company and they told me that they are seeing lots of problems with this brand. I do not recommend this oven to anyone.

I rarely write reviews but when I found your site, I decided it was time to vent. I bought a 36 dual fuel, convection Epicure range in 1999. It was not a cheap oven and I was excited at the possibilities of having a 16,000 BTU broiler and large oven cavity to work with. Lets just say that excitement quickly wore off. Almost immediately after the range went out of warranty, the ignitors went bad and we also had to replace the control panel ($400 in repairs was a lot back then). After that, we continued to have ignitor problems and replaced them again. Finally, I just stopped doing it and lit them with my aim and flame. I never allow my children to cook on the stove because I am afraid they will be burned. Most recently, my broiler element, relay board and again more ignitor problems ($1,200 in repairs). Not to mention, the repairman had a terrible time trying to access all the areas and was at my house for 4 hours trying to do so. When the initial problems happened, I emailed, phoned, left message, etc. to no avail with customer service (I use that term loosely). This company is the worst. I have told everyone I know never to buy a Dacor anything. Next time, Ill buy a Wolf.