My ovens have had to have a new board, dishwasher rarely works, my cooktop cant get parts needed! The worst appliances on the market!

I have a Dacor MORS130SS oven that I purchased in July of 2008. After 6 months the first membrane panel failed, one year later the second membrane failed. One year later the third membrane failed. Im on the fourth membrane and now my fine Dacor is burning things!! I can set the temp to 350 and it shows 350 on the display but the lower element never shuts off and whatever I cook gets burned. I bought this oven thinking it might be my last considering the supposed quality of Dacor. I know for sure it wont be my last oven!! I sell appliances and I never recommend Dacor ovens because of all the continued problems. Ive never used the self clean feature since being told by a Dacor tech trainer that he didnt recommend using self clean because it would cause the oven to age faster. Wonder how long it would have lasted if I did use self clean? Sure wish Dacor would contact me for a testimonial!

Purchased home with installed Dacor double oven. Oven wouldnt reach set temperature, so replaced control board. Doable, but a real hassle to remove oven from wall opening and label, disconnect, and reconnect 20-something wires. Two years later, the clock cannot take the correct time and oven timers do not work. Only fix: replacing the $300 control board again. I cannot recommend that anyone purchase these appliances as the control boards simply do not work for more than a couple of years.

I emailed Dacor for information about how to get my range fixed and was amazed. My questions were answered complete with numbers for model and needed replacement parts along with contact information for local service folks. Amazingly good service. Bravo, Tori **! Give that woman a raise!

Warning: Warning, safety hazzard for all, adults and children. Recommendation: The knobs should be set on the top of the stove, not the front where children can reach. Control knobs should click when fire and gas is turned off, and highest flame setting should be at the end of the turn just like a clock. I inherited this range as new owner of the house. Today I used the high flame option of the gas stove. When I was done with cooking, I turned off the gas according to the knob position, front of the turn. Later I discovered the range was not exactly off. It was still hot but no flame could be seen.I checked by sight the control knob position, it was set incorrectly in off. Then I touched it and realized the knob actually has a bit more to go to the end, slightly before the off position. Therefore it continues to release gas with unobservable flame. This knob does not click when user turns it to the off position. It is just a silent knob with an inaccurate cue of a heavier black line for off and on indication. Besides, high flame setting comes at the beginning of the turn of the knob rather than the end, it is counter intuitive to our mind of increase heat by turning the knob further on, like our clock. Oven racks are hard to put back after cleaning. Once a rack almost tumble out while food was sitting on it.

We remodeled our kitchen less than 5 years ago. As we have owned restaurants in the past, we wanted commercial quality appliances. I was looking at Sub-Zero and Viking or Wolf. Unfortunately I took my Home Center convince me to purchase A Dacor package. That was a mistake. Even though these appliances cost as much as the those brands, the quality is not even close. After spending $22,000 on appliances I have quickly discovered that these appliances are junk. First the microwave began to arc and nearly caught fire. Even when they installed my cooktop. I noticed that the burners in the middle were marked incorrectly and the blue LED indicating the burners are on was burnt out.After only a few years, now my ovens are not working. And right before Thanksgiving I am without ovens. My old ovens were almost 50 years old and worked fine. These $6000 plus ovens are not even 5 years old and are down. I am kicking myself for not going with my original plan. If you are considering Dacor, I would not recommend.

Two years ago, we redid our total kitchen at considerable expense. All of the appliances we replaced were made by Dacor. They included: 1) a 36-inch refrigerator model EF 36/wf; 2) a dual wall oven, model EO230SCH; 3) a gas cook top, Model RGC304; 4) a dishwasher, ModelEDWH24S and; 5) a range hood, ModelEH3012SCH. The problems started within a two months of installation. The refrigerator stopped running due to a relay failure and a compressor problem; both were replaced by Dacor at no cost to us. It was inconvenient but not costly. A short time later, the lower wall oven stopped working as well as the lights in both ovens. This required the replacement of the main control panel (control circuit board). Dacor paid to have it repaired. The clock does not keep accurate time and gains about an hour a day. We decided to leave it well enough alone and did not have it fixed. After the one-year warranty expired, the lower oven quit again. This time, it had to be removed from the wall and an exhaust fan in the lower oven was defective and had to be replaced. Dacor’s initial response was it was out of warranty, so it was up to me to cover repairs. They eventually agreed to supply the part (about $90) but we had to spend several hundred dollars to install. Now, the lower oven takes an extremely long time to heat up, and again we decided to leave it well enough alone. Recently, there was a loud flash in the vent hood; one of the bulbs apparently burned out. My wife tried to turn off the lights in the hood but the light switch apparently blew when the light went and could not turn them off. After a couple of burned fingers and a melted bulb removal tool, I managed to get the other bulb out. A call to Dacor got the usual out of warranty response. I called the local Dacor authorized service rep. He looked at the problem ($95) and said he would have to call Dacor. After he talked to Dacor, they called me and said they would send a replacement control board but would not pay for the service calls. The service company said the next service call would be $195. One light bulb burned out: cost $290. I suspect that every hood unit that Dacor made with this control board is also defective. We have had to replace the halogen bulbs with great regularity. We have halogen bulbs in our boat that have lasted at least 15 years. There was another complaint on this board that had a similar problem with the vent hood. He decided to fix it himself. He is an Electrical Engineer his comments are worth reading and speak to the inadequate design of this unit. It is a shame that the Dacor appliances appear to be near the bottom in terms of reliability. Consumer Reports that their gas cook tops appear to be the least reliable. It looks like I have something to look forward to. Needless to say, I cannot recommend Dacor to anyone. In fact, I would recommend that they not purchase any Dacor product that does not have a full multi-year warranty.

I purchased a Dacor Renaissance range for our new home. What a waste of money. Though I have not had any major problems with the performance of the range yet, besides uneven baking, the design is not user-friendly. To begin with, the gas burners share a grate. So when cleaning, you have to remove the whole grate on one side. The controls for the burners & griddle are very hard to see & I have to bend over to see which burner Im turning on. The oven racks are a joke. The two glide racks are very bulky with sharp edges. It is difficult to change the heights or to remove them for cleaning purposes. Though there are three racks included, it is impossible to bake with all three in the oven.I have a GE Monogram that I had purchased two years ago for another home, and I love it The Renaissance & Monogram are similar in price, but I unfortunately, listened to the sales person & let them talk me into the Renaissance. I realized my mistake in buying a Dacor immediately & contacted the appliance store. Even though the Renaissance had not been used, they would only give me a token amount of money towards trading it in for a Monogram. So, I am stuck with a range that causes me to swear under my breath every time I use it. Dacor could learn a lot from GE.

We purchased a Dacor wall oven to replace a GE oven that was outdated. We thought we were getting a premium appliance, but after less than a year and just before the holidays it quit with a code on the control panel we couldnt find in the owners manual. We had a serviceman out and the cost of the part and the service call was more than we paid for the oven! It now sits there, useless and a reminder to never buy Dacor anything!

After remodeling our kitchen, we purchased a professional line Dacor stand alone gas range/oven. Within a year, the heating element needed to be replaced. Subsequently, the control panel almost caught fire and needed replacement, following a second heating element. The oven is not reliable and has cost us over $600 in repairs, labor and parts. The Dacor company is not willing to recognize that this oven is a lemon, even though their rep admitted that the number of repairs seem to exceed the average number. The company refuses to pay for a tech to come in to examine why this range continue to have electrical problems. It is not working again, and the customer service rep wants us to pay out more money to have their tech diagnose the problem and pay the cost of repairs and labor, while they will cover the cost of the parts. I am done paying out more money on a defective appliance. I could have purchased two new less expensive (and more reliable) ovens by now.

Im reading all these reviews and my story mirrors them all... I have actually contacted a lawyer and am considering either a lawsuit or going to small claims court because, at this point, its cheaper than continuing with repairs every other year. Has no one else considered a lawsuit under your states lemon law? Appliances are usually covered. I purchased the MORD230 wall oven in 2008... It was purchased as a second oven to my 6-burner Wolfe to cook a turkey or roast during the holidays. It has been used no more than 24 times... I have gone through 2 control panels and am now having glitches with the third. After doing a self clean recently the whole heating element blew - it will not heat at all. I am able to enter the temp but the oven just runs and runs and never heats. I have called Dacor furious for how many times this thing has broken in relation to how many its been used... They have offered parts at a reduced rate but I am not sinking another dollar in this oven on labor and parts only for it to break again. I asked for my money back and told them to come and get the piece of garbage they sold me. Do yourself a favor and buy a Wolfe... It works beautifully... My only problem was the cast iron grates rusted a bit recently... I called their customer service and was on the phone for no more than 5 minutes and they overnighted me a whole new set no questions asked! Dacor customer service has been a nightmare - so much back and forth... I tell everyone I know... DO NOT buy Dacor!!!

We remodeled our kitchen and decided to use the range as the focal point of the room. The decision to go with a Dacor ER36DSCH dual fuel range over comparable Wolf and Viking models as well as a Dacor heating drawer was made, a decision I have regretted since. Our unit keeps blowing the baking element ($200) which routinely fails at the most inopportune times. To date I have replaced four and the Mrs. recently informed me that the oven is once again not heating properly. Thankfully, I am competent enough to diagnosis and repair it myself and did a thorough operational inspection and cleaning which revealed the broil element ($180) had also gone bad this time. My wife hates this oven and unfortunately it sits right smack in the middle of our beautiful kitchen to remind us of the bad decision we made. In fact, we are now at the point where we are considering replacing it and sending it to a scrap yard where it belongs. Avoid this brand or it will cost you.

We purchased a Dacor Epicure dual fuel range when we built our house 7 years ago. It was the most expensive appliance we bought and we wish we hadnt. We have had no problems with the stove top, but the oven, specifically the broiler unit has been a consistent problem. We rarely use the broiler and use the oven perhaps 2 or 3 times a month. Yet, the igniter had to be replaced in March of 2008 and again, in June of 2010. In January of 2011, the broil gas valve was changed and now in September, the broiler is again not working. I cant see pouring any more money into this appliance and will sell as soon as I find a buyer willing to take a chance on it. We have been greatly disappointed in this product.

We purchased a very expensive Dacor double convection oven about 15 years ago. This was based on recommendations from friends who do a lot of cooking like we do, and the mistaken thought that this US company would be more inclined to support any future problem. We now have a problem with the control panel. Dacors only response is that they do not make the part anymore and cannot help us remedy the problem. They even had the nerve to say that they would give us 10% off a new one. Except for the annoying buzzer sound, the stove works well. Buying a new one is a financial burden we never expected or want to accept. We are telling all of our friends to stay away from this manufacturer. I wish I did not have to give Dacor any stars.

We remodeled our kitchen in 2016. We chose Dacor 30” range. The gas oven has been a disaster. After less than a year, it wouldn’t heat. They replaced it, same problem. Replaced the igniter and valve, same problem. Now they will do nothing and say we’re on our own. Problems with hood and fridge too. Stay away from Dacor at all costs!

I first bought the low-end Dacor dual fuel range and overhead microwave oven. Within the time frame of 3 years, repairs to the stove cost over $2,500. The stove cost $1,800. Ever single piece of plastic on the stove cracked and had to be replaced multiple times. The microwaves handle cracked 6 times, twice in one week. The overhead trim, which is about 30 by 6 and heavy, fell off and hit me in the head while I was frying bacon. If it had hit the pan of hot grease, I would have been burned. I contacted Dacor and got the brush off. I contacted Fight Back with David Horowitz about the problem. Dacor called me back, bowing and scraping, and we came to an agreement that they would take back the stove and microwave and put the full cost towards an upgrade to their high end model. I am sure you think I was stupid but the stove cooked beautifully and I thought a stove with no plastic trim pieces would solve the problem. Wrong! The microwave control panel has gone out twice, each repair costing around $350. The handle broke 4 times but that was covered under warranty. The front control panel has died 3 times (another $350 each time). The broiler dies each time the self-clean is used and that has been fixed 3 or 4 times. Some computer board on the top of the stove has died (another $400). The enamel lining inside has cracked, crazed, chipped off and rusted. Now, the front control panel has died and so has the one on the microwave. Times are very tough for us now and I cant afford to get them fixed. I noticed that the front panel trim on the top of the microwave is starting to pop out again (plastic fatigue). Hopefully, it will fall off again while I am cooking and hit me in the head and knock some sense into me. If it does happen, I will take them to court.

Dacor 27 electric double oven unreliability. Almost from first use the Dacor electric double oven has been plagued with problems including but not limited to door not locking when self cleaning, not self cleaning, door not unlocking upon completion of self cleaning, and filter issues. Since purchased in 2013 the top oven has been used between 75 and 100 times; the bottom oven less than 25 times. Yesterday the oven died. First error message U43 relay board. Second U60 cooling fan. Worse when the control board responsive/froze circuit breakers were needed to turn oven off.Repair estimate is $1600 plus tax. I intend to replace the overpriced and unreliable Dacor with a Kitchen Aide at approximately 13 the price based on customer and Consumer Reports reviews plus a new one year guarantee. I do not recommend the Dacor double oven if you are a serious cook and/or frequent user. Brand name and styling are less important than product reliability and useful life especially when you can purchase the former for two-thirds less money.

It give the peace of mind, knowing that having a Dacor cooktop (RGC365) I have one less thing to worry about it. Food is always on time, and my wall oven is so simple to use and clean. Like I said one less thing to worry about it. I been a Dacor customer for over 12 years. There is no need to look any farther. My next kitchen will be a Dacor Set.

I purchased a 48 Dacor Epicure stove in October 2010. We moved into our home in November just in time for Thanksgiving. We remodeled the kitchen and the stove is the focal point. When I heated the two ovens, the pre-heat mode stayed on but the ovens went to 600 degrees plus. My oven thermometers only read to 600. That happens every time and the fans stay on for hours. After many service calls, we have determined that the oven is going into a cleaning mode every time and is wired backwards. Dacor is ignoring me.

We purchased a home with a 5 year old Dacor Discovery IQ Double Wall Oven. Model Number DYO230S. Great looking and it has a very sophisticated and functionally rich digital control system. Problem is the digital control system does not work. The stove has a mind of its own and will just shut off for 24 to 48 hours and return to function randomly. Shutting the power off and turning it back on has no effect. Dacor (Now Samsung) has been completely un-helpful. Bottom line response - tough. Product is no longer produced, replacement parts no longer in stock - maybe there is a part on eBay ** Honest that is the answer. I have called parts companies who also complain about Dacor (now Samsung). No luck. So we will now need to purchase a replacement product for anywhere from 4,000 to 10,000 dollars. To replace a 5 year old - 8,000 product. It will definitely not be a Dacor or Samsung product. And I will do my best to put similar reviews on the internet where ever I can.Just to add some balance - 21 years ago we custom built a home and purchased two Dacor ovens. Both were great. 21 years of flawless operation. When we saw this oven as we went through the home purchase process we were delighted. What a disappointment. Also - before the oven started to go wacky on us we needed to replace the bulbs (2) in the oven light fixture. Initially I contacted Dacor parts and had a very pleasant experience ordering the two replacements. However nothing came to our home. Called again and found that Dacor had been sold to Samsung and the price of the bulbs had doubled or more. No exaggeration. Stay away from Dacor and Samsung.

We did a complete kitchen remodel in 2007. I wanted top of the line appliances, and I liked the look of Dacor. I spent over $10,000 on a refrigerator, oversize dishwasher, microwave oven and a warming oven... (I know). Within 16 months, everything started to fall apart. Of course it was over the one year’s mark so there was no replacing of the units on the manufacturers part. I have since replaced the motherboard on the dishwasher twice... total of 3K in repairs! I cant replace the dishwasher because it was oversized and we built our cabinets around it and no other company sell an oversized dishwasher. I have replaced the microwave oven with another one that looks just like it because for some reason it fried. The refrigerator constantly rattles and my husband and I are at our wits end because of it. The only thing that hasnt fell apart yet is the warming oven. Probably because we dont use it. I wouldnt recommend it to anyone. Its a total waste of money. Next time Im buying Kenmore. My old Kenmore is sitting out in the garage being a good and faithful second fridge.

We bought a new house a couple years ago, and the kitchen came with a suite of new Dacor appliances - range, fridge, and dishwasher. They are all terrible.The led indicator on the dishwasher is scrambled. The icemaker in the fridge clogs up into a solid block of ice. We had this fixed, which involved a new control board and some caulking, but the problem returned not long after. The knobs on the range feel like theyll snap off any time. The lights in the oven arent seated properly and they interfere with the oven racks. It takes forever to get up to temperature. And Im starting to think I have a gas leak. How can these products be so expensive and such utter garbage? Oh, but they have wifi!

We remodeled our kitchen because my wife is a chef. So we thought a full suite of Dacor products was just what she needed. What a mistake! Our $6000 36-inch dual-fuel range had problems from the start. We had to replace the control panel, heating element, convection fan, and door seal. Finally, the liner split and the range became unrepairable. We made the mistake of purchasing a simpler, gas-only range because Dacor offered a modest discount. This $7000 range lasted four months before a failure in the wiring harness made it unrepairable!! We bought a Miele replacement. We have had performance issues with our Dacor warming drawer and microwave. DO NOT BUY ANYTHING DACOR!!!

We built a home in 2006 and installed all Dacor appliances. I would never ever purchase these products again. My gas cooktop was the top of the line product from Dacor and I have had nothing but problems with it for 5 years now. I have spent over $1000 fixing the large burner that continues to have leaks with the seal to the point where the flames come out the bottom of the burner. Most of the other burners click when lit even though they are clean and away from a draft. I have had 2 Dacor approved repair companies out and they both recommended against Dacor. In addition, the finish on the cooktop has soaked in my heavy duty cooking juices and foods and the stains will not come out. Apparently, this is due to the new finish they used so that the metal can withstand the high temperatures. If this company were an auto mfg., they would have had to do recalls and face potential class action suits. I would prefer to be cooking on a camp stove rather than my Dacor. When I contacted Dacor, they offered parts at a reduced rate which still cost a fortune. When I asked about replacement, they said they would sell to me at a discounted rate which was still $2400. Bad product, bad company. My cooktop is still giving me issues. it is embarrassing to cook with friends around because of the problems.

As I have read in most of the reviews, we have also experienced the control panel on our 30 inch dual range cracking over the years. We were told not to replace it because it would continue to happen. Ok, lived with that... Now something new has started to happen, the plastic handle on the oven door and surrounding area has started to melt. It got so bad after a self clean that it is collapsing. Now there isn’t much of a seal at all when the door closes. The stove isn’t brand new, but this has to be a fire hazard, and consequently, now the oven will not even turn on. I’ve reached out to Dacor with no response yet. I’m done with this company!

Updated on 05/11/2021: I wrote a review about my terrible Dacor stove, and I was amazed when I was notified within a couple of days that Dacor wanted to help resolve my issue. I was asked to provide some basic personal information, which I dutifully supplied. That was weeks ago and I havent heard a peep since, and I doubt I will. Clearly they do this just so they can mark these reviews as Resolution in progress to make it seem like theyre doing something to help. But as far as I can tell its nothing but a smokescreen. Dont be fooled by resolutions in progress.Original: Our Dacor stove is the worst stove I have ever owned or lived with in my 50+ years. Within 2 years after we bought it, the oven had stopped working twice and 2 of the 4 knobs broke. (Ive never had a knob break on any stove before.) Luckily an appliance repair person (not specific to Dacor) was able to get the oven working both times but told us replacement knobs were not available. We have tried generics but nothing fits. I have been juggling 2 knobs on 4 burners for more than 3 years now, and STILL Dacor has no replacements available. Six months ago we inquired again and were told they had a new model of knobs available that would fit, but we ordered them and they were on back order and never became available. Meanwhile Dacor had already processed our payment for them (which is illegal, I believe) so we had to deal with getting that refunded because our hope of the knobs ever being in stock was gone. This is also the loudest electric oven Ive ever owned. It sounds like convection is on every time you use it, whether or not its actually set on convection. That lasts for 20 minutes after you turn off the oven, too. Also, periodically the stove emits a loud BEEP and resets its computer for no apparent reason, sometimes when Im cooking (oh, you had a timer going? TOO BAD - who knows when it will be ready now!) and sometimes when the stove isnt even on at all (just thought you might like to reset the clock - AGAIN).Furthermore, the oven door has a special design with an open space at the base that allows dog hair to get sucked in from under the stove and collect between the 2 layers of glass. So we get to view our food through dirty HAIR. Apparently thats why the oven is so loud, because it takes a lot to suck up all that hair from under the stove. This can be cleaned, but you have to remove the door to get to it, which is not easy - I cant do it myself. Its so embarrassing when we have people over for dinner; I just hope nobody notices the hairball in the oven door. After reading through the other Dacor reviews I consider myself lucky to be able to cook at all. Buyer beware, dont EVER buy anything from this brand. Its total (expensive) crap and customer service is nonexistent.

We purchased our range (Dacor Dual Fuel Range RSD30) in about 1997 thinking we had a good investment. We have replaced the bezel 5 times (the area that encloses the control area). Today the door glass has cracked. Whooppee! Merry Christmas! Each time I called about the bezel, I was told that they had a design flaw. The last time we had to replace the bezel and also pay for installation ourselves. We decided if this happened again, we would get rid of it. Well, it will be sooner than later as the oven glass has cracked. Needless to say, we are not return customers.

My Dacor (3 years old) oven top burners igniters dont stop after being turned on, although they are burning. Ive tried drying them for many hours and applying rubbing alcohol. The front ones do this all the time when we turn them on. When we turn the left front burner on, the front right ones igniter does it along with the left! The back ones do it occasionally, so are still usable. Apparently this is a common problem with Dacor units. Why havent they fixed it? Weve had them fix the electronic panel at huge expense, and are not going to call them again. When the back burners stop working, well get another unit. Ive had gas stoves for 30 years and have never experienced anything like this poor quality. Its amazing that they are still in business.

I have been getting the run around from Dacor regarding a part that I paid $700 to fix an interior light that comes on and off like a strobe light. After the local service company installed the part, recommended as the fix by Dacor, the issue returned. I contacted the technician again and that is when the run around started by Dacor. I was told to contact the customer service line and tell my story which I did, only to be told that the Range is too old and they dont stand behind the warranty nor service anymore. They said beyond 5 years they dont do anything for the customer.I paid $8000 for this range back in 2005 and it has worked just great until this recent issue. If I had known that there was no service nor any parts for the fix I would have just dismantled the interior light. But why did they recommend the part I did purchase to begin with? Are they just trying to increase revenues by advising customers to buy parts that wont work? DO NOT BUY DACOR PRODUCTS UNLESS YOU WANT TO BE ON THE HOOK FOR REPAIRS AFTER ONLY 5 YEARS! This company has rude customer service agents and they do not stand behind their name!

We renovated our kitchen and as part of this had installed the new Dacor Modernist Fridge and Freezer columns at a VERY hefty price tag. We were going to get a subzero and changed our minds when we saw these products - the styling, design and function looked so much better than Sub-Zero, despite the higher price tag. Well, fast forward about 8 months and we dont have a functioning fridge. It stopped cooling out of nowhere. We had to throw everything away. After FINALLY getting a repair person to the house, they told me that it was because the fridge had run out of gas (freon or whatever the coolant is thats used). When asked how that happened they said they didnt know, but that they couldnt repair it as they needed a part from Dacor. A WEEK later, they finally got the part and came back to repair the fridge. 4-5 hours later it still was not repaired and they said they needed another part. Its been almost two weeks since then and the part has still not arrived. We had a BlueStar range installed when redoing the kitchen and when we had a problem with that, they overnighted the part, so that they could fix it right away. This is not the case here - the customer service has been absolutely horrendous and Ferguson Appliances (where I bought the fridge from) has been at their wits end with this (I cant say enough about how wonderful Ferguson has been to deal with). This has been a nightmare. Now the repair place wont even schedule a repair date because they dont want to lose the time again in case the part doesnt show up again... DO NOT BUY THIS FRIDGE. I should have known better not to buy a Samsung (yes, Samsung bought Dacor a few years ago and these products are glorified Samsung units).

Years ago I purchased the Dacor Double Oven over a Thermador because the Thermador had a ridiculously long pre-heat time. The Dacor has performed reasonably well as a oven particularly in convection-bake mode. But over time, components started failing and repair parts were hard to find, unavailable or ridiculously overpriced. I am an an engineer with DIY skills honed from years working with high tech food manufacturing equipment and controls including ovens. In recent years, I have needed to replace a relay board, the main control board, hinges two times, and most recently the hinge receptacles. I have also replaced an inner panel on a door assembly. Just think what such repairs would have cost for an average consumer. I understand the parts can fail, but Dacor has shown little regard for consumers in my opinion. They have done very little to maintain an inventory of repair parts. Basically their message is that the part is now obsolete and unavailable. Thats some answer when the price of a new double oven is multiple thousands. Recently, the hinges on my upper oven failed again. As they failed, their failure caused increased wear on the hinge receptacles. Soon the receptacles failed as well. I was able to find hinges at a ridiculously high price but the receptacles were unavailable anywhere. I contacted a several parts suppliers who told me that they had no idea when the parts would be available. Moreover at least two of the suppliers mentioned that they had a backlog of orders for the receptacles - one had a backlog of over thirty. Yikes!. At that point I contacted Dacor customer service and asked what could I do to get the part. Answer: The part is unavailable and we have no estimate on when it will be available. I tried to escalate my request and got nowhere. Finally after many hours of online searching, I found one set of the hinge receptacles at a price 4X last years price. Lastly as I replaced the receptacles today, I realized that the mounting screws only hold one portion of the U shaped mount. If the screws were longer, the receptacle would be less prone to twisting and wear. Be aware that Dacor was sold to Samsung a few years back. Based on my experience, I could never recommend Dacor. Caveat Emptor!

I am thrilled with this stove. I have always had a vertical double oven so this is a first for me. Really pretty in my kitchen. Almost like a piece of furniture. Can’t wait to start cooking!!

Replacement light for the oven - I could not find anyone that carries the halogen bulbs for my oven and called Dacor parts line. The bulbs come in a package of two. They were $79.95. I was told I should have called two months ago, that they were $29.95. So would I buy another Dacor Appliance? I think not.

We own 3 Dacor appliances, gas cooktop, microwave & built in oven. From the day of installation of wall oven there was a problem. Without going into detail suffice to say it was repaired 3 times within several months, under warranty. We were having issues with our microwave not working consistently, after several service visits, not under warranty, we now are told it will cost over $600 for the part. We are now looking for another brand of microwave instead of fixing the Dacor. On a side note the rings for our Dacor gas cooktop never come clean no matter how hard you try. The material used are definitely inferior. We have another property with all KitchenAid and have been happy with the performance. Our fridge & dishwasher are KitchenAid and I regret not getting the same brand for our other appliances. If I could give a minus star for Dacor I most certainly would do so.

We installed 2 Dacor wall ovens, a 5-burner cooktop, and a downdraft fan in 2000. The convection ovens bake perfectly and have performed without fail. After 7 to 8 years of daily use, we did have to replace the door hinge on the oven I use most often. We are in a rural area so the repairs are accomplished through Sears. The replacement parts arrived in a timely manner and the oven has worked perfectly since. The cooktop is easy to clean and the heat is even. The downdraft fan is effective and easy to clean. I would be confident to recommend Dacor products.

We remodeled our kitchen in 2002 and chose the Dacor 36 dual-fuel range. I was preparing a pork roast for a dinner party with the oven on Bake. The roast was just not coming up to temperature, though the display indicated that the oven was at the temperature I set. I wound up slicing the roast and cooking it on the griddle; my hungry guests were getting restless. Then I tracked the oven heat for an entire day with an oven thermometer. The oven would come up to temperature and then cool off. I sent these numbers to Dacor and asked customer service for an explanation. Believe it or not, the conversation was--Dacor: The temperature is going down because the fan is coming on. Youre not supposed to use the Bake setting, but only the Convection Bake or Pure Convection. Me: Why is the Bake button there, then? Dacor: Were taking it out in the next production run. (This hasnt happened. My sister-in-law bought a Dacor last year before I could warn her and the button is still there.) Also, after using the self-clean one time, I noticed a crack on the inside of the oven door, starting in the corner of the window. The inside of the window is now permanently spotted with baked-on grease. Now my oven does not work at all. The repairman says that the circuit board needs to be replaced, and if Im lucky, it will work for a couple of years. The repair will cost around $700 including labor. The repairman told me that some repairmen in our area will not even work on Dacors because there are so many problems. Im considering replacing the stove... a very expensive mistake. Beware of Dacor products.

I just had an appliance repair company come out to let me know what is wrong with my Dacor Stove door, since it wont close. He said the hinges are needing to be replaced. He said that he replaces these hinges on Dacor stoves ALL THE TIME and that the company really needs to file a recall on these hinges and/or reimburse consumers who have these installed. He said these should not go bad like they do. That this is poor manufacturing on Dacors part and they are not being held accountable. I agree 100%. It is going to cost me with labor and parts almost $ 400.00 to replace these hinges that should not go bad with the age of the stove. Thanks.

We purchased the modernist collections 48” range, refrigerator and freezer, oven and microwave combo and dishwasher with a kitchen remodel 9 months ago. We had one issue with the dishwasher which was resolved, then another when is stopped mid-cycle. Repairman came out and was told we needed a new panel. Found out it was back-ordered. Well, it’s now been FOUR month without a dishwasher. We have contacted customer service and asked for other options and were told there was nothing they could do! When following up we have left messages and had our calls not returned, as has our service company. I have waited on the phone 3 times 30 minutes to talk to someone, because they won’t call back. We’ve asked to talk to a supervisor, and was told our information would be forwarded... 2 days later, no call. This is by far the WORST service I have ever had for ANY type of product.

Weve had these appliances for 15 years. The cooktop has worked well. However, it could be improved with a lower lever for heating on its small burners, allowing it to simmer water rather than boil. The Dacor exhaust we purchased is one of those type that pop up out of the counter. It works but leaves much to be desired. When it runs, it pulls so much air the flame goes out on the burners. It is still not efficient at getting rid of cooking smells or smoke either, but that is simply a problem with all of this design so I cant fault Dacor. We have the biggest problem with the double oven. There are three main issues: 1) Whenever we run the self cleaning function, it pops the heat safety switch inside the oven housing so I need to take it apart to fix it. Hence we work to keep it clean so we never use the cleaning cycle. 2) The oven door gaskets prevent to door from closing and sealing all the way. The door tilts out app. ¾ because of this. We were told by the service guy who came to fix problem 1 above that this is the way the doors are(!). Our bottom one also tilts out but not as much. Ive dealt with this for 14 years! 3) We have to sand the burner electrodes on the cooktop to ensure they spark to light the burners at least 2-4 times per year. Not sure if that is normal or not.

We bought our house in 2010 and our Dacor stove was supposedly newer. When I went to clean it, I found loose screws in the bottom. Apparently, the convection element is loosing its screws and washers. Ive had this appliance fixed once already when the cooktop kept clicking. The black plastic around the controls cracked mysteriously. It takes 3 hours longer to cook a turkey than it should. This is a strange stove, which supposedly cost a lot. I wonder if a convection part missing two screws should be used?

We have a new (one year old) home with Dacor appliances. The microwave oven went on the blink the first month but was repaired by a factory approved repairman. Something to do with the computer. Now the double oven will not hold a temperature. We set the oven at 420 and it only goes to 360 even though the readout shows 420. We just decided to skip the repair process and bought a new Wolf oven. This is our second Dacor within the past two years and both have had the same problem. Dont waste your money.

The Dacor (model ER36SCH/NG) burners work, but the oven & the broiler burners will not. The circuit boards were replaced twice 2 times, under warranty, but still fail. I have to un-plug, or turn off then on the breaker to reset the circuit board. Dacor states that they are aware of defective boards, but are working on new replacement boards (no board yet). Its going on now, for over 6 months. Is there any news? I am very frustrated!

Updated on 06/14/2021: We placed a review about a month ago about a defective range. The company contacted us, took some information, but we have not heard from them since. It seems they just wanted an appearance of willingness to help but do not intend to help. After spending almost $4000 on a stove you would think it would last more than a few years before the motherboard malfunctioned. Dacor has provided no help. Very poor customer service and an extreme disappointment.Original Review: We bought our Dacor range for 3800$ in 2017. The self clean function did not work due to a defective locking mechanism. We had that repaired. Starting in 2019, the bake cycle was not heating up to set temperature. We followed recalibrate instructions. Then, the temperature went over the desired setting. I’ve tried adjusting baking times to deal with the problem. Convection bake started having temperatures above the set temperature.Several months ago we called for repair. The service technician tested the sensor and said it was fine. He stated that it was the motherboard which would cost $1200 to replace with parts and labor. That’s a lot of money to put into a high end stove that cost $3800 to begin with and is only 3 years old! We’ve had Frigidaire stoves that lasted 15+ years. This continues to be a problem. Unfortunately, we may have to replace this stove with Viking or Wolf. This is totally unacceptable considering the initial cost of the stove and the fact that Dacor markets their products to be long lasting and reliable. Never will I buy Dacor products again.

I am having issues with my Dacor oven and have tried to contact customer service since Monday 01/04/16. I was on hold for 27 mins and finally left my number for a callback. I have called every day and leave my number for a callback, no response. Today Thursday I sent a message and the response was that someone will call within 2 days. Great customer service. Buyer beware.

We remodeled our kitchen in the fall of 2009 and decided to purchase what we thought were higher end Dacor appliances (stove top, oven and microwave). Well, what a mistake that turned out to be. Considering the price we paid for the appliances, you would not expect problems from all 3. Perhaps a problem with 1 appliance, but problems with all 3 suggest a real quality problem. My first indication should have been when I called and asked how to change the green LED on the microwave to blue to match the nice blue LEDs on the oven mounted right below. I was told that someone else makes the microwave and Dacor just puts their name, and that I should just turn off the LED on the microwave. I dont know if that is true, but that is what I was told.Now when using the microwave/convection feature, the oven makes a noise (sounds like a fan motor) for the first 3-5 minutes then eventually quiets down. A daily reminder of the mistake we made purchasing Dacor. Then those nice blue LEDs on the oven started failing making it impossible to read the clock, timer or temp. Luckily, the oven still works; you just cannot read the LED any longer. This is a constant reminder of the mistake we made buying Dacor as we see the LED every time we walk into the kitchen.Finally, we have the solid surface electric cooktop. Although it works fine, the black paint on the metal trim around the stove top is wearing off. Now, we have some shiny metal and some black trim. This is just an annoyance and honestly, we probably would not have even complained about it. However, with the other problems we have had with Dacor, it just adds to our overall disappointment with Dacor. If I knew then what I know now, I would be a lot happier because I would have GE appliances and not these overpriced low quality Dacor appliances.

I bought a Dacor appliance package for a new custom home which costs over $30K+. Every single piece of appliance is defective. I am OK as long as Dacor can fix or address the issues but it takes them several visits, put the appliance out of order and fixing it does not happen any earlier than 8-10 Weeks. Imagine you living with a fridge, microwave, range and oven for 10+ weeks. The column freezer stops making ice. I call for service and tech informs the lever was jam and he fixed it. Wait 48 hours.After 48 hours still no ice. Another call and after a wait of 3 weeks another visit and diagnose need new part. Wait for part 4+ weeks and another 3+ weeks for replacement. Fridge does not cool and maintains temp 45 degree+. Service tech showed up 3 times and promised it is fixed. Have thrown out thousands of dollars worth food. To date I dont have it fixed. Waiting for a part, tech not available scheduling issues etc. To date I have been out of fridge (8/12/2021) 9 weeks from I made the first call. Currently I have a tech scheduled for 9/1/21.This is not the end. Microwave will run normally and wont heat the food. After several phone call and waiting they figured the door pin was not connecting properly and need parts to fix. After 10+ MONTHS it looks like it is fixed. The range control panel is hanging from underneath and no one seems to care to fix it. Every time I call they tell me its normal. I believe Dacor has not QA/QC in place prior to shipping the appliances to customer. Worst experience ever. If you need more details do not hesitate to call me on **. I hope you run away from Dacor. Dont even consider this option. I have a track of all phone call and email and timeline with Dacor service. I am planning to file a lawsuit and recoup some of the costs and losses.

I have own my range for about 2 years and for the most part it is used every day. I love the simmer burner and how strong the rest of the burners are. My food always cooks well both on the stove top and in the oven... I love this range.

The Discovery Model 30 electric wall oven - After 6 years, the oven failed. The fan motor went out and at the same time, we were advised by a very reputable appliance repair recommended by Dacor that we need to also replace the computer or brain. Total cost of repair: $1150 with a warranty of one year.

I spent a lot of money buying a Dacor double wall oven because it was supposed to be top of the line and dependable. Now, the circuit board needs to be replaced and the oven is just 5 years old! This seems absolutely ridiculous for an oven this young to have such a major problem! I am very upset about all the money I am going to have to spend to fix it. Ive never, ever had any oven problems with other brands like this in my life. We remodeled our kitchen and I thought I was getting something better and now I realize that this brand is not living up to my expectations at all! I am using an authorized Dacor repair company and they told me that they are seeing lots of problems with this brand. I do not recommend this oven to anyone.

There is not enough space to write about the problems with Dacor ovens. Just do not EVER buy any of their appliances. FOUR breakdowns, excessive cost to repair, cheaply made electronics, etc., makes me wish Id never heard of Dacor or Trial Appliances, who recommended them.

The enamel on the bottom of the top oven has blistered and the metal beneath is exposed. If the oven is heated, there is a chemical smell. This is such a dangerous situation that the ovens (double) are being removed as I write and will be replaced with a different and more reliable brand.

I bought a Dacor dual-fuel range in 2002 for my new house. Within 18 months, the control panel on the front had shorted, causing the stove to emit a continuous beeping. I got this repaired, and was advised that I should not use liquid cleaners on the stove! Two years later, the same thing happened again. Finally, about 4 years ago, another fault developed in the 3rd control panel, the circuit controlling the oven lights will not respond to touch, and the oven lights switch on and off continuously. Not prepared to pay for yet another control panel replacement, I switched off the power to the stove at the main fuse box. I have continued to use the gas cooktop only, lighting it with an ignition wand. The Dacor stove is only part-functional due to what is obviously a severe design fault in the front touch control panel, which causes the panel to short. I switch on the power to the unit twice a year to use the oven at Thanksgiving and Christmas for large roasts. This stove was a very expensive mistake. Luckily, I have a second (Wolf) oven in my kitchen, which I use instead for everyday cooking.

The oven temperatures fluctuate while baking. The company was at first responsive. They replaced the oven controller and the temperature sensor. This did not fix the problem. When I called and left messages, there was no call back or response. Very poor customer service.

We just purchased our home in March of this year. The previous homeowner purchased a Dacor oven; it is electric & propane. She purchased the appliance after a complete home renovation in 2008. They lived in the home. After 1 year, they moved out and had it on the market. We purchased the home in 2012. As soon as we moved in, we noticed the oven was not working. We called an appliance repairman - $564.00 service call and part for a new relay switch. It was great; the oven worked. Not even a day later, an F1 error. We called them back out thinking they must have done something incorrectly. They then said we needed a new control panel. We did not have an additional $400.00. We just moved, so he said you could still use the oven. We did. We would use it and flip the breaker off so we did not have to hear the annoying beeping sound. Then I came home and bam - no display, no oven. We called a different Dacor certified appliance guy thinking the first company was just taking us for a ride and it was their fault. $572.00 later, we got a new control panel, but guess what, the technician did not even make it to his truck before beep, beep, F1. He came back in and then said we needed to replace the display screen - an additional $217.00 with no labor charge. We told the man to shove it. I had every plan of taking the oven to our back tank and using it for target practice. But in good business practice, since this company already invested $572.00, we could not ask them to eat the money, so we allowed a third fix of the oven. While the technician was here, the oven made a horrible loud sound and shot out flames. He insisted maybe it was due to it sitting for a week without use. He left. I never noticed this flame before when the oven worked despite the F1 beeping. Now it’s hit and miss. Some days it will shoot out a flame once until it reaches 200+ degrees and then you can hear the fan kick in. Some days, twice, I have had it happen 3 times. If my children were to open the door during this event, I am sure they would be seriously burned. At first I was thinking maybe it is normal for this oven to shoot out flames during preheat mode since after $1300.00 repairs maybe it is just not functioning correctly. But if it were a normal function of the product, to me it would do it every time consistently and not three times, or two times on some occasions. I hate to admit this but I am almost fearful of using my oven. I currently have a pie to put in for dinner and I’m thinking its 3:09 pm; I could set the oven to preheat while I run to get my kids from school so if it decides to blow up, I am not home and that is pretty sad. The last repairman we had come out said in his personal opinion, he wouldn’t have repaired the oven, because they are known for issues, and he would have gone to Lowes and spent $300.00 on any off brand stove first. We have considered that, but this stove is extra-wide and the cabinetry is built around it. So for us to purchase an oven to slide right back in it would be another $1300.00-$2000.00. We have issues with the burners not always wanting to light. I almost caught on fire lighting one because it shot out flames when it decided to finally ignite. Sometimes it just clicks. Currently, I am down to two burners when just two days ago all six were working just fine. Over Thanksgiving, it took no kidding 1-hour to cook brown and serve rolls because the oven did not reach the set temperature. We stuck my husband’s bbq thermometer to see. It was 256 degrees, not the desired 350 degrees. Does this stove have warranty? We have no clue as the previous homeowner purchased the stove. She claims to have spent $5,000.00 on this stove or more during their purchase. We do not have warranty on our home so for each repair, it is out of pocket for us, and currently we really are thinking any knock off brand at Lowes would be a better product than a Dacor oven and less of a safety hazard for our family.

We had our range oven for less than a year and the front electric panel cracked, there is no stress to this area. I called the company and they admitted the entire panel was defaulty and had a recall. They did replace it. Within 5 months the new one cracked in the same place. This time they stated the unit was out of warranty. I told them the same type of recalled panel was installed. They said I could buy a new one. Ha! Since then many more cracks. I will never buy anything made with the Decor brand nor do I recommend them! Happy shopping.

Ive had this range for two years and am replacing the control panel for the second time. 1st time during product warranty and second time out of warranty. The range is beautiful but apparently the electronics are bad. And to add insult to injury Dacor doesnt stock replacements but has them assembled when needed. Estimated wait time for a new panel is 3 weeks; so no oven for 3 weeks and now not a lot of faith that the new board will be any better than the last one.

I purchased my Dacor Epicure Range 8 years ago when I remodeled my kitchen. My other appliances were made by GE and Bosch. Ive had to service my GE appliances a couple of times in the last 8 years, but it is the Dacor that has given me the most grief and it was the most expensive appliance purchased. It has never been reliable with regard to convection baking. Initially I thought it was my inexperience with a convection oven. I read everything I could get my hands on and kept trying...after talking with a friend who does quite a bit of baking I realized its not me, its my oven. Then the real problems started. First it was the broiler/ignitor, next it was the membrane in the keypad. Two months later it was the relay board and this time it was the broiler/ignitor....Again! Started calling Dacor when the relay board went out because at this point I had spent $1,000 on repairs....after I had paid $4,000 for the range itself. For the last two repairs Dacor has paid for the parts, while I paid for the service call and labor. This has reduced the cost of my last two repairs by about 50%, which is very helpful. However, Im still very disappointed in the product. I spend a good deal of time in my kitchen and do quite a bit of baking, cooking, and canning. I thought that if I spent more money and bought a high-end appliance, it would serve me well. At the rate that Im going, I will need to purchase another range, unless I want to keep throwing money into repairs on this one, which I dont. I will not ever purchase (or recommend) another Dacor product again.

I purchased all Dacor products. First Dishwasher went out, had purchased warranty. Came out 6 times to fix it, filed complaint with Better Business Bureau. Finally got dishwasher replaced with a Kitchen Aid. Thank God for the BBB. They help people. Then my stand alone range with 6 burners had one of the burners go bad, the appliance co. fixed it. Then the oven relay board went defective. Had to order part over $400.00, no warranty. Then wall oven Relay Board went out, 2016. Paid over $460.00.Less than 12 months later relay board went out again. They said Sorry, no warranty. Ordered part said it was $500.00 + to replace. The appliance repair tech ordered wrong relay board. They called me today and now said its going to cost $650.00, no warranty. Do not buy Decor products. They are horrible. I feel I am being ripped off by Dacor and feeling untrusting of the Appliance Co. I may need to file another complaint with Better Business Bureau. Buyers beware!

I purchased a Dacor Black Dual Fuel Range (RSD30B) in 2001 which was installed during a kitchen remodel. We moved back into the house on 12/24/01. We hardly ever use the oven because my husband barbeques every night. In less than 5 years, a piece of the plastic front control panel fell off. In early 2008 the self cleaning function broke (error F2). I called Dacor and they referred me to a repair service. It was going to cost almost $500 to repair so, given that we use the oven so little, I decided not to spend the money on an oven that was falling apart. Now within the last two years the plastic control panel is cracked across the front and more pieces are starting to fall off. Now the clock and the timer have stopped working. I called Dacor again today and was told that the seals and hinges on the oven are probably bad, which is contributing to the problem. The customer service person was rude and unhelpful. He said it was not unusual for a ten year old oven to break. He gave me contact information for a parts dealer and two repair services. I bought this oven believing it was a high quality and I expected them to stand behind their product. What can you do to help me?

October 2013 we had the Dacor model# EORD230SCH installed. It broke just in time for Thanksgiving! After several attempts of repairs, Dacor replaced this oven model# EORD230SCH with the next newer model at no cost. Not more than one month later the replacement oven doesnt work. Service is painfully slow. We had a 03 year warranty on the original purchase and the clock keeps ticking from the date of the initial installation. WE have asked for and been denied by Dacor, to reinstate the 03 year warranty once the unit is actually working. We bought this unit, spent extra money, thinking we were buying quality. So, two ovens in less than one year, doesnt equate to a quality product to me. Keep getting the standard answer about the warranty - no added time will be assigned.

I replaced my Thermador Wall ovens with Dacor because the size and I would have to do less retro-fitting of my cabinetry, this was a grave mistake. Here are the issues with Dacor.1. The high heat sensor trips and you need to call a service professional to have it reset. This gets very expensive. I have tripped mine three times, once baking a cake at 350 degrees, once during self-cleaning and another during normal cooking. The Dacor Service Help said this was a common problem because the heat sensor is located near to the touch panel.2. The oven vents from the bottom of the unit into the room heating my kitchen.3. The glass window does not seal so I have stains in-between the panes of glass. Not very attractive to stare at large drip stains.4. It takes an exceptionally long time to pre-heat oven and convection mode even longer.5. The temperature cycles through and does not maintain its cooking temperature causing underdone results and longer cooking times. This is especially challenging when cooking roasts and large turkeys because they may take up to an hour longer than expected.Overall, I do not recommend this product.

Our 30in Dacor double ovens are approximately 12 years old. I feel they operate adequately. However, not better than our much lower end appliances we previously owned. My main complaint is the self cleaning function. My old ovens self cleaning worked much better! With our Dacor ovens one must take out the racks and clean them by hand. This is very difficult and time consuming. I used the 3 hr option to clean my oven that was moderately dirty, mainly from cooking a prime rib over the holidays. After the 3 hr cleaning the oven was still very dirty with splatters and grease. Im now cleaning my oven again with a second 3 hr cleaning cycle. I know at the end of this second cycle I will need to do a lot more cleaning by hand! I hope Dacor has improved their inadequate self cleaning feature. If it hasnt been improved, I really cant recommend Dacor ovens.

I was very upset when I tried to get service on my Dacor range. I made a complaint to ConsumerAffairs.com and was subsequently contacted by James ** of Dacor Customer Service. He offered a telephone number to support a local appliance repairman and arranged for me to get my parts at a special pricing. This worked out great and my range is now fixed. I am a happy Dacor Range owner now. It was just too bad that I had to make a complaint on the internet before I got help. I hope this incident will encourage increased cooperation from Dacor in the future.

I was and, I repeat, was a loyal Dacor customer. I gutted and rebuilt a kitchen 9 years ago and purchased a Dacor stovetop, oven and microwave. I remodeled my new house 5 years ago and again purchased Dacor stovetop, oven and microwave. Consumer reports provided favorable reviews of the appliances I purchased below.First red alert: The oven Model MORS130S and Microwave Model DCM 24S LED did not match. The microwave was green; oven was blue. The brochure was in black and white so there was no way of knowing that aesthetically they were a mismatch ... it was very sloppy(!) and very deceptive by Dacor. I mean when I waited weeks for my appliance order and the oven is already installed with a big fat ugly LED screen, what was I supposed to do, yank it out and start all over again? This was disappointing!Next, I was simmering chili on the stovetop (5 burner, gas) and, lo and behold, 18 flames started exiting through the turn knobs resulting in a meltdown. The gas was leaking through the tubes underneath the stovetop. I just happened to check the chili while I was gardening to watch the house almost burn down and btw, it was difficult to put out the flames because the natural gas was leaking under the unit. Seriously! I called customer service and they got hopping right out to fix the issue. This scared the heck out of me. It is negligent to have a product like that on the market.After about 13 months into the life of the Model MORS130S oven, the touch panel failed emitting a CO1 error message. I was told it was $140 to fix it and that the panel was defective, great quality there, Dacor. And the added joy to the CO1 error message is that the unit beeps intermittently all day and all night long unless the power to the oven is killed. Joy... now another issue - Model MORS130S oven LED lights are burning out. Seriously, what else will there be? Now its $175 for LED panel and another $100 to install by an authorized Dacor service man.So I called Dacor back again today because the LED light out was annoying me. They offered nothing. To be fair, my appliances are out of warranty but seriously, Dacor nearly burned my house down. They should be winning me back as a customer if they really cared about their customers and having long term repeat business. Never again, Dacor, never!

I remodeled my kitchen about four years ago with all Dacor appliances. It was the biggest mistake I have ever made. I have since replaced the refrigerator after only two years. After spending over $1000 in repair calls and parts, I purchased a new refrigerator as the freezer motor went out and had water all over my floor countless times even after new parts were installed. The ovens also have been replaced (12 months ago) as the lower heating element went out and had the upper and lower ovens go out with panel failures. I was so stupid to install the 30-inch dishwasher, as well. It also went out after 18 months with a motherboard failure. The upper rack glider also fell apart. Having the 30- inch dishwasher, I would have had to have a carpenter come in and make adjustments to my new cabinets. So I found another 30-inch Dacor dishwasher at an appliance store in Memphis, had it shipped to me and installed. It has been 10 months and I am now having the same problem I had with the previous Dacor dishwasher. It never ends! With the only option left but to have the cabinet remodeled, I will be purchasing a third dishwasher 10 months later. The only good that came out of this is the cooktop is still working (as of this date). All I can say is, if it says Dacor, dont purchase the product! This company shouldnt even be in business! What is even more pathetic is, when you call the Customer Service number, their representatives have such a I could care less attitude. It is a waste of time to even attempt to seek a solution to your problem. I guess they feel that since they have your money now, its the consumers problem, not theirs.GE Profile products are far superior and a lot less money. It goes to show an expensive price tag doesnt mean the product is superior.

I have owned a Dacor dual fuel 6-burner range for several years. I paid approximately $5,000 for the product. It has proven to be totally unsatisfactory. The gas burners click and make noise whenever you try to turn the burners down to a low temperature. The cook top is very hard to clean. The range is a constant problem. It smells bad, does not heat up promptly, and the broiler feature is always a problem. A gas oven is supposed to heat to and keep a constant temperature - the Dacor does not. The broiler will not cook food evenly or well. The door to the oven will not close properly and is constantly partially open. The hinges do not seem to work properly.Most importantly, I have tried on many occasions to get Dacor to do something about the defective product. They have been totally non-responsive. When I did finally get somebody to come and look at it, they spent about 2 hours cleaning it, accused me of using the wrong cleaner on the cooktop, and presented me with a bill for $800. I asked if they would just give me my money back and take the defective product with them. DONT BUY DACOR.

Dacor range - After I posted my comments on August 8th, I was contacted by Dacor customer service immediately and the new part was sent to me free of charge. I do have to pay the labor, but the part was what was expensive before. They did give me an explanation as to why this was happening - the hinges on the door wear out and the door doesnt shut properly so that heat escapes. Should this be happening with a stove that was this expensive? I dont think so, but I am happy with the customer service I received from Dacor this time.

I purchased my 30 range and was so excited! Well no longer. First the wrong range was delivered. I had to wait another three weeks for the correct one. My oven can not cook at all. Temp fluctuates by 100 degrees. Going on my third service call and still not working. It very unfair, I have to take time off work to wait for repair person, then nothing is fixed. I wish I could return this lemon. But after reading other reviews I am not alone. Why is this company not accountable for ripping hard working people off. I love cooking. Its my passion. My Kenmore Elite was half the price and far more superior.

I have had nothing but trouble with a wall oven I bought in 2010. Basically just bad electronics. I finally replaced the oven in 2014 and had to get another Dacor to fit the opening. The new unit still does not heat evenly and is consistently off by about 50 degrees. Customer service is not helpful at all. Local repair shops cant really fix issues. Terrible company. Cant figure out how they stay in business.

We purchased a Dacor gas range in 2005 for $2000. In a short time the plastic trim around the knobs cracked, and the glass in the oven door had not maintained its seal. I contacted Dacor several times and was told to take a picture and send it to them, then they could decide a course of action. The course of action was that I would pay for materials and labor. I decided not to do that, and eventually I will replace the range with another brand, never a Dacor!

48 in. Range - Wish I had read reviews first would NEVER have purchased Dacor. Paid almost 11,000.00 for a range so many issues they replaced it. New range came with 7 defects. It has been over a month and nothing has been done about it. Everyone keeps passing the buck and I am sitting with an high end expensive product and no help from Dacor. I am being very patient but also very frustrated at this point.

I have a Dacor 27 inch wall (model EOR) oven which I bought 2 years ago, along with a micro and a warming drawer. Since then, the control panel has been replaced twice. Both times because, after using the timer mode, the beeper would come on at all hours of the day and night. In both instances, I had to cut the power to the oven until the replacement part arrived. I am presently waiting for the third panel to arrive. Today I needed to bake something, so I turned the power to the oven back on. Now it will only function at 350 degrees and only in the bake mode. No other numbers can be put in and nothing happens when I select convection. So far Dacor has absorbed the cost of the parts and repairs, but that does not mitigate the hassle of having to wait upwards of 2 months for a part each time this happens.

This week Dacor installed my 2nd replacement gas range. I remodeled my kitchen 3 years ago and chose Dacor because I had a great experience with their appliances in the past, had their oven and stove in my kitchen for 15+ years and never had a problem. With the first new range, the oven started to automatically shut off due to excess heat escape, so the safety feature would kick in and shut the system down, in addition the knobs would become very hot even when the over was used briefly, 12-15 minutes. I was very impressed and happy with the customer service through Dacor, they immediately gave me a brand new over. Exactly another year, the new oven had the same problem, door begins to not hinge properly and heat begins escape, knobs get dangerously hot.This week Dacor very kindly, replaced my appliance with the new Dacor Renaissance 36. I used the oven for 12 minutes on 400 and the entire exterior is dangerously hot. I do not have any children, however, if I did I would be terrified that they could seriously injure themselves. The exterior of an oven should not become hot like this. Has anyone else had this issue with Dacor? I feel they have been very responsive with regards to customer service however I want an appliance that is safe.

Have had an on-going issue trying to replace an oven door....since early December 2020. Have gotten a continuous run around regarding status of new door and shipment of same. Friendly Customer Service Reps do nothing to solve this issue. The oven door is designed not to be repairable or user friendly. Poor support and steady excuses have created another DIS-SATISFIED CUSTOMER!! AVOID DACOR!!

Very pleased to say Dacor replaced our oven with a new one! I havent thoroughly tested it all out yet, as it was replaced the day before we left for a trip. But so far the top oven seems to be working properly. Need to use the bottom oven yet to check it is working properly.

The functions are useful and so far everything works the way it supposed to. No real complaints. Convection and baking features are really useful when it is a small thing to start an oven. Easy to operate. Everyday cleaning is easy as well.

The electronics on the first two induction burners failed within six months which was covered under warranty. The second two went three weeks after the warranty and we had to argue with Dacor to cover them otherwise it is a $1400 repair job. From day one whenever you open the oven door the controls and heat shut off. Sometimes it turns back on when you close the door. As for the downdraft, it worked fine until 10 weeks ago when while closing, the cover lip hit a wooden spoon that had been lying flat near the edge. There is no safety feature and the motor continued to try and close the fan. The unit would not respond and would not re-open. The spoon had to be broken to get it out. If this was a childs finger you would have had to call 911. We now have a repair bill of over $350 and are still waiting for 2 months for Dacor to send a part. We will never buy this brand again.

Epicure Range, wall oven, microwave and fridge - When remodeling our kitchen in 2010, an appliance salesperson gave us a good deal on the entire set. We spent $20k on the Dacor appliances. BIG MISTAKE! Do not ever buy anything Dacor. We have issues with every single one. Where do I start? The ovens have gone out three times now and I have had to replace the main panel, now it will not heat at all. The refrigerator 42 built-in is a big piece of crap! We have had it serviced 4-times for everything. The entire fridge freezes over due to a design flaw. The fan in the freezer completely ices over. The ice door broke. The crushed ice broke. The plastic door for the butter broke. The shelves broke.The microwave has had issues and has had to be fixed. The oven temps were wrong. Fixed those myself thanks to YouTube. When talking to the service guy he said that these are cheap appliances with the Dacor badge, so you have to spend big bucks to buy them and big bucks to repair! Do yourself a favor and if you are thinking of Dacor run! I contacted Dacor and they are even worse to deal with. They did not care that their appliances are very unreliable. Never received a return call, email, or even a letter.

I purchased this upgrade to my kitchen renovation. The stainless steel stove has a great look, but that is all it has. This is my third repair (with much difficulty). The same problem - the bake ignitor goes bad and sends gas smells throughout the kitchen. On Christmas day, after preheating the oven, I opened the oven door and the inside was one large flame. The heat was intense and my right arm got hot from the heat. I immediately closed the oven and cancelled the bake setting. When I called Dacor the following morning, I thought I was talking with a robot. No emotions, no sense of caring. They must be programmed. I got no satisfaction. I said, Do you understand? My stove went on fire and on Christmas day. My family was not sure if they should leave my house. I am extremely disappointed with Dacor.

My stove is 3 years old and I have had to change the LED lights on the burners 5 times. One of the burners warped and was changed. The computer went after 2 years, now I have a gas leak in the burner hose. I have bought the extended warranty. I would not recommend this stove if you like to cook. Just make it look pretty in the kitchen!

We got a U43 relay error on our Dacor oven of 4 years. When we finally add up the cost to replace the part, it will exceed $500 and Dacors only response is, Sorry, it is out of warranty. Of course I do not understand why a relay board on an oven would short out after a few years. Not happy and would not recommend the manufacturer.

I completed a 7-month total remodel of our kitchen and family room, which were connected in November 2007. The kitchen remodel cost $18,000 for various Dacor appliances including the Millenia series of wall oven MOV130S; warming drawer MWDV30; and 42 island hood DHI42130. The remaining includes the huge 30 Epicure dishwasher ED30SCP, 36 cooktop EG366SCH, and beverage center EF24LBCSS. All have the beautiful copper accent package and make for highly attractive appliances. We constantly receive accolades for them. If only they werent absolute garbage functionally and reliability-wise. Others have remarked how the ignitors on the cooktop continually spark, even after the light off. After contacting Dacor and waiting 2 weeks for the repair, for which Dacor sent the wrong part and caused another 2-week delay, the repairman had to rip off the front accent lip of the cooktop to reach the base which significantly dented the front lip. The ignitor worked like a champ for 2 days, then click, click, click - constant ignitions. So I cleaned around the ignitor tip with 409, dried it and it worked flawlessly. Thanks Dacor for your own product ignorance and my now dented cooktop. It has worked well since and is a sound product, so far. If only my luck held out.Next, the wall oven. Very beautiful and my control panel has held out (fingers faithlessly crossed). The oven isnt calibrated though, so follow cooking directions at your own risk. This oven will burn your food if you set the temp and timer to the recommended settings. I have to take off 25-50 degrees and 5-10 minutes of requested cook time or I will smoke any meal. After 2 years of use, I decided to use the cleaning cycle - following the directions to the letter. Forty five minutes into the cycle and kaboo! The front window shattered. Dacor says $700+ for glass replacement; I say send me the part and Ill do it. I got the discounted part for $68; spent 3 hours cleaning and reassembling with care; and the window has held, but I havent tried the cleaning cycle since. Why roll the dice again?Ah, now my fave garbage Dacor appliance - the interminable dishwasher. Truly engineered by the diabolical. I just completed my fourth major repair after 5 years of use. First, the drain valve failed after a few months of use causing flood and was replaced under warranty. Then the door seal failed (more flooding) and was also repaired and replaced under warranty. The dishwasher stinks, by the way, as the unit cannot evaporate effectively during drying cycle due to ridiculously poor rear venting design. So I have to leave the door wide open for hours after use to facilitate drying and stench reduction. The control panel/circuit board has fried twice now in the last 3 years - it just starts erratically beeping and refuses to take input, even with a power reset. Both technicians stated the design and quality of the board is third world, which likely is exactly where Dacor outsourced the garbage.The island hood and warming drawer have worked well, and the beverage center has been reliable but maddeningly causes back left cans of soda to freeze and explode occasionally; even with the set temperature raised to now 45 degrees. Fun to clean up after coming home from a long trip. My expectations are so laughingly low now for these Dacor products that I dont bat an eye with the frozen soda muck this fridge occasionally produces. Customer service though has been helpful and thankfully, American. They have replaced both circuit boards for free well out of warranty. I have only appreciation and great sympathy for the customer service folks who Ive spoken with. I love my kitchen, but hate the appliances in it. Never again Dacor. Never again.

I purchased Dacor Brand cooktop, oven, microwave and dishwasher. The dishwasher quit working after four weeks. Price tag for the dishwasher 2,800. Three weeks later Pacific Sales in Corona will not take the dishwasher back and replace with a new one. Dacor is struggling to provide a service tech in my area to look at the machine and honor the warranty. In the mean time I am shelling out money for Dawn dishwashing liquid and washing the dishes by hand. Complete JOKE. If you want a brand that will not stand behind their product... purchase Dacor. Want a salesperson who will talk up a brand but the Store washes their hands of the transaction after payment, shop Pacific Sales in Corona Ca.

In 2013 we remodel our kitchen. I need a 30" stove and Dacor seem the right fit. I had problem with the igniter burning on that stove and some metal warp as well. They replaced the stove in 2015. I smell gas every time I turn oven on. Last Thanksgiving 2019 the stove stop working. I was told the igniter had burned out and had it replaced. I had repairman come twice because of smell and end January 2020 the stove stop working again. The repairman told me that a jet burner assembly was never installed this is why I smell gas after it is turn on. ** They said they will order the part. It's back order So I contact Dacor. First they told me it's back order then give me a supplier. If it was never installed in the unit shouldn't Dacor take care of it and soon.

We have a Dacor gas range RSD30R that we bought to upgrade our kitchen in 2002. We have had several issues with the range to date. The first issue we had with the range was the auto lock for the oven cleaning cycle that failed in 2007. It was not covered under warranty and cost $88. The second item to fail were the oven door springs. They also failed in 2007 and covered under warranty. They failed again in 2017 and had to be replaced for a second time. The springs are too weak to hold the weight of the heavy door. $68-$78 for the springs. The springs could easily be changed out as the brackets are still good but they only come as complete units. The last item to fail were the ignitors. Only one ignitor failed out of the four but as the spark module ignites all burners every time any one is turned on, premature failure could be expected as all ignitors light every time. This time the part is no longer available from Dacor. Dacor does not support any products they build after 7-8 years. Parts will no longer be available. I would not recommend Dacor Appliances to anyone as the manufacturer does not support their own products very long. I purchased Dacor to buy American and I regret it now. In contrast every product that Miele made even 20+ years ago, parts are still available directly from Miele and other suppliers as well.

Dacor representative has been helpful in responding to my complaint and has sent new oven racks which I greatly appreciate. I was able to send them pictures of the damaged racks. I want to clarify that the warranty that was sold to me by an upscale appliance center was NOT a Dacor extended warranty and I believe that this caused my issues to slip thru the cracks. Nothing can be done about the interior that seems to have a film of sorts on it, short of replacing, but I am grateful that Dacor customer service went out of the way to correct the problem with the racks.

I built my home in 2003 and installed a Dacor 30 wall oven. After several years of poor performance, we started to get an error message. Dacor suggested replacing a board for $300. That didnt work so they had me replace another $300 board. That didnt work so they told me I needed a new front panel and it would run about $1,000. That board is on back order and they dont have a replacement date. Thinking that its bad business to sink $1600 into a troubled product that has terrible reviews on the internet. We found out that once you go with Dacor, you need to stay with Dacor due to an unusual, nonstandard size.Thinking that Dacor has improved their product we ordered a brand new $3,000 Dacor RO130 30 wall oven. It arrived promptly and I removed the defective $3,000 oven and put in the brand new $3,000 Dacor RO130 oven. What I got was a dead brick. The Dacor customer service has been awful, and will not allow me to talk to anyone in their technical side. The oven is getting power. Dacor customer service wouldnt help me unless I could prove that the unit was getting power. So I had to get an electrician in to prove that I had properly wired the 4 cords that came off the original defective Dacor wall oven. Get service help? No chance. I live 100 miles from Seattle and no one wants to work on Dacor. So here I sit with a $3,000 brick. No service and Dacor has no clue on how they will service this wonderful $3,000 RO130 30 wall oven that is an out of box failure. I dont see how a company that has this bad of a product, two generations of defective ovens, bad customer service, reluctance from the repair community to work on their products will be in business much longer. If you are considering Dacor appliances, consider the problems that I am having. The nonstandard size of their ovens will lock you into future purchases to replace their products that dont last 10 years.

Previously, I submitted a complaint here and I would now like to amend it. The problem(s) that I experienced with my 8 years old Dacor 30-inch wall oven was what I described in my earlier post (July 9, 2012). But after posting here, I was contacted by a Dacor representative not once, but several follow-ups to ensure that the problem was resolved to my satisfaction. It was and Im now very impressed with Dacors customer support. To be fair, I should have contacted Dacor with my problem before blasting their product here.It has been a good oven for 8 years and given their support that Ive recently experienced, Id be more inclined to purchase Dacor products in the future as it appears theyre willing to stand behind what they sell. Im really glad this issue was resolved because I was about to throw in the towel and buy something else, but couldnt find anything else that looked near as good as my Dacor and had glowing product performance reviews.

I have been very disappointed in the reliability of our Dacor refrigerator, model EF42BDCBSS, purchased in 2007. The first circuit board went out in 2008 within 6 months of the initial purchase. A replacement part could not be located. It was still under warranty so they replaced the whole unit. In 2010, we had to have another repair to regulate the temperature of the freezer. Last week (October 2012), the circuit board went out again! Even though the unit itself is less than five years old, it is no longer under warranty. Dacor goes by the original installation date. I contacted Dacor and spoke with LS who basically stated that all they could offer was a discount on the part. This repair is costing us over $650, not including the loss of food. We paid to have the part second day. When we called back the next day to get a tracking number for the shipment of the part, we were told by another representative that the part had not shipped because it was out of stock in the default warehouse. He was able to locate it in another warehouse and get it shipped the same day. I called LS back and she stated that she never promised when it would ship, but when it did, it would go second day. I would not expect this type of repair cost and attitude on a refrigerator that was over $9,000 when new. Now, I am concerned with the liability of our range and microwave, which are of the same Dacor brand. The main reason I took the time to write this email is to make retailers aware of the situation and ask that you seriously look at the reputation of the Dacor appliance line and decide if you really want to promote this product to your customers. Dacor could care less about their customers and/or reputation.

I wish I had read all these reviews of Dacor products before being duped into paying for a high end wall oven. As many others have mentioned, the electronic panel design is faulty. I paid $1000 to have it replaced once. Now it is broken again and the alarm beeps constantly. The reply from their service rep was that they havent had any recalls of this product (in other words, no ones house has burned down yet). He also admits that he wouldnt buy a Dacor oven unless he had money to burn. Well, my money has already burned and so have I.

Our dacor appliances are 8 years old. Four or five times a year we need to have the technician to come by to fix something in our kitchen, dishwasher, built in fan for our stove top or refrigerator. These items are high price items-- should not have so many problems.

I remodeled a kitchen in a high end house and so wanted nice appliances. I had KitchenAid (which Id had a lot of issues with) for about 16 years. (Since I built the house - the fridge was rebuilt 3 times.) While looking for which appliances to use we were at an open house and a chef was cooking and giving a talk on the Dacor ovens in it. So... I reviewed a lot, liked what I read, and chose Dacor. I love them, the cook quality, the features, all of it. BUT my double oven had issues from the start. An annoyance at first with the built in Android but I didnt complain a lot. Move forward 1.5 years and the Android tablet built into it would freeze and not restart without throwing a jumper on fuse box. I called Dacor and they gave me a number of options, disable the Android because of a known issue and get $500 back, or - return the oven for full credit and theyd pay to have it removed (1.5 years later... cmon thats pretty awesome), or - pay $500 and move to the newest higher end model with steam cooking. Wow, talk about stand by your product! Ive never seen this before with an appliance manufacturer/vendor. Certainly wasnt my experience with KitchenAid. Anyway Im an advocate even though I had a problem and thought they deserved credit here.

Dacor customer service contacted me and worked with me and the appliance repair company to get the proper parts to fix the oven. Everything is fine! We once again really love our Dacor wall oven.

Purchased a Dacor Epicure ER36DSCH/NG RANGE and oven in 2007. Sad story, it never worked properly since day 1. Initially a gas burner did not light, they came and repaired it. Subsequently the door lock failed in the lock position - had that repaired. The door lock failed the next year again, this time thanksgiving, ruined the dinner. They fixed it but the following year the lower burner element failed at Thanksgiving. All my relatives know not to purchase a Dacor product. Problem is I am stuck with this boat anchor. The oven door motor has failed 3 more times and thankfully the service man showed me how to change it. Today we tried to bake some apple pies and found the oven temperature set at 450 was only 350 (bought an oven thermometer). This explains why it always takes so long to bake things. A complete piece of **, never ever buy one.

We purchased this high end Dacor range (Dacor Renaissance ER30G) new in 2011 from the Appliance Loft here in Cincinnati. It was dropped off and installed and would not operate right out of the box. A repair was made and everything worked (unless you count the indicator lights on the knobs, they all went out after approx 14 months). This past November the oven went dead. A1 appliance came out: Determined new control board needed, ordered and installed. Thanksgiving Day, oven dead. A1 comes back, reset the High Temp Fuse. Oven dead 4 days later, A1 returns with a new HTF. Dec 22, Oven dead. As soon as The holiday is over we will call another repair shop and start looking at replacing this unreliable piece of eye candy. Open comment to Dacors design engineers, quality control engineers and management. You should be totally ashamed about this product youve designed. You are supposed to represent the best in American design and quality and this falls below that of low end appliances out of China. See you in small claims court.

Worst oven Ive ever purchased by far. Pay big bucks and get junk. About 2 times per month, the oven will not heat up. I cant count the amount of wasted food and dinners out, because it does not seem to ignite, only warm up to about 100 degrees. I contact the appliance repair company and it works when they come out, so they dont do anything. I will never, ever buy another appliance from this brand.

This is the second time I have purchased these appliances and unfortunately each one has been a great disappointment. I have spent enough in repair bills to almost purchase a warming drawer. Each one shuts down when the self clean button is turned on, and then I have to call a repairman out to recalibrate the oven to work each time I try to use the self clean. I was told by the last repairman that the life of the oven is greatly shortened if you the self clean mode. If this is the case, either fix it or take out this mode. After I had the oven about a year the oven door glass blew out, and this had to be replaced. The temperature in the oven is very unreliable in different areas of the oven and browns more on one side than the other... For the high end cost of these ovens, I would just as soon have a basic oven that works and does not go out every few months. What a waste of money I consider Dacor to be, and will never recommend it to anyone I know. I am in the personal shopping business and have my own company, but will tell my clients to be very aware of the high cost/low performance of Dacor products... On a scale of 1 to 10, Dacor gets a 1.

We purchased a DACOR double wall oven (MOH2275) in April 2012. We are waiting for service to arrive for the fourth time since we purchased the oven. I find this unacceptable. We have had 2 other ovens in the last 30 years and they did not need any service. In general I have found appliances to be of such reliability that I dont get extended warranties. DACOR gave a 3 year warranty on this oven and now I know why. Hopefully this service will fix it for a long period of time.On the positive side, the oven really works well. It is so well insulated that we feel very little heat coming off it. One serious flaw its overall operation is the reheating of the oven. If I bake something at 350 degrees and then want to reset the over to 450 degrees, the oven does not go into preheat mode and does not let you know when you reach the required temperature. I am hopeful this will last awhile and not have to be replaced for what we paid for it.

In 2008, I purchased my dream home and had the opportunity to build my kitchen from scratch. At the time, I shopped Viking, Sub-Zero, Wolf, and Dacor. I made an appointment to tour the Dacor showroom and was blown away by the aesthetics and advertised performance of their line. I made the decision to fill my kitchen with Dacor products: dishwasher (ED24SCH), dual range (ER48DSCH), range hood (EH4818SCH), fridge, and microwave (DMT2420). To date, the fridge is the only appliance that has not malfunctioned. Within the first month, the microwave blew a fuse (covered by warranty). Within the first 6 months, the dishwashers motherboard blew (also covered by warranty).Since the 1-year warranties have expired, the range hoods electrical unit malfunctioned and ceased working properly ($400-plus in repair). The motherboard on the dishwasher has gone out twice ($1200-plus). The dishwasher rack has completely rusted and the wheels have fallen off ($800 to replace). The lights on my oven dial is out and the glass bottom inside the oven that covers the heating element has cracked (nothing has been spilled or dropped). In fact, I only use that side for Thanksgiving. I am extremely bummed (to say the least) and I feel that the products that I was sold do not live up to the quality level that they advertise. Additionally, the replacement parts are obscenely expensive, and at this time it makes more sense to replace the units rather than dump more money into a pit.

I, too, purchased a 30 Heritage gas range in Nov 2018. The first time I ran the cleaning cycle (2 weeks ago), the oven heating went out. After time consuming attempts to reach the warranty dept, finally got a call back. Sent the required information and was told the warranty servicer would contact me within 48 hours. After not receiving such call, I reached out via email again to Dacor and was told to contact the servicer directly. Well, I just did that, and was told they refuse to service me because DACOR IS NOT PAYING THEM! How is that for a luxury appliance company making millions off of its customers and not paying its service companies? A very clear breach of contract since my warranty is active until November 2021. I have never in my life had such an experience, with the LG, KitchenAid ranges I have owned. Never even have needed one ounce of service in their life. So now I await a response from posts on Dacor FB page and voicemail I left, hoping for service. What a colossal waste of money. Buyer beware!