About a month ago then again 2 weeks ago, I would hear a beep (not while I was cooking) from the stove. I went over and all elements had turned themselves on at HIGH. The only way I could turn them off is to repeatedly push and hold the child safety button. Very scary! If I had left a pot or pan on the range top, who knows what would have happened. It did it occasionally with 1 burner twice more. Yesterday, the range top started cycling every 90 seconds, on then off, then on, then off. I shut it off at the circuit breaker twice thinking this is a way to reset electronics sometimes. Once for 2 minutes then again overnight.I tried cooking on it this morning: on and off and on and off again. It is shut off at the circuit breaker awaiting repairs. I am a renter so am spared the repair bill but not being able to cook (of course it happened on Easter weekend!!) is a major pain. It is 10 years old this week the landlord told me, but I used to cook on a stove that was 60 years old and it worked like a champ.

The electronics on the first two induction burners failed within six months which was covered under warranty. The second two went three weeks after the warranty and we had to argue with Dacor to cover them otherwise it is a $1400 repair job. From day one whenever you open the oven door the controls and heat shut off. Sometimes it turns back on when you close the door. As for the downdraft, it worked fine until 10 weeks ago when while closing, the cover lip hit a wooden spoon that had been lying flat near the edge. There is no safety feature and the motor continued to try and close the fan. The unit would not respond and would not re-open. The spoon had to be broken to get it out. If this was a childs finger you would have had to call 911. We now have a repair bill of over $350 and are still waiting for 2 months for Dacor to send a part. We will never buy this brand again.

Motherboard on my favor wall oven has been replaced twice. Repairman said not use the self-cleaning feature as that will cause too high of heat and melt the components. Seriously, Dacor? We spend this kind of money and have these type of repair issues constantly. Just glad I finally was told what might help resolve this - I’m ready for a new oven because of all these problems.

I wish we had seen these reviews before we spent 6k on an oven and cooktop. Ordered cooktop and oven in November. Custom color over to match cabinets, still have not received oven (were at the 8 week maximum wait time already). Cooktop appeared fine when we received, but when we went to install, noticed something rattling inside. Looking through vent, noticed several broken interior pieces moving around. Contacted Dacor 3 weeks ago for a replacement or repair, and still nothing. They made us go through dealer, and last week told dealer we refused service. Ridiculous! Now they are telling dealer they cant find a servicer nearby. Am considering declining payment through credit card company for their lack of follow through and service, and let them come get their unit.

Weve had these appliances for 15 years. The cooktop has worked well. However, it could be improved with a lower lever for heating on its small burners, allowing it to simmer water rather than boil. The Dacor exhaust we purchased is one of those type that pop up out of the counter. It works but leaves much to be desired. When it runs, it pulls so much air the flame goes out on the burners. It is still not efficient at getting rid of cooking smells or smoke either, but that is simply a problem with all of this design so I cant fault Dacor. We have the biggest problem with the double oven. There are three main issues: 1) Whenever we run the self cleaning function, it pops the heat safety switch inside the oven housing so I need to take it apart to fix it. Hence we work to keep it clean so we never use the cleaning cycle. 2) The oven door gaskets prevent to door from closing and sealing all the way. The door tilts out app. ¾ because of this. We were told by the service guy who came to fix problem 1 above that this is the way the doors are(!). Our bottom one also tilts out but not as much. Ive dealt with this for 14 years! 3) We have to sand the burner electrodes on the cooktop to ensure they spark to light the burners at least 2-4 times per year. Not sure if that is normal or not.

We remodeled our kitchen in 2001 and bought a Dacor Epicure 30 dual fuel range. The gas cooktop has never been a problem, unlike the oven which has been a problem from the first week with unpredictable temperature variations. Multiple holiday meals have seen the extended family waiting for dinner for two hours because the oven decided to be cool that day. The advice from Dacor: preheat your oven for several hours before you need it or my favorite from a repairman: you must be slamming your oven door. Not helpful. Several expensive repairs later (over $2100) and one fire in the oven now it wont turn on at all. We are going to try one last time to repair it and then we are done. I do not recommend Dacor to anyone - too expensive to have such terrible quality and service.

Warning! Do not buy Dacor appliances! We have had our appliances for three years now and all of them have had something wrong with them. Oven circuit panel went and had to be replaced! Dishwasher arm and seal broke and dishwasher leaks! Refrigerator freezer compressor went! Hood range switch broke and had to be replaced! Dacor is the worst appliances I have ever bought! Buyer beware!

The ovens needs a new latch kit and a mew control panel every year. It has been repaired 15 times. So many issues but those are the most consistent problem areas. Dacor should have replaced our range the first year. Even the repairman says everyone has had the same issues. For what I have paid in repairs I could have bought a new range.

When I completely remodeled my kitchen 6 years ago, I actually went AGAINST the advice of my appliance dealer and kitchen designer and insisted on buying the Dacor 30 double convection wall oven. Id been longing for Dacor ovens for years and though they gently tried to steer me towards Miele or Electrolux, I dug in my heels. Ive regretted ever since. Since first use, my electronic display has not been without an error message. Every time I go to turn on the oven, theres a message telling me to clean the convection fan filter. I called Dacor and they told me to ignore it! It was a mistaken message. Still, I cleaned them repeatedly to no avail. The main electronic circuit board on the oven has gone out three times. They paid for it the first time because it was under warranty. The second time they sold me the part at a discount but I had to pay for the service call. Total cost to me: $480. The third time, I had to pay for everything myself. Total cost to me: $870. They told me its because I broiled with the door open. I have NEVER broiled with the door open! The inside lights go on and off randomly. The temperature probe has NEVER worked properly. Last week, I was preheating the oven to bake some cookies and an alarm went off giving me a cooling fan error message. The oven turned off and I cant get it to turn back on. I called Dacor customer service twice so far and the first time they told me they would research the issue and call me back. They NEVER CALLED. I called again and they told me they could ship me the part and I could pay for the service call. The lower oven is currently working so I havent done anything yet, but the oven originally cost me well over $5,000. I have put another $1,300 into it. Im not about to spend another $500-$600 on this complete waste of money. Bottom Line: Dacor sells junk for exorbitant prices and refuses to stand behind their products. I was an idiot to fall for the Only True Convection Oven in the market line. Im buying a Miele or a GE to replace.

This week Dacor installed my 2nd replacement gas range. I remodeled my kitchen 3 years ago and chose Dacor because I had a great experience with their appliances in the past, had their oven and stove in my kitchen for 15+ years and never had a problem. With the first new range, the oven started to automatically shut off due to excess heat escape, so the safety feature would kick in and shut the system down, in addition the knobs would become very hot even when the over was used briefly, 12-15 minutes. I was very impressed and happy with the customer service through Dacor, they immediately gave me a brand new over. Exactly another year, the new oven had the same problem, door begins to not hinge properly and heat begins escape, knobs get dangerously hot.This week Dacor very kindly, replaced my appliance with the new Dacor Renaissance 36. I used the oven for 12 minutes on 400 and the entire exterior is dangerously hot. I do not have any children, however, if I did I would be terrified that they could seriously injure themselves. The exterior of an oven should not become hot like this. Has anyone else had this issue with Dacor? I feel they have been very responsive with regards to customer service however I want an appliance that is safe.

We purchased this high end Dacor range (Dacor Renaissance ER30G) new in 2011 from the Appliance Loft here in Cincinnati. It was dropped off and installed and would not operate right out of the box. A repair was made and everything worked (unless you count the indicator lights on the knobs, they all went out after approx 14 months). This past November the oven went dead. A1 appliance came out: Determined new control board needed, ordered and installed. Thanksgiving Day, oven dead. A1 comes back, reset the High Temp Fuse. Oven dead 4 days later, A1 returns with a new HTF. Dec 22, Oven dead. As soon as The holiday is over we will call another repair shop and start looking at replacing this unreliable piece of eye candy. Open comment to Dacors design engineers, quality control engineers and management. You should be totally ashamed about this product youve designed. You are supposed to represent the best in American design and quality and this falls below that of low end appliances out of China. See you in small claims court.

The glass plate in the bottom of the oven has been a disaster from day one. Anything that drops on it leaves a white mark that is impossible to remove. It finally became so discolored that I had to have it replaced; over$100 for glass and factory-trained repairman charged $285 to install, a ten-minute job. I wish someone had told me of the problems before I spent over $5,000 on a range which should be useable, not just pretty to look at which also doesnt happen when the oven is all stained. Burners are tinny and dont begin to compare with the Thermador I have in my other home. I will never purchase another Dacor product.

In September 2009 we did a complete remodel of our kitchen. Replaced everything but the refrigerator, with DACOR appliances. Within a few months we had problems with the dishwasher and finally replaced it with a GE in 2012. About that same time we had problems with the Dacor Epicure 30 Single Oven Model EO130SCH control panel and had to have the repairman out to work on the relay/computer board. At Christmas 2015 I had trouble baking, the temperature wasnt accurate and have had the repairman again. He says that the computer board is fried (his term). Ive tried calling Customer Service with no success. Ive e-mailed them with same results. The appliance repairman has told me that he cant find the part. All the distributors that hes called have been told that the part is on back order. Ive been without an oven for over two months now with no fix in sight. Have been told that IF we find the part it will probably run around $500.00. These are appliances that are only six years old and have had gentle use by senior citizens. Anyone reading this - PLEASE DONT BUY DACOR! Youll be sorry as I am.

Dacor EO227SCH - double wall oven. Installed all Dacor appliances when we did a kitchen renovation in 2008. Stove top, Micro Wave and Warming Drawer each have been excellent. Ovens have been a nightmare. Dacor would not honor warranty 7 days after it expired. Had no less than a dozen service calls in first 3 years. Ovens conveniently have problems around holidays. Example: lower oven quit working two days before this Thanksgiving - last week! Paid a high price to get Dacor and have paid thousands and spent countless hours on service calls since. Am totally dissatisfied with Dacor products and the companys refusal to stand behind its product. I tell everyone who is contemplating Dacor not to. Did it today with a couple who signed a contract for a $1M home in N Atlanta. Builder specified Dacor and I strongly advised against it. Homebuilder is now looking at other options.

The Discovery Model 30 electric wall oven - After 6 years, the oven failed. The fan motor went out and at the same time, we were advised by a very reputable appliance repair recommended by Dacor that we need to also replace the computer or brain. Total cost of repair: $1150 with a warranty of one year.

Purchased a Dacor freezer. Freezer does not come with outer panel. Understandably, because you can choose to put your own custom panel on or order one from Dacor. Found out Dacor was bought by Samsung, a few years ago. So I decided to order a Stainless steel door from Dacor. One of Dacors reps suggested I order from J@J international. I placed order and two days later they called back saying they cannot ship door to me UPS nor FedEx will ship it. They refunded my money, so I reordered from someone else. Got ss panel toe kick and handle. Opened box only to find out no hardware, brackets ss trim for sides screws and so forth. I assumed mounting hardware would be with door. So began the part search for parts. Come to find out Samsung changed Dacors part #s. Vendors who sell the parts could not come up with parts or told me not available. Reliable parts agent told me this. I was told they should have come with freezer. Meanwhile called back Dacor to someone who specializes in dealing with these issues. She took over 45 minutes of my time giving me the impression she was gonna resolve the issue. She finally said we have the parts and inferred that I must have not talked to reliable parts. I assured her I did. She continued to refute what I told her. I have been right at two months trying to get freezer door installed. I called an Appliance dealer in Salisbury Md. to get assistance. He told me when Samsung bought Dacor he dropped line. I now see why. It has been the worst experience I have had with a company that has absolutely done nothing but appear to be concerned and say they are sorry but do nothing. It looks like it will be another 750.00 to get a couple little trims and brackets and a few screws. If I had it to do over I would never have gone down this road. This has been a two month old nightmare that is still going on. Best advice I can give is steer clear of Dacor/Samsung. Was going to buy matching column refrigerator. Not now.

I owned a 36 Dual Fuel Epicure range that required at least an annual repair for the same thing. The control pad (the pad with the buttons that controls the oven and light) would fry. This would cause the oven light to come on and off like a strobe light. Luckily, I purchased an extended warranty from the vendor, as each time this was replaced it was $750+ to repair. When I complained to Dacor on their support line, the representative actually told me that I was running the oven too hot!About 6 months ago, I sold the house and left the very expensive range behind. It was problematic from day one. Other repairs included replacing the ignitors. After a year of use, the insulation on the door came loose and was hanging in plain view through the window on the door. Every repairman that came to service the range said the same thing.... that they repair a lot of Dacors. When it worked, it was a great range. If you do buy a Dacor, do yourself a favor, buy the extended warranty. You will need it and it will pay for itself.

I moved into a house that already had a Dacor unit in place. Within months, I discovered that I owned an oven that could be fixed by throwing the circuit breaker. Then, I learned about invisible hands that turned the 325 degree convection oven to a 500 degree broiler. The final act was having all three glass panes shatter and the control panel cracking as punishment for assuming that the oven cleaner on an expensive gourmet stove would function according to manufacturing standards. The repairman ordered replacement parts. He spoke with someone who was off shore so forget about Dacor being all American made. The wrong parts were sent. He has reordered. Meanwhile, I have been without an oven for two months. If this goes on, I am going to Home Depot and buying a Hotpoint or GE. It is the same price as replacement glass panels and the control panel.

I have a induction Dacor stovetop. Its stopped working and blinks an error code. Called customer service who didnt know what the code meant. I was told my model was 2015 which the rep said was old. It was installed in 2017. All they would offer was cheaper replacement parts if I paid for someone to come and figure out what the problem was and install the parts. I was told the replacement parts were not cheap though. I was told that because were the second owner of the house they couldnt fix it under warranty (even though it should be covered under warranty) because they couldnt say how it was used before (commercially or residentially). Give me a break!It gives me almost no confidence in getting this thing fixed. Warranty is a joke and customer service is terrible. So far I had to leave a voicemail for the reps next level who will call me back after the weekend. Im waiting to see what (if anything) they will do but from the first rep. I dont have a lot of confidence in their products.

Purchased Dacor Wall Oven EO130SCH in 2011. Rarely used, so never used the self cleaning function. Occasionally wipe with microfiber cloth, eco-friendly cleaners like vinegar and Bon Ami and elbow grease. First problem in 2017 when the oven would not heat up, just before I had guests coming to stay with us. Dacor repair personnel could not make it out for a few weeks, so repaired the issue myself by resetting the thermostat with some creativity and effort. Next problem in 2018 with a U43 relay board error. Can use it for a while if turn off the power to the fuse box for a while, but in 2019 it also started making a clicking noise, and basically not functioning right before I needed it for a party. Cant replace the relay board (which costs more than $300 for the part itself) without pulling out the oven. But why is the relay board failing so quickly? Is there a fan cooling issue? Have talked to Dacor. Poorly designed, poor quality. I would never recommend Dacor.

We moved into our newly built home in April 2012. I purchased the Dacor 30" microwave drawer to complement a 30" electric oven that is installed just above the microwave. I am very happy with my purchase, it is stylish and works well. The drawer is spacious, I can fit multiple food items in it and they all cook evenly. We use it daily and couldn't be happier with it. If I ever move, I will purchase this microwave drawer again.

About 3 years ago, I spent almost $5,000 on a Dacor double oven. We had it less than 3 months when the motherboard had to be replaced. About 3 months ago, I started to get various error codes and a continuous beeping. An authorized Dacor service repairman has replaced the motherboard three times. He was on the phone each time with Dacor, however we still get the error codes and Dacor has told the service repairman that they are stumped and dont know how to fix it.Here I am, having a beautiful expensive oven to look at but was unable to cook a turkey for my family yesterday! It seems that there is a major error in this oven, and I am stuck with a huge repair bill and an oven that does not work. I can only hope that Dacor will step up to the plate and come up with a solution or replace the oven which obviously is a lemon.

We purchased a home with brand new Dacor appliances. Within 1 year, the relay board had to be replaced. One year later, the relay board has to be replaced again. Its $600 each time for parts and labor... The part alone costs $500. The company does not warranty the relay board. At this point, we should have purchased a new wall oven. They claim these are superior appliances. Our gas stove top works well, but the wall oven and refrigerator have been nothing but problematic. We will never purchase this brand again.

We remodeled our kitchen in 2002 and chose the Dacor 36 dual-fuel range. I was preparing a pork roast for a dinner party with the oven on Bake. The roast was just not coming up to temperature, though the display indicated that the oven was at the temperature I set. I wound up slicing the roast and cooking it on the griddle; my hungry guests were getting restless. Then I tracked the oven heat for an entire day with an oven thermometer. The oven would come up to temperature and then cool off. I sent these numbers to Dacor and asked customer service for an explanation. Believe it or not, the conversation was--Dacor: The temperature is going down because the fan is coming on. Youre not supposed to use the Bake setting, but only the Convection Bake or Pure Convection. Me: Why is the Bake button there, then? Dacor: Were taking it out in the next production run. (This hasnt happened. My sister-in-law bought a Dacor last year before I could warn her and the button is still there.) Also, after using the self-clean one time, I noticed a crack on the inside of the oven door, starting in the corner of the window. The inside of the window is now permanently spotted with baked-on grease. Now my oven does not work at all. The repairman says that the circuit board needs to be replaced, and if Im lucky, it will work for a couple of years. The repair will cost around $700 including labor. The repairman told me that some repairmen in our area will not even work on Dacors because there are so many problems. Im considering replacing the stove... a very expensive mistake. Beware of Dacor products.

Arrived in good condition and so far works perfectly. Delivery was delayed by one day because of the incompetence of my local mail service. I bought this microwave, as others have described, to replace a 13 year old Dacor that had not really died but had lost the electronic screen. We put magic marker numbers on the display screen where the numbers had been 5 years ago and kept using all the functions. I decided to replace as, without the display screen, I could not do anything semi sophisticated with this microwave but its motor and microwave capacity was still going strong. This model fits perfectly into the previous 24/27 trim kit. Unfortunately our other trim kit is white to match our old microwave. Decor only has stainless steel now. And the new trim kit for this microwave is flat without the vent slats (plus costs over $300!). From the placement in our cabinet, I think the vented slats are really important to dissipate heat and am puzzled by the change in design by Dacor. The slats are a little tedious to clean but as a TV is above the microwave and an oven below I want the heat to have a better place to go. Ebay has the old trim kit in stainless steel but so far the expense seems excessive for just the outside piece. The internal support bracket for the new microwave is exactly the same as for the previous model so the only part of the trim kit needed for my microwave is the outside frame. This newer model works very similarly to the older version. I am delighted Dacor still makes this microwave to fit my space 13 to 15 years later.

The oven I purchased is the Dacor double oven, model number - ECD230SCH, I purchased extended warranty on the ovens. This was purchased when I bought the ovens. I have renewed this and still have a warranty for 2 more years. I cannot get anyone to do the repair on this oven. My location is at the Sardis Lake. I cannot get anyone out to service. I do not know if you have any thing to do with this. I have had an oven out since June 2013. Please help, Dacor should have service reps in this area. I am in Sardis Ms.

My oven would not work. Neither the broiler nor oven element would heat. The dealer from whom we purchased the range had gone out of business. So, I wrote to customer service on the Dacor site. Dacor customer service was back to me within 24 hours with a suggestion on what might be wrong. My husband followed the easy directions and my oven is now working! I am very happy with the prompt reply from Dacor customer service. They even provided a dedicated phone number if we had problems.

Im planning a kitchen remodel and stumbled on this site. I have a Dacor dual fuel range (stove wont light, oven wont hold temp), hood (light wont stay on consistently), microwave (replace once, okay now), wall oven (panel out) and warming drawer. Only the warming drawer is working correctly. I live in rural Kansas and I cant get anyone to do repairs. I really like the design but... its time to move on to a new brand!

Dacor appliances were installed in a new home I purchased. The refrigerator has been out of service every single year since purchasing the home. So far, two thermistors, one power supply board, one drip pan heater and one ice maker. Every time the unit fails, I have to wait several days for the authorized service provider to come to the house. That will then result in the need to secure a part that will require anywhere from three days to three weeks before the unit can be placed back into service. As you might guess, perishables dont last that long, so every event results in the loss of hundreds of dollars of food. After yet another extended outage experience, I called Dacor to find out what they might propose to make sure my refrigerator actually performs in a reliable manner (apparently I didnt get the fridge with that feature). The short version of the story is that they not only failed to ever apologize for the fact that their product doesnt work, they insisted I produce detailed documentation covering the last four years of service before they would consider taking any action. Shame on me for not keeping all the invoices from the two service companies. After numerous exchanges, an offer to pay for the part associated with the last repair, not the labor, was the best they could do. Apparently, $250 is too much for Dacor to invest in a customer who has paid several thousand dollars in repair bills and lost hundreds of dollars of food for a unit that is four years old. This is a company who obviously cannot design a product that works consistently and cant provide after sales support in an effective manner.

We did a complete kitchen remodel in 2007. I wanted top of the line appliances, and I liked the look of Dacor. I spent over $10,000 on a refrigerator, oversize dishwasher, microwave oven and a warming oven... (I know). Within 16 months, everything started to fall apart. Of course it was over the one year’s mark so there was no replacing of the units on the manufacturers part. I have since replaced the motherboard on the dishwasher twice... total of 3K in repairs! I cant replace the dishwasher because it was oversized and we built our cabinets around it and no other company sell an oversized dishwasher. I have replaced the microwave oven with another one that looks just like it because for some reason it fried. The refrigerator constantly rattles and my husband and I are at our wits end because of it. The only thing that hasnt fell apart yet is the warming oven. Probably because we dont use it. I wouldnt recommend it to anyone. Its a total waste of money. Next time Im buying Kenmore. My old Kenmore is sitting out in the garage being a good and faithful second fridge.

I bought DCM24S DACOR 1.5 CU CONVECTION MICROWAVE-SS and after few months of using this product its banded on the back wall of the microwave that supposedly resulted from improper turntable placement which caused the turntable tray to make contact with the back of the oven. The quality of the product is very poorly, dont buy Dacor product!

We bought a 36 inch Dacor range with oven last year, around September, when we moved in to our new house. We tried to turn the oven on Thanksgiving day for 10 people, but it would not work. We called for service, and they replaced the circuit board. The repairman turned the oven on, and it worked fine. We never used the oven, just the burners on top, because we have a second smaller oven, we like to use for every day cooking. Then came Christmas day, and we were having 30 people over, so we went to turn on the Dacor oven, but to our horror, it did not work again. We have owned this oven for a little over a year, and have tried to use it only twice. In that time, both on holidays, with a lot of people to feed. This time, when I called for service, they told me I will be charged $198, because when they tried to get Dacor to drop that charge, they said no. We are very disappointed in Dacor for not caring more about the customer.

We bought a whole new kitchen's worth of Dacor appliances - the Modernist line. It's too soon to review their performance, but so far they work well and look fabulous. Most importantly, I had an issue registering my appliances for warranty. I sent an email and not only did they resolve all my issues, registered everything for me, they also notified me I was eligible for an extended free warranty program, and they set it all up for me without any effort on my part. I wouldn't have even known if they hadn't done it for me. So far, I'd say that they have stellar customer service. When researching online before making the choice to go with Dacor, I had trouble finding information and reviews. I wanted to make sure and share my good experience since all too often people only share when they have had a negative one. I hope this is helpful to someone looking to buy!

This is our second Dacor wall oven. It is approximately 6 yrs old. December 22/14, I was cooking a Christmas turkey as per usual, and I noticed an odd smell about 40 mins. into cooking. Checking the turkey, the temp. was at 500 degrees and on broil. I burned holes in my oven mitts on the roaster taking it out. Even though I set the temp. at 325 convection roast, it reset itself to 500 broil. Nothing works except the clock. Called repair guy after the holidays. Said it is a control panel behind the keypad area. Ordered the part. Been waiting 4 months now for this part. Now, no Easter dinner either. After reading these complaints, I am worried that this part replacement may not be the end of it.

As a contractor, we were fortunate enough to build our dream home which was completed in 2005. After much research and many show room visits, we purchased Dacor appliances for our kitchen. As the saying goes, if I knew then what I know now. Our biggest (note I said biggest, not only) issue is with our ESC130 oven. If you own this oven, do not, repeat, do not, use the self-cleaning mechanism. I have had this repaired once and then replaced once (along with a relay board). I seldom use this because I know when I do the lock mechanism will continue to cycle until it is replaced. This means, while I can still use my oven, I have to time when I open the door based on when the lock is cycling in the unlock position. I must also turn the oven off at the circuit breaker or listen to the continuous warning beep that the lock is cycling (as if I didnt know).After repairing this feature once, I next choose to have the mechanism replaced and Dacor offered me a discount on the parts (the oven was and still is out of warranty) at a cost of more than $500.00. This is on top of what I had already paid to have it repaired just 18 months earlier. I feared using this feature again as I didnt want a repeat performance. After cooking macaroni and cheese yesterday, I felt I really needed to clean the oven and made the mistake of using the self-cleaning feature of the oven. I dont know why I was surprised when the locking mechanism refused to stop cycling.I contacted Dacor today only to speak with the rudest customer service representative I have ever encountered, Steven. No last name. He is the only Steven who works there. He refused to listen to me, spoke over me when I did try to talk, and did not allow me to speak with anyone else. There are no supervisors available on Fridays and he could not transfer me anywhere. I left a message for someone else to call me (they did not). I called back later that afternoon and was given the name of a supervisor, Nhi. She was not available and I spoke with another customer service representative. I learned that Dacor is aware they have a problem with this locking mechanism and are trying to correct it. This got my hopes up, thinking that the company would now do the right thing and replace this mechanism at not cost to me, or at least at no cost for the parts. Not so. Even though Dacor knows there is an issue with this mechanism and they are supposedly trying to correct it, all they can offer me is a discount on parts. Really? Wow! A discount for a part that you know doesnt work properly and probably wont work properly because they are still working on the problem? I just really dont know what to say. Is this supposed to make me happy as a customer? Would prospective customers want to buy a Dacor product knowing that Dacor is more than happy to sell me a known defective product at a discounted price and they should expect the same? It is probably needless to say that I would urge all prospective Dacor owners to not waste their money on any Dacor product as they do not care about their customers. I will certainly be doing my part to warn others and hope this serves to warn others as well. Dacor has a lot to learn in terms of building even what could be called a good product and standing behind what they sell as well as becoming a customer service oriented company.

I wish I had read all these reviews of Dacor products before being duped into paying for a high end wall oven. As many others have mentioned, the electronic panel design is faulty. I paid $1000 to have it replaced once. Now it is broken again and the alarm beeps constantly. The reply from their service rep was that they havent had any recalls of this product (in other words, no ones house has burned down yet). He also admits that he wouldnt buy a Dacor oven unless he had money to burn. Well, my money has already burned and so have I.

We bought this oven and had it installed a month ago. Id love to love it, but unfortunately I dont even like it. Immediately after installation I noticed the touchpad for the bottom oven didnt work. I called Dacor and spent quite a bit of time while someone did the standard is the power on run through. I was told someone would have to call me back in the morning, at 9 am. The next day at 10 am having not heard a word, I called back. I was given the option to be called back (you wont lose your place, and our first rep...) Great! Nope. Four hours later still nothing. I called back again. Someone answered quickly and after a short call arranged for a service person to come out in a few days.Fast forward a few days and the serviceman arrives. Hes clearly never seen this kind of oven. He calls Dacor and talks to their troubleshooting department. They decide the motherboard is bad and reorder. Well, its been 10 days. *crickets*. There is no sense of urgency... In fact nobody even seems to care that my $7500.00 oven doesnt work and the microwave literally cant even pop popcorn. I would expect the company to rush delivery of the part. If need be replace the whole oven and figure out what is wrong with the motherboard on your own time. What I didnt expect is for literally everyone involved in the process of choosing and buying the appliance to not be able to find a solution. I give my new oven 1 star out of 10, because it looks nice. Id rather have an oven that doesnt have a smart feature and actually works. FAIL Dacor.

Dacor came through! They sent me, at no charge,a replacement part. This new part is supposed to fix the issue of ice cycles in the freezer. Its a new drainage system that actually heats the water in the pan so it does not freeze up causing the water to back up. I am hopeful that this will permanently fix the issue! But props to Dacor for stepping up to the plate to fix this! Thanks, guys!

I purchased entire kitchen of Dacor appliances - $30,000. The 48 refrigerator required 9 service calls to stop freeze up. Wall oven – the digital panel went bad. Stove top exhaust – the circuit is melting. The dishwasher had 17 service calls over 2 years - mid way they replaced the unit because they could not stop it from leaking and damaging our wood floors. The most recent service call was yesterday, 12/20/2011. After waiting since November, it is again not working. Does anyone else understand that spending $1700 on a dishwasher should allow you to use the dishwasher? I called the customer service and was told We are discussing the situation and will get back to you. Are you going to come wash dishes with me over Christmas when we have 25 guests? Were you there on Thanksgiving? If I hadnt been stupid enough to buy all Dacor appliances, I would throw it in the dumpster and buy a GE from Home Depot.

Unfortunately, the screw broke in two that held our Dacor refrigerator door on and much to our dismay, the door fell off. Dacor was prompt and courteous in sending a replacement lower refrigerator door hinge to the service company and covered the full cost of labor even though they initially said the refrigerator was out of warranty (two years old). Our experience was positive with James who gave timely and a customer-focused response. He also called to follow-up after the repair to make sure we were happy which I appreciated. I hated that the door broke but was very pleased with the repair and the fact that I did not have to pay.

I could have written every one of these negative reviews. Ive had all the same issues with my Dacor Epicure oven. Faulty computer panel, failed motor in the downdraft fan, oven not maintaining temperature (meaning NOTHING cooks correctly in this oven), burned out lower element and discolored interior. And let me add that the interior oven fan stays on for about half an hour after you turn off the oven. What purpose could that possibly serve???? Suffice it to say that this is a poorly made product by a company that has no desire for repeat customers. I am currently working with customer service to try to get my oven working for Thanksgiving, but I just dont have much hope after reading all of these similar issues. Clearly, they manufacture a sub-standard product and sell it at premium prices. Nice business model, for a while.

I purchased a Dacor Refrigerator about 4 years ago and have had nothing but constant problems with it over the years. Finally they agreed to send me a new refrigerator, and now after five months I am having a major problem with it, and have been trying for 3 hours to get a warranty authorization from them so I can have a repair man come out and stop a major leak that is now leaking into the condo below me. I am so disgusted with their products and their service that I really would never advise anyone purchasing a Dacor product. If I could I would buy another brand then be done with it, but this was a $9,000.00 refrigerator - CAN YOU IMAGINE THAT???

Liked the look of Dacor oven and fit in with remodel. Relay board replaced year after warranty - $600. Then after 8 years of light use (have Thermador home pro stove), another circuit board failed, part no longer manufactured. Oven now worthless and headed for landfill. Outrageous! Large national appliance retailer says Dacor not reliable. Daughter had major problems with Dacor fridge. Have purchased Kitchenaid replacement on recommendation of same retailer. Built to not last...shame on you, Dacor.

I have a Dacor 27 inch wall (model EOR) oven which I bought 2 years ago, along with a micro and a warming drawer. Since then, the control panel has been replaced twice. Both times because, after using the timer mode, the beeper would come on at all hours of the day and night. In both instances, I had to cut the power to the oven until the replacement part arrived. I am presently waiting for the third panel to arrive. Today I needed to bake something, so I turned the power to the oven back on. Now it will only function at 350 degrees and only in the bake mode. No other numbers can be put in and nothing happens when I select convection. So far Dacor has absorbed the cost of the parts and repairs, but that does not mitigate the hassle of having to wait upwards of 2 months for a part each time this happens.

Bought expensive refrigerator in Miami. And because I live in Miami 2 months in year use and tern in refrigerator only for 2 months. Every year have problems for thousands dollars. Company keep changing parts. I keep paying. Same problem every year. Big mistake to buy Dacor appliances. Regret very much and angry. People who fixing they know nothing. Only money. Very not happy. Looks like new. Today will throw on the garbage.

We bought our Dacor 30” gas range in September of last year. We were tired of cheap stoves that lasted 5 years before they needed to be relegated to a landfill. We thought it was an investment that would provide us with a reliable appliance and worst case scenario, better warranty repair service than Home Depot or other big box store.After 15 months, the igniter for the oven stopped working. We tried the 800 number on the warranty registration website and no one there could bring up our registration, even though I could see it on the website. They gave me an email address to contact the people who could look it up and I heard nothing for two days. I called the 800 number again and they transferred me to another number and they finally found our warranty registration and issued a ticket for the repair.The company they use for warranty work in Toronto, is Home Appliance Repair GTA and they are absolutely horrible. They said they ordered the part on November 27, but they did not actually order it until December 6th. Dacor then sent the wrong part! I demanded that they send the proper part overnight and on December 13th they called and left a voicemail saying that the part would be here by today at the latest.It did not arrive and this evening I emailed them again and their response was that the part would be here on December 19th. How does it take a week in this day and age to deliver anything? I don’t believe that I will even have a functional oven for Christmas this year. I have already given up on any baking getting done. I will never buy a Dacor product again. I actually really love my stove, but I am beyond disappointed with their warranty service and customer care.

Purchased Dacor Induction Range w Convection Oven RR30NIS-C in October 2013 and LOVE this range. Accidentally broke the glass on the induction cooktop with falling object mid-March 2020. Only the glass is broken, and all other electronics, induction burners, oven, etc are functioning fine. Called Dacor support to acquire part number for a glass top for repair - obtained part number #701751 superseded by #702285, BUT was informed that the part had been discontinued and is no longer being manufactured or kept in stock. No other advice was given other than to discard the entire $6000 range. Multiple phone calls with service.I asked for a listing of third party part distributors and was referred to four distributors on the Dacor public website and given no other info. I called all web-based third-party distributors I could find in USA and Canada to see if anyone had the part in stock, with no luck. I contacted two technicians to see if they would be able to obtain the part through their channels, with no luck. I am an engineer, so I spent some time pouring over technical manuals trying to find a solution to replace the entire induction range cooktop assembly (top part of the range) with a later model, and although its possible, Dacor would not provide the ability to purchase an RNR30NI range cooktop assembly that could be fit into the existing housing on top of the range. The convection oven is completely fine, and I cannot believe that Dacor has given me no other option but to pitch a six-year-old $6000 range because they stopped manufacturing one fragile part made of glass. I would imagine that many consumers may be in the same position as I, as these cooktops are breakable, and accidents happen. I have reached out to Dacor support desk numerous times without resolution, and I am at my wits end with a $6000 boat anchor in my kitchen. What a waste of money! Poorly done Dacor!I would like Dacor to provide me with some sort of solution whether it be the part required to fix my induction cooktop, or a replacement Induction Range with convection oven, or reimbursement of the purchase price so I can obtain a replacement on my own. If I am not able to find a solution to repair my range, I will never buy from Dacor again! Dacor will discontinue easily broken parts without warning! You may spend thousands of dollars and not be able to repair your appliance after warranty expires!

Epicure Range, wall oven, microwave and fridge - When remodeling our kitchen in 2010, an appliance salesperson gave us a good deal on the entire set. We spent $20k on the Dacor appliances. BIG MISTAKE! Do not ever buy anything Dacor. We have issues with every single one. Where do I start? The ovens have gone out three times now and I have had to replace the main panel, now it will not heat at all. The refrigerator 42 built-in is a big piece of crap! We have had it serviced 4-times for everything. The entire fridge freezes over due to a design flaw. The fan in the freezer completely ices over. The ice door broke. The crushed ice broke. The plastic door for the butter broke. The shelves broke.The microwave has had issues and has had to be fixed. The oven temps were wrong. Fixed those myself thanks to YouTube. When talking to the service guy he said that these are cheap appliances with the Dacor badge, so you have to spend big bucks to buy them and big bucks to repair! Do yourself a favor and if you are thinking of Dacor run! I contacted Dacor and they are even worse to deal with. They did not care that their appliances are very unreliable. Never received a return call, email, or even a letter.

We chose DACOR (8-burner double oven top of the line ERD60S06CH/LP) in 2006, new construction because we disliked the signature blue interior of another luxury brand. Last October I detected a gas leak from one of the burners. The authorized repair company was contacted, and the entire unit - all 8 burners and both ovens were out of commission while we waited for the replacement part. Six weeks later the repair guy returned with the wrong part. We had to wait an additional month for the repair guy to return. Apparently, not important that people might want to cook and bake before the Holidays! After the new valve was replaced the oven light began to turn on when any of the gas valves on the defective side was turned on. I write this review 8 months into the problem. I can fix for $700 by ordering a new control panel. I wish I had read these reviews earlier. I overheard the tech say that there was electrical interference and that the wires need to be insulated to stop the oven light from turning on and off. I am so FED up with both the Dacor California head office not caring and the horrible authorized service company. I will take this unit apart myself and fix it. DACOR IS GARBAGE. Go with Sub-Zero, Miele and forget this Brand. DACOR: Dont Accept Crap Or Rubbish! Made in America? Shame on you. No problems with 4 Sub-Zero fridges, or 4 Miele dishwasher the same age.

My Decor Epicurian oven and range has been a nightmare from day one. I have had the oven for about 8 years and had it repaired so many times I have lost count and had spent at least $2000 on repairs. We have experienced motherboard burn out, membrane failure, temperature control malfunctions, error messages that cause incessant beeping. Nearly all of the problems that have been described in this list of complaints, I have had the problems themselves multiple times! Now, I am panicking a bit because I decided to use the self clean function on my oven this morning and now, I have read some sad malfunction stories following the use of this feature. I am so torn about whether I should just cancel the cleaning process. I do not want to risk having the oven malfunction again, but the thing really needs to be cleaned.

ZERO STARS if I could but DISAPPOINTED - if I had to use one word to describe our experience with Dacor with not only our $8K+ 42 Built In Refrigerator that is sitting at 70+ degrees in the freezer and fridge sections but SO DISAPPOINTED with their poor customer service and lack of concern resolution tools for their team to even try to help.They are supposed to have high end luxury products. With that, anyone would expect to have a luxury customer experience. However, our family has been WITHOUT a working unit since January 6th. That is less than a month from when we had it installed but almost a month from today. We followed the proper protocols to get it repaired. Took almost two weeks to even get a technician. Once we did, he confirmed it needed to be replaced. We got approval and now learned we have wait another 2-3 weeks to get a separate decision to be made.Requested if there is any way to escalate our concerns but cant even talk to a supervisor for another 24-48 hours... Apparently they will call when it is convenient to them. Dacor - have some empathy for your customers! Imagine paying for a high end product to have no working fridge or freezer for a family of 6. Not sure how this is an acceptable practice. POOR QUALITY, UNTRUSTWORTHY, DOES NOT CARE ABOUT THEIR CUSTOMERS.

Ive had the 27 inch double wall oven for 10 yrs. When I purchased them they were 6000 dollars. With 3 years I started having a problem with the motherboard. It has been replaced 3 or 4 times. Ive lost count. The last time they said it was fixed for sure. Well today the same issue is occurring. Im done! Never buying another Dacor product again.

I purchased my Dacor Distinctive #DT0127 wall oven in 2015 and have been very pleased with the product to date. However after running a self-clean cycle the oven does not work which was a surprise given the fact that I had previously done self-cleans before without any problems. I immediately contacted Dacor customer service who were amazing! The CSR that I spoke with kindly extended my warranty until 2018 even though I had not registered my oven with them upon purchasing it. He also arranged a service call for me that would be covered under the extended warranty. I am very impressed with the companys attention to service as I really love my oven. Even though I experienced this issue I would still recommend this product.

My wife and spend $12k on a new Dacor range/oven 15 years ago. The range works well, the LED lights on the gas knobs needed changed once in a while, the oven door wouldn’t close properly and the heat in the oven wasn’t distributed evenly. All that we could live with. Then the oven died. The repair technician ordered the part. Samsung don’t make it anymore. We are now left with no oven. So we have spent $800 a year on a Dacor range that now doesn’t work. Thanks Dacor… or Samsung?

In 2010 we purchased a new Dacor Epicure Stainless Steel 42 refrigerator/freezer. Weve had to replace the freezer heating element (twice) because it fails and then the freezer ices up causing the system to stop cooling. This past week the fan began making a noise and so we had repairmen come out (yet again). Technician confirmed that the pan motor (fan in freezer) has failed. NO PART is available... I couldnt believe that parts wouldnt be available for a $10,000 high-end refrigerator that was purchased new only ten years old. I called Dacor directly and asked them how long they make parts available after they retire a model.The Dacor representative told me that they make parts available for 7 years. 7 YEAR PART AVAILABILITY ON AN APPLIANCE THAT SHOULD LAST 15-20 YEARS??? RUN AWAY FROM DACOR. Obviously customer service is low on their priority list. We will be replacing our gorgeous $10,000 ten-year old Dacor refrigerator/freezer (now a boat anchor) with Sub-Zero. Not too much more money than Dacor but they continue to make parts available for twenty years following model retirement. That is the kind of company that I want to do business with.

My wall oven spontaneously heating to 800, will be fixed! Thank you, James of Dacor for contacting me again and for arranging for my wall oven to be repaired at no cost. When our oven is in top working order, we love the convection option and we love the internal temperature probe. The people at Dacor offer the friendliest service I have ever encountered and I thank you so much for that.

We remodeled our kitchen 2 years ago but didnt upgrade our refrigerator because our old one was still working. My wife and I always wanted a Dacor refrigerator. We like their design. Our old refrigerator finally died after a little a year after our reno. We were sad but happy at the same time because we can finally go buy a Dacor fridge weve always wanted. We shopped around and compared Dacor, Sub-Zero, and Thermador just to make sure Dacor is for sure what we wanted. We chose Dacor and we couldnt be happier. Its been almost a year and we still love our Dacor fridge. Now we will just have to wait until our oven dies to get a matching Dacor one.

Thank you for your attention. Since my post, a resolution has been reached and Dacor will be replacing my range with a new one. That is much more representative of the pride and reputation of Dacor. The executives were very responsive. Perhaps front line agents are not empowered to make these decisions, however, in my case, the escalation brought the matter into the right hands. Happy with the direction towards the final outcome, not the 4-month process that discounted the reputation and my perception.

We purchased the Model MOH130S in 2006 from a very reputable distributor of high-end appliances. In 2009 we required a service call to deal with temperature control. The oven was out by more than 40 degrees Fahrenheit. This resulted in a relay board, item 101559, to be replaced. Dacor was nice enough to cover the cost of the board, but not the cost of the $152.00 service call. In 2013, guess what? Relay board, this time out by more than 50 degrees, item # 101559 required replacement again only this time it was not covered and cost of $628.00. Here we are, 2016 waiting for the service provider again as temperature is out by over 60 degrees. Roasts, Turkeys, Chickens and everything else have been dying slow deaths in this unit and are awaiting yet another bill to deal with temperature control. Dacor will do nothing until another $150 service call confirms the problem. Hmmm! What to do?

This is the second time I have purchased these appliances and unfortunately each one has been a great disappointment. I have spent enough in repair bills to almost purchase a warming drawer. Each one shuts down when the self clean button is turned on, and then I have to call a repairman out to recalibrate the oven to work each time I try to use the self clean. I was told by the last repairman that the life of the oven is greatly shortened if you the self clean mode. If this is the case, either fix it or take out this mode. After I had the oven about a year the oven door glass blew out, and this had to be replaced. The temperature in the oven is very unreliable in different areas of the oven and browns more on one side than the other... For the high end cost of these ovens, I would just as soon have a basic oven that works and does not go out every few months. What a waste of money I consider Dacor to be, and will never recommend it to anyone I know. I am in the personal shopping business and have my own company, but will tell my clients to be very aware of the high cost/low performance of Dacor products... On a scale of 1 to 10, Dacor gets a 1.

This is a follow-up to my prior comments on the 30 Dacor wall oven. After posting the prior complaint, a Dacor customer service representative emailed me immediately the following day asking for details on the problem. The Dacor rep immediately called my repairman, notified me that they were working on a solution, and then followed up with a solution that exceeded my expectations. We are very satisfied with the outcome and should have called Dacor directly at the onset. Thank you Dacor!

Regarding my previous complaint on 3/21/12, I had a Dacor fridge, model #EF42BDCBSS, installed in my brand new kitchen in March 2008 (Ive a kitchen full of Dacor). It subsequently had a problem with the drip pan in March 2009 and was fixed on warranty. Come March 2012, the fridge was again diagnosed with the same problem. The technician told me there had been a design problem, but after three re-designs, it was remedied and should have no further problems once the new part was installed. The bill, $658 and more than half, was for the part! Of course, I was livid because the fridge had been fixed in 2009 and was now off warranty.When I expressed myself originally, I was simply venting about the price of the repair without hope of a remedy. James at Dacor customer service called me promptly that next morning and left a message! We subsequently talked and he immediately got in touch with my local appliance service center. He not only worked out with them refunding my deposit for the part but also ordered two other parts that were necessary in order to fix the problem. The outcome? They fixed my fridge at no charge to me for parts or labor, and all I had to pay was the original trip and diagnosis charge. I cant begin to tell you how extremely happy and grateful I am about this. Thank you, James, for such terrific follow-through and thank you Dacor for being a top-notch business who stands behind your products!

Dacor range - After I posted my comments on August 8th, I was contacted by Dacor customer service immediately and the new part was sent to me free of charge. I do have to pay the labor, but the part was what was expensive before. They did give me an explanation as to why this was happening - the hinges on the door wear out and the door doesnt shut properly so that heat escapes. Should this be happening with a stove that was this expensive? I dont think so, but I am happy with the customer service I received from Dacor this time.

I purchased the Dacor panel ready refrigerator and freezer column 15 months ago. The refrigerator stopped cooling -- in 15 months! These were 8k each!!! It had now been over 2 months without a working refrigerator and no end in sight. I will never ever purchase one of their products again! They replaced the compressor and 3 days later it stopped cooling again. What a joke! DO NOT BUY DACOR!

I recently upgraded my kitchen and had always heard that Dacor has been a reliable high end brand for kitchen appliances. Their refrigerators have a lot of space, and everything can be easily organized. All the appliances work as intended, and they also all look great. The stainless steel Dacor uses to make these appliances look smooth and clean, making it one of the most beautiful kitchen appliances I have ever owned. If you want a functioning kitchen with appliances that always look nice and shiny, then I would highly recommend Dacor.

We remodeled our kitchen in 2006. I spent a fortune on a Dacor dual fuel gas cooktop with electric oven/convection oven. My Dacor problems seem so normal I mostly deal with it. My 2 biggest complaints are the glass oven door is not airtight, it is darkened between glass, very hard to monitor my baking. And the temp gauge has always been off by 15-25 degrees. I use an in oven temp gauge, which has been calibrated so I know it works. If anyone is planning on a Dacor, you will get the best looking range. It just wont work.

This is an update on my posting regarding our ER36DSCH/NG posted Dec 30, 2013. A Dacor representative has been in contact with us and has offered to install a new oven control which they think will resolve our problem. We are absolutely thrilled and quite surprised that they are footing the entire expense. Now this is what I call good customer service! Thank you Dacor.

I purchased my first Dacor appliances in 1991, built a second house in 2005 and again purchased Dacor double ovens and a cooktop. Loved them! Remodeled my current home and again purchased the double ovens and a cooktop. The double oven, DTO230FS, which was installed in November 2015, 4 years ago, stopped working. I was roasting asparagus and we smelled what seemed to be burning plastic. The oven is used about 4 times a month, I have never used the self cleaning feature therefore it is surprising that it broke. The repairman said that the relay board was bad and will need to order the part. He estimates that it will be $600 to fix it. Sad that I need to incur the repair cost of an oven that is only 4 years old.

Dacors wall oven wont heat up after I used Self Clean feature. Dacor said there is a reset button behind exhaust frame on oven (close to door latch). I called when I could not find red button and was told it was hard to find and they did not know exactly where it was located. Maybe I should call repairman. Any suggestions? Has anyone else had problems after cleaning oven? PS: My 5 year extended insurance expired Nov 11.

In 2008, I purchased my dream home and had the opportunity to build my kitchen from scratch. At the time, I shopped Viking, Sub-Zero, Wolf, and Dacor. I made an appointment to tour the Dacor showroom and was blown away by the aesthetics and advertised performance of their line. I made the decision to fill my kitchen with Dacor products: dishwasher (ED24SCH), dual range (ER48DSCH), range hood (EH4818SCH), fridge, and microwave (DMT2420). To date, the fridge is the only appliance that has not malfunctioned. Within the first month, the microwave blew a fuse (covered by warranty). Within the first 6 months, the dishwashers motherboard blew (also covered by warranty).Since the 1-year warranties have expired, the range hoods electrical unit malfunctioned and ceased working properly ($400-plus in repair). The motherboard on the dishwasher has gone out twice ($1200-plus). The dishwasher rack has completely rusted and the wheels have fallen off ($800 to replace). The lights on my oven dial is out and the glass bottom inside the oven that covers the heating element has cracked (nothing has been spilled or dropped). In fact, I only use that side for Thanksgiving. I am extremely bummed (to say the least) and I feel that the products that I was sold do not live up to the quality level that they advertise. Additionally, the replacement parts are obscenely expensive, and at this time it makes more sense to replace the units rather than dump more money into a pit.

I have own my range for about 2 years and for the most part it is used every day. I love the simmer burner and how strong the rest of the burners are. My food always cooks well both on the stove top and in the oven... I love this range.

Updated on 05/12/2020: I wrote a review of our Dacor kitchen and gave the company a review of 2 stars because the cooktop, ovens, and hood blower all have failed at some point. The real issue is that the company doesnt support products after sale to quote them they do their best... The other problem is this site, it allows companies to claim they are or have resolved issues, without a response or comment from the customer about what the Companies Resolution entailed. Sending me an e-mail that says sorry the thousands of dollars you invested in our products only bought you up to 7 years of replacement parts, isnt what most people would call a Resolution. After months of working with the retailer and Dacor the e-mail below is what they consider a Resolution:Subject: Dacor customer service **Hello Mr. **, We would first like to thank you for staying a Dacor customer for as long as you have and would like to apologized for the inconvenience. As a manufacture we are constantly innovating products and at some point parts and units do become obsolete. Dacor does provide parts for as long as we possibly can. Once the appliance becomes obsolete we are only required to hold parts for up to 7 years. We again thank you for being a Dacor customer. Be safe during this pandemic. Have a great day. DENISE ** | Customer Service RepresentativeO: (833) 353-5483 x** F: (626) 403-3130Original Review: We built a new home in 2003 and purchased Dacor Preference appliances. Including a 6 burner cooktop, double 30 inch wall ovens, warming drawer, a microwave, and large hood with a remote blower. All the appliances are stainless. We enjoy home cooked meals and prepared at least one meal a day. Our kitchen is a work place not a show place. So these are my feelings after 16 years of use.The Cooktop has plastic knobs and a rubber gasket under each burner and piezo electric igniters. All of these items have failed over the years. I replaced the burners some years ago because when the gasket fails the burners sputter and liquid spills leak into the bottom of the cooktop. Replacement burners fixed the problem for a while but the burner design makes this a point of failure. Additionally, the burners were expensive so were back to sputtering burners and disassembly for cleaning. One of the plastic rings under the flame control knobs broke, weve ordered a new ring ($26) a couple of months ago but Dacor cant give us an estimated delivery date. For the past few years the Piezo electric starters only light half the burners, (they spark but the burners dont light) not a big deal but these are high end appliances, using a match to light the burners is definitely 1950s.The 30 inch double ovens are a great size for bakers like us. The Convection feature is great. However, the first time we ran the self cleaning cycle on the upper oven the door handle on the bottom oven bubbled and melted. The real issue with ovens today, is that Dacor has stopped making replacement parts including the electric heating elements. So even though we spent nearly $3,200 for these ovens, Dacor no longer supports them.The Microwave never worked correctly and we replaced it almost immediately. At that time Dacor used relabeled Sharp microwaves. Finally, Im not a fan of cooking smells in the house. So, we purchased 48 inch hood with a 10 inch inline blower. This week it failed. The motor hums but the fan doesnt turn. So replacement parts? Nope. If you decide to purchase Dacor be aware that the company doesnt provide support for their products in the long term.

48 in. Range - Wish I had read reviews first would NEVER have purchased Dacor. Paid almost 11,000.00 for a range so many issues they replaced it. New range came with 7 defects. It has been over a month and nothing has been done about it. Everyone keeps passing the buck and I am sitting with an high end expensive product and no help from Dacor. I am being very patient but also very frustrated at this point.

Eight months ago I renovated my whole kitchen with all Dacor appliances, cooktop double wall oven, refrigerator and dishwasher and I could not be more pleased. I wanted to wait a few months before I wrote this review in order to make my review more accurate. I love the modern design of all the appliances. The refrigerator is nice and roomy and the cooktop has been very reliable. Dacor products cost a bit more but they are well worth the extra money!

We are in the process of remodeling our house including an entire new kitchen that we cant wait to finish to invite people over and show. HOWEVER, the cook top already has a light burned and finally the cover of it ended up falling as I was wiping down the stove (very softly by the way because I like to treat my appliances really nice). We have had this stove for less than a year I havent even made the last payment and it is already with a light burned out. REALLY? My husband spent countless hours researching the best appliances and decided to get this one and to come to find out that it is not good it is a complete disappointment. I am sooo upset. DO NOT BUY THIS BRAND!!! Save yourself the hassle that we are now going to go through trying to get a hold of someone on the phone and see what they will do if anything. I bought it from AJ Madison.

We purchased a Dacor induction range 5 years ago which cost $5000 plus installation parts and service costs totalling $10000. Two days ago, an error code showed up indicating that the generator needs replacement. I contacted Dacor who states that the part is discontinued but that I could contact a refurbishing company (Corecentric) to send my generator to for possible repair. A service technician would have to remove the generator, I would send the part to Corecentric, then IF they can repair it, the tech needs to reinstall it. There are no service providers that Dacor referred me to that will service a refurbished part. Even if I wanted to try, I as an owner, cannot remove it myself because Dacor does not provide the service manual to do so. I spoke to Dacor multiple times about this problem and management stated that since the product is so out of warranty that they cannot offer any other repair option, compensation, or replacement even if the part is deemed unrepairable by Corecentric. When you pay $10000 for a product I expect it to last more than five years and that a reputable company would stand by their product and service. Essentially, Dacor inferred that we are out of $10000 because a part that POSSIBLY can be refurbished for $215 plus service costs, cant get serviced and Dacor takes no further responsibility. I have heard stories from appliance providers and service providers that since Dacor joined Samsung, that their customer service is poor and products have become inferior.

When I bought my house, the previous owners told me that theyd been having problems with the Dacor oven. They had purchased a replacement burner and prepaid the Dacor authorized service technician to install it for us. We have worked for three years now to get Dacors authorized service representative to install the part for which he has already been paid, and have been using a toaster oven to prepare meals for a family of four the entire time. The oven will heat to 135 degrees, then either shut off completely or immediately switch to broiling mode and burn whatever is inside it. When I called Dacor to see if they could help with the service issue since the technician was authorized by them, they told me it was my problem, not theirs. Although if the product they manufactured wasnt faulty in the first place, it wouldnt be anyones problem!

We purchased a Dacor oven stove top. It is about 10 yrs old now. 3 years ago we had a problem with the ignitor and had it repaired and paid over $200.00 for the repair. 3 Years later we are experiencing a similar problem with the ignitors clicking on and not turning off. I have called for repairs on this but expect this will cost me some more money. I have been online and have seen similar complaints leading to believe that this is a common problem and I would avoid purchasing Dacor ignitor products for the stove top, until resolved.

We purchased our second Dacor microwave. When received there was a defect on the stainless front panel which we reported to Dacor (now owned by Samsung). They took claim information and we were referred to their service provider. A Samsung inspector subsequently visited our home and got approval from his superior. We were told the panel had been ordered. Two follow up calls revealed that there was a problem and we were referred back to Dacor only to learn the claim was overruled and denied. A subsequent appeal was made to no avail. Our warning is that Dacor repairs are very expensive and they do not back up their service warranties. Buyer beware.

I had an issue with the wall oven light on my Dacor Preference double oven. To make a long story short, after contacting Dacor directly, they made sure that the unit was fixed by providing the part directly to me and confirming that the local repair company would be willing to install it. The oven is 8 years old and in the end, what I spent seemed reasonable to get a fully functioning oven (membrane switch). They were prompt, personal and courteous in their response to me. I came away feeling that Dacor takes pride in their history and their products! They also cleared up some misconceptions that I had regarding the status of their company. Although it was frustrating to have an appliance not work properly, I feel that the customer service Dacor provides makes their company one worth sticking with. That makes a big difference in todays impersonal world.

Dacor refuses to take responsibility for defects in their products. Our wall oven required two cooling fan motors and two relay boards over a relatively short period of time. In addition, all of the sensors had to be hard wired when the oven stopped working, and our service technician was informed by Dacor that moisture tended to get into the sensors on these ovens. We spent nearly $1500 on these repairs. Reaching a customer care representative at Dacor can take upwards of 20 minutes. Phone calls are not returned. Customers are left to pay the cost of defects in Dacor products.

I was and, I repeat, was a loyal Dacor customer. I gutted and rebuilt a kitchen 9 years ago and purchased a Dacor stovetop, oven and microwave. I remodeled my new house 5 years ago and again purchased Dacor stovetop, oven and microwave. Consumer reports provided favorable reviews of the appliances I purchased below.First red alert: The oven Model MORS130S and Microwave Model DCM 24S LED did not match. The microwave was green; oven was blue. The brochure was in black and white so there was no way of knowing that aesthetically they were a mismatch ... it was very sloppy(!) and very deceptive by Dacor. I mean when I waited weeks for my appliance order and the oven is already installed with a big fat ugly LED screen, what was I supposed to do, yank it out and start all over again? This was disappointing!Next, I was simmering chili on the stovetop (5 burner, gas) and, lo and behold, 18 flames started exiting through the turn knobs resulting in a meltdown. The gas was leaking through the tubes underneath the stovetop. I just happened to check the chili while I was gardening to watch the house almost burn down and btw, it was difficult to put out the flames because the natural gas was leaking under the unit. Seriously! I called customer service and they got hopping right out to fix the issue. This scared the heck out of me. It is negligent to have a product like that on the market.After about 13 months into the life of the Model MORS130S oven, the touch panel failed emitting a CO1 error message. I was told it was $140 to fix it and that the panel was defective, great quality there, Dacor. And the added joy to the CO1 error message is that the unit beeps intermittently all day and all night long unless the power to the oven is killed. Joy... now another issue - Model MORS130S oven LED lights are burning out. Seriously, what else will there be? Now its $175 for LED panel and another $100 to install by an authorized Dacor service man.So I called Dacor back again today because the LED light out was annoying me. They offered nothing. To be fair, my appliances are out of warranty but seriously, Dacor nearly burned my house down. They should be winning me back as a customer if they really cared about their customers and having long term repeat business. Never again, Dacor, never!

We purchased a under counter Dacor oven. The timer started given problems, tried contacting Dacor. The rude customer service advisor first talked to me like a police interrogation, then said sorry cant help. A joke of company with cheaply designed products. Never again.

We own 3 Dacor appliances, gas cooktop, microwave & built in oven. From the day of installation of wall oven there was a problem. Without going into detail suffice to say it was repaired 3 times within several months, under warranty. We were having issues with our microwave not working consistently, after several service visits, not under warranty, we now are told it will cost over $600 for the part. We are now looking for another brand of microwave instead of fixing the Dacor. On a side note the rings for our Dacor gas cooktop never come clean no matter how hard you try. The material used are definitely inferior. We have another property with all KitchenAid and have been happy with the performance. Our fridge & dishwasher are KitchenAid and I regret not getting the same brand for our other appliances. If I could give a minus star for Dacor I most certainly would do so.

Add me to the Dacor hate list. The $4300 oven installed in 2000 is now a whopping $6400. My motherboard #2 is broken and the glass on the door cracked which to me is a safety issue. This is a two adult, no kid household so figure. We use the oven about 7 times a year. My Dacor rangetop and hydraulic exhaust have both required service as well.

We replaced a Dacor with this new upgraded Dacor. I accidentally started a fire in the last one...my fault not the units. Ours fits very snuggly into the wall which was the primary reason we went for the Dacor brand. Other than having to take off the little rubber pads/feet, it slid right in and we were back in business.

Front bevel of my first rsd30 range purchased in California in 1999 cracked within nine months. Dacor said it was a defect in the design and would fix it for free. I sold the house in 2001 but the range was still not fixed. I moved to Nevada and bought a new rsd30 range and same thing happened within six months. It took a year to get it fixed at their expense. This bevel also cracked again for the second time in March 2011. Their response to this was to offer me a new bevel for $180 and I would have to pay for the installation. I declined the offer. The bevel is still cracked at this time. At the same time, I bought a PMOR30 over the range microwave and the front handle broke at least four times. And finally, the whole thing broke down and was not repairable. In Aug. 2008, I contacted Dacor and they agreed to replace it with a new DMT2420 over the counter microwave for half the price ($390). Last week, this one blew up on me. Sparks were coming out through the side and a big hole in the removable shield and burn damage to the wall of the unit. I do not believe this unit is repairable. I contacted Michael at Dacor. He apologized and said that theres nothing they can do about it as it is out of warranty but they will look into it. What I want at this point is my money back that I paid for ($390) and for them to pick up the unit and get it out of my house. I will never buy another Dacor product again.

We had a ongoing problem with a wall oven that was purchased in 2006. The most recent complaint was a oven glide rack that was not working. After complaining about it to one of their staff, they listened to our frustration and are sending us a new rack at no charge. My hats off to the great people at Dacor. Thanks for your understanding. Al

We purchased a home with a 5 year old Dacor Discovery IQ Double Wall Oven. Model Number DYO230S. Great looking and it has a very sophisticated and functionally rich digital control system. Problem is the digital control system does not work. The stove has a mind of its own and will just shut off for 24 to 48 hours and return to function randomly. Shutting the power off and turning it back on has no effect. Dacor (Now Samsung) has been completely un-helpful. Bottom line response - tough. Product is no longer produced, replacement parts no longer in stock - maybe there is a part on eBay ** Honest that is the answer. I have called parts companies who also complain about Dacor (now Samsung). No luck. So we will now need to purchase a replacement product for anywhere from 4,000 to 10,000 dollars. To replace a 5 year old - 8,000 product. It will definitely not be a Dacor or Samsung product. And I will do my best to put similar reviews on the internet where ever I can.Just to add some balance - 21 years ago we custom built a home and purchased two Dacor ovens. Both were great. 21 years of flawless operation. When we saw this oven as we went through the home purchase process we were delighted. What a disappointment. Also - before the oven started to go wacky on us we needed to replace the bulbs (2) in the oven light fixture. Initially I contacted Dacor parts and had a very pleasant experience ordering the two replacements. However nothing came to our home. Called again and found that Dacor had been sold to Samsung and the price of the bulbs had doubled or more. No exaggeration. Stay away from Dacor and Samsung.

We purchased a Dacor dual fuel oven range in 2008 in conjunction with an extensive kitchen remodel. It was beautiful and expensive. It has had innumerable problems. 2008: One of the igniters broke requiring replacement. 2014: oven stopped working, required new relay board. June 2020: Relay board again broke, oven stopped working. December 2020: Oven stopped working, heating element broke. These were serious problems each resulting in 1-2 months without an oven as the parts had to be special ordered. We have not had an oven since December 2020 (it is now March 2021). We are waiting for a replacement part. In addition, minor problems included a broken indicator light and burner grating. Dacor customer service was only moderately helpful, referring us to local repair companies that had difficulty obtaining parts. Dacor has told us that this should last decades but we are seriously considering replacing it after 12 years because it is very unreliable. I would not recommend a Dacor based on our experience.

We used a new Dacor range vent only to have it go on and off. We called Dacor and they referred us to Desert Tech in La Quinta. The owner came out and said we needed a new unit for $775. We said just unplug it. He charged us $275 even though it took him less than 30 minutes. Stay away from Dacor AND Desert Tech!

We did a total kitchen remodel and purchased Dacor appliances. Big mistake. Had to spend 500 on refrigerator repair (model EF36BNDFSS). Oven is off 25 degrees on temperature. The glass top for burners was defective. Would never purchase Dacor. Microwave front trim keeps coming off as well.

I have owned a Dacor microwave for about seven years and is so far the best microwave Ive ever owned. It works great every time, has great preset features and also has a great sophisticated look. I would recommend Dacor appliances based on my experience with this microwave.

I have a Dacor MORS130SS oven that I purchased in July of 2008. After 6 months the first membrane panel failed, one year later the second membrane failed. One year later the third membrane failed. Im on the fourth membrane and now my fine Dacor is burning things!! I can set the temp to 350 and it shows 350 on the display but the lower element never shuts off and whatever I cook gets burned. I bought this oven thinking it might be my last considering the supposed quality of Dacor. I know for sure it wont be my last oven!! I sell appliances and I never recommend Dacor ovens because of all the continued problems. Ive never used the self clean feature since being told by a Dacor tech trainer that he didnt recommend using self clean because it would cause the oven to age faster. Wonder how long it would have lasted if I did use self clean? Sure wish Dacor would contact me for a testimonial!

In 2001, I bought a Dacor dual range stove. I paid over $2000. My problem is that there is a defect in the product; when you use the self-cleaning, the outside of the stove cracks up. Dacor has replaced this three times and each time it cracks again. I spoke with them about a year ago and because I didnt continue the warranty, they wouldnt replace it. I carry a home warranty.My stove looks like it came from the junkyard. I understand them not repairing a physical problem with the stove but the outside is crumbling because of a defect in their product. If you dont clean the oven, then you get an error and the only way to get it off is to clean but all that dose causes the outside to crack up more. It pains me to think of buying a new range when I thought I had done my homework, when I choose Dacor. I hope this isnt too late, but it pains me to think after another cleaning I may be forced to buy another stove.

I purchased my 30 range and was so excited! Well no longer. First the wrong range was delivered. I had to wait another three weeks for the correct one. My oven can not cook at all. Temp fluctuates by 100 degrees. Going on my third service call and still not working. It very unfair, I have to take time off work to wait for repair person, then nothing is fixed. I wish I could return this lemon. But after reading other reviews I am not alone. Why is this company not accountable for ripping hard working people off. I love cooking. Its my passion. My Kenmore Elite was half the price and far more superior.

I purchased a Dacor Renaissance range for our new home. What a waste of money. Though I have not had any major problems with the performance of the range yet, besides uneven baking, the design is not user-friendly. To begin with, the gas burners share a grate. So when cleaning, you have to remove the whole grate on one side. The controls for the burners & griddle are very hard to see & I have to bend over to see which burner Im turning on. The oven racks are a joke. The two glide racks are very bulky with sharp edges. It is difficult to change the heights or to remove them for cleaning purposes. Though there are three racks included, it is impossible to bake with all three in the oven.I have a GE Monogram that I had purchased two years ago for another home, and I love it The Renaissance & Monogram are similar in price, but I unfortunately, listened to the sales person & let them talk me into the Renaissance. I realized my mistake in buying a Dacor immediately & contacted the appliance store. Even though the Renaissance had not been used, they would only give me a token amount of money towards trading it in for a Monogram. So, I am stuck with a range that causes me to swear under my breath every time I use it. Dacor could learn a lot from GE.

DONT recommend model #MOH130. We were so impressed with the options that this oven came with. Sadly, with all the bells and whistles also came a ton of repairs. After the 4th repair, our service rep said the relay board needed to be switched out. (Half of the service men who came to my house seemed to be grasping at straws trying to come up with an explanation why the temperature was fluctuating, or why it took so long to heat up, etc.) Then I get to wait 2 weeks for a part to be ordered/arrived and re-schedule service. Last week got code U22 - oven wont even turn on. This oven is only 6 years old. NO THANKS - NEVER AGAIN will I buy anything from this company.

I remodeled a kitchen in a high end house and so wanted nice appliances. I had KitchenAid (which Id had a lot of issues with) for about 16 years. (Since I built the house - the fridge was rebuilt 3 times.) While looking for which appliances to use we were at an open house and a chef was cooking and giving a talk on the Dacor ovens in it. So... I reviewed a lot, liked what I read, and chose Dacor. I love them, the cook quality, the features, all of it. BUT my double oven had issues from the start. An annoyance at first with the built in Android but I didnt complain a lot. Move forward 1.5 years and the Android tablet built into it would freeze and not restart without throwing a jumper on fuse box. I called Dacor and they gave me a number of options, disable the Android because of a known issue and get $500 back, or - return the oven for full credit and theyd pay to have it removed (1.5 years later... cmon thats pretty awesome), or - pay $500 and move to the newest higher end model with steam cooking. Wow, talk about stand by your product! Ive never seen this before with an appliance manufacturer/vendor. Certainly wasnt my experience with KitchenAid. Anyway Im an advocate even though I had a problem and thought they deserved credit here.

As I have read in most of the reviews, we have also experienced the control panel on our 30 inch dual range cracking over the years. We were told not to replace it because it would continue to happen. Ok, lived with that... Now something new has started to happen, the plastic handle on the oven door and surrounding area has started to melt. It got so bad after a self clean that it is collapsing. Now there isn’t much of a seal at all when the door closes. The stove isn’t brand new, but this has to be a fire hazard, and consequently, now the oven will not even turn on. I’ve reached out to Dacor with no response yet. I’m done with this company!