With only 23 months of use, two of your KitchenAid products have failed. One, an Architect series refrigerator, quit and we were told the replacement part would not be available until January of 2020 (not typo). They had only 3 rebuilt computer control boards in the country and agreed to send one with a promise to return my bad one. Done. Now my Architect series oven/ microwave unit has been out since January of 2015. The service company they recommended has been out four times replacing parts they suggested and sent to them, with me only paying the service fees, and it still does not work. The tech department says they do not know how to fix it. They say to replace it. I have been offered a replacement for the small sum of $1,800 for a $3,650 unit I was able to use for 2 years and is not repairable now. It has an internal communication problem, code F6E0. Why would I buy another unit from a company that cannot repair what they sell. Take 5 minutes and Google error code F6E0, there are hundreds of complaints about the same code in all Whirlpool and KitchenAid brands and none have been repaired. Every appliance I have is KitchenAid, never will I buy another nor would I ever recommend them. I plan to post this notice everywhere I see KitchenAid or Whirlpool listed. Before anyone buys from Whirlpool or any of their brands, Google this error code first.

KitchenAid range KDRU783 - This stove has been a nightmare. First, the right-hand front burner was burning with an irregular, bright yellow flame. Called repair; their assessment Lady, you just need to use a bigger pot. (Pardon me, Im a chemist by training, I know incomplete combustion when I see it.) Called again, no better luck; spent several years putting up with carbon deposits on my pots. Finally, the burner became unusable; it literally burst into flame and sent up black smoke. This time I called the repair from the store where I bought it -- a well-known chain -- and they sent a technician who spent time investigating. Found the problem -- a connection to the propane line had come loose. Then, an additional problem occurred: the touch panel would start clicking when we used the left-hand front burners. It would flash on and off at 350 degrees, or 500 degrees, or some other setting but would NOT turn off. At worse, the entire stove -- both ovens -- would become inoperable. This second problem resulted in 3 trips by the repair people, who replaced the unit twice and then a third time with no change. However, the 3rd set of technicians think they have figured out whats going wrong -- and I have an appointment the day before Christmas, thank you very much. Right after they left, a third problem occurred: the left hand back burner next to the griddle keeps sending sparks; we have checked that one of the covers on the burners might be off center, but thats not the case. The result is that the only way we can stop the sparking is to keep the burner turned on low (so that we can use the other burners and the ovens) or to turn off the circuit breaker. I would like to hear from other people who have this range and find out whether this might be a common defect.

I have been disappointed in my refrigerator from day one. Temperature is inconsistent throughout: items freeze and also, just simple design features, like being able to open a vegetable bin when only one door was open, but now taking the cake is my ice and water on the door only functions intermittently and service guys said needs a new board. It’s a $250 part, ok. Frig is 10 years old, I’m ok with that. WELL THEY DONT MAKE PART any longer and there is no work around! KitchenAid customer service’s best response was to send me to a discount supplier of new refrigerators. I’m beyond frustrated. They blame it on supplier, but we all know if KA cared enough for their consumers, it would be provided. This was an expensive refrigerator and I don’t want a new one!

We bought a whole suite of KitchenAid large appliances (from Fergusons) for our new home build. We have been very satisfied with the performance of all - UNTIL the dishwasher tore up. It was still under the factory warranty. We called the issue in and there was a local company (American Appliance) that arrived 3 weeks later to repair. They discovered that the heating element of the dishwasher was broken and needed to be replaced. They ordered the part. They said it should arrive in 7-10 business days. After that amount of time, I called to be told that it was on backorder. They didnt have any clue of when the part would be back in stock. Therefore, we started reaching out to KitchenAid directly.We have spent over 6+ hours trying to reach KitchenAid and to speak to their technical department, parts department, warranty group, and finally complaint group. We have been told multiple things - there was a recall on the part (cant confirm that one), the part was out of stock and would not be in stock until after December 30 (totally unacceptable), and that the part was finally now in stock. We were told on July 8 that the part would go out to us on a truck the next day. Apparently that didnt happen. We have been on the phone with KitchenAid complaints again today for over 1.5 hours (more time) to be told that the part has been ordered but has not been pulled and shipped yet and that it would take another 2-3 weeks for that to happen.We made the choice to buy Kitchenaid (Whirlpool) appliances for our new house because they are American made and felt that they would stand behind their products. We are so dissapointed in how this has been handled. We are going to be without our dishwasher for at least 2+ months (and we are a family of 6 people). Our disappointment comes from both the quality of the part but even more importantly the way we have been treated and the repair handled once it tore up. I would not recommend them today. I would be cautious because if you have issues it is not an easy road to travel! Our warranty has not been very effective up to this point.

We purchased a new KitchenAid KSC23C8EYY for $2600 at the end of Jan. The ice maker didnt make ice for the first 48 hours and then the water started coming on but not shutting off. This happened at night so we didnt notice it until the morning. This filled the freezer with a frozen waterfall of ice and spewed water all over my new kitchen floor and under the new dishwasher. I called Western Appliance to have them replace it since it was brand new and now was covered with ice. They had to send a tech out before they could/would do anything. So I waited 2 days and the tech said a valve was bad. They had to order it. Western Appliance finally agreed after much angry conversation to replace the refrigerator which they had to order. That was another 3 days. Now, 2 months later, the water dispenser and ice maker stopped working. The first tech from A&E that came out had to call Whirlpool service and they recommended that he replace the wiring harness that he had to order, 10 more days! The second tech from A&E that came out said it wasnt the wiring harness and found that the coil inside the refrigerator was iced over. He said to unplug it for 24 hours and it would fix everything. He said that we had left the door open and that was what started the whole thing. Well, this refrigerator door slams shut if you leave it anything less than 90 degrees open, so it is not at all possible that we left the door open. I told the tech that he needed to find the problem that was underlying the frozen coil before I would agree to unplug the refrigerator for 24 hours thawing out all of my food. He said that was what the Whirlpool Service Center was recommending.I called KitchenAid service again and explained my concern and told them they still needed to fix the problem. They agreed to send out another service company. J&H came prepared. They brought their own towels, a cup to test the water dispenser, a floor protector, and a steam generator to defrost the coil. Yipee, someone who actually knows what they are doing! They diagnosed that the two thermistors that defrost the refrigerator and freezer were drawing different voltages. They are ordering parts and should have them in 3 days. Hopefully this fixes the problem. Im not sure that I would go the KitchenAid route again. But I understand that Whirlpool makes KitchenAid, Kenmore, and a few other refrigerators so I dont know how you get a refrigerator that wont have the same problem. I also understand that Samsung and LG have way more issues from the 5 technicians that I have talked to in trying to get a working unit.It seems like a lot of money for something that has had this amount of problems in the first 3 months of purchase. I guess this just reaffirms the old adage, Buyer beware! It sucks!

Purchased this unit in 2010 with an extended warranty. The unit died in 2012 and was able to get it replaced because of the extended warranty. However an extended warranty was not offered to me on the replacement. The replacement was installed in November 2012 and failed to heat anything in 2015, approximately 2 1/2 years old. I called KitchenAid and spoke with their representative in Tennessee, I explained that this was the second microwave that failed in a two year timeframe. The lady was not very helpful. All she wanted to do was sell me a warranty or I could pay to have a technician come out and look at it. She advised me complaints on defective manufacturing are based on Service Technician calls since they did not have any for this Model then there is nothing wrong with it. I asked her why would 2 of the same units fail during the same time frame and KitchenAid would not recognize that something is wrong with the unit. I told her I could buy a microwave for less than $100.00 and it would last longer than this model. She told me I should have bought an extended warranty. Apparently I am to blame because I did not get an extended warranty from them for $329.00. At this point she stopped listening to my questions and proceeded in a very loud voice which can be heard clearly from 3 feet away that KitchenAid stands behind their product and there is nothing wrong with that Model microwave because there have not been any complaints. I told her to search the internet. If KitchenAid sold quality products and stand behind their products why would there be a need for an extended warranty. Very, very poor customer service. Therefore if you buy a KitchenAid appliance buy a very long extended warranty because their items are not cheap and the warranty is not cheap also.

I bought a KitchenAid DW and am very dismayed by the lack of information regarding this bizarre drain line. I have installed several dishwashers before and never had any issues as this. The drain line seems to be long enough if you could unravel it from their mountings on the side of the unit, which apparently are not to be removed? I still have no clue. I had to butt together 2 drain lines with a 3/4 nipple and 2 hose clamps to connect the 2 soft ended hoses together, seems wrong but impossible to get any facts. Some say remove the hose from its bindings, which looks impossible to do safely, or butt connect 2 hoses jury rigging it like some Ethiopian setup, not happy!

I filled out a complaint on 10/11/11. The repairman was at my house and replaced the motor on my 7-month-old dishwasher after waiting 3 weeks to get it repaired. It is now 10/21/11 and it broke again today. It was the same problem as last time, so I assume it needs a new motor again. I have to wait another 12 days just to get a service person to come out and look at it. Ill then be at over a month with a non-working brand new dishwasher in a 7-month period.

At 1 year, the rivets that hold the sliding rails for the top rack rusted out and the rails fell off. I believe the new rails were almost $40 each and I had to pull the dishwasher out to replace them. Then about 6 months later, the wheels for the bottom rack started falling off one by one until over the course of about 3 months the bottom rack is wheeless. Ive just order 4 packs of wheels for another $30. The dishes no longer get very clean.... Ill never buy any Kitchen Aid product again.

We have been dedicated KitchenAid fans for two decades. Two years ago, we renovated our kitchen and purchased brand new KitchenAid Stainless Steel Appliances. Within ONE year, the side-by-side refrigerators ice maker motor died. Through the warranty, a new motor was installed. Recently, the Freezer component that generates Freon died. KitchenAid Extended warranty was incompetent and arguable. Finally, after THREE weeks, our freezer was repaired. However, our refrigerator stopped working. KA Extended Warranty offered a repair man in 9-12 days. I cancelled the KA Extended Warranty contract, hired my own appliance doctor, and within 5 hours it was fixed (the previous tech did not plug-in the valve to the refrigerator!). Poor product and even poorer service through the extended warranty.

Very, very quiet. Stainless steel interior. Does an excellent job of cleaning dishes. The only issue I have had is that a seal on the bottom of the door leaked when new and it had to be replaced under warranty. Now, a few years later, that seal began to leak again but I was able to clean and re-position it and it works fine now. They needed a better design for that seal.

I too experienced the dishwasher top rack roller failure. The top rack rollers are secured by (2) cheap very thin plastic spreader clips. These clips are approximately 3/16 wide by 1/16 thick. If just one of these cheap clips breaks - the roller wheel will separate causing the rack to collapse along with progressive failure of the adjoining roller wheel clips. This deliberate design and manufacturing defect by KitchenAid is an obvious attempt at planned obsolesce. This once celebrated company is no longer interested in producing durable quality products. Avoid the purchase of all KitchenAid dishwashers!

The interior shell has numerous cracks. The repair technician said it is common with KitchenAid refrigerators. The refrigerator is only five years old. It has Superba stainless steel side by side for over $2,000.00, and it was paid for new. I never had any refrigerator or have ever heard of this happening before. The manufacturing defect is the only reason this is happening to these units. Has the government done anything yet to protect consumers against this type of inaction by the company?

Just had our 2 day old oven door shatter. We replaced a 1982 wall oven this week with a KitchenAid wall oven, model KOSE507ESS. It was installed yesterday. Tonight was the first time using the oven. I was preheating it to 400 degrees when I heard a loud pop and then glass was flying out of the bottom. The inside glass window shattered and glass is everywhere. I will be calling our appliance store first thing tomorrow morning. At the moment, no other damage has occurred to anything else other than the oven. I just want it fixed.

The very first time I utilized the self-cleaning feature of my oven, the screen went completely black (never to come back) and the door would not unlock. First thing I did was google the problem and it looks like Im not the only one that has encountered this, and that is an understatement. There were literally hundreds of accounts of the same thing happening. I contacted Kitchenaid and they told me that there has not been a recall on my range (model KGSA906PSS00) and that there was no known problem...really?? The best part was that the replacement part is almost $400 and they would gladly transfer me to the parts department to purchase it. Thank you for the help.

The issue I am currently having is trying to get a new control panel for our built in refrigerator. The day after Christmas the refrigerator went out. The following Monday I called a local appliance repair business so we could get the refrigerator fixed. They showed up the following day and informed us it was the main control panel that was out and this part was not available. They suggested we either were going to have to have the control panel rebuilt or if that did not work the only solution was to buy another refrigerator. I found that hard to believe so I called KitchenAid and eventually got to the Built-In Department. I was told the part was getting ready to be available and would be ready for distribution on 1-7-16. Was also told until now this part had not been available due to the manufacturer being destroyed in a storm and it had taken them several years to redesign a part that actually worked. I also found that hard to believe. However, I now thought all issues were taken care of and excepted the wait. Well, yesterday I decided to call checking on things only to find the part did not go out as stated and there was still (0) showing in their availability. The parts distribution company that our repair shop orders their product from had not even placed an order because there was still 0 showing available. After several phone calls and talking to several different people my frustrations only grew. It appears that even though the folks in the built in department could see the inventory was available nobody was able to order the part because the part is still not showing up as available in their system. Finally, the part was made available for me to order, shipping at my expense, to be shipped to my repair Co. I also then found out that I would then be responsible for shipping the core back and that I would have NO warranty on a $350.00 part. If the part was ordered through my repair Co I have a warranty and no shipping expense. They were not even willing to ship next day or 2nd day mail. For a part this expensive and with as many issues it appears there have been with it, I decided I needed the warranty so Im back at the mercy of KitchenAid and the wholesale part supplier to get the part to my repair Co. I found the policies at KitchenAid and the procedure they go through to be very non-flexible and not consumer friendly. In addition, we put all KitchenAid products with the exception of our gas stove in our house. We have already replaced the built in Ice maker and the microwave. This will be the last KitchenAid/whirlpool appliance we ever purchase.

Worst fridge ever. All the shelves are broken on the plastic edges. Basically, the plastic parts crumble after a few months. We have replaced them and they broke again. The ice maker has never dispensed ice properly. My sister has the exact same experience with her KitchenAid fridge. We both paid a lot of money for these fridges. Run away from KitchenAid fridges!

All the inside drawers are cheap plastic and the front piece broke after a year. It’s over 100 bucks per drawer to replace and you have to replace the whole piece. All the appliances I have even the dishwasher rack broke. Too expensive to buy and doesn’t last.

This dishwasher was purchased at Lows. It is a KUDS30IXSS1. The serial number is F10101981. They sent me a warranty expiration notice, it expires 2/25/2012. I wouldnt spend one more dime on this.Dishes have to be prewashed before loading them in dishwasher. Everything come out filthy after they are washed. Everything has a dingy film over it. I always wonder if we are going to get sick eating off the dishes. The dishwasher takes way too long to run the cycle. If you dont use the heat dry the dishes dont dry at all. All of my black cooking utensils are so discolored. I have been throwing them away and replacing them. My old Whirlpool did a wonderful job on the dishes and it cost about half of what this one did. It was about 5 yrs old and I gave it to my Mother-in-law. The only thing I can say about this Kitchenaid that I like is it is very quiet. I wish I could afford to get rid of this thing. I would sent it to good will and recoup a little of my money at least as a donation.

Worked with a parts person at Whirlpool who located a control board for my oven. The suppliers were saying another week or two and then only maybe, but she found one at a distributor and is having it shipped to me. Very satisfied with her work but still would never pay for KitchenAid again.

While preheating, the inner glass of my KitchenAid wall oven exploded. KitchenAid was of no help even with the purchase of an extended warranty.

I am a single mom who worked hard to purchase the gas range of my dreams. But ever since I bought this range it has been one nightmare after another. The oven glass shattered on its own one day when I was sitting in the kitchen having my coffee; the gas leaks every time I turn on the top oven; the knobs constantly break and have to be replaced every two years. Sometimes I really think this range is possessed! Possessed or not, this range is a hazard that I need to get rid of very quickly. If you are considering purchasing one of these ranges, think again. By far the worst decision my life.

On 12/28/10, I purchased a KitchenAid fridge, model kscs25fvms, for over $2000. One year later, it started making a loud mechanic noise. When I got home from work, it had stopped cooling. Time to buy ice coolers and ice. The repairman came out and stated that the compressor had failed. After numerous emails to KitchenAid, not one response. The bottom line is that they dont care about the customers. Its the mighty dollar they are after. Please, I beg of you, dont purchase any KitchenAid or Whirlpool products. They are defective. No quality product should fail after one year of service. Try a Japanese or German product. You should have better luck with them.

An unusual problem occurred with my 1999 refrigerator. A screw broke inside one of the back wall brackets that hold the shelves. I called KitchenAid for an authorized factory dealer thinking their experience would know how to resolve the problem. KitchenAid informed me the cost to send someone would be $129 plus parts, and if the tech stated it could not be repaired, they would offer something towards the purchase of a new refrigerator. The tech was not able to get the broken screw out of the bracket. I called KitchenAid in his presence, and they refused to stand by their original statement. The tech called his employer, A&E Service Co. and was told to do the best he could. He claims he inserted another screw near the broken one and put tape across the top and bottom of the bracket to hold it. He said this is a temporary repair that might last 3 months and then I would have to buy a new refrigerator. A&E charged me $166.20. I complained stating that wasnt the quote I received, and the tech was not able to fix the problem. They said they will reimburse me $26. I feel because the refrigerator was not able to be repaired, I should be reimbursed the full amount (A&E Factory Service, 35 Melville Park Rd, Melville, NY 11747, tel.# 800-905-9605). The tech arrived on January 7. I spoke to KitchenAids repair department, customer service, and the sales department stating what I was initially told about partial compensation towards a new refrigerator. Each department refused based on the year of the appliance. This is a very unusual matter. The tech noticed only very light items are placed on the 2 shelves involved. He said he never saw anything like this in all his time as a repair person. He noted it wasnt weight that caused the bracket to separate from the back wall. Am I entitled to a full reimbursement from A&E since they could not fix the refrigerator and I will eventually have to buy a new one? Is KitchenAid responsible in any way?

I purchased a Kitchen Aid two-drawer dishwasher in 2009. This has been the biggest problem appliance I have ever purchased. I am glad I paid for the extended warranty because the techs have been out every 90 days maybe more and they know my address for the same problem that keeps happening. It is the Bizel that are located in the top and bottom drawers, that continue to break... AND when they do if the dishwasher is not monitored, it causes water to leak all over my hardwood floors that are ruining them. The warranty company informed me that if it is not a major component, they will not replace the unit. Obviously, this is a major component as if this component breaks you cannot run the dishwasher?? So, how can Kitchen Aid determine that this is not a major component. This was an expensive dishwasher and also you cannot fit any regular sized plates because they do not fit...so we have to eat off of appetizer plates. I will never buy a Kitchen Aid appliance ever again. Kitchen Aid needs to resolve this problem or I am taking this issue to attorneys that I work for. One really unhappy Kitchen Customer!

I purchased a KitchenAid 42 Built-In refrigerator through Western Appliances (located at 1976, W San Carlos Street, San Jose, CA 95128). Within 1 year the right door would pop open after closing. I called Western Appliance first and they said they can’t do anything and I should call KitchenAid directly. I called kitchen-aid and they sent service technician, but it didnt fix the problem. In last 1 year they have sent service technicians almost 6 times and the problem still persists. After paying $8389.31 I am using a duct tape to keep the door closed, otherwise the food will go bad.I would like to get either my money back or product exchanged for a good one. Customer service said that they have sent my compliant to Pex department, but they didn’t give me any assurance on when it would be replaced. For last 1 year I am tired of calling them, getting a service scheduled and then staying home from work for the service technician to come home. They have changed hinges, they have even changed the door, but the door still pops open within seconds after closing. Here are more details on the fridge. Model Number: KBFN502ESS Serial Number: **Purchase Date: 02/14/2018

We purchased a high end KitchenAid refrigerator (almost 3,000) and began having problems within 6 months. Have had 6 technician visits to attempt to fix (back of refrigerator freezes up, cant get filtered water, stops cooling and food rots in our absence). EVERY replaceable part that is not considered part of the inner compartment has been replaced. Our last technician, in writing, wrote that there was nothing else that could be done except replace the entire refrigerator and that ours was a lemon. I called the manufacturer (Whirlpool/KitchenAid) and they told me that I had a problem and they didnt, in other words... I was SOL. DO NOT BUY A KITCHENAID REFRIGERATOR or for that matter ANYTHING under the WHIRLPOOL umbrella since they will not stand by their products. Buy a GE!

My KRFC704FPS Counter-Depth refrigerator has had issues since day one. I should have returned in within the 15 day window to Best Buy. It is super noisy and can be heard as far away as the 2nd floor of my home. The freezer temp wont go any higher than -7 degrees on a thermometer and that is with a setting of 5 degrees. I have a super accurate electronic thermometer in the freezer and it can get as low as -20 degrees. If I set it lower than 5 it can get colder. The refrigerator section has to stay at 39 degrees of food starts freezing. KA has been out 3 times for the issue and they wont help. The techs even brought their own thermometers and it states the same. Their only fix is to turn off the ice maker. I paid $4k for a refrigerator and they wont stand behind it. Also, the seal is tearing and water pools up and freezes in the bottom of the freezer. I have had it for 11 months. Every time the tech comes out he says there are issues, but KA wont do anything but say it is normal. I have all KA appliances too.

Just had my 6th service call in a year and a half to repair the ice maker. Because its now out of warranty every call is costing me $99.95 plus parts and labor. This is a $3000 refrigerator and works far worse than the $600 one in my garage. KitchenAid refuses to do anything to assist so I am pursuing lemon laws.

Last summer, my KitchenAid Refrigerator (not a year old) stopped working. After two months of repairmen being sent by KitchenAid (A and E Services) and numerous ordering of wrong parts, the refrigerator was repaired (or so I thought). Now this week, the control board does not work. A repairman came, and after two hours, the refrigerator still is not fixed. The required parts are supposed to come and be installed next Saturday. I paid over $2,500.00 for my KitchenAid refrigerator/freezer, and I have been totally dissatisfied with this appliance. I will never buy a KitchenAid product again. The KitchenAid representatives seem to lack any concern for this problem.

We have now had eleven service calls with the tech here up to three hours a call. The control panel has been replaced three times. The key board once. The sensor once. The temperature still goes from 325 degrees to 386 degrees after preheating two cycles. The bottom door hinges have been replaced twice with no change. Door still does not close properly resulting in bottom element not coming on. Whirlpool says this is all acceptable. For a supposed top of line stove, one should be able to bake without burning or undercooking. The manual says the oven temperatures are accurate. Not so!!

We purchased four KitchenAid items for our kitchen to receive a $600 rebate. Our reseller showed us the KitchenAid screen where all items were available for deliver in less than 30 days. This was a condition of our purchase. That was 04/01/2021. They delivered our oven and microwave and dishwasher. They never delivered our refridge nor wine cooler. They now claim end of the year. Our sales rep indicates maybe even later since the manufacturer reps come and go and KitchenAid changes its mind on deliveries. I called them and asked if we could pay a little more and pick them up IN STOCK at Best Buy and still get our $600 rebate. They refused. They are making us wait for an unreliable delivery date. They misrepresented the purchase. I saw the manufactures computer screen that said they would deliver. DO NOT BUY from whirlpool or KitchenAid since they will rob from you and not give you any rebates. In addition, they will not live up to their delivery dates even on their own computer system.

We have a KitchenAid KHMC1857WSS--0. We purchased it on 1-29-10; it was delivered on 2-14-10. It first quit working last 12-29-10. I was using the Convect Roast, auto mode, pizza, when it went out very near the end of the cook time; about 15 minutes into the cycle, it blew the fuse. We called and they scheduled service for 1-3-11. They replaced the fuse and said it worked. On 1-18-11, it broke down again in the same mode. Service was scheduled for 1-20-11. They replaced the fuse and some other part, and they offered to extend the service warranty for one year. Good thing, cause it broke again and was serviced on 2-3-11. I asked for a replacement microwave; they dont want to do it, saying that it is more than a year old and is not covered. It broke again and was serviced on 3-7-11. After much complaining, they agree to offer us a microwave replacement for $300. The new microwave was installed on 3-30-11. For some reason, I thought this would fix our problem. But we have the exact same problem on our new microwave. It was first serviced on 10-5-11. They came back on the 13th to put in the new parts, and the service man declared it fixed. I ask that he run it in the pizza mode before he leaves. Guess what, it blows the fuse again. He called it in, and they want to put in another new part.I am fed up. I want a microwave that works. I paid about $1000 for a new one and then paid $300 for a replacement, and I still have junk. The only offer from KA is to continue to service it. I want my money back for the replacement and a microwave that works for more than a month without breaking. KitchenAid will not stand behind their product and has done nothing but steal money from me.

I called KitchenAid and contacted the repair guy. He came and said he needed to get parts. Week passed. Meanwhile, our contractor had come and fitted the refrigerator with the custom panels to match our new cabinets. Then the repair guy came with 1 of 2 possible bad parts, opened the box and part was broken. I found out from him that the other part - the main circuit board - was made by some factory in Japan that was wiped out by the tsunami. KitchenAid has no replacement parts for this board. If it is bad, it has to be pulled and sent back to KitchenAid to be repaired. However, repair guy said, We should replace the control panel board first and see if that does the trick.I called again to KitchenAid and had the part shipped to our home to expedite the repair - another week passed before we could get the repair guy back (we live in the country) and he opened the box (part number of the box was right) and said the part that was sent to us was for a stove. That was today.We have now been over a month with nothing but a mini-refrigerator - KitchenAid has been unresponsive and uninterested in helping us. We have now contacted both the place we bought this turkey from and have agreed to wait until Monday for the sales person to contact KitchenAid and see if he can get a replacement (which we are pretty much boxed into, as we have a big investment in the custom cabinet arrangement).Im SO disappointed and frustrated.

KUPD02CRBL3 Dishwasher starts and after a few minutes the door pops open and it stops... Sometimes when I clean residue near bottom of the door or keep object away from vent in upper left of door, it will run. Unit is 7 yrs old. It has great capacity, is quiet and cleans well... just would like to know what the heck is going on with the door.Updated on 09/25/2015: I used the diagnostic to reset maintenance cycle that was located on the backside of the bottom plate of the dishwasher. So far its working well. Hope this helps everyone... also going to clean out area inside under spray wand to make sure there is nothing in pump area.

Since Whirlpool stock is way up in price, might be a good time to sell...or short the stock...After owning Maytag for 4 years and having a manufacturers defect they made me an offer I could not refuse and I bought a new top-of-the-line KitchenAid dishwasher on 6/2013. I am real happy with the performance. Its quiet... cleans great so far. The bad news is that a thousand dollar dishwasher should not have such a poorly designed upper basket. The wheels just broke and several expensive pieces of glassware fell out and broke. Ask me if I am angry...LOL. After reading the many complaints on the design and quality of the parts used and that most have experienced the same problem I urge everyone to call Whirlpool corp. at Corporate Office Headquarters HQ: Address: 2000 N. M-63, Benton Harbor, Michigan 49022-2692 USA, Corporate Phone Number: 1-269-923-5000, and ask for the Office of the President and complain. The cost of repair with service is over a 150.00 but if youre handy you can fix it better than new for under $2.00.

We paid a lot of money for this dishwasher. I had high expectations which were not met. Do not be fooled. A name does not mean a guaranteed quality product. The door malfunctioned after just a few months and now the dishwasher smells terrible as it doesnt clean like its supposed to. Why have a dishwasher if you have to scrub every dish before putting it in the dishwasher? Thats a waste of my valuable time. Research your purchase! Dont buy it for the name only. Youll be disappointed.

04/06/2018 - Purchased french door refrigerator (KRFF507E). 09/30/2019 - First repair. Refer making noise and not cooling. Evap fan hitting ice buildup Tech replaced evap fan and thermistor assembly (took over an hour to remove ice build up). Tech also reprogrammed defrost cycle from auto-detect to every 8 hours.02/19/2020 - Second repair. Same problem as first repair except evap fan not destroyed. Contacted KitchenAid service basic response was too bad, so sad. I explained that the problem was a design flaw, not a faulty part problem but that fell on deaf ears. After a bit of debate service stated that replacement parts (from 2/2019) were under warranty. Service tech ended up replacing same parts and a control board. Again, over an hour to remove ice buildup. 08/08/2020 - Third repair scheduled for 8/17/2020. Sour milk, refrigerator temperature running about 57 degrees F. Ice buildup again, waiting for Tech to diagnose. Again KA Service response was too bad, so sad. Service authorized a $50 reimbursement card, which covers about half of technician service charge (not parts).The refrigerator was purchased to replacing an ancient (15 yr+) kitchenaid side-by-side refrigerator/freezer that is still keeping my beer cool and my deer meat frozen! I will never purchase a kitchenaid refrigerator again (maybe anything from Whirlpool).

Today I phoned for my 4th service call for this 2 year old KitchenAid dishwasher KUDS30FXSS. It simply doesnt clean the dishes, leaving a food residue on mainly the top rack of dishes. Each time, the serviceman has cleaned out the chopper and pump (beware: there is no removable filter for this model) and it cleans for a few weeks, then we start washing by hand until I can find a time to stay home for another service person to come out to do the same thing. Even though I purchased the 4 year extended warranty, KitchenAid has denied this 4th claim. I have been a loyal KitchenAid customer, and will be replacing this dishwasher with different brand. What a waste of money and resources.

We did a total kitchen remodel and included a dishwashing machine, which the house never had before. We sprung for the higher end stainless steel tub KitchenAid KDFE104DSS1 (2016). 3 months later the machine stopped moving water, but could still drain. Warranty phone call... repair tech does two visits... one for diagnosis and one for part install (new pump). Up and running. 5 months later same deal. Another warranty call and two visits... back up and running. Now I notice the rusting slide rails for the upper deck. Now into the out of warranty mode and the pump fails again.Going shopping today for a cheaper machine... putting the KitchenAid trash out on the curb for the recycle guy. BTW there were intermittent events for soap dispenser door not opening. (No dishes in the way.) Food pieces splashed around hanging on the walls... and then theres the smell. This model likes to hold used water between washes and after just one day of no use, OMG what a stank.

KitchenAid dishwasher model KUDS02FRSS2 - We bought this dishwasher from a local distributor to the trade for more than $1100 in September 2006 and now, in less than 6.5 years, the control panel has stopped working. I tried all the suggestions in the manual and that customer service recommended without results. We set up a service appointment with a KitchenAid certified repair firm with a ridiculous $150 appointment charge. The tech tried to run diagnostics on it with no apparent success and just came back with a, It looks like you need a new control panel! Of course, he tried to sell me a $300+ extended warranty, in case anything else goes wrong. For just $430, I could have my gently used (run less than once a week in its life) $1200 dishwasher back in use. This unit was installed with our kitchen remodel when we also bought KitchenAid cabinet-depth refrigerator, dual fuel range, microwave and dishwasher, $7500 in what we thought were premium appliances. Im pissed at the lack of customer service support and, based on what I read here, are significant quality issues with KitchenAid dishwashers and a company focused more on selling extended warranties. Im a very dissatisfied customer.

KitchenAid Model No. KDRP467K 36 Architect Series Dual-Fuel Range. The rotary control was set to bake at 350 degrees F. At 12:30PM, I placed oatmeal cookies on a cookie sheet (metal) into the oven preheated at 350 degrees F. At 12:37PM, the oven began to smoke. We checked the setting and temperature, attempting to open the oven door. It was locked and the oven was apparently in the clean mode although the controls were clearly not set to clean. I shut the power to the range off at the breaker panel. The range took two hours to cool. We have never used the self-cleaning feature.

2 years old dishwasher. Within 6 months, top rack roller axles broke. After a year, stopped cleaning top rack items. I found out the Chopper Assembly was broken. Had to replace it. Both are cheap plastic parts. Terrible experience with this brand.

Had to buy this refrigerator to fit into an existing built in space. The size fit perfectly. Only positive to our experience. DO NOT BUY this refrigerator for the following reasons: Installed in Jan 2016 and already had to replace icemaker, slides on bottom drawer dont work, seals on top french doors moldy, temperature not regulated in refrigerator, and freezer section froze up. Labor costs to repair is very high: quoted $340 to replace freezer drawer slides and around $100.00 each time someone comes out to check. Mold started accumulating on refrigerator seals. Noticed some small rust spots on the freezer door (exterior) that I could not remove. We do not overload either freezer or refrigerator and we vacuum out coils regularly. My next review will be on my Kitchenaid double ovens - very disappointed with these as well!!!

My built-in side-by-side stopped cooling almost a MONTH ago. I did call a highly rated Yelp repair company but they were honest and said that since it was still under limited warranty I should work directly with KitchenAid. Let me keep it short... Its ugly. KitchenAid is deliberately slowing down service and forcing me to work with someone who has terrible Yelp ratings. In fact I have spent $1,000 with this company and even though he claims to be able to diagnose the issues - KitchenAid tech backs him up - as of today my unit is having the same exact issue. We have replaced a heating coil that required 6 hours of labor (KitchenAid confirmed) and a compressor.I called another service company who indicated it is a simple problem that can be fixed easily. When I called KitchenAid and explained this, the customer service guy actually fought with me...refused to speak to me any further unless I gave him the phone number and name of the other company. They were so concerned that one of their authorized repair companies was questioned that they tried to intimidate me into thinking I was going to lose support. Bottom line - I asked for a supervisor and she was understanding. I begged her to send different service company but she refused.As I write this, my $12,000 refrigerator/freezer is not working, despite KitchenAid forcing me to spend $1,000 with their service person. It also still sounds like the engine from a small commercial plane, even though prior to that it was so silent. And no refrigeration still. And guess what? My service repair person will not call me back. KitchenAid is clearly trying to stall until warranty runs out. I will never buy another one of their products. To top it off, it is one of the worst customer service experiences I have ever had.

KitchenAid double gas range (model KGRS505XSS01) burner failed on arrival; knob failed after six months, not covered by warranty. (We tried to force the knob and bent the pin.) That cost $185. Another knob failed one month after warranty ran out. Estimate for same repair is $230. Stainless steel surface is stained, scratched, and discolored. I had trouble on the phone with Sears service company, A&E Services. I was on hold for an extended time as they were having technical difficulty, and eventually I got cut off. Parts available from Sears and from Whirlpool for $59 vs. $80 quoted by A&E Services.

My family bought this range as it was one of the few gas stove downdraft ranges that could be installed in the middle of an island. It is pretty in our island but it is a TERRIBLE and I mean TERRIBLE range. The oven cooks uneven so dont even thinking about trying to bake anything. Over the holiday, the only way I could get by without burning the food was to place the thickest part of the leg of lamb towards the back. Not to mention that it probably takes about 30 minutes to even get the oven to 350 degree heat. It is ridiculous that something this expensive would perform so poorly. To top this off, the self cleaning function does not work.I decided to use regular oven cleaner and that was a big mistake. Now the inside of the oven is peeling. I contacted Kitchenaid to see if it was safe to cook and their representatives are basically robots and would not provide me with an answer or anyone else who could help, they just kept repeating we dont suggest harsh oven cleaning products. I think 450 degree heat is pretty harsh, so how can an oven cleaner be worst? HUGE disappointment overall and would not recommend or ever purchase a Kitchenaid product again.

We purchased nine top-of-line KitchenAid built-in refrigerators for the premium units in a condo development. A circuit board failed on the first unit after 6 years. We replaced the circuit board (at significant expense) and the unit seemed to work fine... for awhile. Then, two more circuit boards failed in other units but this time circuit boards were not available, reportedly due to the tsunami in Japan. There was no support from KitchenAid or Standard TV & Appliance in Portland, OR - out of warranty they said. We finally found a company that rebuilt circuit boards (very expensive). One of those has since failed and we are awaiting another. Still no help from the dealer or KitchenAid. If you are buying a refrigerator, find another supplier and dealer.

This fridge is 5 years old only, and have been struggling to repair the ice maker for one whole year and no one could fix the problem. KitchenAid is not a good brand. I bought it from Pacific Sales. The rust showed inside the bucket of the ice maker since we bought it, mold created inside the fridge, bad built kind of refrigerator, very fragile drawers. Don’t you ever buy KitchenAid products, trust me I’m still struggling to repair it.

We purchased the new low profile style of KitchenAid microwave hood combination to replace a 21 year old Maytag model. I could no longer get parts for the old girl so decided to update. Installed the new unit in March of 2019. The performance of the microwave is as I expected from a higher end product. The model upgrades to LED lighting and the exhaust fan features are all pluses for this unit. The microwave touchpad and programs have worked very well. I would be rating this unit with 5 stars at this point except for one major flaw....There are (5) chrome buttons on the front face of the microwave to control the lighting, fan, open the door, cancel program, and start menu programs. On the surface of the buttons lettering had been stenciled to identify the function for each of these (5) buttons. After about 6 months of use the lettering has become faint and/or disappeared. Of course the two buttons used the most START and OPEN are now basically missing any lettering to identify the function of that button.In September I decided to contact KitchenAid Customer Experience Center about the problem. I first used the contact via e-mail found on the KitchenAid website explaining the issue with the button lettering disappearing. Received a response about 5 days later stating they were sorry I was experiencing and understood it could be frustrating. Then went on to state quote When touching the control panel, be sure there are no oils or lotion on your fingers. This can damage the lettering and finish.. They would be sure to pass on my complaint for review and future improvements. Of course this response did not sit well with me. What kitchen appliance should not stand up to normal use with your skin oils or other kitchen products touching its surfaces.I then called to arrange for a service call on the microwave again explaining to the representative my issue with missing button lettering. After much discussion of the problem they basically categorized the problem as cosmetic and therefore excluded under their warranty. The warranty in the User Guide also stipulates in bold lettering The cost of repair or replacement under these excluded circumstances shall be borne by the customer. No service call was set up at this point.After a couple more e-mail exchanges with Consumer Correspondence Team personnel, they recommended I arrange a service call to have a local KitchenAid repair technician look at my problem. I asked them to waive any costs for the service visit IF the technician could not classify the defect as anything other than what they had already called cosmetic. They could not provide me with such a waiver and no service call was arranged.I would say the Customer Experience Center personnel listened to my complaint and understood my dissatisfaction, but could not help resolve the problem. I even asked them to just send a set of new buttons and I would be a happy customer. I dont think that is going to happen either. No further communications for a couple of weeks now.Like I stated earlier, I now have (2 of 5) buttons without identification as to their function. The User Guide does not pictures of these buttons so you cannot lookup what the buttons do, good thing for our memory I guess. The frustration is the lettering should be able to withstand normal use in a kitchen environment without rubbing off. It is more than a cosmetic issue. Thus the reason for the 2-star rating for this appliance. I just want current and future customers to be aware of this issue. A photo is attached of the right hand side buttons showing the lettering disappearing with use.

Wow! I am completely dumbfounded at the incompetency and lack of customer service KitchenAid provides for warranty work... Start to finish, it has been a horrible experience and my very expensive, 3 1/2 year old fridge still isnt working. I dont even want to go into all the details because this has already wasted so much of my time. I just wished I had read all the other reviews prior to purchasing this fridge... very disappointing and I will not recommend nor purchase any more of their appliances.

My 5-year old KitchenAid dishwasher (Model: KUDP02FRSS3) pops open during run cycle. I have had 6 or 7 service calls, and none of which have fixed the problem for a few weeks or months. When working, we have good results as far as cleaning is concerned, unlike some other KitchenAid owners. I cannot count the number of times we have used a chair propped up against the door to complete a cycle. The door striker and/or latch have been replaced 3 times, while the springs and nylon cord have been replaced once.During this repair, the tech bent the hinges inward and installed a single rubber bushing on one of the hinges to increase friction with the door in the closed position. He would have installed 2, but he only had one. The door did stay closed for 2 or 3 months. Eventually, the single bushing worked its way off. Probably because the original hinge was not designed for this bushing. During my third most recent service call, the tech installed a new plastic latch. The machine would close but it would not start.I checked the CB and was advised on the phone to do a hard reset (i.e., leaving the CB off for 30 seconds or so). This did not solve the problem. When the tech returned, he was stumped by this problem. Looking at the new latch, I figured out the problem - the latch requires a wider striker to activate the power switch. The tech then installed the correct striker for the new latch. The door closed and the dishwasher worked for 2 or 3 days.My wife was afraid to tell me it stopped working again. When she did, I set up another service call. The same tech came out with no parts on his truck. He tried to bend the striker so it would stay latched - no go, the door would not stay closed. He then removed the door sea and found that the door striker and latch open with almost no effort. He decided to order a new latch and striker assembly - a new door seal and new hinges. These should come next week and when I get them, I have to call for another service appointment, which I should get 1-2 weeks after my call.In the meantime, I am using a small metal L bracket and a C clamp so we can use the dishwasher. There is no doubt that this product is defective in design construction and materials. I have spoken to KitchenAid and they claim no problems with this machine. In the end, KitchenAid/Whirlpool will get what they deserve, fewer customers! Fortunately, I have had an extended warranty from Sears and just extended it for a year. The lemon law requires 4 repairs within the preceding 12 months, the fourth being within 60 days of the third repair. Should the next repair fail, I will use every resource available to get a new machine, obviously not a KitchenAid, including filing a claim in small claims court.

In October 2016, I bought stainless dishwasher model KDTEESS1. The appliance itself works well but after one year I noticed rust spots appearing on the front door. It has gotten worse. KitchenAid is not standing behind its product.The door was not sealed or finished properly. I contacted KitchenAid and was told the one year warranty had passed and I had to buy a new door. Clearly this door was defective as I have an older dishwasher which does not have this problem.

Our stainless steel, French door, KitchenAid refrigerator is a year old. The ice cube maker stopped working, so we had to have a service person come out. The diagnosis is that the ice maker broke, due to ice build-up. The part is under warranty, but the first service charge is $189.00 and they have to come again after the part is ordered. How can they charge to fix a part that is still under warranty that broke because it is defective? I will never buy from KitchenAid again.

I bought a KitchenAid refrigerator 6 years ago from Contra Costa Appliance in Walnut Creek, California. The refrigerator stopped cooling. Contra Costa Appliance repairman came promptly. The control board has failed. KitchenAid has discontinued making the part and it must be rebuilt, which will take 2-4 weeks. I must be without a refrigerator during that time. Discontinuing parts for a 6-year-old appliance is UNETHICAL!! SHAME ON KITCHENAID!

Our family has had problems with this microwave since we purchased in 2007. Realizing that recent history has proven manufacturers of some appliances cut overhead by skimping on parts made overseas, I assumed KitchenAid was a safe bet. I could not however have been more mistaken. I am what is considered a journeyman carpenter, mechanic, electrician and DIYer. So I assumed, again, mounting our new microwave should not have been space shuttle science. I was shocked and surprised to see how fragile the front intake grill design really was especially coming from a reputable company such as KitchenAid. If youre not extremely careful just mounting the intake grill where its supposed to attach could result in undue stress to the plastic tabs and cause them to break. The operative word being plastic unfortunately, not the real metal it is made to look or function as. Why were these at least not reinforced? About eight months later the main control board started giving us grief. Sometimes it would lock up or beep for no reason and other times would work fine. We lived with that for some time until the handle broke after a year and a half of normal use. By the looks of it, it seems the proximity of the heat from items being cooked caused it to crack mostly near the top where the handle is mounted, again causing stress fractures and ultimately causing the failure. I have been the sole provider for my family so money was something we cant be frivolous with. Weve ended up having to unplug the unit due to issues with the main control board. I am now in the market for another microwave and I will not buy another KitchenAid product. Unfortunately for my wife who has to match styles (since the range is also KitchenAid), this wont be an easy task. Ive always thought highly of this brand but I guess this new generation of people in manufacturing isnt what they used to be. Signed, DISSATISFIED CONSUMER.

We purchased a top-of-the-line Kitchenaid dishwasher 2 years ago. In the first year, we had 4 service calls for various problems. The last problem was for poor draining and residual soap in the bottom of the unit. Things were replaced and the door was taken apart, then reassembled. The problem persisted. I went online and did my own research and found the solution. Each repair person was sure to remind me to keep the rinse agent full. Turns out that when you have a water softener, the rinse agent is unnecessary. Now the entire door is showing rashes of rust.We called today and were questioned how the door was being cleaned. It is cleaned with a weak soap solution and immediately dried with a very soft microfiber cloth. Okay, so its not a maintenance issue. It is a very low grade of stainless steel. Magnets stick in the door readily, but not on the stainless handle, which is obviously a higher quality of stainless. After speaking to a manager, we are being sent a cleaning solution and a polishing solution. Sadly, had we researched before paying so much, we would have been informed that this is a chronic problem with Kitchenaid and they refuse to acknowledge the problem, nor will they offer any satisfactory solution. This dishwasher was bought to replace a 27-year-old Kenmore unit that just wasnt getting the dishes as clean as it used to. When it was taken to the junk yard, it looked like it did the day it was bought. The stainless parts were flawless. Dont make the same mistake we did. Take a magnet shopping with you and avoid Kitchenaid.

The dishwasher has been repaired two times and is leaking again. I hate this dishwasher and almost from day one. I only had it a short time and it started to leak all over my wood floors. We had it fixed and again. We had to pay to repair the leak a second time and again water on my wood floors. Today, I came upstairs to find water all over the floors again! Plus, it hasnt really cleaned the dishes well in a long time. I am going out today and shop for a new dishwasher and will not even consider KitchenAid. And I had a KitchenAid stove for a very short time and had to go out and buy a GE because at Thanksgiving, the oven stopped working. Right now, I have a KA refrigerator and cannot wait to get rid of it. I will never buy anything KitchenAid. Ill try Bosch or stick with GE!

Called about cracks on inside of door. Two horizontal cracks the largest about 10 long. They told me needed to have a service rep come out. Cost 99.99. I find out this is a common problem with KitchenAid refrigerators and is not covered by any warranty even an extended warranty would have expired in my case (6yrs). The repair is tape and screws or door replacement. This is obviously poor manufacturing that KitchenAid refuses to acknowledge. Shame on them.

As noted in many other reviews there is a design issue with the upper carriage. My wheels fell off New Years Eve and the upper basket fell down breaking 8 champagne glasses... several hundred dollars in broken glasses... dishwasher is 2 years old. Very unhappy.

I bought this free standing gas stove in 2010. It has been nothing but problems from the black enamel on top bubbling up to handles melting from the broiler and heating from hot to hotter - no in between. One word, JUNK. This is what should be on this stove. Made by Whirlpool Accubake junk!

Purchased from Lowe’s 9/21/18 and bought 5 year extended warranty through Lowe’s. Kitchen Aid did not supply refrigerator to Lowe’s until 11/15/18 (they said they weren’t ready to manufacture that model until then). I noticed first of August 2019 (8 months after delivery) that the long deli drawer (under the crispers) was not shutting completely on the left side. It stuck out like something stuck behind it. Upon checking, I found a block of ice (maybe 15” long by 5” high) behind the left half of that drawer. It was still under Manufacture warranty and they sent repairman from local appliance repair in 8/6/18.They returned 8/23/19 to repair. I had to empty the refrigerator and freezer 24 hours before and turn it off to allow the ice to melt I was informed. I did this. A pain is in the neck of course to relocate everything. The repair was made. 6 months later, I notice the same issue with left end of drawer not shutting. Sure enough, the same block of ice had returned. Called Lowe’s and they had no record of first incidence because that was MANUFACTURE WARRANTY incidence. Was rudely told this would be the FIRST incidence of such issue now that under Lowe’s extended warranty.I am set for yet another Appliance repair store to be here 2/13/20. So I’m sure they will also tell me to empty it before they return for repair! And my fear is this will be a temporary fix just like last time. I’ll be reporting it again in another 6-9 months and eventually my warranty will expire and I’ll be out the money because I have a LEMON!!! I think Kitchen Aid should replace it. I also would like to know if this issue has occurred often with this model. Maybe I don’t have a lemon, but the whole model manufactured at that time (between Sept 2018-November 2018) are faulty???

2006 Kitchenaid double sided door - model # kscs23inss: Freezer and fridge both sides are not cooling and after diagnostic found out motherboard - control panel is broken. They have a back order and unable to supply the part and offering only 15%. We as consumers invest our hard working money on major appliances from reputable companies like Whirlpool Canada and no after sale consumer protection to satisfy customer needs. The government needs to take action on these companies product defects in order to protect consumers.

KitchenAid Refrigerator KSSC48QMS01 - Do not buy this refrigerator. We bought a home with a beautiful custom kitchen with this KitchenAid refrigerator and its just given us grief. Thank goodness we bought an insurance package to cover appliance repair. After three different repairmen and waiting weeks for parts to arrive, we found out most parts were not the right ones. Finally we got a Sr. tech guy to assess what was going on and we had to have the mother board sent out to be re-done. Well that seemed to do the trick, but 8 months later we are having issues again. Our insurance carrier would NOT insure the refrigerator. We ended up buying insurance from another carrier which should have told us something. We have rented a refrigerator while new parts are being ordered. We have lost several full freezer and refrigerator loads of food. No fun. I have no confidence with this unit ever being repaired. Its built into its own lacquer custom cabinet. Ugh. We now have another rental refrigerator sitting outside on our patio as we wait two weeks for parts. Would I buy a KitchenAid unit again. No Way.....there is no help out there to fix this mess.

Side by side 2005 model - LIGHTLY used fridge, 2 adult household; suddenly stopped cooling! Seasoned repairman diagnosed main control board of computer failure which he said is COMMON so they have discontinued the model & carrying the part (MADE IN CHINA) only assembled here. Hopefully I will be getting part for ~$175 inc shipping from Sears (Whirlpool part). Do Not buy HIGH end products. They are overpriced & not any better. Found the same experience with Thermador microwaves - true planned obsolescence!

I purchased a model KDTE204DSS0 KitchenAid dishwasher on 12/1/14 for $717.48. It has a stainless steel tub. Fourteen months later (2/16) we had water leaking from multiple pinhole leaks in the stainless steel tub where the base of the tub is molded to fit the screen and pump. I called Whirlpool and they said that the tub has a lifetime warranty but it can only be installed by an approved appliance repair facility. That cost $150.00 (I removed, delivered and installed the dishwasher again myself). On 9/8/16 (seven months later) the dishwasher is leaking again and has again the same pinhole leaks in the new tub. I get a slight shock when I touch the screen inside the tub and believe there is a galvanic reaction going on that is eating up the stainless tub at its thinnest area.Since I find no other reviews mentioning this problem, and it appears to be more than just a tub problem but a unit problem (i.e. a lemon), I asked Whirlpool to replace the unit. As you already know, they said no but would replace it for $17.00 less than I paid for the last one less than two years ago. If I paid another $150.00 to replace the last tub that would be about $500.00 a year to wash a load of dishes every other day. This negative review is as much about the manufacturer as it is about the faulty dishwasher.

I have a KitchenAid Model KHHC2090SSS-2 Architect series. I have an extensive experience with concerns regarding this model. I replaced it once under warranty because it was arcing, and finally died completely. A year later, the microwave began to start on its own. There is nothing like walking into your kitchen and finding out the your microwave started it, set the cook time for an hour, and had already been running for 6 minutes. I called KitchenAid, and they immediately sent me to their safety department. They offered to fix it free of charge. Well, 4 months after being repaired, it started doing this again. After investigating this more, I have learned that KitchenAid has this problem, and Consumer Reports did an extensive investigation. Other models are involved. Fires have occurred. Buyer beware - these microwaves are a huge safety hazard.

We purchased our Kitchen Aid dishwasher for about $1000.00, when we renovated our kitchen. From day one, it was not a great appliance. It did not clean the dishes well, and it actually dried specs of food onto plates instead of washing them off. The little compartment that holds the soap started sticking closed within 6 months from purchase. After a couple of years, the door started squeaking very loudly when it was opened or closed, which was followed by the door balance strings snapping, breaking, and throwing the door to the dishwasher wide open. We had to get the balance kit replaced, which by the way currently looks different than the old kit, and actually does not do the same job. Its way tighter. Because the door flew open when the strings broke, it caused the hinges on the side to bend. Those had to be replaced as well. These parts were replaced by a kitchen aid service person. After the parts were replaced, our dishwasher would no longer lock. We were told by the service person that our model had a lot of issues an d the parts that are made now do not match up with the actual dishwasher. When I spoke with Kitchen Aid about this, they played dumb. They told me it was out of warranty and they no longer covered any repairs beyond this. My argument is that they are not even providing people with correct replacement parts to get the units to work correctly, so it seems like they are breaking the rules of warranty by not supplying customers with correct parts. Its very disappointing that they dont do a recall on an appliance that has so many known problems.

Looking for answers. About a month ago, one of the doors on my stainless french door fridge developed a hole from nowhere. Since then, the hole has gotten bigger and seems to be leaking metal. What on earth is going on???

We spent $665.11 on a microwave that lasted 1 year and 2 months. As is does not fall into their 1 year warranty, they refuse to help or compensate in any way. We had the same issue with a $900 dishwasher we purchased from KitchenAid a couple of years ago. BOTH appliances stopped working after exactly 1 year! It would seem that they are in the business of manufacturing CHEAP China appliances that break shortly after their warranty so you must purchase another one.Customer service is no help at all. They just read from a script repeating the same sentence over and over again. Other companies like Black & Decker and GE have much better customer service and ability to help customers when their products do not work. Would shop from them instead! KitchenAid KCMS1655BSS 1.6 cu. ft. Countertop Microwave Oven with 1200 Cooking Watts, 9 Quick-Touch Cycles, Recessed Turntable.

I purchased a new refrigerator on 12-13-12. It was a Kitchenaid French Door 29 model #KFIS29PBMS. Since purchasing this refrigerator I have had to place 9 service calls. Virtually, every part in the freezer/defrosting unit have been replaced and I am still having problems. Loud noises, PO light comes on continually. The repairman has thrown his arms in the air and said he doesnt know what else to do. He says it is a faulty design. I AM SOOO FRUSTRATED. PLEASE HELP!

I purchased an existing house with a KitchenAid Superba stove/cooktop and microwave combo. Everything worked fine for 6 months until I got the crazy idea to use the self-cleaning mode. The oven no longer heats now. I tested the heating elements and they are both fine. I found out that it is most likely the thermal shutdown fuse, a part that runs about $45-$50 online. I can do the replacement myself but as many others have said, I wont use the self-cleaning mode again. For those who cannot afford the cost for a service call, its a pretty easy part to replace - if in fact that is all that went bad during the self-clean. After reading the hundreds of the same complaints out there, I guess I feel lucky that my oven didnt literally explode and possibly hurt my 3 year old. I would be willing to join in a lawsuit, should a lawyer out there be interested.

In Nov. 2017 we installed KitchenAid double ovens, model KODE500EBS02. The ovens look very nice, but they are not for bakers. They take 10 to 15 minutes to preheat, they do not brown bake goods on the bottom, and they take longer to bake an item. The baked item is never done by the suggested time on a recipe. The ovens also bake hotter in the back. These were very expensive, so I am stuck with them, however, I would not recommend them to anyone else.

Why is it so difficult to make dependable products these days? We purchased a KitchenAid dishwasher in January 2013 and the control panel went out twice within the first year and now it is out again and the dishwasher will not run. The model number according to the inside of the machine is W10502126A. Now I just purchased a one year parts/labor warranty which was not cheap to have them come out to replace the panel. I bought the warranty because something tells me this is not a permanent fix rather a band aid as I think it will go out again before the year is up. Expensively made cheap product.

The dishwasher cleans the dishes reliably without worry! It was purchased in 1993 and it is still running great! It is a standard size dishwasher with a place separate for utensils. It is the top of the KitchenAid line at that time. It is the standard KitchenAid Superba from 1993. It has a black, shiny front with chrome control buttons. I have owned this dishwasher for a very long time. I have had one service call on it. I hope it lasts forever! The newer units are said to be less reliable and not as good at cleaning. I love this dishwasher. I am very pleased with it!

Superba YKEBC107KM - 2 issues; Door hinges seized and new thermostat blew after one self clean. 2 authorized repairmen failed to fix my door hinge problem. The 2nd guy said it would be $600 parts & labor in addition to the $150 service call that left my oven torn apart! I ordered new hinges and receivers from Partselect.ca and installed them myself. All good. I thought it would be smart to replace the 12 year old thermostat while I had the unit out. The replacement thermostat blew with the first self clean cycle. Partselect sent me a replacement which I just installed (now Im a pro at working on this unit!). I suspect the part is NOT at fault. Its more likely the lack of ventilation in the cabinet space to dissipate the extreme heat created during self clean. The thermostat is actually working properly. It senses the operating temperature has risen beyond what the components can handle and shuts it down. Unfortunately, this solution is not prioritized by manufacturers and technicians. The feature is what sells more units. So its true; more bells and whistles doesnt necessarily mean better! KA will not give consumers any insight into repair of their products. It is a racket that insulates the manufacturers through the technicians, financed by the consumer.

I have had my KitchenAid dishwasher for 3 years but have only had it working properly for 3 months. I had to replace the top basket parts TWICE, and the control panel is defective. I have 5 kids, work full time and have no time to beg and plead over warranties and complaint records. We have had nothing but problems, and KitchenAid Customer Service will not waive the service fee and parts cost to have it fixed. I have been calling and discussing this issue with them for over a year, and they wont help me resolve the issue. I was always under the impression that this company made durable products and stood by them, and it seems to be a BIG disappointment. It is now nothing but a fixture in our kitchen and hasnt been used since the summer of 2012. KitchenAid is NOT a company of customer service and product integrity. Buy at your own risk. I will not ever buy another product from them and refuse to give them any positive word of mouth. What a shame.

I purchased a KitchenAid dishwasher based on ratings. Wrong move. From day one, I should have returned it. Before installing it, the control panel had to be replaced. The print on the panel came off when the protective tape was removed. The tech service man came and replaced the complete panel. After about a week, there was a leak coming down the front of the door [stainless steel]. Repair man came again claiming it was due to steam from drying cycle. Took it apart now. Its okay. We have been complaining about dishes coming out dirty each time and have gotten different answers. Called a third time tech. Checked machine codes,claiming all was okay. But the hot water was not hot enough [120 degrees] at burner. Claims 87 degrees. We have never had a problem with past three machines, last one being a Maytag which was spotless but was not stainless steel and we were matching the new appliances. Another wrong move. Should have kept it. The last tech said he was sorry he had to tell me there was nothing he could do. However, if the tech would read the manual, it states that in the hi-temp cycle, the machine heats the water to up to 150 degrees. Maybe he could find another reason for dirty dishes. I am now going to Lowes to see if they can be of any help. This machine is a lemon. Also, dont lean over the counter top. The panel is so touchy that it will turn the machine on or off. The only pro is the machine is very very quiet . Maybe that is why the dishes are not cleaned, its not doing anything.

Ive had the KitchenAid microwave for less than 5 years now. For so many times that I would try to heat something, it comes up no hotter than it was when I put it in. This happens a lot. I just came back from a weeks vacation to find my microwave had been on fire. It turned itself on while I was away and caught on fire! The entire thing is melted inside. The silver circular thing on top is hanging down and the door even melted. My kitchen cabinets have been damaged. Thank God my house did not burn down!

After 2 years of light use (empty nesters) machine would not start. Service tech (not Whirlpool connected) said board was bad. To replace cost was almost $400 with a 30 day warranty. A 30 day warranty? Seriously? This dishwasher replaced another KitchenAid that never worked right & completely failed after 3 years. Now going to Bosch. KitchenAid will never be my choice again! Model KFDE104DSS2

This dishwasher (model KUDC10FXSS) was installed in early 2012. The electronic control panel went out less than a year later. It took about two weeks to get it replaced. Luckily it was under warranty. One year later it does not work again! I have been washing dishes by hand for more than a month waiting for this part to come in! I can never get a clear answer as to when exactly the repairman will get it. Clearly many other people are having this issue? The part seems to be in high demand! It is ridiculous. (We had another dishwasher for 20 years before this one - never had a problem!) I am so disappointed in KitchenAid not to mention frustrated! BEWARE before buying this dishwasher - or any by KitchenAid!

Bought a very expensive fridge and have had to get it worked on 2 times already. This time I am going to have to wait over a week to get someone out to look at it so I am out a fridge. If you cannot work on it then you should not be selling it. If you pay over $2600.00 for something you want it to work. When I called they said that yes they have been having trouble with that. Thank God I bought the extended warranty. I will never buy anything else from SEARS. And I will tell everyone I know not to. I am very surprised that this company can stay in business with the way they handle any issues that customers may have.

Some of the settings are confusing but this microwave is easy to clean. Its lightweight and space saving but a better color choices. The turntable mechanical can use a upgrade and for the price a square plate for cooking would be wonder considering the price.

I had a similar experience with the interior. I ordered from a major online retailer (delivery was quick and professional). However, while I ordered installation, the delivery team informed me they could not install a wall oven. So, I had to look around for someone to install, and then wait until they could come out. This took about a month. While I inspected the unit upon delivery, and all looked great, I made the mistake of keeping the oven racks in. After installation, I pulled out the cardboard strips that kept the racks from damaging the interior during shipping, to discover one was covering a quarter-sized chip. Brand new, never used oven. KitchenAid just said sorry, its beyond the 30 day warranty, and it is not covered by the 1 year warranty as they consider it cosmetic. I turned it on for the first time today, and it started smoking horribly (yes, I have removed everything from the interior, including the yellow plastic feet from the bottom rack). I also ordered the glass downdraft KECD807XBL01 cooktop (both items replaced 30 year old JennAirs) directly from Whirlpool and the blower does not even come on at all. But, at least that is within 30 days, so they are sending someone to repair it next week. Well see, but I doubt it will sway my view that I am done with KitchenAid.

We purchased the KitchenAid KEBS109 Single Oven, in-counter unit for our new kitchen five months ago. Why, I have no idea now. It was installed and worked up until this weekend where it now is a dead brick. All power was verified but nothing on the control panel. We called KitchenAid/Whirlpool for warranty service and they scheduled service for this afternoon between 1-5. No one showed. Note: I took the afternoon off to meet the technician. We called multiple times to find when they would be arriving and the same response was given to us each time - the tech will call 30 minutes before he arrives. We called tonight and spoke to a supervisor who tried to get us to take another day off. In all my life I have never had a company tell me, in their words, to stick it until today. But if I do find that (per the other complaints I have read) this repair will cost significant money I will have no choice but have this oven removed and I will personally drop it off at the front steps of the dealership with a note that they can..., but first take a sledge hammer to it.

Just cost me $1,602 in labor charges to fix a six-year-old KitchenAid, side-by-side built in refrigerator. Yep, the top of the line one! The parts were covered under the warranty because the appliance had a Freon leak, which caused damage to the compressor, evaporator coil,and heat exchanger. Now I ask you, if a company recognizes that their appliance should not break down in this way in only six years, as evidenced by their willingness to hand over the parts free of charge, shouldnt they pay for the labor as well?! Oh, and to get the parts for free, you can only use one of their authorized service people, who of course can and do charge whatever they want. This company should not even bother having a customer service dept. They do nothing except repeat their hard line and refer you back to the legalize of their warranty. Never would I buy a KitchenAid appliance again.

The control panel of my double wall ovens periodically puts out error codes and the only way to turn off the oven is by turning off the circuit breakers. Six months later, still no service. Multiple calls and run around by KitchenAid and the Extended Warranty company.

In 2012 I purchased my new home and upgraded to ALL KitchenAid appliances. It was costly and I wish I would have done better research on appliance manufacturers. Just before the warranty was up on the first year, my refrigerator was leaking water. KitchenAid came out and fixed the water dispenser tubing. The repairman suggested that I buy another warranty and to keep buying them. He added that KitchenAid appliances are constantly breaking and the refrigerator was the worst appliance for reliability. I purchased a new 1 year warranty and that was up 1 month ago. I did not renew the warranty this year due to recent unemployment. Now the thermostat is out and it is going to cost me $300.00. I am going to purchase the warranty on all of the other appliances and ride this out. BBB and Consumer Reports recommend Thermador. I will be certain to never buy KitchenAid again and will go with what is recommended by the experts. Thanks KitchenAid!

In a nutshell, the same part on my fridge (the thermistor assembly) has broken down 5 times since I bought it (roughly every three months) causing the fridge to simultaneously ice over yet not keep the food cold. I have a warranty on it, and per CAs Lemon Law, they should have replaced the fridge by now. But every time I call, they keep coming up with reasons why that it doesnt qualify for a Lemon replacement. (This latest time was that the latest repair had the same claim number because it was technically within 90 days of the last time a technician came out. By this logic, they could give me the same claim number till the end of time and never replace the fridge).I can afford a new fridge, but at this point its a matter of principle. I have wasted thousands of dollars in food, not to mention days of my life dealing with this issue -- and have become convinced (based on my research of other consumer complaints) that this is an issue KitchenAid is aware of and that they have knowingly foisted a faulty product & loophole-ridden warranty onto their consumers and EXPECT us to give up when they give us the run-around. I have researched lawsuits against KitchenAid and their warranty company and have been contacted by lawyers who are interested in pursuing a class action lawsuit. If you are interested in getting more information/participating in a class action lawsuit against KitchenAid, please email me.

Its not enough to say - I will never use another Kitchen Aid appliance, or - Ill tell all my friends to never buy this product!!!!!! If you have purchased a Kitchen Aid dishwasher with its cheap plastic material, that when heated by the heating elements become weak and crumble apart, you need to know that this is very wrong and against the laws and rights of anyone who purchased this product. That means that it is your duty to call the Whirlpool complaints department and let them know that they have broken the law!!! And that you wont stand for it. I have called and asked to speak with the highest level (supervisor). She asked me for my full name, phone # and address. I asked her a few questions: 1) Where are the dishwasher manufactured (not assembled)? She did not know. 2) What is the plastic made of (knowing that she would not know) asked then can answer these question for me, she did not know. 3) Why are there so many Model #s for the same dishwasher? She said only the manufacturer can answer that question (and she has no idea who that is). I told her that on the Consumer Affairs website, there are 548 complaints on the same or similar issues that I am having with my 1 & half yr old dishwasher. I explained to her that when the plastic gets hot, it weakens and parts start to break off. I was told that they have not had any complaints. I gave her the website and asked her what she was going to do about it. She said she would record the information then pass it on to her supervisor (who I had already spoken with and was told that there was nothing she could to for me). I said that I would like her to email me a copy of that report. She explained that that was not possible. I asked her for her name. She replied - Kathy. I asked her for her last name and she refused. I asked for a phone number where she could be reached and she refused and said it was against company policy. I replied by saying - Kathy, did you ask me for my last name, address and phone # when I called? (yes). I finished the conversation by saying - Kathy, you get to hide behind your comfy, corporate desk protected... while the rest of us get to buy your plastic crap and have no way of getting any compensation. Thank You Kathy!!! I am now in the process of taking Whirlpool to court. I have all the proof I need to prove that Whirlpool is negligent. Im not doing this to have my dishwasher repaired for free parts included (which the company Corbeil where I purchased the dishwasher has agreed to do). I am doing this because it is the right thing to do and I wish more people would do the same...

My Kitchen Aid double oven which is still under warranty was not heating up properly and when it did heat many, many items came out burned. I checked the temperature with an oven thermometer and the temperature was way off when the beep sounded that the desired temperature had been reached. It took about 20 minutes longer to reach the correct temperature (35-40 minutes in all).It is loud both pre-heating, cooking and cooling. I sent my complaints to Kitchen Aid. A repairman came out and told me the beep really doesnt indicate the temperature had been reached. Must heat another 20 minutes at least and put bread in the oven and see which pieces come out burned to identify the hot spots. Dont want hot spots? Use the convection feature and bake at a lower temperature. It rattles and whirrs and makes a deep throbbing noise. Apparently this is all normal!Called Kitchen Aid, said nothing had changed. Talked with a rep, then her supervisor. She kept with the party line and repeated what the repairman had said but added, If you open the door, heat will escape. I hope she didnt say this with a straight face!! To top it off, this is only 1 authorized repairman in our area. Guess who?? NOT OKAY!!!!!

I looked and looked at gas ranges - I was very excited to be able to use gas again. I selected this Kitchen Aid stove and was not told that the central oval burner, which I paid extra to have, would not provide more than a low flame. You buy the whole 5th unit for just pancakes only! The self-cleaning oven will not clean the sides of the oven, only the pan over the burner. The little top oven is meant only for warming, not baking or cooking because it cooks so unevenly that toast, food and cookies are done on the glass side and burned on the back side. I have had KA service people out twice and they say that thats the way it is and that it registers 350 degrees when checked. I could have bought an oven for less than 1/2 and had a better oven. Its not the company that produced my 30-yr-old KA mixer, is it?

Was 13 months old, basket was always temperamental, shakeup. When repair person came he knew the runners had to be replaced. Said Kitchen Aid has a kit to order and he has seen the problem before. Asked him why we were not contacted for a recall and he said they only recall for bigger issues like electrical issues. Called Kitchen Aid. They were more concerned with the date of purchase than the DEFECT!!! Told them I had an extended warranty and they said they didnt know why the repair person would say those things... Told me to put a claim for damages to broken dishes through whomever I bought the extended warranty... Should have been a RECALL KITCHEN AID!!!! They sent me a claim form for damages... Lets see what comes next!!!!

I have a 6-year-old Stoves dual fuel range cooker. Sure, its out of warranty, but now it only functions as a hob! The thermostat on the main oven failed last year. Stoves cant fix it because the company that made it has gone out of business (no thought of doing anything about it). Now the interior glass shielding on the secondary oven decided to shatter last night. I cant expect anything to last, but in these times, I expect that something would be fixable. I will never buy anything by Stoves again. It was an expensive item around $1500, so not exactly bottom of the range! But it definitely is bottom of all ranges!

We have had 5 service calls to try and fix the cooling in the refrigerator and the ice maker. This stainless steel side by side unit is barely a year old. Having this issue repaired has been such a headache. Whirlpool/KitchenAid has many hoops to jump through and documentation needed. A month later, this issue is still unresolved. I am about to purchase a new refrigerator and just consider this a loss. I will never purchase another KitchenAid appliance again.

My husband and I purchased a custom home in November of 2010. We wanted high end appliances in our new kitchen and have about $25K in KitchenAid products in our kitchen. The largest expense was our built-in refrigerator (model number KSSC42KVS). We paid $8,000.00 for this supposed high end refrigerator. 2 and a half years later, it sits completely dead in my kitchen. The past 3 months have been a nightmare. First, the ice maker assembly had to be replaced at a cost of about $400.00. The cheap plastic arm that closes the ice chute stopped working and allowed warm air to move into the freezer, then the compressor kicked in overtime trying to cool the compartment. 3 days after the ice maker was replaced, the refrigerator side stopped holding its temperature. The compressor would kick on, the freezer would drop to -10 and the fridge temp would go up to 56-60 degrees. The repairman was out again. This time he replaced the damper door assembly which allows the air to move from the freezer side into the the fridge side. Cost me $700.00. Again, everything was OK for about the 3 days and then the same problem happened again. The repairman was out again and this time replaced the thermistors. Again 3-4 days works properly, then compressor kicks on, freezer down to -10 and fridge up to 56. All this time my technician is conferring with Whirlpool technical support and following their recommendations. Now Whirlpool says the main circuit board is bad. It cannot be repaired because all of the inventory was wiped out by the tsunami in 2010. I will have to wait 2-3 weeks while my board is shipped out to a 3rd party vendor to be rebuilt. Now I am out another $600 as we had to buy a cheap fridge to put in our garage because my $8,000.00 is unusable. The board comes in, the repairman puts it in and within an hour after him leaving, the whole fridge just shuts off. The rebuilt board is bad. The repairman is back with a new board.. The fridge works fine for 3 days and then on June 27th, the same problem is back. I let it run for a couple of days and by the 29th, now the freezer isnt holding temp either. Both fridge and freezer are at 60 degrees. I called the repairman again and he tells me that Whirlpool is saying that they are out of ideas. My 2-year-old, $8,000.00 refrigerator has some electrical problem and it cannot be repaired. I will have to buy a new one. ARE YOU KIDDING ME? If I would have known what terrible quality KitchenAid is, I would have spent another $1,000.00 back in 2010 and bought a Sub Zero. Please do not be fooled into thinking that KitchenAid is high end and high quality!

We have now had 3 different refrigerators from Jenn-Air and KitchenAid in the last year because they keep breaking down. The Jenn-Air refrigerators compressor completely died and they had to give us a new fridge. We picked a KitchenAid and 2 months later it stopped making ice and we found out theres a wiring problem. They are giving us a new one again. I am so frustrated with this situation.

Bought our KitchenAid spring 2016. November 2016, I noticed our cupboards next to the dishwasher are ruined because someone at KitchenAid had a brilliant idea of doing a side steam vent instead of a front vent. Clearly the product designer at KitchenAid has never used their own product... or they just dont care about the consumers buying a poorly designed product.

Remodeled kitchen and purchased 4 kitchen aid appliances - thinking they were of great quality and would last. Had nothing but problems since purchased shortly after purchased. Had problem with microwave door problems with fridge - ice maker. Problem with oven when self-clean - shuts down and cant open door. Had fixed 2x -this is the 3rd time! Dishwasher fixed more than once - refused to get fixed again and pay over $300 - can buy a new one.I currently have an ice maker, dishwasher and oven that does not work. Raising 4 children, I am VERY dissatisfied with Orvilles where I purchased the appliances and ESPECIALLY KitchenAid - that doesnt back up the products they manufacture with defects. I will NEVER purchase anything KitchenAid EVER again or shop at Orvilles. I have paid so many service charges and part bills. I refuse to give them any more money!

We bought a new Kitchenaid refrigerator French door bottom freezer model # KFIS29BBWH03. The Fan noise is horrible. Sounds like an Ambulance coming down the road. Very unacceptable. We also have ice on the back of the unit inside the refrigerator part which the latest service man, whom we have had four come, said it was a problem with the indoor ice. It also causes the shelves to be wet all the time. The service man has ordered a new computer board for that issue but says the fan noise is normal even though we can hear it throughout the house. Just want to throw this refrigerator in the trash but it was very expensive and if they could fix the noise problem I would be happy. But the noise is driving me up the wall. Wont buy anything from Whirlpool, who owns Kitchenaid and Maytag, again.