Tipos de aparatos


Marcas de electrodomésticos


Categorías de artículos


Más artículos


Kenmore Accesorios
Kenmore Accesorios

Kenmore Appliance Códigos de error

Su desempeño confiable continúa siendo premiado por quienes mejor los conocen, los consumidores que han recibido a Kenmore en sus hogares durante más de 100 años.


Calentador de agua Códigos de error

CODE: LED flashes once every 4 seconds 
PROBLEM: Water heater is at idle (no call for heat, no fault condition) 
FIX: Normal operation 

CODE: LED alternates bright/dim 
PROBLEM: Water heater is heating (no fault condition) 
FIX: Normal operation 

CODE: LED flashes once every 3 seconds 
PROBLEM: Low flame signal 
FIX: Shut off the power and allow time for the burner box to cool. Properly position the flame rod. Clean the flame rod of oxidation (rust or residue) with fine steel wool or replace the flame rod. 

CODE: LED flashes 2 times every 3 seconds 
PROBLEM: Air pressure switch closed 
FIX: Check that blower operates and does not have any blockages in the venting. Turn off power to the water heater and check that all wiring is correct. Check for twisted, damaged or obstructed air pressure switch tubing. To check the switch, turn off the power to the water heater, disconnect the wires on the air pressure switch and check for electrical continuity. 

CODE: LED flashes 3 times every 3 seconds 
PROBLEM: Air pressure switch open 
FIX: Make sure there are no blockages in the blower or venting system. Check for proper venting according to the installation instructions. A long vent or blocked vent can prevent the pressure switch from closing when blower is running. NOTE: The blower high-limit switch is wired in series with the air pressure switch. Ensure blower high-limit switch is not open. 

CODE: LED flashes 4 times every 3 seconds 
PROBLEM: Exceeded temperature limit 
FIX: Gas control failure, replace the gas control valve assembly. 

CODE: LED flashes 5 times every 3 seconds 
PROBLEM: Flame out 
FIX: Check that the gas supply to the water heater is on. Ensure the water heater is properly grounded and operating at 115-120 volts. Check the flame rod position and make sure it's not oxidized, broken or disconnected. Ensure the igniter and flame rod ceramic insulator is not cracked or broken. If all conditions are good and will not light, replace the control. 

CODE: 6-1: LED flashes 6 times and then 1 time every 3 seconds 
PROBLEM: Ignition failure 
FIX: The gas control failed to ignite the burner and has gone into locked-out state. Make sure the gas supply is turned on. Make sure the water heater is properly grounded and is operating at 115-120 volts. Shut off the power and then check the igniter for broken or disconnected wires. Make sure the igniter and flame rod ceramic insulator is not cracked or broken.  

CODE: 6-2: LED flashes 6 times and then twice every 3 seconds 
PROBLEM: Pressure switch/high limit opened 
FIX: The gas control has sensed a repeated failure in the vent protection switches. Check for any blockages in the blower or venting. Check the air pressure switch tubing for kinks or leaks. See corrective actions for the symptom of the LED flashing 2 and 3 times. If all conditions and blower are good and the heater will not run, replace the control. 

CODE: 6-3: LED flashes 6 times and then 3 times every 3 seconds 
PROBLEM: Flame lost 
FIX: The gas control sensed a repeated failure in the flame sensing circuitry during operation and has shut down the water heater. Control failed to ignite the burner. Make sure gas supply is on. Check igniter for broken or disconnected wires. Make sure heater is properly grounded and operating at 115-120 volts. 

CODE: 6-4: LED flashes 6 times and then 4 times every 3 seconds 
PROBLEM: Flame out of sequence sensed 
FIX: The gas control sensed a malfunction in the sequence of operation and has shut down the water heater. Shut off the power and check that the wiring is correct and the heater is properly grounded. Restore power and reset the control. To reset the control, slide the ON/OFF switch to the OFF position. Wait for 10 seconds and move the switch back to the ON position. 

CODE: 7 LED flashes every 3 seconds 
PROBLEM: Flammable vapor sensor (FVS) 
FIX: The gas control has sensed a problem with the flammable vapor sensor. Replace the vapor sensor. If replacing the vapor sensor does not correct the fault, replace the control. 

CODE: 8-1: LED flashes 8 times and then once every 3 seconds 
PROBLEM: Flammable Vapor Sensor (FVS) 
FIX: The gas control has sensed a problem with the flammable vapor sensor. Replace the vapor sensor. If replacing the vapor sensor does not correct the fault, replace the control. 

CODE: 8-2: LED flashes 8 times and then twice every 3 seconds 
PROBLEM: Temperature sensor fault 
FIX: Control has sensed an error in the temperature sensing circuit and has shut down the water heater. If resetting the control does not clear the fault code, replace it., To reset the control, slide the ON/OFF switch to the OFF position. Wait for 10 seconds and move the switch back to the ON position. 

CODE: 8-3: LED flashes 8 times and then 3 times every 3 seconds 
PROBLEM: Gas control failure 
FIX: Control has sensed an error in the electronics of the valve and has shut down the water heater. If resetting the control does not clear the fault code, replace it. To reset the control, slide the ON/OFF switch to the OFF position. Wait for 10 seconds and move the switch back to the ON position. 

CODE: 8-4: LED flashes 8 times and then 4 times every 3 seconds 
PROBLEM: Gas control failure 
FIX: Control has sensed an error in the control circuits of the valve and has shut down the water heater. If resetting the control does not clear the fault code, replace it. To reset the control, slide the ON/OFF switch to the OFF position. Wait for 10 seconds and move the switch back to the ON position. 

CODE: LED is constantly on 
PROBLEM: Gas control failure 
FIX: Control has failed. If resetting the control does not clear the fault code, replace it. To reset the control, slide the ON/OFF switch to the OFF position. Wait for 10 seconds and move the switch back to the ON position.


Distancia Códigos de error

CODE: F001, F002, F004 or F005 
PROBLEM: Touch panel failure 
FIX: Disconnect electrical power from the range and wait 30 seconds then restore power. If the error code returns, disconnect electrical power and replace the touch panel. 

CODE: F003 
PROBLEM: User interface control board failure 
FIX: Disconnect electrical power from the range and replace the user interface board. The user interface control board may have more than one version. Use the latest revision of the user interface control board. 

CODE: F010 
PROBLEM: Runaway temperature (oven temperature is over 600 degrees and increasing) 
FIX: Disconnect power from the range. Check the resistance of the oven temperature sensor probe using a multimeter. You should measure about 1,100 ohms resistance through the sensor probe at room temperature. If not, replace the sensor probe. 

CODE: F011 
PROBLEM: Stuck key on the keypad 
FIX: The control detects a key has been pressed for 30 seconds or more. Make sure nothing is pushing against the keypad. Press the Stop key to clear the display. If the code won't clear, disconnect electrical power to the range and check the wire harness connections between the touch panel and the user interface control board. 

CODE: F012 
PROBLEM: Touch panel and user interface control board mismatch 
FIX: This code appears when you replace the touch panel or the user interface control board using the wrong part. Use your range model number to check the part number and install the correct replacement part. 

CODE: F013 
PROBLEM: User interface control board failure 
FIX: Disconnect electrical power, wait 30 seconds and restore power. If the error code returns, replace the user interface control board. 

CODE: F015 
PROBLEM: Touch panel failure 
FIX: Disconnect electrical power, wait 30 seconds and restore power. If error code returns, replace the touch panel. 

CODE: F017 
PROBLEM: User interface board is unable to configure the touch panel 
FIX: Disconnect electrical power, wait 30 seconds and restore power. If the error code returns, disconnect electrical power and check the wire harness connections between the touch panel and the user interface control board. Reconnect any loose wires or replace the wire harness if damaged. If you just replaced the user interface control board or the touch panel, you may have used the wrong part. 

CODE: F018 
PROBLEM: Relay control board failure 
FIX: Disconnect electrical power to the range and replace the relay control board. 

CODE: F019 
PROBLEM: User interface control board is unable to configure the relay control board 
FIX: Disconnect power to the unit, wait 30 seconds and restore power. If the error returns, disconnect electrical power and check the wire harness connections between the user interface control board and the relay control board. Reconnect any loose wires or replace the wire harness if damaged. If you just replaced the user interface control board or the relay control board, you may have used the wrong part.  

CODE: F022 
PROBLEM: Communication failure between the user interface board and the relay control board 
FIX: Disconnect power to the unit, wait 30 seconds and restore power. If the error returns, check the wire harness connections between the user interface board and the relay control board. Reconnect any loose wires or replace the wire harness if damaged. 

CODE: F023 
PROBLEM: Communication failure between the user interface board and the touch panel 
FIX: Disconnect power to the unit, wait 30 seconds and restore power. If the error returns, check the wire harness connections between the user interface board and the touch panel. Reconnect any loose wires or replace the wire harness if damaged. If the wiring harness is okay, replace the touch panel. If the problem continues, replace the user interface control board. 

CODE: F025 or F027 
PROBLEM: Communication between the user interface board and the relay board can't be initiated 
FIX: Disconnect power to the unit, wait 30 seconds and restore power. If the error returns, disconnect electrical power and check the wire harness connections between the user interface control board and the relay control board. Reconnect any loose wires or replace the wire harness if damaged. If you just replaced the user interface control board or the relay control board, you may have used the wrong part. 

CODE: F028 or F029 
PROBLEM: Communication between the user interface board and the touch panel can't be initiated 
FIX: Disconnect power to the unit, wait 30 seconds and restore power. If the error returns, disconnect electrical power and check the wire harness connections between the user interface control board and the touch. Reconnect any loose wires or replace the wire harness if damaged. If you just replaced the user interface control board or the touch panel, you may have used the wrong part. 

CODE: F030 or F031 
PROBLEM: Oven temperature sensor probe failure 
FIX: Disconnect power from the range. Check the resistance of the oven temperature sensor probe using a multimeter. You should measure about 1,100 ohms of resistance through the sensor probe at room temperature. If not, replace the sensor probe. 

CODE: F033 
PROBLEM: Meat probe temperature sensor shorted or too hot 
FIX: The control triggers this code if the meat probe detects temperature above 392 degrees F. Make sure you fully insert the meat probe into the meat. The meat probe will detect oven cavity temperature higher than 392 degrees if you don't fully insert the meat probe tip into the meat. Also, make sure that you insert the meat probe jack into the receptacle. A partially inserted meat probe jack can short the contacts in the receptacle, causing this error code. 

CODE: F050 
PROBLEM: Oven relay board can't detect the status of the door lock switches 
FIX: Disconnect power from the range. Check the wire harness connections between the door lock switches and the relay control board. Reconnect any loose wires or replace the wire harness if damaged. Check to see if the door lock switches work properly using a multimeter. Replace the door lock assembly if the switches don't work. Replace the relay control board if the wires and switches are all okay. 

CODE: F090 
PROBLEM: Door lock error 
FIX: The relay control board doesn't detect the door lock motor operating. Disconnect power to the unit, wait 30 seconds, then restore power. Try again to lock the oven door by initiating the Oven Lockout or starting a Clean Cycle. If the door lock motor doesn't run, disconnect power to the range and check the wire harness connections between the door lock assembly and the relay control board. 

CODE: F095 
PROBLEM: Door lock motor doesn't stop running 
FIX: If the door lock motor is constantly running, replace the relay control board because the relay on the circuit board is stuck. If the motor isn't running constantly when this code appears, replace the door lock assembly. 

CODE: F096 
PROBLEM: Oven door has been detected open during a self-clean cycle. 
FIX: Make sure the oven door closes fully and pushes the door switch plunger in. Adjust the oven door hinges or replace the door hinges if damaged. Disconnect electrical power to the range and test the door switch for continuity with the door switch plunger pressed in. Replace the door switch if you don't measure continuity during that test.


Lavadora Códigos de error

CODE: Lid Lock LED flashing 
PROBLEM: Indicates the control recorded one of the error codes shown below 
FIX: Enter the diagnostic test mode to read the error code as shown in the above video link. 

CODE: F0 E2 
PROBLEM: Excessive suds 
FIX: Use only HE (High Efficiency) detergent. Reduce the quantity of detergent to prevent excessive suds. 

CODE: F0 E4 
PROBLEM: High water temperature in the rinse cycle 
FIX: Make sure that fill hoses are properly connected. Check the resistance of the thermistor (temperature sensor). It should measure around 50K ohms (50,000 ohms) at 77 degrees. If the thermistor is defective, replace it. 

CODE: F0 E5 
PROBLEM: Unbalanced load 
FIX: Re-distribute the load inside the spin basket. If that doesn't help, then check the suspension rods and springs. If a suspension rod and spring is broken or damaged, replace all of the suspension rods and springs (the replacement part is a kit that has all 4 rods/springs). 

CODE: F1 E1 
PROBLEM: Main electronic control board failure 
FIX: Unplug the washer. Check the wiring connections on the main electronic control board in the console. If the wiring connections are okay, then the main electronic control board will usually need to be replaced. 

CODE: F1 E2 
PROBLEM: Motor control error on main electronic control board failure 
FIX: Unplug the washer. Check the wiring connections on the main electronic control board and the drive motor. If the wiring connections are okay, then the drive motor windings will need to be checked for resistance. If the drive motor is bad, replace it. If the drive motor is okay, the main electronic control board will usually need to be replaced. 

CODE: F2 E1 
PROBLEM: Stuck key 
FIX: This code is for models with a digital display. One or more keys on the user interface were actuated for 15 seconds or longer. If a key is stuck and cannot be freed up then the user interface control will need to be replaced. 

CODE: F2 E3 
PROBLEM: Mismatch of main electronic control board and user lnterface control 
FIX: This code is for models with a digital display. It typically occurs when an incompatible control component (Main Electronic Control board or User Interface control) is replaced in the console. Check the replacement part numbers and reorder the correct part. 

CODE: F3 E1 
PROBLEM: Water level pressure sensor fault 
FIX: Unplug the washer. Check the air hose connection between the bottom of the tub and the water level pressure switch on the main electronic control board in the console. If no problems are found, then the main electronic control board (which includes the water level pressure switch) will usually need to be replaced. 

CODE: F3 E2 
PROBLEM: Inlet water temperature fault 
FIX: Unplug the washer. Open the console and check the resistance through the thermistor circuit (black wires). It should measure around 50K ohms (50,000 ohms) at room temperature. If the thermistor is defective, replace it (the thermistor is a component in the inlet valve assembly wiring harness). 

CODE: F5 E1 
PROBLEM: Lid switch fault 
FIX: This code is displayed if Start is pressed with the lid open. If the lid switch on the lid lock/switch assembly isn't detecting the condition of the washer lid properly, then the lid lock/switch assembly will need to be replaced. 

CODE: F5 E2 
PROBLEM: Lid lock fault 
FIX: Unplug the washer. Check the lid lock/switch assembly for debris or an item that is interfering with the lock strike being engaged by the lid lock mechanism. If no interference is apparent, then the lid lock/switch assembly will usually need to be replaced. 

CODE: F5 E3 
PROBLEM: Lid unlock fault 
FIX: Unplug the washer. Lift the top panel of the washer to access the lid lock/switch assembly. Try to manually unlock the washer lid without breaking the lid lock/switch assembly and the lock strike. If the components are damaged, replace them. If the lid lock/switch assembly won't lock and unlock properly, replace it. 

CODE: F5 E4 
PROBLEM: Lid not opened between cycles 
FIX: If the washer is started several times without the lid ever being opened, then this code appears. If the lid is actually being opened between cycles but the control doesn't detect it, then the door lock/switch assembly will typically need to be replaced. 

CODE: F7 E1 
PROBLEM: Basket speed sensor fault 
FIX: See if the spin basket rotates freely. If not, then examine and replace any defective drive components. If the basket spins properly, unplug the washer and check the wiring connections on the shifter assembly. That component has the optical tachometer. If the wiring connections are okay, then that shifter will usually need to be replaced. 

CODE: F7 E5 
PROBLEM: Shifter assembly fault 
FIX: The main electronic control board cannot determine the position of the drive system shifter. Unplug the washer and check the wiring harness connections on the main electronic control board and the shifter assembly. If the wiring connections are okay, then the shifter assembly will usually need to be replaced. 

CODE: F7 E6 
PROBLEM: Motor fault 
FIX: Unplug the washer and check the wiring connections on the drive motor. If the wiring connections are okay, then the drive motor will typically need to be replaced. 

CODE: F7 E7 
PROBLEM: Motor is unable to reach target RPM 
FIX: Rotate the spin basket to see if it spins freely. If not, then a garment could be stuck between the outer tub and the spin basket. A problem with drive components could also cause excess friction. Inspect the drive components and replace parts as needed. 

CODE: F8 E1 
PROBLEM: Not filling or long fill time 
FIX: Water isn't being detected as entering the washer. If the washer isn't filling, check the water supply faucets behind the washer to make sure that they are fully open. Check the fill hoses and inlet water valves. If the inlet water valve assembly is defective, replace it. If water is entering the machine but not being detected, then the main electronic control board (which includes the water level pressure switch) will usually need to be replaced. 

CODE: F8 E3 
PROBLEM: Overflow condition 
FIX: If the washer is overfilling, check the inlet water valves. If the valves are not shutting off water flow, then replace the inlet water valve assembly. If the washer isn't actually overflowing, then the main electronic control board (which includes the water level pressure switch) will typically need to be replaced. 

CODE: F8 E5 
PROBLEM: Hot & cold fill hoses are reversed 
FIX: Check the fill hoses. If they are connected properly then the inlet water thermistor (temperature sensor) will probably need to be replaced. That component is part of the Inlet Water Valve Wire Harness. 

CODE: F9 E1 
PROBLEM: Long drain time 
FIX: The washer isn't draining after the drain pump runs for 10 minutes. Check the washer drain and the drain hose for clogs or restrictions. If the drain path is clear, unplug the washer and check the drain pump. If the drain pump is defective, replace it. 

CODE: Wash LED on 
PROBLEM: No fill or long fill 
FIX: Water isn't being detected as entering the washer. If the washer isn't filling, check the water supply faucets behind the washer to make sure that they are fully open. Check the fill hoses and inlet water valves. If the inlet water valve assembly is defective, replace it. If water is entering the machine but not being detected, then the main electronic control board (which includes the water level pressure switch) will usually need to be replaced. 

CODE: Spin LED on 
PROBLEM: Long drain time 
FIX: The washer did not drain after the drain pump has been running for 10 minutes. Check the washer drain and the drain hose for clogs or restrictions. If the drain path is clear, unplug the washer and check the drain pump. If the drain pump is defective, replace it.


Lavaplatos Códigos de error

CODE: 1-1 or F1E1 
PROBLEM: Stuck relay on the electronic control board 
FIX: Shut off power to the dishwasher for 5 minutes. If the code resumes when you restore power, check the wiring connected to the control board for damage and repair any broken wires. 

CODE: 1-2 or F1E2 
PROBLEM: Damaged or corrupted memory on control board. Incompatible software components inside microprocessor., 
FIX: Shut off power to the dishwasher for 5 minutes. If the code resumes when you restore power, replace the electronic control board. 

CODE: 2-1 or F2E1 
PROBLEM: Stuck button on the user interface control 
FIX: Check all buttons on the user interface control for a response. If one or more of the buttons don't work, unplug the dishwasher to disconnect electrical power and disconnect the user interface control wire harness. Reassemble the door with the user interface wire harness disconnected, but don't close the door. 

CODE: 2-2 or F2E2 
PROBLEM: User interface control can't communicate with electronic control board 
FIX: Shut off power to the dishwasher. Check the wiring between the user interface control and the electronic control board. If the wires and connections are okay, replace the user interface control board. If the problem persists, replace the electronic control board. 

CODE: 3-1 or F3E1 
PROBLEM: Thermistor/OWI sensor failure (The thermistor is the water temperature sensor, the OWI sensor is the Optical Water Indicator that detects the amount of debris in the water.) 
FIX: Unplug the dishwasher to disconnect electrical power and then check the wiring between the electronic control board and the thermistor/OWI sensor. Repair or replace the wire harness if broken. If you find the wiring undamaged, replace the thermistor/OWI sensor. 

CODE: 3-2 or F3E2 
PROBLEM: Shorted thermistor/OWI sensor 
FIX: Unplug the dishwasher to disconnect electrical power and then check the wiring between the electronic control board and the thermistor/OWI sensor. Repair or replace the wire harness if broken. If you find the wiring undamaged, replace the thermistor/OWI sensor. 

CODE: 3-3 or F3E3 
PROBLEM: OWI failed to calibrate or the drain hose check valve failed, allowing dirty water to backflow into the dishwasher 
FIX: Disconnect the dishwasher drain hose connection from the air gap or the garbage disposal if you have no air gap. Pour water through the drain hose to see if water backs up into the dishwasher tub. If so, replace the portion of the drain hose that connects to the drain pump because the check valve in that hose failed. 

CODE: 4-1 or F4E1 
PROBLEM: Communication error between the electronic control board and the circulation pump motor 
FIX: Unplug the dishwasher to disconnect electrical power. Check the circulation pump wire harness and reconnect any loose wires or replace the wire harness if damaged. If the wiring connections are okay, replace the circulation pump and motor assembly. If the problem continues, replace the electronic control board. 

CODE: 4-2 or F4E2 
PROBLEM: Communication error between the electronic control board and the circulation pump motor 
FIX: Unplug the dishwasher to disconnect electrical power. Check the circulation pump wire harness and reconnect any loose wires or replace the wire harness if damaged. If the wiring connections are okay, replace the circulation pump and motor assembly. If the problem continues, replace the electronic control board. 

CODE: 5-1 or F5E1 
PROBLEM: Door switch failure 
FIX: This code appears if you don't close the door within 4 seconds of pressing the Start/Resume button, or if the door latch assembly is broken. When starting a cycle, close the door within 4 seconds after pressing Start/Resume. If you can't start the cycle and the code continues, then the door switch could be defective. Unplug the dishwasher to disconnect electrical power. 

CODE: 5-2 or F5E2 
PROBLEM: Control detects door not opening 
FIX: The electronic control board expects to see the door open between cycles or the dishwasher won't start the next time you try to start a new cycle. If you didn't open the door between cycles, cancel the cycle. Open and shut the door, and then start a new cycle. If the cycle still won't start, then the door switch could be defective.  

CODE: 6-1 or F6E1 
PROBLEM: Won't fill 
FIX: Check for an item stuck under the overfill float and remove it. If the overfill float sticks in the "up" position the dishwasher won't fill. Unplug the dishwasher to disconnect electrical power and shut the water supply valve. Disconnect the water supply line from the water inlet valve and check the water inlet valve screen for clogs.  

CODE: 6-2 or F6E2 
PROBLEM: Water inlet valve failure 
FIX: Unplug the dishwasher to disconnect electrical power. Remove the bottom front access panel and toe panel. Check the wire harness connections on the water inlet valve. Reconnect any loose wires. Replace the wire harness if damaged. If the wire harness connections are okay, check the resistance of the water inlet valve using a multimeter. 

CODE: 6-3 or F6E3 
PROBLEM: Suds or air are in the water pump 
FIX: Check for sudsy water. If you see excessive suds, try to drain the dishwasher by cancelling the cycle. The drain pump will run for 3 minutes. If the drain pump can't drain the sudsy water, drain the water by hand or use a wet/dry shop vacuum to remove the water. Check the detergent dispenser and replace if it's damaged. Use only dishwasher detergent in the dishwasher. Using regular dish soap in the dishwasher causes excessive suds. 

CODE: 6-4 or F6E4 
PROBLEM: The float switch is open 
FIX: Check the overfill float switch to see if it's stuck or if an item is stuck under it. Check if the inlet water fill valve is properly shutting off the water supply when the dishwasher is off. 

CODE: 6-6 or F6E6 
PROBLEM: Incoming water is too cold 
FIX: Use an accurate thermometer to check the water temperature. If it's lower than 110 degrees F, check your water heater. If the water temperature is normal (110 to 120 degrees F), replace the thermistor/OWI or the electronic control board. Refer to the tech sheet for your dishwasher for a diagnostic test for the thermistor. 

CODE: 6-7 or F6E7 
PROBLEM: Disconnected or damaged flow meter 
FIX: Shut off power to the dishwasher. Check the wiring to the flow meter. If the wiring is intact, replace the flow meter. 

CODE: 6-8 or F6E8 
PROBLEM: Problem with water softener regeneration valve (Water Softener Models Only) 
FIX: Shut off power to the dishwasher. Check the wiring to the water softener regeneration valve. If the wiring is intact, replace the water softener regeneration valve. If the problem persists, replace the electronic control board. 

CODE: 7-1 or F7E1 
PROBLEM: Heating element doesn't work 
FIX: Shut off power to the dishwasher. Inspect the heating element and replace it if it's visibly damaged. If not, check the wiring to the heating element. If the wiring is intact, replace the heating element. 

CODE: 7-2 or F7E2 
PROBLEM: Heating element won't shut off 
FIX: Shut off power to the dishwasher for 5 minutes. If the code resumes when you restore power, replace the electronic control board. 

CODE: 8-1 or F8E1 
PROBLEM: Slow drain 
FIX: Shut off power to the dishwasher and then shut off water. Check the drain path for an obstruction. If the drain path is clear, check the wiring on the drain pump. If the wiring is intact, replace the drain pump. 

CODE: 8-2 or F8E2 
PROBLEM: Drain pump electrical problem 
FIX: Shut off power to the dishwasher and then shut off water. Check the wiring on the drain pump. If the wiring is intact, replace the drain pump. 

CODE: 9-1 or F9E1 
PROBLEM: Electronic control board can't detect the position of the diverter disc 
FIX: The diverter motor positions the disc that directs the water through the lower spray arm or the upper spray arm. The diverter motor also monitors the position of the diverter disc and sends position signals to the electronic control board. Unplug the dishwasher to disconnect power and check the wiring going to the diverter motor. 

CODE: 9-2 or F9E2 
PROBLEM: Diverter motor is stuck on 
FIX: The diverter relay on the electronic control board is defective. Unplug the dishwasher to disconnect electrical power and replace the electronic control board. 

CODE: 10-1 or FAE1 
PROBLEM: Detergent dispenser failure 
FIX: Unplug the dishwasher to disconnect electrical power. Remove the outer door panel and check the wiring connections between the electronic control board and the detergent dispenser. Reconnect any loose wires or replace the wire harness if damaged. If the wiring is intact, replace the detergent dispenser. 

CODE: 10-2 or FAE2 
PROBLEM: Vent wax motor electrical problem 
FIX: Shut off power to the dishwasher. Check the wiring in the vent wax motor circuit. If the wiring is intact, replace the vent wax motor. 

CODE: 10-3 or FAE3 
PROBLEM: Drying fan failure 
FIX: Unplug the dishwasher to disconnect electrical power. Check the wiring between the electronic control board and the drying fan. Reconnect any loose wires or replace the wire harness if damaged. If the wiring is intact, replace the drying fan.


Microonda Códigos de error

CODE: SE 
PROBLEM: shorted keypad. 
 
CODE: PF 
PROBLEM: Power Failure. 
 
CODE: E1, E2 
PROBLEM: Thermistor Failure. 
 
CODE: E11 
PROBLEM: Humidity Sensor. 
 
CODE: F1 
PROBLEM: Thermistor open - No heat or thermistor sensing error. 
 
CODE: F2 
PROBLEM: Thermistor short for cooking - No heat in 10 seconds after cooking starts. 
  
CODE: F3 
PROBLEM: Thermistor short after cooking - Thermistor temp does not go down after cooking ends. 
 
CODE: F4 
PROBLEM: sensor open - Humidity sensor sensing error. 
  
CODE: F5 
PROBLEM: Damper switch sensing error. 
  
CODE: F6 
PROBLEM: Microwave relay has failed. 
  
CODE: F9 
PROBLEM: an inverter failure. 
 


Refrigerador Códigos de error

ERROR: er 1F or er If 
PROBLEM: Main control board lost a feedback signal from the icing fan motor for over 114 seconds 
FIX: Fan – located in the rear of the freezer section and supplies cold air for the compartment where the ice maker is located 

ERROR: Er FF 
PROBLEM: Evaporator fan failed 
FIX: Fan motor, control board – wiring harness 

ERROR: Er FS 
PROBLEM: Freezer sensor error 
FIX: Sensor – wiring – connector problems 

ERROR: Er rS 
PROBLEM: Refrigerator sensor error 
FIX: Sensor – wiring – connectors 

ERROR: F dS 
PROBLEM: Freezer defrost sensor 
FIX: Sensor short – wiring problem 

ERROR: r dS 
PROBLEM: Refrigerator defrost sensor 
FIX: Sensor short – wiring problem 

ERROR: Er HS 
PROBLEM: Humidity sensor 
FIX: Sensor short – wiring problem 

ERROR: Er IS 
PROBLEM: Ice maker sensor 
FIX: Sensor short – wiring problem 

ERROR: Er SS 
PROBLEM: Pantry sensor 
FIX: The pantry is the deli drawer. Short in sensor or wiring problem. 

ERROR: Er rt 
PROBLEM: Room temperature sensor 
FIX: Short in sensor or wiring problem 

ERROR: Er It 
PROBLEM: System error inside ice maker 
FIX: Self-test ice maker routine 

ERROR: Er gF 
PROBLEM: Flow meter error code 
FIX: Water pressure – flow of water 

ERROR: F dH 
PROBLEM: Sensor did not get over 40F in defrost 
FIX: Faulty fuse – heater – control board 

ERROR: r dH 
PROBLEM: Sensor did not get over 40F 
FIX: Faulty fuse – heater – control board 

ERROR: Er 1F 
PROBLEM: The fan for the ice compartment failed 
FIX: Icing fan blocked – ice fan motor is defective – wiring in the circuit is defective – control board has failed 

ERROR: Er IF 
PROBLEM: ice compartment failed 
FIX: Icing fan blocked – ice fan motor is defective – wiring in the circuit is defective – control board has failed 

ERROR: Er CF 
PROBLEM: Condenser fan motor is defective 
FIX: Condenser fan motor – wiring – control board 

ERROR: Er CO 
PROBLEM: Communication error 
FIX: Communication error between main board and display board


Secadora Códigos de error

CODE: PF 
PROBLEM: Power failure 
FIX: A power failure occurred while the dryer was running. Press Start to continue the cycle or Stop to clear the display. If frequent power failures occur, check the outlet cord for the dryer. 

CODE: F:01 
PROBLEM: Main electronic control board failure 
FIX: Unplug the dryer for 5 minutes and then plug it in. If the code returns, then replace the main electronic control board. 

CODE: F:02 
PROBLEM: Keypad/user interface failure 
FIX: A button is stuck on the keypad on one of the two user interface control assemblies in the console. If you can't free the button, replace the user interface control assembly with the stuck button. 

CODE: F:20 
PROBLEM: Heater relay failure 
FIX: The heater relay on the main electronic control board failed. Unplug the dryer and replace the main electronic control board. 

CODE: F:22 
PROBLEM: Outlet thermistor failure 
FIX: The control detects an electrically open outlet thermistor (temperature sensor). Unplug the dryer and check the resistance of that thermistor, which should be about 10,000 ohms. If the outlet thermistor is defective, replace it. 

CODE: F:23 
PROBLEM: Outlet thermistor failure 
FIX: The control detects an electrically shorted outlet thermistor (temperature sensor). Unplug the dryer and check the resistance of that thermistor, which should be about 10,000 ohms. If the outlet thermistor is defective, replace it. 

CODE: F:24 
PROBLEM: Inlet thermistor failure 
FIX: The control detects an electrically open inlet thermistor (temperature sensor). Unplug the dryer and check the resistance of that thermistor, which should be about 50,000 ohms. If the inlet thermistor is defective, replace it. NOTE: The inlet thermistor is combined with the high-limit thermostat on this dryer. 

CODE: F:25 
PROBLEM: Inlet thermistor failure 
FIX: The control detects an electrically shorted inlet thermistor (temperature sensor). Unplug the dryer and check the resistance of that thermistor, which should be about 50,000 ohms. If the inlet thermistor is defective, replace it. NOTE: The inlet thermistor is combined with the high-limit thermostat on this dryer. 

CODE: F:28 
PROBLEM: Moisture sensor failure 
FIX: Unplug the dryer and check the wiring connections on the moisture sensor. If the wiring connections are sound, replace the the moisture sensor. 

CODE: F:29 
PROBLEM: Moisture sensor failure 
FIX: Unplug the dryer and check the wiring connections on the moisture sensor. If the wiring connections are sound, replace the the moisture sensor. 

CODE: F:30 
PROBLEM: Restricted airflow 
FIX: Clean lint from the lint screen. If you use fabric softener sheets, wash the lint screen with water and a soft-bristled brush to remove fabric softener buildup. Clear any clog or restriction from the exhaust air duct system to the outside of your home. 

CODE: F:31 
PROBLEM: Low L2 voltage 
FIX: The L2 leg of 240 volt power is below 30 volts. Check the house circuit breakers for the dryer and reset the L2 breaker if it's tripped. Unplug the dryer and check the power cord wire connections on the terminal block. Reconnect any loose wires or replace the power cord if it's damaged. Have an electrician check the 240 volt power supply for the dryer. 

CODE: F:70 or F:71 
PROBLEM: No communication between the electronic control board and the user interface control board assemblies 
FIX: Unplug the dryer. Check the wire harness connections between the main electronic control board and the user interface control board assemblies. If the connections are sound, contact a technician to diagnose the cause of the communication failure. The main electronic control board and/or the user interface control assemblies may might need to be replaced. 

CODE: F:72 through F:78 
PROBLEM: User interface control assembly failure 
FIX: Unplug the dryer. Check the wire harness connections between the user interface assemblies. Also check the wire harness connections between the main electronic control board and the user interface assemblies. If the wiring connections are okay, one or both user interface control assemblies probably needs to be replaced.



Kenmore Códigos de error del aparato

Kenmore códigos de avería del aparato

Kenmore códigos de diagnóstico del aparato

Kenmore símbolos de error del aparato

Kenmore fallos comunes del aparato


Reseñas de productos:

Model 59672389411 - I bought this ref for $1999.99. Sears wanted me to buy
Model 59672389411 - I bought this ref for $1999.99. Sears wanted me to buy a 799.99 5 year extended warranty. This was almost half the cost of the ref so I choose not to. I have never bought extended warranties before and have never needed to on appliances. I bought the ref on 7/10/15 and it stop working on 1/28/2017 that is 18 months later. Both the coolant lines were leaking. Repairman said he would have to replace them and the compressor. This is pretty much the complete sealed system. Cost would be $911.79. Again half the cost of the ref and I would only get 90 day warranty on that. I have called every number I can find for Sears. 1-888-507-9312 Sears corporate advocate who referred me to 1-888-536-6673 who referred me to 1-800-549-4505 Sears national customer hotline who told me there is nothing they can do. Before those calls I called 1-888-536-6673, 1-847-286-2500, 1-800-469-4663, and was given the e-mail address shc@customerservice.sears.com. No one at any of these numbers would help. I am just SOL. I have to throw this refrigerator in the land fill. I am appalled over this!!! Sears should be accountable for their products. I wanted to get in touch with the person who manufactured the ref because they should be accountable for the parts they make but no one will tell me who it is. I found a site that said Amana was the manufacturer. When I called them they would not say they made the parts. The consumer is being ripped off by Sears. As you can read in all the other reviews some thud is going on with the ref manufactured after 2015. I still do not have a ref and it is 3/12/2017. Because I am so mad I am going to report Sears to every agency I can find. Do not buy their products!!!
Publicado: March 12, 2017
Lisa of Washington, MO
Fuente: consumeraffairs.com

Sears replaced the bad fan. Theres a new part with a heater to prevent futu
Sears replaced the bad fan. Theres a new part with a heater to prevent future freeze ups.
Publicado: January 1, 1970
Robert of Centennial, CO
Fuente: consumeraffairs.com

I like my refrigerator from Kenmore. It has been a good thing for my family
I like my refrigerator from Kenmore. It has been a good thing for my family. I like the fact that it dispenses ice and water that are filtered and safe for me and my family. The refrigerator I owned in the past would always shut itself off, therefore spoiling all my food and causing a huge mess. With all the technology that lemme provides I dont have to worry about my money going to waste.
Publicado: November 8, 2015
Bradley of Owasso, OK
Fuente: consumeraffairs.com

My husband and I bought a Kenmore Elite refrigerator in October 2011. At th
My husband and I bought a Kenmore Elite refrigerator in October 2011. At the same time we also bought a stove, microwave, and dishwasher all Kenmore appliances. In December of that year our refrigerator started giving us an ER 1F error. We called and they sent a repairman out to look at it. They told us it was the ice maker blower motor. They replaced it and it was working fine. About 4 months later the same error occurred. They came back out and replaced the ice maker blower motor and the circuit board control that was suppose to fix the problem. It went out again and we tried to get them to replace the refrigerator but they wouldnt. Our warranty ran out in October of 2012. I had to pay $280.00 to have the same blower motor replaced about a month ago. Everyone of the repair men have told me that we are not the only ones with this problem. Why dont the company do something to fix it? The same motor has been replaced 4 times on my refrigerator. That should tell them that there is a problem.
Publicado: September 6, 2013
Agnes of Pontotoc, MS
Fuente: consumeraffairs.com

Para preparar el Día de Acción de Gracias, mi mujer puso en marcha el cic
Para preparar el Día de Acción de Gracias, mi mujer puso en marcha el ciclo de limpieza de nuestra cocina Kenmore. El cristal delantero se rompió. Llamó a Sears, (no pudo hablar con nadie que hablara inglés) el técnico dice que lo ha visto antes, pero que no es un defecto del fabricante y que tenemos que pagar. ¡Esto es una mierda! Por favor, que alguien nos ayude, estamos jubilados y no tenemos tanto dinero.
Publicado: November 21, 2014
quentin of Overland Park, KS
Fuente: consumeraffairs.com

Nunca tenemos que preocuparnos de que nuestra vajilla no esté limpia. EstÃ
Nunca tenemos que preocuparnos de que nuestra vajilla no esté limpia. Están perfectos después de cada lavado. El lavavajillas es tan silencioso que a veces tengo que comprobar si está encendido o no. El tamaño es perfecto para nuestra familia de 5 personas. Hay espacio perfecto para toda la cristalería en el estante superior, y mucho espacio para la vajilla en el estante inferior. Nuestro lavavajillas es blanco y combina con todos nuestros otros electrodomésticos. Combina con todo en nuestra cocina y zona de bar. La puerta tiene el asa perfecta para abrir el lavavajillas y los botones para el ciclo de lavado son muy fácilmente accesibles. Tiene una posición de bloqueo para que los niños no puedan jugar con él. El valor es todo lo que esperábamos. Estamos muy contentos con el rendimiento por el precio. Por favor, pruebe este lavavajillas, no le decepcionará. A prueba de niños o un niño también puede hacerlo funcionar.
Publicado: October 27, 2016
Lisa of Midland, TX
Fuente: consumeraffairs.com

Esta lavadora es horrible. La ropa no huele a limpio y sigue teniendo sucie
Esta lavadora es horrible. La ropa no huele a limpio y sigue teniendo suciedad sin importar el detergente que utilice. La secadora ensucia la ropa y la ropa de cama por el recogedor de pelusas que hace un trabajo horrible. No recomendaría el uso de la secadora a alta temperatura con todas las pelusas que pasan por la rejilla. Diseño horrible... es una pena que estas empresas no puedan hacer sus productos como antes. Más caros y menos fiables.
Publicado: July 12, 2017
Kimberly of New Oxford, PA
Fuente: consumeraffairs.com

La lavadora es increíble. Tiene diferentes ciclos de centrifugado dependie
La lavadora es increíble. Tiene diferentes ciclos de centrifugado dependiendo de tus preferencias. Es capaz de conseguir mi ropa agradable y limpia de manera oportuna. La apariencia es bastante común. Tiene los mandos en la parte superior y la lavadora se abre lo normal. La lavadora es muy fiable y no he tenido ni un solo problema con ella. Cuando necesito que me hagan la ropa con prisa, hace el trabajo muy rápido. Tiene una buena relación calidad-precio por diferentes componentes clave. Algunos son cómo funciona la lavadora, cuáles son las diferentes características y su aspecto.
Publicado: April 9, 2017
Mirah of Wilmington, DE
Fuente: consumeraffairs.com

Good quality, clean, efficient, hardworking product. Time tested and approv
Good quality, clean, efficient, hardworking product. Time tested and approved. Ive gotten many, many loads of laundry clean and fresh with this washer. This washer has been very reliable through many tough dirty jobs. Id recommend it for anyone looking for good, clean quality for great value and price. This washer is typical in looks but the value and quality more than makes up for aesthetics lacking, just buy it and see people... youll get clean value at a great price. You save time on presoaks plus its less expensive than others that seem to have the same value. It lives up to the value and more.
Publicado: August 7, 2016
Renee of Lewisburg, TN
Fuente: consumeraffairs.com

Siempre he utilizado electrodomésticos Kenmore y son fiables y el rendimie
Siempre he utilizado electrodomésticos Kenmore y son fiables y el rendimiento es un líder en su clase. Es resistente y duradero y me encanta este lavavajillas. El tamaño es el adecuado para mis necesidades. Se adapta perfectamente a la decoración de la cocina y estoy orgulloso de tener este lavavajillas en mi cocina. Pruébelo usted mismo y verá lo mucho que se enamorará de este lavavajillas. Muchos estilos diferentes que usted puede elegir para que no tenga miedo de que no es el adecuado para usted. Diferentes estilos y muchos colores diferentes para hacer de su cocina el lugar perfecto para estar. El valor habla por sí mismo debido al nombre involucrado en este aparato. Fuerte y fiable son sólo algunas de las muchas cosas que le encantará de este aparato.
Publicado: September 15, 2016
Michael of Hammond, LA
Fuente: consumeraffairs.com

My Kenmore washer lasted over 15 years with no problems. I still have the d
My Kenmore washer lasted over 15 years with no problems. I still have the dryer. I never has to call a repair man. The next washer I purchased lasted 8 years and I had to call the repair man several times. It was not a Kenmore.
Publicado: November 9, 2015
Susan of West Orange, NJ
Fuente: consumeraffairs.com

Cuando nos mudamos a nuestra nueva casa en la primavera de 2016, decidimos
Cuando nos mudamos a nuestra nueva casa en la primavera de 2016, decidimos quedarnos con el frigorífico Kenmore ya que tenía menos de 2 años. ¡Error! En los 18 meses transcurridos desde entonces, hemos sustituido las válvulas de la máquina de hielo 6 veces (1 válvula inferior, 3 válvulas superiores y 2 sustituciones de válvulas superiores que fallaron -de nuevo- mientras la reparación aún estaba en garantía). Este producto está fabricado por LG. Demasiadas molestias para un frigorífico de 2 años. Es seguro decir que cuando lo reemplacemos, no consideraremos las líneas de productos Kenmore o LG.
Publicado: December 30, 2017
Cande of Columbia, MO
Fuente: consumeraffairs.com

Kenmore estaba bien. Elegí esta marca y modelo inicialmente porque estaba
Kenmore estaba bien. Elegí esta marca y modelo inicialmente porque estaba en oferta a un gran precio y el ciclo HE que es bueno para ahorrar dinero y para el medio ambiente me convenció con su ventaja añadida. Me gustan las diferentes opciones de ciclo, incluyendo el ciclo HE. También es muy silencioso para ser un lavavajillas. Pueden ser bastante ruidosos, así que fue una agradable sorpresa para nosotros. Además, no era demasiado grande, pero parecía que cabían más platos en su interior de lo que cabría esperar. Sin embargo, tenía algunas ranuras extrañas donde no cabían los platos más grandes que parecía que debían caber. También no me gustaron un par de cosas como que no parecía limpiar los platos muy bien en cualquier ciclo y eso con nosotros pre-lavado y pre-remojo. En general, fue una decisión correcta debido a que no se gastó mucho dinero en absoluto. Si hubiera pagado el precio completo, habría estado muy decepcionado con esta unidad.
Publicado: May 14, 2017
Oliver of Portland, OR
Fuente: consumeraffairs.com

This performance of the washer was great. It was the size of an apartment w
This performance of the washer was great. It was the size of an apartment washer and I loved it and it got the clothes really clean and it was great. This model was very reliable and I would recommend this washer to anyone. It worked really well. People who live in an apartment would do very well with this model. The appearance of this model was just the right size for what I needed it for. People who want to buy, this is really a good buy and it will work for everyone. The value of this product is awesome and I think it had a very good value for me. I think that people will feel the same way if they want to buy this model.
Publicado: February 9, 2016
Cindy of Philadelphia, PA
Fuente: consumeraffairs.com

Last summer my electric company was promoting upgrading older but running r
Last summer my electric company was promoting upgrading older but running refrigerator with a new energy-efficient and paid $50 to customers who did so. My old refrigerator was already 20 year old but working just fine. I used the false logic that at 20 years old it makes sense to upgrade before old-dependable wore out. (Never needed service in 20 yrs!) Bought a new Kenmore 18 cu ft model from my local Sears store Aug 2016. Six months later it stops working. I find all the food inside is warm and frozen foods completely thawed. Sears repairman came out and quickly diagnosed the problem, states it is common for these units to leak out all the refrigerant. Asks if it is under 30 days old because Sears will just give me a new one but if over 30 days I must let them repair it. Compressor burnt out in less than 1 yr! I should have never gotten rid of my old refrigerator. Sears just lost another loyal customer; all of our appliance purchases has always been Kenmore.
Publicado: February 18, 2017
bob of Fraser, MI
Fuente: consumeraffairs.com

No es potente en la limpieza. Por lo general, dejaba restos de comida en lo
No es potente en la limpieza. Por lo general, dejaba restos de comida en los platos y en la vajilla de cristal. Sólo duró dos años antes de tener que cambiarlo. El tamaño del lavavajillas era bastante bueno. Tenía suficiente espacio en los estantes y la zona de los cubiertos era respetable para contener todos los artículos necesarios. Creo que un poco más de ajuste habría sido una orden para que usted podría conseguir más largo o debería decir artículos más altos en el lavavajillas. Los padres del lavavajillas encajan muy bien en mi cocina, hacen juego con el resto de mis electrodomésticos y me pareció que funciona adecuadamente con la decoración. Me pareció que el precio era un poco alto para la calidad. Después de usarlo durante un tiempo me imaginé que por el precio que estaba pagando y por lo que me dijo el vendedor que sería un buen lavavajillas pero desgraciadamente resultó no serlo por el precio.
Publicado: December 6, 2016
Peter of Silverdale, WA
Fuente: consumeraffairs.com

Mi lavadora ha funcionado bien durante más de 5 años. He lavado varias ca
Mi lavadora ha funcionado bien durante más de 5 años. He lavado varias cargas de ropa y siempre me ha dejado la ropa limpia. Trato de mantener cargas de tamaño medio. En la mía caben cuatro pares de vaqueros y varias camisas. Además, me gusta su simplicidad, no hay nada demasiado confuso. Tiene una perilla y controles simples. El blanco es el color tradicional. Estoy muy contento con mi lavadora. Definitivamente vale lo que pagué por ella. Hace el trabajo. Recomendaría este tipo de lavadora a cualquiera.
Publicado: April 11, 2017
Stacy of Cumberland, MD
Fuente: consumeraffairs.com

Pensé que estaba comprando un buen producto. He comprado Kenmore Elite en
Pensé que estaba comprando un buen producto. He comprado Kenmore Elite en el pasado. Pagué $2500 por el refrigerador en noviembre de 2016. Menos de 2 años después, la nevera está caliente. La misma historia que otros. Sears no puede venir durante 2 semanas. Otra empresa vino al día siguiente y confirmó que el freón se había ido. Aparentemente hay una fuga en una unidad sellada. El compresor estaba caliente y las bobinas no. No puedo quejarme a nadie porque el centro de llamadas está en el extranjero y no lo entienden. Llamé al servicio de atención al cliente y me dijeron que tendrían que transferirme. Esto sucedió 4 veces antes de que no pudiera soportarlo más y colgara. No se puede llegar a Kenmore Corporate. Toda la información de contacto está dirigida a Sears. ¿Hay alguna demanda colectiva a la que me pueda unir? Tengo una cita programada para que vengan en 2 semanas, pero tengo miedo de que me digan que será $1k o más para arreglarlo. Tiene menos de 2 años. No debería tener que arreglarlo. El técnico que vino me dijo que mi Kenmore está compuesta por piezas LG. Si quisiera un LG, habría comprado esa marca. ¿Por qué hacen eso? Ah, y mi lavavajillas Kenmore también se estropeó hace unos meses. Lo cambié por un Bosch. No volveré a gastar un céntimo en Sears o en un electrodoméstico Kenmore.
Publicado: August 7, 2018
Julie of Virginia Beach, VA
Fuente: consumeraffairs.com

The experience we had with our Kenmore Refrigerator was very positive. The
The experience we had with our Kenmore Refrigerator was very positive. The appliance was very durable as it lasted more than 15 years. That was the second longest tenure of any of our refrigerators since we moved into this home in 1967. It had to withstand opening and closing the appliance dozens of times on a daily basis as there was always great traffic around our Kenmore. Its like many of the Sears products that we have owned: tremendously sturdy and dependable. I would heartily endorse the Kenmore fridge.
Publicado: November 26, 2015
Peter of Wallingford, CT
Fuente: consumeraffairs.com

We need a new refrigerator and I am not sure yet if it will be a Kenmore. I
We need a new refrigerator and I am not sure yet if it will be a Kenmore. It did seem to stop functioning in some areas too soon. The ice maker stopped working and the refrigerator now leaks.
Publicado: December 23, 2015
Tammy of Covington, GA
Fuente: consumeraffairs.com

Compré la estufa más cara y de primera línea de más de 3k con el pensam
Compré la estufa más cara y de primera línea de más de 3k con el pensamiento de obtener el mejor producto que ofrecen. Si esto es lo mejor de Sears Kenmore lo siento mucho por cualquiera que haya pagado menos. Tiene dos ventiladores de convección pero cocina de forma desigual. Tarda 20 minutos en alcanzar la temperatura máxima si está a 400 y el servicio técnico de Sears le ha dicho que es normal. Mi vieja Jenn-Air de 20 años a la que sustituyó tardó 8 minutos en alcanzar los 450. El panel frontal parece un infierno después de 1 año. Mi perro puede pasar su nariz por él y encender los quemadores. Es un peligro para la seguridad ya que lo hizo cuando una toalla estaba en el quemador. El cristal superior si lo miras mal se raya. Yo uso ollas y sartenes de aluminio de fondo suizo nunca hizo una marca en el Jenn-Air y esta cosa se ve peor ahora después de 2 años que mi vidrio de 20 años hizo en la vieja estufa que tenía hierro fundido utilizado en él de vez en cuando. Esta es la mejor basura china que se ha hecho. Ya no se puede comprar un producto de calidad sin importar lo que se pague. Intenté cambiar el cristal y arreglar la estufa y no hubo suerte. Nunca volveré a comprar otro producto Sears, Kenmore y me esforzaré por decir a los demás lo pobre que es este producto. Si la estufa Jenn-Air no tuviera la parte superior destrozada cuando la puse en el cobertizo, estaría de vuelta en el lugar de este pedazo de chatarra y estaría afuera con un gran letrero diciendo lo terrible que son los productos y el servicio de Sears ahora. No es de extrañar que las herramientas Craftsman se hayan ido a Lowes y no es de extrañar que Sears esté ahora apenas por encima del agua. He terminado con ellos por completo. Debería haber aprendido la lección con el terrible lavavajillas Elite que tenemos y todos los problemas que tiene, pero intenté darles otra oportunidad, ya que hace 20 años sus productos duraban una eternidad en comparación con otras marcas.
Publicado: April 15, 2019
Joe of Jacksonville Beach, FL
Fuente: consumeraffairs.com

Buena máquina. Los platos siempre están limpios. Es inteligente con el ag
Buena máquina. Los platos siempre están limpios. Es inteligente con el agua. Tiene capacidad para más platos que la mayoría. Es muy silencioso. No necesita mucho jabón para lavar la vajilla, pero la deja limpia. Los estantes son lo suficientemente grandes como para sostener la mayoría de mis sartenes. Tiene dos estantes muy grandes. El único problema es que no hay lugar para los cubiertos. Es silencioso y hace el trabajo rápidamente. Los platos salen brillantes y todas las partículas de comida desaparecen. Muy bonito. Si se mantiene, el trabajo que se hizo para arreglarlo valió la pena. Fácil de mantener limpio por dentro y por fuera. Recomendaría este lavavajillas a cualquiera. Hace un gran trabajo manteniendo la vajilla y las ollas y sartenes limpias. Este lavavajillas me ahorra tiempo y energía. Recomendaría esta máquina a cualquiera.
Publicado: September 22, 2016
Barbara of Harrisburg, PA
Fuente: consumeraffairs.com

Compramos un flamante frigorífico Kenmore Elite de doble puerta francesa,
Compramos un flamante frigorífico Kenmore Elite de doble puerta francesa, de gama alta hace algo más de 3 años. Justo después de 3 años y la garantía se agotó, también lo hizo el compresor. También habíamos comprado un horno Kenmore, en el que el cristal se rompió justo antes de que se agotara la garantía. Realmente parece que Kenmore está en la obsolescencia planificada, y no hacer cosas para durar más. El reparador dice que las piezas y el arreglo no llegarán hasta dentro de 2 semanas. La experiencia ha sido mala teniendo en cuenta que hay que mantener las cosas en hielo, y la lentitud de la reparación. La experiencia ha sido mala teniendo en cuenta que hay que mantener las cosas en hielo y la lentitud de las reparaciones.
Publicado: May 8, 2019
Randall of Tucson, AZ
Fuente: consumeraffairs.com

It always seemed to work really well in keeping my clothes feeling and smel
It always seemed to work really well in keeping my clothes feeling and smelling clean. Never had issues with either washer or dryer. Only reason we dont have them anymore is because we finally decided to upgrade to a newer model. Very easy to keep clean as well. I never had an issue with it breaking down or having to fix any parts to it. Always seemed to get the job done when I needed it to and I do an average of at least 7 loads per week so I never once had a problem with either washer or dryer. It was very simple but thats what I most loved about them. Most of the newer washers and dryer have all these different buttons for certain washes and it can get confusing. For the price that I paid for both the washer and dryer I feel the value was amazing. Couldnt have really asked for a better combo for the price and it definitely was worth buying the set together.
Publicado: September 8, 2016
Jennifer of Glen Rose, TX
Fuente: consumeraffairs.com

Es genial. Lo recomendaría. Desde que lo tengo, ha funcionado muy bien y n
Es genial. Lo recomendaría. Desde que lo tengo, ha funcionado muy bien y no me ha fallado... ni una sola vez. No he tenido que arreglarlo ni nada y funciona tan bien como cuando lo compré. No tengo ninguna queja y es una buena relación calidad-precio. No centrifuga fuerte como muchas otras lavadoras y secadoras. Es como cualquier otra lavadora o secadora normal. No tiene un aspecto horrible y viene con una amplia gama de opciones como colores, etc. No es la marca más barata, pero obtienes lo que pagas. Prefiero pagar más y conseguir una máquina que sé que funciona muy bien y es fiable.
Publicado: April 11, 2017
Vicky of Plaquemine, LA
Fuente: consumeraffairs.com

We bought the Kenmore 600 series washing machine to go with our Kenmore dry
We bought the Kenmore 600 series washing machine to go with our Kenmore dryer less than 6 months ago. I have resorted to washing things twice with two rinses each and it still does not clean worth a damn. On top of that we are using clear HD detergent and yet our clothes are coming out with white spots on them. Never buy Kenmore again.
Publicado: September 11, 2016
Doug of Romeoville, IL
Fuente: consumeraffairs.com

I purchased a new Kenmore Elite Oasis washer and dryer and it has been the
I purchased a new Kenmore Elite Oasis washer and dryer and it has been the worst purchase of my life. The washer always displays LF and I have to re-position the clothes. The bleach stays full in the dispenser. The dryer is defective and always says the lint is full when it is NOT. My check did not bounce, but their product did! I want a refund!!! I will NEVER EVER purchase another Kenmore. They suck!
Publicado: June 25, 2014
Lisa of West Palm Beach, FL
Fuente: consumeraffairs.com

This refrigerator has been an excellent purchase. Lives up to expectations
This refrigerator has been an excellent purchase. Lives up to expectations of quality and value for the price. Would recommend to family and friends and would also purchase again. What more could you want?
Publicado: December 20, 2015
Frank of Amherst, VA
Fuente: consumeraffairs.com

Tonight, my Kenmore Elite 665 model control panel caught on fire. I was ups
Tonight, my Kenmore Elite 665 model control panel caught on fire. I was upstairs and my two daughters were yelling that something was burning. I came downstairs to find my kitchen full of smoke. The front of my dishwasher, the plastic has melted and there was soot on the stainless steel. We opened the control panel and everything was melted. I can not imagine what would have happened if I were not home. I have tried to call Kenmore but I was transferred 3 times. I want this thing replaced, I know it is not the first time this has happened. We are not the original owners, if it broke fine, but this could have burned our home down or injured someone in my family. Doesnt Sears or Kenmore care about that? I have seen numerous complaints about this same issue online. People have gone to the local news agencies just to get the word out. Do I need to take it that far? I need something done rather quickly to fix this situation. I have photos that I can pass on.
Publicado: September 24, 2011
Heather of Fletcher, NC
Fuente: consumeraffairs.com

It cools pretty good but is nothing fancy. Its just a plain jane, enough to
It cools pretty good but is nothing fancy. Its just a plain jane, enough to get by refrigerator. I wish it had an ice maker. I just cannot afford a higher quality, more high tech refrigerator. Its just your normal size. I really wish I had a bottom freezer, deluxe side by side model. It would have so much more room. It would have a bigger freezer to hold more. Says resist fingerprints but that is absolutely not true at all so I have mine covered in magnets and all my childrens artwork. A CHEAP REFRIGERATOR THAT FREEZES AND KEEPS STUFF COOL BUT NOTHING FANCY BUT I AM GLAD I HAVE IT. It could be worse and I couldnt have one at all.
Publicado: August 31, 2016
Teresa of Anderson, SC
Fuente: consumeraffairs.com

I really cant complain about the washers performance. It has always got our
I really cant complain about the washers performance. It has always got our clothes clean and never had any issues with it since the time of purchase. This washer is very reliable. My family has had and used it for many years and it still cleans our clothes as good as the time of purchase. No complaints on reliability. Im happy with the appearance. I have since learned of newer models that look a lot newer and sleeker, but at time of purchase it was exactly what we were looking for. I am very happy with the price. It was one of the only washers or dryer names that seemed to really make an effort to create a affordable and quality product.
Publicado: July 12, 2016
Shelby of Chicago, IL
Fuente: consumeraffairs.com

The dishwasher works well enough, it saves time from washing the dishes by
The dishwasher works well enough, it saves time from washing the dishes by hand but I do notice a lot of spotting on the dishes after theyve dried, which is kind of annoying. Good size. I can fit about a days worth of dishes into the dishwasher. Sometimes its a bit harder to do everything in one load though if there are a lot of pots and pans that day. Its a nice light color, which keeps the kitchen bright and cheerful and I enjoy that over darker colors. It has a nice shine to it but not too shiny to make a glare when the sunlight comes in.
Publicado: July 17, 2016
Lacey of Pueblo, CO
Fuente: consumeraffairs.com

Does a good job of washing the dishes and getting them dry. There is no soa
Does a good job of washing the dishes and getting them dry. There is no soap residue and they come out spotless. I am very happy with the job this machine does and would consider purchasing another in the future when needed. It is the perfect size for me and my husband. We are home alone most of the time. But even with company there is plenty of room for all the extra dishes. We are very happy with the size and how well it fits in our kitchen. Our dishwasher is a plain model. It is white in color and the buttons are on top of the door on the outside. It blends in very well with the rest of the appliances in the kitchen. We have had this model for several years now and are very happy with the value we have gotten out of it. With everyday that passes its value increases.
Publicado: July 29, 2016
Karen of Waterloo, IA
Fuente: consumeraffairs.com

It worked great and I had no problems with it. It did a very thorough job a
It worked great and I had no problems with it. It did a very thorough job and I would recommend it to others. The dishes came out sparkling. This dishwasher fit everything. There was room in it for a full load after meals. This was the best dishwasher I have ever had. The way everything fit inside was great. It was very appealing to me when I first saw it. The way it looked caught my eye immediately. It stands out from the rest. My friends compliment on it all the time. At first I thought it was just a typical dishwasher. The value of it has been seen. I no longer have to run dishes through it twice. Once is enough.
Publicado: June 16, 2016
Suzanne of Cheboygan, MI
Fuente: consumeraffairs.com

It performs really well. The dishes come out clean and shiny - they also sm
It performs really well. The dishes come out clean and shiny - they also smell good! I wasnt sure when I first bought the dishwasher whether or not it would perform well, but I have found that it is one of the best, if not the best, dishwasher I have ever had or used. My dishwasher is about 3 feet tall and 2 feet wide. It holds a lot of dishes, so I am very satisfied with it in that matter. It fits well in my kitchen, but it doesnt take up too much space, even though it is quite roomy on the inside. I love the color of it - it is black and silver, so it blends in with my other appliances (e.g. my refrigerator). It is quite shiny, too, but not too much of a shine. I would say that the value of the dishwasher is about $350, which is quite a bargain when it comes to dishwashers. This dishwasher is especially useful and high functioning, so it makes it even more of a bargain.
Publicado: March 26, 2016
Brandi of Crestline, CA
Fuente: consumeraffairs.com

Compré una lavadora Kenmore hace unos tres años, modelo serie 700 de alta
Compré una lavadora Kenmore hace unos tres años, modelo serie 700 de alta eficiencia hace un año tuve que cambiar la bomba. En el último mes comenzó a hacer ruidos fuertes cuando en el ciclo de centrifugado que comenzó a ser más fuerte. Hice una cita con un centro de reparación de confianza que he utilizado con éxito en el pasado y son muy conocedores. El mecánico que vino y lo miró dijo que los rodamientos están desgastados y que costaría 600 dólares reemplazarlos. Me puse en contacto con Kenmore y les pregunté si podían ofrecerme algún tipo de ayuda teniendo en cuenta que sólo tiene tres años y creo que debería haber durado más tiempo, ya que sólo somos dos personas en la casa. Me ofrecieron un vale de 75,00 para comprar una nueva. Estoy decepcionada y creo que, puesto que compré la máquina pensando que era un nombre conocido, me ofrecerían algo más de lo que es un precio de venta dominical. Recientemente he comprado otra máquina y siento decir que no compraría otro producto Kenmore.
Publicado: May 6, 2017
George of Monroe, CT
Fuente: consumeraffairs.com

Esta ha sido la lavadora más fiable que he tenido en bastante tiempo. Es d
Esta ha sido la lavadora más fiable que he tenido en bastante tiempo. Es demasiado triste que los electrodomésticos Kenmore no sean muy populares desde que Sears ha dejado el mundo de la venta al por menor. Siempre fui un cliente de Sears, Kenmore para todas mis compras de electrodomésticos importantes.
Publicado: May 17, 2020
Joseph of Nazareth, PA
Fuente: consumeraffairs.com

It worked well for the price. It lasted a few years before I had to replace
It worked well for the price. It lasted a few years before I had to replace it. Overall I did enjoy it for the quality cleaning it provided for me and my clothes. It lasted a long time and managed to keep my clothes dry and clean without taking a long time. It was a quality piece of machinery that makes me want to go and get another. The look is very professional and clean, without being too distracting. I enjoy its quiet presence, not needing to be flashy to be appealing to consumers. I would buy another soon. The washer and dryer are worth the price for the amount of time they last. I feel that it is important to find a good deal, and these two are just that for anyone on a budget.
Publicado: March 21, 2016
Thad of Plymouth, MI
Fuente: consumeraffairs.com

We have had the refrigerator for 8 1/2 years. No problems, so we are happy
We have had the refrigerator for 8 1/2 years. No problems, so we are happy with it. We have referred Kenmore refrigerator to our friends and our daughter too. The freezer works well too. I like to cook and bake enough so I can freeze leftovers. This saves lots of money. My husband loves chili so I put the extras in small plastic bowls so if he wants chili he can go to the freezer and have his chili.
Publicado: December 10, 2015
Christine of Cypress, TX
Fuente: consumeraffairs.com

My Kenmore dryers performance is efficient and gets the job done quickly an
My Kenmore dryers performance is efficient and gets the job done quickly and quietly. Its also easy to use and takes the guesswork out of trying to figure out drying times. My Kenmore dryer has plenty of room for all my needs. Its especially useful for washing larger loads of pet linens and bedding, and handles delicate clothing as well. My Kenmore dryers appearance is good. The front load feature is convenient especially when drying blankets as being able to see items helps to know if things are bunching up. My Kenmore dryer is a good value because it is energy efficient and allows me to dry more items together which in turn means being able to do fewer loads.
Publicado: June 12, 2016
D of Tualatin, OR
Fuente: consumeraffairs.com

I have no trouble out of it and it works like new and I have had it over 5
I have no trouble out of it and it works like new and I have had it over 5 years now and I will recommend to anyone. I am very happy with it and I would get another one. I dont know the size but its side by side and has a built in ice maker and fruit saver and lunch meat storage and its big. Its white and has two storage container and it takes up most of my kitchen space but I have a lot of storage and it holds a lot of food. It cost a lot but it was worth it. I pay a lot but I know it will last and I wont have to buy another one for a long time to come and I like it and I had a choice of plenty.
Publicado: June 1, 2016
Juanita of Asheville, NC
Fuente: consumeraffairs.com

He estado leyendo las malas críticas sobre estas lavadoras ya que tengo un
He estado leyendo las malas críticas sobre estas lavadoras ya que tengo una con el mismo problema común de no limpiar la ropa y dejar pelusas o detergente pegado. En teoría, la lavadora determina la cantidad de agua que necesita y el usuario no tiene control sobre ella. En mi última carga abrí la lavadora periódicamente y comprobé. La ropa estaba mojada pero no sumergida en absoluto. Palpé y sólo había unos cinco centímetros de agua debajo de la ropa. Con el tiempo, tomé algunas fotografías. Parecía que no había cambiado casi nada. El mismo cortavientos y la misma sábana de franela estaban visibles en la misma relación entre sí todo el tiempo antes del primer centrifugado.He tenido cargas que han salido con manchas de sequedad en algunas de las coladas. Creo que el problema de fondo es que no hay suficiente agua, así que tal vez sea un problema del sensor. He hablado con un técnico y dice que es la naturaleza de este diseño. Simplemente no está hecho para hacer flotar la ropa y removerla lo suficiente para que quede limpia. Me preguntaba si alguien ha conseguido resolver este problema.
Publicado: November 20, 2018
David of Somers, CT
Fuente: consumeraffairs.com

Its a good washer and has last many years. It has never broke down and neve
Its a good washer and has last many years. It has never broke down and never given me any problems. It does a good job cleaning so I like it very much. It has fit all of my problem since I have had this washer. It is strong and really does a good job cleaning my and my familys clothes so it has been good to me and has done its job good. The look of this washer is very nice. It sets up well and does not move. I like the way it looks and it fits all of the things around the house. It cost a little more than I thought it would but it has paid for itself many time over so I really can not complain about the price of this washer.
Publicado: March 28, 2016
Danny of Warrensburg, MO
Fuente: consumeraffairs.com

Mi frigorífico tiene cuatro años y no ha dado problemas. Lo compré en lÃ
Mi frigorífico tiene cuatro años y no ha dado problemas. Lo compré en línea en Sears, y me lo entregaron y lo instalaron sin problemas. Es silencioso y no podría estar más contento con su rendimiento y apariencia.
Publicado: August 30, 2019
Michael of Foley, AL
Fuente: consumeraffairs.com

No compre ningún frigorífico Kenmore. No respaldan sus productos. Tengo u
No compre ningún frigorífico Kenmore. No respaldan sus productos. Tengo un frigorífico de hace dos años (Kenmore Elite) que tiene manchas de óxido por todas las puertas exteriores, lo que debería ser un defecto del material, pero se niegan a hacer nada al respecto.
Publicado: January 31, 2018
Lisa of Millbury, MA
Fuente: consumeraffairs.com

Compré una cocina de cristal Kenmore hace diez años. Tenía todo lo que q
Compré una cocina de cristal Kenmore hace diez años. Tenía todo lo que quería, desde la función de autolimpieza, el cajón para calentar, el quemador superior para calentar, por nombrar algunos. Sin embargo, el primer problema que tuve fue que los tornillos de las manijas de las puertas necesitaban ser apretados constantemente, y luego el área alrededor del frente de la manija se agrietó. El otro día, mientras esperaba que el horno se precalentara, hubo una explosión, la puerta se abrió y el interior del horno se incendió. Conseguimos controlarlo sin tener que llamar al 911. Y pudimos apagar el horno en la parte superior de la estufa (leyendo otros comentarios, la gente tuvo que apagarlo en el disyuntor). Mi casa estaba llena de humo. No hace falta decir que estoy en estado de shock y horror por esta situación. No puedo entender por qué ha sucedido esto. ¿Y si hubiera utilizado el modo de autolimpieza? El horno habría estado bloqueado. Supongo que habría volado la puerta... No consideraré la posibilidad de reparar el horno, ni consideraré otro electrodoméstico Kenmore de ningún tipo. También compré un lavavajillas Kenmore que nunca lavó bien los platos desde el principio y las piezas eran baratas. Lo reemplazamos en 5 años. Me molesta gastar el dinero que tanto me costó ganar en una basura que no funciona bien cuando la tienes y hay que cambiarla cada 5 años. Tengo un frigorífico de 30 años en mi sótano y nunca he tenido un problema con él, que es lo que solía ser. Usted reemplazó esos artículos porque quería actualizar el estilo y la tecnología - no porque se incendió y potencialmente podría haber quemado la casa. Lo que es más preocupante es que hay un montón de las mismas quejas aquí sobre los incendios y no se ha hecho nada al respecto.
Publicado: June 7, 2015
A of Coatesville, PA
Fuente: consumeraffairs.com

My dryer has been very good. It dries a lot of clothes in a small amount of
My dryer has been very good. It dries a lot of clothes in a small amount of time. The clothes come out very warm and dry! The dryer is so reliable! I have had it for a couple of years and nothing has happened to it! It is strong and sturdy! It has never failed me and always dries the clothes. The appearance is nice. It is a very classic white dryer. Its very nice and the buttons are easy to use. It is very self-explanatory and very nice and clean. The value for this dryer is excellent because it has never broken down and still dries like the first time. The price is good and it does its job. I recommend it to everyone!
Publicado: August 10, 2016
Bryant of Whittier, CA
Fuente: consumeraffairs.com

These units are a separate matched pair, Kenmore Elite ref and freezer. I p
These units are a separate matched pair, Kenmore Elite ref and freezer. I purchased these units in Jan. 2011 but didnt plug them until Sept. 2011 because I remodeled the kitchen. Neither unit worked properly. From the start, the freezer would not get below 22 deg. The repairs finally got the freezer working. The ref has never gotten below 39 deg. with temp control on 7. The compressor has been replaced, thermostat, the timer and then rechecked at another appointment but it still will not cool. On 24 Nov., it was 48 deg, on the 25th, 42 deg. Today it is 40. deg. I have had at least 7 or 8 appointments for these units. On Nov. 24, 2012, I had to purchase another Kenmore ref as a back up because I cannot depend on this unit, which I could not afford because I am on a fixed income (disabled). I talked to lemon service, 1 800 927 7836, today. Their service records are not accurate. One comment from the Tech repairman stated I didnt want any more service. This is not correct. He said he didnt know what else to do. I need to be contacted about more info. Please.
Publicado: November 26, 2012
James of Auburn, WV
Fuente: consumeraffairs.com

Mi estufa eléctrica Kenmore, horno es 20 años de edad. Eso es cuando Sear
Mi estufa eléctrica Kenmore, horno es 20 años de edad. Eso es cuando Sears los vendió. Hoy no compraría otra. Kenmore fue comprado por otra empresa y ahora son basura.
Publicado: February 11, 2021
Jeanne of De Pere, Wisconsin
Fuente: consumeraffairs.com

Durable, reliable, efficient, love to use these. My washer washes really we
Durable, reliable, efficient, love to use these. My washer washes really well and my dryer is phenomenal. I have had them for 3 years and are still going strong. I would recommend Kenmore to everyone. I am pleased so much by this brand.
Publicado: November 22, 2015
Regina of Houston, TX
Fuente: consumeraffairs.com

Me gusta la lavadora. La única queja es que no permite ajustar el nivel de
Me gusta la lavadora. La única queja es que no permite ajustar el nivel de agua, aparte de eso hace el trabajo. Comprada en sears en una de sus rebajas. La cesta es enorme y se pueden lavar mantas y alfombras voluminosas.
Publicado: May 18, 2020
Donna of Citrus Heights, CA
Fuente: consumeraffairs.com

I can no longer use the rinse aid feature. Does a poor job cleaning. It has
I can no longer use the rinse aid feature. Does a poor job cleaning. It has great features, but they dont work anymore. Stopped working in less than a year. Totally adequate. Looks fine. Just doesnt work all that well. It was great when it worked. Made a big difference in the way dishes looked and its been very disappointing ever since.
Publicado: March 9, 2016
R of Springfield, MO
Fuente: consumeraffairs.com

The refrigerator I purchased was always temperature controlled correctly an
The refrigerator I purchased was always temperature controlled correctly and never had any issues. Easy to clean. The color perfectly complimented my house. The refrigerator I purchased had plenty of space. There were plenty of shelving spaces and temperature controlled drawers. The freezer was also roomy and fit my needs for a family of 6. The refrigerator I purchased perfectly matched my kitchen decor and additional appliances. It was the perfect size and fit in the corner of my kitchen perfectly. The refrigerator I purchased was very affordable, especially for a brand considered to be high quality. It also had high resale value when I moved and had to sell it. It was the most difficult of the appliances I had to sell to let go.
Publicado: March 10, 2016
Kim of Corbin, KY
Fuente: consumeraffairs.com

El calentador de agua Kenmore lo instalé hace 2 años y medio. Hace un añ
El calentador de agua Kenmore lo instalé hace 2 años y medio. Hace un año el piloto empezó a apagarse solo cada pocas semanas. Lo encendía y obtenía el agua caliente. Finalmente el piloto se apagó y encenderlo no funciona. No hay agua caliente pero el piloto se enciende con cuatro parpadeos seguidos de una pausa. El fabricante me dijo que esto indica que la válvula de control de gas y el termostato han fallado y que es necesario cambiarlos. El fabricante no tiene nada que ver con la sustitución de la pieza, así que me remitió al departamento de piezas de Sears. El Departamento de Piezas aceptó enviar una pieza sólo después de que su técnico (el mío no lo hará) venga a mi casa y diagnostique el problema, pida la pieza y haga la reparación. La visita del técnico a mi casa costó 79 dólares, sin incluir las piezas ni el trabajo de reparación. Su diagnóstico fue completamente diferente al de los fabricantes. Su diagnóstico y sugerencia de enjuagar el tanque y restablecer el indicador de la luz piloto no garantiza el repentino apagado del piloto. Por eso me recomendó que comprara un año o dos hasta cinco años de garantía, entre 50 y 200 dólares. Esto en la parte superior del costo de su diagnóstico controvertido que costaría $ 188. He pagado 500 dólares por esta Kenmore hace menos de tres años. Cuando insistí en la necesidad de cambiar la válvula de control de gas, el termostato accedió a escribir un segundo diagnóstico. Esta vez el costo sería de 214 dólares garantizados por 90 días solamente. Nuevamente sugirió comprar una garantía de servicio. Dije no gracias y no esperen que les pague por esta visita ya que el problema está mal diagnosticado.Hablé con el departamento de servicio al cliente unas cinco o seis veces. Me aseguraron que puedo obtener la pieza en garantía de forma gratuita después de que el técnico de Sears diagnostique el problema y pida la pieza necesaria para mí, entonces puedo hacer que mi propio técnico haga la reparación. El Departamento de Recambios insistió en que no existe tal cosa. El calentador de agua tiene una garantía de 9 años para las piezas, pero sólo un año para la mano de obra. Menos mal que tengo un segundo calentador de 40 años que sigue funcionando perfectamente. Esto me da tiempo para solucionar el problema de Kenmore. Estoy comprando otro calentador de agua pero definitivamente NO UN KENMORE. Tampoco volveré a comprar nada de Sears. Tratar con Sears en este asunto resultó ser una pesadilla. Estoy considerando la posibilidad de recurrir a un tribunal de reclamaciones.
Publicado: April 30, 2014
Samira of Carmichael, CA
Fuente: consumeraffairs.com

The Kenmore Elite bottom freezer refrigerator we purchased less than 3 mont
The Kenmore Elite bottom freezer refrigerator we purchased less than 3 months ago has been a problem and has ruined our kitchen floor under the appliance, and the adjoining rooms carpet . The ice maker line backs up and fills up in the back of the appliance and then leaks onto your floor. We have had 4 appointments scheduled for the repair (on a 3 month old product), and now we are waiting to see if we can have it replaced. It was repaired once to no avail. Now we are just waiting without ice, and our refrigerator is in the middle of our kitchen so the floor can dry out...again. Waiting for the company to contact us about a new or a replacement. I am very discouraged at this point. VERY!
Publicado: April 27, 2016
lyn of Denton, MD
Fuente: consumeraffairs.com

It was my first time buying one. I was pleased. It was easy to clean. It wa
It was my first time buying one. I was pleased. It was easy to clean. It was enough space and it made my kitchen look even better. I would buy it again but Im still enjoying my first one. Its nice to have. Its huge enough room for everyones groceries and we buy a lot of groceries so Im very pleased with all the room it has. It has a very nice appearance to it. When family and friends come over, they comment about how nice it looks. It was very affordable and very much worth it. I love my refrigerator. I definitely tell friends and family to go check out the prices. Theyre nice and affordable.
Publicado: March 9, 2016
Angela of Charlotte, NC
Fuente: consumeraffairs.com

Is great brand and clean and dry very well my clothes, is very impressive h
Is great brand and clean and dry very well my clothes, is very impressive how this machine are working. The shape is very outstanding and trusted very effective, expensive. I cant live without this two machine. I recommend to everyone.
Publicado: December 21, 2015
Luz of New Smyrna Beach, FL
Fuente: consumeraffairs.com

No problems at all in 15 years including heating element which is the most
No problems at all in 15 years including heating element which is the most common failure. Clothes are dried exceptionally well and lint free for the most part. We have used extensively. Would buy again. I would highly recommend and would replace in kind when needed. Great value considering competition and features actually used. Too many others have features never used and therefore useless for the money. More than adequate for my needs. A good bang for the buck and very reliable. We use several times a week with all clothes.
Publicado: July 9, 2016
Henry of Eagle, CO
Fuente: consumeraffairs.com

Kenmore Elite (cough!) model 795.72182312 2 drawer freezer - We bought this
Kenmore Elite (cough!) model 795.72182312 2 drawer freezer - We bought this refrigerator in early November 2013, and we took delivery in December. First, water and ice formed on top of freezer drawers. Sears said its because I wasnt opening freezer enough, but it was water leaking from dispenser. Repairman said motor was frozen and that wasnt covered in warranty. Jan 2015, same thing with fridge. Water leaking down front on floor and freezer drawers. Paid $2400 for what? Now another repair call, and limited relief from lawsuit! Sears sucks! I bought my last appliance from them.
Publicado: February 4, 2015
monica of Ellisville, MO
Fuente: consumeraffairs.com

I purchased a Kenmore refrigerator and other Kenmore appliances when remode
I purchased a Kenmore refrigerator and other Kenmore appliances when remodeling my kitchen in 2010. The shelves in the refrigerator door are very thin plastic and Ive had to replace both shelves now. The cost is $48.00 per shelf. I think that it is unacceptable. It is just not well designed. It also takes too long to get the replacement parts. I am not a satisfied customer and the parts customer service person I spoke to only said shed make a note in my file.
Publicado: December 1, 2015
Janice of Montgomery, AL
Fuente: consumeraffairs.com

Both washer and dryer are large capacity loaders, energy efficient, they ha
Both washer and dryer are large capacity loaders, energy efficient, they have multiple heat settings, affordable priced. I would recommend them. I can load this washing machine and dryer to the max and the clothes come out clean and bright, they dont take long to dry. I can dry on low as efficiently as if it were on regular and save money. Plain white enamel, they have simple knobs with 3-4 different laundry and dry settings. They both hold large capacity laundry batches. They are valuable to me as they were not expensive and they keep the cost down per load because they are both energy efficient. They both have special features as far as bleach dispenser and fabric softener dispensers go.
Publicado: August 7, 2016
Laurie of Freeland, WA
Fuente: consumeraffairs.com

The refrigerator is very reliable, keeps the food fresh and very cold too h
The refrigerator is very reliable, keeps the food fresh and very cold too however you set it. The ice machine I just love, must be because I love ice. It can fit whatever you buy to put in it. Also if you cook and keep food as left over nice size to store just about anything. Even the freezer portion load it up with meat and veggies. Very clean on the outside, great smell on the inside. I recommend to any and everyone. Just make sure you choose the one you want. Its really up to you. The value is worth a lot but if you want nice things in life you have to spend money but I can guarantee you, if you get it you wont return it. Ive had mine for 3 yrs now still looks brand new.
Publicado: June 3, 2016
Candyse of Fl, Orlando
Fuente: consumeraffairs.com

Its performance is great! Enough room for everything and dries faster than
Its performance is great! Enough room for everything and dries faster than most other dryers. I am really happy with the way it works and am beyond satisfied with its performance. I do believe it is reliable but have had some minor issues with it. Other than some minor issues it is great. I love the way it looks. That is one of the reasons that it was picked. It is a very good looking machine and would pick again solely on its appearance. The performance and other features are definitely more than what is on standard machines so the price is worth the value to me.
Publicado: October 25, 2016
Kelly of Ontario, CA
Fuente: consumeraffairs.com

Compramos el horno de pared doble Sears Kenmore Elite y el problema es que
Compramos el horno de pared doble Sears Kenmore Elite y el problema es que cada vez que el horno pasa por el ciclo de limpieza, el horno no funciona. Esto ya ha sucedido 3 veces y hay que sacar el horno de la pared (recinto) y golpear o reemplazar el interruptor térmico para que el horno funcione. Tenemos un seguro a través de Consumers Power y ellos vienen a arreglar el problema, pero definitivamente hay un grave defecto de diseño en el horno. Llamé a Sears y me dijeron: la garantía de 1 año ha expirado y que tenga un buen día. Nunca más compraremos en Sears.
Publicado: September 11, 2012
Steven of Harrison Twp., MI
Fuente: consumeraffairs.com

Kenmore refrigerators are the best in my opinion! Great cooling everywhere
Kenmore refrigerators are the best in my opinion! Great cooling everywhere including the fast making ice maker and water dispenser - Always cold. I enjoy having the lights in the freezer area too.
Publicado: October 9, 2015
Lisa of Kingman, AZ
Fuente: consumeraffairs.com

El peor lavavajillas que he tenido. No limpia, siempre hay que limpiar los
El peor lavavajillas que he tenido. No limpia, siempre hay que limpiar los chorros de agua. La junta de la puerta del detergente se deslizó en la primera semana. Siendo yo fontanero profesional, no compraría más Kenmore y además no llamaría para que le hicieran ninguna reparación ya que no vale la pena el tiempo, la agravación de escuchar a un técnico explicarme que las cosas no están garantizadas o escuchar opiniones que no tienen sentido. Marca basura.
Publicado: January 22, 2020
M. M. of Hopewell Junction, NY
Fuente: consumeraffairs.com

I purchased this $2300 refrigerator in 2011. It has had one repair already
I purchased this $2300 refrigerator in 2011. It has had one repair already and is scheduled for another repair this month. During this repair, the man stated the dryer unit failed. He repaired that and then stated that the computer board may need to be replaced as well; he did not do that, as it reset. Well, that was wrong as the freezer continued to not be as cold as it should. We go out of town for 2 weeks and the entire unit lost its cooling power. Get this... The temperature rose to 80 in the inner cabinet as well as the freezer so I had to remove all food and try to clean out the smell.When I called for service, I was told the earliest they could come was 7, yes, 7 days later. Why would they take so long for such a vital part of a household? They are due here in 5 more days as we live with two ice chests and no items that need to be refrigerated. I am not sure what the outcome will be of this visit, but I am seriously considering junking it and buying something else. I can not trust it to work properly. With holidays around the corner, I dont want to lose more food. I am not at all happy with Sears products. I feel that they have just shifted to the cheapest versions possible to maintain the highest profit margins they can. If appliances are so poorly made and require continuous repairs, maybe they should get out of the appliance business.
Publicado: November 8, 2013
Kathy of Lutz, FL
Fuente: consumeraffairs.com

We bought a $4k elite 4 years ago, $1k per year and it stopped working. The
We bought a $4k elite 4 years ago, $1k per year and it stopped working. The repair service is pretty much what you read all over the internet. Its a joke the selective 4+ star rating their website shows based on customer complaints. This repair and product services is the biggest joke I have ever experienced. It is not my opinion, its fact they are not customer or priority focused now. Unbelievable. So the requirements to click it is my opinion without a selection that it is my experience and factually horrible service is beyond me.Lost all my freezer and fridge food going on four weeks now with empty promises daily my situation will be addressed. According to others I believe we may just have to repurchase another appliance to replace the ** one we paid hard earned money for several years back. Again this is unbelievable dissatisfaction in a long standing customer. Not sure anything action at this point will erase the sad bad service experience in Sears.
Publicado: March 30, 2017
Steve of Martinez, GA
Fuente: consumeraffairs.com

At some point I had a Kenmore fridge and was very pleased with it. It laste
At some point I had a Kenmore fridge and was very pleased with it. It lasted a very long time and I never had any difficulty with it. It performed well in all facets of keeping my foods cold and never had any problems with too much frost in the freezer section.
Publicado: November 28, 2015
Benjamin of Palm City, FL
Fuente: consumeraffairs.com

My Kenmore Refrigerator is small and white with a freezer on top and a frid
My Kenmore Refrigerator is small and white with a freezer on top and a fridge on the bottom. Its an apartment size refrigerator but fits one month worth of groceries. Ive had it for for 9 years and and it runs every day. It is very well made and uses less electricity. Its easy to clean and perfect for one person.
Publicado: April 12, 2017
Bryan of Hackettstown, NJ
Fuente: consumeraffairs.com

Compré este lavavajillas hace unos 3 años y este es el primer lavavajilla
Compré este lavavajillas hace unos 3 años y este es el primer lavavajillas que tengo que nunca tuvo un problema con él romper o mal funcionamiento. Era más pequeño, pero normalmente podía lavar toda la vajilla en un solo ciclo, en comparación con mi anterior lavavajillas. Tenía más espacio para los platos y menos estética para hacerlo más ancho y ocupar menos espacio. Es simple pero agradable a la vista, no necesita mucha estética como la mayoría de los lavavajillas para que parezca desordenado. Yo recomendaría este lavavajillas a cualquiera que necesite algo simple, pero de aspecto agradable y hace el trabajo. Por el precio, este es un lavavajillas grande y fiable que tengo. Nunca he tenido un problema con este lavavajillas a diferencia de todas las otras marcas que he tenido que se rompieron en los primeros 6 meses.
Publicado: September 8, 2016
Roy of Piqua, OH
Fuente: consumeraffairs.com

Deja de funcionar si apagamos el horno y lo volvemos a encender, para ajust
Deja de funcionar si apagamos el horno y lo volvemos a encender, para ajustar la temperatura o si tenemos que volver a poner algo porque no se ha hecho como pensábamos, la única manera de arreglarlo es apartar el pesado horno de la pared para llegar al enchufe, desenchufarlo, volver a enchufarlo, lo que es un desastre ya que es demasiado pesado para mí.
Publicado: February 2, 2021
Sheila of Bennington, VT
Fuente: consumeraffairs.com

It is a very good product. It looks shiny and stylish. It is slim. Not bulk
It is a very good product. It looks shiny and stylish. It is slim. Not bulky like others, yet it contains many space for storage. The freezer side have plenty of space and many adjustments for the temperature. It is a totally worth product.
Publicado: November 7, 2016
Lily of San Francisco, CA
Fuente: consumeraffairs.com

In July and September my refrigerator was repaired because it wasnt maintai
In July and September my refrigerator was repaired because it wasnt maintaining proper temperatures. Right now (6 Nov) I cannot get the freezer to get below 10 degrees. It is so painful to take everything out of the refrigerator.
Publicado: November 6, 2013
David of Detroit, MI
Fuente: consumeraffairs.com

Compré un horno eléctrico deslizante hace unos años y, desde entonces, l
Compré un horno eléctrico deslizante hace unos años y, desde entonces, la temperatura del horno no es correcta. Tuve que comprar varios termómetros de horno para ver cuál era la temperatura correcta. El problema PRINCIPAL que realmente me asusta es que el botón de autolimpieza se activa con demasiada facilidad y bloquea la puerta del horno. Se calienta mucho y es muy difícil apagarlo. Una vez, tuvimos que llamar a un vecino para que nos ayudara a sacar la unidad para apagarla. Odio que los botones digitales estén situados en la parte delantera, así que cuando limpio algo, se activan TODAS las funciones y tengo que pulsar constantemente el botón de parada para anularlas. Nunca compraré otro producto Kenmore después de mi experiencia con este horno.
Publicado: October 23, 2018
Susan of Walnut Cove, NC
Fuente: consumeraffairs.com

Works good, holds a lot. Ice maker and cold water are nice features to have
Works good, holds a lot. Ice maker and cold water are nice features to have. Quality product. Would be happy to purchase Kenmore products anytime. Takes up a big space but understandable with all it holds. Takes care of the needs of my family and has great features. I would highly recommended it to my friends and family. Its a huge metallic box. It is stainless steel. The freezer is humongous as well. Can easily fit a whole side of beef if you remove the shelves.
Publicado: August 5, 2016
Neil of Port Saint Lucie, FL
Fuente: consumeraffairs.com

My Kenmore washing machine is only 17 months old and the transmission is do
My Kenmore washing machine is only 17 months old and the transmission is done. Basically the machine is finished - too expensive to fix. More importantly. Sears will do absolutely nothing unless of course I want to throw a little more money at them. What has happened to product quality and caring for the customer.
Publicado: July 28, 2014
Anne Marie of , NY
Fuente: consumeraffairs.com

El frigorífico Kenmore es bonito, tiene mucho espacio en el cajón de la f
El frigorífico Kenmore es bonito, tiene mucho espacio en el cajón de la fruta y tiene máquina de hielo. Es muy fiable y funciona muy bien. Me gustaría que tuviera una máquina de hielo en la parte delantera, más congelador y era de lado a lado. Pero aparte de eso, siempre me ha gustado la marca y ha sido un gran producto con cualquier cosa de su marca. Estoy contento y he quedado totalmente satisfecho con él. Definitivamente lo puedo recomendar a alguien que esté buscando uno nuevo.
Publicado: February 27, 2018
Delana of Cincinnati, OH
Fuente: consumeraffairs.com

Mi Kenmore elite ha sido un regalo del cielo, con problemas de espalda, me
Mi Kenmore elite ha sido un regalo del cielo, con problemas de espalda, me quedé con sólo ser capaz de utilizar los quemadores en mis otras estufas en el pasado, pero con mi doble horno superior, horno de convección inferior, tengo la opción de elegir. Me encanta la fácil autolimpieza, el temporizador de cocción por botón y las funciones de retardo junto con los 5 quemadores de diferentes tamaños, (también vino con una plancha) el quemador del medio es de forma ovalada. El bloqueo de seguridad para niños y las puertas de toque frío son funciones adicionales importantes, por nombrar algunas. No he tenido ningún problema con el horno o las funciones en los 2 años que he tenido mi horno. Kenmore ha sido una marca sólida y fiable durante muchos años. ¡Me encanta mi horno!
Publicado: February 13, 2021
gwen of Torrance, CA
Fuente: consumeraffairs.com

My wife and I built a brand new home two years ago and supplied it with all
My wife and I built a brand new home two years ago and supplied it with all Kenmore or Kenmore elite appliances. As of today the appliances are barely 2 years old and the washing machine has broke, needs a new control panel and drain pump that is going to take a week or more to come in so we have no washer for at least a week. The dishwasher shuts off mid cycle so I have to have somebody come out for that. The tech told me it is probably an issue with the temp of the water so I have to run the hot water at the sink until it gets hot then run the dishwasher. Really? For two years it worked just fine and now that it is malfunctioning that is the solution they give me? The top of our refrigerator freezer door completely cracked and got worse over time until it eventually all fell off into pieces. This happened by simply opening and closing the door. It looks terrible in our brand new $330k home. When I called Kenmore they said that is cosmetic and wont be taken care of. I am beyond disappointed. We spent thousands of dollars and thought that Kenmore was a great brand until this.Update: The control panel Kenmore is sending me for my washer is now delayed by UPS and UPS is now telling me I may not have the part until late next week. Maybe later. So we will possibly go into 2+ weeks without a washing machine. I have called the Kenmore 1-800-4-my-home number several times and I get nowhere. One agent actually told me if the part does not arrive within 21 days then they will explore other options. As if a two year old washing machine breaking and sending us to the laundromat for 3+ weeks is acceptable. Terrible service!!!
Publicado: November 2, 2017
Michael of Fort Johnson, NY
Fuente: consumeraffairs.com

Lava muy bien la vajilla y los cubiertos. A veces las ollas y sartenes tien
Lava muy bien la vajilla y los cubiertos. A veces las ollas y sartenes tienen que estar tumbadas para que se limpien, otras veces no. Me aseguro de enjuagar todos los platos antes de ponerlos en lo que la comida no se pegue si no lo ejecute de inmediato. Se ajusta perfecto al lado del fregadero y tiene diferentes ajustes en él para diferentes lavados. Es alrededor de 36 pulgadas de ancho y creo que 48 pulgadas de alto. Tengo un lavavajillas que es negro con la escritura blanca en él y la perilla gira a lo que el ajuste que quiero. Tiene un ciclo de retardo que se puede usar si no se quiere poner en marcha inmediatamente y un ciclo de secado. Es un gran lavavajillas. Tiene una cesta separada para los cubiertos que se puede sacar de la máquina y 2 rejillas para los platos. La superior es ideal para tazas y vasos. La de abajo la uso para el resto. En la puerta hay un lugar para añadir detergente y aclarar.
Publicado: August 12, 2016
Peg of Buffalo, NY
Fuente: consumeraffairs.com

The Kenmore Refrigerator works well, hasnt broken down, keeps everything fr
The Kenmore Refrigerator works well, hasnt broken down, keeps everything fresh. Its crisp white, easy to clean, perfect in size, not too big or small, fits beautifully in my medium sized kitchen. Plenty of great shelves, great space, and its easy to organize the food. Perfect look for any kitchen. It has great value, its worth the space, look, and storage and cooling capability. The price was right for what its worth. Never shut down on me.
Publicado: March 21, 2017
Teresa of San Jose, CA
Fuente: consumeraffairs.com

Compré un frigorífico Kenmore completamente nuevo 8,2018 y el compresor s
Compré un frigorífico Kenmore completamente nuevo 8,2018 y el compresor se estropeó 9,27,2020. Llamé para fijar una fecha de cita para el servicio y no se presentaron. Ahora mis citas continúan siendo reprogramadas más tarde y más tarde en el mes. ¡Esto ha cambiado cada dos días a través de texto o llamadas automáticas desde el 10,6, al 10,7 al 10,19, y ahora al 10,20! No he recibido ninguna explicación de por qué mis citas siguen siendo cambiadas y ningún acuse de recibo con respecto a una solicitud de servicio para un refrigerador que es un artículo doméstico ESENCIAL.He expresado que tengo 3 niños en mi casa y que estaba comprando hielo para conservar la leche y los huevos en neveras. ¡He perdido el sueldo dejando el trabajo por un servicio que nunca se produjo, además de perder toda mi comida en la nevera y el congelador! No hay cobertura porque no compré una garantía extendida. He pagado 170 dólares para que un técnico externo venga a evaluar y reparar, pero tengo que hacer que un técnico de Sears lo inspeccione. El compresor está cubierto por la garantía del fabricante, pero soy responsable de la tarifa de la visita de servicio - no hay problema, si sólo puedo conseguir que alguien haga el servicio. Nunca me imaginé que en tan sólo 2 años se me estropearía una pieza importante. Todos mis aparatos son Kenmore????
Publicado: October 8, 2020
Theresa of Pennsauken, NJ
Fuente: consumeraffairs.com

Kenmore es una marca que existe desde hace años y en la que confío. La ma
Kenmore es una marca que existe desde hace años y en la que confío. La marca es muy apreciada y el nombre de calidad me hace sentir bien con la compra. El frigorífico y el congelador cumplen con el propósito para el que fueron comprados. Tiene una buena cantidad de espacio para el almacenamiento en el refrigerador, así como el congelador. El congelador tiene una máquina de hielo que hace hielo pero se aglutina. E incluso con un filtro nuevo la máquina de hielo hace hielo que sabe a plástico. Pero espero que el frigorífico dure muchos años.
Publicado: March 2, 2018
Lise of Edmond, OK
Fuente: consumeraffairs.com

Kenmore Elite modelo 790 789 02000 - Compró una casa de 5 años - el horno
Kenmore Elite modelo 790 789 02000 - Compró una casa de 5 años - el horno no funciona - $495.00 para reparar. Necesita 1 encendedor, 1 controlador, PCB principal para ser reemplazado. Esto fue sólo una cabaña de verano, horno rara vez se utiliza y su rompió ya. Tendrá que esperar para reparar o comprar nuevos como todavía tienen 2 Mtg.
Publicado: September 25, 2014
Laurie of Cohasset, MN
Fuente: consumeraffairs.com

No he tenido ningún problema con este lavavajillas. Se encarga de todos lo
No he tenido ningún problema con este lavavajillas. Se encarga de todos los restos de comida en los platos y es muy útil para sartenes grandes y bandejas de galletas. Puedo cargar bastante. Somos una familia de cuatro y mis hijos usan constantemente los vasos y nunca los lavan. Estoy muy contenta. Me gustaría que viniera en un color diferente, sin embargo, estoy agradecido de que los anteriores propietarios dejaron esto atrás. Es anticuado. Sin embargo, no hay óxido o elementos rotos en él. El desgaste en él ha durado. No dudaría en comprar o sustituir este lavavajillas por otro de la misma marca.
Publicado: August 11, 2016
Marie of Methuen, MA
Fuente: consumeraffairs.com

So the Kenmore Elite refrigerator that we purchased not so long ago is now
So the Kenmore Elite refrigerator that we purchased not so long ago is now breaking down. By breaking down I mean the ice machine part is physically breaking apart. I just found a huge piece of plastic in my glass. Please be aware if you own one!! Just imagine if the plastic was smaller...
Publicado: May 24, 2017
Jamieson of Cheyenne, WY
Fuente: consumeraffairs.com

Kenmore Modelo 790.92202014 Fusión del control del horno - Compré esta co
Kenmore Modelo 790.92202014 Fusión del control del horno - Compré esta cocina a principios de 2011 como una actualización de mi antigua cocina Whirlpool. Poco después de que saliera de la garantía, la unidad de control del horno falló. Llamé a un reparador y me pidió una nueva y la reemplazó. Menos de un año después, la unidad volvió a fallar, así que envié la unidad defectuosa de vuelta al proveedor y me enviaron un reemplazo. Esto duró de nuevo menos de un año hasta el 3-2013, sólo que esta vez hizo saltar el disyuntor (nunca lo había hecho antes). Al quitar la tapa trasera, me horrorizó encontrar el enchufe del horno que se conecta a la unidad de control fundido. Sólo puedo decir que me alegro de que no haya provocado un incendio. Estoy escribiendo esta queja para advertir a la gente de un posible peligro de incendio. Voy a desechar esta cocina.
Publicado: March 24, 2013
Steve of Three Oaks, MI
Fuente: consumeraffairs.com

Esta máquina fue comprada en Sears hace años y todavía va fuerte, reempl
Esta máquina fue comprada en Sears hace años y todavía va fuerte, reemplazado la bobina de calentamiento, pero aparte de. que todavía funciona bien. Lo he tenido más de 10 años, la mejor compra nunca, siempre han pegado con Kenmore, bien hecho lavadora.
Publicado: May 10, 2020
Carolyn of Memphis, TN
Fuente: consumeraffairs.com

Never had any problems with it. Did a very good job on all dishes and pans.
Never had any problems with it. Did a very good job on all dishes and pans. QUIET! Would not trade it for anything. I love my dishwasher. Holds a big load or small and does a good job washing both. Holidays I really love my dishwasher. I can fill it up and not worry about pulling dirty dishes out. My dishes and pans come out clean every time. It fits within with the rest of my kitchen and there are many design to choose from. If you are remodeling or need a new dishwasher for your old kitchen there is a style to choose from. The value of my dishwasher now that I have had it a few years is priceless. If I had known what I was getting and how good it was (YES), I would have paid a lot more for it. I have had other dishwashers and to me they was all the same until I got this one. They are not the same.
Publicado: July 28, 2016
Sharon of San Diego, CA
Fuente: consumeraffairs.com

It washed dishes, sometimes food would be melted onto the container. The in
It washed dishes, sometimes food would be melted onto the container. The individual cycles were not used much, just the standard, but it did pretty well for its price point. I didnt like the color, should have gone with stainless models. The size was very nice. It had enough space for all of our dishes and cutlery. We were able to for several days and dinners worth of food onto the dishwasher and they almost always came out equally washed and clean. I did not end up liking the color very much. It was not the color I originally wanted, but I bought it on sale so I went with it. Inside and out, I would have preferred something like a stainless steel look for the dishwasher. I was happy with the value, especially because I was able to buy it on sale. The dishwasher never broke down or needed repair so it was a quality purchase. I would recommend it again if it was a dishwasher that was on sale.
Publicado: June 11, 2016
Charles of Black Mountain, NC
Fuente: consumeraffairs.com

I had a Kenmore refrigerator many years ago that outlasted itself by many y
I had a Kenmore refrigerator many years ago that outlasted itself by many years. My family and I loved it. When it came time to be replaced, there were no models at that time that would fit in the assigned space since I had my kitchen remodeled.
Publicado: November 19, 2015
Carol of East Meadow, NY
Fuente: consumeraffairs.com

I was not impressed with this washer. I went from using a regular washer to
I was not impressed with this washer. I went from using a regular washer to this and the clothes didnt come clean even on a small load. The washer barely filled with water and some of the clothes came out of the wash still having dry spots on them from where they didnt even get wet. This washer was not reliable because the clothes didnt get clean and some didnt even get wet. Not to mention that it takes over an hour to wash one load of laundry. The washer looked nice but it just didnt wash good. I sent it back after 3 days of use. The metal that the washer was made from also seemed kind of flimsy. I paid over a thousand dollars for the washer and dryer set and was very disappointed. It used very little water and didnt even cover the clothes leaving dry spots on some of the clothes from not agitating very well.
Publicado: August 3, 2016
Melinda of Woodstock, GA
Fuente: consumeraffairs.com

Tengo un horno de cerámica hace un mes y ahora tengo un gran problema. Hay
Tengo un horno de cerámica hace un mes y ahora tengo un gran problema. Hay un cortocircuito con el control y un mal olor como a plástico quemado. Llamé al servicio técnico pero, por desgracia, me dieron un plazo de servicio de siete días y su ingeniero no responde en absoluto a su móvil. Realmente, tienen un buen producto pero si el distribuidor sigue así, perderán el mercado saudí. Me gustan los productos Kenmore pero no me gusta el distribuidor. Por favor, ayúdenme. Gracias de antemano.
Publicado: July 27, 2012
Mohammad of Riyadh, Other
Fuente: consumeraffairs.com

I love my Kenmore refrigerator because I feel confident to leave all of my
I love my Kenmore refrigerator because I feel confident to leave all of my food and I love how save the electricity is. I feel lucky got this excellence and good quality. I love to recommend this to my friends and family, mini fact I did to talk about how good our refrigerator is. Happy and contented having this brand right now. Kudos to the company and the one who made this. Thanks!
Publicado: November 14, 2015
Wheng of Los Altos, CA
Fuente: consumeraffairs.com

I too spent my hard earned dollars to purchase a Kenmore bottom mount refri
I too spent my hard earned dollars to purchase a Kenmore bottom mount refrigerator. Within two years of purchase it began leaking water onto my kitchen floor. Not only is this problematic in terms of actually having cold storage for our food but a hazard. Having been unaware of the problem, I took a major dive on the kitchen floor when I slid in the puddle of water. One more reason to BEWARE of purchasing from Sears. Seems like Sears will not change their irresponsible practices until a law suit forces them to do so.
Publicado: November 24, 2013
Carol of Scranton, PA
Fuente: consumeraffairs.com

Tengo un side by side. La sección del refrigerador es pequeña para los ar
Tengo un side by side. La sección del refrigerador es pequeña para los artículos más grandes. El siguiente refrigerador va a la sección inferior del congelador con el refrigerador en la parte superior. Nos gustaría que la sección del refrigerador fuera lo suficientemente grande como para poner cajas de pizza, etc.
Publicado: September 8, 2019
Gil of Pickerington, OH
Fuente: consumeraffairs.com

I was very satisfied with my old refrigerator. I wish I had stick to the on
I was very satisfied with my old refrigerator. I wish I had stick to the one when I bought my new house. My current gave so much problem! I spent very little for my old men more and never had any problems.
Publicado: December 2, 2015
Mayra of Citrus Heights, CA
Fuente: consumeraffairs.com

I had a Kenmore for about 15 yrs and it was still going strong. Unfortunate
I had a Kenmore for about 15 yrs and it was still going strong. Unfortunately it was ruin on a move from MA to FL. It was great, never had a problem. I ended up buying a Maytag in FL, and have had problems with it constantly. Ive been through 3 replacements, its so bad. My next fridge will be a Kenmore.
Publicado: November 8, 2015
Maria of Winter Springs, FL
Fuente: consumeraffairs.com

I have been a Kenmore user since I started buying appliances. I have never
I have been a Kenmore user since I started buying appliances. I have never been disappointed, and so I keep coming back. This low efficiency washer is awful. Hardly adds any water at all; its washboard does its best to destroy and rip up your clothes (I have pictures if anyone doubts me); this cycle is so long that you cannot do more that one load of washing in one night. Laundry used to be fun for me. And BTW, clothes are still not clean.
Publicado: February 19, 2022
Karen of Boerne, TX
Fuente: consumeraffairs.com

Visa MasterCard

Site Secured By The Website Guardian
CIMA