I own a GE counter-top sensor microwave oven model #JES1451, which was only 2 years old. At 3:00AM, I woke to a room full of smoke and a burning plastic smell. I immediately rushed to the source which was my microwave oven. It was going by itself and the panel read sensor error with smoke billowing out of it and flames erupting. Luckily, I had a fire extinguisher handy. I had never had any problems with this microwave prior to this experience. I cringe at the thought of what could have happened to my home and my family sleeping upstairs if I hadnt been nearby.

A few years ago, I purchased a brand new GE microwave oven. A week ago the microwave oven stopped working. I contacted an Appliance Repair company for repair. When the tech came & disassembled the microwave oven, he discovered pliers inside the oven. We took pictures of it (BTW, it wasnt the cause of the problem). I contacted GE to alert them of this & they told me that the robots that assembled the microwave oven probably dropped it in there. Then they said they will send a tech to my residence to investigate. I told them that the pliers was removed & the microwave oven is fixed & assembled. Nonetheless they sent a tech anyway. I told the tech what his Customer Service said & he said he wasnt surprised about the tool being inside an appliance from GE & GEs response. In summary, I would not recommend purchasing any GE products. They proved their products are a safety hazard & they dont care about the consumer nor their safety. All they care about is taking your $$$.

I have many other things to do other than to voice my extreme and total displeasure with your company. GE - Huge Company, Small Customer Service. We purchased a GE microwave oven from ABT electronics in about August, 2013. In October, 2014 we had issues with the fan remaining on while the door was closed. Called GE. They said the unit was out of warranty by about 2 months. We felt that was a short period of time and that we called as soon as the issue became chronic.Had three service calls where the techs tried to fix a simple problem. First tech walked through our living room with dirty boots. Didnt fix the problem. Messed up our carpet. Bad attitude. Second call, two techs couldnt fix the problem. Said it was a door issue and they made some superficial adjustments. Problem not fixed. Third call, two more techs. Same result. In the meantime I tried to convince GE that I didnt want another service call. I wanted a new unit. No luck. I was offered a discount to purchase a new unit for around $300 or so. Im sure they spent more money on service calls than a new unit would have cost in terms of dollars and the reputation of one of the worlds biggest companies.Now, the fan for the unit stays on almost all the time after the cooking is done. Is this the best GE can do? If so, thats pretty sad. Tried to reach someone in sales who would get it. No such luck. DONT BUY GE AND IF YOU HAVE ISSUES DONT RELY ON A FACELESS, CLUELESS CUSTOMER SERVICE DEPARTMENT TO HELP IN ANY MEANINGFUL WAY.

One needs to be a contortionist to replace the under light bulbs on this microwave. It is a TERRIBLE design. Why werent the sockets placed so that the prong holes could be visible? One has to do a back-bend over the stove top and then the socket holes are still not visible. DO NOT BUY THIS MICROWAVE. DONT BUY THE STOVE EITHER. IT IS DANGEROUS. THE KNOBS TURN EASILY AND OPEN THE GAS.

Bought a GE microwave and arranged to have it installed. Kept it in sealed box for 3 days until installer appointment. Opened box to find a crease (dent) in door. I phoned in to the GE warranty depot and they informed me that I only had 48 hours to report and as such was out of luck. They indicated that it is clearly stated in the Appliance Manual under the warranty section. Too bad that the Manual was in the sealed box. No warning on the outside of the box. On top of that the individual that I spoke to at the Warranty Depot was very rude. No more GE Appliances for me. Be forewarned.

Had to purchase new oven. General Electric appliances are JUNK.

I just built a new home and opted for all GE Slate appliances. No problems so far with microwave, fridge, and stove but the dishwasher has never once been dry or cleaned all dishes. We have had it a little over a month! Today when I went to run it, there was mold growing! I had a KitchenAid for 9 years and never once did any of this happen. From reading other complaints, it looks like Ill be living with this for some time. I will never purchase GE again.

We bought our new home 4 years ago & bought upgraded GE Profile appliances. To date, the gas range has been serviced 3 times, the refrigerator too many times to remember & now my dishwasher pump has gone out. We found out the pump just cannot be replaced, but all hoses, etc. must be purchased as well. GE is CRAP & I will never even consider purchasing anything from this company again. Knowing it was bought out a few years ago by Whirlpool (I believe) but still remains under the GE label - consumers BEWARE.

Remodeled our kitchen back 6-7 years ago and bought GE Profile appliances from Home Depot... bad mistake. The microwave/convection oven came as one unit and now due to paint peeling on the microwave interior - inside top and sides we need to replace the entire unit to the tune of $2,500 plus. I called Home Depot and asked if there was a government mandated recall on the item... and they asked if we purchased the extended warranty. What? Does anyone know of a recall or class action suit on the following item: GE Profile Model: PT970SMISS. Manufactured December 2007.

The microwave has done its job for the last 15 years and is still going strong. It isnt perfect, but it serves me well. The microwave is fine, but I am no longer a fan of GE products. The design of their stove makes it difficult to clean. I had to pick their dishwasher because it was the only one with the right dimensions. It does a terrible job cleaning the dishes.

My microwave also began peeling under the glass within a few years after we purchased it. I contacted GE and they claimed they never heard of that type of complaint before and there was no recall. I knew it could not be just my appliance that was doing this. It is peeling A LOT under the turning dish, but unfortunately I cant afford to buy another oven/micro appliance now. When I can IT WILL NOT BE A GE!!!

First Profile microwave/oven caught on fire. Was replaced. Front panel on Profile refrigerator not reacting to touch. Repairman said that this model had problems. Fixed it - cost over $100.00. Dishwasher (Profile series) not worth the cost of heating the water to run it. Cleaned dishes by hand. Stove top died - not reacting to touch. $90.00 for repairman to visit us, and another $60.00 to tell us what was wrong. A lot of money for inferior products.

My Microwave that is four years old suddenly wont heat anymore. It still runs but there is no heat. They told me its out of warrantee already. The repairman says its the magnetron and it costs $600 to replace! The oven microwave combo unit is $1500 altogether to replace. I bought another Walmart microwave for $47 and it works great! GE will not replace or fix it. They dont stand behind their products and are not helpful on the phone. I will never use a GE product again.

On 05/20/2014, our GE microwave over the stove unit burst into flames. My wife was using timer and walked away then turned around and heard the microwave fan start (spontaneously). Then she observed flames/smoke reflected in the Microwave window. She observed the interior of the microwave was aflame. The fire was extinguished with a rag & water. The burning items appeared to be plastic/insulation. The fan from the microwave was with the burning insulation on the rotating plate. Had this unit only 14 months during that time the microwave fan would turn itself on for 3 minutes and then turn off all by itself. Happened twice in 14 months. Glad we were at home and were able to extinguish the fire. Called Lennar the builder who put this unit in to take pictures and check electrical. Was told the GE unit was bad to call GE. I know this will be a hassle as others have had this same problem with not so good results.

We purchased a GE over-the-range microwave oven last November 2010 and it was installed in February 2011 when our addition was finished. Last week, it decided to stop responding to instructions. When the door is closed, it just continues to run--the turntable turns, the light stays on and the fan keeps running. It will respond to instructions, but when we want to shut it off if the door is shut, we have to unplug it--which is a real pain because it is over the range.We have an old microwave that was my wifes parents and it still works fine even though it is about 20 years old. The new one stops working in a little more than a year which is not acceptable. We contacted GE and were told that we would have to pay over $100.00 to get the thing fixed. I dont think so. We will not purchase anything GE again.

My microwave is only 5 years old. It is burned out electronically. I would never buy another GE product. My GE Profile stove needs a $300 repair after 4 years.

Our Profile over-the-range microwave failed after 2 years. (Warranty was for one year!) One day it suddenly died. The repairman ($100) said repeated twisting of the wire from the oven to the door (which contains all the electronics) is inevitable with opening and closing. The wire often breaks within its insulation: a bad design fault. No question of replacing the wire; we would have to order a new door, for nearly $400 plus $200 for installation, which requires 2 service technicians. This is more than the cost of a new OTR microwave. He advised us to get one with the controls beside, not in the door. Unfortunately GE is the only company that makes a microwave in the same colour as our range.

Its a over the range model & came with a house purchase. It’s worked flawlessly for over 5 years now - even after being left with no air conditioning in FL for months on end. The only thing I could think to make it better is making it easier to choose longer length cook times. Button for half min & dial for all the rest can be irritating for your 16 min food.

I moved into our house about 27 years ago, and have had to replace every single appliance except the microwave. The oven, fridge, washer, dryer, dishwasher—all replaced at least one time over. But this 90s GE microwave keeps humming along. I really should replace it just because it is this awful off-white color and everything else in our kitchen is part of a beautiful stainless steel/black/white scheme, but it is actually built right into a cabinet and I fear I will not be able to get another microwave in there. The only gripe I have about its performance is the fan comes on and roars full-blast anytime the stove or oven is on. It is so loud its difficult to talk over.

Fact no. 1: On 02/25/07, I supplanted a burnt-out 12-year old Kenmore microwave oven. Regretfully, my replacement of choice is a GE JES1456WJ02 unit acquired at Home Depot in Cumberland. At that stage, my spouse was afflicted with an advanced case of Parkinsons disease, and eventually, I had her concerned caregiver reporting having found chips of paint spread on food extracted from the new oven. From that point onward, I established a close watch of the infamous appliance, after confirming that the chipping paint originated from the roof of the GE oven. But I withheld from filing a claim with GE at the time because my wifes health deterioration absorbed all my attention.Fact no. 2: But on 12/12/09, a couple of months after my beloved one passed away, I decided to take the oven to a Home Depot claim department where they immediately agreed to replace the defective unit for another one of similar characteristics. With a sigh of relief, thinking that I had taken care of the problem, my assumption was incorrect.Fact no. 3: Today, 10/28/11 in fact, I discovered chips of paint floating over a plate of soup extracted from the GE oven. I was aghast! I couldnt believe it! Still, further inspection determined that the lousy internal coat of paint is likewise peeling off from this monstrosity appliance manufactured by GE.

My GE microwave oven turns on by itself. The GE microwave oven model number: JVM1540DN1WW. The serial number is: RS903539B. My GE microwave oven turns on by itself usually as if the one minute express button was pressed in. This has been occurring for about 2 years and has been doing this normally when the air conditioner is not turned on. It appears this is a humidity issue. All summer it has been working fine. As the weather has started to be lower and we turned off the air conditioner, the problem has come back. When the temperature rises and we put the AC on again the unit will work fine. We live in Florida and it can be humid outside but with the AC turned on the humidity is lower and the microwave will work fine.

I have bought 3 GE appliances in the past 2-5 years, a microwave, dishwasher and oven with cooktop. They are all white and the white paint is peeling off. The microwave is the worst with most of the paint gone from the metal around the window inside. I will never buy another GE appliance again. To have 3 different appliances with peeling paint signals a definite quality control problem in the company.

I also bought a counter top GE microwave oven model jes1451dn1bb that turned itself on and then stated a vegetable sensor error. I did not trust it after this and when I plugged it back in, it stated a keyboard short had occurred and that I may need service. What I need is a non-GE microwave oven that works longer than 18 months. Prior to this machine, I had bought the same model back in 2003 and the same thing happened; The machine turned itself on and stated a popcorn sensor failed. This was back years ago and I complained to GE but never heard from them. This problem has been going on for years and they do not give a ** about the consumer who lives with this machine. I complained tonight about my second microwave and unless a miracle happens, I will never buy another GE product again in my life!

I purchased the micro from Sears. This is the replacement for one that was provided by the builder. The G.E. now needs replacement. Will work for limited periods of time. I have used it more than my stove to cook chicken, beef and whole meals. I will be replacing it with a new G.E.. The current one has lasted more 10 years with very heavy use.

Our microwave caught fire today and burned our kitchen, stove top, & attic. According to the Fire Captain, the cause of the fire was the GE microwave panel shorting out. Had my mom not been standing right there as it happened, our entire house would have surely been a loss.

Not even a year after purchase of new cafe series dishwasher, stainless lining rusting. Service called, GE tech agrees rusting of lining, GE warranty says not under warranty. Ive replaced screws that show signs of rust with aftermarket stainless screws. Cafe oven has had three front knobs just fall off - two were repaired under warranty and had to purchase extended warranty on third because it was more cost effective. Cafe Refrigerator had drain plate in back of unit completely rust away, tech knew what problem was before he stepped foot in my kitchen, he told us this was common. He caulked some sensor inside fridge box during service, I asked why, his response was its a design flaw and unit will operate better with this modification. Oh and redesign the ice dispenser, its tilted towards the back of the freezer and the ice is dispensed out the front.

Less than three years ago, I purchased a microwave oven wall unit to replace an existing unit. Due to the size of the built-in cabinet, I was limited in choices. The cost of the unit was $2400. A few months ago, the interior wall of the unit began rusting and the enamel is peeling. I contacted the customer service dept via e-mail on their site. I was asked to send pictures and then informed that I should stop using the unit immediately due to the danger of arcing. I was also told that because I did not purchase the extended warranty, the best that GE could offer me was a new unit for $800. I asked for names of warranty companies and was given one name and number but told there were others that also offered the same service. I called this company and they clearly told me that the peeling and chipping was a manufacturer’s defect and would not have been covered by an extended warranty had I purchased one from any company. Then I contacted the GE repair service center and spoke with them. The man who answered explained that this is a cosmetic problem and that there was no danger of the microwave arcing unless there was less food in the microwave than the size of the area that was chipping. I am very disappointed in the response of GE, the pressure placed on me to make a decision in 7 days or the offer would be withdrawn, and the fact that the service department and the consumer service (complaint) department gave me entirely different responses to the same information and problem. I will probably have my cabinet rebuilt to avoid having to replace this unit with another GE appliance. Who would pay $$1600 for the use of a microwave/oven unit for less than three years? Unfortunately, GE seems to be the only company that makes a unit that fits the existing cabinet in my kitchen. Disappointing to say the least.

I had to place a new order for a trim kit for my new microwave oven since the original one did not fit. I was told it would be 5 days when I placed the order, then it was backordered for 5 days, then 7 more days and now 3 more days. When will I receive the product that I have paid for 3 weeks ago?

Our over the range microwave oven is under warranty and broke twice. They refuse to replace it. It was fixed the first time but its broke again and the only service tech refuses to come to our home to service it anymore. Its been a nightmare and still not resolved. We will never purchase another GE Appliance ever again!

I had a GE microwave that matched the GE range that was already in my condo when I moved in. When the range died, I got a new, matching microwave too. I like the way it works, the controls are intuitive and its easy to clean. No complaints.

I recently purchased a GE Profile 1.9 microwave oven from Home Depot less than a year ago. Last week I went to remove something that I had cooked and went to close the door and it would not stay shut. I ended up getting some masking tape to try and tape it shut in order to keep the light from staying on and burning out until morning when I could get a better look at it, thinking that it had to be something small that could be taken care of without any problem. Hinge adjustment, something getting in the way that I couldnt see, etc, etc. Wrong! I have been over this door with a fine tooth comb and there is nothing that I can see that is preventing it from staying closed, not only that but according to everything that I have read, I am very lucky that I didnt get fried while trying to figure out if the latching mechanism was functioning correctly. I am not even going to go through the long drawn out process of dealing with GE over this due to the simple fact that I have been there done that with my dishwasher that showed up with the front panel dented a few years back from the factory and I ended up blaming the place that I had purchased it through instead of GE and have since found out by reading other complaints that this seems to be something that is not unusual when it comes to GE appliances. I spent over 1100.00 dollars on the dishwasher and they only replaced the panel instead of giving me a new one, and I have never been satisfied with the way that it operates, and it was a very long and drawn out process and I am just not willing to spend the time again on another one of their products. It is unfortunate that we have entered a time where customer satisfaction means nothing, and the days of caring about having repeat business from a satisfied customer are over. The prices continue to rise on the things that we have become to depend on and cant seem to live without, but the quality and workmanship have not only diminished but also present safety threats. I will never purchase another GE anything and I am looking forward to the day when we all have finally had enough of this and do something that makes these companies stand behind the products that they sell and quits ripping the consumer off. Its rampant across the board no matter what you buy, and there should be laws in place in order to keep it from happening. We have laws for everything else, why not have a couple that protect the consumer and their pocket books.

We purchased this new 8 years ago however the problems started after about two and a half years of use. I called GE when the paint started peeling off of the door of the microwave. They asked me if I cooked salty foods. I cook bacon in the microwave. They told me my only option was to buy a new door and have it installed. It was $250 at the time. I did not have the money or desire to fool with it. I continued to use the microwave and it has continued to degrade. Now eight years later there is so much metal showing that we decided we must do something. It is unsightly and very difficult to clean because its rusting. Ive been expecting electrical arcs to occur and the microwave to catch on fire. It hasnt done that. It has continued to cook the food. The entire metal area on the door is without paint. There are other large areas of metal and rust inside on the bottom of the microwave. The entire vent panel is without paint and rusted. We also had to have the control panel replaced twice. It was covered once under the warranty and once it was not. We also had to replace the element in the oven which is used rarely. To replace the microwave and oven combination now would be $3,500. When I do replace it I will replace it with a different brand.

Over-the-range microwave failure (model JVM2052, manufactured Dec. 2010) was purchased and installed professionally in March 2011. Total cost is $546. First, the fan failed in about June 2012 and I thought I can live with this. In Sept. 2012, the unit failed, but the interior light and clock still work. I paid $97.00 for a service call from the dealer, and the tech said the power source failed(?). Estimated parts and labor for repair is $370. So, I will buy a new unit (not GE) and pay about $150 for delivery and installation and take away this GE unit. I live in Morris County, NJ and this is not a rural area! GE service rep whom I called said GE doesnt service this area and to look in the yellow pages for an authorized dealer. I called again and got the name and address of the president of GE Appliances, and I am going to write about this product.

We purchased our Adora over-the-stove microwave oven from Home Depot. The Adora brand is made exclusively for Home Depot and were sold on its special functions and value. Well now, 3 years later, this exclusive models glass fogs up when we use it. There are only 2 of us living at home. We use it maybe 4 or 5 times a day. A microwaves typical lifetime is 9 to 10 years. Also, by the way, when we turn on the fan to highest, it sounds like an express train hurtling through our kitchen. Our dog had a heart attack and died the first day we operated it. No he didnt. We dont even have a dog. But you get the picture.

The microwave oven that I’ve been using works real well and it’s not that expensive. It’s also a convection oven at the same time. The only reason I didn’t give it a 5 is, I rarely give that high # to anything with rare exceptions.

My GE microwave also has paint peeling off the top inside and bottom with rust as well. And cannot be repaired but not one person has said they were sorry or even owned up that it is a fault in paint. This is disgusting to think about this stuff falling into your food!!! This is not safe at all and 10% off new unit is not nearly enough considering they are up to $3000.00 now for microwave/oven unit.GE does not stand behind their products and it shows!!!!

I also bought a stove as well as the dishwasher. We Told them with great concern to put a extra warranty on the more expensive item, which was the dish washer... more could go wrong. We all agreed, including sales person. Day before the first year, the dish washer was not draining good. They said the warranty was running out. I told them, I had got extra yr warranty. The robot voice said it might be over. The repairman came in, and said the same thing. The repairman replaced everything in the dishwasher. It took him 3 visits. He got it working. He claimed there was an extra orange ball in the part and that why it didnt drain well.I started using it for 2 weeks and it stop draining completely. When I bought it the salesperson said, See I added the extra warranty on. But unbeknownst to me, she put it on the stove... How the heck am I supposed to know she did it wrong. I call the company and they said, Look at your receipt. And sure enough, it was on the stove. Looking at it and how the salesperson made it sound, it was understood by all that the warranty was on and I had an extra yr on the dishwasher... I looked at the receipt. Had a list of what I bought the warranty and we were good to go. Everything was replaced in it, everything. It was a mechanical issue and yet here it sits not working and I havent even paid for it. I am disabled and was give a lemon. I would never recommend a GE anything. This was a first... I usually buy Whirlpool and never ever had a problem... Theyre selling lemons and they know it.

My GE microwave works perfectly for microwaving and baking. It is also a convection oven and it works as well for baking as the microwave component does for microwaving. It is roomy and accommodating. Ive had the microwave for 10 years and have never had a problem with it.

I purchased the model (PEM31SM1SS) GE Profile (Spacesaver oven) in November of 2008. Less than a year later, it overheated and failed. Since it was still under warranty, the repair was managed by the appliance vendor. The scorch mark on the rear wall of the oven was and is still there. During the past year, the paint on the interior roof began to bubble and peel. There is now a broad area of exposed metal and the paint around the interior door frame is also peeling. When I returned to my vendor, I was informed that several other customers had the same issue and was told to call GE. I also checked online and found many other complaints for the same thing.When contacted, GE offered me a $75 rebate voucher, applicable only if I buy another GE microwave. The current price for this model - the only one anywhere that fits the space - is $279. Even with the voucher, this is still a lot to pay for a product that has proved to be defective. GE does not appear to stand behind its products. It used to be a reliable company but given the issues Ive had with both this microwave and my expensive dishwasher, I will be looking elsewhere in the future.

I have purchased a GE microwave/convection oven 7 months ago. A month ago, the control panel broke down and it would not turn on. I called up customer service and a technician was sent after a week. They have diagnosed it and the motherboard needed to be replaced. The said part was ordered and I was told it would be delivered in 2-3 days and a service will be scheduled in a week. A week came and no parts showed up. I have called up customer advocate and they assured me the said part will be delivered in time for the service appointment.Unfortunately, when they came, the said parts have not been delivered and I was given the lame excuse of systems failure; the request has not gone through their system. So the technician assured me that he will put in an overnight request for the said parts and the oven could be fixed within the week. He even gave me his work and cell number for me to call if I have any inquiries. But he never picks up or even returns my calls. So another service appointment was scheduled and parts were delivered, only to find out that it was the wrong parts, supposedly for another customer and for a different microwave model.Its really frustrating when people keep on reassuring that they are going to get it done, but has done nothing but lip service. Its been over a month and my microwave is still a broken microwave. I have learned my lesson and will never again in my life time purchase a GE appliance. PS: I should have listened to the Home Depot guy that sold me this microwave.

We have a GE Advantium Microwave. It is our second model (we moved and left the first one behind). It is spacious, has an intuitive menu system, cooks extremely well, also includes a convection oven feature that we use to great advantage. The nicest microwave weve ever used (and weve used plenty of them).

We bought a suite of Slate GE appliances during kitchen remodel 2 years ago. Weve had the dishwasher, model GDT580SMF2ES, motor replaced twice now and it is still loud and stops intermittently. Thank goodness we have the extended warranty! The over stove microwave is now starting to run when we just shut the door and stops intermittently. Were ready to replace everything with a reliable brand and cut our losses. We will never buy GE again.

From these posts, Ive seen people saying that they couldnt trust GE American-made anymore. Our microwave oven was made in Malaysia, but GEs home office appears to be in Louisville, Kentucky. Our problem: peeling paint on the door and upper part of our 2009 GE #JES1451DN1WW oven. As a cancer survivor of 8 years, my antenna goes up with any defaults such as this. On a common sense scale this should never be happening. I was very sad to see no recalls on these items Ive been reading about and am frankly scared to use this microwave. Shame on you, GE.

Purchased a GE over-the-range microwave worth about $400. About 2/1/2 yrs in it stopped working. Had a GE repairman come out to fix it. They charge $95 just to come out. I complained so they gave me 50% off parts and labor after the initial investment. It took him about ten minutes to pull out the defective part, a $10 thermostat which he replaced. Total cost: $162. Ive had GE products for years but the new ones are much more cheaply made IMHO. Made in Malaysia. In addition, the handle is breaking off as are plastic parts coming of the top of it. I guess Ill consider getting extended warranties from now on because these products are cheap. If Id had it longer, Id have bought a new one instead of fixing it.

JVM6175SFSS - I purchased this over the stove Micro in July 2014. When I cooked a potato or frozen meal it would sound like it was going to explode. Condensation drips down behind my stove and the window and door to it get all steamed up. The fan clears the door & window but is very loud and intrusive even on low. Besides that I have never needed to use a fan when I use the microwave. GE repair came and said there was nothing wrong with it. But after thinking about it, came back the next day and took it apart. The tech called GE engineers and described to their amazement the way the inside was made. They said no way. So the tech took pictures and emailed them to GE. They reviewed it and said thats the way it is. I wouldnt stand for that and called them again and told them that the bottom of the micro gets scalding hot. At that they changed it out.... for another one with the same problem. The wall behind the stove is getting ruined from vapor dripping and all the same problems exist. They will be coming again and I am going to insist they take back their junker and let me buy a safe microwave of another brand even though my other appliances match. I am sorry now that I bought my GE stove and refrigerator now because they match the micro.

We recently purchased three GE Profile stainless steel appliances for our new home. The total was somewhere around $3500. Within two weeks our $1000 dishwasher would not work. It took FOUR service calls and THREE weeks for it to finally be repaired. Now our $2000 oven (traditional/convection) has stopped working and the oven light will not go off without us tripping the breaker. Service tech not available for 5 days. I am expecting the new micro to go out any day now. All of these appliances are less than two months old. We had GE builder grade appliances in our previous home that are still running strong after 16 years. That is the reason we went with GE again. However, after the above mentioned issues with our new GE appliances, I encourage anybody who reads this to NEVER, EVER BUY ANY GE PRODUCTS AGAIN.

On 05/04/2014, our GE microwave over the stove unit burst into flames. My wife was sitting in our family room and heard the microwave fan start (spontaneously). Then she observed flames reflected in the kitchen window. When she went to the kitchen, she observed the interior of the microwave was aflame. The fire was extinguished with a spray bottle of water. The burning items appeared to be insulation. The fan from the microwave was with the burning insulation on the rotating plate.

I have had 2 of GE microwaves, above the range models. Both the same model, but different years. One stainless finish and one almond. They are almost exactly the same. They are efficient, and I like the carousel for even cooking. But I would like it if the light bulbs under unit were easier to replace.

GLDT696 series dishwasher - I have put up with my GE appliances and their problems for years, but now I will throw in the towel. Our Contractor appliances were replaced 5 years ago when remodeling the kitchen. Ten years of no problems with cheap stuff replaced with Stainless Steel GE ovens, fridge, microwave and dishwasher. I will only mention the dishwasher in this posting. Bottom line... Wish I went with another manufacturer. The washer has a gasket that loves to fall out of place creating leaks or floods. The pump has failed after the one year warranty. The control board has been replaced twice and today it looks like there will be a third one. That is if I am stupid enough to hold on to this piece of junk. If I buy another manufacturers steel front dishwasher it will not match the other appliances. At this point I dont care. Unlikely to ever buy a GE appliance again.

My less than a year old GE microwave stopped working last week. My AT&T phone service died so I had to make repair arrangements online. Guy was here this morning. My microwave’s main board is fried. It does not conform to Repair Guy’s published schematics. Repair Tech could not upload new data to it. Repair guy did order three new parts including a main board. GE told Repair Guy that mainboard delivery ETA UNKNOWN. After three hours here repair tech left and told me to call GE customer care. Believe it or not, two hours on telephone with GE. First you need to talk to a customer service rep that cannot help you. They then determine you need a Customer Advocate. Then they need to input data on your file for the Customer Advocate.Then they need to transfer you to that department. Then you have to get a case number assigned. Then you give someone all the serial numbers and model numbers again. Then the Customer Advocate (CA) takes the call. The CA does not speak English as you and I speak English. After the CA puts me on hold to verify the purchase, then the appointment, then the tech and then the order they actually speak to me. In my case, the mainboard part is not available on CA’s computer. The CA has to electronically contact the parts department to find out if the part is in this universe. If the part can be delivered to my Repair Guy in Jackson, GA within 14 BUSINESS days from the date of the inquiry I have to take the part and wait for repair.In the event the part cannot be delivered in 14 days CA will start a process to get me a new microwave. The parts department has up to 48 hours to respond to the CA. When asked what happens if no response occurs in 48 hours, I was told, That never happens. It is the Christmas Holiday and I anticipated guests. My husband is disabled and his meals are pre-made frozen so I will have to decompose them and heat them on the cooktop. GE could care less about those issues. So after waiting five days for repair I have no working microwave. Someone told me not to replace my GE with a GE, but I did not listen. It is December, holidays, no microwave is an aggravation that I thought paying for a GE product would alleviate. So, on January 2nd I might get an answer. Part possible or new appliance COULD be ordered and delivered by someone sometime.

It is very quiet and does an excellent job cleaning. I really like the new slate finish on the front panel. It has a stainless effect but does not show marks as well as SS and is very easy to clean. Great design, the top rack is adjustable and the use of internal space was well thought out. Very simple / uncluttered and I like the control mounted on the top door feature. Dont recall the model number. The washer was in the $650 price range which is sort of in the middle but has a SS tub. In my opinion the performance and features are no less than more expensive brands / models.

I love the GE. I bought a GE dual fuel range about 3 years ago when my 6 yr old Frigidaire stove caught fire. Always wanted to cook with gas but have electric oven and broiler. It's also easy to clean the cooktop unlike older gas stoves. Love the big fast boiler eye.

Wow, Donna from NJ, I could have written your dishwasher report! But since I didnt, I have never been so disappointed in an appliance purchase as my new GE dishwasher! Not only are some of the dishes & silverware coming out more dirty than they went in, it takes a ridiculously long time for a cycle. And if there are more than a couple of tablespoons of water on the door, it will pee out onto the floor when the door is closed! Not to mention that there is junk stuck to the floor just inside dishwasher, under the door, after the cycle has run! Yet the worst part is how dirty dishes are after even a Sani Wash cycle! Sometimes, the detergent lid is still closed. Sometimes its open, but the detergent is still there. Even then, dishes may be cleaner in appearance that time, than when the detergent is gone. A water glass, may have gritty stuff - not just detergent stuck and hiding down inside, or more obvious all over inside the glass. I have spent the past year experimenting with various things: detergents, amounts of detergents, arrangements of dishes, heat of water, pressure of water, rinsing dishes before cycle, etc. Glass and pottery normally fare better than plastics, but again the plastic may have started cleaner than they come out! The dealer has been out three times, finding nothing obvious the DW itself, nor anything I have done wrong. He has been told there is a kit that would fix the performance problem, but he cant purchase it, nor can his distributor. I have been told the length of cycle is because our government regulates the amount of water used. So my question is, then its okay to use more electricity?! Its totally embarrassing to serve someone a drink in a glass that is found not clean near the end of the drink! And I, too, have an old 12-years-dishwasher that still works! It was even a cheaper brand. I never had to think where pieces were arranged in that dishwasher. I just thought, in my newly built house, I should have new appliances!

We purchased the GE Cafe series appliances back in mid-2016 (dishwasher, dual oven gas range and microwave). Over that time period we have had at least 10 repair claims. The dishwasher front door and seal have been replaced three times, has ruined my wood floors and baseboards. The gas range has had multiple issues, including broken lights, broken fan, and a manufacturers defect in the lower oven igniter which took our reseller and third-party warranty company three weeks to repair. The microwave oven had a plastic cover just break off one day - wasnt touched before - it just cracked off!Fortunately we purchased the units through Home Depot and purchased their extended warranty program. Unfortunately the warranty company doesnt replace units and wont include claims during the manufacturers 1-year warranty period in their lemon law policy. Ive repeatedly tried getting touch with the manufacturer, but they appear to be staying high-and-dry away from consumer grievances.GE doesnt stand behind their products. I dont think their resellers give a rip either. My advice - stay away from GE. If youre in the market for something Id look at LG. I have a refrigerator, washer and dryer from LG and have had zero issues in nearly 10 years of service. I have no idea if their reliability covers dishwashers, but Id certainly take a look.

We bought a model PVM9215SK3SS microwave as part of an over-the-range microwave oven/extractor fan combo. Unlike every other microwave combo weve ever had in our frequent moves, this microwave cannot run the kitchen timer independently of the microwave. If you try to set the kitchen timer when the microwave is running, the cook-time changes and overcooks whats in the microwave. If you try to set the microwave to cook while the timer is timing a food cooking on the range, it simply refuses to work. The instructions are very hard to both find and then understand, having been written in China to cover many different models. Apparently I can ask my phone to turn it on. I sure cant manage that very often in person! The fan is too loud for comfortable use even at the lowest speed, which is a great disappointment. A former Profile model was very quiet at every speed, and much more efficient. Were saving up for something that works.

GE microwave model JES1344ES. This is a stainless steel with black accent 1.34 cubic foot microwave oven. It looks great. The micro is heavy for its size. The stainless steel is brushed and low luster finish. The door handle is chrome as is some of the other accent pieces. The push button panel is easy to read and has a large knob for making manual time adjustments. The light inside is very bright. There is a rotating platter in the oven compartment that is not knocked off of its guide rollers very easy. The push button panel is a glossy black material that is easy to attract fingerprints. The preset times that are programmed in the microwave is the only part of the product that could be an issue. For example the popcorn button when used has burnt all of the different brands of microwave popcorn that we have tried. It is set about 30 seconds too long. There is no way to adjust the preset time that I can figure out. We set the time with the large knob manually and the popcorn comes out just fine. The preset times for the Auto Defrost are also a bit off. They are not long enough. We also have a Subzero freezer set at minus 20 degrees Fahrenheit so that may be too cold for the defrost presets. Overall the microwave is great except for the preset times that Ive mentioned. We use it daily and have done so for five years. It still looks excellent inside and out.

We purchased our new GE Over-the-Range Microwave (model HVM1750DPWW, 1.7 cu. ft.) for $269.00 in February of 2012 and in August of 2013 it started to malfunction. Specifically the microwave would start on its own whenever we would OPEN the door. Now the microwave does not work at all (with the door closed or open). Based on the feedback that I have read in some of the posts on this site, I will replace the microwave since the maker can no longer be trusted to manufacture units that are robust and safe. But what manufacturer can be trusted at this point? It is my understanding that all microwaves (from all major companies) are currently made overseas with poor materials and highly suspect safety and quality standards. (Note - previous GE Microwave [same type - over the range] lasted for 14 years.) Thanks to Consumer Affairs for allowing us to post unfavorable reviews.

GE above stove microwave (DVM1850DM1BB) stopped working and went completely dead after 1 year. Purchased a second GE microwave because it easily fit into the existing space. Sure enough, the second microwave stopped working and went complete dead a little over a year. I have always heard bad things about GE products, now I can confirm those negative comments about GE products are true.

Our dishwasher has gotten very warm mid-cycle and now trips the breaker in the house each time we run the cycle. The problem became evident in April 2012. We have called in a GE repair person to fix it and they said it was a heating issue and not repairable. We have not used it since, but have not replaced it with a new one yet. In August, we read about the recall of a similar model number manufactured within same time frame. Our machine model is PDW7300J03WW, the recalled model is PDW7. Our machines serial # is **. Strangely, the serial number is not listed in the recall, even though symptoms are exactly the same!We have called GE Consumer Affairs at 1-800-386-1215 four times, the most recent today, 9/14/2012. Each time we call, we are left on hold for 59 minutes only to be disconnected automatically! I am sending a registered letter to GE CA with a copy of this link and intend to contact my local news if I do not receive sufficient response within the week. Does GE need to see an actual fire report from my fire department or worse in order to get their attention to replace the unit? It is disgraceful and extremely dangerous.

This is the second time that my GE microwave oven is peeling the paint on the inside of the oven. We paid over $240.00 the first time and think that this is a serious flaw this particular oven has. I think that the company should be liable, not the consumer.

Our microwave was manufactured in September 2010 and we purchased it in October 2010. It has been used a few times a week for reheating leftovers. I have owned secondhand microwaves and unknown brand microwaves, and they have been more reliable than the GE Profile. My husband and I invested in the Profile series when we remodeled our kitchen. After a lifetime of moving and living in homes with much to be desired kitchens, we decided to spend money to provide ourselves with a functional kitchen. If I had to do it all over again, I would have saved myself the trouble and purchased my appliances from another company.After having to call GE to send out a repair person 5 different times to work in our microwave oven, we are left with a nonworking microwave oven. It seems that a company that has made record profits from their faithful American fans could do the right thing and replace the microwave oven with something that works. Perhaps they do not have such a product. They have offered to let us buy a new one at a big discount, but they have not clarified what the percentage will be. The problem I have with this is that spending one more dollar on a product with no backing from the company it came from would be asking for more let down. I believe Ill have this lemon removed and quit before I take on any more consumer letdowns.

About two years ago I moved into my condo and as a housewarming gift my sister gave me money to buy a microwave oven. I bought a GE over the range microwave. Well it quit over two months ago - really disappointed. I bought the next one but now after reading all these similar experiences I am sorry I bought the same problem.

I purchased a GE microwave and had 3 different problem with it. They sent a service man out and he could not fix the problems. Now GE said they are closing the case even though they know I do not feel the problem has been fix. My other GE microwave, I really liked until it stopped working around 8 yrs old. This one is a piece of junk. It is an over the stove microwave so I cannot just take it back to the store. I would say GE has really gone downhill over the yrs. This will be the last GE product I ever buy.

GE microwave oven (jes1651sj02) started to spark like lightning, which can be seen through the inside vent grid/grill located on the right. Sparks are seen just behind the waveguide cover where the magnetron is located. It seems to be a common problem with GE microwave ovens from what I have researched. The microwave has now stopped working and just makes an odd noise like groan or urrrrr. It’s just over 2 years old. Its a piece of **. It should last 10 years or more, like my last 2 have. I gave away our Sanyo because it wouldnt fit the decor of our new kitchen - wished I never had.

Microwave oven 2008 - The food doesnt go around anymore. The glass insert does not turn. What can I do?

Unit is only 7 years old and not greatly used (only two adults who dont use it much)… Purchased as part of package including GE refrigerator, range and dishwasher (already got rid of refrigerator, as parts kept breaking and unit had other chronic problems). I turned the microwave on to make popcorn - it immediately made a terrible noise and filled with smoke with an electrical smell. Unplugged the unit and contacted GE Repair. When I described what happened, I was transferred immediately to their safety unit because of the nature of the problem. A GE technician arrived today and almost immediately diagnosed the problem: a metal component that directs the waves of the microwave generation tube had burned out, and by federal regulation, he claimed, cannot be repaired - the whole appliance must be trashed and replaced. Once again, I have experienced GEs poorly engineered products that appear to be designed to fail in a relatively short time. Can you spell planned obsolescence? (No photo provided, as there is no external visual damage).

I purchased a stainless steel GE dishwasher for $508.68 since I remodeled my kitchen October 2016, I contacted GE in March 2017 because the stainless steel on the dishwasher door started to have rust spots, they sent a technician to look at it, they told me that they cannot replace it because the aesthetic warranty is only good for 30 days. They authorized the technician to replace the door, however I have the same issue with the new door, and also the dishwasher stopped working. I contacted them again. The technician was able to fix the dishwasher, but as far as the stains on the door they told me thats an aesthetic issue. They cant do anything about it. I called the consumer relations department. I spoke with CIARA GE case # **. They offered me a small discount and I have to come up with $400.00 to buy a new dishwasher.I feel that a good business should always stand behind its products. The dishwasher obviously is defective, they sold me an appliance that supposed to be stainless steel but its something else, the right thing for GE to do is to exchange the defective product for the right one. I am very frustrated that in less than a year I have to spend over $900.00 for a dishwasher. I am great customer for GE, I remodeled my kitchen, I purchased a GE refrigerator, cooktop, oven, kitchen hood, microwave and dishwasher, I think I deserve better than a small discount for a defective product.

6/11/2014. My microwave of 5 years the GE Adora starting to act strange. It would start to hum and the panel light would light up. The humming would only stop if I opened the door. Sometimes it would stop on its own. But today the humming kept continuing and I thought it was harmless until I heard a loud pop in the microwave and smelled something burning. The microwave glass turntable had exploded from intense heat inside the microwave. It was bizarre. Immediately I ran over and unplugged the microwave hood. In all the years and houses I own, this is the most expensive microwave I have purchased and it has lasted me the least amount of time! Microwaves shouldnt start on their own and thankfully I was home when it did. Otherwise my house would have burned down.

We moved in to our home in 2006 and it had a GE Monogram Microwave built in. The microwave died and I purchased a similar GE Monogram microwave to match our kitchen in 2014. That microwave died exactly 17 months later. Fortunately, we had a home warranty program as we are selling our home. I figured that this saved me the effort to complain to GE about their product... Wrong. The Home Warranty program sent a repairman who said we can order a part. A few days later I received a call that they would replace the microwave. OK... I checked online as well as with a local retailer to see which model is the replacement model, and trim kit. Today (about 10 days after I first called for service) they delivered the new GE Monogram microwave and installed it. Fortunately, I asked to test it and we tried to boil a cup of water. The contents in the oven being cooked were not visible. Either the light was too dim or the shading on the door was too dark. I have never seen a Microwave where you could not view what is inside. I called GE Customer Service while the installers were there and they refused to allow me to keep it until a replacement was delivered. They had to deinstall it, re-install my old (non working unit) and take the new one back. I called GE with my homeowners claim info and they sent me back to the Homeowner Warranty company to start the claim all over. Ridiculous.Instead of a replacement they offered me a cash value which was 60% of what I paid the retailers. When I asked why that amount? They only provide the value based on what the Warranty company gets the products/services for (wholesale cost). Net: If I used the money to buy another product it would cost me out-of-pocket for replacement. I am hoping the new unit to be delivered in the next 3 days works better. Otherwise, GE has a significant design flaw that doesnt allow you to view what is cooking in the Microwave. If thats the case, why have a window at all? Fyi - My Panasonic Microwave in our basement is working fine.... and has for years.

I purchased the unit just over a year ago and it started beeping one night with error scroll speed and then key pad shorted. In the end to repair costs more than to replace, even though it is above stove mounted unit. Do not buy a GE Microwave. Especially model # JVM6172DF1WW.

Soon after getting our new Cafe Microwave CVM2072SM3SS the control panel died. I called GE and power cycling got it going again. This is an over the stove microwave, so we were also told by GE not to use the right front burner without the fan on boost. The problem persisted from time to time and steadily got worse over our 5 years of ownership. Reading the internet this was a common problem known to GE but they took no action to contact owners. The panel is now dead and my only option, having tried the fixes on Youtube, is to invest money starting at $108 for an inspection or buy a new Microwave. My entire experience with this product has been a big disappointment as I also own a GE Cafe range, fridge, and dishwasher.

Bought GE range microwave JVM3160DF3BB11/16 from Lowes. Tripped the breaker. Replaced the breaker with a new. Would immediately trip the breaker as soon as you pushed the start button. Last time it tripped the breaker oven went dead. Wont even light up. Junk. Do not buy made by Haier in China with the GE name on it.

Bought a new GE over the range microwave in April 2021 and it broke/stopped heating July. They replaced the magnetron in September and its broken again a month later. Same issue and parts are out 2-3 months.

We purchased the following from GE: GE Profile refrigerator, dishwasher, microwave, oven and cooktop in 2006 (six years ago). Last six weeks, the refrigerator, dishwasher and cooktop broke! We have insurance through Assurant on the products since it was recommended. We purchased the insurance for repairs and parts. Refrigerator - the motherboard (if you have other words for this) went out (4 weeks for a part). Now it is fixed. Dishwasher PDW8280NSS - This was the final answer from GE Consumer Affairs:I do apologize for this entire experience. I will be more than happy to contact you today between the time frame of 02:30-04:45 PM CST. Any additional questions you may have, you can contact me quickest by email. Again, I do apologize and I will contact you later today to discuss further options available to you. At this time, being the part is not available, the best option would be to offer a prorate on this dishwasher for you in order to have a functioning dishwasher in your home. I do appreciate your patience in handling this matter and will most certainly speak with you this afternoon. Thank you. Really, I have a case manager? The products must be really ** good if you need this as a department. Everyone should rethink buying GE products. Never again. I am campaigning against them! I cant get the part on a six-year-old high-end dishwasher. We live in the US, dont we? This should be a class action suit!

We bought a new GE microwave oven in 2007. It failed in 2018 after much, much use. We replaced it with a Whirlpool which failed in one week. Lowe’s let us return it and we bought another GE like our original and we are very happy with it.

I bought the matching GE Microwave and Range four years ago. After three years of usage, the plastic on the handle melted and peeled, making it very uncomfortable to open the door. It was caused by heat from the GE range below. It took months to replace and cost almost $150.

We bought a microwave oven (CVM1790SS2SS, ZA301193K) for our new house some 4.5 yers ago. The flimsy, but very shiny, metal cover on the door handle split and the resulting sharp, but hidden, edge cut my finger. We covered it up with scotch tape, and ordered a replacement for the handle. We paid GE $102 (other folk sell it for $76, as we later discovered). There were no useable installation instructions. Our extremely competent handyman could not figure out how to do it and called GE for help at 800 636-2005. He was rudely dismissed and was told to look for instructions on Youtube! He spent 2 hours to install the replacement part. The screws that came with it, were not quite right. Ill never buy another GE appliance in my life. The Item was ordered by Ellen ** (It was shipped on 1/17/2017).

Dont buy one. I bought two last year. The first one completely died before the 60 days were up. I took it back to Sams club and bought another. The tag inside says it was made February 2011, so its only a year and a half old. Under the carousel, the paint is peeling big time. I wrote GE repeatedly, asking if it was still ok to use it. After ignoring me for quite some time, I got this reply. In the notice, they told me to get Sams club to replace the defective and apparently unusable product they are selling knowing it is defective. I love the part where you cant cook something with too much liquid in it. Who does that when they microwave?Heres what they said: Thank you for contacting GE regarding your microwaves and the paint peeling issue. I did some research on it and found that it a common issue among all brands. Excessive heating of un-covered liquids can create a high amount of condensation that the inside paint is not meant to withstand. Minor chips to the coating on the microwaves interior cavity will not affect the products performance. However, if the coating is actively flaking or peeling anywhere inside the oven cavity (including under the turntable), discontinue the use of the microwave and replace it. GE does not have an approved method of repair, and the microwave is not repairable. Please return to Sams club for an exchange, if you are still within the one year warranty. If Sams is refusing to accept the return, contact the Sams Club Support Team at 1-877-885-2787. GE will then reimburse Sams club.

Sometime in the 1970s, my mother bought all new GE appliances; a refrigerator, a kitchen range-microwave combo and a dishwasher. After her death my husband and I moved into her house and continued to use these appliances until 2007. The refrigerator and dishwasher are still going strong as of now... October 2014. The refrigerator only needed the drainage line cleaned. The range began to have some electrical shortage problems and rather than try to repair (which is what we should have done with both appliances), we decided to replace the refrigerator and range/microwave. We bought new GE appliances; a GE refrigerator (my brother put the old one in his shop), GE microwave and GE range. The new refrigerators icemaker would not work property when we got it and the microwave (Model #JVM2070SK02) quit early this year (big difference in the old microwave at 30 some years use and my new one at only 7 years use). Because my husband was diagnosed with a brain tumor and I was the only caretaker, I was not able to address the malfunctioning icemaker immediately. In fact, because of my husbands hospitalization, I wasnt even at home during that year enough to use the icemaker. WOW! What a ripoff GE is selling to consumers. My complaints wont solve my problems nor the problems experienced by other people who bought these defective appliances but it helps to vent my anger. Just recently a small leak in the waste-water drain hose (easy to replace) sent me scurrying to find a new dishwasher but when considering the replacement of my 1970s dishwasher and the reliability of my newer appliances, I decided that my 1970s dishwasher will outlast anything I could replace it with. So I decided to replace the waste-water drain hose myself.What a sad appliance market we have in the US when buyers have to replace newly purchased appliances anywhere from a few days to a few short years after purchase. I think appliance companies intentionally produce inferior, unfixable products so consumers will replace their inferior ones with new inferior models thus keeping up sales. Do we have a choice? I lived before dishwashers and microwaves and I can live without either now. I would prefer not to go back to wood cook-stove and an icebox but I may not have a choice (I actually have an icebox if needed). Is there any way to hold companies responsible for the products they produce? If anyone out there has had longevity of 10 years or more use from a newer appliance line, that is appliances made since 2000... Please share the producers name with rest of us. GE isnt what it used to be and neither are many other US brand name appliances.

I purchased a GE dishwasher, stove and refrigerator in December 2012. All 3 appliances have broken, needed parts (which were also broken) and I still have appliances that arent working appropriately. The dishwasher door broke and it doesnt clean or dry well. The induction stove (the main burner) doesnt work and the replacement part was delivered to my house and that was delivered broken. The fan in the refrigerator broke and still remains broken. I have had nothing but headaches since the day the appliances were delivered. I would not recommend GE appliances.

I own a GE Model #JNM1731DM1CC that came with my condo, in March of 2008. After two weeks, the tray was spinning, and nothing was heating up. They came, and replaced something, and it worked again. It is now November of 2011, and the ** thing doesnt go off. When the timer stops, and you open the door, the table turns, and the microwave is on, letting rays come right out at you. I have to unplug it after every use, so that I dont expose myself to rays coming from the microwave. I spoke with several appliance repair shops, and they told me that it is probably the circuit board, and that to repair it would run at least $200. I am so disgusted with GE. I also have a stove that practically blew up, when the door shattered, after only having it for six months. They had to come and replace the whole glass front. I doubt very much, if they will help me, because it took at least 12 calls to get them to replace the glass door, with the glass all over the place, and inside the oven, four days before Easter dinner at my house.

First, as a new homeowner blessed with select builder-provided appliances, I never imagined I would be authoring this letter 4 months after closing on the new home. Your friggin’ microwave oven light mechanism truly sucks! I lost the two bulbs a week or so ago and purchased two more at the cost of approximately $10, even though a one-year warranty was stated. That was okay, as I was more interested in fixing the problem versus starting some long-range purchase interest. So, and this is the most aggravating aspect, I have the correct pins and life is ** good, and as I attempt to insert the first, the ** pin breaks off. Okay, so I reflect on the horrific engineering of the mechanism, and I softly” align the second of the two bulbs, and the ** pin breaks off again. ** is my predominant theme tonight. As well, believe me, I am going to inform Taylor-Morrison that their respective selection of your friggin’ lousy pieces of crap is corrupt and misguided. You suck, G.E.! I’m moving forward.

Not very satisfied with the functionality. Turntable does not work or has ever worked. Time features and power adjustments are not very intuitive. I would not recommend this brand, I believe there are other brands out there are much better for the same price range.

We have had this microwave GE JVM1631wb007 (2003) for a number of years installed above our stove. It was given to us by my husbands son so we did not have it registered with GE as owning it. However, I just sent an email to GE today asking for help as I find absolutely nothing on the internet about a scorched outside microwave door. We have had no issues with it whatsoever - until now. When we returned home from a one week vacation this past Sunday evening, we came home to a scorched OUTSIDE door on this microwave! The inside is fine. The two people who came into the house while we were gone said they did not use it but it is DEFINITELY scorched around the entire area on the outside around the screen area. I refuse to use it although my husband (who is an appliance repairman but does NOT work on microwaves) says its fine to use. Its not only hideous, it LOOKS unsafe to use. Im scared its going to catch on fire but my husband says dont worry and go ahead and use it! Im attaching a pic of it... Anyone else heard of this? Its not like we dont have the money to replace it. Im NOT going to touch the thing... You cant tell him anything. He thinks its fine. I need PROOF that this is dangerous to convince him... Please help before the house burns down!

My GE counter top microwave (JES1456), purchased from Home Depot less than a year ago, just stopped working today. No lights, or anything. The electrical outlet is fine. The GE warranty appears to be effectively meaningless. It is cheaper to replace the oven, than have it repaired. I will avoid GE products in the future.

However, the GE Monogram Microwave ($499 at Best Buy) broke down 17 months later, a few days before Thanksgiving 2015. GE claimed it was out-of-warranty, and I would have to pay $99 to have a technician look at it, and would charge for repairs. We are stuck with the GE Monogram Microwave as it is a built-in unit and our cabinet is built around it. So we went and got a new one from Best Buy. When the new one came and when we removed it from the box, it had a large dent in it - a very large one. It clearly indicates a shoddy QC job, as the unit should not have left the factory with such an obvious dent. We asked BEST BUY to replace it, but a new one is not going to come till after Christmas. So it was 2 strikes against GE Microwave ovens for me.We spoke to GE and they were not very sympathetic, and amazingly did not even apologize for the inconvenience caused!! They just stuck to their out-of-warranty mantra, which I understand. But then the occurrence of a second event with another GE Microwave, and the inconvenience of sending back a big dented one was also not acknowledged or perhaps even understood by their CS representative. So it is strike 3 against GE Appliances for me.I would never recommend GE microwaves and was totally disappointed with the Customer service of the GE Appliance division. I also have GE Cooktop and two GE wall ovens and shudder to think what will happen if they should break down. Just sharing a sad experience that holds some lessons for me and my family and friends. (Rethink buying GE Appliances.)

Bought at Lowes (GE Slate GDT655SMJES Dishwasher). Even bought the extended warranty. Leaked and buckled the floor while it was under GE warranty on December 12. Had to file with our homeowners insurance to get entire floor replaced, $1000 deductible, twice. They have been out 5 times and still not fixed. Now the new flooring is damaged from same leak. After nearly $5,000 of damages, not to mention the time we have spent you would think a new $700 dishwasher would be cheaper. We bought the refrigerator, double oven, convection stove and dishwasher, matching. At this point seriously considering buying a different brand of dishwasher even though it wont match the slate. Never will we buy GE again, they dont stand behind their product, disappointed in Lowes as well for passing the buck.

Purchased GE Profile dishwasher model PDT750SSF2SS, received three weeks ago. Within 17 days, door developed issue where it would not open fully. GE contacted, company not too responsive, miscue with technician, failure to reschedule, unknown when it will get fixed. Purchased as a complete set (dishwasher, range/oven, refrigerator, microwave). Does not say much about GE quality or service. Would not purchase again.

We purchased the entire line of slate/GE/Adora appliances from Home Depot 11 months ago. The fridge has required a service call for a VERY loud freezer. The microwave is fine. The stove/oven is fine. The dishwasher is a GIGANTIC piece of junk! 4 service calls and its still clunking, tapping, grinding and just extremely loud. VERY DISAPPOINTED!! We can only run it at night because of all the racket. The layout of the sections for dishes makes it totally useless inside. It doesnt clean. Soap residue is everywhere. My old DW was quieter and more efficient. *Insert sad face here.*

Installed 07/06/2015 While I was asleep on 12/09/18 the oven appeared to start microwaving an empty oven on its own. When I came down 5 hours later the microwave had no power. I opened door and turntable had melted and glass had exploded. The ring under it was burnt and melted in one location. Top of cabinet on right side was hot. Then the internal circuit breaker restored itself and started some recovery process making odd noises sounded like the magnetron was trying to run since the top was getting hotter, after a minute the internal circuit breaker shut it down again. I then unplugged it. It appeared the magnetron started heating on its own and turntable did not rotate. All of the heat was concentrated at 12:00 edge of glass turntable. It also burnt the metal floor under that spot.

Don’t know the exact model type but it’s a built-in unit as opposed to a counter top type unit. It’s installed on top of a GE oven. Have had no issues whatsoever since purchasing the house in 2008. Barely no maintenance required aside from the normal cleaning of the inside of it and even that is pretty easy.

I purchased a microwave in Oct 2010. It went blank and nothing works. I checked to see if its receiving power. The power is okay. I purchased the microwave, fridge and stove at the same time. I always had confidence in GE products. Microwave should have lasted longer than less than 2 years. I didnt purchase extended warranty because of GEs reputation. Very dissatisfied customer.

Our microwave, model number JVM1750DP1BB, was manufactured May 2011. On Monday, Dec. 30, I was heating a bagel when the small plastic hook holding the rack caught fire. The interior of the microwave burned, but I was able to put it out before it spread too far. I shudder to think what might have happened it I had been in another room. Im irritated because I keep reading that this is a common problem. Im irritated because MY HOUSE COULD HAVE BURNED DOWN. Im irritated because it seems like GE isnt doing a great job at making it right. Ive attached a photo below, showing where the plastic pin burned. I can say that Im shopping for a new over-the-range micro, and it wont come from GE.

Clean neat appearance over stove. Fast consistent heating. Easy heating options. Turntable on or off. Also, love the stove top light. Cost a bit more than I thought it would, but not much more than others.

Two years ago, after owning a GE JVM1490 microwave-convection oven (over the stove) for three years, the door handle broke.Let me clarify that I worked for GE first as an engineer, later as manager, for 20 years including 6 in Major Appliances. I am ashamed of what I am reading how GE is treating customers today.I am perfectly capable of replacing the handle myself if I am provided the complete and correct assembly drawings and/or instructions. GE refused to provide me anything when I requested them. The scant drawings and instructions I found online are insufficient. As a matter of fact, the design is so poor that removing the internal bezel, which you must do to reach the handle fasteners, forces you to break the mounting tabs, requiring replacement of this part plus the handle. This was confirmed by the parts store I visited.However, even after removing the bezel, neither I nor another ex-GE appliance engineer could figure out the access to the fasteners. I have glued the handle three times using epoxy and Cyanoacrylate (super glue), but it has broken off a fourth time. I will figure out a way of fixing it before I pay GE close to $100 for both the handle and bezel. And if I replace the appliance, you can be sure it will not be GE.GE should be ashamed of the poor design and deplorable customer service they are giving now. How things have changed!My suggestion is that all with this problem post name and phone number of GE customer service personnel they spoke with.

We bought a brand new GE kitchen. We put all GE in the new kitchen. The hood/microwave/convection oven broke in 9 months. We had service out, and they wanted the same amount we paid for it to repair it. My husband is an engineer and he got it to limp along. Then in September, it broke and cracked up. All the control panel cracked and broke. It does not work. We called GE. They said to get a replacement. We went to Sears and bought a similar unit as the original has been discontinued. We were assured of a credit towards the new one. A credit would not be issued. Gary ** has continually called my home but not my cell. He reached me today in school, a Special Ed behavioral unit, and started yelling at me over the phone. He said that I did not provide serial numbers. I have many times. He said there is no record of my complaint. I have called, emailed and written at least 3 times providing all information. We just want a credit for the original unit. We have provided sales slips, etc. Please help.

We bought Cafe series appliances less than 4 years ago including dishwasher, fridge, stove and microwave. These are not cheap appliances. We also bought a service contract with them. When our dishwasher broke a couple of weeks before Thanksgiving, we called service to have it looked at. After 3 trips and over a month later the dishwasher is still not fixed. Each time we tried to make an appointment we were always given a date 1 week out and a 4 hour time window, but each time the technicians showed up late and once even 3 hours late despite the 4 hour window. The fact that after so many visits and part replacement the dishwasher is still broken says a lot about the quality of the product and its maintainability. All customer representatives work like zombies. The problem with GE lies within the culture. Nobody cares. The service contract is a total waste money.

Microwave and convection oven together...perfect for heating food or baking. Very easy to operate. G.E.profile. Mounts over the stove with an exhaust fan and lights. Also has a rotating plate in it to heat evenly.

The looks are ok. It works great, not too noisy. Wouldn’t mind replacing it with a different color and apparel. It fit great over the oven and is a space saver. Cleans up well, not too hard to clean. Not sure of the exact price, but I remember it was very cost efficient

I have a built-in GE microwave. It is easy to use and best of all very easy to clean. It is brand new and stainless steel. Looks nice on the wall above the built-in GE oven. I can easily reach it. Some built-in microwaves are too high.