Touch pad on GE CAFE over the range microwave started failing within first 2-3 years. Now, 6 years later, it has completed failed. Repair part alone (not including service call) is almost $550.00. Pure junk...made in MALAYSIA!

We upgraded our appliance package when we bought our village builder home 8 years ago. All GE Monogram appliances have rusted and now need replaced. New liners needed in oven which was so rusted we couldnt get the screws out to replace the originals. Was told by GE customer service rust to be expected when cooking. It creates steam and food particles can cause scratching!!! Maybe it should be steam proof especially a microwave. Even the door on this is rusted! Why the shelf ends in a freezer are rusted not sure on that one! Will NEVER buy this brand again and shame on them my upgraded appliances dont even make it to 10 yrs. A disgrace. My mother just replaced her 20 yr old oven. What is wrong that nowadays things dont last 5 minutes? Shame on you GE not recognizing a definite flaw in your products.

Less than three years ago, I purchased a microwave oven wall unit to replace an existing unit. Due to the size of the built-in cabinet, I was limited in choices. The cost of the unit was $2400. A few months ago, the interior wall of the unit began rusting and the enamel is peeling. I contacted the customer service dept via e-mail on their site. I was asked to send pictures and then informed that I should stop using the unit immediately due to the danger of arcing. I was also told that because I did not purchase the extended warranty, the best that GE could offer me was a new unit for $800. I asked for names of warranty companies and was given one name and number but told there were others that also offered the same service. I called this company and they clearly told me that the peeling and chipping was a manufacturer’s defect and would not have been covered by an extended warranty had I purchased one from any company. Then I contacted the GE repair service center and spoke with them. The man who answered explained that this is a cosmetic problem and that there was no danger of the microwave arcing unless there was less food in the microwave than the size of the area that was chipping. I am very disappointed in the response of GE, the pressure placed on me to make a decision in 7 days or the offer would be withdrawn, and the fact that the service department and the consumer service (complaint) department gave me entirely different responses to the same information and problem. I will probably have my cabinet rebuilt to avoid having to replace this unit with another GE appliance. Who would pay $$1600 for the use of a microwave/oven unit for less than three years? Unfortunately, GE seems to be the only company that makes a unit that fits the existing cabinet in my kitchen. Disappointing to say the least.

I purchased a new GE over the oven microwave to replace a 10-year old Spacemaker unit. After three weeks of use with no issues, the unit overheated excessively during a normal use. The heat was so intense that the pegs that hold the racks melted causing a severe burn on my sons thumb. I unplugged the unit fearing further injuries and/or fire. Are GE products manufactured poorly or did I get a lemon? Who knows? Anyone else have a similar issue? I am still waiting for GE to respond.

I purchased a GE dishwasher 1.5 years ago and it has been nothing but a problem since day one! The door will not stay latched and the dishwasher is perfectly level. You might get 1 or 2 washes in before you have to work on it again. We bought a set of appliances from GE and the stove and refrigerator have worked well. However this dishwasher is junk and I based on my experience I would not recommend this product to anyone!

I just built a new home and opted for all GE Slate appliances. No problems so far with microwave, fridge, and stove but the dishwasher has never once been dry or cleaned all dishes. We have had it a little over a month! Today when I went to run it, there was mold growing! I had a KitchenAid for 9 years and never once did any of this happen. From reading other complaints, it looks like Ill be living with this for some time. I will never purchase GE again.

My GE microwave oven died after 4 years. And my GE washer died after 5 years. Never ever buy a GE appliance. The market agrees, because their quality issues might be the reason the company has not been able to sell their appliance division for several years now.

Our GE Microwave Oven/Convection Oven Combo (Model: PT970SRSS) is a little over 2 years old. The interior paint on the ceiling of the microwave oven is chipping and bare metal is exposed. In addition, the microwaves glass turntable frequently slips off its plastic tripod base. Circular scratch marks, which also expose the underlying metal are evident in the area which is located directly below the glass turntable. The circular scratches are a direct result of the glass turntable scraping against the paint. The GE repairman said chipped paint is not repairable and that paint should not ever chip in a microwave, let alone a relatively new microwave. After many calls back and forth to the GE Consumer Relations person, we were offered a new combo at a discounted rate of approximately $1,000. (We paid around $2,000 originally.) Im not satisfied with this offer. I strongly feel that consumers should NOT have to pay to replace a defective item. GE needs to pull these defective and dangerous products off the market! Take a lesson from GM!!!

The microwave is over the stove with a vent. It is about an 1100 w microwave. I just have to eat out a little bit more time here are the ones that are bigger. The price was right there and that I would’ve bought something else.

I replaced a GE JEM25 microwave when the Magnetron gave up with a PEM31DWW unit. Within 14 months the paint on the ceiling of the oven started flaking off. Contacted GE and they offered to sell me another oven for $166. After reading all the negative reviews on this site, I dont think I will ever buy another GE product.

I have bought 3 GE appliances in the past 2-5 years, a microwave, dishwasher and oven with cooktop. They are all white and the white paint is peeling off. The microwave is the worst with most of the paint gone from the metal around the window inside. I will never buy another GE appliance again. To have 3 different appliances with peeling paint signals a definite quality control problem in the company.

In January 2010, I bought a sensor cooking microwave oven (Model: JES1460DN1BB Serial #: MS900742B). I paid almost $500.00 for it. Now, in less than two years, the inside is already clipping off so it is dangerous to use. I returned it to the store and was told that the guarantee was good for only one year. So, I would have to pay to have it repaired. My last microwave (before GE) lasted well over 10 years. I always thought that GE was a good company; I guess not. I feel that it is their fault. I seldom use the microwave and I even clean it with a damp cloth. I do not think that I should have to pay for the repairs and I should be given some kind of a discount on a new one. I feel that GE is now in the business of making effective appliances. They should stand behind what they make.

I bough a GE microwave oven, model JVM1740SM1SS, less than 2 years ago. The keypad says that it is shorted out and needs service. It turns on randomly. I unplugged it and plugged it back in, and it will either say, service needed, keypad shorted out or press clock.GE has so many complaints about there microwaves, some that are very serious. They still claim that there are no problems with them. They have to know there are problems, but do not want to issue a recall and take a financial lose. Its only a matter of time, before something so serious happens that it will be a bigger financial lose than a recall.

I bought the matching GE Microwave and Range four years ago. After three years of usage, the plastic on the handle melted and peeled, making it very uncomfortable to open the door. It was caused by heat from the GE range below. It took months to replace and cost almost $150.

We purchased the entire line of slate/GE/Adora appliances from Home Depot 11 months ago. The fridge has required a service call for a VERY loud freezer. The microwave is fine. The stove/oven is fine. The dishwasher is a GIGANTIC piece of junk! 4 service calls and its still clunking, tapping, grinding and just extremely loud. VERY DISAPPOINTED!! We can only run it at night because of all the racket. The layout of the sections for dishes makes it totally useless inside. It doesnt clean. Soap residue is everywhere. My old DW was quieter and more efficient. *Insert sad face here.*

I purchased a GE microwave from Best Buy about a year ago. Every time I wipe it clean, white paint chips come off the inside. This cannot be safe for me or my children. I did contact the company and they were of no help at all. They said that because I heat up liquids in the microwave, this will happen. Duh! I would not recommend purchasing a GE product of any kind (oven, fridge, etc). Their customer service is awful and their products do not last.

Not even a year after purchase of new cafe series dishwasher, stainless lining rusting. Service called, GE tech agrees rusting of lining, GE warranty says not under warranty. Ive replaced screws that show signs of rust with aftermarket stainless screws. Cafe oven has had three front knobs just fall off - two were repaired under warranty and had to purchase extended warranty on third because it was more cost effective. Cafe Refrigerator had drain plate in back of unit completely rust away, tech knew what problem was before he stepped foot in my kitchen, he told us this was common. He caulked some sensor inside fridge box during service, I asked why, his response was its a design flaw and unit will operate better with this modification. Oh and redesign the ice dispenser, its tilted towards the back of the freezer and the ice is dispensed out the front.

I just wanted to make future purchasers aware of an issue I had with the oven light (GE over-the-range microwave model JVM1540DM5BB) underneath the microwave. It is much dimmer than my previous GE oven. I bought it from Lowes and after returning to the store to check a floor model, I discovered none of the models were plugged in so you cant check this out in the store. You only find out once the thing is installed. Lowes referred me to the manufacturer who then told me, after asking if my oven had 1 bulb or 2, the oven was working as designed. How they could definitively determine this over the phone was beyond me, but that was the extent of the assistance.

We bought a new house with GE microwave, oven and dishwasher. Our fridge doesnt give any water anymore and our touch screen microwave stopped responding to any touch. When I called customer service to come see, they want to charge $80 just to tell you whats the problem. GE has the worst appliances. I will not recommend it. I will go with Whirlpool brand.

Wow, Donna from NJ, I could have written your dishwasher report! But since I didnt, I have never been so disappointed in an appliance purchase as my new GE dishwasher! Not only are some of the dishes & silverware coming out more dirty than they went in, it takes a ridiculously long time for a cycle. And if there are more than a couple of tablespoons of water on the door, it will pee out onto the floor when the door is closed! Not to mention that there is junk stuck to the floor just inside dishwasher, under the door, after the cycle has run! Yet the worst part is how dirty dishes are after even a Sani Wash cycle! Sometimes, the detergent lid is still closed. Sometimes its open, but the detergent is still there. Even then, dishes may be cleaner in appearance that time, than when the detergent is gone. A water glass, may have gritty stuff - not just detergent stuck and hiding down inside, or more obvious all over inside the glass. I have spent the past year experimenting with various things: detergents, amounts of detergents, arrangements of dishes, heat of water, pressure of water, rinsing dishes before cycle, etc. Glass and pottery normally fare better than plastics, but again the plastic may have started cleaner than they come out! The dealer has been out three times, finding nothing obvious the DW itself, nor anything I have done wrong. He has been told there is a kit that would fix the performance problem, but he cant purchase it, nor can his distributor. I have been told the length of cycle is because our government regulates the amount of water used. So my question is, then its okay to use more electricity?! Its totally embarrassing to serve someone a drink in a glass that is found not clean near the end of the drink! And I, too, have an old 12-years-dishwasher that still works! It was even a cheaper brand. I never had to think where pieces were arranged in that dishwasher. I just thought, in my newly built house, I should have new appliances!

My 5 years old over the range GE Microwave Oven in my old house had a keypad malfunction. I replaced that oven with a different brand. This time, my 2 years old GE profile microwave in my new house has the same keypad shorted like other users posted. I was hesitating to buy this brand at the time. But the look and match with other appliances, plus the good deal from vendor, I gave it another try. I made a terrible mistake. No more GE appliances for me.

I like the look of the oven but it took 3 shots to get it right. I had some bad luck with 2 out of 3. It seems the first 2 were damaged. I know many people would have given up but I owned one before this one and the only reason I gave it up was remodeling. The oven worked fine after 5 years. I guess I gambled on past performance and it still paid off. But I am really not sure about the door sometimes because it is a big door and it can seem tinnee and cheap at times. The overall performance is good and the looks are what I was looking for.

The looks are ok. It works great, not too noisy. Wouldn’t mind replacing it with a different color and apparel. It fit great over the oven and is a space saver. Cleans up well, not too hard to clean. Not sure of the exact price, but I remember it was very cost efficient

I have a GE microwave oven. The paint inside the door is peeling off and has been for quite some time but I never got around to calling them. I recently decided to purchase a new microwave and use my old one downstairs. I called GE to ask them about this problem as I didnt want to have this same issue with my new microwave. GE told me they would do nothing to help me fix the problem and I need to stop using it because it is a safety hazard. I told them the microwave still worked fine and if I need to stop using it, does GE offer any compensation for something that is obviously a defect. I was told, no, GE will do nothing. I told them Id even be happy with some touch up paint but the lady was so rude, she would just sit there and not say anything until Id ask, Are you still there? Granted my microwave is several years old but because of this door defect, Im being told basically I use it anymore even though it still works. I need to just throw it away. I have a new GE microwave on order but thanks to their horrible customer service will be cancelling that order and buying another brand. I also will not ever purchase another GE product. I told them this and they said, fine. Obviously they dont give a crap about their customers.

We have an under the cabinet microwave oven. I like the size of it and it works well. It is white so it gets dirty from cooking on the stove. It has a light on it for 2 different lighting needs. It has a brighter one and one for night time also. The buttons are really easy to use. Not hard to program it at all.

We moved into a new home in June of 2011 with the appliances already included. Ours came equipped with a GE, over-the-range microwave, model JVM1540DP1WW, manufactured in Malaysia, in April of 2010. Within several months, the revolving platter began to make a bumping noise while turning and then it eventually quit turning altogether. Five service calls later, we had the platter motor replaced, circuit board and four fan motors (apparently the platter has voltage supplied from that fan to make it run) and it still didnt work.It was taken back to the shop and eventually the problem was traced to a loose wire on a terminal connector. After a month of operation, it is again beginning to make the bumping noise while the platter turns. To top it off, Consumer Reports (the March issue) deals with problematic microwaves, especially the GE model and the unexpected fires that can occur. In addition, they can be susceptible to (not always however and only on certain models) wireless transmissions which could potentially cause them to start on their own. I know for a fact that it knocks off my XM Satellite Radio when it is running. Bottom line...its history and will be replaced with a check rated appliance before I too have a major problem.

Purchased a GE over-the-range microwave worth about $400. About 2/1/2 yrs in it stopped working. Had a GE repairman come out to fix it. They charge $95 just to come out. I complained so they gave me 50% off parts and labor after the initial investment. It took him about ten minutes to pull out the defective part, a $10 thermostat which he replaced. Total cost: $162. Ive had GE products for years but the new ones are much more cheaply made IMHO. Made in Malaysia. In addition, the handle is breaking off as are plastic parts coming of the top of it. I guess Ill consider getting extended warranties from now on because these products are cheap. If Id had it longer, Id have bought a new one instead of fixing it.

After many searches trying to do due diligence, we bought a GE dishwasher online Nov 2014. It was delivered and installed two weeks later. The day (Saturday) after delivery we loaded it and started the cycle; water went in, the circulation pump started and then the machine stalled. The machine was reset pumped out, restarted but no further improvement.Called the GE service number and after a 20 minute wait was informed that a request would be placed to a local service company. Monday the local service company (30 miles away) called to inform us they had to reject the service request and that GE would set up another. Three days later GE was called again. They were unaware that the service request was rejected so had not attempted to find someone else. They could not get another company to respond and told us to arrange the service call ourselves, pay the bill and submit it to them.My wife and I are now wanting to return the machine but were informed we would have to go through the local Home Depot. They informed us that we would need to have GE arrange it. GE was called back and informed us that the dishwasher could not be returned as long as it could be repaired which leaves it to their discretion. The process to arrange these things took a long time, many delays and many phone calls back and forth to Home Depot and GE. The calls to GE often took 15 minutes to get someone who would forward the call to the service rep which placed back in another 15 minute queue. Do not believe that Home Depot will take returns. The advertising makes you believe they will take but they do not without GEs RGA which GE is reluctant to provide. Avoid GE. I am not the first to find out that GE warranty (one year) and service is poor and that they are more than willing to wait out the warranty to leave their customers with a possible lemon. Other dishwashers are available with 5 year warranties.

I have a new house (2 years old so out of warranty) and the kitchen has GE appliances that I choose. I hate, hate, hate them all! I have had problems from the first week in our home with the stove, microwave, refrigerator and dishwasher. I am so sorry I choose this brand! Today my dishwasher (for the 3rd time) isnt working. GE wanted to send their tech in a week. Then another week to get a part. I am so frustrated that I said forget it and called a local repair company. This is Friday, they will be here on Monday. I spent 2 hours on the dishwasher today. They had to replace my refrigerator and cooktop. My microwave went out 5 days after we moved in. Took 2 weeks to get it fixed. DO NOT BUY GE!

My GE over the range Microwave has broken about 4 times in a years time. My warranty company American Home Shield (AHS) has decided that instead of replacing this piece of garbage, its somehow worth it to keep on fixing it, which is apparently their MO for all their customers but I digress. After the latest breakdown (microwave lost power completely), I was referred by AHS to GE Appliance repair. Thus began the nightmare. The tech that showed up was incompetent at best. He showed up, looked at me, made a grouchy face and proceeded to walk in the kitchen with an attitude like he was doing us this massive favor. He opened the microwave door, closed it, opened his computer and ordered 10 (yes 10) different part. Again, he literally just opened and closed the door - did not disassemble to see what part was actually messed up. No diagnosis done of any kind. He scheduled to come out the week after that - didnt show up because I missed his phone call. Btw, I called him back pretty immediately and he didnt pick up. After being on hold for about 35 mins (which is clearly the GE standard hold time), they tell me the guy has left the area and they need to reschedule me for a week later. The day before the 2nd appointment, they called to reconfirm and then the morning of, I called, stayed on the standard 35-40 min hold and reconfirmed he was still coming and was told he was on his way. Well, the appointment time came and went and he failed to show up YET again so I called to ask wtf happened. They said he didnt come because I canceled the appointment thru an automated call. This time the idiot didnt call me like they always do. I asked for proof of this alleged automated call that was placed to me and they said no call record exist and so while it seemed like a system glitch, the tech already left the area and theyd need to reschedule it. I told them, No, thank you. Got a local repair company to come out the very next day. Turns out, out of the 10 parts that idiot tech had ordered, only 4 had arrived while the invoice still showed 10 being shipped. Let me clarify this: All these issues stem from GEs entire company: From manufacturing crappy products to HR hiring incompetent techs to customer service being absolutely nightmarish to supply chain not sending parts that are being ordered. And if you can somehow get their alleged consumer advocate department on the phone after a 40 min hold time, they dont give a crap either. All these employees MUST hate GE to drive customers away as far as possible. I own a business and I will never ever EVER buy GE again.

We purchased a black over the stove microwave from GE, the oven has great preset buttons and it extremely easy to use. It looks sleek and works great. The only issue we have had was a few months after purchase we tried to change the bulb for one of the lights and the entire mechanism crumbled and fell out so we only have one light now over the stove. Disappointing but everything else works great.

GE continually shows us why they are failing as a company. In just this last year I have replaced a less than 5 year old GE microwave, three separates parts to my GE monogram refrigerator, and now this one and a half year old dishwasher. The only appliance that GE makes that hasnt broken is the stove/oven that is over 10 years old and shows no signs of weakening.I purchased the upgraded stainless steel model that contained all the bells and whistles. It lasted 1 year and 3 months before the entire control panel stopped working. We utilized the dishwasher about once a week or once every two weeks in a two person household. Hardly a rough environment for a 700$ appliance. The repair costs was quoted for 99$ just to have GE look at it. The control panel was 140$, plus additional labor. This amounts to over 280$ to repair a year old product. I advise buying LG or Bosch.

I have an above the range GE microwave oven, model no. JVM1750M1CC. It has been in service for about 9 years. About 6 months ago it stopped working with an F3 code. The code claims the control panel needs to be replaced. I found that the price of the control panel was over $100 and the service call was at least $100. A little shopping around and I found I can purchase a new oven for about the same price. As the control panel is located just above the largest burner where water is usually heated to a boil, it receives a lot of steam. I visited a local church second hand store and purchased a countertop microwave and used it while I found a good solution. I decided to let it dry out for a few days and lo and behold it worked again. Unfortunately it only worked for a few hours, sometimes a full day and then I needed to let it dry out some more. I purchased an extension cord with an on/off switch and hooked it up. Now I can stop the electricity without having to climb up on a chair to pull the plug. Once I was set up with the easy on/off switch I could easily reset it. After about a week of resetting, it got the message. It has been working properly for over two weeks now with no failures.

For the amt. of money I paid for this microwave, you would think it would outlast the house. I bought it 3 yrs ago. The touchpad covering started to get warped right off the bat, and the handle was always steaming hot when you used the stove top (also GE). The other day, while using the stove top, I happened to look at the microwave, and it had no power. I checked the breaker, it was fine. I happened to notice a crack on the touch pad. After further investigation, I noticed the entire touchpad is shattered. It was clearly from the heat given off from the stove top. And I wasnt even using the microwave at the time. I sent GE an email, didnt even get an auto response. I am going to call them, but we all know what they are going to say, and I am not paying $482 for the part. Was hoping there was a recall, since so many people on the net complain about the touchpad.

Our Spacemaker microwave, which was installed over the stove August 2008, suddenly stopped heating food. My husband called GE, and their phone advisor advised us the microwave was under warranty. She said her computer screen showed our product registration, and she also saw we owned three other GE products. Fast forward, the GE repairman came and said the microwave repair cost would be around $400. The heating part wasnt under warranty nor was the labor. Mind you, the entire microwave (new) was under $400. We called the GE service center, and they refused to honor what their representative had told us. The most they offered was 50% off. I dont accept the premise that a new appliance should only last four years. I will replace my unusable microwave with a competitor’s brand and will pledge never to purchase a GE appliance again. I will also sell my GE stock, for I now understand why its going nowhere.

First, as a new homeowner blessed with select builder-provided appliances, I never imagined I would be authoring this letter 4 months after closing on the new home. Your friggin’ microwave oven light mechanism truly sucks! I lost the two bulbs a week or so ago and purchased two more at the cost of approximately $10, even though a one-year warranty was stated. That was okay, as I was more interested in fixing the problem versus starting some long-range purchase interest. So, and this is the most aggravating aspect, I have the correct pins and life is ** good, and as I attempt to insert the first, the ** pin breaks off. Okay, so I reflect on the horrific engineering of the mechanism, and I softly” align the second of the two bulbs, and the ** pin breaks off again. ** is my predominant theme tonight. As well, believe me, I am going to inform Taylor-Morrison that their respective selection of your friggin’ lousy pieces of crap is corrupt and misguided. You suck, G.E.! I’m moving forward.

We bought a top of the line GE microwave oven (model PEB7226DF1BB sn VA201160N) in 2014. It has now failed 5 times in 4 years - 2015, 2016, twice in 2017 & now 2018 - and the repairs have cost us more than the original price of this piece of junk. We bought it from a local dealer, KAM Appliances in Hyannis, MA, but had to resort to an independent repair service, because KAM was not very responsive. I know that I should have given up on it a long time ago, but in the past I always had good luck with GE appliances. Needless to say, I will never buy anything from GE again. I have learned that GE Appliances are now built by Haier, a Chinese company. No wonder they are junk.

I purchased a this GE Model CDT845P2NS1 on Oct 2, 2019 and the unit was received Oct 23, 2019. I installed the unit approx. 4 days after receipt and dishwasher functioned well until November 10th, 2020 when the unit failed to pump out the water. I contacted GE Service (MabeService) and was advised that the unit was not under warranty and as such I should contact a GE Canada authorized service centre.After several attempts to get someone to come to our location at Sharbot Lake we got hold of Capital Appliance Repair in Ottawa. They were not able to send a technician until November 18th. After diagnosing the problem the technician advised we needed a main control board and would have to order one and then come back to do the install of the control board. It is now February 21st 3 months after the visit and I’m being told that the part is backordered and they have no idea when it will become available. I’m extremely unhappy when you spend over $7,000.00 for a GE CAFÉ gas stove, Microwave, Refrigerator and dishwasher to find out you cannot get parts in a timely manner. As a customer of GE Canada I have had no help is solving my problem. It is not acceptable to have a 1 year old dishwasher that has failed, much less waiting for repair that has taken over 90 days to get repaired. DO NOT BUY!

We moved in to our home in 2006 and it had a GE Monogram Microwave built in. The microwave died and I purchased a similar GE Monogram microwave to match our kitchen in 2014. That microwave died exactly 17 months later. Fortunately, we had a home warranty program as we are selling our home. I figured that this saved me the effort to complain to GE about their product... Wrong. The Home Warranty program sent a repairman who said we can order a part. A few days later I received a call that they would replace the microwave. OK... I checked online as well as with a local retailer to see which model is the replacement model, and trim kit. Today (about 10 days after I first called for service) they delivered the new GE Monogram microwave and installed it. Fortunately, I asked to test it and we tried to boil a cup of water. The contents in the oven being cooked were not visible. Either the light was too dim or the shading on the door was too dark. I have never seen a Microwave where you could not view what is inside. I called GE Customer Service while the installers were there and they refused to allow me to keep it until a replacement was delivered. They had to deinstall it, re-install my old (non working unit) and take the new one back. I called GE with my homeowners claim info and they sent me back to the Homeowner Warranty company to start the claim all over. Ridiculous.Instead of a replacement they offered me a cash value which was 60% of what I paid the retailers. When I asked why that amount? They only provide the value based on what the Warranty company gets the products/services for (wholesale cost). Net: If I used the money to buy another product it would cost me out-of-pocket for replacement. I am hoping the new unit to be delivered in the next 3 days works better. Otherwise, GE has a significant design flaw that doesnt allow you to view what is cooking in the Microwave. If thats the case, why have a window at all? Fyi - My Panasonic Microwave in our basement is working fine.... and has for years.

We purchased the GE Cafe series appliances back in mid-2016 (dishwasher, dual oven gas range and microwave). Over that time period we have had at least 10 repair claims. The dishwasher front door and seal have been replaced three times, has ruined my wood floors and baseboards. The gas range has had multiple issues, including broken lights, broken fan, and a manufacturers defect in the lower oven igniter which took our reseller and third-party warranty company three weeks to repair. The microwave oven had a plastic cover just break off one day - wasnt touched before - it just cracked off!Fortunately we purchased the units through Home Depot and purchased their extended warranty program. Unfortunately the warranty company doesnt replace units and wont include claims during the manufacturers 1-year warranty period in their lemon law policy. Ive repeatedly tried getting touch with the manufacturer, but they appear to be staying high-and-dry away from consumer grievances.GE doesnt stand behind their products. I dont think their resellers give a rip either. My advice - stay away from GE. If youre in the market for something Id look at LG. I have a refrigerator, washer and dryer from LG and have had zero issues in nearly 10 years of service. I have no idea if their reliability covers dishwashers, but Id certainly take a look.

GE profile microwave convection - over the gas range. Oven temperature does not heat up more than the 370 degree, even if its set to maximum (450 degree). I purchased 4 ovens in the past year, all have the same defect.

I have just purchased a new GE dishwasher because mine just broke after 35 long years of excellent service. I am so completely satisfied with your GE products, and I would like to tell you also that the double oven stoves are still working well.

I had my original microwave for 20+ years. I replaced it in 2009 with a GE Model HVM1540DN188. Started beeping in middle of night a week ago, with message keyboard shorted service needed. I unplugged several times and it would start coming on by itself. I cannot believe they dont warranty their shoddy keyboards. I am very angry. I think they should stand by and replace their keyboards free of charge since they are fully aware they are making deficient product. This is scary to have an appliance just start beeping and say shorted... luckily I had my original wired in microwave replaced and put in a plug in or I would have flipped out if I could not unplug it. I got this along with the GE stove... so far the stove is not beeping...

Our Profile over-the-range microwave failed after 2 years. (Warranty was for one year!) One day it suddenly died. The repairman ($100) said repeated twisting of the wire from the oven to the door (which contains all the electronics) is inevitable with opening and closing. The wire often breaks within its insulation: a bad design fault. No question of replacing the wire; we would have to order a new door, for nearly $400 plus $200 for installation, which requires 2 service technicians. This is more than the cost of a new OTR microwave. He advised us to get one with the controls beside, not in the door. Unfortunately GE is the only company that makes a microwave in the same colour as our range.

I had to place a new order for a trim kit for my new microwave oven since the original one did not fit. I was told it would be 5 days when I placed the order, then it was backordered for 5 days, then 7 more days and now 3 more days. When will I receive the product that I have paid for 3 weeks ago?

JVM1540 - We replaced the microwave that came with our home above the stove. When we took the old one out, the blower was not installed properly for ventless. We thought that had to be the reason it just stopped working. We felt sure it wasnt GEs fault as we have always trusted them for a quality product worth the price. WRONG! I cant help but wonder if Lowes knows they are selling a costly piece of junk! When our new one quit working, we replaced the fuse 3 times, now it says keyboard is shorted service required. And thanks to this site I am tossing this piece of junk without spending any more money. GE shame on you!

Dont buy one. I bought two last year. The first one completely died before the 60 days were up. I took it back to Sams club and bought another. The tag inside says it was made February 2011, so its only a year and a half old. Under the carousel, the paint is peeling big time. I wrote GE repeatedly, asking if it was still ok to use it. After ignoring me for quite some time, I got this reply. In the notice, they told me to get Sams club to replace the defective and apparently unusable product they are selling knowing it is defective. I love the part where you cant cook something with too much liquid in it. Who does that when they microwave?Heres what they said: Thank you for contacting GE regarding your microwaves and the paint peeling issue. I did some research on it and found that it a common issue among all brands. Excessive heating of un-covered liquids can create a high amount of condensation that the inside paint is not meant to withstand. Minor chips to the coating on the microwaves interior cavity will not affect the products performance. However, if the coating is actively flaking or peeling anywhere inside the oven cavity (including under the turntable), discontinue the use of the microwave and replace it. GE does not have an approved method of repair, and the microwave is not repairable. Please return to Sams club for an exchange, if you are still within the one year warranty. If Sams is refusing to accept the return, contact the Sams Club Support Team at 1-877-885-2787. GE will then reimburse Sams club.

I purchased this Spacemaker Microwave Oven (HVM1540LP1CS) from Home Depot in Aug. 2010 along with a GE electric range (JB400SPSS). I wanted the appliances to match and they look very nice in our kitchen. Four days ago the microwave stopped working, that is, it comes on and appears to be working but does not heat the food placed in it. After looking on the internet, I found that other consumers have had the same problem and it appears the megatron is the culprit. The microwave was manufactured in March 2010 in Malaysia so it was not an older model that has been sitting in a warehouse somewhere.The cost to repair the microwave will be about $125 which is about half of what I paid for it. I will not repair this microwave just to have it fail in 20 months, General Electric should be ashamed of themselves for selling foreign-made products that do not last more than 2 years. My only hope is that the electric range we purchased does not follow the same course as the microwave, consumers should be aware of these problems before they purchase General Electric products.

My microwave is only 5 years old. It is burned out electronically. I would never buy another GE product. My GE Profile stove needs a $300 repair after 4 years.

I brought our brand new home just over 1 year and 8 months ago with all new GE appliances. One of the GE Smart Built-In Double Wall Ovens, the bottom one which we never use, but the inner glass shattered randomly, very dangerous and they want us to pay them $100 for the inspector visit and then more for the par and service $325 for the replacement, the GE is disagreeing they had a defect on installations. That is an experience that we never repurchase GE brands, my friend had the same issue. They replaced in their house this way without warranty, however they disagreeing our oven had the defect on installation, lesson learned, never never buy the GE again!

We have had our GE Advantium for 4+ years and the paint has started to peel off the inside of the door. We have an extended warranty with Home Depot but they deem this a cosmetic issue which is not covered. The cost to replace the door (part only) is about $260. Not sure self-painting is safe. I read here that we are not alone in GE microwave paint peeling off inside their microwaves, in general. Has there been any recall or calls action against them for this shoddy product? We love having this microwave/oven but feel like we got hosed by GE and Home Depot.

We bought a GE Profile micro/convection oven in December 2010 (model # PEB1590SM). It was working great until 11-19-2012, when the panel on the right side started to glow bright orange, then burst into flame. I thought my wife was goofy, so I tried to heat a cup of water. It was the same thing; the panel glowed bright orange and then flamed. We waited a week for a GE tech to visit. He said the wave guide is burnt. Its non-repairable so were waiting for disposition from GE service. There wont be another GE micro in this house. P.S. - Were still waiting for the GE case manager to call back after leaving three messages.

Needing some type of warning to indicate a clog or break down. Cycle: Pots & pans; heavy wash; normal wash; light wash; hot start; high temp. wash; heated dry; energy saver; cycle on: plate warmer; start delay (hrs) off, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1; Hot start plate; Pots & pans start; heavy/normal; high wash; heated dry off-rinse only. The color fits my kitchen arrangement. Needs to have a better warranty coverage. Needs a longer warranty on the basic coverage. Do away with extended coverage. Offer all parts and full labor for a longer time.

JVM6175SFSS - I purchased this over the stove Micro in July 2014. When I cooked a potato or frozen meal it would sound like it was going to explode. Condensation drips down behind my stove and the window and door to it get all steamed up. The fan clears the door & window but is very loud and intrusive even on low. Besides that I have never needed to use a fan when I use the microwave. GE repair came and said there was nothing wrong with it. But after thinking about it, came back the next day and took it apart. The tech called GE engineers and described to their amazement the way the inside was made. They said no way. So the tech took pictures and emailed them to GE. They reviewed it and said thats the way it is. I wouldnt stand for that and called them again and told them that the bottom of the micro gets scalding hot. At that they changed it out.... for another one with the same problem. The wall behind the stove is getting ruined from vapor dripping and all the same problems exist. They will be coming again and I am going to insist they take back their junker and let me buy a safe microwave of another brand even though my other appliances match. I am sorry now that I bought my GE stove and refrigerator now because they match the micro.

First of all we loved our GE microwave / convection oven for several years. We used both cooking methods with much satisfaction. Two months ago, the microwave started turning ON when we opened the door of the unit. I know this much be dangerous? Also, when using the convection oven, the microwave also operates, and ruins whatever I am baking. HELP!

This is the second time that my GE microwave oven is peeling the paint on the inside of the oven. We paid over $240.00 the first time and think that this is a serious flaw this particular oven has. I think that the company should be liable, not the consumer.

GE Cafe Series dishwasher model # CDW9380N20SS is a fire hazard. Three days ago, our GE Cafe Series dishwasher nearly caused a fire. If I had not been home that day, it surely would have. I ran the dishwasher as usual and went about my day several hours later. I detected a strange acrid smell and with my five-year-old who was ill and at home that day, discovered the dishwasher door was burning hot to the touch. I needed a potholder to open the door. Once opened, there was a blast of heat and smoke. I needed to use oven mitts to protect my hands from the heat to pull the racks out and handle the dishes. The heating element did not deactivate at the end of the cycle.If I had not been at home, the house would have been destroyed as all the plastic items on the top rack in the dishwasher melted. In addition the plastic parts of the lower rack, the wheels and their clips; the silverware holder; covers; the clips that hold the pot tins in place were destroyed, to the point that the majority of our silverware was coated with plastic. The plastic on the lower water dispenser has been demolished; it completely melted more than 50% of the plastic covering on the arm and is charred and burned. We are so lucky to still have a home!The door must be kept open. When the door is closed, the element super heats and presents a major fire hazard. We have noticed that there is a recall for similar models with plastic tubs, but ours has a stainless tub. GE needs to broaden the recall to include all these models. This is a serious issue that needs to be addressed immediately. Our GE Cafe Series dishwasher model #CDW9380N20SS was installed on October 1, 2008. I would not be surprised to find that parts from the recall in April 2008 were also used in the Cafe Series. I have discovered in the few days since the DW units malfunction that there are over 1000 complaints listed with similar, even identical complaints, on multiple internet sites with the same problems.

The side panel of our built-in GE Profile microwave 1999 caught on fire when my daughter was using it. It had a faint glow behind the metal plate. Then, it became flames quite quickly. A flash and pop was the ultimate end before we turned it off during the test. It had been working fine until the fire. This is a definite safety issue. Now that I know the microwaves have been faulty, it makes me concerned about the GE Profile electric stovetop burner. I have noticed it gets extremely hot and doesnt seem to want to turn off!

GE 1.6 cu ft over the range microwave. It performs well and has multiple options preprogrammed on keypad. The only challenge was installing and change over to an outside back exhaust (horizontal) to a vertical in wall duct.

I own a GE Model #JNM1731DM1CC that came with my condo, in March of 2008. After two weeks, the tray was spinning, and nothing was heating up. They came, and replaced something, and it worked again. It is now November of 2011, and the ** thing doesnt go off. When the timer stops, and you open the door, the table turns, and the microwave is on, letting rays come right out at you. I have to unplug it after every use, so that I dont expose myself to rays coming from the microwave. I spoke with several appliance repair shops, and they told me that it is probably the circuit board, and that to repair it would run at least $200. I am so disgusted with GE. I also have a stove that practically blew up, when the door shattered, after only having it for six months. They had to come and replace the whole glass front. I doubt very much, if they will help me, because it took at least 12 calls to get them to replace the glass door, with the glass all over the place, and inside the oven, four days before Easter dinner at my house.

Our GE Spacemaker XL microwave stopped working on 7/11/12. We purchased our house in January 2000 with the microwave included and have not had any problems with our microwave, until yesterday, when we woke up and tried to pop the kids breakfast in for a quick heat and it made a strange humming noise and you could smell plastic melting. All power was quickly turned off to the unit. Now to find a replacement for this built-in microwave is going to be a problem. The local technician stated the blower motor we need is no longer available. Thanks, GE, for at least 12 years of excellence. We are now looking for a similar replacement.

I have a GE over the range microwave oven purchased in 2011. 4 years old, hardly out of its service life. In 2013, while heating up my lunch, I heard a loud buzzing and popping noise. The plastic hooks that hold up a metal tray (yes, the unit comes with a metal tray) in the microwave oven caught fire. I called GE and demanded they repair the unit, they said they were not responsible since it was out of the warranty period. Having experience in the insurance industry, I reminded them about product liability, if this is a common occurrence, there would be potential liability issues for GE. The service tech said they would send someone out free of charge to repair the unit. He replaced the two hooks that fried and said they were no longer responsible for unit. Today, 01/28/15, we just had it happen again. One more hook caught fire. Hey GE, do you really think I will buy any kind of appliance from you again when you make a defective product and dont stand behind it? I will not. I would recommend people do your research carefully when buying a microwave oven, especially one from GE. I would recommend anyone do research when buying any kind of GE product since, in my opinion, they clearly do not care about their customers.

No issues yet. But only had for 6 months so time will tell. Read a lot of negative reviews but none here. Bought in Nov ‘18 from Home Depot. Delivered and installed on time. Replaced 13 yr old GE appliances that were still working.

I had a GE microwave that matched the GE range that was already in my condo when I moved in. When the range died, I got a new, matching microwave too. I like the way it works, the controls are intuitive and its easy to clean. No complaints.

I purchased a GE Profile stocks in 2007 and a GE microwave model JVM7195SK1SS purchased 12/30/16. We have replaced the knobs on the stove 2 times because of peeling in the past. Now we need to replace the microwave handle. The handles and knobs look like metal but they are cheaply made white plastic covered with a sharp silver coating that peels. It appears the knobs get overheated when the oven opens and the microwave handle from the steam when cooking on the stove. Last night I cut my hand on the handle! We reordered the faulty handle and now getting charge $100 from GE. The company should take responsibility for their poor design and replace it for free with a nonpeeling part. I know that we will get the same handle and won’t be able to use the burner below or hope that using the fan will keep it from cracking again. I would never recommend a GE product again.

We moved into our new manufactured home in May of 2013. That is the month our above range built-in GE microwave was installed. In October of 2013, one of my sons heated a frozen chicken cordon bleu serving for 3 minutes, 45 seconds, according to packaging directions. He said that some of the inside of his food was cool, so my other son put in his serving for four minutes, zero seconds. All of the packaging was removed and each serving was placed on a separate Corelle plate and covered with Glad microwave-safe plastic wrap. While heating the second serving, the microwave started on fire. Fortunately, my son extinguished the fire before it spread. The food did not combust. The fire seems to have started from the ceiling behind the fan. The entire inside of our microwave is clean except for the soot that billowed out from the center of the ceiling. When the service tech came, he scrubbed the soot off of the ceiling with some paper napkins (which he left inside of the unit) and said that the microwave was a total loss. He also said the fire was caused by misuse, because plastic wrap is not meant to be used in the microwave, therefore even though the fire happened within a year of purchase and installation, our warranty was void. I asked GE to get a second opinion and they agreed to send a third party servicer (A&E) who stood me up three times! I finally got to schedule a GE tech to come at the end of December and they sent the same guy who said the fire was our fault! He told me that he never said plastic wrap is not meant for the microwave, but that we are being dishonest because fires only start when the food is left in the microwave for too long. He accidentally let it slip that he is seeing the same problem with GE microwaves in a lot of new construction for student housing in Tallahassee. (We live 20 minutes south of there.) He attempted to recover GEs reputation afterward by saying that of course it was the students faults, too, for misusing the microwave units. Anyway, GE has graciously offered to sell us a new microwave at slight discount. Haha, no thank you!

Bought GE range microwave JVM3160DF3BB11/16 from Lowes. Tripped the breaker. Replaced the breaker with a new. Would immediately trip the breaker as soon as you pushed the start button. Last time it tripped the breaker oven went dead. Wont even light up. Junk. Do not buy made by Haier in China with the GE name on it.

I recently purchased a GE Profile 1.9 microwave oven from Home Depot less than a year ago. Last week I went to remove something that I had cooked and went to close the door and it would not stay shut. I ended up getting some masking tape to try and tape it shut in order to keep the light from staying on and burning out until morning when I could get a better look at it, thinking that it had to be something small that could be taken care of without any problem. Hinge adjustment, something getting in the way that I couldnt see, etc, etc. Wrong! I have been over this door with a fine tooth comb and there is nothing that I can see that is preventing it from staying closed, not only that but according to everything that I have read, I am very lucky that I didnt get fried while trying to figure out if the latching mechanism was functioning correctly. I am not even going to go through the long drawn out process of dealing with GE over this due to the simple fact that I have been there done that with my dishwasher that showed up with the front panel dented a few years back from the factory and I ended up blaming the place that I had purchased it through instead of GE and have since found out by reading other complaints that this seems to be something that is not unusual when it comes to GE appliances. I spent over 1100.00 dollars on the dishwasher and they only replaced the panel instead of giving me a new one, and I have never been satisfied with the way that it operates, and it was a very long and drawn out process and I am just not willing to spend the time again on another one of their products. It is unfortunate that we have entered a time where customer satisfaction means nothing, and the days of caring about having repeat business from a satisfied customer are over. The prices continue to rise on the things that we have become to depend on and cant seem to live without, but the quality and workmanship have not only diminished but also present safety threats. I will never purchase another GE anything and I am looking forward to the day when we all have finally had enough of this and do something that makes these companies stand behind the products that they sell and quits ripping the consumer off. Its rampant across the board no matter what you buy, and there should be laws in place in order to keep it from happening. We have laws for everything else, why not have a couple that protect the consumer and their pocket books.

I have many other things to do other than to voice my extreme and total displeasure with your company. GE - Huge Company, Small Customer Service. We purchased a GE microwave oven from ABT electronics in about August, 2013. In October, 2014 we had issues with the fan remaining on while the door was closed. Called GE. They said the unit was out of warranty by about 2 months. We felt that was a short period of time and that we called as soon as the issue became chronic.Had three service calls where the techs tried to fix a simple problem. First tech walked through our living room with dirty boots. Didnt fix the problem. Messed up our carpet. Bad attitude. Second call, two techs couldnt fix the problem. Said it was a door issue and they made some superficial adjustments. Problem not fixed. Third call, two more techs. Same result. In the meantime I tried to convince GE that I didnt want another service call. I wanted a new unit. No luck. I was offered a discount to purchase a new unit for around $300 or so. Im sure they spent more money on service calls than a new unit would have cost in terms of dollars and the reputation of one of the worlds biggest companies.Now, the fan for the unit stays on almost all the time after the cooking is done. Is this the best GE can do? If so, thats pretty sad. Tried to reach someone in sales who would get it. No such luck. DONT BUY GE AND IF YOU HAVE ISSUES DONT RELY ON A FACELESS, CLUELESS CUSTOMER SERVICE DEPARTMENT TO HELP IN ANY MEANINGFUL WAY.

We bought a new GE microwave oven in 2007. It failed in 2018 after much, much use. We replaced it with a Whirlpool which failed in one week. Lowe’s let us return it and we bought another GE like our original and we are very happy with it.

I bought the GE microwave from a GE dealer. We were very impressed that it is also a convection oven. It bakes, microwaves and even toasts bread. The oven had not disappointed us any way. I would recommend it to anyone in the market for a microwave.

My 11-month-old GE Advantium oven no longer has any display, totally blank. When calling to make an appointment I was unable to speak to a live person but scheduled one for today from 1-5 pm. At 5 pm I received an automated call that the technician was running behind and would arrive in about an hour. By 8:30 pm no one called or came to repair my oven. At 4 pm when I was wondering if I would see a repairman I attempted to find on the internet a phone number that would connect me to a live person but had no luck. I have no idea what company is being sent out to make the repairs so that I can get in touch with them. Their service sucks.

We just had a Fire in our GE Microwave, Model # JVM1750SP1SS. Manufactured in August 2010. Purchased at Home Depot in December 2010 and installed January 2011. The right rear shelf hook caught fire while the microwave was in use. Luckily, we saw it in time... We are not sure who to complain to or tell about this. We went on GE.com to inform them of this issue and am waiting for a response. I see here that I am not alone. There is other info being shared on YouTube about this issue as well. GE better make good on this for me. Now I have to find my paperwork... Figure out who will remove this under cabinet installed oven and replace it. I am probably on my own here as it is 3 years old!!

Microwave oven, model # WES1450DN1BB, manufacture date, April 2011 - Your customer service sucks! I called there 5 times today and was told my microwave oven has been recalled, yet no one knows! You dont have it listed on the recall or anything. Your Customer Advocate doesnt know its recalled but your Service Department knows and I was told by them that it says, Do not repair, return to the place of purchase. Yet, I called my place of purchase and they know nothing of it either, but are going to work with me the best they can! It was manufactured in April of 2011 and we bought it around July 2011 (we think it was around then). There are many complaints online about the same issues as we are having - paint all bubbled and peeled off the inside top, and smell of burning wires coming from under it! If something would have happened to someone in my family or to my home, you bet your ** I would have sued the pants off of your company! Someone needs to get their ** straight with what is going on in your company or you are going to have a lot of issues! I may bring it to a higher level just because I am so pissed off that no one was informed about this issue, and something very bad could have or still can happen to someone because they are not getting the information they need! Stop and think about it. Because of your companys lack of communication, someone could die! I am very pissed off!

I purchased a GE microwave, model LVM1750DPWW, in 2012. It was delivered approximately 12/6/2012 and was installed in July 2013 after our kitchen remodel was complete. In March 2014, my daughter was warming something on the rack when the back upper rear hook started sparking and caught fire. I am thankful the only damage was to the microwave and to the smell in the house for a few days. When I called Lowes and GE, they act like theyve never heard of this issue. Yet, I see many other complaints of the hooks catching fire. Just to be sure, I turned on the microwave again. The hook started sparking immediately. GE sent a repairman to the house who told me that GE ought to let people know not to leave the racks in the oven. Since she was cooking on the rack, it would be difficult not to have the rack in the oven. He said the oven was a safety concern, could not be repaired and that GE would bring out a new microwave and install it for me. Great! I was pleased - yet concerned. A couple days later, I received an email from GE customer service saying that we had put the rack in the oven incorrectly. There is NO way to have put it in incorrectly. Besides that, he couldnt have seen if this was true since the hook was burnt and melted. I am pretty angry.

I purchased the unit just over a year ago and it started beeping one night with error scroll speed and then key pad shorted. In the end to repair costs more than to replace, even though it is above stove mounted unit. Do not buy a GE Microwave. Especially model # JVM6172DF1WW.

We bought 3 GE Profile appliances in 2005 when we renovated our kitchen. We have not had much problem with the gas oven/range/stove. We have, however, had nothing but problems with the microwave (which I submitted a separate review for) and the dishwasher. Recently, a friend made some suggestions regarding the dishwasher. I then went online and watched some tutorials on troubleshooting my dishwasher problems. I tried all the new suggestions and the dishwasher worked OK the one or two times after that and then back to all the old problems: 1. We have to scour every dish until its nearly clean before loading (even though the instructions specifically stated no pre-rinsing necessary). 2. I am not sure the soap cup opens. The soap is always left caked in the cup resulting in running the dishwasher twice. We have tried all kinds of various soaps and they all do the same thing. The eco-friendly soaps are the worst. We strive to be eco-friendly, but how can we be if we are using the harshest soaps possible AND running our dishwasher twice?! Not to mention the pre-rinse scour and running water until it is 120 degrees prior to running.3. The dishwasher also leaks and is very noisy.I have read some other reviews on this product and realize our dishes are not always dry at the end. This is a non-issue for me. I dont care so much if the dishes are dry. I do prefer for them to be clean. Dishes are a task I do not prefer to do. It would be nice to have a functioning helper. I am grateful the thing hasnt caught on fire. I saw that this dishwasher currently sells for $800-$1,500. I cannot believe it. I wouldnt spend $100 on this piece of junk.

I purchased a GE microwave from PC Richard and Son in 2011. The microwave is mounted above the oven. On March 13, 2013, the microwave (model JVM1750DP1WW) sparked a fire inside while my daughter cooked a waffle. After I contacted GE via email, the case manager (Misty) sent a technician to my home to inspect the microwave. This was free of charge. The technician claimed the microwave was able to be repaired and he needed to order touch up paint and a few parts. I was shocked that the tech claimed this was a simple repair and able to be fixed. I said, You need touch up paint? This is going to look horrible. How safe can this be after having a fire inside? He claimed it will look good and I would not notice the paint. I spent $411.00 on this microwave less than 2 years ago. I dont think I should have it fixed and touched up with paint to cover burn marks. The microwave went on fire. I dont want it fixed. Its not safe and should be scraped for safety regulations, not repaired and touched up inside with paint. The tech ordered a few parts and I immediately called the case manager Misty to stress to her my numerous concerns on the actions of the technician. I made clear that I was not satisfied with my microwave being fixed and painted when it went on fire, but would like a replacement. I told her I could understand fixing it if it was a broken part or electronic device, but not a fire. She agreed that she also would not like to have a fixed microwave in her home, but that GE can sell me one at a lower price of $150.00. Really, do they need the money that bad that they cant stand behind a dissatisfied consumer when their product went on fire? This could have been so much worse. Lucky my daughter was in the next room. She smelled, heard the fire and stopped the microwave. I paid the $150 just so I can have a working, new, safer microwave in my kitchen. But this is crazy and not good business ethic on GEs behalf. This should be set as a recall, not a repair. I contacted the service manager again stressing my complaint and feelings about paying this fee for a new microwave. She said again that if the technician says the microwave can be fixed, then theyll listen to the technician and fix the item. Well this seems a little one sided since the technician works for GE. No brainier. What do you think he is going to say?

Over-the-range microwave failure (model JVM2052, manufactured Dec. 2010) was purchased and installed professionally in March 2011. Total cost is $546. First, the fan failed in about June 2012 and I thought I can live with this. In Sept. 2012, the unit failed, but the interior light and clock still work. I paid $97.00 for a service call from the dealer, and the tech said the power source failed(?). Estimated parts and labor for repair is $370. So, I will buy a new unit (not GE) and pay about $150 for delivery and installation and take away this GE unit. I live in Morris County, NJ and this is not a rural area! GE service rep whom I called said GE doesnt service this area and to look in the yellow pages for an authorized dealer. I called again and got the name and address of the president of GE Appliances, and I am going to write about this product.

I was very impressed by the look of the GE over-the-range microwave oven but my impressed state faded not too long after I began using the oven. My typical usage ranges from heating something for 20 seconds to soups for three to four minutes. Within the first month of purchase, the paint on the floor of the oven was peeling off, exposing the metal color. I was only wiping/drying out the oven with a soft cloth, never using an abrasive product or cloth, so the peeling paint was only due to moisture. I have now owned the oven for just over 14 months and not only is the floor nearly completely devoid of the white painted surface but I just had a quick fire when thawing frozen onion chips for 10 seconds. My previous, much less expensive microwave lasted nearly 7 years, so its a shame that a supposedly better model cannot match the longevity of the GE model. Looks aside, I would not recommend a GE microwave oven to anyone looking for a new or replacement microwave.

I have a GE Profile model JT965SK4SS micro/oven combo. It came new with my new home. A couple years into it, the paint (lining) interior of the microwave start to bubble and peel and eventually started rusting. Had SEARS come out (warranty had expired) who contacted GE and they concluded it was only cosmetic that it doesnt affect the functioning of the microwave. Well, its gotten a LOT WORSE now, bubbled peeling paint all over inside, rust, exposed metal, and the paint is falling onto food. I can NOT even wipe out the interior to clean it, it makes more stuff come off/fall down. I called GE last week, was told by 2 employees that it is NOT safe to use anymore, discontinue use. I had SEARS come again (per GE). The tech said he had NEVER seen anything like it before. He called GE to tell them its not safe, exposed metal, and its dangerous. They again said, well maam, youve gotten 8 years use of it. We wont replace it, but will offer you a discount for a new one ($2,500 out of pocket for me). The person who had offered me the discount (yes, I sent pictures, showed how bad it is) also gave me a tip regarding the unit I have now with the exposed metal and the chance of arcing (spelled? like Ark) if the unit catches on fire, make sure not to open the doors, the fire should contain itself. 2 employees told me its not safe, a 3rd gave me helpful info for if/when it catches on fire... and yet, they still wont replace the unit... and do not stand behind their own products. I plan to go to our local news station, see if they can get anywhere with this, since they wont do anything. Patiently waiting and unable to afford a new unit.

We recently purchased three GE Profile stainless steel appliances for our new home. The total was somewhere around $3500. Within two weeks our $1000 dishwasher would not work. It took FOUR service calls and THREE weeks for it to finally be repaired. Now our $2000 oven (traditional/convection) has stopped working and the oven light will not go off without us tripping the breaker. Service tech not available for 5 days. I am expecting the new micro to go out any day now. All of these appliances are less than two months old. We had GE builder grade appliances in our previous home that are still running strong after 16 years. That is the reason we went with GE again. However, after the above mentioned issues with our new GE appliances, I encourage anybody who reads this to NEVER, EVER BUY ANY GE PRODUCTS AGAIN.

I have a General Electric HVM1540DN1WW over the stove microwave that I have had. This month will be a year and a half. The oven stopped heating so being a DIY person, I pulled the oven out and took it to my workshop to see if it was something I could repair. Inside the front panel was a very helpful schematic of the whole oven. Using the troubleshooting step listed on the paper, I found that the Magnetron tube had gone out. So I went to my owners manual and found that the tube had a four-year warranty on it so I called General Electric consumer relations to have the part replaced. First I had to fight with them because they said it was only covered for a year. After about an hour and a half on the phone and giving her the publication number on the manual, she agreed that it was indeed covered for four years. So she said that she would replace the part and she would even send a technician out to install it at no charge. I was very happy at this point. She said that she would ship the part to me next day with UPS and the tech would be out the following day to replace it. So far so good, till the next day when the part did not arrive. I called back in to General Electric consumer relations and spoke with a man this time and he told me that she had canceled the order that is why I did not receive it, and he couldnt see why. So he looked at the comments she had made the day before and did see that she said she would replace it and send a tech. The tech was supposed to be here the next day and I had no part for him to install. The man said he would place the order and have it shipped to me by the next day no later than 10 a.m. and the tech would be here between 1 to 5 p.m. Great! Until the next day and again no part when they said it would be there. Again with the call only to find out that it was scheduled to arrive next day guaranteed by 7 p.m. The tech is supposed to be there with in the next few hours and I wouldnt have the part. I called Fed-Ex and sweet-talked the lady into getting a hold of her driver to see if she could get to me ASAP. Bingo, next thing you know I have the part, the tech calls and the part is replaced. Oh boy, the big gaping hole above my stove is finally going to be filled once again. (I promise I am coming to the end.) After reinstalling the oven, I found out that it was taking longer to heat than when I got it, and it has a brand new Magnetron in it.Again with the call to General Electric consumer relations to set up another tech to come out and check it out. So the following day, the same tech arrives and puts a cup of just barely cool water in it and puts it in for 30 seconds, pulls the water out and says it is working just like it is supposed to and leaves. Well, again I called General Electric consumer relations to let them know what has transpired, but this time I asked to speak with someone higher up the food chain. I then spoke to a lady and she said that she would set up another tech to come out and check it out, and if it resulted in the same way that she would replace the unit with a new one. The following day, the same tech calls me and said that the oven is working the best that it could so I should call back to consumer relations as he did and set it up for a new one to be sent in its place. So I called once again and was not able to speak with the same lady and the only thing she could do is send me a voucher for $250 laying around for a new oven, but I would have to purchase one and send the voucher in with the receipt to get a refund. I told her that I did not have a spare $250 dollars around to go buy a new oven and then wait for the refund to get to me. So I asked that she have the lady that said she would replace it to call me back to straighten this problem out. Finally the following week, the lady calls me back and said, This is the best that I can do, due to me voiding the warranty. I asked, What? She said that the tech that spoke with me said that because I had hard wired in the unit to the house wiring, it was receiving low voltage so she couldnt do any better than that. I told her that was the most asinine comment I have ever heard coming from a field tech and asked her whether he went to a school backyard Techs-r-Us. I asked if she would have the tech call me to explain. I also gave her some friendly advice that she should not use that comment to anyone else for fear of someone laughing at her. We agreed to have the voucher sent if that was the best she could do. I will not buy another GE appliance again! I have purposely not mentioned anyones name because it was the experience, not the person that I spoke with.

We purchased our new GE Over-the-Range Microwave (model HVM1750DPWW, 1.7 cu. ft.) for $269.00 in February of 2012 and in August of 2013 it started to malfunction. Specifically the microwave would start on its own whenever we would OPEN the door. Now the microwave does not work at all (with the door closed or open). Based on the feedback that I have read in some of the posts on this site, I will replace the microwave since the maker can no longer be trusted to manufacture units that are robust and safe. But what manufacturer can be trusted at this point? It is my understanding that all microwaves (from all major companies) are currently made overseas with poor materials and highly suspect safety and quality standards. (Note - previous GE Microwave [same type - over the range] lasted for 14 years.) Thanks to Consumer Affairs for allowing us to post unfavorable reviews.

I purchased a GE microwave just a year ago. Ive had a few problems with it like the round glass plate that you cook food on cracking in half twice when the microwave wasnt even in use, and the control panel going stupid... requiring me to unplug it to get it back on track. The worst part is I purchased an entire kitchen work of GE appliances at the same time and Ive already had two service visits on the dishwasher.GE customer service is the worst! When I call they just keep repeating themselves and they never listen to what Im telling them. Today was the worst yet... I got this woman on the phone and she just kept telling me the microwave was not in warranty any longer as of last month. She also told me she only has two appliances listed on my account (no range or refrigerator) when they were registered at the same time as the other appliances and they have sold me filters for the refrigerator several times. All I can tell people is if you are considering buying GE appliances... DONT! They SUCK!

Have a GE over the range microwave oven, MODEL PVM1870DM3CC which started turning itself on for 6 minutes, repeatedly, WITHOUT being touched!

Today my GE black microwave with rack mounted above the stove, caught on fire by itself. My husband and I smelled a chemical like smoke. We went in the kitchen and we saw fire in the microwave. We put out the fire and was thankful that we were home. If we were not home our house would have burned to the ground. The microwave was not in use at the time of the fire. I plan to contact GE about this dangerous event. My asthma has gone crazy since this horrible situation happened. I just want to let people know that GE microwave will catch on fire without being in use.

We have a GE SpaceMaker JVM 239BV 001 over the range microwave purchased about 10 years ago. Within one year of installation the handle snapped - just as numerous people here have stated. I went to our local replacement parts store and was shocked that it cost $30 for a new handle. The sales person said if I were you I would by the lifetime warranty for an extra $3 because you will be back, I sell lots of these.

I know this commonplace complaint, like thousands before me, will head straight into the wind because the world just works in this way: technical support and repairs works as a profit center for a corporation. My GE Profile microwave abruptly failed out of warranty after years of use. The cause was due to a wire burning up inside that had not been loosely connected, said the GE technician, so this was an issue of inadequate quality--not bad enough to cause the microwave to fail quickly but enough to cause failure over time.After taking the microwave out of the built-in cabinet, it only took the technician about 5-8 seconds to find and diagnose the problem, several minutes to get the right part (a wire) from the truck, and a couple of minutes to fix it. The labor charge was $121 for about 7 minutes of repair work, to be liberal with time. (This charge is separate from the charge to come to our home and diagnose the problem.) This prorates to over $1,000/hour for a basic wiring change, which I think is exorbitant. I understand that the technician is a highly trained individual, but this is already reflected in the high labor rate.According to GE, the cost to replace the built-in microwave, which came with a matching stainless steel frame would be $550 if we wanted the new microwave to match the frame at least (but not necessarily the oven, stove, etc.). This is the kind of cost you dont think about when you buy a new home built with matching appliances--well, I didnt. Companies like GE can rationalize all they want about all the overhead associated with servicing a repair call. I can certainly grant them some leeway, but in the end, charging an extra 8 times more an already high labor rate given the time needed to fix the problem is simply price gouging a consumer who has no good recourse. (This is why I pretty much avoid repairing anything, except for my car. Its almost never worth it.)I recently had an experience with an experienced plumber charging an hourly rate of $150, prorated by and rounded up to half-hour increments of work, regardless of difficulty of work. Repairing an appliance should work the same way, and my GE bill would have been halved. Because of such profiteering, I will not consider purchasing a GE appliance in the future. I pray that this microwave doesnt break down again in the coming years due to some other problem. It would be a lot less expensive to just buy a non-matching portable microwave then for $100-$150 than to keep up appearances.To be fair, the woman who fielded my service call was courteous and empathetic. Because the microwave apparently had an electrical burning problem, she previously waived the diagnosis fee. Otherwise, my simple repair would have run several hundred dollars, more than the cost of the microwave. However, she was unwilling to reduce the labor charge, so based on how strongly I felt ripped off, I give GE a star rating overall.

GE Adora Microwave DVM 1950 purchased at Home Depot - Update to a previous review. After speaking with Home Depot employees, GE service scheduler and finally Consumer Relations, that person agreed to schedule a repairman to come to our home and repair the microwave no charge. I certainly hope it can be repaired because until a couple weeks ago, I loved this over the range microwave. The warranty was for a year. We purchased it April 2012 but it wasnt used for six months so really only used 10 months, by two people!!

We purchased this new 8 years ago however the problems started after about two and a half years of use. I called GE when the paint started peeling off of the door of the microwave. They asked me if I cooked salty foods. I cook bacon in the microwave. They told me my only option was to buy a new door and have it installed. It was $250 at the time. I did not have the money or desire to fool with it. I continued to use the microwave and it has continued to degrade. Now eight years later there is so much metal showing that we decided we must do something. It is unsightly and very difficult to clean because its rusting. Ive been expecting electrical arcs to occur and the microwave to catch on fire. It hasnt done that. It has continued to cook the food. The entire metal area on the door is without paint. There are other large areas of metal and rust inside on the bottom of the microwave. The entire vent panel is without paint and rusted. We also had to have the control panel replaced twice. It was covered once under the warranty and once it was not. We also had to replace the element in the oven which is used rarely. To replace the microwave and oven combination now would be $3,500. When I do replace it I will replace it with a different brand.

Paint is peeling on the top part of the oven. It could fall into food. This seems to be a common problem. Called GE. They said it could not be repaired and to stop using it. Buy a new one. What kind of product do they put out that cannot be repaired? Not very good in my estimation. Customer Service did not offer much assistance to replace it. Be warned. Don’t buy GE products.

We have a GE built-in combination oven and microwave. The oven gets up to heat very quickly and bakes in less time than recipes call for baking. The microwave is an 1100 watt unit and performs equally well, and has for 29 years, Our cook top is a GE glass top unit, installed 11 years ago in a kitchen upgrade, performs equally well, though not quite as fast heating as our old gas unit but much cleaner and attractive. Have never required a service call on any of this equipment!

Our dishwasher has gotten very warm mid-cycle and now trips the breaker in the house each time we run the cycle. The problem became evident in April 2012. We have called in a GE repair person to fix it and they said it was a heating issue and not repairable. We have not used it since, but have not replaced it with a new one yet. In August, we read about the recall of a similar model number manufactured within same time frame. Our machine model is PDW7300J03WW, the recalled model is PDW7. Our machines serial # is **. Strangely, the serial number is not listed in the recall, even though symptoms are exactly the same!We have called GE Consumer Affairs at 1-800-386-1215 four times, the most recent today, 9/14/2012. Each time we call, we are left on hold for 59 minutes only to be disconnected automatically! I am sending a registered letter to GE CA with a copy of this link and intend to contact my local news if I do not receive sufficient response within the week. Does GE need to see an actual fire report from my fire department or worse in order to get their attention to replace the unit? It is disgraceful and extremely dangerous.

We were super excited to get this GE Profile Cafe dishwasher. Minus the brand, it was the exact design/style as the one my dad has which we love! First issue, dont have a name of a dish liquid if you cant use all of them. Cascade apparently makes different detergent styles for the smart dispense. Dishes were ridiculously dirty and the horrible thing is I couldnt find an answer why on GEs site, I had to go to a handyman site. That was about a month and a half ago. Today, I did the dishes and, of course, let it do its thing. I always have the heated dry on by the way. Well, dinner came and I grabbed some dishes out which were screaming hot and I had to use an oven mitt. I didnt think anything of it because sometimes Im a sissy about that. Well, its now 3 hrs later and I get up to the smell of burning plastic. My first thought was that the sippy cup straw fell on the heating unit. I did not, however, expect to open it and see the Tupperware melting, the silverware rack melting and the water bar to be melting to the heating unit and it being so hot that I have to use an oven mitt just to touch the freaking rack. Oh! And by the way, we bought this off Craigslist last year and it was brand new. It still had the casing around it from the store.

I moved into our house about 27 years ago, and have had to replace every single appliance except the microwave. The oven, fridge, washer, dryer, dishwasher—all replaced at least one time over. But this 90s GE microwave keeps humming along. I really should replace it just because it is this awful off-white color and everything else in our kitchen is part of a beautiful stainless steel/black/white scheme, but it is actually built right into a cabinet and I fear I will not be able to get another microwave in there. The only gripe I have about its performance is the fan comes on and roars full-blast anytime the stove or oven is on. It is so loud its difficult to talk over.

GE microwave oven (jes1651sj02) started to spark like lightning, which can be seen through the inside vent grid/grill located on the right. Sparks are seen just behind the waveguide cover where the magnetron is located. It seems to be a common problem with GE microwave ovens from what I have researched. The microwave has now stopped working and just makes an odd noise like groan or urrrrr. It’s just over 2 years old. Its a piece of **. It should last 10 years or more, like my last 2 have. I gave away our Sanyo because it wouldnt fit the decor of our new kitchen - wished I never had.

Since 2010, our 2006 GE 1.1 cu. ft. countertop microwave oven model # JES1136WL has had power failure problems. It began in our previous home and now in our next home. All of a sudden, Id check the panel and it would say PF, which means power failure. So, Id reset the clock and there it is, ready for the next usage. Over a year later, in our new home, as of yesterday, it will start and immediately cut off. Now, weve been using this microwave in the same plug since May and now its October. So, what happened? Today, Im looking for the users manual and have located it online. But it appears that the PDF GE has for it, the Adobe document, has a problem. So, Im going to check it on my laptop, as this is my PC. Thank God we only paid under $100 for it. On some of these consumer complaint stories, the person paid a great deal for theirs.

I also bought a stove as well as the dishwasher. We Told them with great concern to put a extra warranty on the more expensive item, which was the dish washer... more could go wrong. We all agreed, including sales person. Day before the first year, the dish washer was not draining good. They said the warranty was running out. I told them, I had got extra yr warranty. The robot voice said it might be over. The repairman came in, and said the same thing. The repairman replaced everything in the dishwasher. It took him 3 visits. He got it working. He claimed there was an extra orange ball in the part and that why it didnt drain well.I started using it for 2 weeks and it stop draining completely. When I bought it the salesperson said, See I added the extra warranty on. But unbeknownst to me, she put it on the stove... How the heck am I supposed to know she did it wrong. I call the company and they said, Look at your receipt. And sure enough, it was on the stove. Looking at it and how the salesperson made it sound, it was understood by all that the warranty was on and I had an extra yr on the dishwasher... I looked at the receipt. Had a list of what I bought the warranty and we were good to go. Everything was replaced in it, everything. It was a mechanical issue and yet here it sits not working and I havent even paid for it. I am disabled and was give a lemon. I would never recommend a GE anything. This was a first... I usually buy Whirlpool and never ever had a problem... Theyre selling lemons and they know it.

My GE microwave oven turns on by itself. The GE microwave oven model number: JVM1540DN1WW. The serial number is: RS903539B. My GE microwave oven turns on by itself usually as if the one minute express button was pressed in. This has been occurring for about 2 years and has been doing this normally when the air conditioner is not turned on. It appears this is a humidity issue. All summer it has been working fine. As the weather has started to be lower and we turned off the air conditioner, the problem has come back. When the temperature rises and we put the AC on again the unit will work fine. We live in Florida and it can be humid outside but with the AC turned on the humidity is lower and the microwave will work fine.