Its a beautiful piece of junk! I bought Stainless steel model #KGRA806PSS on January 2006. The first service call was on January 2007; second on January 2008; third on April 2008. Of course, my fourth service call is now past the 5 year warranty. The igniter would click forever and then go out. Three times Ive had the electronic replaced. Oven would preheat, come to temperature then would lose heat and never reheat past 275. I didnt dare use the self-cleaning feature after reading the horror stories of glass shattering or doors locking or burning the electric board out. Anyways, we called KitchenAid and after being told that they never have had complaints about this range, we told them that they should try looking at the complaints registered online. Well, since this would be the fourth service call about the same problem, they would send a service technician out and if its the same problem, they would pro rate a new stove. The service technician just called and said that hes on the way out and did you know that there is a $135 service charge? No, I will not pay the service call, after all Kitchenaid called and set up the call and Im not paying another dime on this $1500 money pit!Buyer beware. KitchenAid is no longer a customer friendly company and they do not stand behind their product. If they resolve this, I will report back but as my husband is on the phone and it doesnt sound promising, you probably will not be hearing anything more on this piece of junk!

I bought this stove July 2019 and it was the worst purchase I have ever made... I am going to give it away as I would not want anyone to pay for this piece of junk. It states that it as an Aqua lift self clean stove, but this does not work at all. I have just spent 2 hours with my head stuck in this stove trying to clean it again myself, but nothing works. The top is also very very very hard to keep clean and so for a clean junkie like me I now don’t even want to use this ridiculous stove. Take my advice and don’t waste your money... Anything else has to be better than this.

We recently installed our new KitchenAid combination microwave and oven to find several hundreds of fine fiberglass filaments protruding from the oven gasket. The owners manual contained nothing about this. I attempted to call KitchenAid about the filaments. Per page 22 of the owners manual, After checking Troubleshooting, you may find additional help by checking the Assistance or Service section or by calling KitchenAid. When I called, they cited numbers I encountered only a recording directing me to choose from ordering parts or scheduling a service call. I had to learn from non-KitchenAid online sites the filaments are fiberglass.The salesperson, from whom we purchased the oven, directed us to heat the oven to 350 degrees for 2 hours to burn those off and any other oils. We did not find anything in the owners manual identifying and addressing this. We do not want to suffer harmful health effects from eating fiberglass filaments in our food, there is a reason why people wear respirators while installing fiberglass installation. Why would KitchenAid think its okay to be eaten in food?Nor did the owners manual say anything about having to remove the entire appliance to change the microwave light; only that it is inaccessible. This was not disclosed to us when we previewed and later purchased the unit. We were further angered by what we have read today on this and other sites concerning exploding glass, locking doors and temp controls necessitating pulling the circuit breaker to shut it off, self-cleaning leading to exploding glass, inability to replace the microwave light without removing the entire appliance, and KitchenAids knowledge of all of this and more with an unbelievable lack of response reminiscent of Fords fatal exploding Pinto gas tanks and failing Explorer tires.We were already without a microwave and oven during several weeks of our kitchen remodeling, now my wife is afraid to use this appliance, wanting it removed from our home. Most likely, this will necessitate rebuilding the cabinet to accommodate another companys microwave and oven combination, and whatever additional expense and time that will require. Needless to say, after reading this and other complaints we do not hold our breath that KitchenAid will assist us in any way.We have contacted the appliance dealer from whom we purchased this oven to return it. We await his response. We strongly suggest filing complaints with the FTC and reference this and other sites in our complaint.

In May of 2017 my husband and I moved in to our newly built home. We purchased KitchenAid appliances. A dishwasher, a refrigerator and a stove. Shortly after they arrived I noticed that there were dents in the freezer door. They came to replace it. Then we noticed rust forming on the outside of the refrigerator. We had someone come and check it out. He told me to polish it more. That didnt change it in anyway. He came back out and said they will replace the doors.They ordered new ones. In the interim the new freezer door was getting rust on it. Then the compressor and the thermostat went out. They came to fix that problem. Now we are getting new doors and then they need to replace the freezer door. Now after all of this, the dishwasher is rusting. Our KitchenAid appliances have only been in our house for 4 and half months. I called the company, I called the place where we purchased them to replace them to no avail. We need help. We spent our hard earned money on a faulty product.

We bought all new KitchenAid appliances for our new home in late 2011. Two years ago I had to replace the refrigerator after losing the compressor. It was going to be almost $900 to replace the compressor or $1300 to buy a new refrigerator, so we bought a new fridge, but NOT a KitchenAid. Also in 2017 two of the five burner knobs seized up and could not be turned on. Another service visit and about $500 later these were fixed. Now this week I’ve had to call for service AGAIN because two other burner knobs have seized up and cannot be turned on. This will cost me another $400-500 again to get it serviced. I’m seriously thinking about replacing it with an electric range. It takes forever for the oven to preheat and also takes forever for water to start boiling. I WILL NEVER BUY ANOTHER KITCHENAID PRODUCT!! They used to be great but nothing but problems now.

KitchenAid double wall ovens/ WALL OVEN- ELE BI 30 - My LOWER oven (the one not used except on holidays) went out on me on CHRISTMAS as Im cooking a prime rib (at 500 degrees). The ovens have only been installed for a year! Got an error message asking for probe temperature. Wasnt using the probe although I do have the ability to use it. Checked the manual and found I did everything right. I then ended up with an under cooked prime rib for 13 guests. Thanks for that! Then I tried to clean the damned thing since it hadnt cleaned well after Thanksgiving (I usually try to do this when we are in bed because the fumes are so awful). Guess I know why it didnt clean! This time after waiting till everyone left, I opened the windows (glad its a warm December) and the oven wouldnt clean. Got an ERROR message this time of E3F3. Heck if I know what it means. They were able to schedule a service appointment quickly but if they have to order parts, then I have to have another service appointment. All I know is, Ive got an oven that doesnt work during the holidays (Im cooking for NY Day too). I called the extended warranty number and sat on hold for 42 minutes. THIS AFTER HAVING SPENT NEARLY 2 MONTHS TRYING TO GET MY BUILT IN KITCHEN AID DISHWASHER FIXED THAT HAS ONLY BEEN IN USE FOR 6 MONTHS! It needed an entire new drum. Nice since it already damaged my NEW cabinets and NEW floor in my NEW kitchen. No offer to fix the damage they caused even though they finally fixed the dishwasher. KitchenAid used to be really good appliances. NOT ANY MORE. I will avoid them in the future!

We have a Kitchenaid Superba stove and oven model KGRT607HWH6. It was in our house when we moved in 2004. It has a glass backsplash. Three years ago the backsplash exploded with my 10 year old twin sons and a teenage friend and myself standing within three feet of it. We are lucky we were not hurt. I think the pots cooking on the stove may have been touching the backsplash and it just got too hot. But, what a stupid design for a stove top! The repairman did order a new backsplash for $100. For years I would find tiny pieces of glass stuck in corners and crevices in my kitchen. I guess I should be ashamed to admit it, but I have never used the self-cleaning feature and the oven is quite dirty. I started to look for instructions on-line, but, after reading all the complaints I am scared to try the self-cleaning feature. The instructions say to not use a commercial product. Not sure what I should do.

After using the self-clean option on our Kitchen Aid range, the oven door locked, the oven could not be turned off or regulated, and an indicator light for the probe was on the display screen. Due to the inability to turn off the oven, weve had to unplug the unit, not use the oven, and light the stove top with a lighter. Ive read numerous complaints on the internet regarding this product and am applaud that KitchenAid has not recalled this item. Agreeing to replace a part through 2010 and not pay for the service call in unacceptable. We did not use the self-clean option until this year (2011) and had no reason to question the product prior. It is a very dangerous issue. KitchenAid needs to rectify this immediately.

My Microwave oven cost me more than 5000.00. After one year problem after problem. Never fixed. The service Provider Field Appliance is the only company they deal with which is another bad things. I called them to replace my entire unit, they refused it and they gave me coupon 40% off of their Website. Since the problem start I spend over 1500. 00 dollars to diagnose cost. This is really bad manufactured product. Its not worth for the money we pay. I prefer any other brand appliances to my house.

I purchased a resale home with existing KitchenAid appliances (four years old). In the short time I lived in my new home, I have seen multiple issues that doesnt seem normal to me. During cooking and when self-cleaning the oven, all the sensors turn off automatically including the clock and will turn back on its own after about an hour. It almost seem like the stove is overloaded even with one burner on. It shut the fan and all of the buttons on--the touch screen also stopped functioning.On 12/30/2011, while making dinner, the oven light came on and I cant turn it off. When I pressed the turn off button, it beeps and wouldnt turn the light off. It has been three hours and the light is still on and this concerns me very much as this is a safety issue for my family. I unplugged the stove and plugged it back in but the light is still on.

After researching many brands we decided to go with a friend’s recommendation for a KitchenAid gas range. After owning it for a few months now we’re very disappointed with the wear & tear. It was delivered with the side dented, which given our timely need, we decided to live with as it’s mostly hidden. We have found however that cleaning the stove top is very difficult (heavy pieces to remove and place back) and the stainless steel surface scratches and scuffs way too easily. If you’re a tidy person like me this will drive you nuts so proceed carefully with this one! After a few months it’s already starting to look worn in.

KitchenAid model KUDE70FXSS Dishwasher - Bought this unit in 2011. Out of the box, the control panel never worked right. I would frequently have to reset by unplugging and re-plugging the machine to get it to work. 3 years in, the control panel died and was replaced by the appliance store under an extended warranty. The top rack wheels have broken off twice and been replaced. Bottom rack wheels have broken off once and been replaced. Top rack after 6 years is peeling and rusted. Dishes will not clean completely unless you wash them first (kind of defeats the purpose of having a dishwasher) and the prowash cycle takes forever to run. All this time my wife has said, “We paid a lot for it and we will make it work.” FINALLY last week, a rubber spatula fell on the heating element and burned badly... stunk up the whole house. After days of fighting trying to get the burnt smell out unsuccessfully, I got my wife to agree to get rid of it and buy a new dishwasher.... It is NOT a KitchenAid. All that is left now is to get rid of the stove and refrigerator (yeah the stove/oven dont work much better).

While preheating, the inner glass of my KitchenAid wall oven exploded. KitchenAid was of no help even with the purchase of an extended warranty.

We bought a new KitchenAid gas range Model in 2014. The model# is KGRS505XSS. Within 1 year, one knob got stuck in off position. We had to pay $150 to service appliance person to get that fixed. Then less 1 year later a different knob has been stuck in off position. This is completely random and happens when were not even operating the knob. An amateur layperson cannot fix it. For the 30 years that we have been owning other gas ranges and operating it in similar home type situations, this has never happened to us. This KitchenAid unit is defective OR this could be a basic design flaw. Beware of this type of problem and do NOT buy KitchenAid for this reason.

My parents used KitchenAid while I grew up, I have been their customer myself for almost 50 years myself. My stove is over 20 years old and the only thing I’ve had to replace is the element. Excellent products!

Most unbelievable experience I have ever had in my life with an appliance (KFGG500EWH2), the other KitchenAid products have been fine? I bought this oven before Thanksgiving on 11-15-17. My wife just noticed now on December 25, 2017 that the top of the oven door and around the controls the white paint is turning Brown?!? I havent hardly used the oven but a half dozen times, a couple of pizzas and the turkey on Thanksgiving. We noticed on day one the stove top was more than just hot to the touch on Thanksgiving...more like untouchable!!! I will check the temperature now to see how hot it is getting.My guess is if it isnt a design defect, there may be some insulation missing in the door and or around the front of the stove top... Im not taking it apart to see why... This is more than disappointing. I will contact the manufacturer and the distributor ABT tomorrow to see what they will do. I have never seen anything like this before, this is the 3rd oven I have owned in my life, and never had this issue. I will post the receipt tomorrow if it lets me append this.

I have a 2-year old KitchenAid double wall oven. Today, I used the self-cleaning feature for the first time. After about 30 minutes into the cycle, the interior glass shattered! The glass blew through the bottom of the oven and into my kitchen. Fortunately, nobody was standing close enough to get hurt. I turned off the oven and circuit breaker to allow it to cool. I will be contacting the shop who sold this to me and also KitchenAid tomorrow.

I purchased a microwave oven, model KBMS1454SBL-1. About a year and a half into the product, the dashboard lights went out and stopped working. I went to the KitchenAid website and filled out their contact form in which they referenced I visit their service page. I filled everything out in on the service page. On that page it indicates the following: If your appliance is not under warranty or covered by a service contract, then the charge for the technician to come to your home will cover diagnosing the problem with the appliance, and a written estimate for the repair. To me that is vague. Does that mean that once the technician will do the repair, then I will be charged? Oh and also how much will I be charged? Well here is what happened.On March 23rd, 2013 I waited all day at home (wasting my time) waiting for this technician to come out. A representative from a company called A&E Factory Service came, looked at my unit and said, Oh, the dashboard doesnt work. It will cost $250 to replace it. I said, That is too much. Dont worry about it. I can order the part myself and do it myself as well. But it does not end here. He explained that now I have to pay him $129 for his service. I exclaimed why. He said, Well, that is what it costs! I was shocked. At no point did KitchenAid or A&E inform me of the cost for this service.April 26th I finally have time to call A&E and tell them I want a refund because no one at any point asked me if I wanted a service for $129. They explained that they would not give me a refund. I spent about 40 minutes on the phone with them and another 40 with KitchenAid, each blaming each other or saying that I should have assumed that it would not be free. But if KitchenAid does not state the cost and the contractor A&E doesnt explain how much prior to, how is that a fair practice? My service order number with A&E is **.I will never buy a KitchenAid product again. A&E explained that it does happen sometimes and that I should ask the KitchenAid management to do a conference call with A&E to get a refund. I called Kitchen Aid and they dont even consider the idea. They just say, Its not our problem. Your product is out of warranty so its not our problem. What a joke. A company that truly can give a rats ** about its products or customers! If I had wanted someone local to fix my problem like A&E and called them myself instead of doing the service through KitchenAid, A&E explained that they would have informed me prior to coming out. But because I did it through KitchenAid, then its not their problem. They are only supposed to show up, diagnose, collect money and then leave. Nice little partnership they got going! Screw the little guy, then waste his time and then try to overcharge for a part. Unbelievable! Never again! I will stick to brands that actually go out of their way and help their customers, whether a product is in warranty or not! Never again!

We bought all new Kitchen Aid top of the line appliances. Before year was up replaced 2 circuit boards in fridge. 1 in stove and dishwasher does not dry and leave a purple film in dishwasher. Have to bleach weekly. Now the microwave has broken for the 3rd time. Started with “close door” then no light, now absolutely no power. Blacked out. Absolutely disgusted with these appliances. Over 10g wasted. DO NOT recommend kitchen aid. Do your homework. Don’t waste your money.

Just replaced all appliances in our kitchen with KitchenAid. Very pleased with all but the double oven (Kitchenaid KEBS209BSS double convection). This unit is very well designed and nice to look at. It is also a very noisy appliance. There is always a fan running when in use. I understand the reason for the fans coming on but they are very loud and change sound pitch with temperature. If you are looking to buy one of these new ovens have your store operate it for you and see if you can tolerate the sound.

We have had two kitchenaid ranges in the last two years. The first one burnt up twice on the self-clean cycle and was replaced by a range with a higher speed blower fan that is extremely loud and annoying. Kitchenaid replaced the fan twice and have come to a conclusion that this is normal. When I first contacted Kitchenaid, their comment was we have had no noisy fan complaints. Service techs they have replaced many. Kitchenaid have told us they no longer going to help us with the noisy fan as it is normal. We are now stuck with a $2200 range. We will never buy kitchenaid junk again.

The unit is 2 years old. The Control panel was always hot. The repairman said that was normal. It was so hot that the cupboard Above the unit was being heated. Eventually the control panel blew. The entire unit had to be replaced. Next everything was burning. The repairman came & told us, You didnt calibrate the oven!!! They calibrated it and then told me that the setting will not hold. we will have to continually monitor the temperature in the oven.I baked two pans of oatmeal bars for my grandsons football team. One pan burned, the other did not. When I called about this I was told, You should have used the convection function. In other words it was my fault. I just threw out 4 loaves of German stollen because 4 were burned on the outside and uncooked on the inside. The remaining 2 loaves are fine. This oven will bankrupt us if we keep bringing in repair men. My question is this, Any suggestions for replacing this unit? Incidentally, we live in St. Joseph, MI, right across the river from Whirlpools Corporate Headquarters. NO ONE CARES whether the consumer is satisfied. Im fearful that this company will suffer the same fate as Eastman Kodak, in my hometown.

My husband and I bought all new kitchen appliances about an year and a half ago. We bought all KitchenAid: microwave, range, dishwasher and fridge. I always thought KitchenAid was a good company with good products... I was wrong. Within a matter of months, the range wouldnt work property. It couldnt be fixed so it was replaced. The replacement didnt work also and needed to be replaced! Five weeks later, we finally got a replacement range that worked. Now the fridge isnt working right. We have a French door with the freezer on the bottom and ice/water in the fridge door. It has been making loud noises and the freezer is not keeping items as cold as they should be and the ice maker stopped working. The warranty is only for a year so now after spending over $5,000 less than two years ago, we have to pay to get it fixed. We are stuck with the appliances for a while... they arent even paid off yet. I used to love KitchenAid but I will not buy one more thing made by them or recommend them. Beyond frustrated!!!

This range (Frigidaire Gallery 30 electric range model# CGEF304DK) was included in our new home purchased last year. The range looks nice but the oven racks repeatedly fall down causing the food and pans to spill out! This problem I was told was due to my neglect. Are they kidding? Steel racks are not long enough to stay in contact with the oven sides! The racks are not distorted or bent they just fall down. This could cause serious flesh burns and or a catastrophic fire if unattended for any short time period. KitchenAid totally abandoned their responsibility in this matter. Also the convection fan failed to operate. This upscale range is not older than 3 years, its a disgrace. We put tin cans in to support the racks when using the oven. Pitifully sad. DONT PURCHASE THEIR PRODUCTS.

I love this stove and oven, but follow the recommendations. Use the conventional settings to heat the oven, then switch to convection or it takes ages to heat up. The steam clean doesnt work as well as I thought it would, but it does work.

We have now had eleven service calls with the tech here up to three hours a call. The control panel has been replaced three times. The key board once. The sensor once. The temperature still goes from 325 degrees to 386 degrees after preheating two cycles. The bottom door hinges have been replaced twice with no change. Door still does not close properly resulting in bottom element not coming on. Whirlpool says this is all acceptable. For a supposed top of line stove, one should be able to bake without burning or undercooking. The manual says the oven temperatures are accurate. Not so!!

We purchased the new low profile style of KitchenAid microwave hood combination to replace a 21 year old Maytag model. I could no longer get parts for the old girl so decided to update. Installed the new unit in March of 2019. The performance of the microwave is as I expected from a higher end product. The model upgrades to LED lighting and the exhaust fan features are all pluses for this unit. The microwave touchpad and programs have worked very well. I would be rating this unit with 5 stars at this point except for one major flaw....There are (5) chrome buttons on the front face of the microwave to control the lighting, fan, open the door, cancel program, and start menu programs. On the surface of the buttons lettering had been stenciled to identify the function for each of these (5) buttons. After about 6 months of use the lettering has become faint and/or disappeared. Of course the two buttons used the most START and OPEN are now basically missing any lettering to identify the function of that button.In September I decided to contact KitchenAid Customer Experience Center about the problem. I first used the contact via e-mail found on the KitchenAid website explaining the issue with the button lettering disappearing. Received a response about 5 days later stating they were sorry I was experiencing and understood it could be frustrating. Then went on to state quote When touching the control panel, be sure there are no oils or lotion on your fingers. This can damage the lettering and finish.. They would be sure to pass on my complaint for review and future improvements. Of course this response did not sit well with me. What kitchen appliance should not stand up to normal use with your skin oils or other kitchen products touching its surfaces.I then called to arrange for a service call on the microwave again explaining to the representative my issue with missing button lettering. After much discussion of the problem they basically categorized the problem as cosmetic and therefore excluded under their warranty. The warranty in the User Guide also stipulates in bold lettering The cost of repair or replacement under these excluded circumstances shall be borne by the customer. No service call was set up at this point.After a couple more e-mail exchanges with Consumer Correspondence Team personnel, they recommended I arrange a service call to have a local KitchenAid repair technician look at my problem. I asked them to waive any costs for the service visit IF the technician could not classify the defect as anything other than what they had already called cosmetic. They could not provide me with such a waiver and no service call was arranged.I would say the Customer Experience Center personnel listened to my complaint and understood my dissatisfaction, but could not help resolve the problem. I even asked them to just send a set of new buttons and I would be a happy customer. I dont think that is going to happen either. No further communications for a couple of weeks now.Like I stated earlier, I now have (2 of 5) buttons without identification as to their function. The User Guide does not pictures of these buttons so you cannot lookup what the buttons do, good thing for our memory I guess. The frustration is the lettering should be able to withstand normal use in a kitchen environment without rubbing off. It is more than a cosmetic issue. Thus the reason for the 2-star rating for this appliance. I just want current and future customers to be aware of this issue. A photo is attached of the right hand side buttons showing the lettering disappearing with use.

We bought this KitchenAid Range in December 2015. One year and 2 weeks later the oven stops working on Christmas Day. No longer on warranty. This is the worst appliance I have ever owned. It takes a long time to preheat and the bottom baking drawer doesnt seal well. I wrote an email to KitchenAid customer service and have not received a response. I hope this review prevents others from buying this expensive, undependable range. This is a real lemon.

Our experience with Kitchenaid has been a disaster. Their response? Complete indifference. My wife and I bought $10k worth of appliances less than two years ago. The first to fail? The dishwasher routinely flooded the floors. After the 4th repairman came to our house our dishwasher was replaced. The first two repair visits the repairman suggested maybe we were putting our dishes in the unit incorrectly and the second time he said maybe we were using the wrong soap. Really? Our wall oven has required two visits from repairmen to recalibrate the controls because when it said 350 degrees it was actually 250 degrees. Now the unit wont get out of the preheat stage.And now after spending Friday morning away from work to have $750 worth of replacement parts installed by a repairman, the refrigerator is broken again - including water all over the floor. We did purchase an extended warranty with the products through Best Buy. EVERY TIME we call Best Buy they do their best to point the finger at Kitchen Aid and Kitchen Aid responds with a we could care less about your problem.” So whats next? We continue to get our appliances fixed (that is until they break again) but we need help with getting Kitchen Aid and Best Buy to care.

KitchenAid Aqualift model KGRS306BSS - This is by FAR the worst oven I have ever had the misfortune of purchasing. Where to begin...? The glass door has condensation build up between the outer and inner panes. The oven heat vents through the FRONT of the oven door right below the gas burner knobs which makes them hot and difficult to use when both oven and burners are in use. The gas cooktop itself has so many indentations that cleaning spills/residue is a multi-towel project by itself not to mention the materials used to make the cooktop hold on to residue like Ive never seen. Theres another oven heat vent at the rear of the cooktop below the control panel for the oven which can heat up the key pad above it. When the oven is in use for prolonged baking (think turkey), the rear right burner gets hot when not in use. If I could shout it from the rooftops I would tell the world not to buy this oven and to forget about KitchenAid all together as an appliance brand.

Kitchenaid KFIS25XVM - We purchased all Kitchenaid appliances for our new construction home. The dishwasher, microwave, stove and oven and refrigerator have all broken. The service department could care less. I will never purchase Kitchenaid appliances again and I suggest you purchase another brand as well.

Bought fridqe 5/30/13. First Geek squad guy was at our home in August due to water dripping inside fridge. Geek squad was out at least 7 other times, replaced everything inside stove too (kept turning itself off). Bought extended warranty from Whirlpool, but not really whirlpool. Assurance is extended warranty company? Started sending AAA appliance out, theyve replaced everything inside at least once, some twice. Still doesnt make ice and leaks. They call whirlpool but apparently should be calling Assurance. AAA can’t fix it, told whirlpool it needs to be replaced. Assurance knows nothing about it? What a nightmare. Ill never buy whirlpool again. Just want what I paid for!!

Purchased range KSEG950E in January 2016. The oven never has worked properly. I have had service out at least a dozen times. Purchased the extended warranty out of necessity and have regularly had technicians out for service. I’m told each time that there is nothing wrong. My oven does not hold temperature. I set it and it will vary up or down 50-75 degrees during baking time. This is totally unacceptable to me as a baker. I am very disappointed in KitchenAid, I usually love their products. We are about to trash this very expensive range and buy another brand!

Buyer Beware! My partner and I bought a $6,000 KitchenAid 36-inch dual-fuel range about 12 years ago. Since then, the oven has failed three times, the last time for good. When I called the manager of the expensive appliance store where we bought it, Cocoplum, in Essex Junction, VT, he told me that we had a lemon and went on to say that the company was no longer any good. The problem, according to him, is that the high temperatures of the self-cleaning oven (which we have not used often) do not play well with the complex electronics of the stove. Bottom line: after 12 years, we have had to plunk down $7,000 for a new stove, this time a Thermador with gas only. There is a class-action lawsuit being brought against the company in New York, and other reviews online confirm our expensive bad experience.

We purchased a white Kitchen Aid gas range (model #KGRS206XWH2). Less than two months after installation, the lettering on the burner control knobs is dissolving off, and smears off with the touch of a finger. I called Kitchen Aid for new knobs, and they said they would send new control knobs as a one time courtesy. They do not consider it under warranty, as they call it a cosmetic issue. No chemicals, or abrasives have been used on these knobs. It is not a cosmetic issue, its an engineering defect, and a safety issue. Unless you want to live for years, with a range that has no lettering on the burner control knobs, dont purchase this range!

Just remodeled our kitchen and chose a KitchenAid group of stainless steel built--in appliances. The microwave can also be a convection oven and is wide, tall and very user friendly. Installed above the oven, it is attractive and efficient and we are totally pleased with our appliance choices.

I bought the fridge last November (2013) and the freezer has quit working. I am so sick of the quality of American products! I also purchased a KitchenAid dishwasher and the pump went out on it within the first 6 months. I am single and run it MAYBE once a week. When it came time to purchase a gas range I decided to ditch the so called American made KitchenAid brand and go with the Bertazzoni (Italian manufacturer, family business-6 generations strong). NO WAY was I going to purchase yet another KitchenAid that would need repair within the first year. In hindsight I wish I would have purchased a Bosch dishwasher and did more research on refrigerators. I would NOT recommend ANY Kitchen Aid product!!!!!!!!

Our family has had problems with this microwave since we purchased in 2007. Realizing that recent history has proven manufacturers of some appliances cut overhead by skimping on parts made overseas, I assumed KitchenAid was a safe bet. I could not however have been more mistaken. I am what is considered a journeyman carpenter, mechanic, electrician and DIYer. So I assumed, again, mounting our new microwave should not have been space shuttle science. I was shocked and surprised to see how fragile the front intake grill design really was especially coming from a reputable company such as KitchenAid. If youre not extremely careful just mounting the intake grill where its supposed to attach could result in undue stress to the plastic tabs and cause them to break. The operative word being plastic unfortunately, not the real metal it is made to look or function as. Why were these at least not reinforced? About eight months later the main control board started giving us grief. Sometimes it would lock up or beep for no reason and other times would work fine. We lived with that for some time until the handle broke after a year and a half of normal use. By the looks of it, it seems the proximity of the heat from items being cooked caused it to crack mostly near the top where the handle is mounted, again causing stress fractures and ultimately causing the failure. I have been the sole provider for my family so money was something we cant be frivolous with. Weve ended up having to unplug the unit due to issues with the main control board. I am now in the market for another microwave and I will not buy another KitchenAid product. Unfortunately for my wife who has to match styles (since the range is also KitchenAid), this wont be an easy task. Ive always thought highly of this brand but I guess this new generation of people in manufacturing isnt what they used to be. Signed, DISSATISFIED CONSUMER.

The issue I am currently having is trying to get a new control panel for our built in refrigerator. The day after Christmas the refrigerator went out. The following Monday I called a local appliance repair business so we could get the refrigerator fixed. They showed up the following day and informed us it was the main control panel that was out and this part was not available. They suggested we either were going to have to have the control panel rebuilt or if that did not work the only solution was to buy another refrigerator. I found that hard to believe so I called KitchenAid and eventually got to the Built-In Department. I was told the part was getting ready to be available and would be ready for distribution on 1-7-16. Was also told until now this part had not been available due to the manufacturer being destroyed in a storm and it had taken them several years to redesign a part that actually worked. I also found that hard to believe. However, I now thought all issues were taken care of and excepted the wait. Well, yesterday I decided to call checking on things only to find the part did not go out as stated and there was still (0) showing in their availability. The parts distribution company that our repair shop orders their product from had not even placed an order because there was still 0 showing available. After several phone calls and talking to several different people my frustrations only grew. It appears that even though the folks in the built in department could see the inventory was available nobody was able to order the part because the part is still not showing up as available in their system. Finally, the part was made available for me to order, shipping at my expense, to be shipped to my repair Co. I also then found out that I would then be responsible for shipping the core back and that I would have NO warranty on a $350.00 part. If the part was ordered through my repair Co I have a warranty and no shipping expense. They were not even willing to ship next day or 2nd day mail. For a part this expensive and with as many issues it appears there have been with it, I decided I needed the warranty so Im back at the mercy of KitchenAid and the wholesale part supplier to get the part to my repair Co. I found the policies at KitchenAid and the procedure they go through to be very non-flexible and not consumer friendly. In addition, we put all KitchenAid products with the exception of our gas stove in our house. We have already replaced the built in Ice maker and the microwave. This will be the last KitchenAid/whirlpool appliance we ever purchase.

We built a new home in the Rio Grande Valley in 2005. Since we had previously remodeled our home in Irving, Texas using KitchenAid products which gave excellent service, we assumed we could rely on newer models to do the same. This was a mistake. We installed a stainless steel oven/microwave combination (Model No: KEHC309KSS 05, Serial No: XS060040 57). The microwave door springs continually break and the light bulb burns out regularly. The product requires a service call every year. It requires two men to change the microwave light bulb because the whole unit has to be pulled from the cabinet. One man must hold the unit while the second replaces the bulb. Even though the service people are told they must send two men, they seldom comply, requiring the scheduling of a second service call. If we did not continually purchase extended warranties, there would be no way to keep the product operable. After reading all of the posted complaints, we are now afraid to use the self-cleaning part of the actual oven. This was a poorly designed product which never should have been marketed in the first place. After a two page letter listing the number of service calls and the problems, we received a call from KitchenAid stating they had received the letter, had no record of any previous complaints and were relaying the information to their engineers. It sounded as though there would be no follow-up and no effort to resolve the complaint. Its amazing that a company can continue in business with so many complaints against it by relying on past reputation. We would never recommend a KitchenAid product again.

My Kitchen Aid double oven which is still under warranty was not heating up properly and when it did heat many, many items came out burned. I checked the temperature with an oven thermometer and the temperature was way off when the beep sounded that the desired temperature had been reached. It took about 20 minutes longer to reach the correct temperature (35-40 minutes in all).It is loud both pre-heating, cooking and cooling. I sent my complaints to Kitchen Aid. A repairman came out and told me the beep really doesnt indicate the temperature had been reached. Must heat another 20 minutes at least and put bread in the oven and see which pieces come out burned to identify the hot spots. Dont want hot spots? Use the convection feature and bake at a lower temperature. It rattles and whirrs and makes a deep throbbing noise. Apparently this is all normal!Called Kitchen Aid, said nothing had changed. Talked with a rep, then her supervisor. She kept with the party line and repeated what the repairman had said but added, If you open the door, heat will escape. I hope she didnt say this with a straight face!! To top it off, this is only 1 authorized repairman in our area. Guess who?? NOT OKAY!!!!!

KitchenAid range KDRU783 - This stove has been a nightmare. First, the right-hand front burner was burning with an irregular, bright yellow flame. Called repair; their assessment Lady, you just need to use a bigger pot. (Pardon me, Im a chemist by training, I know incomplete combustion when I see it.) Called again, no better luck; spent several years putting up with carbon deposits on my pots. Finally, the burner became unusable; it literally burst into flame and sent up black smoke. This time I called the repair from the store where I bought it -- a well-known chain -- and they sent a technician who spent time investigating. Found the problem -- a connection to the propane line had come loose. Then, an additional problem occurred: the touch panel would start clicking when we used the left-hand front burners. It would flash on and off at 350 degrees, or 500 degrees, or some other setting but would NOT turn off. At worse, the entire stove -- both ovens -- would become inoperable. This second problem resulted in 3 trips by the repair people, who replaced the unit twice and then a third time with no change. However, the 3rd set of technicians think they have figured out whats going wrong -- and I have an appointment the day before Christmas, thank you very much. Right after they left, a third problem occurred: the left hand back burner next to the griddle keeps sending sparks; we have checked that one of the covers on the burners might be off center, but thats not the case. The result is that the only way we can stop the sparking is to keep the burner turned on low (so that we can use the other burners and the ovens) or to turn off the circuit breaker. I would like to hear from other people who have this range and find out whether this might be a common defect.

I purchased KSSO42QTX refrigerator in December of 2011. It cost over $5,000.00. Within 3 months, the unit had frost and ice accumulating in the freezer and poor cooling (high temperature) in refrigerator leading to spoiled, wasted food and on several occasions, illness due to spoilage. I contacted KitchenAid on several occasions over a two-month period and was directed to defrost unit and start over. When the problem persisted, they finally agreed to send a technician. The independently contracted technician found defective fans, motors and gaskets. I requested that the unit be replaced being that it was a lemon, having proven defective after only 3 months of usage. The technician and KitchenAid customer service said they will repair, but not replace the refrigerator. I was told to defrost and shut off the refrigerator. I waited for approximately two weeks for the independent repair company to receive the new parts and make a return appointment. When they arrived, they realized that they had been sent the correct fan parts, but not the correct gaskets. The technician refused to repair the fan as he only gets paid at the completion of the job and refused to repair the fan, which would have created an appropriate cooling environment for food storage. We are currently waiting, again, for over 1 week for the new part to be delivered. I have now been without the use of a refrigerator for approximately 3 weeks in sweltering summer heat. My wife has had to take 2 days off from work to accommodate the technicians schedule and will be required to take another day leave from work to accommodate for another appointment.Throughout this process, KitchenAid customer service has been terrible. They were unconcerned that our refrigerator has been spoiling food. They were unconcerned that the unit proved to be defective after 3 months of usage. They were unconcerned that we have no refrigerator in the middle of a summer with temperatures hovering around 100 degrees. They were unconcerned that we had several instances of illness due to spoiled food. They have been unwilling to replace the lemon refrigerator, which broke within 3 months of purchase. They have been unwilling to expedite any service or delivery of parts in order to alleviate this egregious situation. They refused to use expedited mail service. They refused to appoint another independent technician when the one originally assigned refused to provide timely service. We are still waiting for the repair to be completed. I have been offered no compensation for the trouble that I have had due to the lemon refrigerator.

My Kitchen Aid stove has been a nightmare. Not quite three years old the top has clacked and the glass window in the door has shattered. When I contacted them the first thing they asked if anyone was hurt and was there any damage to my home. When I told them no, that was the end of their concern. The door shattered while my wife was cooking a stake and it made a one big boom! I was told I would have to pay for the repairs. I also purchased a Kitchen Aid microwave and dishwasher at the same time. Now I worry they might fail and cause a fire in my kitchen.

As a retired chef I have preference for gas cooktop but electric oven. I built a new home with floorplan that did not offer separate cooktop and wall oven so I was very pleased when I found a Kitchenaid dual fuel product offering gas cooktop and electric oven combination. I had past experience with KitchenAid and thought I was purchasing a quality product.Although the cooktop and oven function well, the so-called AquaLift self-cleaning feature is useless! I do not let my oven become heavily soiled but found my first use of this feature did nothing to clean the oven. Even worse, instructions indicate even if I was willing to use an oven cleaning product and elbow grease I am warned this will damage the oven surface. It appears there are currently class action suits on this topic. Wish I had known this before purchasing this expensive product.

I have had problems with my KitchenAid gas range right out of the box. I purchased it for $2500 about 4 years ago. Just after the first year, self-igniting elements failed, so I phoned customer service - the worst customer service I have ever experienced! In short, a $500 repair bill to have a tech repair the problem. I have been using a lighter ever since! The convention oven worked 50% of the time. After one year, I finally have to go buy a new oven after only 4 years because the pilot failed to ignite the gas oven - very dangerous part to fail. I will never buy another KitchenAid product as long as I live. KichenAid Brand is owned by Whirlpool, and I will purchase any product Whirlpool sells. Save yourself a pile of money and grief, find a better product to purchase.

I bought KitchenAid oven on 8/2002 KEBC208KSSO. The control board was replaced in 8/2006, again in 2/2007. Again, the control board has failed and needs to be replaced! Is this a quality product? KitchenAid refuses to take responsibility for a crappy product.

In 2012, I purchased a KitchenAid Refrigerator, model KFCS22EVBL. Weve had nothing but problems with this product. First, the freezer leaked water onto my beautiful hardwood floor. The refrigerator was repaired but it ruined my hardwood floor. My research indicates that this is a known design defect. I wrote a complaint letter to a Whirlpool executive, who referred me to their quality assurance expert. What a joke! I was left extremely frustrated and angry. Neither Whirlpool nor its QA representative understand the concept of customer satisfaction. Second, the refrigerator is extremely noisy. We have an open floor plan and sometimes we have to speak over noise from the refrigerator to hear conversations. Lastly, cleaning the coils is a nightmare. The user instructions state There is no need for routine condenser cleaning in normal home operating environments. I dont have pets; however, due to dust buildup, I need to vacuum the coils at least 2-3 times a year. Additionally, dust tends to collect behind the front coil and there is no way for the average consumer to reach the area behind the coils. Yet, Whirlpools instruction states Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area on the condenser. Gee, I wish I can figure out how to get behind the front coil. (The attached image shows unreachable dust behind the coil). I suspect the refrigerator was purposely designed this way to shorten the lifetime of the refrigerator. Whirlpool has underestimated this consumer. I will no longer purchase another Whirlpool product, especially since Im also having problems with my KitchenAid double oven. Im now looking for another refrigerator.

I installed Superba double oven in 1999. Self-clean caused computer board damage first two times we used it. They installed a modification kit on the third time. That has helped, but I just tried self-clean again last night (stupid move) and control panel went dead. Im waiting for repair call. I guess we wont be doing Christmas party or Christmas dinner for family unless we use the stove and outdoor grill.

If I could rate this company any lower, I would. I have a Kitchen Aid microwave (TR71834046), Refrigerator (KRFF707ESS01), and dishwasher (KDTE334GPS0). All were purchased 3 years ago along with a range. I have had to file 10 different claims on the items listed above in those 3 years. I also have had to purchase several warranties and extensions to make sure I am not completely screwed. For how much money I have spent, you’d think their customer service would at least be worth it. Think again. You have to wait for at least 1 hour before ever talking to anyone. So I’ve spent well over 10 hours just on hold with this god awful company. Each time they then set up a date in the not so near future for a repair company to come out and sometimes even then the job is far from over. I am now awaiting a company to come fix 3 different things on 2 different appliances. This after they were just out 3 weeks ago repairing something else. I HIGHLY recommend you stay VERY FAR away from Kitchen Aid. This company is absolute trash and uses the cheapest of plastic to make their products. I will NEVER buy ANYTHING from them again.

Our stove caught fire and nearly burned our house down! The range was a $1500 unit just over 2 years old. A wire to the oven element failed catching the wire insulation on fire and started to navigate to the wall of the house. There was nothing in the oven at the time and it was being preheated for potato cakes. Pictures are available and will be used for an Attorney in order to regain damages.

My mother passed 4 and a half years ago and gave me some money so I decided to invest in a nice gas stove since my daughter went to culinary school. Less than four and a half years one burner went. Locked up. Second burner went. Handle locks up. Third burner went. Handle locks up. This week my oven quit working. It has a small oven on top. Big convection on the bottom. Now the big oven convection oven totally quit working. What a waste of money.

I have a french door refrigerator (Model KBFS22ECMS00 purchase date 1/27/15) and gas range (Model KGRS202BSS-1 purchase date 1/19/15) that have issues. I called 2 weeks before Thanksgiving about the freezer not maintaining temperature (set at -6 degrees, maintaining 6-15 degrees) at time of call. Several days BEFORE Thanksgiving, the refrigerator started doing the same thing (set as low as possible, maintaining 45+ degrees). On the day of Thanksgiving, my oven refused to maintain set temperature. It would get to temperature then the igniter failed to ignite the gas and maintain the set temperature. No smell of gas in the house.November 30 when service techs arrived, it was discovered my condenser leaked all the oil out and the compressor had locked up. They had to order parts. Had a service date of 12/16 to repair the refrigerator and troubleshoot the issue with the oven. Was called the day before by Video Tech Services (the servicing company) to cancel my service appointment because one of the refrigerator parts was on backorder. Called KitchenAid/Whirlpool early last week and lo and behold, THEY had the part that was on backorder so I have no idea where the service company is getting their parts from. Parts were sent to the service company 2 day shipping so they SHOULD have received it last Friday (12/18)... At the latest.I called KitchenAid/Whirlpool again on the Tuesday (12/22) since I had not received a scheduling call from the service company. Interestingly enough, the servicing company received the backordered part on SATURDAY (12/19) but had since FAILED to call for a service appointment. Now mind you, this is going into a SECOND MAJOR HOLIDAY without appliances. The service company finally called 30-45 minutes AFTER my call to the manufacturer. I am now scheduled for a repair on January 15 because I refused to take another day off from work (11/30) to accommodate them. I had taken the day off on 12/16 as well. Both appliances 10 months old (actually the refrigerator was 9 months old (delivery date of 2/22)) before failing and 60+ days before repair? Through two MAJOR holidays???

I purchased the KitchenAid KESK901SSS Electric Slide In Range five years ago as part of a kitchen remodel. My experience is that the product is inferior and cannot withstand normal use, and parts are prohibitively expensive. A few years ago it cost me $600 to replace cooktop after a bottle fell on it and was not covered by insurance. More recently, after spilling water on the stovetop the oven control unit stopped working. Who would engineer a range that cannot withstand a water spill??? I was told by the technician sent by insurance carrier that replacement parts again were expensive -- in the $500-$600 range. Since I had insurance, I thought that this would be an easy fix.After waiting two months, it turns out that the replacement parts are unavailable! The best insurance would offer was a buyout at a fraction of the original cost of the product. I checked with a reputable appliance repair shop to see if I could have it repaired on my own. They wouldnt touch it... They said that parts were expensive, could not guarantee that it would even work, and that they have gotten stuck in the past. I am now forced with the inconvenience and expense of purchasing a new range at current prices which are twice as much as original model. In addition, since the original product did not slide in flush to the wall (there is a 3 gap), I need to have my custom granite countertop modified to accommodate a new range. I am very dissatisfied with KitchenAid (and its parent company, Whirlpool) quality and service.

I like the dishwasher. Stainless inside - great and stays clean and does not stain. I also like the shade of the white model. Washes consistently well. Nice arrangement of racks and silverware holders. It fairly quiet but not silent for sure. Purchased in about 2002. Only complaint is that the dishwasher sometimes leaks. Had a plumber here a bunch of times and Ive arranged dishes differently a bunch of times and neither the plumber nor I can figure whats causing the leak so I mop up with towels when it happens.

This is the second review I am writing about this oven. The first review I wrote was a couple weeks after it was installed and I gave it 5 stars. Its a beautiful oven. The stovetop/burners work great. The top oven is the one I use the most and at first it was fine, but after about a month, I noticed the blue interior is peeling off the base plate on the top oven and black splotches started appearing. I removed the base plate and tried to clean it but there wasnt anything on it. The blue was just disappearing in places. I took the oven plate back to the store I bought it at and they ordered a new one.The second plate started doing the same thing after only a couple of weeks. The blue coating is clearly not perfected and I really wonder if it is releasing chemicals or flaking off into the food. I cannot recommend this to anyone. KitchenAid - you need to do more testing before you release products into the market. I am a product developer - I know when something hasnt been tested appropriately. Im waiting for my third base plate to arrive but I am likely going back to the store to tell them to replace the oven. My preference would be to replace it with a different brand, but the over the oven microwave that a purchased at the same time is also KitchenAid brand (ut-oh).

I have a model KEBC107KSS04 Superba Self-Cleaning Electric Wall Oven/Convection. Self cleaning causes the oven to malfunction or breakdown. We cleaned the oven once and had to pay for a costly repair. Oven would not go up to desired temperature. Oven temperature stuck on Low . We cleaned the oven a second time and the same malfunction occurred. I’m not willing to pay for a second costly repair. KitchenAid, I am sure is aware of the problem. Just reading the complaints made me aware, I am not alone.

Bought a great looking KitchenAid oven last year, but it has an unusual malfunction of blowing hot air from the oven into the kitchen for extended periods of time while the oven is on, and most annoyingly, after the oven is turned off. It heats up the kitchen so much it is uncomfortable to be in there while cooking anything in the oven.Just now, we turned off the oven more than an hour ago, and incredibly, the fan in the oven suddenly turned on and for about five minute spewed more hot air into our kitchen. This is a major malfunction. Previously contacted KitchenAid, but the phone operator could not help and thought this was normal. This cannot possibly be normal. It probably heats up the kitchen by 10 to 15 degrees, which is a killer. DO NOT BUY THIS STOVE/OVEN.

After a year and half, I had to have the repairman come out to fix the oven. $230 later, it worked. But now the oven is less than 5 years old and the oven will not work. And the over-the-range microwave will not work either. I will never buy another KitchenAid appliance again. I have had other microwaves and ovens from different brands that lasted three times as long and were much cheaper! Stay away from KitchenAid products unless you like throwing away money!

Purchased our Double Oven July 29/11 from a local appliance shop (Herbs Appliances), authorized dealer for kitchen aid. From day one it did not work properly, convection fan made noise, in all fairness Herbs came back and fixed that. Then the electronics board failed. Had to turn breaker off and on, to reset it constantly. Well, now Herbs Appliances was not so eager to return and did not return at all. Excuse after excuse why he could not come. Then the upper oven failed totally. Called Kitchen Aid said it was no longer under warranty. Absolute nightmare from Retailer to manufacturer. To add insult to injury, we purchase a new cook top from Ikea. Nutid Induction cook top. It lasted 6 months, half the burners failed. To my surprise it was another kitchen aid product. To nobody else fault but my own, I have misplaced the receipt. No warranty. Big Box to supporting your local retailer, dont buy Kitchen Aid.

I have purchased two KitchenAid gas ranges (yes, I should have learned my lesson the first time!). Both have been seriously problematic. Within a year of purchase, both locked up when I cleaned them for the first time, and I could not use them without a tech coming to my house to repair. One of those ranges had a faulty fan which did damage to another part due to overheating during the cleaning process, which resulted in damage to other parts! Most recently, the electronic range control on my Architect II went on my three-year-old gas range. So back to the repair techs. I will never purchase another KitchenAid stove. Based upon my experience and that of others, they are simply poorly manufactured and not reputable. Repair costs are ridiculous and I am thinking of replacing mine due to the high repair costs and lack of faith in this happening once again, at a time when I really need to use the stove!

Remodeled kitchen and purchased 4 kitchen aid appliances - thinking they were of great quality and would last. Had nothing but problems since purchased shortly after purchased. Had problem with microwave door problems with fridge - ice maker. Problem with oven when self-clean - shuts down and cant open door. Had fixed 2x -this is the 3rd time! Dishwasher fixed more than once - refused to get fixed again and pay over $300 - can buy a new one.I currently have an ice maker, dishwasher and oven that does not work. Raising 4 children, I am VERY dissatisfied with Orvilles where I purchased the appliances and ESPECIALLY KitchenAid - that doesnt back up the products they manufacture with defects. I will NEVER purchase anything KitchenAid EVER again or shop at Orvilles. I have paid so many service charges and part bills. I refuse to give them any more money!

Range KESS907XSP02 - Turned on brand new $2,300 range, wow can you say loud? KitchenAid arranged for a service call, turns out that is how loud this model is and there is nothing they will do about it, no refund or exchanges allowed. I would say us as consumers were not informed of this obnoxious feature. We would not have special ordered this model if KitchenAid would have disclosed this flaw. We sit and cringe when cooking in our new kitchen. The loud sound is not our imagination, friends and family agree. I bet no one at KitchenAid has this model in their own home unless it was given to them for free. What a waste of money.

If youre thinking of buying KitchenAid major appliances, read the letter I recently sent to KitchenAid below. I got a legalistic form response offering nothing, not even an apology. They even got my name wrong. Never again.I am writing about a series of problems I have had with several large KitchenAid appliances. I have never written a complaint letter before, but the coincidental problems with your products reminds me of the planned obsolescence complaints from 30 years ago about American made cars. I thought about just posting all of this on the internet, but thought I should give you a chance to respond first. Here is my story. On December 2, 2004, I bought three major KitchenAid appliances as a part of a high-end kitchen renovation. A built in refrigerator was the big ticket item, but I also bought a gas stove/electric range, and a silent dishwasher, all brushed silver. Together, the three items cost me $11,494.35.Everything worked fine until this past spring, but within six months, all three appliances have had major problems. The compressor on the refrigerator failed. You covered the parts, but I paid over $600 in labor. A hinge on the door of the dishwasher rusted out, and I replaced it for over $300. Currently, the washer motor on the dishwasher is screaming every time it runs. Ive been quoted a cost of about $500 to replace it. What about the stove? This past summer the small control board (near the dials) failed, and I had to replace that at a cost of over $400. Last week, the large control board misfired, turning the oven my 16-year old daughter was using to make cupcakes on to clean mode, locking the door, setting the cupcakes on fire, and sending plumes of smoke throughout the house. Luckily, I was home from work with an injury, and thought to flip the circuit breaker. The fire died after about an hour, and the door opened when I put the breaker back on. I just replaced the big control board at a cost of over $500.All told, Ive paid over $2,200 to repair very expensive appliances that are less than 10 years old, and I still have a screaming silent dishwasher. How do you explain this? Planned obsolescence? If so, you certainly have the timing down pat. So why am I writing? I am hoping you will do the right thing by me and in making appliances that last. What is the right thing to do for me? Cut me a check for $2,200? Fix my dishwasher for free? Give me all new appliances and install them? Send me a letter of apology? Im not sure. I will leave that to you. I do hope someone responds. It might be cathartic for me to post a bunch of nasty reviews on the internet, but I hope there is a more constructive alternative.

The oven is a 1 1/2 old, and the enamel is peeling away. I am afraid that KitchenAid is not going to take responsibility in this, and apparently this has happen to other people. What action can I take??

While cooking a roast at 225, which should have taken eight hours, the oven went into the broiler mode at the two-hour mark. If we were not at home, we would have had smoke damage to the interior of the house. The door locked and could not be opened. All controls failed and we had to shut off the breaker. After cooling down for one hour, the door opened and we removed the black pork roast. The oven is still in the broiler mode on high and will not shut off.

I have a brand new Kitchen Aid Conversion Oven/Microwave combo. The way the microwave is designed, you open the door down, like an oven, toward you. Thus, my child opened the microwave, took out some warmed milk, and spilled it on the door as he was getting it out. Some of the milk seeped in between the glass of the door. Apparently, there is no way to clean it! It looks terrible!I called KitchenAid customer service and they told me this a cosmetic issue but a repairman could come and take the door apart for $129 to clean it! Clearly, this is a design flaw! Spills happen all the time with food preparation. The owner should be able to clean it themselves!!! There are no warnings about this in the instruction booklet. How is the consumer supposed to know they cant fully clean the appliance? Why isnt the glass sealed? I want the public to know about the design flaw in the appliance.

I spent $2,300 at Arts Appliances In North Haven, Ct, for a Slide-n electric range and microwave that were shipped direct from the factory. They were so called professionally installed. The time we used them the range emitted a loud pop and a flash which blew the breaker. The cause was a disconnected burner wire that shorted out on the chassis. Evidently the wire was never connected at the factory, an oversight that could have caused a house fire. We also quickly discovered that the lamp in the microwave above the range did not work.Arts sent us a couple of replacement bulbs. It took all my strength and care to remove the bulb which I discovered had been silicone sealed into the bulb socket. Its incredible that no one discovered these defects during the in assembly process or in Quality Control. Two major appliance shipped to the same consumer and both were defective. Adding insult to injury it took days to reach the factory claim center and days for a tech to arrive. The store owners insisted that I had to resolve the problem with the factory.

We bought all KitchenAid appliances when we moved due to their reputation for quality. We didnt get it. The refrigerator has leaked (a recall that we werent notified of) and it marked our hardwood floor. The ice maker quit and now the deli door has broken off. The gas cook top hums all the time and the double oven heats slowly and cools with a noisy fan for a long time. It also snaps and pops when heating and cooling. Our dealer says this is normal. Im writing this so people dont pay extra for KitchenAid quality that is no longer there.

Delivery, installation were excellent. The Stove and oven are high grade, fine make, durable. Great looking design with easy clean access. Wear and tear is nominal. Been over an year and still looks new.

On Monday, January 23rd, 2012, KitchenAid double oven (model number KEBS277SSS04) exploded during its self-clean mode while my 5-year old and I were in the kitchen, showering us with scalding hot glass. Do you know what temperature the glass is when it shoots out of the oven? I called the extended warranty company who tried to deny the claim to fix it. I spent over an hour on the phone just to secure a service appointment. Then I look online and discover that many people are having the same issue with ovens that were purchased about the same time as mine. Consequently, after the oven is repaired it still does not function properly. That is a concern for the safety of my home and my children.Then I contact customer service at KitchenAid. Their response is that they are sorry but Ill have to deal with the extended warranty company. They documented my story and that was it. Clearly there have been other complaints. The lack of response makes the company negligent. Further, they are endangering me, my family and my home if this product that operates at dangerously high temperatures fails or malfunctions again. If KitchenAid as a company are willing to settle with not answering these continued complaints, then you are guilty of being irresponsible with consumer safety.

We have experienced complete failure of our KitchenAid over 5 times. Each failure occurring immediately after a self cleaning cycle. The cycle successfully complete its cleaning. Then the oven will not heat. The problem is the failure of the Oven Overheat Thermal Fuse. Why does the fuse fail but the cleaning cycle completes its job? Most importantly, where is the RECALL? The problem has been reported since 1998 at least! What is the permanent fix?

I purchased my KitchenAid French door fridge (Model # KFCS22EVWH2) new in Jan. of 2012. It is now September 2012 and I have a river flowing out of the bottom of my fridge. I have hardwood floors and the water is destroying them. I called Customer Service and a repairman came today. He explained that he reports this problem every day to KitchenAid. Apparently there is a small hole at the back of the freezer that allows condensation to drip into a pan under the freezer. When that hole becomes plugged, the water does not drain and creates an ice dam. When my kitchen heats up from weather or cooking, the ice melts and flows out of the freezer onto my floor. The only way to fix it is to unplug the fridge, let it defrost for 2 days and then plug it back in. Well, that does not fly with me. My husband and I are handicapped and we cannot go through this process every six months to save our floor. This is ridiculous. I called the company back and was told that this is new to them (right!) and they are sending another repair person in tomorrow. I dont know how this will turn out but I do know that I am not very happy right now. Can I trust the person tomorrow to tell me the truth? If he does get it to work, will the problem return after the warranty is up? Who fixes my floor? In all fairness to KitchenAid, I will post the results of tomorrows visit and a follow-up in a few months. I am in hopes that they will take care of this for me without a problem. I purchased a dishwasher and stove at the same time (also KitchenAid) so I hope that this is isolated and not an across-the-board disaster.

After using the Kitchenaid Smart Oven Plus powered attachments I found the following flaws: 1)Steamer attachment - Steam will escape and cause the oven to shut down. The only way to reset it is to let the steam completely out and turn off your circuit breaker. Kitchenaid did not design the control panel to be steam proof so you cant use this attachment without issues. They do have the ability to do this but wont respond. 2) Grill - You cannot set the attachment beyond a certain temperature so you cant grill like you can on an outside BBQ. 3) Baking Stone - It is difficult to clean if anything gets stuck on it. Again, your temperature for this attachment is limited so you cant bake a good pizza.4) The temperature is lower than indicated, especially in the lower part of the oven. When the oven reports the temperature to be ready, you need to wait an additional 15 minutes for this to take place. Calibration is a joke.

Our KitchenAid gas range have the same problem that many other people have experienced. First, the off button stopped working and the panel had to be replaced. Then when I went to clean the oven, it quit during the cycle. The panel is dead and the door will not open. I will not buy a KitchenAid appliance again. Not happy!

I am very happy with my stove. I have a gas stove and it also has a convection option. The heat seems true to temperature. The convection is a great option when you need to cook in less time. The only drawback is the knobs are not a solid piece and the wrap they put on it seems to be coming off. I use the stove a lot!

We have had our KitchenAid KGRS505X oven for less than 3 years and it has broken down twice. First time only after a month which was under warranty. The 2nd was a couple weeks shy of three years. It is costing us $300 for a one year service warranty so we can get it repaired. Reasonable expectation for an oven of this cost would be 10 years of trouble-free service. So, at this rate I will have purchased this appliance twice in the expected 15 years of service. I cant tell you how much I regret buying this piece of garbage.

On Saturday, the KitchenAid over the stove microwave/convection (model KHHC2090SBL) caught fire before my eyes. Serviceman yesterday said the magnetron had burned holes within the machine and was not replaceable. Unbelievable! Has this product been recalled? What is wrong with this manufacturer allowing this product to be sold?

Well My stove and oven are old. I still have the stove that the pilot lights stay lit. I don’t like that. I have a two year old granddaughter. It worries me because the stove feels hot. I would love to have a new stove. Oh it’s a gas stove.

This fridge was bought at Fergusons in Florida in late 2006 (shipped overseas) and it has been a total disaster from the date of arrival. It is an extremely expensive fridge, over US$6,000. Stainless steel, architecturally designed fridge. Came with NO freon and the ice maker never worked. Took us about 6 months to get the part for the ice maker which the company did pay for the part considering it was a brand new fridge. Since then it has been one repair after another. Every year we are looking at a major repair and to source the parts is a living nightmare. Drops temperature very quickly.Right now it has been working poorly for over close to a year and we have spent about US$1,500 in new parts and still not working properly. Very cheaply made inside, always frosting up, wire baskets in the freezer part are all rusty. Need to try one more repairmen and if he cannot fix it have to throw out a fridge that looks perfectly NEW from the outside. The dishwasher arrived without a handle and we had to argue with Fergusons and KitchenAid to get the handle as if it was an option on the dishwasher. Has never worked properly and was only used about 25 times and just gave up on it.KitchenAid Double wall Oven KEBC208KSS0, worked well until about 18 months ago. Stopped heating properly and cannot find any repairman that can tell me what is wrong. Looks perfectly new from the outside. Note: all these appliances are stainless steel. Bought a food processor the other day 12 qt and it was never working from the start and had to return it. When I returned it found out that many are returned for the same reason. KitchenAid is a pathetic company. They should be ashamed to even call themselves an appliance company. Furnished my entire kitchen with stainless steel KitchenAid appliances and out of the fridge, double wall oven, dishwasher and hob cooker (total about US$10,000), after 7 years ONLY the hob cooker is working (and what can go wrong with that?). Another point, our goods had to be shipped overseas. We are convinced that retail outlets in the USA ship out defective goods especially in Florida where exports to Caribbean and South/Central America are high. Defective merchandise is sent to our region because guess what? Warranties are not applicable when the goods are taken out of the USA. I am happy to send you copies of the bills for all the items and reams of correspondence with Fergusons.Updated on 12/7/2015: I have exhausted all attempts to try and repair a KitchenAid Fridge we purchased at Ferguson Enterprises, Inc, Tamarac, Florida. 24.7 CF Architectural Designed SXS Fridge. Model number#KKSSC42FKS. At the time that we purchased the KitchenAid appliances, we wanted quality products as the items were being shipped to the Caribbean. We thought the KitchenAid brand was considered a quality product. We paid $4,741 for the fridge (excluding shipping and duties and taxes in our country). With all due respect to KitchenAid, the products we purchased appear like quality appliances. All are stainless steel with an excellent finish. That is the dilemma. The fridge looks brand new on the outside, but for the last year it has not been working. It is still in my kitchen as it is built into the kitchen wall and as I already stated it looks perfect from the outside. The big problem is that try as we may, we cannot get the part that is needed for this fridge. I have had 2 parts shipped to me at considerable expense and both are not the right part. Our technician who knows KitchenAid appliances says that we are getting the part for a new model and we need the part for the old model. PART REQUIRED: KitchenAid fridge, Model KSSC42FKSO1. Serial #QM4308660. Power supply board #10155702BO 19/0ct/04. EU 1156 02. These are the numbers that I got off the board. The board goes into a case and the case has written on it: Embraco EU 1556 02B 04. Compressor Electronic Control Unit - UCC2. The first part we purchased was from Angel Appliances. They sent me the part which as we have already said was the wrong part as it is for a new model. It was sent back to them. We have a purchasing agent in Florida who went direct to the KitchenAid factory for the part and it is still the wrong part, actually the same part that I got from Angel Appliances in California. I had a young lady on Skype from KitchenAid parts department the other day and she is the first person to tell me outright that the part I want is no longer manufactured for the old model fridges. She then went on to say that the new part that was sent to us is supposed to fit the fridge that we have. When I explained that the technician says that it does not, she then said that is probably needs some adjustment. When I asked what kind of adjustment? The line went dead. This is a typical trick. As soon as the question gets uncomfortable they hang up on you pleading the line went dead. I did not want to go back but this fridge has been a white elephant right from the start. It arrived in a beautiful crate but when it was unpacked it was not working. It had no Freon. When it started working the ice maker did not work. It took us forever to get the company we bought it from Fergusons to send us a new part for the ice maker at their cost. Then in 2009 we needed an electronic board and had to search for months before we got it from Marcone Supply Appliance, in Miami, Florida. I have had to replace the defrost heater, evaporator motor, all the rubber seal around the doors, only to name a few. This fridge is down continually and I hate to say but the mechanics for the working of the fridge is a terrible quality. Of course, warranties given in the USA fail to work in the Caribbean as the excuse is the appliance has been taken out of the country. So we are left with an appliance that looks perfect but for which we cannot get a part. I love the look of the fridge, its size and its capacity. However, the length of time it takes us to get parts that work and that fit the fridge make it a living nightmare. Yet, why should we have to throw it out? It makes absolutely no sense. Also how can your company justify not making parts for a fridge that is 12 years old? Is there anybody anywhere that can resolve this matter because we absolutely have no idea what to do other than throw the fridge out?

Very Poor Aqua Clean on new Kitchen Aid KSGB900ESS oven. Used the oven to cook a cheesecake. Some loss of liquid resulted in the bottom of the oven. Used the aqua clean 3x, (very poor results). Ran the oven to 500 deg for 2 hours and then Aqua clean 3x. No change in cleaning results. Bar keepers friend used and still not cleaned off. I used all the OEM cleaning scrapers and scrubbers that came with the new oven and the recommended practices in the ops manual, without any luck. It looks like the Aqua clean might be effective on something very soft, but not with normal burnt on material. Submitted a note to KitchenAid service to see what they have to say.

The glass window on my two-week-old KitchenAid Superba double oven with convection exploded last night during the cleaning cycle. Glass flew out all over the floor, clogged the vents of the oven, and terrified me. Thankfully, I was home and able to turn off the unit before anything else happened. Now, I am afraid to replace this with another KitchenAid, especially after seeing these other instances of glass doors shattering.

A KitchenAid KEBS207BSS01 Double Oven came with a new house we purchased. The first time we self-cleaned the oven, the blue porcelain flaked off the convection cover, exposing bare metal. KitchenAid Customer Service stated this was a cosmetic problem not covered by warranty, since the oven was still functioning properly. I replied that the self clean feature was a function that was obviously not designed to chip off the oven interior, and therefore not functioning properly. They suggested a purchase a blue pen from Amazon that could be used to paint over the chipped interior. Incredibly poor product quality and customer service.

The oven sensors dont work properly, and when using double oven, unit shuts down and lower door locks. It seems like many others on this site have had the same problem. It sounds like a class action suit to me as it also appears Kitchenaid does nothing to make it right. When you pay over $2,000 for an oven, you expect a solid 10 to 15 years of use. That is not what is happening. My choices are to pay another $2,000 to $3,000 for a new oven or $500 to $800 for repairs every 4 to 5 years or so. Its not good either way.

I installed a new Kitchen Aid stove in May, 2010. The ovens preheat and self-cleaning features have not been working correctly since I first used the self-cleaning for the first time. I am 85 years old and gave up a perfectly good older GE stove because I could no longer reach the controls on the rear panel and bought this new Kitchen Aid because it has the controls conveniently on the front panel. It was a very bad decision. This is a very expensive junk. If you are considering buying a Kitchen Aid stove, dont do it. I am very unhappy with mine. I recommend you find a good used American-made made product and have it reconditioned by a qualified appliance repair person. I cannot afford this kind of ** product. Now, I do not have a stove that works and cannot afford to buy a new one. I would be happy to be involved in a law suit against Kitchen Aid.

I love my range. The oven is a great size with 3 racks. The broiler takes some getting use too and you cannot have the rack too close. I use the warming drawer every day in the fall and winter. I have 4 gas burners and wish there were 5 but there is a special feature for Woks.

The stove is only two years and old and when the self-cleaning cycle was run for the first time. The thermostat burned out mid-cycle and the unit shut down and the door was locked. The repair cost $213.45. Based on what I have seen online, this is a common problem with KitchenAid stoves. Since it was no longer under warranty, they wouldnt cover the cost. This appliance should be recalled!

I just spent $165 for yet another service call to replace the latch on my KitchenAid range that was purchased in July 2006 from Builders Source in Albuquerque, NM. This makes a total of almost $500 spent on repairs to a range for which we paid $1,346. This was the third call and the second latch for the oven door. The technician noted that the door hinges, replaced in November 2011, need replacing also. The oven door would not shut; it is losing heat and it couldnt maintain temperature and could not extinguish the light. Then, it would not open. All of these are safety and performance issues. There is no response to emails and calls to KitchenAids customer service.” Builders Source offered a discount if I want to buy a new range, but I dont want to shop for major appliances every 5 years. I dont want KitchenAids unsafe, over-priced, and unreliable junk in my house either. In addition to the range, the handle fell off my KitchenAid microwave, the compressor failed on the refrigerator, and the latch, springs, and door failed on the dishwasher. There was a time when an appliance’s longevity and dependability relied on being well-made, and buyers weren’t saddled with purchasing extended warranties. Until retailers like Builders Source insist that manufacturers stand behind serviceable appliances, consumers will be deluded and disappointed with shoddy merchandise and choosing between which brands will provide the least trouble and expense. I expect that KitchenAid will continue manufacturing unsafe, overrated products and unresponsive, uncaring service until their once-respected reputation and the retailers that push these shoddy products disappear.

I had a new kitchen put into my 80-year-old house by a reputable, long-established DC firm. The kitchen itself is a delight, and I couldnt be more pleased. Because of the somewhat unusual footprint of the space, we were limited in our refrigerator options. I chose a stainless-steel Fisher-Paykel fridge and I love it; I had my own GE Profile range reinstalled. That left the dishwasher and the microwave. Kitchen Guild (the company that installed my kitchen) said I could get a deal by buying at least two KitchenAid appliances. I had never owned a KitchenAid product, but I thought they had a good reputation. What a mistake!The dishwasher started having problems with the LED display before the end of the first year. Finally, it froze completely, and I have not used it in over two years (the kitchen was installed 6 years ago). The built-in microwave with vent fan also began having problems almost immediately. First, the grid on the top fell off and broke; I called and they sent me a new one. Then, the handle fell off and they would not do anything about it! I super-glued it back on. Then, the replacement grid fell off; I super-glued that back on. Tonight I was preparing dinner and put some veggies in the microwave to heat up. The oven started making very loud, strange noises and then I smelled a strange, electrical smell. Obviously, there is something seriously wrong with the oven, and I cannot use it again. I now think I was offered a good package rate on these appliances because they were clearly lemons! I have never had such a negative consumer experience in my life! And I thought this was supposed to be a premium brand! Has anyone else had a similar experience with KitchenAid products? I paid a pretty penny for them and this is an outrage.

I read a post where someone said their KitchenAid fridge had finally broken down after 15 years and that it served her well. Major appliances used to last decades, and still should last that long. Think about how much you pay for them 15 years is nothing. Our fridge has a pull down bin in the door that pops open every time we open the door. Even with nothing inside, rendering the space useless. Plus, the bottom of the freezer pools with water which then turns to ice making it impossible to close the freezer door. So far I have had to unplug it and thaw it out five times. If that sounds like nothing, remember you have to put all your groceries somewhere. Tonight instead of enjoying the beautiful summer evening, I made many trips up and down the basement stairs bringing groceries back into the fridge.My oven is also a mess. The knobs get so hot that my friend burned her arm on them. I cant imagine how this passed inspection. NOT SAFE if a toddler was around. Thats okay because she was in the middle of a remodel and was considering my oven until that happened, and I filled her in on the rest. Also, the back panel on the stove is made of resin! I thought it was stainless in the store. So needless to say it is peeling. I guess that is the reason they had the stupid idea to put the smaller burners in the back and the mega burners in front. So much fun trying to reach over a large pot of boiling water to stir a small saucepan in back. Does KitchenAid have third graders designing their appliances??? Clearly not someone who has any knowledge of a cooks needs. I will never purchase anything by KitchenAid ever again. Not even a can opener.

I bought KitchenAid refrigerator, dishwasher, and range 2009. About two months ago, the ice maker would not dump ice into container. I had the ice maker serviced with 2 circuit boards on three occasions, still no ice. I had the ice maker replaced last week. It dumped two trays of ice in the next three hours. None since. Called factory service, and was told it MIGHT be the motherboard, at a cost in excess of $200 more. I have already spent in excess of $600 in repairs. My extended family of more than 100 people will NEVER purchase another KitchenAid appliance again.

I have had this Electric range KSEG950E for about 2 years and have had major problems with its self-cleaning technology. For starters, it simply doesnt work, even after repeated cycles. Cleaning out the water after the cycle is finished is tiresome. And the side and back panels never come clean. Its nearly impossible to scrub out these areas, as you can only use nonabrasive pads, and the oven is so deep, you cant reach in far enough to clean effectively. Even soil on the reachable areas is a challenge to clean, using only the recommended non-scratch scrubbing sponges and fresh kitchen appliance cleaner (the addition of which is recommended for hard to remove soil).Im not a heavy oven user and have tried to clean oven at the slightest sign of soil build-up. Once more, being 5 7, Id think that reaching around inside the oven to scrub should be easy. But after the lengthy clean-up sessions, I hardly need to go to the gym for exercise! Surfing the net, I see that Im not the only very dissatisfied customer! It may be good publicity to have low-energy cleaning technology. But if it doesnt work well, it cant earn high marks for the company.

We have had this range for 6 years. If you check the service calls, 3 have been for the oven not reaching maximum temperature. Each service call is close to or more than $200.00. The temperature works for a while and then returns to 259 degrees. Never been fixed properly. Now we have an error F2E1, service call $125.00. The repairman said we have an error F2E1 and we would have to order a new keyboard. Really $125.00 to tell us what we already knew. Now, to make matters worse he said this part, estimated cost $500.00, may not correct the problem and further work/parts would be needed and he wouldnt know until he tried the new part. The most frustrating part is he said the keyboard part could not be returned if further work was necessary thus increasing the price and that couldnt be determined until he started the work! So, we have decided to buy a new gas range and a new fridge and obviously neither one will be a KitchenAid.

KITCHEN AID IS JUST A NAME BUT THE PRODUCTS ARE GARBAGE, GARBAGE, GARBAGE. My wife bought stainless steel appliances from KitchenAid and they are all lemons. KitchenAid stove panel was changed 4 times under warranty and 2 times after that out of pocket. (KitchenAid is total Garbage.) KitchenAid oven STOP working after the FIRST self cleaning; cost me $89.00 to diagnose and 200 to repair....... Again, what garbage these people sell. KitchenAid fridge ice maker STOP working, need to fix. KitchenAid microwave handle fall off after 3 years of use. The thing that bothers me the most is that you get absolutely NO support from KitchenAid if you call them. What a ruthless company taking advantage of so many consumers.

The food does not get very hot regardless of temperature set. It gets warm or warmer. Prefer my toast oven if the dinner is not large. This little oven cooks faster and HOT. Customer Service was UNHELPFUL and rude. Oven is OVERPRICED and low quality.

I have had my KitchenAid slide in range for 3 years, model KGRS807SSS00. Ive had the panel burn out twice while cleaning the oven. Repairman said that this happens quite often due to the fact that the oven heats up so high that it burns out the panel. This seems like a defect with the appliance yet KitchenAid refuses to believe it is their problem and wont repair it. Last time I will ever buy a KitchenAid.

I recently bought a KitchenAid oven (KGRS206XBL2). In the first 4 weeks, all the markings on the burner knobs were wiped off. I called KitchenAid who responded the warranty does not cover the knobs. After much discussion, their response was basically we dont care. Poor products and terrible customer service.

I had this KitchenAid stovetop for 13 years KDRP407HSS4. Suddenly, without warning the broiler went on. I turned off the electricity at the fuse box. I turned it back on and this time the clean cycle went on while the knob was in the reset position. It created a fire. I was there to put it out. This is scary when a stove can turn itself on without a person doing it. If anyone else had this issue, please reply. I see some people had explosions. If you have a KitchenAid I would make sure it does not start on its own.

In my quest to contact Whirlpool (US), with perseverance, creativity, luck and detective work I received a telephone call from Whirlpool (U.S.) shortly after my initial review. A Whirlpool Executive (Mr. Chastain) was apologetic and took control and personal responsibility of my problem. Mr. Chastain arranged for a technician to service my microwave to my satisfaction and provided me with a full refund for all Whirlpool service charges (parts and labour). While I am grateful to Mr. Chastain for resolving my problem, it would be helpful if Whirlpool included direct telephone #s (not a call center) and legit email addresses on their website for consumer SOS.

Kitchenaid Duel Fuel Range Oven Problem Model KDRP407HSS10 - While baking oven door locked and went into cleaning cycle, food in oven was smoking and could not cancel cycle. Husband had to turn breaker off and let oven cool down and then turn breaker back on so electronics would unlock door and then was able to get food out. Tried to use oven again and did the same thing. Called Kitchenaid and they would not admit or even acknowledge they were aware of the problem. I told them they had to be aware of the problem because I have seen postings of the same exact problem going all the way back to 2005. Had to ask twice to talk to supervisors at next level to try and get their explanation of what it would take to repair the range. I explained I wanted to talk to someone who had knowledge of what it was required to fix the problem. Someone at KA has to know what is wrong. I am now waiting for the third supervisor to call us back. One posting I read said that in the state of NY there was a class action lawsuit filed against KA. This is an extremely dangerous situation and could cause a serious fire. Do not understand why this problem has not been addressed. The ovens should have been recalled.