This is a very nice brand of microwaves. Has easy touch from 30 sec to 10 mins. Meaning you touch start for the 30 sec and press 1 for one min - just hit start after. The only bad thing is the plastic coating over the buttons is starting to rip. Not a big deal just doesn’t look as nice.

SOLVED: PDW9980L00SS GE Profile Dishwasher not cleaning dishes. The rubberized sump of this dishwasher suffers from chemical deterioration. In our case the deterioration allowed waste water to bypass a check valve and return into the wash water. Dishes dont come out clean and the spray wands get plugged up with bits of waste. The solution is to replace the sump. If youre handy with tools its an easy DIY job which requires pulling out the dishwasher and turning it on its side for access to the sump. Lots of videos online re the process and for safety start by shutting off the circuit breaker for the dishwasher power. For our model the new sump part number WG01L00289 replaces the original WD18X10026. Dishes & glasses now sparkle. Hope this helps as there was lots of frustration on this end before replacing the sump seen in the photo.

GE Profile Microwave JVM1850DMCC - For the third time in 5.5 years, Ive experienced a magnetron failure in a GE Profile Microwave. The first failure was fixed under warranty. The second was so bad, the microwave had to be replaced, but it was no longer under warranty. I should have heeded the warning and gone to another brand, but on 12/31/10, I paid over $500 to replace the microwave with a new GE Profile to match the existing appliances. Apparently this was a big mistake as the magnetron has failed yet again. The microwave is on its own separate 20A circuit, so that shouldnt be an issue. It would seem, however, based on the number of complaints I see on this site, there is something inherently wrong with the manufacture of these microwaves, or more specifically the magnetrons. Im extremely disgusted at this point.

I purchased a GE Profile Microwave 2 1/2 years ago and now it is shooting sparks out the back and making a loud noise. I have to admit that the microwave did work well and my mom even bought the same one because it was good. I never bought a GE appliance before because I was told they have a bad reputation. I thought the Profile Series would be better. Wrong!

I thought there were food particles between the glass plate and the ring. When I took out the plate, I saw that the paint had bubbled and was peeling off the bottom of the microwave. Extremely unhappy with this. Ive had hand-me-down off brand microwaves that lasted much long than this GE and with NO PROBLEMS until they just rolled over and died. I have all GE appliances in my kitchen and have to say that Ill never buy GE again. Electric stove is a problem, dishwasher a problem. Refrigerator was a problem (when it was new! it was fixed and thankfully is still running well).

This is the second GE microwave. In 2 years I have had that, the paint peeled off inside the microwave in sheets! I contacted GE the first time and was offered no help or explanation. I was told it was an older model, even though I bought it new. This time, I just chose to throw it away and never purchase another GE appliance again!

Front of door never seems to clean up well and its stainless steel. Occasionally if you use the start delay and a harder pod it can stick and not dispense fully during wash leaving a chunk of it. I love the ability to run half loads. Smartly designed, and easy to use.

The microwave is large enough for a whole chicken and operates at both a high speed and good efficiency. Most items can be timed within minutes of properly prepared meals.

I bought a Moffat washer and dryer, and the timer came out of place and burnt on the inside. The timer clips in and if push too hard it will fall out or break the clip. We have extended warranty on it and due the repairman came out twice. The warranty person said it cost more for the repairman than the dryer worth - theres no more warranty. I think the dryer should replace when the timer fell out of place. This dryer should be called back.

GE Model PDW9280J10SS Fire - Many GE Profile dishwashers have been recalled during the same time frame as the model we purchased, but it is not listed as one of the recall models. Just as many other complaints, ours started to smoke out of the top of the front door and filled our house with smoke. Thank God we were there to shut it off. The next day I opened up the front door to see what had been burning and it had holes burnt in front and back of the main circuit box (for lack of better name), one burn mark right where the main wire harness plugs in and burnt right through it. This is the same description many others have written. There is a problem with all of these Profile dishwashers purchased between 2006 and 2009 (ours 2007). If we had not been home, who knows what would have happened?

We moved into a new home in June of 2011 with the appliances already included. Ours came equipped with a GE, over-the-range microwave, model JVM1540DP1WW, manufactured in Malaysia, in April of 2010. Within several months, the revolving platter began to make a bumping noise while turning and then it eventually quit turning altogether. Five service calls later, we had the platter motor replaced, circuit board and four fan motors (apparently the platter has voltage supplied from that fan to make it run) and it still didnt work.It was taken back to the shop and eventually the problem was traced to a loose wire on a terminal connector. After a month of operation, it is again beginning to make the bumping noise while the platter turns. To top it off, Consumer Reports (the March issue) deals with problematic microwaves, especially the GE model and the unexpected fires that can occur. In addition, they can be susceptible to (not always however and only on certain models) wireless transmissions which could potentially cause them to start on their own. I know for a fact that it knocks off my XM Satellite Radio when it is running. Bottom line...its history and will be replaced with a check rated appliance before I too have a major problem.

In January 2013, my husband and I purchased new appliances from Home Depot, including the above referenced dishwasher. The first dishwasher was delivered broken. The display panel was detached from the body of the dishwasher. At that point, I was concerned about the quality of the product. From the way it was detached, it appeared to be very cheaply made. (It was also installed incorrectly, causing a leak under our sink and ruining the bottom of our cabinetry. We settled this with Home Depot, but I include this detail to help emphasize my frustration over this whole situation.)When I contacted Home Depot about the faulty product, they agreed to provide a replacement, so I decided to give it another try. I wish now that I had simply returned the product and purchased another brand. Upon receiving the new dishwasher, I noticed immediately that the edge of the inner rack was scratched so badly that the plastic coating was gone, and rust had already begun to appear. I had to call customer service and get replacement racks. (More on this to follow.) Allow me to detail our service call records:Call #1. Heat dry didnt work at all. The technician told me that I needed to run the water in the sink and make sure it was very hot before running the dishwasher, and he changed the settings. This created a slight improvement, but not much.Call #2. Soon after, detergent tabs started to get stuck in the dispenser cups. I was using the exact brand recommended in the manual. The technician told me that detergent tabs were just the worst, and that I should try gel detergent, even though this is contrary to what the manual states. The detergent ruined my silverware, and I have had to purchase a new set, which I now hand wash.Call #3. Using gel detergent did not work. Technician came back, and told me the wrong replacement racks were sent. That must be what was blocking the water from getting to the soap. He ordered another replacement rack. He brought a plastic door, watched the water, and told me the upper arm wasnt spinning fast enough. He made an adjustment and claimed to fix that.Call #4. Detergent still not emptying from the cup. A different technician came back and used the plastic door. He found a different problem, but did not have the parts to fix it, so, another service call had to be scheduled.Call #5. Technician comes back, and finally fixes the detergent cup problem. For now.Call #6. Heat dry now does not work at all. There is so much water on the dishes that I have to hand dry them, and afterward, I have to mop my floor. There is just a massive amount of water in the dishwasher. In addition, it will not start except on a one-hour delay. Pushing the delay button does nothing to change the settings, and does not allow me to scroll through like it should. This appointment is scheduled for today, but I am not hopeful that anything will change.At this point, I have no faith that this dishwasher will ever work. Customer service did extend my warranty for six months, but that is the only concession I have gotten from them. That extension will expire soon, and I fear that at that point I will simply have to spend another $600 on a new dishwasher and leave this one on the curb. Its unacceptable for any consumer to have to purchase a new dishwasher less than two years after purchasing from GE.

I cant remember the exact date of purchase for my GE Spacemaker microwave oven. I have a receipt somewhere, but I have receipts for repair dated 2002. It is for a door seal gasket for the microwave. A model JVM60 GE Spacemaker installed over the range.The microwave worked perfectly for several years. Then one day, when I pressed the start button, I noticed a small fire inside the window above the control panel where the time is displayed. I called repair man; I was told that it was the circuit board, and GE was not able to send repair spare part. Since then the microwave is only good for displaying the time, and storing my everyday pan. I do remember paying $400.00 for this microwave because I purchased it at my employment. It would seem to me a company making a $400.00 appliance would be backed by a circuit board, which they know would go bad in a short time. Thats why they only had a one year warranty guarantee.To show you the difference in a microwave appliance, I purchased a small counter top microwave in 1997; it still works like a charm, and I use it every day. From the negative reviews I read on these Spacemaker microwaves, I firmly believe there should be some compensation to us consumers for the money spent, plus the hazards we experienced. If that is not agreed, then all of us consumers should file a class action suit against GE.

I bought GE OTR microwave in December. It is exactly one month old now. My model no. is: 9195SVC. It looks good, but I find the fan very noisy, even when it is at low. My range hood which we had in the kitchen prior to this microwave was very quiet at low and only a bit noisy at high. I do not know if the noise is because I have steel exhaust pipes vented out. Rest is O.K. but given that others have reported problems in 1-2 months, I am still nervous.I bought this product at Sears with an extended warranty, which is some relief. However, when I was shopping for this at Home Depot, the salesperson told me these microwaves last only 4-5 years. One good thing about Sears extended warranty is that if it is not used over the five years, they refund the warranty payment (with taxes) in the form of a gift card and they were also cheaper than Home Depot.

My less than a year old GE microwave stopped working last week. My AT&T phone service died so I had to make repair arrangements online. Guy was here this morning. My microwave’s main board is fried. It does not conform to Repair Guy’s published schematics. Repair Tech could not upload new data to it. Repair guy did order three new parts including a main board. GE told Repair Guy that mainboard delivery ETA UNKNOWN. After three hours here repair tech left and told me to call GE customer care. Believe it or not, two hours on telephone with GE. First you need to talk to a customer service rep that cannot help you. They then determine you need a Customer Advocate. Then they need to input data on your file for the Customer Advocate.Then they need to transfer you to that department. Then you have to get a case number assigned. Then you give someone all the serial numbers and model numbers again. Then the Customer Advocate (CA) takes the call. The CA does not speak English as you and I speak English. After the CA puts me on hold to verify the purchase, then the appointment, then the tech and then the order they actually speak to me. In my case, the mainboard part is not available on CA’s computer. The CA has to electronically contact the parts department to find out if the part is in this universe. If the part can be delivered to my Repair Guy in Jackson, GA within 14 BUSINESS days from the date of the inquiry I have to take the part and wait for repair.In the event the part cannot be delivered in 14 days CA will start a process to get me a new microwave. The parts department has up to 48 hours to respond to the CA. When asked what happens if no response occurs in 48 hours, I was told, That never happens. It is the Christmas Holiday and I anticipated guests. My husband is disabled and his meals are pre-made frozen so I will have to decompose them and heat them on the cooktop. GE could care less about those issues. So after waiting five days for repair I have no working microwave. Someone told me not to replace my GE with a GE, but I did not listen. It is December, holidays, no microwave is an aggravation that I thought paying for a GE product would alleviate. So, on January 2nd I might get an answer. Part possible or new appliance COULD be ordered and delivered by someone sometime.

Our GE microwave is used primarily for heating things though sometimes something is actually cooked in it. It is a useful tool and saves time and labor. I would rather have one than not.

We purchased our Adora over-the-stove microwave oven from Home Depot. The Adora brand is made exclusively for Home Depot and were sold on its special functions and value. Well now, 3 years later, this exclusive models glass fogs up when we use it. There are only 2 of us living at home. We use it maybe 4 or 5 times a day. A microwaves typical lifetime is 9 to 10 years. Also, by the way, when we turn on the fan to highest, it sounds like an express train hurtling through our kitchen. Our dog had a heart attack and died the first day we operated it. No he didnt. We dont even have a dog. But you get the picture.

Have had my GE dishwasher for 15 years. Had initial problem with inner liner pulling away but got GE to replace unit. Has worked fine ever since. Nothing fancy just gets the dishes clean. Would have liked a bit more adjustability with the shelves.

My experience with GE over range microwave oven as follows/ Unit Mod.JVM3160DF3WWW. Ser.#GH260692A, this unit was purchased April 2017, February 2019, unit began to disconnect itself during normal use. This was done by way of throwing 15 amp breaker. No satisfaction from GE, NO extended warranty purchased, guilty as charged, contacted elect. tech. No idea of problem, #2 elect. problem in door sensors of which there are numerous, notice black residue on duel latch on door caused by door latch device rubbing on unit latch receiver cost to discover which sensor cause and replace one or all 250.00.We have been limping along for two months with frequent trips to basement resetting breaker (which we had replaced) next move, purchase NEW MICROWAVE. Let me be very direct if we wanted JUNK we would buy Asian made, THAT being said, there will be NO...General Electric products in this house. This is our second GE product BUST, 100.00 advertised by manufacturer. Never delivered! But hey we are just small time consumers. What might else we expect.

It is functional and does the work. We are impressed with the large drum which takes a good load. It runs smoothly but with some noise. However we do not mind this as the end product is what we wanted.

I replaced a GE JEM25 microwave when the Magnetron gave up with a PEM31DWW unit. Within 14 months the paint on the ceiling of the oven started flaking off. Contacted GE and they offered to sell me another oven for $166. After reading all the negative reviews on this site, I dont think I will ever buy another GE product.

I purchased my GE Microwave about a year and a half ago. It has served me with flying colors till yesterday. To explain, I was boiling a small plastic pan of water for some rice. I have done this many times in the past. In the middle of the cooking cycle I heard a loud bang from the microwave. I stopped the cooking cycle and opened the door. To my surprise the glass turntable had shattered into several pieces. I cleaned out all the broken glass and tested the microwave. It seems to be working perfectly with the exception of the glass turntable. A new one was ordered. No further action is required. This is just an information for GE.

Dishes on top shelf do not get clean, and Power Dry does not dry dishes. Technicians say nothing is wrong with the unit and customer service was a nightmare.

I also have a GE Profile dishwasher with malfunctioning wheels. I read this site, and was comforted and enraged that I was not alone with my melting wheels. I sent GE customer service a note, explaining my problem. I also included a link to this site in my note. I explained that I was a loyal GE customer and that they should stand behind their products although my unit was no longer covered under warranty and did not qualify for the recall. GE responded to my e-mail with in 12 hours. They sent me a complete set of new wheels for my bottom rack free of charge, and sent out a technician to install them, again free of charge. They also e-mailed me to make sure I was happy and no longer had concerns. I am thrilled with my experience. Let me say that again I e-mailed GE and within 8 days (a holiday included), I had new wheels and a technician to install them at no charge.

I know this commonplace complaint, like thousands before me, will head straight into the wind because the world just works in this way: technical support and repairs works as a profit center for a corporation. My GE Profile microwave abruptly failed out of warranty after years of use. The cause was due to a wire burning up inside that had not been loosely connected, said the GE technician, so this was an issue of inadequate quality--not bad enough to cause the microwave to fail quickly but enough to cause failure over time.After taking the microwave out of the built-in cabinet, it only took the technician about 5-8 seconds to find and diagnose the problem, several minutes to get the right part (a wire) from the truck, and a couple of minutes to fix it. The labor charge was $121 for about 7 minutes of repair work, to be liberal with time. (This charge is separate from the charge to come to our home and diagnose the problem.) This prorates to over $1,000/hour for a basic wiring change, which I think is exorbitant. I understand that the technician is a highly trained individual, but this is already reflected in the high labor rate.According to GE, the cost to replace the built-in microwave, which came with a matching stainless steel frame would be $550 if we wanted the new microwave to match the frame at least (but not necessarily the oven, stove, etc.). This is the kind of cost you dont think about when you buy a new home built with matching appliances--well, I didnt. Companies like GE can rationalize all they want about all the overhead associated with servicing a repair call. I can certainly grant them some leeway, but in the end, charging an extra 8 times more an already high labor rate given the time needed to fix the problem is simply price gouging a consumer who has no good recourse. (This is why I pretty much avoid repairing anything, except for my car. Its almost never worth it.)I recently had an experience with an experienced plumber charging an hourly rate of $150, prorated by and rounded up to half-hour increments of work, regardless of difficulty of work. Repairing an appliance should work the same way, and my GE bill would have been halved. Because of such profiteering, I will not consider purchasing a GE appliance in the future. I pray that this microwave doesnt break down again in the coming years due to some other problem. It would be a lot less expensive to just buy a non-matching portable microwave then for $100-$150 than to keep up appearances.To be fair, the woman who fielded my service call was courteous and empathetic. Because the microwave apparently had an electrical burning problem, she previously waived the diagnosis fee. Otherwise, my simple repair would have run several hundred dollars, more than the cost of the microwave. However, she was unwilling to reduce the labor charge, so based on how strongly I felt ripped off, I give GE a star rating overall.

We bought the GE Potscrubber in 1997. It’s still going strong and our dishes and serving platters come out spotless. We did have to replace an inner seal once, but the part was easy to find and inexpensive, and my husband was able to put it in himself by following instructions on YouTube. We bought this before the stainless look became big but the shiny black exterior looks fine next to our new black stainless stove.

My GE Dishwasher is disintegrating. Its three years old and we didnt live here for a year of that time. The door where all the electronics just fell apart. I bought the most expensive GE Dishwasher I could find at that time because we wanted one that was quiet due to the way our house is laid out. We were able to put the door together again but the strip across the top never fit again so we taped it on. Model PDT750SSF1SS. The controls wont work.

Ive used this GE model JES2051DN1BB (manufacturer date August 2008) microwave for ten years now and impressed that it is still working perfectly cause you dont see that much anymore. I usually prefer Maytag products cause my GE washer and dryer did not last for me, but this has seem to be different. Maybe GE should stick to making microwave ovens instead of anything else.

GE Model WES1130DM2BB MFG APRIL 2011, bought Oct 2011 @ SAMs Club. Microwave continues to run after cook time and will not stop until unplugged! Service Dept offers a $25 discount on a new GE Microwave after cutting cord & sending info plate in. I am concerned this microwave will cause a fire! Luckily I was near and unplugged it!

Our new GE dishwasher is a disappointment. 1. There is water on the door after the dishes wash. 2. There is soap on the door after the dishes wash. 3. The silverware is often dirty after the dishes wash.I have observed the following: 1. The reason for the water is the silverware trays are made of plastic and do not dry. They should make them of coated wire like they used to. 2. The soap tray is often prevented from opening all the way by the silverware in the rack. They should re-design the bottom rack. 3. The silverware tray is too enclosed for good cleaning. It should be made of coated wire like they used to.

I purchased a stainless steel GE dishwasher for $508.68 since I remodeled my kitchen October 2016, I contacted GE in March 2017 because the stainless steel on the dishwasher door started to have rust spots, they sent a technician to look at it, they told me that they cannot replace it because the aesthetic warranty is only good for 30 days. They authorized the technician to replace the door, however I have the same issue with the new door, and also the dishwasher stopped working. I contacted them again. The technician was able to fix the dishwasher, but as far as the stains on the door they told me thats an aesthetic issue. They cant do anything about it. I called the consumer relations department. I spoke with CIARA GE case # **. They offered me a small discount and I have to come up with $400.00 to buy a new dishwasher.I feel that a good business should always stand behind its products. The dishwasher obviously is defective, they sold me an appliance that supposed to be stainless steel but its something else, the right thing for GE to do is to exchange the defective product for the right one. I am very frustrated that in less than a year I have to spend over $900.00 for a dishwasher. I am great customer for GE, I remodeled my kitchen, I purchased a GE refrigerator, cooktop, oven, kitchen hood, microwave and dishwasher, I think I deserve better than a small discount for a defective product.

The key pad says it is shorted out and needs service. It turns on randomly. I unplug it and plug it back in and it will either say service needed, keypad shorted out’ or press clock .I dont use it much for microwave cooking. It came with the house we just bought and it only worked for 3 weeks before it started this mess. I could deal with it if it didnt beep all the time.

A small black piece of plastic, which snapped into the back of the microwave handle has bent/shrunk, and popped off. My microwave is just a little over one year old. I called the GE 1-800 phone number for parts, and GE does not offer a replacement part for this, without buying a whole new replacement handle, which costs over $160.00.

Our microwave is spacious, simple to use and dependable. This is about the fifth microwave I have had. The others only lasted about 6 months. My current microwave is about 5 years old, despite the fact that some of my previous ones were also GE.

I bought GE Profile dishwasher (PDT750SSFSS) from Home Depot on Sept 2014. First week it had some drying issue and GE service technician told no issue with dishwasher. After 4 months, electronic control board stopped working and GE service technician replaced the board. It worked for about a month and again same control electronic board failed and need to be replaced by GE technician. Again within a week again board failed for 3rd time. This time I asked for a replacement from GE since same board failed 3 times but GE refused to replace and told they can only repair and cannot give a replacement of dishwasher. Again for 4th time same control board failed now and I have contacted Home Depot for help. I dont know what to do this time and I dont want to repair this dishwasher anymore. It is only June 2015 and it had been repaired for more than 4 times. Ill try through Home Depot to get a replacement, if not Im planning to go through consumer court and file case against GE Profile. I would appreciate if somebody can help in resolving this issue and you can contact me through my email.

Our GE microwave, manufactured in 2012, has been running fine, but the door handle has cracked on the bottom. Imagine my shock when I found the cheapest price for a PLASTIC handle was well over $100. How can this be?

We have a GE SpaceMaker JVM 239BV 001 over the range microwave purchased about 10 years ago. Within one year of installation the handle snapped - just as numerous people here have stated. I went to our local replacement parts store and was shocked that it cost $30 for a new handle. The sales person said if I were you I would by the lifetime warranty for an extra $3 because you will be back, I sell lots of these.

GLD6560L00SS. My dishwasher (Model number:GLD6560L00SS) was producing large amounts of smoke through the face panel. It filled my kitchen with smoke and produced a strong smell. I contacted GE and they sent a service repairman out and he took a look. He said this problem is very uncommon with this specific unit and he has never seen something like this. After he removed the front panel, we were welcomed by a burnt/charcoal black face-plate. There was an internal fire in the machine. To fast forward I have been working with GE the last 3 weeks and they have offered to cover 50% off a new unit. I cannot afford this even with a discount and they will not cover the cost of a replacement. This problem could have been much worse if I was not home. The house very well could have started on fire. We normally set the unit at night and go to bed... Thank god this was a different day. This kind of thing is unexceptionable and the fact that they will not cover.

Our GE Microwave Oven/Convection Oven Combo (Model: PT970SRSS) is a little over 2 years old. The interior paint on the ceiling of the microwave oven is chipping and bare metal is exposed. In addition, the microwaves glass turntable frequently slips off its plastic tripod base. Circular scratch marks, which also expose the underlying metal are evident in the area which is located directly below the glass turntable. The circular scratches are a direct result of the glass turntable scraping against the paint. The GE repairman said chipped paint is not repairable and that paint should not ever chip in a microwave, let alone a relatively new microwave. After many calls back and forth to the GE Consumer Relations person, we were offered a new combo at a discounted rate of approximately $1,000. (We paid around $2,000 originally.) Im not satisfied with this offer. I strongly feel that consumers should NOT have to pay to replace a defective item. GE needs to pull these defective and dangerous products off the market! Take a lesson from GM!!!

I love the GE. I bought a GE dual fuel range about 3 years ago when my 6 yr old Frigidaire stove caught fire. Always wanted to cook with gas but have electric oven and broiler. It's also easy to clean the cooktop unlike older gas stoves. Love the big fast boiler eye.

This dishwasher was in the home we bought and its just not a good one at all. We dont like the settings.. We dont like the size. Weve seen better settings on other dishwashers when shopping around and pricing for a better one.

I purchased a GE over-the-range microwave, GE Profile **, on 2/22/2005 as part of a kitchen renovation. I also purchased the GE Profile dual-fuel range, **, and the Profile ** refrigerator at the same time.I am now having to replace the over-the-range microwave as the interior enamel is chipping off in chunks rather than the discreet amounts in the beginning. The dual fuel range burst into flames and was replaced 3 years ago (the line was eventually recalled). The tracks that support the drawers in the refrigerator are breaking off slowly but surely, meaning they will not be useable shortly. I would not take a GE appliance as a gift.

Had 2 G.E. microwaves make a loud popping sound (like a boom) while turned off and then they started smoking like crazy. 1 model #JVM1630BB004/ serial#MA9713685. The previous microwave was just thrown away. I didnt realize there was a problem with these G.E. microwaves, so I dont have the other model/serial #s. These are a real danger.

Ever since I bought this dishwasher in Jan 2014 it hasnt dried properly. Finally had a tech come out and he told me the water wasnt hot enough. How is it energy efficient if I have to raise the heat in my water heater to get the dishes to dry???? Very dissatisfied! My old dishwasher (with plastic lining) dried the dishes with no problem. I had it for 16 years before I had any problems with it. This new one is a problem from the first time I used it. No GE ever again!

Purchased the cafe dishwasher in March. We are now on our second one as the first did not work and now this one does not work. It worked fine for the first couple of months and now it’s doing the same thing as the first one. Pump is on the fritz apparently. Truly disappointed. We owned the cafe dishwasher at our last house and loved it so we made sure that we purchased the same one when we bought our new house.

When the handle on my expensive replacement (GE Profile for GE Profile) microwave/convection oven peeled, we called our retailer (PC Richards is really good about service). A new door showed up and it, too, has a plastic handle. The difference is, this time its solid grey plastic as opposed to white plastic with silver paint. Seems to me that an expensive SS appliance should have an SS handle. Too heavy? Just use a tube of SS - not solid. Too hot if above burners? Didnt my last GE Profile micro/convection have a SS handle? I spoke with customer relations. The person was well trained not to say anything that might suggest she agreed with me. Since the issue is cosmetic and not functional, I have to consider the issue dealt with now that the door has been replaced. I told them I will do my best to publicize this issue and that I will never again purchase a GE appliance. I also called CEO Jeff Immelts office in Connecticut. I made it clear that my dissatisfaction has cost them a long time, loyal customer and that I would spread the word. I would appreciate if anyone agrees with GE that a SS handle would be too hot over stove burners.

I loaded and ran the GE Profile dishwasher in the evening. Later that evening, putrid odor of undetermined origin was noted in the house. I searched throughout house to find the cause, but it was not located. The next morning, the dishwasher was found to be extremely hot on the outer surface (door) and countertop. The heated dry light was on along with the start button, which would not reset or turn off. The unit had to be disconnected by turning the electrical breaker off. All contents were either melted or had a strange brown film, along with broken tines and melted silverware rack in the dishwasher. Even the water dispenser in the bottom of the dishwasher was melted or broken. A GE service representative was called and his report stated: Unit was left on for too long and heat caused excessive damage to the product. Due to excessive damage, unit is non-repairable. He shared with me he had never seen this much damage done to a dishwasher. I spoke to GE consumer advocates twice and their solution is to provide me a discounted price on a new appliance and the email address for formal complaints. When I inquired about if there had been resolution to the cause of this problem because I wanted to make a formal complaint, I was told there is not a safety issue with the heating unit. I then spoke to a GE resource person in recall and she shared with me that it is a known issue of overheating and destroying contents, but it has not caused a fire. Igniting a fire is a justification for a recall - can we not be proactive? This department is working with me and ensured that in newer models this potential hazard does not exist. But other consumers who have purchased in this model (PDW9280N20SS) should be aware of the potential fire hazard. Everything was very hot inside and out. Consequences: the 3-year-old dishwasher (that I use about once per week) was totally ruined and I inhaled potentially toxic fumes for over 8 hours.

The microwave is over the stove with a vent. It is about an 1100 w microwave. I just have to eat out a little bit more time here are the ones that are bigger. The price was right there and that I would’ve bought something else.

Bought the unit about 2 years ago. The interior paint started coming off after about 1 year and several months. At 2 years, the unit stopped working and is reporting a shorted keyboard. I have had other over-the-counter microwaves that lasted over 12 years and were replaced just due to old age and style. I have read about others with the exact same issues. Ill stay away from GE products big time after this display of poor reliability.

About a year and a half ago, I bought a GE Profile dishwasher from a very reputable local dealer. Within 3 months, the digital control panel failed. Because it was still under warranty, the dealer replaced the panel. It failed again. This time they made other adjustments, it continued to fail. Finally GE suggested that the dealer replace the entire door panel, which they did. It took the repairman a couple of hours to do so. Still didnt work. Finally GE declared the machine non repairable and replaced it. Unfortunately the men who replaced the dishwasher didnt install quite correctly because it leaks. I keep a plastic container under the front left corner to collect the water every time the dishwasher runs.But the story doesnt end there. This machine and the first one both include a sensor that apparently check for objects that obstruct the spray arms. I dont know because theres nothing that tells me why the machine is beeping when I attempt to start it. I check the spray arms, move dishes, try to start it again and still get the beeper. I have done this over and over and over again and still it beeps. I have essentially emptied the dishwasher and it still beeps. When it does run, I have to use the boost temp. option and the longest cycle available to get dishes, and I mean dishes, even passably clean. Forget pots and pans, or casseroles. So, if you own a GE dishwasher, I hope that you have the old fashioned dishpan and dryer rack handy. Bottom line, it doesnt clean well, leaks, and beeps every single time I try to start it. Buy something else.

I purchased a General Electric model peb7226df1ww in 2013. It lasted two years, then failed. I replaced it and two years later the replacement failed. At least GE microwaves are reliable in that aspect. You can count on them to fail. I am convinced GE installs a delayed kill switch on their microwaves to help their revenue stream. This was the last GE appliance I will ever purchase.

I cook a lot of popcorn in my microwave and it hasnt burn a bag yet. It warms food quickly. Also, it cooks bacon really good. But the best feature is the steam cleaner that saves me time. It steams for about 2-3 minutes then all I do wipe the steam off and its clean.

GE Microwave was making intermittent buzzing noise 1 month after purchase. Called GE & they said they could send a tech out to check it but if they didnt find anything I would be charged a service call. I stated it would only do it once in a while so was concerned it wouldnt do it when tech was here & I would be charged so I passed on the tech. Microwave continued to make noise periodically but seemed to get less as time went on. 1 year & 10 months later it started to sound like it was arcing & shut off. Again it was periodic. Called GE. They sent a tech out & it only shut off but no arcing sound or intermittent starting & stopping. Tech stated it probably was door micro switch, but when GE called me back they said he stated it probably was circuit board. Whatever the cause it is still what I would call arcing & going off & on.GE stated They could give me a discount on a new microwave which amounted to cost of $100.00 more than I paid for it in the first place.

Door would not latch, so entire locking mechanism was replaced. Still wont lock. Repairman said it looks like door is warped or bent and door may need to be replaced. We have used the dishwasher twice a week for a year and suddenly it wont lock. Have heard this is a common issue. Is this true? Is there a recall?

Beware of GEs scam! My new house came with a GE microwave oven model JVM1630. It no longer heats food so I called GE repair. Heres basically what they told me: It is likely the magnetron tube and it is still under warranty, so no charge to replace it but I would have to pay $99.95 for the repairman to come to my home to diagnose the problem. If I decided I didnt want to repair the microwave, I was offered a $100 coupon toward a new one but it had to be a GE and it had to be bought on their website only. If I decided to go ahead with the repairs, the $99.95 would be deducted from the bill and I would only have to pay for additional parts and labor. I repeatedly asked for a ball-park labor charge so I could make an informed decision as to whether it was cost effective to have the repairman come out or just get a brand new one elsewhere. The person on the repair line hung up on me! I called back and I was told the same thing; that no one could tell me what the labor cost estimate might be. I asked to talk to a supervisor and same story. I didnt schedule a repair because I was taking a long trip and wouldnt be using the microwave anyway. When I returned from my trip, I called GE repair and again they wouldnt give me a ball park figure. Frustrated, I decided to have the repairman just come out and repair the darn thing and an appointment was scheduled for the next Monday. I had to rearrange a Monday day trip to Wednesday and set the repair appointment. On Monday, it was starting to get late in the afternoon, so I called to find out if the guy was on his way. A recording said my call was noted and I would be receiving a follow-up call. About 10 minutes later, Kim in dispatch called to tell me she had to reschedule the repairman to Wednesday. I explained I already had an appointment on Wednesday. which was already changed because it conflicted with the repairman coming to my home. She told me the repairman couldnt come because his truck wasnt safe to drive so that whole day was shot. The appointment was rescheduled for Wednesday and I had to again reschedule my other trip. When the guy finally showed up on Wednesday, he told me to put a glass of water in the microwave and start it. Ten seconds later, he declared it to be the magnetron tube. He was at my house about 10 minutes, just long enough to take my $99.95 credit card payment and to give me an estimate of $246.90 to repair the microwave which included the free magnetron tube, a $20 part plus tax and labor. The estimate had instructions on how to get the $100 coupon if I decided to buy a new GE microwave, which he said is what most people do. He didnt seem like he came prepared to repair the microwave at all. I was so frustrated and already out the $99.95, so I told him to go ahead and repair it. He said I should call repair to schedule him to come back to repair it! I told him to just repair it now and he said he didnt think he had a magnetron tube in his truck. I asked him if he would go to the truck and check! He did, and nope, no tube and he left.I think this is a great scam GE and maybe others have going. Its entrapment. They get you to accept a repairman to come to your home and charge you nearly $100 for it, but give you a coupon for $100 for a new one but it has to be a GE and can only be bought from their website where they can go as high as $500 or $600. By the way, I got on the website to find a replacement. My model had been discontinued and the only one in my price range was also a discontinued model. They charge $75 to come out to install it and another $30 to take away your old one. I called local appliance stores to see if I could unload my old microwave for parts and they all said the same thing: stay away from GE products.

GE over the stove microwave stainless Steel Adora made for Home Depot. It started to make a funny noise and then it wouldnt heat. I contacted GE about the problem. It would be $89.00 to come out and an additional $25 for the double wall oven that would not stop beeping and would not work at all. We purchased a GE double wall oven at the same time as the microwave. All of our appliances were purchased in 2006. All GE and we are worried they are all junk. My husband took it to an appliance repair place and they said the Magnatron and the diode went on the machine. They said it is basically junk! Disgusted. Dont buy GE. They make junk! I just had to dispose of this piece of trash!

Cost of washer $749.95 plus 4-yr warranty, install and hoses, $273 equals $1,023 for this GE stainless interior tall tub dishwasher GLD8700N20BB that only lasted 6 years and 4 months. It wont run, wont fill with water, nothing. Six years. Time to buy again. My advice, buy a cheap one and replace it every 36 months and forget the extended warranty. Installed: Sept. 2009. Dead: Jan. 2016. This was a replacement to an LG dishwasher that completely flooded my kitchen and caused a total tear out of my kitchen, and my homeowners insurance took LG to court. That LG cost $42,000 for a new kitchen and months of contractors and work. Washing dishes by hand is looking better every day... Think about it.

Dishwasher works great, I just wish it was a little bigger. I usually have to work hard to get everything I have to wash into one load. But if I could give it a 4.75, I would, because dishes are spotless when I remove them.

I recently purchased a GD720SGF2WW Serial #HD744674B GE dishwasher. From the moment I tried to use it there was a leak from the bottom of the door. I called for service and when they came the repair man said the door was leaking and there was a repair kit for it so it must be a weak spot in this particular dishwasher, which by the way was not a cheap model and was stainless steel lined. I waited a month for further service and when he finally came he realized he had mistakenly diagnosed the problem and it was a crack in the lining of the door which had gradually gotten bigger as I waited for service. So this NEW dishwasher had been leaking onto my newly installed hardwood floor. By this time I had no faith whatsoever in this dishwasher and said I wanted a replacement. I was called back and told that they would only repair it, which I have been trying to do since NOVEMBER and it is now Jan 21! I will no longer buy GE products and when I called customer service I was on hold for 20 min and finally hung up which Im sure was their intent.

Periodically my GE Profile Dishwasher will not clean well. On every occasion it is due to clogging of spray ports on the upper and/or lower spray arms. Removing the blockages is nigh-on impossible as it is often not possible to extract the blockage from the outside and its not at all possible to flush the blockage back down the arm to extract it at the centre. All that is required is a bit of forethought and the creation of some access to the arm. I was frankly surprised to not be able to find a replacement arm as the suggested solution to this problem, the additional part revenue being part of GEs the business model. There are a number of other design issues with the assembly at the bottom that make me think it was done by an intern and nobody checked her work at the end of summer break before it went into production.

I have had 2 Profile dishwashers in the past 3 months. I have not been able to use either one. First one had a cracked tub and the replacement would not run. I tried for hours to contact GE customer service and was placed on hold for almost an hour before they closed for the day. Not only is this washer a piece of garbage, GE customer service is terrible. Do not and I will say this again do not but this product.

Our first microwave lasted 15 years now this one 1.5 year. No help just buy a new one. Or pay 100 for their service call. 100’s of consumers with same exact problem and they just get away with it. Ridiculous.

Ease of use, intuitive and good looking. Compliments my existing kitchen appliances and decor. I have a GE profile and has lasted now for about 6 years. I really don’t have any issues with the microwave and never needed any kind of service on it.

Microwave oven 2008 - The food doesnt go around anymore. The glass insert does not turn. What can I do?

Model WES1130 GE Microwave - The entire interior of the microwave just started peeling off the coating/finish around 3 years after purchase. The turntable wheel guide path totally disintegrated the finish of the path. It still worked but was so unsightly and disgusting to look into the interior and possibly dangerous to eat anything that had been put inside to cook. I just got rid of it. I purchased another GE Model JES1460DSBB and it started malfunctioning after 3 weeks. I returned it and will not buy another GE product.

Model gdt580sgfbb - About 2 weeks after the warranty expired, the dishwasher stopped filling with water. So, our friend replaced the water inlet valve. No change. If you pour water into it, it kinda pushed it around, but empties it out, wont refill, and starts whining. Then, if you open it, and turn it off, and re -shut it, it starts itself back up again! What?! This stupid thing is essentially brand New! To be truthful, it has never cleaned very well, leaving residue on dishes, and NEVER getting dishes dry. I regret buying this item! And its still not fixed. I will not buy another GE appliance.

Model JVM1740DP1BB - GE Microwave - complaining since November 2014. Great microwave UNTIL the inside ceiling bubbled and began to flake off in various locations. A service tech that visited our home advised us to call GE and advise them of a potentially hazardous situation. The GE rep offered to sell us a new microwave but only stated that we were out of warranty, although this is clearly a manufacturers defect! She proceeded to tell us the lining was perfectly safe but maybe we shouldnt operate it. I have written GE management to see if they will assist in replacing the defective unit; GE is the reason we purchased it to begin with (but it may be the reason never to purchase one again).

I like the electronic beepings that let you know your settings, and it can be changed to your preference. I inadvertently hit the settings button and turned off the beeping and I thought the microwave was failing after only 3 months, but I discovered my error, fixed it, and all is well.

The GE microwave we use is almost 17 years old and has never needed any repairs. It is everything you could want from a microwave.

GE Profile microwave Model: PEB7226SF1SS came as part of the builder installation. In the first year had issues with the microwave not starting intermittently and had to call GE support who sent in a technician who had to work on the door alignment and the switch was the problem which said to have fixed. About 2.5 year from purchase the heating seemed to be irregular which we did not take much notice and then it stopped working completely. We called GE support and did get the usual routine of the product being out of warranty and have to pay for the technician. While scheduling they realized they did not have a their own service person in the vicinity and was advised to reach out to local service person.Local technician diagnosed that the magnetron has gone bad and advised most manufacturers have 10 years warranty on the magnetron as they are supposed to last for a long time and I should reach out to GE. Having reached out to GE support again to our surprise were advised that unlike most manufacturers this product did not have 10 year magnetron warranty. Customer service, part service and customer relations kept redirecting to each other. GE does not provide an option to sell the replacement magnetron to the customer and now want their authorized center to be engaged and paid again to have the part ordered and installed. Disappointed with GE product quality, their stand on warranty compared to their competition and their service which has given me run around and no solution. I have written to them asking for solution which they havent responded yet.

Touch panel gets too hot from the stove and fails. Have to unplug it all the time to reset. Door handle unscrewed and inside coating is peeling. Had repaired three times. When least expected, I have to empty the cabinet above to reach the plug.

I purchased this in Feb. 2013. Just before the 1 year warranty was up the control panel went out. They came and replaced it. Now just a little over a year of the replacement, the control panel went out again. Worst microwave hood fan Ive ever had.

Microwave and convection oven together...perfect for heating food or baking. Very easy to operate. G.E.profile. Mounts over the stove with an exhaust fan and lights. Also has a rotating plate in it to heat evenly.

I had a blow up with my GE microwave which came with 2 metal racks. I used the rack once and the microwave flared up as if I had warmed something on aluminum foil. I removed the racks. The microwave is 2 years old. Last week I warmed a chocolate chip cookie on a paper plate for 10 seconds. Immediately the microwave flared up, the plastic bracket that the shelf rest on burned and melted. I was lucky no one was hurt or a fire resulted. GE came to inspect the microwave and offered to replace it for $258.80. I am arguing with GE. I want them to replace it free of charge. Their own technician tells customers to never use the metal shelves. I maintain that the design or brackets are faulty and GE should stand behind their products. This microwave was always used correctly. Do consumers have any rights at all?

The wheels to roll tray in and out comes off sometimes, other than its fine, average wash cycle. Doesnt really clean heavy food off dishes so have clean first then put in dishwasher.

I have a GE Profile model JT965SK4SS micro/oven combo. It came new with my new home. A couple years into it, the paint (lining) interior of the microwave start to bubble and peel and eventually started rusting. Had SEARS come out (warranty had expired) who contacted GE and they concluded it was only cosmetic that it doesnt affect the functioning of the microwave. Well, its gotten a LOT WORSE now, bubbled peeling paint all over inside, rust, exposed metal, and the paint is falling onto food. I can NOT even wipe out the interior to clean it, it makes more stuff come off/fall down. I called GE last week, was told by 2 employees that it is NOT safe to use anymore, discontinue use. I had SEARS come again (per GE). The tech said he had NEVER seen anything like it before. He called GE to tell them its not safe, exposed metal, and its dangerous. They again said, well maam, youve gotten 8 years use of it. We wont replace it, but will offer you a discount for a new one ($2,500 out of pocket for me). The person who had offered me the discount (yes, I sent pictures, showed how bad it is) also gave me a tip regarding the unit I have now with the exposed metal and the chance of arcing (spelled? like Ark) if the unit catches on fire, make sure not to open the doors, the fire should contain itself. 2 employees told me its not safe, a 3rd gave me helpful info for if/when it catches on fire... and yet, they still wont replace the unit... and do not stand behind their own products. I plan to go to our local news station, see if they can get anywhere with this, since they wont do anything. Patiently waiting and unable to afford a new unit.

We had a GE microwave that my parents got when I was in elementary school that lasted us through graduation (when I got it), and it then lasted me another 6 or 7 years after that. It was a great microwave, so we went with GE for our next one. What a mistake that was. The new one died completely less than a year after we got it (less than a year after its manufacture date at that!). The one after, one of the same make and model, lasted 3 years to the month after its manufacture date. Sorry GE, but I just do not have any interest in spending so much for so short a lifespan on your products, and its a damn shame that your quality has suffered so badly that you have lost a once-loyal customer of your brand.

Entire inside is plastic crap. Dishwasher is very loud and takes a long time. Racks are ok but cheap feeling. If I was choosing, I wouldnt buy it. This GE was in new house. Overall feel is very cheap. Too much plastic. Very low end builder model. Steel inside or heavy plastic will take more beatings.

We moved into our home just over a year ago. We replaced all of the kitchen appliances; refrigerator, stove, microwave, and dishwasher with GE slate gray appliances. This was in November, 2014. On New Years eve (2016), the dishwasher flooded the kitchen. I removed the kick panel and saw water pouring from the pump. After the holiday, we finally got in touch with the appliance repair shop who handles GE warranty work in our area.They contacted GE on our behalf to see if GE would stand behind a product that was just over 1 month out of warranty. Bear in mind, this wasnt something simple like an indicator light burning out, this failure was catastrophic. GE basically told them (and us) to pound sand. We are a 2 person family. The dishwasher was used maybe twice a week during the year weve owned it. Amazing quality! Now Im looking forward to watching the rest of this stuff fall apart. It looks like the life span of the product and the warranty period are the same. How handy for GE. They must not have to depend on repeat business or take these negative reviews seriously.

My GE Profile dishwasher is now 4 years old and Ive put up with it not cleaning well. For the last 3 years, I get a cloudy gray film over the dishes and finally figured out what is happening!! There is a gray rubber/plastic border around the bottom screen piece that has all the holes in it and covers most of the bottom of the dishwasher. I gently scraped with my finger and lo and behold its like gray putty!! So, the whole border of this gray rubber/plastic is disintegrating!! I had a 4 year warranty from Sears and they sent out a repairman. He is just going to order that whole screen part and replace it. He scraped the rubber and it came off for him too!! He said he never saw that before. He said it is probably the fault of my detergent which comes from health food stores and NOT the Cascade that they promote. Anyway, now I know where the gray film is coming from... Weve probably been consuming this for 4 years, a little at a time (NOT GOOD)!!! Im not thrilled with Cascade either!! Probably my LAST GE product to buy!!

Its an older Hotpoint, and the layout is fairly roomy for a dishwasher of its size. The last apartment I was in had a comparably sized dishwasher that had too many shelving elements that got in the way of being able to just shove some dishes in there. Ive discovered with this dishwasher I need to stick to powdered detergent because the Hotpoint doesnt fully dissolve tablets. It does a fine job overall, though.

The GE repairman just left. It wasnt the coil that was flaking, it was the eco dish washing detergent I was using. The detergent wasnt dissolving, it was clogging up the jets and burning on the coil. What I was seeing was black burned detergent flakes. The repairman gave me citric acid to use to clean out the clogs (for free). He also didnt charge me for the visit, even though it was my fault. He also told me to get the water in my sink really hot before I start the dishwasher. I am very impressed with his service!

I have a GE dishwasher that shut itself off after three uses. It was rebooted by a repairman, and worked once. GE repairman called to let me know and I was originally scheduled for today but have been canceled. I’m taking the day off but for nothing. There’s no number to call. There’s no one to complain to. JCPenney is not standing by their merchandise because I did not buy an extended warranty. Originally purchased in November 2017. The machine was replaced by GE in December 2017. I have a dishwasher that I paid over $500 for and I’ve used it four times.

GDF520PGD088 - Never again GE. If you just invested some money in your R and D for the products you sell, maybe I would not be calling you all the time to fix what was broken to begin with. So to sum you up, 600.00 purchase, the day it was deliver and installed, another 200.00 and it still will not work properly??? I found out that there were 2 recalls on this product while sitting in the warehouse for sale, I guess I was lucky. 6 service calls later, still does not work properly and you want continue to charge me service calls for this disastrous dishwasher of 3 years. No I am done and I will share this horrible experience with everyone I know. Buyer of GE product, please beware. Quick to take your money yet irresponsible in standing behind their products.

Fact no. 1: On 02/25/07, I supplanted a burnt-out 12-year old Kenmore microwave oven. Regretfully, my replacement of choice is a GE JES1456WJ02 unit acquired at Home Depot in Cumberland. At that stage, my spouse was afflicted with an advanced case of Parkinsons disease, and eventually, I had her concerned caregiver reporting having found chips of paint spread on food extracted from the new oven. From that point onward, I established a close watch of the infamous appliance, after confirming that the chipping paint originated from the roof of the GE oven. But I withheld from filing a claim with GE at the time because my wifes health deterioration absorbed all my attention.Fact no. 2: But on 12/12/09, a couple of months after my beloved one passed away, I decided to take the oven to a Home Depot claim department where they immediately agreed to replace the defective unit for another one of similar characteristics. With a sigh of relief, thinking that I had taken care of the problem, my assumption was incorrect.Fact no. 3: Today, 10/28/11 in fact, I discovered chips of paint floating over a plate of soup extracted from the GE oven. I was aghast! I couldnt believe it! Still, further inspection determined that the lousy internal coat of paint is likewise peeling off from this monstrosity appliance manufactured by GE.

This is the second digital microwave I have owned. Both of them have been GE brand. There is nothing fancy about them but they are very Easy to use and get the job done. The first unit lasted about 15 years before it had to be replaced. It was used almost on a daily basis, so I feel I got my money’s worth from the unit!

After a year and a half the dishwasher stopped draining. A $231 service call removed the three corn kernels and one watermelon seed that caused. See it all the time says the happy repairman. Another good example of why not to trust GE. Mrs. Gs sales and service complicit in the deceit.

I owned a previous GE dishwasher 4 years ago and would give it excellent ratings. I bought a newer top of the line version when I purchased a new home. It simply fails to clean dishes. Wet food that any dishwasher would remove, remained on the dishes. The drying cycle never dried the dishes. We have to hand wash the dishes now and have stopped using the dishwasher after 3 days of ownership because of health hazard. I called Lowes about this within days of the install. Lowes sent out the installer who claimed the machine was installed properly. Then Lowes scheduled a GE repairman to come to the home. We waited all day for him to arrive for a morning appointment. He never came. Lowes stepped up and is replacing the dishwasher with a non-GE product. I would not touch a GE product again given the lack of service and commitment to their product. I feel confident with Lowes, but not with GE - their ethics from engineering, manufacturing and servicing are very suspect with us.

Called in for my washing machine and got service on my dishwasher??? With a bill of $207. A scam. Please take my advice and never call GE.

GE appliances were installed in my new build home including a brand new, never used microwave. When we did our walkthroughs the microwave appeared to work (turned on, timer ran, etc.) but after signing we found out that the unit was a dud and the microwave emitter did not work so nothing was ever heated regardless of the run time. We have called GE several times only to get extremely rude and dismissive customer service reps (“Audrey” if that was even her real name). They refuse to replace a brand new unit that never worked and insist on trying to repair it, but we are also being told that this will take several trips as the technician will only first come to inspect it then a second trip will be needed to bring out the necessary parts (they don’t carry them in the truck because they are “fragile”). I’ll never be using a GE product again.

I purchased a GE microwave just a year ago. Ive had a few problems with it like the round glass plate that you cook food on cracking in half twice when the microwave wasnt even in use, and the control panel going stupid... requiring me to unplug it to get it back on track. The worst part is I purchased an entire kitchen work of GE appliances at the same time and Ive already had two service visits on the dishwasher.GE customer service is the worst! When I call they just keep repeating themselves and they never listen to what Im telling them. Today was the worst yet... I got this woman on the phone and she just kept telling me the microwave was not in warranty any longer as of last month. She also told me she only has two appliances listed on my account (no range or refrigerator) when they were registered at the same time as the other appliances and they have sold me filters for the refrigerator several times. All I can tell people is if you are considering buying GE appliances... DONT! They SUCK!

I recently purchased a GE Profile 1.9 microwave oven from Home Depot less than a year ago. Last week I went to remove something that I had cooked and went to close the door and it would not stay shut. I ended up getting some masking tape to try and tape it shut in order to keep the light from staying on and burning out until morning when I could get a better look at it, thinking that it had to be something small that could be taken care of without any problem. Hinge adjustment, something getting in the way that I couldnt see, etc, etc. Wrong! I have been over this door with a fine tooth comb and there is nothing that I can see that is preventing it from staying closed, not only that but according to everything that I have read, I am very lucky that I didnt get fried while trying to figure out if the latching mechanism was functioning correctly. I am not even going to go through the long drawn out process of dealing with GE over this due to the simple fact that I have been there done that with my dishwasher that showed up with the front panel dented a few years back from the factory and I ended up blaming the place that I had purchased it through instead of GE and have since found out by reading other complaints that this seems to be something that is not unusual when it comes to GE appliances. I spent over 1100.00 dollars on the dishwasher and they only replaced the panel instead of giving me a new one, and I have never been satisfied with the way that it operates, and it was a very long and drawn out process and I am just not willing to spend the time again on another one of their products. It is unfortunate that we have entered a time where customer satisfaction means nothing, and the days of caring about having repeat business from a satisfied customer are over. The prices continue to rise on the things that we have become to depend on and cant seem to live without, but the quality and workmanship have not only diminished but also present safety threats. I will never purchase another GE anything and I am looking forward to the day when we all have finally had enough of this and do something that makes these companies stand behind the products that they sell and quits ripping the consumer off. Its rampant across the board no matter what you buy, and there should be laws in place in order to keep it from happening. We have laws for everything else, why not have a couple that protect the consumer and their pocket books.

The GE microwave oven that was installed by the owners of my 130-something unit apartment complex caught fire in June 2014. The manufacture date is listed as December 2012. I moved into the unit in June 2013 and the microwave was brand new still and had never been used by anyone else. I myself rarely use the microwave and only use it for heating up cold food that I previously cooked on the stove top. After heating up rice using the 2 minute express option and removing the food from the microwave, I had gone to the restroom for 30 seconds only to return and find the microwave on fire. The fire ignited from the ceiling of the microwave. I had initially intended on going to the bathroom to take a shower but needed to open a new bar of soap, so I had only returned to the kitchen to throw the soap packaging in the trash. Had I not done the latter, my entire apartment could have caught fire and it would have been difficult if not impossible for me to escape from my third floor apartment. Reading all of these complaints it is really hard to believe that a government agency has not stepped in and forced GE to STOP MAKING MICROWAVES! From the complaints on this board it is clear to see that every year GE continues to make appliances that put consumers safety and lives at risk. You would think that after so many recalls that they would have perfected their product by now, but that is not the case. It almost seems as though they are just slapping new model and serial numbers on the same BAD product. The management in my building contacted GE and my microwave was replaced with another GE microwave manufactured in 2014. I did not want another GE microwave, but I only rent so I didnt have a choice. I used the microwave once so far and the fan automatically came on after 2 minutes of use. It does state inside the microwave that the fan may come on automatically, but I just dont trust this brand anymore. I have a countertop microwave that works perfectly fine that Ive owned for over 15 years that I will be using. I will unplug the GE microwave and just keep it for aesthetic purposes, since thats all its good for.

I have owned my dishwasher for 5 years. Monthly, I use dishwasher magic to clean the inside, removing lime, minerals, rust and grease. The lower rack, under the silverware rack is completely rusted. I have used and owned dishwashers for over 35 years and not once has one rusted like this. Poor quality for the racks! I feel it should be replaced free of charge.

Our stainless steel finish 1100 watt JES1142 microwave is around 2 years old. Within the last year the finish inside started to corrode (yes, my wife cleaned it regularly with a non abrasive, appropriate cleanser). Also, the door latch button started sticking and a few days ago it just stopped heating. Unfortunately I cant find my receipt, but I bought it at my local Lowes on Bell Rd. Nashville TN. Serial # is MA212483G. Manufactured July 2013. Was this just a lemon? Very disappointed.

I purchased a Ge profile top of the line microwave installed over an electric oven. After 3 months the plastic handle came off and Ge replaced the entire door. This handle has now come off 3 times. The service tech said it has a plastic connector that weakens over a stove. It supposed to be mounted over a stove. This is just poor design and totally unacceptable for their top of the line microwave.

Touchpad for CVM2072SM2SS stopped working. This touchpad has been creating issues for the last couple of years. Few reconnection of wires got it working for the last few times and now it is completely broke. GE is not ready to help with fixing the issue. It wants to sell me another microwave CVM1750SHSS which seems to have similar issues (also the plastic handle for those microwaves seems to fall apart due to heat). In fact, the reviews for the whole range of GE Cafe series seems to be pretty bad. GE is not owning up the design issues. Too bad!

We bought a new GE microwave oven in 2007. It failed in 2018 after much, much use. We replaced it with a Whirlpool which failed in one week. Lowe’s let us return it and we bought another GE like our original and we are very happy with it.

Bought a PDT845SSJ2SS in June. Two months later, it has a leak. Good news, has a leak detector which shuts down the machine. Bad news is that it leaks and the leak detector worked! Called GE. We dont have an authorized service technician in your area. We will get back to you within 3-5 days. Three days later, after I had raised rain with my appliance dealer, he arranged for a local dealer to come look at the machine. Scheduled that appointment - it was Friday, and We only come to your area on Tuesdays and Thursdays. Next Tuesday is booked, so we will try for Friday. Then, someone from an organization called Platinum Services calls and says GE has assigned the ticket to them. Shes going to try to schedule a diagnostic appointment in the next 7-10 BUSINESS days. Told her to forget it (found out she was calling from Lowes and had to find a technician before she could schedule.) End of week 1. Following week, someone else from GE calls and asks if I was cancelling my service request. In the course of the conversation, she asks to confirm the model GE RANGE that I have. Kinda lost it on her... On Thursday serviceman from local dealer comes. Turns on the dishwasher - it leaks exactly where I had said it would. Need to order a part and GE will not expedite. End of week 2. Next week - crickets. Nothing, Nada, mushroom mode (in the dark and being fed BS). Called my appliance dealer today and told him to come pick up the dishwasher - says he cannot do that. I explained, “I will forfeit the money I paid - I dont want a dishwasher that leaks in the first two months of use.” He tell me GE released the part yesterday...whatever THAT means and he HOPES repairman will come next Tuesday to repair. So, I have had a new GE dishwasher for 3 months and it has only worked for 2. Be aware! I assume partial responsibility for this goat rope - I faithfully refer to Consumer Reports when purchasing appliances and electronics. I suggest you do the same... you will find GE listed AFTER BOSCH, KITCHENAID, KENMORE and others. Also, realize the GE brand is now a CHINESE company. Caveat Emptor!

We moved into our new manufactured home in May of 2013. That is the month our above range built-in GE microwave was installed. In October of 2013, one of my sons heated a frozen chicken cordon bleu serving for 3 minutes, 45 seconds, according to packaging directions. He said that some of the inside of his food was cool, so my other son put in his serving for four minutes, zero seconds. All of the packaging was removed and each serving was placed on a separate Corelle plate and covered with Glad microwave-safe plastic wrap. While heating the second serving, the microwave started on fire. Fortunately, my son extinguished the fire before it spread. The food did not combust. The fire seems to have started from the ceiling behind the fan. The entire inside of our microwave is clean except for the soot that billowed out from the center of the ceiling. When the service tech came, he scrubbed the soot off of the ceiling with some paper napkins (which he left inside of the unit) and said that the microwave was a total loss. He also said the fire was caused by misuse, because plastic wrap is not meant to be used in the microwave, therefore even though the fire happened within a year of purchase and installation, our warranty was void. I asked GE to get a second opinion and they agreed to send a third party servicer (A&E) who stood me up three times! I finally got to schedule a GE tech to come at the end of December and they sent the same guy who said the fire was our fault! He told me that he never said plastic wrap is not meant for the microwave, but that we are being dishonest because fires only start when the food is left in the microwave for too long. He accidentally let it slip that he is seeing the same problem with GE microwaves in a lot of new construction for student housing in Tallahassee. (We live 20 minutes south of there.) He attempted to recover GEs reputation afterward by saying that of course it was the students faults, too, for misusing the microwave units. Anyway, GE has graciously offered to sell us a new microwave at slight discount. Haha, no thank you!