Periodically my GE Profile Dishwasher will not clean well. On every occasion it is due to clogging of spray ports on the upper and/or lower spray arms. Removing the blockages is nigh-on impossible as it is often not possible to extract the blockage from the outside and its not at all possible to flush the blockage back down the arm to extract it at the centre. All that is required is a bit of forethought and the creation of some access to the arm. I was frankly surprised to not be able to find a replacement arm as the suggested solution to this problem, the additional part revenue being part of GEs the business model. There are a number of other design issues with the assembly at the bottom that make me think it was done by an intern and nobody checked her work at the end of summer break before it went into production.

We had purchased the first listed model of dishwasher (Model PTD7505SSF8SS) and installed it on Aug 27/16. It worked for a total of 13 days and broke down on Sept 9/16. After a good deal of phone tag - a technician looked at it and said no less than 3 internal components had failed, the unit needed to be replaced. We were without the unit from Sept 9/16 until Dec 23/17 when the new replacement unit (Model PTD845SSJOSS) was installed. It worked for a total of 20 days and broke down on Jan 12/17. More phone tag... Tech looked at it and found a number of issues (motherboard, door switch, etc...), in addition - it had been leaking water under the dishwasher for the time it was in service. (All 20 days! What a record!)When a dishwasher leaks upstairs... It doesnt go well for the drywall ceiling downstairs. (The rep at GE was cold and calculated informing me that is what insurance is for!) Im not sure that is what someone who spent $1,699.00 for a GE product (in good faith of a reputable product) expects to be told by the individual who has the ability to make things right? At any rate, this is what you can expect from the trained professionals at GE. When they finally got around to looking at my file... They decided to simply replace the motherboard in the hopes it will fix the leak also.I would have liked a refund at this point (not likely) so I requested yet another replacement (given the issue of water leaking), they absolutely refused. As of this date Feb 2/17 we are still without a dishwasher. Goes without saying - no more GE products will enter our home and I will share, with everyone I can, the caring and kind words of support I experienced from the top level at GE.

I was sitting on my couch and I heard something running. I walked into the kitchen and saw my GE Profile microwave was running. At first I doubted myself and thought maybe I did something and then I cleared it out and went and sat back down. It did it again and again several more time. This is very scary. It was running like someone had set it and it was getting hot inside. Im not sure what else to do. The last time I had the same type of problem and just bought a replacement microwave and now this one is doing the same.

Our GE Microwave Oven/Convection Oven Combo (Model: PT970SRSS) is a little over 2 years old. The interior paint on the ceiling of the microwave oven is chipping and bare metal is exposed. In addition, the microwaves glass turntable frequently slips off its plastic tripod base. Circular scratch marks, which also expose the underlying metal are evident in the area which is located directly below the glass turntable. The circular scratches are a direct result of the glass turntable scraping against the paint. The GE repairman said chipped paint is not repairable and that paint should not ever chip in a microwave, let alone a relatively new microwave. After many calls back and forth to the GE Consumer Relations person, we were offered a new combo at a discounted rate of approximately $1,000. (We paid around $2,000 originally.) Im not satisfied with this offer. I strongly feel that consumers should NOT have to pay to replace a defective item. GE needs to pull these defective and dangerous products off the market! Take a lesson from GM!!!

I wish I had found this complaint section before I purchased my microwave. Bought model HVM1750DP1CC in May of 2010. Now, 3 years later, all of a sudden theres no power to the unit. The wall outlet is fine. There were no storms around here when it went out. It just seemed to fry itself! The repair/troubleshooting instructions tell you to get a licensed technician to check this and check that because of the voltage. They give you a flowchart to troubleshoot it yourself, but no pictures to go with the diagram. Sure I can check the fuses, if I knew where they are!GE - NEVER AGAIN FOR ME. Wish we still had good-valued products Made in the USA. This one is made in Malaysia. NOT WORTH IT. Time to sell the GE stock too. Their products suck and class action suits will probably follow. Kris is Pissed!

Ever since I bought this dishwasher in Jan 2014 it hasnt dried properly. Finally had a tech come out and he told me the water wasnt hot enough. How is it energy efficient if I have to raise the heat in my water heater to get the dishes to dry???? Very dissatisfied! My old dishwasher (with plastic lining) dried the dishes with no problem. I had it for 16 years before I had any problems with it. This new one is a problem from the first time I used it. No GE ever again!

I have a new GE profile model PDWT380VSS - Two in fact. The first one kept breaking glasses in the top rack. GE technicians could not find an answer so they replaced the Dishwasher. Now six months later its doing it again. This replaced a perfectly good, older model as part of a remodel. Theyll be sending another tech who I suspect will not have an answer. Any thoughts on what could be causing this or a way around it or is it to be expected? The first GE profile I had for several years with no such issues.

I bought a GE Adora dishwasher from Home Depot. There is nothing technically wrong with it - in other words - it is not malfunctioning. It is just that its normal operation is AWFUL, in my opinion. The PROS: it is very quiet. The CONS: it does not clean your dishes! And since this is the primary function of a dishwasher - I would say it is a complete failure. Originally, I had hard water, and I thought that was probably the issue. I purchased a whole home Kinetico system, which remove almost all particulates from the water, and makes bottled-water-quality drinking water. (On a side-note, I would TOTALLY recommend the Kinetico system!) But even after having the water issues fixed, the dishwasher has NEVER worked properly. I have used every type of dishwasher detergent, including Cascade Complete & Platinum, Finish Ultra & Quantum Powerball... and I have also added rinse agents etc. Basically - whatever state your dishes are in when you put them IN the dishwasher, they will only be slightly improved when you remove them. Even if you SOAK the dishes first, they come out with all kinds of residue. It does an especially horrible job on glassware, but silverware is also terrible. And I have to re-wash by hand every coffee cup that comes out. I truly loathe this machine, and will replace as soon as I do enough research about a better brand & model.

I have to agree with other post about the customer service. Our dishwasher is only 15 months old. First call went fine after that everything is with email. Tried calling several times to get correct parts shipped after only getting one of three needed, I called and finally after 45 minutes an agent answered. After several attempts to get recommended parts and repairs we are now having additional issues. The quality of the GE brand has really gone down compared to our older products that lasted 15+ years. Now waiting for a new assessment of what the issue might be and hopefully will be able to get the parts without issue.

I bought this JVM1540SN1SS microwave just two years ago. From past five months, certain keys stopped working. Then today, it gives me error service may be required - keyboard shorted. Microwave is unusable at this point and out of warranty. But my previous microwaves worked for decade without any issues. This one broke in about 1.5 years. These microwaves are of bad quality. I think GE should recall these microwaves and get it fixed free of cost for consumers.

The microwave oven that I’ve been using works real well and it’s not that expensive. It’s also a convection oven at the same time. The only reason I didn’t give it a 5 is, I rarely give that high # to anything with rare exceptions.

Our GE Cafe Appliance package is less than 1year old and the convection/microwave door handle is wrinkling and peeling. I realize that weight may be a concern hence the plastic vs. metal handle due to the side hinge of micro but aluminum or other light metal would have made more sense. A service tech is coming out next week to replace the in warranty handle however this cost will be our responsible next year when this happens again. A light metal retrofit/recall seems to be the logical solution to remain customer centric and maintain GE loyalty. How this material choice error is handled by GE to ensure this problem does not repeat during the life of this appliance defines brand loyalty. Thank you for your consideration.

GE is a very reliable name brand with history to back it up. I’ve used their washing machines for years and only changed out once due to newer features. I had Thebes first washer for at least 10 years, maybe a little more. It only needed one part replaced, that was the capacitor, otherwise it was still usable. I am not an in depth handy person but I will read and do my research and found directions doable. Additionally, I found the service help desk very informative and that’s how I discovered it was the capacitor that had gone bad after washing clothes for so many years, and believe me, I did a lot of cycles with my kids and family. I feel I got more than my money's worth. Lastly, I’m still using their products to this day. I may not have the frequency because we are empty nesters but I still believe in their products,

Microwave Model JVM1750DP2bb defective construction- Plastic is protruding inside the Oven. Took possession of a new home in January 2014, but only occupied part time. I estimate we had the equivalent of 6 months being occupied. In January 2017 the magnetron broke down, at which time I noticed a piece of plastics protruding inside the microwave through a vent hole on the Magnetron side. I did not take the extended warranty and GE only offered to send a repair man. Since this is an over the stove model venting outside, it had to be repaired or replaced. Checked with the supplier and they estimated a minimum of $ 300 repair cost. Home Depot had model JVM6175DKBB on sale for 249.00, and with delivery, and installation, were talking $ 350.00 to $400.00 to replace. I got in touch with GE Consumer Affairs, and they did eventually agree to provide the JVM6175DKBB for $ 270.00 including installation. They will take possession of the old model, so there wont be any way for me to confirm or deny a manufacturing defect.

Run, dont walk, toward any dishwasher other than a GE. Problems with the dishwasher within one year - black residue on my dishes that felt and smeared like grease. Calls to GE repair resulted in the worst customer service I have ever experienced. One call returned at 4:00 am. After two visits, a lecture about how to load a dishwasher, I gave up. The effort of making calls for visits, taking time off work, rude repair technicians and being told it was not grease, I now have a dishwasher a few years old that is falling apart. Screws are now coming loose and the buttons are sticking.

We purchased this GE dishwasher in October of 2017 when we built our house. Over the past few months we noticed our hardwood floors looking like they were rolling. This week we noticed a small amount of water seeping from under the cabinet. We pulled the dishwasher out and saw a very slow leak from a part of the dishwasher. Called GE and was told it was no longer under warranty. Explained leak has had to have been going on for months so should fall under warranty. Was told because we didn’t notice probably would not be. Sending tech which I will have to pay for to see if he can tell how long been leaking. More to come after visit. So far not happy.

Less than three years ago, I purchased a microwave oven wall unit to replace an existing unit. Due to the size of the built-in cabinet, I was limited in choices. The cost of the unit was $2400. A few months ago, the interior wall of the unit began rusting and the enamel is peeling. I contacted the customer service dept via e-mail on their site. I was asked to send pictures and then informed that I should stop using the unit immediately due to the danger of arcing. I was also told that because I did not purchase the extended warranty, the best that GE could offer me was a new unit for $800. I asked for names of warranty companies and was given one name and number but told there were others that also offered the same service. I called this company and they clearly told me that the peeling and chipping was a manufacturer’s defect and would not have been covered by an extended warranty had I purchased one from any company. Then I contacted the GE repair service center and spoke with them. The man who answered explained that this is a cosmetic problem and that there was no danger of the microwave arcing unless there was less food in the microwave than the size of the area that was chipping. I am very disappointed in the response of GE, the pressure placed on me to make a decision in 7 days or the offer would be withdrawn, and the fact that the service department and the consumer service (complaint) department gave me entirely different responses to the same information and problem. I will probably have my cabinet rebuilt to avoid having to replace this unit with another GE appliance. Who would pay $$1600 for the use of a microwave/oven unit for less than three years? Unfortunately, GE seems to be the only company that makes a unit that fits the existing cabinet in my kitchen. Disappointing to say the least.

Ive had my microwave for 12 years. Ive never had any problems with the microwave since its purchase and very pleased. I dont plan on replacing until the microwave would stop operating or not pleasing in the kitchen.

I owned this microwave for the last 5 years. Easy to installed, good appearance, stainless steel, easy to operate but fancy enough to prepare different meals to include the younger ones. Lighting very good and vent excellent.

Wife called me at work to tell me our house is filled with smoke. Our GE dishwasher caught on fire 20 mins after she did a load of dinner dishes. Thanks to my 10- and 4-year-old kids who were in the living room playing, when they smelled smoke, they quickly ran and got the fire extinguisher and yelled to my wife. They ran out of the house and called the FD. Their quick thinking prevented it from getting worse. While on the phone, I had her go and turn off the circuit breaker. We got lucky this time, someone was home...

Ive had this stainless steel GE Dishwasher model GDF645SMONES with the controls in the front for nearly a year. The dishwasher constantly comes on with the slightest accidental touch. However the buttons that control the cycle settings are extremely difficult to operate to cancel the lock or delay hours features. I have to literally bang on the buttons to get a response. My thumbs are now sore from the constant pushing to cancel that lock and delay features that came on accidentally. Once locked, good luck in canceling anything. Im so disgusted with this $600 dishwasher. Complaints to GE and the so-called warranty company that turned out to be one and the same, have fallen on deaf ears from the day I got it. Do yourself a huge favor, do NOT buy this dishwasher. Customer service is awful.

The defect is in the Gas Control and Thermal Coupling, per my licensed plumber. GE tells me my water heater is still under warranty; therefore, I would like an authorization code to have it replaced by Home Depot where it was originally purchased. Home Depot tells me I need GE to give me the authorization code. BTW, your CS rep was very helpful. She is sending both items to me, but I prefer to have a replacement for the cost my plumber will charge to install parts in a questionable product. Thank you.

It works well. We like this newer GE Profile with many preset buttons such as for different times and food types, and defrost. The last GE Profile MW we got had a knob that got loose right away and hard to use, like a dial-up AOL, so this upgraded model is much more convenient. I like the bigger plate size, and that the turntable can be turned off if we put a rectangular casserole dish in there.

Five years ago I purchased a brand-new condo w/ a GE Nautilus dishwasher installed. This machine has NEVER worked right. Issues: 1. The detergent cup that closes, consistently gets stuck shut, hence only half of the detergent gets dispensed and a second cycle is usually needed to get the dishes cleaner. 2. Dishes are never really clean. Theres always at least one dish that has something left over on it, but its usually multiple dishes. 3. Lower rack started rusting out after 3 years of very light use (used approx 3-4 times a month). Loud. Louder than my washing machine. 4. Replacement parts are ridiculously expensive. A new lower rack is approx $100. My condo also came with a GE refrigerator. It too is junk. Never again...

I bought the microwave in 2005. It is an above the stove type microwave, black color. It has been a great microwave for all of these years and still keeps going. I would buy a GE again. It has been a solid microwave and all parts but the turntable are still functioning after all of these years.

Model #JVM1790SK01. High end GE Profile microwave/convection oven. Purchased and installed in 2009. First off the exhaust fan is terrible and is very noisy. The product itself worked well until recently when now the microwave heats intermittently, one time it will come on and heat, next time nothing. The fan runs, but no heating. The truly frustrating part is I need the front venting and no other units have the vents that blow the air outward, all the new units blow the air straight up your cabinets. Certainly a high end unit should last longer than 5 years with only two adults using it now and then. The cost of the service is outrageous and I surely would not use the $100 rebate on another GE product if they do not last any better than this one.

I have owned my dishwasher for 5 years. Monthly, I use dishwasher magic to clean the inside, removing lime, minerals, rust and grease. The lower rack, under the silverware rack is completely rusted. I have used and owned dishwashers for over 35 years and not once has one rusted like this. Poor quality for the racks! I feel it should be replaced free of charge.

Microwave oven, model # WES1450DN1BB, manufacture date, April 2011 - Your customer service sucks! I called there 5 times today and was told my microwave oven has been recalled, yet no one knows! You dont have it listed on the recall or anything. Your Customer Advocate doesnt know its recalled but your Service Department knows and I was told by them that it says, Do not repair, return to the place of purchase. Yet, I called my place of purchase and they know nothing of it either, but are going to work with me the best they can! It was manufactured in April of 2011 and we bought it around July 2011 (we think it was around then). There are many complaints online about the same issues as we are having - paint all bubbled and peeled off the inside top, and smell of burning wires coming from under it! If something would have happened to someone in my family or to my home, you bet your ** I would have sued the pants off of your company! Someone needs to get their ** straight with what is going on in your company or you are going to have a lot of issues! I may bring it to a higher level just because I am so pissed off that no one was informed about this issue, and something very bad could have or still can happen to someone because they are not getting the information they need! Stop and think about it. Because of your companys lack of communication, someone could die! I am very pissed off!

First, as a new homeowner blessed with select builder-provided appliances, I never imagined I would be authoring this letter 4 months after closing on the new home. Your friggin’ microwave oven light mechanism truly sucks! I lost the two bulbs a week or so ago and purchased two more at the cost of approximately $10, even though a one-year warranty was stated. That was okay, as I was more interested in fixing the problem versus starting some long-range purchase interest. So, and this is the most aggravating aspect, I have the correct pins and life is ** good, and as I attempt to insert the first, the ** pin breaks off. Okay, so I reflect on the horrific engineering of the mechanism, and I softly” align the second of the two bulbs, and the ** pin breaks off again. ** is my predominant theme tonight. As well, believe me, I am going to inform Taylor-Morrison that their respective selection of your friggin’ lousy pieces of crap is corrupt and misguided. You suck, G.E.! I’m moving forward.

I called GE and they said they cant send a magnetron through the mail as it is dangerous. Well then, how do other companies sell a magnetron via their websites? They are full of it and I got the same issue, $59 for part and $89 for service call, and another charge for labor. What the....... I asked, Isnt the $89 the labor? She said No, that is the service fee. What a racket they have going on.I will not purchase another GE microwave, even though my other appliances are GE. My microwave is six years old. My GE refrigerator ice maker also stopped working after 5 1/2 years. I have had GE washing machine and dryer without no real problems after 12+ years. Maybe GE needs a class action lawsuit to shape them up??? Anybody up for it???

We moved into our home just over a year ago. We replaced all of the kitchen appliances; refrigerator, stove, microwave, and dishwasher with GE slate gray appliances. This was in November, 2014. On New Years eve (2016), the dishwasher flooded the kitchen. I removed the kick panel and saw water pouring from the pump. After the holiday, we finally got in touch with the appliance repair shop who handles GE warranty work in our area.They contacted GE on our behalf to see if GE would stand behind a product that was just over 1 month out of warranty. Bear in mind, this wasnt something simple like an indicator light burning out, this failure was catastrophic. GE basically told them (and us) to pound sand. We are a 2 person family. The dishwasher was used maybe twice a week during the year weve owned it. Amazing quality! Now Im looking forward to watching the rest of this stuff fall apart. It looks like the life span of the product and the warranty period are the same. How handy for GE. They must not have to depend on repeat business or take these negative reviews seriously.

I bought GE Microwave JES1139BL03 in 2011 and the white paint inside has been peeling off. I think it is defective because I have had other brands and none of them have done this. This microwave was manufactured February 2011.

One needs to be a contortionist to replace the under light bulbs on this microwave. It is a TERRIBLE design. Why werent the sockets placed so that the prong holes could be visible? One has to do a back-bend over the stove top and then the socket holes are still not visible. DO NOT BUY THIS MICROWAVE. DONT BUY THE STOVE EITHER. IT IS DANGEROUS. THE KNOBS TURN EASILY AND OPEN THE GAS.

We purchased a new General Electric (GE) Adora microwave model DVM1850SM4SS from Home Depot for approximately $355.00 in 2010. It was manufactured in Malaysia and had been in use for 2 years and 9 months before the magnetron failed. I spoke with a GE Customer Care representative on two occasions, and she said that the best that GE could do was split the cost of parts and labor since the 1 year warranty had expired. We had not purchased the extended warranty believing at the time that a microwave generally lasts for many years, and GE had always made quality products and would stand behind them. I indicated that I wanted to have the problem properly diagnosed by the service rep recommended by GE before proceeding further. The 10-minute service call bill set us back approx. $100.00. It would cost at least another $170 to replace the magnetron if we used the service tech contracted by GE. For $270, I believe we could find a fairly nice new microwave. I looked at alternative options for repair or replacement, since I am rather partial to the looks of the over the range stainless steel Adora. The model we have is no longer manufactured, but GE now offers the 1.9 cu. ft. Adora that Home Depot sells for around $400.00. In my internet research, I noted several postings that indicated that due to the high voltage danger of the magnetron, only trained technicians should attempt repairs. After half a dozen calls, I fortunately learned of a Microwave Service Center close to our residence that could replace the magnetron. After taking it down from above the range, hauling it in for repair and paying the approx. $104.00 bill and hauling it back to our residence to mount on the wall, we have a microwave that should work for a while! Total cost including service call for diagnosis - $204.00. Considering that GE does not wish to stand behind the quality of their products, I would not be likely to purchase a GE product again.

2years and 2 months GE Model JVM1540 microwave purchased at Sams quit heating. Everything works other than it does not microwave, GE customer no-service says the part magna something is covered for 5 years, however the labor is not. I offered their customer no-service dept. a deal. If it was my fault the MW broke I will pay the entire cost to fix it but if it was a defective part, they have to pay the entire bill including labor ( which is the right thing to do). They declined to do the right thing.

We have a GE SpaceMaker JVM 239BV 001 over the range microwave purchased about 10 years ago. Within one year of installation the handle snapped - just as numerous people here have stated. I went to our local replacement parts store and was shocked that it cost $30 for a new handle. The sales person said if I were you I would by the lifetime warranty for an extra $3 because you will be back, I sell lots of these.

This GE CVM2072SM1SS Microwave (over-range model) worked fine for five years. Then, we discovered the plastic film over the touchscreen starting to peel. After a bit of wrangling with Consumer Relations, they sent me a replacement touchscreen. The LCD didnt display properly, so they sent me another one. It worked for three months, then in the middle of programming to reheat some food, we got the following error message: Control Fault, Shorted touchscreen - F10. The control has detected a shorted touchscreen and has shut off the oven. It may still be possible to use the oven. However, if this message continues to appear, your oven will require service.The only way to clear the message was to unplug the unit. No amount of replugging in cleared the message. I called GE and they said they would replace the entire unit with a new model under some program they had. Sounded fine to me. I left the house. When I returned, I received a message that their representative called back to say they would not replace the unit, since the program had expired. Huh? I called again, and after a bunch more wrangling, they agreed to send a service tech out and replace whatever needed replacing or fixing at no charge. Of course, they never really made a notation of that, so when he got here, he had to get on the phone and sort it out. Finally, he replaced the touchscreen. Lets see how long it lasts this time.

I have a microwave that has a rack inside which gives you options other than using the rotating plate inside. Overall it works quite well. I did not purchase this microwave, it came with the apartment. Not sure if I would purchase this brand if I were to buy it for my own home.

I have a GE over the range microwave oven purchased in 2011. 4 years old, hardly out of its service life. In 2013, while heating up my lunch, I heard a loud buzzing and popping noise. The plastic hooks that hold up a metal tray (yes, the unit comes with a metal tray) in the microwave oven caught fire. I called GE and demanded they repair the unit, they said they were not responsible since it was out of the warranty period. Having experience in the insurance industry, I reminded them about product liability, if this is a common occurrence, there would be potential liability issues for GE. The service tech said they would send someone out free of charge to repair the unit. He replaced the two hooks that fried and said they were no longer responsible for unit. Today, 01/28/15, we just had it happen again. One more hook caught fire. Hey GE, do you really think I will buy any kind of appliance from you again when you make a defective product and dont stand behind it? I will not. I would recommend people do your research carefully when buying a microwave oven, especially one from GE. I would recommend anyone do research when buying any kind of GE product since, in my opinion, they clearly do not care about their customers.

Over-the-range microwave failure (model JVM2052, manufactured Dec. 2010) was purchased and installed professionally in March 2011. Total cost is $546. First, the fan failed in about June 2012 and I thought I can live with this. In Sept. 2012, the unit failed, but the interior light and clock still work. I paid $97.00 for a service call from the dealer, and the tech said the power source failed(?). Estimated parts and labor for repair is $370. So, I will buy a new unit (not GE) and pay about $150 for delivery and installation and take away this GE unit. I live in Morris County, NJ and this is not a rural area! GE service rep whom I called said GE doesnt service this area and to look in the yellow pages for an authorized dealer. I called again and got the name and address of the president of GE Appliances, and I am going to write about this product.

We selected this microwave because it has a toaster and baking feature as our small kitchen would be better without a toaster oven taking up space. Turns out user must change accessories from glass to metal when using the toaster and baking feature. The space needed to store accessories rendered the space saving concept as useless. Also, the toasting is slow and does not quite equal what a toaster oven accomplishes. Also the baking/convection mode is so noisy, one cannot hear radio/tv. 30 minutes for a baked potato is a long time for excessive noise. We bought from Kitchen Solutions in the Bronx about May 2014.

I purchased a GE dishwasher model GSD2100v50BB on June 6, 2016. By March 9, 2017, a switch broke which caused the machine to be stuck in the wash cycle for over an hour before it was discovered. This caused soapy water to flow out of the machine all over the floor. It was fixed under warranty but by June 29, 2017 it broke again. It is no longer under warranty and it will cost $70 to 100 to fix it again. It was purchased at Home Depot and they state it is to be handled by GE. GE states that since a year has elapsed, they are not responsible for the repair.

I bought the GE microwave from a GE dealer. We were very impressed that it is also a convection oven. It bakes, microwaves and even toasts bread. The oven had not disappointed us any way. I would recommend it to anyone in the market for a microwave.

I have a GE Triton. We started a load of dishes before going to bed. When we woke up in the morning there was a terrible burning plastic smell. The dishwasher was stuck on, and ran all night. It wouldnt turn off, so we unplugged it. We are lucky that it didnt catch the house on fire. NEVER go to sleep with your dishwasher running. All the stuff you see at the bottom is plastic that dripped down. It melted the bottom of the silverware rack, and some silverware fell down to the bottom where the plastic handles of the knife handles melted. There is brown residue, so I think it did start to catch fire. Thank goodness we woke up early.

GE DE68 00307A microwave was bought in June of 2011. Last weekend, August 25, I was heating water and the microwave started smoking and then failed. The entire apartment was filled with chemical smelling smoke. I have a parrot and had to get her out immediately as this type of smoke is highly toxic. I had to keep her out all night long.

2 year old GE ADORA dishwasher - I am so disturbed tonight after seeing what happened to the protection rubber that is on the exterior of my dishwasher. I decided to buy a new dishwasher because the bottom tray would not stop when pulled out at the correct stopping point. Today I got my new dishwasher installed and when the installers pulled the old one out I was shocked to see that the protectant that I would assume was placed to protect my house was melted all over my wall behind the dishwasher. WOW. Talk about a MAJOR fire hazard. Thank God my house didnt catch on fire because of this faulty equipment. Check out my pictures and you will see the pile of protectant that was under, on my wall, and behind the dishwasher once it was pulled out. Sincerely concerned.

I am writing this more as an educational notice for consumers of the G.E./Rheem gas water heaters to aid in uninterrupted service and understanding of the water heater. Installation locations: If you have installed your unit outside, all though in the owner’s manual, it states that G.E./Rheem says to never install the unit outside. People that live in warm climates do have their unit installed as such, but in a metal enclosure, of which to the city codes are fine, but again not by the G.E./Rheem standards. So being as this is accepted by city codes, people do and will continue to install water heater outside in enclosures.

Model JVM1740DP1BB - GE Microwave - complaining since November 2014. Great microwave UNTIL the inside ceiling bubbled and began to flake off in various locations. A service tech that visited our home advised us to call GE and advise them of a potentially hazardous situation. The GE rep offered to sell us a new microwave but only stated that we were out of warranty, although this is clearly a manufacturers defect! She proceeded to tell us the lining was perfectly safe but maybe we shouldnt operate it. I have written GE management to see if they will assist in replacing the defective unit; GE is the reason we purchased it to begin with (but it may be the reason never to purchase one again).

My less than a year old GE microwave stopped working last week. My AT&T phone service died so I had to make repair arrangements online. Guy was here this morning. My microwave’s main board is fried. It does not conform to Repair Guy’s published schematics. Repair Tech could not upload new data to it. Repair guy did order three new parts including a main board. GE told Repair Guy that mainboard delivery ETA UNKNOWN. After three hours here repair tech left and told me to call GE customer care. Believe it or not, two hours on telephone with GE. First you need to talk to a customer service rep that cannot help you. They then determine you need a Customer Advocate. Then they need to input data on your file for the Customer Advocate.Then they need to transfer you to that department. Then you have to get a case number assigned. Then you give someone all the serial numbers and model numbers again. Then the Customer Advocate (CA) takes the call. The CA does not speak English as you and I speak English. After the CA puts me on hold to verify the purchase, then the appointment, then the tech and then the order they actually speak to me. In my case, the mainboard part is not available on CA’s computer. The CA has to electronically contact the parts department to find out if the part is in this universe. If the part can be delivered to my Repair Guy in Jackson, GA within 14 BUSINESS days from the date of the inquiry I have to take the part and wait for repair.In the event the part cannot be delivered in 14 days CA will start a process to get me a new microwave. The parts department has up to 48 hours to respond to the CA. When asked what happens if no response occurs in 48 hours, I was told, That never happens. It is the Christmas Holiday and I anticipated guests. My husband is disabled and his meals are pre-made frozen so I will have to decompose them and heat them on the cooktop. GE could care less about those issues. So after waiting five days for repair I have no working microwave. Someone told me not to replace my GE with a GE, but I did not listen. It is December, holidays, no microwave is an aggravation that I thought paying for a GE product would alleviate. So, on January 2nd I might get an answer. Part possible or new appliance COULD be ordered and delivered by someone sometime.

I bought this dishwasher GLDT690TBB-00 on 05/12. Its not even 2 yrs old. I had some minor complaints about how hard it was to fit bowls, how the utensil rack wasnt easily accessible, how long the cycles took, how it had to be vented right after a cycle to keep clean dishes from smelling musty... But I was willing to put up with that. I spent about $700 new. The dishes did come out clean, if I stacked them properly. I only used it when full, about 2x/week, as I am an aging widow & live alone. It stopped functioning a few days ago. Control panel lit up, a little water came in, but no action with spray, etc. Called a local repair company today. They say the control panel is shorted out, and that in turn burned out the motor. The repair cost would have been $524.61. REALLY? Not doing that! Very disgusted. Ill never buy GE again. Last KitchenAid lasted 12 yrs, but as all the repair guys say: They dont make em like they used to! Too many bells & whistles. All I require is clean dishes, and for the appliance to do its job.

My dishwasher is a GE Profile. It is as quiet as a Bosch we had in another home we had but it must cost half as much. We have it 8 years now- no problems. Never had a service call or anything wrong with it. It owes us nothing.

I replaced a GE JEM25 microwave when the Magnetron gave up with a PEM31DWW unit. Within 14 months the paint on the ceiling of the oven started flaking off. Contacted GE and they offered to sell me another oven for $166. After reading all the negative reviews on this site, I dont think I will ever buy another GE product.

Since 2010, our 2006 GE 1.1 cu. ft. countertop microwave oven model # JES1136WL has had power failure problems. It began in our previous home and now in our next home. All of a sudden, Id check the panel and it would say PF, which means power failure. So, Id reset the clock and there it is, ready for the next usage. Over a year later, in our new home, as of yesterday, it will start and immediately cut off. Now, weve been using this microwave in the same plug since May and now its October. So, what happened? Today, Im looking for the users manual and have located it online. But it appears that the PDF GE has for it, the Adobe document, has a problem. So, Im going to check it on my laptop, as this is my PC. Thank God we only paid under $100 for it. On some of these consumer complaint stories, the person paid a great deal for theirs.

This dishwasher is cheaply constructed with a plastic interior. It is so loud that we run it when we are away. Its impossible to watch TV while this thing is running. Also the dishes come out with a film on them. Not happy with the low grade appliance at all.

Our stainless steel finish 1100 watt JES1142 microwave is around 2 years old. Within the last year the finish inside started to corrode (yes, my wife cleaned it regularly with a non abrasive, appropriate cleanser). Also, the door latch button started sticking and a few days ago it just stopped heating. Unfortunately I cant find my receipt, but I bought it at my local Lowes on Bell Rd. Nashville TN. Serial # is MA212483G. Manufactured July 2013. Was this just a lemon? Very disappointed.

I bought a 1.6 cu ft microwave at Christmas, microwave failed within a month (electric burning smell and microwave quit). Contacted GE to replace and was given a run around (told to buy first, send them the receipt, then they sent a check). Finally they replaced now - have the same issue with the new one. Never buy a GE appliance, I certainly will not!!

I was washing the inside of my microwave and noticed that paint was peeling off the top. It looked like paper. Reading the other comments on the same problem I knew it would do any good to contact GE. GE products have always been inferior to other brands in the market.

I got a GE cafe two years ago, all the matching appliances. A few weeks ago, we heard beeping in the middle of the night. ow every night at two am we get a message on the panel with annoying beeping. This weekend, we went out of town and when we returned the microwave was and had been on for a very long time. It doesnt take a genius to figure out that our house could burnt to the ground while we were gone! Thank God it didnt! Not to mention. my dishwasher does not clean! It takes 3 runs to wash.

I purchased a dishwasher from GE 3 months ago and it broke, just stopped working. I called GE. After being on hold for an hour, they scheduled a repair call with At Bay Appliance, gave me a confirmation number and everything. AT BAY dispatch says they never received it and cannot schedule an appointment with me, I have to go through GE. I took the day off of work for this repair!I called GE again and was told to call Consumer Relations who apologized and scheduled a second call with AT BAY, apparently the only company who can repair in the SF Bay Area. Guess what? They say they never received the repair order and that I have to call GE. Again, I took a day off for this repair. What is this? Ive never experienced such poor service in my life.

I remodeled my house 5 years ago and went with the GE Profile appliances in my kitchen. Last week I had run the dish washer cycle and noticed the soap had not dissolved and the dishes didnt seem to be clean so I ran the cycle again. I started it at about 8 pm and we went to bed not thinking any more about it. About 1 am I awoke to a horrible plastic burning smell. I checked through the whole house and could not find where it was coming from until I entered the kitchen. As I entered the room my eyes started streaming from the burn. I opened the dishwasher and smoke starting bellowing out of it. Not just smoke but a toxic smoke filled the room. The inside of the dishwasher was so hot and everything plastic inside was melted. The bottom drawer and parts of the dishwasher were also melted. The silverware tray full of silverware was all melted together. This all occurred in a matter of 5 hours. Had I not woke up when I did, who knows if we would have woke up.The house was full of toxic smoke that did not trigger the smoke detectors. We just went ahead and purchased a new dishwasher and had it installed yesterday. This morning my husband decided to do a little research on this product and found there was a recall last year. I contacted GE and found that our model was not part of the recall because it has a stainless steel interior, only the plastic interiors are part of the recall. I also found out that had we called them and had them send out a certified GE technician look at it, they would replace it. Too late it has already been replaced and sent to the recycle center. I did take pictures and have record of the model and serial number which doesnt matter. I just want to get it out there that this product is also dangerous and a fire hazard. This product could have easily caused a fire in my home. I also wish I would have done more research before we replaced it. Our new dishwasher is a GE Profile...

We have had multiple service calls where the tech explains immediately that he knows what the problem is, where there is a very loud buzzing noise as if you were going to be shocked by the microwave if you touch it while it is running. Now after fixing this problem multiple times, having the display burn out, etc. tonight we find out the microwave is actually turning ON when you open the door! This is a severe safety hazard! The interlock is doing exactly the opposite of what it is supposed to do!

A year after I got my GE dishwasher at Home Depot, it warped, protruded into room out of counter. GE tech fastened it into cabinet, agreed warped, said call co. Cust. Serv. Rude, said should have called while in warranty. Offered tiny discount to buy another for $400. Its worse each day.

We had a GE dishwasher installed by the builder when the house we live in was built and it was one of the ones which were recalled as a fire hazard. We didnt really have any issues with it though, other than it was a bit noisy. With the credit offered, we decided to upgrade to a high end Profile model. The sound proofing is impressive and it was actually hard to tell the unit was on, but that is the only thing you can say that is good about the machine. As a dishwasher, it fails miserably and often items come out dirtier than when they went in. OK, weve struggled on with that for some time now but today, a nasty burnt plastic smell brought us both to the kitchen to investigate. Sure enough, the replacement for the fire hazard was the culprit. Obviously, it will need some serious repairs before it is safe to use once more. Looking through this and other sites, it seems this problem is rife and GE is reluctant to deal with the issues. Well I think that will be our last GE appliance. Thank you very much and rather than throw good money after bad, we will put the repair costs towards another machine ABGE.

I have a 15 year old washer/dryer set that has worked consistently and it resides at a rental property. I purchased GE washer/dryer set for primary home 4 years ago and it's awesome. It's the level 1-2 steps above basic model and has enough settings to fit my needs (maybe more than I even use) such as pre-soaking, 4 settings for loads and much more. I would not purchase anything besides GE appliances. Very reliable and easy to interface with.

Our GE microwave just stopped working after 3 or 4 years. It was manufactured 4 years ago, but I am not exactly sure when we purchased and installed it... It may have sat on the shelf for a year. It is not the touch panel, the lights, timer, clock... They all work. In fact, I can put in a time to cook and push START and the timer will start counting down as if the microwave is cooking, but it is totally silent, no turntable, no noise, no nothing. The new replacement model number is the JVM6175 but I am scared to buy it, as I am so disappointed in GE. All the washers, dryers, microwaves, and refrigerators we have bought over the last 30 years have only lasted 3 to 7 years. The only appliance by GE we have purchased that seems to be still working is the dishwasher. We only used this microwave to heat up coffee or some leftovers. It is not being used to cook big meals or anything like that. GE has just gone downhill, it appears. I think I will just give up on them totally.

I have microwaved many types of food in mine! Remember, it’s not just for reheating leftovers! I have cooked fish, and chicken successfully. Those turned out juicy and tender. I follow directions from a microwave cookbook. It’s easy and clean up is a snap.

According to the label in my GE Sensor microwave oven, it was manufactured in October 2010. I dont know how long after that time I purchased it. The paint on the ceiling is falling off and what hasnt fallen off is bubbling up over the entire surface, exposing bare metal. There is also missing paint on the floor of the oven. I called GE today and was told by a representative that it is a fire hazard and I should stop using it. She said I must have used a harsh chemical, but I have used nothing but dish detergent and water on paper towels. There should be a recall of these ovens, and GE needs to improve the quality of the paint. The microwave is not that old, and this should not have happened!

This review is related to the Monogram 2.2 Cu. Ft. Built-In Microwave Oven model #ZEB1227SLSS. The GE site: https://appliances.monogram.com/us/specs/ZEB1227SLSS indicates in two places that the built-in trim kit is included (and one place where it is listed as additional), yet GE has confirmed that in fact, the trim kit is an optional add-on with a $325 additional cost. Calls to GEs consumer line have been disappointing. Me: Your website says its included, and is in a section with other features that are in fact included but not additional fees; GE: We have confirmed that the trim kit costs extra. We have, in fact, purchased the oven and are awaiting its installation, and I have other experience with GE Monogram appliances so I expect this to operate well. But I cannot understand their reluctance to acknowledge this error on their site. Potential buyers, please beware of this issue.

This unit is an over the oven with a vent fan, lights, and is paired with my GE double stove. I bought this microwave was purchased for more reasons than performance. It has been used frequently for over 5 years with no problems. It is easy to use and the food with this model (which has the rotating tray) heats the food evenly. No problems, functions with ease, and dependable.

Generally ok, but the entire wash cycles take way too long. Certainly much longer than the older models. I guess thats more or less the case with most dishwashers today. It makes me hesitant to use the dishwasher when I consider all the energy it takes to function. I would prefer having a setting for speedier rinse/wash of just a few dishes.

My microwave is a very easy to use. The settings are not complicated and offers a variety of options. It has a shelf and turntable that can be shut off and on. The filters are very easy to access and clean.

I bought a new house and within 2 years my GE dishwasher and now my GE microwave jvm1750sp1ss need replaced. Ive got a cheap $100 microwave in the basement thats worked for years. GE quality has apparently went downhill. NEVER again. Cannot believe appliances that cant even last 2 years.

Dishwasher looks and works beautifully. It is slate black and I have never had to redo any dish or glass. It is located. About 12’ from our bedroom door and we turn in on before go to bed. It is so quiet that we never have our sleep disturbed.

All GE kitchen appliances delivered on time, but the dishwasher has been a nightmare. Started leaking right away, called GE and they couldnt come back out for 3 whole days after installing it, which ended up being a work day - so had to miss work to wait all day when he didnt come until 5 pm. Tried to make us pay for the service - we havent even used the dishwasher and they think we are going to pay them to come out fix their mistake, also under a 1 year warranty. Tech guy came out ran some computer test - didnt even look at the dishwasher or underneath. Test was good, we asked him to stay a few extra minutes and he said thats not his job. Leaked again. GE argued that we didnt get it installed by them, which was a lie. Same tech guy came out again, on a workday Again so missed work - finally figured out what was wrong, ordered the part. The part wasnt coming in for another week. So we Waited Another week without a dishwasher.When that day came We again missed work because they said between 1-5 and didnt even show up. GE tried to say the part wasnt in but we were holding the part when we asked where they were. Infuriating at that point already missed so much work days and GE employees couldnt even do their job. GE rescheduled the appointment without even telling us. Had to wait another week until they finally came out and fixed the dishwasher. Now almost a month after they delivered the appliances, I received a charge and didnt not even email to let us know we were being charged. Horrible experience with GE and will never ever buy from them again.

The GE MICROWAVE MODEL JVM6175EF1ES was manufactured in August 2015. I purchased it in November of 2015, brand new from Home Depot. It was not installed until April 2016. So less than 2 years after installation it malfunctioned. (The unit brand new only has a 1 year warranty). The parts the tech replaced have a 5 year warranty. That demonstrates to me that GE does not have a lot of faith in their appliances. Aside from that I paid $375 for the repair, thats almost the price of a new microwave. But I paid since it made more sense to have a 5 year warranty on the parts instead of a 1 year with a brand new unit. I WILL NOT be buying GE products in the future due to this product defect.

I bought GE dishwasher model #GDF570SGJOCC from a local appliance dealer in April, 2017. The machine cost about $600, and $150 to install. Today I learned the circuit board is caput and it will cost $600 to replace it. I will never again buy a GE product-- 2 years of service and it needs to be replaced.

This dishwasher was brand new in our new house. It didnt work right from day one. GE service came out 3 times to repair. The first 2 times the GE tech was here all of 5-10 minutes and didnt repair it either. The 3rd time the tech actually pulled out the dishwasher and found the problem and fixed it. Their customer service was terrible.

I purchased a GDF520PGJ dishwasher from Home Depot and it still doesnt work. Home Depot has no return policy and G.E. has been unable to resolve. I have written to GE Appliances Consumer Relations for a replacement but pending another service call. Its unfortunate that there is no recourse with Home Depot as was advised that I need to work with GE for the first year warranty yet my dishwasher hasnt worked for the past month. Buyer beware.

Have had dishwasher for 3 years and it quit working. Had appliance repair people out 3 times and they replaced every circuit board and harness in dishwasher as per GE and still doesnt work. GE own techncians dont even know how to fix it. So I am replacing it! No more GE appliances for me!

I just renovated my kitchen and purchased all new appliances. I had stopped buying anything GE because of the poor customer service and inferior appliances. After more than 25 years I thought I would give GE a second chance. What a mistake. My new microwave clunks every time the dish inside spins. GE sent out a repairman who said he fixed it. As soon as he walked out the door, I realized it was never fixed correctly. After waiting on hold with GE for over 45 minutes today, I was told that they will send another repairman out. If he finds it isnt repairable then he will send that info back to GE who will try and figure out how to fix it. If it cant be fixed then I will get a new microwave. It is a new microwave that was defective. I dont want this microwave because it has been defective since day one. I purchased my appliances from a local family owned store. GE has a policy that they (GE), are responsible for repairs for the first year and then the company I purchased the appliances from will do any future repairs. I will never buy another appliance from GE. They still have the worst customer service. Ridiculous how terribly they stand behind their appliances.

We purchased our GE dishwasher in September 2014. In December 2014 the dishwasher started to make a loud grinding noise. I contacted GE and a repair man was sent promptly to do the repair. Upon arrival and looking at the dishwasher he advised me that it was the motor. He then stated that he would order the parts and also stated that he did not have the correct tool to remove the motor and has not had one since they have changed the manufacturing process. At this time I am still waiting for the parts and I have contacted GE numerous times to find that the parts were either on back order or had been shipped out. I am still waiting for the parts and the repairs to be done. The estimated date of the parts to arrive is January 29th. At that time I will have been without a dishwasher for a month that I have just purchased.

Month Long Dish Washer Installation from Hell (Try #3 the best).Install Try 1 (I took off work for): Oops, I ordered the wrong hose. I am going to have to come back next week to install. I will call you and set something up. (installer). Next week Friday: Hello is this GE Installation services Umm its Friday and the guy never called or showed up this week to install my dishwasher I just purchased??!? (me). We then set up a time for the following week. How unprofessional.Install Try 2 (I took off work for): Umm still didnt bring the right hose. Can you go to Home Depot for me and buy the right one and bring it back? (installer). Ahh No!?! This is your problem not mine. (me). Well I will have to come back then. (installer). You have to be kidding me. I have to take another day off work?!? (me). Finally he gets a guy to come with the correct hose. Umm, can I borrow a screw driver and some tools from you?(installer). You have to be kidding me, sure? (me). Installer proceeds to drop the sides and fumble around banging the pieces on my NEW floor. Finally getting it installed. It doesnt look right. Dont the feet raise up and shouldnt the dishwasher be flush to the cabinets????!? and it looks crooked?? (me). Nope. (installer). I file a complaint and the guy removes my $60 install fee and sends another team out to fix it.Install Try 3 (I took off work for): 3 guys come and re-install dishwasher worse than the guy before them. From the other room you hear banging around and Oops, I broke a screw etc... This is what happens afterwards. Umm the plastic backing and sides are showing. Its pushed out farther than it was from the first guy. It definitely is NOT supposed to look like that. Plus its loose??? (me). Best we can do. Bye. (install team). This doesnt seem right....(me). Oh no, its leaking!!!!!!!!!!!! (me). So I called a plumber to come ASAP as I said before its NEW wood floor. New Plumber NOT associated with GE or Home Depot (who I probably will be getting a nice bill for calling last minute) proceeds to fix my dishwasher for the next 4 hours...Here is a small list of problems: 1) its leaking; 2) the foot vibrated off; 3) screws broke off; 4) damage to hose; 5) bottom plate installed at angle not even remotely level; 6) scratched up floor and cabinets; 7) installed too far forward and too low. This is the list. So far we still are trying to figure out where it is leaking from and if the dishwasher even will work. Thank god I actually got a Professional this time unlike GE/Home Depots teams. I then called GE Install services 1-800-432-7167 again and this is what they had to say: We already refunded you the 60 dollars. There is nothing we can do but we will file your complaint. I called again to speak with a manager and after a long conversation, he gave me $62 off my order. -- And let me tell you that is not going to cover the cost of the plumber I just hired to fix your mess. Not to mention the 3 days off work I took. Irritated I hung up. I bought a fridge, cook top, and double oven with GE along with this dishwasher. I wish I hadnt given them my business. Apparently, I am supposed to call back if the dishwasher doesnt work when my plumber is done working on it. Oh I WILL be calling back, you can bet on it. As for now I just hope he finds the leak... Moral of the story is NEVER use the install services they offer. You are better off getting your own plumber from the start.

I have a GE Profile model JT965SK4SS micro/oven combo. It came new with my new home. A couple years into it, the paint (lining) interior of the microwave start to bubble and peel and eventually started rusting. Had SEARS come out (warranty had expired) who contacted GE and they concluded it was only cosmetic that it doesnt affect the functioning of the microwave. Well, its gotten a LOT WORSE now, bubbled peeling paint all over inside, rust, exposed metal, and the paint is falling onto food. I can NOT even wipe out the interior to clean it, it makes more stuff come off/fall down. I called GE last week, was told by 2 employees that it is NOT safe to use anymore, discontinue use. I had SEARS come again (per GE). The tech said he had NEVER seen anything like it before. He called GE to tell them its not safe, exposed metal, and its dangerous. They again said, well maam, youve gotten 8 years use of it. We wont replace it, but will offer you a discount for a new one ($2,500 out of pocket for me). The person who had offered me the discount (yes, I sent pictures, showed how bad it is) also gave me a tip regarding the unit I have now with the exposed metal and the chance of arcing (spelled? like Ark) if the unit catches on fire, make sure not to open the doors, the fire should contain itself. 2 employees told me its not safe, a 3rd gave me helpful info for if/when it catches on fire... and yet, they still wont replace the unit... and do not stand behind their own products. I plan to go to our local news station, see if they can get anywhere with this, since they wont do anything. Patiently waiting and unable to afford a new unit.

We have a GE profile dishwasher for about 14 months. I just found out last week that its out of warranty and that the 2 circuit boards inside are bad so the tech came out and didnt have a replacement board on his truck saying they never have problems with this dishwasher so hell order this part and be shipped to my house. He would install it on the following Thursday so Im sitting here waiting for service. I finally called to find out that GE decided that it is going to be repaired on Friday. I did not know this of course so I asked for a supervisor. I was put on hold with no answers, finally hung up in disgust.

My Microwave oven is 22 years old. It still works fine, but does not have power levels on it. The reheat is vague and I have to keep checking so things dont burn or dry up. The dishes get very hot after about only three minutes. Other than that, it is easy to clean and still looks good.

Door would not latch, so entire locking mechanism was replaced. Still wont lock. Repairman said it looks like door is warped or bent and door may need to be replaced. We have used the dishwasher twice a week for a year and suddenly it wont lock. Have heard this is a common issue. Is this true? Is there a recall?

I bought a GE 1750 microwave in May 2011, which got caught on fire last March 2, 2012. Now, we have to go through all the hassles of having a repair tech come out and probably be without a microwave for months!

Dont buy one. I bought two last year. The first one completely died before the 60 days were up. I took it back to Sams club and bought another. The tag inside says it was made February 2011, so its only a year and a half old. Under the carousel, the paint is peeling big time. I wrote GE repeatedly, asking if it was still ok to use it. After ignoring me for quite some time, I got this reply. In the notice, they told me to get Sams club to replace the defective and apparently unusable product they are selling knowing it is defective. I love the part where you cant cook something with too much liquid in it. Who does that when they microwave?Heres what they said: Thank you for contacting GE regarding your microwaves and the paint peeling issue. I did some research on it and found that it a common issue among all brands. Excessive heating of un-covered liquids can create a high amount of condensation that the inside paint is not meant to withstand. Minor chips to the coating on the microwaves interior cavity will not affect the products performance. However, if the coating is actively flaking or peeling anywhere inside the oven cavity (including under the turntable), discontinue the use of the microwave and replace it. GE does not have an approved method of repair, and the microwave is not repairable. Please return to Sams club for an exchange, if you are still within the one year warranty. If Sams is refusing to accept the return, contact the Sams Club Support Team at 1-877-885-2787. GE will then reimburse Sams club.

We installed a GE Spacemaker Microwave Oven /Range Hood in 2005. We used it mainly for the overhead light over the range, the timer, the vent fan, and only occasionally to microwave vegetables. On 8/5/2011, I put a dish of eggplant in a glass dish to heat up and the microwave shut down completely to the point that I had to check the circuit breaker to see if the switch was shut off. The microwave and everything associated with it is dead.

My prior GE ref was 13 years old. New one, now four months old, has cut my electric bill by 40%, runs much more quietly. It is a 15.3 cu feet side-by-side; the top area of the refer side has a bulky light cover that interferes with what you can put on the top shelf. The pockets on the inside door of the freezer side are a bit too small. But, all things considered, it's a great unit and I'd probably buy it again, considering the price.

Our GE microwave, manufactured in 2012, has been running fine, but the door handle has cracked on the bottom. Imagine my shock when I found the cheapest price for a PLASTIC handle was well over $100. How can this be?

The GE repairman just left. It wasnt the coil that was flaking, it was the eco dish washing detergent I was using. The detergent wasnt dissolving, it was clogging up the jets and burning on the coil. What I was seeing was black burned detergent flakes. The repairman gave me citric acid to use to clean out the clogs (for free). He also didnt charge me for the visit, even though it was my fault. He also told me to get the water in my sink really hot before I start the dishwasher. I am very impressed with his service!

GLDT696 series dishwasher - I have put up with my GE appliances and their problems for years, but now I will throw in the towel. Our Contractor appliances were replaced 5 years ago when remodeling the kitchen. Ten years of no problems with cheap stuff replaced with Stainless Steel GE ovens, fridge, microwave and dishwasher. I will only mention the dishwasher in this posting. Bottom line... Wish I went with another manufacturer. The washer has a gasket that loves to fall out of place creating leaks or floods. The pump has failed after the one year warranty. The control board has been replaced twice and today it looks like there will be a third one. That is if I am stupid enough to hold on to this piece of junk. If I buy another manufacturers steel front dishwasher it will not match the other appliances. At this point I dont care. Unlikely to ever buy a GE appliance again.

Enamel curdles and becomes unattached from the ceilings of the interior of the microwave. Family member purchased 3-yr. newer model and the same thing happened. Theirs makes a terrible noise while cooking! Inferior product - inferior, unreliable materials!!! No accountability or sign of improvement! I will never buy a GE product again.

We have an overhead microwave that fits nicely into the spot. The power level seems to have dropped off, but this is after more than 8 years with lots of daily usage.

I purchased a GE monogram microwave along with all the other brand new appliances when I remodeled my kitchen. Let me be clear when I say I will never buy another GE product again in my life. Not only is the product inferior but the customer service department is run by a group of very inept people that lack basic communication skills. The microwave I purchased needed two repairs within the first five years of purchase. I have a microwave in my office at work that I purchased over 10 years ago and Ive never had an issue with it. Needless to say, it isnt a GE product. Last April the microwave started acting up again and kept turning itself off. We didnt even bother calling GE because like everything else their repairmen are also incompetent. 1-800-Appliance came out and found that the magnetron needed to be replaced and we should just purchase a new appliance. Because our microwave had been installed in a custom made cabinet and the trim kit was still good, we made the mistake of purchasing the same exact microwave from GE for convenience. This was in April of 2014. Right now I am waiting for a GE repairman to come and take a look at it because it is already not working. This is after I spent an hour on the phone with consumer relations. I will never purchase a GE product again.

Just bought a Monogram dishwasher one week ago, and the front sound barrier fell off. The service man came out, took a look, and said it was not a big deal. I questioned him why it fell off within such a short period. He stated that it was GEs policy: to make Monogram quieter than competitors, they put in sound barrier in front. However, it fell off often. Since it does not affect how the dishwasher work, GE does not believe that it is a big deal. Therefore, no need for quality control, and he will use new glue to glue it back. No guarantee that it will not fall off later... What is GE stand on the engineering products any more? Will never buy any more GE product...

Bought a new home. GE appliances came with our purchase so it was not our choice. Dishwasher leaked and ruined our wall. Service would not bring us a new dishwasher, they wanted to repair a brand new dishwasher that has multiple problems and damaged our new home. The service guy was such an ASS! Im in my late 30s and this guy was in his 50s and he was acting like one of the mean girls. The dirty looks he gave me! Wow. He said he fixed it, and Im actually running it now. We will see what happens. What junk! I know its going to leak again when we put the new wall in. Especially after reading these reviews!

Purchased a GE profile dishwasher two years ago. It stopped draining. After 4 service calls and $400 we had to buy a new dishwasher. Basically I threw $1000 down the drain. My recommendation is do not buy a GE dishwasher!!!

Ive had a GE model #JKP68G microwave oven for the past 27 years!!! It has been absolutely fantastic!! I love GE products and how reliable they are. Theyre the best!