It doesn’t do the best job of cleaning without rinsing first. Start button is difficult to operate and plastic membrane worn through. Both shelves began rusting within a few years. But no mechanical/electronic issues ever.

We moved into our new manufactured home in May of 2013. That is the month our above range built-in GE microwave was installed. In October of 2013, one of my sons heated a frozen chicken cordon bleu serving for 3 minutes, 45 seconds, according to packaging directions. He said that some of the inside of his food was cool, so my other son put in his serving for four minutes, zero seconds. All of the packaging was removed and each serving was placed on a separate Corelle plate and covered with Glad microwave-safe plastic wrap. While heating the second serving, the microwave started on fire. Fortunately, my son extinguished the fire before it spread. The food did not combust. The fire seems to have started from the ceiling behind the fan. The entire inside of our microwave is clean except for the soot that billowed out from the center of the ceiling. When the service tech came, he scrubbed the soot off of the ceiling with some paper napkins (which he left inside of the unit) and said that the microwave was a total loss. He also said the fire was caused by misuse, because plastic wrap is not meant to be used in the microwave, therefore even though the fire happened within a year of purchase and installation, our warranty was void. I asked GE to get a second opinion and they agreed to send a third party servicer (A&E) who stood me up three times! I finally got to schedule a GE tech to come at the end of December and they sent the same guy who said the fire was our fault! He told me that he never said plastic wrap is not meant for the microwave, but that we are being dishonest because fires only start when the food is left in the microwave for too long. He accidentally let it slip that he is seeing the same problem with GE microwaves in a lot of new construction for student housing in Tallahassee. (We live 20 minutes south of there.) He attempted to recover GEs reputation afterward by saying that of course it was the students faults, too, for misusing the microwave units. Anyway, GE has graciously offered to sell us a new microwave at slight discount. Haha, no thank you!

We purchased a new GE dishwasher from The Brick, after three washes it leaked all over our new hardwood floors. I called The Brick and they said it was GEs problem. I called GE and they sent out a repairman who told us it was a broken seal on the pump and that this dishwasher is discontinued and he cant get the part. So, that would mean GE would have to replace our washer with a new one! We went back to The Brick and told them we did not want the GE washer and wanted to replace it with another brand as we were within the thirty day guarantee. No apology or well pay for the damage to your floor (floor is warped underneath) and guess what Im still waiting for a call back from GE!! Dont buy anything made by GE. You will regret it! As well, I will not be shopping at The Brick anymore.

My GE microwave is not complicated to use. When cooking prepackaged dinners it cooks perfectly in the time the food instructions say it will. I have used other microwaves that the food is over or underdone. No problems with defrosting fruit either. I am very pleased with cost and performance.

My dishwasher is very quiet and effective in its use. I am very pleased with my unit as I saves water and power when in use. It also cleans very well and smells good as it drains completely. General Electric is very reliable and outstanding company and is made in the USA.

We bought our new home 4 years ago & bought upgraded GE Profile appliances. To date, the gas range has been serviced 3 times, the refrigerator too many times to remember & now my dishwasher pump has gone out. We found out the pump just cannot be replaced, but all hoses, etc. must be purchased as well. GE is CRAP & I will never even consider purchasing anything from this company again. Knowing it was bought out a few years ago by Whirlpool (I believe) but still remains under the GE label - consumers BEWARE.

I purchased a GE microwave from Best Buy about a year ago. Every time I wipe it clean, white paint chips come off the inside. This cannot be safe for me or my children. I did contact the company and they were of no help at all. They said that because I heat up liquids in the microwave, this will happen. Duh! I would not recommend purchasing a GE product of any kind (oven, fridge, etc). Their customer service is awful and their products do not last.

Dishwasher lasted just little over a year when it broke down first time. Power switch made out soft plastic jammed up. Next cheaply made door close switch cracked. Part prices are average price. Because poor quality, I predict replacing this within 3-5 years.

Hello to all reading this and considering purchasing a GE dishwasher or other appliance from them. Last June 27th we bought a new home which came with all GE appliances. In fact I have 2 of these dishwashers. Once in the basement (just for low usage) and another one in the kitchen. The first day the dishwasher in the kitchen did not work and they came out and replaced it. I have had 3 other service calls on this thing and now it does not clean. Six days before Thanksgiving. I called and the lady told me no service until November 30th is available. It does not work, the first time they came out it was for a leak, second time the pump was not working and the dishwasher was not draining and now it is not cleaning. It was almost as it was my fault. It is a dishwasher - you put the dishes in and then turn it on and they should come out clean. I should not have to rinse or do anything special to make it work. We spent over 1500 dollars on each of these dishwashers and now one if not working. I did not do anything other than turn it on and expect that it should clean.I was told that they would sell me another dishwasher at a discount. DO YOU REALLY THINK THAT I WOULD EVEN CONSIDER ANOTHER ONE?! A real company should replace this POS and give me another one for free and it has been 15 months and I have had 2 of them in my kitchen. I can tell you if you plan on purchasing look at KitchenAid they run forever without any problems. They also did a fantastic job of support (I had it for 6 years in one house with one repair, second house they never needed to come).

This dishwasher model no. GDL6860N00SS and serial no. DM833394B was purchased in the summer of 2008 and has given me no problems until now. I used it last around 3pm on October 11, 2011 and apparently it was still heating up because my husband noticed a plastic burning smell the next morning. So he opened the dishwasher and it was burning hot! It had my granite countertop scorching hot, it also started to melt the bottle on the top of the counter. I think this could be a manufacturers defect.

Cleans ok but not sure if its detergent or dishwasher but never seems to get all dishes completely clean. It may leave a ring in my tea cup so sometimes Ill have to clean it slightly to make sure it comes off. Basic settings on mine, nothing special. Good for plates and some Pyrex cookware but it would be nice if I could put larger pots in it. Very basic white in color but it is over 10 years old.

Bought brand new GE Profile DW PDT845SSJSS as part of four appliance package to be installed as part of kitchen renovation. Bought in April 2018, renovation delayed until August 2018, install of appliances October 2018, installer by contractor plumber- excellent seasoned experienced installer. Never used DW until moving things into new kitchen. Washed dishes off in DW before placing in cabinets. After 3rd cycle- DW stopped working stating leak detected - contact GE. Are you kidding me? Brand new appliance! We had original installer come out- no leak- no visible water- we went to placed we purchased DW from - local place - Ray’s Appliances- asked for replacement DW. Was told we would have to pay for installation of 2nd DW at 225 charge. Are you kidding me? GE guy came out and did something to DW to fix it but said problem could return... Serious??? Well -DW worked for a few cycles- now displays leak detected again! Called GE and coming out 12/2. Ridiculous- I want a NEW DW with free installation! I’m paying @971 bucks for something that didn’t work from the outset!!!

My microwave is a GE, model JE 1040 made in 1998, which they probably dont make anymore. I use it several times a week, mostly to heat up leftovers and water. Also pre-packaged microwavable meals, such as breakfasts and biscuits. I have cooked different kinds of meat and other items in it many times and am completely satisfied with it. I would be lost without it.

My parents owned the same GE microwave for over 25 years and had no problems with it. However, after theirs finally died 2-3 years ago, my parents made the mistake of purchasing another GE microwave. BIG MISTAKE!!! It wont turn off unless they unplugging it! They have already paid to have a tech come out to fix it but the problem started again 3 months later. I called 1800GECARES and they said you either need to have a tech come out or we can replace it. I said Do you mean your solution is that my parents who just spent several hundreds of dollars on your defective appliance should spend several more hundreds of dollars to purchase another one from GE? Why did their last one last over 25 years but this one only lasted around 2-3 years? Why dont you stand by your products? Their response was I can connect you to customer service for further help. I said I think Im going to stop wasting my time. and hung up on them. Dont trust the GE name, it doesnt mean what it used to!!!

I purchased my GE profile microwave in 2010 when my kitchen was being redone. I picked it for its style and the GE reputation. So far after 9 years, I hope this wont jinx me, it has been a wise choice. I use it daily.

GE MICROWAVE OVEN MODEL PVM 187osmcoz PROFILE over the range. This is the first time we have purchased an extended warranty. It was purchased October 2010. On December 6 2010, the whole unit was replaced. Then little things continued to occur. The fan would start to run continuously. The circuit board was replaced. That lasted for several months. Then another circuit board was replaced. Less than two weeks ago another circuit board was replaced. Last night at dinner the unit began acting up again. This unit is out of commission for almost a whole week after every break down as we wait for parts. While waiting for parts on Jan 24 2012 we bought a Sunbeam Microwave for $39.95 as a back up. I placed it in service today, Jan 29 2013.

I purchased this product in June 2011 for a summer weekend getaway home. I used it 5 times during that summer. The following summer I didnt use it at all. Summer 2013, I used it and everything seemed fine. That night I heard something and the microwave turned on by itself! Thank goodness I was at the house. I cannot believe this unit has not been recalled yet, as I see other consumers are complaining about the same thing. I keep the unit unplugged all the time. What recourse do I have as a consumer? I have my bill of sale and paid good money for this unit.

Microwave and convection oven together...perfect for heating food or baking. Very easy to operate. G.E.profile. Mounts over the stove with an exhaust fan and lights. Also has a rotating plate in it to heat evenly.

GE is a very reliable name brand with history to back it up. I’ve used their washing machines for years and only changed out once due to newer features. I had Thebes first washer for at least 10 years, maybe a little more. It only needed one part replaced, that was the capacitor, otherwise it was still usable. I am not an in depth handy person but I will read and do my research and found directions doable. Additionally, I found the service help desk very informative and that’s how I discovered it was the capacitor that had gone bad after washing clothes for so many years, and believe me, I did a lot of cycles with my kids and family. I feel I got more than my money's worth. Lastly, I’m still using their products to this day. I may not have the frequency because we are empty nesters but I still believe in their products,

I recently purchased a GE Profile 1.9 microwave oven from Home Depot less than a year ago. Last week I went to remove something that I had cooked and went to close the door and it would not stay shut. I ended up getting some masking tape to try and tape it shut in order to keep the light from staying on and burning out until morning when I could get a better look at it, thinking that it had to be something small that could be taken care of without any problem. Hinge adjustment, something getting in the way that I couldnt see, etc, etc. Wrong! I have been over this door with a fine tooth comb and there is nothing that I can see that is preventing it from staying closed, not only that but according to everything that I have read, I am very lucky that I didnt get fried while trying to figure out if the latching mechanism was functioning correctly. I am not even going to go through the long drawn out process of dealing with GE over this due to the simple fact that I have been there done that with my dishwasher that showed up with the front panel dented a few years back from the factory and I ended up blaming the place that I had purchased it through instead of GE and have since found out by reading other complaints that this seems to be something that is not unusual when it comes to GE appliances. I spent over 1100.00 dollars on the dishwasher and they only replaced the panel instead of giving me a new one, and I have never been satisfied with the way that it operates, and it was a very long and drawn out process and I am just not willing to spend the time again on another one of their products. It is unfortunate that we have entered a time where customer satisfaction means nothing, and the days of caring about having repeat business from a satisfied customer are over. The prices continue to rise on the things that we have become to depend on and cant seem to live without, but the quality and workmanship have not only diminished but also present safety threats. I will never purchase another GE anything and I am looking forward to the day when we all have finally had enough of this and do something that makes these companies stand behind the products that they sell and quits ripping the consumer off. Its rampant across the board no matter what you buy, and there should be laws in place in order to keep it from happening. We have laws for everything else, why not have a couple that protect the consumer and their pocket books.

I know this commonplace complaint, like thousands before me, will head straight into the wind because the world just works in this way: technical support and repairs works as a profit center for a corporation. My GE Profile microwave abruptly failed out of warranty after years of use. The cause was due to a wire burning up inside that had not been loosely connected, said the GE technician, so this was an issue of inadequate quality--not bad enough to cause the microwave to fail quickly but enough to cause failure over time.After taking the microwave out of the built-in cabinet, it only took the technician about 5-8 seconds to find and diagnose the problem, several minutes to get the right part (a wire) from the truck, and a couple of minutes to fix it. The labor charge was $121 for about 7 minutes of repair work, to be liberal with time. (This charge is separate from the charge to come to our home and diagnose the problem.) This prorates to over $1,000/hour for a basic wiring change, which I think is exorbitant. I understand that the technician is a highly trained individual, but this is already reflected in the high labor rate.According to GE, the cost to replace the built-in microwave, which came with a matching stainless steel frame would be $550 if we wanted the new microwave to match the frame at least (but not necessarily the oven, stove, etc.). This is the kind of cost you dont think about when you buy a new home built with matching appliances--well, I didnt. Companies like GE can rationalize all they want about all the overhead associated with servicing a repair call. I can certainly grant them some leeway, but in the end, charging an extra 8 times more an already high labor rate given the time needed to fix the problem is simply price gouging a consumer who has no good recourse. (This is why I pretty much avoid repairing anything, except for my car. Its almost never worth it.)I recently had an experience with an experienced plumber charging an hourly rate of $150, prorated by and rounded up to half-hour increments of work, regardless of difficulty of work. Repairing an appliance should work the same way, and my GE bill would have been halved. Because of such profiteering, I will not consider purchasing a GE appliance in the future. I pray that this microwave doesnt break down again in the coming years due to some other problem. It would be a lot less expensive to just buy a non-matching portable microwave then for $100-$150 than to keep up appearances.To be fair, the woman who fielded my service call was courteous and empathetic. Because the microwave apparently had an electrical burning problem, she previously waived the diagnosis fee. Otherwise, my simple repair would have run several hundred dollars, more than the cost of the microwave. However, she was unwilling to reduce the labor charge, so based on how strongly I felt ripped off, I give GE a star rating overall.

I picked the black GEGSD2100BK GE dishwasher for my co-op. It was cost effective (

Just bought a Monogram dishwasher one week ago, and the front sound barrier fell off. The service man came out, took a look, and said it was not a big deal. I questioned him why it fell off within such a short period. He stated that it was GEs policy: to make Monogram quieter than competitors, they put in sound barrier in front. However, it fell off often. Since it does not affect how the dishwasher work, GE does not believe that it is a big deal. Therefore, no need for quality control, and he will use new glue to glue it back. No guarantee that it will not fall off later... What is GE stand on the engineering products any more? Will never buy any more GE product...

I am writing this more as an educational notice for consumers of the G.E./Rheem gas water heaters to aid in uninterrupted service and understanding of the water heater. Installation locations: If you have installed your unit outside, all though in the owner’s manual, it states that G.E./Rheem says to never install the unit outside. People that live in warm climates do have their unit installed as such, but in a metal enclosure, of which to the city codes are fine, but again not by the G.E./Rheem standards. So being as this is accepted by city codes, people do and will continue to install water heater outside in enclosures.

In January 2010, I bought a sensor cooking microwave oven (Model: JES1460DN1BB Serial #: MS900742B). I paid almost $500.00 for it. Now, in less than two years, the inside is already clipping off so it is dangerous to use. I returned it to the store and was told that the guarantee was good for only one year. So, I would have to pay to have it repaired. My last microwave (before GE) lasted well over 10 years. I always thought that GE was a good company; I guess not. I feel that it is their fault. I seldom use the microwave and I even clean it with a damp cloth. I do not think that I should have to pay for the repairs and I should be given some kind of a discount on a new one. I feel that GE is now in the business of making effective appliances. They should stand behind what they make.

I also bought a stove as well as the dishwasher. We Told them with great concern to put a extra warranty on the more expensive item, which was the dish washer... more could go wrong. We all agreed, including sales person. Day before the first year, the dish washer was not draining good. They said the warranty was running out. I told them, I had got extra yr warranty. The robot voice said it might be over. The repairman came in, and said the same thing. The repairman replaced everything in the dishwasher. It took him 3 visits. He got it working. He claimed there was an extra orange ball in the part and that why it didnt drain well.I started using it for 2 weeks and it stop draining completely. When I bought it the salesperson said, See I added the extra warranty on. But unbeknownst to me, she put it on the stove... How the heck am I supposed to know she did it wrong. I call the company and they said, Look at your receipt. And sure enough, it was on the stove. Looking at it and how the salesperson made it sound, it was understood by all that the warranty was on and I had an extra yr on the dishwasher... I looked at the receipt. Had a list of what I bought the warranty and we were good to go. Everything was replaced in it, everything. It was a mechanical issue and yet here it sits not working and I havent even paid for it. I am disabled and was give a lemon. I would never recommend a GE anything. This was a first... I usually buy Whirlpool and never ever had a problem... Theyre selling lemons and they know it.

I purchased a jes1451dn1bb microwave 16 months ago and I just noticed the enamel coating on the top of the unit is chipping. GE has been unhelpful, saying it is outside the warranty and I need to mail the cord and sticker inside it to have a rebate issued. Since I use my microwave daily, I cannot wait until it is processed to buy a new unit. Not only did the product endanger us with exposing our food to paint emissions, the company has been unhelpful. I highly recommend buying another companys product and do your research!

It works really well and this price point is good. It’s lasted me a few years and it is still in new condition. It has a nice modern look also. Good microwave for a great value.

We bought a new GE microwave oven in 2007. It failed in 2018 after much, much use. We replaced it with a Whirlpool which failed in one week. Lowe’s let us return it and we bought another GE like our original and we are very happy with it.

I recently purchased an Adora dishwasher from Home Depot. The price was enough to suggest that it should be a good dishwasher, but its the worst dishwasher Ive ever owned. It does not clean dishes and it takes two hours to do it.

This is one hell of a dish washing machine. You really need to think about getting in on this thing at the ground level. You put the dishes in dirty and they come clean! Holy**!

We have had to repair new appliances, the fridge and the dishwasher. The ice maker doesnt work and the water flows only when it feels like it. We paid good money for the Profile models in the new home. There were four repairs before these mentioned. Now we refuse to fix them any more. We will buy another brand next. We would never recommend this to anyone. Its sad for the company to produce such problem appliances for people. Obviously, they are not interested in repeat business. Now, there is this recall! It is annoying!

Ive been battling this dishwasher since it arrived 9 years-ago. It was a warranty replacement we were stuck with from GE. Plus, we paid $300. We could never get it to clean dishes, no matter how we loaded it or what we used, so we gave up and hand washed dishes for years. This year, I am committed to getting the dishwasher working because of hand eczema. I took it apart and cleaned the sprayer arms, filter & wiped it down completely. I also ran a dishwasher cleaner through it. I finally got it to clean dishes, but only if they are thoroughly rinsed first and on the Pots/Pans setting. After a month, it stopped cleaning my dishes again. I took apart the dishwasher again, and cleaned everything. Now, glasses on the upper rack in the back are not all getting clean. I never overload it. Im convinced that GE Dishwashers are just junk. Someday, Id love to find a dishwasher that actually works. :-( Frustrated!!!

Its a over the range model & came with a house purchase. It’s worked flawlessly for over 5 years now - even after being left with no air conditioning in FL for months on end. The only thing I could think to make it better is making it easier to choose longer length cook times. Button for half min & dial for all the rest can be irritating for your 16 min food.

We moved into our home just over a year ago. We replaced all of the kitchen appliances; refrigerator, stove, microwave, and dishwasher with GE slate gray appliances. This was in November, 2014. On New Years eve (2016), the dishwasher flooded the kitchen. I removed the kick panel and saw water pouring from the pump. After the holiday, we finally got in touch with the appliance repair shop who handles GE warranty work in our area.They contacted GE on our behalf to see if GE would stand behind a product that was just over 1 month out of warranty. Bear in mind, this wasnt something simple like an indicator light burning out, this failure was catastrophic. GE basically told them (and us) to pound sand. We are a 2 person family. The dishwasher was used maybe twice a week during the year weve owned it. Amazing quality! Now Im looking forward to watching the rest of this stuff fall apart. It looks like the life span of the product and the warranty period are the same. How handy for GE. They must not have to depend on repeat business or take these negative reviews seriously.

We bought a GE dishwasher a little over 3 years ago. In the last week of September we awoke to the smell of hot or melted plastic. We found the source to be the dishwasher. I had loaded and started it before going to bed the night before. The counter-top above the dishwasher was stove top hot and upon opening the dishwasher found that a cutting board that we have had for many years and have always put in the dishwasher had melted on top of the heating coil. Dishwasher safe items on the top rack melted as well. It had been drying for at least 9 hours. After pulling the dishwasher out we saw the heat shield had melted and was crumbling. We contacted GE, sent them all the pictures and they told us it was not a safety issue. We have no doubt that if we had not woken up so early we would have had a fire in our house caused by the dishwasher.

We have had our GE microwave for at least five years. We have moved multiple times and had the power go off but through it all, our GE microwave works just as good today as it did when we first bought.

Have had this microwave for about three years, no problems so far. White so it matches our other kitchen appliances. Good size for most uses and easy to clean.

It works great. My microwave is a small white one that has the power to heat or make a dinner. I enjoy using it. I just press how much time I need and the microwave turns on and it either warms up my meal or cooks it.

Has anyone experienced a plastic burning smell when the dishes are drying? My dishwasher is 3 years old and I wash on Light cycle which is suppose to be 45 minutes long but goes for 85 minutes. Company said to turn off circuit breaker and turn back on and it should be fine, it isnt. Last two times I used the dishwasher it wouldnt completely shut down so I had to do it manually and before I did this I could smell a plastic burning smell but there was nothing on the elements. I called for a service call but they were shut down for 4 days.

GE microwave oven (jes1651sj02) started to spark like lightning, which can be seen through the inside vent grid/grill located on the right. Sparks are seen just behind the waveguide cover where the magnetron is located. It seems to be a common problem with GE microwave ovens from what I have researched. The microwave has now stopped working and just makes an odd noise like groan or urrrrr. It’s just over 2 years old. Its a piece of **. It should last 10 years or more, like my last 2 have. I gave away our Sanyo because it wouldnt fit the decor of our new kitchen - wished I never had.

We have the dishwasher, fridge and stove from the GE Cafe series. In the 2 years that we have had them, we have become pretty acquainted with the local repair people because there hasnt been one month when all three were working at the same time. The fridge had to be replaced (we lost over $1000 in just food) - the replacement fridge had to be repaired. The customer service is awful. They are just trained NOT to be helpful. GE takes no responsibility for putting out such low quality, high priced appliances. I will never buy GE again and hopefully these reviews can save you the same grief and hopefully money (we have to pay for service repairs). Buy anything but GE, one star - is one too many!

GLD6560L00SS. My dishwasher (Model number:GLD6560L00SS) was producing large amounts of smoke through the face panel. It filled my kitchen with smoke and produced a strong smell. I contacted GE and they sent a service repairman out and he took a look. He said this problem is very uncommon with this specific unit and he has never seen something like this. After he removed the front panel, we were welcomed by a burnt/charcoal black face-plate. There was an internal fire in the machine. To fast forward I have been working with GE the last 3 weeks and they have offered to cover 50% off a new unit. I cannot afford this even with a discount and they will not cover the cost of a replacement. This problem could have been much worse if I was not home. The house very well could have started on fire. We normally set the unit at night and go to bed... Thank god this was a different day. This kind of thing is unexceptionable and the fact that they will not cover.

I have many other things to do other than to voice my extreme and total displeasure with your company. GE - Huge Company, Small Customer Service. We purchased a GE microwave oven from ABT electronics in about August, 2013. In October, 2014 we had issues with the fan remaining on while the door was closed. Called GE. They said the unit was out of warranty by about 2 months. We felt that was a short period of time and that we called as soon as the issue became chronic.Had three service calls where the techs tried to fix a simple problem. First tech walked through our living room with dirty boots. Didnt fix the problem. Messed up our carpet. Bad attitude. Second call, two techs couldnt fix the problem. Said it was a door issue and they made some superficial adjustments. Problem not fixed. Third call, two more techs. Same result. In the meantime I tried to convince GE that I didnt want another service call. I wanted a new unit. No luck. I was offered a discount to purchase a new unit for around $300 or so. Im sure they spent more money on service calls than a new unit would have cost in terms of dollars and the reputation of one of the worlds biggest companies.Now, the fan for the unit stays on almost all the time after the cooking is done. Is this the best GE can do? If so, thats pretty sad. Tried to reach someone in sales who would get it. No such luck. DONT BUY GE AND IF YOU HAVE ISSUES DONT RELY ON A FACELESS, CLUELESS CUSTOMER SERVICE DEPARTMENT TO HELP IN ANY MEANINGFUL WAY.

We upgraded our appliance package when we bought our village builder home 8 years ago. All GE Monogram appliances have rusted and now need replaced. New liners needed in oven which was so rusted we couldnt get the screws out to replace the originals. Was told by GE customer service rust to be expected when cooking. It creates steam and food particles can cause scratching!!! Maybe it should be steam proof especially a microwave. Even the door on this is rusted! Why the shelf ends in a freezer are rusted not sure on that one! Will NEVER buy this brand again and shame on them my upgraded appliances dont even make it to 10 yrs. A disgrace. My mother just replaced her 20 yr old oven. What is wrong that nowadays things dont last 5 minutes? Shame on you GE not recognizing a definite flaw in your products.

My microwave was purchased 2.13, costing about $500. The panel shorts and I paid for one GE visit, $150. And it happened again. My friend was here and said hers does the same thing. She has a neighbor with the same problem. I researched online and learned quite a bit about this machine. I found out that the panel shorts when youre cooking under it, and steam/heat rises into the machine. Makes the panel short. Im now demanding that GE return $150 service fee that I paid before I found out that its a defective machine. And this machine has to be replaced with a model that allows cooking with vents on. If GE does not do the right thing, I will make it a life goal that no one buy their products. Mark my words. Im this angry because I called customer service this week and was told that theyll give me a new panel but I have to pay for the labor and no refund for the $150 and no replacement microwave. This was insulting. Shame on GE.

This is what transpired on the with GE: I called GE Service because the Magnetron is defective. I had trouble talking to anyone because the Serial Number label on the unit is BLANK. Also, the unit is 9 years old. However, my owners manual reads additional nine-year limited warranty. The customer service rep said the additional warranty is 5 years and GE WILL NOT honor the GE printed manual I have. I was escalated to a supervisor and the first thing she asked for a Serial Number to schedule a service call. I said no, all I want is a new part and she responded cant do that and I cannot schedule a call without a serial number. Hello, the label is BLANK. We went back and forth, getting nowhere and I got angry (I hope can recover the call), she is an IDIOT!Well, opened up the unit and lo and behold it isnt a GE part. I got on eBay and purchased the DAEWOO part (the magnetron the microwave was built with) a lot cheaper and repaired the unit myself. Oh, she said you cant do that. Sounds like Big Brother is alive and well at GE. I dont expect a response since I have been dealt with by the most inhuman people at GE!

I bought a Moffat washer and dryer, and the timer came out of place and burnt on the inside. The timer clips in and if push too hard it will fall out or break the clip. We have extended warranty on it and due the repairman came out twice. The warranty person said it cost more for the repairman than the dryer worth - theres no more warranty. I think the dryer should replace when the timer fell out of place. This dryer should be called back.

New home community - all GE appliances. Model PEB7226SF2SS microwave scorching and catching on fire; GE doesnt stand behind their products and homeowners cant use because products our dangerous (per tech).

I have had this microwave WES1130 for several years now and the paint began peeling before year two. Nearly all of the paint is now gone (fallen into my food). Also, I bought this microwave to replace a larger GE microwave that had failed after only 3 years. The 8-year-old GE fridge is humming loudly and leaks onto my floor, which has ruined the wooden floor and warped it. I will never again buy a GE product, and neither should you. They do not care at all about quality.

GE dishwasher caught fire - not part of recall. I arrived home for lunch to find smoke alarm going off and kitchen hot and hazy. Determined it was dishwasher and opened to thick black smoke pouring out. Heat so extreme cups/dishes and racks and spinning thing on bottom had melted and adhered to elements, each other and bottom. Parts of the dishwasher itself are warped (steel!). Granite countertops too hot to touch and wood cabinetry surrounding it darkened. Dont know the extent of that damage yet. Thank GOD I came home for lunch- I normally do not. I truly believe our house would have been on fire.

DO NOT BUY GE APPLIANCES. The quality is terrible even on an expensive dishwasher. I bought a $700 dishwasher in November 2016 and in April 2017 it was broken, parts not available, but after fighting with customer service, they sent me the parts at my house. No one is available to come over to install the parts, the parts are sitting at my table. I guess they want me to install them myself. I even had purchased a 5-year warranty. Customer service is non existence at General Electric. I know I will never purchase a GE product ever again.

We bought 3 GE Profile appliances in 2005 when we renovated our kitchen. We have not had much problem with the gas oven/range/stove. We have, however, had nothing but problems with the microwave (which I submitted a separate review for) and the dishwasher. Recently, a friend made some suggestions regarding the dishwasher. I then went online and watched some tutorials on troubleshooting my dishwasher problems. I tried all the new suggestions and the dishwasher worked OK the one or two times after that and then back to all the old problems: 1. We have to scour every dish until its nearly clean before loading (even though the instructions specifically stated no pre-rinsing necessary). 2. I am not sure the soap cup opens. The soap is always left caked in the cup resulting in running the dishwasher twice. We have tried all kinds of various soaps and they all do the same thing. The eco-friendly soaps are the worst. We strive to be eco-friendly, but how can we be if we are using the harshest soaps possible AND running our dishwasher twice?! Not to mention the pre-rinse scour and running water until it is 120 degrees prior to running.3. The dishwasher also leaks and is very noisy.I have read some other reviews on this product and realize our dishes are not always dry at the end. This is a non-issue for me. I dont care so much if the dishes are dry. I do prefer for them to be clean. Dishes are a task I do not prefer to do. It would be nice to have a functioning helper. I am grateful the thing hasnt caught on fire. I saw that this dishwasher currently sells for $800-$1,500. I cannot believe it. I wouldnt spend $100 on this piece of junk.

Ahhhh me, here we go again! Its no wonder that the state of business in this country is not as solid as it could be. I purchased your GE dishwasher, Model #GDF540HSF2SS, Serial # ZA703816B, on 01/19/2014 from Lowes Home Centers, 3805 Northern Blvd., Rio Rancho, NM 87124. It was delivered and installed soon after. Soon after that, mid to late July, it began to flood our kitchen. A service call had to be made to replace the tub gaskets. Covered under initial 1 year warranty.Here it is the 5th of November, 2015 and now the unit does not function at all. A service diagnostics call performed today the 6th of November to ascertain its ailment to the tune of $89.00! (No, we didnt purchase the Extended Warranty. My belief has always been that the option to purchase an extended warranty is; 1) an opportunity for the company to make extra money on the sales of a product, and 2) an admission by the manufacturer that the product is probably not well made and will probably break down sometime in the near future!) I guess that future is here for this product! It almost lasted 2 YEARS!! Deplorable! The last dishwasher I had was almost 20 years old and the only service to it was to replace a water hose (which I did myself). Diagnostics proved that the electronic motherboard failed!In addition to the inconvenience and the $89.00, Id be willing to bet that the replacement part for this unit will cost 1/2 of the original purchase price of $599.00! AND I WAS CORRECT; the replacement board will cost $269.00 to replace (part and labor)!!! What a rip-off! I will never purchase another GE product as long as I live! And I will go online and register my opinion and complaint about this product with the Consumer Services Bureau and any place else that I can find to vent electronically!Recently the Sandoval Economic Alliance attempted to lure GE to establish their Headquarters here in New Mexico. For various reasons, we did not make GEs shortlist for consideration. I am thankful that we didnt make it! Why would our state want such a crappy company embarrassing our state with their crappy products? I will be sending a copy of this complaint to them as well.

I purchased my new home equipped with all new G.E. Profile stainless appliances. Three years after that, our microwave (model number JE2160SFS01) had the magnetron go bad - no problem. I called G.E. and had a tech come out and replace it ($79.95). Great! 4 years later, it goes out again. But it’s still covered under warranty (cool). I call them, set up appointment, and ask what the charges will be - $79.95 home service fee. Fantastic! I schedule the appointment, and three days later, a technician comes to my home. I tell him it’s the magnetron, and he turns on the microwave for a second. He says yup and types his diagnosis into his laptop and prints out his estimate. He hands it to me, and it says “Total amount $ 270.10”! On a covered part!I asked him if he was joking, because the M.S.R.P. for that model, which I got from G.E., is... wait for it... $269.00 for the whole microwave oven! I threw the tech out and called their consumer advocate line (which took over an hour to talk to a human) and asked who sets their pricing for repairs, and was told their senior technicians set the labor charges! It’s a twenty-minute job! $190.00 for twenty minutes? So the tech left with $79.95 for doing absolutely nothing! Great job General Electric! I will never buy another product from you again! By the way, the magnetron they say is priced at $142.30 is available online for $97.50! It takes twenty minutes to replace, and a monkey can do it!

I purchased a slate dishwasher in Oct, 2014. After the third cycle the soap would not dispense (door would not open) or the soap dribbled out and remained running down the door. I had to run the cycle twice to get the dishes clean and for the soap to dissolve. I called the store at which it was purchased. A tech came out and replaced a part. Did not work. After the second time, when the tech said nothing was wrong, even though he saw the soap running down the front door, I called GE. They sent a tech from a different store. After the eighth repair I told them I wanted it replaced. They had already replaced the soap dispenser twice, the control board and even told me to move the baskets (ridiculous). They also suggested I run hot water before the cycle! They said if it was repairable they could not replace it.We went back and forth with this and they finally agreed to replace it. Got the new slate dishwasher in July, 2015. After two cycles I started having the exact same issues! I will not deal with GE or ever buy another of their appliances. I will tell everyone I know not to deal with this company. Quality is terrible and service was extremely frustrating, having to take off work numerous times and wait hours for the service person. In the end, it never worked!

Two years ago, after owning a GE JVM1490 microwave-convection oven (over the stove) for three years, the door handle broke.Let me clarify that I worked for GE first as an engineer, later as manager, for 20 years including 6 in Major Appliances. I am ashamed of what I am reading how GE is treating customers today.I am perfectly capable of replacing the handle myself if I am provided the complete and correct assembly drawings and/or instructions. GE refused to provide me anything when I requested them. The scant drawings and instructions I found online are insufficient. As a matter of fact, the design is so poor that removing the internal bezel, which you must do to reach the handle fasteners, forces you to break the mounting tabs, requiring replacement of this part plus the handle. This was confirmed by the parts store I visited.However, even after removing the bezel, neither I nor another ex-GE appliance engineer could figure out the access to the fasteners. I have glued the handle three times using epoxy and Cyanoacrylate (super glue), but it has broken off a fourth time. I will figure out a way of fixing it before I pay GE close to $100 for both the handle and bezel. And if I replace the appliance, you can be sure it will not be GE.GE should be ashamed of the poor design and deplorable customer service they are giving now. How things have changed!My suggestion is that all with this problem post name and phone number of GE customer service personnel they spoke with.

My less than a year old GE microwave stopped working last week. My AT&T phone service died so I had to make repair arrangements online. Guy was here this morning. My microwave’s main board is fried. It does not conform to Repair Guy’s published schematics. Repair Tech could not upload new data to it. Repair guy did order three new parts including a main board. GE told Repair Guy that mainboard delivery ETA UNKNOWN. After three hours here repair tech left and told me to call GE customer care. Believe it or not, two hours on telephone with GE. First you need to talk to a customer service rep that cannot help you. They then determine you need a Customer Advocate. Then they need to input data on your file for the Customer Advocate.Then they need to transfer you to that department. Then you have to get a case number assigned. Then you give someone all the serial numbers and model numbers again. Then the Customer Advocate (CA) takes the call. The CA does not speak English as you and I speak English. After the CA puts me on hold to verify the purchase, then the appointment, then the tech and then the order they actually speak to me. In my case, the mainboard part is not available on CA’s computer. The CA has to electronically contact the parts department to find out if the part is in this universe. If the part can be delivered to my Repair Guy in Jackson, GA within 14 BUSINESS days from the date of the inquiry I have to take the part and wait for repair.In the event the part cannot be delivered in 14 days CA will start a process to get me a new microwave. The parts department has up to 48 hours to respond to the CA. When asked what happens if no response occurs in 48 hours, I was told, That never happens. It is the Christmas Holiday and I anticipated guests. My husband is disabled and his meals are pre-made frozen so I will have to decompose them and heat them on the cooktop. GE could care less about those issues. So after waiting five days for repair I have no working microwave. Someone told me not to replace my GE with a GE, but I did not listen. It is December, holidays, no microwave is an aggravation that I thought paying for a GE product would alleviate. So, on January 2nd I might get an answer. Part possible or new appliance COULD be ordered and delivered by someone sometime.

This washer was easy to install myself, and has worked perfectly. Stainless steel insides. Very happy. You put a pod in, turn it on, cleans great. We do not even have to use heating element. Dishes dry quickly on their own. 24-inch wide. Bought to fit the new kitchen cabinets. Nice brushed stainless outside. Cleans easy with towel and hot water. Silverware container picks up to take to storage areas. No problems at all.

We purchased a GE microwave/convection oven which developed peeling on the inside top of the microwave. GE contacted me and offered a replacement ($300 toward a shelf model or prorate the microwave/oven). Why would we take $300 replacement when we paid nearly $3000 for this oven???? So we took the prorated one directly from GE. We felt confident that we would not have a repeat of the problem. The oven was manufactured in December 2012. After it was delivered, I noticed a rough area on the turntable; and after the oven began to peel AGAIN on the second oven, I believe that the rough area was due to a remanufactured part on the oven.Now we are stuck with another microwave/convection oven combo with the same issues as the first oven. I never used anything harsh to clean the oven and now this happens again. Why cannot this company manufacture an oven that will not have defects in it??? I am tired of peeling paint on a second oven when I have done nothing except pay them for 2 ovens. Why cannot they use stainless steel interiors, and this would stop the many complaints that people make about the product. I would NEVER again purchase another product from this company. The products I have purchased have been inferior. I paid for two microwave/convection ovens and still have one that is inferior!!!!

GE Cafe Series dishwasher model # CDW9380N20SS is a fire hazard. Three days ago, our GE Cafe Series dishwasher nearly caused a fire. If I had not been home that day, it surely would have. I ran the dishwasher as usual and went about my day several hours later. I detected a strange acrid smell and with my five-year-old who was ill and at home that day, discovered the dishwasher door was burning hot to the touch. I needed a potholder to open the door. Once opened, there was a blast of heat and smoke. I needed to use oven mitts to protect my hands from the heat to pull the racks out and handle the dishes. The heating element did not deactivate at the end of the cycle.If I had not been at home, the house would have been destroyed as all the plastic items on the top rack in the dishwasher melted. In addition the plastic parts of the lower rack, the wheels and their clips; the silverware holder; covers; the clips that hold the pot tins in place were destroyed, to the point that the majority of our silverware was coated with plastic. The plastic on the lower water dispenser has been demolished; it completely melted more than 50% of the plastic covering on the arm and is charred and burned. We are so lucky to still have a home!The door must be kept open. When the door is closed, the element super heats and presents a major fire hazard. We have noticed that there is a recall for similar models with plastic tubs, but ours has a stainless tub. GE needs to broaden the recall to include all these models. This is a serious issue that needs to be addressed immediately. Our GE Cafe Series dishwasher model #CDW9380N20SS was installed on October 1, 2008. I would not be surprised to find that parts from the recall in April 2008 were also used in the Cafe Series. I have discovered in the few days since the DW units malfunction that there are over 1000 complaints listed with similar, even identical complaints, on multiple internet sites with the same problems.

We bought a top of the line GE microwave oven (model PEB7226DF1BB sn VA201160N) in 2014. It has now failed 5 times in 4 years - 2015, 2016, twice in 2017 & now 2018 - and the repairs have cost us more than the original price of this piece of junk. We bought it from a local dealer, KAM Appliances in Hyannis, MA, but had to resort to an independent repair service, because KAM was not very responsive. I know that I should have given up on it a long time ago, but in the past I always had good luck with GE appliances. Needless to say, I will never buy anything from GE again. I have learned that GE Appliances are now built by Haier, a Chinese company. No wonder they are junk.

We have a GE SpaceMaker JVM 239BV 001 over the range microwave purchased about 10 years ago. Within one year of installation the handle snapped - just as numerous people here have stated. I went to our local replacement parts store and was shocked that it cost $30 for a new handle. The sales person said if I were you I would by the lifetime warranty for an extra $3 because you will be back, I sell lots of these.

GE microwave model JES1344ES. This is a stainless steel with black accent 1.34 cubic foot microwave oven. It looks great. The micro is heavy for its size. The stainless steel is brushed and low luster finish. The door handle is chrome as is some of the other accent pieces. The push button panel is easy to read and has a large knob for making manual time adjustments. The light inside is very bright. There is a rotating platter in the oven compartment that is not knocked off of its guide rollers very easy. The push button panel is a glossy black material that is easy to attract fingerprints. The preset times that are programmed in the microwave is the only part of the product that could be an issue. For example the popcorn button when used has burnt all of the different brands of microwave popcorn that we have tried. It is set about 30 seconds too long. There is no way to adjust the preset time that I can figure out. We set the time with the large knob manually and the popcorn comes out just fine. The preset times for the Auto Defrost are also a bit off. They are not long enough. We also have a Subzero freezer set at minus 20 degrees Fahrenheit so that may be too cold for the defrost presets. Overall the microwave is great except for the preset times that Ive mentioned. We use it daily and have done so for five years. It still looks excellent inside and out.

We have had our GE dishwasher model GDT580SMF5ES for only 1 year and a half. As I was closing the door the hooks that attached the outer shell/panel to the door broke. Unfortunately we didnt purchase extended warranty so this will not be covered. We have had two technicians from our home insurance coming in but we are not sure yet if the policy will cover the repair. I just cannot believe this is happening as we have barely used this dishwasher as it is only my husband and myself. All I can say is dont buy GE.

I just moved into a senior Community and the GE Dishwasher was already here. I moved from a condo that also came with a dishwasher, a GE, new. It was builder grade and I hated it. But I am really enjoying my GE in my apartment! This one cleans very well and is quiet. I like it a lot.

I purchased a GE dishwasher model no. GLD6700N00CC, serial no. ** about 4 years ago. It just finished the wash, rinse and drying cycle when without warning, the front panel on the dishwasher started smoking and spewing fumes in my kitchen. The front door of the dishwasher and top of my counter were extremely hot. Luckily, I was home when it happened. Otherwise, I might have come home to a fire.

After a short four year history of not cleaning our dishes well, our four-year old GE Profile Quiet Power 6 QP6, model PDW9280N00SS, s/n-VM819634B, overheated and did not shut off and melted everything plastic inside. The house now has a horrible smell of burnt plastic. Ill start the process tomorrow of contacting the insurance company and looking to get this odor out of our home and a different brand of dishwasher into our home.

I love the way the dishwasher is so quiet and cleans the dishes well. However, they are ALWAYS WET. A repairman came and told me that I could not expect the dishes to be dry on the light cycle with the POWER DRY. He told me I have to wash on the normal cycle. I did that and they are still wet. He came back out again and basically had no viable explanation. I have to have a dish towel in hand to dry the dishes as they come out of the dishwasher. I paid a lot of money for what I consider the piece of junk that is sitting in my kitchen. I will never again buy a GE PRODUCT.

Purchased the Maytag MDB7749SBM stainless steel dishwasher in December 2013. The dishwasher and install totaled $700, which for that price and with Maytags past reputation, I wrongly assumed that the dishwasher would last a long time. In May 2016, slightly over 2 years, the dishwasher started having issues with the control panel. The control lock would randomly activate. I would have to reset the circuit breaker daily, leaving it off for around 10 minutes. Even with trying to go through all the steps to resolve the issue, resetting it from the circuit breaker, sequence on the control panel, the dishwasher wouldnt work. I called Maytag and after 40 minutes on hold, they finally answered. They wanted $89 for a service call and for the $143 part, plus labor. Might as well just replace it with another brand like GE, or Samsung.

Have a three-year-old townhouse in New England that came with GE appliances. Within months the microwave needed a new circuit board and, later, the auto open vent is making funny noises when it opens and closes. WORSE: Dishwasher on fritz in third year, requiring a new computer control pad. The cost: $283. American-labeled products produced in other parts of the world are going to cost twice or three times as much before their useful life is over. Shop with care, friends.

We moved into a new home in June of 2011 with the appliances already included. Ours came equipped with a GE, over-the-range microwave, model JVM1540DP1WW, manufactured in Malaysia, in April of 2010. Within several months, the revolving platter began to make a bumping noise while turning and then it eventually quit turning altogether. Five service calls later, we had the platter motor replaced, circuit board and four fan motors (apparently the platter has voltage supplied from that fan to make it run) and it still didnt work.It was taken back to the shop and eventually the problem was traced to a loose wire on a terminal connector. After a month of operation, it is again beginning to make the bumping noise while the platter turns. To top it off, Consumer Reports (the March issue) deals with problematic microwaves, especially the GE model and the unexpected fires that can occur. In addition, they can be susceptible to (not always however and only on certain models) wireless transmissions which could potentially cause them to start on their own. I know for a fact that it knocks off my XM Satellite Radio when it is running. Bottom line...its history and will be replaced with a check rated appliance before I too have a major problem.

I have two of these in my kitchen, just about 3 years old. They have NEVER dried the dishes and I have ALWAYS had to thoroughly wash the dishes because otherwise they dont get clean. One has completely quit working now.

GE Profile Microwave/Convection Oven JVM1790WK, over the range unit, CAUGHT ON FIRE while microwaving water for coffee. One of the four prongs that holds the oven grid in place started flaming wildly and smoking after about one minute of microwaving. My whole kitchen has an acrid awful burning smell. This is my second unit for a small kitchen, and I will be lost without this. The first one I had the handle fell off. This one is too dangerous to use. These units cost $600!!! I cannot afford to replace one every few years. Maybe this model and brand is bad news?

On 05/20/2014, our GE microwave over the stove unit burst into flames. My wife was using timer and walked away then turned around and heard the microwave fan start (spontaneously). Then she observed flames/smoke reflected in the Microwave window. She observed the interior of the microwave was aflame. The fire was extinguished with a rag & water. The burning items appeared to be plastic/insulation. The fan from the microwave was with the burning insulation on the rotating plate. Had this unit only 14 months during that time the microwave fan would turn itself on for 3 minutes and then turn off all by itself. Happened twice in 14 months. Glad we were at home and were able to extinguish the fire. Called Lennar the builder who put this unit in to take pictures and check electrical. Was told the GE unit was bad to call GE. I know this will be a hassle as others have had this same problem with not so good results.

I recently purchased a GD720SGF2WW Serial #HD744674B GE dishwasher. From the moment I tried to use it there was a leak from the bottom of the door. I called for service and when they came the repair man said the door was leaking and there was a repair kit for it so it must be a weak spot in this particular dishwasher, which by the way was not a cheap model and was stainless steel lined. I waited a month for further service and when he finally came he realized he had mistakenly diagnosed the problem and it was a crack in the lining of the door which had gradually gotten bigger as I waited for service. So this NEW dishwasher had been leaking onto my newly installed hardwood floor. By this time I had no faith whatsoever in this dishwasher and said I wanted a replacement. I was called back and told that they would only repair it, which I have been trying to do since NOVEMBER and it is now Jan 21! I will no longer buy GE products and when I called customer service I was on hold for 20 min and finally hung up which Im sure was their intent.

I purchased a full suite of GE Monogram Appliances about 5 years ago. All are fine except the microwave which was made in China. The back is rusting out, the inside is chipping at the door and moisture builds up in the door window. This progressive deterioration has taken place over the past 5 years. I paid $420 for the microwave plus $226 for the trim kit. Now, all GE wants to do is sell me a new unit and a new trim kit (will not fit old trim kit). I paid approximately $20,000 for the entire group. I bought GE because I trusted the name. Im stuck with GE if I want to match the remaining appliances. There are only two people living in this house so there is only minimal usage. To further complicate things, there is no serial number on the tag.

2 year old GE ADORA dishwasher - I am so disturbed tonight after seeing what happened to the protection rubber that is on the exterior of my dishwasher. I decided to buy a new dishwasher because the bottom tray would not stop when pulled out at the correct stopping point. Today I got my new dishwasher installed and when the installers pulled the old one out I was shocked to see that the protectant that I would assume was placed to protect my house was melted all over my wall behind the dishwasher. WOW. Talk about a MAJOR fire hazard. Thank God my house didnt catch on fire because of this faulty equipment. Check out my pictures and you will see the pile of protectant that was under, on my wall, and behind the dishwasher once it was pulled out. Sincerely concerned.

I may be speaking too soon because I need to run my dishwasher again to make sure the minor leak truly has been fixed, but I am very impressed with the responsiveness of GE customer support. There was virtually no wait to talk to a rep about my 2-month-old dishwasher with a drip (plus water was collecting inside). Less than twenty four hours after my call, a friendly man was at my door to fully diagnose and then correct the issue. This was the cheapest, bottom-of-the line model that they so quickly came to service! Now in an ideal world, a new dishwasher wouldnt need any servicing at all, but I think all dishwashers are pretty finicky so at the moment, Im pleased.

Purchased new from Lowes. Dishwasher leaked starting less than a month after purchase. I have had it serviced 3 times since purchase and have another appointment scheduled. (It takes 2-4 weeks to get a tech out to your house). Currently they say he is going to come by on Tues and check to see which part to order next and then they will come back and work on the dishwasher when the part comes in. (Of course the dishwasher is leaking as I wait). They give a 8-5 service window so I will just have to sit here and wait on him to come by and decide what to order. This is pathetic. When you buy a new GE appliance you need to be aware that they literally do not have any program for replacing flawed appliances.

We have had our GE Advantium for 4+ years and the paint has started to peel off the inside of the door. We have an extended warranty with Home Depot but they deem this a cosmetic issue which is not covered. The cost to replace the door (part only) is about $260. Not sure self-painting is safe. I read here that we are not alone in GE microwave paint peeling off inside their microwaves, in general. Has there been any recall or calls action against them for this shoddy product? We love having this microwave/oven but feel like we got hosed by GE and Home Depot.

GE over the range microwave Model hvm1750DM1 WW - It’s just about 2 years old. It started making a grinding noise, then quit. No more GE for me.

I purchased a GE Spacemaker Microwave model JVM 1750SP1SS from Best Buy in October of 2011. Just a few months after having the microwave, the handle came off. I called GE and they sent a technician and fixed it but it left scratches on the stainless steel. In addition, we have had problems with the turntable. Finally on March of 2013, the keypad went out. This of course is past the one-year warranty. I called GE and they told me that they could schedule a service call for $89.95 plus parts and labor. I told them that I could buy another microwave from another company for less than that would probably cost. This microwave was made in Malaysia. I would not recommend any GE appliances that are not made in the US.

I purchased this dishwasher (GE Dishwasher Model # PDWT180RSS) at the beginning of March and it has been nothing but a disappointment and inconvenience. Nothing gets clean. It has been serviced 5 times and I have a case # with GE. They have serviced the jets, used 3 different kinds of dish soap, checked the water pressure, temperature, and drain and still it does not work right! What a hunk of junk. Dont buy GE products.

I wasted my whole day waiting for GE Technician to come. Nobody called me to let me know that they are not coming. I have to call them only for a Mr. ** to tell me that they had rescheduled the appointment for another one week without notifying me. Good job that GE APPLIANCES are doing. You remember the so called TOO BIG TO FAIL? It means, they can do whatever they want at whatever time or day they want. I dont have a vent in my house and that means I cant use the stove. Is this ridiculous or I am missing something here? Is it TOO BIG TO FAIL? Yes, I forgot that. I will be staying in a house with a new GE APPLIANCE that has not been working for the last one week and have to wait for another week. Mind you, this Appliance has been used only for barely a month. Is there anybody out there who is facing the same problem or its just me. If there is nobody going through the same experience, an excuse like there are no Technicians available to come to your place and do the job. If there is anybody out there who has trust in GE appliances like I did or even thinking of getting one. Be aware that you will be through what I am going through and there will be no technician available for another two weeks. Be ready to wait for they will reschedule your appointment without letting you know, why? Because theyre TOO BIG TO FAIL. What will you do? Wait until they decide to come, if theres a technician available. I just realized that GE means GO ELSEWHERE. Thanks GE for the good job.

I pushed the oven cleaning button. After about 2 hrs I noticed smoke coming from the stove and the island where it is installed. The door would not open and the oven just got hotter and hotter and smoke was filling my house. I called 911 and they sent the fire department. After disarming the breaker, they removed the stove. I purchased the stove in 1996 but only used the auto oven cleaner a few times. The model # is jsp40 and serial # TR244121R. If I had not been home my house would have burned. GE you should do something about this situation. I have no receipt or order #. I purchased it too long ago.

Ive had an overall good experience with the dishwasher although sometimes I feel that you have to do too much prewashing and the dish wash cycle takes a really long time.

Have used GE dishwashers before - were good. However GE no longer makes them, its just a name - now made by MABE (part of HAIER), Mexican with Chinese ownership, and this new one arrived with a factory fault - cracked tub which leaked immediately. Cracked tub seam and leak found immediately by service tech GEs site referred. Good news is the leak detector worked! Bad news - is we didnt install it right away (old one still worked and pandemic...) so it was a year before we got to it (was partly a gift). So - now MFR Mabe is giving us the run around and so far not doing anything about the faulty dishwasher they mfd and shipped through Home Depot. Dont be fooled as we were - GE is not actually GE anymore and the mfr HAIER/MABE are doing nothing to correct a factory mfg fault.

Bought a PDT845SSJ2SS in June. Two months later, it has a leak. Good news, has a leak detector which shuts down the machine. Bad news is that it leaks and the leak detector worked! Called GE. We dont have an authorized service technician in your area. We will get back to you within 3-5 days. Three days later, after I had raised rain with my appliance dealer, he arranged for a local dealer to come look at the machine. Scheduled that appointment - it was Friday, and We only come to your area on Tuesdays and Thursdays. Next Tuesday is booked, so we will try for Friday. Then, someone from an organization called Platinum Services calls and says GE has assigned the ticket to them. Shes going to try to schedule a diagnostic appointment in the next 7-10 BUSINESS days. Told her to forget it (found out she was calling from Lowes and had to find a technician before she could schedule.) End of week 1. Following week, someone else from GE calls and asks if I was cancelling my service request. In the course of the conversation, she asks to confirm the model GE RANGE that I have. Kinda lost it on her... On Thursday serviceman from local dealer comes. Turns on the dishwasher - it leaks exactly where I had said it would. Need to order a part and GE will not expedite. End of week 2. Next week - crickets. Nothing, Nada, mushroom mode (in the dark and being fed BS). Called my appliance dealer today and told him to come pick up the dishwasher - says he cannot do that. I explained, “I will forfeit the money I paid - I dont want a dishwasher that leaks in the first two months of use.” He tell me GE released the part yesterday...whatever THAT means and he HOPES repairman will come next Tuesday to repair. So, I have had a new GE dishwasher for 3 months and it has only worked for 2. Be aware! I assume partial responsibility for this goat rope - I faithfully refer to Consumer Reports when purchasing appliances and electronics. I suggest you do the same... you will find GE listed AFTER BOSCH, KITCHENAID, KENMORE and others. Also, realize the GE brand is now a CHINESE company. Caveat Emptor!

From these posts, Ive seen people saying that they couldnt trust GE American-made anymore. Our microwave oven was made in Malaysia, but GEs home office appears to be in Louisville, Kentucky. Our problem: peeling paint on the door and upper part of our 2009 GE #JES1451DN1WW oven. As a cancer survivor of 8 years, my antenna goes up with any defaults such as this. On a common sense scale this should never be happening. I was very sad to see no recalls on these items Ive been reading about and am frankly scared to use this microwave. Shame on you, GE.

I purchased a microwave in Oct 2010. It went blank and nothing works. I checked to see if its receiving power. The power is okay. I purchased the microwave, fridge and stove at the same time. I always had confidence in GE products. Microwave should have lasted longer than less than 2 years. I didnt purchase extended warranty because of GEs reputation. Very dissatisfied customer.

This is a review from another customer “Not only does this dishwasher do a lousy job of cleaning dishes, I have just found out it allows dirt to collect under the door flange==lots of dirt! There isnt enough hot water to clean this out. Very gross--do not buy.” I agree with this 100%. I have to use Clorox wipes to wipe out this disgusting sludge that builds up under the door flange every couple days. I have to buy a new dishwasher because my dishes smell, are still dirty and very unsanitary. Do not buy!!!! My dishwasher is only 3 years old.

18 Dishwasher Model GSM1860VSS - Cleans terrifically but I have a problem with either a leak or steam which is running the front of my dishwasher and marking it. It seems to be leaking from the black panel across the top. If I check inside behind the black panel I can see marks where water has been running. Please let me know how to fix this. The dishwasher was bought in 2015 and have the receipt from Home Depot. Thanks.

I bought a GE Profile dishwasher 3 years ago. After two weeks it was broken. I called Mabe Appliances and they sent out a tech. He told me it was broken. When I called Mabe back the service people told me to read the manual...yes really. Finally after a lot arguing they replaced it. About a day after the 1 year warranty expired all but one of the cycles stopped working. I have to take it apart every 3 months to clean out the water output as its clogged and the water doesnt have any pressure and therefore does not clean the dishes. I got up this morning and the dishwasher was still running but there were no lights on the front of the unit. I turned it on around 8pm so it was running for 11 hours. When I opened the door it was apparent it had been stuck in the wash cycle the whole time. It is now completely dead. Nothing works. No lights. WHAT a piece of JUNK. How can GE put their name this crap? STAY AWAY FROM GE APPLIANCES. Spend a little more and get a Samsung or LG or Bosch.

Model WES1130 GE Microwave - The entire interior of the microwave just started peeling off the coating/finish around 3 years after purchase. The turntable wheel guide path totally disintegrated the finish of the path. It still worked but was so unsightly and disgusting to look into the interior and possibly dangerous to eat anything that had been put inside to cook. I just got rid of it. I purchased another GE Model JES1460DSBB and it started malfunctioning after 3 weeks. I returned it and will not buy another GE product.

No issues yet. But only had for 6 months so time will tell. Read a lot of negative reviews but none here. Bought in Nov ‘18 from Home Depot. Delivered and installed on time. Replaced 13 yr old GE appliances that were still working.

We have a 2017 GE profile built on microwave. The microwave started shooting fire inside the microwave a year ago. GE fixed it. Last week the microwave started shootings fire inside the microwave again. This time it was much worse. The GE technician told me it was not fixable. I called GE customer relations and was told too bad because it’s not under warranty anymore. They offered a minimal discount on a new similar model. The attitudes of the customer care representative and supervisor took me by surprise. They were curt and told me, Guess you should have gotten the extended warranty. When it comes time to replace my kitchen there will not be any GE products in it. GE does not stand behind their products. The tech told me there are issues with the profile microwave and he felt they would replace it. They did not replace it and were rude. I have been a loyal GE customer. Not anymore.

We purchased a VERY expensive GE dishwasher (Re: Case: 13259178, Model: PDWT580V00SS, Serial No:MZ841691B) for over $1500 and IT DOES NOT WORK! It actually DESTROYS dishes! It leaves a thick detergent film on plastic cups and plates and renders them unusable. We have scheduled no less than FIVE technician visits and all of them refuse to indicate that the dishwasher is faulty and needs to be replaced or they would likely lose their job. All they say in their report is that the dishwasher is performing normally. So a dishwasher that DESTROYS dishes is NORMAL? GE is a $265 billion company. They have a customer that is infuriated with a faulty product that they will not replace. They are giving us the runaround and it is unconscionable. Any other consumer focused business would have replaced their product by now. Not GE. They have a huge infrastructure built to keep consumers from getting their products repaired or replaced correctly. This feels like Davey Vs. Goliath but we are going to prevail. My advice to all consumer is to NOT EVER buy a GE dishwasher, unless they like to have their dishes ruined.

I bought a GE dishwasher model #GDF570SSJSS from Sears. It was delivered on Thursday, installed Friday (by myself and a daughter) and the first test run produced nasty, dirty dishes. It took 2 hours and 10 minutes for it to declare that the cycle was finished and the dishes were clean. Fortunately I did not opt for the drying cycle. Or else the nasty crud would have been baked on. I called GE service and they scheduled a Monday service call. Monday, a very nice man hooked the unit up to his computer and found nothing wrong. He then placed a plexiglass door on the unit so he could watch the cycle. He found that the connection to the upper arm was not attached. He snapped it into place and declared that it was fixed.While I watched through the plexiglass door I was appalled that the reason that the GE dishwashers are so quiet is that the washing spray is extremely gentle. The technician seemed very proud of how quiet the units are. I told him that I could get my dishes cleaner if I spread them on the lawn and used a water hose sprayer. He was not amused. I chatted with him and asked several questions and learned some interesting facts. The lower and upper spray arms and the top rain action do not all happen at once. First the lower arm sprays, the machine pauses, then the upper arm sprays, the machine pauses, then the top rain action happens. This cycles over and over until the machine thinks the dishes are clean. I asked why there wasnt a hurricane inside the unit scrubbing my dishes? He said that the motor is a DC motor, I asked how many volts, he said 12.After he left I filled the machine up with dishes I had saved over the weekend for the test. The machine ran for 2 hours + (I forgot to write down the start time). The end result was nasty, dirty dishes that I washed in the sink afterward. So the new dishwasher looks just like the old dishwasher but let me tell you, she is not happy at having the worthless piece of junk sitting nearby and doing nothing while she is sweating over a sink full of dishes. When Im not quite so angry in a few days I will have a conversation with Sears to try to resolve this.

This dryer replaced an eight year old Frigidaire Gallery Series. The new GE dryer is drying clothes much quicker. I have read some reviews complaining of the buzzer, but it is a nice feature to know when the cycle is about to complete. The nice thing about this dryer is that it has the right amount of dial drying features needed without a bunch of electronics that can typically cost a big service call if gone bad. Also the bottom rear of the dryer allowed enough room for the exhaust to go either left or right behind the dryer with it still sitting close to the back wall. I was lucky to find this as an open box item returned to the store because it was not a gas dryer for the first buyer. Photo shows exhaust located to outside wall.