I purchased a GDF520PGJ dishwasher from Home Depot and it still doesnt work. Home Depot has no return policy and G.E. has been unable to resolve. I have written to GE Appliances Consumer Relations for a replacement but pending another service call. Its unfortunate that there is no recourse with Home Depot as was advised that I need to work with GE for the first year warranty yet my dishwasher hasnt worked for the past month. Buyer beware.

Three nights ago, I loaded my GE Profile Dishwasher, model # PDW9880L00SS and began the wash cycle. The wash cycle completed and I went off to bed leaving it on the dry cycle. The next morning I smelled a burning smell but did not know where it was coming from in my home. A few hours later, my husband began searching all of the appliances in our home to see what the burning smell was. When he opened the dishwasher smoke came out of it and everything in it was completely burned. Apparently the drying mechanism never turned off after the wash cycle or it turned itself back on only on the dry cycle. I dont know. But I know one thing for sure, we are lucky that my husband was home because I left and if he wasnt there, Im positive that the dishwasher would have caught on fire causing severe damage to our home. I will never purchase a GE appliance again. Note, I also have problems with my GE refrigerator and my GE Profile microwave and our dryer. Weve had to replace the dryer and the microwave and weve repaired the refrigerator. I have a repair person coming out to see if the dishwasher is repairable, but I dont think it will be. This is terrible.

We wrote to GE regarding the issue with the dishwasher and, after some phone tag, a certified GE engineer came to the house, diagnosed the problem and ordered all the replacement parts. This morning, they came by to install and essentially rebuild the entire system with the exception of the stainless steel. Overall, we are very happy with the outcome. With all the negative issues GE experiences online with regard to the Cafe Series, I give them a solid 8 for responsiveness and taking care of the situation. Perhaps ours is a rarity, but if you approach them logically and with facts, they seem willing to work with the consumer. Heres hoping the system cleans better now too!

Had it over 12 yrs. Never a problem. It’s a wall mount microwave. Easy to clean stainless steel. A bit of a pain to clean the stainless steel inside of microwave. Would recommend the microwave to people looking for one.

I bought a GE dishwasher model #GDF570SSJSS from Sears. It was delivered on Thursday, installed Friday (by myself and a daughter) and the first test run produced nasty, dirty dishes. It took 2 hours and 10 minutes for it to declare that the cycle was finished and the dishes were clean. Fortunately I did not opt for the drying cycle. Or else the nasty crud would have been baked on. I called GE service and they scheduled a Monday service call. Monday, a very nice man hooked the unit up to his computer and found nothing wrong. He then placed a plexiglass door on the unit so he could watch the cycle. He found that the connection to the upper arm was not attached. He snapped it into place and declared that it was fixed.While I watched through the plexiglass door I was appalled that the reason that the GE dishwashers are so quiet is that the washing spray is extremely gentle. The technician seemed very proud of how quiet the units are. I told him that I could get my dishes cleaner if I spread them on the lawn and used a water hose sprayer. He was not amused. I chatted with him and asked several questions and learned some interesting facts. The lower and upper spray arms and the top rain action do not all happen at once. First the lower arm sprays, the machine pauses, then the upper arm sprays, the machine pauses, then the top rain action happens. This cycles over and over until the machine thinks the dishes are clean. I asked why there wasnt a hurricane inside the unit scrubbing my dishes? He said that the motor is a DC motor, I asked how many volts, he said 12.After he left I filled the machine up with dishes I had saved over the weekend for the test. The machine ran for 2 hours + (I forgot to write down the start time). The end result was nasty, dirty dishes that I washed in the sink afterward. So the new dishwasher looks just like the old dishwasher but let me tell you, she is not happy at having the worthless piece of junk sitting nearby and doing nothing while she is sweating over a sink full of dishes. When Im not quite so angry in a few days I will have a conversation with Sears to try to resolve this.

This dishwasher model no. GDL6860N00SS and serial no. DM833394B was purchased in the summer of 2008 and has given me no problems until now. I used it last around 3pm on October 11, 2011 and apparently it was still heating up because my husband noticed a plastic burning smell the next morning. So he opened the dishwasher and it was burning hot! It had my granite countertop scorching hot, it also started to melt the bottle on the top of the counter. I think this could be a manufacturers defect.

Our microwave, model number JVM1750DP1BB, was manufactured May 2011. On Monday, Dec. 30, I was heating a bagel when the small plastic hook holding the rack caught fire. The interior of the microwave burned, but I was able to put it out before it spread too far. I shudder to think what might have happened it I had been in another room. Im irritated because I keep reading that this is a common problem. Im irritated because MY HOUSE COULD HAVE BURNED DOWN. Im irritated because it seems like GE isnt doing a great job at making it right. Ive attached a photo below, showing where the plastic pin burned. I can say that Im shopping for a new over-the-range micro, and it wont come from GE.

Second GE Spacesaver Microwave - It is a total mystery, no clock, no light, no fan, no power. We replaced a GE Spacesaver that came with our house with a new GE Spacesaver Adora (Model DVM1850DM4WW). It has been in use for less than 2 years and has been used only a few times per week. I have a Sharp Carousel II that we use in our basement. It gets as much use as the new GE. It is 28 years old, and works fine every day. This is the second GE product and this one lasted less than 2 years. Ill never buy another GE product. I was trying to support an American company. Anyone know a good one that makes microwaves?

I give it stars for value because an extra step is needed to set cooking time. Most microwaves do not require pressing a cook time key before selecting # of seconds. Other than that, microwave is first-rate and very dependable. We use it several times a day for 1.5 years now with no problems.

Updated on 12/30/2018: Again had GE up, said it was not the pump as they stated. Hired a plumber as they requested, pipe not blocked. Changed connections and now the machine has no power. Again have to call for repair. I am sure they will have to order a part or tell me to call an electrician. I am so done. Please beware. Do not buy. Still not been able to use my dishwasher going on 4 weeks and brand new.Original Review: Purchased from Home Depot. I have had it for only one month used 4 times. The water did not drain. Called GE Repair. Guy came down, couldn’t figure out what was going on, said it must be the pump or it could be blocked. He went downstairs, could not find the pipe. Been there since 69...said he is going to order part. Waited 1 week. Then he calls me an hour before he was to be here. Mind you I took off work to be there. He said, “Did you have plumber to come in to see if there is a blockage and he needs to show you where the connection is?” Are you kidding me. I told him I am handicapped and having company for Christmas and I need it. He said he can’t come until I hire a plumber as he can’t find the dishwasher connections. Are you kidding?I said, “Can you come and install the pump and if it doesn’t drain then I will call the plumber.” He said no as he can’t find the connection...I am going to put 150 to have a plumber come when I know it’s the pump not a blockage to have the plumber show me where the dishwasher is connected because the idiot can’t figure it out. I said I need it for Christmas. Nobody working until next Wednesday. Do not get a GE. Poor customer service and to break down a few weeks after purchasing is unacceptable. I had A Bosch for 6 years, never a problem. Plus the lower rack tracks already fell apart. I live by myself and does not get much use. I read the reviews and should have known. The only reason I purchased I needed the bisque color. BUYER BEWARE.

We have a 2017 GE profile built on microwave. The microwave started shooting fire inside the microwave a year ago. GE fixed it. Last week the microwave started shootings fire inside the microwave again. This time it was much worse. The GE technician told me it was not fixable. I called GE customer relations and was told too bad because it’s not under warranty anymore. They offered a minimal discount on a new similar model. The attitudes of the customer care representative and supervisor took me by surprise. They were curt and told me, Guess you should have gotten the extended warranty. When it comes time to replace my kitchen there will not be any GE products in it. GE does not stand behind their products. The tech told me there are issues with the profile microwave and he felt they would replace it. They did not replace it and were rude. I have been a loyal GE customer. Not anymore.

Our microwave was manufactured in September 2010 and we purchased it in October 2010. It has been used a few times a week for reheating leftovers. I have owned secondhand microwaves and unknown brand microwaves, and they have been more reliable than the GE Profile. My husband and I invested in the Profile series when we remodeled our kitchen. After a lifetime of moving and living in homes with much to be desired kitchens, we decided to spend money to provide ourselves with a functional kitchen. If I had to do it all over again, I would have saved myself the trouble and purchased my appliances from another company.After having to call GE to send out a repair person 5 different times to work in our microwave oven, we are left with a nonworking microwave oven. It seems that a company that has made record profits from their faithful American fans could do the right thing and replace the microwave oven with something that works. Perhaps they do not have such a product. They have offered to let us buy a new one at a big discount, but they have not clarified what the percentage will be. The problem I have with this is that spending one more dollar on a product with no backing from the company it came from would be asking for more let down. I believe Ill have this lemon removed and quit before I take on any more consumer letdowns.

My dishwasher is a little over 3 months old. Sure its quiet. But I use the heat dry always, but it doesnt dry the top bottom or side walls and it stinks and a lot of food is sitting on the strainer and stinks. I have owned a GE dishwasher for over 25 Years and have never had one that was not completely dry at end of cycle. I have to hand dry my silverware. My Model Number is GDF510PSD4SS Serial number is FF736760B. I want a full refund and take back this reject. I will buy something else, I assure you it will not be a GE Product. Sign me, thoroughly disgusted with this Ge product.

We had purchased the first listed model of dishwasher (Model PTD7505SSF8SS) and installed it on Aug 27/16. It worked for a total of 13 days and broke down on Sept 9/16. After a good deal of phone tag - a technician looked at it and said no less than 3 internal components had failed, the unit needed to be replaced. We were without the unit from Sept 9/16 until Dec 23/17 when the new replacement unit (Model PTD845SSJOSS) was installed. It worked for a total of 20 days and broke down on Jan 12/17. More phone tag... Tech looked at it and found a number of issues (motherboard, door switch, etc...), in addition - it had been leaking water under the dishwasher for the time it was in service. (All 20 days! What a record!)When a dishwasher leaks upstairs... It doesnt go well for the drywall ceiling downstairs. (The rep at GE was cold and calculated informing me that is what insurance is for!) Im not sure that is what someone who spent $1,699.00 for a GE product (in good faith of a reputable product) expects to be told by the individual who has the ability to make things right? At any rate, this is what you can expect from the trained professionals at GE. When they finally got around to looking at my file... They decided to simply replace the motherboard in the hopes it will fix the leak also.I would have liked a refund at this point (not likely) so I requested yet another replacement (given the issue of water leaking), they absolutely refused. As of this date Feb 2/17 we are still without a dishwasher. Goes without saying - no more GE products will enter our home and I will share, with everyone I can, the caring and kind words of support I experienced from the top level at GE.

I purchased a GE Profile dishwasher in June 2015. It was delivered dented.19 July it was replaced. The dishwasher worked for 3 months. Then it stopped working and the display panel had a LEAK DETECTED, DO NOT USE, notification. We contacted GE who could not find a GE repair technician to come and repair it in the entire BAY AREA. The dishwasher was bought at SEARS who refuses to take any responsibility.

Not very satisfied with the functionality. Turntable does not work or has ever worked. Time features and power adjustments are not very intuitive. I would not recommend this brand, I believe there are other brands out there are much better for the same price range.

Cleans ok but not sure if its detergent or dishwasher but never seems to get all dishes completely clean. It may leave a ring in my tea cup so sometimes Ill have to clean it slightly to make sure it comes off. Basic settings on mine, nothing special. Good for plates and some Pyrex cookware but it would be nice if I could put larger pots in it. Very basic white in color but it is over 10 years old.

Great microwave I have had for almost 10 years. It works like new. Its a name you can trust and not expensive at all. I have always believed in the GE name and their products. I have a dishwasher and dryer that work just as well. I will continue to buy GE products.

The GE dishwasher was in place in the home that we bought in 2017. I like the stainless steel outer color, the noise level is minimal, which I like. The options for different cleaning levels are great. It does a good job at cleaning our dishes. My only negative comment is that it was new when the house was built in 2017. For the past three months it has been stopping repeatedly, multiple times, mid-cycle so that you have to repulse the start button multiple times to finish the cycle. It is barely three years old and seems to already be giving out which means we will have to replace it, probably soon.

18 Dishwasher Model GSM1860VSS - Cleans terrifically but I have a problem with either a leak or steam which is running the front of my dishwasher and marking it. It seems to be leaking from the black panel across the top. If I check inside behind the black panel I can see marks where water has been running. Please let me know how to fix this. The dishwasher was bought in 2015 and have the receipt from Home Depot. Thanks.

I purchased this dishwasher 2 months ago and am VERY disappointed with its performance. For an appliance that claims energy efficiency it is a total failure. My last dishwasher was a Kenmore that I had for 15 years. It outperformed this thing in every aspect. Since purchasing this dishwasher my water bill has gone up and my energy consumption has gone up. Why? Because I cannot put plates close together in this energy hog or they will not get clean. I have to do twice as many washings as I used to for the same results. This piece of junk has NO WASH PRESSURE! All the dishes must be pre-washed in the sink to assure satisfactory results AND I must use the hot water boost or they will not get clean. Energy wasted doing a pre-clean and energy wasted with hot water boost - bad combination! This product is taking me backwards in savings and environmental damage.

Ive used this GE model JES2051DN1BB (manufacturer date August 2008) microwave for ten years now and impressed that it is still working perfectly cause you dont see that much anymore. I usually prefer Maytag products cause my GE washer and dryer did not last for me, but this has seem to be different. Maybe GE should stick to making microwave ovens instead of anything else.

Our GE microwave stopped working after about 7 months of use. Ive never had a microwave break down on me before. Ive owned other brands which Ive used for years, actually lasted over 10 years. The only reason we purchased the GE microwave was because our old microwave was too big in size. I called GE for warranty service and it was very much of a hassle just to make the appointment. I had to call several times because a customer service representative misinformed me. It took a couple days just to set up a service appointment.Ive told the representative that the microwave stopped working and will not power back on again. The representative told me that the fuse probably went out. Something must have blown out. Finally, the appointment was made for about a week later, which was the earliest time available. It is so inconvenient not to have a working microwave even just for a day. Anyhow, the service tech came about two hours late. The scheduled time was for 8am-12 pm. He showed up close to 2pm. A family member was waiting at home all day because of this. Then the service tech told us that he needs to order a part for the microwave and that he will return a week later to repair the microwave.A week later, he didnt show up. No one even called. So I called back GE and found out that the appointment has been postponed! So now, we have been without a microwave for about three weeks. I think this is ridiculous. Im pretty sure that this is a common problem with GE microwaves and they already had an idea why the microwave wasnt working. It doesnt power-up! Now they are telling me that they dont have the part/s in stock? If I had known that we had to invest so much time and go through so much hassle from the get-go, I would have just purchased a new microwave three weeks ago. GE should pay me for all the time Ive wasted!

Our over the range microwave oven is under warranty and broke twice. They refuse to replace it. It was fixed the first time but its broke again and the only service tech refuses to come to our home to service it anymore. Its been a nightmare and still not resolved. We will never purchase another GE Appliance ever again!

Called out GE service tech to diagnose my dishwasher which was not draining after the wash cycle ended. Was told it was the control board and it would be best to buy a new dishwasher. Purchased a control board online (was a GE original part for a lot less than the GE price) but it did not solve the problem. After researching the problem online, I found out that it could be the drain valve. Sure enough, bought one for $14, installed it myself and the dishwasher works like new. Called GE Service to try and get a refund for the service visit ($89), was told that I had 30 days to have the tech come back out at no charge. Tech never advised me of this policy and GE will not refund my money.

After heating some water in the microwave, I opened the door and removed the water. A few minutes later, I heard a noise and noticed the microwave was running and the control panel indicated it was off. I opened the door it turned off. Closed it and it was on. Smelled something burning electrical in nature. I had to kill the circuit breaker to turn it off. I opened the door and felt the inside of the microwave and it was extremely hot. I was concerned that it could result in a potential fire, I continually checked it until I felt it was cool.

Very convenient. Easy to use. Take some time to clean though, have to cover all food for splatter of food on the topside inside of microwave, have scour off with strong pad. Also it is not radiation free for health. But the microwave is easy to lift. The best thing about it you can cook frozen foods. Like meatloaf, beef stew my favorite, pizza, chicken.

I moved into a house with the dishwasher already installed and it didnt work. We closed it so we didnt use electricity but it started and wouldnt stop. The power button is broken. It just sits there and the lights are always lit. I tried calling for help but the workers were very unhelpful. I called a different number and was waiting a whole five minutes and no one picked up!

We have had our GE Advantium for 4+ years and the paint has started to peel off the inside of the door. We have an extended warranty with Home Depot but they deem this a cosmetic issue which is not covered. The cost to replace the door (part only) is about $260. Not sure self-painting is safe. I read here that we are not alone in GE microwave paint peeling off inside their microwaves, in general. Has there been any recall or calls action against them for this shoddy product? We love having this microwave/oven but feel like we got hosed by GE and Home Depot.

Very quiet and cleans a large volume of dishes. Love the silverware rack and the overall look of the dishwasher. Also great value for the money. Though we have only had for three years it has held up great.

My dishwasher is very quiet and effective in its use. I am very pleased with my unit as I saves water and power when in use. It also cleans very well and smells good as it drains completely. General Electric is very reliable and outstanding company and is made in the USA.

I purchased this dishwasher (GE Dishwasher Model # PDWT180RSS) at the beginning of March and it has been nothing but a disappointment and inconvenience. Nothing gets clean. It has been serviced 5 times and I have a case # with GE. They have serviced the jets, used 3 different kinds of dish soap, checked the water pressure, temperature, and drain and still it does not work right! What a hunk of junk. Dont buy GE products.

I do not remember what I paid for this microwave, but my budget was low, and the value I got is good for the money. Ive never had any trouble with this oven, and its 5 years old. Its a good size and cooks evenly.

I live in a condominium building with approximately 105 units. We all had the same GE microwave installed in our units approximately five years ago (contractor-installed). I sent out a mass email to all of the owners to ask if they were having the same problems I was having my microwave, which was the touch panel will not accept commands. I received approximately 15 complaints from various homeowners with the same complaint.When I called GE to tell them the problem I was having with my microwave, they told me a technician would have to come out and diagnose the problem. The service call would be $99.95, and at that time the technician would let me know what the problem was and tell me the charge for the replacement part and labor cost. I told GE Customer Service that there were many people in my condo building who were having the same problem and I wanted to know why each homeowner should have to pay the initial $99.95 service call fee? The response was, That is our policy. To placate me, GE customer service said they would charge me the initial fee but I would receive a 25% discount for parts and labor.In the meantime, two or three other homeowners made service call appointments for their microwave oven with GE. One homeowner was given a fee for parts and labor, which would have been only slightly less than buying a new microwave and another homeowner was not given a labor cost. In both cases, the homeowners did not go forth with their repairs, because buying a new microwave was more cost effective.I want Consumer Affairs to know GE grossly mishandled this malfunction issue amongst a group of homeowners who own the same microwave. Secondly, I realize the microwave ovens are five years old, but GE should have some record regarding failing parts along with the life cycle of this product. Lastly, I want GE to be held accountable for not telling consumers a repair cost for certain issues. There should be a cost per hour, not cost per broken item.I kept records of all correspondence amongst the homeowners of my condominium building, so I will be of great assistance if you need further help from me. Product malfunction is a GE Profile Spacemaker 2.0 Model # JVM2070SK02.

Fourteen months after buying my new built-in GE Profile Microwave/Convection, it stopped heating. I was told by GE that it was not under warranty. I paid close to $300 to an appliance service operation locally to fix my nearly $1,000.00 GE built-in (depending on the microwave to help feed four kids under the age of nine). So, about 13 months later I had another heating issue and I called the appliance service operation and they found another problem with the microwave. They said it was a faulty piece of equipment, replaced it and didnt charge me since they were local and said this shouldnt have happened (knew I was recently divorced and took pity on me). Almost 18 months after this, so three years after the purchase, the microwave started to act up again - it continues to work even after you open the microwave. Just dealt with it since it still worked. However, 6 months later, the microwave now doesnt heat. The power is on, and nothing happens inside. This started a week ago, but it was off and on. Now its dead. Never buying a GE anything. Ive got to buy a microwave and a refrigerator in the next six months. It is NOT going to be a GE!

We bought 3 GE Profile appliances in 2005 when we renovated our kitchen. We have not had much problem with the gas oven/range/stove. We have, however, had nothing but problems with the microwave (which I submitted a separate review for) and the dishwasher. Recently, a friend made some suggestions regarding the dishwasher. I then went online and watched some tutorials on troubleshooting my dishwasher problems. I tried all the new suggestions and the dishwasher worked OK the one or two times after that and then back to all the old problems: 1. We have to scour every dish until its nearly clean before loading (even though the instructions specifically stated no pre-rinsing necessary). 2. I am not sure the soap cup opens. The soap is always left caked in the cup resulting in running the dishwasher twice. We have tried all kinds of various soaps and they all do the same thing. The eco-friendly soaps are the worst. We strive to be eco-friendly, but how can we be if we are using the harshest soaps possible AND running our dishwasher twice?! Not to mention the pre-rinse scour and running water until it is 120 degrees prior to running.3. The dishwasher also leaks and is very noisy.I have read some other reviews on this product and realize our dishes are not always dry at the end. This is a non-issue for me. I dont care so much if the dishes are dry. I do prefer for them to be clean. Dishes are a task I do not prefer to do. It would be nice to have a functioning helper. I am grateful the thing hasnt caught on fire. I saw that this dishwasher currently sells for $800-$1,500. I cannot believe it. I wouldnt spend $100 on this piece of junk.

Have a six-year-old GE Tall Tub Café dishwasher (model#GHDT168V00SS) I purchased at Home Depot in Denver. Also purchased a 5 Year Extended Warranty that I assumed was through GEs Extended Warranty Opportunity. The dishwasher suddenly began leaking and ruined our hardwood floors (I know, wood floors in kitchen not good; tell that to the builder). I called GEs customer care number and basically talked to a scripted robot. You dont have a warranty through GE, its a third-part insurer such as Assurant, I was told. Not worth repairing, and the warranty expired a few months ago. I know parts wear out, but for heavens sake, cant they build a dishwasher that doesnt leak from the bottom, underneath the unit, where water will seep unbeknownst to people, eventually destroying the floor? Guess not. So, no more GE appliances EVER. PERIOD! Switched to Samsung, LG and Maytag. Now, gotta spend a couple grand ($2K+) to repair the hardwood floor.

We bought a GE dishwasher model GDT720SGFWW thinking that GE was a reliable brand... What a disappointment! The first dishwasher we received was damaged and the door would not close properly. It took a week for GE to send a repair technician who confirmed that the unit was defective beyond repair. It took another week for GE to order a replacement unit and another week to get it delivered. The replacement unit arrived today and guess what? It is also damaged and the door will not close, same problem as the first one! Terrible products, slow service. I will never buy a GE appliance again!

I have just purchased a new GE dishwasher because mine just broke after 35 long years of excellent service. I am so completely satisfied with your GE products, and I would like to tell you also that the double oven stoves are still working well.

We had a new GE Monogram dishwasher installed September 2014, a little over a year. We had a hose leak and it cost us $229.00. I do not recommend this product.

Microwave oven 2008 - The food doesnt go around anymore. The glass insert does not turn. What can I do?

Purchased new home and bought GE Monogram package. Within 6 months dishwasher started leaking bottom of door. After five repair service calls. (Thats 10 times waiting for service man or for parts to be stalled). The final repair killed the dishwasher dead and GE replaced it with a new Monogram dishwasher. I thought all was working fine but then this new dishwasher developed a leak underneath and the sensor shut it down completely. Service call made to GE and a GE service man came, only he couldnt get to the leak area because he couldnt pull the dishwasher out because the connecting water hose was being stretched so tight he said he couldnt disconnect it because he couldnt see behind the unit or the drawers to see where it was hung up. Plus he is not authorized to install or reinstall dishwashers. So I call GE repair and now have spoken to the most uncaring, dis concerned case manager handling my account. He tells me that this now a installation problem and that even though GE delivered the dishwasher and installed it that because these were outside venders they (GE) were not responsible for the installation and dont know if they used GE standards to install it. So because the GE service man couldnt move the dishwasher I now needed to get a plumber to disconnect the dishwasher, find out what the problem is with the installation, coordinate a service call date with GE service to then come out and put in the parts, then have a plumber back in to install the dishwasher again. GE will reimburse me up to $125 for the plumbers work and I have to submit the plumbers invoice. No guarantee that a leak will happen again, because the GE service man cant even run a test on the replacement parts because the dishwasher isnt hooked up to water and he cant do that because he isnt authorized by GE to install. Oh, the dishwashers warranty ended on 10/10/2015. My service call went in three days before it was to expire so service is covered for the leak (or so I have been told). But what will breakdown next with this appliance? I bought GEs top of the line package. I bought a MADE IN USA appliance and I can honestly say that this GE appliance turned out to be unreliable, unrepairable and their case managers uncaring. I will never ever, ever buy another GE appliance. I will never recommend any GE appliances to anyone ever. My KitchenAid lasted for 26 years without a service call. When I remodeled my kitchen I purchased a Bosch dishwasher. That pleasure was 13 years old when we sold our home. We have been in this new home for 1-1/2 years and now on my second dishwasher with a future of many service calls ahead and very bad taste for GE. If this leak problem is not fixed or another problem arises, I will yank this dishwasher out and buy another brand. A reliable one and definitely not a General Electric EVER! Since this GE Monogram package was purchased at P.C. Richards they will also be notified of my displeasure and I will continue my discourse of GE forever for their lack of product truthfulness and quality, plus consumer disregard.

When the handle on my expensive replacement (GE Profile for GE Profile) microwave/convection oven peeled, we called our retailer (PC Richards is really good about service). A new door showed up and it, too, has a plastic handle. The difference is, this time its solid grey plastic as opposed to white plastic with silver paint. Seems to me that an expensive SS appliance should have an SS handle. Too heavy? Just use a tube of SS - not solid. Too hot if above burners? Didnt my last GE Profile micro/convection have a SS handle? I spoke with customer relations. The person was well trained not to say anything that might suggest she agreed with me. Since the issue is cosmetic and not functional, I have to consider the issue dealt with now that the door has been replaced. I told them I will do my best to publicize this issue and that I will never again purchase a GE appliance. I also called CEO Jeff Immelts office in Connecticut. I made it clear that my dissatisfaction has cost them a long time, loyal customer and that I would spread the word. I would appreciate if anyone agrees with GE that a SS handle would be too hot over stove burners.

This microwave (jvm1540dm5ww) works fine but the plastic door is fracturing into bits. I expect this is because of faulty plastic in China. Cheap alternatives for fast profits. The machine is out of warranty. Replacement door is almost 160$ with shipping. Planned obsolescence by corporate America. This machine works fine but is a waste because I don’t trust the replacement materials to be any more stable. I rated this a two because the actual operation is fine. Sorry GE. I will not buy your brand.

Its been a decent dishwasher. Usually residue left on something. Even with rinsing. And weve tried all brands of detergent. Rinse, China, speed cycle, normal, pots/pans and anti-bacteria cycles. 9 hour delay and extra hot wash and heat dry settings. It works for our family. A load every 2 days or so. Its almond/bone colour. The hoses are flimsy. They seem like they could leak at any moment. Not sure Id buy another GE.

I own a GE counter-top sensor microwave oven model #JES1451, which was only 2 years old. At 3:00AM, I woke to a room full of smoke and a burning plastic smell. I immediately rushed to the source which was my microwave oven. It was going by itself and the panel read sensor error with smoke billowing out of it and flames erupting. Luckily, I had a fire extinguisher handy. I had never had any problems with this microwave prior to this experience. I cringe at the thought of what could have happened to my home and my family sleeping upstairs if I hadnt been nearby.

Bought our GE Microwave (DVM1850DMWW) from Home Depot about 5-6 years ago. I can see a unit just failing; but to start burning, smoking and smelling is non-excusable. We were lucky enough to be in the kitchen at the time and catch the problem before it escalated. While the unit was just ok while it worked, potentially burning down our kitchen is inexcusable regardless of age. Time for a range hood and a small countertop model. A non-GE model.

The wheels to roll tray in and out comes off sometimes, other than its fine, average wash cycle. Doesnt really clean heavy food off dishes so have clean first then put in dishwasher.

GE Microwave Model WES1450DN1BB 1.4 Cubic Ft 1100 Watt - This product is absolute garbage! This product was manufactured in June 2010 and I purchased it in approximately in May of 2011. So after 13 months of moderate use, the unit no longer functions properly. Needless to say, the product is out of warranty by about a month, so I pretty much now have nothing more than an overweight paperweight.I wont bore you with all the details, but for the most part, the touch pad stopped working and if left plugged in, the microwave will start on its own and run for up to a minute before beeping incessantly. If I unplug the unit and plug it back in, Ill receive a different error message, and so on. I wont waste my time contacting GE, because from what I hear, they really dont give a damn!When I was young, you could by an American-made product and expect it to last for many years. However, ever since greedy corporate America decided to ship all our jobs overseas in the name of profits, I have yet to find any imported products that are worth a damn. Instead of one good American product that would last a lifetime, I now have to purchase the same imported piece of ** many times over to get the same longevity. Maybe this is what GE wants?Needless to say, GE has now been placed on my Do Not Buy list. I guess I will now buy from another major manufacturer to see if their foreign-made garbage is any better!

Our GE microwave is used primarily for heating things though sometimes something is actually cooked in it. It is a useful tool and saves time and labor. I would rather have one than not.

To inform others that need an under-cabinet space-saving microwave, unless you are replacing an existing GE unit (and want the mounting brackets to align for easy re-installation), I would strongly suggest getting a different unit. I am about to buy my third GE undercounter microwave for the past 11 years. The rest of my kitchen is pretty high-end Thermadore, Kitchenaide, ASKO, and Braun. My last Profile PEM 31 DMBB lasted less than three years. The Toshiba that I bought while deployed to Okinawa lasted 15 years.

I bought a microwave Model JVM316RF3SS on 6/12/16 from Best Buy. Here is the serial number GG242212A. This thing is tripping the circuit breaker, it is intermittent. I had been buying GE for the house because the stuff would last or they would stand behind their products. Looks like times have changed, I called yesterday to the customer service and the only thing I was offered was a song and dance. If you are to consider buying a GE product, think about it again. This microwave is only a year and a half, to have a tech service guy come out and look at it, it is was priced out at $97-108 for a visit and then parts and time will be added in additional to this visit price.They have priced this repair out to be cheaper to just replace it. My washer is making excessive pump motor bearing noise during the high spin cycle, this is two years old. Looks like GE is building crap. My background is a mechanical technician for over thirty years, building products that are to be used in the household should be built to last not become a disposable item like a cigarette lighter. Good job GE for joining the other substandard products being built. Must be outsourcing this to a foreign country like everything else. With the model and serial number GE you can call me if you have ANY questions.

We purchased a VERY expensive GE dishwasher (Re: Case: 13259178, Model: PDWT580V00SS, Serial No:MZ841691B) for over $1500 and IT DOES NOT WORK! It actually DESTROYS dishes! It leaves a thick detergent film on plastic cups and plates and renders them unusable. We have scheduled no less than FIVE technician visits and all of them refuse to indicate that the dishwasher is faulty and needs to be replaced or they would likely lose their job. All they say in their report is that the dishwasher is performing normally. So a dishwasher that DESTROYS dishes is NORMAL? GE is a $265 billion company. They have a customer that is infuriated with a faulty product that they will not replace. They are giving us the runaround and it is unconscionable. Any other consumer focused business would have replaced their product by now. Not GE. They have a huge infrastructure built to keep consumers from getting their products repaired or replaced correctly. This feels like Davey Vs. Goliath but we are going to prevail. My advice to all consumer is to NOT EVER buy a GE dishwasher, unless they like to have their dishes ruined.

July 4th, 2010 - GE Profile Dishwasher, Model: PDW9200N00BB, Dishwasher had been humming after cycle was over for a little while, this night I walk into the kitchen late and find it full of smoke. Circuit board has a hole burned though it and wiring harness is melted. Never tripped any safety, could close the door and it would come right back on, smoke and all. This model was not on the recall list but I called GE anyway. After describing the fire they send someone out, then they send a new dishwasher out and install it. I assume they wanted the old one to look over or just to get rid of it. New washer installed the end of July 2010, new model number PDWT500R10BB. Today is 2012-02-02 and the new machine would not stop at end of cycle (Got down to 1 minute and stay there for at least 20 minutes before we turned it off). This machine is now making the continuous hum after the cycle stops that the old one did before it caught on fire.Called GE, they said they could maybe go half on parts and service until they checked where I was located. (Wichita, KS. Area population 500,000+) They said that they didnt send factory techs to my area and I would need to contact a local repair service. I pointed out that they had a factory guy for when my machine was on fire and they said it was just a malfunction now, so they could not. No half on the price for repair either at this point. This is a $1100 to $1200 dishwasher with, as near as I can tell from complaints online, a history of going up in flames. I understand things break etc, but when you continue to put out products like this and then refuse to remedy the problem, I and anyone who will listened to me will never own anything GE again.

Fact no. 1: On 02/25/07, I supplanted a burnt-out 12-year old Kenmore microwave oven. Regretfully, my replacement of choice is a GE JES1456WJ02 unit acquired at Home Depot in Cumberland. At that stage, my spouse was afflicted with an advanced case of Parkinsons disease, and eventually, I had her concerned caregiver reporting having found chips of paint spread on food extracted from the new oven. From that point onward, I established a close watch of the infamous appliance, after confirming that the chipping paint originated from the roof of the GE oven. But I withheld from filing a claim with GE at the time because my wifes health deterioration absorbed all my attention.Fact no. 2: But on 12/12/09, a couple of months after my beloved one passed away, I decided to take the oven to a Home Depot claim department where they immediately agreed to replace the defective unit for another one of similar characteristics. With a sigh of relief, thinking that I had taken care of the problem, my assumption was incorrect.Fact no. 3: Today, 10/28/11 in fact, I discovered chips of paint floating over a plate of soup extracted from the GE oven. I was aghast! I couldnt believe it! Still, further inspection determined that the lousy internal coat of paint is likewise peeling off from this monstrosity appliance manufactured by GE.

We bought the countertop stainless steel microwave model JES1142SJ the end of 2010. Noticed a rust ring under the revolving paint about a month ago. The paint was chipped off and when I washed it with a dish cloth, more came off. It is getting worse. We didnt stop using it since it seems it is only coming off under the plate but is it safe to continue using? Could it catch fire? Is it putting bad things in the food we heat in it? Even though it is not an expensive microwave ($100-$125) it should not be rusting inside. It should last longer than 3 years!Sounds like GE will not back up their products since so many microwaves owners are complaining about the paint being inferior and flaking off. There should be a recall for this problem on all microwaves sold by GE. Complaints have been from countertop to the most expensive dual stoves! This is not acceptable and GE needs to step up and deal with the problem with their microwaves that they sell. I usually buy GE; but this is making me have 2nd thoughts and think that my ones I bought in 2010 will be the last purchased from GE.They did come out twice for my range when the oven stopped working at 2 years and one of the eye knobs to turn on and off needed to be replaced when it would not turn off. But a 2 year old stove should not have needed any repairs. I noticed a big difference in quality after I bought this new one when we moved. My old GE from 1996 is still my favorite one and is still working just fine in my sons house.

My Profile dishwasher is not on the recall list, yet the heater element malfunctioned and did damage the entire inside racks and spin bar along with contents. GE told us to have their recommended repairman provide estimate. Repair guy estimated over $600 to fix. The unit was smoking hot which caused bubbling on the exterior and the dishes to show signs of burning. Well with estimate, GE is offering a discounted top of the line dishwasher for over $600. Pretty sure, I do not want another GE. Also, when I told the agent that I was afraid that if I had not been home, it may have initiated a fire, she said it would not have happened. Really?

Had 2 G.E. microwaves make a loud popping sound (like a boom) while turned off and then they started smoking like crazy. 1 model #JVM1630BB004/ serial#MA9713685. The previous microwave was just thrown away. I didnt realize there was a problem with these G.E. microwaves, so I dont have the other model/serial #s. These are a real danger.

First, as a new homeowner blessed with select builder-provided appliances, I never imagined I would be authoring this letter 4 months after closing on the new home. Your friggin’ microwave oven light mechanism truly sucks! I lost the two bulbs a week or so ago and purchased two more at the cost of approximately $10, even though a one-year warranty was stated. That was okay, as I was more interested in fixing the problem versus starting some long-range purchase interest. So, and this is the most aggravating aspect, I have the correct pins and life is ** good, and as I attempt to insert the first, the ** pin breaks off. Okay, so I reflect on the horrific engineering of the mechanism, and I softly” align the second of the two bulbs, and the ** pin breaks off again. ** is my predominant theme tonight. As well, believe me, I am going to inform Taylor-Morrison that their respective selection of your friggin’ lousy pieces of crap is corrupt and misguided. You suck, G.E.! I’m moving forward.

I have had the GE Profile for approximately 8 years with no Issues. I learn something new it will do every now and then I had no idea was possible. I stillHave not conquered the convection baking and that is my fault. I need to use it more often since it wouldn’t heat up kitchen like the range does especially these hot summer days in Texas.

We purchased several new GE appliances in August of 2016 as part of a kitchen renovation. We bought the GE Cafe series dishwasher CDT865SSJOSS. Within two weeks of use, the display stopped working. It took 3 weeks to get a technician out to fix display. Approximately 6 months later, we noticed the dishes were not as clean. Two months later the water stopped draining. Called a technician in, he diagnosed a broken pump. Parts would take 3 weeks and he would be out a week later. We are now over a month without a working dishwasher. He “fixes” the pump but says it isn’t draining great because your hose from your disposal is plugged (this hose drains to the same place as the dishwasher). Hire a guy to unplug the drain ($140). It isn’t plugged. The whole house is clear. Have to Shopvac out the stagnant water from the dishwasher that smells like a corpse. Call our plumber to check the lines ($500). He discovers that the technician pushed in the washer and busted a line. We now have water damage through our floor and into a bedroom below. He confirms that the plumbing is all clear and also finds that the technician never reattached the pan to the bottom so water was hitting the sensor and activating the shut off for a leak. Plumber fixes plumbing wrecked by technician, dries the sensor and attaches the pan. He advises that we run several cycles to flush out the stagnant water. If water still is not draining after several cycles, he advised that the new pump was faulty. Plumber leaves. We get 10 minutes into a cycle and the dishwasher stops for a leak again. I called GE hoping they would stand behind their product that we have now had for 2 years and have used less than a year. GE does not stand behind their products. The only thing they will do is send out a technician that you have to pay $100 for and they can’t guarantee that you won’t get the same technician who has come out 3 times and cost us more money due to his negligence. In May, we will be putting their terrible product out on our curb for city wide garbage collection. You no longer get what you pay for with GE. Do not buy their products!

GE had a recall but only gives you 50.00$ to replace it or fix it. We could not afford a new dishwasher. I talked to GE and they were no help at all. So we still use this machine but we do not run it unless we are home. This was the machine that would catch fire.

It works really well and this price point is good. It’s lasted me a few years and it is still in new condition. It has a nice modern look also. Good microwave for a great value.

Cost of washer $749.95 plus 4-yr warranty, install and hoses, $273 equals $1,023 for this GE stainless interior tall tub dishwasher GLD8700N20BB that only lasted 6 years and 4 months. It wont run, wont fill with water, nothing. Six years. Time to buy again. My advice, buy a cheap one and replace it every 36 months and forget the extended warranty. Installed: Sept. 2009. Dead: Jan. 2016. This was a replacement to an LG dishwasher that completely flooded my kitchen and caused a total tear out of my kitchen, and my homeowners insurance took LG to court. That LG cost $42,000 for a new kitchen and months of contractors and work. Washing dishes by hand is looking better every day... Think about it.

I also have a GE Profile dishwasher with malfunctioning wheels. I read this site, and was comforted and enraged that I was not alone with my melting wheels. I sent GE customer service a note, explaining my problem. I also included a link to this site in my note. I explained that I was a loyal GE customer and that they should stand behind their products although my unit was no longer covered under warranty and did not qualify for the recall. GE responded to my e-mail with in 12 hours. They sent me a complete set of new wheels for my bottom rack free of charge, and sent out a technician to install them, again free of charge. They also e-mailed me to make sure I was happy and no longer had concerns. I am thrilled with my experience. Let me say that again I e-mailed GE and within 8 days (a holiday included), I had new wheels and a technician to install them at no charge.

Purchased an entire line of GE appliances for kitchen after having prior (still working) appliances for 13 years. Have had at least 5 services calls and countless emails and phone calls for non functioning Dishwasher. Here is response from GE Manager: I have reviewed the pictures and no I would re-wash those 4 dishes if they came out of my dishwasher prior to using them with my family. Dried on fruit, starches and dairy are tough for any dishwasher to take off as the sugars in them act like glue. Again for these types of foods we would highly recommend more pre-washing to make sure that they are not left on the dishes after the dishwashing cycle. CAUTION: DO NOT BUY.

My less than a year old GE microwave stopped working last week. My AT&T phone service died so I had to make repair arrangements online. Guy was here this morning. My microwave’s main board is fried. It does not conform to Repair Guy’s published schematics. Repair Tech could not upload new data to it. Repair guy did order three new parts including a main board. GE told Repair Guy that mainboard delivery ETA UNKNOWN. After three hours here repair tech left and told me to call GE customer care. Believe it or not, two hours on telephone with GE. First you need to talk to a customer service rep that cannot help you. They then determine you need a Customer Advocate. Then they need to input data on your file for the Customer Advocate.Then they need to transfer you to that department. Then you have to get a case number assigned. Then you give someone all the serial numbers and model numbers again. Then the Customer Advocate (CA) takes the call. The CA does not speak English as you and I speak English. After the CA puts me on hold to verify the purchase, then the appointment, then the tech and then the order they actually speak to me. In my case, the mainboard part is not available on CA’s computer. The CA has to electronically contact the parts department to find out if the part is in this universe. If the part can be delivered to my Repair Guy in Jackson, GA within 14 BUSINESS days from the date of the inquiry I have to take the part and wait for repair.In the event the part cannot be delivered in 14 days CA will start a process to get me a new microwave. The parts department has up to 48 hours to respond to the CA. When asked what happens if no response occurs in 48 hours, I was told, That never happens. It is the Christmas Holiday and I anticipated guests. My husband is disabled and his meals are pre-made frozen so I will have to decompose them and heat them on the cooktop. GE could care less about those issues. So after waiting five days for repair I have no working microwave. Someone told me not to replace my GE with a GE, but I did not listen. It is December, holidays, no microwave is an aggravation that I thought paying for a GE product would alleviate. So, on January 2nd I might get an answer. Part possible or new appliance COULD be ordered and delivered by someone sometime.

I have a 2011 GE Model # JES1456BJ05 microwave and it has been gently used and kept clean. Upon cleaning today I noticed that the top of the inside is blistering and peeling off. Surely this is not safe as it could fall into food, plus they should make them to stand heat, after all this is why they are made for heating things. I called GE who informed me that there is no recall on them so I am pretty much stuck to go out to buy a new one with no help from them. I now read that this has happened to people before. Lesson learned never purchase a GE microwave as they do not stand behind their products when a manufacturing problem develops if you are the first one to call, and beware and ready to buy a new one every 2-3 years. This is all they are made to last!!!!!

GE microwave turns on by itself, creating a fire hazard. We could not figure out how our plastic plates melted, until we witnessed the GE microwave turning itself on by itself. Also filed a report with saferproducts.gov. It may have to take a death of a human to have this dangerous product recalled by GE. Great business plan, GE!

My microwave also began peeling under the glass within a few years after we purchased it. I contacted GE and they claimed they never heard of that type of complaint before and there was no recall. I knew it could not be just my appliance that was doing this. It is peeling A LOT under the turning dish, but unfortunately I cant afford to buy another oven/micro appliance now. When I can IT WILL NOT BE A GE!!!

We purchased a new General Electric (GE) Adora microwave model DVM1850SM4SS from Home Depot for approximately $355.00 in 2010. It was manufactured in Malaysia and had been in use for 2 years and 9 months before the magnetron failed. I spoke with a GE Customer Care representative on two occasions, and she said that the best that GE could do was split the cost of parts and labor since the 1 year warranty had expired. We had not purchased the extended warranty believing at the time that a microwave generally lasts for many years, and GE had always made quality products and would stand behind them. I indicated that I wanted to have the problem properly diagnosed by the service rep recommended by GE before proceeding further. The 10-minute service call bill set us back approx. $100.00. It would cost at least another $170 to replace the magnetron if we used the service tech contracted by GE. For $270, I believe we could find a fairly nice new microwave. I looked at alternative options for repair or replacement, since I am rather partial to the looks of the over the range stainless steel Adora. The model we have is no longer manufactured, but GE now offers the 1.9 cu. ft. Adora that Home Depot sells for around $400.00. In my internet research, I noted several postings that indicated that due to the high voltage danger of the magnetron, only trained technicians should attempt repairs. After half a dozen calls, I fortunately learned of a Microwave Service Center close to our residence that could replace the magnetron. After taking it down from above the range, hauling it in for repair and paying the approx. $104.00 bill and hauling it back to our residence to mount on the wall, we have a microwave that should work for a while! Total cost including service call for diagnosis - $204.00. Considering that GE does not wish to stand behind the quality of their products, I would not be likely to purchase a GE product again.

Less than three years ago, I purchased a microwave oven wall unit to replace an existing unit. Due to the size of the built-in cabinet, I was limited in choices. The cost of the unit was $2400. A few months ago, the interior wall of the unit began rusting and the enamel is peeling. I contacted the customer service dept via e-mail on their site. I was asked to send pictures and then informed that I should stop using the unit immediately due to the danger of arcing. I was also told that because I did not purchase the extended warranty, the best that GE could offer me was a new unit for $800. I asked for names of warranty companies and was given one name and number but told there were others that also offered the same service. I called this company and they clearly told me that the peeling and chipping was a manufacturer’s defect and would not have been covered by an extended warranty had I purchased one from any company. Then I contacted the GE repair service center and spoke with them. The man who answered explained that this is a cosmetic problem and that there was no danger of the microwave arcing unless there was less food in the microwave than the size of the area that was chipping. I am very disappointed in the response of GE, the pressure placed on me to make a decision in 7 days or the offer would be withdrawn, and the fact that the service department and the consumer service (complaint) department gave me entirely different responses to the same information and problem. I will probably have my cabinet rebuilt to avoid having to replace this unit with another GE appliance. Who would pay $$1600 for the use of a microwave/oven unit for less than three years? Unfortunately, GE seems to be the only company that makes a unit that fits the existing cabinet in my kitchen. Disappointing to say the least.

We have an under the cabinet microwave oven. I like the size of it and it works well. It is white so it gets dirty from cooking on the stove. It has a light on it for 2 different lighting needs. It has a brighter one and one for night time also. The buttons are really easy to use. Not hard to program it at all.

I have a 15 year old washer/dryer set that has worked consistently and it resides at a rental property. I purchased GE washer/dryer set for primary home 4 years ago and it's awesome. It's the level 1-2 steps above basic model and has enough settings to fit my needs (maybe more than I even use) such as pre-soaking, 4 settings for loads and much more. I would not purchase anything besides GE appliances. Very reliable and easy to interface with.

We have a GE Profile Microwave/Oven combo unit. The paint is flaking off inside the microwave. Most of the ceiling paint is gone, and the floor of the microwave is flaking. Because we have a combo microwave and oven, the entire unit must be replaced. Thats around $2400. We cannot match the color, because they dont make bisque appliances any more. GE customer service suggests we replace the microwave with a countertop model, leaving the dead microwave on the wall. This is unacceptable.

Lousy and wont clean dishes. $1,000 down the drain.

My microwave (model#JES1139BL03 and serial#901897B) is peeling around rolling fixture that holds glass tray. I wipe it with hot water and it continues to peel off. Its almost all gone. Ive only had it two (2) years. This cant be normal. Anyone else have this happen?

After only 4 hours of installation, the microwave turned on and the fan and light came on. It was not cooking anything. Inside of microwave was hot and I could smell a burnt electronics smell. I unplugged it, waited a few minutes, and when I plugged it in, it started up again. The LCD screen was scrambled, all lit up. Opening the door stopped the unit, but it started again when I plugged it in.

It is about six years old, great dishwasher. The bad part is the new detergent! GE profile, pre-rinse, preheat water, everything, including enough water. Hold everything, unfortunately, now aluminum must be hand washed. Good looking, curved front. Its great, I shudder to think what the new low water usage ones will be like. I HATE my new low water usage washing machine. I HATE the reformulated dishwasher detergent, can be used on anything aluminum, now I use lots more water hand washing all aluminum items!!!

Our $599 GE dishwasher of 3 years is literally falling apart. We have a GE Slate Colored Stainless Steel Interior Dishwasher (GDT580SMFES) and over the past two weeks, the water stopped heating and 2 seals in the dishwasher started disintegrating. If you touch the seals (the main gasket at the bottom of the dishwasher and the main seal that keeps water from leaking outside of the dishwasher), parts of the seals come off on your fingers. We bought our dishwasher through Lowes with the extended protection plan and were having a hell of a time getting it fixed... Every time we call to make an appointment, its a minimum of 15 minutes on hold and it takes FOREVER for the new part to arrive/get the new part installed (almost 3 weeks now). So disappointed in our appliance and in Lowes for selling us such a lousy extended warranty. Never again!

Bought a new GE microwave cafe series in May 2014. Within one month the handle which was not stainless steel started to peel and cut my wifes hand. GE sent a replacement new door for the unit that did not close. Then he had to transplant the handle from the new door to the old door. A month later the unit failed. A new replacement unit took 2 months to replace. It has worked 3-4 weeks and has also now totally failed. Our experience with GE CAFE microwave and GE service process is poor to miserable. I would not recommend this product or their service to anyone.

I recently purchased a GE Profile 1.9 microwave oven from Home Depot less than a year ago. Last week I went to remove something that I had cooked and went to close the door and it would not stay shut. I ended up getting some masking tape to try and tape it shut in order to keep the light from staying on and burning out until morning when I could get a better look at it, thinking that it had to be something small that could be taken care of without any problem. Hinge adjustment, something getting in the way that I couldnt see, etc, etc. Wrong! I have been over this door with a fine tooth comb and there is nothing that I can see that is preventing it from staying closed, not only that but according to everything that I have read, I am very lucky that I didnt get fried while trying to figure out if the latching mechanism was functioning correctly. I am not even going to go through the long drawn out process of dealing with GE over this due to the simple fact that I have been there done that with my dishwasher that showed up with the front panel dented a few years back from the factory and I ended up blaming the place that I had purchased it through instead of GE and have since found out by reading other complaints that this seems to be something that is not unusual when it comes to GE appliances. I spent over 1100.00 dollars on the dishwasher and they only replaced the panel instead of giving me a new one, and I have never been satisfied with the way that it operates, and it was a very long and drawn out process and I am just not willing to spend the time again on another one of their products. It is unfortunate that we have entered a time where customer satisfaction means nothing, and the days of caring about having repeat business from a satisfied customer are over. The prices continue to rise on the things that we have become to depend on and cant seem to live without, but the quality and workmanship have not only diminished but also present safety threats. I will never purchase another GE anything and I am looking forward to the day when we all have finally had enough of this and do something that makes these companies stand behind the products that they sell and quits ripping the consumer off. Its rampant across the board no matter what you buy, and there should be laws in place in order to keep it from happening. We have laws for everything else, why not have a couple that protect the consumer and their pocket books.

GE Profile Advantium 120 when cooking on stove under microwave, the fan in the microwave goes on and does not go off for 30 minutes. This happens with only one burner on and stove not microwave set at 320. Had service out told there was nothing he could do. Called GE and again told that there was nothing they could do.

GE Dishwasher Model GLD7400R10BB - Remodeled my kitchen about 2 1/2 years ago and replaced all my appliances with GE appliances. I noticed that every now and then my dishwasher wasnt starting or running through a full cycle. I had called the GE repairman because my microwave was not heating up and asked him to take a look at my dishwasher as well. After hearing it was going to cost me $500.00 to fix my still under warranty microwave and the control board was no good and very expensive to replace because my one year warranty had past on my dishwasher, I will never invest in the money hog GE ever again! WARNING... DO NOT BUY GE!

The GE microwave installed in my new home caught fire on its own. It is less than 3 years old. GE Consumer Relations Department refuses to replace it for free even when it caused a fire accident on its own. GE microwave failed in its safety standards. GE also has failed in its Consumer Relations. I will not trust GE brand again.

One day after the new GE dishwasher was installed, I came home to find water raining down into my basement. My kitchen floor was destroyed. The installers came out a week later to look at it. They determined it was a faulty unit. They ordered another one. I started an insurance claim with GE. They sent a technician to look at it. 2 1/2 weeks after it was installed, the technician showed up. Surprise, it was leaking anymore (The water had been shut off for 2 weeks). Several days later the replacement unit arrived and was installed. Two days later, this one started dripping. I called to have it removed. The installation crew was scheduled to come back on Saturday to remove the dishwasher and get it out of my house. On Thursday, this unit started pouring water out onto my floor. The occasional drip had become a steady stream of water. More than a month after buying this hunk of junk, it was finally removed. Ive ordered a different brand of dishwasher. Ive hired a contractor to come and replace my floor. GE denies any responsibility. I will be starting a lawsuit against them. I cant say enough horrible things about dealing with GE.

My dishwasher broke within warranty in April 2014. The warranty expired on April 29th, 2014. Every 2 weeks another part was ordered to the tune of 10 parts and 8 visits (unpaid work days for me). I have been in touch with consumer relations about this and I was told that this would go on forever until their techs deemed the dishwasher as unrepairable but as long as it is repairable, they will not exchange the machine. And now they are telling me (October) that I could have had another service provider fix it but I would have to pay for it because NOW it is out of warranty. I cant wait until I replace my GE refrigerator and my GE microwave because those are the last GE products that I will ever buy. I went out last month and bought another brand as I will never buy GE again. GE protocol I am told is what determines all that happened. I suggest you do the same. I am writing a long letter to GE just to get it off my chest. Nothing will be done because its another corporation all about the money!!!!

I am now facing my 5th repair appt about my 2 year old microwave. I have spent nearly $300 on repairs to be told I can purchase a new one for 50% off. Well, $426 plus my $275 I have paid IS A NEW One! 20 hours of me having to be available for service. I did not know the life of this appliance was 2 years. GE complaint number **. This is an unacceptable resolution offered by GE!

Model gdt580sgfbb - About 2 weeks after the warranty expired, the dishwasher stopped filling with water. So, our friend replaced the water inlet valve. No change. If you pour water into it, it kinda pushed it around, but empties it out, wont refill, and starts whining. Then, if you open it, and turn it off, and re -shut it, it starts itself back up again! What?! This stupid thing is essentially brand New! To be truthful, it has never cleaned very well, leaving residue on dishes, and NEVER getting dishes dry. I regret buying this item! And its still not fixed. I will not buy another GE appliance.

Figure it out GE! The sixth motor and mode selector for our washer has been reluctantly ordered by a tech this morning. The second motor was installed months after buying the brand new machine. Now, only two months since the fifth motor and mode selector was installed (Dec 2, 2011), the wiring harness is burnt up. The tech recommends replacement of the washer by GE, but only gets push-back from GE. This newest incident included a horrific smell of smoke. I do not trust this machine. I have a wife and child to protect. Think about it - do the math - add your costs for repeated repairs. You do not get to be a company the size of GE by not understanding simple economics. Open your eyes and replace our washer.

We moved in to our home in 2006 and it had a GE Monogram Microwave built in. The microwave died and I purchased a similar GE Monogram microwave to match our kitchen in 2014. That microwave died exactly 17 months later. Fortunately, we had a home warranty program as we are selling our home. I figured that this saved me the effort to complain to GE about their product... Wrong. The Home Warranty program sent a repairman who said we can order a part. A few days later I received a call that they would replace the microwave. OK... I checked online as well as with a local retailer to see which model is the replacement model, and trim kit. Today (about 10 days after I first called for service) they delivered the new GE Monogram microwave and installed it. Fortunately, I asked to test it and we tried to boil a cup of water. The contents in the oven being cooked were not visible. Either the light was too dim or the shading on the door was too dark. I have never seen a Microwave where you could not view what is inside. I called GE Customer Service while the installers were there and they refused to allow me to keep it until a replacement was delivered. They had to deinstall it, re-install my old (non working unit) and take the new one back. I called GE with my homeowners claim info and they sent me back to the Homeowner Warranty company to start the claim all over. Ridiculous.Instead of a replacement they offered me a cash value which was 60% of what I paid the retailers. When I asked why that amount? They only provide the value based on what the Warranty company gets the products/services for (wholesale cost). Net: If I used the money to buy another product it would cost me out-of-pocket for replacement. I am hoping the new unit to be delivered in the next 3 days works better. Otherwise, GE has a significant design flaw that doesnt allow you to view what is cooking in the Microwave. If thats the case, why have a window at all? Fyi - My Panasonic Microwave in our basement is working fine.... and has for years.

Our stainless steel finish 1100 watt JES1142 microwave is around 2 years old. Within the last year the finish inside started to corrode (yes, my wife cleaned it regularly with a non abrasive, appropriate cleanser). Also, the door latch button started sticking and a few days ago it just stopped heating. Unfortunately I cant find my receipt, but I bought it at my local Lowes on Bell Rd. Nashville TN. Serial # is MA212483G. Manufactured July 2013. Was this just a lemon? Very disappointed.

GE Profile GLD4408RBB: Bought this dishwasher at Home Depot 2010 for our FL condo. We visit there periodically, dont rent out. We have used this dishwasher probably 50 times since buying. It never wash dishes well, leaving residue and we do clean them first. Now it doesnt drain; seems like pump not working. Its only five years old and hardly used. Its not worth having a repairman for labor and cost of parts. Very disappointed with GE product and wont buy another one.

I purchased this dishwasher in Sept 2017. Today after normal use, the motor stopped and it leaked a full load of water into my basement. I called GE service and got no satisfaction. Its out of warranty after 12 months. I then called their customer care department who really dont care very much. They wanted a GE tech to look at the dishwasher for a fee of $109. Then they offered 50% discount on parts. In the past, GE was always a reliable brand but no longer. Stay away from their dishwashers and every other appliance they make. It is not the GE of old. I just purchased a KitchenAid dishwasher and hopefully, that will work better.

The GE repairman just left. It wasnt the coil that was flaking, it was the eco dish washing detergent I was using. The detergent wasnt dissolving, it was clogging up the jets and burning on the coil. What I was seeing was black burned detergent flakes. The repairman gave me citric acid to use to clean out the clogs (for free). He also didnt charge me for the visit, even though it was my fault. He also told me to get the water in my sink really hot before I start the dishwasher. I am very impressed with his service!

Within a year and a half of buying a new construction condo, the GE microwave fan stopped working (used the condo for no more than 30 days). I read all these complaints and am not surprised. My experience with Kitchen Aid appliances (refrigerator, microwave all junk) is no different than this. If I were to replace any of my appliances, I will not buy an American brand because they are all made in some other country with very poor quality control for very high profit and low quality goals. No choice for now, other than to get it repaired. At least, it provides employment, but what a way to create employment. I would never work for such companies.

Bought the new dishwasher in Dec. 2013. In November 2014 a month shy of warranty expire, the detergent dispenser did not release or partially released the detergent. GE sent out A&E Factory service to fix. First visit initiated the parts order which was a new computer board and a Cascade Series detergent dispenser. A month later the second visit to install parts, the A&E tech was at our home for 3 hours and it took that long to remove and replace detergent dispenser. The tech did not replace computer board stating it was not needed? A week later the detergent dispenser still did not release the detergent! Called back to set up another appointment which was at the earliest Jan 19th 2015. Meanwhile last Friday Jan. 9th 2015 the dishwasher started to smoke heavily causing smoke detector to go off at 9 p.m. at night. Thank goodness!! We were home so that I could disconnect the power. Third visit was 1/12/15 and was informed by Lead A&E tech that the board should have been replaced and that the tech that was sent out was a trainee and inexperienced to work on my dishwasher. He should of never worked on my dishwasher(!!) according to the Lead A&E tech. The Lead A&E tech also stated that my model has had a problem with the computer boards which is essentially the brain of the dishwasher. I am currently taking my fight back to GE since A&E Factory is a subcontractor to GE and is not authorized to replace appliances. I told GE that I want a new dishwasher that is not using the problem computer boards even if it is an upgrade. It is not our fault that they have work with A&E who send out inexperienced techs to work on complicated GE appliances. We want a dishwasher that we both feel safe to run while we are not home. Is that too much to ask for?

In 2008 I redid the entire kitchen and purchased all GE Profile stainless steel appliances thinking I was purchasing quality items. Well, it didnt take long before the dishwasher broke but it was fixed for free by GE under a recall. However, now the refrigerator has begun to leak under the right corner of the ice/water dispenser located on exterior of freezer door and the microwave touchpad has also failed as I need to press below the actual keys for it to work half the time. When I spoke with GE customer service they basically told me there was nothing they could do with the refrigerator, I would have to call a repairman and have it looked at or pay their $100 diagnosis fee.The microwave they told me had issues with that particular touchpad and had it broken within first 5 years they would have repaired it for free under their recall program. But since its 7 1/2 years old I would have to buy the touchpad which normally only lasts for 6 months to 1 year or buy a new GE microwave and they would offer a rebate. Im so unhappy with their customer service and poor reliability of their products that Ive passed on each offer as I dont want to contribute another penny to a company that in my opinion is unethical and has horrible reliability. 3 out of 4 of my fancy GE Profile stainless appliances have broken! Thats a 75% failure rate! No thanks, Ill buy elsewhere. No wonder they cant sell their appliance business and why the stock hasnt moved in years... Wake Up GE, do whats right for your customers!

Microwave Model HVM1540LP1CS... This microwave was installed 6 years ago when I built my home. I live by myself and the microwave has only been used by me. I loved this microwave until suddenly it began to turn on by itself and I would often hear popping noises. I looked up reviews of this GE microwave and found that this is a frequent problem with GE microwaves. Fires were reported in a couple of reviews so I immediately unplugged mine, as a safety precaution. If this happens frequently with these microwaves, why isnt GE replacing the parts for the defective machines since they can be fire hazards?

In late March, we placed a service call under GEs one year warranty. The outcome - a gasket repair. Within a week or two, the door began to drip from both the right/left bottom. With having three teens, I figured someone opened the door and released some water. Well, that just wasnt the cause. Shortly over the next few days, the leak was consistent and I placed a service call to GE on 4/19. The customer representative offered, instead of a service call, to order some panels that fit it the bottom of the dishwasher. I stated clearly that our one year warranty was up on 4/25 and if this does not work, would GE address the issue with a service call? Answer was yes. Within a few weeks, I began to worry when I did not receive the panels. A call to GE was made; however, no documentation was noted of the call made on 4/19. However, GE stated the information might be in parts department, but regardless now, that call was made after one year warranty, extended warranty would fix the issue. Long story short, the extended warranty states problem initiated under GE and GE states the extended warranty is responsible because the call was made outside the one year warranty. I expressed that GE never fulfilled responsibility as GE did not even notify us that panels were not available for our unit. In the meantime, I am the one out of a working dishwasher. Now I know $539 may not be a lot to invest, but we feel the loss. The frustration and lack of responsibility to correct the repair is just beyond me. GE is responsible. Oh and did I share that lack of communication with GE is horrible? A promised call within 12-24 hours just doesnt happen. Again, I know most would say its not worth the frustration, but it makes me sad that GE and Assurant Warranty company can get away with what I know is wrong. Weve learned from this ordeal. No more GE products in our household.