We bought a GE dishwasher a little over 3 years ago. In the last week of September we awoke to the smell of hot or melted plastic. We found the source to be the dishwasher. I had loaded and started it before going to bed the night before. The counter-top above the dishwasher was stove top hot and upon opening the dishwasher found that a cutting board that we have had for many years and have always put in the dishwasher had melted on top of the heating coil. Dishwasher safe items on the top rack melted as well. It had been drying for at least 9 hours. After pulling the dishwasher out we saw the heat shield had melted and was crumbling. We contacted GE, sent them all the pictures and they told us it was not a safety issue. We have no doubt that if we had not woken up so early we would have had a fire in our house caused by the dishwasher.

It could clean better without pre-cleaning. Its necessary to pre-clean heavily dirty items. Works ok if dishes are just moderately dirty. Could also be quite a bit quieter. However it is about 15 years old and still running but sometimes motor freezes up if not run often.

Our GE microwave does all the things you would expect from a basic microwave. It cooks vegetables, reheats leftovers and warms coffee. It looks nice on our counter. Do I think it is worth the money we paid for it, NO.

We bought a model PVM9215SK3SS microwave as part of an over-the-range microwave oven/extractor fan combo. Unlike every other microwave combo weve ever had in our frequent moves, this microwave cannot run the kitchen timer independently of the microwave. If you try to set the kitchen timer when the microwave is running, the cook-time changes and overcooks whats in the microwave. If you try to set the microwave to cook while the timer is timing a food cooking on the range, it simply refuses to work. The instructions are very hard to both find and then understand, having been written in China to cover many different models. Apparently I can ask my phone to turn it on. I sure cant manage that very often in person! The fan is too loud for comfortable use even at the lowest speed, which is a great disappointment. A former Profile model was very quiet at every speed, and much more efficient. Were saving up for something that works.

I purchased a this GE Model CDT845P2NS1 on Oct 2, 2019 and the unit was received Oct 23, 2019. I installed the unit approx. 4 days after receipt and dishwasher functioned well until November 10th, 2020 when the unit failed to pump out the water. I contacted GE Service (MabeService) and was advised that the unit was not under warranty and as such I should contact a GE Canada authorized service centre.After several attempts to get someone to come to our location at Sharbot Lake we got hold of Capital Appliance Repair in Ottawa. They were not able to send a technician until November 18th. After diagnosing the problem the technician advised we needed a main control board and would have to order one and then come back to do the install of the control board. It is now February 21st 3 months after the visit and I’m being told that the part is backordered and they have no idea when it will become available. I’m extremely unhappy when you spend over $7,000.00 for a GE CAFÉ gas stove, Microwave, Refrigerator and dishwasher to find out you cannot get parts in a timely manner. As a customer of GE Canada I have had no help is solving my problem. It is not acceptable to have a 1 year old dishwasher that has failed, much less waiting for repair that has taken over 90 days to get repaired. DO NOT BUY!

GE microwave oven (jes1651sj02) started to spark like lightning, which can be seen through the inside vent grid/grill located on the right. Sparks are seen just behind the waveguide cover where the magnetron is located. It seems to be a common problem with GE microwave ovens from what I have researched. The microwave has now stopped working and just makes an odd noise like groan or urrrrr. It’s just over 2 years old. Its a piece of **. It should last 10 years or more, like my last 2 have. I gave away our Sanyo because it wouldnt fit the decor of our new kitchen - wished I never had.

4th service call for a piece of ** over the range microwave that keeps breaking. The service is a joke too. The sent some moron to come take a look at the microwave after I placed this latest service call. He came and without diagnosing, he ordered a few parts and scheduled a follow-up for today. He called this morning to reconfirm the appointment (which was already confirmed 2 times previously and this reconfirmation has never taken place previously) and I missed his call. When I called him back short whIle later, his voicemail directed me to call the 800 #. After a 35 min hold with them, they said since I didnt pick up the phone in the morning, the appointment was canceled. What???? It states nowhere that theyll call you to reconfirm an ALREADY SCHEDULED AND CONFIRMED appointment and that if you miss the call, they cancel the appointment. Next service call is a week from now, which makes it 3 weeks without a microwave. I hope they rot in hell.

I had a blow up with my GE microwave which came with 2 metal racks. I used the rack once and the microwave flared up as if I had warmed something on aluminum foil. I removed the racks. The microwave is 2 years old. Last week I warmed a chocolate chip cookie on a paper plate for 10 seconds. Immediately the microwave flared up, the plastic bracket that the shelf rest on burned and melted. I was lucky no one was hurt or a fire resulted. GE came to inspect the microwave and offered to replace it for $258.80. I am arguing with GE. I want them to replace it free of charge. Their own technician tells customers to never use the metal shelves. I maintain that the design or brackets are faulty and GE should stand behind their products. This microwave was always used correctly. Do consumers have any rights at all?

This is one hell of a dish washing machine. You really need to think about getting in on this thing at the ground level. You put the dishes in dirty and they come clean! Holy**!

GE over the range microwave JVM1540DP1WW - Within 1 year, the magnetron failed. I called the Sears service department to fix it. Because of that, I bought 2 more years of extended warranty. Three months after that, the microwave turned on by itself for 1 minute nonstop. I had to unplug it and call the service again. It would also turn on even when the door is open. Its very dangerous for microwave exposure!

I purchased my new home equipped with all new G.E. Profile stainless appliances. Three years after that, our microwave (model number JE2160SFS01) had the magnetron go bad - no problem. I called G.E. and had a tech come out and replace it ($79.95). Great! 4 years later, it goes out again. But it’s still covered under warranty (cool). I call them, set up appointment, and ask what the charges will be - $79.95 home service fee. Fantastic! I schedule the appointment, and three days later, a technician comes to my home. I tell him it’s the magnetron, and he turns on the microwave for a second. He says yup and types his diagnosis into his laptop and prints out his estimate. He hands it to me, and it says “Total amount $ 270.10”! On a covered part!I asked him if he was joking, because the M.S.R.P. for that model, which I got from G.E., is... wait for it... $269.00 for the whole microwave oven! I threw the tech out and called their consumer advocate line (which took over an hour to talk to a human) and asked who sets their pricing for repairs, and was told their senior technicians set the labor charges! It’s a twenty-minute job! $190.00 for twenty minutes? So the tech left with $79.95 for doing absolutely nothing! Great job General Electric! I will never buy another product from you again! By the way, the magnetron they say is priced at $142.30 is available online for $97.50! It takes twenty minutes to replace, and a monkey can do it!

After one repair to my 9 year old microwave we decided to replace it. I am so sorry I did! The old microwave had a stainless steel kit and was made with quality. The replacement is a piece of junk! The outer kit is plastic and shows fingerprints like crazy as well as the microwave itself! Im always wiping it off. The flimsy door button is impossible to open without pushing it ten times in the right spot! The door doesnt close easily either! The front of the microwave is warped and wavy! I hate it! The quality of your microwaves has dropped to zero!

We selected this microwave because it has a toaster and baking feature as our small kitchen would be better without a toaster oven taking up space. Turns out user must change accessories from glass to metal when using the toaster and baking feature. The space needed to store accessories rendered the space saving concept as useless. Also, the toasting is slow and does not quite equal what a toaster oven accomplishes. Also the baking/convection mode is so noisy, one cannot hear radio/tv. 30 minutes for a baked potato is a long time for excessive noise. We bought from Kitchen Solutions in the Bronx about May 2014.

Called out GE service tech to diagnose my dishwasher which was not draining after the wash cycle ended. Was told it was the control board and it would be best to buy a new dishwasher. Purchased a control board online (was a GE original part for a lot less than the GE price) but it did not solve the problem. After researching the problem online, I found out that it could be the drain valve. Sure enough, bought one for $14, installed it myself and the dishwasher works like new. Called GE Service to try and get a refund for the service visit ($89), was told that I had 30 days to have the tech come back out at no charge. Tech never advised me of this policy and GE will not refund my money.

Remodeled our kitchen back 6-7 years ago and bought GE Profile appliances from Home Depot... bad mistake. The microwave/convection oven came as one unit and now due to paint peeling on the microwave interior - inside top and sides we need to replace the entire unit to the tune of $2,500 plus. I called Home Depot and asked if there was a government mandated recall on the item... and they asked if we purchased the extended warranty. What? Does anyone know of a recall or class action suit on the following item: GE Profile Model: PT970SMISS. Manufactured December 2007.

I purchased this GE Profile dishwasher last June, I paid $1,499.00 for it and have had three (3) service calls. The first one said the water is not hot enough, the second one said run the water in sink and get hot before you use the dishwasher. The tech was here again this morning and called in to tech services and was told put plates on the right side of the rack only and the dishes will get clean. Are they kidding me? I called the 800 number for customer service and was told by Dominic (rep in customer service) that they would replace the dishwasher and allow me a 40% discount on a new one because this one is working as designed. It is my understanding that the dishwasher should wash dishes, so that tells me it is not working as designed. I want a new dishwasher, preferably one that washes the dishes and not one that I have to pay an additional 60%. Are you kidding me? This is not right. I have read the reviews on this dishwasher and it seems everyone who purchased the dishwasher I have are having the same problems and it is not working as designed. Please let me know asap when the replacement dishwasher will be delivered. I will not pay an additional 60% for another. It is not right that you would keep making excuses until warranty runs out. I notified you of this problem one month after I purchased it and I have lived with this problem for almost one year and now you tell me that you will give me a discount on a new one. I have already paid for a new dishwasher and that is what I expect in return. Thank you. I expect to hear from you soon.

My Microwave that is four years old suddenly wont heat anymore. It still runs but there is no heat. They told me its out of warrantee already. The repairman says its the magnetron and it costs $600 to replace! The oven microwave combo unit is $1500 altogether to replace. I bought another Walmart microwave for $47 and it works great! GE will not replace or fix it. They dont stand behind their products and are not helpful on the phone. I will never use a GE product again.

Last fall, we updated our kitchen counters to quartz, and the Jenn-Air to a GE induction cooktop. While it is indeed pricey, the joy of cooking is not overstated here. The quick heat up, the ease of controlling the heat more precisely, and the easy clean up makes this unit well worth it. I love it!

Door would not latch, so entire locking mechanism was replaced. Still wont lock. Repairman said it looks like door is warped or bent and door may need to be replaced. We have used the dishwasher twice a week for a year and suddenly it wont lock. Have heard this is a common issue. Is this true? Is there a recall?

I just renovated my kitchen and purchased all new appliances. I had stopped buying anything GE because of the poor customer service and inferior appliances. After more than 25 years I thought I would give GE a second chance. What a mistake. My new microwave clunks every time the dish inside spins. GE sent out a repairman who said he fixed it. As soon as he walked out the door, I realized it was never fixed correctly. After waiting on hold with GE for over 45 minutes today, I was told that they will send another repairman out. If he finds it isnt repairable then he will send that info back to GE who will try and figure out how to fix it. If it cant be fixed then I will get a new microwave. It is a new microwave that was defective. I dont want this microwave because it has been defective since day one. I purchased my appliances from a local family owned store. GE has a policy that they (GE), are responsible for repairs for the first year and then the company I purchased the appliances from will do any future repairs. I will never buy another appliance from GE. They still have the worst customer service. Ridiculous how terribly they stand behind their appliances.

I work as a service tech for a major insurance company. I am a master tech, and master electrician. The company that I work for owns an apartment complex which is used to house company executives whose offices are located at other sites, but often come to the Chattanooga Site to work short term. I was called to repair an old dishwasher in one of the apartments. Upon looking at the existing dishwasher, I decided to replace with a new one. I received a new GE model GDF 510 PGD 1WW dishwasher on November 8, 2013. As usual I unpackaged the appliance and examined the exterior. Finding no visible damage, and with the help of a master plumber, I removed the old dishwasher, and installed the new one. After all the connections were made, I opened the door, removed all the packaging from the dishwasher, and found the upper spray arm lying in disarray in the bottom of the machine. Assuming that this was the way that the machine was packaged, I installed the spray arm, plugged the machine up and started the machine as the operations manual instructed. The machine would not work. The power lamp would burn solid for a few seconds and start flashing. I tried to start the machine a number of times while reading the instructions, and while my partner read the instructions aloud, but with no results. Finally, I used a screwdriver to hold the door switch closed, pressed the start button and the unit started. The catch mounted on the door would not make the door switch, mounted on the machine body. We tried to adjust the switch and the catch, but with no success.The dishwasher did not show any signs of exterior shipping damage, but for some reason the upper spray arm was off and lying in the bottom of the unit, I found a small piece of broken plastic and a screw in the bottom of the machine, and the door switch would not make. Outside that I have no complaints. I am not sure where this machine was assembled, but it certainly was not equal to the machine that we removed. Thanks GE for making my job harder. I will have to find another dishwasher Monday and replace the damaged one, and perhaps send this one back, but the replacement will certainly be another brand.

I have owned my dishwasher for 5 years. Monthly, I use dishwasher magic to clean the inside, removing lime, minerals, rust and grease. The lower rack, under the silverware rack is completely rusted. I have used and owned dishwashers for over 35 years and not once has one rusted like this. Poor quality for the racks! I feel it should be replaced free of charge.

Two years less three weeks after we started using the dishwasher in our new home the plastic at the top of the door where all the buttons are cracked. So far it hasnt interfered with the way its working, but were on alert that it might not be too long. Ive owned dishwashers before, one for 32 years, one for 9 years. There is no acceptable reason for there to be a crack in less than 2 years. This, coupled with a refrigerator that had a broken drawer in 13 months, I will NEVER buy another GE product again!

Let me warn anyone out there looking for appliances. We have had our 2 appliances for a little over one year, about 14 months. It is just me and my husband, very little wear and tear. Both convection oven and dishwasher not working. DO NOT BUY!

We bought this GE Dishwasher through JC Penney with a 3 yr extended warranty in Dec 2017 thank goodness. I am on my 3 round of having the mother board and the heater replaced since I got this machine. This last tech came as a 2nd opinion for my claim that this machine has not worked more than it works. All we would do is load the machine, go to turn it on and out it goes. The warranty people sent out a GE Tech who ordered a new board and fuser kit and came to put it in. Same issue, he said it was my hard wiring and I should have a electrician look at it. 200.00 later not the hard wiring. It is a pin hole in the heater coil that this last tech found. New heater now on order. My faith that this will fix the problem is waning. After this my warranty will be up and I will Never buy a GE appliance again. Not worth the money.

A week ago I placed a microwave dish in the microwave oven. The second rack was in place with the small microwave dish on it. When it started I noted flames from the rack bracket. The plastic on the rack had melted. I removed the rack and have not replaced it. This morning I place a microwavable cup in to reheat the coffee, and once again flame erupted.I am calling GE but wanted to let people know of this problem. I have had this appliance for a month. GE sent out a repairman. I overheard him tell someone that when there was cavity they considered it not repairable. Whomever he spoke with asked for pictures and from that deemed it repairable. I would not let them repair it as a fire with flames hot enough to melt the bracket and burning an opening in the inside shell is not something I want in my home. I received no satisfaction from GE as they just follow the Party line, I doubt any of them would want to take my repaired oven in their homes. I will dispose of it and purchase a new one from a different company.

I purchased a GE Spacemaker Microwave model JVM 1750SP1SS from Best Buy in October of 2011. Just a few months after having the microwave, the handle came off. I called GE and they sent a technician and fixed it but it left scratches on the stainless steel. In addition, we have had problems with the turntable. Finally on March of 2013, the keypad went out. This of course is past the one-year warranty. I called GE and they told me that they could schedule a service call for $89.95 plus parts and labor. I told them that I could buy another microwave from another company for less than that would probably cost. This microwave was made in Malaysia. I would not recommend any GE appliances that are not made in the US.

It works really well and this price point is good. It’s lasted me a few years and it is still in new condition. It has a nice modern look also. Good microwave for a great value.

Fact no. 1: On 02/25/07, I supplanted a burnt-out 12-year old Kenmore microwave oven. Regretfully, my replacement of choice is a GE JES1456WJ02 unit acquired at Home Depot in Cumberland. At that stage, my spouse was afflicted with an advanced case of Parkinsons disease, and eventually, I had her concerned caregiver reporting having found chips of paint spread on food extracted from the new oven. From that point onward, I established a close watch of the infamous appliance, after confirming that the chipping paint originated from the roof of the GE oven. But I withheld from filing a claim with GE at the time because my wifes health deterioration absorbed all my attention.Fact no. 2: But on 12/12/09, a couple of months after my beloved one passed away, I decided to take the oven to a Home Depot claim department where they immediately agreed to replace the defective unit for another one of similar characteristics. With a sigh of relief, thinking that I had taken care of the problem, my assumption was incorrect.Fact no. 3: Today, 10/28/11 in fact, I discovered chips of paint floating over a plate of soup extracted from the GE oven. I was aghast! I couldnt believe it! Still, further inspection determined that the lousy internal coat of paint is likewise peeling off from this monstrosity appliance manufactured by GE.

GE Profile Model PDW9980L00SS about 5 years old overheated and melted the bottom water sprayer into the element along with anything plastic in the dishwasher at the time. Grateful my husband was up late that night, otherwise, it would have caught on fire. It was not shutting off, had been on about 3.5 hours when it was discovered.

This microwave is nearly 20 yrs old and is still working great. We replaced the handle but other than that it has been great. I would definitely recommend the GE brand as it has been very reliable. I give this product a great rating.

My GE dishwasher has clean all my dishes. Not leaving a run or mist on no dish. I can set the time on when I want my dishes washed. The programming is out of this world! The cost is a great easy and inexpensive cost. My wife was very happy with the purchase. The buttons are not too big. Its very digital timing.

Purchased a black stainless steel microwave model JVM7195BLTS. When we opened the box we realized the handle finish was stainless steel and not black stainless steel as the rest of the unit. The website picture clearly shows a matching black stainless steel finish on the handle. Store was unaware of any problems and reordered another one. They claimed the GE rep said they had a problem with the handles on these units but didnt tell the retailers.

Purchased my first GE dishwasher 3 -4 years ago, it died, one month before the warranty ran out, they sent a repairman at no charge, acted like he did not know what he was doing, mumbled something about a part and left saying they would return with a part 2 weeks later he comes back and says that they cannot fix it and they sent me a replacement dishwasher free of charge, 13 months later and it died, So I bought a more expensive GE dishwasher thinking it would last, wrong, 15 months later and its dead, went to parts select and troubleshooted it, ordered all parts recommended to fix the issue and its still dead, these parts cost me 300, so I contacted GE to see what they had to say, no help at all except to only charge me for 50% of parts, I have to pay for house call and labor and installation, gee what a deal NOT bottom line, GE dishwashers are junk, dont buy them.

For the amt. of money I paid for this microwave, you would think it would outlast the house. I bought it 3 yrs ago. The touchpad covering started to get warped right off the bat, and the handle was always steaming hot when you used the stove top (also GE). The other day, while using the stove top, I happened to look at the microwave, and it had no power. I checked the breaker, it was fine. I happened to notice a crack on the touch pad. After further investigation, I noticed the entire touchpad is shattered. It was clearly from the heat given off from the stove top. And I wasnt even using the microwave at the time. I sent GE an email, didnt even get an auto response. I am going to call them, but we all know what they are going to say, and I am not paying $482 for the part. Was hoping there was a recall, since so many people on the net complain about the touchpad.

GE has agreed to replace and install my microwave. I am very satisfied that they understood my concern in this situation and agreed to my request.

We bought 6 new GE appliances when we purchased a new home. The reason: my husband worked for GE for 35 years and we wanted tell our friends how happy we are with them! Now, we are sorry we have to complain about the dishwasher (Model #GDWF160R1OSS). The only good thing about it is how quiet it is. We have tried many different soap products, a little soap, more soap, Rinse Aid, half clean or nearly clean dishes placed inside, only to have the glassware looking horrid, not clean and cloudy. Service man offered suggestions but none have worked. The stainless steel interior also looks horrid because of streaks. So much for energy efficiency when we have to wash all our glassware by hand to get the residue of soap off them. Another dishwasher we have had for 25 yrs. does an excellent job - so dont blame it on the phosphate removal from soap.

GE Stainless steel dishwasher rust inside. Its more show than function. Size is great. GE stated in writing that this is normal for GE stainless steel appliances as GE stainless steel is not real stainless steel. Rust is not covered by GE warranty!

I like the electronic beepings that let you know your settings, and it can be changed to your preference. I inadvertently hit the settings button and turned off the beeping and I thought the microwave was failing after only 3 months, but I discovered my error, fixed it, and all is well.

Bought a new GE microwave cafe series in May 2014. Within one month the handle which was not stainless steel started to peel and cut my wifes hand. GE sent a replacement new door for the unit that did not close. Then he had to transplant the handle from the new door to the old door. A month later the unit failed. A new replacement unit took 2 months to replace. It has worked 3-4 weeks and has also now totally failed. Our experience with GE CAFE microwave and GE service process is poor to miserable. I would not recommend this product or their service to anyone.

We upgraded our appliance package when we bought our village builder home 8 years ago. All GE Monogram appliances have rusted and now need replaced. New liners needed in oven which was so rusted we couldnt get the screws out to replace the originals. Was told by GE customer service rust to be expected when cooking. It creates steam and food particles can cause scratching!!! Maybe it should be steam proof especially a microwave. Even the door on this is rusted! Why the shelf ends in a freezer are rusted not sure on that one! Will NEVER buy this brand again and shame on them my upgraded appliances dont even make it to 10 yrs. A disgrace. My mother just replaced her 20 yr old oven. What is wrong that nowadays things dont last 5 minutes? Shame on you GE not recognizing a definite flaw in your products.

G.E. Spacemaker over the stove microwave. This is my second microwave of this type in 14 years. The first one lasted only 5 years. Im satisfied with the product albeit the price tag is too high.

Very easy to clean. Also, very reliable product. Its a built in above the stove, various levels of cooking and I love the 30 sec button. Black turntable with built in clock. Ive owned several GE products and find them very easy to work and user friendly.

I have used 4 dishwashers of various brands in my house over the past 30 years. The current one is a new GE dishwasher (Model No: GDT695SSJ0SS), which is by far the worst. The dishwasher never dry, no matter which cycle I choose. When it is done (green light on) water still flowing down everywhere inside - on the door, on dishes, at the bottom. When I called GE customer service it said I have to use rinse agent in order to get it dry. Of course that means we have to constantly buy that additional product (made by a GE subsidiary?).For those who dont remember this, our old dishwashers did not required the use of additional product and still dried dishes perfectly. GE is apparently producing products of lower quality, yet the repairman sent by GE claimed that this model is their best ever. Really? Is this company so arrogant that it pays no attention to the convenience of its customers? Since the repairman found no defect with the machine (even though it does not dry), GE refused to accept either a replacement or a return. From design to functions to price this is indeed a lousy machine. Ill never purchase another GE product again.

Our dishwasher has gotten very warm mid-cycle and now trips the breaker in the house each time we run the cycle. The problem became evident in April 2012. We have called in a GE repair person to fix it and they said it was a heating issue and not repairable. We have not used it since, but have not replaced it with a new one yet. In August, we read about the recall of a similar model number manufactured within same time frame. Our machine model is PDW7300J03WW, the recalled model is PDW7. Our machines serial # is **. Strangely, the serial number is not listed in the recall, even though symptoms are exactly the same!We have called GE Consumer Affairs at 1-800-386-1215 four times, the most recent today, 9/14/2012. Each time we call, we are left on hold for 59 minutes only to be disconnected automatically! I am sending a registered letter to GE CA with a copy of this link and intend to contact my local news if I do not receive sufficient response within the week. Does GE need to see an actual fire report from my fire department or worse in order to get their attention to replace the unit? It is disgraceful and extremely dangerous.

We had a GE dishwasher installed by the builder when the house we live in was built and it was one of the ones which were recalled as a fire hazard. We didnt really have any issues with it though, other than it was a bit noisy. With the credit offered, we decided to upgrade to a high end Profile model. The sound proofing is impressive and it was actually hard to tell the unit was on, but that is the only thing you can say that is good about the machine. As a dishwasher, it fails miserably and often items come out dirtier than when they went in. OK, weve struggled on with that for some time now but today, a nasty burnt plastic smell brought us both to the kitchen to investigate. Sure enough, the replacement for the fire hazard was the culprit. Obviously, it will need some serious repairs before it is safe to use once more. Looking through this and other sites, it seems this problem is rife and GE is reluctant to deal with the issues. Well I think that will be our last GE appliance. Thank you very much and rather than throw good money after bad, we will put the repair costs towards another machine ABGE.

GE had recalls on models 8500 and 8700 due to the motor catching fire but not my 8600 which is right in between. So besides it being the worst working dishwasher weve owned by not even cleaning well, the unit catches fire and almost burns my house down and GE wants to give me a credit toward buying another fire trap as opposed to replacing it because its 5 years old. I expect appliances to last more than 5 years and not catch on fire. No more GEs for me!

GE built-in oven with microwave on top in white color, model no. JKP90CMICC. Microwaves outside door is peeling off in chunks. This is a manufacturer defect and I have contacted GE to see if they will stand behind their products quality and replace this door of the microwave. I have heard so many negative things about GE customer service so I dont have much hope but I have to pay to replace this poorly constructed door. I will never buy another GE product and I will spread the word on how they treat their customers. I will post again when and if I hear back from them.

PVM1870SMC ($580 plus tax/Cost CDN). I bought all new GE Profile units in mid 2010 for my new house. I spent $7000, plus tax, for 4 items from a reputable company in Hannon Ontario. I bought a Fridge, Dual fuel range, Dishwasher and last the Microwave, model stated above.About 6 months back it started acting funny, but thought not too much of it as it was very intermittent. Today the Microwave will NOT seem to shut off after it beeps from cooking/warming up food and the door is open then closed. I close the door and it starts to hums. If food is in it, you can see it is still cooking. I open the door, and then close it again and it starts to Humming as soon as the door closes.The glass tray does not turn, nor does the light go on (when humming) as it does when you actually push the start button. If you do start it, everything works, that is the table turns, light goes on and it cooks/warms food etc. Then it beeps when done, you open the door to remove items, close the door, and again just starts humming.I unplug it for an hour, but as soon as you plug back in, again.. Hums until you open the door. I put a cup of water in it, and just closed the door, did not push the start button. After about 40 seconds, the water started to boil.

I purchased a full suite of GE Monogram Appliances about 5 years ago. All are fine except the microwave which was made in China. The back is rusting out, the inside is chipping at the door and moisture builds up in the door window. This progressive deterioration has taken place over the past 5 years. I paid $420 for the microwave plus $226 for the trim kit. Now, all GE wants to do is sell me a new unit and a new trim kit (will not fit old trim kit). I paid approximately $20,000 for the entire group. I bought GE because I trusted the name. Im stuck with GE if I want to match the remaining appliances. There are only two people living in this house so there is only minimal usage. To further complicate things, there is no serial number on the tag.

We are on our second GE Profile Series 60ssf dishwasher. The first one began to leak all over the floor. The store replaced it with a new one. We have had our present one about ten months. The first several months it did great and we loved it. The last two months we have noticed the dishwasher not drying our dishes. We have talked with the store several times to make sure we are doing all the right things. We are using sanitary level, power dry, Rinse Aid. We have had two technicians out and according to their computer it does not detect anything wrong. Interesting. The temperatures of the water quoted by the two were 60 degrees different. So what else is different? We received a call from supposed management of customer services saying, since the technicians could not find anything wrong, that we will have to live with whatever is going on. They will do nothing more.BUYER BEWARE! The GE brand used to be good, but not anymore. At least not in dishwashers. I definitely would not recommend this dishwasher to anyone even though it is top of the line, supposedly the best in proficiency. The unit has failed miserably, and the company had failed us miserably. We are left with a pile of junk!

Microwave is a 2001 and works just fine. There are a couple of things that could be better and that’s the exhaust and the lighting outside of microwave. Possibly could be more energy efficient but are bigger models built that way?

We have had our GE microwave for at least five years. We have moved multiple times and had the power go off but through it all, our GE microwave works just as good today as it did when we first bought.

I have purchased a GE microwave/convection oven 7 months ago. A month ago, the control panel broke down and it would not turn on. I called up customer service and a technician was sent after a week. They have diagnosed it and the motherboard needed to be replaced. The said part was ordered and I was told it would be delivered in 2-3 days and a service will be scheduled in a week. A week came and no parts showed up. I have called up customer advocate and they assured me the said part will be delivered in time for the service appointment.Unfortunately, when they came, the said parts have not been delivered and I was given the lame excuse of systems failure; the request has not gone through their system. So the technician assured me that he will put in an overnight request for the said parts and the oven could be fixed within the week. He even gave me his work and cell number for me to call if I have any inquiries. But he never picks up or even returns my calls. So another service appointment was scheduled and parts were delivered, only to find out that it was the wrong parts, supposedly for another customer and for a different microwave model.Its really frustrating when people keep on reassuring that they are going to get it done, but has done nothing but lip service. Its been over a month and my microwave is still a broken microwave. I have learned my lesson and will never again in my life time purchase a GE appliance. PS: I should have listened to the Home Depot guy that sold me this microwave.

This is what transpired on the with GE: I called GE Service because the Magnetron is defective. I had trouble talking to anyone because the Serial Number label on the unit is BLANK. Also, the unit is 9 years old. However, my owners manual reads additional nine-year limited warranty. The customer service rep said the additional warranty is 5 years and GE WILL NOT honor the GE printed manual I have. I was escalated to a supervisor and the first thing she asked for a Serial Number to schedule a service call. I said no, all I want is a new part and she responded cant do that and I cannot schedule a call without a serial number. Hello, the label is BLANK. We went back and forth, getting nowhere and I got angry (I hope can recover the call), she is an IDIOT!Well, opened up the unit and lo and behold it isnt a GE part. I got on eBay and purchased the DAEWOO part (the magnetron the microwave was built with) a lot cheaper and repaired the unit myself. Oh, she said you cant do that. Sounds like Big Brother is alive and well at GE. I dont expect a response since I have been dealt with by the most inhuman people at GE!

We have an overhead microwave that fits nicely into the spot. The power level seems to have dropped off, but this is after more than 8 years with lots of daily usage.

Purchased the Maytag MDB7749SBM stainless steel dishwasher in December 2013. The dishwasher and install totaled $700, which for that price and with Maytags past reputation, I wrongly assumed that the dishwasher would last a long time. In May 2016, slightly over 2 years, the dishwasher started having issues with the control panel. The control lock would randomly activate. I would have to reset the circuit breaker daily, leaving it off for around 10 minutes. Even with trying to go through all the steps to resolve the issue, resetting it from the circuit breaker, sequence on the control panel, the dishwasher wouldnt work. I called Maytag and after 40 minutes on hold, they finally answered. They wanted $89 for a service call and for the $143 part, plus labor. Might as well just replace it with another brand like GE, or Samsung.

Does not hold as many dishes, pots and pan as my previous dishwasher. In the bottom rack I cannot place plates and bowls side by side. Rack is too small and the gray interior is too dark. And the top rack does not hold the glasses in place, already had one break.

I cook a lot of popcorn in my microwave and it hasnt burn a bag yet. It warms food quickly. Also, it cooks bacon really good. But the best feature is the steam cleaner that saves me time. It steams for about 2-3 minutes then all I do wipe the steam off and its clean.

We have had this microwave GE JVM1631wb007 (2003) for a number of years installed above our stove. It was given to us by my husbands son so we did not have it registered with GE as owning it. However, I just sent an email to GE today asking for help as I find absolutely nothing on the internet about a scorched outside microwave door. We have had no issues with it whatsoever - until now. When we returned home from a one week vacation this past Sunday evening, we came home to a scorched OUTSIDE door on this microwave! The inside is fine. The two people who came into the house while we were gone said they did not use it but it is DEFINITELY scorched around the entire area on the outside around the screen area. I refuse to use it although my husband (who is an appliance repairman but does NOT work on microwaves) says its fine to use. Its not only hideous, it LOOKS unsafe to use. Im scared its going to catch on fire but my husband says dont worry and go ahead and use it! Im attaching a pic of it... Anyone else heard of this? Its not like we dont have the money to replace it. Im NOT going to touch the thing... You cant tell him anything. He thinks its fine. I need PROOF that this is dangerous to convince him... Please help before the house burns down!

The GE microwave that was installed in our new home (2018) stopped working in June 2020, after the nuclear reactor “blew up”. Which could have been a dangerous situation. I was told by Assurant Insurance Company that it was no longer covered by the 1 year insurance policy, and if I purchased a new policy for $241.00, they would repair it or replace it. After they discovered it was not repairable, they denied the ”replace it” part and reimbursed the money for the policy. GE agreed to sell me a new microwave at a discounted price, which I agreed to. The replacement microwave was delivered damaged, in October 2020. After many calls and waiting hours on hold, service came out and said it was “not repairable“. Again, phone calls to GE Customer Relations and reexplaining the problem, I was told they did not have a microwave in stock to replace it. However, after further searching, one was found, and would be delivered. On 10/23/20, I received a phone call from the freight company that the microwave was being delivered the following day, but they had the wrong address! it was a previous address. Where that address came from is a mystery as we never had GE appliances delivered to that address. The freight company was not authorized to change the address in the system, so another call to GE. I am still waiting for a new microwave! I can’t even begin to count the number of times I have called GE, waited on hold or call-back, waited for service, and been told I have the wrong case number. I have all new GE Profile appliances, all have had service for problems. I will NEVER buy another GE appliance. Their service department and Customer Relations department is disorganized and incompetent. GE appliance are not quality products.

This is my third microwave since 7/13. The first day I used it did not turn off, the fan and light stayed on so I returned it to H&R Greg drove to their warehouse and bought a new one. Six months later, doing the same thing, would start up by itself, very dangerous and not shut off. Had three different repairs on it three days from work!!! They came out a week ago, installed a brand new one, same model. Next day, doing same thing, started by itself. Now have to plug and unplug it for use. Now they are sending out a service call to look at it for what I told them whats wrong same as the others. The only good thing about the people at the service center have been great and the service people too. I just want this fixed. Model # jvm1750dp2WW Spacesaver.

I have a GE Profile model JT965SK4SS micro/oven combo. It came new with my new home. A couple years into it, the paint (lining) interior of the microwave start to bubble and peel and eventually started rusting. Had SEARS come out (warranty had expired) who contacted GE and they concluded it was only cosmetic that it doesnt affect the functioning of the microwave. Well, its gotten a LOT WORSE now, bubbled peeling paint all over inside, rust, exposed metal, and the paint is falling onto food. I can NOT even wipe out the interior to clean it, it makes more stuff come off/fall down. I called GE last week, was told by 2 employees that it is NOT safe to use anymore, discontinue use. I had SEARS come again (per GE). The tech said he had NEVER seen anything like it before. He called GE to tell them its not safe, exposed metal, and its dangerous. They again said, well maam, youve gotten 8 years use of it. We wont replace it, but will offer you a discount for a new one ($2,500 out of pocket for me). The person who had offered me the discount (yes, I sent pictures, showed how bad it is) also gave me a tip regarding the unit I have now with the exposed metal and the chance of arcing (spelled? like Ark) if the unit catches on fire, make sure not to open the doors, the fire should contain itself. 2 employees told me its not safe, a 3rd gave me helpful info for if/when it catches on fire... and yet, they still wont replace the unit... and do not stand behind their own products. I plan to go to our local news station, see if they can get anywhere with this, since they wont do anything. Patiently waiting and unable to afford a new unit.

Month Long Dish Washer Installation from Hell (Try #3 the best).Install Try 1 (I took off work for): Oops, I ordered the wrong hose. I am going to have to come back next week to install. I will call you and set something up. (installer). Next week Friday: Hello is this GE Installation services Umm its Friday and the guy never called or showed up this week to install my dishwasher I just purchased??!? (me). We then set up a time for the following week. How unprofessional.Install Try 2 (I took off work for): Umm still didnt bring the right hose. Can you go to Home Depot for me and buy the right one and bring it back? (installer). Ahh No!?! This is your problem not mine. (me). Well I will have to come back then. (installer). You have to be kidding me. I have to take another day off work?!? (me). Finally he gets a guy to come with the correct hose. Umm, can I borrow a screw driver and some tools from you?(installer). You have to be kidding me, sure? (me). Installer proceeds to drop the sides and fumble around banging the pieces on my NEW floor. Finally getting it installed. It doesnt look right. Dont the feet raise up and shouldnt the dishwasher be flush to the cabinets????!? and it looks crooked?? (me). Nope. (installer). I file a complaint and the guy removes my $60 install fee and sends another team out to fix it.Install Try 3 (I took off work for): 3 guys come and re-install dishwasher worse than the guy before them. From the other room you hear banging around and Oops, I broke a screw etc... This is what happens afterwards. Umm the plastic backing and sides are showing. Its pushed out farther than it was from the first guy. It definitely is NOT supposed to look like that. Plus its loose??? (me). Best we can do. Bye. (install team). This doesnt seem right....(me). Oh no, its leaking!!!!!!!!!!!! (me). So I called a plumber to come ASAP as I said before its NEW wood floor. New Plumber NOT associated with GE or Home Depot (who I probably will be getting a nice bill for calling last minute) proceeds to fix my dishwasher for the next 4 hours...Here is a small list of problems: 1) its leaking; 2) the foot vibrated off; 3) screws broke off; 4) damage to hose; 5) bottom plate installed at angle not even remotely level; 6) scratched up floor and cabinets; 7) installed too far forward and too low. This is the list. So far we still are trying to figure out where it is leaking from and if the dishwasher even will work. Thank god I actually got a Professional this time unlike GE/Home Depots teams. I then called GE Install services 1-800-432-7167 again and this is what they had to say: We already refunded you the 60 dollars. There is nothing we can do but we will file your complaint. I called again to speak with a manager and after a long conversation, he gave me $62 off my order. -- And let me tell you that is not going to cover the cost of the plumber I just hired to fix your mess. Not to mention the 3 days off work I took. Irritated I hung up. I bought a fridge, cook top, and double oven with GE along with this dishwasher. I wish I hadnt given them my business. Apparently, I am supposed to call back if the dishwasher doesnt work when my plumber is done working on it. Oh I WILL be calling back, you can bet on it. As for now I just hope he finds the leak... Moral of the story is NEVER use the install services they offer. You are better off getting your own plumber from the start.

I purchased a GE over-the-range microwave, GE Profile **, on 2/22/2005 as part of a kitchen renovation. I also purchased the GE Profile dual-fuel range, **, and the Profile ** refrigerator at the same time.I am now having to replace the over-the-range microwave as the interior enamel is chipping off in chunks rather than the discreet amounts in the beginning. The dual fuel range burst into flames and was replaced 3 years ago (the line was eventually recalled). The tracks that support the drawers in the refrigerator are breaking off slowly but surely, meaning they will not be useable shortly. I would not take a GE appliance as a gift.

This microwave (jvm1540dm5ww) works fine but the plastic door is fracturing into bits. I expect this is because of faulty plastic in China. Cheap alternatives for fast profits. The machine is out of warranty. Replacement door is almost 160$ with shipping. Planned obsolescence by corporate America. This machine works fine but is a waste because I don’t trust the replacement materials to be any more stable. I rated this a two because the actual operation is fine. Sorry GE. I will not buy your brand.

Purchased new GE dishwasher after previous model lasted over 11 years. Family eats most meals and home and typically runs washer at least 4 times per week. New model was upgrade with stainless steel interior and all the efficiency upgrades from technology advances. Ran great for first 18 months then suddenly we opened one morning and notices water standing in bottom of machine. Emptied dishes, re-ran with same result. Technician called and spent an hour diagnosing to determine water pump, control board and wash motor would all need to be replaced at a cost of nearly $600 or 75% of what we paid for the unit new less than 2 years ago. Simply unacceptable that GE would produce such an unreliable product. We will be replacing with a different brand and would tell anyone to avoid GE dishwashers.

One needs to be a contortionist to replace the under light bulbs on this microwave. It is a TERRIBLE design. Why werent the sockets placed so that the prong holes could be visible? One has to do a back-bend over the stove top and then the socket holes are still not visible. DO NOT BUY THIS MICROWAVE. DONT BUY THE STOVE EITHER. IT IS DANGEROUS. THE KNOBS TURN EASILY AND OPEN THE GAS.

We built our house and purchased a NEW close out Advantium Microwave. Due to delays we were not able to get into the house and use the appliance until literally 1 month after the WTY expired. The KEYPAD is shorted. There are a number of these complaints for this microwave - so we arranged for service. $375 dollars later - it was ALMOST working and the repair service determined that a new keyboard would be needed. 5 mos later we are kindly asked to take a refund of our repair bill and forget the whole thing - the part is not available! REALLY?! $2000 for a microwave, and you dont even support it?! Last - LAST time I put trust in GE. SCB2000FBB 03

This is the second GE microwave. In 2 years I have had that, the paint peeled off inside the microwave in sheets! I contacted GE the first time and was offered no help or explanation. I was told it was an older model, even though I bought it new. This time, I just chose to throw it away and never purchase another GE appliance again!

Bought GE range microwave JVM3160DF3BB11/16 from Lowes. Tripped the breaker. Replaced the breaker with a new. Would immediately trip the breaker as soon as you pushed the start button. Last time it tripped the breaker oven went dead. Wont even light up. Junk. Do not buy made by Haier in China with the GE name on it.

The GE dishwasher (model number GLD9312P02SS) I bought about 3 years ago is not cleaning properly because the screening that keeps the bits of food out is disintegrated, and apparently, the part to fix it would cost over $300.00. I will never buy another GE product again.

Horrible experience. I wouldnt recommend GE appliances to anyone. My husband and I ordered our items on the day of closing on our new Home. Well the items were scheduled to arrive Aug 9, 2017. Every other Appliance arrived from Samsung, but my GE dishwasher was a no show. I received a phone call hours later stating they didnt know it was on Backorder and I wont receive it until Aug 11, 2017.I spoke with supervisor Krista because I didnt understand the lack of respect far as not knowing if the 11 was a good day or even so much as an apology! Until I expressed how upset I was! 2 hours later I received a automatic message stating the items it still on Backorder and now its not coming until Aug 17th! I spoke with Home Depot who apparently has nothing to do with the vendor handling and conducting business this way and now I have to go return the product & order a new product.I dont even want GE appliances AT ALL. After calling today being put on hold 30 mins still no supervisor came to the phone. Terrible Customer service and lack of communication of the vendor. Ill be sure to highly encourage my friends and family to not support this Brand! Feeling upset and totally let down. I know this cant be how such a popular brand conducts business.

I have the GE Monogram series dishwasher. This machine has some great features. It lights up when the door is open. It is the quietest dishwasher I have ever owned. The only negative that I see is, it is slightly small on the inside.

A small black piece of plastic, which snapped into the back of the microwave handle has bent/shrunk, and popped off. My microwave is just a little over one year old. I called the GE 1-800 phone number for parts, and GE does not offer a replacement part for this, without buying a whole new replacement handle, which costs over $160.00.

This brand far above the Standards for this type of unit. This is my second purchase of this brand and I would recommend it above and beyond any other manufacturers. It’s very quiet and does a superb job of cleaning, and this dryer beats all the other. Keep producing this fabulous device, thanks.

GE Microwave was making intermittent buzzing noise 1 month after purchase. Called GE & they said they could send a tech out to check it but if they didnt find anything I would be charged a service call. I stated it would only do it once in a while so was concerned it wouldnt do it when tech was here & I would be charged so I passed on the tech. Microwave continued to make noise periodically but seemed to get less as time went on. 1 year & 10 months later it started to sound like it was arcing & shut off. Again it was periodic. Called GE. They sent a tech out & it only shut off but no arcing sound or intermittent starting & stopping. Tech stated it probably was door micro switch, but when GE called me back they said he stated it probably was circuit board. Whatever the cause it is still what I would call arcing & going off & on.GE stated They could give me a discount on a new microwave which amounted to cost of $100.00 more than I paid for it in the first place.

GE Microwave Model JES1139BLO3, Serial # VS904116B - The above model was purchased at Lowe’s in Ventura, CA about a year and a half ago. In that time, the white coating on the inside of the microwave has been deteriorating, beginning with the area under the turntable and extending out to the bottom and sides of the unit. I am concerned that our food will be contaminated by the particles that are coming off or that there will be a fire caused by the microwaves hitting on the uncoated metal. I do not plan to ever purchase another GE microwave.

In 2012 we purchased a GE microwave for around $500.00. It lasted with moderate use until 2017 at which point, it almost burned our house down due to malfunctions of internal parts. After many hours on the phone and several repair visits, GE agreed to replace it. The replacement lasted until March of 2020, at which point it started tripping our breaker. I took a half day off of work waiting on a repair technician. The technician came out and replaced a switch. Two hours after he left, the microwave stopped working. I called GE back and was given another repair appointment, again taking a half day off of work, I waited for the technician. He arrived and stated that the door of the microwave was causing it not to work and he ordered a new door.I called GE and was given another repair appointment. Again taking a half day off of work, I waited for the technician. He arrived and replaced the door. That evening, we noticed that the internal light would not shut off when we closed the microwave door. Two days later the microwave started producing a burning smell whenever we used it.I went out and purchased a $50.00 microwave from Walmart. This experience has been beyond what is reasonable for a customer to experience. I have received numerous automated emails from GEs consumer relations department from a GE consumer relations employee that is allegedly been responsible for my case. I have never actually spoken to this person even though I was advised numerous times that she would be calling me. As of this point, I plan on never purchasing another GE product nor can I in good conscience recommend to anybody that would inquire, purchasing a GE product. The customer service I received has been bad to say the least and the product even worse.

The GE microwave model CJES1290Ml01 does not get used much, maybe 15 minutes per week. I have not even used convection oven or broiler part, so we could say very gently used. Sparks and grinding noise out of the magnetron tube area started recently and there is no metal in the microwave. It arcs like there is metal. There are not enough miles on this equipment to need replacement, but it is too expensive to fix. Im not happy with Walmart GE product. Did they cheap it up?

Microwave oven, model # WES1450DN1BB, manufacture date, April 2011 - Your customer service sucks! I called there 5 times today and was told my microwave oven has been recalled, yet no one knows! You dont have it listed on the recall or anything. Your Customer Advocate doesnt know its recalled but your Service Department knows and I was told by them that it says, Do not repair, return to the place of purchase. Yet, I called my place of purchase and they know nothing of it either, but are going to work with me the best they can! It was manufactured in April of 2011 and we bought it around July 2011 (we think it was around then). There are many complaints online about the same issues as we are having - paint all bubbled and peeled off the inside top, and smell of burning wires coming from under it! If something would have happened to someone in my family or to my home, you bet your ** I would have sued the pants off of your company! Someone needs to get their ** straight with what is going on in your company or you are going to have a lot of issues! I may bring it to a higher level just because I am so pissed off that no one was informed about this issue, and something very bad could have or still can happen to someone because they are not getting the information they need! Stop and think about it. Because of your companys lack of communication, someone could die! I am very pissed off!

My life partner/bf moved into a semi flipped 10 yr old home. Every single appliance required to be replaced, everything from refrigerator, stove/oven, to dishwasher. We researched every appliance we purchased, a lot of time and effort along with reviews from various reputable reviewers, pointed us to the GE GDT DISHWASHER. Who can go wrong with three tier washing amongst jetted water bottle washers?After a 1 1/2 yrs in the top spinner completely separated from its housing. We googled the problem, GE said it was a faulty design, yet no recall. The door lock began to fail, googled the repair fix, another fault design, yet again no recall. Upper plastic door trim broke in half, solution, replace the entire console. Guess what? My solution here on out is to not buy GE products. If two years is all you get with a GE product, I am out! Done with your products that once lasted 10 to 15 years. The fact that have to research another DISHWASHER, absolutely pisses me off. I dare you GE to win me back!

Our brand new GE Profile dishwasher wasnt cleaning dishes (even after rinsing them before stacking them in the dishwasher). GE technician came several times and lectured me how I need to open hot water faucet before turning on the dishwasher, about how I should stack the dishes in the dishwasher, etc... all bogus talk. Our builder was kind enough to replace the dishwasher because he saw how frustrating it was to deal with GE service. The new GE Profile (i.e. replaced by builder) works without opening hot water faucet, or washing the dishes or stacking them in any particular manner. In summary, I wouldnt recommend GE Products because GE service is HORRIBLE and their products arent that great. I have GE Profile all over my kitchen. Within the first year, my microwave, dishwasher and built-in fridge broke down!!!

My husband and I replaced all the appliances in our new home 4 years ago with GE Profile double oven, cooktop and built in microwave. All the appliances are of poor quality and do not cook the way we are accustomed to. But the microwave has had a particularly bad history. Within one year, it completely quit working and we had to replace several fuses and a board. Over the past couple of months, the keypad continually quits working and we have to climb up on a stool, unplug the microwave to reset it. Only then will it work for us to heat something. However, the keypad does not accurately reflect the task we are trying to use. I have had many microwaves over the years and I have NEVER had to repair one before. This particular brand of microwave was produced in Malaysia in July 2008. Very, very poor quality. No resolve from GE or from Sears where we bought it. I am done with GE and with SEARS.

I had a problem with my GE Profile Dishwasher that I had for several years and I had it on factory warranty. However, the last time they came to repair, they did not have parts available to fix anymore. So, they recommended new one. I worked with Consumer dept and made arrangements to replace with one they recommended at $500+. After several efforts to get it delivered, it was and we began using. It is not a Profile like my old one and it does not have the additional washing, rinsing and drying cycles as the Profile. It is a flat out bottom line washer. No, sani clean etc.. We have used the machine about 4 times and each time we have to rewash several of the dishes and especially the silverware. This is the most disgusting piece of equipment I have ever used. My home is loaded with GE products from years ago, mostly the Profile series and I have been delighted with the products and service. This machine is a disaster. I cannot believe that GE has this on the market or maybe this is a machine they use to satisfy customers who may threaten to use someone elses. It was not free, as I say it cost over $500. The stores and onlines advertise better machines on sale for less. I have GE stock which I will sell. They are going down on Quality. Consequences: Stuck with poor machine that does not do job that I paid good money for. Really, GE, get yourself together. Product Model:GDF510PSD1SS.

RCA RMW953-White 0.9 cu. feet Microwave, 900-watts, 10-power levels, end cooking signal, glass turntable, 6-one-touch cooking menus, speed and weight defrost, cook by weight. Bubbles obscure text. I wanted a white microwave with a door handle, .9 and fairly powerful. I was glad to have found this microwave. But I dont know if the hole was there before, or my teenagers or I inadvertently put a small hole in the plastic covering over the control panel outside the microwave (NOT meant to be removed, I asked support) but now its become a larger hole as air got underneath. I cannot read the button text. I tried to cover it with scotch tape and thats not working.I searched and found out this is a common problem with GE microwaves. The buttons are very close to the bottom and therefore, countertop, so if you have a utensil or plate or something that sits near the microwave, it might nick the plastic coating. I called GE support (in India) and they said since its under warranty, I can return it. However Id have to pay shipping costs. Fortunately, I bought this at Wal-Mart (I hate to support this store but it was the only place I could find this style) and they have an excellent return policy and there is no charge for shipping. It was easy to call and request a shipping label within the generous warranty period. You might save yourself the trouble of a return or be very careful to not put a small hole in the plastic coating. Again, this is not protective coating for shipping, this is a permanent coating to protect the buttons.

Purchased this item online and received delivery on 2/13/15 from P.C Richards. In less than a month after installation of the JVM7195SFSS microwave range oven the keypad stop working making it a useless tool taking space in my kitchen. Ive made more than 4 schedules for repair service. Its now May 15 Ive yet to see a repair person. Here are some of GEs lies for the past three months: GE parts were in back order; the service person claimed I wasnt home; I didnt pick up the phone. Even an appointment on my Sabbath was botched by the service person. While homebound recovering from surgery I called PC Richard who scheduled another service on 5/14/15 between 1-5pm. Still a no show. Yet PC Richards representative stated that the service person claimed that I wasnt home. The next morning 5/15/15 11:40am a service specialist named ** at ** extension ** calls stating the repairman is sick. Im confused! On what date was my repair? How do I get rid of this product installed in my kitchen wall? How do I get my money back? How do I make PC Richards and/or GE complete the repairs without losing a work day for foolishness or forsaking my Sabbath day again?

It works well. We like this newer GE Profile with many preset buttons such as for different times and food types, and defrost. The last GE Profile MW we got had a knob that got loose right away and hard to use, like a dial-up AOL, so this upgraded model is much more convenient. I like the bigger plate size, and that the turntable can be turned off if we put a rectangular casserole dish in there.

We have a full size counter top GE microwave. It is about 3 years old and there have been no problems. Our last microwave was also a GE and it lasted about 15 years before it started to suffer from occasional electrical arcing inside, while in use. We simply stopped using it and after reviewing all models, chose to buy another GE and it has been great. We have an over the range micro at our summer home - a Frigidaire and not as good. Our research shows it will likely fail long before the GE.

Purchased my GE microwave roughly 2 years ago. Recently it started running with the door OPENED. I cannot get it to stop even when pressing the cancel button. This happened whether or not there was time remaining on the clock. I was very concerned about the microwave rays being harmful to my children. We unplugged it overnight, it worked for literally 2 minutes and then it would not even turn on. Model number HVM1540SN2SS. Pretty upset that I have to buy a new microwave already!! I was going to replace it with another GE microwave to match my other appliances, but after reading so many posts of other GE microwaves running with the door open I think I will slowly work GE appliances out of my kitchen.

We had to replace our dishwasher a few months ago and we got a GE Dishwasher and we could not be happier. This unit cleans so much better and seems to take a lot less time to do a full load. I would recommend GE to my family and friends.

Purchase a GE microwave Jes1142sp2ss on December 2014 from BrandsMart. The paint on the bottom of the microwave is peeling off exposing the metal. I have never ever heard of this happening on a microwave. I will never buy another GE product.

The GE MICROWAVE MODEL JVM6175EF1ES was manufactured in August 2015. I purchased it in November of 2015, brand new from Home Depot. It was not installed until April 2016. So less than 2 years after installation it malfunctioned. (The unit brand new only has a 1 year warranty). The parts the tech replaced have a 5 year warranty. That demonstrates to me that GE does not have a lot of faith in their appliances. Aside from that I paid $375 for the repair, thats almost the price of a new microwave. But I paid since it made more sense to have a 5 year warranty on the parts instead of a 1 year with a brand new unit. I WILL NOT be buying GE products in the future due to this product defect.

Last summer GE replaced the peeling handle on my microwave oven. I have treated the new handle with kid gloves. No abrasive cleaning products have been used and the oven burner under the handle is used infrequently at very lower temperatures. One year later its peeling AGAIN. All the burner control bezels on my GE Cafe oven have also peeled. The handles look like plastic covered with aluminium foil. Cant believe GE hasnt fixed this problem or issued a recall. I will NEVER purchase another products made by GE!

We purchased a GE Profile dishwasher, model PDW9880J00ss, in July 2005, along with GE range, refrigerator and microwave oven. We have had nothing but trouble with them. Most currently, the power board did not shut off at the end of the cycle, overheated and melted the harness also. We were alerted when the odor of burnt plastic filled our home. It was fortunate that we were home and in the next room, or our house could have burned down.The dishwasher cannot be repaired. I will contact GE to see what, if anything they will do to compensate me, but I am not optimistic. I will never buy GL products again. I thought by buying top of the line products from a well-known manufacturer, I would have a quality product. I was totally wrong. Sometimes, you dont get what you pay for.

This review is related to the Monogram 2.2 Cu. Ft. Built-In Microwave Oven model #ZEB1227SLSS. The GE site: https://appliances.monogram.com/us/specs/ZEB1227SLSS indicates in two places that the built-in trim kit is included (and one place where it is listed as additional), yet GE has confirmed that in fact, the trim kit is an optional add-on with a $325 additional cost. Calls to GEs consumer line have been disappointing. Me: Your website says its included, and is in a section with other features that are in fact included but not additional fees; GE: We have confirmed that the trim kit costs extra. We have, in fact, purchased the oven and are awaiting its installation, and I have other experience with GE Monogram appliances so I expect this to operate well. But I cannot understand their reluctance to acknowledge this error on their site. Potential buyers, please beware of this issue.

I purchased a GE dishwasher, stove and refrigerator in December 2012. All 3 appliances have broken, needed parts (which were also broken) and I still have appliances that arent working appropriately. The dishwasher door broke and it doesnt clean or dry well. The induction stove (the main burner) doesnt work and the replacement part was delivered to my house and that was delivered broken. The fan in the refrigerator broke and still remains broken. I have had nothing but headaches since the day the appliances were delivered. I would not recommend GE appliances.

Microwave Model JVM1750DP2bb defective construction- Plastic is protruding inside the Oven. Took possession of a new home in January 2014, but only occupied part time. I estimate we had the equivalent of 6 months being occupied. In January 2017 the magnetron broke down, at which time I noticed a piece of plastics protruding inside the microwave through a vent hole on the Magnetron side. I did not take the extended warranty and GE only offered to send a repair man. Since this is an over the stove model venting outside, it had to be repaired or replaced. Checked with the supplier and they estimated a minimum of $ 300 repair cost. Home Depot had model JVM6175DKBB on sale for 249.00, and with delivery, and installation, were talking $ 350.00 to $400.00 to replace. I got in touch with GE Consumer Affairs, and they did eventually agree to provide the JVM6175DKBB for $ 270.00 including installation. They will take possession of the old model, so there wont be any way for me to confirm or deny a manufacturing defect.

The GE microwave oven that was installed by the owners of my 130-something unit apartment complex caught fire in June 2014. The manufacture date is listed as December 2012. I moved into the unit in June 2013 and the microwave was brand new still and had never been used by anyone else. I myself rarely use the microwave and only use it for heating up cold food that I previously cooked on the stove top. After heating up rice using the 2 minute express option and removing the food from the microwave, I had gone to the restroom for 30 seconds only to return and find the microwave on fire. The fire ignited from the ceiling of the microwave. I had initially intended on going to the bathroom to take a shower but needed to open a new bar of soap, so I had only returned to the kitchen to throw the soap packaging in the trash. Had I not done the latter, my entire apartment could have caught fire and it would have been difficult if not impossible for me to escape from my third floor apartment. Reading all of these complaints it is really hard to believe that a government agency has not stepped in and forced GE to STOP MAKING MICROWAVES! From the complaints on this board it is clear to see that every year GE continues to make appliances that put consumers safety and lives at risk. You would think that after so many recalls that they would have perfected their product by now, but that is not the case. It almost seems as though they are just slapping new model and serial numbers on the same BAD product. The management in my building contacted GE and my microwave was replaced with another GE microwave manufactured in 2014. I did not want another GE microwave, but I only rent so I didnt have a choice. I used the microwave once so far and the fan automatically came on after 2 minutes of use. It does state inside the microwave that the fan may come on automatically, but I just dont trust this brand anymore. I have a countertop microwave that works perfectly fine that Ive owned for over 15 years that I will be using. I will unplug the GE microwave and just keep it for aesthetic purposes, since thats all its good for.

My dishwasher is a GE Profile. It is as quiet as a Bosch we had in another home we had but it must cost half as much. We have it 8 years now- no problems. Never had a service call or anything wrong with it. It owes us nothing.