We are on our 3rd washer and second dryer in 10 years. Our latest replacement (Whirlpool Duet Washer and Dryer) was purchased 3 months ago and is already broken and now we have been without a washer for a whole month. Not only do they have issues with the control panel and latch, but they smell. The dryer also had a control panel issue. Trying to get our units fixed presented even more problems and wrong parts would come in, with weeks going by without parts/service. Apologies and sympathies expressed on the phone are not enough. When you buy a matching set and only one breaks, you tend to replace the matching unit, which we regret and we went back and forth with our washer and dryer. I would never recommend a Whirlpool product after this. We finally got a replacement today and due to more poor communication on their end, they could not hook up. My new washer sits in the laundry room, and I hate it before I even get it hooked up.

Purchased the 2015 Whirlpool Cabrio. Today 5-2018, the panel went completely out. When I called the store (Lowes) they asked if I purchased the warranty. I responded no, she went on to say, “Well since you choose not to purchase the warranty youre stuck”. Even if I paid for the warranty a washer should not break down in less than 3 years. My previous washer lasted 18 years with no problems. We purchased this washer because of the larger load. It was one of the most expensive washers. It’s a piece of junk and the manufacturer will not stand by their horrible product. Please DO NOT buy! I will be filing a formal complaint.

I can not find parts for 50-gallon Whirlpool hot water heater. The left hand thread thermocouple quit functioning so I have no hot water. I have called every plumbing concern in a 50-mile radius and everyone said that it was some kind of class action suit because you can not replace the part of the thermocouple and that they only make right-hand thread couple now.

Completely disgusted and angry with Whirlpool! We own a Cabrio and just after 1.5 years of owning it the stupid washer has broke down. It wont spin or rinse or wash! Pretty sure its the bearings as I have seen several peoples complaint about this same issue! I contacted Whirlpool to only be told that they only offer 1-year warranty and after that the consumer is out of luck. They only stand behind their products for 1 year and after that its on you! They refused to help me in any way including sending someone out to look at it! Im very upset and will never buy another product of theirs! They need a class action lawsuit brought against them!

My three month old Whirlpool electric range caught on fire last night. The wiring that connects to the electrical cord to the stove shorted and melted. Thank God we were up and smelled it and quickly pulled the stove out and unplugged it. Had the fire dept out this morning and they verified that it was the stove and not house wiring. Now, I am without a stove, out of my money and waiting on the mercy of Whirlpool to take care of this situation. I do not want this stove in my house so I wont accept repair. Not sure I want another Whirlpool either. If this had happened during our sleep time, the whole house could have burned down. So upset and inconvenienced.

We bought the Whirlpool Gold Stainless Steel dishwasher around 4 years ago and the pump and motor assembly went out. We spent top dollar on this dishwasher and should of lasted a lot longer. I’m no longer going to buy anything Whirlpool makes.

I purchased a Whirlpool brand refrigerator from PC Richards two months ago. The compressor has stopped working causing my refrigerator to stop cooling and in turn all my food has gone bad. I reached out to P.C. Richards and they immediately credited me a check for the full amount of the refrigerator, with the option to get a new one delivered to me. I asked P.C.R. customer service if I would be credited for the food in my fridge and they suggested I reach out to the manufacturer. I reached out and, to my dissatisfaction Whirlpool will not credit me for the loss of the food in the refrigerator. I am completely disappointed. As I mentioned before I purchased the fridge 2 months ago. This is clearly a manufacture issue. I purchased a lemon and I am getting no support from Whirlpool customer affairs department. As a person who works for a reputable company in the purchasing department, I will see to it that we never do business with this company again. A company that doesn’t stand for anything or even compensates their customer for a faulty product should not be in business. Forgot to mention the customer affairs rep. Offered me fifty dollars for my troubles. Which I turned down. Besides the fact that fifty dollars will not cover a third of the items in my fridge, money is no longer the problem. It is the lack of customer service for purchasing one of their appliances. I am completely disappointed and will never recommend or purchase this product again.

We purchased the microwave. It looked nice and seemed sturdy. I bought a trim kit to make it look Built in. As soon as I finished installing the microwave and kit we tried to use it. My wife could not get the door to open unless she pushed the door button hard several times. I checked to see if the trim kit was causing the problem and it was not. We kept trying to get the door to open as it should but could not make it work correctly. I even used a little lubricant and it did not help. We then looked up the reviews and saw this was a prevalent problem. We then returned the unit and trim and ordered a Samsung. It will be in on the 25th of March. I placed a review on Lowes site but Whirlpool removed it saying since I took it back they removed the negative review. Since it was defective I wanted the public to see the truth on this unit.

I have used my Maytag washing machine weekly for the last 11 years... Never a problem. Just a well made, basic machine to wash clothes thoroughly. It does not have all the bells and whistles some of the newer models have, but it is a washing machine, not a video game.

I recently just purchased a new home with an upgrade provided by the builder (which I paid), kitchen appliances to Whirlpool Gold package. 2 weeks from the time the house closed escrow, I used my Whirlpool Gold Accu Bake wall oven self-clean feature. I set it for 2 1/2 hours, which is not even a full cycle of 4 hours. I noticed after 2 hours that the oven shut down. The oven exhaust was hot and the panel control as well, (almost burned my hand). No power and door locked. After a week of waiting to cool down hoping it will unlock and turn back on, it didnt. I called the builder and Whirlpool. Of course, the builder said to call Whirlpool. They registered my oven and set an appointment. The contractor (A&E) came to take a look at my oven and assumed that it was just thermal fuse. He was explaining that the oven does heat up and shut down. Probably after this repair, this will happen again. He replaced the thermal fuse and tried to turn on the oven. The house electric breaker is working, but the oven still did not turn on. So this time, he checked the control board and said that it is dead and will have to order. I am tired of having an oven for 2 weeks only and already have this issue. I did find out as well online that Whirlpool do have several complaints regarding their self-cleaning oven. I want to either just replace the whole oven or give me cash so I can replace the Whirlpool and buy another brand. I dont see the point of having a self-cleaning oven if this will heat up and shut down the unit or get a suggestion not to use the self-cleaning feature anymore so it wont break. I think this is a design issue and Whirlpool is not taking the responsibility to fix the design to start.

I bought my home in 2010 and less than a year my Whirlpool microwave started forming a crack near the handle and today August 22nd, my husband and I are looking at it thinking, this is totally coming apart! My Whirlpool refrigerator had issues also. Stopped cooling less than a year, and I am thankful I had a warranty with it. Of course it was still under the manufacturers warranty. Use to be able to depend on WHIRLPOOL. Now you feel like youre in ONE with their products!

I WILL NEVER PURCHASE ANOTHER WHIRLPOOL PRODUCT IN MY LIFETIME!!!! If I could I would rate this fridge and Whirlpool’s repair and customer service a NEGATIVE 100. My wife and myself purchased this refrigerator on 6/2/19. On 6/16/19 we noticed that it was not cooling as should, we called in to set up a repair service call only to find out that we had to wait until 6/20/19 to have a service tech come out to look at the refrigerator. When the service person came out to look at it he stated that it needed a sensor??? And that they would have to wait until the evaporator thawed out to replace the sensor. We had to reschedule another tech on the following Monday 6/24/19 to replace the part. 8 days after the refrigerator stopped cooling.Now fast forward 2 weeks and now we have the exact same issue, whatever was fixed did not correct the issue. We had to call back into Whirlpool to make a setup another service call. We have to wait 5 more days until a service tech can come out to recheck the issue. Whirlpool offered no other assistance. If I could I would return this defective unit and buy a different brand of refrigerator. I WILL NEVER PURCHASE ANOTHER WHIRLPOOL PRODUCT IN MY LIFETIME!!!! I will make sure that I let everyone I know that I would never recommend a Whirlpool product!!

We purchased a Whirlpool hot water heater approximately 4-5 years ago and have had problems with the pilot staying lit. I contacted Whirlpool and their trouble shooting included doing a draft test (I am a teacher not a plumber) and removing the closet door that houses the unit. I am very frustrated by this entire ordeal and would like if they would replace the entire unit. At this point I dont want another Whirlpool product. The plumber made a service call at 12 noon and by 3:30 we had luke warm water and by 6:00 pm the water was ice cold! I will never recommend any Whirlpool products.

Hello, Here is our story. We bought this refrigerator Whirlpool - 26.2 Cu. Ft. 4-Door French Door Refrigerator through a local reputable retailer. After 16 months we started to have problems with ice melting in the ice bin. We continued to have problems related to cooling/freezing within the refrigerator to the point where almost all the major parts were replaced. The good news is the dealer negotiated with Whirlpool to have all repair costs covered after the first visit. I asked about just getting us a new refrigerator and was told Whirlpool requires a part to be replaced 3 (THREE) TIMES before consideration.In summary, the refrigerator could not be fixed and was condemned in agreement with both Whirlpool and the Dealer. Here is the interesting news - since the refrigerator was out of warranty (12 months and now we are at 18 months), they are requiring we pay $600+ for the replacement. Buyer beware - either pay for the extended warranty or risk having to be inconvenienced by having your refrigerator unavailable for days or in our case, weeks!

I have had the Whirlpool Cabrio washer and dryer for the last two years. I HATE them. We purchased them from Lowes at a price point of around $800 each. What we expected and what we got were two different things. The washer was horrible from the beginning. It is impossible to wash a load of clothes without the UL unbalanced load indicator. It is impossible to balance a load. I have taken wet clothes out and put them back in with no luck. It takes hours for a load to finally wash. I have all but given up as I have been told it us unrepairable and too costly! Now the dryer has decided it will no longer dry clothes. It has never been a good dryer but now it takes at least 120 minutes to dry jeans. Do not buy a Whirlpool! I will never have another Whirlpool product in my home... RIP OFF.

Ice maker has stopped making ice on several occasions. Also when you try to get ice out of the door dispenser, it will continues to release ice but will not go down the chute and when you open refrigerator door it spills out all over the place. Getting ice other than from the door is no easy task. I have taken to putting a bowl under the ice dispenser. Interior of refrigerator is not user friendly for positioning items. Bought in a hurry back in 2017 and have regretted it ever since.

The American Standard 95% 2 stage variable furnace is by far my favorite furnace to install. I know exactly what to expect from this furnace and I have had zero factory issues with this model. Outside of making a few sheet metal transitions this American Standard standard 95% furnace was very easy to install as well. And like the 2 stage variable … no factory issues.

The clock-timer went out. Appliance is only 1yr. 6mo. old. I CONSIDER THIS STILL A NEW APPLIANCE. This is the 2nd Whirlpool appliance, I bought a Whirlpool washer & dryer. The washer went after 2yrs. use. I bought a Kenmore used washer and it still works. I paid cash for the stove. It was bought at a Sears outlet in Cudahy, WI for $398.58 total with the one year warranty. I really have not gotten the use of the price. I guarantee you (this company) I will NEVER buy another Whirlpool appliance again. TOO BAD YOU COULD NOT RETURN A PARTIAL OF THIS MONEY TOO ME!!!!! I have a Sears repairman coming today 8-3-13 costing me $75.00 just to walk in the door.

Cabrio Washing Machine - I purchased my washer and dryer in May of 2008. I had problems with sheets, towels and pants getting very twisted and tangled, but I just attributed that to a design flaw. My problems really began in January 2013 when loads were not level all the time. It didnt matter if it were 1 shirt or a load of towels; you had to stand by the machine and it took forever to finish a cycle.On 1/11/13, the first repair was the rods that kept the drum stable. $260.82 later, it worked again. On 2/16/13, the washer quit working. On 2/18/13, the repairman was back out. It needed a lid lock switch. It was $87.14 that time and he would be back when the part arrives ... There was still no washing machine. On 2/21/13, he returned with the lid switch and replaced it. That was $178.04 but wait, there were still other error codes so there was no working machine.I refuse to pay anymore as I now fear I will be buying a new machine after spending over $500 in less than 6 weeks, but Whirlpool did the right thing when I called and they agreed to repair the machine. They wanted a different company to come diagnose the problem (the machine gave an F50 and F51 error code to the repairman here on the 21st), so I have to wait for another repairman to come and look at the same codes flashing on the LED readout.On 3/1/13, the A&E repairman that Whirlpool sent out arrived at my house. I have been without a washer since the 16th of February. He diagnosed the problem and said that it is a $1,000 repair! I called Whirlpool and asked for a new machine, instead of throwing more money at this one. They informed me that if I didnt like their offer, they wont do anything then. I agreed to the repair.Parts started arriving at my house. On 3/13/13, another A&E repairman came out and started to fix the machine. He informed me that there was more wrong than the first guy thought, but he had the circuit boards so he would get it going. On 3/24/13, the washer quit working again and was flashing an F51 error code. This is the biggest piece of junk I have owned in my life. I have missed 5 half days of work since January and there is no end in sight. Why is Whirlpool allowed to get away with such an inferior machine?

I have purchased a Whirlpool microwave oven last year (October). It is not working properly now & not heating well. Regarding this I have registered a complaint in the service center & Customer Care but we have not received any reply for this.

Cabrio washer 2015 model - The worst washer in 40 years. Everytime I use it I ask myself why did you buy this? Sure it conserves the amount of water but I havent noticed a nickel in savings because you have to wash the same load a couple of times. Since the days of cleaning in a stream clothes have been beaten to remove soil. How in gods name was I fooled into thinking this washer would actually clean our clothes. I put a folded tablecloth in it and when I emptied it the tablecloth was still folded. IF YOU NEED A CLOTHES WASHER TO ACTUALLY CLEAN CLOTHES, DONT BUY THE KIND WITHOUT AN AGITATOR. (serial # C52242825)

I had my Whirlpool electric stove for about fifteen years, I have had a couple minor problems with it. The oven temperature sensor went out, I bought a new one online and replaced it. The stove top eyes get warped from uses. Really no big deal. Ive had good luck with it over the years. Its the standard 30 inch white. I paid over $400. It will probably last me another 15 years, I dont see why it wouldnt. But then I know how to fix appliances. I think the only reason why anyone would replace a stove is because of the color or it caught fire or wont come clean. The mechanical isnt a problem because you can rebuild them so easy.

Dont buy this washing machine. All of my clothes are dingy and gray. I paid $1,751.96 for this set. What a big waste of money. Sometimes the clothes come out with dry spots and then some come out with lint like they have gone through the dryer and yet they are coming out of the wash. Often they are in a very tight large ball in the center of the machine. I distribute evenly around the machine and I dont overload. The brilliant engineer that decided the machine did not need a soak cycle is a person that has never washed clothes. Wish I would have taken pictures of some of the soil still left on my clothes.

Like everyone else here, I had to call a repairman to have a look at my washing machine after 4 years of limited use (only my husband and I). As soon as the repairman looked at it, he told me theyve had so many calls for this particular washer. He ordered a new part for it, but it did not fix the problem. Thankfully we purchased extended warranty and we were credited the full amount + tax. Today I picked up a brand new Maytag washer. Cant wait to try it. Thanks Leons for the great service.

I have purchased 2 Ikea/Whirlpool ovens in 2011 from Ikea in Canada. I have used the self clean feature on both ovens and both ovens quit completely and the doors stayed locked. This problem is discussed hundreds of times on the internet for Whirlpool, Ikea and Kitchen Aid ovens. Since they are all made by Whirlpool they are all very similar or exactly the same in some cases, as is the problem. I have discussed this with Ikea and they have said they didnt know about the problem but would help to get it fixed to my satisfaction. I have had Whirlpool authorized service repair both ovens but after trying the self clean feature again, same problem.During one of my conversations with an Ikea representative on the phone, she contacted Whirlpool and was told that if the oven was repaired 3 times and deemed by the service technician as unrepairable, Whirlpool would do a buyback. In other words according to Ikea, Whirlpool would take the oven and pay me what I paid for the oven. Well after contacting the authorized service dept (not Whirlpool itself) for the third time, they did some investigation with Whirlpool about the problem. To his and my amazement, Whirlpool has come up with a fix as of October 2013. The technician ordered the new kit and installed it in both ovens. I have since tried the self clean in one oven and this time it worked. For the information of others, Whirlpool has the kit and in it is an instruction sheet with pictures as to how to replace and install all the parts in the kit.I watched the installation, quite a process. From the instruction sheet there is a number on it. Here is the number - w10625529 rev. A 10/13. This is an instruction sheet for Ikea TOD (thermal overload device) service kit. I have looked at many of the service parts diagrams on the internet for many different current models of Ikea, Whirlpool and Kitchen Aid ovens and in most cases almost all the inside parts are the same or very very similar which leads me to the conclusion that this service kit may work in most of these ovens to correct the same problem, but I suggest checking with the appropriate service people before taking my word for it. My observation is that the kit moves the TOD off the top of the metal plate of the oven and onto a new bracket which the tech thought it was to get it further away from heat (this Im not sure of since Im not an expert). He also suggested that this kit may also be designed to allow more air flow around the oven.My only concern after having the self clean feature finally work is the heat produced inside the kitchen cabinet in which the oven is installed. Approximately an hour and a half after turning the self clean on, I felt the side of the cabinet between it and the fridge (open space), and at one area of the wood cabinet I could not hold my hand on the cabinet as it was too very hot. I will be checking the inside of the cabinet for signs of excess heat and if I see any evidence, I will again call the service people. Since the elements were not on when I checked this, I assume the self clean had finished the heat cycle and was in the process of cooling down. When I test the other oven, I will make sure the elements are still on as I can see them thru the glass door. When I checked the temperature of the outside wood cabinet using a laser thermometer, the outside wood registered 64 degrees C or 142 F approximately. Not sure what the inside temperature was as the oven was still in place. Hopefully I will not get a higher reading when the self clean is at its maximum temperature in the cleaning cycle. Will the oven create any problems in the future for the cabinet, I hope not but time will tell. For clarification, the cabinets were built by a kitchen cabinet company using the instruction sheet that came with the ovens. I hope some of this will be of help to some of the hundreds of people who have posted this very same problem on the internet. When you have paid for an appliance you wanted because of the features it came with, it should provide you with what you paid for and not constantly break down. Im lucky as they came with a 5-year warranty so it hasnt cost me anything yet and hopefully wont in the future. Good luck to all in getting this resolved for all of you.

I purchased a Whirlpool Ref side by side 11-2013. I have had nothing but trouble. First the Ice maker leaked, was fixed. The door to the ref has had serviced 5 times. The tech after many times trying to fix hinge on door twice was told to order new door. This took 6-8 week to get. Came today 5-27-15 too but new door on. It is still not right, has big gap in the middle - still not level as should be. I have called Customer Service again today with no help. All they want you to do is spend more money on a contract. I THOUGHT WHIRLPOOL WAS SUPPOSED TO BE A GOOD PRODUCT......NOTTA....WILL NEVER BUY THIS PRODUCT AGAIN. SO IF YOU EVER BUY WHIRLPOOL PRODUCT BE SURE TO GET EXTENDED WARRANTY. YOU MIGHT NEED IT..........STILL NOT SATISFIED AND NO HELP IN SIGHT.

Since buying a Whirlpool Cabrio washer about 3 years ago have had several breakdowns. Within 6 months the computer completely failed. Since then it failed again. About every six months it costs me around $125 to get it running. The thing is a piece of junk. If the load is slightly unbalanced it just shuts down during the spin cycle. The old Maytag we had ran for over 25 years with the belt replaced once. No other problems. Will not buy another Whirlpool again.

We have had a Whirlpool dishwasher for about 2.5 years and have been happy with how it cleans dishes. About a year ago we replaced our counter top and in the process had to adjust the bend in the mountain brackets that attach the dishwasher to the underside of the counter. This requires flexing the thin piece of aluminum at the perforated line. In the process, one of the brackets snapped. The other was barely still intact and broke several months later. I tried jerry-rigging them, but eventually decided to replace them and called Whirlpool customer service to ask for replacement parts.Unfortunately, Whirlpool wanted to charge me $10.50 apiece and another $9.00 for shipping and handling. These parts could not cost more than a few cents apiece. I was shocked that they would charge me $30.00 to replace these flawed parts. Never have I had such and experience with any customer service department. The three people I spoke with were all rude and unapologetic about my situation. Two blamed it on the install...Ive installed plenty of dishwashers and never had any problems in the past. Even if it was a failure on my behalf, the simple replacement of the parts for a reasonable charge would have been fine by me. I told them Id be happy to pay a few dollars and to pay the full shipping fee (which was also high, in my opinion), but they refused to meet me halfway. I can only think that this is part of their business plan...make dishwashers with sub-par parts, and then over charge for the replacement parts when they fail. Well, I re-upped my jerry-rigging efforts and have improved the engineering of the faulty part. Save my $30. But Whirlpool will never again get my business and Ill be sure to steer clients and friends away from this brand as well.

Purchased this French door fridge with the freezer on the bottom in September 2017. Started having problems shortly after with the freezer not auto defrosting/ice damming on the evaporator unit in the freezer unit, which caused the fridge to warm up and food to spoil. Service came out several times and ultimately replaced the Jazz board 3 times, 2 harnesses in freezer, 1 Heater and the evaporator fan motor, with the same problem happening after a few weeks. Requested a replacement after the 3rd visit, but Whirlpool refused to back up their product. Sent service a few more times to no avail. Demanded a replacement once again. They sent a new service company out 15 months after our original purchase and they FINALLY deemed it non-repairable and are FINALLY going to replace it (turned out to be a broken wire inside the walls of the fridge, likely was like that upon delivery). So now we will have been put out for a total of 16 months for a fridge that cost >$1000. If Im spending that on an appliance I expect it to work properly or else be fixed/replaced in a TIMELY fashion. And the best part: they refuse to compensate us for any of the food that was lost due to a faulty product and very poor customer service! That was a lot of money lost because of their incompetence. If they had just replaced the broken appliance in the first place I would have been satisfied. But since they refused to do anything beneficial to remedy the situation, I will NEVER buy another Whirlpool appliance again. And add in the inconvenience of scheduling a time to be home for multiple visits to greet the repairman. Oh yeah, plus our time wasted defrosting our frost-free fridge with a blow dryer to buy us time until it got repaired. Buyer beware!

I purchased a new Whirlpool 3.6-cu ft Top-Load Washer (White-On-White) Model #: WTW4800BQ from Lowes on 11/1/14, which was only 3 ½ years ago. The washer began making noise during the spin cycle so we called for service. The technician claimed that the bearing pack needed to be replaced and the repair would cost $400. This amount is $20 higher than the amount I paid to purchase the washer. Because the warranty is only one year, I contacted Whirlpool today and spoke with a representative. The representative said they could repair it under the warranty. When I asked how to proceed, she then asked me if I had an extended warranty. When I replied that if I had an extended warranty, I would be using it. She declined any assistance. I now have to purchase a new washer after only 3 and ½ years. I own 10 rentals. I promise that none of them will ever include a Whirpool product again.

Cabrio is our washer and dryer. Dryer had no issues in the last 7 years. Washer constantly throw UL or unbalanced error and stops. Rearranging clothes only works for another few minutes. First time under warranty, tech came and fixed it. Second time without warranty, I cleared some loose socks between the tub. Third time same problem. YouTube suggested to change the springs on four corners that hold the tub. $25 and problem fixed. Basically, if you are not an informed consumer you are screwed for $$ silly stuff.

My range is 2 years old. I would never recommend this range. The AquaLift clean is worthless. Can not get the grease splatters off. If I could afford a new one I would get rid of this range. The AquaLift clean feature is only good for small messes on the bottom.

I had my entire kitchen re-modeled in May of 2013 and purchase all new Whirlpool appliances. I work for Standard Pacific Homes and purchase the identical appliances we provide in our homes. I am so disappointed in the refrigerator. Two months ago it stopped making ice and I was told to replace the filter and it would be OK. I did that and still no ice. I bought ice trays. A couple of days ago, I came home to find water on my kitchen floor coming from under the refrigerator. I called Whirlpool again and no real help.... Told me to call Lowes. I called Lowes and they gave me 3 more numbers to call for service. None of those service providers had any available appointments and told me to call Whirlpool. Meanwhile my refrigerator is standing in the middle of my kitchen so I can keep the water mopped up. The refrigerator was so difficult to move. Getting the feet moved up so the wheels could touch the floor took an hour and I ended up with bruised hands. My lesson in this is to buy a better brand next time and go top of the line. I sell these to our buyers at Standard Pacific Homes everyday..... Wish I could believe in the product.

Bought Cabrio 3 years ago, started getting ul code and f1 code. We leveled machine, but cycle kept getting stuck mid-cycle. Called repair guy, they say it is going to cost between 6 to 800.00 to fix???? Really. Its three bloody years old. Very disappointed. Do I now get it fixed or break down and buy another washer. I would not buy Whirlpool again. Very pissed.UPDATED ON 02/05/2015: We called an appliance repair company and initially paid $440.00. After installing a motherboard computer system, it still did not work. We were then told that the other part would be another $120.00. We were already soaked for $440.00 so we decided to pay. After that was repaired the washing machine was still stalling mid cycle. We were then told that it has something to do with the wiring and it would cost another $120.00-$140.00. Needless to say, we declined. Complained to whirlpool that machine was three years old. We are pissed and $570.00 out of pocket. Just bought a lg front loader and paid for a 5 year warranty!!

Whirlpool oven WOD93ECOA501 - This oven will most likely lock up if you use the clean cycle. I wish there was a class action suit in California. This happened first time I used the oven. Very expensive to fix, and though it was 9 months after a kitchen remodel, it was not under warranty because we bought it early and it sat in garage, and Whirlpool could only use purchase date. This is not new technology. Upper and lower oven both locked. Wish I had bought a Blue Star oven, as my Blue Star cook top is fantastic and a pleasure to use. HAS ANYONE GONE TO SMALL CLAIMS COURT?

A reliable machine at a very really good price. A nonsense machine that does a very good job at cleaning our clothes. Has a good number of features that make washing different materials easy and safe for their fabric types.

5 years and 11 months ago I bought a 50 gallon gas, Whirlpool hot water heater with a 6-year warranty from Lowes. The 2007 water heaters were on sale, so I paid $329 for it. Within 6 months, I replaced the gas valve, and a few months after that, the thermo-couple went out and I replace that. Each time I called Whirlpool and got return authorization numbers for the parts, I still ended up paying for the parts plus labor. A year after that, the igniter went out and I had that replaced. Last year (the day before Thanksgiving), the thermo-couple went out again and I had to have that replaced - and it cost me for the part plus the labor - even though I had a return authorization number. I also replaced the water line connections/hoses to the water heater at that time. The customer service rep for Whirlpool told me at that time if I had another problem with the water heater, they would replace it for free - and the warranty was good until Dec 31, 2013 (this year). NOTE: Every plumber that has come out to fix the water heater and replace the parts stated that they see a myriad of problems with Whirlpool water heaters. They said the parts like the thermo-couples, igniters, gas valves, etc are poorly built and they replace them all the time. On Christmas Eve 2013 (two days ago), the water heater started leaking from the top by the valves - and so much pressure had built up in the heater the new water hose connections burst, spewing water all over the heater closet. I called Whirlpool the day after Christmas (today). At first, they told me they would not replace the heater as it was not in warranty and then I told them what I was told by the service rep last year. She finally agreed that my heater is indeed under warranty and gave me a replacement authorization number but she told me my warranty did not cover labor. I called Lowes. At first, they told me I would have to remove the old hot water heater myself and bring it back to the store in order to get my replacement. I am a 59 year old woman and I take care of my brother, a disable veteran. Although I am in good shape and healthy, I dont have anyone to help me get the gas and water disconnected and help me lift it into my Suburban. The man at Lowes agreed to bring out the the replacement heater and pick up the old one at no charge, but I will still have to pay $299 plus the cost of new hoses to have it installed. By the time the replacement one is installed, I will have paid a little over $1200 for a $329 water heater. I could have installed a tankless one for that, but I cannot see spending that kind of money right after Christmas. If I have one issue with this replacement, I will install a tankless water heater - and it will not be made by Whirlpool or any of its affiliates. My recommendation would be to steer clear of Whirlpool and their products.

Offers a long-lasting, high-quality finish that resists scratches and rust. Provides smooth, efficient operation and reliable combustion efficiency. The ECM motor provides computer-programmed airflow for greater efficiency, humidity control, reduced noise levels and increased comfort. 2-Stage Gas Valve System Allows the furnace to operate at a lower output setting to more efficiently control your home’s comfort in relation to the temperature outside. Reduces gas usage by 30% on most days. Durable, Baked Polyester Pre-Painted Steel Cabinet Offers a long-lasting, high-quality finish that resists scratches and rust. Aluminized Steel In-Shot Burners Provides smooth, efficient operation and reliable combustion efficiency.

This is my third Whirlpool refrigerator. The first two lasted about 20 years each, and although not fancy, they were always serviceable. This one is different.Because of my kitchen cabinets, the only refrigerator with as much storage capacity (cu ft) as my old one was what seemed to be an almost identical Whirlpool, with the only exception being a slight difference in the ice maker. But this one is a disaster. The water/ice dispenser has been changed to one with one space only for your container. The water that comes out is warm, because the routing of the tube has been changed and it no longer goes through the chilled refrigerator space; the ice pours out so hard that usually half of it lands on the floor. In order to operate the dispenser using anything with less than a 4 diameter, you need two hands: One to depress the lever behind your glass and one to hold the glass farther away from the refrigerator. Failure to do that results in a wet mess. After dispensing crushed ice, it continues to send small pieces flying long after I change the switch to cubes. But that is the least inconvenience. In an apparent engineering change to meet energy efficiency, the new refrigerator recycles air from the freezer to the refrigerator compartment. That and other changes in the frost-free engineering have resulted in:Uneven cooling in the refrigerator. In fact, it froze $1800 worth of insulin pens. I was advised by the Whirlpool representative that I shouldnt have put them on the shelf where the vent from the freezer spews out freezing air. Spoiled food in the freezer. Everything in the freezer develops a thick coating of ice crystals within a short time. This dries out the meat, shrinks the popsicles, and destroys the quality of fish and fowl. At this moment, I have two pork chops that defrosted in a plastic container on my kitchen counter. I bought them fresh, and now the 10-12 oz. of pork is swimming in over 1/2 c. of water.Interior fittings are poorly made and shelves and drawers do not work easily. The allegedly stainless exterior is difficult to clean, and many reviewers have remarked that they find rust within a few months. I could go on. There is more poor engineering, and an array of noises filling the kitchen, but you get the picture. I wish I could trash this refrigerator and buy a good one, but that isnt feasible both because of budgetary and space constraints. The last service person who came out sighed and told me that the refrigerator was cold, and that meant that the unit was operating okay! I HATE this refrigerator and struggling with it from day to day. My hope is that no one will buy a Whirlpool ever again. I certainly wont.Updated on 12/05/2017: Whirlpool, faced with my wrath over a refrigerator set on LOW that froze $1800 worth of insulin, provided a replacement (25 Cu Ft side-by-side refrigerator). I have owned two previous Whirlpool refrigerators -- for 20 years each -- as well as other Whirlpool major appliances. I WILL NEVER BUY ANOTHER WHIRLPOOL APPLIANCE. The replacement is deficient in every design and functional aspect I can think of. Temperature is uneven in both freezer and refrigerator. Food in the freezer is coated with snow within a week and dried out and spoiled within a month. Ice comes out with such force that it ricochets out of the glass and around the floor. Water from the dispenser is warm. Leafy vegetables spoil within 2 days. Whirlpool sent technicians who informed me that the unit was working properly because it was cold. PIECE OF JUNK! DONT BUY ANYTHING MADE BY WHIRLPOOL!

Whirlpool Refrigerator Freezer WRF560SEYB01. Purchased the Whirlpool Refrigerator Freezer in 2012 at Sears. Ran okay for 2 years. Bottom freezer door came off the track. Called Sears. Sent out repairman for $200 to replace the door. He did not check the ice buildup on back of freezer. Next problem, severe ice buildup, loud noise. Used hair dryer to melt ice and took the blower fan out of freezer. Solid ice on all the blowing fans and found a chunk of solid ice. Freezer no longer made the noise until the ice built up again. Now, it continues to build up and we have to use the hair dryer every two weeks. A refrigerator should last at least 10 years. This model doesnt even warrant a rating of any kind.

My husband AND I purchased our Whirlpool Cabrio washer and dryer from Lowes in 2011 (Model # WTW7800XW2). About 10 months after I purchased this I noticed a hairline crack on the right side of the frame that holds the glass top near the hinge. I didnt think to much of this. I figured it may have been screwed to tight when manufactured. A few days ago I noticed the lid wasnt sitting flat and saw the crack had gotten much worse. The Cabrio lid is made with a heavy piece of glass inside a plastic frame allowing you to see through the top. Its pretty obvious that the plastic frame is not durable enough to hold the heavy piece of glass.I called Lowes and they told me that because I didnt purchase their extended warranty that I should contact Whirlpool. I called Whirlpool and was told it was a cosmetic defect because the washer still works. They also told me my washer is outside of its warranty so they would schedule someone to fix it but I was 100% responsible for the repair costs (which I found out will be $400). Out of curiosity I googled this issue online and found numerous people complaining about this exact same issue. When I told this to the customer service agent at Whirlpool, she said there werent enough people to recall the product. Why should I spend $400 when it was a design flaw that caused this problem? I found out the year after my washer was made, the lid was redesigned with a much sturdier frame, Coincidence? I think not!I havent had any problems thus far with the dryer but with the experience Ive had with this washer will make me never by another Whirlpool product again. I cant believe they wont stand by their product! Obviously they know this has been a major complaint on this model from 2011 because it was changed the following year. I have purchased many Whirlpool appliances over the years but dealing with this issues has been frustrating. Im so disappointed in Whirlpool and their lack of integrity!

I had owned another Whirlpool Washer before, which died. I purchased this one. It was noisy and unreliable. Whereas the previous one lasted for 10 years, this one stopped working in less than 6. I went out and replaced it with a GE instead.

ED5PHEXNK00 Stainless Steel side by side Refrigerator bought in 2004, look out!The refrigerator caught fire today and there was smoke everywhere. Had I not been home, damage would have been out of control. I traced the smoke to the bottom of the refrigerator. I pulled the unit out from the wall and unplugged the power to the unit. My unit is out of warranty and past the extended Lowes warranty. The repair diagnosis is $100 to start.Whirlpool has recalled its other brands (Maytag, etc.) for this same problem but not its Whirlpool brand. Our problem is the same problem with hundreds of other people: Whirlpool fridges burning, smoking, and being a life threatening hazard to families all over America because of the faulty relay to compressor. Whirlpool better recall this model. They need to fix this or they will have much bigger issues to deal with (corporate manslaughter from a known issue and no action or protection for its consumers). The refrigerator is a result of Whirlpool’s negligence; thus, it’s potentially deadly.

Today I had the unfortunate experience to have to deal with Whirlpool customer service and claims. I WILL NEVER BUY ANOTHER WHIRLPOOL PRODUCT again! My refrigerator, that was purchased in 2013, has a door misalignment problem. It is a known problem with Whirlpool (service pointer W107317828). My refrigerator serial number and model number are affected. Because I am outside the one year warranty, Whirlpool refuses to provide service that is required to fix this known issue with my model/serial number. After having to talk to four supervisors the only resolution that was given was that they would cover the cost of the 7/16 hex nut ($4.33). Dont get me wrong I do appreciate the offer.The two supervisors that were below her assured me that no one can do anything to assist me further. The attitude of the second and third supervisor was pathetic. After over a hour on the phone I was so disappointed that I could not take it further. The cost that we are talking about that I am asking them to pay is $154.28. I am very disappointed. They say they stand by their product. To me standing by your product means that you will fix or replace any known issue. $154.28. I hope it is worth it to you Whirlpool. You lost a long time customer.

Whirlpool Cabrio washing machine is less than five years old. First repair was replacement of control panel (under warranty). Second, third and fourth attempts to fix the out-of-balance problem which continually caused the machine to shut down altogether (even a small load) left my repairman totally frustrated after replacing most of the parts, finally telling me it just cant be fixed! What? I paid over $1,000 for this machine in Oct. 2007 and expected it to last many, many years. My mother-in-law has a washing machine she bought used in 1979 and it is still working beautifully. Ive read the 14 pages of complaints on the Consumer Affairs website and agree with Diana in Kissimmee, Fl - I am sick to my stomach not only for Whirlpool not recalling the Cabrio, but for Lowes and Sears and any other supposedly family-friendly business for continuing to sell it! Someone please contact me if you know of a class action suit being filed.

I have hated this Cabrio washer and dryer set since the day they were delivered brand new by Best Buy a couple of years ago. The washer does not clean well, often does not spin dry, and leaves some clothes dry after a full wash cycle!!! I have to wash small loads on the deep water cycle to even have a chance at cleaning the clothes. The clothes are so dreadfully compacted and tangled that it takes great effort to birth them out of the washer, unfurl them, shake them, and put them into the next torture machine- the dryer. It is as if Whirlpool intended to build a machine to twist clothing so tight that it requires a bodybuilder to untangle the clothing. Then the items are so incredibly crumpled that ironing has found its way back into my already busy life. Ironing is a massive challenge to the degree of wrinkles in the clothing. The slanted tops are icing on the cake. Cant even pull the clothes out of the dryer to the top of it because they slide right off. Cool.

I bought a Whirlpool washer and dryer a little over a year now and the washer is not filling enough water for the cycle to wash properly. I have to fill the washer myself and this only started a couple of months ago. This happens even when I have a heavy supply of water.

I purchased a brand new washing machine and had service come to repair the machine approximately five times within the first year. Every time the machine was repaired, it was for different reasons. I contacted the main office and spoke to a woman named Sherry who is a supervisor and she was very nasty. This is a brand new machine and I feel that it should be replaced with a new one. Sherry said that there was nothing she can do for me. Is there a lemon law for appliances? The machine is used for my son and me only. I have all appliances in my house by General Electric and this is my first and last experience with Whirlpool.

We bought all new Whirlpool kitchen appliances in February of 2017. The French Door Refridgerator MRF993FIFM we purchased was a large side by side with a water/ice dispenser and freezer on the bottom. The concept of it is great, as it is very roomy. The problem is with the product quality and usability. We are a family of four with the youngest being twelve. We do not have to worry about rough little hands anymore. That being said there is a crack in the back of the plastic casing of one shelf, a crack in the freezer door, the seal doesnt connect on the dispenser side door, the slide out shelf in the freezer doesnt stay on its rollers and the main ice maker stopped working (which never worked properly either).Also, and this is what bothers me the most, the glass on one of the shelves is sealed down so it cannot be cleaned under. But there is a small slit going all the way around that separates it from the plastic. Food is still seeping underneath and creating mold with no way to clean underneath! This was not an inexpensive refrigerator and we were not prepared to have these kinds of problems after a year. We are very unhappy with the quality of this product.

I had an upscale Frigidaire suite of kitchen appliances and I loved them. A few years later I moved and needed a new set. I thought Whirlpool was about the same and I bought a Whirlpool set. The stove wont boil water or even fry an egg. It heats up and cuts off continuously. I called a service rep out and he called the engineer who told him it is designed like that and I need to use hot water on the stove to boil it. I was shocked at his ignorance and insulted by his stupidity. Ive been cooking for 60+ years and everyone who cooks knows you use cold water to boil water. But really, the stove does not cook anything. When frying eggs the burners cut off every few seconds to the point you cannot cook anything with it and the engineer said thats the way they designed it. DONT BUY WHIRLPOOL. THEY WONT EVEN BOIL WATER. HORRIBLE STOVE AND ONCE YOU HAVE IT YOU ARE STUCK WITH IT.

I lodged a complaint of Microwave problem on 05/11/2011, and up to this date (18/11/2011), I am still waiting for the problem to be solved. I have a 1 year old baby. We cook food for him in it. Due to the microwave not working, he is suffering.

I join the many who have posted about the Whirlpool Cabrio Washer cracked lid issue. Our Whirlpool Cabrio WTW7800XW2 glass-lid washer suffered the same (inevitable) fate – cracked plastic on the lid at the hinge stress points, after the washer was beyond warranty. Same story - runaround/no help from Whirlpool. Finally bit the bullet and shelled out the $200 for a new lid. HOWEVER, I didnt want to just replace it and have the same issue down the road. I removed the spring-loaded units that support the hinges, hoping to just remove the springs to release the pressure. I found that the springs are integral to holding all the components together in this unit. These are extremely heavy-duty extension springs, so I took them to my hardware store (TrueValue) and found springs the exact same length, but with a smaller wire diameter and thus requiring less force to extend. I replaced the original springs with these (Century Spring Corp. - #C-143 - 9/16”x3”x.054”). The lid operates perfectly, and now there is very little resistance at the hinge stress point. The only difference is there is no longer a “damping” effect when lowering the lid - it must be lowered manually rather than being allowed to fall on its own. That’s a small correction in habit, but will ensure that the replacement lid lasts for the life of the washer.

Soon as warranty expired issues with product. This should not happen. Made in America, washer making too much noise. Products cost more but poor quality. What is this company going to produce? This is the world we live in.

I had started the dishwasher and had gone to bed last night. I came downstairs ten minutes later to get a bottle of water. There was smoke throughout my downstairs levels. Our Whirlpool Gold Dishwashers control had dark, noxious smoke emitting from it. I tried to turn it off but it was too hot to touch. I went to the breaker box and shut it off there, turned on fans, and went back to bed. This morning, it turned the electricity back on. It started smoking again. I tried to cancel the cycle but it wouldnt cancel. I opened the door to stop the cycle and it continued spraying water and still wouldnt shut down. I had to shut it off at the breaker again. Next problem is my refrigerator, washer and dryer are all on the same breaker. UGH! This is the second Whirlpool I have had. The first one had a rusted tub that leaked into our basement. The repair guy said he had never seen that before...sure...why would you put something in a dishwasher that would rust out on you? Whirlpool, NEVER AGAIN. I WILL PASS THIS INFO ON TO EACH AND EVERY PERSON I EVER KNOW. COUNT ON IT.

My Whirlpool Cabrio washer (WTW6600SG2) is a money pit! After reading all of the nightmare stories concerning this washer one would think Whirlpool would offer a recall and try to correct their wrong doing. Do not buy a Whirlpool Cabrio. It was the worst decision I have ever made! Whirlpool does not stand behind their products. I cant believe they can get away with treating their customers so unfairly, taking their hard earned money for crap like this, then not offering to help after so many have had issues. The Cabrio is loud, doesnt get clothes clean, and is always flashing UL for uneven load (when it works at all). My local repairman has made many trips to fix my problem Cabrio. This time he is at a loss. Ill be buying a new washer and it will not be made by Whirlpool! Please, if you are reading this be forewarned!! You will regret your purchase if you buy a Whirlpool Cabrio.

I purchased a Whirlpool fridge brand new. Not even a freaking yr old it went out!!!! Repairman came out and said it had leaked crap all over really. He said it would be too much to repair. Better off on purchasing a new one.

HORRIBLE! I purchased a Convection Oven Microwave in Oct. 2010 and 3 months later, the microwave stopped heating! I called customer service and they replaced the magnetron and two other parts. Two months later, the appliance broke again with the same problem. They serviced it again. Today, it was broken again and the service technician stated that its the magnetron again. I called to get it replaced and they said Whirlpool doesnt replace appliances, they just keep servicing it. **! How can they get away with this!

I purchased this washer model WTW4950XW0 new. Within 6 months, it stopped spinning and was repaired under warranty. The spin actuator was defective. Great. A few months later, it stopped spinning, repaired under warranty and the spin actuator was bad. A few months later it stopped spinning, repaired under warranty, and the actuator was bad. Great. Another few months it stopped spinning again. This time, Whirlpool sent someone to repair it, another bad spin actuator. This time we had to pay for the part. So now that we are completely on our own, it stopped spinning yet again. Let me guess. The spin actuator is bad!!! Incredible. What a piece of crap. This washer was never used heavily.

Updated on 12/28/2020: I purchased a 28 cu. ft. side by side Whirlpool refrigerator less than 3 years ago (Feb. 18). The icemaker dispenser paddle quit working nearly a year ago and there are no replacement parts supported. Today the ice maker quit making ice. This is crap for a major appliance that youd expect to go twenty years or so. Very dissatisfied. Dont waste your money on this stuff.Original Review: I purchased a Whirlpool side by side refrigerator about 2-1/2 years ago, paid $1,800+ for it. Now two months ago the ice maker dispenser through the door quit working. I replaced the auger motor and that didnt help. Now the parts department says the actuator panels are no longer available. This is planned obsolescence to the Nth degree. No support for a major appliance less than 3 years old. Whirlpool SUCKS!!!

Whirlpool Gold Series - I bought this dishwasher less than 2.5 years ago. The thing already broke. The motor needs to be replaced at a cost of about $250. The thing never did a good job anyway and often had to run it more than once to get dishes clean. I paid about $650 for the machine so I guess its just a throw-away appliance. Whirlpool makes complete junk. I will buy a different brand that is known to have long-lasting dishwashers. I guess you get what you pay for.

We purchased this model in July of 2019 and have had nothing but problems with it since. The design is really bad - if you set the temperature on the ideal setting, everything on the top shelf freezes solid. If you reduce the setting to the one below ideal, your freezer doesnt get cold enough to keep ice cream hard. The ice cubes are a little more than half the size of our last Whirlpool refrigerator and the unit is noisy. Weve had Whirlpool out to work on it 4 or 5 times in the first 6 months and twice weve had to throw away food due to the unit not cycling on and off properly. One of the technicians told us he spends a lot of time working on this particular model - evidently, it has a lot of issues. We are now using our old garage refrigerator while we try to get Lowes to give us a refund on this piece of junk.

Bought a Whirlpool fridge in a package from Home Depot three years ago. The fridge has already stopped working. It started having issues about 1 1/2 years in to owning the fridge and finally died 2 weeks ago.

Refrigerator caught fire - I own a 2003 Whirlpool Gold side-by-side refrigerator that I bought new from Lowes in 2003. On Friday, July 13, 2012, I woke up to the smell of burning wires. I called 911 and they sent out a fire engine. While waiting for the firemen to arrive, my neighbor came to help me determine where the smell was coming from. Within seconds, we heard loud clicks and a huge cloud of gray smoke came out from behind the refrigerator. The firemen arrived, entered the house, unplugged the refrigerator and told me that the smoke and smell was coming from behind the fridge.

Bought a New Whirlpool washer. Was ok at first then began to have problems. Called a repairman. Only to find out it was made in Mexico and was a piece of junk!! So in order to fix it the cost was 300 dollars. Then I was told that all the new washers were not so good. My heart broke. If you need a washer youre in for a problem. Look to see where they are made. Theres more new washers in the junkyard than ever. Buyer beware.

I had a 14-year-old 40-gallon tank that was working great but I decided it was time to get it replaced. I picked out a Whirlpool 400-gallon tank stated to be good for a family of 3 to 4 people. Immediately after installation, I got complaints from family members that there was no enough hot water for morning showers. I turned up the thermostat to the maximum 140 degrees, but there was still wasnt enough hot water. The Whirlpool rep on the phone stated that 3 people cant take back-to-back showers. The unit wasnt designed for this. I told him the unit is advertised for a family of 3 to 4 and I have only 3. I asked where on the advertisement does it state 3 people cant take back-to-back showers? His response was, Where does it state you can? I asked his name and he would not give it to me. If 3 people cant take showers on a unit stated to be for a family of 3 to 4, something is wrong. Maybe it should be advertised as suitable for a family of 1. I will not buy a Whirlpool product again and I advise others to take my advice, go elsewhere.

Whirlpool Range Model XFE381LVS - 12/13/2014 4:30PM Wife was cooking dinner and turned oven on. Smoke started coming out of the back and called me. I ran to the breaker panel and turned off the breaker. Back to the stove, pulled it out and smoke still coming out in back at the top. I could see fire in the top of the back panel. Slowly the fire went out. Unplugged the stove, I removed the back panel, wires were still smoldering and the Control panel was burned thru. Took pictures so I could contact Whirlpool Monday. The Electrical control panel is destroyed as well as many wires. Glad we were home and oven was not left on while we were out in the yard or Home could have been destroyed. Purchased the stove from Lowes 11/02/2010 with a extended warranty. Tried to add receipt but would not accept, wrong type doc.

I purchased a new Whirlpool range and had it fitted for propane. I used the stove daily and within two weeks, the temperature started fluctuated constantly. Several things I tried to cook ended up burned. I called Whirlpool to ask them for a possible solution. They wanted to send a repair person. I live on an island and knew it would take forever to get someone here. My appliance person said it could be only two things - the temperature probe or the computer board. I purchased both things and had them shipped to my address at my expense. It cost $257.00 to get the items. My appliance man on the island installed the two new items. I was hoping that would fix the problem. I am sad to say it did not! The oven still fluctuates wildly. I set the temp for 350 degrees and it shoots up to 450 degrees. I turn the temp down to 325 and it settles in at 350 for a period of time. Then, without any warning, it will shoot back up to 500 degrees. I have to open the door and let the temp back down to 350. This is how I have to bake and cook with this disaster. Wish I never purchased a Whirlpool appliance!

The washing machine continued to display an F1 error code. I contacted the manufacturer and was told that they will not do anything about the problem due to it being out of warranty. This is the first time I have complained about a product or service and want to try and assist anyone who may be thinking of purchasing a washer from Whirlpool. I do not recommend purchase of these units.

Big bang for your buck. I have used Whirlpool for years without any needed repairs. Typically you may see brands began to fade as you use them. However, the Whirlpool brand microwave always seem to stay true to its form. As long as you keep the inside clean the microwave should last a long time.

Whirlpool gold bottom freezer is 2 years old. This model has a design flaw. And due to this the drain is frozen in the bottom of the freezer. Water is leaking onto the floor. I called for service and whirlpool is charging me. To fix a problem that is their fault. This is unfair.

Whirlpool duet steam model: WFW9750WW00Serial: CSY3601165Please see attached the pictures of our washer that was purchased without a top counter balance from HH Gregg in May of 2010. We were told by the extended warranty technician when he came to diagnose the machine on 6/24/13 that the bearing and basket were bad. He ordered the parts and returned on 7/2 to repair the machine. Upon taking it apart, he discovered the top counter balance was missing and was the reason that the bearing and other parts had failed. I will include pictures of the plastic that the counter balance should have been attached to. You can see there are no screw holes or scuffs on the plastic. It was suggested by one of the customer service agents, Kitty in TN, that we remove the counter balance. Per Kitty, Because had it come from the factory like that, it would have walked all over the laundry room and not worked right since the first day. Honestly, we have scuffs all over our walls and my husband just thought the legs needed adjusted or it wasnt sitting properly on the pedestal. We have never owned a front load washer, so we didnt know what to expect. The washer sits in a very tight space under the cabinets, but will walk in the middle of the floor especially before we installed the pedestal.The top counter balance was ordered on 7/2 and we were told it would arrive and be installed today. The technician called me at 10:55AM today and stated the package had not arrived. We are asking Whirlpool for a replacement washer as the one we purchased brand new came from the factory defective. We have been told a solid NO. Upon further inspection of the machine while taking pictures, I noticed that the bottom counter balance is cracked clear through as well. Im attaching pictures of that. I did speak with Laticia in MI. She was VERY nice and more empathetic than the other 6 or so people we have spoken with at Whirlpool customer service. She was professional, helpful and I hope who Whirlpool would want representing their company and brand.We feel Whirlpool sold us a faulty machine and they should replace it. We have been told by them that they are sending the parts as a GOODWILL gesture, and will have the parts installed. Now after the whole inside of it is shot and possibly the motor and boards, thats awesome. We are now an LG/Samsung family. This was our 3rd and last set of appliances from Whirlpool. When the rest of these die, we will replace with another brand. How sad that what once was a great company, and I grew up with my mom and grandma thinking there was no other brand to use beside Whirlpool, now we are left washerless for 3 weeks. They refuse to stand behind a mistake that was made in the factory. Ive read these are made in Germany. Maybe Whirlpool needs to bring jobs back to the US and improve their quality control.

We bought a new brand Whirlpool, ice berg, 2 door refrigerator in 2006. It worked fine for 6 months and then started giving all the problems. Until now, we have repaired it at least 10-15 times with company servicemen and also private repair shops. We are just so tired and frustrated will all that we have gone through because of this fridge. Today, the main door just came out and it is probably the 16th incident. We are hardworking people and take a lot pleasure and find lot of happiness in buying something new. It took us almost 2 years to save money for this new fridge with cost us about Rs. 20,000. But I should mention this that we have already more than Rs. 10,000 in repairs.I am sure this would just be another email in one of your inboxes but wanted to write this and convey the message that we are hurt. We do not want to take any legal actions as middle class men in India do not have the resources to do that. But I would surely not buy anything of your brand going forward and would not suggest anyone for it. Writing this in assumption that you understand the pain middle class men goes through to but something worth Rs. 20k and spends another Rs. 10k for repairs. We had high expectations from your product but that was not to be.Following were the problems we face in last 4 years: 1. Refrigerator not cooling (5-7 times); 2. Top door broken (1 time); 3. Main door broken (1 time); 4. Water leak problems (5-7 times). I hope someone will read this and forward it to concerned department.

Purchased the fridge from hhregg in August/September 2012. Model G16FARXX. After less than three years of owning it, found out today that the compressor is shot and will have to be replaced. Replacement/repair costs are ~$900, almost as much as the fridge brand new. Chatted with customer support and then would/could not do anything. I feel ripped off. If it happened after 5 years of use, then my attitude would be different, but not a major component going out in less than 3 years.

I have had my refrigerator for more than 10 years. It is a standard refrigerator with no extras and I have never had any problems with it. I think things that dont have too many extra built into them are better with not so many things to break down.

I bought a Whirlpool WFW9470 Front Loader Washing Machine 11 months ago. The washer appears to complete a wash cycle but leaves the washing wet and with no error message or light. Whirlpool says the machine is not designed for light loads. The technician says washing on a light load will damage the bearing. We had the spin bearing replaced after 8 months. But still, the washing remains wet and the bearing wears out prematurely.

French door style leaking water on the floor. Is Whirlpool covering the repair?

I recently purchased a top of the line self-cleaning Whirlpool/KitchenAid range. Or so I thought. I used the self-cleaning feature for the first time only to find out it literally does not do anything. Whirlpool quickly answered my Saturday morning phone call and were very professional. When I told them the Aqualift did not work, they asked if I purchased the Aqualift kit. No, what does it contain? Two sponges and a scraper. Basically I was told I would have to clean the oven manually. That would be fine except I have osteoarthritis and cannot clean it manually. Shame on Whirlpool and KitchenAid and Consumer Reports for not doing their due diligence and not testing important features accurately, over a greater period of time with real day-to-day scenarios with people who actually know what they are doing.

My 2010 Whirlpool refrigerator stopped working, due to a compressor issue. I need to purchase a new device ASAP.

This microwave had been the best I have used for several reasons. One is the modern design that goes with our kitchen. Two: it heats the food very quietly and produced an even temperature through out the food. Three; The inside of the microwave is easy to clean out.

For the most part, the dishwasher performs well, but I wish they would ask the input of women when designing appliances. I just can’t figure out how having spikes on the top and the bottom racks is supposed to help in organizing your dishes better for proper cleaning.

I purchased a Whirlpool Cabrio on October 27th, 2010. The Cabrio is always giving me the UL code, which indicates the load isnt in balance. Ive been doing laundry for 27 years. I know how to load dirty clothes into a washing machine evenly. Sometimes it will take me all day to do one load of laundry! Seven months after my purchase, my Whirlpool Cabrio washing machine started giving me the F51 error code. I called the phone number on my Lowes receipt for warranty work. Two weeks later, I finally had my washing machine running again. I was happy and thought Id only have to deal with the UL code. Boy was I wrong?!Now Im two weeks away from my warranty expiring. Im getting the F51 error code again! This washing machine is an $800 piece of junk! Hopefully, I can get the Cabrio repaired before my warranty expires in two weeks. I do a lot of laundry. We are a family of six. So, I know Im hard on washing machines but come on. Shouldnt an $800 washing machine last at least two years? Im not even a full year into owning this junky washer and Ive had two breakdowns! In my opinion, this washing machine needs to be recalled and people need a reliable replacement or refund.

I bought this washer (Whirlpool Cabrio) about 4 years ago. A year or so later, it started leaking; based on reading the troubleshooting guide we found that this was because the feet would continually get out of balance. After painstakingly re-leveling the washer every 6 months or so the washer now consistently leaks - even though its balanced/level! $508 to repair a machine I paid $787 for. No thanks. I agree too with the other reports that it doesnt get clothes clean. I just figured this was a feature those of us got for trying to be energy efficient.

In March 04 2014, I purchased a Whirlpool washing machine. After having had a Whirlpool for 17 years without any problems with it, I purchased another one. This last one is a piece of junk. I dont even want to talk about the noise, I think it is expiring or on its last leg. They should fire the engineers that invented this model and bring back the other engineers that invented the one I had for such a long time, they far surpassed these space scientists that they now have. On August 8, I called Whirlpool, they sent me someone from Dinos appliances. This man tells me that there is nothing wrong with this machine and that he re-calibrated it. Whatever that means, it is still not wringing the clothes properly. There are only 2 people in my household, so my loads are not very large. I even tried this Drain & Spin cycle after the wash was completed and the clothes still came out too wet. I also have a Whirlpool Dryer and I will not replace it with the same brand. I also will never buy a Whirlpool product again and will make sure that I will share my experience with everyone I know.

Whirlpool model EVLl201NXRQOO, serial no. EWT2423236 - Defective paint on the back of the freezer that caused rust to form and paint to peel off. Whirlpool does not warrant manufacturing defects on the paint. Guess I was lucky for it to be on the back and not the front.

11 months after I bought the fridge it started acting up. I paid 1900 for this thing. The temp kept getting warmer and the ice maker quit working. I had to pay for a service plan. Ill never buy a piece of junk Whirlpool product in my life again and ill broadcast their poor quality to everybody in my 5000 congregation. I work to save up to buy this product and its junk. Ill end donating it. Im very upset at this junk product produced by Whirlpool.

Have had no problems and we have both washer and dryer Duet and love them. We need to make sure we keep the washer door slightly open to avoid mold. The dryer lint filter is a little difficult to vacuum out.

Good washing machine for 3 year. 4th year onwards your repair cost starts increasing. I purchased machine for 24 k. Now my repairs costs are 25 k. Each time the service guy comes puts me a bill of 7 k and above. The complaints to Mr ** goes to deaf years as he never picks the call. Their visit charges also are more and never give warranty above 30 days. How will you feel when you have paid more money on services ce than the product. I have supporting hills for all.

In July 2012 I purchased refrig, ed2khaxvb (model #). By Oct. 2014, after numerous service calls to unplug ice blocking chute, an ENTIRE door was factory ordered and DELIVERED. Feb 2015, A&E service installed new door. Later that day, I opened the freezer door which had insufficient suction and ice is again sliding down the chute to the floor. The stress this has caused me (87 yrs old). Case #, phone and ref..nos. could fill a book. PLEEEZE HELP. What can I do???? Ty.

Whirlpool is not what it was before. I got this set with new house... They are very poor construction. They are not even close what I have before the LG. After 6 months I begin to have problems with the dryer... Technician come two time to fix the problems. Quality of washing is OK though... That going to be the last time I got Whirlpool products. For sure.

My first time with Whirlpool (Always had GE) but at the suggestion of our builder, we went with Whirlpool and the stainless steel is horrendous. Nothing will clean it or make it look STAINLESS. My refrigerator, dishwasher, double oven, tall vent all look terrible no matter what I use! I have never had this problem before. Im embarrassed to have anyone go into my kitchen...

We bought a new Whirlpool refrigerator about three years ago. Because of space, we had to purchase one with a top freezer and also with no ice maker. First of all we didnt realize it was much deeper than our old Kenmore so it stuck out further into the kitchen space. That was not that big of an issue. At first everything ran great including the top freezer compartment, or so we thought. Then we noticed that when we had ice cream in the freezer and put water in ice cube trays to freeze, the ice cream would get very very soft. This continued to the point that now anytime I put water in there to freeze ice cubes I have to turn up the temperature to keep the ice cream frozen. Once the ice cubes are froze, there is no problem, but they take at least six hours to freeze. Then one day when a young child slammed the refrigerator door closed, the freezer door popped open about an eighth of an inch and then closed again. So, I tried it. Anytime you close the refrigerator door a little too hard the freezer door pops open. I then tried the dollar bill test to check the strength of the seal. The bill pulled right out of the door with very little effort. So, is the problem bad seals, bad design, or bad quality control, or what. How can I be assured that the frozen foods in the freezer are being frozen as solid as they should be. I know they dont freeze solid enough in the freezer door. I will eventually dump this refrigerator and go get another Frigidaire. If we have to get one with a bottom freezer, we will just have to rearrange our kitchen to accommodate it. But, having to turn the temp up and down every day is ridiculous. I have had issues with food close to the walls in all refrigerators slightly freeze, but never had an issue with keeping things cold enough. I will never buy another Whirlpool refrigerator, stove, or anything else for that matter. I have always had good luck with Frigidaire, so I will stick with what I know works.

I have been a dedicated Whirlpool customer for 50 years. I purchased my new, Cabrio washer and dryer in 2011. The dryer works fine. The washer does not. It ties everything in knots. Most everything comes out in one large, wrinkled lump. When washing sheets, it wraps the whole load in a soaking wet, fitted sheet bubble. You cannot wash one item by itself, because it will become unbalanced and shutdown. I will say that I havent had any repairs yet, but I have a feeling, its only a matter of time. I have decided to buy a new washer, but it will not be a Whirlpool.

We bought a Whirlpool with convection oven, it is beautiful and very well designed and fully electronic. You can only control it via touchscreen Which, when the software runs into blocks, it is impossible to troubleshoot efficiently, you just have to wait until it completes its rebooting. It is very frustrating to spend hundreds of euros in a device you just cant control when it crashes. Horrible programming made for a horrible user experience. You have the feeling of not being able to use it or fix, it is like having a mobile phone or computer Which only works on what appears to be a random logic. The errors displayed on the screen are often vague and the user troubleshooting manual is just plain short. We will return it without doubt and dont recommended ever buying this device.

This fridge is very spacious in the fridge area. The freezer area is larger than a model with freeZer on top or a side by side model. The black stainless steel is very attractive and doesn’t show fingerprints. The controls for the fruit and veggie drawers are cheap. The drawer for meats and cheese is huge. Overall I like this fridge.

In 2012 we bought three new Whirlpool kitchen appliance back in 2012. The refrigerator has needed a drain pan replacement, and two air diffuser replacements. Of course, both air diffuser issues occurred just outside the one year warranty. Then the range oven has required two spark modulator replacements – again just outside the one year warranty. Whirlpool’s solution: buy another 1 year warranty to get it fixed; or buy a new Whirlpool appliance at a discounted price.

Apparently, Whirlpool selling all their rejected faulty washing machine in the market. The trick they are playing is the machine being sold with one year parts-labor warranty; They wont replace these machines with a new one because they know that these machine will never work, consumer will buy the faulty machine, obviously it wont work so consumer will call for service. The service guy will say that “oh! Machine needs a part and then the customer service will say “the part is being ordered”, “wait”, then the service guy will come with the part and after wasting some time he will say “Oh! The machine needs another part, and again customer service will tell the consumer that “you keep calling us”. One year will be gone! Bottom line – faulty machine is sold, Whirlpool made profit, buyer is robbed. I am one unfortunate customer who purchased Whirlpool Washing Machine which never worked as it is a faulty machine which should not go to the market at all; Whirlpool made money on my hard-earned dollars and I been robbed.

I purchase newly Whirlpool washing machine but it was not working from the first day of my purchase. So many service Engineer came but nobody can solve the problem, so I suggest to all please don’t buy washing machine from Whirlpool. I am very disappointed from this company.

Ive had my Whirlpool Refrigerator for 2 years. Within that 2 year period, all 3 of the drawers within the refrigerator have broken and now there is a crack in the freezer on the bottom starting in the front and going straight back on the bottom to the back and up the back. After pleading my case for a new fridge to their Customer Satisfaction Department and everyones supervisor therein, theyve offered to pay for the epoxy repair. Im very dissatisfied with this! I dont think that a $1300 fridge should be held together by glue after only 2 years. Ive been waiting for one of the drawers to be replaced for over 2 months. They claim that the crisper pan is out-of-stock and they have no information if it is in production. Im to call back in 2 weeks to find out the status of that part. I would like to add that my husband and I work 6 days a week and our adult children are rarely here, so this refrigerator is very lightly used. We dont have a household of 6 or 7 people constantly home, opening the doors and sliding out the drawers. The fridge that I had previously was a GE and it lasted 30 years. I guess the next one will probably be a GE. I just wanted something different. Well I got it. Its something broken.

In 2002, I purchased an EE3Z50RD055V 50 gal. Whirlpool hot water heater. Recently several solder joints on the computer module became unsoldered so I cleaned the joints and resoldered them. But several months later another joint became unsoldered so I thought Id just purchase a new module. I called 1-877-817-6750, explained the problem to the young lady. She informed me that they would ship me a new one overnight. I asked her how much this would cost and she told me there would be no charge as it had a lifetime warranty. SURPRISE! Thats what I call customer service! A few years ago, I purchased a Whirlpool Duet front load washer and dryer. Now Im twice as glad that I did. My wife and I LOVE the Duet.

I have a Whirlpool oven and dishwasher and have had nothing but problems with them both since day one! Our oven went out Christmas and couldnt get service on it and we were entertaining for Christmas. DONT EVER BUY A WHIRLPOOL PRODUCT!!! If you do you have no one to blame but yourself.