I first want to begin by saying that we have been a Whirlpool family for years. I now own a Whirlpool microwave, hot water heater, washer/dryer, Jenn-Air stove and dishwasher. My problem now is with the Cabrio Washer purchased in 2008. I started having problems in 2011 and the same problem has raised its ugly head again. When I try to use the Clean cycle, it starts at a 60-minute cycle and goes down to a 2-minute cycle in 3 minutes without cleaning or even running water into the tub. This time, it made a terrible noise and stopped. The tub was replaced in July 2011 after having the same complaint as above. The repairman said that the mechanism on the tub to fit into the spinning cycle is made of plastic and is not holding up. Also, in March 2012, a new control board was installed. I spoke to Whirlpool Customer Service and they informed me that they did not have any other complaints about the Clean cycle and that I should call the repairman. Luckily, I purchased an extended warranty. I vote a thumbs down on the Cabrio washer.

I just bought a brand new Sterling steel refrigerator not even 2 months ago, and since I got it, noticed rusty spots coming out,and now has spread all over. I called customer care, and they said it wasnt cover under the guarantee,and to buy a special spray out of my pocket expensive to remove the rust. I am Very disappointed with the service I received, for its not even 2 months old refrigerator and it looks like it is old now. In addition, the company didnt offer to send someone to take a look, checking and make sure theres no future problems with my new purchase, and as a courtesy removing the rust free of charge.

Whirlpool Cabrio top loading washer model WTW6800WW1 - I bought this washer 3 years ago. It cost me about $900. It has become very loud. I had the repairman here yesterday fixing my dryer. When he heard the washer, he told me the bearings are gone and its just a matter of time before the machine dies. To fix it involves a total rebuild of the motor, about $600! WTF! This is my 3rd washer in 19 years. There is something seriously wrong with appliance manufacturers. They no longer care about their reputations, and just produce crap! Expensive crap! Needless to say, I am now shopping for our 4th machine, which will be a Speedqueen basic washer with a 3-year warranty!

I have owned my Cabrios for over a year. They have given me no problems at all! I keep them cleaned with Affresh, even though Ive never ever had a smell in them. Also, I have never ever had my washer or dryer not do its job!! My clothes are fresh as a daisy and clean. I bought my Cabrios because my father purchased his first set and raved about them. So, I used his to try them out. Absolutely wonderful machines!! You get more area without those crappy agitators in the way for one thing. Always fresh water, not washing in the same filthy water, yuck! It wasnt but maybe 4 months later for our new house that we got our Cabrios. I insisted on them! LOVE LOVE LOVE my Cabrios!!!

Purchased a Whirlpool refrigerator July 29, 2015. Our first service call was August 4, 2015. The units freezer was frosting over, the basket rails were covered in frost, which made it hard to open. Items in freezer containers were covered in frost and labels unreadable. The interior light was frozen shut. Since the first service call we have had 8 service calls with multiple appliance dealers. No one can fix the frost issue. It just keeps recurring. Whirlpool did step up and extend our warranty for another year. In order to schedule a repair we have to call Whirlpool, a 45 minute phone call for an appliance company not of our choice to make the service call. The unit has been removed from our home for repair in dealers shop. Very inconvenient for us to have no refrigerator. Whirlpool has refused to replace the unit, choosing instead to patch-patch-patch one service call at a time. Whirlpool has enjoyed years of an excellent reputation. We are very disappointed. This is no longer true.

Cabrio Washer WTW6600SW1 - We purchased this washing machine back in January of 2007 and have had nothing but issues with it. We thought Whirlpool was an upstanding brand and weve found out otherwise. They havent stood behind their product or the issues we have had along with all the other people. There has been a Facebook page about the Famous F1 error code. We have had numerous other error codes we have had to pay to have someone come out to fix. We paid almost $700 for this machine and have had to pay out several hundred more dollars just in repairs. Not worth the money and the company doesnt deserve to be in business if they dont back their product. I get buying a warranty, but if they are same problem with so many machines, it sounds like a manufacturing defect to me.

Whirlpool Range Model XFE381LVS - 12/13/2014 4:30PM Wife was cooking dinner and turned oven on. Smoke started coming out of the back and called me. I ran to the breaker panel and turned off the breaker. Back to the stove, pulled it out and smoke still coming out in back at the top. I could see fire in the top of the back panel. Slowly the fire went out. Unplugged the stove, I removed the back panel, wires were still smoldering and the Control panel was burned thru. Took pictures so I could contact Whirlpool Monday. The Electrical control panel is destroyed as well as many wires. Glad we were home and oven was not left on while we were out in the yard or Home could have been destroyed. Purchased the stove from Lowes 11/02/2010 with a extended warranty. Tried to add receipt but would not accept, wrong type doc.

I purchased a Whirlpool dishwasher and refrigerator/freezer from Home Depot. Within weeks the stainless steel on both products began rusting. They sent a third party repair service to look at both products and determined that, in fact, the stainless steel was rusting. Our technician said that both the dishwasher panes and the freezer doors would be ordered and replaced the following week. This was on September 4, 2015. After several promised arrival dates, the parts never arrived. I called both the third party repair company and Whirlpool on several occasions only to be told they were on back order. Finally, in late November, the new dishwasher panel arrived and was installed. It is now December 17, 2015 and our freezer door is still on back order. When asked what my options are, the Whirlpool representative simply said we have to wait. I said that because I have been so terribly inconvenienced that they should just come and pick up this piece of junk and replace it with a new one. Evidently, that is not an option. I will NEVER purchase a Whirlpool product again as they do not back their warranty. I now have a $2,000 rusted refrigerator freezer to adorn our beautiful Christmas kitchen. Thanks, Whirlpool. Youve certainly made this a Merry Christmas. (Yes, sarcasm in play.)

I purchased the Whirlpool touchscreen gas convection range and I do not recommend this product at all. The oven cannot operate without using the touchscreen to set the temperature and it has a mind of its own. Woke up in the middle of the night and the oven turned itself on to 550 broil. I called Whirlpool, they sent a tech out who replaced the touchscreen and the same problem is happening. Not engineered very well. The range would have been fine without the touchscreen, if only it had an old fashioned knob to set the temp. I do not recommend buying this appliance.

We have ALL Whirlpool appliances in our home. This was our second home so we were not here to use these for a long time. We were preparing our other home and our parents home to sell. Our French door refrigerator is almost 2 years old and we live here now. My husband opened the icemaker door to see why we dont have ice. There was a wire in there. We called the local Whirlpool authorized service man and he said the wire is not hanging down to connect it. He tried to channel a new wire and said it must be crooked in there, he cant get through the insulation (no channel). He asked us if anyone had ever worked on it. We bought it brand new. Home Depot delivered, unboxed and set up. He said we need a new door. Whirlpool will not stand behind this! I am so disappointed! I thought I was doing the right thing. Good name, made in the USA. I was wrong! I definitely do NOT recommend Whirlpool!! I am so sorry that I spent so much money on 3 homes of Whirlpool appliances!!

I guess I am in the lucky group because my washer lasted about 3 years before the problems started. The latest is the lid lock light flashing, the machine doesnt go through full cycle but stops in the middle, doesnt spin and drain. Even before that the clothes didnt come out clean. The repairman said that this product is basically disposable and it makes more sense to buy a new washer than to invest in fixing this one because something else will break next.My old White Westinghouse lasted 18 years without one problem, Im sorry I wanted something new. What a pity that companies nowadays sell junk and the consumer has nowhere to go with a complaint. Im wondering if someone has the name and the address of the CEO of Whirlpool, I would like to ship that piece of junk to where it came from... it would be funny if other customers did the same. And I agree with other posts that class action suit would be in order... too bad nobody started it yet. I wish I had read the reviews before I made the purchase but at least I know now to stay away from all Whirlpool products and do whatever I can to prevent other people from making the same mistake I did.

DOES NOT MEET CONSUMER NEEDS AS PROMISED. I wish I read the reviews. Very expensive machine I purchased specifically for the large drum for large loads. The machine cannot handle large loads (if you consider one blanket large load). I have to unplug the machine mid wash, as the load gets stuck on one side and moves my machine across the floor. The noise in the spin cycle with even small amount of laundry sounds like a helicopter is about to land. Then last night I noticed black oil splattered all over my floor. This is a $800.00 machine. Never ever met my exceptions as the machine promised to deliver. Theres very little water that enters the drum... Not even my towels come out clean. DO NOT BUY WHIRLPOOL... EVER EVER EVER.

This is a portable dishwasher with a butcher block top. Great to use as a rolling island countertop. The capacity is huge, fitting large pasta pots and dutch ovens with ease along with dish plates. Love the water miser setting and the no heat dry to protect delicate material like china dishware.

It was on sale and the price was good for comparable refrigerators. The biggest problem is that instead of a simple dial to control temperature, you have to be a computer genius to figure out how to turn it to a different temp. even by the instructions. And the ice maker throws ice all over the floor even if you hold the glass up against the top. When I first got it, it made a very loud noise when it run, but that changed with time to a bearable volume. Everything seems to work well other than those few little things.

We have a Whirlpool top freezer that is a very basic model with no bells and whistles. It is over 20 years old and has had no major issues. Tears in door seal have occurred but is to be expected with age and use.

I purchased a Whirlpool microwave oven from American Furniture/TV in Fenton, Missouri on 11-13-2010. It had a Whirlpool 1 year warranty and a Performance Guarantee for five years. I noticed recently that the plastic on the door had hairline cracks near the handle and now is beginning to crack around the glass on the front door. I called American when I noticed the cracks by the handle and was told that it was cosmetic and not covered. Now the cracks around the glass may be a bigger problem if they let fumes out from the microwave. I am waiting for a second answer from American. I feel like the problem is with the plastic itself.

The washing machine started leaking and making a noise like a freight train 6 months after purchasing it. We complained in February 2011, but the parts were not available until March 31, 2011. The same problem occurred in September 2011, and we are still waiting for the parts until October 18, 2011. In the mean time, I have been spending hundreds of dollars doing wash at the laundromat.

Moved into a house with a 2009 Gold Series Dishwasher model GU2475XTVY0. It has never worked since we moved in 3 years ago, always left dishes musty and poorly cleaned. We basically used it as a rinse/dry and pre-washed everything by hand. Even then it would mold up frequently and required manual cleaning. Total piece of junk, but looked really nice, stainless finish. Yeah.Latest chapter is it completely stopped working. Called a tech out for the usual $80+. His advice: this is a total lemon, and has been from the start. Not worth repairing. So Whirlpool, is this the standard you have now? 5-6 years for a dishwasher life cycle? Noted that my fridge is a matching 2009 Gold series, it has also had several problems with keeping a steady temp and has gone through 2 control boards at a hefty fee each. I guess Im done with Whirlpool, running out of appliance brands to blacklist here...

I have posted on here in the past about the problems with the Cabrio Washer from Whirlpool. Our third top load lid was just ordered since 2011. There is a design flaw where the plastic frame around the lid cracks and causes the lid to hump up. While shopping at a local appliance store recently, I saw a new Cabrio washer and the lid and hinge system has be re-designed. I wonder why?????

I have purchased offloading washing machine in 13 Oct. Within three years it has given lot of problems. Every third month we have to call for service and spend lot of money. We had changed drain motor and condenser. Wiring is faulty. Machine will be down many times.

First off, took five weeks to get the damned thing delivered after buying it at Lowes Home Improvement. Have problems with the drain overflowing when the washer tries to empty. Major plumbing work to rectify that. My complaint with Whirlpool is the washer doesnt work. It will partially fill and then stops. The wash light then lights up and nothing happens. I let it sit for three hours and the clothes never washed. It took an act of God to get the washer to empty. It never did spin the clothes. The washer refuses to work through the cycles. $1500 wasted on this POS! Trying to get an appointment scheduled is equally frustrating on Whirlpools website. Never again will I buy Whirlpool!

Had washers model # WTW8500DCO repaired after being install for 14 days. Have had washers repaired every 90 plus days because of constant electrical and mechanical failures. Would not ever buying another whirlpool appliance to my worst enemy. Customer service is a total failure. If you ask a question after talking with you for 5-8 minutes and they dont have an answer they start saying HELLO, HELLO? I have to hang up. I cant hear you. Just a really sad business. Stay away!

Dishwasher is 15 years old and still going strong. Minor leak which disappeared when I cleaned the gasket. Good internal arrangement for fitting dishes & silverware. One of the best appliances I ever got!

I called Whirlpool about the refrigerator that I purchased in June of this year and nothing was done about it. My situation is that the refrigerator scratches very easily. It seems that it gets scratch only by looking at it. This refrigerator is very expensive and I not even done paying for it and this appliance looks awful!! Susan the person that I was chatting with just told me that cosmetic doesnt cover and there is nothing that Whirlpool can do about. It bothers me that paying so much money for something that it is poor quality material.

Whirlpool fridge with serial # EL2427127 started on fire. Flame started on own but filled entire basement with electrical fire smoke. All terminals on compressor completely melted off. After researching online, I see Im not the first. Unbelievable.

Front load washer Whirlpool Model# WFW9400SW02, only had this machine for about five years and the main interface control board has gone bad. This part cost 1/2 as much as buying a new machine. My parents had the same washing machine for almost 30 years and no problems. Whats wrong with this picture?

We purchased the microwave. It looked nice and seemed sturdy. I bought a trim kit to make it look Built in. As soon as I finished installing the microwave and kit we tried to use it. My wife could not get the door to open unless she pushed the door button hard several times. I checked to see if the trim kit was causing the problem and it was not. We kept trying to get the door to open as it should but could not make it work correctly. I even used a little lubricant and it did not help. We then looked up the reviews and saw this was a prevalent problem. We then returned the unit and trim and ordered a Samsung. It will be in on the 25th of March. I placed a review on Lowes site but Whirlpool removed it saying since I took it back they removed the negative review. Since it was defective I wanted the public to see the truth on this unit.

Whirlpool Cabrio Platinum Washer - The seal on the top of the drum is breaking down. It is cracking at the bleach and soap dispenser. Somewhere in the washer drum or plate is causing holes and cuts in the clothes. The machine is only 2 years old.

Bought a nice house in 2012 which has a Quiet Partner 3 Dishwasher. About twice a week it has to be reset pressing buttons because it blinks at you when you press start. Control board was replaced a couple times since we bought house. We just put up with it. The tub has a manufacturers defect in bottom where the plastic is so thin it finally cracked and over time water trickling out went to wall. Then ruined an area in finished basement ceiling. Ive used a couple different things to stop the leak but it always starts leaking. Customer service says its not under warranty so will buy a new dishwasher. But not Whirlpool or Maytag. Same company now. Dishwasher is a total piece of crap.

In July I purchased a Whirlpool Gold oven and cooktop from Lowe’s. It was delivered in Aug. after a 5 wk wait, since it had to be ordered. Since installation, the hot surface light on the cooktop stays on. I called in & was told to try resetting the elec. breaker. Did that... still stays on. Model G7CE3034XB00, Serial D43005649. On Sept. 4th I called & spoke to Carrie (I believe in TN) who told me she would try to find a service tech in my area & would get back to me in 3-5 days. Apx. 5 days later she called & left a message on my cell phone stating that she could not locate a service tech in my area. I would need to find my own service tech & submit any invoices to the resource dept for reimbursement. Parts could be ordered at no charge. I have nothing in writing from the company to confirm I would be reimbursed, nor was I told how to correspond with the resource dept in the event I had an invoice to submit for reimbursement.Today, Sept. 18th, 2014, I called Whirlpool again (800-253-1301) & talked to Stephanie in Michigan. She told me the same info. When I asked to be sent a wiring schematic I was told I didnt need one. When I asked how to get in touch with the resource dept. I was given a fax no. & email acct. When I asked how I was supposed to get in touch if I didnt have either, she said I should go to the local library. Now lets imagine for a moment that I am disabled or live so far out in the country that I cannot get to the library... How am I supposed to get to a fax or email acct. Has anyone at Whirlpool considered that? This is a new appliance under full warranty, yet it has become my job to find a service tech, pay up front, & wait for reimbursement. REALLY??? I am also in the market for a new dishwasher & you can bet it wont be a Whirlpool!

I initially purchased all new Whirlpool products as part of my new home purchase in a Pulte subdivision, June, 2011. My WP microwave failed to heat in 2012 and the replacement of the Magnetron and Inverter and service was covered under warranty (would have cost me $493.51). Sadly, the microwave again failed to heat in 2014. I was so disgusted with this second failure, I decided to live without a MW until January, 2016 when I paid for my second service call and learned, once again, I needed a replacement Magnetron and Inverter, to the tune of $400. Both servicemen told me the 2011 magnetron/ inverter mechanisms were new technology and did not last long. Again, sadly, when I contacted Whirlpool, they would not admit to their defective product line and indicated they could do nothing since I am out of warranty. It is unconscionable that a corporation is not liable for their defective products.

We have a Whirlpool washer wtw5640xw2, we have been experiencing burning wire smells for some time. We had bought the extended warranty. Lowes sent out a repair company. They replaced the main board and the problem has continued. This has been as intermittent problem with the burning smell. We experienced it this week really bad! I thought the machine was on fire. We called the repair company and they said they had fixed the problem. My husband called the Whirpool number and they said they would NOT do anything to help us. We are trying to get help from Lowes where we bought the washer. I am terribly afraid to use the machine. This model needs to be discontinued.. We bought this machine 5-07-12. If we dont get some help, we are going to our lawyer.

I have had two Gold Series dishwashers before but the model number I used had been discontinued so I purchased the W10491035A about a year ago in 2013. It has to be the worst dishwashers I have ever had and we have used them for forty years. Its loud. It won’t dry the dishes, and unless you wash I dont mean rinse, most of dishes are not clean, and that is with the recommended detergent. Whatever you do I would suggest not buying this dishwasher. I dont even know why they would offer a machine such as this.

Its a great machine but the temperature control button is easily moved at times. The machine does a great job in washing clothes. Ive had mine for 10 years now and hope that I never have to replace it.

I purchased this washer (Whirlpool Cabrio Model #WTW8000DW) 10-25-17 from Best Buy & now it has no power to the panel at all. The power to the outlet is fine which I can plug a hair dryer in & the hair dryer works. Tried all the reset buttons & options with nothing on the panel working as well as unplugging. Still nothing. It is barely 4 months old & I am very dissatisfied for the amount of money I paid for a high efficiency top loading washer.

Whirlpool customer service is non-existent. I have a Whirlpool microwave that burned up after two months of use, and they sent over a technician twice, in the past three weeks and it is still not working. Now, I am being told that it will take another two weeks before the correct part is found, and the technician is sent here again to fix the problem.I have no microwave now, for what is going to be about 5 weeks, and that is only if they get it right this time. Whirlpool wouldnt approve for me to have it traded a trade for a new one at HH Gregg where I purchased it in Aug of 2011. HH Gregg only has a 30-day return policy, and it went bad after 60 days.

My elderly mother purchased a Whirlpool Cabrio washing machine in 2013 (Model Number WTW8600YW1). It never filled properly with water. It evolved to a sensor and circuit board issue that Whirlpool never totally remedied. Hence, the machine never worked properly. This 800 dollar purchase on an elderly persons limited budget had to be utilized minimally. Now fast forward in 2015, even with minimal usage and white glove handling, the machine is displaying an F51 error. You guessed it, Whirlpool will not remedy the issue, although it is well-documented to be a widespread complaint hence clearly a product defect. Shame on Whirlpool, their business practices, and what amounts to theft of an elderly womans finite income. I have advised my mother to trash the useless Whirlpool appliance and purchase a Kenmore washing machine, of which I have been the proud owner for 10 years, doing laundry for a family of 5.

I dont think I ever bought another product where one of its highlighted feature does absolutely nothing. Using the Aqua Lift cleaning process is a waste of time and electricity. We were told this range had a self-cleaning oven when we bought it. If a self-cleaning oven is important to you buy something else.

Ice maker will freeze up every couple of week. I cleaned it all out last Saturday and today, Friday, it was frozen up again.

We have a Cabrio washer and dryer. The Washer has had problems since year one. We have just gone through service with Sears to fix a rusted out hinge on the lid. The tech broke the lid trying to drill out the rusted screws. He ordered a new lid and six weeks and one day later came to put the lid on. This was terrible. We were rescheduled two times for our appointment. Today the washer will not start on the cycle when you press the start button. We will never buy another Whirlpool product and not Maytag if what I read is true. Probably will be six more weeks to get this resolved.

I purchased this washer 3 years ago. At year 2, I had to replace the RPS part. The codes that appear represent 2 different issues as well: one being the RPS part and also for the control panel. In less than 1 year since this replacement, it is broken again! The clothes do not get very clean. You cant soak whites in hot water and bleach (it drains after 5 minutes if you stop it). You have to use the bulky setting to get enough water to actually wash your clothes. If you get too much detergent, your clothes comes out crunchy feeling even with the extra rinse.I thought this Whirlpool product would be great since my 22 year old dishwasher is a Whirlpool and still works but as the old saying goes... They dont make them to last like they used to. To say this washer is a POS Lemon is an understatement! I also have the companion dryer and it is starting to have problems including the door latch breaking into pieces. I will never purchase another Whirlpool product again! I have been told that Kenmore and Maytag are also under the Whirlpool umbrella so Im not sure what I will buy next. My recommendation: DO NOT BUY THESE PRODUCTS!!!

We are so disappointed in the purchase of this machine! It doesnt put enough water in the machine to clean the clothes, and the spin cycle has continuously gotten louder and louder to the point I think its going to explode when it spins! Is there any recourse we have or any recalls on this machine?? Thank you for your help!!!

Ive owned my Whirlpool appliances for almost a year. So far Ive had 4 maintenance calls for my dishwasher to be fixed (over and over) and once for my refrigerator. Yes, its currently under warranty, but Im afraid to keep it without an extended warranty due to all the issues Ive had with them. So, now Im going to be spending hundreds on an extended warranty. I will never buy another Whirlpool.

My landlord purchased a new Amana washer (NTW4605EW0) Labor Day weekend 2015. It started having issues in the spring, so we went through the process of utilizing the manufacturers warranty. Apparently, Amana, part of Whirlpool, requires 5 attempts at repairing the machines before replacing. Okay, so starting in June 2016, we arranged service appointments 5 times and replaced 1 part, then another, 4 times. Clearly, that part is defunct. Right? Fast forward to September and then into October. Get a new washer, and not the one I preferred. We got the Whirlpool WTW4816FW1. Before the installers leave, we are having the SAME issue. Stops midcycle, doesnt finish cycle, sometimes stops while filling, or while full, or kid wash, or mid drain... But now with the new washer, the drain and spin cycle thinks it should FILL instead of drain... and Whirlpool said they would get someone out the next day, a promise they cannot keep because they dont supply the repair guy, they source with local companies. So, the company ordered 3 parts... That could be the problem. And 4 days later, 2 parts are on freaking BACK ORDER. Parts arrive. All new parts replaced. Machine still doesnt work. Outlet tested by us and them and it is fine. The techs think there is some kind of RF interference. Turn off sensor light, which is on the same wall, unplug power to wifi router (which outdates the washer). Still, doesnt work.I have spent half my week, every week, since June, restarting my washer, unplugging the damn thing, waiting, and waiting, trying again and again and again to wash 2 loads of laundry a week... Literally takes a week until the damn thing does its job. Whirlpool is sent us a replacement washer. Can you guess what happened the first time we started it? SAME ISSUE. Cycle will not complete. Sometimes it dies before it even fills. Sometimes it dies while filling. Sometimes, it will fill and fill and drain and fill and fill and drain and... never stop filling. Or, the fun one, the drain and spin cycle thinks it is suppose to fill. Continuously. And then, suddenly, after unplugging it for 1 hr, or 24, or 72 hrs, it will work fine for 1-7 cycles. Nothing is consistent except that it doesnt work consistently. HAS ANYONE HAD THIS MUCH TROUBLE???

The machine meets our needs and just the right capacity. It has just the right number of selection for proper washing. Very easy to load clothes and remove from the washer. There were a number of colors to select.

Had kitchen remodeled and purchased this microwave. Now after three years the door cracked in several places and now it will not heat food. Now we will have to replace this mess. Never buy any Whirlpool appliances again!

The pilot light went out on our Whirlpool hot water heater. We followed instructions and were unable to relight. Our plumber was also unable to relight so we ordered new parts with associated overnight express costs. The plumber returned and worked for over an hour. When the pilot light came on the burner assembly burned out the new thermo coupling and that needed to be replaced again. This happened again. I would like to join the class action suit as Whirlpool has known about this problem and consumers are paying more than the original cost of the unit for repairs.

I bought this fridge 2 years ago. I had multiple repairs already. Now the side panel makes noise when you shut the door. Repairman told me it is the foam separating from the side panel. There is nothing that can be done. I also have extended warranty.

I am the owner of a 4-year-old stainless steel Whirlpool refrigerator, Model GB9SHDXPS02. Yesterday morning, my 5-year-old daughter opened the fridge door to get a snack. The door came crashing down, hit the floor - missing my 21-month-old daughter by less than two feet - the drawer smashed off on impact and flew across the kitchen floor and the contents of the drawer (salad dressings, syrup, condiments, etc) went flying too. Miraculously, no one was hurt. My children were obviously upset and crying, and I was shaken. My laminate floor has a large dent and long scratch from the impact.My fridge door is broken. I cannot get through to Whirlpool Canadas corporate office to speak to anyone. The Whirlpool Canada call center is giving me the runaround. Yesterday I spoke to a supervisor at the call center who advised me that someone from the Corporate Safety Division would phone me within 24 hours - but I have not received a phone call and it has been more than 24 hours. I am noticing a complete disconnect between the gravity of the situation and an appropriate response from Whirlpool. I am a mother of 4 small children - two of which were very nearly killed/badly injured by a faulty refrigerator door. I cant even get a phone call in response. This is a serious safety issue. Im tired of apologies, some real action needs to be taken to ensure this never happens again to any consumer.

Whoever came up with the idea of this AquaLift oven cleaning method should be fired! This method does not work. Ive barely used my oven but had some cheese pizza drip on it so thought I should clean before using again. What a JOB! The spill did not come off the bottom entirely and using the non-scratch scrubbing sponge was a joke. There is some soil on the sides and back of the oven that I will have to use elbow grease to get off and Im going to have to crawl into the oven to see if they can be remove. Welcome back to the old days before self-cleaning ovens!

This complaint refers to model number ET8MHKXMB. It was purchased in November of 2008 and the fan had to be replaced on May 29, 2012. The cost of this repair was $189.79. This is a terrible thing to have happened. Obviously, the fan was made cheaply. We are very dissatisfied and will not purchase another Whirlpool refrigerator ever!

I moved down to Florida in March of this year. I have always owned Whirlpool appliances and wouldnt think of buying another brand...... till now. I purchased in March a new washer and dryer set washer model #WTW4800XQ4. The washer is so noisy that I cant watch TV while its running (what a piece of junk). I asked when they installed it if there was something wrong with it and the gentleman from H&H Gregg said no, they all sound like that. I guess if you want quality you have to buy Japanese.... HOW SAD.

Just like a lot of other people, I bought a Whirlpool hot water tank because of the good name. And just like the other people, my tanks pilot light will not stay on, it will be on for a few days and then you get up and no hot water.

I have had our Whirlpool Cabrio washer and dryer (CU0771356 and MU0803512) for four years. Our trouble started when the machines were 14 months old. The numerous error codes have been fixed by replacing boards, the bearing has went out, and the entire tub has been replaced. The dryer has had two service calls for going out. Now, both are out again. The washer pump is bad and the dryer has stopped heating up. Where is the class action lawsuit?

Purchased a Gold Series Whirlpool dishwasher, Mo. No. WDT720PADW2, From Maruszcak in Schererville, In. on 1-29-16. Approximately a year later door was replaced by Whirlpool because of paint problem due to faulty design. Replaced door is now peeling and rusting by exhaust vent also. Contacted Whirlpool and they will do nothing more. They said it was a favor the first time they replaced the door. They feel this is a cosmetic problem! I paid a total of $675.03, Their repairman would charge a $100.00 to look at it and another $235.00 for a new door. I feel this is a design problem and they should replace it with a new model, a refund would be better. Very unlikey, because Whirlpool does not stand behind their products. The line also includes Maytag, Jenn-Air, Amana and Hot Point. Besides this I have found plastic pieces that have fallen off! I had to use plastic ties to keep them in place. Dishwasher does not clean well. Have to rinse everything first. Products are bad, stay away from them!

I purchased a Whirlpool water heater and after working fine for about 2 1/2 years, I began having problems with it staying lit. I dealt with troubleshooting beginning in January of 2012 and finally in March of 2012, I was sent some replacement parts. The unit worked fine through the summer and once the weather started getting cold in October of 2012, I began to have problems with the unit again. After a couple of months complaining and threatening to file a BBB complaint, I was sent all of the parts left to change on the water heater. And I was told after the parts were changed if the unit still did not work, that it was probably a venting issue and that I would be responsible for that issue and the unit was not defective. I received the parts on 12/04/12 and they were changed out the same day. Now the unit will light when I hold down the button to light it but once I let go, the pilot light goes out. At least before changing out the parts, the unit was able to be turned on and sometimes it would work and other times it didnt, but now it will not light at all. This is very frustrating because the unit is under warranty and Whirlpool has for an entire year fought me tooth and nail just to send me the parts for the unit, only for the unit to still not work. I have a family and it is discouraging to not know when you are going to have hot water, having to constantly fix the unit or to call Whirlpool to troubleshoot and finally for the unit to still not work after replacing the parts. It looks like I will not have any hot water at all now.

Something inside the machine broke causing it to tear up my clothes! I had it repaired once, now it is 4 months outside warranty and it is destroying my clothes again. Whirlpool will do nothing to help remedy my problem. They did offer to help repair it at a cost of $350. Not happy with my Whirlpool washer. Looking to replace my 16-month old washer.

I purchased my Cabrio washer and dryer 2 1/2 years ago, and for the past 6 months, I have dealt with it being unbalanced and I tried everything to get it balanced. When I researched the problems, I found so many other consumers are having the same problems and that Whirlpool will do nothing about it. I decided to start a petition on Change website to try to force Whirlpool to stand behind their product and correct the problem, offer us a refund or another product, or even fix the darn thing. It is tough economic times, and we spent money to have something that was energy-efficient as well as a product that is supposed to carry a good name. I am a single mother with three children, and I dont have a $1000.00 to throw away after 2 years. This is shameful that we, the consumers, have to deal with this. Please go to the Change website and sign my petition. The more signatures I get, the more leverage we have to deal with Whirlpool. Lets pull together and show Whirlpool we will not stand for them robbing us of a quality product. Thank you so very much.

We purchased a Whirlpool Dishwasher from the Home Depot, it was installed 3-28-2015, less than 30 days ago. On 4-21-2015 the dishwasher stopped working. I called Home Depot expecting a replacement; but we were told you have 48 hours; you need to contact Whirlpool, due to the CRAP warranty. I called Whirlpool, we were told that a TECH would need to come out and address. They came today, ** , told us that the Motor is bad. (NOTE I havent made a payment on this dishwasher). So we called Whirlpool, expecting they would replace. I spoke to ** who advised me they would not replace, only repair. I explained this is unacceptable for a new product. I demanded to speak to her Manager; Spoke to ** who said the same. I asked to speak to her manager, his name is ** , but HE DOES NOT DEAL WITH THE CONSUMERS, this is beneath his job class I was told. So NOW I have no choice but to have this Dishwasher repaired; it will take over 2 weeks to get the part. I just dont understand how this is good Customer service. It is the worst I have ever experienced.

Love my new fridge, not in love with the icemaker though. Every couple of days I have to reach in and scoop the ice off the little shelf in the back, or else it will quit making ice. The ice cubes block the arm from coming back down to trigger a refill.

I just purchased a brand new home. I have an electric wall oven with the microwave over the oven. They are both built into the wall. Can anyone tell me why a massive amount of steam is coming out. It is really bad it makes my microwave glass so bad I can see through it. It is also making my cabinets so wet I have to use a towel to dry them. Plus I got a steam burn. Can someone tell me if this is normal.

The washer itself doesnt get the clothes clean. The clothes on top never get clean, they smell. It doesnt spin out the clothes evenly even though I put them in evenly. There is oil on my floor under the washer and Rent-A-Center doesnt care and its under their Benefits plus program. They were to send off both washer and dryer last time and had no paperwork where washer was sent off at all. It has ruined a lot of my clothes with spots and I used the Tide pods. Stopped using them cause they were not working. I will never buy another Whirlpool product or appliance. Water pump went out in one year... Why would you not care about your customers... I got this set in 2013 and its the Platinum line triple top loader. You lucky to do one load at a time, a single load that is...

Whirlpool gold bottom freezer is 2 years old. This model has a design flaw. And due to this the drain is frozen in the bottom of the freezer. Water is leaking onto the floor. I called for service and whirlpool is charging me. To fix a problem that is their fault. This is unfair.

I purchased Whirlpool gas range. After approximately 1 year, it has repeated problems with oven failing to maintain temperature. The unit would remain on, with the bake on still showing. But the temperature would decrease to the point of not cooking the food. If you turned the oven off and then back on, it would preheat again and resume baking, only to kick back off again later (again, with the bake still on).

Bought a Whirlpool Freezer on bottom in Feb 2012. Its December 2015. Only had gotten a 2-yr warranty. Wished I would have gotten a longer one. About a yr ago the freezer started leaking water all over the bottom of the freezer which turned into a sheet of ice... then leaking water all over the floor. Now there is a knocking/clicking noise coming from the back of it. This product is only 4 yrs old and Im praying it doesnt give out on us. That was an almost $2,000 purchase. I was hoping to at least get 10 yrs out of it. Never buying a Whirlpool Fridge again.

We purchased Whirlpool Cabrio Washer Model #WTW7300DW0 and Dryer in 2013 from Home Depot. The washer is the worst appliance we ever owned. It makes a horrific metal rubbing noise during agitation. The Whirlpool assigned repair service provider, after 2 trips and $300 has been unsuccessful in repairing the problem. Even after he called Whirlpool direct for assistance. Given that we used a Home Depot Gift Card for purchase, the repair expense is rapidly diminishing any benefit to keeping the machine. Well not even consider purchasing Whirlpool again.

I love my Whirlpool 4.7 cu. ft. top load washer because it has a pretreat station that is super handy for pretreating stains in a handy little place. The agitator is stronger than my old washer and really gets my clothes cleaner. Its also very quiet and easy to use all the buttons. The best feature is the deep water fill that you can select for more water.

I purchased 4 Whirlpool appliances late 2014. The French door refrigerator close to a year later made a piercing sound several times during a day. I immediately contacted Whirlpool and the representative directed me to YouTube to listen to the normal sounds the refrigerator would make. My first thought was I have been a homeowner for 30 years and countless appliances and never heard such a horrible sound. At the same time they sold me an extended warranty over the phone. He assured me sounds were covered. The sound just kept getting louder and more frequent. I could not take this piercing sound and called back. They sent a local repair service. At the time the repair person came out the refrigerator was not making the sound. I played a video recording and the repairman even said what an terrible sound it was. He continued to check everything over and said - everything looks good. I dont know what the sound is coming from. I asked, What is Whirlpool going to do? He said, nothing, the warranty ran out and your extended warranty does not cover sounds. What a ripoff! Now the drawers broke and another thing they wont cover! I also have problems with the dishwasher I purchased at the same time. Even putting on the extended hot dry I need to wipe everything off. I should have just open a window a tossed out over 2k. The sound is so horrible I am being forced to junk the refrigerator and purchase a new one. Dont purchase Whirlpool and never purchase extended warranty over the phone.

We bought a Whirlpool cook stove with a black top in 2009 and this year, in 2011, while cooking a pot of stew, the stove top burner began to make loud popping sounds. When I went to check it out, there was smoke coming out from under the pan and pieces of glass that had exploded out in small chunks. When calling the customer service line at Whirlpool, they told us that it was no longer under warranty and could not be of help. Their only explanation was that they would only cover a new stove top if it had cracked or broken this way when putting a cold pot on a hot burner. They said their technician could tell if this was why the shards of glass were exploded from the burner.

My mother and grandmother swore by Whirlpool washers. They were the best. So, naturally I never wanted any other brand - then came the digital machines. End of an era. My experience with my 1 year old digital machine has been very frustrating. I do not like it. I prefer the old system.

This product is very noisy. This product looks good, works okay, size is good but is very loud and overpriced. Probably would not buy again if I had to purchase another refrigerator.

I have a rental home and my residence, I have purchased a fridge for BOTH places. Within 1.5 years, both of the fridges shelving cracked. Customer service will not do anything to remedy this. It is a known issue with his model of appliance. There are numerous complaints and they DO NOT stand behind heir product. NEVER BUY WHIRLPOOL.

It goes off balance, frequently. It is moldy and stinky. I wipe it out, use a cleaner and leave the door open, but it still stinks. I am getting rid of it and buying a Speed Queen top loader. I am extremely disappointed in the front loader Whirlpool.

I bought a matched set of Whirlpool washer and dryer. Within about 3 months the dryer quit running on any of its cycles except heavy duty. About a month after that the washer started messing up. First it quit putting in the bleach. Next it quit adding water except under the heavy duty cycle. Then after about another week or so it quit putting in fabric softener. After a couple of more months it only uses hot water. Now not quite a year after I purchased it the washer now only adds water in the wash mode and not the rinse cycle. Now all this would not be a problem except I had lost the warranty cards and in their website would not let me register it online.

In 2013 my oven died. Upon doing some research my husband and I went to our local appliance stores in search of a new one for a good deal. We chose a Whirlpool electric range with convection oven. We have had it 2 1/2 yrs and have used it often... until today we had been very happy with it. While baking some French fries we heard a loud pop, almost like a shot, running to the kitchen to find the inside tempered glass shattered! Wow! Shocked to say the least we couldnt believe it. Called our Lowes store, to no avail our warranty had expired. They gave us Whirlpools number with no success. I am extremely disappointed and will probably never buy Whirlpool again!

Whirl Pool Duet Wash WFW9400SW - I had this washer for 5-1/2 years. I use it about 3 times a month. Warranty ran out this last February. Machine stopped working. Called tech and he came and said I need a new console and power board. Two weeks later I get told they dont make it anymore and sorry about your luck. I used this washer under 200 times in 5 and half years. Whirlpool offered nothing and I will never buy a Whirlpool product again.

I purchased a Whirlpool Cabrio washing machine April 2016. I was so excited to have a new washing machine. I thought the 1st couple times I used it I just didnt have settings right. It uses so little water it doesnt get all clothes wet. If they are not wet they cant be clean. So I started doing very small loads. Then clothes were not clean. They stink. So I have tried every detergent out there. Nothing helps. Another thing it takes an hour or longer per wash to get not so dirty clothes. Not to mention it puts holes in my towels. I tried reaching out to Lowes where we bought it only less than 4 months ago only to be told they would contact Whirlpool. Whirlpool wanted to send tech that I would have to pay for just to tell me that the piece of crap washing machine is doing everything the manufacturer made it to do. I told him I was not going to pay so. I think with all the problems people there should be a class action lawsuit. DO NOT BUY CABRIO!!!

My new fridge is extremely hard to open. The technician that was sent out told me that there is too much suction building up inside the fridge and freezer and that is why it has to be yanked to open. This is not only annoying it means the fridge is constantly being pulled forward out of place. Technicians solution was to deactive the castors under the fridge. At the time he was here I did not realize that I could then no longer move the fridge out of its place to clean. I called Whirlpool and complained and was told that they could do nothing more for me because the fridge is in good working order. I hardly would call this good working order. They also informed me that if I wished to clean under the fridge or the coils at the back it would require a service call to move the fridge and I WOULD BE CHARGED EACH TIME. Needless to say I AM VERY, VERY UNHAPPY WITH THE WHOLE SITUATION.

I have used Whirlpool products for over 30 yrs. This is the worst made product I have ever purchased. The ice maker doesnt produce very much ice. The cold water on door isnt cold. There is too much wasted space in freezer and refrig. side. You cannot get anyone to call you back to call for help. I contacted Whirlpool over a month ago. No return call yet. Consumers beware!! Model no. WSF26C3EXF01.

Eleven months after purchasing a Whirlpool refrigerator for our office lunch room it stopped working. While the refrigerator was still under warranty, I called Whirlpool for a service call. I was informed that the warranty is voided because the unit is located at a business and not a residential property. I explained to the customer service agent that there is no mention of this policy until after the appliance is purchased. After a considerable amount of time on the phone speaking with several supervisors, I was connected to a Resolution Specialist. She informed me that this policy is available online for consumers to view prior to purchasing Whirlpool appliances and it is the consumers Due Diligence to research warranty policies before purchasing. Consumers beware! Warranties are voided on all Whirlpool appliances that are located at a business address.

Thrilled with my first experience (9 years now) with my Whirlpool glass-top range/oven. Truly LOVE the modern look of glass cooking surface which cleans up like a dream! NO harsh abrasives needed, always WIPES shiny and beautiful. All-electric...no stinky gas fumes. Wonderful features... Computer controls, SELF-CLEANING OVEN. Now, if only it would do the prep-work.

I bought a new Whirlpool gas hot water 40 gal tank from Lowes. I Installed it, but the pilot light would not light. So Cal Gas Co came out and said they did not like the new design, but that was how they were now making them. Gas is shot out from a pipe into the tank, however its fairly open. The pilot ignitor is similar to the one on barbarques that often do not last. You cannot get to it to light it manually. Several calls were made to Whirlpool and they sent a repair man out to fix it. You can imagine buying a new hot water heater and having it work part time. The repair man explained that the unit needed a new thermopile, but he could not put one on until whirlpool authorized it, which they would not. After a rather heated conversation with whirlpool they agreed to FedEx a part overnight. Of course the repairman could not wait for me to call and had to come back again. The pilot light still does not stay lit, and Whirlpool now wants to talk about how the tank is vented. This has nothing to do with the pilot light, nor did putting in a new 1/2 gas line and valve as per Whirlpools request. Whirlpool has a problem and they refuse to acknowledge it. However, it is Lowes that chose to buy from whirlpool and they do little if anything to stand behind their product and gain consumer confidence. My suggestion would be dont buy whirlpool, and shop at Home Depot.

Sept. 2011 purchased new Whirlpool bottom freezer model GX2FDXVA03 and in Dec. 2015 had to replace it after paying for 2 service calls, last time was told cant be repaired. First found ice in bottom of freezer which was caused by Whirlpool installing a rubber nipple at bottom of drain line with such a small opening it clogs quickly. Couple years after that stopped working had to replace circuit boards, now its leaking Freon and no way to be repaired. If you call Whirlpool all you get is big circle of feel good call centers. Best offer was discount on new refrigerator. Told the person Why would I want to spend another $1300 on junk?

Another person with problems called this a giant Whirlpool paperweight and he is so right! I received delivery of a Cabrio WTW7800XW3 washer on December 17, 2011. I had an issue (stopped in the middle of the cycle and flashed the letter “F” on the control panel) with it on January 2nd. I called and scheduled service. I had unplugged the machine and a few days later I replugged it and it started to work, so I cancelled the service call. In March, the problem started again. It just adds a little bit of water and then stops. Since then I have had repairmen out 6 times with 8 new parts installed and the washer still doesnt work. Now, the control panel won’t work. Whirlpool refuses to replace the machine. The repairman says these are the worst machines (any of the ones that are top load and have a clear top) he has ever seen and that I should buy an extended warranty. He says the bearings in the tub wear out among other things. On one of the repair visits, the serviceman found a chewed up pair of baby pajama pants. The machine makes a really loud noise like a jet engine taking off whenever it spins and the clothes are not clean. Whirlpool says that the warranty does not cover replacement of a defective machine. I have since researched the machine and have discovered that there have been problems with this line of machine for years. So, why are they still selling them? I am hoping for a class action suit. The company should stand by their products. I will never purchase a Whirlpool (or any other brand manufactured by Whirlpool) product again. I have had the machine for 4 months and it has been usable for about 2 of them.

I am completely dissatisfied with the Whirlpool Cabrio top loading machine. Our washing machine is less than one-year-old. It doesnt get the clothes clean, especially the darks, and it is so rough on the clothes that they come out twisted tied into knots. The dark clothes come out dirtier than they went into machine. Even though we use the dark detergent on the dark clothes and program for an extra rinse cycle, the clothes come out with white powder all over them. They need to be washed again and sometimes again. And sometimes they still dont come out clean. That is not very energy efficient. The clothes come out of the machine so wrinkled that everything needs to be ironed. I can imagine making washing machine that doesnt do its primary function, which is to get clothes clean. Todays families do not have time for this extra work.

As soon as we bought our new microwave, I saw what appeared to be hair on the door. I tried to scratch it off but I could not so I wondered if it was a crack but I could not feel it. As time went by, many other lines appeared but I could not feel them, just see them. After a couple of months, I noticed the first crack could be felt and then soon after that I could feel the other cracks. The first crack goes from the glass to the edge of the door and is wide open and the door edge kind of just hangs there. There are now about 20 cracks and the door will most likely fall apart soon. I called Whirlpool and they lied and said there have been no complaints at all about their doors. I read them some of the names here on this site having the same problem and the best they can do is offer to sell me a new door for $180. I told them that their product was defective and need to be recalled or something and he again tried to send me to the parts department to sell me a $180 door. I told him if that is how Whirlpool treats their customers, I would no longer buy anything from them.

Only problem is you have to open door to access functions. 30 second increments and stop are on outside. Beautiful to look at and inside is easy to clean. 4 fan levels, vent inside or outside. 2 light settings. Nice and bright. Low profile over stove but big enough to hold large casseroles.

Within a few months after I purchased my gas hotwater heater, I started having problems with it not wanting to stay lit. It was purchased in 2004. I see that this is an ongoing thing with Whirlpool. Every time I would call them, they would give me stupid answers on what it could be. One lady got hateful with me. I have replaced every part several times and Im having problems. About every two to three months, Im replacing thermal couple. As of right now, Ive been without hot water for eight days. I called and he told me about a trip button that is in the little white thing that has wires going to the thermal couple. I push in on it and then tried to start my heater and it worked. They have never offered to replace it or even give me a discount on a new one. No one should be having so much trouble out of your hotwater tank. This is not normal. These are defective and should be recalled. This company is ripping the consumers off and we need to stick together on this and do something about it. Im afraid to buy another heater because I can see that the new ones are still junk. What do you do?

I own an FG flame lock water heater and have been having the same problems with the pilot light not staying lit. This is very frustrating! I have searched many websites and am not able to find a replacement thermocouple for the stupid thing. Also, I have been told that the parts for the type of water heater that I own is no longer available. I tried to call the Whirlpool number a handful of times, but unfortunately, I was on hold the entire time and could not speak with a rep. I guess that explains all of the complaints I have read on here. I would like to be contacted or have help from someone regarding this matter! I would not recommend this product to anyone and I am very dissatisfied!

12 months and 2 weeks, my ice maker quit working. I called Lowes where I purchased this top of the line junk. The first thing they asked was do I purchase the extended warranty. I said no. He advised to call a repairman he recommended, but I would have to pay for the repairs. Whirlpool was just as bad; no warranty, you pay. It appears they are both relying on warranties rather than selling dependable products or customer satisfaction. A couple months later, ice forming on the bottom of the freezer, and puddles every couple of days in front of the refrigerator. I pulled the two draws out and removed the ice. Within a week, it was back. A $2400 refrigerator should last longer then a 1 1/2 years without falling apart. My Whirlpool dishwashers only lasted 1 1/2 years also.

Off balance, wont wash correctly. Familiar stories online. Wasted money on a washer that is not very old. Wont buy another one ever again.

We purchased the Cabrio washer and dryer due to the companys past reputation and our own past experience with Whirlpool appliances fully expecting to receive great performance and durability. We have had the pair just about 2 years and the washer started experiencing problems during the spin cycle. The unit would get out of balance easily and then it would stop without spinning, leaving the clothes very wet. Well, as our past experience had indicated to us the washer is usually much more reliable than the dryer, or thats the way it had been for us. So we only purchased the extended warranty on the dryer. Not being covered on the washer we located a local technician and he promptly diagnosed the problem as the transmission failed causing the noisy bearing and the failure of the unit to spin properly.Our tech quickly repaired the unit but this failure disappointed me to the point of contacting Whirlpool. Thats where I came upon this site and saw the multitude of complainers with the same type of problems and some that are worse than ours. Our purpose in this review is to add to the 1100 or more reviews that report the same kind of issues. We are now in the same mindset as the 1100. Will we ever buy another Whirlpool? Probably not, especially since it doesnt look like Whirlpool wants to stand with their customers to make it right. Customer support is just as important to us as the reliability we seek. I would much rather spend a bit more in the price than replace or repair the unit after the purchase. A little economics lesson for our friends at Whirlpool is that if you abandon your 1100 customers you will save about $440,000.00, but those 1100 will tell everyone they know of their problems with that product and as a result many thousands will never purchase a Whirlpool. So if we all influence 5 of our friends not to buy, then 1100 X 5 = 5500 people X an average price of $800 which equals about 4.4 million dollars of lost sales. Seems like a no brainer to want to stand behind your customers. We dont believe that any washing machine on the market should fail after a few months to 2 years. These products should be built to last many years and the maker of these products should have that goal.

Bought this because it was a Whirlpool product and liked how it was supposed to work at the store, HhGregg in Downingtown. Anyway one week in we started having problems, clothes not being washed well, and constant problems of dripping wet clothes, like they were never spun at all. Would have to readjust all the clothes, respin, most times we have to that that every time we wash clothes and have to respin more than once and even then, clothes have too much water left in them, so it takes forever to get our clothes dry. We have a service contract with Sears, we have repairmen out a few times. Get told, dont wash towels in it, only do very small loads, supposed to be a large capacity washer, nothing wrong with it. Now its worse than ever, terrible product. I want a different washer, its rusting at the lid, its only at the most 2 yrs old, it was expensive and am very, very frustrated!!! I want what I paid For!!! Whirlpool, shame on you for putting out such crap.On to my next problem with a Whirlpool range, again bought it because it was a Whirlpool. We had our Kitchen remodeled and the range I had was white. We needed a stainless steel range, Bought the Gold series AquaLift convection oven. This is the most horrible piece of crap. The convection oven does not cook as a convection should, food takes forever to cook on convection, reg feature works faster and hotter than the convection. In my old range I used the convection feature always unless I was baking a cake. Then used the AquaLift feature to clean my oven, it was not dirty , but I like a sparkling oven, so followed the directions, set it to clean. It looked the same after it supposedly cleaned the oven. Nothing was cleaned, tried it again, it was a little more dirty, something had spilled. I wiped out the oven, used the AquaLift self cleaning feature again, same results, old oven, self clean, the oven after a cleaning cycle, only ash was left, wipe it out, it was spotless. So I called for repair, the repair guy was here about 5-6 different times, tried this and that, replaced a heating element in the oven, turned the temperature up in the oven, so now when I bake, I have to figure out what temp I need to put it on. Tried that, even admitted that the AquaLift feature was a bust. I contacted Whirlpool, I want it replaced with a different model. This range is about I and a half years old, want to replace it but again was very expensive. Its a terrible product, it cant be a coincidence, that both newer appliances made by Whirlpool are terrible!!!! Combined they cost me almost 3000.00 dollars. I feel that I have been ripped off definitely did not get the great products that I thought I was buying. No response from Whirlpool, no satisfaction. I want them both replaced or my money back, take them out of here, they are useless!!!!! I will NEVER buy another Whirlpool product again, and have told everyone I know about the terrible quality of these products.

We just received our brand new Whirlpool washer and dryer from Home Depot. The delivery person started the washer and started the dryer and promptly departed. My husband immediately put a load of laundry into the washer, and he noticed there was insufficient water levels to adequately wet the clothing. Approximately 3 tablespoons of warm water were added at intervals of approximately one minute each. The water level never rose above 3 inches at the bottom of the tub despite setting the washer on the heavily soiled setting. After the spin cycles he removed the extremely damp clothing and it appeared that the machine had not properly completed the spin cycle and drained an insufficient amount of water from the clothing. He tried another load, and it appeared that the sensors were not working which regulate the water levels because most new machines use far less water. However this washer was defective. He then placed the clothes in the brand new Whirlpool dryer. The clothes ran for over five hours and never dried and the dryer never got hot. There was obviously something wrong with the thermostat. We are both disgusted and will never ever buy a Whirlpool product again. In addition because of the extremely poor response from Home Depot, we will never purchase an appliance from them again either. So sad that Made In America, which was on a sticker on the front of the machines, does it mean diddly squat these days.

I have a two-year-old top of the line Whirlpool Duet Steam washer. Cleaning performance is adequate at best, but my biggest complaint is about the visible mold buildup that collects on the water dispensing plate as well as on the detergent, bleach and softener dispenser and rubber lining of the washer opening. I have cleaned the removable detergent dispenser weekly since purchasing. The water dispensing plate has a continuous buildup of thick black mold that can only be removed with a tooth brush and bleach and only a small portion of those openings are reachable. I have cleaned the machine with Affresh as recommended and exactly as the manufacturer recommends. Nothing changes! I contacted Whirlpool and was told this was normal for all washers in which some moisture always remains and that I should continue to clean and leave the door and dispenser drawer open to allow the areas to air dry. So, I have done all of those things for the past year and nothing has changed! I received notification that a class action suit had been filed against Whirlpool for this mold issue but have not been contacted in any other way. Not only is this mold visibly disgusting but certainly is worrisome from a health perspective. When I contacted the company a second time, I was told there was nothing that could be done and it was in no way a design flaw on the part of Whirlpool.

Brand new Whirlpool dishwasher from PC Richards. Model #WDT710PAYB2. Dont buy one of these! In the store, I was turned off by the panel being on top of the door and not visible when the door is closed. I dont understand why anyone would not want to see the cycles and operation but my husband insisted that was a good thing so I agreed to purchase. Well, its horrible! I pressed the panel buttons the first time I tried to use it, and the panel switch is erratic and all over the place. For example, if I press Normal, the Heavy cycle button light goes on. When I hit start, all the button lights shut off. I finally get all the lights to stay on and hit start (after about 10 tries) and when I shut the door, the start button blinks and beeps! The dishwasher does not start. After many attempts, I got it to run, miraculously, for about 10 minutes. It emptied the detergent dispenser and left everything inside wet and slimy. Nice. I cant believe Whirlpool would sell such an inferior product. I have always been a loyal Whirlpool customer, but after this experience, I think its time to switch appliance brands. Now I have to be inconvenienced without a dishwasher after spending over $500 and wait for a repairman. Thanks, Whirlpool!

Do not ever buy a Whirlpool refrigerator. Sloppy construction, bins dont close, doors dont seal well and a brand new fridge doesnt cool to a safe food zone. When we call for service, I got the run around for almost 2 hours. They wont be sending anyone to service a brand new unit for an entire week... And thats 2 days before Thanksgiving! I have never had an appliance made this poorly. We dont have the space for a bigger unit, so thats why we bought this model. Size shouldnt impact quality!

I originally purchased a Whirlpool hot water heater in 2005. After numerous problems Whirlpool agreed to replace January 2010. With the new hot water heater, everything was fine for the first two years. Now about every 6 months, we are having the thermocouple and the igniter. Each time you order the part, the part is free but you have to pay $30.00 for shipping. I am tired of dealing with this. We have decided even though we still have a warranty left on the hot water tank we are going to purchase a different one and never ever buy another Whirlpool product. They do not stand behind their products.

Whirlpool Cabrio Washer - This is a horrible washer. I just read the reviews after having struggled with dirty clothes, smelly clothes, sour clothes and yes, our water bill is way higher using this nasty machine. I will never buy a Whirlpool again. Very VERY disappointed and dissatisfied with this machine. I usually always read reviews before buying anything but the sales guy at Garner Appliance said this was an awesome machine. We bought the matching set. And to read each and every consistently bad review with the same issues. They should replace these pieces of junk for us free. The dryer doesnt fall too far behind.

My washing machine is a front loader. Previously I would not have purchased one, but after using it for a year or so I have changed my mind. As long as I do not overload it my clothes come out perfectly clean using cold water, and partially dry so needing less drying time.