Whirlpool GX5FHDXVB03 french door refrigerator: Continual water leaks. Condensation freezes in bottom of freezer compartment then leaks out on to floor. Per repairman, this is a common problem with this model which theyll come out and fix (remove ice and run hot water done drain line for a cost nearly $150) but it will happen again and again, etc. I cant tell you how many times weve had to perform this task. This is an engineering design defect that Whirlpool should fix.

When purchasing a new home, the almost new Whirlpool double-door ice-dispensing stainless steel refrigerator came with the kitchen. This beautiful-looking fridge worked well for close to three years, but gave up the ghost shortly after its warranty expired; designed obsolescence perhaps? Problem was, it would have cost almost as much to repair as it would have to purchase a new fridge with a warranty. So, thats what I did, via a local big-box store. I bought a single door floor model, with the Whirlpool ending up as scrap, the whole incident leaving a bad taste in my mouth. If you have your grandmothers old fridge that still runs, keep it!

I purchased Whirlpool washer in Dec.2017 and used it in winter months only (Nov to March). It kept leaking and had to get appliance repair service for $50 and was told that machine is defective and whirlpool should repair it or replace it. I phoned whirlpool and they told me I have to use their appliance repair shop to evaluate the machine for cost of $130. The inlet valve was leaking and needed replacement for a cost of $253.55 and whirlpool shirked all and any responsibility. Dont buy whirlpool as it is not a good product and service is poor.

I purchased my Cabrio washer and dryer 4 years ago, my dryer doesnt dry completely, I have to do 2 to 3 cycles to dry. My washer has an f51 code and I have problems unlocking the lid and it takes 2 to 3 hours to wash. This is ridiculous and it causing my electric bill to spike. Is there a recall on the Cabrio?

Whirlpool Duet washing machine model WFW9500TW03 - Just after the first year of owning this machine, the metal hinge to the door cracked and the door didnt shut properly. It was replaced. After a couple of years, the bearings and drum of this machine failed. The cost for parts and repair were as much as the machine new. After repairs, the machine never ran quietly again. I have called for repair a second time for the same issue and he has confirmed that its the bearings again causing the drum to dislocate and hence, break the belt that I now need to replace. My problem is with Whirlpool for its defective metal in its machines (many complaints on the internet will confirm this). I believe there are enough consumers out there to file a class action lawsuit.

I updated appliances in new house, but didnt realize the builder would choose the smaller side by side frigidaire. Could use a larger freezer space, also would like a ice maker that cut off when bucket is full. Overall I love Whirlpool appliances.

The electric Whirlpool double oven range seemed like a good choice for a single person. I bought it in 2016 around the same time I had some personal setbacks. After finding my emotional equilibrium I decided to return to my much loved baking. While I have no other complaints on this range the ovens are a problem for baking. The digital oven temperature readout doesnt reflect temperature fluctuations in the ovens. Once you enter your desired baking temp the readout never changes even after you open and close the oven door say to take out cookies. Given some of my poor results I suspect even when Im not opening and closing the oven door the temperature is not maintained. I was going to get an oven thermometer but the user manual says it wont reflect an accurate temperature due to way the elements cycle to provide a consistent temperature. Ha! If you want to bake this is not the range for you. My inconsistent results and too often wasted ingredients frustrate me no end.

Bought this model from Bad Boy in 2006 and just after the warranty ended the problems began. We kept getting the F1 error code so with a little internet research we found it was a known problem with Whirlpool. I contacted them and was told they knew nothing about this issue being nationwide, however I emailed them copies of the complaints and responses. They sent out a technician who had to replace the motherboard free of charge. Next issue was a loud noise coming from washer sounding like a jet plane taking off. Hubby ripped machine apart to find the bearings blown apart and in tiny pieces. We ordered new ones and also found that when the new ones arrived they came with a tube of grease and a sealer to use so water would not get in later and cause more problems. Funny there was no sealer on the original bearings.Next the lid lock finally failed, ordered a new one but did NOT install it back into the machine, now it sits beside the machine. In case it fails again we will have total access to the laundry this time. Finally the UL error code keeps coming up. I refuse to put any more money into this machine again so I am allowing hubby to fix it if he chooses, whichever way he wants as long as no money is involved. So right now we have bungee cords holding the suspension rods tight to help with the uneven load code coming up all the time. Personal thoughts - DO NOT BUY WHIRLPOOL washer/dryers. They are crap and the company just does not care and they try to lie their way out of repairs if people have not done their homework.

Its supposed to be energy efficient yet it takes AT LEAST two times as long to get one load done, regardless of size or cycle preference! Now laundry takes all day! Literally! And why is there a lid lockout? Did someone accidentally fall in? If I drop something after Ive pushed start, I have to wait until the machine unlocks the lid. Why? This seems counterproductive. Its a top loader!

Our 27 cubic foot BLACK French Door refrigerator is freezing up again for the 4 or is it 5 time. We are now told they will give us a replacement and to go to the website and find what we want. The website lists DISCONTINUED fridges. Called their RUDE rep and found out only can get a Smaller, stainless steel ONLY refrigerator. So is that how they work, sell crappy refrigerators and then replace with a lesser refrigerator, which most likely will break down too. SHAME ON WHIRLPOOL. Or is it DEADPOOL. Your reputation is shot. We will NEVER purchase another piece of junk from you!!!

My husband and I purchased a Whirlpool French-door Refrigerator in Feb. 2014 from Best Buy. We did not purchase a warranty through them (BIG MISTAKE) because everything we heard about Whirlpool was positive, at least through friends and family. 1 year and 6 months later we have NO freezer and their warranty expires a year after purchase date! I called the company and they are no help at all! From all the comments I have read on here, there are few positive results! From now on I will be checking all reviews before I purchase a product again and WILL NEVER buy another whirlpool product again!

Washing clothes is a nightmare. I am constantly removing clothing from the washing machine that have been torn and left with holes. I am utterly frustrated. Because the machine is more than three years old, there has been no solution to my problem. I have now replaced clothing items in excess of $2,000. I am always here that they will send a repairman and yet there is still the problem. This machine is costing me too much money. The newer machines have fixed the problem. There is no gap between the drum and the doorway or rubber piece. I want that piece to stop this nightmare. This machine has taken a dream of mine and demolished the experience. I hate washing clothes but more so having a machine at home and then going to the laundromat to stop the chaos with doing laundry at home.

The pilot light went out on our Whirlpool hot water heater. We followed instructions and were unable to relight. Our plumber was also unable to relight so we ordered new parts with associated overnight express costs. The plumber returned and worked for over an hour. When the pilot light came on the burner assembly burned out the new thermo coupling and that needed to be replaced again. This happened again. I would like to join the class action suit as Whirlpool has known about this problem and consumers are paying more than the original cost of the unit for repairs.

I love my Whirlpool. Were a family of 3 with a pet dog. Its handle one childs work uniforms and the others sports uniforms (yuck). And then theres my work/weekend clothes. Its very reliable and it gets the job done. We have no complaints.

My son purchased the Whirlpool 2 door w/ icemaker about 3 years ago. Twice weve had a repairman here. Yesterday was the 2nd one. He tried 3 ways to get liquid to go through a round coil I could see at the back. He said the problem was between the two back panels (back of fridge & inside wall) where there was a tubing to release the water from defrost cycle. It appears to be a manufacturing problem. I am very upset! It should be replaced at the very least.

Purchased Maytag Washer and Dryer online from orange big box home improvement store. Washer had a twisted drain hose inside so it wouldnt drain right. Fixed that myself, but it still wont drain right. The spin cycle is weak at best - towels require a second, sometimes third, spin cycle. The dryer does not heat up like it should on the standard setting. The end of cycle buzzer/beeper on both units is truly pathetic... you better be within 6 feet of the machine when the buzzer goes off or youll never hear it. Having worked for a blue big box home improvement center for 7 years installing appliances, I know all too well the rabbit hole Whirlpool is trying to push me down. All I want is to return the Maytag and go back to a Whirlpool, but the not so pleasant lady on the phone with Whirlpool said all they can do is send out a technician, no returns on appliances. Buyer beware, be very aware!

This is truly a piece of junk! My water heater is 2 1/2 years old and the pilot light will not stay on. Was told that I needed a thermal coupler and paid $30 for shipping. Installed it and still the pilot light will not stay on. Was told again that I needed to replace the main control. Another $30 for shipping. Had that installed and the pilot light stayed on but no hot water. The light was blinking 4x (temperature too hot). WHAT!!? ALL I GOT WAS COLD WATER! Now I was told I need to replace the temperature sensor and they wanted another $30! I told them to I was going to junk it and buy a different brand.

I am experiencing problems with keeping my pilot lit too. I checked the screen and this is not the issue. I have just returned from Lowes where I purchased the water heater and they informed me Whirlpool supplied kits for this issue and it was widespread. They mentioned a class action and went on to tell me they and all surrounding Lowes stores are out of the free kit and arent expecting anymore. Am I to feel lucky my water heater water didnt fail sooner only to feel unlucky all of the free repair kits are now gone? Lowes provided me with the Whirlpool phone number for help and they have just informed me it will cost me $35.44 plus shipping. I now see how widespread this problem is. This isnt right. I am very disappointed in the handling of this known problem! What is my next course of action?

I purchased a new Whirlpool 3.6-cu ft Top-Load Washer (White-On-White) Model #: WTW4800BQ from Lowes on 11/1/14, which was only 3 ½ years ago. The washer began making noise during the spin cycle so we called for service. The technician claimed that the bearing pack needed to be replaced and the repair would cost $400. This amount is $20 higher than the amount I paid to purchase the washer. Because the warranty is only one year, I contacted Whirlpool today and spoke with a representative. The representative said they could repair it under the warranty. When I asked how to proceed, she then asked me if I had an extended warranty. When I replied that if I had an extended warranty, I would be using it. She declined any assistance. I now have to purchase a new washer after only 3 and ½ years. I own 10 rentals. I promise that none of them will ever include a Whirpool product again.

I have had a $3000 GE Profile fridge for 6 years. It died. Tech says turf it. I bought a whirlpool. Hopefully it lasts longer. These expensive fridges seem to be very undependable. What is a family supposed to do when a refrigerator stops working and repairs take days or weeks? Is there a courtesy fridge for a loaner? They are big and heavy. What a royal pain.

Bought a Whirlpool stove five years ago when I got my kitchen remodeled. In fact bought all whirlpool appliances stove, microwave, dishwasher, and refrigerator. The dishwasher and refrigerator have already had some issues which to me were because cheaply made. The microwave and stove are fine.

I have purchased two Whirlpool microwaves since 2007. The first unit lasted 5-1/2 years, the second one lasted only 2-1/2 years. I used it at dinner but several hours later it was dead. After reading other reviews I have decided it would be cheaper and less stressful to get a new one. So Tomorrow I will be purchasing a new microwave which WILL NOT be Whirlpool. I no longer have confidence in any of their products.

My new Whirlpool Stove, has two grill like tops, heavy duty and awesome looking. It has a special burner to keep food warm, a stainless steel front and bottom drawer for broiler storage. Broiler is also on top in oven, broiler flame.

I purchased a Whirlpool refrigerator with an ice maker exactly 2 years ago. It stopped making ice. I called a Whirlpool repairman and he said there was a leak in the freon tube. I should get a new one. I did, am trying a basic GE with icemaker.

Bought the Duet front loader washer and dryer. Nothing but problems and repairs. When I decided to throw in the towel and buy new machines my repair man convinced me to buy Whirlpool again - Cabrio. Said they are amazing. Love them except the holes in my shirts. I bag my delicates but apparently I have to bag everything. So sorry I bought them. There was a day when you could count on Whirlpool. Replacing my crappy Whirlpool gold refrigerator right now too. Hoping LG will be better. Already replaced my Whirlpool dishwasher. Went to Maytag. This company has gone downhill. My mom had these appliances for 20 plus years - I spend thousands and cant get 5 years!!! Dont buy Whirlpool!

Sent an e-mail to Whirlpool. They responded with apology. Sent a second e-mail telling them they should be paying the $300 for circuit board in a two-year-old range. No response. Also, sent e-mail to Geniers. No response. The impression I get is that neither are the least bit interested in the problem. Once they sold the $1260 range, they were done. We will never buy another Whirlpool from any store and we wont buy anything from Geniers in the future.

I bought a Whirlpool refrigerator, model # wrt779reyb00 with serial # vs13537798. The icemaker quit working and then water started leaking out from the door. A&E serviceman came out to repair and said we needed a new door. It had been over 11 weeks and the door still has not arrived and we have been told it could be as late as November. When I purchased an item, I expect it to work and if not, to be repaired within a reasonable time or be replaced. I have called and been told that replacement is not an option and that I will just have to wait. This is unacceptable. I purchased this refrigerator with water in the door and an icemaker and I expect it to work.

My machine has been ripping clothes for a few years but I thought, initially, that it was a snap, zipper or hook causing the problem. I recently got fed up and found this: **. It makes it pretty clear that it is a manufacturing defect. I called their customer service centre and spoke to a supervisor that told me it is normal wear and tear and that perhaps the glass in the door had worn out. Yes, thats right, she said maybe the glass has worn out.They are offering ZERO assistance in what would be a $500+ repair for me. Admittedly, my machine is five years old and out of warranty, but to me, when the repair is to install an entirely new style of door so that the clothes no longer get caught underneath, it is a defect. 43 different models of their machines are included in this issue and it was identified in 2012, a year before my machine was made. Why didnt they correct it before that?

I had bought from S C Shah & Co, Mylapore a Whirlpool ac 1 ton split magicool dlx cop in March 2016 and installed in March 29 2016 by Cool Control System, kodambakkam From the installation period we had a cooling issue and informed Shah & Co, Mylapore where we bought the ac. They came and checked and informed Whirlpool customer care. Within two months i.e. in May 2016 of installation Whirlpool again uploaded/charged the gas (the service engineers told us this is due to hot summer). Though again we had a cooling issue, we were under the impression as this is due to summer as explained by the technician. After that rainy season came and we didnt use the ac.As we are in December when we complained Whirlpool they said this is due to the copper wire gas is leaking and it has to be replaced and informed that though under WARRANTY, the customer has to pay for replacement (we have used only the 3 mtr copper wire which came with the ac only. we have not used any our own copper wire). Whether WHIRLPOOL GIVES SUCH A QUALITY COPPER WIRE which has to be replaced within 9 months. Now they are informing that you are calling us after 6 months of gas charging, so we cannot service. If you could have called within 3 months we could have serviced you. BUT WE ARE UNDER WARRANTY. NOT EVEN AN YEAR FROM THE DATE OF PURCHASE.Not responding to calls, disconnecting to the calls even if we call their Delhi number 011-49308500. Though under warranty they are not ready to do service and very rude saying, we cant do anything. So, if we buy WHIRLPOOL ac we have to beg them even for their technicians to visit our place. Or we have to do our own service EVEN UNDER WARRANTY. Their local toll free customer care numbers/service executives always give a recorded message saying they cannot service. SUCH A PATHETIC SERVICE.

We purchased a Whirlpool Overhead microwave and Quiet Dishwasher in May of 2017. Within the first year, the microwave needed new sensors installed. The repair person said this was a design flaw and he was getting many calls. Then at 13 months, the dishwasher wouldnt drain. The repair person fixed the problem and left reset directions because this can commonly happen. Now at 18 months later, the drainage problem wont resolve even with the reset. Whirlpool extended the warranty by 6 months but wont cover this repair. Two appliances, two problems. Dont buy Whirlpool.

Washing Machine Model WTW4616FW - I purchased this machine at Home Depot after I had to return my Samsung Costco machine that was recalled due to the glass top flying off. I was attracted to it by its simplicity in design and price. I have had it almost a full year and love it. I like that it has the deep water wash for over-sized items and a full-sized agitator. I was shocked that it was actually Made in America. I highly recommend it and I hope they keep making this reliable machine that gets the clothes clean. Awesome machine without the bells and whistles that I dont expect to breakdown. Way to go Whirlpool!

The Whirlpool I purchased has been the worst ever! Nothing comes clean even when I hand wash everything first and never has even from the beginning. I will never purchase a Whirlpool again. Now the machine wont drain I have gone through all the recommended steps for cleaning. The Whirlpool stove is almost as bad!

Whirlpool Duet Washer Trouble. Im having the same issue as Tom in Oakville. The F35-Sud errors pointed to the pressure sensor - NOT. 2 parts, a technician visit, and $800 later, Im still waiting on a Main Board replacement that is on nationwide back order. Time frame unknown.

I have called and emailed Whirlpool numerous times, complaining about the fungal odor emitted by my Whirlpool Duet front-loading washing machine (model #WFW9400SU01, serial#CSW0416732). I did everything they suggested that I do to no avail. A customer service representative said that the only thing left to do was to schedule a repair with a Whirlpool service person which I did. He called me when he was on his way and asked me what the problem was, and he told me I would be charged for nothing because hed seen this problem many times before and theres nothing he can do. Please advice.

I bought a Whirlpool dishwasher from lowest in May of 2011 and it stopped draining, serial # f11601686. I was told it was under warranty and you sent someone out. But surprise, I got a $129 service bill and it couldnt be fixed, computer board gone and drain motor shot. I was told its cheaper to buy a new one. After 10 months of use, we need a new one. I think you should replace my dishwasher and pay for a service call. Oh, the reason they said it wasnt covered is because they sold me a 2007 model.

Just got new side by side to replace old one. Motor runs every 30 minutes. Stays cold and makes ice but Im concerned about noise. Called Whirlpool and was told to record noise and show to Home Depot where it was purchased. No help from either place. Need to call warranty company. Funny thing it arrived with pieces of some sort of shrub in drawers. I guess this is new and improved and energy saving like newer washer that takes 45 minutes to wash a load.

Two years ago, we bought a Whirlpool gas range, model WFG361LVQ2. The range-top grates were porcelain-coated, smooth and shiny. The range itself has worked flawlessly (Admittedly, it gets only light use in our elderly household, which consists of me and my wife). The only complaint I have is that the porcelain on the grates is failing. On one of the grates, its flaking off where the flame contacts with it during cooking (Photos attached). On another two, the porcelain has developed a surface roughness thats clearly a prelude to same type of damage as the first. The fourth grate still appears to be intact. The differences in damage is no doubt due to the different amount of use that each receives.When I called Whirlpool, a supervisor there told me that grates have no specific life expectancy, and that is true for plain metal grates as well has porcelain-coated grates. She also said that some chemicals can penetrate the porcelain and shorten its life. I told her we didnt use any chemicals on the grates, but only rarely used common kitchen scouring powder, and I cant imagine the powder or the chlorine in the powder could do that kind of damage.When I asked what it would cost to replace the four grates, she said $187. I told her the entire stove cost about $500, and it didnt make sense to pay almost $200 to buy grates every two years for the next thirty years. I told her that the grates on our previous (non-Whirlpool) range lasted the life of the range - about forty years. So I declined to purchase new grates, despite her offer of a one-time discount of 25%. Though the grates are becoming eyesores, theyre still perfectly usable. So Ill hang onto them until I can find some bare metal ones to replace them.

After the pilot light on my water heater would no longer stay lit, I contacted the Whirlpool technical support number listed on the unit only to be told my unit was still under warranty, but I would be responsible to pay a $65 diagnostic fee and any labor associated with a repair. The technician came and said my ventilation system was the problem and didnt even touch the unit. He then sent a report to Whirlpool that the unit was flooded which voided my warranty. He did not submit photos to substantiate his water damage claim and now Im being told the unit is unsafe and must be replaced at my expense. This all sounds like collusion to not honor the warranty! I will never purchase a Whirlpool product again!

Cabrio washing machine - I have had the exact same problems as all of the above... lid locks occasionally ... after many frustrating tries. I am ready to pick up this stupid washing machine and pitch it in the junk pile! Soap on clothes so I have to redo ... except many times it takes forever to get the stupid machine to restart... Most times I end up rinsing things by hand in the sink. We are constantly itchy from soap residue. My clothes do not come out clean. Especially the towels. Clothes are not spun out as much as they should be... Have been doing it over again by hand many times... which is not good because They still have way too much water in them and it takes 2 -3 Times longer to dry them! I am so disappointed in this set. I always thought Whirlpool was a great brand but, sadly, I was terribly mistaken. Never again. Finally got someone to say they have to replace all the controls. They say they will send parts but I have to pay someone to change it out... sounds like they admit there is a problem but will not accept full responsibility for it. I did not make the item so why do I have to pay to have it fixed? I believe they should issue a recall and make all of us believers in them again. I guess its my fault for buying their product? So... doesnt clean, spin, rinse, lock and has a bad odor... not a great product, is it?

On March 3, I purchased a dishwasher (Model: KUDE70FXSS1 Serial No.: F10202361) on Whirlpools VIP link, which will more likely be my last Whirlpool purchase based on the slightly damaged product and incredibly poor customer service Ive received. Upon delivery of the dishwasher on March 9, I noticed that the left rear wheel was damaged and slightly bent. I also noticed that the unit was a little off balance. But the delivery person explained to me that everything was okay and that the front legs just needed to be adjusted. I believed him and signed the delivery receipts with the additional note about the left rear wheel being damaged. At the time of delivery, the driver also happened to mention that J.B. Hunt did offer installation services for dishwashers. I then called Whirlpool customer service, which pretty much gave me the cold shoulder, and said that it wasnt in their policy. I had to request the installation service at the time of purchase and Whirlpool would not send someone back out. This made me upset because I initially wanted to have the dishwasher installed but your VIP link didnt show an option for installation. Im not sure how Im supposed to request the installation services when theyre not being offered. But the genius customer service representative thought that I should intuitively call Whirlpool when the link isnt on the website. This is the first demonstration of Whirlpools poor customer service, in my opinion. After a couple of days of driving around to get a hose and a cord to perform the installation, I finally installed the dishwasher on March 12. Once installed, I noticed that the hinge on the left side was rubbing against the tub of the dishwasher. The door hinge was bent and the main tub was slightly damaged. Again, I contacted Whirlpools customer service department who sent out a repairman who confirmed that the dishwasher needed new tub and hinges which were covered under warranty. Unfortunately, he told me that I would not receive a new dishwasher since I installed it myself. He would order a new tub and hinges and transfer all the equipment and wiring from my original dishwasher to the new tub. Essentially, I would have a refurbished dishwasher at a new price, which I do not want.I initially wanted to have the dishwasher installed but your VIP link didnt show an option for installation. If Whirlpools website worked the way it should have and offered an installation service, I wouldnt be in this situation. I would have paid for the installation and the people installing the new dishwasher would have realized that it was damaged prior to them leaving and ordering a new dishwasher. I am a customer and not a dishwasher repairman. No normal person would have been able to catch the damage that is on my machine. Second, I find it hard to believe that Whirlpools policy states to have all the equipment from my original dishwasher installed on a new tub. So, I paid $989 for a new dishwasher thats really a refurbished dishwasher because of the damage. I wish I would have visited this site prior to purchasing. I will never deal with Whirlpool again.

Bought this front loader washer. It is unbelievable this thing will not wash a load properly. It refuses to spin at high speed because it is constantly out of balance even if you only have one or two garments and it keeps saying add more garments. As you keep adding garment its even worse literally. If you have anything that is heavy in this like a towel or a pair of pants or a hoodie or something like that for sure youre going to have to wash one thing at a time. I will never buy another one. I wish somebody would sue the living crap out of him for this piece of junk. I want my money back...

On 2-26-13 I received my new Whirlpool Refrigerator, Model WRF989SDAE, KSN 4191832, 28.6 cu ft, french door for a price of $2500.00. November 2014, refrigerator stopped working. Though it was not under warranty any longer, the repair company advised me that the problem was a warranty item and repaired it at no charge. This process took several hours of work by the repairman and two visits. He advised that this is an issue with the refrigerator and Whirlpool is aware. Now, May 2015, only 6 months later, ice is building up on the back wall of the freezer and the freezer is running constantly and very loud. Bringing in repair person, hopefully before it stops again. Appears to be related to the initial issue. I cannot trust this refrigerator and would highly advise everyone not to purchase a Whirlpool refrigerator. Refrigerator needs to be replaced, not repaired.

We purchased Whirlpool AquaLift oven from Lowes 10 months ago. Since then, I dread each time I use the oven because I end up cleaning it by scrubbing and using different products because AquaLift cleaning is a scam. I have arthritis in my joints especially my neck, so cleaning it by sticking my head inside is a nightmare for me. I will try to call the company and see what is going to happen. I read that someone is suing Whirlpool for this product so hopefully they will recall the product or refund us if we return it.

I bought a pair of Whirlpool front loading washing machine and dryer on May 23, 2011. The Duet Steam washer model is WFW9640XW, dryer is WED9470WW. Their high retail price was $1125 each. I did not pay this for them. I thought I got a great buy at Lowes for the price I paid, plus their 4-year extended warranty. Whirlpool used to be a very high-end appliance manufacturing company. Now, all they put out the back door is junk. I would advise not to buy Whirlpool front end anything. My washing machine started making noise about 2 weeks before I reported it to both Lowes and Whirlpool. The noise sounded like bearing not being lubricated, which that is what it ended up being.The noise got so loud that even with all my very expensive electronics (my home entertainment ctr equipment) I could not hear the TV which goes through an expensive Yamaha AV Receiver and those expensive Infinity speakers 7 channel system. The main bearing for the wash drum assembly was bad. After two emails and several phone calls to both Lowes and Whirlpool, Whirlpool was going to send the so-called re-engineered drum assembly. The style I have is 3 parts; the new one according to Whirlpool is one part, but if they put the same bearing in, youre going to end up with the same problem in another year. I live in a condo of just over 920 sq. ft. so really there is no room to repair them in my home, but that is what they are going to do. I will be getting the new drum assembly delivered to my condo and have the repair company doing this dirty job in the middle of my living room.Living in a condo, I have a small utility closet next to the kitchen where the furnace, hot water tank, and washer and dryer are. The closet needs to have some areas cut out with and installed two small hinged doors on each side, so if anything ever needs to be repaired or replaced, there would be a little bit more room to move items in or out. The problem getting the washer out is getting the dryer moved so you can disconnect the electrical plug, cold water hose for the steam, plus the vent hose. First, you have to get to the water valves which are very hard to reach. Because of the way cluster housing is made, they squeeze things into very small holes like the faucets and drain hose are located. I was asked by the repair person if I could help him lift these items out of the closet. I have had 7 fusion back operations and #7 left me in constant pain that I take a narcotic drug for pain daily. So, I called Whirlpool back and said the repair people were only going to send a tech. I was told that it is a two-man job: one tech and one helper. So Lowes needs to authorize two people since Whirlpool is sending the new drum assembly for free. I wish I could have gotten a new washing machine with the so-called re-engineered drum assembly. I am still probably going to have to squeeze between the bulkhead (wall) and the washer and dryer to disconnect everything since I am a small person. If I wasnt retired, I would have bought a different brand front loading washer and dryer, probably Bosch and took the loss on these piles of Junk. I love my country and do my very best even as hard as it is in this day and age to buy US. I served my country in the US Navy during the Vietnam War, just to see the civilians willfully buy Asian everything. So now, we have 4 Asian nations that own this country. I dont know why Whirlpool changed from a company that you could trust their products to a company that doesnt give a damn what they put out the back door. These companies still havent gotten the clue why folks buy goods from other countries. I think they need to open their eyes, but I guess with Whirlpool still being a company that is selling a very large number of appliances and making money off of us, suckers, they dont need to change. The only way they are going to change is if folks stop buying their junk.

Whirlpool Washer W10740628A - So disappointed! I have made adjustments for a year trying to get clean clothes from this machine. Compared to my previous machine which wore out, I now use more water because only deep water wash provides enough water; I always choose double rinse because if the machine does not clean, I do not trust it to rinse effectively either. I use more Tide than previously per wash; I use more Clorox than previously per wash. Everything from tea towels to heavily soiled jeans show stains and soils after washing. Instructions say not to spread the item in the washer but allow it to stack on itself, so twisted and tangled wet clothes are the result. I try to soak and scrub all visible dirt before I start the machine now; additionally, I use a mop or plunger or my hands to thoroughly immerse the clothes in the washer, somewhat like my mother did in 1950s. What on earth is this about and what is the buyer supposed to do???

Purchased a gas stove June 10th, three days later smelled gas. Called the store where I purchased item, they gave Whirlpool 800#. They set an appointment 2 weeks out. Got part then burners only clicked. They ordered more parts. Now top range works. Started to use oven and got extremely hot. Called store. They referred back to Whirlpool. After hour and half they scheduled appointment. First appointment he didnt have tools to check temperature. Rescheduled for following week. He said oven was off 30 degrees. I then went to store to ask to return item. They said up to Whirlpool. On phone with Whirlpool over two hours, them switching from one department to another. No help. They insist on fixing again tearing up unit in my new wood floors. Dont buy anything from them.

I like the looks with brushed stainless steel and black. The most difficulty was getting someone to help get it and load it. But other than that, Ive had no problems with the dishwasher.

I purchased Whirlpool gas range. After approximately 1 year, it has repeated problems with oven failing to maintain temperature. The unit would remain on, with the bake on still showing. But the temperature would decrease to the point of not cooking the food. If you turned the oven off and then back on, it would preheat again and resume baking, only to kick back off again later (again, with the bake still on).

Bought a Whirlpool Cabrio Washer Dryer combination on 4-5-2009, had it delivered on 4-20-2009, was very excited to get this set as it was like my first ever brand new washer dryer. I thought Id spend the money get something good and it would last for years and years. Was I ever wrong. I bought the set and the extended warranty from Lowes and my total with delivery was 2579.00. 20 days after the extended warranty expires (that I never used) the bearings on my Washer go bad. This thing in spin cycle sounds like a jet engine. I called to see if Lowes would still honor my warranty because I never used it and they said no. I called Whirlpool and checked to see if there was a recall and they said no. I checked to see if there is anything they could do at all because this is a huge known issue and of course they said no. (Just look on YouTube for Whirlpool bearing replacement and the amount of views should indicate the amount of troubled users.)Called a repair scheduled through Whirlpools website to come look at it for a 75 dollar assessment and they said it would be about 500-550 to replace the outer tub - largely due to the fact its labor intensive and the bearings are packed in the outer tub from the factory. I was like are you ** kidding me? I paid 1029 for the unit brand new in 2009 and 550 to fix? I said thank you to the repair guy and escorted him nicely out. Upon that I called back Whirlpool to tell them how displeased I am and how I will not be another product of theirs ever and mostly due to the fact they know this is a huge issue and wont do anything about it. I will be going to Lowes to see if the guy who sold me this pile of crap will work me a deal on another unit or set of another brand after I show him my receipt and express my displeasure with that product. If they wont do anything I will go to another store and spend my money elsewhere - I have choices and others do too. So if you are thinking about buying anything in the Cabrio line, dont. Go Samsung or LG - 10 year warranty straight from the manufacturer and costs 200-300 less than I paid for my washer dryer 5 years ago. The bearings are ** and shouldve lasted a lot longer for the amount I used this machine and for what I paid! Shame on you Whirlpool for using crappy parts to make your machines.

My Whirlpool dryer - Model# wgd49stbw, serial# ms2405113 went out on 1-29-16. Which I purchased from Lowes in August of 2015. Called the service company that I have my extended warranty with. They came out on 2-1-16. They did not have the part I needed in stock. It had to be ordered by the manufacturer. Sadly, I am still waiting and have been told it might come in on 3-29-16. Every time I call it gets pushed out another two weeks. This is really ridiculous. All the money I have spend at the laundromat I could have had a different source come out to fix. Which I still may do. I will never purchase another Whirlpool appliance again and certainly will NOT recommend. I am 65 years old and have a hard time dealing with the laundromat. If they get this part in by 3-29-16 it will have taken them two months. So sad.

Purchased a Whirlpool washer and dryer (WFW75HEFW0) in September 2017. Have had 4 service calls on washer for not completely washing clothes, leaving excess water after cycles complete, excessive wrinkling of clothes even on non wrinkle clothes, odor on some clothes due to incomplete water fill on some cycles. Factory position since there are no error codes washer is fine. Asked factory to exchange washer and upgrade model which we would pay difference. Denied. Looking for another brand and will seek legal assistance in the matter.

After 5 service calls for cooling problem, under extended warranty, refrigerator was replaced. Had purchased 3 water filters directly from Whirlpool before problem. Could not use these filters in replacement model. In spite of that fact & filters in unopened factory package, Whirlpool would not refund the $100 purchase price because I DID NOT RETURN THEM WITHIN 90 DAYS OF PURCHASE, even though I wrote to their US president. Really unfair treatment & they could care less that I had to replace a defective product.

My two-year old Whirlpool Duet Front Load washing machine is ripping my familys clothes. When I went online and saw all the other customers with the same issue, I contacted Whirlpool. Although the contact said that he knew I was frustrated, he could do nothing but send a repairman at a cost of $129 for me and then I would also have to pay for parts. I informed him that the online sites are saying that this is just a temporary fix. He pleaded ignorance and could offer me no other alternative. This is the last Whirlpool or Maytag product we will ever buy... and letting others know about the lack of cooperation.

We have had nothing but problems out of our refrigerator in the past 5 months. We purchased it a year ago in April and they have already replaced 7 parts on it. It still doesn’t freeze, and we have no ice... We will NEVER buy another Whirlpool product ever again!!!

In 2099, I purchased a Whirlpool Gold from Lowes. It has never cleaned my dishes, especially the pots and pans. My dishes also have a powder coating on them after various cleaning cycles that I have tried. I have tried every detergent available.The repairman suggested a detergent, which I already tried. He told me that the dishwasher uses only 1.9 gallons of water in total. That confirmed what I thought the problem was, not enough water! It is a design problem that cannot be fixed. I have bought Whirlpool for years but not in the future.

Purchased a Whirlpool Cabrio washing machine from Sears in August 2010. Last week, while my wife was washing clothes, we smelled smoke and the washing machine stopped working in mid cycle. Called Sears repair and came out Saturday 10/10/2015 to inspect the machine. When the repairman checked the codes he determined there was a problem with the motor. When he lifted the machine up the capacitor fell out in 2 pieces. It had blown apart and the motor had burned up. The estimated repair bill was $480.00. Needless to say we did not repair the machine. We will never buy another Whirlpool product or any other product that they manufacture under a different name.

Love love love my Whirlpool range!!! Regular bake and convection!!! Huge oven, beautiful glass top, and 2 burners that have double surfaces to fit huge pans! It has steam clean feature too!!! Incredible and amazing price!!!

I bought this Whirlpool America dishwasher because it was cheap. Even though Im Canadian, I like patriotism and I could get behind the American flag logo on the washer. Let me just say, if you like when food comes off your plates, and attaches to your cups, then this is the dishwasher for you. It is always a surprise when you open the door to discover which dishes have been cleaned, and which dishes have inherited the food particles from the now clean dishes. This appliance really helps you work on time management as you are required to wash all your dishes before you put them into the dishwasher. 0/10 would not recommend for anyone who wants clean dishes.

We purchased a new Cabrio top loading washer in June of 2011 to replace a Maytag Neptune (thinking at the time that wed gone as low as possible). We didnt abuse the machine. In fact, because it had a tempered glass lid (in a plastic frame), we were careful with the lid on the machine. It broke during a wash cycle. Because its heavy, the lid has spring supports on both sides; these are stronger than the plastic frame and over time the frame will break, rendering the machine inoperable. The discounted price for a new lid is over $200, and Maytag (I mean Whirlpool) tells us that it lasted through the 365 day warranty, so the bill is on us. It may be green when it works, but taking 18 month appliances to the landfill is not very green. And others on the web report say that the lid only lasts a year or so. The ratings scale needs to have negative values. Id give this appliance a -5.

I bought a Whirlpool french door refrigerator, model # ED5LVAXWS about five years ago. I didnt have any problems until last month, on August 25, 2016. The ice dispenser stopped working, and the refrigerator went off. I had to throw out a lot of food. I got a new extended warranty that day, and a serviceman came out the following day, 8/26. It turned out he wasnt a repairman, just someone to diagnosis the problem and order the parts. The part was ordered, and the fridge would be repaired within 5 days, but the part was delayed because of a Hurricane Hermine, which completely understandable.On 9/8 the repairman arrived, but he realized that the original guy who diagnosed the problem was in error. He had ordered a compressor, and what needed to be replaced was the thermostat. As of today, 9/29, the part is still not in -- I was told its on backorder with no ETA. If I didnt have a mini fridge, Id be at a complete loss. I called what I thought was Whirlpool to complain about the part taking so long to arrive, but was told they can do nothing. It turns out that a company called AIG U.S. Warranty Division handles Whirlpools guarantees. I am not a happy camper.

I bought my Whirlpool dishwasher, model #WDF560SAFMO in Nov 2016 with a 2 year extended warranty. In Jan. 2021 it quit working, was told by repairman that the dishwasher needed a new pump. Of course, it is no longer under warranty. To replace the pump will cost almost as much as a new dishwasher.

I’ve had my washer and dryer for a long time and it has been okay and it’s time to update. It has had its up and down and I may get another just after a while they are outdated and better appliances come along. Smarter people are making smarter things.

Purchased a Whirpool Cabrio washer. We bought this on sale at a Lowes and paid half the original price. Get it delivered and set up no issues. After about a week of washing clothes, there is a God awful smell coming from the washer because the water does not drain completely! I have used refresh washer cleaner to try and get it to go away. Most of the time there is no smell, but about once every other week, the smell is so bad it permeates through my home and makes it smell of rotten garbage. I do not recommend this washer. The cycle times jump around from the original time it tells you and the smell is just so bad. The little tray where you put liquid detergent doesnt even have a way to drain the detergent into the laundry properly and after every wash I have to dump the tray out because it stays filled with water where the water comes in and causes the detergent to rise out of the tiny hole on top. You might as well just add the detergent directly onto your clothes. I use an excellent brand of detergent that has top reviews and my clothes still dont come out smelling good from this washer. I have tried other detergents too to make sure it wasnt that one. I wish my hubby and I wouldve never paid for this thing and gone with a different one.

I bought a new home from DR Horton with Whirlpool appliances. All of the kitchen appliances were Whirlpool which came with a 1 year warranty. After closing on the house and getting in, started the dishwasher for the first time, it started leaking water instantly from the bottom of the unit and spilled all over the floor. Tried to contact the builder/inspector who asked us to contact Whirlpool. Called Whirlpool and I was kept on hold for over an hour before someone answered. The rep was so adamant talking all unrelated things and said that she cannot do anything for another 15 days. After escalating to the supervisor, it was the same response. The service at customer care is so bad with no fix in sight. I am not sure what they are going to do with the appliance and not sure whether they come and fix it or keep me waiting. Very unethical, the way they talk to the customers.

We purchased a Whirlpool AccuBake oven in 2005. I think we used the self-cleaning feature about 3 times. The reason I mention this is it may be a possible cause to the frightening experience we had on August 15, 2012. My wife was cooking on the stove top when suddenly we heard loud electrical explosions coming from the back of the oven. We soon saw long arcing bolts of sparks shooting out the back, and my wife was terrified and didnt know what to do. I told her and my son to stay away from it. I ran to the circuit breaker box and turned off the breaker. We then looked in the back of the oven and it was on fire. I ran around looking for a fire extinguisher but my son managed to put the fire out. We called Whirlpool up and explained what had happened. They immediately sent someone out to look at it.I was very impressed at how fast they got someone out there. Whirlpool sent two technicians to look at the damage. After they were done inspecting, they told my wife that the problem is loose connections on Whirlpools side and not the feed and it had a damaged control board and that this is the fault of Whirlpool. He was very polite to us and apologized for any inconvenience. After a week had passed, no one called us, so my wife called and talked to some woman representative at Whirlpool. She told my wife that the report she got said that the oven had loose connection on the feed side from where we bought the oven and we should deal with them. My wife couldnt believe her ears and said, No, thats not what the technician told us, and the woman continued to talk and my wife said, Wait, slow down. The woman replied, Oh, am I going too fast for you? Well, I guess I have to talk slower then, in a sarcastic tone. My wife then called the technician who wrote the report and explained what the representative had told her, and his reply was, I cant believe she said that. I am not happy about this, that is not what I wrote in my report. Dont worry, I will personally take care of this. Again, the technician was civil and polite. After two days passed, my wife talked to the same woman again but this time she changed her story. She never apologized and said, It looks like in this report that the connections were loose to the control board. Since the oven is 7 years old and accounting for depreciation, Whirlpool is offering to you a total of $59. My wife said, Really, $59? How long is the life expectancy of these ovens? She told her, 10 years. My wife said, 10 years? Well, ours only lasted 7 and you are giving us $59 after we were almost killed and my home could have burnt down to the ground? She said, That is our offer.I called Whirlpool back and asked to talk with the safety supervisor and it was a woman again. Was it the same woman? It could have been the same woman my wife talked to, I was not sure. I asked her, When is it appropriate to issue a recall on a product? Our oven was defective at purchase. She said, You are the only complaint we had on this oven, so no recall is necessary. Yes, I said, but since it has been proven this is the fault of Whirlpool, I would expect at least a working oven from Whirlpool. I also told her the technician told my wife that Whirlpool should be bending over backwards for you, and she said, I apologize for the technicians remarks. I told her that I was dissatisfied and she will be hearing from me in the future. I did some looking on the internet and I found that KitchenAid which is made from Whirlpool had issues with a particular oven which was found that when the self-cleaning feature was used, it would heat up the control board, and since most people dont use the self-cleaning feature that often, it would take a very long time to develop. I thought that loose connections and heat are a bad recipe for disaster, and that quality control negligence and inferior components are to blame. Considering the past history and track record of class action lawsuits and appliance malfunctions such as the control board on their dishwashers, I believe it is all connected and related to my problem. Sorry but $59 isnt going to buy me a decent toaster oven, let alone a real oven. That oven should have lasted over 10 years and considering the possible damage and deaths that could have occurred, you would think that it would be in Whirlpools best interest to address this problem and bend over backwards for anyone who had the misfortune of purchasing this mickey-moused nightmare of a disaster-waiting-to-happen problem. Its not so much the money. What if a small child touches an oven as it conducts 220 volts then shocks into a childs heart to ground? What a ticking time bomb this oven is. As far as I am concerned, I dont want a dangerous oven like this in my home and Whirlpool needs to take some lessons in public relations.

Glad to know we are not alone in our disappointment with our Whirlpool French door refrigerator, but I am wondering what and when Whirlpool is going to do something about this. What a blow to their reputation. Goes to show things are not made as they used to be. We purchased our Whirlpool Gold French door (bottom freezer) in August of 2010. Here we are October 2012 and this is the third time it has stopped working. We have lost food, weekends waiting for repair people and cleaning up messes, and money. Same problem as others are reporting - the electronic board and controls. I just spent my Friday evening on the phone with Whirlpool, first explaining the problem to no result then waiting for a manager to call me back. Who (guess what?) never called. I finally called them and got the same script as the rest of you. It is outside the manufacturer warranty. Really, that is what you are giving me? Plus they will only look at it if we have a Whirlpool repair person come see it. When can they come? In 4 days! Ha, not likely. I am not giving this company another cent. We spent almost $2,000 on this fridge, all we are getting is 2, 3, 5 years? What a shame. We are fortunate enough to have had some space in our garage beer fridge for what I can save of the food. Our 7 years old, $300 Moffat fridge has been working like a charm. We will never again fall for the looks of a Whirlpool, let alone purchase another one of their appliances.

Weve been in this house for almost 4 years so the dishwasher (Whirlpool WDT790SAYM) is no older than that, maybe even 2.5 since I think I got it home in my CX-5 which is 2.5 years old. Anyway, never really had a problem with it and we run ours maybe once a day or twice in a row every 3 days. Last night I remember running a load and this morning noticed the dishes were dirty but the inside of the tub looked clean. So I plop another pod in and tried to run it again and sat there and watched it. It filled up with water but then nothing. After 20 minutes I opened the door and steam came out so the heater element was working and there was water at the bottom. I tried various things but nothing. Canceling still works.So either I try to get this fixed, or buy a new one. This wasnt a cheap dishwasher either. My wife balked when I 1st bought it considering she thinks a $300 model is better than most of these $500+ models. Right now I cant argue with her since we just replaced an expensive Samsung washing machine that lasted maybe 5 years. Theres another review of this model on these forums and the person tried to get it repaired many times and it appears maybe the same thing is happening to us. I wont go down that road considering repairs like that exceed the cost of a new dishwasher.

I have a front load Whirlpool Washer and it has leaked within 6 months of having it. The rubber piece was replaced and it still leaked. Whirlpool wont take responsibility for its product. I have to put towels down around the washer every time I use it because it leaks. I purchased this because it is more economical to use a front load but not when water is leaking from the washer.

Got the dreaded 4 flashes LED status - High Temperature Shutdown. Online and vendor documentation says that this condition requires gas valve unit replacement, a $115 option. If your Pilot remains burning, but main burner does not kick in, then a good guess is the circuit board requires a reset. Prior to any further work, test the Thermopile, that is the round item with two blades located below and to the right of the gas valve unit. Move knob on control panel to OFF1) Pull out plug with red and white wires located on front of gas control. 2) Have someone Hold in the control knob on the unit at Pilot, and make sure Pilot flame is burning. 3) Using a multi-meter, set it to millivolt reading, and test voltage across the two wires. Voltage should be greater than 350mV, preferably >500mV. 4) If you get a reading in that range, your Thermopile is good. Turn knob to off position. Do NOT uncouple gas lines. 5) Piezo Igniter wire comes apart, disconnect it. 6) Remove screw that holds front cover. (screw located bottom left as you look at the unit) 7)Cover simply pulls off directly towards you. 8)Remove the screw holding the circuit board to the cover, and remove circuit board by unclipping it - 3 clips, one either side and one at bottom. 9) Unplug the 3 strand thermostat cable, you should now have the circuit board clear. 10) Take a piece of aluminum foil, fold it twice, then lay circuit board on it facing up, do it on top of tank, want it grounded. 11)Using one of the multimeter probes, wrap a piece of foil around it, keeping point free, and ground it too. Then slowly work around the board, touching all the solder connections you see, as well as the chip legs. Pay particular attention to the round objects on the board (capacitors), make sure to ground out each of the solder points, visible either side. (takes about 5- 8 minutes, take your time) 12) Once done, reconnect thermostat cable to board, then reinstall board into cover (dont forget the screw)13) Place cover back into place, screw in cover screw, reattach Piezo wire and black electrical plug with thermopile wires. 14) set Knob to Pilot, get pilot lit (may take a few hits on the Piezo button) and while still holding the knob in, watch to see what LED flashes you get (there will be a 10 second time lapse before it will start to flash) 15) You should either get 1 flash or 7 flashes, that means the board is reset, now turn knob to warm, and see if main burner kicks in. Good luck, and for a half hours work you have saved yourself $$$. PS: If it occurs again, you have sediment build up, need to drain the tank.

I purchased a Whirlpool stove, microwave and fridge in November 2012. The fridge model #WRT771RWYB01 has been a lemon from day 1. I have had the repairman out for the same issues multiple times. Ice build up in the freezer, water tube to the ice maker frozen, food in the fridge freezing, blah, blah. They have taped, glued, replaced everything they can and to no avail. It still happens. When you call for service, it takes 2 weeks or better to get someone out. I will NEVER buy another Whirlpool product! This has truly been a nightmare experience!

Whirlpool Cabrio Model WTW6500 - I ask all of you to stay away from the Whirlpool Cabrio sets. I have spent hundreds of dollars trying to fix my washer. I just spent $260 for a computer board. Now it stays on rinse cycle. So now I need the motor sensor harness which is another $90. Service call $80 x 2. So, now I am going to take the computer board back and get my 260 dollars back. For the cost of $400 to fix this washer. You can go and buy a new one for around $400. Then, Im going to the lawyers to file a class action suit against Whirlpool. So, owners; be looking in your mailboxes for a class action suit against Whirlpool for those who own the cabrio set. Im tired of having to deal with whirlpool customer service. Maybe, whirlpool should think of having their laundry made back in America.

We purchase the Whirlpool Gold Dishwasher GU2400XTPB7 with our new home. This dishwasher has a plastic tub. For some unknown reason the dishwasher started to leak, I checked every hose connection and could not find the leak until I noticed four small burn marks in the plastic tub underneath the heating element. It actually looks like someone took a cigarette to the plastic. One of the burns went through the plastic tub, and this is where the leak is. Note: at no time did any of our dishes touch the heating element.I called Whirlpool customer service and they said they would send a technician out for $81 and in addition I would be charged $19 for every 15 minutes of service. I had asked to speak to a supervisor and he recommended that a technician come to my house at my expense and all the supervisor could say was that he was sorry, which became even more frustrating. No remuneration was offered. I have had other issues with our Whirlpool washing machine (holes in clothes), gas range stove (ignitron issues), and fridge. l will never purchase any Whirlpool product again including Jenn-Air. I made this quite clear to the supervisor. Whirlpools products and customer service are inferior based on my experience with our four appliances. It would be great if they actually practiced what their mission statement suggests, because as a customer I truly feel defeated.

Before a year was up after purchasing 4 Whirlpool appliances for our kitchen, our refrigerator needed a new compressor. Of course, they covered the cost because it wasnt a year old yet. After much complaining, they gave me a whopping extra 3 months coverage, until Jan. 2014. Now we have water leaking on the floor and ice collecting on the bottom of the freezer drawer. What a piece of junk! I had sent an e-mail to Whirlpool after the compressor situation telling them that I would never buy from them again and would have nothing good to say about them. No one responded. Goes to show that Whirlpool could care less about their customers satisfaction. Never again will I buy anything Whirlpool makes. By the way, our old frig is in our mud room working absolutely fine.

I have enjoyed my stove for 16 yrs, it is very reliable and easy to use. The heating elements work well and heats up quickly. During this time I have not had any repair done. The areas of improvement that needs to be implemented is the inter glass that is installed at the front looking into the oven. In order to clean you have to take the front door off which is very difficult to put back together.

This product is unsafe and should be recalled. It has aluminium wires that connect the unit to the 220 Vol Power source. Aluminium and copper wire dont mix. I took a shower and was getting ready to leave for the day when I went into my garage to smell burning plastic and wires. I traced it to the hot water heater and discovered the wires in the Energy Smart were melted and burned. I checked with Two Electricians who told me that the wires in the unit can not handle the high heat and melt. If you have one get rid of it. Had I left for the day I would have lost my home, cars and pets. If anyone would like to see this unit I still have it and photos.

I bought a new Whirlpool gas hot water 40 gal tank from Lowes. I Installed it, but the pilot light would not light. So Cal Gas Co came out and said they did not like the new design, but that was how they were now making them. Gas is shot out from a pipe into the tank, however its fairly open. The pilot ignitor is similar to the one on barbarques that often do not last. You cannot get to it to light it manually. Several calls were made to Whirlpool and they sent a repair man out to fix it. You can imagine buying a new hot water heater and having it work part time. The repair man explained that the unit needed a new thermopile, but he could not put one on until whirlpool authorized it, which they would not. After a rather heated conversation with whirlpool they agreed to FedEx a part overnight. Of course the repairman could not wait for me to call and had to come back again. The pilot light still does not stay lit, and Whirlpool now wants to talk about how the tank is vented. This has nothing to do with the pilot light, nor did putting in a new 1/2 gas line and valve as per Whirlpools request. Whirlpool has a problem and they refuse to acknowledge it. However, it is Lowes that chose to buy from whirlpool and they do little if anything to stand behind their product and gain consumer confidence. My suggestion would be dont buy whirlpool, and shop at Home Depot.

The machine has an infinite water level setting, an agitator which I feel cleans clothes better, separate settings for water temperature for both wash and rinse cycles, and the ability to soak prior to washing by just leaving the lid up. You can add bleach and fabric softener to dispensers that will add to the tub at the time needed. My machine has been a really good one.

Whirlpool Range Model XFE381LVS - 12/13/2014 4:30PM Wife was cooking dinner and turned oven on. Smoke started coming out of the back and called me. I ran to the breaker panel and turned off the breaker. Back to the stove, pulled it out and smoke still coming out in back at the top. I could see fire in the top of the back panel. Slowly the fire went out. Unplugged the stove, I removed the back panel, wires were still smoldering and the Control panel was burned thru. Took pictures so I could contact Whirlpool Monday. The Electrical control panel is destroyed as well as many wires. Glad we were home and oven was not left on while we were out in the yard or Home could have been destroyed. Purchased the stove from Lowes 11/02/2010 with a extended warranty. Tried to add receipt but would not accept, wrong type doc.

Whirlpool Cabrio drain problem - I never had a washing machine that lets so much through to the drain pump. I replaced pump three times already. First of all, if you put anything with buttons in this machine, you can kiss it goodbye. This machine destroys clothes then lets buttons and coins and whatever through to destroy the fins on the discharge pump. When is the BBB going to do something about this consumer ripoff?

Both are Whirlpool Commercial quality. I got them free from my Co-Op. They didnt cost me anything. They have been here for years - at least 18 years. They have performed flawlessly. I would look for anything discounted. I do not have a problem buying scratch and dent items or last years models. I am not big into brand names and their claims. My sister has gone thru several Maytag appliances in just a few short years. I will not buy any front loading washer, its top load only for me. The dryer has to be electric because we do not have gas in my Co-Op complex. I have been lucky to have only two washer and dryer combos since I was a kid. My family bought a Kenmore washer dryer combo in the 70s that lasted maintenance free into the 90s when I got the Whirlpool set that I have now. I only need the basics side by side set ups. Even though I live alone I do a lot of laundry. Since I have had these commercial grade machines I am more leaning toward another set of commercial grade machines. They seem to be able to take more abuse/over loading than the fancy expensive machines.

Whirlpool Cabrio Purchased 12-7-2012 - what a piece of junk. Does not get clothes clean, rarely does she even spin out properly. Called because it kept walking across the basement floor. Informed that was the owners responsibility, not the store (Feidens in Latham). Always had good luck with them, bought all my appliances from them. Now I heard a loud bang and she threw up - water everywhere. What a mess.Had purchased special patio block at Home Depot to even her out and every time I used it which was not too often, it acted like the space shuttle ready to head down the runway! Not too happy with Feidens attitude with regard to this purchase. Not going to call them to fix it. Not an ready to pay to listen to their guff again. Expensive machine never worked well since it got here. I always wished for a Whirlpool, be careful what you wish for! Junk, nothing but junk. Only 3 years old and I only do laundry about every 3 or 4 weeks. Live alone, so she certainly was not overworked.

As a rule, everything I put in it comes out spotless, but I know it is more a function of the detergent than the washer itself. Has nice features but the digital system does not allow you to turn a knob and go to a particular function like the older one, I miss that. Its a standard under the counter dishwasher, plain white with a nice, attractive operating panel with small LED indicators. NEVER put any vinyl, 45 or 78 record into a dishwasher!!! It will dissolve the labels, and if its made of acetate (home recordings) it will destroy it.

First one had major problems. The bladder they call it. They took out the whole system out, replaced the tube that goes to the top of the refrigerator which is where it always starts leaking so they worked on it three times, junked it, gave me a new one and here I am again same thing. Ruined my hardwood floor and Im stuck with it. Never again will I buy WHIRLPOOL.

2013 Whirlpool gold series stainless steel dishwasher, at that time it was their top of the line product, nice looking, stainless steel, stainless steel tub, very quiet. However this piece of junk does not stay fixed for more than a year, at best. I am a technician by trade albeit not on consumer appliances, I usually work on more complex multimillion dollar equipment; point being, I know my stuff.I have been throwing parts on this box like no tomorrow, Tub replaced, water director motor replaced, top railing replaced, small plastic pieces on top rack replaced. MTBF - Mean time before failure is 6-8 months and deteriorating over time. 2 issues are predominant symptoms of its failures, its either leaking or dishes dont get cleaned. I see the symptoms again and I am tired of fixing it so it going to the curb tomorrow. There is no way an expensive appliance like this (around 800$) can cost 100$ a year in parts to maintain (Note: parts only)... not to mind my labor and hassle ++ water damage to your cabinets. Stay away from Whirlpool and keep your sanity!

My new Washing machine was to be energy efficient. Yes, It uses less water to wash a load of clothes. Problem is, it takes twice as long to wash a load of clothes as older models. If it uses twice as much electricity, In what universe can this be considered energy efficient?

I have the Cabrio model WTW6400SW2. I have had it for 5 1/2 years and have been happy with it up until several months ago. The F1 would come up when the machine would lock and just start to fill. I could pause it and start it again, and it might do this 1 to 3 times. It would also do it on the rinse cycle. I have been using it because I did not want a repair bill right now. The machine was also starting to make noise when it was spinning. Well, I just happened to break my dryer yesterday so I thought I would get the washer fixed also. Well, the repairman said that the controller would cost $200 for the part, and then he said the pump roller and bearings were going. By the time you add on labor, he said, “You might want to buy a new one.” He told me that Whirlpool has completely changed the washer now because of all the problems with them. He told me to look it up on the computer, and maybe there would be a class action suit. After reading some of the reviews, I will not buy another Whirlpool again.

My wife and I purchased our Whirlpool Duet Model # WFW95HEDC 7/19/16. I put my first claim in on 12/19/16. We were sitting downstairs one night watching tv and all of a sudden a noise like the sound of a tractor trailer putting on its jake brake came roaring from upstairs. It was so loud that we both jumped. The machine would periodically vibrate violently while going thru its spin cycle. The frequency started to get closer and closer together. Whirlpool had a technician come to our home. They came out 3 times and said that nothing was wrong. They said that it was vibrating because it was on a pedestal and upstairs on a non solid floor. They also blamed the loose water hose on the noise. SERIOUSLY??? After the 3rd visit, and a week before the 4th visit our machine started to leak. We paid $1,079.00 for this washer and we were having to take our laundry to a laundromat to wash it. The technician came out the 4th time and replaced a cracked drum. Apparently it vibrated so badly that the drum cracked. So everything seemed ok, then WHALAH!!! We wash the clothes and go to move it to the dryer and it is dripping wet. Somehow after they replaced the drum the machine started to not spin the water from the clothes very well. Takes drying the clothes for 50min 2x to get them dry. I am now set to have the appliance company come out for a 5th time and still not corrected. Whats worse is that every time I contact Whirlpool they give me the same canned speech and want to set up another appointment with the appliance company. I am soon at the year mark with my manufacturers warranty and still having issues. I think Whirlpool keeps kicking the can down the road without making good on correcting the issue so they can get past the year mark and make us take it up with Home Depot on our extended service plan. I feel bad for everyone out there who got screwed by this company.

We have owned our side-by-side model # ED5HVEXVB02 for just over six years now. The first thing that went bad was the ice machine (just days out of warranty). Over the next 4 years weve had to replace 2 of the drawers; they break really easily. Here we are just 6 years out and we are on our 3rd icemaker. This refrigerator is a lemon. I sincerely believe they designed an inferior product so that they could get you hooked. We probably would have been better off after the first issue if we had sold this lemon instead of spending all of this money and future money that it will take to keep this product going.

I purchased a new Whirlpool stainless steel French door refrigerator MSRP for $2,500 in good faith. If something were to go wrong with the appliance, Whirlpool would fix the unit as applicable under their accompanying written Whirlpool Corporation Major Appliance Warranty for the duration of one (1) year from date of purchase. However, this has not turned out to be the case at all. As per their written Whirlpool Corporation Major Appliance Warranty for one (1) year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation will pay for factory specified parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased. Service must be provided by a Whirlpool designated service company.My refrigerator was purchased on 10/27 and delivered on 10/28. Service repair performed by a Whirlpool designated service company was on 11/30, 12/30, 1/9, 1/18, 2/9, and 2/23. A future appointment was scheduled for 3/22. Whirlpool’s designated service company notes from 2/9 specifically state that the refrigerator will not run and parts were ordered. Whirlpool’s designated service company returned on 2/23 for parts installation and noticed that other components of the appliance were not functioning properly and proceeded to call the tech line for support. After hours of troubleshooting and multiple failures to function properly, the service company deemed the refrigerator as un-repairable and clearly stated in their notes that the unit was not cooling, there is a manufacturing defect, restriction in the units seal system, and the unit needs to be replaced. I was instructed that the tech line would complete the ticket, send the information over to Whirlpool Corporation, and I would need to follow up with Whirlpool’s customer service to set up the delivery of a replacement and haul away of the non-working defective refrigerator.Furthermore, the company (manager Wanda at the TN office), had already promised to replace this unit if the service repair performed on 12/30 did not fix the unit, which the company has never honored and has since decided to recuse themselves of this promise made on behalf of their employee. In addition, this Whirlpool manger (Wanda at the TN office) even gave me her direct phone number and extension to follow up with her. She has never answered any of my 10 phone calls over a period of 3 weeks and never attempted to return a single voicemail that I left for her. Since the promise of a replacement refrigerator, I contacted Whirlpool by phone on the following dates: 12/30, 1/3 and 1/16; 1/17, 1/19, and 1/30; 2/20, 2/24, and 2/28; 3/2, 3/9, and 3/13; and 3/15, 3/16, and 3/19. I as well have emailed them information they have requested on 2/20, 2/24, and 2/28.Below is verbatim of the last few Whirlpool customer service representatives that I have had correspondences with.2/28 (Tabitha): I have sent in your information for the PEX (replacement unit) since I see here that your unit is un-repairable. Someone will continue to contact you within 24 to 48 hours to go over the PEX process with you.3/2 (Brittany): I see we received your file on March 1st; however, it was denied because the request was blank. Can I place you on hold on a moment? (After a long pause) I apologize for leaving you on hold so long. Your records were listed under two different accounts on our end with one being linked by your phone number and another being linked by your address; therefore, all of your records have probably not been viewable. Upon further review of your information, our Whirlpool designated service company that performed service on 2/23 will have to call into the tech line to complete their notes before we can proceed. No, you cannot speak to a manager. If you wish to have a manager contact you, one will do so within 24-48 hours. You cannot speak to a manager because at this time there is nothing they can do to assist you; unfortunately, this process is moving along at its fastest place and there is nothing more we can do for you at the moment. There is nothing that we can accept from you to speed this process along, even though your copy of the service company’s receipts include the statements of work from our designated service company. If you wish to escalate this matter, you can write to Whirlpool Customer Relations Department at 553 Denson Road.3/9 (Kia, supervisor): Although our designated service company may deem your unit un-repairable, Whirlpool has to deem your unit un-repairable for a replacement to be issued. At this time, Whirlpool does not deem your unit un-repairable. You will need to contact our designated service company and have them forward over your information. I am the highest level of supervision for the company and if you wish to escalate this, you can write to Whirlpool Customer Relations Department. Their mailing address was already provided to you previously. At this point, our conversation is over. We will not be replacing the product as we do not determine it to be un-repairable. Thank you for calling Whirlpool. The information we have discussed will be documented. I am the highest level of management for the company, so your request to be transferred to management is denied. I am aware of everything you have said and I have documented this information. At this time, I am done discussing this with you and will now hang up the line.This kind of customer service is not only discourteous, but it is despicable in the upmost matter. This displays complete corruption in regards to the written warranties provided by Whirlpool Corporation that come with your Whirlpool product at the time of purchase. Currently as it stands on 3/20, my $2,500 valued Whirlpool refrigerator is just under (5) months of the purchase date and has been deemed as having a significant manufacturing defect, as well as needing replacement by Whirlpool’s designated service company that they hold a contract with. Yet, Whirlpool refuses to replace the unit and refuses to speak with me based on the ground that only their contractactually designated service company deems the refrigerator as un-repairable, but they do not. My refrigerator has not worked in weeks!From reading the Whirlpool appliance product reviews online, I discovered that I am by far not the only consumer that has suffered from victimization on behalf of Whirlpool Corporation. I saw numerous consumers who had purchased the exact same product (matching model number) as me, had issues, and Whirlpool refused to assist them. Therefore, I think that we as consumers need to take a stance to stop these unethical practices of Whirlpool Corporation and demand that they honor their written warranty for their products. This company’s abuse and neglect of their consumers is absurd.

We purchased 3 Whirlpool Gold appliances, fridge, range and over-the-range microwave in 4/2011. Since that time, the fridge needed repair, the microwave door had to be replaced and the range had to be repaired. Now the heating element on the microwave went and Whirlpool will not fix the problem. We purchased the extended warranty through Whirlpool and they are saying it is not worth fixing. We paid $470.00 plus tax and install and now all they are giving us is $348.00. Since we have had repeated problems with these appliances, why not just fix the problem or replace the microwave??? What Whirlpool customer service told me was that would be options for us if we did not purchase their extended warranty. Tell me, is that fair? The cost to repair the microwave was $388.00 and they are giving us $348.00 - do you not think for the $40.00 difference, it would be worth to spend it to keep us happy. We will never purchase another Whirlpool product again and will tell everyone we know not to buy their products.

During the initial warranty the oven was not heating properly. Several service calls within the warranty issue was not resolved. Whirlpool extended the warranty another year as of this date and several service calls problem not resolved. When a tech comes out there is a diagnostic check that checks the temp for 10 min. Since the temp drops after 10 min they cannot detect problem. I asked for the tech to remain for the complete cooking period which they cannot do. I have wasted many meals and still have a oven that does not work.

I just purchased a brand new home. I have an electric wall oven with the microwave over the oven. They are both built into the wall. Can anyone tell me why a massive amount of steam is coming out. It is really bad it makes my microwave glass so bad I can see through it. It is also making my cabinets so wet I have to use a towel to dry them. Plus I got a steam burn. Can someone tell me if this is normal.

We bought Whirlpool Frontloader Washing Machine not over 1 month ago and it started to malfunction showing Ed1 error on its display. We contacted the service center and it was taking too long to have a visit from a technician. Then the technician, who also installed the unit came and checked the unit. He called someone from corporate office or from support team to ask what is error code Ed1 and overheard over the phone that this is a known issue on the brand. The technician said it is possible that unit will be replaced or only the motor. I contacted the brand support thru Messenger and requested to have the unit replaced, because again, the unit is not over 1mo old.I was advised it is not possible as replacement of unit is only applicable when the issue happened within seven days of delivery. STUPID ISNT? Policy is something unworthy for a product that is over 30k. And again, unit started to malfunction not over a month after it was first used. I would say we pretty much took care of the unit, we only use it twice a week. Placed it where it was perfect to put. Followed every advice given to us by the technician who installed it but still, it malfunctioned a few weeks after we started to use it. I am ashamed of the brand itself, we should have chosen Panasonic or Samsung instead not a dumb brand like Whirlpool. I certainly do not recommend the brand for a washing machine unit. Frontloader is a crap.

Rust started forming early on our washer and spread quickly. Our house is air conditioned and not near the ocean. There was no reason for the rust. Poor quality finishing is the only explanation. When I called to complain I got nowhere. I wish I could show a photo on this website. It would dissuade anyone from ever buying a whirlpool.

Bought new Whirlpool duet washer 4.0 couple years ago. Started making load noise. Started checking and its the rear bearing and sounds of it will cost more to replace than to buy a new one. Found this page and after reading review after review, I will not spend a dime to fix the junk product from Whirlpool. Going to put in the dumpster and never buy another Whirlpool product. I have never seen so many complaints about a product and many being the same bearing problem. Where is our recall process? Its ok to rip off people over and over with no consequence. And why do large chains keep their product? Guess theyre in on the rip off.

I cant believe the list of people here with poor quality of their washing Machine. My first problem was covered under warranty. I have paid for two service visits from A&E and now every 5 minutes get the LF error. My fabric softener does not drain into load either. My only option is repair again and I got a sorry from Whirlpool. I think Im going to look for an old fashion cheap machine as it cant be of worse quality than this Cabrio wtw6400sw1.

I purchased a water heater in 2011 and have had the thermostat replaced at least 5 times! Now, not only does the heater not heat the water, but it has rusted through and ruined my floors! They say they will replace the thermostat (oh yeah, yet another one!) but what about the crappy thing in the closet. I will NEVER buy anything that says Whirlpool on it. They dont stand behind their product and have made no efforts to correct the issue. There has to be a lemon law clause that would be applicable in here somewhere.

I purchased new appliances almost 1year ago to the date. I bought the glass top range with. convection oven. In convection mode, the fan cuts on and off intermittently during bake cycle. Friends who also have the same oven say their fan runs consistently in convection mode. Repairman came out and changed fan and control panel. Still runs intermittently. Apparently that is a feature of “some models”. Had I known it was not continuous convection, I would have purchased a less expensive model without convection feature. It takes longer to cook in that mode.

Best stainless steel built dishwasher we could find in this price range. Well built with lots of room and easy access to both drawers. Easy to clean filters and a nice modern look.

My comments are similar to all the other comments on here regarding the Whirlpool Cabrio washer: I bought a Whirlpool Cabrio 5 years ago and have been sorry every wash day since. I have to wash my clothes twice because the machine doesnt fill the tub with enough water to get the clothes clean. I have tried using the bulky setting for all loads to try to get the water level high enough to at least cover the clothes. This is a terrible design and the worst piece of junk. I will never buy a Whirlpool product again...