Efficient. I like the look and the controls. I trust the Whirlpool brand, but have purchased other brands. This is probably the best dishwasher I have owned. My only regret is that it is louder than expected.

We purchased our Whirlpool dishwasher/Model no. WDT780SAEM in July 2016 and it was installed on August 3, 2016. Right away we noticed 2 problems. The top tray squeaks very loudly when being pulled out for loading and unloading. The usual temporary fix for this would be using a product like WD-40. Of course as soon as you run the dishwasher all of the product is washed away. This was our first complaint about this dishwasher. The more important problem was the white cloudy residue being left on all of our clear plastic cups and glasses. Weve always had hard water but our previous dishwashers were able to remove the residue if we used the high-temperature wash. After looking at all of the manuals and user guides that are included with the purchase we read that we should be using a rinse agent and a product such as Lemi Shine to deal with hard water deposits. We tried these items and nothing worked.Using the All Fresh tabs didnt help and our filter was clear and clean. So we made an appointment to have the Whirlpool factory serviceman come out to look into our problems. First of all the customer service representative I spoke with was rude and impatient. She kept cutting me off and asking me about hard water and suggesting that I use all of the products mentioned above before finding out that I already had used them to no avail. Because we had the dishwasher for just over 30 days I asked her about the Clean and Quiet Guarantee that I found out about by going to Whirlpools site. Her exact words were The clean and quiet what?? So I didnt have much hope for our service appointment. Our serviceman was asking all of the same questions about hard water and if we had tried all of the products I mentioned above.After his visit we found out and now (too late) know that because our new dishwasher does not have a heat booster or the ability to get the water temperature high enough to remove the hard water residue theres nothing Whirlpool will do for us. This is the case with all newer technology dishwashers UNLESS you purchase one with a heat booster. I sure wish this wouldve been made clear to us, the consumer before making our purchase. If we had known beforehand that new dishwashers no longer get the water up to 140 degrees which is what would be needed to remove the residue, we wouldve made sure our model included a heat booster. Now were stuck handwashing our plastic items if we want clear dishes. Its not the end of the world but its not good customer service or honest to the consumer in any way, shape or form.

I bought on 14/4/12 a Model-205 Orchid Wine refrigerator. The defrost knob was replaced by service last month, as it was not working. For the past four days, there are lots of water formation on the freezer door and vegetables are getting spoiled due to water formation. I request them to replace the refrigerator.

Our ice maker was not producing ice. Whirlpool Warranty sent a co. Kens Appliance Services to our home. The repairman diagnosed freon leak. When he came back on Oct. 7 with parts he blowtorched the electronic board & wires while fridge was plugged in. We still dont have refrigerator weeks later. We are buying food & ice every day. The next co. they sent werent licensed to add freon. He verified burnt board. Third company they sent told Whirlpool warranty to replace our fridge. They tried to sell our warranty back instead.

I bought two Whirlpool (Model: bfg1j4o4t3nov4o) natural gas water heaters. The pilot light would go out to so I re-lit it and sit in the attic until the water got hot and the burner go out. But before the burner went out, I could see the flame go from blue to yellow and hear the water dripping down on the burner. So, after the burner goes out, the water would drip down on the pilot light putting it out.They sent me a thermo coupling for free but that was never the problem. The problem is that the water heaters are poorly insulated which causes the water to drip down on the pilot, putting it out. To make a long story short, no part they send will fix these heaters. I have a GE heater in my house for 20 plus years and it is still kicking. I should have went back with that same heater.For some good news, I got my money back from Lowes. I raised so much hell in that store that the manger gave me my money back just to get me out of his store. I made them realize that all we want is our hard-earned money back from a product that does not work.

I purchased a Whirlpool fridge brand new. Not even a freaking yr old it went out!!!! Repairman came out and said it had leaked crap all over really. He said it would be too much to repair. Better off on purchasing a new one.

I have had my Cabrio for a year now and quite frankly, I find more satisfaction taking all of my laundry to a local laundromat. There is no soak cycle and when you have a kid in sports, that doesnt help. There is no agitator, and I am now convinced that they were originally in all washers for a reason. My clothes have all worn out and are shredding, not to mention my very expensive bath towels that I am now cutting into rags. This was the worst purchase I have ever made in my life and will never even look at a Whirlpool again. When I bought my house, I had a Maytag that was 35 years old and it did a better job than the new Cabrio. Should have stuck with that brand!

I called customer service because my pilot light would not stay lit on my 2005 Whirlpool water heater. I was told that I needed to install the upgrade kit and that the water heater was malfunctioning because of a lack of air and that it needed to be cleaned at the bottom. I paid for the shipping of the kit although I believe it is called an upgrade or conversion kit versus a recall for this water heater to save money and to get the consumer to pay for replacing defective parts. A certified technician installed the kit but the pilot light would not remain lit. He replaced the thermocouple, although new parts had just been received. This did not help either. The technician and I called customer service, which didnt resolve the issue. I also asked for a manager who would only agree to send out another conversion kit. There are three years remaining on the warranty but I am being told to keep replacing new parts with new parts until it works. That is unacceptable. Also, I was not informed that my problem is a recurring problem with this Whirlpool water heater that I purchased at Lowes.

I love the brand. I just do not care for the lock lid on all the new washers. I could do without it. I do not have kids to worry about getting hurt. Im looking into finding a brand without a lock lid. I just replaced one before this one. For the lid breaking.

Our dishwasher stopped working after 13 months. We are a family of 2 and use it once a week. We called Whirlpool and were told since it is past 12 months, they would do nothing but give us the name of a repairman in the area. We called our own repairman and $120 later, the sensor that had malfunctioned was replaced. Quite costly on a $450 dishwasher. Now, after 15 months, the handle on the lower broiler portion of my Range has come off and the screws will not hold because the plastic around them deteriorated. I just called customer service once again, knowing what I would be told and YES was told So sorry, nothing we can do. A new handle will be $45 plus shipping. We bought the refrigerator at that same time and every day, I wait for this appliance to have issues. In summary, Whirlpool/Maytag appliances are obviously made to be disposable after 12 months. They do not stand behind their products and I would not recommend them to anyone.

I have Whirlpool 40 gallon heater 5 years ago. The pilot light went out and I replaced the parts. This has happened three times and I have replaced the entire thermocouple assembly three times. The last time, the parts came straight from Whirlpool. This time, the pilot light will not stay lit. I am on my way to buy another hot water heater for my family because I have had enough.

I have a Whirlpool dishwasher for a few years, it cleans great, works great, the dishes come out clean and shiny, so do the glassware. Even pots come out nice and clean, what more can you ask for?

We purchased an electric range model WFE371LVQ O in June 2010. This range is only used during the winter months in our vacation home. In January 2016 the oven turned on by itself. The control panel was replace. It happened again on 1/25/19. IT IS A FIRE HAZARD!! Thankfully we were home both times. The only way we got it to turn off was to flip the circuit breaker. If this would have happened when we werent home and a fire started and it killed our dogs I have no idea what I would do. Im not even attempting to have the control panel replaced again. Well be buying another brand. I DO NOT RECOMMEND THIS TO ANYONE. The company must have known about the issue because when we called the first time it happened, which was several years PAST the warranty period, they didnt hesitate to do the repair free of charge.

Whirlpool French Door Plus 3 drawers: This MSRP $3400 refrigerator has great features. Great ice makers. No issues up top. First 18 months were great. 4 repairs in the past 11 months. All freezer temp issues. We had noticed a number of ice sparkles forming on our unopened food. Frozen fruit was mushy. Temp usually read 0 degrees. One day I opened it and the temp was 40. Two hours later, it was close to 0. I started monitoring it closely. High temperatures occurred around noon. Zero degrees most of the time. After the third repair, service tech called Whirlpool and found part was redesigned. New part didn’t help. We understand the freezer has a heater in it, to defrost. The heater stays on too long. That explains why the freezer temp went as high as 50 degrees, while the fridge was perfect.I purchased this at Lowes. I always buy Lowes extended warranties. Thankfully, they bought back my 30 month old refrigerator. Kudos to Lowes warranty company. Never put on long holds. Fast response. I noticed the price for the warranty on refrigerators in this price range has increased by $100. Reflects a lot of repairs on refrigerator models. One thing though. I learned 3 repairs within a 30 day period is considered one repair, for purposes of their lemon policy. I will also add that the warranty company reimburses you 50% of the cost of filters. Simple process. I have read complaints that they make it too difficult to collect. That is just not true. Have been reimbursed $100 for filters to date. In 5 years, Even at the increased price, the savings will pay for the warranty. No brainer.

4 years ago, we purchased a Model UMV1160CW-3 over the range microwave. After 14 months the door cracked around the handle and eventually fell off. We made the HUGE mistake of buying the same model for ease of installation thinking that this would be a typical issue. We purchase another duplicate model in April of 2016 and less than 16 months later the same issue occurred. Spoke to customer service on 12/28/2018 and they told me that they would pick up the cost of the parts but I would be responsible for labor which actually exceeded the cost of the microwave. Exceedingly poor-quality product and support. Will not purchase another Whirlpool appliance.

Cleans average compared to previous dishwashers. Does not dry well even on high heat dry. Cycle takes about two hours and I have to run it during the day because it is too loud. The price was good, but I wish I would have bought a little higher grade.

Whirlpool wsv07 psl satina - I bought my whirlpool, two-door whirlpool ref last Jan 2013. Just few days before the warranty expires, I had prob with gasket on lower door. And now six months after the warranty expires, the freezer is not working and wont make ice anymore... and I will be charge 400php for check up. Reading on other reviews, I bet I am buying a disposable appliance from whirlpool. The national ref of my sis been a service to her for more than 10 years and its still going good. Our GE ref prior to whirlpool serve as for 19 years.... but this brand sucks.

The only thing cheaply made is the push latch on the dryer. Both are pricey for what you get, I thought, though they were the cheapest Lowes offered. We have had the pair for a little over a year. So far no real problems, though we really do not like the latch door. You have to slam the door to get it to close. To do it over we would probably have shopped a little longer and for the same money got a better deal.

Purchased 9/23/2013 on 5/20/2014 no hot water. Called Whirlpool, unit has a 6 yr warranty. Brian advised me no one close to our area to service. He told me to contact a local plumber, they would pay for parts and $75.00 in labor. I attempted a couple of calls and could not find a plumber that was willing to come out and let us pay just the difference, after parts and $75.00 in labor and them bill Whirlpool for the remainder. They wanted between $225.00 and $300.00 plus parts. Lowes where we purchased the water heater told me to call Whirlpool back and get an RA# and they would be happy to exchange the water heater. I called Whirlpool and they (Leigh) refused but did say they would pay 200.00 in labor plus the cost of parts. The unit was only $231.23, but they would rather pay upwards of $300.00 than just let us get a new one. I asked Leigh if this made sense to her, she said it did. I guess Im just ignorant because it doesnt make sense to me. Whirlpool COULD NOT even find a plumber that would come out to our small town to do repairs under their OUTSTANDING WARRANTY. I have laughed at these people and cried over this whole situation. I can honestly say I will NEVER buy another Whirlpool product and will let everyone I know and even some I dont know (lol) how horrible this experience has been.

The washing machine is so loud when it is on, drowning out conversations esp when cooking or eating (it’s located in the kitchen). The machine tumbler has to be constantly readjusted no matter the size of the wash or how many times my husband or myself adjust the tumbler; consequently the washing machine is always dancing, making a horrible banging noise. The washer is under 6 years old. With that said, when you open it, the lip is all rusted out.

I purchased a Whirlpool Gold refrigerator in May 2012 and about 8 months ago, ice started to form in the freezer. The ice melts and water drains out, so when you come in the kitchen all of the sudden you step in a puddle of water. I called CS and they told me the best they could do was authorize part(s) and the labor and service call would be my responsibility. Everyone knows service cost way more than parts.

Have an old Estate by Whirlpool, still going, no problems, washes well. I can control the wash by adding more water, stopping it and restarting it. There is nothing like the old washing machines. I have seen and used the latest and greatest, but they cannot compete.

Our gas stove (Whirlpool WFG714hLAS1) has been working fine and it looks great. However I just tried the self clean cycle to clean it up. I dont do a lot of cooking with only the two of us, but I like to keep things clean. I was very surprised after the first time - it didnt look much different than before I ran it! I was used to simply wiping down the oven following a cleaning, just removing the leftover ash. I havent had to scrub an oven for many years and it is very hard for me. I ran a second cleaning cycle and it didnt look any cleaner. We both had to kneel down and try a variety of non abrasive cleaners which finally got most of the grease spots, but not all. I guess we will just have to cover the roasts and try to keep aluminium foil on the bottom rack as much as possible. PLEASE re-consider buying any brand stove that has this awful feature, unless you like cleaning ovens by hand!

We have had this range in our new home and in use since May, 2019. The first range had to be returned after its first use due to flaking of the interior walls; a problem the company acknowledged. Since then we have been so unhappy with its ability to maintain the oven temperature. Contrary to the instructions, we calibrated the oven temp and found that it would vary up to 20 degrees lower than the set temp. When set to 350, it would come up to that temp and then cut off until it fell to 330 when it would come back up to 350. That is a great differential noticeable in the time it takes to heat an item and which greatly affects baked goods. A similar lack of consistency in control in the range elements is apparent as well. Now those are major defects. Minor defects are: it is NOT a rapid preheat at all, both lights are on when the switch is engaged even though only one oven is in use, there is no clock function when the timer is in use and the range surface is difficult to clean as it streaks which is visible with the black finish.

Just purchased a new Whirlpool Counter Depth, French Door, Freezer on bottom, Refrigerator from Lowes. Delivered Sept 1, missing the flap that makes the seal between the two doors. Shelves can be seen inside the fridge with doors closed. Exposed wires on the side of the door in a port with no cover. The fridge is unusable. Cold air flows out between the doors, temperature will not go lower than 45º. Moisture build up on the top and dripping down through the fridge. Frost build up on the back. Refrigerator runs continually. Had to shut it down. Called Whirlpool Sept 2. They will not replace the defective product. I must wait for a repair. The promise was within 24 hours for a technician to call. Called them Sept 2. Local family operated appliance repair company did not receive the request until Sept 4. They do not have the part nor does the parts supply company they deal with. Its on back order. Whirlpool has the part but long weekend and it will not be here until Sept 8 at the earliest. Whirlpool has advised Lowes that the issue is dealt with. I will see the technician on Sunday (Sept 6). Small family Business does not operate on Sunday or holiday, Monday, and have advised Whirlpool of this multiple times. Whirlpool doesnt care. I paid $2700 and do not have a working refrigerator. I will never purchase another Whirlpool Appliance.

I had a Whirlpool Natural Gas Water Heater professionally installed on 2-27-2107. This unit came with a Honeywell controller and thermopile assembly. Today is 05-18-2019 and the unit is not inoperative. The pilot is lit but the burner wont light. Here are the issues that I have come across so far: When I go to the Whirlpool site there is no direct link to Whirlpool water heaters, just kitchen appliances and washer/dryers. When I click on parts and accessories link it gives links to washers, dryers or pedestals. Again... No information about water heaters. I scroll down to the bottom of this page and I see a link to All Replacement Parts When I click that it takes me to another site managed by RepairClinic. When I enter the model number for the water heater it says Not Found. I entered the part number for the thermopile on the tag on the orange wire #321165-002 and 100078039 and again it returns as Part Not Found.Its obvious that Whirlpool is putting little effort into supporting their water heaters or their customers. I called their support line and they were able to order the thermopile assembly for $55 plus $27.95 in shipping to get it here by Tuesday. Today is Saturday. So that means almost 4 days without hot water. And since this water heater was a warranty replacement for a previous one that went bad they will not cover the cost of replacement parts for the thermopile. Lesson learned: No more Whirlpool purchases for any of their appliances.

We have been very satisfied with the way our dishwasher has performed over the years. It cleans the dishes well. It runs somewhat quietly. It doesnt seem to use too much detergent to get the dishes clean.

First F1 symbol on washer took 6 months to resolve. All we needed was new motherboard and couldnt mail it to us even though we could replace. It had to be an authorized person. Well we had one and they never put him in the system. Finally got that taken care of, 6 months of having to press pause and restart 5 times just to do one load. Arrrrrggggghhhh! Now water leaking out the bottom. Called again, on hold, then on hold again to be transferred to tech support. Yeah, right. No tech support. Talked to management, they could care less about us even though we have other products from them. Dont buy, they are lemons. We had ropes for 15 years and lasted through everything. Thanks Whirlpool, heres to losing a customer!!!!

Whirlpool slide in range, microwave, dishwasher, KitchenAid fridge: All appliances, stainless finish, were bought with my home in October 2006. Range - Within the first year, I had problems with the outer plastic pieces breaking, the motherboard and the oven and broiler not working. The screws holding the knobs on fell out several times. The oven door was fixed several times this past year until finally it fell off and broke for good and now the oven does not work at all. Microwave - The rotisserie motor stopped working this past year. Dishwasher - Just after the first year, the outer shell of the door came apart. KitchenAid fridge - Within the first year, the temperature adjuster broke. The second year, the ice maker stopped working. This year, the ice maker broke again and the motor quit working twice already and all has been repaired. The freezer handle has fallen off as well.

As part of a new home purchase from Pulte, the combo oven/microwave can with the house. After one year of usage, the oven liner started the pile and crack. We have a two year Whirlpool warranty through Pulte our builder. When we called the dedicated line for Whirlpool-Pulte to report the issue, we were told that Whirlpool must send a technician to take pictures and see what is going on. The technician shows up and declares that the oven is damaged and repairable. But Whirlpool reject to replace the unit claiming that this is a cosmetic issue and it must have been reported to them within 30 days from buying the home, as this is their policy for cosmetic issues.We did some research on our own and we found out that Blue color liner ovens have a well known issue, but Whirlpool keeps putting these into their products. Our builder is not able to get them to replace the unit as well. I will not ever buy any of Whirlpool products. Be aware if you want to purchase any Whirlpool appliances, warranty to them means nothing, even when they know that they are shipping products that have faulty into consumers.

This French Door refrigerator looked beautiful. There are only two of us in the home. We purchased it at the end of 2014 and it just keeps getting worse. The front of each shelving has cracked. They look like they are dried out plastic the way it cracks. The drawer tracks have seem to keep crumbling pieces off. This is not a cheap refrigerator by no means, this is the first time buying Whirlpool, and I believe the last time.

Remember the old movie classic Network, with the line, Im mad as hell and Im not going to take it anymore? Well, that is me and my new self-cleaning Whirlpool ranges that requires a manual cleaning kit (provided by Whirlpool after my purchase). I am angry enough that I have approached an attorney and I hope that if you have your own story about an AquaLift fail, you will include it on my website **. Thanks...

We have had this Whirlpool washer duet 5 years. It regularly rips shirts, underwear, socks, and sweatshirts. Jeans or heavy denim are safe but polos, hanes, or flannel are not. We have been putting our clothes into laundry bags and lingerie bags for a couple of years now to wash safely. Additionally it leaks out the front door. We clean it regularly and it still has mold growing on the rubber gasket - we do prop the door open also. All in all it is a terrible dryer. My previous Maytag was fabulous. I will never buy a Whirlpool again!

I really enjoy the self cleaning option on this unit. It really cleans everything without chemicals and then you just vacuum up the dust. My dislike is the ceramic top though. The top scratches really easily and hard to clean up spills during cooking. Overall I would give this stove a b rating.

We purchased this Whirlpool refrigerator at the end of July 2018. At the beginning of November 2019 all the interior lights went out at the same time. We called the store where it was purchased, and they instructed us to call Whirlpool. Because a year had passed, they were not willing to do anything other than put us in touch with someone who could service the refrigerator. We already know the repair will cost over $200. That does not include payment for the service call or the labor. At almost the same time we purchased a new Whirlpool microwave. We have also had problems with that. My advice is to stay away from Whirlpool products if you want something that will last longer than a year.

Bought these Whirlpool Cabrio Platinum combo about three years ago, nothing but junk from the get go! Washer never gets clothes clean, towels always come out smelling mildew and sour no matter what liquid soap you use Tide, Gain, whatever same results. Plus always mold coming from inside tub and yes we use refresh weekly and wash it out on refresh setting. I’m so tired of our towels smelling sour but can’t afford to buy new washer and dryer living on fixed income. If I could these would be in the recycling yard now. From everything I’m reading all new H e machines are crap and energy efficient my foot. I wish for my old style washer and dryer. WHIRLPOOL YOU HAVE LOST A LONG TIME CUSTOMER!

I am very disappointed with the purchase of a Whirlpool Cabrio Washer and Dryer I made about 3-4 years. The price was too high and the quality is extremely poor. It has a leak in the pump which will cost me $300.00 to fix. I probably would have been better off buying the cheapest washer and dryer set they had. At least, those actually wash the clothes and dont breakdown. Never again will I buy a Whirlpool and I will get every chance to share my opinion of them.

Cabrio top load HE washer - Ive only had the washer a couple of years. My husband bought it for me thinking it would make washing more time efficient and energy saving. Lesson learned! After struggling with this washer for the past year, I was told today that to repair it, it would cost around $800 or I would need to buy another washer. The washers bearings and tub need to be replaced and it will not spin properly or at all. Previously, I have owned washers for over 10 years each. This was definitely not a good purchase. After reading all of the other complaints on this site, I understand that I am not alone. It was also mentioned on one complaint of the possibility of a fire hazard with this washer. Whirlpool should be recalling.

I purchased Whirlpool Refrigerator model WRF989SDAM02 in June of 2014. I began having problems with the ice forming into a solid block shortly after having the refrigerator installed. I called for service several times over the next year trying to rectify the problem. Once the warranty had expired I continued upon the advice of Whirlpool Customer Service to schedule their certified Technicians to work on the problem. A year and a half and several hundred dollars later I am still unable to get ice cubes when desired.Ultimately I was advised that I would need to use the ice maker once a day to keep it from forming into a block. When this didnt solve the problem I again contacted Whirlpool, had another of their recommended service technician come and give his advice. I was told that the ice maker needs to be in constant use or it forms a block and this is a defect in the design of this unit. A Pro Tech Appliance Inc. Technician, an authorized Whirlpool technical representative, said the only way to have usage of ice would be if I made sure to dispense ice a minimum of 8-10 times a day.This is completely impractical and just plain ridiculous. I contacted Whirlpool again. They refuse to acknowledge this is a defect in the design of this model. I have replaced all parts that can be replaced, had the unit resealed and have paid for multiple service call. Whirlpool will provide no remedy for this problem. Now that the unit is out of warranty they have refused to provide a resolution even though its issue began while still covered under the year warranty. The ice in the ice maker is completely unusable and melts into a solid block within 24 hours if not in continual use.

I purchased a water heater in 2011 and have had the thermostat replaced at least 5 times! Now, not only does the heater not heat the water, but it has rusted through and ruined my floors! They say they will replace the thermostat (oh yeah, yet another one!) but what about the crappy thing in the closet. I will NEVER buy anything that says Whirlpool on it. They dont stand behind their product and have made no efforts to correct the issue. There has to be a lemon law clause that would be applicable in here somewhere.

The pilot light went out on our Whirlpool hot water heater. We followed instructions and were unable to relight. Our plumber was also unable to relight so we ordered new parts with associated overnight express costs. The plumber returned and worked for over an hour. When the pilot light came on the burner assembly burned out the new thermo coupling and that needed to be replaced again. This happened again. I would like to join the class action suit as Whirlpool has known about this problem and consumers are paying more than the original cost of the unit for repairs.

Had a part come off right after our purchase but was a easy fix to repair. The silverware basket also kept coming off until we looked at it and realized it was on wrong. This dishwasher is much quieter than our last one. It also shows fingerprints. We got this dishwasher in a group purchase during a sale at Lowe’s that included the refrigerator a stove, microwave and this dishwasher.

We have owned our side-by-side model # ED5HVEXVB02 for just over six years now. The first thing that went bad was the ice machine (just days out of warranty). Over the next 4 years weve had to replace 2 of the drawers; they break really easily. Here we are just 6 years out and we are on our 3rd icemaker. This refrigerator is a lemon. I sincerely believe they designed an inferior product so that they could get you hooked. We probably would have been better off after the first issue if we had sold this lemon instead of spending all of this money and future money that it will take to keep this product going.

Purchased our hot water heater in August of 2011. About 3 days ago, it just stopped working. Surely it should last longer than this, right? Nope apparently I was taken! We called the manufacturer and described the issue. They said it was the thermopile. They could send us another out in a few days but we didnt want to wait so we paid $50 for a new one we were able to locate at a hardware store. Nobody sells these! We replaced the thermopile but no results... Pilot will not stay lit. Called Whirlpool back and they said to hit the reset button which we did. Called a technician (several) which wouldnt touch the heater. Said nobody works on these because they are riddled with issues. I pleaded with him to test it which he did. He said the control box is out! He said to cut our losses and buy a new one! I am so very upset! I cant afford another one! We called Whirlpool back again to see what they would say this time - they are sending us another control box! After reading all of the complaints and being without hot water, I am not hopeful of a good result! I plan on replacing the control box that they send and then saving for a new heater! I want my money back which Ive heard just wont happen! I have also had nothing but issues with my gas stove made by Whirlpool ever since it was only 6 months old. STAY AWAY FROM WHIRLPOOL PRODUCTS!! Run!!!

Whirlpool Auto Load Sensing - I bought the washer in Aug 2010 and it worked well until the timer went out this year. Its only 4 years old! The repairman said it would cost $350 to fix - the machine cost me $469 to begin with! Whirlpool builds a poor quality product and Id advise people not to buy their brand of anything.

Had this model (WMH73521CS-6) installed as part of kitchen remodel. After 8 months, microwave is failing, indicating door needs to be opened, then closed to operate. This does not fix the issue or reset the condition. AND, there is no way to reset the microwave electronics, not even power cycling (unplugging and replugging from/to electrical outlet).

We bought a Whirlpool Cabrio 2 years ago and they are an absolute piece of junk!!! There is only 2 people in our family so its not like we are washing big loads. It doesnt get my clothes clean and the clothes stink. I have followed the directions on cleaning the washer and it does not good. Now my clothes are soaking wet at the end of the cycle so I have to put it on drain and spin just to get most (not all) the water out of them. And when I take my clothes out, they are just as dirty as when I put them in. Called a technician and its going to cost over $400.00 to fix. This is nothing short of robbery!!!! This machine is a piece of junk. I read over 500 reviews on this washer and they all had problems that cost as almost as much as the washer cost to repair. There really needs to be a recall or a class action lawsuit against Whirlpool.

Called Whirlpool customer care for help with identifying make and model number of a slide-in, ceramic cook-top range (one of their popular brands). The representative was cordial, patient and very helpful when it came to giving me directions on how to locate make/model information on the unit. That was until I let her know about a recent problem with the stove. The edge of the cooktop is much too sharp! My hand got cut while wiping down the stove top/adjacent counter. Although Ive had the stove for a while, Id never had that happen before; thats probably because I used a thin rag this time around to do the cleaning. I asked the rep if anyone else had reported getting cut by the stove top. She said, No. I let her know that my goal was to just them know about the situation, because such a sharp edge on a cooktop is a safety issue. She disagreed. But what could or should she have said? In all fairness, it came down to balancing loyalty to the company with genuine care for the customer.I do appreciate how kind she was in communicating with me, but am very displeased that once Id shared about the problem she seemed rather dismissive of the situation. How could the risk of being cut NOT be a product safety issue??? If you visit the Consumer Products Safety Commission website, you can see where risk of laceration is a reason some products are recalled. Based on that understanding, I would say that sharp edges on a ceramic cooktop IS a safety issue!

Im a renter, and I know the landlord purchased the least expensive stove for this apartment, but that shouldnt mean one has to absorb ongoing off-gassing fumes for well over a month now. The stove was installed 2-18-17, and its now 4-6-17, still havent been able to use it. Is this really off-gassing or is this what Americans have to contend with now! Oh and theres the little sticker that says Made in America and in small print it says designed and assembled in America, but no mention as to where the parts came from!!! The only reason Im giving even a One Star rating is because I cant continue through this review without at least marking one star.

I moved down to Florida in March of this year. I have always owned Whirlpool appliances and wouldnt think of buying another brand...... till now. I purchased in March a new washer and dryer set washer model #WTW4800XQ4. The washer is so noisy that I cant watch TV while its running (what a piece of junk). I asked when they installed it if there was something wrong with it and the gentleman from H&H Gregg said no, they all sound like that. I guess if you want quality you have to buy Japanese.... HOW SAD.

The Whirlpool repairman left today after replacing the burned out motor on my 5 yr old dishwasher bought in Feb 2012 and installed July 2012 as did not arrive from Quebec to Surrey BC until the end of June 2012. So the Finish dishwasher detergent was in the dishwasher as samples and coupons and recommended this Finish for use in the new dishwasher so I stupidly believed them and used it. Well last week my dishwasher stopped working after it started and turns out today the cause was from the Finish dishwasher detergent. I was told today after paying 393 dollars for the repairs. Not to use Finish anymore or I will have the same problem. To only use Cascade. So what is a person suppose to believe.

I purchased a Model WRF989SDAB01 Whirlpool refrigerator with the French doors and had it delivered in March 2014. The evaporator developed a refrigerant leak in May 2015. Whirlpool said it was not their problem since it was over a year since I bought it. The technician said this is a problem with this model. I am having it repaired under the extended warranty that I bought. One of my concerns is that the unit has two evaporators so the other one will probably start leaking any time. What a piece of junk. Dont buy Whirlpool. Their quality and service stinks!

I purchased a compact frontload washer. At first, I was getting a code f30, which took the technician weeks of coming to my home and changing different parts to finally accomplish that problem. After that, the machine would not go into high spin to wring the clothes out. So everything comes out soaking wet. After two different companies (Herbs Appliance and DanMarc Appliance which I got from my service contract) changed speed control, board, latch control, main computer, and top control board, the machine finally worked for a little while. Not long after, the machine is no longer wringing out once again. I am no longer under contract but had a repairman out three times to inform me this machine is a lemon. Whirlpool tells me I am no longer under contract, but my argument is this is not a new problem but a preexisting one.

We got the convection oven. It has no element like the one we had before with the fan. It is useless. We have to upgrade the temperature to get what we want. Difficult to clean. It does not cook like it should. We do not like it, period. Those electronic controls are not doing their work. No more Whirlpool appliances. Problems with the noise of our dishwasher also.

The microwave keypad is worn down after 10 uses making it difficult to read the pad. I just discovered the microwave was missing the front leg and they do not have a replacement part so I am stuck with a virtually new microwave that will not balance. It took 4 phone calls to their customer service department to try and sort out the problem. Poor product and extremely weak customer service department.

Despite my claim being submitted within the first 4 months of purchase, Whirlpool would not assist in solving our issue. We purchased all major appliances from Whirlpool, to furnish our new home in August 2021. All appliances were white. The top of our gas range began discolouring immediately following the first use. The inside of the four corners immediately began to ware due to heat. I figured Id have time to put my claim in, and thought to see if it got worse. Once I finally had time to deal with the issue, I contacted them only to find out that we only had 30 days from the date of purchase (of which included 3 months of waiting for the products to arrive) to claim the issue, given that it was considered Cosmetic. Easy fix, since theyd simply have to change the top of the stove, but Whirlpool denied our claim. Do not purchase this product, unless youre looking for a sub-standard product and customer service.

Self-cleaning oven system DOESNT WORK AT ALL! The company rep I talked with said the system only works on lightly soiled oven and doesnt clean at all on the oven top or sides. When I explained that my oven was less than lightly soiled (I rarely use it) and that I had run the cleaning cycle twice and none of the soil was affected. Apparently the company is aware of this problem and I believe customers should be made aware of it BEFORE purchasing. I was told there was nothing they could do because my appliance is out of warranty. I asked if they had received other complaints and was told they had. I am not surprised.

I paid ~$1200 for a new Whirlpool (French door top fridge and pull out freezer bottom) 7 years ago when I bought my house. I was so excited - and the appliance has been a problem from the beginning. It has always made a very loud knocking noise - even when it was new. I was told by the technician there was nothing he could do and Home Depot wouldnt help me with it either. My freezer has gone out three times - the last time was the day before Christmas Eve 2016 (a few days ago). I lost everything for my Christmas dinner that was in my fridge because that went first.Then when the service man came today, I was told it was the freezer that is causing the problem and everything had to be defrosted - plus they had to order a part that would take 3 to 5 days - so Im now going to lose everything in my freezer as well. All in all with the three service calls and the food I have lost probably amounts to around $800 - $900. I am so upset and cannot get any help from anyone. So, Im just warning you - NEVER buy a Whirlpool!

The Worst experience with Gold Series Mod WRF 757SDEM01. Purchased from Best Buy June 2016. $2215.00. Within 6 months The interior light began going dark within 6 months. Our very reputable warranty repair service ordered a part that did not repair it. Was only temporary. They did figure out that the circuit board was bad and promptly took care of our problem. Next I kept noticing water appearing on our wood flooring. Let it go because it only appeared sporadically. Called Whirlpool only to find out they switched to a warranty repair service that was inept and inexperienced. Said he could fix it. Blamed it on a freeze-over so I let floor dry up then re-started and refilled. Thought he did fix it cause it made sense. When reassembling he broke to upper freezer try glide. Then 3-4 weeks later I notice one morning water again on my wood floor. The dripping had been running beneath the wood slats and had seeped up through the joints. Now the flooring wood has swollen and will need to be replaced because of this. This is the second time I had to unload all food and store at neighbors and give away. Extremely poor engineering designs as each time the ice dispenser is used, nothing prevents ice from flying out onto the floor ever since day one. Same with water. The release does not shut down to prevent water or ice from pouring out onto the floor when removing any size cup. The refridge doors must both be opened to use the lower level drawer. Loses much cooling with having to always open both. Next, weve come home MANY times with the left refridge door partially open because of the difficulty of the mechanism to secure at closing. This happens to us 5 times a week for three years-honestly!. This was the only refridge we could find that would fit our opening in a 20-yr-old home. The fridge is so heavy one man cant pull it out of its opening. Only 2 very small wheels in front and skids in rear stick due to weight. Weve confirmed this is not a spigot leak from the ice maker. Finally (but probably not) the ice container allow much air in because of having to open the left door that your ice is always melted together plus it too small for a family of two and ice must be purchased when entertaining. And to top it off, the human that took the warranty call this time is foreign and my wife could not get them to get our last name spelled correctly nor the phone number correct after constantly repeating it. This unit and model is an absolute lemon. Im going out today to find another unnecessary $2500.00 to buy another.

It was about 6 years after purchase that the ice maker completely quit making ice. To change the filter you have to get down on your hands and knees to do so. If youre elderly, this can cause a problem. Overall, it was a good refrigerator.

Ive read the reviews on this appliance. First of all the all of the washing machine being manufactured are designed to save energy and water. The water is loaded in the machine based on the WEIGHT of the clothes. the washing machines no longer have the features to (small, medium, large load) so the consumer can fill the machine. Having said that, most sales representatives will tell you appliances manufactured today are no longer designed to last 15-20 years, although they are way more expensive than the workhorses made in the past.I got rid of my fancy Samsung washing machine because it broke down at least 4 times within the first year of purchase and decided to go with the whirlpool because Ive had a workhorse in the past that was worked excellent. I love the fact the washers no longer have the agitator in the middle which allow me to wash my king sized bedding without the machine becoming unbalanced or making a lot of noise. So far the Whirlpool Cabrio washer and dryer is working very well. Id rather give the Whirlpool a chance any day over the new johnny come latelys, which are more aesthetically pleasing to the eyes but are failing miserably in performance. I also love my Cabrio 8.8 dryer. They both work better than the Samsung models I got rid of.

FRUSTRATION!!! It is unbelievable that even appliances have become DISPOSABLE! Where are the days of when our parents bought well made appliances that LASTED 20 years with NO problems??? There was satisfaction knowing that a purchase of an appliance was $$ well spent! These days it costs MORE to replace parts than IF you purchased a brand new machine! We purchased BRAND NEW Whirlpool Duet Sport Washer AND dryer in 2007. The washer has been repaired a total of 5 times and the dryer 3 times!!! IN A SPAN OF 10 YEARS! Are you serious?! With the $$ spent on warranties/ labor/ parts: WE could have purchased new appliances. What is WRONG with this picture? IT IS ALL about making money on REPLACING PARTS/WARRANTIES/LABOR!!! Forget the consumer that is spending THEIR hard earned money to buy the appliances initially. Short of going to a laundromat, the consumer needs to purchase a washer & dryer. So I guess it is a vicious cycle of REPAIRS/REPAIRS AND MORE REPAIRS!!!

We purchased a Whirlpool Gold Series dishwasher from Lowes approximately 2 years ago. Serial P32105232. We noticed a dark stain coming up in the hardwood floor. It was a water leak from the dishwasher appears to be from seal when water cycle leaves unit. This has caused over 70k damage to our home. Ruined entire hardwood floor kitchen cabinets warped so all need replaced. Our insurance company has made a disaster after owning home 10 years. Custom cabinets that match the laundry room as well. No to mention. The jackhammer used to bust up 800 sq foot of flooring and the concrete dust in our entire home. Please advise recourse.

I was excited to have an energy efficient washing machine and chose the Whirlpool Cabrio top loader. I truly wish I had read reviews rather than trust the salespersons advice. It does not clean clothes properly at all. They come out smelling dirty and are covered in white goo, even when the machine has just been cleaned. Stains never come out despite all of my efforts. Now I have water leaking out of the bottom as it fills. Not impressed at all. What a giant waste of money.

We have had this water heater for less than 5 years. It was purchased new from Lowe’s. This is the second time we have had to replace the thermocouple and are told that we have to order the part from Whirlpool. Really? What do we do for hot water in the meantime? This is a very disappointing response from Whirlpool and Lowe’s. I will never again purchase anything from either company. We had to buy a new heater today, pay for installation and permits. This is a rip-off by Whirlpool and Lowe’s.

We have these appliances in our apartment. Its a gas range with a microwave over the hood. We did have the microwave replace a year ago, we have been here for 5.5 years. Its a good stove, we would consider buying one for ourselves.

I purchased a new Whirlpool range and had it fitted for propane. I used the stove daily and within two weeks, the temperature started fluctuated constantly. Several things I tried to cook ended up burned. I called Whirlpool to ask them for a possible solution. They wanted to send a repair person. I live on an island and knew it would take forever to get someone here. My appliance person said it could be only two things - the temperature probe or the computer board. I purchased both things and had them shipped to my address at my expense. It cost $257.00 to get the items. My appliance man on the island installed the two new items. I was hoping that would fix the problem. I am sad to say it did not! The oven still fluctuates wildly. I set the temp for 350 degrees and it shoots up to 450 degrees. I turn the temp down to 325 and it settles in at 350 for a period of time. Then, without any warning, it will shoot back up to 500 degrees. I have to open the door and let the temp back down to 350. This is how I have to bake and cook with this disaster. Wish I never purchased a Whirlpool appliance!

This refrigerator was already part of the appliance package that came with the property. I dont think if I had a choice, I would choose this brand. The stainless steel finish has rust spots, the top shelf has cracked and it is less that 5 years old.

I have had two Gold Series dishwashers before but the model number I used had been discontinued so I purchased the W10491035A about a year ago in 2013. It has to be the worst dishwashers I have ever had and we have used them for forty years. Its loud. It won’t dry the dishes, and unless you wash I dont mean rinse, most of dishes are not clean, and that is with the recommended detergent. Whatever you do I would suggest not buying this dishwasher. I dont even know why they would offer a machine such as this.

I am very upset about this Washing Machine and Dryer. I did my research in 2012 and found good reviews on drum size, water usage, bells and whistles. I purchased the set in Feb of 2013 (its on Jan of 2017). NOT EVEN 3 years later, I write to say that my washing Machine is ready for replacement! I paid 989.00 for each and last year the Spring on the Glass Top was worn away, I am told because bleach was splashing up in the spring area. Cost to fix with a local repairman... $235.00. Now I noticed a small amount of water on the floor, move the washer and there is a LARGE amount of water Stain and my cycles keep popping up UL. Two separate repairmen (because I didnt believe my trusted first one) tell me the cost for the shot bearings and seals will cost almost as much as a new washer! I am a family of 3. I have a daycare so do a few extra loads, but am not using this any more than average to low use. Not to mention that on top of all of this the computer appears to be shorting out and to order a new panel the repairman places that at an EXTRA 300.00. SO UPSET! The dryer dries very nicely and is quiet however, the motor went out 6 months ago and we replaced that, not wanting to but better fix than scrapping it only 3 years into a product expected to last well over 10! The little clip on the door to lock it is also loose and hardly locks now. The repairman is having trouble even finding the small part. Young Couple Expecting to have a brand new 1900.00 washer dryer set last a long time only to be out of warranty and already needing to buy a new set! DONT EVER BUY A CABRIO WHIRLPOOL.

I have had my Maytag (Whirlpool) Centennial Commercial machine for 10 years and it has not required any repairs or have given me any issues. I love the water level sensor that doesnt require me to select a load size. I would highly recommend the Whirlpool brand to consumers.

I paid about $400 for this dishwasher and the regular price was over $600. Got a good deal. It washed dishes wonderfully. All I had to do was scrape the chunks off. It cleaned the rest. BUT... at a certain point, it started NOT cleaning. It was only about 6-7 months old. It was to the point where everything just came out kind of slimy and food grit was re-deposited on the dishes. I cleaned both filters. I made sure there was enough Rinse-Aid all the time. I ran hot water in the sink before starting to make sure the temp was hot enough. My husband went online and someone had instructions about cleaning the water intake because it could sometimes have sediment buildup. Not a difficult process, but there was no gunk in the intake filter. When I listened to a load it seemed like it drained, (most start with that), paused, rinsed for a couple minutes, paused, drained, paused and refilled for the wash cycle. So the pump worked, the arms went round and sprayed. Nothing was in the way of the arms. After it started the wash cycle, it seemed to just stall. It would spray for about a minute and then stop. Im not sure it sprayed after that. The timer kept counting down. It said dishes were clean, but it was an absolute waste of time. I was ready to go buy a cheap dishwasher and throw this one in the dumpster. I think it is a 720 padm??Just after my husband checked the water intake filter, we started another cycle. When it was rinsing, he opened it up and everything seemed to be working ok. It drained, then filled and started the washing cycle and then stopped. He opened it back up and surprise, the water was full on the front level by the float (that turns the water filling off). But in the back of the dishwasher, there was only about an 8th of an inch of water. Online it said the water should fill to just about the top of the heating element. It WASNT. Problem? It wasnt LEVEL. The instructions when installing said it should be leveled. We did when installing it (when it worked great). But looking back, we put in a new hardwood floor about the time it stopped working ok and we didnt put 2 and 2 together. We did not re-level. When we pushed the dishwasher back into its built in cabinet, it must have gotten OUT of level.The rinse part worked I guess. Then it drained and re-filled. After re-leveling the dishwasher, we opened the door at that point. The water was a level depth front to back and side to side. My husband explained what he thought had been the problem to me. When the wash cycle starts it fills, the float shuts off the water at the appropriate level. THEN... the dishwasher starts to pump and fill the arms and the tube up the back that feeds the upper washing arm. So much water goes into the arms and up that tube, the dishwasher looked almost empty of water again. As the dishwasher was now level, it began adding water to compensate for the arm/tube filling. Before the float would shut off too soon because the front part of the tub was full but the back wasnt. Without enough water, the dishes were NEVER going to/COULDNT get clean.The re-leveling made sure that the float didnt turn off the water filling until there was much more water, the CORRECT amount. The next load cycled all the way through, spraying much more than Id heard before and the dishes were clean. P.S. I also got some dishwasher cleaner and used that on a couple empty cycles. I NOW LOVE this dishwasher again. FYI If my husband wasnt handy Id have junked this thing. We HAD leveled the dishwasher when we installed it. Just didnt realize it COULD get un-level just pulling it in and out of the cabinet to install new floors. Check out all the troubleshooting stuff in the manual. But if it doesnt help, put a level inside across the bottom rack, front to back and side to side and make sure the bubble is in the middle of the two lines.The previous dishwasher I had, just made like a fountain of water that went up the middle of the dishwasher into a sort of funnel filling the upper arm. THIS one has that tube up the back and it curls down under the filter and Im guessing it is more sensitive to being OFF LEVEL, because the tube doesnt go straight down, it curls and lays across the bottom of the tub. Without being level, there was never enough water to suck up that tube to start the the actual wash cycle and it just stalled there till the timer said clean at the end. IE: dishes never did wash. BUT IT DOES NOW! Woohooooo!

The 12 year warranty, means nothing. The heater only worked for 30 months, and then its upper sensor fault code flashes, and the heater shut down. I called Whirlpool, and they have me use an ohm meter to help troubleshoot the problem. So if you are not handy, you are out of luck. They decided it was my control unit that is defective. They will send me the part free, but I have to pay shipping and installation. What a deal, and what kind of management would dream up of this. The heater is marketed as a 12 year warranty model (only on the tank). Would anyone, having been through this, buy another Whirlpool product?

WARNING: Do not get the warranty plan through Whirlpool if you have stackable washer and dryer, you will have to remove the dryer yourself before they come out to service your appliances. I was willing to pay extra to have them take it down, the contractor said I had to call the extended plan service, yet 6 telephone numbers later to include the complaints department to no avail... Whirlpool contracts out so get your own and you may save a few dollars!

I have a smaller/apartment size fridge. As a 1 person household it is a perfect fit. Works well & wasnt expensive. I am a Foodie, having it so nothing is too warm/cold, all the temps are equal, is a big deal. And in 10 years no breakdowns.

Whirpool WFW9550WW-00 Front Load Washer - Washer was purchased 08/09/12. No problems until 07/12/15 when washer stopped working mid-cycle. Motor control board needs to be replaced, actuator needs to be replaced. $500+ Our local appliance store suggested we call the Whirlpool customer relations number and ask for the parts to be sent free of charge. We would pay labor. They gave us the model number, serial number, the diagnostic info. Long story short, customer service told me she didnt know why I was told to contact them. They can not predict the life of a machine. Less than 3 years for this machine. 22 years for my old Kenmore. Our old Kenmore never had a problem, but we thought that we should replace it in 2012 in case something happened with old machine. WISH WE KEPT THE 22 YEAR OLD KENMORE.

My house was built 20 years ago, with all Whirlpool appliances; built-in microwave over the electric oven, gas cooktop, and under counter dishwasher. The oven just gave out. Everything else works fine! Let me repeat that. I have a 20 yr old Whirlpool microwave that works just fine! Well, since the oven broke, we thought, maybe its time to update all the appliances. We went to the large appliance store from which our original ones came, and were told that all microwaves are now made in China by Sharp, and are crap!! Wed be lucky to get 3 years out of one. My jaw hit the ground. I couldnt believe the appliance salesman was telling us this! In fact, the appliance repairman that diagnosed my oven to be unrepairable ($100 trip charge, thank you very much) didnt have much good to say about the newer refrigerators... They contain much less Freon and dont seem to hold up as well... So, I guess Ill just keep my old appliances going as long as possible! How can appliance manufacturers stay in business!

The oven has not worked correctly from day one. I have to use a thermometer plus after the correct temp is indicated I still have to wait another 15 minutes for the oven to reach the desired temp. Also have to set the temp for 25 degrees higher than the one I want. The burner that supposedly has two sizes in one is basically useless. Temps are not correct and sizes are misleading. There is a tiny groove around the outside edge of the stove top that gathers crumbs which are hard to clean out.

I purchased this washer (Whirlpool Cabrio HE) 2 years ago against the advise of many people including my husband due to the cost, $850 for what is now no more than a large paper weight! It had never really done a good job at cleaning our clothes. About 6 months ago, it started not spinning enough to remove all the water from the load. I thought, no big deal, I will just use the extra spin cycle. It became the normal thing - wash, spin, extra spin. Well, then it became wash, spin, extra spin, extra spin. I noticed 3 months ago that it was not even agitating. It fills up, sounds like it is agitating and then drains. There was no movement from inside at all. All along I am getting from my husband. told you not to buy it! I gave in and called the repairman - $185 for a console, $26 for a sensor and $55 for a couple of drum clips and then the $35/hour for the repairs. I would rather spend a couple hundred dollars and buy a washer with an agitator that really works. I would never recommend this washer to anyone!

I have purchased two Whirlpool microwaves since 2007. The first unit lasted 5-1/2 years, the second one lasted only 2-1/2 years. I used it at dinner but several hours later it was dead. After reading other reviews I have decided it would be cheaper and less stressful to get a new one. So Tomorrow I will be purchasing a new microwave which WILL NOT be Whirlpool. I no longer have confidence in any of their products.

I had a Whirlpool dishwasher for year and it worked great, but the baskets were rusting. I decided Feb 2014 to purchase another Whirlpool dishwasher. It did not clear as well as my old dishwasher. The seller of the dishwasher stated it was our water or detergent. The water and detergent were the same. The only difference was the dishwasher. Day prior to changing the dishwasher, the dishes were clear and the day I changed the dishwasher, the dishes were not clean. November 2016, the main board has gone out. The part costs $148, plus the service call. I called Whirlpool. They stated they would sell me the part or would discount a new dishwasher. I think they should discount the part!!! Whirlpool makes most brands of dishwashers, so you cant change companies. Their quality is all you can get.

Whirlpool Gold French Door refrigerator freezer on bottom - I purchased my refrigerator at Lowe’s on 9/26/12 and it cooled OK for the first 3-4 months but it was very noisy along with water dripping from the ice maker door. Then sometime in Feb. my freezer started to warm so I contacted Lowe’s service and they scheduled Tech. to come the following week. He found that freezer evaporator was freezing - suspected a leak and ordered one. Replaced that, and a short time later it was warm again. To make a long story short they have been to my house approx a dozen times replacing the freezer evaporator, control boards, adding refrigerate, and replace the reversing valve, and no time at all it was warm in the freezer again. Tech could not find anything wrong with it and added a little refrigerate and the problem was solved... I thought! Two months later the freezer was warming again. Now they say it’s the evaporator on the cold food side has a leak and needs replacing. Been waiting two weeks now on parts. Talked with Whirlpool and Lowe’s about replacement with a new unit but they tell me they only cover parts and labor. Needless to say this is my last Whirlpool appliance!!

My experiences using Whirpool ranges and ovens have been very positive. As a matter of fact, that is the brand preferred by my family through several generations. Durability, reliability and warranties have been the main features we have found useful. Most of the ranges and ovens have been replaced at home, always with Whirlpool brand, but with added improvements that manufacturer come up with, in order to integrate our devices to the latest technologies. I would recommend this brand to the readers, friends and neighbors.

Same old story! Whirlpool Cabrio is a lemon! I did pay a service guy to find out what the problem was - $70. I ordered a control board for $210, I still had the problems. I ordered bearings for $80. Yay, my Cabrio works! Well, this was all 4 months ago and here we go again. My washing machine is doing everything it was before I replaced the brand new parts. Im so mad! I spent $360. I couldve had a new washer, not a $1000 Cabrio, but who cares at this point! Anything seems better than this pile!

Our microwave is less than 8 months old, hardly used and only for heating items. Besides the point, being under a year old. It began to make noise and pop, spark sounds with the smell of burning wires and promptly stopped working. We called the customer service line and began the long frustrating circle of completely bizarre conversation. Maintaining our belief this is a fire hazard and not wanting it in our home they insist on a repair person coming after trying to sell us Extended warranty, Why would we want Extended warranty when the warranty is NO warranty, it seems, whatsoever. After requesting to speak to a supervisor 3 times. A overly bubbly person comes on the repeat same spiel and to make an appointment for 1 week away from 8am to 4pm to be available for a phone call to make an appointment to see about repair on said fire hazard microwave that is less than a year old. This appointment is made with repair place and they too are confused and noted Whirlpool said this is not covered under warranty, and they too would contact them.Today Whirlpool Canada calls and gives number to repair place to book appointment, Hello we already have one and the frustrating verbal dance continues. 5 minutes after this call the repair place calls, as whirlpool contacted them as well to book appointment, which we both could agree this is the bizarrest situation since we already have an appointment, from their appointment. We keep saying we feel unsafe, this is a fire hazard. Which they completely ignore. This is unacceptable and extremely poor service.

Hi team, I have to lodge this complaint after because of getting continuous problems I have suffered with my Whirlpool fully automatic washing machine top load 11 kg bloom wash 360 degree. I purchased the abovesaid brand new washing machine on 1st Jan 2017. Since the purchase I am struggling with this machine. I raised the fault in the beginning itself and the service was done on 5th of Feb. Jobs sheets enclosed here with.Similar issues kept on arising and whenever I raised those issues with the whirlpool team, they mentioned that company policy is to repair the faulty part if it’s in warranty and they will not replace. They suggested me to go for the AMC and to be on the safer side, I also took AMC under warranty period only. (AMC card - My cheque dates and service details all are mentioned onto it.) Recently I faced another issue on 26th Feb for which ticket was raised. Engineer visited on 27th Feb and advised us to replace the motor part. On 3rd March they replaced motor mechanism and ball-bearings. Then engineer advised us to check the working by giving a trial wash.I started the machine to wash clothes and after 20 mins machine started making abnormal noise. (I have made video of it, audio of the video captured the noise). I again called up the service engineer immediately and informed him about the voice coming out of machine and he gave a lame answer by saying “It is normal sound”. Then I again called Whirlpool and requested senior engineer visit to resolve the issue. Senior engineer visited and told us that one of motor screw wasn’t tighten properly. It opened while running the machine which completely damaged the motor.After that I am continuously calling to service centre to get the updates on my machine motor replacement. Finally they mentioned that they dont have motor part available with them due to company ceased this model productivity. When I raised this issue with the Whirlpool team they mentioned that they can only pay 40% of the machine value, because I had AMC. However, I did mention that this damage is caused by the negligence of their service engineer, but they didn’t discuss anything about it.When I continuously chased them they dropped me an email to refund only the 40% of the machine value. I feel cheated and harassed!! When I bought the machine they gave us 10 years warranty now they mention that motor is not available as it’s a 5 years old model. My grievance is that since I had already taken the AMC and the damage was also caused by their engineer, why I have to bear the loss. I have already struggled a lot with this machine since last 5 years from the day I bought this machine and now I am losing my hard earned money. Kindly do the needful. Documents attached as follows: 1. Serial number of this machine 2. Bill/ Invoice copy from dealer 3. Job sheets4. AMC card (with 3 years extended warranty) Thanks,Pratibha

We had purchased a Whirlpool Duet Sport Washer and Dryer in 2007. Since that time we have had several repairs on the dryer, resulting in us having to purchase an entire new unit in 2011 (4 years old), along with mold that has accumulated in the washing machine on the tub and rubber seal that cannot be removed after several attempts utilizing several products that were recommended. The end result is our laundry that has been washed - comes out with a musty odor. Not happy at all with the top of the line, best possible machine to produce clean laundry as was sold to us! This has been a nightmare, and a totally dysfunctional appliance that should have lasted longer than 5 years!

Whirlpool Cabrio HE washer - Purchased my set in 2007. Has not worked properly most of the time we have owned. Lid locks our clothes in when the machine malfunctions and we have to barter with the machine for hours of Google suggestions to get the clothes back out. Still dirty. Or still soaking wet, not spun. Ive never seen so many error codes from one machine. I would never purchase this brand again. The only pro is the load size, which trust me - we have spent more time, water, energy & $$$ with the washer not properly working than the large capacity has saved us.

Replaced the “brain” twice. No hot water for 2-4 days each time, waiting for part to arrive. Now I have to replace the nylon drain valve because it won’t shut off. Gonna use brass replacement. Fortunately I have it drain to a sump pump so house isn’t flooding. Don’t buy Whirlpool water heater from Lowe’s unless you enjoy this kind of thing. Consolation: the folks at the help line always answer the phone and are knowledgeable. And they’ve heard these same complaints over and over. One guy even said to buy AO Smith as they are made in Tennessee instead of China.

After almost 5 years of satisfactory performance, our $1200 Whirlpool Duet washing machine WFW9400SU1 requires repairs costing over $1100. Similar to another complaint listed, some parts rusted out, leading to extensive damage during use, which we realized only after the spin cycle became incredibly loud. Now the entire gut of the machine (bearing, drum, arm, casing, etc.) needs to be replaced - $900 parts and $200 labor. I trust my repairman (who said theyd seen this type of problem before with Whirlpool) especially because he recommended buying a new machine instead. I called Whirlpool, and they said they could do nothing for me which made me very angry. This is a mechanical problem that could have been avoided by using proper materials. Whatever happened to the washing machines that would last 15-20 years?

I purchased my Whirlpool refrigerator from Best Buy 11/20/19. It has been nothing but a nightmare. It freezes up and defrosts into the refrigerator.! I called Whirlpool about the situation. The company they use to fix my fridge S&S Appliance has not been keeping accurate records. I have all the calls from Best Buy and S&S Appliance. I was told today-all my records didn’t count. Best Buy Geek Squad couldn’t repair so they turned everything over to Whirlpool. So about every week someone comes out and fiddles with it and tell me it is fine. 2 days later the same. I have owned many Whirlpool products and never have I been so disappointed. Their service has been neglecting and I don’t know how anyone would want to buy Whirlpool. They have set me up another service appointment with S&S Appliance. Obviously I have bought a lemon and no one takes any responsibility. Good luck with Whirlpool!!

Our Whirlpool Cabrio Washer did a decent job for the 3.5 years that weve had it. Last week, it stopped spinning properly after rinsing, leaving the clothes quite wet. The repair person said it needs a new control panel and is not worth repairing. So, we have to buy a new one after such a short time. Very disappointing. Next time, well try another brand and buy an extended warranty this time. Buyer beware!

Absolutely love the oven/range electric smooth top! Cleans up well. Works well. We bought new along with refrigerator and microwave as a set. We had problem with icemaker, told us we needed new door (well within warranty coverage) then wrong door was sent and company told us that they could only send one door and that was it. Incorrect door sent back. Repairman attempted to fix several more times. We finally quit trying. Husband says we can never buy Whirlpool again.

I purchased a total of four Whirlpool appliances in June of 2008. Almost thirteen months after the installation of all four appliances, I experienced a problem with the control panel on the Gas Range GW397LXUB, and a sensor control problem with the Microwave GH5184XPB5. Fortunately, Whirlpool agreed to repair the appliances at no charge because it was so close to the end of the warranty. The microwave was an easy fix and simply had to be unplugged, reset and plugged back in. However, the entire electronic control panel had to be replaced on the gas range. Several of the buttons simply stopped working and I was only able to bake at 350 degrees. Again, almost thirteen months after the installation of the new control panel, it happened again. Same buttons stopped working. When I contacted Whirlpool, they refused to replace the part because I was no longer under warranty. Whirlpool refused to admit that there was a problem with the control panel, so I guess it was a crazy coincidence that I experienced the exact same problem on both. I filed an official complaint with Whirlpool in hopes that if enough people do so, they will issue a recall. I am now experiencing a problem with my refrigerator ED5FHAXSB03. The fan vibrates so loudly that you can hear it throughout the entire house.

I purchased a Duet Dryer less than a year ago and it stopped working. Got the warranty people to send someone to diagnose it. The repair person ordered two parts to fix it (they took the control panel off the order for some reason). They sent a second inept person to try and install the part they did send and it did not work (He was the most condescending person I have ever met but that is another story.). Of course it did not work and they actually have to replace the control panel AND the electrical panel (which as you know was ordered by the original tech, but taken off the order by who knows?). Now they are telling me that the part that they should have ordered 2 weeks ago is on back order until sometime in May. All I am getting from Whirlpool is lip service and they honestly do not care one tiny little bit that I have a dryer under warranty that will not have been working now for close to six weeks. This is unacceptable business practices.For the record I bought the unit at LOWES and they too refuse to stand behind the product. Basically told me tough they have nothing to do with it. I also purchased an $8000 Kitchenaid (Whirlpool) Refrigerator 5 years ago and the control panel went out about 4 years later. They stopped making the part and I have to THROW away an $8000 refrigerator because they dont make the part for it. As evidenced above, Whirlpool products do not stand the test of time and when they do break (even under warranty), they cannot fix them in a timely manner or at all in the case of the refrig (not under warranty). I caution every reader of this diatribe to choose wisely WHERE you purchase your appliances and carefully select a brand other than Whirlpool (and its brand affiliates of Kitchenaid, Jenn-air, Amana and certain Kenmore products).

We have a Whirlpool top freezer that is a very basic model with no bells and whistles. It is over 20 years old and has had no major issues. Tears in door seal have occurred but is to be expected with age and use.

I have owned two different Whirpool washers over the last several years, and they have both been a very big disappointment. More than that they have cost me money, time, and peace of mind. The Duet was my first experience with a Whirlpool appliance. It was a front load that I replaced the water pump on twice and constantly had to take the front bottom piece of the washer off to clean the trap on. It had been taken off so much that the machine actually just fell apart. It also had some type of mold or mildew problem where it made the clothes smell. It was a constant headache.I was stupid and allowed a salesperson from HHGregg to talk me into purchasing the Whirlpool Cabrio washer. Another huge mistake. Again, cost me time, money and peace of mind. I have owned the washer for a COUPLE OF MONTHS, and the clothes that I have washed smell so bad that I cannot use the washer anymore. I tried to call customer service, but it is impossible to get any help because the lines were so backed up, I have not had the time to sit and wait for an available person. Not to mention there is an extensive process of pushing lots of buttons before you are put on hold to presumably talk to a human being. I assume this is because so many people are having so many problems with their Whirlpool appliances. It is not surprising. I bought a new washer, a GE. It is awesome!When I have the patience and the time, I will try to call Whirlpool again and see if they are willing to do anything about the washer that at this point is just sitting in my garage taking up space. I spent around $600 on a washer I only got a few months of use out of. When we moved it to the garage, we could hear water swishing around, which explains the horrible smell of the clothes. Once I started having the issue, I went online to see if this was an easy fix, and it turned out that LOTS of other people are having the exact problem, to the point where people are trying to get a class action suit going. Do yourself a favor and avoid the hassle of dealing with this company. If you purchase a Whirlpool washer, I guarantee you will be sorry. Trust me, I was stupid enough to do it twice. Hope this helps someone avoid the headache these appliances have given me.I will never buy Whirlpool again. And by the way, Maytag is made by as well as the following: Admiral (Canada), Chambers, Coovert (acs), Crosley (newer fridges, a/c, washers), Danby (8, Estate, Inglis, Ikea, Kenmore (see Sears), KitchenAid (4), Kirkland, Maytag Epic®, Roper, Speed Queen (Canada only), Sub Zero (undercounter ice makers), Whirlpool.

I purchased model #GI7FVCXWY01, SERIAL #KY4234335, and it arrived in Jan 2010. It is now going in the trash! Two repair companies came out and both told me the ice maker had issued a recall, but in reality, Whirlpool told me to buy the replacement part for $348.73 to fix their poor design! I called the 1-866-698-2538 customer service and so sorry is all you get! By the way, neither of the repair were willing to install the replacement part, as it takes too long to install and these compressors are never the same after the ice maker has these issues! Both repairmen said to trash the refrigerator. How sad that a $2500 refrigerator only last from Jan 2010 until June 1, 2014!!! I will never buy a Whirlpool anything!

Whirlpool over stove microwave/convection oven model GH7208XRY-4 - I purchased this top of the line unit in April 2012 for a vacation home kitchen remodel. It wasnt installed until June 2012 and stopped working in May, 2013 just after the warranty period expired. The problem was with the touch screen panel that went blank and the fan/light control switches also failed. This unit has only had light use since my wife and I are retired and use it primarily for heating tea/coffee. I contacted Whirlpool customer service and they graciously offered to cover the cost of replacement parts but I had to pay a service charge of $125. The factory technician said the whole door needed to be replaced since the electronics were not readily accessible so it took about a week to get the replacement door which turned out to be the wrong one and needed to be reordered. The technician finally replaced the door and the faulty fan/light switch. Within a month the fan/light switch failed again but was still under warranty so it was replaced for free. A little more than a year after the last service the touch screen control panel began operating by itself changing screens and beeping randomly. This was somewhat disconcerting but the unit continued to work pretty normally until my wife placed a small plate of leftovers in oven to be reheated for 1 minute. She walked away to do other things and forgot about the food in the oven until we noticed a strong burning odor and found that the microwave was still running some 20 minutes later and had turned the food into a black mass of burned food and the plastic cover was melted and burned.I contacted Whirlpool service thinking that the unit was under warranty from the previous service but they said the parts only carried a 90 day warranty and my only recourse was to pay for another service call and purchase another door panel for approximately $400 or I could buy an extended service contract for $300. Needless to say Im not about to spend that kind of money to, at best, get another year of service from this inferior product. This is simply not a safe product that could have started a deadly fire if I had not been present to stop it when I did. I have probably owned a dozen microwaves from other manufacturers and have never had any kind of problem including a comparable GE unit that has been flawless for over 15 years. I am extremely disappointed that Whirlpool has cheapened its product line to such an extent but I suppose I shouldnt be surprised since I noted this product was made in China.

I purchased a Whirlpool washer in March 2007. That washer is now leaking from the bottom. I called Whirlpool. I was told that the machine only had a one-year warranty, so repairs would be at my expense. The CSR then offered to schedule a service call for me at $139, which I refused. A few weeks later, I received in the mail an offer for an extended warranty on my Whirlpool washer.