I purchased it in 2011 for $1100 Canadian. Smooth glass top and true convection. The controls were easy to use, and understand. What bothered me was that it stopped working just after the warranty ran out. I did my research, and found that the newer ranges that have the controls on top at the back have issues with the motherboard overheating, and causing this problem. I did speak to Whirlpool customer service, and managed to convince them to supply the replacement part at no cost. I paid my local dealer to install it. This repair lasted for just over 1 year. Same problem again.This time I could not convince Whirlpool to supply the part. FYI The part in question is the controller. Essentially a motherboard. All the controls are operated through this small computer. It is the only replacement part that costs over $100. Last I checked it was around $450 Canadian. The reason for the fault is overheating. According to the tech that fixed it the first time, it is the most common problem with this style of range. I find this concerning considering the only thing a range does is create heat!Keep in mind that you are virtually held over a barrel. There are only two companies that market their products under multiple names adding up to over 80% of the appliances on the market. They battle for that market by offering more bells and whistles, and less quality. The Range I replaced four years ago was 20 years old. I just replaced my Whirlpool 3 months ago. I went outside of the 80%, and bought a Samsung. Im rolling the dice, and went with induction top. My theory is it will produce less heat because it just heats the pot, not the stove top.Low quality drives me nuts. I want fewer bells and whistles, and more long lasting reliability. I should be able to go my lifetime and only buy two or three ranges. We really like the induction top. It works fast, and doesnt produce too much excess heat. Dual zone oven is a good idea. We werent looking for it, but there was a deal on. The dual zone induction range was only $50 more than the regular one beside it. Now my wife uses it all the time. She will have cookies in one zone, and a casserole for supper in the other. True convection is the other must have. It does a great job cooking everything evenly.

Had the entire kitchen remodeled. We bought a Whirlpool Gold French Door refrigerator from Sears, did not buy an extended service contract. The refrigerator has NEVER made an ice cube. The water dispenser in the left door sometimes works, mostly not. The fridge freezes the food inside, temp. set at 41°F. The entire ice maker has been replaced, several valves have been replaced, a service company rep. tore the back off the fridge, found some insulation misplaced, said he repaired that. We have been very patient. Three repair companies have been sent out by Whirlpool, two said the refrigerator CANNOT BE REPAIRED. Whirlpool told me the only resolution is repair.Whirlpools Customer Experience Center is a joke, they do nothing but try to schedule another repair call. Tell you how sorry they are about your problem but do nothing to solve the problem. Carefully trained to give you the BIG runaround and nothing else. You never get the same person twice or the same city twice. Patients exhausted. Calling my lawyer. I would strongly advise anyone needing a new refrigerator not to buy a Whirlpool product. You should also check the list of other brands they make, there are several. I wouldnt buy them either. Buy a fridge made in Japan by a Japanese company. They get it right and know the Quality Process.

Whirlpool washing machine has always been reliable for me. I have owned 2 and they lasted me many many years. Its easy to use, and cleans clothes perfectly. My family is also a fan of Whirlpool appliances.

I bought a new whirlpool washer 12/15. In May 2016 it stopped spinning fast, clothes are coming out wet, still waiting for it to be repaired. Waited 3 weeks for a part, repairman came out today, it did not fix the problem. Now it doesnt work at all. Service tech said wait another week for more information. Called whirlpool. They offered me a $50 gift card to cover the laundromat. I paid $1200 for this washer. whirlpool doesnt care. I want a replacement. They said the warranty covers repair only, but they cant fix it.

I have had the Whirlpool Cabrio washer and dryer for the last two years. I HATE them. We purchased them from Lowes at a price point of around $800 each. What we expected and what we got were two different things. The washer was horrible from the beginning. It is impossible to wash a load of clothes without the UL unbalanced load indicator. It is impossible to balance a load. I have taken wet clothes out and put them back in with no luck. It takes hours for a load to finally wash. I have all but given up as I have been told it us unrepairable and too costly! Now the dryer has decided it will no longer dry clothes. It has never been a good dryer but now it takes at least 120 minutes to dry jeans. Do not buy a Whirlpool! I will never have another Whirlpool product in my home... RIP OFF.

Whirlpool N50T91-403 purchased in Mar 12 had an error code 4. I knew the water heater had a safety installed in it when I was working on the plumbing and allowed it to drain the hot water side down to 16% of capacitance of 50 GL. After the plumbing issue was resolved, I saw the water heater had shut off (thermal protection) but the switch wasnt tripped as far as I could tell. Knowing small processors can only remember anything if they have power, I removed the Honeywell circuit board and with my multimeter probed all of the capacitors contacting them both (-) and (+) and in reverse order. Doing this forces the IC to forget its codes because they require a small amount of voltage to remember them, usually powered by a small capacitor. I reinstalled it and voila! Presto! It works again.

Multiple issues with the Gold Series. Have lost two refrigerators full of food!!! First problem was ice on the back wall of the fridge. 2 years later refrigerator is not blowing cold air and it is only 4 years old!!! Terrible product!!

I had to re-arrange my kitchen and have my slider doors moved over a foot to accommodate this monstrosity. After about 2 years the icemaker and water dispenser died - had to shove a facecloth in it to keep it from making noise. The white color is very hard to keep clean. Overall, I would not recommend a Whirlpool brand refrigerator.

Whirlpool Cabrio - 6 Big Problems: I dont write bad reviews on anything but in this case, I feel I have to warn potential buyers. Ive owned this washer for more than 4 years. Here are the problems: 1) This washer TEARS HOLES in my towels; 2) It SHREDS some clothes; 3) Loads are UNBALANCED every time I use it, regardless of load type or size; 4) Very LOUD when running. My neighbors can hear it and they are 150 feet behind us. It sounds like someone is pounding on the walls of my house. BOOM! BOOM! BOOM! I havent seen it, but I believe it might actually be jumping off the floor; 5) Its NOT High Capacity as advertised. Sure, the drum is big, but you cant put much more than a tiny load in it. If you try a larger load, the clothes dont get cleaned; and 6) Whirlpool wont do a darn thing about it. They dont care about the buyer or their own reputation.Our family grew and I thought we needed a larger washer. I foolishly replaced a ten-year old, $300 standard top-loading GE washer that never had a problem, with this expensive **. The GE had a drum that was about 1/2 the size and it washed MORE clothes! The GE never damaged any clothes and it wasnt ridiculously loud like this one. I regret ever buying this expensive washer and I will never again buy a Whirlpool product.

I purchased a side-by-side Whirlpool refrigerator in May 17, 2010 from Lowes in Gilroy. After 17 months of service, the compressor went down this morning. I have called the service center and they cant give any help because it was over the 1-year limited warranty. More than $500 is good for just 17 months usage. Would it be worth it to have Whirlpool appliances? Do think about it before you choose a Whirlpool refrigerator.

Bought this because it was a Whirlpool product and liked how it was supposed to work at the store, HhGregg in Downingtown. Anyway one week in we started having problems, clothes not being washed well, and constant problems of dripping wet clothes, like they were never spun at all. Would have to readjust all the clothes, respin, most times we have to that that every time we wash clothes and have to respin more than once and even then, clothes have too much water left in them, so it takes forever to get our clothes dry. We have a service contract with Sears, we have repairmen out a few times. Get told, dont wash towels in it, only do very small loads, supposed to be a large capacity washer, nothing wrong with it. Now its worse than ever, terrible product. I want a different washer, its rusting at the lid, its only at the most 2 yrs old, it was expensive and am very, very frustrated!!! I want what I paid For!!! Whirlpool, shame on you for putting out such crap.On to my next problem with a Whirlpool range, again bought it because it was a Whirlpool. We had our Kitchen remodeled and the range I had was white. We needed a stainless steel range, Bought the Gold series AquaLift convection oven. This is the most horrible piece of crap. The convection oven does not cook as a convection should, food takes forever to cook on convection, reg feature works faster and hotter than the convection. In my old range I used the convection feature always unless I was baking a cake. Then used the AquaLift feature to clean my oven, it was not dirty , but I like a sparkling oven, so followed the directions, set it to clean. It looked the same after it supposedly cleaned the oven. Nothing was cleaned, tried it again, it was a little more dirty, something had spilled. I wiped out the oven, used the AquaLift self cleaning feature again, same results, old oven, self clean, the oven after a cleaning cycle, only ash was left, wipe it out, it was spotless. So I called for repair, the repair guy was here about 5-6 different times, tried this and that, replaced a heating element in the oven, turned the temperature up in the oven, so now when I bake, I have to figure out what temp I need to put it on. Tried that, even admitted that the AquaLift feature was a bust. I contacted Whirlpool, I want it replaced with a different model. This range is about I and a half years old, want to replace it but again was very expensive. Its a terrible product, it cant be a coincidence, that both newer appliances made by Whirlpool are terrible!!!! Combined they cost me almost 3000.00 dollars. I feel that I have been ripped off definitely did not get the great products that I thought I was buying. No response from Whirlpool, no satisfaction. I want them both replaced or my money back, take them out of here, they are useless!!!!! I will NEVER buy another Whirlpool product again, and have told everyone I know about the terrible quality of these products.

Purchased brand new washer & dryer that was chosen specifically for its HE & washing capabilities as Im a single mom with 5 kids, 2 of whom have disabilities, & I need a good washer & dryer. Washer and dryer both broke several times. I paid for an extended warranty but they never resolved the issue. Called Whirlpool & they didnt care. Four years later, Im using a set I bought used that rips my clothes while the washer & dryer sit still broken. Will never buy from Whirlpool or Kettles again.

Aqualift is a Joke. We recently remodeled our kitchen and purchased a new Whirlpool range model #WFE710HOAE. It came with a feature called Aqualift Technology to clean the oven. The button you push to start it says Aqualift Self-Cleaning. I followed the simple directions and when it was finished I was surprised to find that nothing was clean. I tried it again with the same results. I had to then clean some of it with the enclosed scrubbing pad. You cannot use any cleaners except one that they also send a small sample of. In short, it was like the old days cleaning my mothers oven with a scrub pad and a lot of elbow grease. I spent 30 minutes getting it somewhat clean. I am so disappointed and mad that Whirlpool can just blatantly mislead consumers this way. No one wants to buy an expensive product such as this and have to clean it by hand. You get as good a result if you do not even use Aqualift. My last range lasted 20 years and all you had to do was take a wet cloth and wipe out the residue. Whirlpool is at best incompetent and at worse criminal and purposely misleading with this and other similar models and should recall or be forced to recall and replace these with a working technology. I am surprised that the Federal Government has not stepped in. I would be very supportive and would participate in a class action lawsuit on this matter. As I stated in the beginning, this product is a joke.

We purchased a Whirlpool gas range on 12/3/11. It was to be delivered later that month and days before delivery we received a call the stove was damaged. They asked if we wanted it and could get it at a reduced price. We said no, we wanted a new one and that one was delivered on 1/4/12. This stove has had many service calls to fix the ignite for the oven. The ignite and a circuit board for this problem has been replaced many times. The smell of gas in the house is terrible from the many times you try to light the oven. This problem has happened many times when a family event was going to be done (Thanksgiving, making Christmas cookies). It is also very poor advertisement for the company and stove to have this happen when there are so many people around. They will have a tendency to spread the word by mouth. PS: When we called (12-13-13), the woman stated after 4 calls for the same thing there should be a replacement or a refund of money (All the calls have been for the same thing OVEN IGNITE and GAS SMELL).

Whirlpool Auto Load Sensing - I bought the washer in Aug 2010 and it worked well until the timer went out this year. Its only 4 years old! The repairman said it would cost $350 to fix - the machine cost me $469 to begin with! Whirlpool builds a poor quality product and Id advise people not to buy their brand of anything.

Purchased a Whirlpool microwave for new home in December 2013. Model WHM31017AW-1. This is the second time the heater element has to be replaced. Im starting to learn the warning signals: open door and then a short time later the microwave would die a sudden death. In my 20s I purchased for my house in Boca Raton Fl all Whirlpool products... they worked forever. Now not so much. In order to get this one fixed again, I had to get a service contract for $300 which would be cheaper than getting it fixed again, heating element $400 and service call another $100. Serious $300 service contract money too much for a senior citizen. Never will I buy another Whirlpool product as a result.

I purchased whirlpool Model# WFG540H0ES gas with convection. I purchased it because the price was $1000 dollars less than comparable ovens and even now the price has gone up $300 since I purchased it. I really wanted the luxe look at a discount price, a burner that you could lay a grill over, and five burners which it provided all of those things. I hesitated to buy this oven because the door fell off the last Whirlpool within three years and they refused to fix it so I tried not to buy this brand but it had the amenities I wanted for the price I could afford. I really like the oven. I like the oven the best because it really does make a great cake. I like the two large grates that sit across the oven. It makes it feel high end. If you dont wipe the range immediately grease gets stuck on the range and is hard to clean. This is what I like the least. Im ready to wipe on the weekend and its too late. It took me four days of internet comparison to decide on this one. The house is not painted, the cabinets are falling off the wall literally but I am extremely proud of this oven and it makes me feel affluent even though Im not.

I bought my washer machine because my other one died on me. I was nearly everyday so I needed a dependable machine but also good price. This machine is both and I would definitely recommend Whirlpool.

Bought the HE Whirlpool Cabrio in 2013 after having my old agitator Maytag for 19 years. After reading the other reviews I do not feel alone. An awful washer, a year after our purchase the spin cycle is so loud we have to close the laundry room door. Now it has been leaking into my basement. I called a repairman, explained my problem. He suggested to junk the washer, it will cost more to repair than buying a new washer. In addition my clothes did not clean properly, soap stains on clothes because it does not use enough water. This was about $1000 purchase that lasted less than 4 years! I am done with Whirlpool and suggest to anyone not purchase a HE washer, nothing like the old style agitator washers.

We purchased a Whirlpool French Door Refrigerator WRF989SDAHOO less than two years ago. The refrigerator runs constantly and has gotten louder by the day. It is so loud you can hear it when you are in another room. The temperature on the refrigerator is too cold and freezes fruit when I put it in. I contact Whirlpool online and they said it seems fine to them and also there is no temperature control that I can change myself. I am afraid I am going to come home one day to a dead refrigerator and spoiled food. I was not happy with their response and I WOULD NOT PURCHASE this again. The other problem is, we bought as a set, matching stove, refrigerator, microwave and dishwasher. So if I have to get a new fridge it wont match.

Two-year old Whirlpool Cabrio top load washer; absolute piece of junk! Bearing on the drum howls like a train. Now the master board or some other sensor (under drum) is out. Serviced for the third time and the service repairman states its cheaper to replace than to repair. For a 2 person household, it is reasonable for us to expect more than 2 years from a washing machine. Same experience with Whirlpool 15 years ago. 1st time shame on you; second time shame on me.

I purchased a Whirlpool gas top range from Lowes in Somerset Ky September 2013. Model number WFG524SLAB1. The surface is showing bubbles. I contacted Whirlpool and they gave some kind of story. In other words I am stuck with it. Still under warranty but they wont send someone out to look at it. Lowes told us that it could be a paint defect when it was made. If the top starts peeling, it will be a real mess. I have never used anything abrasive on the stove top. As of right now I am not happy with Whirlpool at all and if they dont do something about this, I will never buy another one of their appliances.

I bought my refrigerator side by side on April 16th 2010 at Lowes. Not even six months, the liner inside started to get cracked. I called and they send serviceman. He just put a tape to cover the cracks. I called Whirpool corp and they told me its cosmetics issue so our warranty does not cover cosmetic problem for as long it works and cools. I will never purchase Whirpool brands. Lesson learned.

This is a top loading, with agitator, purchased from Costco over five years ago. It took some time finding a top loader, which I will always prefer. Very reliable. Have only needed repaired once. Have other Whirlpool appliances, very reliable.. Fridge over 20 years old and no problems, except needing new ice maker. Also, other whirlpool washer we had over 15 years.

The water dispenser tube cracked and split off near the dispensing end, making the dispenser unusable. Not a consumer repair, by any means. Refrigerator is only a year old. I had a similar parts quality issue with a Whirlpool dishwasher. I will never purchase another Whirlpool appliance, and will advise all to avoid as well.

My washing machine ruined clothes with tiny rips. Small rubber pieces appeared in clothes. This happened during warranty but Whirlpool would do nothing. Finally, the bellow completely broke apart after 13 months. Repairman could not determine problem until this time. Whirlpool would do nothing.

I have a Whirlpool french door unit with ice & water through the freezer door. I recently noticed rust in the ice. When the extended service plans tech came to see it he told me that the ice bucket would have to be ordered. Almost a month later, I called him and was told that rust isnt covered. I understand that surface or cosmetic rust shouldnt be covered, but rust in a place where it can be ingested is different. Anyway, I called Whirlpool directly and a very nice phone rep agreed with me and asked her supervisor. Needless to say, I just sent Whirlpool a letter stating that I would pursue this through legal channels if I dont get satisfaction.

After just 22 months I need to shell out $300 for a new microprocessor. My Miele lasted for nine years. In the olden days washing machines could last for 15-20. Do not buy Whirlpool, from what I understand its a dying company...

8 cu. ft. Cabrio® High-Efficiency Top Load Washer with Steam - I bought a new washer. It did a poor job rinsing and spinning dry. Whirlpool customer threatened me that a service charge may be charge if the repairman came out and found nothing wrong. After calling three times I ordered a repairman out. The repairman explained that only way to prevent soap residue on your clean clothes is to use the bulky and deep water options. Also dont use high spin or when it spins your clothes dry, it leaves them in a tangled mess that requires ironing to remove the wrinkles. This washer is not ready for the market and must be removed until they can perfect it. It cost me $200 to return and exchange this model for the Front Load Duet, which works excellent. Whirlpool should be ashamed to have ever put this machine on the market.

Our fridge was delivered the 24th of Jan. We called on the 19th of June because the fridge stopped working. The 24th Capital Refrigeration came out and said he ordered the parts, they would likely be there on the on Fri. the 28th. On the 5th the parts werent in yet. On the 5th of July I called Whirlpool to find out whats going on and the parts were on backorder. They would expedite the parts. The parts came in the 12th. Our Whirlpool refrigerator was delivered on the 24 of Jan. It quit working on the 19th of June so we called Lowes. They hooked us up with Whirlpool. They sent a tech the 24th. He (Mike with Capital Refrigeration) left saying he ordered the parts and they would likely be in on that Friday the 28th. I call Lowes on Mon. the 1st. They hooked me up with Whirlpool and they said the parts were being shipped that day and should be to Capital Refrigeration on Fri. the 5th. I called on the 5th and now the parts are on backorder (they didnt know they didnt have the parts). So the parts came in on the 12th. Capital Refrigeration came out, installed all new circuit boards. That didnt work, still no fridge (he suggest replacing the fridge but Whirlpool says no). So he orders new parts. He comes out on the 17th and installed new parts (coils and stuff). It worked for 3 days and quit again, I lost my food again. I call Lowes again. They hook me up with Whirlpool. They say theyre sending a different company. On the 19th A1 Quality Appliance calls, set up appointment for 23rd. The come out and say they are ordering the parts on the 25th. They say that Whirlpool said parts would arrive Mon. the 29th. On the 30th A1 Quality said the parts arent in but they have us scheduled for Wed. the 31st. NO PARTS. I called whirlpool and now I find out again they dont even have the parts again (they dont know they dont have the parts). They are on backorder and in a week call them to see if they have found the parts yet.So at the end of a week (the 7th of Aug.) Whirlpool said to call and see if they found this part yet (maybe not). It will have been 7 weeks without a fridge that broke when in use less than 5 months. They have told us the parts would be here 3 times and then find out all these parts have been on backorder every time. The 1st repairman Mike at Capital Refrigeration advised to replace the unit but they are still dragging this out. They did send us $150 for the inconvenience (not for all the food we lost). It would appear it will be 2 months before we have a refrigerator again if we are lucky. Whirlpool is a very poor company that has misled us several times and are still doing so. We purchased their refrigerator, double stacked oven, microwave and dishwasher and are very sorry. They say they record the calls if there is any doubt about my facts.

Love the design and style. It is an above the stove built-in model. And love the combination of microwave use and to have the ability to also use convection. It certainly has been an excellent purchase and would buy it again and would strongly recommend it to anyone.

My wife and I bought a Whirlpool water heater NU50T121-403, SER# 0733323 as we researched online the best efficient water heater for the money... which was actually more than we budgeted for. We purchased it from LOWES and our Plumber had to return the first heater due to a huge dent on the outside of the body once it was removed from the box. LOWES replaced it, no problem and he installed it. GREAT, HOT water for about six (6) months. Pilot light went out and has continued failing after relighting numerous times! Now we have the four (4) blinks indicating that the Honeywell gas control needs to be replaced only after 27 months of use. Whirlpool offers 12 year warranty on tank & parts, but come to find out, not this part. We were both raised on Whirlpool products and thought we based on our parents successes of various Whirlpool products, we were buying quality brand. We were soon disappointed and will never buy another Whirlpool manufactured Brand again!!

Brand new dishwasher and first time I started it I noticed the timer showed the cycle taking over 3 hours. When done I opened the door and there was some water in the bottom and the door was very wet. Dishes had not been washed. A glass that had turned upright had no water in it. The soap pod was still intact. I started over again and the same thing happened - two more times. The silverware is not clean either. Its going back!!! Im sure there will be resistance but we will deal with it.

Whirlpool sent me a different part 3 times and hot water tank only work for a few weeks, then the pilot light goes back out. They never offered any more help.

BEWARE THE TEMP CAN BE 25 degrees off high and 25 deg lower and Whirlpool says that is within specifications. My oven temp was set at 350 and nothing was cooked... After 7 repair calls with their certified repair companies (the 2 worst repair companies that I have ever used) I was told that if you set your oven at 350 that if it stays in between 325 and 375 that Whirlpool claims that it is working fine and will not do anything. I called and talked to customer service and asked the lady that if you set your oven at 350 should it stay within a few degrees of that and she said YES.The people that work at Whirlpool do not even know what kind of junk that their company is selling. I asked to return it and get a more expensive model hoping that it would work better but they said that they sell ovens and do not buy them. Be sure to get in writing from your sales person that your oven will constantly hold the temp within a few degrees. I tried to do the Whirlpool survey but after 11 attempts they said that there was errors in receiving and they did not get it. If you buy Whirlpool then you did not ask the right questions. I WILL NEVER BUY Whirlpool again (unfortunately I have a Whirlpool dishwasher and refrigerator that are not much better) and if you do you will say the same things and be out Thousands like I am.

Whirlpool Cabrio - Worst washing machine I have ever had. Unbalanced when washing sheets, towels. It does not matter if one sheet or two. I will never buy another one like this again. I would be better off having a twin tub for the amount of time I spend in the laundry to fix this machine when it bangs, bangs because it is unbalanced. HATE, HATE, HATE it.

Ive had my Whirlpool water heater for almost 4 years now and for the last year and a half, I had to have the pilot light lit at least 5 times. I finally got so frustrated around the 3 times and called the company. They gave me instructions on how to light it and to ensure no draft was around the tank. A couple of weeks ago, it went out again and I called. This time I was told to replace the thermocouple. I did that and guess what? Still no hot water. Im a single parent with 2 kids and weve been boiling water just to bath.A service tech came out and told me I need to replace the tank altogether. I called Whirlpool service and they told me it was nothing they can do. Like many of you, I got this tank from Lowes and they will not do anything about it either. Its hurtful and stressful that doing a holiday season, I have to decide to either buy a hot water tank or give my kids a good Christmas. I know several friends and family who has had their tanks a lot longer with no problem. My problem is its a crappy Whirlpool brand with poor customer service.

My 3 year old water heater failed and the service line would send us the part but the install was my responsibility. Shipping was free but would take 3-5 BUSINESS days. Whole has a week to wait with no hot water, $35 for expedited shipping (which took 2 days), $175 for the plumber (authorized by Lowes (1star also) for installs). 2 days later the unit is cold again... Plumber comes back, plays with wiring and gets it fired up again. Says if there is a problem again to refer the techs to the plumbers office for new tank. Well now Whirlpool says they will only take the word of their own plumber AUTHORIZED HEATING 24 hours wait for a service call. You will be the 1st job Wednesday morning. Wednesday 930 call from AH we are backed up. Hope to be there between 1 and 4 pm. How did you get backed up if I was 1st job? Never again will I buy Whirlpool and nothing from Lowes as well. Still no hot water day 3 second time in 2 months.

I purchased a Whirlpool Microwave on 9/21/10 from Hamilton-Bryan in Wichita Falls, Texas. I had a small fire in my microwave on 9/19/11, due to a faulty mica board. This was replaced by Mr. Bobs in Wichita Falls, TX, under the warranty. Then on 1/9/12, the microwave would not warm anything. I called Mr. Bobs again, and they said the transformer was out. I called Whirlpool, and was told by Yvonne that Whirlpool would replace the part only, with no labor, but Mr. Bobs was closed, and to call back in the morning, so this authorization could be set up with Mr. Bobs. I called back and there was no record of my call with Yvonne. I talked to a supervisor Rachel in Tennessee. She put me on hold for a while and finally said she found Yvonnes note to authorize the part. I explained to each person I talked to that I was dissatisfied with Whirlpool. I believe I have a defective microwave. I would like my money back, or a new microwave. I believe the defective mica board is related to the defective transformer. I am a very dissatisfied customer. I have used Whirlpool most of my adult life. I have used them since the 1970s. I currently have a Whirlpool refrigerator, washer, and dryer. A similar situation like this occurred when I bought a Samsung washer. I was dissatisfied, and Samsung refunded my money, and I bought a Whirlpool washer to replace Samsung. I will not be satisfied with this situation, until the microwave is replaced. Thank you for your concern and attention to this matter.

I own a Whirlpool Cabrio washer, model #WTW7800XWO. The lid to the washer has completely detached for lack of a better word. It literally blew-off during the spin cycle and is hanging on by one hinge. My husband is disabled and I have had to go without using the washer for several days, waiting on a repair person not to mention the expense that will be incurred.This was a very potentially dangerous situation. My washer is barely older than one year. To add insult to injury, when I contacted the customer service department, I was told I would have to purchase and replace the lid or pay $299.00 for warranty insurance to have it covered because this is not considered a Quality Control issue.The service person has told me that both hinges and the lid will have to be ordered and replaced, leaving me without a washer for several more days. No one has been able to tell me why this happened. I fear this happening again after repair and do not feel safe with this washer. I would appreciate a response as soon as possible.

Ive had other brands of washers and dryers and I must say I always return to Whirlpool. They are well made and do what they are supposed to. Never had problems. My last set of Whirlpool was about 12 years old. Great product.

Cabrio washing machine WTW8600YW0 - Had this washer for 3 years. Its been repaired a few times, but this last time theyve replaced the bearings 3 times and it only lasts less than 1 week. This $1000 washer is now going on the trash. I tried to get help from WP, to no avail. There is a reason these are only warranted 1 year. One thing I liked about it: the fast spin speed gets clothes drier. Every other aspect is crap. Cleans very poorly. You cant make it use enough water. The tub looks huge because it doesnt have a conventional agitator. But if you put much in there you will end up rewashing in small loads because then it REALLY cleans poorly. I bought this because my trusted appliance store owner buddy said he owned one. When I asked him lately he doesnt talk much except admits that yes they have had a LOT of trouble with these machines. The life is very short on them. The wonderful fast spin speed destroys the light bearings quickly. And it gets worse the more its worked on. Its a disposable $1000 piece of trash. Im an engineer, and whoever designed this should have his degree revoked. The type of agitator it has and the extreme low water is very hard on your clothes. One zipper left loose will shred your clothes. I wanted to love the thing, but I have to hate it because it is unrepairable. If you could control the water and if it lasted at least 5 years without having to rebuild it several times at greater cost than it was purchased for, I might be less than rabidly angry at WP. They know they are junk but dont care. You have few choices as they now own most brands, and they know this. I have a Speed Queen on order. Just a plain old simple washer.

Whirlpool ADP100 wh. A few programs, washes well, dries ok, not great but ok. Standard free standing size, 60 x 85 x 59 cm. The washer itself is fine, but oh the cheap moulded plastic parts, utensil basket, water arms etc, so poorly made. Its amazing that a company would use such poor quality and design to save what can be a few cents on the overall product, personally I was disgusted at the cheap crappy plastic bits.

My landlord replaced our old Whirpool topload washer with a Whirlpool HE topload machine last year. Looks sleek, lots of settings BUT IT DOES NOT GET CLOTHES CLEAN - not on any setting, not if loaded as recommended or under-loaded, not if I use more or less detergent, and not if I follow all the tips for getting rid of residue. This machine so under-performs I have to spot clean my clothes AFTER I was them. And were not talking deep dirt or grime here, or things that need special treatment, Just ordinary dirt dirt, to which the machine adds gray streaks of dirty water residue. Thank God I didnt buy this turkey for myself -- I will NEVER buy one of these machines. I did two small rugs today and they came out dingier than they went in. These machines should be recalled. If I could give it less than one star, I would.

Stainless steel, easy to adjust, cools very well installed in a RV instead of standard RV fridge. Took a little bit of carpenter work to make Whirlpool fit but well worth the effort. The only problem I have with the fridge is that whirlpool wont honor the warranty because it is installed in a RV.

Purchased a new Jenn-Air JCD2295KES in 2007 when we remodeled our Kitchen. Its been a decent fridge. When it quit a couple of weeks ago, I had the repairman come. He informed me that the HV circuit board was bad and sorry but they dont make them anymore. What, a 7yr. old fridge and thats it? I sort of expect things to have to be repaired or maintained but to have to throw it away because Whirlpool chose not to carry the parts any longer. I decided to scour the net and see if I could find this legendary board. Lot of places seemed to have carried it but could no longer get it from Whirlpool. I found a place that could supposedly repair them but after a few days, they called and said the microprocessor was not repairable.I contacted Whirlpool and they gave me a place that does obsolete parts and although helpful, I thought they were real opportunists and wanted to charge me considerably more for a reconditioned board that a new one would have cost if I could find one. I kept looking on the internet to no avail and when I called Whirlpool again I was getting pretty upset. Here I am with a 7-year old refrigerator and cant get parts for it, thats just not right. They were pleasant but basically their stand was sorry, theres nothing we can do. I told them that I bought a lot of appliances as I have quite a few rental properties. I cant throw an appliance away just because I cant get a part. It just doesnt make sense. I feel Whirlpool/Jenn-Air simply doesnt care. Im not interested in their excuses, I just want parts. I dont think it is unreasonable to expect to be able to obtain parts for at least a dozen years or maybe even a little more.I posed the question to them. Would you buy a $2000 refrigerator if you knew it would only run 7 years? The customer rep. said no she wouldnt. Well, Whirlpool, neither will I. I was unimpressed with their lackluster response and offer of a $300 rebate on a new fridge. I can find better deals than that on my own. I have purchased many appliance and always actually liked the Whirlpool line but Ill not buy any of them again. Shame on you Whirlpool for letting your customers down. Just because you can ignore me, doesnt mean you should. Im in business and I would go to the ends of the earth for a customer to make them happy. No wonder the Asian companies are kicking butt on the so-called American manufacturers. If your not going to get service you might as well go for the cheap price.On a final note, I did after two weeks of searching find a board hidden in a little appliance repair shop in Colorado. It should arrive here tomorrow and was priced $150 less than the reconditioned board that the gougers Whirlpool recommended. I believe it is the last board on the planet. Hopefully it will get my fridge another 7 years down the road and by then Whirlpool and its subsidiaries will have been sucked up by foreign companies and under a different label.

This was the first new appliance that I had actually ever had and I purchased it in October of 2010. After four months, it started make a grinding sound. I called Whirlpool and the repair man replaced the motor. Approximately four months after that, the lid got stuck and the machine would not respond. Same routine as before, but this time the transmission was replaced. While the machine was apart, I noticed the white insulating panel from the bottom was brown in a spot and looked as if it had gotten hot. A month before the 1 year warranty expired, the washer started making an intermittent grinding sound nearly identical to the sound made when the motor went out. This time a different service company was sent out my Whirlpool and the said that nothing was wrong. Now, the machine is out of warranty and has stopped cleaning close and during the spin cycle the you can hear water running into the machine constantly. Last months water bill shows a 40% increase in water consumption when nothing has changed to incur a larger bill. Seeing all these comments makes me wonder why the heck nothing is being done to force recalls on such poor products. Consumers should be treated with a lot more respect than this. I will never recommend a Whirlpool product to anyone I meet. In fact, I will strongly discourage anyone who is contemplating buying a Whirlpool washer machine.

We purchased a Whirlpool unit Mod#WRF535SMBM from Home Depot in Bluffton, SC. Frost and ice build up in bottom freezer of our Whirlpool unit. We have had 4 service calls since our purchase of the unit in Dec 2014 (April, May, June and Sept) with one freezer door replacement due to a faulty door liner and soon to be a second freezer door replacement due to lack of insulation in the door, along with the door slides. Each service call visit is by a different service company. The other issue is the unit is advertised as S/S. This is the first time I have had a magnet stick to S/S so I figure that the outer shell is a mere coating of some sort and not a quality S/S product.

We came home from work and all was well. About an hour later, there was a strong burning smell in the kitchen, like wires burning. Sourced it to our refrigerator. Brought our grandson upstairs to the second floor apartment to get him away from the smell and possible smoke and/or fire. This unit has been repaired several times but not recently. After reading all the same reviews on this problem, we are definitely concerned that a fire may arise. Unfortunately we may wind up buying another, very expensive, refrigerator in the very near future but it will definitely not be a Whirlpool. I wish I could give Whirlpool a ZERO star because that is even too good for this company.

I purchased a Whirlpool French door fridge 6 years ago. In less than a year, it was not cooling and I was able to retroactively purchase an extended warranty which ended up saving me a ton. Less than 3 years later it had broken 3 times with three different part problems with a total down time of 6 months. Despite saying it didn’t qualify for lemon law, I was able to get it replaced after presenting all the facts. 3 years later, the new one is now currently experiencing the same problem and running a toasty 58 degrees and my food is once again in coolers on ice. Shopping for a different brand and I recommend you do as well. Whirlpool used to be a brand you could rely on. No more.

We purchased the Cabrio washer and dryer set 2 years ago (7/22/15) from Lowes and have HATED them since day one. The first wash in the washing machine left clothes dirtier than when they went in. Our clothes have never gotten truly clean. The washer has a HUGE tub which is what I liked about it so I can wash my King sized comforters. What a joke that turned out to be. The comforters only get half wet even on the deep water setting. The machine even left dark stains on my light colored comforter and ruined it. Fast forward to 2 years later and the washing machine stops spinning and fills with water clear up to the top of the tub and wont drain. I had to put the machine on the rinse and spin option to get it to drain. Tried a different setting and it worked for a few months but started doing the same thing. The washer seems to be unbalanced no matter what size load I do. I am thoroughly disgusted with this machine and wish I would have never purchased from Whirlpool. The dryer has always worked fine until recently (2 years after purchase). It quit drying the clothes and leaves everything twisted up and wrinkled, even if I take them out of the washer and shake them out before I put them in the dryer. Doesnt matter what setting I put it on, the result is the same. So now it seems as though BOTH of my machines only lasted 2 years. Im not going to bother fixing them, these will be used as target practice. I will never buy another Whirlpool product again.

This Whirlpool Cabrio washing machine just does not do the job. It smells inside and does not get clothes clean, just normal everyday laundry. I usually have to put them through twice. It is supposed to be a water save, but I dont think it uses enough. I use minimal he detergent, yet you can see detergent residue on the clothes after they are washed, I think because there is not enough water running through to rinse clothes very well.

Cabrio Whirlpool Washer - Bought this washer from HHGregg in Orange Park, Florida. This washing machine is horrible!! It does not fill the tub with water enough to even cover the clothes. Some of the clothes are not even wet. They just sit in dirty water, no agitation. Then it refills with water and the rinse water is dirty, there is no agitation or movement during the wash cycle. My clothes are stained and dried food and dirt are still on the clothes. My white clothes are now gray. This is the worst machine. I have tried everything. I am now hand washing the clothes and trying to add water to at least cover the clothes but the sensor just drains the extra water out. This machine is less than a year old. There should be a class action lawsuit against Whirlpool. I am not the only one; everyone that has this machine says it is a nightmare.

I purchased a water heater in 2011 and have had the thermostat replaced at least 5 times! Now, not only does the heater not heat the water, but it has rusted through and ruined my floors! They say they will replace the thermostat (oh yeah, yet another one!) but what about the crappy thing in the closet. I will NEVER buy anything that says Whirlpool on it. They dont stand behind their product and have made no efforts to correct the issue. There has to be a lemon law clause that would be applicable in here somewhere.

We purchased a Whirlpool Cabrio about 3 years ago. Have never really like it. It doesnt add enough water to the wash cycle unless you use the bulky setting, which fills the tub up the entire way, so wastes water. It would have been nice to choose your water level like you could on the old machines. Now it wont drain completely and wont spin totally. Ive tried using the drain/spin cycle 2-3 times extra and it still wont spin all the water out. Ive noticed that there is still water in the drum, you can hear it slosh when you move the drum, so I wonder - has anyone ever been told there is a filter in there somewhere that might be clogged keeping it from draining completely? My husband thinks that maybe all the water in the bottom of the drum is not letting it spin because its throwing it off balance. And yes, it stops before the cycle is complete and just sits there and blinks and you have to unplug it to clear the cycle. What a pain. We will never again buy a Whirlpool and I absolutely do not recommend Whirlpool washers. I have a Maytag as well and have not yet had problems with it. Bought it at the same time we bought the Cabrio (2 households). At least the water levels in the Maytag are a little more normal. You can wash more than 1 pair of jeans and get them clean in the Maytag. For those of you with the problem of the clothes not smelling clean - try running the clean cycle with a cup of bleach about once a week. No clothes in it - just a cup of bleach in the bleach dispenser and nothing else. Works for us.

My Whirlpool side-by-side refrigerator is just 4 years old. When they delivered it, they noticed damage on the bottom which required them to bring me a new refrigerator. The new one had issues with the ice maker that required multiple service calls to fix. The refrigerator door always seemed a bit misaligned as it was a bit lower than the freezer door, but it closed, so I never complained. I was just tired of all the issues! During the last six months, the door started to remain ajar instead of closing completely so that we had to always be sure to apply sufficient pressure to close it tightly. I considered calling in a repair, but it was still closing so I thought I might be overly critical. As it got worse, I realized the door was defective, but one day, it just fell off completely without warning as though the hinges were made of butter!After multiple service calls, a tech reattached the door, but I could see that it would not hold and sure enough, it is starting to remain ajar again. I have contacted the warranty company who is now saying the service tech claimed we were hanging on the door. This repair company the warranty company uses has an F rating with the BBB. Now, Im being told it may take a couple weeks to get another repair company to give them an opinion, but the issue is clear, the door was defective and it looks like they found a way to avoid having to make good on the warranty!

Apparently, Whirlpool selling all their rejected faulty washing machine in the market. The trick they are playing is the machine being sold with one year parts-labor warranty; They wont replace these machines with a new one because they know that these machine will never work, consumer will buy the faulty machine, obviously it wont work so consumer will call for service. The service guy will say that “oh! Machine needs a part and then the customer service will say “the part is being ordered”, “wait”, then the service guy will come with the part and after wasting some time he will say “Oh! The machine needs another part, and again customer service will tell the consumer that “you keep calling us”. One year will be gone! Bottom line – faulty machine is sold, Whirlpool made profit, buyer is robbed. I am one unfortunate customer who purchased Whirlpool Washing Machine which never worked as it is a faulty machine which should not go to the market at all; Whirlpool made money on my hard-earned dollars and I been robbed.

This product is not even worth 1 star mark. Like everyone else the Whirlpool Cabrio top loader does not clean clothes well. It leaves streaks of dirt and lint. It does not agitate well at all and does not put enough water to the point where some of the clothes dont even get wet. I had a repair guy that was selected by the warranty company to come fix it and we were told that this is a problem with the machine and there is no fix to it. I am now stuck with a $500.00 machine that doesnt clean clothes. Hopefully Whirlpool will have so many complaints they will at least find a fix to this machine. In the meantime dont waste your money like I did.

I purchased a Whirlpool refrigerator in 2012 and now it does not work and Whirlpool says a 1300.00 refrigerator only has a one year warranty. Please do not purchase a Whirlpool brand because they do not live up to their brand name.

We had to buy a new fridge in 2000 because ours broke. Following consumer reports, we went with a side-by-side Whirlpool gold and was it pricey! Within the first five years of its life, we had to replace the fan twice...the bar that separates the fridge and freezer could have fried an egg--it was so hot! When I had to replace it the second time, I pitched a fit to Whirlpool and they could care less! Now I see that the inside wall of the fridge section has cracks forming! I know the average lifespan is 10-15 years but I still will say that I will not buy from Whirlpool anymore! Their stuff is very expensive and it just seems it has too many small things that do not hold up!

Called Whirlpool customer care for help with identifying make and model number of a slide-in, ceramic cook-top range (one of their popular brands). The representative was cordial, patient and very helpful when it came to giving me directions on how to locate make/model information on the unit. That was until I let her know about a recent problem with the stove. The edge of the cooktop is much too sharp! My hand got cut while wiping down the stove top/adjacent counter. Although Ive had the stove for a while, Id never had that happen before; thats probably because I used a thin rag this time around to do the cleaning. I asked the rep if anyone else had reported getting cut by the stove top. She said, No. I let her know that my goal was to just them know about the situation, because such a sharp edge on a cooktop is a safety issue. She disagreed. But what could or should she have said? In all fairness, it came down to balancing loyalty to the company with genuine care for the customer.I do appreciate how kind she was in communicating with me, but am very displeased that once Id shared about the problem she seemed rather dismissive of the situation. How could the risk of being cut NOT be a product safety issue??? If you visit the Consumer Products Safety Commission website, you can see where risk of laceration is a reason some products are recalled. Based on that understanding, I would say that sharp edges on a ceramic cooktop IS a safety issue!

BUYER BEWARE!!!! Dishwasher less than 2 years old and pump & motor assembly went out. You would think and hope that an appliance would last longer than that... Contacted Whirlpool and they were not helpful at all. Will not be buying anything made by Whirlpool again...

We have had nothing but problems out of our refrigerator in the past 5 months. We purchased it a year ago in April and they have already replaced 7 parts on it. It still doesn’t freeze, and we have no ice... We will NEVER buy another Whirlpool product ever again!!!

I was gifted a washer and ventless dryer for my condo. It takes a little longer than a regular dryer but it works great. It fits perfectly in a closet.

Ive had this dishwasher for years and never a problem. My dishes are always clean and this dishwasher dries my dishes completely in a very short amount of time.

I just purchased a brand new home. I have an electric wall oven with the microwave over the oven. They are both built into the wall. Can anyone tell me why a massive amount of steam is coming out. It is really bad it makes my microwave glass so bad I can see through it. It is also making my cabinets so wet I have to use a towel to dry them. Plus I got a steam burn. Can someone tell me if this is normal.

Switched to bottom freezer and love the size. We all use and enjoy the filtered water. Whirlpool has proven to be a manufacturer I will always consider when making major appliance purchases for performance, service, and dependability.

My husband AND I purchased our Whirlpool Cabrio washer and dryer from Lowes in 2011 (Model # WTW7800XW2). About 10 months after I purchased this I noticed a hairline crack on the right side of the frame that holds the glass top near the hinge. I didnt think to much of this. I figured it may have been screwed to tight when manufactured. A few days ago I noticed the lid wasnt sitting flat and saw the crack had gotten much worse. The Cabrio lid is made with a heavy piece of glass inside a plastic frame allowing you to see through the top. Its pretty obvious that the plastic frame is not durable enough to hold the heavy piece of glass.I called Lowes and they told me that because I didnt purchase their extended warranty that I should contact Whirlpool. I called Whirlpool and was told it was a cosmetic defect because the washer still works. They also told me my washer is outside of its warranty so they would schedule someone to fix it but I was 100% responsible for the repair costs (which I found out will be $400). Out of curiosity I googled this issue online and found numerous people complaining about this exact same issue. When I told this to the customer service agent at Whirlpool, she said there werent enough people to recall the product. Why should I spend $400 when it was a design flaw that caused this problem? I found out the year after my washer was made, the lid was redesigned with a much sturdier frame, Coincidence? I think not!I havent had any problems thus far with the dryer but with the experience Ive had with this washer will make me never by another Whirlpool product again. I cant believe they wont stand by their product! Obviously they know this has been a major complaint on this model from 2011 because it was changed the following year. I have purchased many Whirlpool appliances over the years but dealing with this issues has been frustrating. Im so disappointed in Whirlpool and their lack of integrity!

I purchased this Whirlpool washer (model WTW7600XW2) on October 2011. Fabric softener dispenser is full of water at end of cycle. Repairman has replaced parts three times, but the problem is still not corrected. Today, I talked with a Whirlpool supervisor. She says this is normal. She told me to take the cup out and empty it. The cup is not removable, so she said I could blot it out with a cloth or sponge. I paid $800.00 for a washer with an automatic fabric dispenser that I must empty manually. I have used whirlpool appliances for 50 years of marriage, but this is my last one. I am very disappointed with customer service.

I purchased a Whirlpool side by side refrigerator in Jan 2014. The first thing I noticed was the installers bought the appliance in without a box. The next thing I noticed was the door would not close unless you gave it a big push. While looking around at the hinges, I found 2 hairline cracks at the base of the refrigerator and 2 dents. I called Service and they sent a technician out. The technician told me they are going to want to epoxy this and you will see it. They asked did it get delivered in the box, I said no. I asked why, she said it should have been delivered in the container so you would know that it is new and not a rejected one from a customer. I called Whirlpool to voice my issue with having this epoxied. Kecia was the CSR...she said that is the normal repair for a crack. I told her I had a Kenmore refrigerator for 23 years and it was still functional when I bought this. I replaced it to get the energy savings. I told her I wanted the refrigerator replaced. I told her that the cracks tells a story about the quality of the appliance. I asked her what happens if these cracks expand after the year warranty expires. She said you can buy the extended warranty. I said but the existing warranty will not cover the cracks...what will the the extended warranty do? I asked if there were any recalls...she said no. I asked have there been similar complaints about cracks and dings (not that I thought she would answer yes). She said no unless someone had stepped on the base of it. I told her I lived alone and I definitely did not step on the base of the refrigerator. She got aggravated (almost to the point of being rude) and said Mam, no one said you stood on the base. I asked her repeatedly if there was someone else I could speak with. Her repeated answer was I am authorized to speak with you. She wouldnt let me to speak with anyone else. I am done with Whirlpool and stuck with this substandard refrigerator. Not happy at all in Va.

My front load washer doesn’t get my clothes clean. I have to rinse twice and still there is soap in my towels and they smell bad. I’ve followed all the tips without much luck. Now I use only Oxyclean and rinse with 1/4-1/8 c vinegar. The machine doesn’t pump all of the water out of the machine either. To me it is low-efficiency!

This 29.5 cu foot fridge will not keep a steady temperature and it has had 5 Warranty visits in its first 3 months since new. It has had several Large components changed out including the Freezer door, water valves, electronic boards, gaskets, and more. I was NOT able to get it labeled as a lemon and returned to Lowe’s simply because I accepted Warranty work to be done in the first 30 days which then disables any chance to return the unit. If I had asked for it to be returned in the first 30 days with the First bad issues I could have. Now I am stuck with it and I dislike the fridge and will never buy another Whirlpool or any other appliance from Lowe’s.

Purchased a Whirlpool water heater (model ND50T122-403) through Lowe’s in Dec 2013. Later discovered online it fraught with breakdown issues. 11 months later ours broke down. Whirlpool Customer Service first told us We dont have any authorized plumbers in your area. Went to Lowe’s the next day - they called on their hotline and we got a call back from Whirlpool that afternoon. Told us part would ship out immediately (arrived next day - no complaints there) and gave us an authorization for 2 plumbers. Both are over 35 miles away and one is out of state. Called once the part arrived... First one said hed try to get to us in the next 4-7 days; second one said We get to warranty work as fill-in work. Well put you on a list and call if were going to be in your area. While we did a bit of web research before buying this water heater, we really should have taken the model number, gone home and googled it before buying. Wish wed gone with a unit from a real plumbing supply place. They were a lot more expensive but you get what you pay for.

The Whirlpool side-by-side had the space and durability we had hoped for in the price range we shopped in. It lasted longer than the refrigerator it replaced.

Cabrio Washing Machine - I purchased my washer and dryer in May of 2008. I had problems with sheets, towels and pants getting very twisted and tangled, but I just attributed that to a design flaw. My problems really began in January 2013 when loads were not level all the time. It didnt matter if it were 1 shirt or a load of towels; you had to stand by the machine and it took forever to finish a cycle.On 1/11/13, the first repair was the rods that kept the drum stable. $260.82 later, it worked again. On 2/16/13, the washer quit working. On 2/18/13, the repairman was back out. It needed a lid lock switch. It was $87.14 that time and he would be back when the part arrives ... There was still no washing machine. On 2/21/13, he returned with the lid switch and replaced it. That was $178.04 but wait, there were still other error codes so there was no working machine.I refuse to pay anymore as I now fear I will be buying a new machine after spending over $500 in less than 6 weeks, but Whirlpool did the right thing when I called and they agreed to repair the machine. They wanted a different company to come diagnose the problem (the machine gave an F50 and F51 error code to the repairman here on the 21st), so I have to wait for another repairman to come and look at the same codes flashing on the LED readout.On 3/1/13, the A&E repairman that Whirlpool sent out arrived at my house. I have been without a washer since the 16th of February. He diagnosed the problem and said that it is a $1,000 repair! I called Whirlpool and asked for a new machine, instead of throwing more money at this one. They informed me that if I didnt like their offer, they wont do anything then. I agreed to the repair.Parts started arriving at my house. On 3/13/13, another A&E repairman came out and started to fix the machine. He informed me that there was more wrong than the first guy thought, but he had the circuit boards so he would get it going. On 3/24/13, the washer quit working again and was flashing an F51 error code. This is the biggest piece of junk I have owned in my life. I have missed 5 half days of work since January and there is no end in sight. Why is Whirlpool allowed to get away with such an inferior machine?

We bought the microwave new after the 2011 flood where we had lost everything in Tennessee. I wanted to get Whirlpool appliances in the kitchen so all appliances were replaced. We bought a Whirlpool model WMH1163XVU-1 microwave; the unit will run but doesnt heat. I also called Whirlpool and with no regard to customer service at all even with all the complaints... This saddens me because I will never buy a Whirlpool appliance again and my grandparents only believed in them... With all the complaints, the attorney generals office should do something for the people.

I purchased both the Cabrio washer and dryer because my dryer stopped working, it was old, and I knew that soon the washer would too, and wanted to modernize my set -- it was my moms old set. I was thrilled to get it delivered and should have had the delivery man from Lowes take it right back, when he told me they had just come from picking up one from another lady who was thoroughly dissatisfied with hers.Well, it didnt take too many washings for me to understand why that lady was upset! I really wish I had done the same thing! EVERY load of dark clothes have to be wiped off to get off the disgusting wet lint thats all over the clothes! Thats been going on since DAY 1! In every load, the clothes do not get completely wet and I thought I had combated that issue by having a pitcher of water always available to pour onto the load, so the sensor will add more water... That doesnt work, I now see!!! I just noticed last night lots of wet lint was on my fabric shower curtain liner, and I was thoroughly upset! I just never feel as though anything I wash gets clean. I truly wish I had come across this site BEFORE I purchased my set, and I would never have done so. Is there ANYTHING that can be done for people who have purchased these horrible appliances?

I purchased a Whirlpool Cabrio just over a year ago. The washing machine does not clean clothes! While under warranty, a service tech came out to look at it. After hearing the problem, he replied that it was a common complaint and that he could not fix the machine because the problem was that it is so poorly made that it simply does not work. His recommendation was to come to terms with the loss of a thousand dollars as Whirlpool would not rectify the problem.Whirlpool really showed their true colors when they refused to cover the repair tech visit. Whirlpool supervisor Kitty explained to me that customer advice was not covered under warranty and that we would have to pay the bill. Highlights of her argument were that we should just rinse the clothes multiple times and they would eventually get clean. She also mentioned that if the machine really did not work as described, we should have complained sooner even though it was still under the one-year warranty. Whirlpool will sell you junk backed with horrible customer service. Beware!

Whirlpool Hot Water Tank Thermocouple - This is the third thermocouple we have had to replace on this hot water tank in the last six years. Granted the part isnt that expensive, but the service call and replacement have cost us dearly. This is faulty tank and Whirlpool needs to recall this tank and replace them with new tanks. The price of this original tank and replacing this thermocouple three times has cost us over $800.00 total. I am not sure angry is the right word to describe our dissatisfaction with Whirlpool.

We installed this furnace along with a matching 4ton a/c unit over four years ago. It was installed with a 3 zone computer controlled damper system to separately condition the three floors of our home. This furnace was ideal because it has a dual stage combustion chamber depending on how much demand there is. So besides being 95% efficient, the furnace can run at 70% or 100% heating capacity which saves on utility bills when the whole house doesn't need heat at the same time. It also had a variable speed blower which made start ups and shut downs almost unnoticeable. The blower actually ramps up to speed discreetly and adjusts itself according to the amount of back-pressure it senses. This allows it to respond to varying conditions as each of the 3 thermostats are calling for heating or cooling at different times. And yes here in St. Louis we have had days that require heat on the first floor and a/c on the third floor at the same time. The controller cycles between the two every 15 mintutes. All of these features make it ideal for our 2200sq ft three story brick home(four including the basement where it is installed). This furnace and control system along with new ductwork and dampers were able to replace the two old furnaces and a/c units originally in the home. We haven't had a single problem with it in over four years and would recommend Whirlpool Gold products to anyone I know. If I ever had to do this again in another house I would do exactly the same thing with exactly the same products.

I have used my Maytag washing machine weekly for the last 11 years... Never a problem. Just a well made, basic machine to wash clothes thoroughly. It does not have all the bells and whistles some of the newer models have, but it is a washing machine, not a video game.

I purchased a Whirlpool washing machine (model: AW01D8810 S silver color) and a Whirlpool refrigerator (model: WBM329 TI) together from United Arab Emirates for Dhs 1999/- & Dhs 1199 /- respectively on 28 Jan. 2011. I sent this machine to my hometown (India) in the same packing and I used the washing machine only for three months and found a complaint. I informed this to service center in Trivandrum, Kerala. Their team came to my home and told me that warranty cannot be given as I purchased machine overseas. They added that the PCB for the machine is having complaint and they dont have stock in India. Also, the machine is no longer available in the factory. The Whirlpool company completely stopped manufacturing the abovementioned model. Again, I came to UAE and contacted GEC group of companies for the PCB part. I got a quotation for PCB Dhs 425/- but the items is ex-stock with them. The machine cost only Dhs 1999/- and if I spend Dh425/- only for PCB, and the machine is with me for the parts since one and half years. I dont know what to do. If I spend another Dhs 600 + this PCB cost then Id rather go for another new branded washing machine. The model of machine is AWO1D8810S and serial no. is 12 nc 859247463000 003. Please advise what to do or if I can find the PCB in Kerala. What will be the cost? I am ready to pay the money for PCB but not for the above rates. Please advise, sir.

I purchased a (second) Whirlpool washer (WFW87HEDW0) in October 2014. Since purchasing (and to this day), I manually dried the rubber gasket after completing my daily washes, knowing that mold growth was possible. I wash one to two loads of clothes about three to four days per week. During the first year, I did not notice any mold in this area and was confident that the manual drying and cleaning with Affresh was preventing mold growth. However, at the beginning of this year I discovered a little mold growth, which has slowly been increasing, in the inside lower lip of the rubber gasket. The image attached reflects mold in its current state. I was very surprise to see this happening since my diligent cleaning has been thorough and never ending. I even remove the soap dispenser tray to clean and air dry it outside of the washer and leave the washer door open at the end of the daily washes for extra fresh air circulation. This is my first official complaint about a Whirlpool front loader washer, even though I previously owned another (GHW9200LQ0) before this one and had mold growing on the rubber door gasket but, unfortunately, never officially complained about that old machine. Now, I dont qualify for the $500 compensation because I never officially complained three times within the first five years of owning the old washer. To my dismay, I did not immediately realize I had mold growth in the old washer. It was only until years later that a repairman told me that I had mold growth in it. In addition to telling me the price of replacing the rubber part and replacing a broken water pump plus labor would cost as much as buying a new washer. Before purchasing a new washer, I researched and read many reviews about Whirlpool and other brands before deciding on this new Whirlpool. I decided to give Whirlpool another chance and to follow their recommendations on the proper cleaning of the machine. Once again, I am disappointed and angry with Whirlpool and, now, have to figure out what to do with my current situation.

My Whirlpool Cabrio washer (WTW6600SG2) is a money pit! After reading all of the nightmare stories concerning this washer one would think Whirlpool would offer a recall and try to correct their wrong doing. Do not buy a Whirlpool Cabrio. It was the worst decision I have ever made! Whirlpool does not stand behind their products. I cant believe they can get away with treating their customers so unfairly, taking their hard earned money for crap like this, then not offering to help after so many have had issues. The Cabrio is loud, doesnt get clothes clean, and is always flashing UL for uneven load (when it works at all). My local repairman has made many trips to fix my problem Cabrio. This time he is at a loss. Ill be buying a new washer and it will not be made by Whirlpool! Please, if you are reading this be forewarned!! You will regret your purchase if you buy a Whirlpool Cabrio.

I bought this washer (Whirlpool Cabrio) about 4 years ago. A year or so later, it started leaking; based on reading the troubleshooting guide we found that this was because the feet would continually get out of balance. After painstakingly re-leveling the washer every 6 months or so the washer now consistently leaks - even though its balanced/level! $508 to repair a machine I paid $787 for. No thanks. I agree too with the other reports that it doesnt get clothes clean. I just figured this was a feature those of us got for trying to be energy efficient.

In open concept homes, manufacturers need to consider the refrigerator’s noise — ice makers included. We hear every single clink and buzz. We love (and prefer) the french door concept, but the freezer drawer, when it’s fully loaded, is difficult to open and close. Also, the stainless steel scratches WAY too easily.

This product deserves ZERO stars! I purchased a Cabrio washer - dryer in October, 2013. I have carefully followed the instructions for the washer. I am hugely distressed about the large amount of money I spent on a washer that is absolutely terrible, horrible, awful., no words can adequately express how bad this so-called washer is. The low-water washing has torn up all of my new towels in the matter of a couple of washes. It has completely ripped out the hems of the towels and pulled long ragged strings in the towel. And these were not cheap towels. I am mad at myself for not researching better before buying. I hope my complaint can save another consumer from the misery I am suffering because of this shameful product.

Purchased a GGE388LXS04 electric range in June of 2013 from Lowes. In September 2013 one of the top burners went out, under warranty Whirlpool repaired the burner. Now after attempting to use the self cleaning mode for the oven, the ovens (top and bottom) along with warmer device do not work at all. This issue is evidently a major issue with Whirlpools electric ovens. Will call Whirlpool tomorrow as the oven is still under warranty, will also call Lowes and see if they will replace the oven with an oven with a comparable brand. Wish I had read this site before we purchased this oven. A very bad experience.

Whirlpool Cabrio - good consumer rating. Ive had it for 2 years. It does not clean well and the clothes does not smell clean even though I often clean the washer and leave the top open when Im not using it. Ive also had it service 3 times because the rotator keeps going off and makes a lot of noise. I bought an LG dishwasher for $1300 and it lasted 7 months and completely broke down less than a year and had to be replaced. After I bought a $400 Whirlpool. It does the same job and Ive had it for 2 years without any repairs.

We bought our Whirlpool Cabrio 7 years ago and it was great at first. I have not had any trouble with it ripping clothing. The clothes are clean. Its constantly breaking down. First it was the drain pump. Then the main computer board went! I called Whirlpool and of course the lady says its not covered. I had back up though. Google is amazing! I asked why this wasnt a recall as all over the web, people had this same problem. I pushed and pushed and she put me on hold. Came back to say it was in fact covered. What? Really? What changed your mind? She wasnt allowed to tell me. Supposedly had something to do with the date of manufacture. So okay, they send the repair guy out, its fixed. Now tonight, the lid locks and nothing happens! This repair was about 6 months ago. Grrrrr. Its been one thing after another with this hunk of expensive junk. When I buy an appliance I expect it to be problem free for far longer than this. I am not getting a code or anything, just dead air. So frustrating with three kids not being able to do laundry when I need it randomly :( Has anyone else had this problem? The lid locks, then does nothing. I unplugged it, pressed off and restarted it. Changed settings. Nothing is working.

I purchased this machine in February 2019. The standard one-year warranty covered the first service call less than one year later. This call was related to the main control board. If this part goes out it will prevent the washer from advancing through the cycles. A technician was able correct this problem by resetting control board. That was sometime the first year. The next call was for the same problem and it cost me $90 to have a technician reset the board again. I then learned how to do it myself through online research. However, I had to do it more regularly and this got old as you can imagine. I did buy myself about two months of time by purchasing a used part but it soon failed as well. This main control board cost $564 if you get it from the manufacturer. This exceeds the cost of the machine. It was purchased in 2019. (The same machine has gone up to $740 today.) I had no other problems with that appliance however, it appears nowadays with electronics taking over cycles vs. mechanical parts you will not enjoy the same longevity as I did when I got 16 years out of a GE washer before this one. I have replaced this machine with a competitors product that costs less than the part except for the 5-year warranty from Lowes.

I am completely dissatisfied with the competence and accountability that I have encountered while dealing with Whirlpool Canada. I ordered a Whirlpool Refrigerator in September of 2011. I opted to switch the door swing myself since it is a relatively simple task and of course they charge you extra if they do it for you. Once I had the door installed, the last step was to screw on the handle. The door was missing the threading which allowed the handle to be installed. I contacted Goehmans to set up a service call. They looked at the fridge only to tell me that they needed to order an entire door. A month and a half later I had not been contacted by anyone regarding the whereabouts of the replacement door.Long story short, over four months later and after hours of phone calls recounting the details of the events numerous times to numerous employees, all Whirlpool had to say over and over again was I understand, but unfortunately we do not provide any compensation.” They said that the warranty only covered repairs and not product replacement, which would be fine if it ever broke but they delivered a fridge that was not built correctly in the first place. They took no responsibility for the lack of quality control.After speaking with the supervisor Josh, and insisting that we be compensated for the inconveniences and frustration, he finally agreed to extend the warranty by 3 months. I told him that they should offer a year extension since if they stood behind their product that it wouldnt even cost them a cent. He politely told me that he understood and what email address did I want the extended warranty information to go to and that he would offer only the 3 month warranty. When I received the email, I found out that I had yet another phone call to make in order to engage the extra 3 month warranty.I am extremely frustrated with the level of service and I feel as though they school their employees to be therapists that offer no solutions. They were all very willing to listen and offer a sympathetic ear, tell you that they understand but not to take action or offer a solution. They seemed to think that it was acceptable that I pay them full price for a fridge but not deliver the full appliance for a projected 6-8 months. In my book and to most consumers, this is not acceptable. When I pay full price for a product, I feel that a full product should be delivered to me in working order. Whirlpool got their money and the special order door seems to be at the low end of their priority list. How else can they justify a 6-8 month wait for part replacement?Somebody please sell Josh a car with no stereo system, make him pay for the option and see if he if he thinks waiting 6-8 months for it is acceptable. Oh yeah, and waste 6-10 hours of his personal time trying find out where the heck his stereo system is then tell him how much you understand. I guess I can stroke Whirlpool off as a brand of appliance for any future purchases.

I have been given a runaround for over a month to get my refrigerator fixed. They gave me a defected piece and it broke down in less than a year. I have been calling them up every day and they put me on hold forever-then they ask for all the details and direct me to another company. As of right now I have not received any help-My family is really frustrated as we have no fridge all this time. I dont know what to do.

We purchased our oven on 12/06/15. I have called and complained about the AquaLift oven on more than one occasion. This technology does not work. I would have thought that there would have FINALLY been a recall on this oven. I am a senior who thought this stove would last me for the rest of my life. I have to stand on my head to try to clean it. NEVER, NEVER, NEVER would I have purchased this if I had read any of the reviews. Buyer beware!!!

I have had our Whirlpool Cabrio washer and dryer (CU0771356 and MU0803512) for four years. Our trouble started when the machines were 14 months old. The numerous error codes have been fixed by replacing boards, the bearing has went out, and the entire tub has been replaced. The dryer has had two service calls for going out. Now, both are out again. The washer pump is bad and the dryer has stopped heating up. Where is the class action lawsuit?

We have had this water heater for less than 5 years. It was purchased new from Lowe’s. This is the second time we have had to replace the thermocouple and are told that we have to order the part from Whirlpool. Really? What do we do for hot water in the meantime? This is a very disappointing response from Whirlpool and Lowe’s. I will never again purchase anything from either company. We had to buy a new heater today, pay for installation and permits. This is a rip-off by Whirlpool and Lowe’s.

I have Whirlpool fridge for a very long time since I own my house and for me is one of the best, is a great company and occasionally have to fix in a couple of times and afraid to buy another more modern and not last like this old fridge.

It works quite well except if you put items in the back of the top shelf of the refrigerator it will freeze them as if they were in the freezer section. I have a bottom freezer and that works quite well. And it is very quiet when running.

Purchased a Whirlpool dishwasher less than 3 years ago. Absolutely horrible! The LEDs stopped working on the control panel within the second year. A few months after that the heating element stopped working. Replacing the element and thermostat did not help. The warranty only last for a year, and now I know why. Whirlpool does not stand behind their products and they were completely unwilling to help, and were quite rude honestly. I will never buy a Whirlpool product again!

I am a Whirlpool Privilege Member - IFB privilege number **. This is Mrs ** here and I possess two Whirlpool Fridges, one single door and one double door (Elite Model). In fact, all my family members have Whirlpool refrigerators because I recommended them and because I have had a very satisfying experience with your service until now.I recently (first week of March) logged a complaint as my fridge was not working (it was working on and off). The Mechanic from the service center visited us and said that the compressor was at fault. I had some doubt about this as the Fridge was working on and off and I requested my friend who had a workshop to come and have a look. He checked and said that the compressor was working perfectly but looked like there was some problem in the supply of current which could be a loose contact or something.So I logged another complaint and when the mechanic came (this time a different one), I was out of the country and my husband was there in the house. He checked the fridge and said the compressor was working and apologized for the earlier mechanic’s wrong diagnosis. He also said that it was difficult that since the wires were inside the beading or the Puff, or whatever, the fridge could not be repaired.I am really astonished and pained by this comment by the mechanic as we spent a lot of money and bought a fridge for its brand worth name. I shudder to think if this complaint had happened two years after I brought it, should I simply throw the fridge because it cant be repaired? Is there anything at all where the company can say it can’t be repaired? Are fridges used and thrown in India? I am all the more worried because I have been recommending Whirlpool Fridges left and right to everyone and I tell them that there could be a situation when Whirlpool would ask you to simply throw your fridge away. I still have belief in Whirlpool and I firmly believe my recommendations would not go wrong, and it is only the fault of the mechanic who could have made this remark unwittingly.