After months of careful research and comparison, I finally bought a pricey (over $2K) Whirlpool refrigerator with a bottom freezer and French doors with water dispenser on top. I really did not want any fancy features, just narrow doors because of my small kitchen, and a fridge on top because of my back pain. Since the date of purchase in May, 2014, I have had 4 service calls. The first was covered under warranty, but no cause of the sheet of ice collection and underside water leakage was identified; I did, however, receive a somewhat patronizing lecture on the importance of thorough reading and comprehension of the owners manual, and a statement that most of my service calls are for customer education. A follow-up service call, a few weeks later and also covered under warranty, identified the cause of the ice collection and water leakage: a faulty duck bill little piece of plastic in the drainage system that is a problem well known to Whirlpool. In mid-June of 2015, the ice maker had to be replaced, to the tune of $360.00. Today, I had a service call ($103.00) and received an estimate of $405.50 to replace the broken freezer drawer slides, which prevent the freezer drawer from fully closing. I will be applying that $405.50 to the purchase of the simplest model, non-Whirlpool refrigerator available, and have the Whirlpool hauled away. Besides the problems noted above, the center of the refrigerator freezes the food, while the freezer compartment arbitrarily defrosts. There are alarm icons that go from blue to red to alert you of the need to replace the (expensive) ice and water filter, refrigerator air filter and crisper freshener. Alarm bells ring to inform you that the doors have been open too long, but nothing alerts you to the fact that the freezer door is not completely shut, or that the freezer has gone into defrost mode because someone inadvertently brushed up against the control panel and changed the settings, or that water is pouring freely out from underneath the appliance. I have had to change my buying habits because fridge holds at least 15% less food, even though it is the same cubic footage as my previous (top freezer) one. Freezer contents easily slip down behind the top freezer drawer and jam the door open. I have to take most frozen boxed items out of their original containers and pack them flat in freezer bags to get enough storage. Some tall bottles do not fit anywhere in the refrigerator compartment, and have to get put in sideways. Even in the absence of mechanical problems, using this refrigerator is like packing and unpacking a suitcase many times a day. While Whirlpool customer service personnel were not overtly rude, there were dismissive and condescending overtones in some of the questions and directives I received from them, and another insinuation that service calls would not be covered under warranty if they end up being for the purpose of customer education. The extended wait (7+ days) for appointments with a Whirlpool-certified appliance repair company, along with the customer education exclusion, were absolute deterrents to the purchase of the extended warranty. Besides my personal disappointment and disgust with the purchase of this appliance, I am sad to see that the Whirlpool brand has slipped so far in product design, quality and customer support.

Purchased above refrigerator (WRF736SDAM13) over a year ago and it has been nothing but trouble. Ive had service companies out 6 different times. The doors never lined up or closed properly from day one. The final and last attempt to fix was putting caulk in the seal of the doors!! Left door does not seal properly and moisture builds up on inside. I requested several times for a new one and Whirlpool refused. Also purchased microwave, stove and dishwasher. Microwave went out 6 months after using it. They had to replace a major part. At least they did this at no charge. Just the hassle of having to be home 2 times to meet service tech. WILL NEVER purchase Whirlpool appliances again. Ive been using them for in all my homes in the past. STAY AWAY from this model.

I never knew an appliance could be manufactured as poorly as my brand-new, expensive, side-by-side whirlpool refrigerator. Within the first year, the icemaker line malfunction because of a fan problem, causing the line to freeze, break, and leak water everywhere. The ice maker stopped working. Everything on the top shelf In the refrigerator freezes. Everything on the bottom shelf stays warm. The motor is so loud and can be heard of rooms away. It is less than two years old now, and I am sincerely considering buying a new refrigerator altogether.

My induction cooktop totally failed to work two months after installation. Whirlpool sent a repairman who told us it was the main board. He also said he was unable to locate any of that part anywhere in his computer. We called Whirlpool via our store, Ikea. They apologized, asked for 48 hours to locate a part, then said they would replace the cooktop if they were unable to find out. Almost 48 hours later, they hadnt located it and denied any replacement option. The parts cost is over $800. The cooktop cost just over $900. Whirlpool reps would only read from a script of legal warranty jargon. Then they said they needed 5 to 7 days. We had a baby visiting - we needed our stove. To me, an apology would be replacing that unit if the part wasnt available, not a verbal statement. Fortunately, we had the phone # of a local Ikea manager who told us to bring the cooktop to the store as they had them in stock. They replaced it with a new one. Over the years of my long life, I have bought many Whirlpool products. Never again. I need a washer and dryer, and will not be purchasing any associated with the Whirlpool Corporation. Thanks to Ikea, though, for standing by their customers.

Spent the extra money to have a beautiful, slide-in oven. The AquaLift technology just seemed like another plus. After the turkey cooked, just seemed like another oven to clean. The AQUALIFT does not work, except for the bottom of the oven!! A fresh oven cleaner? Only available only. Get this beautiful range, not AQUALIFT TECHNOLOGY. CLEANING with it.

This refrigerator well paid for itself. I had over 25 years and it was still in good working condition. I had to leave it behind. I moved to a place where fridge was already. I hated to leave it behind. ‘twas offered to Goodwill but they never answered the phone for it. I surely hope someone got it.

GB2SHDXTS02 - Bought the Unit and an additional 4 yr protection plan. Shortly after the plan expired the plastic drip pan cracked and spilled water all over the laminate floor. It is still bucked from the water. Repairman came out and confirmed the crack, but we were without the refrig for a couple of weeks. Now the top doesnt cool, but the freezer does. Problem probably the defrost system, the fan, the control assy, or the thermistor, but I am too old to fix it myself. My fault for not checking ratings before I bought, but built in obsolescence is obvious here. Whirlpool used to be a good company, but I will never or will my family ever buy another appliance from them.

3 months after warranty the oven will not stay on. I will stay on for only 20 minutes then it goes out. It clicks but will not come on. I can only use my oven for backing biscuits but cannot bake chicken or meats.

New Whirlpool Refrigerator makes roaring noise like a broken engine. Whirlpools 2 technicians listened and confirmed but said that as the refrigerator works they can do NOTHING about it. Whirlpool management would not respond to repeated requests. Dont even get near ANY Whirlpool products!!!

I am very disappointed with my purchase of the Whirlpool Refrigerator Model # WRF535SMB. As soon as the warranty ran out, it began having problems with ice build up in the bottom of the freezer. I see this is a common complaint and wish I had read the reviews earlier. The appliance is only 3 1/2 years old. Other complaints - impossible to clean the freezer. Mold build up on the seals. Glass plate shattered in a thousand pieces when I very gently set it on the counter.French doors, white, freezer at the bottom.

This Cabrio Washer and Dryer are horrible!!! Dont ever buy one, they will not fix the F1 code, and Whirlpool customer service is non existent!! I hate this company, and will never buy a product made by them again! Be aware that Whirlpool makes products for Kenmore, Maytag, and a few others!!! I just want to spread the word about this washer! If you just bought one try and take it back for something else!!! STAY AWAY FROM WHIRLPOOL!!!

Bought the Duet front loader washer and dryer. Nothing but problems and repairs. When I decided to throw in the towel and buy new machines my repair man convinced me to buy Whirlpool again - Cabrio. Said they are amazing. Love them except the holes in my shirts. I bag my delicates but apparently I have to bag everything. So sorry I bought them. There was a day when you could count on Whirlpool. Replacing my crappy Whirlpool gold refrigerator right now too. Hoping LG will be better. Already replaced my Whirlpool dishwasher. Went to Maytag. This company has gone downhill. My mom had these appliances for 20 plus years - I spend thousands and cant get 5 years!!! Dont buy Whirlpool!

I purchased a Whirlpool Washer/Dryer set in June 2014. Yesterday, Sept 9, the motor stopped working. The machine was on but nothing happened. Called the repairman who said the motor burned out and had to be replaced at a cost of $180 plus $75 for his labor. I paid around $400 for it a little over a year ago and now I have to pay $255 to get it repaired which is ridiculous for a ONE YEAR OLD machine. I will never buy Whirlpool again. I should have read the reviews first before buying but I always thought this was a good brand. Lesson learned, never buy Whirlpool.

I like the double bottom french drawers but I don’t like that the top door hinge covers are plastic. Also I wish there was more height inside the refrigerator for tall bottles and pots. The wheels are great for moving.

I purchased my refrigerator four years ago from Lowes. From the second year ice would form in the bottom of the freezer weekly. This past week it stopped working totally. I had to call a repairman. He advised me the parts he had to replace were outdated and Whirlpool had made changes to the my refrigerator model two years ago. No recall. Just cheap parts that caused the refrigerator to not defrost. $400 later all is well and I am broke. I wrote to Whirlpool and their response was, Oh well, there was never a recall so youre SOL.

My Whirlpool oven (Model WFG505M0BS0) stopped working - the bottom oven part (the top burners were OK), the display on top functioned normally, but no fire came on. I called Whirlpool, and then I accessed Whirlpool online and scheduled service with their official service representative - Flamingo Appliance Service ** for September 9, 2020. When the repairman arrived on 09-09-2020, he opened up the stove and checked it, and he told me that a computer part needs to be replaced, as well as the igniter, and the cost would be between $400.00 and $600.00 (I dont remember the exact amount), I told SEVERAL times, maybe its just the igniter (for which the cost would less than $100.00 AND already included in the $134.95), but he insisted that the computer needed to be replaced, I did not like the way he explained it to me, it did not make sense.After that I was planning to buy a new stove, as the repair was too high. But, I decided to try to change the igniter myself before getting rid of the stove (the igniter cost was $21.00). I just got the igniter recently, and installed it, with help from YouTube, and what do you? THE STOVE IS WORKING!!! This is fraud!!! FLAMINGO APPLIANCE SERVICE ARE THIEVES, AND BY ASSOCIATION, WHIRLPOOL, WHOM THEY REPRESENT ARE THIEVES ALSO. I shall publicize to the best of my abilities: NOT TO BUY WHIRLPOOL PRODUCTS!!! This was not a mistake!!! This is the way they rip people off!! Either by paying exorbitant amounts for unnecessary repairs, or by buying new appliances when the old ones are still good. Dont buy Whirlpool!!! Dont use Flamingo Appliance Service. Theyre both fraudsters.

The self cleaning work very well. All you need is clean the filter every time you use the dryer. I had the large capacity. I can wash my blankets and heavy clothes like commercial machine and the machine is programmable for your wash load.

Whirlpool cabrio top load washing machine sounded like a jet engine taking off on spin cycle then started spewing grease on the floor. Called hotline with make mod ser #. Repairman came out 5 days later. OOPS! Whirlpool made a mistake, repairs not covered. Please pay repairman $450. Should have had him make the repairs then threw him out of my house.

We purchased Whirlpool Gold Accubake, double ovens (gas) in 2005. Since then, we have experienced identical failures (8 to date) during the self-cleaning cycle in which the high temperature burns out the thermal fuse of the ovens. This requires two Sears technicians to repair the unit (it requires two technicians to pull the oven out as the fuse location is in the back of the unit) and leaves us without use of both ovens for approximately 2 weeks (scheduling parts delivery and technicians through Sears home repair is not an expedient process).After checking other consumer product websites, it has become clear to me that there is a known design defect with these ovens in which the thermal fuse is not adequately insulated from the high temperatures during self clean; it therefore trips and burns out during the self-clean cycle. While not having access to ovens for about two weeks/year on average may sound acceptable to Sears, the reality is that the problem has escalated in frequency since purchase. In 2013, we are going on our third repair of the same problem (that makes 6 weeks of non-usable oven time in one year) and Sears will not consider replacing the unit, despite: 1) our obvious dissatisfaction with a lemon unit, 2) a well documented history of the defect with this particular Whirlpool oven and 3) an ongoing and escalating repair cost to Sears (it is under their extended warranty so the repair cost is on them although we did pay for this service up front on our appliances).I would stay away from not only Whirlpool appliances but also Sears as there doesnt seem to be any regard for the customer experience and taking care of a product problem (the right way) with a known defect. Sears has an opportunity to make this problem go away quite easily and retain a customer - fix the problem permanently or just replace the defective unit. Unfortunately, my experience to date with Sears standing behind the products they sell provides me with little confidence that either will happen.

I think the whirlpool washer is a very nice machine. I think it does a good job of cleaning but still has the tub odor problem that a lot of front load machines have. As far as reliability it has done pretty well but I did have to replace the tub bellow and it is only 5 years old. It also makes a lot of noise so it is not a quiet machine at all. The steam option on the washer is a nice feature but not sure how much it does to help clean stuff.

I have had my fridge (model WRX735SDHZ02) for 6 months now and it has never worked properly. All our food was getting frozen so we bought a thermometer to check the temperature inside the fridge and it was showing around 22F. The technician came 4 times and finally said that the fridge couldnt be fixed. He asked me to call Whirlpool since there was nothing else he could do. Every time I have called Whirlpool (6 times already) the wait times have been between 52 minutes to almost 1.5 hours. When I called customer service to tell them the technician said the fridge cant be fixed, Whirlpool said that I had to contact the technician again and schedule another visit. Whirlpool said the technician had to call them from MY home and tell them the fridge cant be fixed. I asked why couldnt the technician just call them now to let them know and why did I have to schedule another visit for that? Whirlpool said it was protocol. Makes absolutely no sense. In a nutshell, its been 6 months and my fridge is still not fixed and Whirlpool is not being helpful. If I could go back I would not buy Whirlpool.

I have a Whirlpool Cabrio washer and dryer combo. Recently, I have learned that the washer has a very common problem with the water pump. I have read amazing amount of complaints about this problem and apparently the company has nothing to say about this. The cost for parts and labor for replacing this pump is about $400.00, almost half the cost of the unit. This is unreal!

I paid about $400 for this dishwasher and the regular price was over $600. Got a good deal. It washed dishes wonderfully. All I had to do was scrape the chunks off. It cleaned the rest. BUT... at a certain point, it started NOT cleaning. It was only about 6-7 months old. It was to the point where everything just came out kind of slimy and food grit was re-deposited on the dishes. I cleaned both filters. I made sure there was enough Rinse-Aid all the time. I ran hot water in the sink before starting to make sure the temp was hot enough. My husband went online and someone had instructions about cleaning the water intake because it could sometimes have sediment buildup. Not a difficult process, but there was no gunk in the intake filter. When I listened to a load it seemed like it drained, (most start with that), paused, rinsed for a couple minutes, paused, drained, paused and refilled for the wash cycle. So the pump worked, the arms went round and sprayed. Nothing was in the way of the arms. After it started the wash cycle, it seemed to just stall. It would spray for about a minute and then stop. Im not sure it sprayed after that. The timer kept counting down. It said dishes were clean, but it was an absolute waste of time. I was ready to go buy a cheap dishwasher and throw this one in the dumpster. I think it is a 720 padm??Just after my husband checked the water intake filter, we started another cycle. When it was rinsing, he opened it up and everything seemed to be working ok. It drained, then filled and started the washing cycle and then stopped. He opened it back up and surprise, the water was full on the front level by the float (that turns the water filling off). But in the back of the dishwasher, there was only about an 8th of an inch of water. Online it said the water should fill to just about the top of the heating element. It WASNT. Problem? It wasnt LEVEL. The instructions when installing said it should be leveled. We did when installing it (when it worked great). But looking back, we put in a new hardwood floor about the time it stopped working ok and we didnt put 2 and 2 together. We did not re-level. When we pushed the dishwasher back into its built in cabinet, it must have gotten OUT of level.The rinse part worked I guess. Then it drained and re-filled. After re-leveling the dishwasher, we opened the door at that point. The water was a level depth front to back and side to side. My husband explained what he thought had been the problem to me. When the wash cycle starts it fills, the float shuts off the water at the appropriate level. THEN... the dishwasher starts to pump and fill the arms and the tube up the back that feeds the upper washing arm. So much water goes into the arms and up that tube, the dishwasher looked almost empty of water again. As the dishwasher was now level, it began adding water to compensate for the arm/tube filling. Before the float would shut off too soon because the front part of the tub was full but the back wasnt. Without enough water, the dishes were NEVER going to/COULDNT get clean.The re-leveling made sure that the float didnt turn off the water filling until there was much more water, the CORRECT amount. The next load cycled all the way through, spraying much more than Id heard before and the dishes were clean. P.S. I also got some dishwasher cleaner and used that on a couple empty cycles. I NOW LOVE this dishwasher again. FYI If my husband wasnt handy Id have junked this thing. We HAD leveled the dishwasher when we installed it. Just didnt realize it COULD get un-level just pulling it in and out of the cabinet to install new floors. Check out all the troubleshooting stuff in the manual. But if it doesnt help, put a level inside across the bottom rack, front to back and side to side and make sure the bubble is in the middle of the two lines.The previous dishwasher I had, just made like a fountain of water that went up the middle of the dishwasher into a sort of funnel filling the upper arm. THIS one has that tube up the back and it curls down under the filter and Im guessing it is more sensitive to being OFF LEVEL, because the tube doesnt go straight down, it curls and lays across the bottom of the tub. Without being level, there was never enough water to suck up that tube to start the the actual wash cycle and it just stalled there till the timer said clean at the end. IE: dishes never did wash. BUT IT DOES NOW! Woohooooo!

I bought the stackable Whirlpool Duet. Piece of garbage (model # WFW9150WW). From day one the washer never worked. Error lights/bells kept going on before the second spin cycle. First repair guy couldnt figure it out. And the manual says just unplug and plug the power cable back in. Sure--every time I use it? I called Whirlpool service and they said a new control board was needed without even seeing the machine, which tells me this is a manufacturing flaw. I waited 2 months for the board. When it came, the repair guy put it in and then the machine would not stop filling. So another switch and hose are being ordered. Whirlpool customer service is completely useless. And no one will even discuss replacement. Now Im stuck. $700 out on the first machine and $200 on the extended warranty, which will be useless because Im going to dump the machine. And additional $800 on another new machine which probably wont work either. Oh, yeah, and you have to use special soap, which Ive tried, and got down to using only 1/2 a teaspoon because the suds never cleared. Please tell all your customers never to buy Whirlpool!

Do not ever buy a Whirlpool refrigerator. Sloppy construction, bins dont close, doors dont seal well and a brand new fridge doesnt cool to a safe food zone. When we call for service, I got the run around for almost 2 hours. They wont be sending anyone to service a brand new unit for an entire week... And thats 2 days before Thanksgiving! I have never had an appliance made this poorly. We dont have the space for a bigger unit, so thats why we bought this model. Size shouldnt impact quality!

I bought all my kitchen appliances in Home Depot 4 months ago (April 2014). The wall oven, Whirlpool, never worked. Flamingo Appliances is the name of the company that does services for Whirlpool in my city. They keep changing parts and today is the 3rd visit that the technician will be in my house trying to solve the problem. Customer service in Michigan is DISGUSTING! I probably have to buy another oven because they say they wont replace it if they think its fixable. 3 MONTHS! I will never buy Whirlpool again. I hate them.

Bought this washer 3 months ago. Absolutely hate it! Leaves white film on my clothes. Have to run all washes through a quick wash to get the film off. Hammers the water through the pipes, causing the fittings to come lose and leak! The spin cycle practically dries the clothes leaving them so wrinkled that I have to dry them longer to get the wrinkles out. Waste of my time and MONEY!

Front load is terrible. Doesnt wring clothes thoroughly. Runs for 1 hour on fastest cycle. A HUGE WASTE OF ENERGY! NOT A GOOD MACHINE!!! Our clothes are wet always after the spin cycle. It also doesnt do small throw rugs. Awful!

Purchased Whirlpool Cabrio model WTW6400SW washer and dryer 1/7/2007. The matching dryer was dead on arrival and the second dryer motor died within a year. Washer: 1year 2 month the washer motor died. Whirlpool paid for the part and I paid the labor. The following year, the bearing went out and the outer tub was replaced (the bearing is inside the plastic outer tub - bad design. Whirlpool paid for the part and I paid the labor. Feb. 2011 had one of the F errors. Whirlpool repair tech came out as the tub would not drain and it was a wire that had come loose underneath washer - another service call charge. Dec. 20, 2011, I had an error F50. The Whirlpool repair tech came out, verified no clothes or money stuck in the machine. All clear. He called higher level whirlpool tech and they paid parts and labor to replace the main control board and the RPS Sensor. Im single and am not abusing this machine. Like everyone else who posted. I paid close to $1,000 for this washer (not including the dryer) and I have been a faithful Whirlpool customer for 3 generations, but if Whirlpool doesnt offer some kind of compensation/trade in credit to customers who purchased this (knowing that the design is bad/faulty) washer and discontinue this model. This will be my last Whirlpool. I will have lost all faith in Whirlpool. The Whirlpool service tech that I found is op notch. I will miss him if I have to switch brands. Im putting 1 star as I know this machine will not be operational for 9 years which is the minimum that I would expect. If it makes it to 6 years without another service call, it will be a miracle.

It was on sale and the price was good for comparable refrigerators. The biggest problem is that instead of a simple dial to control temperature, you have to be a computer genius to figure out how to turn it to a different temp. even by the instructions. And the ice maker throws ice all over the floor even if you hold the glass up against the top. When I first got it, it made a very loud noise when it run, but that changed with time to a bearable volume. Everything seems to work well other than those few little things.

After only 3 years using my Whirlpool front loading washing machine the inner tub is already broken. The repairman said the cost is just about the same as getting a new washer. After reading all the horrible reviews on the Whirlpool washer I WILL NOT be getting a Whirlpool. I am so disappointed in the washer and do not recommend it to anybody. Do not buy a Whirlpool appliance ever.

This is a horrible washer. It leaves a white residue on dark clothing and the clothes need to be rehashed. There is water that settles in to the fabric softener dispenser. Now the washer is leaking. My husband replaced the tub seal or whatever since he found this could be the problem while searching the internet. It is still leaking and we have no idea from where the water is coming. I agree with the other person that the Whirlpool customer service cares not that theyve manufactured a defective product.

Terrible wash machine. Some clothes come out having never even gotten wet. The spin cycle ties your clothes in knots so bad you have to machine dry them because the wrinkles are ridiculous. I’m all for saving water but if your clothes don’t get wet, how are they going to get clean? Also can’t do just a rinse and spin cycle. I would rate zero stars if I could. Don’t waste your money on this junk! Wish I could buy an old fashioned Maytag. Those washers were the best!

We purchased a Whirlpool conquest from Lowes in 2009 and purchased a Lowes warranty. About 2 years ago we started seeing hairline cracks on most of the drawers and shelves. I complained about it last year and a lady from the Facebook page did offer 50% off new ones. Since then we have not been able to afford to get any, and today we lost our last shelf. If I wouldnt have checked it, it would have broke along with anything on the shelf. I have never seen such horrible parts. We have another small very old fridge that has help up better than this. At this point I will never buy another Whirlpool.

We purchased a Whirlpool Cabrio Washer and there is a bearing problem (which seems to be the common issue reported). The washer is unusable at less than 5 years of age.

Electric hot water heater model E40H6-45-100 - Purchased at Lowes. Husband installed, tank filled, no hot water coming through house lines. Called support center several times after trying each recommendation that did not work. They kept saying it was a plumbing problem. My husband is very smart when it comes to electrical and plumbing. He has done numerous repairs to our homes over the last 30 years we have been married. He knows what he is talking about and told the support tech that he believed it was a faulty water heater. She immediately said the units are all tested before they leave the factory. The final step was to remove the nipple that the hot water flows through out of the tank and remove the two black bellows. Now my husband can see directly through the piece but also decides to put his finger through the the open whole on the top of the tank and cannot get his finger through - it is blocked. He gets a flashlight and a screw driver. Puts the screw driver through a thin plate that was blocking where the water should be coming through. He can now actually see the water in the tank. This was the whole problem! So they could not have tested this tank. They did give us a ref number to take parts back to store to replace parts we already bought and cannot use. Its the time and energy on whats suppose to be an easy job that counts. Will not recommend Whirlpool products to anyone and probably will not purchase any in the future. Ours was not as bad as most of the other reviews I read but wanted to advise others who may think about what brand to purchase.

In November 2016 I took delivery of a Whirlpool WRF757SDEE French door unit. One month later: In December 2016, it needed a new ice maker, as it never did fill the ice bucket and they were always melted together. Two months later: In February 2017, a thermal fuse had to be replaced—refrigerator compartment wasn’t cold enough. 8 months later, Aug 2017, it needed electronic circuit board replaced, as refrigerator compartment completely froze up. November 18, 2017 manufacturers one year warranty expired. BUT, I HAD PURCHASED AN EXTENDED WARRANTY! 4 years from NSI Protection Plus (a joke, see my review.)December 31, 2017: One year and one month after delivery, the unit stopped cooling completely. My local appliance store where I purchased sent out a tech and took it into the shop for diagnosis. They found the sealed system was kaput. Couldn’t get the temp below 67 degrees. My dealer was great and sent out a loaner after a week, and for almost 7 weeks they argued for a replacement with NSI Protection Plus. Finally on February 8, 2018, they threatened to take them to court and they paid $15 less than my purchase price. I’m out $189 for the “warranty,” $188.48 sales tax and $89.95 delivery. And I have to go buy another refrigerator. It won’t be a Whirlpool.

Steam cleaning DOES NOT work! I have complained to Home Depot and Whirlpool since my purchase 9/2018. They sent 2 different repair men and both times I was told there was nothing they can do. I got one phone call from Whirlpool (Maytag) and they sent me a cleaner (wish is just for the stovetop). No other return emails or calls have been acknowledged. My stove looks like it hasnt been cleaned EVER! I was also told to use elbow grease. I am so disgusted and at my wits end. Any suggestions, besides court?

I like the dishwasher. It cleans pretty well. Some time it soap doesnt open and the dishes don’t get cleaned. But when it’s working good the dishes get cleaned very well.

I purchased an extended warranty with my product purchase and only a year and a half into using this brand washer the lid broke on one side at the hinge, it looked really rusty and like others I thought I was making a very decent purchase because all of my previous appliances were Whirlpool so figured Id keep up with the brand. Sad to say that was the worst decision I could have ever made for 13/1400 dollars for a washer with a light inside. Never again. They wouldnt even keep up the warranty because they said it was too expensive to repair it. Whirlpool is very bad for business...

My agitator-free washer began tearing small holes in my clothing and sheets about one year after purchase. I contacted Whirlpool and they sent out a service person, who ran a diagnostic test on the washer and said it was fine and I should learn how to wash clothes and load the washer, etc. The barrel of this washer has little holes and I believe that when it spins the clothing, some pieces may stick in one of those holes causing tearing. The service person also told me that my clothes were old. I guess that means this washer is not for washing old clothing. The tears in my clothing are in places that are very unlikely to tear, like the back of my jeans behind the calf of a leg, about half way up from the ankle. There are holes in my tee shirts at the bottom of the back. Even if I were a smoker, which I am not, I would not likely burn holes in those areas. Whirlpool obviously does not want to accept responsibility for this problem, even though there are many other people having the same problem with this type of washer.

Bought water heater from Lowes in 2016. 4 days ago I came home to find water all over garage and a burnt smell coming from the water heater. Whirlpools warranty department is absolutely horrible. I spent 3 days sending pictures of the water heater, circuit breakers and water on garage floor with cc sent to my husbands email account and mine. Each day I would telephone the warranty department and told that they never received pictures and they couldnt do anything until they received the pictures. I asked for a supervisor who wouldnt even come to the phone. Both my husband and myself received the pics and email just fine. A representative said they have firewalls and things attached so that they cant receive attachments and downloads. So I sent directly from my phone and they still claimed they never received. They refused to give me contact phone numbers for supervisors. Out of frustration I called the Lowes store where I purchased and a store representative spent 4 hours making phone calls trying to help. She was completely frustrated as well. I was told even though there is a 6 year warranty, I am to pay parts and labor and that the repair company for my area that Whirlpool utilizes doesnt even deal with Whirlpool parts so that whatever is needed would have to be ordered! Im on day 4 of no hot water, this is absolutely ridiculous. I will NEVER buy another Whirlpool product! This product was installed by Lowes and inspected by the state, not a DIY!

We purchased a Whirlpool refrigerator because of the brand in August of 2011. Its December 2012, the entire door needs to be replaced. It appears the cost will be as much as the original $750 investment! We called Whirlpool expecting they would stand behind their brand after hardly 18 months, but no ... It is clearly a defective door to begin with.

The oven is a joke. It does not self-clean. I have to buy oven cleaner and clean the oven like in the distant past. They are lying about it being self-cleaning. Do yourself a favor and buy a real self-cleaning oven. NEVER WHIRLPOOL.

Cabrio top load HE washer - Ive only had the washer a couple of years. My husband bought it for me thinking it would make washing more time efficient and energy saving. Lesson learned! After struggling with this washer for the past year, I was told today that to repair it, it would cost around $800 or I would need to buy another washer. The washers bearings and tub need to be replaced and it will not spin properly or at all. Previously, I have owned washers for over 10 years each. This was definitely not a good purchase. After reading all of the other complaints on this site, I understand that I am not alone. It was also mentioned on one complaint of the possibility of a fire hazard with this washer. Whirlpool should be recalling.

Cabrio Whirlpool washer - I hate this washer. Had it for about 3 years now and it will not spin out and does not give a code. Called a service tech out and they cannot find anything wrong with it. The water goes out but will not spin. It sits on 20 minutes and does nothing. Will not buy another Whirlpool washer. Wanted a good washer and got a piece of junk. Will not recommend it to anyone else. Think Im going back to the old style.

I purchased a 40-gal Whirlpool water heater model 40t91-403 last week and paid a plumber to have it installed. The old one (GE 40 gal) worked fine except for a leak. The new one used all of the old connections except the 2-inch in and out pipes. Same connections, hot, cold and gas. At first I got about a quart of hot water and then all cold. Whirlpool changed the valve and cold water pipe (inside the tank) and still the same. They are trying to tell me that the tank is fine - I have a plumbing problem. Two plumbers have told me different, but still they insist. Yes, I am upset. The old GE, even with a leak, performed better!

I bought a Whirlpool Cabrio washer on 11/07/10. I brought it home, hooked it up, turned it on and water came pouring out the bottom. I should have known better then, but I took it back and got another one, same model. I dont even have it 2 years and its locked up. I had a repairman here and was told it needed a new water pump ($200 plus). There are 3 adults in my home so its not like I use it hard. I am really disgusted. This is the 3rd washer I bought from Whirlpool in less than 10 years. I went on the Whirlpool site and voiced my disappointment and my problems with their washers. I was told they take pride in their products and I should have a nice day. Yeah, right, they dont have to drag clothes up and down the stairs and then to a laundromat when theyre in their 50s with a bad knee and back. Yes, I will have a nice day when I get that piece of junk out of my house. I will never buy anything made by Whirlpool again.

I purchased this monster in 2012 and after six years of enduring not enough water to actually wash the clothes for years, now the bearings have gone out making it sound like a jet engine is in my family room when it spins. After researching the bearing issue, I find it will cost $250 to $300 to have them replaced. Its also a common problem in this model even when the washer isnt at all worn out and old. That combined with the fact that my clothes dont smell clean and some blankets come out not even wet at all, Im done. I wont ever buy a water efficient washer again. Churning the dirty underwear around with a few cups of water isnt acceptable. NOTE: The bearings left months after the extended warranty expired. Just like clockwork. I purchased a much cheaper - center agitator - washer with a deep water option available. It was half the price of this top of the line Whirlpool Cabrio Washer.

I bought Whirlpool top-loading high-efficiency low-water washer Sept 2018, model WTW5000DW, Serial # C83444466. Worst washing machine ever! No matter which water level you choose, it will not dispense enough water to cover the top of the clothes load, therefore the clothes are just moved from side to side with only the bottom layer of clothes getting wet; top clothes stay dry. Not enough water to fully agitate to clean the clothes!Whirlpool serviceman came today (Jan 13, 2020) to recalibrate the settings. VERY NICE MAN BUT THERE WAS NOTHING HE COULD DO TO SOLVE THE LOW WATER LEVEL. Recalibrating settings did nothing to solve the problem of not enough water. I am 81 years old and I have to manually add at least 4 buckets of water to an average load of clothes. This is unacceptable. Wont someone please initiate a class action lawsuit against Whirlpool for selling this very obvious poorly designed machine? NEVER EVER BUY A WHIRLPOOL WASHING MACHINE. It is a waste of money.

I moved into an apartment in July 2010 after closing in May 2010. My microwave by Whirlpool stopped heating a few days after the one year warranty was over. This appliance was of April 2009 series. My builder doesnt take responsibility and Whirlpool asks for huge service visits and repair costs that leaves me with no choice but to replace, and that too with the same product. This will cost me about $600-700 including installation and warranty, etc. I strongly believe that consumers should be protected against such liabilities. I have to pay for the product, the removal of the faulty one, installation of the new one plus taxes, plus transportation etc., only because Whirlpool sold it and the builder bought it (they are also hand in hand with these suppliers and dont bother after occupancy). God save us from such eventualities and undesirable expenses which hurt. No one should buy such items.

Whirlpool Dishwasher Model WDT7820PADMO was installed last October. Small parts began detaching themselves from the first day. Then machine leaked onto floor two weeks ago and I shut it down. As it was purchased from Sears, they and Whirlpool have batted responsibility for repairs back and forth until proof of extended warranty was supplied to Whirlpool. They then scheduled a repair job for a week later with an unqualified technician, who naturally refused the job. Upon callback, I was rescheduled for a day two weeks hence. As it turned out, the repairman would not be near my home on the appointment date. Luckily, I tried to move the appointment up, as the repair service said Whirlpool did not supply proof of the extended warranty. I saved five days waiting time by rescheduling, but have to supply proof of extended warranty yet again. All this for a dishwasher that takes three hours per load, and doesnt do a particularly good job of cleaning.

Just bought the Whirlpool 3.5 cu ft, Top Load HE washer (model WTW4815EW), but of course, the sales person did not explain that HE meant LOW WATER USAGE. Wish I had done my homework. FIRST LOAD, clothes seem to be beaten to death, and must pour in detergent before you load clothes. So, Oxyclean detergent I always used in my regular (NOT HE) washer put a hole in one towel and discolored (faded out) the others. Also seems that the fast and hard agitator would not (logically) last very long. It seems to be working very hard. Im SO disappointed. Called Whirlpool to say I dont like it. They said to call Home Depot and see what they will do about an exchange. When I did, my sales person said that almost all the washers he sells are HE. I want the old type washer back that allows me to add more water if I want, change the cycle and water levels at my discretion, add detergent when I want to, and soak clothes if I wish.

I just bought a house with a Whirlpool Accubake wall oven and after I did a self-clean, the oven quit working. It goes through the motions of working but neither element heats up. After replacing the elements ($95), I am going to replace the thermal fuse to see if that cures the problem. Whirlpools automated Customer Service phone service sucks. You cant talk to anyone about troubleshooting any problems so you spend money until you eliminate all possibilities.

The 12 year warranty, means nothing. The heater only worked for 30 months, and then its upper sensor fault code flashes, and the heater shut down. I called Whirlpool, and they have me use an ohm meter to help troubleshoot the problem. So if you are not handy, you are out of luck. They decided it was my control unit that is defective. They will send me the part free, but I have to pay shipping and installation. What a deal, and what kind of management would dream up of this. The heater is marketed as a 12 year warranty model (only on the tank). Would anyone, having been through this, buy another Whirlpool product?

Installers left and Home Depot Cabrio washer stopped with water left in tub. I reset GFIC outlet, tried again and it stopped. Did some research and tried different outlets. Same result. I discovered that if you shut off machine as soon as the GFIC is reset, then the washer will drain no matter what. I have been on the phone with Home Depot and they have no solution but to wait one week for a repairman. Very dissatisfying service. Now I am running a 20 foot, 3 prong, heavy duty extension cord into living area where there are no GFIC outlets and it has been running. I believe there is a fault in the washer, but they must not care if we get electrocuted from the faulty grounding of their Whirlpool product.

It works quite well except if you put items in the back of the top shelf of the refrigerator it will freeze them as if they were in the freezer section. I have a bottom freezer and that works quite well. And it is very quiet when running.

Yesterday I purchased this Whirlpool top load washer model WTW4816FW with agitator and we installed it at our vacation home and I started a small load to wash. Yikes, it made noises like a machine that is on its last legs. I knew from washing clothes for 40 years that this is NOT right. We, hubby and I waited and listened to this piece of junk to finish the cycle. Thank god I had set it for a short wash. We also videoed this contraption while it was grinding. I called Lowes and politely told them I was returning it. Thankfully they never had a problem with us bringing it back. (This must happen often.) I go back to the appliance department and decide on a Maytag. I noticed that it looked like the junk we just returned. I stood there and looked up the model number online and lo and behold there was a video of it doing exactly the same noise. It was virtually the same machine I just returned with just a name change. Needless to say we left the store washerless until I can research this further. I then found out that Whirlpool now owns Maytag. Thing is I just bought a front loader Maytag for my main home and it works good. It was a replacement for a Whirlpool without a agitator which worked well too. The YouTube videos seem to be washers with agitators doing this. I just wish I could post the video for all to hear. I guess we are all at the mercy of big companies who dont care if they make a good product as long as they can make it cheap.

I bought an adapter that I added to the kitchen pipe, drilled a few holes in my cabinets to route the hose and voila! It is small but big enough so it's perfect for me. I didn't realize it had an internal heater so I was moving the hose between hot & cold under the sink but now that I know. I will try the heater. The settings are complicated so you have to read the instructions fully. Before I read them I thought every load took 2-3 hours but they don't. I do like to use the heavy soil setting and that does take a couple hours, but if I'm in a hurry or the load is not that bad I use a shorter 50 min setting. For the drain hose I either put it out the window or put a screen in the sink & tie it to the faucet. You have to tie it down wherever you aim it because the water comes out with enough force to throw the hose. I had a couple incidents of kitchen flood before this stuck in my head, now that sucker is secured well. I intend to make a permanent drain to the pipe eventually but for now I just use window/ sink. This required a longer drain hose. For apartment use, I am very happy.

Bought this model from Bad Boy in 2006 and just after the warranty ended the problems began. We kept getting the F1 error code so with a little internet research we found it was a known problem with Whirlpool. I contacted them and was told they knew nothing about this issue being nationwide, however I emailed them copies of the complaints and responses. They sent out a technician who had to replace the motherboard free of charge. Next issue was a loud noise coming from washer sounding like a jet plane taking off. Hubby ripped machine apart to find the bearings blown apart and in tiny pieces. We ordered new ones and also found that when the new ones arrived they came with a tube of grease and a sealer to use so water would not get in later and cause more problems. Funny there was no sealer on the original bearings.Next the lid lock finally failed, ordered a new one but did NOT install it back into the machine, now it sits beside the machine. In case it fails again we will have total access to the laundry this time. Finally the UL error code keeps coming up. I refuse to put any more money into this machine again so I am allowing hubby to fix it if he chooses, whichever way he wants as long as no money is involved. So right now we have bungee cords holding the suspension rods tight to help with the uneven load code coming up all the time. Personal thoughts - DO NOT BUY WHIRLPOOL washer/dryers. They are crap and the company just does not care and they try to lie their way out of repairs if people have not done their homework.

I had a Whirlpool washer for three years that I bought at Sears and it started making a noise. I called Sears repair and they said it was the bearings. Would cost 600.00 dollars. The machine is still running making a noise are there more in a machine. I will never buy a Whirlpool product. I just lost my husband and I cannot find the bill but I am calling Sears tomorrow.

Agreeing with many. How disturbing to buy a Cabrio Whirlpool washing machine about 5 years ago. I might as well go down to the river and wash my clothes. The bearings went out which means I have to be the spin cycle. I am hanging out my clothes on the line - very wet - until my husband buys the part and fixes it himself. I had my maytag for 25 years. An awesome, dependable machine that we laid to rest because of rust. We should have gotten another drum instead of buying this machine. Where are the engineers that are making dependable appliances to last a LONG time? We have not gotten smarter. Or we only care about the all mighty dollar. Make something to last a short time so that you have to buy again. We will do some extensive research the next time we buy a washing machine. Do not buy this machine!

I have had this Whirpool Cabrio washer now for one year. Clothes always come out wrinkled (even after drying). It leaves clothes unclean and leaves white streaks in clothes. Water level is so low in, that it cannot rinse or wash clothes properly. After washing towels, when removed to put in the dryer, soap is left in towels. I have had a repairman here, he says the design is bad, yet reports works as designed. Dont buy this washer. This is a piece of junk!

Electrolux dishwasher model EI24ID50QS - My husband picked this dishwasher after reading all the good reviews. However, after having issues with it, I tried to post my review and it would not post. I think Electrolux is somehow only posting good reviews and leaving out the bad. I had a technician come out to see why it took 6 hours to go through the cycle along with not cleaning the dishes well. He said I needed to run hot water before starting the cycle and that I needed to prewash my dishes before loading.In other words, its not a dishwasher but a sanitizer. Keep in mind that I rinse my dishes before loading, so I dont have food particles stuck dry on my dishes. So, I used his method of running hot water before cycle is started. It works ok when you dont use your kitchen faucet during the dishwashing cycle. However, the minute you use your faucet, the dishwasher runs for 6 hours! This is the worst dishwasher ever! Not to mention, the control panel is so sensitive that if you accidentally touch a cycle to start, you cant get it to cancel. It is ridiculous. Dont buy! It will be your biggest mistake.

So I have had the washer for a few years - bought it new or at least I thought. First came a clunking noise - fixed that. Next came the F1 code and installed a new pump $90 plus dollars. After installation, Im still getting F1 code and am now being told it is the ERC control board or water inlet valve either way a guessing game which in the end will have cost me over $400 to fix myself. I wish companies like this would stand behind their merchandise.

Bought this washer two years ago. First experience was when a load of towels became wrapped around the agitator. Called in service tech who told me to load the bin with the cloths pressed against the bin wall away from agitator, as if the cloths/towels would stay away from agitator. Two years later, Im ready to the machine to the street. Forget sheets and bedding. The agitator wraps them so tight that I almost rip the cloths/sheets to unravel. I had to wash a pair of work pants that were soiled with mud three times and there was still a stain. I will NEVER EVER buy another Whirlpool product.

Bought a commercial coin operated Whirlpool washer on 4-18-2015. As of this date machine has not been used that much, the electronic part has gone haywire.All lights on and shows the door lock (which is not) disconnected, nothing changes when I put it back. Contacted Whirlpool technician, have been told that this is a defective model. He has apparently had several service calls that are new machines and they are all the same issue. Told to contacted Whirlpool, Whirlpool playing dumb. I have several other older Whirlpool commercial washers and dryers, never had issues. I guess they are doing shortcut garbage machines. Also, the interior of machine is less sturdy than the older models. Will not buy any Whirlpool products again. They do not stand by their products try to tell me that they are not aware of defective machines. Cheaper to play stupid!!! Disappointed with their lack of standing by what they sell!!!

We purchased Whirlpool Cabrio Washer WTW5600 series in October of 2010. I bought the machine from Sears and also bought the extended warranty. Less than 6 months after I had been using it, I noticed that all my husband’s shirts were getting sweat stains under the arms and my hand towels were very smelly after drying with them one time. I called Sears to have someone come out and tell us what the problem was. He said I was using too much detergent so I reduced the amount of what I was using. It did not help the problem so I started using the extra rinse each time I washed, still did not fix the problem. I called them out 3 more times in 2011. One tech told me I was still using too much detergent so I reduced down to 1 tablespoon like he suggested. I stopped using softener in my washer because he said I needed to clean my machine more than one time a month, to clean it every 3 weeks. No solution to the problem still. I have had a tech from Sears and one from Whirlpool (who incidentally was the same man, he was from A&E Appliances). When he came in the door, my husband told him he had been here before and I said 2 times. He lied and said he had not been out before. Are we blind? No. He ran the cycle but sat in his truck while he was running it. None of the techs have ever put a tool on the machine to check if the water level is right. They just stand there and tell us to change the amount of detergent or clean the machine with Clorox more often. I cleaned it 8 days in a row and the clothes still smell and still do not get cleaned. We talked to main man at Whirlpool and said they couldnt do anything because their 1 year warranty had run out. We have been using Whirlpool appliances for over 30 years but I will not ever buy another one. I have probably had 5 Whirlpool washers over the years but never had a problem until we got this Cabrio top loader without an agitator. I would not recommend this washer to my worst enemy, if I had one.

We just purchased a new fridge - September 2021 -- Whirlpool side by side. Why is just okay? It is a loud refrigerator. A roaring sound is pretty constant. The ice tray in the door has no recessed tray ... so water and melting ice just follow down the front of the door and onto the floor. Two days after purchase we went back to Lowes to return this fridge ... but all the other refrigerators do not have a recessed ice tray. And since they are not plugged in ... who knows if they roar.

We purchased our home in 5/09. Within a month, we had to replace the defective gas valve due to inefficient burning. Our house smelled like gas each time we used the oven. It was under warranty at that time so Whirlpool replaced it. It is now 5/12 and out of warranty. We called a local independent technician who informed us the oven wouldnt turn on due to another issue with the gas valve, the same one that had been replaced shortly after we moved in. He went to his local supplier to purchase the gas valve to be informed that they couldnt seem to keep this particular gas valve in stock, simply because its a reoccurring known issue and Whirlpool needed to do something about it. So, this technician encouraged me to call Whirlpool. I called the 1-800 number, spoke to 3 different people and was constantly informed that since it was out of warranty they would do absolutely nothing! Again, I was informed that this gas valve is a reoccurring known problem with Whirlpool so perhaps they should consider looking into this issue. The last person I spoke to was a bit snide and just kept saying It is past your warranty, we will do absolutely nothing to help you, and sorry you are having that problem. We are not aware of this reoccurring gas valve issue. Have a good day!” Whirlpool, do you understand your reputation is at risk when you dont want to stand behind your parts that should work after 3 years! Should a brand new part not work properly after a month? Should another service call have to be made after 3 years? Sounds like a quality issue, something Whirlpool needs to investigate especially after a local supplier states they sell this particular gas valve all the time due to a reoccurring issue.

I had purchase a Fusion Supreme refrigerator (model 180). After some time, I found that the color of the refrigerator was faded and I very well know the color of the refrigerator was recolored. This is a concern on your prestigious brand’s image.

I bought three Whirlpool appliances (fridge, gas dryer and washing machine) from Abt in June 2012, delivered in July 2012. The fridge has not cooled from the moment we plugged it in and because I am out of state from Abt (IL), I have to deal directly with Whirlpool. According to both the Whirlpool customer service rep and her supervisor, if a product is defective from the start, Whirlpools policy is to try and repair it until they determine it to be scrap and only then will they replace/refund. I find this policy appalling since I paid for a good working product, from a company Consumer Reports rates very highly, but was shipped a defective one. Now, I have had two service visits, the second because according to Whirlpool the first technician did not perform the correct service. I have been told not to put anything valuable into my freezer for 5-7 days because most likely I have a coolant leak and the fridge is bad. This is terrible customer service and instead of fixing their error which is the purpose of having customer service, they are quickly building a reputation for a terrible product and terrible service. Good customer service would be replacing the defective fridge as it is clearly their manufacturing issue, taking the item back to their warehouse, repairing it if possible and selling it as reconditioned for a discount. I am noting my suggestion in case any Whirlpool representatives read this website. Another interesting item to note is the gas dryers absorb air from the environment around them so if you do any painting (full room or touch ups), the clothes that come out of the dryer may have a burnt/gas smell for up to 7 days. I am still waiting to hear back from the Whirlpool technician as to my burnt smell problem/resolution, but was told this from a separate service representative so I thought I would pass it on.

Whirlpool Gold model WRS526SIAHOO - We purchased this refrigerator 10/2013 with all the matching appliances when we remodeled the kitchen. We moved our 1997 GE refrigerator into the garage. Now the computer board has gone out in the Whirlpool and we are back to using the 97 GE. The technician told me that he sees a lot of these boards going bad.

I bought this Whirlpool french door, bottom freezer refrigerator for $2100. In 10 years I have replaced the compressor three (3) times. Bad design and a real piece of crap! I was told by Sears that all Bottom freezer Whirlpool refrigerators are made by Amana. That is why I bought the frig. Ive had wonderful experiences with Whirlpool and Amana product in the past, but this time their design is so flawed.

Apparently my machine, bought in 2011, was the first year they were made in the US. The washer has leaked soap down the front (a front loader) since day one. Service has come and replaced just about everything and its never helped. Its literally a piece of junk. Very disappointing. My older ones were great.

Whirlpool Cabrio Washer - This is a horrible washer. I just read the reviews after having struggled with dirty clothes, smelly clothes, sour clothes and yes, our water bill is way higher using this nasty machine. I will never buy a Whirlpool again. Very VERY disappointed and dissatisfied with this machine. I usually always read reviews before buying anything but the sales guy at Garner Appliance said this was an awesome machine. We bought the matching set. And to read each and every consistently bad review with the same issues. They should replace these pieces of junk for us free. The dryer doesnt fall too far behind.

I purchased a Top load Whirlpool washing machine, replacing my old Whirlpool. I am so unhappy with this new one. I noticed that the water level are low...I had the tech here twice and they said that if here isnt any lights on the dash that the machine is working. I called the head tech, same answer. When I put the clothes in the washer I make sure that the clothes are evenly placed in the tub. The clothes comes out tangled and some not clean. Tonight I noticed that a pair of pant at the bottom of the load had white smudges/ I am so unhappy with this piece of junk/ I cant afford to buy another washer, so I am stuck with this.. I have tried all the different controls, still bad. I know the new machine are different than the old ones. I still believe that the water levels controls are not working. I have used my sister new washers and the clothes are not tangled and they are all clean.

I bought a Whirlpool Cabrio 1.5 years ago and it has already died. Repairman need to replace the control board which had gone out. $450.00 to replace that piece, but could not guarantee that it would be the only problem. The motor or some other issue may have caused the board. This machine was purchased at Home Depot on sale and at $450.00 to repair would be approximately 70% of the original price. It will be cheaper to buy a new one rather than fix this one. We were not happy with this machine in the first place. It leaves the clothes stained with a white powder that never rinses off. The cycle time is very long, up to an hour to wash a load. The clothes are still very wet once the cycle is finished, which of course increases the drying time. I cannot recommend Whirlpool top loaders after my experience with this machine.

Recently bought a 19-cubic ft French Door Whirlpool refrigerator. Seems to work fine at this point, but the compressor/cooling system has a fairly loud swishing noise it makes off and on during the cooling cycle. According to the owners manual, this is normal. If I had known this, I would not have bought this brand. Believe me, it is loud and you can hear it from all parts of my apartment. Also, once you examine the fridge up close, it really is cheaply made. Low-grade plastics for shelves and compartments. And this was not an inexpensive product to buy. We are talking out the door paying $2,000. Sad it is American made. My parents bought a Samsung last year and it is of much higher quality than the Whirlpool I have. But so far, it is keeping the food cold. Just wish it was quiet.

I replaced a 4 year old Whirlpool dishwasher with a new Whirlpool dishwasher on 01/18/2019. July 2020, dishwasher failed. Finally got Whirlpool to send out a repair technician and was advised that the sump and motor had failed. This is after only a year and a half. Whirlpool will not back their product because I did not send another $200 for a service plan. So basically whirlpool cant even guarantee that their product will even last a year.My 4 year old dishwasher had the same issue which is still unacceptable. I have a Whirlpool refrigerator that almost burned down my house and just replaced a failed Whirlpool stove with a Samsung. I wish I could say what I am replacing this dishwasher with, but I am too frustrated to even look for a replacement after only a year and a half. Replacement parts will cost $250 just for me to do it myself. Do yourself a favor and research the product. Should you spend more? I cant answer that. I have seen 20+ year old Frigidaire dishwashers still working. I honestly dont know what brand to get, but I do know that I will never purchase another Whirlpool product again, and neither should you.

I purchased the refrigerator/freezer, Whirlpool model GX5SHDXVQ02, 2 years 10 months ago. It is now not keeping the refrigerator portion of the unit cold or even cool. It is 70 inside the refrigerator although the freezer portion is doing a fine job. This unit is not even 3 years old yet! To top it off, the unit only has one year warranty on any part. The repair person is now here and replacing the control board. This piece alone is costing me $184.12. Then the labor hours and service call. I should have trashed it and bought a new, different brand. Not even three years old. My last refrigerator/freezer lasted 13+ years with no problems.

We bought a new Whirlpool refrigerator from Sears last summer --- and after experiencing some motor noise we thought this would be ok. We went away to Mexico for 4 months this past winter and this spring the noise seems to be much worse. It seems to have changed -- and we called Whirlpool and they would not help. They said we pay even though we bought this fridge less than a year ago. Consumers should be made aware that if your fridge is noisy you pay for any servicing - they only cover a malfunction. My fridge needs a professional to look at the cause of the loud motor noise.

The machine is reliable, does not take forever to do a load, it is relatively quiet. It has sufficient options depending on the size of the load. Additional options are time setting, choice of warm, cold or warm/cold water settings. On light and medium loads it extracts almost all of the water; on heavier loads an extra dry spin does the job. In all the years that we have had it, it has required only one service call. The maintenance man told us that this model is the best in a series and he recommends that we hang on to it for as long as possible. We're very happy with it.

To start with, the ice maker drips non-stop. I have to check it several times a day to make sure its not puddling up and running my hardwood floor. Because of the continuous that, drip, freeze cycle, it creates an ice dam around the rubber boot between the ice maker and ice bin....which they located in the door where there is inadequate cold, so the cubes melt, making even more of a mess, causing it to be unable to dispense them because it is one big mass... oh and that creates an ice dam also, so on top of replacing a torn boot a couple times a year I have to chisel out the ice bucket and defrost it once a week.Want more? The ice tastes horrible. I have no idea why. It didnt in my last refrigerator. The Tap water tastes fine, I disconnected the line running in to the ice maker and tried the water from there and its fine. So somewhere in the ice maker, something is wrong. There is more. The unit is a year old and now inside the refrigerator it smells like gamey shrimp. I have no shrimp in the freezer, fridge, not have I. I dont store anything in poor sealing containers, nothing has spilled, I removed all drawers, panels, shelves and scrubbed the whole inside with bleach/water. I changed every filter, checked the drip pan (clean), and still half-rotten shrimp smell.My last refrigerator was an Amana from 1986. I bought it used in 93 and owned it until I got this Whirlpool. Never had a problem with it. I have had non-stop problems with this over-priced Whirlpool and I guarantee it is the LAST Whirlpool product I will ever own.

Whirlpool Slide-In AquaClean Technology - My beautiful, modern oven is no longer. After 4 tries doing self-cleaning my oven was still dirty. I did have to wipe out the water (although I measured it) before I could take the scraper/sponge provided by Whirlpool to assist in the cleaning. Scraper bent - sponge disintegrated and I still have a dirty oven. Called service. My pleasant service tech informed me the water is only to reach 250 degrees! Really! My dinosaur of a Whirlpool cleaned fabulously! New technology has turned mine into an on your knees, scraping and broiling fool. Fool because I bought into the whole Aqualift Technology. We cannot use any kind of liner, etc. This slide-in may look great but the labor required to keep it that way is beyond this OCD person! So much for my efficient new kitchen. May the engineers who designed this technology be ashamed of this product. It is not even a self-steam cleaner!

This Whirlpool refrigerator/freezer Model W10314956B was purchased from Lowes on June 29, 2012. Recently noticed rust appearing under ice/water dispenser tray. Requested warranty service, but was told the problem was considered DUE TO WEAR & TEAR! TOTAL COP-OUT! There are NO MOVING PARTS in this area; how can there be WEAR and TEAR? To my mind, this can only be charged as SHODDY MANUFACTURING or INADEQUATE QUALITY CONTROL by the manufacturer.This appliance is only 6 1/2 years old! Consumers expect refrigerators to last much longer than that. The only possible cause for this problem is as stated above: poor quality control by the manufacturing plant, and I completely discount being told the problem was due to WEAR and TEAR! I will think long and hard before I ever even CONSIDER purchasing another Whirlpool product, and maybe YOU SHOULD TOO!One issue that keeps gnawing at me is HOW, since this is supposed to be a STAINLESS STEEL refrigerator, can it rust? The best answer I found on Google was that its likely due to insufficient chromium in the mixture of metals used to make stainless steel. To me this continues to point to shoddy workmanship at the manufacturing plant. I have pictures of the problem, but for some reason Im unable to copy them to this complaint. Probably because Whirlpool is afraid of pictures that confirm their shoddy craftsmanship!

I bought my house in 2009, and the previous owner bought this refrigerator in 2005. By 2012 The light and temperature read out went out. A circuit board had to be replaced. I have a home service company that I pay for yearly which takes care of the appliances. As usual, the fine print on the back of the contract said circuit boards were not covered. When I went online to purchase the part, the cheapest I could find it was $180. My service company said they would not cover it because they break down so frequently, with Whirlpool as the biggest offender. They gave me a discount and charged me $125 for the replacement. Whirlpool is making a fortune on these defective parts, which last long enough during the warranty period, and then you are on your own.In 2015, after the refrigerator was 10 years old, the compressor died. Hundreds of dollars of food spoiled. My service company said I was covered for the replacement, but I would have to wait 5-7 days for the part to come in. I was so furious that a refrigerator of this age would break down on me. The repairman told me he has seen these Whirlpools break down after 5 years. He said they are junk. When I was young, we moved into a new 20 story building in 1963. All the apartments had the same refrigerator made by Frigidaire. I lived there for 26 years. When I moved out in 1989, that refrigerator was still there working perfectly. It never needed a repair. I never heard anyone complain about theirs either. How is it that in 1963 a company could build a workhorse of a refrigerator, but in 2005, Whirlpool, a company in business since about 1911 makes this junk? I will never buy a Whirlpool product, and will tell the world not to do so as well.

My family has been without hot water for two weeks. We have the same water heater, we have been to Lowes where we were told the recalled parts were no longer available, unless we wanted to drive 3 1/2 hours to Arkansas to get it. Whirlpool wants to give me a free part for $36.00 worth of shipping and handling! All the local suppliers say I have to go through Lowes, or the manufacturer. I dont want to give whirlpool another dime. This has been a fiasco. How much more can a company disrespect their customer, than to make us pay for a faulty product replacement? It is unacceptable. This is ridiculous. It is December, and I have a family of 7, including a child in a wheelchair.

Good microwave and will have 1100 watts Of use for TV dinners and warm up food. Do well and goes well. Please use this as well to warm up TV dinners smaller than most. Test them and see what is best. Go.

I purchased a Whirlpool Refrigerator with French Doors, Model No. GX5SHDXVD03. Within 1 year and 4 months, I had to replace the defrost control board. I spoke to Whirlpools customer service, George ** said he was sorry for my inconvenience but that he refuses to help in any way because I missed the warranty period by 4 months. I spent $352.74 for the parts and labor and lost hundreds more in food. Do not purchase any Whirlpool products. I was told that the boards have been going out frequently.

Purchased a new Jenn-Air JCD2295KES in 2007 when we remodeled our Kitchen. Its been a decent fridge. When it quit a couple of weeks ago, I had the repairman come. He informed me that the HV circuit board was bad and sorry but they dont make them anymore. What, a 7yr. old fridge and thats it? I sort of expect things to have to be repaired or maintained but to have to throw it away because Whirlpool chose not to carry the parts any longer. I decided to scour the net and see if I could find this legendary board. Lot of places seemed to have carried it but could no longer get it from Whirlpool. I found a place that could supposedly repair them but after a few days, they called and said the microprocessor was not repairable.I contacted Whirlpool and they gave me a place that does obsolete parts and although helpful, I thought they were real opportunists and wanted to charge me considerably more for a reconditioned board that a new one would have cost if I could find one. I kept looking on the internet to no avail and when I called Whirlpool again I was getting pretty upset. Here I am with a 7-year old refrigerator and cant get parts for it, thats just not right. They were pleasant but basically their stand was sorry, theres nothing we can do. I told them that I bought a lot of appliances as I have quite a few rental properties. I cant throw an appliance away just because I cant get a part. It just doesnt make sense. I feel Whirlpool/Jenn-Air simply doesnt care. Im not interested in their excuses, I just want parts. I dont think it is unreasonable to expect to be able to obtain parts for at least a dozen years or maybe even a little more.I posed the question to them. Would you buy a $2000 refrigerator if you knew it would only run 7 years? The customer rep. said no she wouldnt. Well, Whirlpool, neither will I. I was unimpressed with their lackluster response and offer of a $300 rebate on a new fridge. I can find better deals than that on my own. I have purchased many appliance and always actually liked the Whirlpool line but Ill not buy any of them again. Shame on you Whirlpool for letting your customers down. Just because you can ignore me, doesnt mean you should. Im in business and I would go to the ends of the earth for a customer to make them happy. No wonder the Asian companies are kicking butt on the so-called American manufacturers. If your not going to get service you might as well go for the cheap price.On a final note, I did after two weeks of searching find a board hidden in a little appliance repair shop in Colorado. It should arrive here tomorrow and was priced $150 less than the reconditioned board that the gougers Whirlpool recommended. I believe it is the last board on the planet. Hopefully it will get my fridge another 7 years down the road and by then Whirlpool and its subsidiaries will have been sucked up by foreign companies and under a different label.

WTW4950XW2 - I purchased My whirlpool washing machine wtw4950xw2 from best buy in 03/30 2013 and it just stop working after 3 yrs. The manufacture warranty was only good for 1 year. I think companies does that on purpose because they know these new equipments are not going to last. I think before they use to have at least a 3 yr or better warranty on appliances. First it started making this loud sound when on the spin cycle, so I had a repair guy come out. He told me that the bearings needed replaced so (how does bearings goes out in 3 yrs). I asked how much will it be to replace parts/labor. The Parts cost $250 and the labor is $200. I might as well buy a new washing machine. I am so disgusted with this machine. My previous Whirlpool, which was not the new modernized, I had for at least 12 years and also I bought a whirlpool dryer. My Dryer stills works after 15 yrs. Im going to try to hold on to the dryer until the long haul. I wish I just would have gotten my old washing machine fixed. Now Im looking for a new washer and I wont be doing a whirlpool or anything with a push to start - just a plain old agitator, no sensing mechanism, just basic.

Ive owned the microwave for 2 years, and recently the DOOR AJAR alarm goes off whenever I try using it. The appliance is now essentially unusable. I wish I knew about this known defect before purchasing. I spoke with Whirlpool Customer Care, and they want to charge me to have someone come fix a known defect. The charge is more than what I paid for the microwave. Please avoid Whirlpool at all costs!

I have had our Whirlpool Cabrio washer and dryer (CU0771356 and MU0803512) for four years. Our trouble started when the machines were 14 months old. The numerous error codes have been fixed by replacing boards, the bearing has went out, and the entire tub has been replaced. The dryer has had two service calls for going out. Now, both are out again. The washer pump is bad and the dryer has stopped heating up. Where is the class action lawsuit?

In all of my 50 years of marriage and buying stoves, I have never had an oven breakdown. I live in Canada - I purchased three appliances, all Whirlpool 2 years ago. I had to have a service call on the fridge three weeks ago - a little rubber nipple was clogged up and water was running into my freezer. Bill $100.00 - two weeks ago, the broil element in my stove would not turn off when the bake cycle heated up. Actually, you did not have to press the fast heat button as the broil came on by itself. I have been waiting almost two weeks for the part - today I was told it would be another week. The part has to come from the US - what ever happened to Whirlpool Canada???? - I am told the bill will be $350.00 and maybe more plus the service call. I do not find this acceptable. What do you do when you have already invested the money in the product. Bring back the old Moffat stoves. I would like to be reimbursed for the money I have put out and will put out.

My Cabrio was built in April 2016, its now Feb 2019, and its not working. Shows error code of LF, the inlet water value is bad. I bought a Sears protection plan, repairman comes out, tells me no-one has the part anywhere, its backordered and no way to know when it will deliver. Sounds like a scam so Sears doesnt have to fix it and Whirlpool makes little to none of the part so you have to buy a new machine. This machine also takes forever to wash clothes, sometimes part of the clothes come out dry because not enough water. Its a huge tub, but of no use because theres not enough water to clean properly therefore, you have to do small loads. I always put it on high water because the other features like, quick wash & normal do not give but only little streams of water! The first one I had delivered made a funny noise from day one so Sears replaced it the next day. This one has NOT even lasted 3 yrs. There needs to be new legislation placed upon these companies with regards to the products they make. It should be illegal to make such junk and be able to charge high dollar for it and it doesnt operate well or last very long. They are laughing all the way to the bank on everyones dollar, intentionally making products that last less than a few years! I Will NOT purchase Whirlpool or any of their products again! They owe me a new Cabrio and Im going to make sure I get it and get my moneys worth! DONT WASTE YOUR HARD EARNED MONEY ON THIS JUNKER! DONT BE FOOLED BY ITS PRETTY SLEEK LOOK.

Whirlpool washing machine M# wtw7340xw2 / S# c14270996 - Bought in 11/26/2012. Never was real satisfied with the way the clothes were washed. They never came out real clean and smelled like there was still soap in the clothes. It has been less than two years and now it will not run. Turn the unit on and all it wants to do is turn on the pump to drain the tub. Im a refrigeration technician and know how to run a diagnostic test Whirlpool has for this machine. I get an LF code which is water long fill so I checked out the water tube which is ok. So the problem is in the circuit board not sensing the water level. To replace this board is around $350 dollars and if I had someone else do the work I would be looking at over $550 dollars. I only paid around $500 dollar for the washer so it does not make any sense to put a new solid state board into this washer which cost as much as the washer. Our old GE washer lasted us for over 20 years and did a better job washing our clothes. There should be a better warranty on these machines than one year. I did not buy the extended warranty because of the cost and I expect that the product should last at least 10 years or more.

We bought this dishwasher 3 years ago and have had nothing but trouble with it. Our friends bought one just like it the same day. It basically runs when it wants to. It has really been a pain. We also bought a refrigerator about the same time. The ice maker builds up frost and you cant get the ice to dispense. We are very disappointed in these products. Had a Hotpoint dishwasher that lasted 25 years and was still working when we replaced it with this one. Our Amana fridge was still working when we replaced it. Just needed new seals.

The Whirlpool range #GY398LXPQ00 is four years old. This is the fourth major problem. Oven overheats and will not function. I set it at 350 and the bottom coil and broiler both came on and overheat quickly. This is the third time with same problem. I am going to have enough invested in repairs to buy another range. I shall never purchase another item made by Whirlpool or any of its affiliates. That leaves me with Samsung or Bosch, I think. The people are very curt and offered no help at all so calling them is extremely useless. This range is definitely a lemon. Too bad, there arent avenues to make them replace it. I am angry, disappointed, and disgusted. Are you listening, Whirlpool? Never again. May your company go down the drain.

Whirlpool WRF992FIFM00 - Purchased new April 2017. Its October now. Service has been called 7 times so far. Ice maker has not worked since day 1. Fridge leaked all over the interior around the third month. Compressor went out in 5th month. Compressor replaced 2x so far. Every component piece was replaced on 5th month. Still no ice. As I write this compressor getting ready to go out yet again. Paid almost $3000 for this piece of crap. On first name basis with technician. He tells me that his guys work on this particular refrigerator CONSTANTLY. So far I have lost over $1700 in food and wages (leaving work to meet technician). Currently battling Whirlpool. My next step will be legal action if they do not refund or replace this stainless piece of garbage.