GS6SHEXNB02 Whirlpool Gold Refrigerator - Bad ice maker module. Ice maker valve is bad. Its gone out 3 times a year since I got it. We order a replacement, it goes bad again. Its not the ice maker itself, its a bad valve. Signs its going out, ice maker stops making ice or the ice cubes are small or the refrigerator water will start pulsing coming out (start and stop). Whirlpool made a bad product and they know about. Several complaints online about the ice maker no longer making ice. Bad product.

My Whirlpool has been in use about three years. It was purchased on sale at a very reasonable price. My only complaint is the heat dry function which somewhat fulfills its purpose, but I usually have to hand dry some dishes. Overall, it is an average dishwasher that gets the job done. The best feature is that it is very quiet; you barely notice that it is running.

I have always had Whirlpool Everything - not anymore!!!! I purchased a water saver washer that I am very unhappy with - it does not get the clothes clean. I have to put it on an extra rinse (water saver?) to get the soap out. I use the Tide for HE washers. I cannot wash a large load in it - directions say I can. Anything too heavy or bulky will not spin out well. Will bounce all over the place. From now on I will switch to another brand. They push so hard to buy a warranty because they know you will have trouble! Should have read the reviews!!

My Calypso washer is broken AGAIN. I have spent more in repairs than the machine cost originally. After more than a dozen emails to customer service they have still not answered me even once. Its obvious they put as much pride in their customer service as they put into the assembly of their products.

We purchased the Whirlpool refrigerator on July 9, 2012. Refrigerator was replaced on August 23, 2012. Since then there have been many, many service calls. I wish I had kept records to be able to tell you exactly how many times, but we purchased an extended warranty. From memory, I can tell you the ice maker has been replaced twice, new doors have been installed for refrigerator and freezer (replacing ice maker a third time), then within the last three months the freezer door was again replaced (replacing ice maker a fourth time). The gasket on the freezer door has been replaced. At one point the refrigerator was colder and freezing and the freezer was not freezing. Parts and pieces have been repaired on several occasions. The inside of the freezer door next to the ice maker is still frosting up and yet again the ice maker is not functioning and needs to be replaced a fifth time. In other words this Whirlpool refrigerator has been a lemon for us. Finally, we figured it out. There is a fairly large gap at the top of the freezer door between the case and the gasket. If you run your hand across the area where the gap is, there is definitely a dip in the face of the refrigerator case where you can see the top of the ice maker. A picture showing the gap is attached. I am not sure that our purchasing a store extended warranty was fortunate or not. My husband has insisted on repairing this thing over and over and over because of the extended warranty. I think repairing it is futile and the only people being punished by all the repair calls is us because we frequently do not have ice, we are losing food because of freezing or not freezing or cooling or not cooling as the case may be. Thank God, the warranty expires in July and we can repair this Whirlpool by replacing it with another brand -- not in any way associated with Whirlpool. If you Google Whirlpool, you will find that Whirlpool is affiliated with almost every other brand of refrigerator and really limits your choices. Based on my experience with this Whirlpool refrigerator, I will never purchase another Whirlpool or any other brand associated with the Whirlpool brand. The myriad of repair persons in my home probably find a Whirlpool refrigerator is job security for them.

The stainless steel refrigerator door is rusting after only 5 months and the company respond it is cosmetic and we the customer have to live with it.... They will send a cleaning product which didnt remove the rust. Review that was written on the company facebook page wasnt published because it didnt meet the company website guideline. Its disappointing and frustrating to realize that we have to go through it. Not happy with customer service.

The agitation is too loud. I called Whirlpool customer service and said I wanted to return the washing machine because it was so noisy. Whirlpool customer service agreed that it was noisy and said they would send a technician out. Whirlpool customer service never told me the technician they were sending would cost me 25% of the washing machine cost. The technician said this is normal all machines are this loud. Now I am out the cost of the washing machine plus the cost of the technician and all I have is a very noisy washing machine. Im a real satisfied customer. The machine was bought 12 days ago.

My washing machine is just over a year old and it has ruined so many clothes... They come out with brown stains on them... Almost like a oily stain. Not sure where its coming from but its either Im gonna have to buy a different machine or keep buying clothes. My husbands t-shirts look terrible... If any suggestions to what it can be please respond back to me. Thanks. Model# wtw4815ewo. Serial# c51433710.

We had our microwave and stove delivered in October, 2015. We had 4 deliveries of the microwave. The first two were damaged, the third needed a new fan motor and the door was not straight. They wanted to send parts to fix but we could not see spending all that money for a brand new microwave to have parts put in. I complained a lot to both Whirlpool who would not replace it and ABC Warehouse who finally agreed to replace it with a brand new one. The 4th is good. (so far).Our stove has a flaw in the glass top, the drawer doesnt close properly, and there is a piece of metal sticking out from the lower right side of the oven door. ABC says they cannot do anything about it and Whirlpool says it is under a parts warranty so it has to be repaired. I even spoke to supervisor Kimberly at Whirlpool. Got same answer. We are very angry and disappointed. As I told the Kimberly, Whirlpool got every penny they asked for. We paid for brand new in perfect condition and got a stove that needs fixing. We will never recommend Whirlpool as a Company for appliances and based on all the negative reviews Ive read, neither will a lot of other people.

I have read the reviews and agree with all negative comments. There is no point in investing in a high efficiency machine when I have to rewash many dark items several times in spite of always adding the extra rinse cycle. The clothes appear cleaner if I do not add liquid fabric softener, but as I prefer to use my clothes line when possible, I am unable to use fabric softener. Also, although it is supposed to be a high capacity machine, I only fill the tub about one third of its capacity, hoping this will increase the cleanliness of your clothes. It doesnt seem to help.I have contacted Whirlpool several times and the final suggestion was that pay for a technicians visit, approx. $100, plus extra for repairs. I have decided not to throw good money after bad and to buy another brand of washer. This is the WORST appliance I have ever owned even though it is supposedly high-end. PLEASE do not buy a Whirlpool appliance. If the Cabrio washing machine is an indication of the quality of their appliances, you will be wasting your money.

I bought a brand new KitchenAid stainless steel refrigerator for close to $3,000.00. It has a big crack in the back casing which Im sure is affecting the seal. It is still under manufacturers warranty. Whirlpool sent out a technician to put a yellowish plastic epoxy to seal the crack. When I told him that this was unacceptable as it dries yellowish and has a dull finish he explained that that was all Whirlpool was willing to do.I have been dealing with Whirlpool for 4 weeks now and they refuse to repair the crack and they deny any manufacturing defect. I have sent them pictures of the crack and they still refuse to resolve this issue. Very bad, horrible experience with customer service, long waits on the phone, rude and ineffective employees. This CLEARLY is a company that will not stand by their product and I recommend everyone to CLEARLY stay away from purchasing any Whirlpool products. They will be paying a lot of money for very poorly manufactured products.Please, please, do not purchase Whirlpool products! You will be happier spending money on a company that values you as a customer before and after the sale. Obviously Whirlpool would rather forget you after they have sold you their product and have their money. Thank you for reading this. I hope I have saved potential appliance customers from making the same mistake I made. DO NOT BUY WHIRLPOOL!

I agree with the comments already made. My crisper drawer plastic rectangular piece just literally decomposed! It shredded into little pieces and cracked and broke, dropping one side of the draw set. I called about it - nope, not under warranty - replacement cost? Merely $150 so my drawers could be in the refrigerator. Also, because of the stress of the angle the drawer holder was when it broke, it cracked the drawer at the back - and the drawer had one grapefruit in it at the time. (Not considering replacing - cant imagine what that would cost when the little brace piece approx 14 was so expensive.) The flap - yeah, it split. I am a single person, no kids EVER in my refrigerator and I travel so much that I am barely home 20% of my days. The refrigerator gets very little activity opening and closing the doors yet the flap sliced. HOW DOES THAT HAPPEN??? With any break in the seal as they called it, the refrigerator starts collecting moisture inside (and I live in the desert so we have very little moisture in our air) and drips or starts causing frost build up on the icemaker. Yesterday, once again, the icemaker stopped working. When I asked about replacing the flap I was told the entire seal needed to be replaced @ the cost of $232 PER DOOR!! Right now with just the plastic rectangular piece and the bar between the two drawers (BTW the rollers on the frame are not included with the frame purchase they announced) I have $614 in repair parts WITHOUT fixing the icemaker! Last night water was running in my refrigerator from the icemaker. I WILL NEVER BUY OR RECOMMEND WHIRLPOOL TO ANYONE EVER AGAIN. I have been a Whirlpool ONLY customer for over 45 years!!!! They told me that I had to schedule an appointment with a service person at a minimum of $100 cost to me - JUST TO FILE A COMPLAINT with Whirlpool! They only take complaints from service people submissions. I advised the Whirlpool representative to start looking for another job because if this was the way they treated lifelong customers, her job may be eliminated due to No Customers! Does Whirlpool seriously NOT CARE about their customers? #WhirlpoolSux #WhirlpoolRefrigeratorsAreMoneyPits #WhirlpoolDoesntWantCustomers #WhirlpoolDeservesToGoOutOfBusiness #DontBuyWhirlpool #WhirlpoolFrenchDoorRefrigeratorsHorrible #NoServiceFromWhirlpool #WhirlpoolDoesntStandBehindProducts

This Whirlpool, two door, refrigerator with ice maker & water, replaced a very poor quality 'LG' refrigerator which had stopped working. The company, "LG" was not interested in learning what the problem was but was only interested in making sure we understood the fee for an "LG" repair person to come out. The set fee was a minimal of $150.00 without any repairs. We decided to toss the LG and went to our local Home Depot and purchased our Whirlpool that same day, on sale! Our Whirlpool has been working great, without any problems and the fresh, filtered water is always refreshingly cool. We would very highly recommend Whirlpool! It seems their products always work very well!

I had problems with the door closure on day 3 of my French Door Refrigerator Model # WRF560SEY. The flap on the left door that seals them fails to fold back if I open the right door first. Which didnt seem like a big deal until I tried to close them and have to remember to close the left door first or itll bang against the right door and Im afraid itll break that piece off then the refrigerator is worthless. The manufacturer drop shipped a new piece, after several attempts of adjusting the closure, and it still does not work. I have written Whirlpool and am told they have a new door on order but it will take 6-8 weeks, that was in March. Now when I contact Whirlpool no one ever returns my calls or emails. I have had the refrigerator only for 15 months and I have fought with either the store or Whirlpool since the third day of owning it. No one cares as long as the appliance is paid for. I will never buy another Whirlpool appliance.

Same as others, We purchased a Whirlpool Cabrio Washer and there is a bearing problem (which seems to be the common issue reported). The washer is unusable at less than 5 years of age. The repairman told us its a bearing problem and its common for this to happen to the Cabrio. How can an Whirlpool get away with selling a defective product?

Whirlpool Cabrio Platinum Washer Model WTW8800YC1 - I bought the Cabrio washer and dryer pair about 2 years ago at Lowes. About 5 weeks ago the lid fell apart. The hinge area came loose so now there are three pieces to line up (glass lid, metal arm, plastic frame), the fourth piece fell off completely. If you are successful at lining them up you can push the lid down and set a weight on it in order to wash. My first repairman said it was common issue. He expedited a lid. Three weeks later I called to find out when it may be repaired. He said he hadnt gotten the part from Whirlpool. I called Whirlpool... nice lady told me the part was on back order but should ship the first of the week. So on week 4 after not hearing anything I called a new appliance repair person. It is going to cost about $280 dollars to repair. This is one third the cost of a new washer??? I fight with this machine every day to get it to wash.

Cabrio Washer WTW660SW2 - For 2 years I have been getting f1. When I talked to Whirlpool they said they were not aware of this problem. Now I have to pay to fix it. Looked online thousands are having the same problem.

About three months ago the freezer iced up. Tech showed up stating that the motherboard went out, needs to be replaced, had to wait 6 days for part to show. Was replaced. Two weeks later freezer iced up and refrigerator got hot, lost a lot of food. Again motherboard went out again, had to wait another six days. Part came in Tech replaced the motherboard and installed a heater defroster. Worked for 2 weeks and now the freezer is icing up again. What a pain in the ass.

We purchase Whirlpool fridge less than a year ago. Its still under guaranteed. 2 months ago we notice the fridge part heating up and food was going off. I went back to the shop where we purchase the fridge. They said we had to contact Whirlpool direct so we did had to wait 3 weeks for someone to come and look at it. Fridge is not repairable. Fella who came out did not report back to Whirlpool. I was waiting and waiting to hear word. I rang to see what was the story on it and eventually they said O we will exchanged your fridge and we will ring you on delivery date. Now Im over 2 month waiting on a fridge. Whirlpool is a joke. The company should be put out of business for what they do to honest people buying their stuff, and people who are in the same boat as me should go to the high court and sue them for all the stress they put people through. Shame on you Whirlpool. Disgrace.

My electric stove is only four years old. In December, 2021, the control panel broke. Digital read out - numbers can’t be read. Service said it is control panel - can’t be found anywhere. Oven has caught on fire twice. House full of smoke. Whirlpool stated my first mistake was not calling them first. I dont have warranty and couldn’t afford a service call so I have DTE protection plan. They sent about appliance repair at their cost. Man said it is control panel and NONE can be found. Whirlpool can’t send THEIR serviceman for another two weeks. I was told to keep circuit breaker on stove pulled. I am 76 and my husband is 84. We can’t go out to eat every night for two reasons: we are on a fixed income - finances will not allow. Plus we both have health issue so I have to cook/bake a certain way. It is going on three months. We can’t afford a new stove every four years. I want Whirlpool to work out some compensation for my stress, aggravation, loss of bakeware that burned in the oven. Took us two days to clean the oven mess, including the glass door - don’t know how it didn’t explode. We had to run downstairs- at 84, moving fast is not that easy, to pull circuit breaker. I could not make two birthday cakes that I had committed to. Can’t bake or make casseroles. We need help of some kind.

This machine cannot handle washing jeans, towels, blankets, pillows or anything bulky or very small loads. The load becomes ul unbalanced almost every time I try to wash a load. It has never gotten things very clean.

3 months after I got the fridge, the ice maker went out. 3 months later it started to work again. Replace the water filters 2 times per yr. It is noisy when it makes ice.

Handle needs smarter design. I purchased model #WRT311FZDM00 in November of 2015, didnt install in my new home till December. I am a single senior female, so there is little wear on the fridge, unlike a family of several people and with kids. The door handle actually broke just behind the screws that hold it in place, the plastic part of it broke into a couple of pieces. The cost to replace this handle is approximately $80, which is ridiculous in my opinion. Please start making things of quality materials instead of cheap plastic, especially at a stress point of a part. Even I know better than that. All 4 of my major kitchen appliances are Whirlpool, as well as my washer/dryer. I thought I was buying quality products. Hopefully things will hold up better with the other ones.

In the last year, I have had to put in two sets of parts to my Whirlpool water heater (thermocouple) within three months in between each malfunction. Now the hot water is out again, and I need to have a plumber come and reapply new parts to the hot water heater. Whirlpool is refusing to send new parts to the less than a year old hot water heater until they speak with my plumber. It was purchased in December 2011. I am a disabled senior citizen, and we have not had hot water in over a week. Meanwhile, the weather is in the teens and has been snowing. I live alone and have not been able to wash dishes, take showers or mop my floor. Being a diabetic, cleanliness is very important to maintain good health. Living on Social Security, I cannot afford to replace my water heater parts every few months and my health cannot afford to not have hot water. Model number for this Whirlpool water heater is N30T61-303; the product number is 0733315.

Bought a Whirlpool fridge in a package from Home Depot three years ago. The fridge has already stopped working. It started having issues about 1 1/2 years in to owning the fridge and finally died 2 weeks ago.

Bought Sep. 2012. April 2016 stopped cooling. Four visits over 4 weeks, various parts replaced, coolant refilled. Stopped cooling again soon after first 3 visits. After 4th visit cooled moderately (42 degrees) for 5 weeks. June 24, renewed service contract for 1 year for $112. July 12, stopped cooling! Took 8 days for service person to arrive; 5 days for him to tell Whirlpool that repair needed 5 parts, one of which is no longer made! But they sold me a service contract?? 16 days after initial call, Whirlpool says my case is in adjudication, which will take 7-10 business days. So I wont know what they are offering till Aug. 8th-11th. Four weeks living out of a cooler. The product is rotten, and the service is worse.Just recently discovered that all this time when I thought I was talking to Whirlpool, it was actually sub-contracted to AIG. Yes, the AIG that needed a massive government bail-out. Whirlpool customer service refused to talk to me; referred me back to AIG. The only other all-refrigerator (no freezer - I have a 20-year-old Sears freezer in the kitchen that works just fine) I can find is an inch too tall for the space. But I plan to spend for my handyman to raise the cupboard floor above, rather than buy another Whirlpool! Most of May, four weeks in July/Aug without a fridge. Hours on hold. The first service firm they used was incompetent, couldnt find the cause. I wonder how much of my $1,353 purchase cost, and my $112 service contract theyll refund?

Purchased a 450.00 Whirlpool over- the-range microwave oven in October 2015 and on January 4, 2017 it is not heating. Timer, light and turntable is working properly. I thought I was buying one of the best products. I was sadly mistaken. So I am a very disappointed senior citizen, is has a fixed income. I still have the receipt from my purchase from Lowes.

Stainless steel side-by-side refrigerator (4 yrs. old) - I have to continually clean the rust stains. Ive used the products Whirlpool has suggested and the rust continues to appear. Lowes extended warranty does not cover this problem because it is cosmetic; Whirlpool reps say its due to the coastal area where I live and that they cant do anything about it! I understand that there are many customers experiencing the same problems with Whirlpool products. Their customer service is worthless and is their warranty to stand behind their products!

Once again I am disappointed in a product that I felt was of the utmost quality. However after buying in 2010 and not being installed until 2011, the over the oven microwave has a crack on the outside of the door. Two pieces have fallen off from under the plastic rim on the inside of the door, two pieces of the door one on the top right side and the other on the bottom right side have fallen off. All I have to say is the two Whirlpool products I bought at Lowes has been a huge disappointment especially since the other two bought from the same stores are Frigidaires and work beautifully...

In 2013, my husband purchased a Whirlpool Hot Water Heater model #E2F40RD045V 40 gal. from Lowes in Vancouver, WA. On 12/12/15, had to call a plumber, the hot water heater was intermittent hot/cold. He flushed it, checked all power connections and changed the elements. On 3/18/16, NO hot water. Having a 6 year warranty, I called Whirlpool. They gave all kinds of excuses and told me to try a bunch of tests. By the time I got back to call them they were closed. I called them again on Monday 3/21/16 and said nothing worked and it had popped the breaker. They said change the elements. I told them I had just changed the elements 3 months before. I told them it was faulty wiring. They said the top element must be faulty. I gave up at that point and called the plumber. He came right out the next day. I had purchased a Rheem hot water heater to install and asked him to check the Whirlpool hot water heater elements he installed before he removed it. That is when it was discovered that under the insulation around the bottom element it was all scorched from FAULTY wiring. I called Whirlpool again and told them I could send them a picture and they said dont bother and immediately gave me an RA to return the hot water heater to Lowes. I told them I had already purchased another hot water heater and it was not a Whirlpool. I am going to request a refund.

We have had nothing but problems out of our refrigerator in the past 5 months. We purchased it a year ago in April and they have already replaced 7 parts on it. It still doesn’t freeze, and we have no ice... We will NEVER buy another Whirlpool product ever again!!!

I made the mistake of buying a whirlpool product and was wondering if there is a support group for angry unsatisfied customers? I have owned a duet washer and after 2.5 years is giving F1E2 error and is junk.

Its a big buy to decided on fridge, bought one last year and the drawer keeps popping off the plastic piece. Who designs these to where the piece isnt long enough to stay put. The Veg filter in the back came broke so it doesnt stay on. Just upset to pay that much and have a really cheap product.

Ive spent more repairing this washer than what I paid for it new!!! Its really ridiculous that Whirlpool isnt more responsible for their equipment that doesnt stand up to their name! Ive replaced more things than I want to type but just to start the computer board, pump, bearings just to name a few. Each time I had my repairman out it was a minimum of $300 to repair. Ive had my repairman out 5 times to repair things. Thinking each time its cheaper to fix it than buy another which I surely didnt think I would be repairing it several time! At this point Im just sick to death that a washer that is for a home of myself and my daughter has broken down so much. I cant imagine what a family would go through. Even after all the repairs it still isnt right but Im done sinking money into this sinking ship of a washer! Its loud constantly stops due to un level so I have to move the clothes around usually having to repeat this several times before I can get the load to finish!!! Then they come out wrinkled more than they went in and I have to iron clothes. A person should NOT need to iron! May as well wash them in the river on a rock. It would be easier!!! SO DISAPPOINTED!!!

Whirlpool WRF993FIFMOO: Refrigerator Problems: the doors do not close, both ice makers went out, The computer on the filtration will go off. Refrigerator had problems maintaining temperature since 8.12.17. The refrigerator no longer works. This is my second unit since 11.09.16. It came from nfm.com.

When I first bought this machine I loved the big tub, but I was concerned that there was no agitator. It confuses me how clothes can get clean if there is nothing to rub them again. Even in the olden days they rub clothes against a board. Well my concern is valid and I believe the washing machine industry needs to go back to the old model, as this new version does not work.Here are all the problems: 1) The machine judges how much water to put in. This doesnt work. I follow the directions and outline the perimeter and dont overload, yet still it just barely puts in enough water to make the clothes wet. Im all for conserving the environment, but enough water needs to be provided to actually get the clothes clean. I would like to be the judge of how much water should be used, so I would like to be able to tell the machine if it is a small, medium or large load. I do believe that the lack of enough water is why the clothes do not come out as clean as they should and why they end up smelling (see #4). 2) There is no agitator, so there is really nothing available to help clean the clothes. Spinning them around like a maniac is not enough, which leads me to the next problem. 3) The clothes come out twisted terribly and then many times come out of the dryer wrinkled because of how hard they were twisted. I tried to select a less harsh spin cycle, but then the clothes are too wet to put in the dryer. There is no happy medium.4) Biggest problem to date: Our clothes/towels have all started smelling. You know that smell when you leave your clothes in the washer too long (like two days) and then put them in the dryer? Its that smell. The clothes/towels dont smell when you immediately take them out, but they do smell at any bit of moisture. When I dry myself off after the shower, I notice the newly washed bath towel smells like a wet dog. I have used the pods, liquid detergent and powder. I dont remember having the smell problem when I first bought the machine and used powder, so I just returned to using powder today. (Ive even tried doubling up on the pods, but the clothes still smell.)This leads me to problem number 5: When using powder in this machine, the machine does not empty the powder container completely, and so the clothes do not get the required amount of detergent. Often there are clumps left over in the powder dispenser, but not always. (This is what led me to go to the pods and liquid detergent in the first place.) But at least with powder (I use Gain) my towels dont stink after the first time I used them.I wouldnt recommend this machine. I really researched machines before I purchased this one, but they all had bad reviews, so how do you pick? And I never look at the good reviews because we all know so many people are paid to rave about products they know nothing about, or it is a company employee writing the review. This machine is a huge disappointment. I am going to try adding a rinse cycle like a previous reviewer suggested. Maybe the extra water will help with the smell. Of course this is not good for the environment though, so this whole way of making washing machines with no agitator and limiting water defeats the energy efficient goal.

The first Front load Whirlpool washer leaked. 5 repair techs visits. Wasted days. Finally located the leak, in the main basket. Replaced washer. Second washer the clothes come out smelling like a horse blanket. Mold. Clean the washer every month still mold. Plan on junking the washer a getting a new model. Never expected this much trouble and time on a basic appliance.

I have a Whirlpool suite. Stove is fine...refrigerator is awful. Froze all the food in fridge. Cost me 100’s to replace. Put in new thermostat. Now sounds like a freight train. Bought in April and the filter already needs to be replaced to the tune of $81.

Whirlpool hot water heater - The water coming from the faucets when it is hot is red. Therefore, I contacted Whirlpool and was informed that the anode has failed. The anode is not covered because, according to this company, it is not considered a working part. It baffles me that the anode is not a working part since it keeps the tank from rotting. I have only had the hot water tank for three years and this part has failed causing my hot water to be red. Since this company contradicts itself, I either have to live with red hot water (rust) or replace the part on my own. Unlike your company, Lowes has customer service. They apologized and will be paying for half of the expense for the part. Unfortunately, I still must pay for an employee to replace the part. This whole situation is absolutely ridiculous. I will never be purchasing another item from your company and in addition to that, I will tell everyone I know to avoid this company at all costs. You should strongly consider revising this policy before you lose all of your customers.

New range and the faceplate keeps melting. Had it fixed once and it is melting again. I have been trying to contact Whirlpool but to no avail. What is my next step and is anyone else having a problem with this.

I bought a whirlpool cabrio with high hopes. Unfortunately, it has been the worst washing machine I have ever had. Then I moved in with my fiance and he too had a cabrio. It too is a piece of junk - and brand new! Every load comes out with left over residue and the clothes look worse than before they went in! I have tried everything and I do mean everything! IM 41 y.o. - IM well aware of how to load a machine. I load it just the way the instructions say: as if there was an agitator there. Ive tried using no laundry detergent or fabric softener - clothes still come out disgusting. Ive made sure the screens are clean, doing extra small loads, turning on the extra rinse, everything! Ive called whirlpool, but there is no such thing as customer service anymore. They just blamed me for not loading the clothes properly and blew me off. The machine becomes unbalanced very easily (it is leveled on the floor), sometimes the clothes are still soaking wet at the end of the cycle and sometimes all knotted up. This is a horrible machine!! I wish I could say it makes me feel better that IM, by far, not the only one having issues with this piece of junk!

I bought a Whirlpool Partner II 5 and a half years ago. It was always noisy and took very long to run a cycle. It started to malfunction after 2 years. We bought a new computer for it and a new control panel for the touch keys. It still kept not running a cycle fully. We found a YOUTUBE video that showed how to reset the model by pressing a combination of Normal and Heated Dry and that seemed to fix it for 2 years.It has stopped working again. Now it seems that the heating element is out. It doesnt clean at all, a scum film has covered the inside of the dishwasher and even mold spots are appearing. Ive had to wait extremely long times on hold to talk with an agent. My option is to hire a repair tech to come out and repair it and I pay for the parts. Seems like a bad deal since Ive already spent over a hundred on repairing it and a lot of hours. I will never buy a Whirlpool brand appliance again.

I purchased this Refrigerator Model #wrb322dmb, bottom freezer, 21cu ft. last year on July 3, 2015. In September I noticed rust spots on the top door. I called Home Depot where I purchased and they directed me to Whirlpool. I did purchase an extended warranty with Home Depot. Whirlpool did replace the top door. Thought that took care of it. Today one year and two weeks out of warranty, I again notice rust on both doors. Called Whirlpool. They said too bad out of warranty, not considering I had a previous report of this very same issue. So since I am very unsatisfied with this result and the fact that an expensive product is rusting, I decided to share to try to prevent someone getting stuck. Stainless steel is not supposed to rust which leads me to believe that it is not Stainless steel, but a Stainless Steel finish and not a very good one. So I am stuck with a rusting $1200.00 refrigerator only after one year. I have always purchased Whirlpool, but no more. They lost a 40-year customer. I have always bought American made but no wonder people are not buying American made any longer. TO SUM IT UP WHIRLPOOL STAINLESS STEEL APPLIANCES RUST! DO NOT BUY!

In 2007 our Whirlpool 30 gallon gas water heater began to have issues. Serial number 0425126675, Model Number FG1F3030T3NOV. The pilot light kept going out and would not stay lit.. After several times with replacement parts being sent with the same thing happening, finally in 2010 they replaced the water heater. A new water heater was professionally put in, serial number 1023T412357 Model number BFG1F3030T3noHV.I am having the exact same issue and I was told that the warranty was null and void on the new water heater because it was a replacement. They replaced a defective water heater with a defective water heater. I called the number given to me by Lowes 1/877/817/6750. I spoke with Nichole. I told her that I should not have to pay for replacement parts for a defective water heater. I told her that I was never informed that there would not be a warranty. I live on a fixed income and cannot afford to buy another water heater because I was given a defective water heater in replacement for a defective water heater. I became angry stating, Thanks for nothing and I hung up. So many people have the same problem with these water heaters that something MUST be done.

I have a combo Microwave oven/oven GMC275PDS07. When the microwave is finished with the requested program, the end of program chime lets you know its done. Then, if the door is not opened for at least 3 seconds, the chime will ring again every minute thereafter ad nauseum. This will go on for hours without end. I know because I tried it. I reached out to Whirlpool via a web chat and my question was not even addressed. I was ignored. From reading other submissions, I assume this is de rigueur for Whirlpool. I then called Whirlpool and spoke to Katie in Tennessee. She was not able to bring up any make or model when I provided her the numbers exactly as listed on the inside of the door. She was not able to provide any respite from this annoying feature.This a Whirlpool Gold model, presumably the top of the line, in my book I will never purchase any Whirlpool product of any type and I will make it a point to let anyone who will listen that Whirlpool is not a manufacturer that takes its customers concerns seriously. Katie then advised that she looked up this feature and told me there is no way to turn the beeping off. I find this amusing since she could not find the model or serial number when I gave it to her.

Purchased a new Whirlpool washer and dryer at HH Gregg about 4 months ago. We complained to HH Gregg that the low water washer wasnt working correctly. It will only get about an inch of water in it causing buttons to be torn off... just beating up wet clothes. HH Gregg told us to try a few things. When we went back to HH Gregg with the same complaints they told us it was too late and call Whirlpool. Serviceman came out and said everything was fine with the machine, we just need to load more clothes! We are only 2 people, one of us wear a uniform and needs washed when we may not have a full load. Called Whirlpool to complain again and they said there wasnt anything they would do except send out another service person for a second opinion, which just means taking more time off of work. HH Gregg talked us in to this type of low level washer. We are still making payments on it!!!!

I was so excited for this stove top and oven - Whirlpool Gold AccuBake (especially at the price we paid for it!). Weve owned it for 13 years now, and in that 13 years, we have had to have the computer replaced 6 times now. The latest replacement being last week (Friday). The oven is still making clicking noises like the igniter wants to start and it is frustrating and annoying. It will do this for a 3-hour stretch numerous times throughout the day and night. Had a repairman here last week and he replaced the computer AGAIN! But the igniter clicking noise continues.

This is my third Whirlpool refrigerator. The first two lasted about 20 years each, and although not fancy, they were always serviceable. This one is different.Because of my kitchen cabinets, the only refrigerator with as much storage capacity (cu ft) as my old one was what seemed to be an almost identical Whirlpool, with the only exception being a slight difference in the ice maker. But this one is a disaster. The water/ice dispenser has been changed to one with one space only for your container. The water that comes out is warm, because the routing of the tube has been changed and it no longer goes through the chilled refrigerator space; the ice pours out so hard that usually half of it lands on the floor. In order to operate the dispenser using anything with less than a 4 diameter, you need two hands: One to depress the lever behind your glass and one to hold the glass farther away from the refrigerator. Failure to do that results in a wet mess. After dispensing crushed ice, it continues to send small pieces flying long after I change the switch to cubes. But that is the least inconvenience. In an apparent engineering change to meet energy efficiency, the new refrigerator recycles air from the freezer to the refrigerator compartment. That and other changes in the frost-free engineering have resulted in:Uneven cooling in the refrigerator. In fact, it froze $1800 worth of insulin pens. I was advised by the Whirlpool representative that I shouldnt have put them on the shelf where the vent from the freezer spews out freezing air. Spoiled food in the freezer. Everything in the freezer develops a thick coating of ice crystals within a short time. This dries out the meat, shrinks the popsicles, and destroys the quality of fish and fowl. At this moment, I have two pork chops that defrosted in a plastic container on my kitchen counter. I bought them fresh, and now the 10-12 oz. of pork is swimming in over 1/2 c. of water.Interior fittings are poorly made and shelves and drawers do not work easily. The allegedly stainless exterior is difficult to clean, and many reviewers have remarked that they find rust within a few months. I could go on. There is more poor engineering, and an array of noises filling the kitchen, but you get the picture. I wish I could trash this refrigerator and buy a good one, but that isnt feasible both because of budgetary and space constraints. The last service person who came out sighed and told me that the refrigerator was cold, and that meant that the unit was operating okay! I HATE this refrigerator and struggling with it from day to day. My hope is that no one will buy a Whirlpool ever again. I certainly wont.Updated on 12/05/2017: Whirlpool, faced with my wrath over a refrigerator set on LOW that froze $1800 worth of insulin, provided a replacement (25 Cu Ft side-by-side refrigerator). I have owned two previous Whirlpool refrigerators -- for 20 years each -- as well as other Whirlpool major appliances. I WILL NEVER BUY ANOTHER WHIRLPOOL APPLIANCE. The replacement is deficient in every design and functional aspect I can think of. Temperature is uneven in both freezer and refrigerator. Food in the freezer is coated with snow within a week and dried out and spoiled within a month. Ice comes out with such force that it ricochets out of the glass and around the floor. Water from the dispenser is warm. Leafy vegetables spoil within 2 days. Whirlpool sent technicians who informed me that the unit was working properly because it was cold. PIECE OF JUNK! DONT BUY ANYTHING MADE BY WHIRLPOOL!

We bought a 20.5 cubic ft Whirlpool refrigerator. 2 months later it started cutting off, and on in a constant repeated cycle then run normal for a while. We had 2 Whirlpool repair appointments. The first guy said he couldnt come fix it unless it was acting up while he was here which was a intermittent issue. Refrigerators dont perform on cue. The 2nd guy came out after the first guy messed around long enough for the warranty to expire. We went ahead, and replaced the startup relay (most common problem). He replaced the control board, and wire harness. He said if that didnt fix it he didnt know what else to do. 2 hours after he left the fridge was right back to doing the same thing. He failed to report back to Whirlpool that the fridge couldnt be repaired. We contacted customer service, and their resolution was to get another repairman to come out, and replace the control board which had already been replaced. In the end they bailed on us, and left us stuck with a broke refrigerator, and we had to buy a new one ourselves. I might add it was not a Whirlpool. They spent $471 trying to fix a broken fridge, and wanted to send another repairman (another $100) to fix a $629 refrigerator how does that make any sense. It was a very disappointing experience, and Whirlpool should be ashamed.

Front load washer Whirlpool Model# WFW9400SW02, only had this machine for about five years and the main interface control board has gone bad. This part cost 1/2 as much as buying a new machine. My parents had the same washing machine for almost 30 years and no problems. Whats wrong with this picture?

This was the first new appliance that I had actually ever had and I purchased it in October of 2010. After four months, it started make a grinding sound. I called Whirlpool and the repair man replaced the motor. Approximately four months after that, the lid got stuck and the machine would not respond. Same routine as before, but this time the transmission was replaced. While the machine was apart, I noticed the white insulating panel from the bottom was brown in a spot and looked as if it had gotten hot. A month before the 1 year warranty expired, the washer started making an intermittent grinding sound nearly identical to the sound made when the motor went out. This time a different service company was sent out my Whirlpool and the said that nothing was wrong. Now, the machine is out of warranty and has stopped cleaning close and during the spin cycle the you can hear water running into the machine constantly. Last months water bill shows a 40% increase in water consumption when nothing has changed to incur a larger bill. Seeing all these comments makes me wonder why the heck nothing is being done to force recalls on such poor products. Consumers should be treated with a lot more respect than this. I will never recommend a Whirlpool product to anyone I meet. In fact, I will strongly discourage anyone who is contemplating buying a Whirlpool washer machine.

I bought a Whirlpool washer and drying matching set (model 6400sw3). I liked it because it was extra large without agitator in the middle. Ive had it for about 2-3 years and I have already replaced the drain pump, motor and barrens, it has cost me over 500.00. I thought now OK its working fine, but now its giving me a code every time I wash of LD. I am so fed up with this!! I should have bought a new washer but I felt as much as I put into it, I basically built a new one. And now this code comes up every time and I have to power it off. Im not sure if anyone else has had this problem but I just dont know what else could go wrong with this. I will never ever buy a piece of junk like this again!!

My 4- to 5-year-old Whirlpool Cabrio 6300 began to display errors recently. F1 was the 1st error code I encountered. After giving the washer a hard shove and rocking, it began to work properly again... for a while. I noticed on some large loads that I was getting an LD Long Drain error. I could hear the pump running but with little water flow. Eventually, it would time out and give the LD error. A service tech was called and determined that the water pump was defective, although the impellers inside appeared okay and had no foreign objects to impede its spinning. After spending $225 for the service call, the LD error resurfaced about an hour after the tech left. Tonight I got the F1 error again, and once again the washer responded to a sharp rap. The replacement control board, which the F1 error code involves, is $220 plus labor. $440+ for a repair to a $600-$700 washer? Im going to dissect the main control board tomorrow and look for loose or corroded connections. I cant understand why the LD code occurs when I can hear the drain pump running... just very little comes out. Other times it empties like Niagara falls... I cant understand why it works sometimes and fails others. The pump is either on or off. It doesnt have multiple speeds as far as I know. Im not sure what to do next... probably try to re-sell the new pump that was installed to recoup some of the money I paid for a non-working Cabrio. This seems to be a very common occurrence.. Have any class action suits been mentioned? If so, please feel free to contact me.

We bought a Whirlpool Cabrio washing machine a year and a half ago. It started making loud noises over time and finally stopped. Whirlpool did advise us that it was out of warranty but suggested they send a factory repairperson out. They told us depending on the problem they might pay the bill. It turned out that a nut holding the pulley had not been tightened up properly at the factory and had no restraining device, so it simply rattled off over time. Since we dont use the machine that much, the problem went past the 1-year warranty. It cost us two hundred and fourteen dollars for repairs. I could have put the nut back on myself for free. The service guy also said they had multiple similar problems and I should contact Whirlpool and they would probably work with me. No chance. They only kept repeating that it was out of warranty. I even talked with a supervisor who said the same thing. I asked to appeal further and she refused to give me anyone else I could contact. I asked for their legal department information, and she said she did not have that and I would have to get that through my attorney. What a joke. No more Whirlpool for me.

Whirlpool Cabrio TLWasher purchased 2011. Doesnt drain, no spin, inconsistent cycling, poor washing action....wont even attempt to repair, in light of reading product reviews and consumer experiences with this washing machine- $600 junk.

I bought a refrigerator from Lowe’s and the refrigerator had a lot of manufacturing defects. I called Whirlpool and 3 techs were sent to my house. After the last tech, Whirlpool decided to exchange the refrigerator. Since then, Whirlpool has been playing games with me.

Takes 2 or 3 full cycles to dry small load. Big disappointment, drying is such a horrible experience since the clothes never dry when I expect them to. Not satisfied at all.

Had them come out numerous times and last guy changed out entire motherboard to no avail. Freezer side freezes and then thaws. Now it is just a two sided refrigerator. Before Thanksgiving I was promised new refrigerator and none arrive after phone calls. No refrigerator for thanksgiving. None for Christmas. Finally today at 7:00 this evening January 17 2020 it arrives. I am suppose to be in bed. I have two terminal illnesses. I moved out boxes of stuff out of refrigerator. Installer came in and said I had to move stuff on the porch that they are not allowed to. I get all done, finally sit down and he comes in and says there’s a big ding in bottom of refrigerator. No idea when another refrigerator would come. Who is going to put all my furniture back? Who is going to put my food back in my refrigerator. I bought the entire Whirlpool package Made In America. I should have went cheaper and bought from China. Now there’s trouble with dishwasher and they have been out once already for that. I could worry about taking care of my health if I didn’t spend all my time dealing with whirlpool. Maybe they can bury me in the refrigerator and my daughter won’t have to buy a coffin. I make 1000 a month on disability and get 16 dollars in food stamps. I have thrown 1000s of dollars away after motherboard was fixed. I went and my friend helped and bought new groceries. One day took out a frozen burrito and as I was putting it in microwave I noticed it had mold all over it. Another food dump. Whirlpool pool answering phone says whirlpool cares. Well they don’t care about me.

All of these awful reviews and you continue to sell the Made in China JUNK!!! And shame on the stores that advertise and sell Whirlpool JUNK!! They should put a warning on these machines stating Will not last, gets off balance and does not clean your clothes. Yes we bought the Cabrio like the others, our clothes would not get clean, because like sheets, would end up looking like a doughnut without a hole and all of the dirty water would drain through the middle and make a spot. Then you have to wash them over and over. But that is not the worse part! It only lasted 13 months, YES I said 13 months just past the warranty LOL!!When the man came to make repairs, it was the gear box and was going to cost almost $600. Almost as much as we paid for the machine. He recommended getting a Speed Queen, we did and I LOVE it!! I think it is the BEST MACHINE I have ever had. They are a little hard to find though, but I found where they were sold on the internet and the dealer had to order it. Well worth the time and trouble, (trouble) which I dont expect to have with this machine. Like I said it is a wonderful beast. And I will never buy another product made by Whirlpool. Before my husband retired he made prototypes for autos so he knows about testing and Whirlpool had to know this product had bad flaws before they put it on the market, I call that fraud. Bad taste in my wallet, Michigan.

Bought in 2009 brand new set washer and dryer together at Best Buy. The washing machine in 2011 started its never ending problems. I’ve paid for parts & labor for the door lock sensor mechanism multiple times where I learned to repair that myself even buying parts and installing on my own last time... Then a drain pump went bad. Replaced that. Now a code f51 sensor to a motor rotor not spinning issue. Horrible. All the money and time in this unreliable machine is so awful. This thing also isn’t that great when it works too. Goes unlevel way too much having to redistribute and restart cycles all the time... Wish it washed better for the price and all the trouble. It is the worst machine. Has to be! Everyone I know can’t believe the fight I’ve had through the years with this machine. The company doesnt help you. Costly headache Junk machine!

I purchased the 19 cu. ft. Whirlpool Estar refrigerator WRT 3595FYW on 4/28/12. Freezer began showing frost immediately. Repairman from Marcellas Appliance where purchased - (518) 381-1957, came to check it, put a sealer around the door openings of refrigerator and freezer. Frost continued. I called Whirlpool. They sent another repairman from EB Russell in Schenectady, NY, door needs replacing. Door was ordered and when received by them, the door was replaced on my refrigerator.In August 2012, frost is in freezer, on its roof, on the door daily. I called Whirlpool. I told them I wanted to remove it from my home. Whirlpools reply was, you have a repair warranty, not a replacement warranty. I was not advised of this when I purchased. Otherwise, I would have gone to Sears, Lowes, etc. On 8/16/12, another repairman from The Appliance Man, Albany will be here Monday. Its dishonest sale, replacement was advised possible by Marcella, that it was just a matter of course to get an okay from Whirlpool. This is not so. There is no replacement or return policy. Please help. Thank you.

I am very disappointed in my Cabrio washer. I have had it for two year and now I have to spend $ 250.00 on a machine that sounds like Im in a machine factory. It is so loud in the spin cycle that you cant hear a TV or radio. Also the lit of the washer broke in the start of the second year. I had my previous washer for 15 years before requiring a service call. I have to agree with all the reviews that this washer should be recalled. Maybe if we all call the media in on this problem Whirlpool will be forced to pay for a recall or repairs. Another case of big business ripping off the consumer.

Was very excited to have purchased Whirlpool stove with convection oven. The paperwork from Home Depot showed SELF CLEANING. Due to not feeling well from cancer I didnt realize it was AQUALIFT! A few years passed but I never used oven. Pandemic changed that. When I tried Aqualift. Did it 3 times in a row but nothing was clean. Called Whirlpool & they offered to send me a paste I could rub in & rinse off. THATS NOT SELF CLEANING. ITS MYSELF CLEANING plus cancer in abdomen so difficult for me to do. Class action suit is being filed again but not sure if it will be for 1 state. Many complaints on Whirlpool & other companies using aqualift.

We originally became alarmed by an awful smell and noticed that our Whirlpool Conquest side-by-side refrigerator freezer/fridge was not keeping food items cold. Upon further inspection, we saw that the compressor starter in had started fire and melted. Our refrigerator model #GS6SHAXLS42 and serial #SM3832794.

We bought a Cabrio washer four years ago for over 1,000 dollars. It lasted two years. The cost to repair was too high. We bought a low-end simple machine two years ago from Whirlpool. Now we are told it needs a new control panel, which again is going to make it not worth fixing. Two machines in four years. I called their customer service and there was nothing they could for me. The person they recommended to fix it told me it wasnt worth fixing and didnt even come out. I am done with Whirlpool.

Just like so many on this site Bought Whirlpool Model #WRF990SLAM02 refrigerator new in 7/2013. Just went on vacation for 2 weeks, I come back and the freezer and ice maker are not working. If what everyone on here are saying is true then it looks like I too will have to purchase a new refrigerator and you can bet it wont be a Whirlpool.

About 29 Nov 2011, I bought a Whirlpool microwave, which model no. is magic cook 206 (mech). Sr No. CNF103400315, when we bought this item, we asked for the start up kit, but at that time they said that in grill microwave we dont provide start up kit but after a month when I again raise for start up kit, that time they give but in start up kit some item is missing and the sealed is open. So I kindly request you to take some action to the shop.

Purchased a double wall oven and had it for 13 months. Used it this past Christmas and for the first time used the self cleaning mode. After an hour the power went out and now the oven is dead. Whirlpool service sent me to a local repair company and they want $70 to come out and look at the oven. This seems like a huge problem based on all of the feedback on the web. This is an obvious lemon and Im going to talk all over social media about the poor quality of this product.

Whirlpool Water Heater bought May 2011: Water heater not heating. I called Whirlpool and they stated the equipment is under warranty but not the labor; $137.50 for 1st hour of service. Troubleshooting is a joke. It just doesnt heat. Waiting on the 3 plumbers to call me back. They are busy. Water heater went out Sat morning and Whirlpool doesnt open until Monday. Its Monday at 5pm and Im still waiting on a call back.

Bought the top of the line Whirlpool Cabrio washer and dryer. Washing machine lasted 3 years. Took forever to do a load and would not be clean after taking an hour to wash. The dryer is still going, but would not surprise me if it died any day. Do not buy.

I purchased my Cabrio washer and dryer 4 years ago, my dryer doesnt dry completely, I have to do 2 to 3 cycles to dry. My washer has an f51 code and I have problems unlocking the lid and it takes 2 to 3 hours to wash. This is ridiculous and it causing my electric bill to spike. Is there a recall on the Cabrio?

Purchased the Whirlpool DU915 in 2004. Its been 16 years and I havent made a single repair. A lot of that is just proper use, i.e. scraping off food stuff, using correct soap, etc. I have other newer Whirlpool dishwashers at rental properties which have required repair due to misuse. I would recommend Whirlpool products to friends and family.

Gas control not working. I have replaced the thermostat twice in three years. Now, the hot water tank pilot will not light. The igniter works; a new thermostat has been properly installed, and the pilot will not light. The gas is on, and the tank has functioned. I just want a new gas control.

I bought a dishwasher with a 5 year warranty. It broke just after one year of purchase and they are giving me the runaround with replacing after finding that the part the part needed to repair machine is no longer available. The warranty clearly states that they will repair or replace with same or comparable machine and they are refusing to do so. I am at my wits end and I have no one to turn to within Whirlpool as they say it is their decision how they want to handle warranty.

I purchased this refrigerator, approximately 3 yrs. ago. Right away the top crisper broke. I have put up with this broken crisper only to have broken the PLASTIC lips that hold the crisper to the top shelf. Piece of junk. I looked to order a new crisper but way to expensive so I just suffered thru. I cant even use it anymore as I cannot open or close it without it falling onto the bottom crisper. Would like to throw the thing out, but cannot afford another one. IT WILL NOT BE A WHIRLPOOL!!!

I got my water heater 3/13/12. Ive had to restart it now 4 times & have been totally out of hot water for two months! How can I get help from you or Lowes? This thing is supposed to work for 6 years & I havent been able to keep it going for 6 months! Help please! Can I get a different one? This one hates me! Being widowed & having a metal hip, it’s hard to get safely into the attic to restart it and not sure it will work longer than 2 or 3 weeks! Ive been bathing in the kitchen because thats where the stove is! Thats the only way I have of having hot water, is on the stove! Thanks for listening!

Late on the evening of Monday, January 27, 2014, after springing a leak in my 8-year-old water heater, I purchased a new Whirlpool model N50T61 replacement from Lowes. Installation went smoothly and the unit lit off fine the first time. It heated the initial tank of water rather quickly, but the next morning, I noticed the status light on the control unit was not blinking, which indicated the pilot light had gone out. I relit the pilot light, the water heater fired off and appeared to be working properly. 12 hours later, the status light was out again. I relit the pilot, but within 20 minutes, it went out again.On Wednesday, the 29th, I called Whirlpool customer service and explained to the representative what had been happening. He stated that since the status light was not blinking a code, the problem was either an air supply or venting problem, and he couldnt help me. I relit the water heater again and performed the match smoke test described in the owners manual on the vent connection. It did exactly what the manual said it should do, so I assumed that was not the problem. However, while performing this test, the water heater went out again. This time, being right there when it shut off, I saw the status light blink twice about 5 or 6 times before it quit blinking all together. The two blink error code indicated low millivolt signal from thermopile.I called customer service again and explained to the representative what the first person had told me and also told him the results of my test and that this time, I had observed the two blink error code. He asked if I had a multimeter (which I do), so he had me disconnect the wires for the thermopile, connect the meter to the wires, light the pilot and read the voltage. My meter is an old analog unit, and not capable of reading millivolts (which is what the thermopile output is), and I informed the rep of this, but he had me do it anyway. As I suspected, I saw absolutely no reading on the meter. The service rep stated that he believed the error code and decided to send me a new thermopile assembly. However, their shipping department was closed for the day and I should not expect to see the new part until Friday. This was unacceptable, but he stated that this was the only option available to me.After thinking about this situation for a while, I again called Whirlpool customer service and told the representative that I was not satisfied with the solution previously presented to me and that I wanted a return authorization to take the water heater back to Lowes for replacement. The rep stated he couldnt do that, but said that there were a couple other things I could try. He attempted to explain these procedures to me, but wasnt able to do so clearly. He stated he would email the instructions to me. As of this writing, I still have not received the instructions.In the meantime, I did some internet research and found that Whirlpool water heaters have numerous chronic problems, including the issues I was experiencing. I decided this was not a product I cared to own. I called the Lowes store where I purchased the water heater and spoke with the manager. I explained the entire sequence of events to him, and he told me to bring the water heater back for a full refund. Since my local Lowes store only sells the Whirlpool brand, I took the money and purchased a different brand of water heater from another home improvement store. Needless to say, it will be a cold day in hell before I ever purchase another Whirlpool product.

I purchased a Whirlpool 50 gallon gas hot water heater 3 years ago. I have 3 daughters all in school age. When my old one finally quit due to tank failure and out of warranty, I went to Lowes and bought a 6 year warranty hot water heater costing around $600. Now I figured you get what you pay for RIGHT! WRONG! So about 2 years ago the pilot light started to just go out on occasion, a bit of an inconvenience but there was no default code warning me of any other issues. So typically we just relight it. I called Whirlpool to get help with this issue, but they wanted me to pay for a technician to diagnose the problem. Um isnt that what the warranty is for? I said dont bother. Im not paying $150 for someone to tell me what I already know. Ill just keep relighting it myself. So finally the pilot light goes out for the 100th time but this time I go to reignite it and BOOM! It sounded like a twelve gauge shot gun going off in my face! Then it flutters flames into the chimney of the hot water heater. Scared the crap out of me at first. But it finally stopped and run fine. Well Im laying in bed a few nights later and woke up to a loud thumping noise, I go down stairs and it stops. The following day Im in the kitchen and THUMP THUMP THUMP BURP BURP BURP. Run over to the hot water heater closet and theres the flames shooting out of the gas valve into the hot water heater then BOOM! Its out! The valve unit finally took a crap I guess. I call Whirlpool again to get my warranty - this time it definitely needs to be replaced. So the guy tells me the parts are covered in the warranty but a technician needs to look at it first and the technician Ill have to pay.. Excuse me but what the ** did you just say? I have to pay for a technician to look at your failing part? No I dont think so! Just send me the part - Ill replace it myself. Im a millwright electrician by trade. I specialize in power plants and refineries. Im sure this little gas valve wont be a problem. I spoke with these idiots on a Friday and he said I could have it ground shipped for free and it should be here in 5-6 days or pay extra for quicker delivery. What the hell did he just say? I could pay extra for quicker delivery on Whirlpools faulty part? ** whirlpool should be saying Well have the part overnight to you.Now since it was a 3 day weekend theres no sense in me paying $40 to have it delivered 3 day because it still wouldnt arrive until close to the five day. So I just looked to see where my damn part is because it shouldve been here by now according to the guy on the phone. NOPE! Its set to be delivered in 5 more ** days. DONT BUY A WHIRLPOOL PRODUCT. THEY DO NOT PRACTICE ETHICS.

Initially felt the burners and oven took a LONG time to heat up, but just accepted it. After a year and a half, the motherboard died. The part alone was almost $400 and labor $100. The self clean does not work very well. Glass top is very hard to clean. It has a large oven space and looks nice, but would avoid Whirlpool at all costs following this experience.

I have the same pilot light problems as everybody else. I pulled the burner unit out, and cleaned, and blew everything out, and took a wire brush to the openings on the floor of the unit. I called customer service, and was asked about ventilation. I didnt mention that the heater still didnt work, even when the door to the tin water heater was removed, so venting is not the likely culprit. She authorized a repair that will likely do nothing from the comments I see.The real problem with their customer service, is the apparent stupidity of the computer system. She asked me for the model and ID number. I had to cut through the extra insulation blanked on the tank to get it. However, when I gave it to her, she then asked me if I was ** and if I live at **. If this information was already in the computer, why couldnt there be a search by my name and address, to get the model and serial number. Obviously, I had registered the water heater in the past. Isnt being able to get this information the reason to register in the first place?Now, I have to replace the extra insulation, all because of a stupid inability to create the necessary searches in their customer database. Yes, I could have written the numbers down, but why have the customer registration at all, if it isnt to be used for anything, other than data mining of the customer base.

Stove was purchased in June, 2021. Two months later, oven will not heat up!!! Contacts Whirlpool, and TEN days later, a service person finally shows up. Problem appears to be a circuit board that they dont have, and has to be ordered! When will it arrive? He has no idea!!! I called Whirlpool, but its frustrating and a waste of time. You only get to talk to someone that appears to be reading from a script! If were lucky, well be without an oven for one month; however, it could be two...or three...or four!!! My advice: Dont buy this stove/range!!! Not only is the oven an issue, but it just seems flimsy and subpar quality, especially the oven door. Added to that, the glass top is very difficult to keep clean... Worse than any glass top stove weve had in the past.

Whirlpool Washing Machine Model WTW4950XW0 - This washing machine was purchased as a gift by my father. We have owned this machine for about 2 years. I am very disappointed with the quality of this machine. I have 3 children and several pets. I use my machine a lot and need a quality item that will last. This machine is not that item. Within a few months, the machine was off balance and bolts had to be tightened. We have had problems with the belt, bolts coming loose and the machine not draining.More recently, the machine has become very loud... For approximately the last 6 months. My husband has taken the machine apart and looked for anything to be wrong with it and has found nothing. Now the machine is not running. I will turn it on and it fills with water and then stops. I will clear it out and restart it and it does the same thing. Another issue has been with spinning and draining. The clothes are soaking wet even after the drain/spin cycle.I have researched what could possibly be wrong with this machine and have found a vast number of items that could need replaced. With the money I have already put into fixing this machine in the past and the amount it will cost to fix it this time, I believe I will be further ahead if I buy a new machine made by a different company. I will not be buying a Whirlpool product again.

I bought Whirlpool Cabrio washer two months ago (Model number : WTW7300DW0). They indicate washer use less water and clean better, but that is not true. Some clothes on top of the load were not even getting wet and clothes smell bad after washing. Even worse is that clothes got holes in many places and some clothes were totally destroyed after washing. In just two months, I have to throw away many of my towels and clothes. I dont believe this kind of washer should be sold again. This should be a recall to give us a replacement ASAP and remove any products still in the market. There are many complaints online, I hope someone will stop this and do the right thing.

I hadnt had the machine. In no time, I started noticing brown rust looking spots on my whites and light colored clothing. I got to looking and had rusted out all around the bleach dispenser, entire area on the entire top. I was told to replace it. This would be about $200. Ridiculous!

In March of 2013, I purchased a Whirlpool refrigerator; model number WRF990SLAM00 from Lowes. About two weeks after my manufacturers warranty expired, I called Whirlpool because the refrigerator wasnt working anymore. It took several weeks and the need to call four different repair companies before we finally had one that was willing and able to come attempt to repair the refrigerator. They came out, changed a few parts and left. Several weeks later, the refrigerator quit again. This time, when I called whirlpool (about June 2014), I was able to convince them to give me an extended warranty. They told me that the warranty would expire in December, and that all the work and service would be covered up to that date. This was fortunate because that repair, parts alone, was near a thousand dollars. Of course, the repair company couldnt make these repairs in my kitchen, so they had to remove the refrigerator and take it to their shop for several days. By this point, we had lost two refrigerators full of food. In mid-November 2014, the refrigerator quit again. We lost another refrigerator full of food. We called Whirlpool and the repair company again, and the repair was scheduled. I have six children and we spent Thanksgiving without a refrigerator in our home. The repair shop kept the refrigerator for several days after they fixed it to make sure it wouldnt leak coolant, because by this time, they had figured out that there were several pin hole sized leaks in the coolant line. It didnt leak. They had it for about four weeks total before they brought it back to us. By the next morning after having the refrigerator plugged in for several hours in our kitchen, the temp was at 65 degrees in the refrigerator and 60 in the freezer. I called the repair company again and whirlpool. The repair company has come to the conclusion that there must be a leak in the coolant line in the walls of the refrigerator and it is deemed unrepairable. They called the whirlpool tech line and the tech people told them to come back to our house and read the pressures the next day. They came out, read the pressures, determined that coolant had leaked out and told the tech department it was not repairable. The tech department told them to go through the entire cooling system again. This is something they have done several times. Today, they brought the refrigerator back after going through the entire cooling system, yet again. Its still not working. As I type this, my refrigerator is at a balmy 55 degrees. The repair company and I have both, on numerous occasions requested a replacement refrigerator. This was a very high end purchase for us. The original cost of the refrigerator was around $3,000. I have lost around $1500 worth of food, which Ive also requested on numerous occasions for Whirlpool to reimburse and they refuse. Whirlpool refuses to replace the refrigerator. Today, I found out that, by mistake, they gave me a one year extended warranty instead of six months. They said that it does not expire until June 19, 2015. Even with this information, they told me that the best offer that they will give me is IF I am willing to EXCHANGE my lemon that is in my kitchen right now, they will SELL me a replacement refrigerator at a discount. They say that the terms of the extended warranty are different than terms of a manufacturers warranty.This is unacceptable. I am currently out several thousand dollars for an over sized filtered water dispenser in my kitchen. Throughout 2014, we spent somewhere between three and four months without a working refrigerator in our home. As of right now, I havent had a working refrigerator for about six weeks and through Thanksgiving, Christmas, and New Years. I bought the refrigerator because I thought it would act like a refrigerator and not a paper weight. An Implied Warranty of Merchantability has no expiration date. It requires that the goods be fit for the ordinary purposes for which they are to be used. This refrigerator is not fit to be used.Id also like to mention that during the times that Ive spoken with Whirlpool on the phone, they have told me that they would replace the refrigerator if the repair company deemed it unrepairable. Typically when I call whirlpool, I am on hold for fifteen to thirty minutes before I get to a representative. Today, I was on hold for forty minutes before my call was disconnected. This has happened numerous times. Ive also had representatives disconnect the call several times when they were transferring me to another department, or putting me on hold. I estimate that I have spent at least forty hours on the phone with the customer service department for whirlpool in the last several months. And even, with all that, I have not had a dependable refrigerator for eight months. I need this resolved and I dont feel that it is fair for me to be financially punished because of the lemon that Ive already purchased from Whirlpool.

I purchased this washer over 8 years ago and we have been using it 3 to 4 times a week/ 52 weeks a year since. It has performed flawlessly up until about a year ago when it kept given me uL error. Everytime I wash the basket always spins wobbly and unbalanced it seems. I checked the Internet and it turns out others have had the same problem. The solution was to replaced the 4 springs supporting basket and that fixed the problem. Been working ever since.

I should have read reviews prior to purchasing the Washer and Dryer. The washer sucks big time. Does not clean clothes. Leaves soap in clothes. The repair man said use 2 tbsps. of soap. Still soap in clothes. I use 1 tablespoon of HE soap. 2 1/2 hours for 1 load because I have to use deep water and extra rinse on first wash. Then I wash again with no soap. I HATE this washer. Whites are now yellow after washing. Cannot do lightweight comforters. I am at the laundry mat more than using my new washing machine. Dryer is ok but does not remove any lint from clothes or towels. I always trusted Whirlpool. Not anymore.

I purchased a Whirlpool cook ceramic cook top for our new kitchen. The very first time I made something (it was lentil soup) something stuck to the cook top. I have had a ceramic cook top before for 18 years - never had a problem until the whirlpool cook top. I cannot get it clean. I have tried everything! Such as stove top cleaner designed for whirlpool cook tops ($22), other cook top cleaners, the single edged razor, a scrubby sponge, steel wool, I even resorted to furniture stripper - NOTHING has removed this spot. I am ready to throw out this new stove top! What a huge disappointment this Whirlpool product is.

Dont buy their produce!!! My refrigerators bought in January 2017 and just use 9 months. It breaks and repairs 3 months. It cannot repair and Whirlpool will refund for me, but I wait long time and no any answer. I try to call Whirlpool customer service. Their staff hold me long time and tell me they will be call back... Oh my God!!! I left my refrigerators 3 months ago. Whirlpool did not care the customer. Terrible company!!!

Bought an HE top loading washer 4/19/19. Oil leaking on floor from washer. Today, 2/12/20, while still under one year warranty, had transmission replaced. We have always purchased Whirlpool appliances. Not sure if we will in the future.

We had the Whirlpool Cabrio Washer [WWT5640xw0] for approximately six months and it began to behave strangely, very much like the other complaints I have read on this site. It works poorly, does not clean the clothes, there is a smell that is coming from the machine and it makes loud, inappropriate noises. It stops spinning and washing in the middle of a cycle. Before I become aware of the issue, I would find loads of clothes sitting in the water and the machine indicated the cycle was completed.What a piece of junk! We cannot afford to go out and get another washer at this time and based on what everyone else is saying, the cost of repairs is very costly. I too called the company and was greeted with indifference. I too will not purchase another Whirlpool product and have spread the news to my friends about this worthless product and manufacturer! My message to this company: Whirlpool, the right thing to do is recall the machine and provide us with a voucher so we might go and purchase another machine from any manufacturer we wish. But we all know that will not happen as the company is clearly saying to its customer base, Our sales and profits are more important to us than you and your satisfaction!

This washer was purchased on 12/21/2007. It was in a vacation home that was rarely occupied, therefore washer not used much. On 7/23/2008 the cycle switch was replaced. On 7/20/09 the same problem occurred. The washer may have been used 5 times during the year. The handle and rim also needed to be replaced. On 8/31/09 the switch and handle were replaced again. On 2/5/13 the door latch was BROKEN AGAIN. Now on 7/10/15 the door latch, start switch and cycle switch are broken again... DO not buy WHIRLPOOL products.

I purchased a Whirlpool Gold French door with the bottom freezer in October 2013. I had one repair done while it was still under the 1 year warranty, but by the time it was 18 months old, it began leaking refrigerant. I was told by the technician that the cost to repair it would be more than the value of the refrigerator, and the chances of the repair lasting more than 6 months were minimal. I had to buy a brand new refrigerator (not a whirlpool this time). I contacted Whirlpool customer service but they were non-sympathetic. Do Not Buy Whirlpool Products - Poor quality and high prices.

On 1/24/12, I replaced a 15 year old water heater that had started to leak after years of faithful service. The new Whirlpool unit heated water to a tepid level only, and that was obtainable only after running several faucets at a time, full bore. I used the product manual to trouble-shoot and was unable to find the problem, so I called Whirlpool customer service and was told that I would need to have a plumber come and and inspect the plumbing before a technician could be sent to check the water heater. I was not very happy about that, but complied. The next day, a plumber inspected the lines and fittings, tested the pressure and agreed that the problem was likely a faulty water heater. That cost me $95.00. I called Whirlpool again. This time, I was told that I should have had the plumber call Whirlpool while he was still at my home! The customer service representative agreed to authorize a service call, and I was given the phone numbers of three companies to choose from. Apparently, I chose wrong. The plumber seemed experienced and was very friendly. He was at our home for about 40 minutes, made a cursory inspection and said the problem did indeed seem to be with the unit, and he would return to his office to contact Whirlpool and arrange for a replacement unit and he would call back. Tellingly, I realize in retrospect, he did not give me a receipt. After several hours, I called the company and was told Whirlpool had not yet called them, and if I did not hear from them soon, I should call Whirlpool myself. This seemed reasonable to me, and I did so, at which point I realized I had been lied to from the start. The Whirlpool representative said that the service technician stated that he had run an isolation test, obtained hot water from the water heater, advised the homeowner (me) that the problem was in the plumbing, and I possibly had crossed lines. She also told me that the technician had said that he had difficulty making the homeowner understand what he was trying to explain. A complete and utter falsehood. I asked her how an isolation test was carried out, and that I would call the plumber to see what was going on, as this was not what we had been told. I was livid and called the plumbing company back just in case there was some honest mistake. Of course, there wasnt. I would like Whirlpool to be made aware that the company that they contract with is disreputable and has a history of deceitful practices. I found many negative reviews, and in fact the sort of treatment I received seems to be their modus operandi, no receipt, never a call back, assure the customer their problem will be covered under warranty, misrepresent the the service performed. The reason I add this last statement is that at no time was the new water heater disconnected, drained, refilled and allowed to return to operating temperature; the so-called isolation test a process which Whirlpool told me takes about two hours. This test did not take place. I previously stated that the technician was only at our home for forty minutes. There was no test of water temperature. I have since replaced my water heater with another brand--it works fine and there were no plumbing problems! I thought the name Whirlpool meant something. I have owned quite a few Whirlpool appliances over the years, in fact my new washing machine is Whirlpool. But I am definitely disinclined to purchase this brand again. I am so disappointed with the service I received from Whirlpool, a huge waste of time and money, and I am out $95.00 for nothing. I think Whirlpool should reimburse me for this, as the original (honest) plumber was correct. My water heater was defective and should have been replaced at that time. If it had been, you would probably still have a customer.

We bought a Whirlpool dishwasher and microwave from a reputable appliance store. The dishwasher top basket broke within 30 days. The microwave lost 100% power within 30 days. Both under warranty but parts had to be ordered. Couldnt use either appliance for over a month. What is going on Whirlpool? We need a refrigerator, but I no longer trust your brand. I dont want it to quit and then lose all of our food! Please get it together and make quality products again.

Im 61 so I have some experience. I personally know fridges that have lasted over 20 years. I just Googled it and found out the norm is 14 to 17 years. This hunk of crap lasted 4 years. As soon as I got it home and plugged it in (4 yrs ago) the most noticeable thing was the noise. It sounded like a tractor! I considered taking it back (wish I did). Then after a couple of years the pull handle came off! The whole time we had to be careful the door was closing properly. It was problematic. Ive owned (and re-sold) about a dozen fridges in my life. This the first one to fail on me. It was bad from day one!

We bought a dishwasher, stove and refrigerator last month. Dishwasher and stove work great, however the refrigerator is junk! The freezer part works great, but the refrigerator doesnt cool at all. The first time he was here the repair man said the seal on the door was bad and he glued it. He told us to not open the door for 48 hours then everything would be fine. IT WASNT. A week and a half later he came back. He looked inside, scratched his head and told us, “This model should have the “deluxe” fan and I dont think it does!” Said he would be back in 6 days with the fan and well “see if that fixes it”.I called Whirlpool service waited on hold for an hour before getting cut off. Called back waited 35 more minutes but actually got to speak to someone. The big solution... They offered me a 6 month extended warranty!!! Ive lost an entire refrigerator full of food. Missed two days of work and am going to miss another when he brings the “deluxe” fan. Also been eating out all month and probably spent $100 buying ice. IE... MOST EXPENSIVE REFRIGERATOR EVER!!!

We have a new home with a Whirlpool gold refrigerator that has been fixed twice in 3 years for not cooling adequately (over 45 degrees), a dishwasher that the mother board has gone out twice with 3 different service calls (repairman recommended trashing and buying a new one), microwave that is rusted out on inside door below glass, and washer with horrid smell if you dont wash with bleach weekly and dryer whose sensor doesnt sense anymore after 2 service calls!!! I cannot believe the poor customer service and lack of responsibility the company has taken on these not inexpensive products!! Like others on this post they will not acknowledge problems and tell me I should have bought extended warranty. I am so angry - there should be some sort of law that allows recourse for such bad behavior!

We purchased a WRF989SDAM03 model French door refrigerator in September. A month later it began to make grinding noises when running. The noises got louder until it sounded like a car idling. We called for service, and the technician diagnosed a failing compressor. They replaced the compressor with some difficulty. Three days later we lost cooling. They replaced the compressor again. Now the refrigerator cools, but it runs 100% of the time. I dont mean frequently, I mean it NEVER. SHUTS. OFF. Its never not running. Today a technician came out, and after 1.5 hrs of diagnostics on the phone with a Whirlpool engineer, theyve declared that it works. Whirlpool refuses to honor their warranty and says that because the unit cools, I should accept that it runs 100% of the time. I can get no resolution from Whirlpool.

RE: Our Whirlpool gas range/oven model# GW397LXUS05 installed Oct 2010 started acting up when setting the oven temperature. The 0 doesnt work so we input 355 instead of 350 etc... Other numbers have started to fail as well... Also it needs cleaning but a neighbor with the same model said whatever you do dont use the self clean for the oven, as they did & it literally burnt out the control panel costing them over $400!! Say what?? So we cant use the self-clean feature or well really fry the control board... Would LOVE to hear Whirlpools explanation on this one... And a minor issue but nonetheless worthy of a mention, the oven drawer never slides in/out properly & hasnt fit right from day one...