Whirlpool provides free replacement parts to repair this design problem but wont pay the service charges to repair their design problem. I purchased a KitchenAid french door style refrigerator (KBFS25EWMS10, SN K31902118) and it leaks water on the kitchen floor. At first I just mopped it up but later discovered they have a design problem in their drain system and water backs up into the freezer dept and eventually on to the floor. Customer Service provides free improved replacement parts for this design problem but wont pay the service charges to have the parts replaced. Simply put, Whirlpool/KitchenAid do not stand behind their product quality, instead they pass the problem and service charge cost for their design problem on to the consumer. Beware of this appliance supplier!

Their water heater is the worst ever! I will never buy another Whirlpool product. We purchased our water heater on January 17, 2010. We had to have the entire electronic system replaced in August 2011, including the lower element, control unit, thermisol, and electronic. Now, just a few short months later, the system is not working again, plus, the containment unit failed, flooding our basement. When we called Whirlpool, we were treated callously and rudely. Now, we have to pay to have the old unit removed, and a new one installed (they told us to throw it in our trunk and return it to Lowes, as if). Why did we pay to have this warranty when both the product, and the warranty are junk? Never, ever again! While Im at it, I should add that our range, and refrigerator are also made by Whirlpool, and those too, are pieces of junk. I guess were bucking up, and scheduling a new installation. If there are any further problems, I will be contacting an attorney.

I have always liked Whirlpool products but it seems lately they are lagging in this department. My washer/dryer combo each separate I dont feel are doing the job they should be. Washer is the bigger problem. Softner dispenser not distributing the softner correctly and now I have to clean out after each use. These are about 10 years old now. Is not spinning all the water out and not at all sure if clothes are getting clean. Most of their products usually lasted much longer back a few years.

I went from an HE front loader to an HE top loader (Whirlpool Cabrio WTW7000DW0) due to the risk of mildew with the front loader. Im not the only one doing laundry and if someone else does it, it always seems that they shut the door when empty, contributing to moisture and mold that needed to be cleaned out of the gaskets. I am so unhappy with my top loader HE washer. When I stop the machine and look, I always see my laundry half covered with dingy water, sometimes part of it still dry at the top and it is disgusting. I frequently have to rewash loads due to detergent getting trapped in folds or pockets created that hold on to dirt and lint, even being careful with the detergent amount. I run the washer now every time with settings of deep water, extra rinse, heavy load and presoak with instructions, with settings taped to the top for others.At almost 1 1/2 hours each load, we just cant keep up. The laundry still forms pockets and sheets form a giant tent over the entire load that has to be unraveled at the end of the cycle and wound so tight it had no chance of rinsing. I had to get a repair person out because it got out of balance and he had a small hand-held computer to enter a code to rebalance it. When we discussed the issues I was having, he was ready for everything I was doing wrong. He told me I can not wash blankets or large items (I thought I was buying large capacity with such an enormous drum). He told me they have caught people adding water with a bucket during cycles and that the washer software can tell them if people are trying to work around the system which voids the warranty.Apparently, this is a common complaint he blames on the government wanting high efficiency so they make the numbers look good, sacrificing the ability of the washer to perform at what a consumer expects. I have never seen the water in my drum higher than a couple inches and the drum is HUGE, but never used to capacity. He told me his wife demanded they get a commercial washer because she was so angry about how poorly it cleaned. I feel so scammed and I wish I could have my old agitator back. $100 for the repair call, $150 for the code to be put in and Im on warning that they will see if I try to add water, run out of balance or dont comply with any reason they can void the warranty by just checking the data the washer is collecting on us.

My refrigerator is now 5 years old. I have a stainless steel fridge. I didnt even have my fridge for 2 months and the one door started to rust. Whirlpool did fix that but now my fridge isnt staying cold. My extended warranty was just up 5 months ago. Figured some of the repairmen that we have called wont touch our fridge because they say the model that we have breaks a lot and that Whirlpool discontinued making this model. I am disgusted with this fridge.

Bought the hot water heater, installed it. It leaked from bottom. Whirlpool warranties it. Replace it with new heater. It too leaks. I Google problems with Whirlpool hot water heaters. Found over 1500 complaints.

I saw on the Today Show that my Whirlpool Duet washer, purchased in 2008 was a mold-producing nightmare. We are now part of a class action lawsuit that seeks redress. When I called Whirlpool Customer Service, I was fed the company line that the problem is that we dont clean the machine regularly. The instructions call for monthly maintenance, but the rep said we need to wipe it dry after each use. This is an original defect in the machine that Whirlpool refuses to own up to. We had been Whirlpool devotees for years but will never purchase another Whirlpool product.

In 2011, I bought in Croatia, for the start, 2 washers (model 3LCHW9100WQ) and 1 dryer (model 3LCED9100WQ) and opened the first self-service laundry in Pula, Croatia. Since the beginning, I had problems with the gum (black). After the washing cycles, you could see black lines on the laundry. Whirlpool Croatia denied that the gum can be the cause. After two months, they gave me new gums, but the problem still exists. After 5 months of work, the first malfunction on the washers started. The biggest problem is that it took and still takes them up to a month to repair them. And these problems I have ever since. Also, the error codes never showed the correct malfunction code. In global, if I take that I have these washers and dryer for about a year, they were out of function for more than 3 months. The warranty expired in April 2012. On these reasons, I cannot recommend any product of Whirlpool, and I have to change to another company to buy more washers and dryers.

I bought a whirlpool washer from Whirlpool on February 27, 2011. Since then, they have come out and repaired the washer for 5 times. They have even taken the whole motor out, and replaced it. The last time they came, they said I would have to pay for the next time. Now, it has broken again, and I have to pay for a washer repair that is less than a year old. We bought the Whirlpool washer at Sears, and neither Sears, nor Whirlpool will stick by their product. We cannot afford another new washer, and to pay for repairs is a stretch too. Is there anything you can do?

The Whirlpool range has worked effectively and efficiently for over ten years. We have experienced no problems. It is used several times a day to prepare meals and bake items. The cook top gas burners ignite easily, provide equal flame distribution, and the oven has an air blowing feature that makes cooking and baking much easier. One reason we chose Whirlpool was because this brands stellar performance history, its appearance, and its functionality. Overall, we could not have selected a better appliance for our use. We can unequivocally state that was and still is a solid performer for its cost.

Whirlpool Duet - they are highly rated and are aesthetically pleasing. Highly rated, they are expensive, my last Duet w/d didnt last as long as expected. Ive had to repair both machines once since I purchased them. Good quality is of utmost importance, plenty of washing and drying options, front loading washing machine, full size extra large capacity, attractive machines, good reputation for quality and lack of repairs.

It never seems to clean the dishes and it runs for 3 1/2 hrs. It is suppose to have all these Features but does a very bad cleaning job. I have used liquid soap, the cascade pods and the jet dry, still gives very poor results. Use to have a Kitchenaid that lasted almost 30 years - great appliance...

I purchased this Refrigerator Model #wrb322dmb, bottom freezer, 21cu ft. last year on July 3, 2015. In September I noticed rust spots on the top door. I called Home Depot where I purchased and they directed me to Whirlpool. I did purchase an extended warranty with Home Depot. Whirlpool did replace the top door. Thought that took care of it. Today one year and two weeks out of warranty, I again notice rust on both doors. Called Whirlpool. They said too bad out of warranty, not considering I had a previous report of this very same issue. So since I am very unsatisfied with this result and the fact that an expensive product is rusting, I decided to share to try to prevent someone getting stuck. Stainless steel is not supposed to rust which leads me to believe that it is not Stainless steel, but a Stainless Steel finish and not a very good one. So I am stuck with a rusting $1200.00 refrigerator only after one year. I have always purchased Whirlpool, but no more. They lost a 40-year customer. I have always bought American made but no wonder people are not buying American made any longer. TO SUM IT UP WHIRLPOOL STAINLESS STEEL APPLIANCES RUST! DO NOT BUY!

I had a Whirlpool oven for 14 years. It worked great and the control board burned up during the cleaning cycle. I purchased a new whirlpool oven that did not have an exposed bottom heating element. It takes way too long to preheat and if during baking, you need to change the temperature, it starts preheating again and the displayed temperature is lower than the original temperature that was set at the beginning; and it takes too long for the oven to reach the new temperature. This appears to be the result of the bottom heating element being hidden. Heating and maintaining a consistent temperature is far more important than being able to clean the bottom of the oven especially when this is a self-cleaning oven.Updated on October 20, 2015: This is an update on my last review. I was cooking a cake at 350 degrees and when the designated time was up, I opened the door to check for doneness. The cake needed to cook a little longer, so I closed the door and the temperature immediately went to 300 degrees and started preheating again which of course caused the oven to get too hot for the cake I was baking. Who is designing these ovens??? Certainly not a person that cooks on a day-to-day basis. I will never buy a Whirlpool oven again.

Purchased a Whirlpool Cabrio Washer a few years back... Started getting F1 error message and just proceeded thru it like most did initially, but now has become pain in the rear just to do one load of laundry as we get the error 2-3 times when we start each load - then on every load w/ 21 minutes left on the cycle. From the looks of things online this is a chronic problem and should be fixed by manufacturer. I called Whirlpool customer service and first person I talked with said they understand it is an issue but no longer are any recalls or reworks on that machine. I asked to speak w/ supervisor and sat on hold until I got one. Was then informed they do know it was a problem but was not something they could do anything about other than schedule a service company to come take a look. I specifically asked if there was at one time a recall or if they were fixing this issue for a while. She said Yes, they took care of some of their customers but are no longer doing that for this model. So basically because I didnt call in at the right time I need to fix my machine myself. I said it will be the last Whirlpool or Whirlpool associated appliance I ever purchase if this is the kind of customer service I can expect... The supervisor just said she was sorry to hear that and to have a nice day. Hopefully enough people read these reviews as I wish I would have before purchasing my Cabrio and dont buy Whirlpool.

Have had this washer for one year. Clothes have never been clean since day one. Dark clothes come out with white marks all over. Having to use an extra rinse cycle or set on bulky items - whats the point of a high efficiency appliance? Still not clean after that anyways. Stains such as chocolate and toothpaste still remain after washing and my husband complains of finding small holes in his clothes. Lid needs to be left open at all times or you get a funky smell. I am using the HE liquid detergent, even tried a cold water product for cold washes. I hate this washer. Wish I had my 20 year old Kenmore still.

After just 2 years, the electronic control board failed. The temperatures are stuck on the coldest/high mode for both the freezer and the refrigerator, spoiling some foods. The parts and repair are going to be $300. Whirlpool will not replace the defective part or pay for any repairs. Shame on Whirlpool! Model No. GB2FHDYWQ01.

Manufacturer refuses to acknowledge quality issues. This is not exclusive for the washer or dryer, IT IS BOTH! P.S. I owned & operated a Whirlpool Cabrio washer & dryer for 6+ years before up-sizing & loved them! I was grossly misled by the retailer to believe the new Cabrio washer & dryer were the same as the previous model of Cabrio. They are not. Their performance is subpar. Not what I would expect from top of the line. Washer does not spin out as dry as the previous model. It will not show error codes on display so I can deal with the issue at hand-it just shuts down. Dryer sensors do not work properly. It will not dry, or overdries to the point of shrinking clothing beyond use.This $2800 purchase is continuing to cost me money. I have never been more upset with a purchase than this. I have to babysit these machines. There is a bolt in the back wall of the dryer drum. Hence my destroyed brand new hand crocheted afghan. Oh and did I tell you that their licensed repair man told me that I should not be laundering bedding in my machines at home? Apparently there are no home use machines on the market that are able to wash bedding. Sheets. Pillowcases. All of it needs to go to a commercial laundromat. Ha! Makes a person question who we let in our home. If you would like a positive - its huge. But wont spin out a small load effectively.I have recommended and led to sale of dozens of the previous Cabrio model. I will no longer be standing behind this model or company after the poor customer service. Their answers are scripted. Its like speaking to a robot. No one is accountable anymore. I could understand if I did not know how HE machines worked or even the Cabrio model, but I loved my previous HE CABRIO FOR 6+ years!! Excuse me while I go vomit.

I purchased a new Whirlpool Cabrio yesterday. When I went to use my new washing machine it did not work. So basically I have a brand-new washing machine that is a lemon. I will highly recommend do not buy any Whirlpool products.

Bought refrigerator in Jan of 2019. Quit making ice in Oct of 2019. 3 service calls and felt like it was band aided until manufacturers warranty ran out. Now waiting on new freezer door to be made. 6 to 8 weeks out. We will see. Called Whirlpool and was offered nothing. No customer service whatsoever. Will never buy another whirlpool product again.

This Whirlpool washing machine is incredibly annoying and slow in everything it does. First off when you press the START button it takes 2-3 minutes before it decides to do anything, like maybe add water (except click, click and more click). If you have pressed the start button and you want to stop it to add something... again you have to wait almost 2-3 minutes before the lock is released and you can open the door. I am at 2 hrs and 15 minutes as I write this on the LIGHT WASH cycle with extra rinse and its still going. I have never seen anything like it. Cant imagine how long a HEAVY CYCLE takes. Cannot even try to measure the time. I put the load in and go to work and hope its complete when Im done 8 hrs later.We had a Maytag for 15 years with no issues (other than a drain hose cracked and had to be replaced) and it was time for a new one with a move to a new place. The sales associate convinced us this was the best machine at the time... Well what a mistake that was. There are no complaints about the actual washing. Everything comes out clean but I suppose taking that long I cant imagine why it wouldnt. I certainly cant recommend a Whirlpool washer to a friend, because I dread the thought of doing laundry at this point.

I bought an American US Craftmaster water heater in October 2006. I have paid a plumber 3 different times to work on this and the pilot light will not stay lite. I used the replacement parts they sent, followed their technicians directions over the phone, etc. Nothing seems to work. Christmas was not pleasant at my house this year. I’m still taking cold showers.

My 1 year old Whirlpool top loader is an absolute nightmare. It does not complete cycles. Stops all the time with various error codes. My washing comes out soaking wet. The pipes on the inside comes loose and floods the house. The machine stops all the time with all the washing clogged on one side of the drum. It is a 16 kg capacity machine but you cannot even think of putting 8 kg laundry in there. I will never, ever buy any Whirlpool product again. Cheap scrap! Thats what it is.

We bought a new refrigerator when we bought our house in Dec. 2008. On the third of July 2015 my Whirlpool Gold stopped being cold. In fact it was a bit warm. Had a repairman out here today. Warranty expired and the compressor has failed. Wow! Im not happy.

Another reviewer complained about a knocking sound upon startup. My Brand New fridge has been doing that and I have just ignored it. Maybe I shouldnt. Compared to our original Beaumark fridge, the Whirlpool is VERY NOISY.. Since the actual workings seem fine, I am not complaining but rather quite concerned.Especially after reading the numerous Negative Reviews.

I bought this Whirlpool Cabrio Washer 3 years ago. Yesterday will be my last repair. I installed a new tub (bearing failed have to buy a full tub to replace), new suspension rods and a new stator and rotor (cracked). Last year I replaced a drain pump twice, and a computer board. All of these repairs since I purchased this washer have cost me well over $900 for a $1400 machine. I dont mind replacing a pump every few years but these larger failures are unacceptable. We have moved back to Kenmore on some new appliances we purchased this year as result of trouble with Whirlpool. Whirlpool should send out a recall on the suspension rods; the existing ones seize at the top and stop functioning causing the tub to shake excessively. This led to the cracked motor (rotor cracked).

I purchased this microwave in September 2010. It was installed in a vacation home, so it has actually been used for less than one year. It has now stopped heating food for the fourth time. The previous problems miraculously fixed themselves after flipping the fuse for a few minutes. I guess I should have been suspicious at that point, but I figured maybe I had overheated something. But this time, the problem has not corrected itself. The Whirlpool representative that I spoke to, while very polite and personable, only scheduled a service call that will cost me $89.95 PLUS parts and labor. I asked her if other people had reported this same problem, since it had happened to me several times. She told me NO. I decided to do some research myself (yes, I know; I should have done this BEFORE I spent $578 on a worthless product) and found that many others have had the same problem, and that this is obviously a defect in the design of this unit. Unfortunately, I purchased the entire Whirlpool package because of a special rebate available at the time. Now, I am wondering if my other appliances will begin to break down in the near future. After reading about the experiences of others, I am calling to cancel the service visit. I will be removing the microwave from my kitchen and purchasing a new one. Whirlpool has lost a customer. I will NEVER purchase a Whirlpool product again.

I bought a Whirlpool range. After 15 months, I hadnt even paid it off yet the oven stopped working properly and then again after two years. These ranges are junk. Dont buy Whirlpool! They dont stand by the product either.

After just 22 months I need to shell out $300 for a new microprocessor. My Miele lasted for nine years. In the olden days washing machines could last for 15-20. Do not buy Whirlpool, from what I understand its a dying company...

Ive always had a Whirlpool washing machine and it has been extremely dependable. I have not had any problems with my Whirlpool washer. A Whirlpool has came a long ways with their pricing. It was very affordable for somebody like me and I cant afford a lot but I could afford this. I was very pleased with my purchase and with the product. They havent let me down so far.

The machine Will Not Clean the Clothes. Had to Buy A Maytag Washer.

We bought a Whirlpool range with glass cooktop and convection oven to replace a 20 year old stove which had served us reliably but was beginning to look a bit dated and worse for the wear. The new range was installed in February, less than 2 months ago. Today, while I was preparing Easter dinner and had a ham in the oven, the cooktop elements refused to heat, even though the cooktop on light was lit up. We followed all the troubleshooting tips we could find in the user manual and online, but nothing worked. We decided to do the rest of the meal in the microwave and just finish the ham in the oven (which had been working). Then the oven failed, and would not heat back up.As a last resort, we pulled the range out and unplugged it, to perform a hard reset of the electronics. (This was recommended in some of the online troubleshooting tips.) No joy. Both the oven and cooktop elements will not heat, even though the lights on the control panel light up. Now we have to call a service technician to come fix it in the middle of a pandemic. How can a brand new and expensive range be less reliable and less useful than the cheap 20 year old stove we just got rid of?

My Whirlpool microwave door started cracking little by little. Pieces started falling off. My warranty company stated it was cosmetics, so my warranty did not cover it. Finally, the whole door came off. The warranty company finally agreed to replace the door. Less then a month after replacing the door, part of the handle cracked off. There must be some sort of defect in the plastic used to make these doors, and if so, there should be a recall.

Whirlpool washers have been in family forever. RELIABLE. Extremely easy to use. Had for 10+ never had to have repairman. Large enough for queen size comforter and small enough for handful of rags. Spins like wow. Crazy dry.

The washer itself doesnt get the clothes clean. The clothes on top never get clean, they smell. It doesnt spin out the clothes evenly even though I put them in evenly. There is oil on my floor under the washer and Rent-A-Center doesnt care and its under their Benefits plus program. They were to send off both washer and dryer last time and had no paperwork where washer was sent off at all. It has ruined a lot of my clothes with spots and I used the Tide pods. Stopped using them cause they were not working. I will never buy another Whirlpool product or appliance. Water pump went out in one year... Why would you not care about your customers... I got this set in 2013 and its the Platinum line triple top loader. You lucky to do one load at a time, a single load that is...

Whirlpool Cabrio Washer - Owned this appliance for a couple of years and we are constantly receiving UL and F 51 codes on display. Washer stops spin mode after washer shakes violently.

August 10 2014, I purchase a new Whirlpool HE. Monday cant wait for the delivery of my new washer! Im ready with my HE detergent & 2 loads of dirty laundry. Tuesday, I want my broken old Kenmore washer back! My kids clothes came out dingy. Did a second rinse & spin but didnt help. Second batch had to be rewashed. Some areas were not even wet. Had to pause it to add more water to & again to rinse it. Plus I had to mix my softener into a cup of water to add it on rinse because I forgot the rinse ball, unlike the old washer where I add into dispenser & forget about it. So unhappy & dissatisfied.

I bought a Whirlpool Duet Frontload washing machine and now two and half years after buying it, it sounds like the tub is about to spin out of the machine. The repair man said it would cost over $750 to install a new tub and bearings in it. I thought the product would have lasted longer than two and a half years. I will never buy another Whirlpool product!

I love the brand. I just do not care for the lock lid on all the new washers. I could do without it. I do not have kids to worry about getting hurt. Im looking into finding a brand without a lock lid. I just replaced one before this one. For the lid breaking.

Very concerned. First the microwave broke. It seems that is burning on the inside. The model number is MH1150XMS-2, purchased in 2005. I have had to replace the plate. I have read of many recalls, because of the potential of fire. My model was not among the ones on the recall list.

I purchased a high-end Whirlpool dishwasher (WDT710PAYM) a few months ago thinking I was making a wise upgrade. Poor design and it wont dry dishes or properly wash utensils when theyre placed in the utensil rack on the door panel. The unit heavily condenses after using heat dry mode and large water droplets completely cover the top of the inside cabinet. Eventually, they all fall down into the dishes and you now have wet dishes again. The Whirlpool tech’s response was to scratch the cabinet plastic with a scratchy pad, smear rinse aid over the plastic cabinet and that should stop droplets from forming. Whirlpool’s customer service told me they shouldve never told me that and what I should do is be there during the drying cycle and open the cabinet door to let the steam out. This is completely ludicrous. Dont walk but run away from Whirlpool products.

I was excited to have an energy efficient washing machine and chose the Whirlpool Cabrio top loader. I truly wish I had read reviews rather than trust the salespersons advice. It does not clean clothes properly at all. They come out smelling dirty and are covered in white goo, even when the machine has just been cleaned. Stains never come out despite all of my efforts. Now I have water leaking out of the bottom as it fills. Not impressed at all. What a giant waste of money.

Whirlpool makes a beautiful product that does not last. I bought model WRX988SIBM in April 2015. Two years later the compressor is bad and no warranty coverage. Do not buy this model. It does not carry the Whirlpool 2-5 year sealed refrigeration warranty. Its amazing that an appliance that retails over $3K only comes with a 1 year sealed refrigeration warranty when Whirlpool offers it on other models. Be sure you know what your warranty coverage is before you buy any Whirlpool product.

The knob on the Gas Cook top stove from Whirlpool (Part no: W10594481) is very poorly designed. It is very flimsy and breaks easily inside. Outside it still looks intact, but if you examine it on the reverse side, where it actually fits into the cooktops metal rod to turn the gas up or down, we can see it breaks there, as it is made of very cheap plastic. Although it is supposed to be a Stainless steel knob, it is actually all plastic where it matters most. I bought the new cook top from Whirlpool in 2014 and within a year have replaced all the knobs as they were breaking once every couple of months. I am still having this problem after 2 years now. I have contacted Whirlpool and have asked for a solution to this problem. They dont have any, other than offering a new version of the knob which costs $10 more and it is not easily available anywhere. I feel very cheated that I got a poor quality product and no help from them on fixing the problem.

We purchased a Whirlpool stove a year and half ago. We were cooking and kept hearing (tick, tick, tick) noises. Couldnt figure out what it was. After removing the pot there was an area of 2x4 inches that had melted in. Not sure where the glass went. But it looked like a chip but on the surface.

Whirlpool Cabrio, H2 washer system type 588 01, serial # c0303 10 - We have been in our condo 5 years. The washer & dryer was here and new when we moved in. I have been displeased with it from the start. It takes forever to wash through a load, and the clothes are just as dirty after being washed as before. I soaked some whites in Clorox overnight and ran through using Tide and Downy. Then the stains and dirt were still there. I ran them again it was not any better. I had a professional from Hagadorn come. They could not find anything wrong. It cost us about $100.00. Others in our area have the same complaint. I have never been satisfied with this wash. It just does not get the clothes clean. Please help!!!

I purchased a 50-gallon Whirlpool natural gas water heater (12 year warranty) from Lowes approx 2.5 years ago. Just before Thanksgiving, the pilot light started going out once a day, then twice a day. Now, I can light the pilot light in Pilot mode but as soon as I release the red button, the flame goes out. I called Whirlpool and received phone troubleshooting support resulting in a recommendation to pick up a new thermocoupler from Lowes which I did. While searching for someone to install (unfortunately Im not that handy), I ran into the thousands of complaints filed about the very same problem Im having over a number of years and right up to todays date. I called Whirlpool back and got the same song and dance. Theyd be happy to help me troubleshoot if I can get the required meters etc. to test devices, do draft tests, etc. They claimed the problems were fixed with the newer model that I have but certainly cant explain why I have exactly the same issue. What they are not willing to do is stand behind their product and get me hot water. Tried calling Lowes and got the response that I have to deal with Whirlpool. It appears that this newer BFG model is just as flawed as the older model and the warranty is pretty much worthless other than getting a few parts. I used to think that Whirlpool products were reasonably good, however, I will never purchase another.

Whirlpool Gold French Door - I purchased this fridge in Aug. 2009 (model GX2FHDXVQ00 22cu. ft. French door with bottom freezer). Paid 1800.00. The fridge stopped working after 5 years, but the freezer works fine. A fridge should last at least 10 years. I wont buy another Whirlpool appliance! JUNK!

I purchased this Maytag clothes washer in 2007. So far Ive had to purchase and replace the front door 2 times. The current one now needs replacing. The plastic near the hinges disintegrates after about 2 years. This appears to be a manufacturing design defect. I have requested from Whirlpool to send me a replacement door for my washer. The part number is 34001178. The model number is MAH2400AWW. The Serial number is 14060452LE.I have spoke to four different levels of employees at Whirlpool after escalating the service request. Each time they have told me they are unable to send a replacement door to me, stating that the product is out of warranty. I realize that the washer is out of warranty but I believe this problem is a design flaw. The plastic near the top door hinge breaks down and cracks after 2 years of normal use. The last person I spoke with Michael (would not provide me with a last name) said to write to the Whirlpool corporate office with my complaint.

I purchased this machine three years ago. It is junk. I have had two washing machines and they lasted for years and years. Never had a problem with either machine. I purchased them from Sears. When I the Cabrio, I was told it was the top of the line washer for Whirlpool. Three weeks ago it started making a noise like a plane taking off. It wouldnt spin the clothes. The repair person said that it could be three different things the parts, for which, would cost in the vicinity of $200. However, since it was making such a loud noise and water was coming out from underneath the washer, he was certain the transmission was out. He said the noise was an indicator the bearings were gone. I didnt see much point in repairing the washer if the transmission was out because it couldnt be fix.There was a couple at Lowes purchasing a machine at the same time as myself. They said they had a Cabrio also and it was only two years old. It wasnt spinning the clothes either and making a tremendously loud noise. They told us this before we mentioned that we had a Cabrio also. I will neither purchase another Whirlpool product. Junk!

We replaced older GE with the giant front load model that can do king size sheets and comforters. It has worked like a champ. It was a bit more but worth it for us. In a year and a half no issues no problems and I like the control lock feature so I dont keep hitting it off when I go thru the laundry room to the garage.

My fridge is a French door-type with two doors on top and a pull-out freezer with a ton of room! There's water at the door and an amazing ice maker inside the freezer. Two drawers for veggies, fruit, meats/chicken. And a retractable shelf to make room for larger, taller items.

Whirlpool, shame on you! I purchased my Whirlpool Cabrio pair from Best Buy in 2008. Ive had repair technician after repair technician out over 7 times! The washing machine must have been designed by a 3-year-old! Whirlpool, youre getting greedy and youre making your products CHEAP! I know this is fact, I have a 15-year-old side by side in my garage made by Whirlpool and it works great! Fire your 3-year-old designer! I will NEVER buy Whirlpool again! After all said and done, this pair has cost me total purchase and repairs over $4,000! And Now my bearings are bad! Thank God for YouTube! Im fixing it myself this time!

I purchased a brand new washing machine and had service come to repair the machine approximately five times within the first year. Every time the machine was repaired, it was for different reasons. I contacted the main office and spoke to a woman named Sherry who is a supervisor and she was very nasty. This is a brand new machine and I feel that it should be replaced with a new one. Sherry said that there was nothing she can do for me. Is there a lemon law for appliances? The machine is used for my son and me only. I have all appliances in my house by General Electric and this is my first and last experience with Whirlpool.

We saw water all over my wood floor and traced it to the lower freezer unit of my 15-month old refrigerator/freezer. We had to call a repairman which traced the problem to a frozen defrost. He put in a new thermometer at the tune of $200 and now we have to deal with a wood floor problem on top of it. I purchased because Whirlpool was always known to be a quality product. I wont make that mistake again.

Purchased in Nov. 2013, by March 2014 noticed water leak on floor, after 8 service calls in 3 months it was deemed unrepairable By Whirlpool. Got a new fridge in June 2015, no cost to us, but have had 2 service calls already for the same problem. The first leak damaged our kitchen floor, and the ceramic tile that we have is no longer made so we have had to file an insurance claim on our homeowners to pay for repairs. I would never buy any Whirlpool product again, or buy from the local company we bought the original fridge from.

This range is easy to clean, easy to use, multi functional burners, easy to use oven and very nice looking. We use propane instead of natural gas and the conversion was quick and efficient. We absolutely love the griddle.

I purchased a Whirlpool Gold French door with the bottom freezer in October 2013. I had one repair done while it was still under the 1 year warranty, but by the time it was 18 months old, it began leaking refrigerant. I was told by the technician that the cost to repair it would be more than the value of the refrigerator, and the chances of the repair lasting more than 6 months were minimal. I had to buy a brand new refrigerator (not a whirlpool this time). I contacted Whirlpool customer service but they were non-sympathetic. Do Not Buy Whirlpool Products - Poor quality and high prices.

I bought a new home from DR Horton with Whirlpool appliances. All of the kitchen appliances were Whirlpool which came with a 1 year warranty. After closing on the house and getting in, started the dishwasher for the first time, it started leaking water instantly from the bottom of the unit and spilled all over the floor. Tried to contact the builder/inspector who asked us to contact Whirlpool. Called Whirlpool and I was kept on hold for over an hour before someone answered. The rep was so adamant talking all unrelated things and said that she cannot do anything for another 15 days. After escalating to the supervisor, it was the same response. The service at customer care is so bad with no fix in sight. I am not sure what they are going to do with the appliance and not sure whether they come and fix it or keep me waiting. Very unethical, the way they talk to the customers.

I bought a Duet front load washer and dryer set in January 2009 from our local Lowes. Spin cycle noise progressively got louder over time to the point we contacted our locally owned service company to check it out in June 2011. Cause is defective shell and spin tub, total repair cost $750. This was about the original cost of the washer! I contacted Whirlpool via e-mail (wait time via their phone is outrageous), they wont do anything. Out of warranty. Up until now, Whirlpool has had a good name with me. Not anymore. I will never buy anything Whirlpool manufactured ever again. (Maytag, Kenmore, maybe more brands.)American companys insensitivity such as this is what gives some of American industry a bad name and drives consumers away to quality foreign brands made in Europe: German, Swiss, Italian, Swedish,etc.Im going to take a hard look at Bosch washers to replace this Whirlpool piece of junk.

Just bought two new Whirlpool water heaters, $469 each. Not impressed. One of the MANY issues: water leaking from the top. Reason: before installing, if you look inside female threads, you may see a rubber gasket (heat loss valve). One of the two heaters of mine was missing one. This showed me what the quality of the joint was like under the gasket. I temporarily removed the other three (two heaters) to confirm what I saw: At the backside of the threads there should be a clean flat landing from which to the male nipple should tighten against (washer in-between). Instead, there is a disaster of a flimsey lip (washer-like) which is torn up and not anything close to flush. Bad Whirlpool! Bad quality control!

I paid ~$1200 for a new Whirlpool (French door top fridge and pull out freezer bottom) 7 years ago when I bought my house. I was so excited - and the appliance has been a problem from the beginning. It has always made a very loud knocking noise - even when it was new. I was told by the technician there was nothing he could do and Home Depot wouldnt help me with it either. My freezer has gone out three times - the last time was the day before Christmas Eve 2016 (a few days ago). I lost everything for my Christmas dinner that was in my fridge because that went first.Then when the service man came today, I was told it was the freezer that is causing the problem and everything had to be defrosted - plus they had to order a part that would take 3 to 5 days - so Im now going to lose everything in my freezer as well. All in all with the three service calls and the food I have lost probably amounts to around $800 - $900. I am so upset and cannot get any help from anyone. So, Im just warning you - NEVER buy a Whirlpool!

This has been our second Whirlpool Hot Water Tank in our home in the past 14 years. The first was installed by the builder, when it went out we purchased a larger capacity one from Lowes. It was professionally installed and now, after the extended warranty coverage period is expired, its expired as well. I would think you should be able to get more than 7 years out of not one, but two Whirlpool hot water tanks. No wonder they are no longer manufacturing hot water tanks - they sucked at it. Also, if you do have one, you have to get parts from Whirlpool and pay $30 shipping. No thanks, for the cost of parts to replace everything youre better off getting a whole new unit.

In open concept homes, manufacturers need to consider the refrigerator’s noise — ice makers included. We hear every single clink and buzz. We love (and prefer) the french door concept, but the freezer drawer, when it’s fully loaded, is difficult to open and close. Also, the stainless steel scratches WAY too easily.

I bought a Whirlpool water heater in 2009. I paid $588.46 at Lowes. Turns out it is in a class action lawsuit for faulty thermocouple. I was given a coupon from Whirlpool for 2 new thermocouples as part of the class action lawsuit. The thermocouple goes out on it every 1-3 months. You never know when youre going to have a cold shower getting ready for work in the morning. I literally could have bought a new water heater for what Ive spent on thermocouples the last few years. The last two times it went out, I had to replace it twice within 1 day. Im sick of replacing it and have decided to install a new hot water heater. I am disgusted with Whirlpool and tried to contact them about it but have gotten no response. I will never buy another Whirlpool product and would not recommend them to anyone!

I bought the Whirlpool Cabrio model # wtw5500xw2 about two 1/2 years ago. Besides my clothes not clean, I havent have any problems with it until recently. Usually it doesnt spin. The clothes are left soak and wet. First the belt broke, then the lid lock, then the nut came off the pulley, then the splutch assembly. There was a few more problems in there. Now who knows what is wrong with it? It is one problem after another. It is a money trap. The CEO was just after money. There needs to be one big lawsuit against Whirlpool. After I find out what is wrong with it and the cost to fix it, I probably will just go buy a new washer/dryer set. And it will NOT be a Whirlpool.

I feel as though they could use some additional features, it’s also hard to change out some of the wiring in the back. I’ve had some issues with smells coming from the washers as well from them. Hopefully they can start to look into tweaking smaller details to improve the overall machine.

We made a major appliance purchases on July 1, 2010 of a Front Loading Washer and Stackable Dryer. The dryer required servicing at 11 months with was was covered but it required a major service for a broken motor control board. This has nothing to do with regular usage. The cost to repair is over half the total cost of the appliance.This is unacceptable on a 15-month old washer. Whirlpool would not stand behind their product or service. I had to purchase their Repair Plus 1 program to get it fixed. What a racket!

Cabrio Top Load Washer model WTW6800WW1 - Although we were very happy with the vendor where this was purchased and happy with the majority of the washer function; there is a problem with the cabinet & lid connectors rusting. Specifically, the lid connector on the left side totally rusted out, and also around the bleach cup, rust. There are also rust spots where the seam of the top section of the washer meets the bottom part. The washer was purchased in 2009. We have had it serviced in the past, prob 5 years ago, it needed a new motor and the rust was beginning to show then, while under warranty. I recently called Whirlpool and the associate told me that she had never received a call with regard to this type of problem. She did give me names and phone numbers of appliance repair in my area. I find it odd that Whirlpool would not make their associates aware of issues like this. I searched online and saw more than a few complaints about rust. So on it goes, no recourse, and as I read about the problem from others reporting this; it was mentioned that the vapors from the bleach cup etc, contribute to the rust. Additionally, even if it was under warranty, I was told that this is considered cosmetic and it would not be covered. Until... and I can only suppose, that until the lid possibly falls off while lifting, the cosmetic ruling may then turn into a function problem. Now there is also a squeaking sound, so off to call the appliance repair, check the cost and next time... buyer beware. I guess a lesson in science as well, hopefully this design flaw will be corrected for the next models in process.

Model WTW4850OXQO. Purchased this washer in Nov. 2011. Two months ago the washer began making a loud grinding noise in the wash cycle, so loud it can be heard throughout the house. Called the dealer whose serviceman said it was the gearbox and it would need to be replaced. Cost of the gearbox $235.00 plus $165.00 service. Called Whirlpool in TN and was told that I didnt purchase their 1 yr warranty. What the hell is a 1 year warranty but me paying Whirlpool to fix their defective piece of crap in case it breaks in the 1st year. I owned a Kenmore that lasted 11 years, an RCA that lasted 12 years, and a Maytag that lasted 10 years. Never a problem til they died of old age. This piece of ** is breaking down after 3 1/2 years. NEVER buy Whirlpool! Also, the inside of the machine SMELLS. My wife has to use bleach or cleanser to get the smell out. Once again a company in the USA thats too big to care about its customers!

My 4-year old water heater has upper/lower sensor issues for the fourth time this year. The rep was supposed to send replacement parts to arrive today (day four with no hot water), but the wrong ones were shipped. A different rep called and offered to exchange the unit for a new one. The expense to me will be $350-$450 for the plumber to uninstall my unit, take it to Lowes and bring the new one back to install. The plumber suggested I take my $450 and just buy a new non-Whirlpool unit. He knew immediately that I had a Whirlpool hot water heater because its the most common repaired vendor. Whirlpool should be covering this expense for re-installation of their inferior product. Poor customer service. Day 4 with no hot water during the holidays with no solution in sight short of me purchasing a new hot water heater. Whirlpool finally got the right parts to me and I paid a plumber $190 to install. One week to the day later, my pilot light will not stay lit. No change in ventilation since it has been installed. I will say I have been dealing with their rep Chris on the phone who is extremely nice and I feel sorry for him. But we all have the exact same issue which is not being resolved.

My oven is less than 2 years old. The blue enamel has had cracks for over a year & was told its cosmetic & theres nothing that they can do about that. Now its starting to pop off. I found a few slivers in a vegetable dish! Now I cant even use the top oven because of this! It seems to only affect the bottom of the top oven. I feel that the temp may be getting too hot for the blue enamel which is another safety concern. I have contacted Whirlpool/KitchenAid to be told that if they send out a repair person he would just use a marker on chips. I was told they would give me an employee discount from $3000 to $1800 to replace but I would have to act right away for that price! Really? My oven is only 1 & a half old.When I started researching this problem I am having I found many complaints of people having the same problem! As a consumer I feel so mad & frustrated that they are not doing anything about this since its an ongoing complaint from so many dissatisfied consumers. I do believe it is a safety & health risk now that its showing up in the food that has been cooked in that oven. I would urge anyone thinking of buying a Whirlpool/KitchenAid cobalt blue enamel oven not to! They will not stand behind their product & you will have to replace at your own expense. Shame on you Whirlpool!

Thank you Michael of Castleton, NY, for the posting about re-setting the microwave when it stops heating. Even if I have to do it once a month, it beats having to go out and get another one. And when that day inevitably arrives, guess which brand Im steering clear of?

Whirlpool Dryer Model #108409 - This dryer has given me problems within a year of purchasing it. I thought that I was investing into a good product by paying more money, $1677 to be exact. Technicians have been to my house on three different occasions and yesterday the repairman wrote that the dryer in not repairable. Badcock Furniture store in Hinesville, Georgia said that they can do nothing. BWG, who is responsible for the warranty, wants to charge me to have it repaired even against the report of the repairman saying its non repairable. VERY FRUSTRATED WITH WHIRLPOOL... I will never by another Whirlpool product. I bought this product in April of 2012 and it did not make one year before it started giving us problems. The repairman also said that the dryer was probably dropped in transporting it and it could not be detected from just looking from the front view.

Warning: Whirlpool water heaters are junk! Spent $553.00 for a high quality ( lmao ) water heater that had a 6 year warranty. Started leaking internally and rusted through, then rusted a hole in the bottom. 6 years and 3 months later they said you are S.O.L. Leak occurred well over 3 months ago, but they said it has to be reported before the 6 years. Do not waist your money on this junk!

Our Whirlpool refrigerator, model MODGI5FSAXVYO, began leaking water from the freezer onto the floor about 3 months ago. We purchased the unit in January 2011. We had to keep a towel on the floor to absorb the moisture. Our troubles began after the freezer door was left ajar and the interior became quite frosty. We had turned off the freezer several times to defrost but nothing helped until this morning when I read the comments of Marea of McClellanville, SC and Ruth of Vavenby, BC.I then decided to begin exploring taking apart everything until I reached the freezer unit in the back of the freezer. I discovered a lot of ice with the ice blocking the drain hole which is supposed to drain condensation from the freezer fins to a drain pan in back of the freezer. Apparently, leaving the freezer door ajar caused the drain hole and surrounding area to ice up. Condensation from the fins would keep dripping until it overflowed onto the bottom of the freezer until it filled up with ice. The water then had nowhere to go but out of the freezer onto the floor. The simple solution to this problem is to turn off the fridge, empty out the freezer and allow the frozen drain hole to thaw out. You can easily remove the back panel of the refrigerator to see if water is then draining into the drain pain. Good Luck! Ed

I bought a fridge from this company not even 14 months ago. Went away for a week and came home to a fridge and freezer of rotten food. The fridge had died - Im guessing not long after I had gone away by the look and smell of the food and house. I have had nothing but the run around ever since that day. Spoke to this person and then that person. The electrician confirmed that my fridge is completely dead because of the compressor. So they sent a report to Whirlpool and they have now confirmed that I will get a new fridge. Now Im being told that will take 7-14 days. So I have been left with no food whatsoever as well as no fridge. I have two kids and cant even buy shopping for my son to take to school. And now Im being told that I had 9 months left on the warranty for the fridge that died and that’s all I will get on a new fridge. Should I not receive a new warranty for a new fridge? And should they replace my food? Could really do with some feedback on this matter. Please help me.

This dishwasher is poorly constructed. I cannot use it now, as the top racks assemblies have both fallen apart and the rack will not hang. The bottom rack is functioning on 1 wheel assembly out of four. And the one that is functioning is a new one I put on it three weeks ago. The dishwasher is 2 years old. I am very disappointed in Whirlpool, and I will certainly not purchase another one when I buy a new dishwasher.

This was a substitute for model I actually wanted, I was told the one I would receive was the newest model version of the model I wanted. What that meant was it was the stripped down version. It does not get clothes clean nor does it spin/balance the load which causes it to walk around the room. It is only 9 months old and I need a repairman.

I have a top-freezer model WRT5715MYW. This week will mark the 3rd time Ive had a service call to complain about food freezing in the refrigerator compartment. The last time the repairman told me I couldnt place food in the center of the refrigerator since that is where the cold air from the freezer compartment comes down into the refrigerator compartment. This time when I called to schedule the repair call, the woman at the appliance store where I purchased this told me she also has a Whirpool refrigerator and she cant place any food on the bottom shelf of the refrigerator due to freezing. So this 21 cu ft refrigerator has a lot less usable space than I was led to believe when I purchased it. I would not recommend this product due to this reason. Beware of that channel that comes down the center of the back of the refrigerator. It seems like a design flaw to me.

I just purchased a new stove after using my old one for 15 years with the same great quality. Its the brand I will purchase when I have my retirement home built next year and leave my new one in the home for my son so he wont have to buy one for 15/20 years.

11 months after I bought the fridge it started acting up. I paid 1900 for this thing. The temp kept getting warmer and the ice maker quit working. I had to pay for a service plan. Ill never buy a piece of junk Whirlpool product in my life again and ill broadcast their poor quality to everybody in my 5000 congregation. I work to save up to buy this product and its junk. Ill end donating it. Im very upset at this junk product produced by Whirlpool.

Burners always needed replacing and now do not work anymore - Whirlpool range looks nice, but very expensive to maintain. The burners constantly needed replacing, they do not heat up. I got a repair technician to look at it. He replaced the parts that the burners hook into. Now they do not heat up at all. Well, one of four barely boils water. The oven still works, oh great. The thing is only 7 years old. I have had ovens that lasted 20+ years at my dads house or 15 years at another house I lived in. With all the negative comments and the repair guy who tried to fix it, I think it is time to get the kids Easy-Bake Ovens out of the storage or buy a new range. Obviously, it will not be a Whirlpool. So many negative comments people left, my useless top burners seem mild comparatively.

I have had my refrigerator for a few years now. When I first purchased it, it was because of the brand and the looks. As far as performance it runs just as good as any other less expensive ones.

We replaced our kitchen appliances and went with Whirlpool. The oven and Refrigerator havent had any issues yet but the dishwasher has been crap since it was installed. While it looks 10 times better than my old dirty dishwasher it replaced, its main function of washing dishes is 1/4 the of the quality after running two or three times. Not to mention the average cycle time is 4-8 hrs. Dishwashers by design, should be convenient and save time. Whirlpool managed to remove both of those traits from this Dishwasher and now their warranty service said they can send out a technician but I will have to pay for it if it’s not covered under warranty!

This washing machine started giving us trouble just a few months after purchasing. Have had repairman to our home 5 times in 3 years. Last time repairman came he said future repairs would be very expensive & we should purchase another machine. Whirlpool will not have my confidence again unless they recall this machine & fix all problems.

My wife and I went and bought a new Whirlpool 27 cubic foot French door fridge model WRF767SDEMO1 in 3-13-17 from Lowes and I have all the paperwork. And on Monday the May-28-2018 it stopped making ice, so I called a repairman and he came out May-31-2018 and he said it was leaking gas and it cannot be FIXED and it is JUNK. He told me to, Call Whirlpool and tell them you want a new one. I called Whirlpool and they are sending one of their repairmen out June -5- 2018 to check it and by that time I will lose everything in the fridge because it stopped working.

I purchased a Whirlpool Gold top freezer refrigerator (G2IXEFMWQ03) in May 2011. Six months later, the freezer began to collect frost and eventually clogged the refrigerator port from freezer. Since cold air from the freezer was not going to fridge, I had to turn down the refrigerator temp to lowest setting. I had a service person come out and replace Adaptive Defrost Control under warranty - it would have cost me around $250. Now roughly 12 months after repair, the defrost issue is back. The part cost me $175, and that is if I install it myself. I called and mailed Whirlpool which was a waste of time. This is the last Whirlpool I plan to purchase. For the same issue to occur in this short time span, it has engineering flaw written all over it.

This ref model # wrf736Sdam13 is less than 6 months old. The doors have never lined up. At the top is a 3/4 gap and it is 1/4 at the bottom. This is a side by side. Sometimes the left door will open on its own. If you stand to the side and look across the front, the left door sets out about 1/2. My wife and I have contacted whirlpool many times and they will not do anything. I am ready to get another ref and get what I can for this piece of JUNK. We built a new home and purchased all whirlpool appliances and do not like any of them. Will never buy whirlpool again. Very dissatisfied with all – RANGE, DISHWASHER AND THE VENT HOOD. PS, the vent hood sounds like it is crushing ice when you cut it on. Very, very DISSATISFIED with all of them.

Whirlpool Cabrio Elite - I wanted this washer and dryer set to be the best one I ever owned. =( It’s the most I ever spent on a set. I am truly very disappointed. The washer, it is twisting the clothes and sheets so bad. My clothes are falling apart a little bit each time I wash them. I tried so hard to load the washer the way they asked never putting in a full load. The dryer leaves things still wet around the corners and edges. Because everything gets so twisted I had to buy a iron and ironing board just to get the wrinkled out. I hate to iron.

We bought a Whirlpool Cabrio 2 years ago and they are an absolute piece of junk!!! There is only 2 people in our family so its not like we are washing big loads. It doesnt get my clothes clean and the clothes stink. I have followed the directions on cleaning the washer and it does not good. Now my clothes are soaking wet at the end of the cycle so I have to put it on drain and spin just to get most (not all) the water out of them. And when I take my clothes out, they are just as dirty as when I put them in. Called a technician and its going to cost over $400.00 to fix. This is nothing short of robbery!!!! This machine is a piece of junk. I read over 500 reviews on this washer and they all had problems that cost as almost as much as the washer cost to repair. There really needs to be a recall or a class action lawsuit against Whirlpool.

I bought my 50 gallon gas water heater in December 2015. When kicks on it rumbling. I called warranty and they said We will send tech out but I will have pay the labor. Why do I want pay for a tech if the quality issue is the water heater. Need pay $180 for person come out say its defective. No sense to me. Then when they tell me need new water heater pay them for install. You can check my accounts I used to shop Lowes and will no longer do it because of this service.

My Whirlpool side-by-side refrigerator is just 4 years old. When they delivered it, they noticed damage on the bottom which required them to bring me a new refrigerator. The new one had issues with the ice maker that required multiple service calls to fix. The refrigerator door always seemed a bit misaligned as it was a bit lower than the freezer door, but it closed, so I never complained. I was just tired of all the issues! During the last six months, the door started to remain ajar instead of closing completely so that we had to always be sure to apply sufficient pressure to close it tightly. I considered calling in a repair, but it was still closing so I thought I might be overly critical. As it got worse, I realized the door was defective, but one day, it just fell off completely without warning as though the hinges were made of butter!After multiple service calls, a tech reattached the door, but I could see that it would not hold and sure enough, it is starting to remain ajar again. I have contacted the warranty company who is now saying the service tech claimed we were hanging on the door. This repair company the warranty company uses has an F rating with the BBB. Now, Im being told it may take a couple weeks to get another repair company to give them an opinion, but the issue is clear, the door was defective and it looks like they found a way to avoid having to make good on the warranty!

Ive been thru 2 new French door refrigerators with the icemakers in the door. Ive lost all of my food more than 6 times! There is a design flaw and they are no longer making the large models. I finally figured this out after reading multiple reviews from a lot of people with same/similar experiences. The compressor freezes then the loud noise all while the temp slowly lowers and ruining your food before you know whats happening. To add insult to injury... After ordering my THIRD replacement, their contracted installation company wont communicate with me to let me know when it will be delivered. Ive been without a fridge for 3 months! Calling them takes a full morning with hold times over an hour! I will never buy another product from them. I have a taboo LG French door with an ice maker in the door in my other home and it has been perfect for 7 years. Just be very careful and read reviews from people who have owned one for at least a year.

I purchased the Energy Smart Gas Water Heater about a year and a half ago, intending to install right away as part of our upgrades. Just now, I was able to install this replacement to our 30-year-old water heater that was showing problems. When trying to start the unit, I kept getting the response that the lower sensor unit failed. We contacted plumbing companies. We were told they would not work on any Whirlpool models purchased from Lowe’s, because they were the worst hot water heater ever made. I called Whirlpool support. They wouldnt put me through to a tech support person until I was registered in the system. I gave up trying after many minutes of frustration.

I purchased a Whirlpool cook ceramic cook top for our new kitchen. The very first time I made something (it was lentil soup) something stuck to the cook top. I have had a ceramic cook top before for 18 years - never had a problem until the whirlpool cook top. I cannot get it clean. I have tried everything! Such as stove top cleaner designed for whirlpool cook tops ($22), other cook top cleaners, the single edged razor, a scrubby sponge, steel wool, I even resorted to furniture stripper - NOTHING has removed this spot. I am ready to throw out this new stove top! What a huge disappointment this Whirlpool product is.

Whirlpool Cabrio top load washer: nice job Whirlpool! You designed a washer that breaks if you accidentally wash a coin! For the second time in a few months, were fixing our washer because a coin was in a pocket. The coin gets sucked into the discharge pump and sounds like popcorn popping when it drains. It rattles around the inside of the machine’s pump until it breaks the plastic pump housing. You will know when this happens because there will be water on your floor. Did you ever consider a screen to prevent a coin from ruining the washer? God forbid someone leaves a coin in their pocket. Well, if you leave a coin in your pocket and wash your jeans, it will cost you a repair every time with this hunk of junk. This would be my last Whirlpool. It will actually be cheaper to throw this thing out and buy a new one, since it won’t be the last time a coin accidentally makes it into the washer.

I purchased my Cabrio washer in April 2011 from Lowes. Huge mistake. The washer has broken 4 times under normal family of 5 conditions. The last time was in March 2015 - the barring was stuck on the drum failed to allow it to spin. It was stuck to the point where the unit needed to be shop repaired. It took 2 weeks to remove and replace the fail part. I just called service again today for the same noise as last time. It kills me that I spent so much $ on a product from a well-known company only to have it fail so often.

Purchased the Sears Oasis (made by Whirlpool) washer and dryer almost 4 years ago and I have worked on these machines more than the Maytag machine and dryer I used for over 22 years. Electronic and mechanical problems. One recurring problem is loose change working its way into the drain pump on the washer and it knocks a hole in the side of the housing. You later discover it when you go down to the basement and find about 50 gallons on water on the floor. Very poor design! Never happened the first time with the Maytag.

We purchased our Whirlpool Cabrio platinum washer about 3 years ago. I am completely frustrated with it. When it is on spin cycle, it sounds like a freight train going through my house. During the rest of the washing... it squeaks. And right now this is the 5th attempt to wash the same load of laundry. Because it keeps getting unlevel and it will not continue after I move the clothes around to get it level. So I have to start all over. There is not a spin cycle option that is available by itself. Every time I have to choose the rinse/drain/spin option. Obviously it is not under warranty anymore! Only a one year warranty... really pathetic! And when we called they offered us a little discount to buy another one. No thank you!!! Wont ever buy Whirlpool again.