We purchased a Whirlpool Cabrio washer and dryer less than 2 years ago. These are supposed to be high efficiency appliances, but the washer has never cleaned the clothes well and the dryer often has to be run more than once in order to get the clothes dry. Then, about two weeks ago, the washer started making such a loud noise on the spin cycle that it sounded like a jet plane taking off. It was hard to hear the television when it was running. Today, it started screeching and water leaked on the floor. I called the number listed on my manual and was basically told that it would cost half of what we had paid for the machine to fix it. What efficiency, a poor machine that lasts less than two years. We will never buy Whirlpool appliances again.

My Whirlpool Cabrio WTW5550xw0 has had many problems. It started with the lid lock error, replaced it, lasted about 2 weeks, and got another one. I did the diagnostic test that pointed me to the actuator, replaced it. It worked for 2 weeks, got another one, and then another one. I was getting a bad reading from the control panel, replaced it, and that worked for a while. I found out that the actuator had a little water drops on it. I figured that it must be the tub seal, so I replaced it. That lasted about a week and a half, and it started dripping again. Now, I figured it is that the transmission has bad bearings, that causes my tub seal to leak, that causes water drips to go onto my actuator, causing a failure in that, which can give me all kinds of bad readings on the diagnostic test. I have replaced at least half the cost of the original purchase price on a year and a half old washer. I also bought my son a Whirlpool Cabrio washer a few months before I bought mine, and he hasnt had a single problem.

We bought a Whirlpool washer (Model # WTW4900BWO) and dryer (#WED4850BW) and within 2 months I was having problems with the washer AND dryer. Every time I washed a load of clothes, the clothes would have some yucky stuff hanging all over it. I called Whirlpool and was told to try setting the washer on 1 Rinse with Softener even though I never use a liquid softener. Their suggestion did solve the problem, but why doesnt a brand-new washer work the way its supposed to? A short time later, my dryer buzzer stopped working and the knob would not advance when set on the Energy Preferred setting. I called Whirlpool again and was told they did not have a service technician in the area where I lived and that it was not likely that one technician would come on the same day to service both machines. I asked why they would sell their products in an area where they were not willing to service them and they said that is the choice of the store that sold it to me. Then they told me there was a service technician available about 40 miles away and they would fax the order to them so they could contact me. The technician who came did look at both machines and was able to determine that the control panel needed replacing on the dryer, but was not able to do anything about the Rinse Option problem on the washer. He suggested that I continue to follow the recommendation of Whirlpool as long as it works. I can do that, but Im not happy that a new machine does not work the way its supposed to. He also recommended NOT using liquid laundry detergent or fabric softener in my washer because it contains animal fat and can build up and cause problems. Nowhere in the manual did it say that. He took the washer apart and showed me how it was already building up under the washer basket. I told the technician that my laundry has had an unpleasant odor to it when it comes out of the washer and even after it is dry. He said that might be because of the small amount of water that is used in the energy saving washer. If these problems cannot be resolved, I consider this washer to be a lemon and hope it will be replaced with a new one. If I had to do it all over again, I would buy a traditional washer. I liked the idea of conserving water, but not if my familys clothes stinks.

After purchasing 3 whirlpool items in the last 4 years and 2 of them breaking down a dryer last year, and my water heater today. I no longer have faith in your products. I am disabled and was a whirlpool customer, but after my recent experience with your failing products, I will not be purchasing any more! Its great your willing to send the parts for the water heater but, it costs $65 to have them installed. I bought from you because you had a quality item and obviously that is no longer true. Contact me if you still want me as a customer.

We purchased a Whirlpool Cabrio Platinum washer and dryer from HH Gregg and have had continuous issues with the washer. We have had the lid springs replaced two times since we purchased it and they are out again. I called our service company to ask why we have to continue to replace the springs very 6 months and they said it was a problem Whirlpool was having with this unit. I called Whirlpool and after being on the phone for 45 minutes, they told me there was not a recall, but I could buy the parts directly from them for 1/2 price. This amounts to about $20. The repair cost me about $200 every 6 months because it is a difficult installation. Whirlpool is a terrible company to deal with when you have a problem and they do not stand behind their products. I will never buy another Whirlpool product and will tell everyone I know the same.

The dishwasher is less than 2 years old, out of warranty, and will not start. The repairman said the problem is in the electronics. It would cost $500+ to repair.

We purchased the 36 inch Wide 4 Door Refrigerator with Exterior Drawer about three years ago and it broke down twice in that time frame. Then yesterday the freezer part and ice maker have stopped working AGAIN!! We probably have spent $2000 on repairs. Complete disaster of a fridge!! Do not purchase one!!

Sounding like a broken record, this washer is such a disappointment! I had high hopes for this top loader and thought I did enough research. Bought a Cabrio in Oct 2016 and have never liked it. They will have you believe it’s your fault... the wrinkly clothes, the clothes not clean enough, the white marks over all your clothes... you can’t change your detergent or softener enough and change the amount enough... it will still be there. So disappointed??? Want my front loader back!

This diswasher is streamlined and elegantly desiged for any kitchen. It stays externally clean with easy to wipe surfaces. Easy to use controls on the top of the door that cannot be accidentally hit when walking by the item. Plenty of internal space for lots of dishes. Internal silverware rack is easily removalble and not in the way of dishes. It is extremely quiet when running, like a soft hum in the air. A real "bang for your buck".

Best dishwasher Ive ever used, Quiet, extremely clean, priced well for the quality. A really gorgeous piece added to my kitchen. Would highly recommend this product. Up to date. Easy to use. Sleek design. Would be beautiful in any design.

I purchased a Whirlpool duet front load washer on 21 Apr 10 and it has experienced a major failure. It needs a new rear tub and basket, and the parts alone costs $700. The machine is barely four months out of warranty. After a lengthy conversation with a Whirlpool customer service representative, I was told that without an extended warranty, they were very sorry and there was nothing that they could do for me.

I purchased the refrigerator/freezer, Whirlpool model GX5SHDXVQ02, 2 years 10 months ago. It is now not keeping the refrigerator portion of the unit cold or even cool. It is 70 inside the refrigerator although the freezer portion is doing a fine job. This unit is not even 3 years old yet! To top it off, the unit only has one year warranty on any part. The repair person is now here and replacing the control board. This piece alone is costing me $184.12. Then the labor hours and service call. I should have trashed it and bought a new, different brand. Not even three years old. My last refrigerator/freezer lasted 13+ years with no problems.

When I first bought this machine I loved the big tub, but I was concerned that there was no agitator. It confuses me how clothes can get clean if there is nothing to rub them again. Even in the olden days they rub clothes against a board. Well my concern is valid and I believe the washing machine industry needs to go back to the old model, as this new version does not work.Here are all the problems: 1) The machine judges how much water to put in. This doesnt work. I follow the directions and outline the perimeter and dont overload, yet still it just barely puts in enough water to make the clothes wet. Im all for conserving the environment, but enough water needs to be provided to actually get the clothes clean. I would like to be the judge of how much water should be used, so I would like to be able to tell the machine if it is a small, medium or large load. I do believe that the lack of enough water is why the clothes do not come out as clean as they should and why they end up smelling (see #4). 2) There is no agitator, so there is really nothing available to help clean the clothes. Spinning them around like a maniac is not enough, which leads me to the next problem. 3) The clothes come out twisted terribly and then many times come out of the dryer wrinkled because of how hard they were twisted. I tried to select a less harsh spin cycle, but then the clothes are too wet to put in the dryer. There is no happy medium.4) Biggest problem to date: Our clothes/towels have all started smelling. You know that smell when you leave your clothes in the washer too long (like two days) and then put them in the dryer? Its that smell. The clothes/towels dont smell when you immediately take them out, but they do smell at any bit of moisture. When I dry myself off after the shower, I notice the newly washed bath towel smells like a wet dog. I have used the pods, liquid detergent and powder. I dont remember having the smell problem when I first bought the machine and used powder, so I just returned to using powder today. (Ive even tried doubling up on the pods, but the clothes still smell.)This leads me to problem number 5: When using powder in this machine, the machine does not empty the powder container completely, and so the clothes do not get the required amount of detergent. Often there are clumps left over in the powder dispenser, but not always. (This is what led me to go to the pods and liquid detergent in the first place.) But at least with powder (I use Gain) my towels dont stink after the first time I used them.I wouldnt recommend this machine. I really researched machines before I purchased this one, but they all had bad reviews, so how do you pick? And I never look at the good reviews because we all know so many people are paid to rave about products they know nothing about, or it is a company employee writing the review. This machine is a huge disappointment. I am going to try adding a rinse cycle like a previous reviewer suggested. Maybe the extra water will help with the smell. Of course this is not good for the environment though, so this whole way of making washing machines with no agitator and limiting water defeats the energy efficient goal.

I bought my home in 2010 and less than a year my Whirlpool microwave started forming a crack near the handle and today August 22nd, my husband and I are looking at it thinking, this is totally coming apart! My Whirlpool refrigerator had issues also. Stopped cooling less than a year, and I am thankful I had a warranty with it. Of course it was still under the manufacturers warranty. Use to be able to depend on WHIRLPOOL. Now you feel like youre in ONE with their products!

We purchased 3 Whirlpool Gold appliances, fridge, range and over-the-range microwave in 4/2011. Since that time, the fridge needed repair, the microwave door had to be replaced and the range had to be repaired. Now the heating element on the microwave went and Whirlpool will not fix the problem. We purchased the extended warranty through Whirlpool and they are saying it is not worth fixing. We paid $470.00 plus tax and install and now all they are giving us is $348.00. Since we have had repeated problems with these appliances, why not just fix the problem or replace the microwave??? What Whirlpool customer service told me was that would be options for us if we did not purchase their extended warranty. Tell me, is that fair? The cost to repair the microwave was $388.00 and they are giving us $348.00 - do you not think for the $40.00 difference, it would be worth to spend it to keep us happy. We will never purchase another Whirlpool product again and will tell everyone we know not to buy their products.

Best stainless steel built dishwasher we could find in this price range. Well built with lots of room and easy access to both drawers. Easy to clean filters and a nice modern look.

I purchased a Whirlpool Refrigerator with French Doors, Model No. GX5SHDXVD03. Within 1 year and 4 months, I had to replace the defrost control board. I spoke to Whirlpools customer service, George ** said he was sorry for my inconvenience but that he refuses to help in any way because I missed the warranty period by 4 months. I spent $352.74 for the parts and labor and lost hundreds more in food. Do not purchase any Whirlpool products. I was told that the boards have been going out frequently.

My 4-year old water heater has upper/lower sensor issues for the fourth time this year. The rep was supposed to send replacement parts to arrive today (day four with no hot water), but the wrong ones were shipped. A different rep called and offered to exchange the unit for a new one. The expense to me will be $350-$450 for the plumber to uninstall my unit, take it to Lowes and bring the new one back to install. The plumber suggested I take my $450 and just buy a new non-Whirlpool unit. He knew immediately that I had a Whirlpool hot water heater because its the most common repaired vendor. Whirlpool should be covering this expense for re-installation of their inferior product. Poor customer service. Day 4 with no hot water during the holidays with no solution in sight short of me purchasing a new hot water heater. Whirlpool finally got the right parts to me and I paid a plumber $190 to install. One week to the day later, my pilot light will not stay lit. No change in ventilation since it has been installed. I will say I have been dealing with their rep Chris on the phone who is extremely nice and I feel sorry for him. But we all have the exact same issue which is not being resolved.

Whirlpool washing machine M# wtw7340xw2 / S# c14270996 - Bought in 11/26/2012. Never was real satisfied with the way the clothes were washed. They never came out real clean and smelled like there was still soap in the clothes. It has been less than two years and now it will not run. Turn the unit on and all it wants to do is turn on the pump to drain the tub. Im a refrigeration technician and know how to run a diagnostic test Whirlpool has for this machine. I get an LF code which is water long fill so I checked out the water tube which is ok. So the problem is in the circuit board not sensing the water level. To replace this board is around $350 dollars and if I had someone else do the work I would be looking at over $550 dollars. I only paid around $500 dollar for the washer so it does not make any sense to put a new solid state board into this washer which cost as much as the washer. Our old GE washer lasted us for over 20 years and did a better job washing our clothes. There should be a better warranty on these machines than one year. I did not buy the extended warranty because of the cost and I expect that the product should last at least 10 years or more.

I have an oven that is just under two years old - a Whirlpool. After less than a year, the sensor went out and had to be replaced. After less than one more year, the same thing has happened. They covered the first one, but wont help with labor or parts on this one. There is no user error. Its just a cheaply constructed oven.

Bought the Cabrio washer dryer set back on 1-12-13 for my new home and thought it was a good purchase. Well now its March on 2017 and the washer has been slowly getting louder during spin cycle to the point where yup you guessed it the bearing is bad because on a cheap seal that suppose to keep water out. It just cost me just under $600 to get the repair done and from reading other reviews and the fact that I have worked on cars and machines at my employment this will happen again. I wanted to save money on water for the city that I live in charges gold prices per cubic units of water but for the price of repairs to the water saved I am in the red. So once it goes again going back to conventional unit and will never buy anything from this company again. I work in the second largest printing company in the world for 28 years on press and know a bit about quality workmanship. Its really sort of typical on how over the years some good manufacturers cut quality and design in planned obsolescence into their product just to make money for the useless corporate bloat that has taken over. I made the mistake in buying what I thought was a good product from a great company but they just proved me wrong. People do not buy any products from this manufacture and find out what other unit they make and steer away from them too.

We had the same thing happen. We purchased a brand new home and within 6mo the plastic around the handle started breaking off and pieces would fall into any food that was being cooked on the stove. Whirlpool fixed it for free but now the same thing is happening with the new door.

I have been using this brand for many years. My first washer lasted for 30 years..so I will stick with what I know is reliable. It is a great machine. Very simple. I dont need anything fancy. 3 different cycles to choose from.

We bought a fridge in November 2013. Brand new, paid about $2400. After a few months, the fridge wasnt keeping our food cold, was leaking from the ice maker, and wasnt making ice. I called for a repair and about a week later they sent someone out. He assessed it, then came back a week after that to replace the part. Within a month or two later, the same problem. I called for service and was set up with a new company. The repairman called me a couple days later and instead of setting up a time to come in, he says its a common problem, he knows whats wrong, and he will order the part and call me next week to come replace it. A week passed, no word. I tried calling the man back, left several voicemails, and no answer. After another week, I call whirlpool again and tell them I heard nothing from the man and at first they tell me they cant do anything with it since it is an open ticket and I tell them thats not okay. They need to close it, he never even came to the house and assign it to someone else. After they tried multiple times to call the repair company themselves with no answer, they assigned it to a new repair company. Again, it was assessed, a part was ordered and replaced another week later. So now its been well into 9 months of having a worthless fridge. A few weeks after that part was replaced, the problem was back and I called again for repair. I was told if this problem is not solved this time I would be eligible for a replacement fridge. Obviously, it did not work so I called to have a replacement fridge at the end of August. I was told that someone would call me to set it up in 5-7 business days but maybe a little longer since Labor day was right around the corner. I waited, patiently. I called every few days for weeks until mid October and kept getting told it had not been assigned, they are really backed up, it will be just a little bit longer and they will send a message. Mid October, my sister in law called for me and she was told that it was denied because I had not had it serviced within the last 4 weeks. WHAT KIND OF ANSWER IS THAT??? Thats like putting salt on a wound!! I have had spoiled food, constant clean up of leaks, and constant wasted calls to get told that it was denied because it wasnt serviced in the last 30 days while I was waiting for a response from Whirlpool??? So of course I grab the phone and go off. They agree to reopen the case because it was denied for a bad reason. At this point, as I type this, I have been on hold for 55 minutes to speak to yet another supervisor because it has been 2 and a half weeks since they reopened my case and I am told it has not been assigned and the best they can do is send another message.

I purchased a Whirlpool washer (WTW4800Q) in November 2011. Already, it has rust in the tub. The warranty does not cover this. I never really liked the thing since I have had it. It takes much too long. Lid locks and then starts over. Also, warranty is not good. I wouldnt ever buy their product again and suggest no one else should either. I loved Maytag before Whirlpool bought them out. Im putting this one on Craigslist and buying a real washer, a Speed Queen! Yes, Speed Queen has all metal parts and makes a home washer. Just have to find a local dealer. They are there.

Aqualift self clean oven??? I followed the directions on how to clean my oven. I wiped and scraped out spilled residue from the oven. Then started the cleaning process. The sides of the oven were not cleaned even when I wiped them with a damp cloth. Scrubbing and scraping with the tools that came with the oven helped somewhat. The bottom of the oven was not cleaned. I had to continually scrub and scrape to get it looking half clean and even then, there were still spots that would not clean away. I would have preferred an oven that uses oven cleaner, it gets the oven much cleaner and with less scrubbing on my part. All in all I am very dissatisfied with the oven and would never recommend it.

I apparently am one of the lucky ones to have an electric water heater. My unit started giving me failure codes during the Christmas holidays. Each time it would fail, I would get a different failure code indicating the upper element, the lower element, and a sensor failure. After testing all 3 of these components, it was determined to be a controller issue. After speaking with Chris on the phone, he overnighted a new controller to me. I installed the new controller and had no more failures. Hot showers for New Years! Thank you Chris.

Washer doesnt get soap out of clothes. Had tutorial from service man. Must use extra rinse every time and still have soap on dark clothes. Worst washer I have ever owned. Makes washing a lot of extra work and frustration. Have tried everything to no avail. Takes at least three times longer to wash clothes with all the steps I have to take to get soap out. I understand EPA demands for less water usage, but clothes still must be properly cleaned.

My parents 89 and 76 years old bought a Whirlpool fridge a few months ago. A month after purchase fridge built up moisture terribly. Water was laying inside so much seeping on floor. We called, Whirlpool sent serviceman out. Serviceman number 1 put some kind of black tape in the door saying it was the seal. We were just disgusted over this and it didnt work. We called again, serviceman number 2 came out, said bad door, so he ordered door. Serviceman number 3 came out, replaced door. Moisture still in fridge, food isnt staying cool, and you can physically still see gap indoor. We called again. Serviceman number 4 came out and said fridge is not level due to floor in house. But nothing wrong with floor in house. This serviceman pushed on fridge said to my 89 year old dad and 76 year old mother and I quote, Put a piece of wood under this side of fridge. We will not replace this fridge. Now mind the fridge was delivered and set up by Lowes. So now this brand new fridge is no good and we have had no help whatsoever to fix this problem. So my parents whom have been married for 62 years with 5 grown children, 16 grandchildren, a 36 greatgrandchildren and 1 great great grandchild have promised none of us will ever look at another Whirlpool anything much less purchase a whirlpool appliance. Just for the simple fact of how a multi trillion dollar company will not stand behind their warranty nor name. We are disgusted with the whole situation. This is the worst experience any of us have ever had. So no I would not recommend Whirlpool to anyone for the simply fact of the way my parents have been so disrespected by this company. Its horrible to know this kind of behavior is even allowed for employees to disrespect people. The Whirlpool fridge is warped, damaged from the time it was built. The warranty I hold in my hand says and I quote after 3 visits and problem not fixed fridge will be replaced.Well Whirlpool has been out 4 times and has refused to replace it. This couple has worked hard all of there lifes, lives on a fixed income and has just threw away money on a Whirlpool fridge they cant use. So now we have are in the process of hiring a lawyer. Its the principle of Good Vs Evil with Whirlpool. How whirlpool has refused to stand behind the Whirlpool warranty. So Like I said earlier I would never recommend buying any product that has anything to do with whirlpool. Shame on Whirlpool just shame on them.

March 18, 2018. I was called today to inform me that the right front burner on my new stove Model # WEG745H0FS0 (ordered in early September and not delivered until mid-October from Menards) was not operating properly. The flame was noisy and yellow. I inspected it and found that the front burner base was substantially damaged by heat. See photo (Whirlpool stove part damage1). On inspection of the other front burner base, I discovered early signs of the same problem. (Note changes on burner base on the left of the photo.)In this photo (Whirlpool stove part damage2.JPG), you can see the damage to the burner base and also see some changes on the 3 to 5 O’clock position on the burner base on the left of the photo. This stove is less than 6 months old. The fact that the burner parts can be melted indicate poor design and danger to the owner/operator of the stove. Further, the operators manual for the stove I bought does not include any information on the model I have. It has pictures of the range top similar to mine but the model number is completely different. In addition to this, the Aqua-Lift Technology for cleaning the oven is completely ineffective. This is noted in several other reviews of this equipment. The problem noted by the other review became obvious the very first day I tried to use this range. A 2 cup pot spilled all over the cooktop as soon as I put it on the grate.

Whirlpool convection/microwave GMH6185XVS - In 2011, we purchased a whole new kitchen for our home with the top of the line Whirlpool products. The sorry side of this project was our microwave. This product has been terrible for us! It has been removed from our wall 4 times for failing... and four times we have gone for weeks at a time with a big hole in our kitchen wall!! All of the failures were due to the microwave not heating food or drink, and all, according to our local dealership, were for various different reasons. Again, it has failed and our local appliance center who we bought everything from does not want to deal with it anymore. I dont blame them... I dont either!! It looks beautiful up there above our range telling me the time of day... My wife and I are older adults and take very good care of everything we own. There certainly has never been any abuse to this product (not to mention we spend half our year at a winter home so this microwave only is used for 6 months a year). I contacted Whirlpool customer service about the reliability of this product and their response was that it is now not under warranty and we should deal with our local store about repairs. I have a small Sharp microwave sitting on the counter below this crappy excuse for one that stays there all the time in anticipation on the Whirlpool going down!!! The $60.00 Sharp never fails me!! This was our 2nd time around purchasing all Whirlpool products for our house. We did the same thing when we built back in 1990. All appliances performed as they should have back then. It seems Whirlpool integrity has gone downhill. I will never buy another Whirlpool product nor I will recommend to anyone I know to do the same. Good luck to anyone who purchased one of these.

Purchased a Whirpool fridge 1 1/12 - after Sandy, used for about 1 month. Now ready to move home and was told ice maker bad?? Thank god we purchased warranty! I want to know why ice maker is bad regardless covered?

This is the information I tried to send to Whirlpool only to get a message that it was undeliverable: I purchased a set of whirlpool cabrio washer and dryer on 10-23-2013 (model numbers WTW8540BW, and WED8500BW). On 01-25-15 the washing machine failed to power up just over 2 months out of the standard warranty. This wasnt the low end cheap models. With cash discounts we paid over $1600.00 for the set. After a $70.00 dollar charge to the repairman we are told that the unit has a bad electric control board (part # W10761026). And unfortunately the part is on back order until March 1st, 2015 as of right now. So if and when the repairman gets the part and installs it, I get to pay him an additional $260.00. My family has always been such a dedicated Whirlpool appliance purchaser but this is wrong.Oh I almost forget, now I have to rent a washing machine at a cost of $55.00 per month until mine is repaired. I believed I was purchasing Whirlpool quality. The type of quality that doesnt need an extended warranty because Whirlpool is made to last correct? Please assist me in making this situation right and restore my faith in the quality I was raised with in Whirlpool products.

Second time in 3 years our freezer/fridge has gone out. Same symptoms as last time, which was a bad motor. Repaired BY WHIRLPOOL. Completely useless. I don’t expect to have to replace a refrigerator every three years. Especially when I paid $$$$ for it to begin with. DO NOT BUY!! We will be switching brands. And as the installed items in our house start to go (yeah, they’ve already had to service an oven installed at the same time 3 years ago too) they too will be replaced with other brands. You’ve lost a lifetime customer! Shame on you Whirlpool.

This product is JUNK!! We replaced out hot water tank 1-07-11. Worked good for almost 9 months. Then the pilot light keeps going out. We have replaced everything three times already. Now we cant get it lit for nothing. Its blinking 7 times!!! This should not be happening. When you call Whirlpool, you always get some smart ** rep trying to solve your problems over the phone, telling you what its doing. Excuse me, your not here with it, I am. I even had the plumber on the phone, he got so mad at them, he handed me my phone back and said he is not dealing with stupid. They have no clue what they are talking about!! Its crap that we have to pay $30 for them to express mail a part when its the middle of the winter and we have no hot water. Im at my wits end with this hot water tank. Im ready to sue their butts. Sounds like to me by reading all these reviews, a lot of people are having the same issue. We need to do something about this. They had a suite against them but not for my water tank. They were replacing the parts. Ive spent over $1000 from buying it new, having it installed and paying for repairs on the hunk of junk!!!What can we do??? We need to take a stand against Whirlpool. We need to exchange information and contact an attorney and make them pay!!

I dont know who is the bigger idiot. The designer of this washer or me for not reading the countless bad reviews. I bought a Whirlpool 4.3 CU FT TL WTW5000DW machine on 7/19/2015. It does not come close to cleaning clothes. It now takes me three times longer to do laundry because I have to check every piece of clothing for any stains. These are minor stains mind you but, they will not come out unless I use something like Spray and Wash. My time is valuable, maybe I should drag my clothes to the river and beat them on a rock. Very disappointed.

Atlanta Gas Light Company showed up at my door Saturday Jan 16, 2016 citing they needed to do maintenance on our meter. 20 minutes later, he came in and said we had a leak. He checked all of the furnaces and water heater, then zeroed in on my brand new Whirlpool Range (purchased 11/11/15) indicating it had a faulty control valve. This faulty and dangerous range was sold to me by Lowes and manufactured by Whirlpool and we had unknowingly been living with a gas leak for 2 1/2 months! Its notable that Atlanta Gas Light sends our contractors only every 3 years to test for gas leaks. I shudder to think what would have happened had they not done this. Ill never buy another Whirlpool anything. Model Number: WFG320M0BB0.

Three years ago I bought a bottom freezer Whirlpool Gold refrigerator from Lowes. Two days after it was installed, I noticed a pool of water on the kitchen floor. This happened again. I called Lowes and they brought out another refrigerator, same make and model, and took the first one away. A year later the same thing happened. I had it repaired - quite an ordeal for the technician. He had to order a part and found it difficult to actually get into the freezer. Now after a year and a half approximately the same thing is happening. I cant afford to continue the repair bills and dont like the inconvenience (what if this happens when Im away from home?). The pool of water is substantial - its as though the defrost is simply emptying through the front of the freezer onto my floor.

If 0 stars was an option, I would have chosen that. Ive had my own home for 34 years and have had many washing machines over the years. My Whirlpool Cabrio is absolutely the worst washer I have ever encountered. It doesnt get clothes clean and constantly gets out of balance. Whirlpool did a service call and said it is functioning as designed so I was unable to get a replacement. I really hate being wasteful and adding a huge appliance to a landfill but I will be replacing this machine as soon as it fits into my budget. I dont have a receipt to submit because it was purchased by my builder at my request. Do not buy this machine!

GFG461LVT2 - In October of 2010 I purchased a Whirlpool Gold Fridge and Stove. Its been about 3.5 years and two of the caps that go on top of the range burners are chipped. All of the caps are badly stained and despite the manual instructions to wash them in mild soapy water, they do not come clean. They dont come clean using heavy duty Easy Off cleaner. In addition, the seal on the oven door has apparently failed because the glass is foggy on the inside. Today I phoned Whirlpool after going to their website. I first spoke to a parts representative who advised that I would have to pay $47.00 per cap or $115.00 for all five burner caps. I was transferred to another department as I thought I should get the appliance parts and door fixed for free. The appliance is only 3.5 years old. I was told that the appliance is only guaranteed for 1 year and I would have to pay dearly to remedy the two problems. This appliance is Whirlpools Gold series. It supposed to be top-of-the-line - the price tag was certainly top of the line. Im very disappointed in American workmanship and the companys lack of integrity. Not too long ago I purchased a Whirlpool (aka Maytag) front loading washer. I now own a Samsung. The point is that designed obsolescence will force consumers to purchase products made outside of the US because some of us cannot afford to buy or repair appliances, cars, etc., every couple of years.

We have had our dishwasher for over ten years and have had no problems. Its been very reliable. Its a free standing unit on wheels with a butcher block top as we dont have room in the cabinets for a built in. All you have to do is roll it over to the sink and plug it in and hook up the water line which has a quick disconnect. The male half always stays on the faucet.

Whirlpool Duet Steam Front Loading Washer Model #WFW9750WW01 - The washer is only 5 years old and sounds like the space shuttle landing while in the spin cycle. Cost to repair parts only will be $896.87. The bearings among other parts are shot. I will NEVER own another Whirlpool appliance under any circumstance. Angry is putting it lightly!!!

Whirlpool Duet 3.9 cu ft High-Efficiency WFW9451XW00 - Hear my first experience with Whirlpool. I purchased a washer machine 30 April 2014. Guess what - machine stop working suddenly on July 30th, just about three months later. I had a lot of guest from overseas. While they visit me, I did not have my washer machine. How embarrassing. It was big mistake to buy Whirlpool. It is all made plastic inside and they uses cheap Chinese material. Anyway, technician came house to check what the problem was... all control system was burned. He ordered almost 10 parts from Whirlpool on 04 August. Whirlpool scheduled delivery for 20 of August. I called them for them to send the parts faster so my guests could wash their clothes. They send them little faster for August 16. After a day, technician was in the house again. I waited about 3 hours for him to fix my machine. He was really nice guy. He put install all new parts. Just in front of me, new parts broke after 5 minute. Whirlpool still did not contact me about their decision. Today is August 26th... I called them 5 time already - Nobody give me useful info. NO Whirlpool, guys - bad service.

My family purchased a Whirlpool stainless steel dishwasher at Lowes for around $500. We were replacing a very old GE dishwasher which was so loud you had to leave the room anytime you started it because you couldnt even talk over it. We love the new Whirlpool dishwasher. It is so quiet we thought it was broken at first because we couldnt hear it running and even though it cleans exceptionally well we still sometimes have to look to see that the light is on to know that its actually running. The whole family agrees this may be one of the best purchases weve ever made. The only con I could think of is my son and I put the dishwasher in ourselves and this is the first one weve ever done and the instructions werent as clear so we had to redo the piping of the waterlines a couple of times to figure out in what order to be done. But everything hooked up correctly and worked immediately without a problem. Couldnt be happier.

We have had this range in our new home and in use since May, 2019. The first range had to be returned after its first use due to flaking of the interior walls; a problem the company acknowledged. Since then we have been so unhappy with its ability to maintain the oven temperature. Contrary to the instructions, we calibrated the oven temp and found that it would vary up to 20 degrees lower than the set temp. When set to 350, it would come up to that temp and then cut off until it fell to 330 when it would come back up to 350. That is a great differential noticeable in the time it takes to heat an item and which greatly affects baked goods. A similar lack of consistency in control in the range elements is apparent as well. Now those are major defects. Minor defects are: it is NOT a rapid preheat at all, both lights are on when the switch is engaged even though only one oven is in use, there is no clock function when the timer is in use and the range surface is difficult to clean as it streaks which is visible with the black finish.

I purchased the glass top Cabrio a couple of years ago. Without an agitator; it is amazing how nice thick towels come out with holes or rips! Clothes get so twisted. My sister needed a new washer and after telling her the problems with the Whirlpool; she purchased an LG. I have told many people that have purchased an agitator free machine to stock up on Affresh or one of the other tub cleaners... you need them to keep the odor from getting into your clean? clothes. I cannot wait to sell this washer or give it away!!

I had this washer (WTW7990XGO) 5 years and finally had to replace it. It started with the touchscreen. No matter how often it was calibrated it was very frustrating to get it to respond. It would start dinging and going thru all the cycles at random times. Then there was the error code for the door lock. The door lock wasnt the problem, the surround was slightly warped and the door wasnt catching. Warped Im sure from having to literally climb into the machine to retrieve the clothes! Then a few months later it was another error code - the machine wasnt draining fast enough. It didnt drain at all. We had to use a water hose to drain it. After the second time with that, I went and bought a new washer - different brand, dials - no touch screen, and it has an agitator. Unfortunately, I ran into other customers in the appliance department who were having the same issues from 2 other brands of electronic washers. We all went back to as old school as was available.

Immediately after purchasing an entire kitchen of Gold Series kitchen appliances including the refrigerator with bottom freezer in 2/2013 from Lowes we began having issues with the refrigerator. I am not an engineer and dont profess to be, but even I can figure out that the whole thing is a problem based on a design issue. The top drips water consistently and has from the first, which has been addressed numerous times. Ice maker replaced trying to fix the situation two times. The freezer guides were messed up and off from the beginning, and had to be ordered-waited for, then installed. In total a repair person has been here, an inconvenience on our part - 7 or 8 times and we still dont have a refrigerator that works properly!The last time we had someone look at it, there was a part that had to be ordered from, yes, Mexico and we had to wait a week or so and they told us they could rent us a loaner!!! Are you kidding me?? I should have kept the old 26 yr old fridge in my garage that is still working that was built in America! After buying $8000 in appliances and supposedly a top of the line brand name that in the past has shown integrity to their products... I pay my bill each month, because if I didnt someone would put it on my credit. But who puts it on Whirlpools credit? Who is going to hold them accountable and how many complaints must there be in order for someone in the government to step up and do something to a company that is taking tax dollars from our US and sending it to other countries but selling less quality products to those who do pay the taxes? I am ready to sign a petition! I should have gone with the other brand! Any other brand would have given me a better shot than this of having less of an issue! Terrible experience and certainly NOT GOLD! Shame on YOU Whirlpool!

We purchased a whirlpool gas dryer 30 years ago this past February. Its still going strong with 30 years of continuous use!! The only service ever required was a belt change I did myself 18 years ago. Not too bad whirlpool!!

We get the error code F1 in the start of the cycle and when there is 21 minutes left, we have to stop and reset at least 7 times before the water fills. We put a new sensor in for over $200. The second problem is it goes off balance no matter what the load is. I was going to have it fixed (if possible). After reading all the above I wont waste any more money on it and go buy an old fashioned reliable washer. What a piece of money sucking machine especially when I dont have any extra money to waste down the drain. I wish I knew before. There are a lot of people this time of year I would have rather given the money for a needy cause. How disappointed we are with Whirlpool!

I purchased a Whirlpool range from Lowes for $750.00. After 13 months, the digital circuit board went out and cost $580.00 to repair. I thought this was odd since the range was fairly new. The service tech said the boards are a common problem. Two years later, when using the self-cleaning mode, the door was locked and the board was out again. So this must be the issue because that is the same problem that happened the first time. This must be a design flaw! The board cannot handle the heat generated in self-clean mode. Way to go Whirlpool, put the board near the oven door where it is subjected to extreme heat and melts!

My dishwasher is really a simple basic dishwasher. It is efficient and does a good job of cleaning. You can put many items in the top and bottom and the utensil basket can be moved for better cleaning or more room. If I had one complaint that would be that it is a bit too loud but other than that it is wonderful.

We purchased Model WTW81920758200YW0 on September 8, 2012. Its performance has been unsatisfactory, not cleaning the clothes as advertised. Not long after the warranty expired the main bearing failed, bringing a local service technician and we were left with a bill of over $300.00. Yesterday, the machine stopped in mid-cycle. The display went blank and the lid lock would not release. I called a local service company for a visit and the soonest a repairman could show up was next week.A call to a service we had used for the bearing surmised that without knowing the cause of the failure they could only guess that a circuit board was at fault. That visit would be over $300.00 with labor and materials. That was the last straw. We broke the lid lock to retrieve the contents and took a ride to buy another brand of washer. We went back to the appliance store where we purchased this machine to buy a Samsung front loader. The salesman apologized for selling the Cabrio in the first place. Good money after a bad product.

This was the first new appliance that I had actually ever had and I purchased it in October of 2010. After four months, it started make a grinding sound. I called Whirlpool and the repair man replaced the motor. Approximately four months after that, the lid got stuck and the machine would not respond. Same routine as before, but this time the transmission was replaced. While the machine was apart, I noticed the white insulating panel from the bottom was brown in a spot and looked as if it had gotten hot. A month before the 1 year warranty expired, the washer started making an intermittent grinding sound nearly identical to the sound made when the motor went out. This time a different service company was sent out my Whirlpool and the said that nothing was wrong. Now, the machine is out of warranty and has stopped cleaning close and during the spin cycle the you can hear water running into the machine constantly. Last months water bill shows a 40% increase in water consumption when nothing has changed to incur a larger bill. Seeing all these comments makes me wonder why the heck nothing is being done to force recalls on such poor products. Consumers should be treated with a lot more respect than this. I will never recommend a Whirlpool product to anyone I meet. In fact, I will strongly discourage anyone who is contemplating buying a Whirlpool washer machine.

After buying the best washer and dryer out there, I have found out that they are not. Thank you Whirlpool for taking my $2000 and giving me a junk. I know that you do not care one bit. Never again.

Am posting in regards to a brand new dishwasher that I purchased the first part of February 2020 from Menards. The dishwasher I bought is Model # WDT730PAHB and Serial # F94519386. I had the dishwasher 10 days and it stopped working after running only two times. I checked the breaker box and all electrical connections to the machine and it was getting electricity, but would not turn on at all. I called the store to return it and they only have a 7 day return policy. Since then Whirlpool has been contacted and I have had two service calls from Whirlpool. The mother board has been replaced (which I waited two weeks for the part & five hours for a service man) and still it will not come on. Now I am waiting on a wire harness, ordered on March 4th or 5th and still not here. I completely understand wanting to fix a broken machine, however this was a new dishwasher that only worked for 2 washes. I have now been without a dishwasher for almost 2 months, which in light if our current world situation isnt a huge deal, however this is a time when sanitation is very important. I feel like Whirlpool should offer to replace my new machine with a new machine and not something that is refurbished. At this point it is costing more to repair this machine than to just replace it. Every time I call Whirlpool I get the line of we have to repair it. Give me a break. Take care of your customers!!?? #neverbuyawhirpoolproduct

Despite always using the designated (he) detergents and trying many different brands in appropriate amounts, this washer always leaves an ugly white residue on clothes. This happens all the time, requiring whole loads of clothes to be rewashed, sometimes more than once. This defeats the whole purpose of conserving water, which is reflected in our water bill. We also placed the laundry room on the second floor to make it easier for me with my disabilities. I am constantly having to climb the stairs when the machine gets unbalanced in addition to the extra loads from the residue. I was very excited to purchase this machine. Unfortunately, these feelings didnt last long.

5 years and 11 months ago I bought a 50 gallon gas, Whirlpool hot water heater with a 6-year warranty from Lowes. The 2007 water heaters were on sale, so I paid $329 for it. Within 6 months, I replaced the gas valve, and a few months after that, the thermo-couple went out and I replace that. Each time I called Whirlpool and got return authorization numbers for the parts, I still ended up paying for the parts plus labor. A year after that, the igniter went out and I had that replaced. Last year (the day before Thanksgiving), the thermo-couple went out again and I had to have that replaced - and it cost me for the part plus the labor - even though I had a return authorization number. I also replaced the water line connections/hoses to the water heater at that time. The customer service rep for Whirlpool told me at that time if I had another problem with the water heater, they would replace it for free - and the warranty was good until Dec 31, 2013 (this year). NOTE: Every plumber that has come out to fix the water heater and replace the parts stated that they see a myriad of problems with Whirlpool water heaters. They said the parts like the thermo-couples, igniters, gas valves, etc are poorly built and they replace them all the time. On Christmas Eve 2013 (two days ago), the water heater started leaking from the top by the valves - and so much pressure had built up in the heater the new water hose connections burst, spewing water all over the heater closet. I called Whirlpool the day after Christmas (today). At first, they told me they would not replace the heater as it was not in warranty and then I told them what I was told by the service rep last year. She finally agreed that my heater is indeed under warranty and gave me a replacement authorization number but she told me my warranty did not cover labor. I called Lowes. At first, they told me I would have to remove the old hot water heater myself and bring it back to the store in order to get my replacement. I am a 59 year old woman and I take care of my brother, a disable veteran. Although I am in good shape and healthy, I dont have anyone to help me get the gas and water disconnected and help me lift it into my Suburban. The man at Lowes agreed to bring out the the replacement heater and pick up the old one at no charge, but I will still have to pay $299 plus the cost of new hoses to have it installed. By the time the replacement one is installed, I will have paid a little over $1200 for a $329 water heater. I could have installed a tankless one for that, but I cannot see spending that kind of money right after Christmas. If I have one issue with this replacement, I will install a tankless water heater - and it will not be made by Whirlpool or any of its affiliates. My recommendation would be to steer clear of Whirlpool and their products.

It’s a great stove. I love the glass top. Only dislike about mine is that it doesn’t have the self-cleaning option. I’m very weak in arms and have back injury so bending over to clean it myself is not possible.

I purchased cash for our new house and we notice a couple of times the freezer would start to thaw and the light bulb would freeze up. It has been ok for a while now.

Purchased a double wall oven and had it for 13 months. Used it this past Christmas and for the first time used the self cleaning mode. After an hour the power went out and now the oven is dead. Whirlpool service sent me to a local repair company and they want $70 to come out and look at the oven. This seems like a huge problem based on all of the feedback on the web. This is an obvious lemon and Im going to talk all over social media about the poor quality of this product.

We have a 2 1/2 yr. old Whirlpool gas stove. We have had the mechanic here several times as it would not ignite. We also have had the control panel repaired twice as it melted. It is melted again but they will do nothing. I tried to clean the oven with their AquaLift technology and had to re-do it four times and still have residue which appears to be permanent. We are very frustrated with it. We have used Whirlpool appliances for over 40 yrs. but will not buy another. Model#WFG710HOASO, Serial#R21712236.

Model: Whirlpool Professional FF 32 Elite. Purchase date: 06/2009. Problem: Temperature maintenance issue. The basic need of refrigerator - unable to set/maintain temperature. The cooling system is not working! Poor customer service: Representative charged for visit. The representative is unable to find the root cause! Approximate expense of 4-5k with no guarantee of problem being fixed. Better go for other brands like LG, Samsung.

I have clothes that are coming out torn with large holes, especially cotton items. I dont know if it is the washer or dryer.

This machine is junk. It does not get clothes clean. I had jeans that I soaked and were fairly clean when I put them into wash and had another pair of jeans with a little dried mud. My whole load came out filthy. I am having to rewash the whole load after hand cleaning the washing machine. I replaced a machine that was 25 years old that did a better job than this piece of junk now sitting on its place.

Before last Thanksgiving (2020) had installers set up this 3 door bottom freezer 2.4K new Whirlpool Fridge. It immediately froze almost half of the goods (big holiday foods). Whirlpool Tech showed up 3 times of 4 appts and could not repair. He said should work and now we froze Christmas Holiday foods. Different company of Whirlpool Tech was here was here twice, second time he ordered 4 parts and as of March 12, 2020, we can only use about half of our 24.7 cu ft fridge. For almost 6 months we have bins in our garage instead of the fridge...now our garage is too warm for bins of food. Whirlpool refuses to confirm this $24K fridge a lemon. We DESERVE more!

WE had a Kenmore dishwasher and it never got the food off without scrubbing the dishes first. We decided to get a new dishwasher after being very frustrated. We purchased a Whirlpool and noticed a difference instantly. It was quiet, got the dishes completely clean, (no pre-washing like before) and was overall a better fit for our family.

I purchased my first Whirlpool washer in 1959 and have been true to the brand since. This was a big mistake when I bought the WTW4950XW0. At first I thought it was the learning curve on my part with the new technology. The very first wash load was dry on the top layer....never got wet. Then there was the blinking red light .....you could never leave the room and expect it to continue to do anything. One solution I found was to unplug the washer....wait 30 seconds and plug in and follow with lifting the lid and then close the lid followed by holding the start button down for several seconds. This worked sometimes.Very noisy....sounds like a plane taking off after the gears shift and lots of clicking and a long pause to have the water to enter the washer. I have run out of patience. I am going to buy another washer today. I called Whirlpool twice for advice and they offered none but a high dollar repair and no compensation for the lemon I had in my home. Enough is enough.

We purchased our home brand new in June 2010 and with it came all Whirlpool appliances. We started having cosmetic problems with our over the counter microwave about 2 years later (model WMH2175XVS-2). The plastic casing around the door handle started to crack on the top and the bottom and now both pieces are completely gone as they fell off. The handle is still attached and the microwave is usable; however, it looks shoddy. To replace it, we were told by a Whirlpool authorized repair person that you would have to replace the whole door at a cost of $300 or more if you include labor. I am disappointed that this happened and that we cant get it repaired. It makes me think again about purchasing more Whirlpool appliances.

Bought on 9/11/2014 and installed by Lowes installers on the 15th. It quit heating two days later. Called Lowes and they said I would have to call Whirlpool. I did. WP had me metering with a multi-meter until found OTC button was tripped. Then they suggested I troubleshoot the elements and sent me a video. I called Lowes and they said they would replace. Later they called back and said WP would not give them a RA number and for me to call them. I did and the rep after much arguing directed me to call their factory authorized service, A & E. I did and they said it would be 33 days before they could come out. I hung up and called Lowes who called back later and wanted me to call WP again. This time they said they did not have a repair service close enough to come, but I could try buying the lower heating element and replacing it to see if that worked. I said no, the heater was brand new and they needed to fix it. Their next solution was have me contact a local plumber and arrange to troubleshoot, me pay the plumber and then send them the bill. They would reimburse me up to $100.00. Not acceptable and now the button has to be reset every few hours and the water gets scalding hot while it is heating. I called Lowes and they said they would get back to me, but I have little hope of a resolution. Product number is ** SN is ** Model is E2F50HD045V. Bought at Lowes, Lindale, TX.

I have a front load Whirlpool Washer and it has leaked within 6 months of having it. The rubber piece was replaced and it still leaked. Whirlpool wont take responsibility for its product. I have to put towels down around the washer every time I use it because it leaks. I purchased this because it is more economical to use a front load but not when water is leaking from the washer.

We bought the set washer/ drier from Lowes in 2008. The first problem was that it wasnt rinsing well. After finishing the washing cycle, clothes were still dripping water. It took us to make several phones calls to get the problem solved. Also, the clothes were smelling bad and needed to be wash again. Now we are having another situation that it start the wash cycle but it wont finish and shows a code F35 or sud.

Updated on 04/15/2019: Called customer care about my ice maker which have went out for the second time less than two years and the 1st replacement have only been 9 months from today. Unfortunately they tell me it’s out of the one year warranty process and they can’t help me. Well look like the 2nd replacement should have been under warranty still. Their products are a piece of crap and they know it and don’t care because theyre making money off of the consumers. Be aware and advise you to stay away from Whirlpool appliances. They don’t stand behind their brand. There’s no way anyone should have to be making repairs on a new 2000 and sum refrigerator. My old one is 18 yrs old and still working fine no problems, better than this piece of crap. Warning to consumers. Don’t waste your time and especially your money. Didn’t want to give no stars but you have to give at least 1.Original Review: Purchased refrigerator In July of 2017 and had to have ice maker replaced less than a year of having it. Now again ice maker not working again and only been about 9 months from the last replacement. I think there should be a Lemon law on these products. These refrigerator are not cheap and if I buy something new and spend a good amount of money for, I don’t want any headache and worries. That’s the reason for getting a new one.

I have had two Gold Series dishwashers before but the model number I used had been discontinued so I purchased the W10491035A about a year ago in 2013. It has to be the worst dishwashers I have ever had and we have used them for forty years. Its loud. It won’t dry the dishes, and unless you wash I dont mean rinse, most of dishes are not clean, and that is with the recommended detergent. Whatever you do I would suggest not buying this dishwasher. I dont even know why they would offer a machine such as this.

I have had trouble with this AccuBake stove since four months after I bought it in 2011. First, the clean cycle would work intermittently then would not ignite to bake, broil warm or clean. All burners would light intermittently. Every time I had trouble, I called the service tech from Homestead Lumber, where I purchased the product from and he could never find anything wrong. Product would work fine whenever he came out. Finally, it acted up in May of this year while the product was still under warranty and while the service tech was here. The tech replaced the circuit board. One month later, Im still having trouble replacing igniter. Four days ago, Im still having trouble. This stove stinks. Right now, I wish I had my $959 back for the stove and wish Whirlpool had it stuck up their butt.

As long as Whirlpool continues to use JB Hunt for delivery and installation service of their products, I would stay away from ordering. JB Hunt visited my home 3 times, and each time left with the dishwasher as they arrived without the appropriate tools to perform a basic installation. Whirlpool also sent 2 damaged dishwashers that could not be installed. Buyer beware.

A Whirlpool hot water heater in an apartment I own would not stay lit. A plumber came to service and told me I needed a part from Whirlpool and that no one in town carried them. I called Whirlpool and after providing all information about the unit, she informed me that she would not send me the part because the serial number was not registered in my name. I explained to her that I purchased the building and did not install the water heater that a prior owner had installed it. All I wanted was a repair part. The Whirlpool rep refused to sell me a part unless I could provide a bill of sale where I purchased the tank. The part cost $41 which I was more than happy to pay for regardless of any warranty coverage. I have an obligation to provide services to my tenants. Being unable to repair the tank for a problem which appears to be commonplace for this brand, I had to replace with a new tank at a cost of $1380.00.

New range and the faceplate keeps melting. Had it fixed once and it is melting again. I have been trying to contact Whirlpool but to no avail. What is my next step and is anyone else having a problem with this.

We purchased this washer (Whirlpool Cambrio #WTW8000BWO) in December of 2014. It is now 3 1/2 years old and while the washer worked great til just recently, we now have to purchase a different one because this one will cost too much to repair. We did not get the extended warranty. I have since read that the Cambrio has had a lot of problems. Always check the long term owners and what they have to say about the item, would never have purchased this washer had I known what the problems were and that they even were having them they should have taken it off the market til they got the situation fixed.

I join the many who have posted about the Whirlpool Cabrio Washer cracked lid issue. Our Whirlpool Cabrio WTW7800XW2 glass-lid washer suffered the same (inevitable) fate – cracked plastic on the lid at the hinge stress points, after the washer was beyond warranty. Same story - runaround/no help from Whirlpool. Finally bit the bullet and shelled out the $200 for a new lid. HOWEVER, I didnt want to just replace it and have the same issue down the road. I removed the spring-loaded units that support the hinges, hoping to just remove the springs to release the pressure. I found that the springs are integral to holding all the components together in this unit. These are extremely heavy-duty extension springs, so I took them to my hardware store (TrueValue) and found springs the exact same length, but with a smaller wire diameter and thus requiring less force to extend. I replaced the original springs with these (Century Spring Corp. - #C-143 - 9/16”x3”x.054”). The lid operates perfectly, and now there is very little resistance at the hinge stress point. The only difference is there is no longer a “damping” effect when lowering the lid - it must be lowered manually rather than being allowed to fall on its own. That’s a small correction in habit, but will ensure that the replacement lid lasts for the life of the washer.

Bought these Whirlpool Cabrio Platinum combo about three years ago, nothing but junk from the get go! Washer never gets clothes clean, towels always come out smelling mildew and sour no matter what liquid soap you use Tide, Gain, whatever same results. Plus always mold coming from inside tub and yes we use refresh weekly and wash it out on refresh setting. I’m so tired of our towels smelling sour but can’t afford to buy new washer and dryer living on fixed income. If I could these would be in the recycling yard now. From everything I’m reading all new H e machines are crap and energy efficient my foot. I wish for my old style washer and dryer. WHIRLPOOL YOU HAVE LOST A LONG TIME CUSTOMER!

My contractor purchased a Whirlpool NU50T61-403 water heater at Lowes. After several months the gas valve stopped working. Whirlpool sent a replacement gas valve which stopped working after a month. When I complained they offered to send another replacement, which I declined. They also offered to have it repaired by 2 firms which were very poorly rated on Yelp. Whirlpool stubbornly refused any other remedy. As I needed to resolve this right away because tenants were depending on having hot water. I replaced it with another hot water heater. In summary I wasted $570 for 9 months of use.

I purchased it in 2011 for $1100 Canadian. Smooth glass top and true convection. The controls were easy to use, and understand. What bothered me was that it stopped working just after the warranty ran out. I did my research, and found that the newer ranges that have the controls on top at the back have issues with the motherboard overheating, and causing this problem. I did speak to Whirlpool customer service, and managed to convince them to supply the replacement part at no cost. I paid my local dealer to install it. This repair lasted for just over 1 year. Same problem again.This time I could not convince Whirlpool to supply the part. FYI The part in question is the controller. Essentially a motherboard. All the controls are operated through this small computer. It is the only replacement part that costs over $100. Last I checked it was around $450 Canadian. The reason for the fault is overheating. According to the tech that fixed it the first time, it is the most common problem with this style of range. I find this concerning considering the only thing a range does is create heat!Keep in mind that you are virtually held over a barrel. There are only two companies that market their products under multiple names adding up to over 80% of the appliances on the market. They battle for that market by offering more bells and whistles, and less quality. The Range I replaced four years ago was 20 years old. I just replaced my Whirlpool 3 months ago. I went outside of the 80%, and bought a Samsung. Im rolling the dice, and went with induction top. My theory is it will produce less heat because it just heats the pot, not the stove top.Low quality drives me nuts. I want fewer bells and whistles, and more long lasting reliability. I should be able to go my lifetime and only buy two or three ranges. We really like the induction top. It works fast, and doesnt produce too much excess heat. Dual zone oven is a good idea. We werent looking for it, but there was a deal on. The dual zone induction range was only $50 more than the regular one beside it. Now my wife uses it all the time. She will have cookies in one zone, and a casserole for supper in the other. True convection is the other must have. It does a great job cooking everything evenly.

These machines are designed to clean your clothes by rubbing them together which they attempt to do in a minute amount of water. They destroy the fabric, pull the seam out of shape, wrinkle them beyond the point of wearable, do not get them clean and do not get all the detergent out. I have had clothes come out partially dry. They also do not dilute the fabric softener, leaving unremovable stains on your clothes. In addition, they take forever to do a load of clothes even without the extra rinse you need if you want any hope of getting the clothes rinsed. The dryer is the slowest dryer I have ever had. The steam refresh that is supposed to get the hideous wrinkles out of your clothes does not put steam into the dryer. Instead, it sets the dryer to the highest heat so that those clothes you did not want on high heat are now getting it; then it shoots bursts, yes large bursts, of water on them. Your clothes come out a combination of still wrinkles and wet. If you hear of a class action suit, please contact me. These machines should be recalled.

I shouldve read the reviews online about Whirlpool before buying our washer and dryer Duet. 4 years later the main bearing is going out and its 1200 to fix it. No support from them or anything. They did offer a loyalty discount on a new washer... No thanks. Just would be another headache a few years down the road Im sure. Goodbye Whirlpool. Never buying anything from them or their other brands. Ill definitely spread the word too.

I have a small condo and this dryer fit into the appliance closet with a few inches around it. Every home needs a laundry system. I bought the washer and dryer in this model. Whirlpool is great!

Whirlpool WRF993FIFMOO: Refrigerator Problems: the doors do not close, both ice makers went out, The computer on the filtration will go off. Refrigerator had problems maintaining temperature since 8.12.17. The refrigerator no longer works. This is my second unit since 11.09.16. It came from nfm.com.

I bought this Whirlpool America dishwasher because it was cheap. Even though Im Canadian, I like patriotism and I could get behind the American flag logo on the washer. Let me just say, if you like when food comes off your plates, and attaches to your cups, then this is the dishwasher for you. It is always a surprise when you open the door to discover which dishes have been cleaned, and which dishes have inherited the food particles from the now clean dishes. This appliance really helps you work on time management as you are required to wash all your dishes before you put them into the dishwasher. 0/10 would not recommend for anyone who wants clean dishes.

Two-year old Whirlpool Cabrio top load washer; absolute piece of junk! Bearing on the drum howls like a train. Now the master board or some other sensor (under drum) is out. Serviced for the third time and the service repairman states its cheaper to replace than to repair. For a 2 person household, it is reasonable for us to expect more than 2 years from a washing machine. Same experience with Whirlpool 15 years ago. 1st time shame on you; second time shame on me.

Whirlpool Cabrio - I have had the same experience as those others that have written reviews - over $1,600.00 (on sale) - approximately 3 years old and I was just informed by a service repairman that water has leaked from the center of the tub into the motor and it is trashed. I went to the Whirlpool website to chat with a representative and they are sorry but unfortunately, we cannot guarantee there will be no repairs or parts replacements needed as components do deteriorate or fail on occasion due to factors over which we have no control - they went on to say that since the washer is approximately 3 years old there would be no assistance that we would be able to provide toward repairs. I agree that a class action suit should be considered since Whirlpool is taking no responsibility for a machine that costs too much - makes your clothes smell and lasts for such a short time. Highway robbery!! The dryer is no better but at least it is still working (today anyway!).

I purchased a brand-new, $4600 36 gas range online. They finally installed all appliances by 10:30 pm last Friday, July 8, 2011. On Saturday, July 9, 2011, I woke at 2 am to weird smell (gas). I opened all the windows and went back to bed not sure since we never had gas before. Gas company came out that day and determined that the burners were bypassing gas. Jenn-Air said it was normal for some gas to come out and that they have sent the repair technician out three times to not find any leaks. The gas company red-tagged the stove saying it was hazardous. Jenn-Air has terrible customer service. I was on the phone Monday to Friday this week, every day talking with safety managers to supervisors with no results. This will be the LAST Jenn-Air purchase EVER!

On the 27th March 2012 I bought a new Whirlpool 6th Sense washing machine S/N 411048002028 AWOE 9210 - 30 9Kg for E499.00. I brought it home and plumbed it adding in a lime filter on the water line to protect it from limescale. On the 14th September 2016 a service technician replaced the entire drum as the old one made so much noise and the ball bearings are part of the drum. On the 7th June 2013 a technician replaced the drive belt claiming that it moved if a light load was put into the machine. On the same day I added an extension of 3 years Guarantee at Euro 89.00. On the 14th October 2013 a technician examined the machine for a water leak but found nothing and charged me for the call. Out E25.00. I lived with the noise of the spin cycle ever since. The noise got steadily worse until 27th September 2016 when the machine finally packed in. I stripped the machine down to find the ball bearings on the drum completely rusted over so the drum was rotating without the cushioning. On the same day I bought a Bosch machine and decided to forget about the extra guarantee as the offending parts had already been replaced once and did not even last 4 years. I will bring it to the recycling yard later today as that is all it is good for. It was bought in Media World, Orio Center, Bergamo. It was paid for by Gianni ** who is my father-in-law and had a loyalty card for the shop.

Whirlpool Platinum Cabrio Washer wtw8240 - Ive owned this washer for two years. Worst two years of my life. Its leaked since day one. They have attempted to repair the leaking on 5 different repair visits (told me the nozzle that puts the water in the tub doesnt stop in time and it overflows on my floor). Finally it seemed to be somewhat fixed and then it started to sound like a freight train coming through my house. They determined the bearings were worn on my tub and had to replace the whole tub unit. Seven visits. I got one month out of it and it’s leaking again. I am now out of the extended warranty I purchased. This is ridiculous. Isnt there a lemon law on appliances? I know if a dealer attempts 4 or more repairs on your car for the same problem unsuccessfully, it qualifies for the lemon law. $800 for a washing machine that dumps water all over my floor and no one can seem to fix it. Well Im done, Whirlpool. Next time I will purchase a plain washer with no bells or whistles and it wont be made by Whirlpool!

All of sudden without any notice there was such a clatter. We dashed downstairs to see what was the matter. My washer Cabrio was on its side off balance. I hollered what is the matter. We sit it up, see the back side bulge out and with some searching we discovered the balance thingy was broke. Now I bought April 2012 while going through Chemo May 2014. I burying my washing. Call Whirlpool. Well they say I file this away sorry about your luck - lol. Do not buy this washer unless you want another one in two years junk and they will not help. Well they will if you give them more. The 1400 dollars I already gave them for the set is not enough.

We purchased our Whirlpool Duet model WFW9150WW01 13 months ago. The warranty was up at the one year mark. We chose not to purchase the extended service plan. After all, a washer should last at least five years right? Wrong! The front seal has gone bad. It is an $85 part plus shipping, plus hours of my time. So, I purchased a product that is supposed to conserve water and instead I am having to purchase a petroleum-based product (the rubber seal), as it would seem, every year or so! These companies have us snowed with the whole conservation bull! CFLs, High Effeciency, Bio Fuels, etc., its all a hoax! And it is a hoax at our expense. Does anyone just produce a good product anymore? Oh yeah, I forgot... Japan does! Our economy continues to go to hell while other countries are coming online. Get your act together, guys, before we lose everything!

Whirpool Part #WPW10564292 refrigerator handle - I am a property manager who has 264 units. We have only been open for 1.5 years and have had to replace 30-40 door handles because they crack at the top where screws are. We tried calling Whirlpool Customer Service because obviously this is a defect and she said they looked in the system and didnt see any recall or issues. We also asked for a representative from Whirlpool to stop out so we could show them the issues and she said we have nobody in the area. We have 9 service requests outstanding that need a new refrigerator handle. On July 19th, we ordered 3 handles from our distributor and we were told theyre on back order until September 6th. When I called at the end of August to make sure we were on schedule with delivery, I was informed they are now on back order until November 5th. I just called our part rep. this morning and now they said the current part number does not exists and gave me the new part # W11026870, and they are on back order until mid or end of November. I am not going to keep quiet about this issue. We have paid $79.89 per handle on a refrigerator that is only a 1 to 2 years old appliance. I am requesting a returned call or email on what you are going to be able to do for us. This is not right or fair to a company that spent a large amount of money to have your appliances in 264 units.

Bought this refrigerator in June 2018. Had issues with freezer section and service technician came July 19. Issue was resolved but only temporarily. Had another technician come in Oct 3 and was told he had to order a new freezer drawer which should take 3 days. Now being told the drawer won’t arrive until Nov 15. You call that service? It would have taken less time to get a new refrigerator. I would never recommend buying Whirlpool products to anyone. What’s the point in buying a product that you can’t get proper service on.

We replaced our 20+ year old washer and dryer with a Cabrio set. I read the instruction booklet twice to make certain I did everything correctly. Ive washed two loads. Both times, the clothes were in a ball at the bottom of the washer. Everything was horribly wrinkled. DO NOT BUY this WASHING MACHINE UNLESS YOU want your CLOTHES to COME OUT in a WRINKLED BALL.

I purchased this set in November 2013, it is now October 2014. I made the same mistake as many others have made (according to the reviews that I have read on this site). Because I have owned Whirlpool brand appliances before - including washers/dryers - I assumed this new HE machine set would be every bit as good + quality. Unfortunately, I did not do my homework!Everyone is right - this Cabrio HE washer/dryer combo is nothing more than expensive JUNK!. My complaints are all the same as everyone elses: the clothes do not get clean, soap residue remains on clothes, the clothes even have parts of the articles come out of the wash cycle dry not even having had the water touch the articles in areas! The dryer has been repaired once already for a dryer sensor problem & overheating, now both the washer & dryer are making some ridiculous hum-drum noises! Even with the extended warranty that I purchased, I can see the loop holes built into it; theyve got me over a barrel with the nonsense mumble-jumble tactics of having to qualify for adequate service repairs for replacement of parts (3x on each machine) they cant find, before even attempting to negotiate a buyout that will never happen. Never again, Whirlpool anything!!!

We had refrigerator 2 years and compressor went out. Whirlpool would not repair. I will not buy Whirlpool again.